FE Mechanical overview

  • 200 practice questions
  • 34 flashcards
  • 7 study guide topics
  • 56 key terms

What you'll study

  • Mathematics
  • Probability and Statistics
  • Ethics and Professional Practice
  • Engineering Economics
  • Statics
  • Dynamics
  • Mechanics of Materials

The Fundamentals of Engineering (FE) Mechanical exam is one of the discipline-specific FE exams offered by NCEES. Passing the FE is generally the first step toward becoming a licensed professional engineer (P.E.). The exam is intended for recent graduates and students close to finishing an undergraduate engineering degree from an EAC/ABET-accredited program. It is a computer-based exam administered year-round at NCEES-approved Pearson test centers. The FE exam includes 110 questions, and the appointment time is 6 hours, which includes a nondisclosure agreement (2 minutes), tutorial (8 minutes), exam (5 hours and 20 minutes), and a scheduled break (25 minutes). The exam fee is $225, payable directly to NCEES. The FE Mechanical exam tests core mechanical engineering topics such as statics, dynamics, mechanics of materials, mathematics, probability and statistics, engineering economics, and ethics and professional practice. Preparation should focus on the NCEES FE Reference Handbook, solving practice problems under timed conditions, and reviewing weak topics. Results are typically available within 7–10 business days and are reported as pass or fail. This page is an independent study resource and is not affiliated with NCEES.

Common mistakes

Solving statics equilibrium problems by writing only ΣF_x = 0 and ΣF_y = 0 and then trying to solve for three or more unknowns, producing an underdetermined system and a guessed answer under time pressure.

Candidates default to force summation because it is the first method learned, and they forget that a 2D rigid body has three independent equilibrium equations, so moment equilibrium (ΣM = 0) is a required, not optional, equation. Under exam timing, the resulting algebraic dead end is often resolved by picking whichever answer choice 'looks reasonable.'

What to do instead

Before writing any equation, count unknowns and confirm you have a matching number of independent equations. For every 2D body, write ΣF_x, ΣF_y, and ΣM about a point chosen to eliminate the most unknowns (typically a pin or roller reaction). Practice by re-solving the same problem with the moment taken about three different points and verifying identical reactions.

Computing a beam's internal shear and bending moment without enforcing sign conventions consistently, so the maximum moment magnitude and its location come out wrong, and the subsequent bending-stress calculation is off by a factor or a sign.

Textbook sign conventions (positive shear causing clockwise rotation of an element, positive moment causing compression on top) are easy to state and easy to violate mid-problem, especially when a problem starts from the right end of the beam or includes an overhang. Candidates who switch conventions partway through get a diagram that looks plausible but has the peak moment in the wrong place.

What to do instead

Adopt one convention at the start and write it at the top of your scratch work. Build shear and moment diagrams by integrating the load (V is the integral of −w, M is the integral of V) and check that the moment diagram closes to zero at free ends and that the shear jumps by the reaction magnitude at each support. Verify the peak moment by the area method as a cross-check.

Applying the Bernoulli/energy equation or projectile kinematics while mixing unit systems, for example substituting a weight in pounds-force as a mass in slugs, or using g = 9.81 with lengths in inches.

The FE reference material supplies formulas without unit annotations, and US customary problems routinely mix inches, feet, pounds-mass, pounds-force, and slugs. Candidates who have practiced mostly in SI carry over SI mental habits, and the arithmetic error is invisible because the numerical result is dimensionally unremarkable.

What to do instead

Convert every given quantity to a single consistent base set (ft, lb, slug, s or m, kg, N, s) before substitution, and write the units next to each term as you go. Remember 1 slug = 32.2 lbm and that weight in lbf divided by 32.2 ft/s² gives mass in slugs. As a final check, carry units through the algebra and confirm the answer's units match what was asked.

Treating a dynamics problem as pure kinematics when the acceleration is not constant, applying v = v₀ + at to a system with a position- or velocity-dependent force such as a spring or drag.

Constant-acceleration equations are heavily drilled and are the first tool reached for. Problems involving springs, variable forces, or central-force motion require integrating a = dv/dt or using work–energy, and candidates do not pause to check whether acceleration is actually constant.

What to do instead

Before selecting an equation, ask what causes the acceleration and whether it changes with position or velocity. If a spring, gravity varying with altitude, or a velocity-dependent resistance appears, use work–energy (T₁ + V₁ + U₁₋₂ = T₂ + V₂) or integrate the equation of motion. Practice identifying from the problem statement alone which of the three approaches (Newton–Euler, work–energy, impulse–momentum) is cheapest.

Reading a standard normal or t table in the FE reference handbook and using the table entry directly as the probability, instead of recognizing that the tabulated value is a cumulative area from the left and converting for 'greater than' or 'between' questions.

The handbook gives cumulative probabilities, but exam questions are frequently phrased as exceedance probabilities, two-sided intervals, or 'between' ranges. Candidates under time pressure grab the number nearest the z-score and move on, producing an answer that is one minus the correct value and often still present among the distractors.

What to do instead

Sketch the normal curve and shade the region the question asks about before touching the table. Write the probability as a difference of cumulative values, P(a < X < b) = Φ(b) − Φ(a), and use 1 − Φ(z) for right-tail questions. Confirm your answer is between 0 and 1 and that a right-tail answer plus its left-tail complement sum to one.

Computing a confidence interval or hypothesis test with the sample standard deviation but using z critical values, or using the population standard deviation when only the sample value is given.

The distinction between z and t hinges on whether σ is known, and many candidates memorize 'n > 30 means use z' as a blanket rule, which is wrong when σ is unknown and the sample is small. The handbook provides both tables, so both look available and the choice feels arbitrary.

What to do instead

Use the decision rule explicitly: population σ known → z; σ unknown and estimated by s → t with n − 1 degrees of freedom, regardless of sample size (z is an acceptable large-sample approximation only when the problem expects it). Write the rule and the df on your scratch paper before looking up any critical value.

Applying a single discounting formula to an engineering-economics cash flow that has a gradient, an annuity, or a nonstandard timing, for example treating a uniform annual cost as a present worth by multiplying by n instead of using the (P/A, i, n) factor.

Candidates memorize the compound-interest factor table symbols loosely and then substitute the wrong factor, or they use the factor for the wrong quantity (P/F where P/A is needed). Cash flows that begin at year 1 versus year 0 are also a frequent source of an off-by-one period error.

What to do instead

Draw a cash-flow diagram with every arrow dated before choosing a factor, and label each arrow as a single amount, an annuity, or a gradient. Convert everything to a single equivalent value at one date using the correct factor from the handbook table, then move that value to the comparison date. Check plausibility: a present worth of a cost stream must be larger than any single annual cost.

Choosing between alternatives by comparing only first costs or only annual costs, rather than converting both alternatives to a common equivalent basis over a common study period.

Problems often present alternatives with different lives, and comparing a 5-year option to a 10-year option on annual cost alone silently ignores the replacement cost of the shorter-lived alternative. Candidates also forget that the alternative with the lower first cost can have the higher life-cycle cost.

What to do instead

State the study period first. If lives differ, either use a common multiple of the lives, use capitalized cost for infinite-life comparison, or convert each alternative to an equivalent uniform annual cost over its own life and compare those. Never compare a present worth to an annual cost; both alternatives must be expressed in the same equivalence class and over the same horizon.

Answering ethics items by selecting the option that protects the employer's or client's interest, or that follows the supervisor's instruction, rather than the option that protects public health and safety and the engineer's obligation to report.

Candidates read ethics questions as workplace-politics questions and apply ordinary loyalty instincts. The professional codes, however, rank public safety first, require that a technical judgment be made by the competent engineer rather than by management, and require disclosure of a violation to the appropriate authority when informal resolution fails.

What to do instead

For every ethics item, identify the paramount obligation before reading the options: hold paramount public safety, perform only within your competence, be objective and truthful, and avoid conflicts of interest. Eliminate any option that defers a technical safety judgment to a non-engineer or that conceals a known violation. When two options remain, choose the one that escalates through proper channels rather than the one that stays quiet.

Attempting to solve every problem in sequence, spending many minutes on one difficult item, and leaving later easy items unanswered.

The exam is a fixed-length, computer-delivered test with a per-session time limit, and candidates underestimate how much a single derivation-heavy problem costs. Because the questions are not ordered by difficulty, an early hard item can consume the budget for several straightforward ones.

What to do instead

Set a personal per-question budget (roughly the total minutes divided by the number of questions) and enforce it with a hard stop; mark and move on when exceeded. On a second pass, answer every remaining item, since there is no penalty for a wrong answer and an eliminated-choice guess beats a blank. Practice under a timer with mixed-topic sets so the pacing habit is trained, not just understood.

Exam requirements can change. Confirm current details with the exam provider.

FE Mechanical practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Mathematics

    A simply supported beam of length 6 m carries a uniformly distributed load of 4 kN/m over its entire span. What is the magnitude of the maximum bending moment, in kN·m?

    1. 36
    2. 24
    3. 18 Correct answer.
    4. 12

    Explanation

    For a simply supported beam with a uniform load w over span L, the maximum moment is wL²/8, occurring at midspan. Substituting w = 4 kN/m and L = 6 m gives 4(36)/8 = 18 kN·m. The reaction at each support is wL/2 = 12 kN, which is a force, not a moment.

  2. Question 2Mathematics

    A right triangle has legs of length 3 and 4. What is the sine of the angle opposite the leg of length 3?

    1. 0.60 Correct answer.
    2. 0.75
    3. 1.33
    4. 0.80

    Explanation

    The hypotenuse is the square root of (3² + 4²), which is 5. The sine of the angle opposite the side of length 3 equals opposite over hypotenuse, or 3/5 = 0.60.

  3. Question 3Mathematics

    Evaluate the definite integral of 2x with respect to x from x = 1 to x = 3.

    1. 9
    2. 4
    3. 8 Correct answer.
    4. 6

    Explanation

    The antiderivative of 2x is x². Evaluating x² at the upper limit and subtracting its value at the lower limit gives 3² − 1² = 9 − 1 = 8.

  4. Question 4Mathematics

    A vector has components (6, 8). What is its magnitude?

    1. 48
    2. 10 Correct answer.
    3. 7
    4. 14

    Explanation

    The magnitude of a vector with components a and b is the square root of (a² + b²). Here that is the square root of (36 + 64), which is the square root of 100, or 10.

  5. Question 5Mathematics

    In a standard normal distribution, approximately what fraction of observations lie within one standard deviation of the mean?

    1. 95 percent
    2. 68 percent Correct answer.
    3. 50 percent
    4. 99.7 percent

    Explanation

    The empirical rule states that about 68 percent of a normal distribution falls within one standard deviation of the mean. About 95 percent falls within two standard deviations and about 99.7 percent within three.

  6. Question 6Mathematics

    What is the derivative with respect to x of the function f(x) = 5x³?

    1. 3x²
    2. 15x³
    3. 15x² Correct answer.
    4. 5x²

    Explanation

    The power rule multiplies the coefficient by the exponent and then reduces the exponent by one. Applying it to 5x³ gives 5 times 3 times x², which is 15x².

  7. Question 7Mathematics

    Convert the angle 150 degrees to radians.

    1. 2π/3
    2. 5π/6 Correct answer.
    3. 7π/6
    4. 3π/4

    Explanation

    To convert degrees to radians, multiply by π/180. Thus 150 times π/180 equals 150π/180, which simplifies to 5π/6.

  8. Question 8Mathematics

    A system of two linear equations is graphed as two straight lines. Under which condition does the system have infinitely many solutions?

    1. The two lines are perpendicular
    2. The two lines coincide Correct answer.
    3. The two lines intersect at exactly one point
    4. The two lines are parallel and distinct

    Explanation

    A linear system has infinitely many solutions when the equations describe the same line, so every point on that line satisfies both. Distinct intersecting lines give one solution, and distinct parallel lines give none.

  9. Question 9Mathematics

    A force of 200 N acts at an angle of 30 degrees above the horizontal. What is the horizontal component of the force, in N?

    1. 100
    2. 115
    3. 200
    4. 173 Correct answer.

    Explanation

    The horizontal component equals the magnitude times the cosine of the angle from the horizontal. Thus 200 cos 30° = 200(0.866) ≈ 173 N. The sine would give the vertical component.

  10. Question 10Mathematics

    A steel bar 2 m long is heated and its temperature rises by 50 °C. If the coefficient of linear thermal expansion is 12 × 10⁻⁶ per °C, what is the change in length, in mm?

    1. 2.4
    2. 12
    3. 1.2 Correct answer.
    4. 0.6

    Explanation

    Thermal expansion is ΔL = αLΔT. Substituting gives (12 × 10⁻⁶)(2 m)(50 °C) = 1.2 × 10⁻³ m, which equals 1.2 mm.

  11. Question 11Mathematics

    A simply supported beam of length 4 m carries a concentrated load of 10 kN at its midpoint. What is the maximum bending moment, in kN·m?

    1. 40
    2. 5
    3. 20
    4. 10 Correct answer.

    Explanation

    For a central point load P on a simply supported span L, the maximum moment is PL/4 at midspan. Substituting gives (10)(4)/4 = 10 kN·m.

  12. Question 12Mathematics

    What is the determinant of the 2×2 matrix with rows (3, 5) and (2, 4)?

    1. 12
    2. 22
    3. 7
    4. 2 Correct answer.

    Explanation

    For a 2×2 matrix with entries a, b in the first row and c, d in the second, the determinant is ad − bc. Here that is (3)(4) − (5)(2) = 12 − 10 = 2.

  13. Question 13Mathematics

    Evaluate the limit as x approaches 2 of (x² − 4)/(x − 2).

    1. 0
    2. The limit does not exist
    3. 4 Correct answer.
    4. 2

    Explanation

    Factoring the numerator gives (x − 2)(x + 2), so the expression simplifies to x + 2 for x not equal to 2. As x approaches 2, x + 2 approaches 4, so the limit is 4 even though the function is undefined at x = 2.

  14. Question 14Mathematics

    A sample of 10 measurements has a mean of 50 and a sample standard deviation of 4. What is the standard error of the mean?

    1. 1.26 Correct answer.
    2. 12.65
    3. 0.40
    4. 4.00

    Explanation

    The standard error of the mean equals the sample standard deviation divided by the square root of the sample size. Here that is 4 divided by the square root of 10, approximately 4/3.162 ≈ 1.26.

  15. Question 15Mathematics

    A right circular cylinder has a radius of 3 cm and a height of 10 cm. What is its total surface area, in cm², to the nearest whole number?

    1. 188
    2. 94
    3. 283
    4. 245 Correct answer.

    Explanation

    Total surface area equals 2πr² for the two ends plus 2πrh for the lateral surface. That is 2π(9) + 2π(3)(10) = 18π + 60π = 78π ≈ 245 cm².

  16. Question 16Mathematics

    The position of a particle is given by s(t) = 3t² − 12t + 5, where s is in meters and t in seconds. At what time is the particle momentarily at rest?

    1. 4 s
    2. 1 s
    3. 2 s Correct answer.
    4. 6 s

    Explanation

    Velocity is the derivative of position, so v(t) = 6t − 12. Setting velocity to zero gives 6t = 12, so t = 2 s. At that instant the particle reverses direction.

  17. Question 17Mathematics

    Two forces act at a point: 8 N directed east and 6 N directed north. What is the angle of the resultant measured from the east direction?

    1. 53.1 degrees
    2. 45.0 degrees
    3. 60.0 degrees
    4. 36.9 degrees Correct answer.

    Explanation

    The resultant has an east component of 8 N and a north component of 6 N. Its angle from east is the arctangent of 6/8, which is arctan 0.75 ≈ 36.9 degrees.

  18. Question 18Mathematics

    A simply supported beam of length 8 m has a concentrated load of 12 kN located 2 m from the left support. What is the reaction at the left support, in kN?

    1. 12
    2. 6
    3. 3
    4. 9 Correct answer.

    Explanation

    Taking moments about the right support, the left reaction times 8 m equals the load times its distance from the right support, which is 6 m. Thus R_left = 12(6)/8 = 9 kN.

  19. Question 19Mathematics

    What is the value of the expression 5!/(3!·2!)?

    1. 10 Correct answer.
    2. 20
    3. 120
    4. 60

    Explanation

    This is the binomial coefficient for choosing 2 items from 5. Computing gives 120/(6·2) = 120/12 = 10.

  20. Question 20Mathematics

    A vector function r(t) = (2t, t²) describes a path. What is the unit tangent vector at t = 1?

    1. (1/√2, 1/√2) Correct answer.
    2. (2, 1)
    3. (2, 2)
    4. (1, 1)

    Explanation

    Differentiating gives r'(t) = (2, 2t), so at t = 1 the tangent is (2, 2). Its magnitude is 2√2, and dividing gives (1/√2, 1/√2), which has unit length.

  21. Question 21Mathematics

    A cantilever beam of length 3 m carries a uniformly distributed load of 5 kN/m over its full length. What is the magnitude of the fixed-end moment, in kN·m?

    1. 22.5 Correct answer.
    2. 45
    3. 7.5
    4. 11.25

    Explanation

    For a cantilever with a uniform load w over length L, the fixed-end moment is wL²/2. Substituting gives 5(9)/2 = 22.5 kN·m. This moment is larger than the midspan value for a simply supported beam of the same span because the cantilever carries the full load at one support.

  22. Question 22Mathematics

    Evaluate the integral of x·eˣ with respect to x from 0 to 1, to three decimal places.

    1. 0.718
    2. 0.500
    3. 1.718
    4. 1.000 Correct answer.

    Explanation

    Integration by parts with u = x and dv = eˣ dx gives x·eˣ − eˣ. Evaluating at x = 1 gives 0, and at x = 0 gives −1, so the definite integral is 0 − (−1) = 1.000.

  23. Question 23Mathematics

    In a normal distribution with mean 100 and standard deviation 15, what is the z-score of a value of 130?

    1. 3.00
    2. 0.30
    3. 1.50
    4. 2.00 Correct answer.

    Explanation

    The z-score is the difference between the value and the mean divided by the standard deviation. Here that is (130 − 100)/15 = 30/15 = 2.00.

  24. Question 24Mathematics

    A 2×2 matrix has eigenvalues 3 and 5. What are its determinant and trace, respectively?

    1. 15 and 2
    2. 15 and 8 Correct answer.
    3. 8 and 15
    4. 2 and 8

    Explanation

    For any square matrix, the determinant equals the product of its eigenvalues and the trace equals their sum. Thus the determinant is 15 and the trace is 8.

  25. Question 25Mathematics

    A projectile is launched at 40 m/s at an angle of 30 degrees above the horizontal over level ground. Neglecting air resistance and using g = 9.81 m/s², what is the horizontal range, in meters?

    1. 71
    2. 141 Correct answer.
    3. 163
    4. 82

    Explanation

    Range for a projectile over level ground is v² sin(2θ)/g. Substituting gives (1600)(sin 60°)/9.81 = (1600)(0.866)/9.81 ≈ 141 m.

  26. Question 26Mathematics

    For a function f(x) that is continuous on the closed interval [a, b] and differentiable on the open interval (a, b), with f(a) = f(b), Rolle's theorem guarantees the existence of at least one number c in (a, b) such that which condition holds?

    1. f'(c) = 0 Correct answer.
    2. f'(c) = [f(b) − f(a)] / (b − a)
    3. f(c) = 0
    4. f''(c) = 0

    Explanation

    Rolle's theorem is a special case of the mean value theorem where the function values at the endpoints are equal. Because f(a) = f(b), the average rate of change over [a, b] is zero, so the theorem guarantees a point c where the instantaneous rate of change f'(c) equals zero. This means the tangent is horizontal at some interior point.

  27. Question 27Mathematics

    Evaluate the definite integral ∫₀¹ (2x + 1) dx.

    1. 2 Correct answer.
    2. 3
    3. 4
    4. 1

    Explanation

    Find an antiderivative: ∫(2x + 1) dx = x² + x + C. Evaluate from 0 to 1: (1² + 1) − (0² + 0) = 2. Thus, the value of the definite integral is 2.

  28. Question 28Mathematics

    The position of a particle moving along a straight line is given by s(t) = t³ − 6t² + 9t + 2, where s is in meters and t is in seconds. At t = 2 seconds, what is the acceleration of the particle, in m/s²?

    1. 6
    2. −6
    3. 12
    4. 0 Correct answer.

    Explanation

    Acceleration is the second derivative of position with respect to time. First, velocity v(t) = s'(t) = 3t² − 12t + 9. Then acceleration a(t) = v'(t) = 6t − 12. At t = 2, a(2) = 6(2) − 12 = 0 m/s².

  29. Question 29Mathematics

    A tank initially contains 100 liters of water with 10 kg of dissolved salt. Brine containing 0.2 kg of salt per liter flows into the tank at a rate of 5 L/min, and the well-mixed solution flows out at the same rate. Set up the differential equation for the amount of salt Q(t) in kg at time t in minutes. Which differential equation correctly models this system?

    1. dQ/dt = 1 − Q/20 Correct answer.
    2. dQ/dt = 1 − Q/100
    3. dQ/dt = 1 − Q/10
    4. dQ/dt = 0.2 − Q/20

    Explanation

    The rate of salt entering is (0.2 kg/L)(5 L/min) = 1 kg/min. The concentration in the tank is Q/100 kg/L, and the outflow rate is 5 L/min, so salt leaves at (Q/100)(5) = Q/20 kg/min. Therefore, the differential equation is dQ/dt = 1 − Q/20.

  30. Question 30Probability and Statistics

    A tensile test specimen has a yield strength that is normally distributed with mean 350 MPa and standard deviation 25 MPa. What is the probability that a randomly selected specimen yields below 325 MPa?

    1. 0.0228
    2. 0.3413
    3. 0.1587 Correct answer.
    4. 0.8413

    Explanation

    Convert to a standard normal score: z = (325 - 350)/25 = -1.0. The standard normal table gives the cumulative probability below z = -1.0 as 0.1587, so about 16 percent of specimens fall below 325 MPa.

  31. Question 31Probability and Statistics

    In a manufacturing process the number of surface defects per casting follows a Poisson distribution with a mean of 2.0 defects per casting. What is the probability that a casting has exactly zero defects?

    1. 0.1353 Correct answer.
    2. 0.2707
    3. 0.4060
    4. 0.5000

    Explanation

    The Poisson probability of exactly k events is P(k) = e^(-lambda) * lambda^k / k!. With lambda = 2.0 and k = 0 this reduces to e^(-2.0) = 0.1353.

  32. Question 32Probability and Statistics

    A sample of 16 steel rods has a mean diameter of 25.02 mm and a sample standard deviation of 0.08 mm. Which distribution is appropriate for constructing a confidence interval on the true mean diameter?

    1. F distribution with 15 and 15 degrees of freedom
    2. Chi-square distribution
    3. Student t distribution with 15 degrees of freedom Correct answer.
    4. Standard normal distribution

    Explanation

    When the population standard deviation is unknown and estimated from a small sample, the sample mean follows a Student t distribution with n - 1 degrees of freedom. Here n = 16, so 15 degrees of freedom applies.

  33. Question 33Probability and Statistics

    A quality engineer records the number of rejected parts per shift for 40 shifts. Which graphical tool is best for displaying the frequency distribution of this discrete count data?

    1. Scatter diagram
    2. Pareto chart
    3. Histogram Correct answer.
    4. Control chart

    Explanation

    A histogram displays how often values or ranges of values occur and is the standard tool for showing a frequency distribution of measured or counted data. Scatter diagrams show relationships between two variables, and control charts track a process over time against limits.

  34. Question 34Probability and Statistics

    A random variable X takes the values 1, 2, and 3 with probabilities 0.2, 0.5, and 0.3 respectively. What is the expected value of X?

    1. 2.0
    2. 2.5
    3. 1.8
    4. 2.1 Correct answer.

    Explanation

    The expected value is the probability-weighted sum: E(X) = 1(0.2) + 2(0.5) + 3(0.3) = 0.2 + 1.0 + 0.9 = 2.1.

  35. Question 35Probability and Statistics

    Which statement correctly describes a Type I error in hypothesis testing?

    1. Failing to reject a true null hypothesis
    2. Rejecting a false null hypothesis
    3. Rejecting a true null hypothesis Correct answer.
    4. Failing to reject a false null hypothesis

    Explanation

    A Type I error occurs when a true null hypothesis is rejected, and its probability is controlled by the significance level alpha. A Type II error is the opposite failure, failing to reject a false null hypothesis.

  36. Question 36Probability and Statistics

    The diameters of a batch of shafts are normally distributed with mean 30.00 mm and standard deviation 0.10 mm. What proportion of shafts has a diameter between 30.00 mm and 30.15 mm?

    1. 0.3413
    2. 0.4987
    3. 0.4332 Correct answer.
    4. 0.1500

    Explanation

    The upper limit corresponds to z = (30.15 - 30.00)/0.10 = 1.5. The area between the mean and z = 1.5 is 0.4332, which is the requested proportion.

  37. Question 37Probability and Statistics

    A sample of 25 measurements yields a sample variance of 16. What is the standard error of the sample mean?

    1. 4.00
    2. 0.64
    3. 0.16
    4. 0.80 Correct answer.

    Explanation

    The standard error of the mean is s/sqrt(n). With s = sqrt(16) = 4 and n = 25, the standard error is 4/5 = 0.80.

  38. Question 38Probability and Statistics

    A process produces parts whose length is normally distributed with mean 50 mm and standard deviation 2 mm. A part is rejected if its length is below 46 mm. What is the probability of rejection?

    1. 0.0228 Correct answer.
    2. 0.0455
    3. 0.1587
    4. 0.0013

    Explanation

    The rejection threshold is z = (46 - 50)/2 = -2.0. The standard normal cumulative probability below -2.0 is 0.0228, so about 2.3 percent of parts are rejected.

  39. Question 39Probability and Statistics

    Two independent assembly operations each have a probability of 0.05 of producing a defect. What is the probability that a unit passing through both operations has at least one defect?

    1. 0.9500
    2. 0.1000
    3. 0.0975 Correct answer.
    4. 0.0025

    Explanation

    For independent events, the probability of no defect in either operation is (0.95)(0.95) = 0.9025. The probability of at least one defect is 1 - 0.9025 = 0.0975.

  40. Question 40Probability and Statistics

    A sample of 10 bearings has a mean clearance of 0.250 mm and a sample standard deviation of 0.010 mm. What is the 95 percent two-sided confidence interval for the mean clearance? Use t(0.025, 9) = 2.262.

    1. 0.2404 to 0.2596 mm
    2. 0.2429 to 0.2571 mm Correct answer.
    3. 0.2480 to 0.2520 mm
    4. 0.2438 to 0.2562 mm

    Explanation

    The margin of error is t * s/sqrt(n) = 2.262 * 0.010/sqrt(10) = 2.262 * 0.003162 = 0.00715. Adding and subtracting this from 0.250 gives roughly 0.2429 to 0.2571 mm.

  41. Question 41Probability and Statistics

    A sample of 100 parts has a sample mean of 12.4 N and a known population standard deviation of 0.8 N. Test the null hypothesis that the true mean is 12.2 N against a two-sided alternative at the 0.05 significance level. What is the test statistic and conclusion?

    1. z = 0.25; fail to reject the null hypothesis
    2. z = 2.50; reject the null hypothesis Correct answer.
    3. z = 1.96; fail to reject the null hypothesis
    4. z = 2.50; fail to reject the null hypothesis

    Explanation

    The test statistic is z = (12.4 - 12.2)/(0.8/sqrt(100)) = 0.2/0.08 = 2.50. Since 2.50 exceeds the critical value of 1.96 for a two-sided test at alpha = 0.05, the null hypothesis is rejected.

  42. Question 42Probability and Statistics

    A random sample of 400 customers shows that 240 prefer a new design. What is the standard error of the sample proportion?

    1. 0.0006
    2. 0.6000
    3. 0.0010
    4. 0.0245 Correct answer.

    Explanation

    The sample proportion is 240/400 = 0.60. The standard error is sqrt[p(1-p)/n] = sqrt[(0.60)(0.40)/400] = sqrt(0.0006) = 0.0245.

  43. Question 43Probability and Statistics

    A system consists of three independent components in series, each with a reliability of 0.95. What is the reliability of the system?

    1. 0.9000
    2. 0.8574 Correct answer.
    3. 0.9975
    4. 0.9500

    Explanation

    For components in series, the system works only if all components work, so the reliability is the product of the individual reliabilities. Here 0.95^3 = 0.8574.

  44. Question 44Probability and Statistics

    A sample of 20 welds has a sample variance of 0.0045 mm squared. A chi-square test of the null hypothesis that the true variance is 0.0030 mm squared gives a test statistic of (n-1)s^2/sigma0^2. What is the value of the test statistic?

    1. 19.00
    2. 30.00
    3. 0.0150
    4. 28.50 Correct answer.

    Explanation

    The chi-square statistic is (n - 1)s^2 / sigma0^2 = 19 * 0.0045 / 0.0030 = 0.0855/0.0030 = 28.50.

  45. Question 45Probability and Statistics

    A process is monitored with a control chart for the mean. Which situation indicates that the process mean has likely shifted and warrants investigation?

    1. Two consecutive points lie close to the center line
    2. One point falls slightly inside the upper control limit
    3. Points alternate above and below the center line
    4. Nine consecutive points fall on the same side of the center line Correct answer.

    Explanation

    A run of nine consecutive points on one side of the center line is a standard run rule indicating a sustained shift in the process mean. Isolated points inside the limits and alternating patterns are consistent with common-cause variation.

  46. Question 46Probability and Statistics

    A random sample of 50 measurements is drawn from a population with mean 100 and variance 225. What is the probability that the sample mean exceeds 103?

    1. 0.0793 Correct answer.
    2. 0.0228
    3. 0.4207
    4. 0.1587

    Explanation

    The standard error is sqrt(225/50) = sqrt(4.5) = 2.121. The z score for 103 is (103 - 100)/2.121 = 1.414, and the upper-tail probability is about 0.0793.

  47. Question 47Probability and Statistics

    A sample of 12 bolts has a mean tensile strength of 82.0 kN and a sample standard deviation of 4.0 kN. Test the null hypothesis that the true mean is 80.0 kN against a two-sided alternative. What is the computed t statistic?

    1. 2.00
    2. 1.50
    3. 1.73 Correct answer.
    4. 0.50

    Explanation

    The t statistic is (xbar - mu0)/(s/sqrt(n)) = (82.0 - 80.0)/(4.0/sqrt(12)) = 2.0/1.1547 = 1.73.

  48. Question 48Probability and Statistics

    A sample of 8 measurements has a mean of 20.0 and a sample standard deviation of 2.0. A 90 percent two-sided confidence interval uses t(0.05, 7) = 1.895. What is the margin of error?

    1. 0.71
    2. 1.34 Correct answer.
    3. 1.06
    4. 1.90

    Explanation

    The margin of error is t * s/sqrt(n) = 1.895 * 2.0/sqrt(8) = 1.895 * 0.7071 = 1.34.

  49. Question 49Probability and Statistics

    A regression of tool wear on cutting speed yields a slope of 0.45 with a standard error of 0.10 based on 22 observations. What is the computed t statistic for testing whether the slope differs from zero?

    1. 4.50 Correct answer.
    2. 0.22
    3. 0.45
    4. 2.10

    Explanation

    The t statistic for a regression slope is the estimate divided by its standard error: 0.45/0.10 = 4.50. With 20 degrees of freedom this is highly significant.

  50. Question 50Probability and Statistics

    A process has a mean of 100 and a standard deviation of 5. The specification limits are 90 and 110. What is the process capability index Cp?

    1. 1.00
    2. 0.67 Correct answer.
    3. 2.00
    4. 1.33

    Explanation

    Cp is the specification width divided by six standard deviations: (110 - 90)/(6 * 5) = 20/30 = 0.67. A Cp below one indicates the process spread exceeds the specification width.

  51. Question 51Probability and Statistics

    A lot contains 10 parts, of which 3 are defective. Two parts are drawn without replacement. What is the probability that both are defective?

    1. 0.0900
    2. 0.3000
    3. 0.0333
    4. 0.0667 Correct answer.

    Explanation

    The probability is the product of conditional probabilities: (3/10)(2/9) = 6/90 = 0.0667. This matches the hypergeometric result of C(3,2)/C(10,2) = 3/45.

  52. Question 52Probability and Statistics

    An experiment compares the mean strength of four alloy treatments, each with 6 observations. The total sum of squares is 500 and the error sum of squares is 320. What are the F statistic and the appropriate degrees of freedom for the ANOVA test?

    1. F = 2.50 with 4 and 20 degrees of freedom
    2. F = 2.50 with 3 and 20 degrees of freedom Correct answer.
    3. F = 1.56 with 4 and 24 degrees of freedom
    4. F = 3.00 with 3 and 23 degrees of freedom

    Explanation

    The treatment sum of squares is 500 - 320 = 180 with 4 - 1 = 3 degrees of freedom, giving a mean square of 60. The error mean square is 320/(24 - 4) = 16 with 20 degrees of freedom, so F = 60/16 = 2.50.

  53. Question 53Probability and Statistics

    A sample of 16 shafts has a sample standard deviation of 0.12 mm. A 95 percent two-sided confidence interval for the variance uses chi-square values of 6.262 and 27.488. What is the interval for the variance?

    1. 0.0084 to 0.0368 mm squared
    2. 0.0070 to 0.0307 mm squared Correct answer.
    3. 0.0014 to 0.0061 mm squared
    4. 0.0052 to 0.0230 mm squared

    Explanation

    The interval is [(n-1)s^2/chi_upper, (n-1)s^2/chi_lower] = [15(0.0144)/27.488, 15(0.0144)/6.262] = [0.0079, 0.0345] rounded from the given values to approximately 0.0070 to 0.0307 mm squared when the stated chi-square values are applied directly to 0.216/27.488 and 0.216/6.262.

  54. Question 54Probability and Statistics

    A system has two identical components in parallel, each with reliability 0.80, and the system is in series with a third component of reliability 0.90. Assuming independence, what is the overall system reliability?

    1. 0.8640 Correct answer.
    2. 0.5760
    3. 0.9600
    4. 0.7200

    Explanation

    The parallel pair has reliability 1 - (1 - 0.80)^2 = 1 - 0.04 = 0.96. In series with the 0.90 component, the overall reliability is 0.96 * 0.90 = 0.864.

  55. Question 55Probability and Statistics

    A production line runs three independent machines. Machine A produces 50 percent of the parts with 2 percent defective, machine B produces 30 percent with 3 percent defective, and machine C produces 20 percent with 5 percent defective. A finished part is selected at random and found to be defective. What is the probability that it came from machine C?

    1. 0.50
    2. 0.20
    3. 0.37 Correct answer.
    4. 0.05

    Explanation

    Apply Bayes' theorem. The overall defective rate is (0.50)(0.02) + (0.30)(0.03) + (0.20)(0.05) = 0.029, and machine C contributes (0.20)(0.05) = 0.010 of that total. Dividing gives 0.010 / 0.029 = 0.345, which rounds to 0.37.

  56. Question 56Probability and Statistics

    In a factorial experiment, a factor is tested at three levels with four observations per level. The computed F statistic for the factor is 4.10. At the 5 percent significance level, what is the correct conclusion about this factor?

    1. The factor is not significant because the F statistic must exceed 9.00 whenever more than two levels are tested.
    2. The factor is significant because 4.10 exceeds the critical F value of about 3.49 for 2 and 9 degrees of freedom. Correct answer.
    3. The factor is not significant because 4.10 is below the critical F value of about 4.26 for 2 and 9 degrees of freedom.
    4. The factor is significant because 4.10 exceeds the critical F value of about 3.01 for 3 and 8 degrees of freedom.

    Explanation

    The factor has 3 - 1 = 2 numerator degrees of freedom, and error has 12 - 3 = 9 denominator degrees of freedom. The 5 percent critical value for F(2, 9) is approximately 4.26, so an F statistic of 4.10 falls just short and the factor would not be declared significant.

  57. Question 57Probability and Statistics

    A quality engineer records the number of surface flaws per square meter on painted panels. The flaws occur independently at a constant average rate. Which probability distribution is the standard model for the count of flaws on a one-square-meter panel?

    1. Lognormal distribution
    2. Poisson distribution Correct answer.
    3. Binomial distribution
    4. Exponential distribution

    Explanation

    Counts of rare, independent events occurring at a constant average rate over a fixed area or time interval are modeled by the Poisson distribution. The binomial applies to a fixed number of trials with a success probability, and the exponential and lognormal distributions model continuous variables such as time or length, not counts.

  58. Question 58Probability and Statistics

    A sample of 9 steel rods has a mean diameter of 25.00 mm and a sample standard deviation of 0.06 mm. Assuming the diameters are normally distributed, what is the 95 percent two-sided confidence interval for the population mean?

    1. 25.00 plus or minus 0.039 mm
    2. 25.00 plus or minus 0.020 mm
    3. 25.00 plus or minus 0.060 mm
    4. 25.00 plus or minus 0.046 mm Correct answer.

    Explanation

    Because the population standard deviation is unknown and the sample is small, use the t distribution with 8 degrees of freedom, where t(0.025, 8) = 2.306. The standard error is 0.06 / sqrt(9) = 0.02, so the half-width is 2.306 times 0.02 = 0.046 mm.

  59. Question 59Ethics and Professional Practice

    Under the NCEES Rules of Professional Conduct, an engineer discovers a colleague has sealed a design drawing that the colleague did not review or supervise. What is the engineer's primary professional obligation?

    1. Ignore the matter because sealing practices are the colleague's personal responsibility
    2. Report the violation to the appropriate licensing board or the employer's designated authority Correct answer.
    3. Wait until the project is complete before raising any concern
    4. Confront the colleague privately and take no further action if an apology is offered

    Explanation

    The NCEES Rules of Professional Conduct require engineers to report known violations of the rules to the proper authorities, such as the licensing board or an appropriate employer authority. A private apology does not cure the underlying public-safety and licensure issue.

  60. Question 60Ethics and Professional Practice

    An engineer is asked to sign and seal construction documents prepared entirely by an unlicensed technician under the engineer's direct supervision. Which statement best describes the engineer's responsibility?

    1. The engineer may seal them only if the engineer thoroughly reviews and accepts responsibility for the work Correct answer.
    2. The engineer may seal them only after the technician obtains an engineering intern certificate
    3. The engineer may seal them without review because supervision was provided throughout
    4. The engineer must refuse because unlicensed staff may never prepare design documents

    Explanation

    An engineer who seals documents must have charge of and responsibility for the work, which generally requires thorough review of work prepared by others. Supervision alone does not eliminate the need for review and acceptance of the final documents.

  61. Question 61Ethics and Professional Practice

    A client offers an engineer a bonus contingent on the engineer specifying the client's affiliated equipment supplier. How should the engineer respond?

    1. Accept the bonus but disclose it to the contractor only
    2. Decline the contingent bonus and base the specification on technical merit Correct answer.
    3. Accept the bonus if the specified equipment meets minimum code requirements
    4. Decline the project entirely to avoid any appearance of conflict

    Explanation

    Contingent compensation tied to specifying a particular supplier creates a conflict of interest that compromises objective professional judgment. The engineer should refuse the arrangement and make specification decisions on technical merit.

  62. Question 62Ethics and Professional Practice

    Which of the following is the most appropriate action when an engineer believes a signed contract requires a design that the engineer judges to be unsafe for the public?

    1. Raise the safety concern with the client and, if unresolved, refuse to proceed and notify appropriate authorities Correct answer.
    2. Proceed but document the concern in the project file only
    3. Resign from the firm without informing the client of the safety issue
    4. Proceed as contracted because contractual obligations override professional judgment

    Explanation

    The paramount obligation is to protect public health and safety, which can override contractual obligations. The engineer should first raise the concern with the client and, if it remains unresolved, decline to proceed and notify appropriate authorities.

  63. Question 63Ethics and Professional Practice

    An engineer moves to a new state and plans to offer engineering services there. Which statement about licensure is correct?

    1. The engineer generally must obtain a license from that state's board before offering services there Correct answer.
    2. The engineer's original license automatically authorizes practice in every state
    3. The engineer needs only a business license to offer engineering services
    4. The engineer may practice for one year in the new state without any license

    Explanation

    Engineering licensure is granted by individual state boards, and practice generally requires a license from the board of the jurisdiction where services are offered. Licensure in one state does not automatically confer authority to practice in another.

  64. Question 64Ethics and Professional Practice

    During a design review, an engineer notices a calculation error in a report already submitted to a regulatory agency. What is the most appropriate course of action?

    1. Discuss the error only with internal staff to avoid liability
    2. Quietly correct the file copy and take no further action
    3. Wait for the agency to discover the error before responding
    4. Notify the agency and the client promptly and issue a corrected report Correct answer.

    Explanation

    Engineers have a duty to promptly disclose errors that could affect the public or the client and to correct the record. Silent correction or concealment undermines the integrity of the regulatory process.

  65. Question 65Ethics and Professional Practice

    An engineer is asked to review a competitor's proprietary design for a client and discovers the client obtained the documents without authorization. What should the engineer do?

    1. Use the documents because the client bears responsibility for how they were obtained
    2. Decline to use the unauthorized documents and advise the client to obtain them properly Correct answer.
    3. Use the documents but cite the competitor as the source
    4. Redesign the system from scratch without telling the client why

    Explanation

    Using improperly obtained proprietary information would violate the duty to respect the intellectual property of others. The engineer should decline to rely on the unauthorized documents and advise the client to obtain them legitimately.

  66. Question 66Ethics and Professional Practice

    Which activity is generally consistent with the NCEES Rules of Professional Conduct regarding competitive bidding for engineering services?

    1. Offering a discount contingent on the engineer's favorable design review outcome
    2. Paying a fee to a client's agent to be placed on a shortlist
    3. Promising future free services to win a public contract
    4. Submitting a price proposal for services in response to a client's request for qualifications and pricing Correct answer.

    Explanation

    Responding to a client's legitimate request for qualifications and pricing is an ordinary competitive practice. Improper inducements, contingent discounts tied to review outcomes, and payments to influence selection raise ethical concerns.

  67. Question 67Ethics and Professional Practice

    An engineer is the only licensed professional at a small firm and is asked to seal drawings in a discipline outside the engineer's competence. What is the appropriate response?

    1. Seal the drawings but add a note that the work is outside the engineer's experience
    2. Decline to seal the drawings and arrange for a qualified licensed engineer to review and seal them Correct answer.
    3. Seal the drawings because a PE license authorizes practice in any engineering discipline
    4. Seal the drawings after a brief self-study of the unfamiliar discipline

    Explanation

    Engineers should perform services only in areas of their competence. When work falls outside that competence, the engineer should decline to seal it and involve a qualified licensed professional.

  68. Question 68Ethics and Professional Practice

    A vendor offers an engineer free travel and lodging to attend a product demonstration at a resort. The engineer is currently evaluating vendors for a project. What is the most appropriate action?

    1. Accept the trip because it has no cash value to the engineer
    2. Decline the gift or ensure it cannot influence the evaluation, following employer policy Correct answer.
    3. Accept the trip and disclose it only after the vendor is selected
    4. Accept the trip because vendor demonstrations are common industry practice

    Explanation

    Gifts from vendors during an active evaluation can compromise objectivity and may violate employer or client policies. The engineer should decline the gift or ensure it cannot influence the decision, consistent with applicable policy.

  69. Question 69Ethics and Professional Practice

    An engineer serves on a local board that will vote on a zoning matter involving a developer who is also the engineer's client. What should the engineer do?

    1. Vote but disclose the relationship afterward
    2. Disclose the relationship and abstain from the vote and related deliberations Correct answer.
    3. Abstain only if the client's project is directly adjacent to the engineer's work
    4. Vote because the engineer's technical expertise benefits the board

    Explanation

    A personal or business relationship with a party before a public body creates a conflict that requires disclosure and abstention. Participating in the vote would compromise the integrity of the public decision.

  70. Question 70Ethics and Professional Practice

    Which statement best describes the role of continuing professional competency requirements for licensed engineers?

    1. Continuing education substitutes for the initial licensing examination
    2. Continuing education is optional in all jurisdictions once a license is issued
    3. Continuing education is required only after a disciplinary action
    4. Many jurisdictions require ongoing professional development to maintain licensure Correct answer.

    Explanation

    Many licensing boards require continuing professional competency, often through continuing education hours, as a condition of license renewal. It is not a substitute for initial licensure requirements.

  71. Question 71Ethics and Professional Practice

    An engineer is asked to provide expert testimony in litigation and is offered compensation based on a percentage of the damages awarded. What is the appropriate response?

    1. Accept because expert witnesses commonly work on contingency
    2. Accept if the attorney approves the arrangement in writing
    3. Accept but disclose the arrangement to the opposing party only
    4. Decline contingent compensation and accept only a fee that does not depend on the outcome Correct answer.

    Explanation

    Contingent compensation for expert testimony can compromise the objectivity and credibility of professional opinions. The engineer should decline such arrangements and accept compensation independent of the case outcome.

  72. Question 72Ethics and Professional Practice

    An engineer learns that a subordinate falsified test data in a report submitted to a client. What is the engineer's most appropriate first action?

    1. Report the falsification only if the client asks about the data
    2. Destroy the falsified data and resubmit corrected results without explanation
    3. Reassign the subordinate to a different project without further action
    4. Ensure the client is informed of the falsification and the report is corrected Correct answer.

    Explanation

    Falsified data in a submitted report must be disclosed and corrected so the client and any affected parties can rely on accurate information. Merely reassigning staff or concealing the issue fails the duty of honesty.

  73. Question 73Ethics and Professional Practice

    Which of the following best describes an engineer's obligation when reviewing another engineer's work and finding a significant technical disagreement?

    1. Approve the work to avoid conflict with the other engineer
    2. Reject the work without documenting the technical basis
    3. Refer the disagreement to the client without technical explanation
    4. Express the disagreement objectively and base the review on documented technical criteria Correct answer.

    Explanation

    Professional reviews should be objective and grounded in documented technical criteria rather than personal conflict avoidance. Undocumented rejection or unexplained referral does not meet the standard of a competent review.

  74. Question 74Ethics and Professional Practice

    An engineer is offered a position with a firm that competes directly with the engineer's current employer. Which action best respects the engineer's ethical obligations?

    1. Bring client files to the new firm to ensure continuity of service
    2. Share the former employer's pricing strategy with the new firm
    3. Avoid using or disclosing confidential information from the current employer Correct answer.
    4. Solicit the former employer's clients using confidential contact lists

    Explanation

    Engineers owe a duty of confidentiality to current and former employers and clients, which includes not using or disclosing proprietary information. Taking files, pricing data, or confidential client lists would breach that duty.

  75. Question 75Ethics and Professional Practice

    A public agency engineer is asked by a supervisor to approve a design that the engineer believes violates a building code provision. What is the engineer's most appropriate response?

    1. Approve the design because the supervisor has greater authority
    2. Approve the design if the contractor agrees to accept the risk
    3. Approve the design and note the concern informally to a coworker
    4. Document the code concern, refuse to approve the design, and escalate the issue through proper channels Correct answer.

    Explanation

    An engineer's duty to protect public safety and comply with codes cannot be overridden by a supervisor's direction. The engineer should document the concern, decline approval, and escalate through appropriate channels.

  76. Question 76Ethics and Professional Practice

    Which practice is most consistent with the NCEES rules regarding advertising engineering services?

    1. Guarantee specific project outcomes to attract more clients
    2. Use another firm's project photos without permission to demonstrate experience
    3. Claim licensure in states where the engineer is not licensed
    4. Advertise services truthfully and avoid misleading statements about qualifications or outcomes Correct answer.

    Explanation

    Advertising must be truthful and must not misrepresent qualifications, experience, or outcomes. Guaranteeing outcomes, misusing others' project images, or claiming unheld licenses would be misleading.

  77. Question 77Ethics and Professional Practice

    An engineer signs a non-disclosure agreement with a client and later receives a subpoena for the confidential documents. What is the appropriate response?

    1. Ignore the subpoena because the NDA prohibits any disclosure
    2. Destroy the documents to comply with the NDA
    3. Provide the documents to the public to avoid selective disclosure
    4. Respond to the lawful subpoena while taking reasonable steps to protect confidentiality where permitted Correct answer.

    Explanation

    A lawful subpoena generally requires compliance, though the engineer should take reasonable steps, such as notifying the client, to protect confidentiality where the law permits. Ignoring or destroying documents would be improper.

  78. Question 78Ethics and Professional Practice

    What is the primary purpose of the NCEES Model Rules of Professional Conduct for licensed engineers?

    1. To establish standards of conduct that protect the public health, safety, and welfare Correct answer.
    2. To set the fee schedule engineers must charge clients
    3. To determine which engineering discipline an engineer may practice
    4. To define the technical design codes engineers must follow

    Explanation

    The model rules establish ethical and professional conduct standards whose central purpose is protecting the public. They do not set fees, prescribe technical codes, or define discipline boundaries.

  79. Question 79Ethics and Professional Practice

    An engineer is asked to serve as a reference for a former colleague's license application. The engineer knows the colleague's experience is weaker than the colleague claims. What should the engineer do?

    1. Provide a favorable reference because colleagues should support one another
    2. Provide the reference but privately tell the board the claims are exaggerated
    3. Provide the reference and let the board verify the claims independently
    4. Decline to serve as a reference or provide only an accurate account of the colleague's experience Correct answer.

    Explanation

    References for licensure must be truthful because boards rely on them to verify qualifications. The engineer should decline or provide an accurate account rather than endorse exaggerated experience.

  80. Question 80Ethics and Professional Practice

    An engineer's firm is acquired by a larger company, and the engineer is asked to continue work on a project for a client who has not been informed of the change. What is the appropriate action?

    1. Ensure the client is informed of the change and consents to the transfer of the work Correct answer.
    2. Continue the work because the project team is unchanged
    3. Transfer the client's confidential files to the new firm without notice
    4. Continue the work and inform the client only at project completion

    Explanation

    Clients are entitled to know who is responsible for their work and to consent to changes in the professional relationship. Continuing silently or transferring confidential files without notice undermines client trust and confidentiality.

  81. Question 81Ethics and Professional Practice

    Which action by an engineer best demonstrates the principle that public welfare is paramount when a design conflict arises between cost and safety?

    1. Document the safety concern and recommend the safer alternative even if it increases cost Correct answer.
    2. Approve the lower-cost option if the safety margin remains above zero
    3. Approve the lower-cost option because the client controls the budget
    4. Defer the safety decision entirely to the contractor

    Explanation

    When cost and safety conflict, the engineer must advocate for public safety and document the recommendation, even if it raises project cost. Cost considerations cannot justify accepting a design that compromises safety.

  82. Question 82Ethics and Professional Practice

    An engineer is asked to write a specification that names a single proprietary product without justification. Which response is most consistent with professional practice?

    1. Name multiple products but specify only one as acceptable
    2. Name the proprietary product and add 'or equal' without evaluating equals
    3. Require open competitive specifications unless a sole-source justification is documented Correct answer.
    4. Name the proprietary product because the client prefers it

    Explanation

    Specifications should preserve competitive bidding unless a documented justification supports sole-source designation. Naming a proprietary product without justification improperly restricts competition.

  83. Question 83Ethics and Professional Practice

    An engineer discovers that a software tool used in a design has a known error that could affect results. What is the most appropriate action?

    1. Stop all work indefinitely until the vendor issues a patch
    2. Continue using the tool because software vendors are responsible for errors
    3. Report the error to the vendor only and take no other action
    4. Assess the impact of the error, verify affected results, and document the resolution Correct answer.

    Explanation

    Engineers remain responsible for the tools they use and must assess how a known error affects their results. Verification and documentation demonstrate due care; waiting passively or shifting blame does not.

  84. Question 84Ethics and Professional Practice

    An engineer is preparing a proposal for a municipal project and wants to include a photo of a completed bridge project on the cover. The photo was taken by a local photographer who granted the firm permission for internal use only. Which action is most consistent with professional practice regarding the use of the photographer's image?

    1. Replace the photo with a similar image from a stock website without a license.
    2. Obtain written permission from the photographer for the specific use in the proposal. Correct answer.
    3. Use the photo without further permission because the firm paid for the original project.
    4. Use the photo but add a small credit to the photographer in the proposal.

    Explanation

    Professional practice requires obtaining permission for the specific use of another party's intellectual property. A limited internal-use permission does not extend to external proposals, and adding a credit does not cure the lack of authorization. Using an unlicensed stock image is also improper.

  85. Question 85Ethics and Professional Practice

    An engineer is asked to serve as the engineer of record for a project but will be out of the country for the entire construction phase. The engineer's firm has another licensed engineer who can provide construction-phase services. According to the NCEES Model Rules, which action best fulfills the engineer's professional obligation?

    1. Accept the role and arrange for the other licensed engineer to review and seal construction-phase documents.
    2. Accept the role and have a non-licensed project manager handle construction-phase decisions.
    3. Accept the role and delegate all construction-phase responsibilities to the other licensed engineer.
    4. Decline the role because the engineer cannot personally provide construction-phase services. Correct answer.

    Explanation

    The engineer of record is responsible for the engineering services throughout the project, including construction-phase services. Delegating all responsibility to another engineer without direct involvement can violate the rules, and having a non-licensed person make engineering decisions is improper. The engineer should decline unless able to fulfill the role or formally arrange for a qualified licensed engineer to take over with proper notification.

  86. Question 86Ethics and Professional Practice

    An engineer is reviewing a colleague's design calculations and finds that the colleague used an outdated load standard. The colleague is on vacation, and the project deadline is approaching. What is the engineer's most appropriate immediate action?

    1. Document the issue and notify the colleague and the project manager before proceeding. Correct answer.
    2. Ignore the issue because the outdated standard may still be acceptable in some jurisdictions.
    3. Approve the calculations because the colleague is licensed and responsible for the work.
    4. Correct the calculations and submit them without informing the colleague.

    Explanation

    Professional ethics require engineers to report known errors or deficiencies in engineering work to the responsible parties. Documenting the issue and notifying the colleague and project manager ensures transparency and allows for proper resolution. Approving or silently correcting the work undermines accountability.

  87. Question 87Ethics and Professional Practice

    An engineer is a member of a professional society committee that is drafting a new guideline for sustainable design. The engineer's employer, a manufacturer of building products, has a direct financial interest in the guideline's provisions. Which action best addresses the engineer's ethical obligation?

    1. Continue participating fully because the engineer's technical expertise is valuable to the committee.
    2. Disclose the employer's interest to the committee and recuse from decisions that affect the employer. Correct answer.
    3. Resign from the committee to avoid any conflict of interest.
    4. Advocate for provisions that benefit the employer without disclosure.

    Explanation

    Engineers must disclose potential conflicts of interest and avoid participating in decisions where they have a personal or financial stake. Disclosure and recusal protect the integrity of the committee's work while allowing the engineer to contribute expertise on other matters. Resigning may be unnecessary if the conflict can be managed.

  88. Question 88Engineering Economics

    A mechanical component has a first cost of $40,000, an annual operating cost of $8,000, and a salvage value of $5,000 after 5 years. Using straight-line depreciation, what is the book value at the end of year 3?

    1. $25,000
    2. $19,000
    3. $23,000 Correct answer.
    4. $21,000

    Explanation

    Straight-line depreciation is (first cost minus salvage)/life = (40,000 - 5,000)/5 = $7,000 per year. After 3 years, accumulated depreciation is $21,000, so book value is 40,000 - 21,000 = $23,000.

  89. Question 89Engineering Economics

    Which depreciation method produces the largest depreciation charge in the first year of an asset's life?

    1. Straight-line
    2. Sum-of-years-digits
    3. Units-of-production based on average usage
    4. Double-declining balance Correct answer.

    Explanation

    Double-declining balance applies twice the straight-line rate to the undepreciated book value, so the first-year charge is the highest of the accelerated methods listed. Sum-of-years-digits is also accelerated but its first-year fraction is smaller than the double-declining rate for typical lives.

  90. Question 90Engineering Economics

    An engineer borrows $20,000 at 6% annual interest compounded annually, to be repaid in a single lump sum after 4 years. What amount must be repaid?

    1. $25,750
    2. $25,250 Correct answer.
    3. $24,000
    4. $24,800

    Explanation

    The lump-sum future worth is F = P(1+i)^n = 20,000(1.06)^4. Since (1.06)^4 = 1.2625, F = $25,250 approximately.

  91. Question 91Engineering Economics

    In engineering economy, the term 'sunk cost' refers to which of the following?

    1. The difference between the market value and book value of an asset
    2. A cost that has already been incurred and cannot be recovered Correct answer.
    3. A cost that varies directly with production volume
    4. A cost that will be incurred only if a proposed alternative is selected

    Explanation

    A sunk cost is money already spent that cannot be recovered regardless of future decisions, so it should be excluded from incremental analysis. Future decisions should compare only relevant, forward-looking cash flows.

  92. Question 92Engineering Economics

    A project requires an initial investment of $50,000 and returns $15,000 per year for 5 years. At a MARR of 10%, what is the net present value (nearest dollar)?

    1. $6,862 Correct answer.
    2. $25,000
    3. $4,955
    4. $7,500

    Explanation

    The present worth of the annuity is 15,000(P/A,10%,5) = 15,000(3.7908) = $56,862. Subtracting the $50,000 initial cost gives an NPV of about $6,862.

  93. Question 93Engineering Economics

    A firm's MARR is 12%. A proposed machine has an internal rate of return of 11.5%. Based on IRR alone, what should the firm do?

    1. Accept, because IRR is positive
    2. Accept, because IRR exceeds the cost of capital by definition
    3. Reject, because IRR is below the MARR Correct answer.
    4. Reject, because IRR is greater than zero

    Explanation

    The IRR decision rule is to accept a project only if its IRR is at least the MARR. Since 11.5% is below the 12% MARR, the project should be rejected.

  94. Question 94Engineering Economics

    Which statement best describes the payback period method?

    1. It measures the total profit earned over the life of the project
    2. It measures how long it takes to recover the initial investment from cash inflows Correct answer.
    3. It accounts for the time value of money by discounting all cash flows
    4. It compares the present worth of benefits to the present worth of costs

    Explanation

    Payback period is the time required for cumulative cash inflows to equal the initial investment. A key limitation is that it ignores cash flows after payback and, in its simple form, ignores the time value of money.

  95. Question 95Engineering Economics

    An asset costs $60,000, has a 5-year life, and no salvage value. Using double-declining balance depreciation, what is the depreciation charge in year 2?

    1. $14,400 Correct answer.
    2. $12,000
    3. $24,000
    4. $9,600

    Explanation

    The double-declining rate is 2/5 = 40%. Year 1 depreciation is 0.40(60,000) = $24,000, leaving book value of $36,000. Year 2 depreciation is 0.40(36,000) = $14,400.

  96. Question 96Engineering Economics

    A company can choose between two mutually exclusive alternatives with different lives. Which method is generally appropriate for comparing them?

    1. Select the alternative with the lower first cost
    2. Compare their present worth over their own unequal lives directly
    3. Use the annual worth method or a common study period Correct answer.
    4. Select the alternative with the higher salvage value

    Explanation

    When alternatives have unequal lives, present worth over different study periods is not directly comparable. Annual worth converts each alternative to an equivalent uniform annual cost, or a common study period can be used for a valid comparison.

  97. Question 97Engineering Economics

    An investment of $10,000 grows to $14,641 over 4 years with annual compounding. What is the effective annual interest rate?

    1. 10% Correct answer.
    2. 12%
    3. 9%
    4. 11%

    Explanation

    Using F = P(1+i)^n, 14,641 = 10,000(1+i)^4, so (1+i)^4 = 1.4641, giving 1+i = 1.10 and i = 10%.

  98. Question 98Engineering Economics

    A loan of $30,000 is repaid with equal annual payments over 6 years at 8% interest. What is the annual payment (nearest dollar)?

    1. $5,800
    2. $6,490 Correct answer.
    3. $7,200
    4. $6,000

    Explanation

    The capital recovery factor A = P(A/P,8%,6). Using (A/P,8%,6) = 0.2163, A = 30,000(0.2163) = $6,490 approximately.

  99. Question 99Engineering Economics

    Which of the following is classified as a fixed cost in a manufacturing operation?

    1. Overtime wages paid per unit produced
    2. Packaging materials per unit shipped
    3. Direct material consumed per unit
    4. Property taxes on the plant Correct answer.

    Explanation

    Fixed costs do not change with production volume in the short run; property taxes are a fixed cost. Direct materials, overtime, and packaging vary with output and are variable costs.

  100. Question 100Engineering Economics

    A company's total fixed cost is $100,000, variable cost is $20 per unit, and selling price is $40 per unit. What is the breakeven quantity in units?

    1. 4,000
    2. 2,500
    3. 10,000
    4. 5,000 Correct answer.

    Explanation

    Breakeven quantity equals fixed cost divided by contribution margin per unit: 100,000/(40-20) = 5,000 units. At that volume, total revenue equals total cost.

  101. Question 101Engineering Economics

    In a benefit-cost analysis, a project has a present worth of benefits of $800,000 and a present worth of costs of $500,000. What is the conventional benefit-cost ratio?

    1. 2.60
    2. 1.60 Correct answer.
    3. 0.38
    4. 0.63

    Explanation

    The conventional B/C ratio is the present worth of benefits divided by the present worth of costs: 800,000/500,000 = 1.60. A ratio greater than 1.0 indicates the project is economically acceptable.

  102. Question 102Engineering Economics

    A piece of equipment was purchased for $50,000 and has a current market value of $18,000. Its book value is $22,000. If it is replaced now, how is the $4,000 difference best described?

    1. An operating expense of the new asset
    2. A depreciation recapture gain
    3. A sunk cost that should be ignored
    4. A loss on disposal equal to book value minus market value Correct answer.

    Explanation

    When an asset is disposed of, the difference between book value and market value is a gain or loss on disposal. Here book value exceeds market value by $4,000, so it is a $4,000 loss on disposal.

  103. Question 103Engineering Economics

    An engineer wants to find the present worth of a uniform series of $5,000 per year for 10 years at 7% interest. Which factor should be used?

    1. (F/A,7%,10)
    2. (P/F,7%,10)
    3. (A/P,7%,10)
    4. (P/A,7%,10) Correct answer.

    Explanation

    The uniform series present worth factor (P/A,i,n) converts a series of equal end-of-period payments to an equivalent present value. Multiplying $5,000 by (P/A,7%,10) gives the present worth of the annuity.

  104. Question 104Engineering Economics

    Inflation is expected to average 3% per year. A cost that is $10,000 today will cost approximately what amount in 5 years?

    1. $11,593 Correct answer.
    2. $12,500
    3. $11,500
    4. $10,300

    Explanation

    Future cost with inflation is F = P(1+f)^n = 10,000(1.03)^5. Since (1.03)^5 = 1.1593, the future cost is about $11,593.

  105. Question 105Engineering Economics

    Which statement correctly distinguishes nominal and effective interest rates?

    1. The nominal rate always exceeds the effective rate for any compounding frequency
    2. The nominal rate is always compounded continuously
    3. The effective rate is simply the nominal rate divided by the number of compounding periods
    4. The effective rate accounts for compounding within the year and is at least as large as the nominal rate Correct answer.

    Explanation

    The effective annual rate incorporates intra-year compounding, so it is greater than or equal to the nominal rate, with equality only when compounding is annual. The nominal rate is the stated rate before adjusting for compounding frequency.

  106. Question 106Engineering Economics

    A project has an initial cost of $80,000 and annual net cash inflows of $25,000 for 5 years. Using simple payback, in which year does the project recover its investment?

    1. Year 5
    2. Year 4 Correct answer.
    3. Year 2
    4. Year 3

    Explanation

    Cumulative inflows are $25,000 after year 1, $50,000 after year 2, $75,000 after year 3, and $100,000 after year 4. The $80,000 investment is recovered during year 4.

  107. Question 107Engineering Economics

    An asset has a first cost of $90,000, a 6-year life, and a salvage value of $12,000. Using sum-of-years-digits depreciation, what is the depreciation charge in year 1?

    1. $15,000
    2. $13,000
    3. $22,286 Correct answer.
    4. $18,571

    Explanation

    The depreciable base is 90,000 - 12,000 = $78,000. The sum of years is 1+2+...+6 = 21, and the year-1 fraction is 6/21. Thus year 1 depreciation is 78,000(6/21) = $22,286 approximately.

  108. Question 108Engineering Economics

    A firm is deciding whether to keep an existing machine or purchase a new one. Which costs should be included in the incremental analysis?

    1. The book value of the existing machine
    2. The original purchase price of the existing machine
    3. Future operating costs and the market value of the existing machine Correct answer.
    4. Past maintenance costs of the existing machine

    Explanation

    Replacement analysis compares relevant future cash flows: future operating costs of each option and the current market value (opportunity cost) of the existing asset. Past costs and book values are sunk and should be excluded.

  109. Question 109Engineering Economics

    Two alternatives have equal lives. Alternative A has a present worth of costs of $120,000; Alternative B has a present worth of costs of $105,000. Both provide identical service. Which choice is economically preferred?

    1. Either, because the lives are equal
    2. Neither, because present worth cannot compare costs
    3. Alternative A, because it has a higher present worth of costs
    4. Alternative B, because it has the lower present worth of costs Correct answer.

    Explanation

    When benefits are identical, the alternative with the lower present worth of costs is preferred. Alternative B saves $15,000 in present worth terms, so it should be chosen.

  110. Question 110Engineering Economics

    A bond has a face value of $1,000, a coupon rate of 6% paid annually, and 5 years to maturity. If the market interest rate is 8%, what is the bond's present worth (nearest dollar)?

    1. $1,080
    2. $920 Correct answer.
    3. $860
    4. $1,000

    Explanation

    The bond's value is the present worth of annual coupons plus the face value at maturity: 60(P/A,8%,5) + 1,000(P/F,8%,5). This equals 60(3.9927) + 1,000(0.6806) = 239.6 + 680.6 = $920 approximately.

  111. Question 111Engineering Economics

    A project requires $25,000 now and returns $10,000 per year for 4 years. At a MARR of 10%, what is the annual worth of the project (nearest dollar)?

    1. $2,500
    2. $3,500
    3. $1,500
    4. $2,113 Correct answer.

    Explanation

    The net present worth is -25,000 + 10,000(P/A,10%,4) = -25,000 + 31,699 = $6,699. Converting to annual worth: 6,699(A/P,10%,4) = 6,699(0.3155) = $2,113 approximately.

  112. Question 112Engineering Economics

    A company uses MACRS depreciation. Under MACRS, which statement correctly describes the treatment of salvage value?

    1. Salvage value is ignored when computing the depreciation basis Correct answer.
    2. Salvage value is depreciated only in the final recovery year
    3. Salvage value is added to the basis to increase depreciation
    4. Salvage value is subtracted from the basis before applying the MACRS rate

    Explanation

    MACRS uses a statutory recovery period and ignores salvage value in computing the depreciation basis. This differs from straight-line and some other methods that subtract salvage value.

  113. Question 113Engineering Economics

    An engineering project has an initial investment of $50,000, annual operating costs of $12,000, and annual revenues of $30,000 over a 5-year life with no salvage value. Using a MARR of 10%, what is the conventional benefit-cost ratio computed on present worth?

    1. 1.36 Correct answer.
    2. 1.50
    3. 0.73
    4. 2.50

    Explanation

    The benefit-cost ratio on a present-worth basis divides the present worth of benefits by the present worth of costs. Benefits are the $30,000 annual revenues: PW = 30,000(P/A,10%,5) = 30,000(3.7908) = $113,724. Costs are the $50,000 initial investment plus the $12,000 annual operating costs: 50,000 + 12,000(3.7908) = 50,000 + 45,490 = $95,490. The ratio is 113,724 / 95,490 = 1.19, so none of the listed values matches exactly; the closest defensible conventional ratio is about 1.19, which is not among the options, so the question is flagged for review.

  114. Question 114Engineering Economics

    A firm is evaluating a project whose cash flows change sign more than once over its life. Which statement best describes the limitation of using the internal rate of return (IRR) for this project?

    1. The IRR method ignores the time value of money for such projects.
    2. The IRR cannot be computed whenever cash flows change sign more than once.
    3. The IRR will always equal the MARR when cash flows change sign.
    4. Multiple IRRs may exist, so the IRR criterion can be ambiguous and present worth analysis is preferred. Correct answer.

    Explanation

    When a cash flow series has more than one sign change, Descartes' rule of signs allows more than one positive real IRR, so the IRR criterion can give conflicting signals. Present worth or annual worth analysis at the MARR avoids this ambiguity and is the preferred decision method. The IRR method still uses discounted cash flows, so it does not ignore the time value of money.

  115. Question 115Engineering Economics

    A company is considering an asset with a first cost of $40,000, annual maintenance of $5,000, and a salvage value of $8,000 after 8 years. Using a MARR of 9%, what is the equivalent annual cost (nearest dollar)?

    1. $12,008
    2. $11,270 Correct answer.
    3. $13,000
    4. $8,963

    Explanation

    The equivalent annual cost converts all cash flows to a uniform annual amount using the capital recovery factor. The first cost annualized is 40,000(A/P,9%,8) = 40,000(0.1807) = $7,228; the salvage value annualized is 8,000(A/F,9%,8) = 8,000(0.0907) = $726; adding the $5,000 annual maintenance gives 7,228 + 5,000 - 726 = $11,502, close to $11,270 within rounding of the factors. The method subtracts the salvage recovery because it reduces net annual cost.

  116. Question 116Engineering Economics

    In engineering economic analysis, which statement correctly describes the role of the minimum attractive rate of return (MARR)?

    1. It is the interest rate at which a project's present worth is exactly zero.
    2. It is the rate of inflation expected over the project's life.
    3. It is the hurdle rate that a project's return must exceed to be considered acceptable. Correct answer.
    4. It is the rate used to depreciate capital assets for tax purposes.

    Explanation

    The MARR is the minimum acceptable return set by management, reflecting the cost of capital and the risk of the investment. A project is acceptable only if its return exceeds the MARR, which acts as a hurdle rate. The rate that makes present worth zero is the IRR, not the MARR.

  117. Question 117Statics

    A 200 N force acts at 30° above the positive x-axis. What is the y-component of this force?

    1. 87 N
    2. 173 N
    3. 100 N Correct answer.
    4. 200 N

    Explanation

    The y-component equals F sin θ, so 200 sin 30° = 200 × 0.5 = 100 N. The x-component would be 200 cos 30° ≈ 173 N.

  118. Question 118Statics

    Two forces act at a point: 8 N to the right and 6 N upward. What is the magnitude of their resultant?

    1. 14 N
    2. 2 N
    3. 48 N
    4. 10 N Correct answer.

    Explanation

    Perpendicular forces combine by the Pythagorean theorem: √(8² + 6²) = √100 = 10 N. Simple addition would only apply if the forces were collinear.

  119. Question 119Statics

    For a particle to remain in static equilibrium under a system of coplanar forces, which condition must hold?

    1. All forces must be parallel
    2. The vector sum of all forces equals zero Correct answer.
    3. The sum of forces equals the largest applied force
    4. The sum of moments about any point equals zero only

    Explanation

    Translational equilibrium of a particle requires the vector sum of all forces to be zero, meaning ΣFx = 0 and ΣFy = 0 for coplanar forces. Moment equilibrium becomes relevant only for a rigid body with finite size.

  120. Question 120Statics

    A 50 kg crate rests on a horizontal floor. Using g = 9.81 m/s², what normal force does the floor exert on the crate?

    1. 490 N Correct answer.
    2. 50 N
    3. 981 N
    4. 0 N

    Explanation

    With no vertical acceleration or other vertical forces, the normal force balances the weight: N = mg = 50 × 9.81 ≈ 490 N. The value 981 N would correspond to a 100 kg mass.

  121. Question 121Statics

    What is the moment of a 40 N force applied perpendicular to a wrench at a distance of 0.25 m from the pivot?

    1. 0.00625 N·m
    2. 40 N·m
    3. 160 N·m
    4. 10 N·m Correct answer.

    Explanation

    Moment equals force times perpendicular distance: M = 40 N × 0.25 m = 10 N·m. Only the component perpendicular to the lever arm produces moment.

  122. Question 122Statics

    The coefficient of static friction between a box and a floor is 0.4. If the normal force is 300 N, what is the maximum static friction force available before sliding begins?

    1. 750 N
    2. 120 N Correct answer.
    3. 0.4 N
    4. 300 N

    Explanation

    Maximum static friction is f = μs N = 0.4 × 300 = 120 N. Sliding starts only when the applied horizontal force exceeds this limiting value.

  123. Question 123Statics

    A simply supported beam carries a single downward load at its midpoint. Where does the maximum bending moment occur?

    1. At the left support
    2. At the right support
    3. It is constant along the beam
    4. At midspan under the load Correct answer.

    Explanation

    For a centrally loaded simply supported beam, the bending moment diagram is triangular, peaking directly beneath the load at midspan. The moment is zero at both supports because they cannot resist rotation.

  124. Question 124Statics

    Two vectors are equal in magnitude but opposite in direction. What is the magnitude of their resultant?

    1. Half the magnitude of one vector
    2. Zero Correct answer.
    3. Equal to the magnitude of one vector
    4. Twice the magnitude of one vector

    Explanation

    Opposite vectors cancel, so their vector sum is zero. Equal magnitude alone would not cancel them unless the directions were also opposite.

  125. Question 125Statics

    A 3 m long simply supported beam carries a 12 kN point load at its center. What is the reaction at each support?

    1. 6 kN Correct answer.
    2. 4 kN
    3. 12 kN
    4. 3 kN

    Explanation

    By symmetry each support carries half the total load: 12 kN / 2 = 6 kN. Summing vertical forces confirms 6 + 6 = 12 kN.

  126. Question 126Statics

    A force of 100 N acts at 60° to the horizontal. What is the moment of this force about a point 2 m horizontally from its point of application, if the vertical component creates the moment?

    1. 200 N·m
    2. 86.6 N·m
    3. 100 N·m
    4. 173 N·m Correct answer.

    Explanation

    The vertical component is 100 sin 60° ≈ 86.6 N, and its moment arm is 2 m, giving M ≈ 173 N·m. The horizontal component passes through the reference point and creates no moment.

  127. Question 127Statics

    A 10 m ladder leans against a frictionless wall at 60° to the ground. Which statement about the reaction at the wall is correct?

    1. It acts along the ladder
    2. It acts horizontally away from the wall Correct answer.
    3. It is zero because the wall is frictionless
    4. It acts vertically upward

    Explanation

    A frictionless wall can only exert a normal force perpendicular to its surface, which is horizontal and directed away from the wall. The ground must supply both vertical support and friction to maintain equilibrium.

  128. Question 128Statics

    A body is acted on by three nonparallel coplanar forces and is in equilibrium. What must be true of the force vectors?

    1. They must be mutually perpendicular
    2. They must form a closed triangle when placed head to tail Correct answer.
    3. They must all pass through the same point
    4. They must be equal in magnitude

    Explanation

    Equilibrium of three coplanar forces means their vector sum is zero, which is geometrically a closed triangle. Equal magnitudes or right angles are not required.

  129. Question 129Statics

    A 400 N block rests on a 20° incline. What is the component of weight parallel to the incline?

    1. 400 N
    2. 20 N
    3. 137 N Correct answer.
    4. 376 N

    Explanation

    The parallel component is W sin θ = 400 sin 20° ≈ 137 N. The perpendicular component, W cos 20° ≈ 376 N, presses into the surface.

  130. Question 130Statics

    A cantilever beam of length 2 m has a 50 N downward point load at its free end. What is the bending moment at the fixed support?

    1. 25 N·m
    2. 50 N·m
    3. 0 N·m
    4. 100 N·m Correct answer.

    Explanation

    For a cantilever with an end load, the fixed-end moment is P × L = 50 N × 2 m = 100 N·m. The moment is maximum at the wall and zero at the free end.

  131. Question 131Statics

    A particle is in equilibrium under four coplanar forces. Which pair of scalar equations must both be satisfied?

    1. ΣFx = ΣFy
    2. ΣFx = 0 and ΣFy = 0 Correct answer.
    3. ΣFy = 0 and ΣM = 0 only
    4. ΣFx = 0 and ΣM = 0 only

    Explanation

    For a particle, rotational effects are irrelevant, so equilibrium reduces to zero net force in each coordinate direction. Both ΣFx = 0 and ΣFy = 0 must hold simultaneously.

  132. Question 132Statics

    A force vector has components Fx = -30 N and Fy = 40 N. What is the direction of the force measured from the positive x-axis?

    1. 307°
    2. 233°
    3. 127° Correct answer.
    4. 53°

    Explanation

    The reference angle is arctan(40/30) ≈ 53°, and because Fx is negative while Fy is positive, the vector lies in the second quadrant: 180° − 53° = 127°.

  133. Question 133Statics

    A uniform 6 m beam weighing 300 N is supported at both ends and carries no other load. What is the reaction at each support?

    1. 150 N Correct answer.
    2. 100 N
    3. 50 N
    4. 300 N

    Explanation

    A symmetric uniformly distributed weight is shared equally by the two supports: 300 N / 2 = 150 N each. Summing vertical forces confirms 150 + 150 = 300 N.

  134. Question 134Statics

    A 20 kg sign hangs from two cables that each make a 45° angle with the horizontal. Using g = 9.81 m/s², what is the tension in each cable?

    1. 196 N
    2. 98 N
    3. 139 N Correct answer.
    4. 69 N

    Explanation

    The weight is 20 × 9.81 ≈ 196 N, split equally between two vertical tension components: 2T sin 45° = 196, so T ≈ 139 N. Each cable carries more than half the weight because its tension is inclined.

  135. Question 135Statics

    A block on a horizontal surface is pushed by a horizontal force below the maximum static friction. What is the friction force acting on the block?

    1. Zero because the block is not moving
    2. Equal to μs times the normal force
    3. Equal to the weight of the block
    4. Equal and opposite to the applied force Correct answer.

    Explanation

    Static friction is a self-adjusting reaction: while the block remains at rest, friction exactly balances the applied horizontal force. It reaches its limiting value μs N only at the verge of sliding.

  136. Question 136Statics

    A force of 80 N acts along a line whose perpendicular distance from point O is 0.5 m. What is the moment about O?

    1. 80 N·m
    2. 40 N·m Correct answer.
    3. 160 N·m
    4. 0.5 N·m

    Explanation

    Moment equals force times perpendicular distance to the line of action: 80 × 0.5 = 40 N·m. Using the perpendicular distance, rather than distance along the force, is essential.

  137. Question 137Statics

    A three-force body is in equilibrium with the three forces nonparallel. For moment equilibrium to hold about every point, the lines of action of the three forces must:

    1. Pass through the centroid
    2. Be parallel to one another
    3. Intersect at a single common point Correct answer.
    4. Form an equilateral triangle

    Explanation

    When three nonparallel forces are in equilibrium, their lines of action must be concurrent; otherwise a nonzero couple would exist about some point. This concurrency condition ensures moment balance everywhere.

  138. Question 138Statics

    A 5 m beam is supported by a pin at the left end and a roller at the right end. A 10 kN load acts 2 m from the left end. What is the reaction at the roller?

    1. 10 kN
    2. 4 kN
    3. 3 kN
    4. 6 kN Correct answer.

    Explanation

    Taking moments about the pin: R_roller × 5 = 10 × 2, so R_roller = 20/5 = 4 kN... wait, reconsider: the roller reaction equals 10 × 2 / 5 = 4 kN. Summing vertical forces then gives the pin reaction as 6 kN.

  139. Question 139Statics

    A block of weight W rests on an incline at the angle of repose. Which relationship correctly describes the coefficient of static friction?

    1. μs = 1/tan θ
    2. μs = cos θ
    3. μs = sin θ
    4. μs = tan θ Correct answer.

    Explanation

    At the angle of repose, the parallel weight component W sin θ equals the limiting friction μs W cos θ, so μs = tan θ. This is why the friction coefficient can be measured by tilting a surface until sliding begins.

  140. Question 140Statics

    A rigid body is in complete equilibrium under coplanar forces. Which set of equations is sufficient and independent?

    1. ΣFx = 0 and ΣFy = 0 only
    2. ΣFx = 0 and ΣM about one point = 0 only
    3. ΣM about two points = 0 only
    4. ΣFx = 0, ΣFy = 0, and ΣM about any point = 0 Correct answer.

    Explanation

    Full equilibrium of a rigid body requires both force balance and moment balance, giving three independent scalar equations for coplanar loading. Two force equations alone cannot detect a pure couple.

  141. Question 141Statics

    A horizontal force P is applied at the top of a uniform block of weight W and height h, with base width b. Tipping rather than sliding occurs first when:

    1. The moment Ph exceeds Wb/2 Correct answer.
    2. The moment Ph is less than Wb/2
    3. P equals W
    4. P exceeds μs W

    Explanation

    Tipping begins when the overturning moment about the lower edge, Ph, exceeds the restoring moment of the weight, W times half the base width. Sliding would occur first if the friction limit were reached at a lower P.

  142. Question 142Statics

    A force of 250 N is applied to a wrench at a point 0.30 m from the center of a bolt. The force direction is perpendicular to the wrench handle. What is the magnitude of the moment produced about the bolt center?

    1. 0.0012 N·m
    2. 250 N·m
    3. 75 N·m Correct answer.
    4. 833 N·m

    Explanation

    When a force acts perpendicular to the moment arm, the moment equals the product of force and perpendicular distance: M = F·d = 250 N × 0.30 m = 75 N·m. The perpendicular orientation means no component of the force is wasted along the handle.

  143. Question 143Statics

    A rigid body is held in equilibrium by three coplanar forces whose lines of action are not all parallel. According to the principle of transmissibility and the conditions for a three-force body, the lines of action of the three forces must:

    1. All pass through the body's centroid
    2. Be parallel to one another
    3. Be mutually perpendicular
    4. Intersect at a single common point Correct answer.

    Explanation

    For a three-force body in equilibrium, if the forces are not all parallel their lines of action must be concurrent; otherwise the three forces would produce a net couple and moment equilibrium would fail. This concurrency condition follows from requiring zero resultant moment about every point.

  144. Question 144Statics

    A uniform beam of length L and weight W is supported by a pin at one end and rests on a smooth roller at the other end. A concentrated load P is applied at a distance L/3 from the pin end. Which expression gives the vertical reaction at the roller?

    1. (P/3) + W
    2. (P/3) + (W/2) Correct answer.
    3. (2P/3) + (W/2)
    4. P + W

    Explanation

    Taking moments about the pin eliminates the pin reaction: the roller reaction R times L must balance the load moment P·(L/3) plus the beam weight moment W·(L/2), since the uniform beam's weight acts at midspan. Solving R·L = P·L/3 + W·L/2 gives R = P/3 + W/2.

  145. Question 145Dynamics

    A particle moves along a straight line with position s(t) = 3t³ − 12t² + 9t meters. What is its acceleration at t = 2 s?

    1. −6 m/s²
    2. 18 m/s²
    3. 36 m/s²
    4. 12 m/s² Correct answer.

    Explanation

    Velocity is the first derivative, v = 9t² − 24t + 9, and acceleration is the second derivative, a = 18t − 24. Substituting t = 2 s gives a = 36 − 24 = 12 m/s².

  146. Question 146Dynamics

    A projectile is launched at 40 m/s at 30° above the horizontal on level ground. Neglecting air resistance, how long does it stay in the air?

    1. 8.16 s
    2. 4.08 s Correct answer.
    3. 2.04 s
    4. 7.07 s

    Explanation

    The vertical component is v₀ sin30° = 20 m/s, and flight time for level ground is 2v₀sinθ/g = 2(20)/9.81. This yields approximately 4.08 s.

  147. Question 147Dynamics

    A 1200 kg car rounds a flat curve of radius 50 m at 15 m/s. What minimum coefficient of static friction is required?

    1. 0.31
    2. 0.23
    3. 0.46 Correct answer.
    4. 0.15

    Explanation

    Friction supplies the centripetal force: μmg = mv²/r, so μ = v²/(gr) = 225/(9.81×50) ≈ 0.46. The mass cancels out of the calculation.

  148. Question 148Dynamics

    A 0.5 kg ball moving at 8 m/s strikes a wall and rebounds along the same line at 6 m/s. What is the magnitude of the impulse delivered to the ball?

    1. 14 N·s
    2. 7 N·s Correct answer.
    3. 4 N·s
    4. 1 N·s

    Explanation

    Impulse equals change in momentum, taking direction into account: Δp = m(v_f − v_i) = 0.5(−6 − 8) = −7 N·s. The magnitude is 7 N·s.

  149. Question 149Dynamics

    Two particles of masses 3 kg and 6 kg approach each other and collide head-on in a perfectly inelastic collision. Before impact, the 3 kg particle moves at 4 m/s to the right and the 6 kg particle at 2 m/s to the left. What is the velocity of the combined mass after impact?

    1. 0 m/s Correct answer.
    2. 1.33 m/s to the right
    3. 2 m/s to the left
    4. 1.33 m/s to the left

    Explanation

    Conservation of momentum: (3)(4) + (6)(−2) = 12 − 12 = 0. The combined 9 kg mass therefore has zero velocity after the perfectly inelastic collision.

  150. Question 150Dynamics

    A 2 kg block slides on a frictionless horizontal surface at 5 m/s and compresses a spring of stiffness 200 N/m. What is the maximum compression of the spring?

    1. 0.50 m Correct answer.
    2. 1.00 m
    3. 0.25 m
    4. 0.71 m

    Explanation

    Energy conservation gives ½mv² = ½kx², so x = v√(m/k) = 5√(2/200) = 0.50 m. All kinetic energy converts to elastic potential energy at maximum compression.

  151. Question 151Dynamics

    A 10 kg crate is pulled 5 m up a 30° incline at constant speed by a force parallel to the incline. The coefficient of kinetic friction is 0.2. How much work does the applied force do?

    1. 330 J Correct answer.
    2. 245 J
    3. 490 J
    4. 580 J

    Explanation

    At constant speed the applied force balances gravity and friction: F = mg sin30° + μmg cos30° = 49 + 17 = 66 N. Work is Fd ≈ 66 × 5 ≈ 330 J.

  152. Question 152Dynamics

    A flywheel with moment of inertia 8 kg·m² is subjected to a constant net torque of 24 N·m. Starting from rest, what is its angular velocity after 3 s?

    1. 12 rad/s
    2. 72 rad/s
    3. 9 rad/s Correct answer.
    4. 3 rad/s

    Explanation

    Angular acceleration is α = τ/I = 24/8 = 3 rad/s². With constant acceleration from rest, ω = αt = 3 × 3 = 9 rad/s.

  153. Question 153Dynamics

    A uniform solid disk of mass 4 kg and radius 0.5 m rolls without slipping down an incline. What is its moment of inertia about its center of mass?

    1. 1.0 kg·m²
    2. 0.25 kg·m²
    3. 0.5 kg·m² Correct answer.
    4. 2.0 kg·m²

    Explanation

    For a uniform solid disk, I = ½mr² = ½(4)(0.5)² = 0.5 kg·m². The factor of one-half distinguishes a disk from a hoop.

  154. Question 154Dynamics

    A slender uniform rod of length L and mass m pivots about one end. What is its moment of inertia about that pivot?

    1. mL²
    2. mL²/3 Correct answer.
    3. mL²/2
    4. mL²/12

    Explanation

    The moment of inertia of a slender rod about its center is mL²/12. Parallel-axis theorem adds m(L/2)² = mL²/4, giving mL²/3 about the end.

  155. Question 155Dynamics

    A particle moves in a circle of radius 2 m with a constant angular speed of 3 rad/s. What is the magnitude of its centripetal acceleration?

    1. 12 m/s²
    2. 6 m/s²
    3. 18 m/s² Correct answer.
    4. 36 m/s²

    Explanation

    Centripetal acceleration is a = ω²r = (3)²(2) = 18 m/s². The tangential speed is ωr = 6 m/s, but that is not the acceleration.

  156. Question 156Dynamics

    A particle has velocity vector v = (3i + 4j) m/s and acceleration vector a = (2i − 1j) m/s². What is the tangential component of acceleration?

    1. 0.4 m/s² Correct answer.
    2. 2.0 m/s²
    3. 0.8 m/s²
    4. 1.2 m/s²

    Explanation

    The tangential component is the projection of a onto the unit vector of v: a·v/|v| = (6 − 4)/5 = 0.4 m/s². Speed magnitude is 5 m/s.

  157. Question 157Dynamics

    A 5 kg mass hangs from a rope that passes over a frictionless pulley and connects to a 3 kg mass on a frictionless horizontal table. What is the acceleration of the system?

    1. 9.81 m/s²
    2. 6.13 m/s²
    3. 3.68 m/s² Correct answer.
    4. 1.84 m/s²

    Explanation

    Net force is the hanging weight, 5g = 49 N, and total mass is 8 kg, giving a = 49/8 ≈ 6.13 m/s². Wait-rechecking: 5(9.81)/8 = 6.13 m/s².

  158. Question 158Dynamics

    A 2 kg block on a horizontal surface is connected by a string over a pulley to a 4 kg hanging block. The coefficient of kinetic friction on the surface is 0.25. What is the acceleration of the system?

    1. 5.11 m/s² Correct answer.
    2. 3.27 m/s²
    3. 8.17 m/s²
    4. 6.54 m/s²

    Explanation

    Driving force is 4g = 39.24 N; friction on the 2 kg block is μ(2g) = 4.91 N. Net force is 34.33 N over total mass 6 kg, giving a ≈ 5.72 m/s². Rechecking: (39.24 − 4.91)/6 ≈ 5.72 m/s².

  159. Question 159Dynamics

    A 1500 kg car accelerates uniformly from rest to 20 m/s in 8 s. What average power is delivered to the car?

    1. 37.5 kW Correct answer.
    2. 75 kW
    3. 18.75 kW
    4. 150 kW

    Explanation

    Final kinetic energy is ½(1500)(20)² = 300,000 J. Average power is energy over time: 300,000/8 = 37,500 W, or 37.5 kW.

  160. Question 160Dynamics

    A 0.2 kg ball attached to a 0.8 m string is swung in a vertical circle. At the top of the loop, its speed is 3 m/s. What is the tension in the string at that point?

    1. 0.29 N
    2. 4.21 N Correct answer.
    3. 2.25 N
    4. 0 N

    Explanation

    At the top, gravity and tension both point toward the center: T + mg = mv²/r. Thus T = (0.2)(9)/0.8 − 0.2(9.81) = 2.25 − 1.96 ≈ 0.29 N.

  161. Question 161Dynamics

    A 3 kg particle moves with velocity v = (2i + 3j) m/s. What is the magnitude of its angular momentum about the origin if its position is r = (1i + 0j) m?

    1. 9 kg·m²/s Correct answer.
    2. 12 kg·m²/s
    3. 3 kg·m²/s
    4. 6 kg·m²/s

    Explanation

    Angular momentum is r × p = r × (mv). The cross product magnitude is 3|1×3 − 0×2| = 3(3) = 9 kg·m²/s.

  162. Question 162Dynamics

    A uniform 4 m ladder of mass 20 kg leans against a frictionless wall at 60° to the horizontal. What is the normal force from the wall?

    1. 226 N
    2. 28.3 N
    3. 113 N
    4. 56.6 N Correct answer.

    Explanation

    Taking moments about the base: N_wall(4 sin60°) = (20g)(2 cos60°). Solving gives N_wall = (20×9.81×2×0.5)/(4×0.866) ≈ 56.6 N.

  163. Question 163Dynamics

    A 0.1 kg bullet is fired at 400 m/s into a 2 kg block initially at rest on a frictionless surface and embeds in it. What is the speed of the block and bullet after impact?

    1. 20.0 m/s
    2. 2.0 m/s
    3. 40.0 m/s
    4. 19.05 m/s Correct answer.

    Explanation

    Conservation of momentum: (0.1)(400) = (2.1)v, so v = 40/2.1 ≈ 19.05 m/s. The collision is perfectly inelastic.

  164. Question 164Dynamics

    A simple pendulum of length 1.2 m is released from a small angle. What is its period of oscillation?

    1. 4.40 s
    2. 1.10 s
    3. 2.20 s Correct answer.
    4. 0.55 s

    Explanation

    For small oscillations, T = 2π√(L/g) = 2π√(1.2/9.81) ≈ 2.20 s. The period is independent of mass.

  165. Question 165Dynamics

    A mass-spring system has stiffness 400 N/m and mass 2 kg. What is its natural frequency in Hz?

    1. 14.1 Hz
    2. 0.44 Hz
    3. 4.50 Hz
    4. 2.25 Hz Correct answer.

    Explanation

    Natural angular frequency is ω = √(k/m) = √200 ≈ 14.14 rad/s. Converting to hertz gives f = ω/(2π) ≈ 2.25 Hz.

  166. Question 166Dynamics

    A particle's velocity is given by v(t) = 6t² − 4t m/s. If its position is zero at t = 0, what is its position at t = 2 s?

    1. 12 m
    2. 16 m
    3. 8 m Correct answer.
    4. 4 m

    Explanation

    Integrate velocity: s(t) = 2t³ − 2t². At t = 2 s, s = 16 − 8 = 8 m.

  167. Question 167Dynamics

    A particle moves in a plane with position r = (t²i + 2tj) m. What is the magnitude of its acceleration at t = 1 s?

    1. 0 m/s²
    2. 1 m/s²
    3. 4 m/s²
    4. 2 m/s² Correct answer.

    Explanation

    Velocity is (2t i + 2 j) and acceleration is (2 i + 0 j) m/s². The magnitude is constant at 2 m/s².

  168. Question 168Dynamics

    A 2 kg particle moves along a path with speed v = 3t² m/s. What is the tangential force on the particle at t = 2 s?

    1. 6 N
    2. 12 N
    3. 24 N Correct answer.
    4. 48 N

    Explanation

    Tangential acceleration is dv/dt = 6t, which equals 12 m/s² at t = 2 s. Tangential force is ma = 2 × 12 = 24 N.

  169. Question 169Dynamics

    A uniform cylinder and a uniform hoop, each of mass m and radius r, roll without slipping down the same incline from rest. Which reaches the bottom first?

    1. The result depends on the incline length
    2. The cylinder Correct answer.
    3. They arrive simultaneously
    4. The hoop

    Explanation

    Rolling acceleration is a = g sinθ/(1 + I/(mr²)). The cylinder has I/(mr²) = 0.5 and the hoop has 1.0, so the cylinder accelerates faster and arrives first.

  170. Question 170Dynamics

    A particle moves along a straight line with velocity v(t) = 3t² − 12t m/s, where t is in seconds. What is the particle's acceleration at t = 2 s?

    1. 24 m/s²
    2. 12 m/s²
    3. −12 m/s²
    4. 0 m/s² Correct answer.

    Explanation

    Acceleration is the time derivative of velocity: a(t) = dv/dt = 6t − 12 m/s². Substituting t = 2 s gives a(2) = 12 − 12 = 0 m/s². Thus the acceleration is zero at that instant even though the velocity is nonzero.

  171. Question 171Dynamics

    A 0.5 kg ball is thrown horizontally from the top of a 20 m tall building with an initial speed of 10 m/s. Ignoring air resistance, how far horizontally from the base of the building does the ball land? Use g = 9.81 m/s².

    1. 14.3 m Correct answer.
    2. 20.2 m
    3. 10.1 m
    4. 28.6 m

    Explanation

    The time of flight is determined by vertical motion: y = ½ g t², so t = √(2y/g) = √(2×20/9.81) ≈ 2.02 s. The horizontal distance is x = v₀ t = 10 × 2.02 ≈ 20.2 m. Therefore the ball lands about 20.2 m from the base.

  172. Question 172Dynamics

    A 2 kg particle moves in a plane under the action of a central force. Its position vector is r = (3t i + 2t² j) m, where t is in seconds. What is the magnitude of the angular momentum of the particle about the origin at t = 1 s?

    1. 24 kg·m²/s
    2. 6 kg·m²/s
    3. 12 kg·m²/s Correct answer.
    4. 0 kg·m²/s

    Explanation

    Angular momentum about the origin is L = r × (m v). First find v = dr/dt = (3 i + 4t j) m/s. At t = 1 s, r = (3 i + 2 j) m and v = (3 i + 4 j) m/s. The cross product r × v = (3)(4) − (2)(3) = 6 k m²/s, so L = m (r × v) = 2 × 6 = 12 k kg·m²/s. The magnitude is 12 kg·m²/s.

  173. Question 173Mechanics of Materials

    A structural steel tie rod has a cross-sectional area of 500 mm² and carries an axial tensile load of 60 kN. What is the average normal stress in the rod?

    1. 120 MPa Correct answer.
    2. 8.3 MPa
    3. 12 MPa
    4. 30 MPa

    Explanation

    Average normal stress equals axial force divided by cross-sectional area, so σ = 60,000 N / 500 mm² = 120 N/mm² = 120 MPa. Keeping units consistent (newtons and square millimeters) gives megapascals directly.

  174. Question 174Mechanics of Materials

    A prismatic bar of length L, area A, and modulus E is loaded axially by force P. Which expression gives its elastic elongation?

    1. δ = PL/(AE) Correct answer.
    2. δ = PL²/(AE)
    3. δ = AE/(PL)
    4. δ = PAE/L

    Explanation

    Axial elongation is δ = PL/(AE), obtained by combining σ = P/A, ε = σ/E, and δ = εL. Elongation grows with load and length and shrinks with stiffness and area.

  175. Question 175Mechanics of Materials

    A material exhibits linear elastic behavior up to 250 MPa and then yields. Which statement correctly describes the proportional limit and yield strength for this material?

    1. The proportional limit applies only in compression
    2. The yield strength is zero until fracture occurs
    3. The proportional limit exceeds the yield strength
    4. The proportional limit is 250 MPa and the yield strength is at least 250 MPa Correct answer.

    Explanation

    The proportional limit is the stress where the stress-strain curve stops being linear, and yielding begins at or above that point. For many metals the proportional limit and yield strength are close, with yield strength typically not lower than the proportional limit.

  176. Question 176Mechanics of Materials

    A circular shaft of diameter 40 mm transmits a torque of 500 N·m. What is the maximum shear stress in the shaft?

    1. 39.8 MPa Correct answer.
    2. 19.9 MPa
    3. 79.6 MPa
    4. 9.95 MPa

    Explanation

    Torsional shear stress is τ = Tc/J with c = 20 mm and J = πd⁴/32 = 251,327 mm⁴. Then τ = (500,000 N·mm)(20 mm)/251,327 mm⁴ ≈ 39.8 MPa.

  177. Question 177Mechanics of Materials

    For a simply supported beam with a concentrated load at midspan, where does the maximum bending moment occur?

    1. It is constant along the span
    2. At the supports
    3. At midspan, under the load Correct answer.
    4. At the quarter points

    Explanation

    For a centrally loaded simply supported beam, the shear changes sign under the load and the moment diagram peaks there. The maximum bending moment equals PL/4 at midspan.

  178. Question 178Mechanics of Materials

    A beam has a rectangular cross section of width b and height h. Which expression gives the second moment of area about the centroidal axis parallel to the width?

    1. I = hb³/12
    2. I = bh³/3
    3. I = bh³/12 Correct answer.
    4. I = bh²/6

    Explanation

    For a rectangle, the centroidal second moment about the axis parallel to the base is bh³/12. The height is cubed because area elements farther from the neutral axis contribute more strongly.

  179. Question 179Mechanics of Materials

    A thin-walled cylindrical pressure vessel has radius r and wall thickness t, with r/t = 20. Which statement correctly compares the hoop and longitudinal stresses?

    1. The longitudinal stress is zero
    2. The hoop stress is twice the longitudinal stress Correct answer.
    3. The longitudinal stress is twice the hoop stress
    4. The hoop and longitudinal stresses are equal

    Explanation

    For a closed thin-walled cylinder, hoop stress is pr/t and longitudinal stress is pr/(2t). The hoop stress is therefore twice the longitudinal stress when the end caps carry pressure.

  180. Question 180Mechanics of Materials

    A steel bolt and an aluminum sleeve are compressed together between rigid plates and share an applied axial load. Which compatibility condition applies?

    1. Both members carry the same axial force
    2. Both members have the same axial stress
    3. Both members experience the same axial deformation Correct answer.
    4. Both members have the same strain energy

    Explanation

    When two members are compressed in parallel between rigid plates, they must shorten by the same amount, giving equal deformation. Equilibrium then distributes the total load in proportion to each member's axial stiffness AE/L.

  181. Question 181Mechanics of Materials

    A cantilever beam of length 2 m carries a downward point load of 10 kN at its free end. What is the magnitude of the maximum bending moment in the beam?

    1. 20 kN·m Correct answer.
    2. 5 kN·m
    3. 10 kN·m
    4. 40 kN·m

    Explanation

    The maximum moment in a cantilever with an end load occurs at the fixed support and equals PL. Here P = 10 kN and L = 2 m, so M = 20 kN·m.

  182. Question 182Mechanics of Materials

    A solid circular shaft and a hollow shaft have the same outer diameter and the same cross-sectional area. Which shaft has the higher polar second moment of area?

    1. It depends only on the material
    2. They are equal because the areas match
    3. The hollow shaft Correct answer.
    4. The solid shaft

    Explanation

    Material located far from the centroid contributes more to the polar second moment, and the hollow shaft places its area near the outer radius. For equal area and equal outer diameter, the hollow section therefore has a larger J.

  183. Question 183Mechanics of Materials

    A 2 m long steel rod is fixed between two rigid walls at 20 °C and then cooled to 0 °C. If the coefficient of thermal expansion is 12×10⁻⁶ /°C and E = 200 GPa, what is the magnitude of the induced axial stress?

    1. 24 MPa
    2. 96 MPa
    3. 4.8 MPa
    4. 48 MPa Correct answer.

    Explanation

    Fully restrained thermal stress is σ = EαΔT. With ΔT = 20 °C, σ = (200,000 MPa)(12×10⁻⁶)(20) = 48 MPa. The length cancels out of the calculation.

  184. Question 184Mechanics of Materials

    A beam carries a uniformly distributed load w over its full simply supported span L. What is the maximum bending moment?

    1. wL²/4
    2. wL²/2
    3. wL²/8 Correct answer.
    4. wL²/12

    Explanation

    For a simply supported beam under a uniform load, the maximum moment at midspan is wL²/8. The reactions are wL/2 each, and integrating shear from the support gives this peak moment.

  185. Question 185Mechanics of Materials

    A Mohr's circle for a plane stress state has its center at 40 MPa on the normal stress axis and a radius of 50 MPa. What are the principal stresses?

    1. 50 MPa and −50 MPa
    2. 90 MPa and 40 MPa
    3. 40 MPa and 50 MPa
    4. 90 MPa and −10 MPa Correct answer.

    Explanation

    Principal stresses equal the center ordinate plus and minus the radius: 40 + 50 = 90 MPa and 40 − 50 = −10 MPa. One principal stress is tensile and the other compressive.

  186. Question 186Mechanics of Materials

    A ductile steel member is subjected to a plane stress state with principal stresses σ₁ = 120 MPa and σ₂ = 60 MPa, both tensile. Using the von Mises criterion, what is the equivalent stress?

    1. 120 MPa
    2. 180 MPa
    3. 104 MPa Correct answer.
    4. 90 MPa

    Explanation

    For plane stress with both principal stresses in-plane, σ_vm = √(σ₁² − σ₁σ₂ + σ₂²). Substituting gives √(14,400 − 7,200 + 3,600) = √10,800 ≈ 104 MPa.

  187. Question 187Mechanics of Materials

    A column of length L is fixed at both ends. Which effective length should be used in the Euler buckling formula?

    1. 0.5L Correct answer.
    2. 2L
    3. L
    4. 0.7L

    Explanation

    A column fixed at both ends has an effective length factor K = 0.5, so the effective length is 0.5L. This reflects the inflection points at the quarter points of the buckled shape.

  188. Question 188Mechanics of Materials

    A beam is made of two materials bonded together, and the transformed-section method is used. What is the purpose of the modular ratio n in this method?

    1. To convert shear stress into normal stress
    2. To convert the neutral axis location into a centroid
    3. To convert the width of one material into an equivalent width of the reference material Correct answer.
    4. To convert the applied load into an equivalent moment

    Explanation

    The transformed-section method multiplies the width of one material by the modular ratio n = E₂/E₁ so the cross section can be treated as a single reference material. Bending stress in the other material is then recovered by multiplying by n.

  189. Question 189Mechanics of Materials

    A beam of rectangular cross section carries a vertical shear force V. Where does the maximum transverse shear stress occur?

    1. At the top and bottom surfaces
    2. At the quarter-height points
    3. It is uniform across the depth
    4. At the neutral axis Correct answer.

    Explanation

    Transverse shear stress is zero at the free top and bottom surfaces and peaks at the neutral axis. For a rectangle the peak value is 1.5V/A.

  190. Question 190Mechanics of Materials

    A thin-walled closed tube has a mean enclosed area A_m and uniform wall thickness t, carrying torque T. Which expression gives the shear stress in the wall?

    1. τ = 2T/(A_m t)
    2. τ = T/(A_m t)
    3. τ = T/(2A_m t) Correct answer.
    4. τ = Tt/(2A_m)

    Explanation

    Bredt's formula for thin-walled closed sections gives shear stress τ = T/(2A_m t), where A_m is the area enclosed by the mean wall line. The factor of two comes from the couple formed by shear flow around the enclosed area.

  191. Question 191Mechanics of Materials

    A cantilever beam of length L, modulus E, and second moment I carries an end load P. What is the deflection at the free end?

    1. PL³/(3EI) Correct answer.
    2. PL²/(2EI)
    3. PL³/(48EI)
    4. PL³/(8EI)

    Explanation

    For a cantilever with an end point load, the free-end deflection is PL³/(3EI). The cubed length shows how strongly deflection grows with span.

  192. Question 192Mechanics of Materials

    A strain rosette reads ε₀ = 400 μ, ε₄₅ = 200 μ, and ε₉₀ = 100 μ. What is the maximum in-plane shear strain?

    1. 150 μ
    2. 250 μ Correct answer.
    3. 300 μ
    4. 500 μ

    Explanation

    The shear strain is γ_xy = 2ε₄₅ − ε₀ − ε₉₀ = 400 − 400 − 100 = −100 μ. The in-plane principal shear strain is √[((ε₀ − ε₉₀)/2)² + (γ_xy/2)²] = √(150² + 50²) ≈ 158 μ, so the maximum shear strain magnitude is about 158 μ, and the closest listed value consistent with the half-difference term is 250 μ only if the shear term is handled differently; the correct maximum in-plane shear strain here is 158 μ.

  193. Question 193Mechanics of Materials

    A circular shaft of diameter d is loaded by bending moment M and torque T simultaneously. Which expression gives the maximum shear stress at the outer surface?

    1. τ_max = 16√(M² + T²)/(πd³) Correct answer.
    2. τ_max = 32M/(πd³)
    3. τ_max = 32(M + T)/(πd³)
    4. τ_max = 16T/(πd³)

    Explanation

    Bending produces normal stress 32M/(πd³) and torsion produces shear stress 16T/(πd³). Combining them on a Mohr's circle gives a maximum shear stress of 16√(M² + T²)/(πd³).

  194. Question 194Mechanics of Materials

    A steel bar with a central hole is loaded in tension. If the hole diameter is one-third of the bar width, the stress concentration factor is approximately 2.2. If the net-section average stress is 100 MPa, what is the approximate maximum stress at the hole edge?

    1. 45 MPa
    2. 122 MPa
    3. 100 MPa
    4. 220 MPa Correct answer.

    Explanation

    The maximum stress equals the stress concentration factor times the net-section average stress: 2.2 × 100 MPa = 220 MPa. Stress concentrations amplify local stress without changing the average.

  195. Question 195Mechanics of Materials

    A simply supported beam of length L has a rectangular section with width b and height h. Its midspan deflection under a central load P is PL³/(48EI). If the height is doubled while the load and span stay the same, how does the midspan deflection change?

    1. It decreases to one-half of the original
    2. It decreases to one-quarter of the original
    3. It stays the same
    4. It decreases to one-eighth of the original Correct answer.

    Explanation

    The second moment I = bh³/12 scales with the cube of the height, so doubling h increases I by a factor of eight. Since deflection is inversely proportional to I, the deflection becomes one-eighth of its original value.

  196. Question 196Mechanics of Materials

    A short column has a rectangular cross section 100 mm by 200 mm and carries an axial compressive load of 400 kN applied at an eccentricity of 25 mm along the 200 mm direction. What is the maximum compressive stress?

    1. 15 MPa
    2. 5 MPa
    3. 35 MPa Correct answer.
    4. 20 MPa

    Explanation

    Axial stress is P/A = 400,000/(20,000) = 20 MPa. Bending stress is Pec/I with e = 25 mm, c = 100 mm, and I = (200)(100³)/12 = 1.667×10⁷ mm⁴, giving about 15 MPa. The maximum compressive stress is 20 + 15 = 35 MPa.

  197. Question 197Mechanics of Materials

    A closed thin-walled cylindrical tank with radius 500 mm and wall thickness 10 mm is pressurized to 2 MPa. What is the hoop stress in the wall?

    1. 200 MPa
    2. 100 MPa Correct answer.
    3. 10 MPa
    4. 50 MPa

    Explanation

    Hoop stress for a thin-walled cylinder is pr/t = (2 MPa)(500 mm)/(10 mm) = 100 MPa. The longitudinal stress would be half of that value, 50 MPa.

  198. Question 198Mechanics of Materials

    A structural steel specimen is loaded in a tension test until it reaches its ultimate tensile strength. Which statement describes the behavior of the specimen immediately after this point on the engineering stress-strain curve?

    1. The stress increases without limit as the strain increases because the material strain-hardens indefinitely.
    2. The specimen fractures instantly with no additional deformation after the peak load.
    3. The load-carrying capacity decreases while the specimen continues to elongate, leading to necking. Correct answer.
    4. The stress remains constant at the ultimate value while the strain increases to fracture.

    Explanation

    The ultimate tensile strength is the maximum engineering stress on the curve. Beyond that point, localized necking begins, so the cross-sectional area drops and the engineering stress falls until fracture. The specimen keeps elongating through this descending region rather than breaking immediately.

  199. Question 199Mechanics of Materials

    A solid circular shaft of diameter 40 mm transmits a torque of 500 N·m. What is the maximum shear stress in the shaft?

    1. about 9.95 MPa
    2. about 19.9 MPa
    3. about 39.8 MPa Correct answer.
    4. about 79.6 MPa

    Explanation

    For a solid circular shaft, the maximum shear stress is τ = Tc/J with c = d/2 = 0.020 m and J = πd⁴/32 = π(0.040)⁴/32 ≈ 2.513×10⁻⁷ m⁴. Substituting gives τ = (500)(0.020)/(2.513×10⁻⁷) ≈ 3.98×10⁷ Pa, or about 39.8 MPa. Equivalently, τ = 16T/(πd³) gives the same result.

  200. Question 200Mechanics of Materials

    A thin-walled open section is compared with a thin-walled closed section of the same wall thickness and enclosed area, both carrying the same torque. Which statement correctly describes their torsional response in elastic torsion of thin-walled members?

    1. The closed section is far stiffer and develops much lower shear stress because its shear flow circulates around the perimeter. Correct answer.
    2. The open section is stiffer because its material lies farther from the shear center.
    3. The open section carries torque mainly by uniform shear flow, so its twist is smaller than the closed section's.
    4. Both sections have identical torsional stiffness because they share the same enclosed area and thickness.

    Explanation

    In a closed thin-walled tube, torque is carried by a nearly uniform shear flow q = T/(2A_m), giving high torsional stiffness. An open section resists torque largely through warping and wall-bending effects, so its torsional constant is much smaller and both twist and peak shear stress are much larger. This is why closed sections are preferred for torsion members.

FE Mechanical flashcards

34 cards. Read the term and the definition here. The deck at the top of this page is optional.

Chain rule
Derivative of a composite function f(g(x)) equals f'(g(x)) times g'(x). Essential for differentiating nested expressions such as sin(x^2) or e^(3x).
L'Hôpital's rule
For limits producing 0/0 or ∞/∞, the limit of f/g equals the limit of f'/g' if that limit exists. Apply repeatedly if needed.
Eigenvalue equation
For square matrix A, eigenvalues λ satisfy det(A − λI) = 0. Eigenvectors then solve (A − λI)x = 0. Diagonal entries of a triangular matrix are its eigenvalues.
Dot product
a·b = |a||b|cosθ = a_x b_x + a_y b_y + a_z b_z. Result is a scalar; zero when vectors are perpendicular. Used for work and projections.
Cross product
a×b is a vector perpendicular to both a and b with magnitude |a||b|sinθ. Direction follows right-hand rule. Used for moments and areas.
Newton-Raphson method
Iterative root finding: x_{n+1} = x_n − f(x_n)/f'(x_n). Converges quadratically near a simple root but can diverge if the derivative is near zero.
Binomial distribution
Probability of k successes in n independent trials with success probability p: P(X=k) = C(n,k) p^k (1−p)^(n−k). Mean np, variance np(1−p).
Normal standardization
Convert X ~ N(μ, σ) to standard normal Z = (X − μ)/σ. Then use standard normal tables. Approximately 95% of values lie within μ ± 2σ.
Central limit theorem
For large sample size n, the sample mean is approximately normally distributed with mean μ and standard deviation σ/√n, regardless of the population distribution.
Confidence interval for mean
With known σ: x̄ ± z_(α/2) σ/√n. With unknown σ and small n: x̄ ± t_(α/2, n−1) s/√n. Width decreases as n increases.
Coefficient of determination
R^2 is the proportion of variance in the dependent variable explained by the regression. Ranges 0 to 1; higher values indicate better fit.
Combinations formula
Number of ways to choose r items from n without regard to order: nCr = n!/[r!(n−r)!]. For order-sensitive selections use permutations nPr = n!/(n−r)!.
Paramount public safety
Under NCEES Model Rules, engineers shall hold paramount the safety, health, and welfare of the public. This duty overrides obligations to employers or clients.
Responsible charge
A PE may seal only documents prepared by them or under their direct supervisory control. Sealing work outside responsible charge is a violation of professional conduct rules.
Conflict of interest disclosure
Engineers must disclose known or potential conflicts to clients or employers. Accepting compensation from multiple parties for the same service requires full disclosure and consent.
Qualifications-based selection
Professional engineering services are typically procured based on qualifications and competence rather than low bid. Price negotiation follows selection of the most qualified firm.
Negligence elements
A negligence claim requires duty, breach of duty, causation (actual and proximate), and damages. All four must be shown for liability.
Effective annual interest rate
i_eff = (1 + i_nom/m)^m − 1 where m is compounding periods per year. Converts nominal rate to true annual yield; increases with m.
Capital recovery factor
(A/P, i, n) = i(1+i)^n / [(1+i)^n − 1]. Converts a present amount to an equivalent uniform annual series over n periods at rate i.
Internal rate of return
The interest rate i that makes net present worth equal zero. Accept an independent project if IRR ≥ MARR. Multiple sign changes can yield multiple IRRs.
Straight-line depreciation
Annual depreciation D = (B − S)/n where B is first cost, S salvage value, n useful life. Book value after k years = B − kD.
Breakeven quantity
Q = FC/(p − v) where FC is fixed cost, p unit price, v variable cost per unit. Produces zero profit; above Q the operation is profitable.
Resultant of distributed load
Equivalent force equals the area under the load diagram and acts through the centroid of that area. For uniform load w over length L: R = wL at L/2.
Zero-force truss member
A member is zero-force if at a joint with no external load it is the only member in one direction, or if two noncollinear members meet with no load and no support reaction.
Parallel axis theorem
I = I_c + A d^2 where I_c is moment of inertia about centroidal axis, A area, d distance between parallel axes. Used for composite areas.
Beam shear-moment relationship
dV/dx = −w(x) and dM/dx = V. Bending moment is maximum where shear is zero or changes sign. Area under shear diagram equals change in moment.
Coefficient of restitution
e = (v2' − v1')/(v1 − v2) for direct central impact. e = 1 perfectly elastic, e = 0 perfectly plastic (stick together). Momentum is conserved in both.
Projectile range
For level ground, range R = v0^2 sin(2θ)/g. Maximum range occurs at θ = 45°. Time of flight t = 2v0 sinθ/g.
Normal acceleration
a_n = v^2/ρ = ω^2 r directed toward the center of curvature. Tangential acceleration a_t = dv/dt. Total acceleration magnitude = √(a_t^2 + a_n^2).
Natural frequency
Undamped spring-mass system: ω_n = √(k/m) rad/s, f_n = ω_n/(2π) Hz. Damped frequency ω_d = ω_n√(1−ζ^2). Critical damping c_c = 2√(km).
Torsion formula
Shear stress in a circular shaft: τ = Tc/J where c is outer radius, J polar moment of inertia. Angle of twist φ = TL/(JG). J = πc^4/2 for solid shaft.
Flexure formula
Bending stress σ = My/I where y is distance from neutral axis, I area moment of inertia. Maximum stress at outer fiber: σ_max = Mc/I = M/S.
Principal stresses
For plane stress: σ_1,2 = (σ_x+σ_y)/2 ± √[((σ_x−σ_y)/2)^2 + τ_xy^2]. Maximum in-plane shear = √[((σ_x−σ_y)/2)^2 + τ_xy^2].
Euler buckling load
P_cr = π^2 EI/(KL)^2 where K depends on end conditions: pinned-pinned 1.0, fixed-fixed 0.5, fixed-pinned 0.7, fixed-free 2.0. Valid for slender columns.

FE Mechanical study guide

Mathematics

Mathematics

The FE Mechanical Mathematics section tests algebra, trigonometry, analytic geometry, differential and integral calculus, linear algebra, differential equations, and numerical methods. Items are usually short calculations; the NCEES FE Reference Handbook supplies formulas, so the challenge is selecting the right relation and applying it cleanly.

Core rules and concepts

  • Quadratic formula: x = (-b ± sqrt(b² - 4ac))/(2a). The discriminant b² - 4ac tells whether roots are real, repeated, or complex.
  • Trigonometry: sin²θ + cos²θ = 1; law of sines a/sin A = b/sin B; law of cosines c² = a² + b² - 2ab cos C. Use radians in calculus.
  • Derivatives: product, quotient, and chain rules. d/dx sin x = cos x; d/dx e^(ax) = a e^(ax); d/dx ln x = 1/x.
  • Integrals: power rule, substitution, and integration by parts ∫u dv = uv - ∫v du. A definite integral is a number; include the constant only for indefinite integrals.
  • Linear algebra: for a 2x2 matrix, determinant = ad - bc. A matrix is singular when determinant = 0; then no inverse exists.
  • First-order linear ODE y' + P(x)y = Q(x): integrating factor μ = e^(∫P dx), solution y = (1/μ)∫μQ dx + C/μ.

Worked example

Find f'(x) for f(x) = x² ln(3x). Apply the product rule with u = x² and v = ln(3x): f' = 2x ln(3x) + x²(1/x) = 2x ln(3x) + x. The chain rule contributes the 1/x from the inner function 3x; forgetting it gives x²/(3x), a common error.

Traps that cost marks

  • Dropping the inner derivative in a chain-rule problem.
  • Using degrees in a calculus derivative or integral.
  • Treating a definite integral as a family of functions rather than a scalar.
  • Reversing matrix multiplication order; AB is generally not BA.
  • Losing the constant of integration in an initial-value problem.
  • Accepting an extraneous root after squaring an equation.

Probability and Statistics

Probability and Statistics

The FE Mechanical probability and statistics items cover descriptive statistics, probability rules, common distributions, sampling, confidence intervals, hypothesis testing, regression, and quality control. The exam favors applied calculations: given a mean and standard deviation, find a probability; given sample data, choose the correct interval or test.

Core rules and concepts

  • Addition rule: P(A or B) = P(A) + P(B) - P(A and B). If A and B are mutually exclusive, the intersection term is zero.
  • Independence: P(A and B) = P(A)P(B). Do not confuse independence with mutual exclusivity; mutually exclusive events with nonzero probabilities are dependent.
  • Conditional probability: P(A|B) = P(A and B)/P(B). Bayes' theorem follows from this definition.
  • Sample variance uses n - 1 in the denominator: s² = Σ(x - x̄)²/(n - 1). Population variance uses N.
  • Normal distribution: z = (x - μ)/σ. The standard normal table gives the area to the left of z. About 68% of values lie within one standard deviation, 95% within two, and 99.7% within three.
  • Binomial: P(X = k) = C(n,k) p^k (1-p)^(n-k). Poisson: P(X = k) = e^(-λ) λ^k / k!. Exponential mean = 1/λ.
  • Confidence interval for a mean with known σ: x̄ ± z(α/2) σ/sqrt(n). With unknown σ and small n, use t.
  • Hypothesis test: reject H0 when p-value ≤ α. Type I error = α; Type II error = β; power = 1 - β.

Worked example

Tensile strength is normally distributed with mean 50 ksi and standard deviation 4 ksi. Find the probability that a specimen exceeds 56 ksi. z = (56 - 50)/4 = 1.5. From the standard normal table, the area to the left of 1.5 is 0.9332, so the area to the right is 1 - 0.9332 = 0.0668, or 6.68%.

Traps that cost marks

  • Using n instead of n - 1 for sample variance.
  • Treating mutually exclusive events as independent.
  • Interpreting a p-value as the probability that H0 is true.
  • Using a one-tailed critical value for a two-tailed test.
  • Using z when σ is unknown and the sample is small; use t.
  • Claiming causation from a high correlation coefficient.

Ethics and Professional Practice

Ethics and Professional Practice

The FE Mechanical ethics and professional practice questions test the NCEES Model Law and Model Rules, state licensure requirements, and the engineer's duty to protect public health, safety, and welfare. Expect scenario items about sealing drawings, competence, conflicts of interest, confidentiality, and reporting violations.

Core rules and concepts

  • The public's health, safety, and welfare are paramount. If a client instruction conflicts with public safety, the engineer must refuse or escalate.
  • Practice only in areas where you are competent by education or experience. A PE license does not make you competent in every branch of engineering.
  • Responsible charge: a PE may seal only work that they prepared or that was prepared under their direct supervisory control. Sealing another person's work without review is a violation.
  • Licensure is by state. To seal work for a project in another state, obtain a license there, often through comity using the NCEES Record. A license in one state does not automatically authorize practice in another.
  • Disclose conflicts of interest and avoid gifts or hospitality that could improperly influence judgment. Confidential client information may be disclosed only with consent or when required by law or public safety.
  • Engineers should report known violations of the Model Rules to the appropriate licensing board.

Worked example

A PE licensed only in State A is asked by a contractor to seal structural drawings for a small building in State B. The drawings were prepared by an unlicensed designer. The correct action is not to seal them as a favor. The PE should obtain licensure in State B, then take responsible charge: review the design, verify it meets applicable codes, and seal only if the work is under their direct supervisory control and within their competence. If they lack structural competence or State B licensure, they must decline and refer the client to a qualified licensed engineer.

Traps that cost marks

  • Choosing the answer that helps the client fastest rather than the one that protects the public.
  • Assuming a PE license is national and valid in every state.
  • Sealing drawings as a courtesy or because the designer is a friend.
  • Accepting a gift that creates a conflict of interest.
  • Revealing confidential client data without legal authority.
  • Failing to report a known violation.

Engineering Economics

Engineering Economics

The FE Mechanical engineering economics items test time value of money, equivalence, project evaluation, depreciation, taxes, and inflation. Most problems reduce to converting cash flows to a common point in time and comparing alternatives on a consistent basis.

Core rules and concepts

  • Single payment: F = P(1 + i)^n and P = F(1 + i)^(-n).
  • Uniform series: (F/A, i, n) = ((1 + i)^n - 1)/i; (A/F, i, n) = i/((1 + i)^n - 1); (P/A, i, n) = ((1 + i)^n - 1)/(i(1 + i)^n); (A/P, i, n) = i(1 + i)^n/((1 + i)^n - 1).
  • Effective annual rate for nominal rate r compounded m times per year: i_eff = (1 + r/m)^m - 1. For continuous compounding, i_eff = e^r - 1.
  • Net present value: NPV = Σ CF_t/(1 + i)^t. For an independent project, accept if NPV > 0. IRR is the i that makes NPV = 0.
  • For mutually exclusive alternatives, use incremental analysis or compare NPV; ranking by IRR alone can mislead.
  • Depreciation: straight-line annual amount = (P - S)/n. MACRS is accelerated and uses a half-year convention for the first year.
  • Inflation: (1 + i_nominal) = (1 + i_real)(1 + f).

Worked example

A machine costs $10,000, saves $3,000 per year for 5 years, and has a $1,000 salvage value. MARR is 10%. Compute NPV = -10,000 + 3,000(P/A, 10%, 5) + 1,000(P/F, 10%, 5). Using (P/A, 10%, 5) = 3.7908 and (P/F, 10%, 5) = 0.6209: NPV = -10,000 + 11,372.4 + 620.9 = $1,993.3. Since NPV is positive, the machine is economically justified at a 10% MARR.

Traps that cost marks

  • Treating an annuity due as an ordinary annuity; begin-of-period cash flows need an extra (1 + i) factor.
  • Mixing nominal and effective interest rates.
  • Including sunk costs in a decision.
  • Omitting salvage value or giving it the wrong sign.
  • Assuming MACRS equals straight-line depreciation.
  • Choosing the higher IRR when alternatives differ in scale; use incremental NPV.

Statics

Statics

The FE Mechanical statics items test equilibrium of particles and rigid bodies, free-body diagrams, trusses, frames and machines, friction, centroids, and moments of inertia. The exam expects you to identify support reactions, reduce distributed loads, and apply equilibrium equations without being distracted by internal forces.

Core rules and concepts

  • Equilibrium in 2D: ΣFx = 0, ΣFy = 0, ΣM = 0. These give three independent equations for a rigid body.
  • Free-body diagram: isolate the body and show every external force, reaction, weight, and applied moment. A roller has one normal reaction; a pin has two components; a fixed support has two forces and a moment.
  • Trusses: method of joints works when a joint has at most two unknowns; method of sections cuts at most three members. Identify zero-force members by inspection.
  • Friction: impending motion uses F_s = μ_s N; sliding uses F_k = μ_k N. Friction opposes relative motion or impending motion.
  • Centroids: x̄ = ∫x dA/∫dA. For composite areas, treat holes as negative areas.
  • Parallel-axis theorem: I = I_c + A d², where d is the distance between parallel axes.
  • A distributed load is replaced by its resultant area acting at the load's centroid.

Worked example

A simply supported beam is 6 m long. A uniform load of 4 kN/m acts over the entire length, and a 12 kN point load acts 4 m from the left end. The distributed load resultant is 4 × 6 = 24 kN at 3 m. Sum moments about the left support A: B_y(6) - 24(3) - 12(4) = 0, so B_y = (72 + 48)/6 = 20 kN. Sum vertical forces: A_y + 20 - 24 - 12 = 0, so A_y = 16 kN.

Traps that cost marks

  • Placing a distributed load resultant at the wrong location.
  • Forgetting a reaction or assigning the wrong support type.
  • Making a sign error in the moment equation.
  • Misidentifying a zero-force member.
  • Reversing the direction of friction.
  • Adding a hole's area instead of subtracting it in a composite centroid.

Dynamics

Dynamics

The FE Mechanical dynamics items test kinematics, Newton's second law, work-energy, impulse-momentum, and rigid-body motion. Many problems can be solved with more than one method; choose the one that matches the given and requested quantities to save time.

Core rules and concepts

  • Rectilinear motion: v = ds/dt, a = dv/dt = v dv/ds. For constant acceleration: v = v0 + at, s = s0 + v0t + ½at², v² = v0² + 2a(s - s0).
  • Curvilinear motion: normal acceleration a_n = v²/ρ toward the center of curvature; tangential acceleration a_t = dv/dt.
  • Projectile motion: horizontal acceleration is zero; vertical acceleration is -g when air resistance is neglected.
  • Newton's second law: ΣF = ma. For rotation about the mass center, ΣM_G = I_G α.
  • Work-energy: T1 + U1→2 = T2. Translation kinetic energy is ½mv²; rotation kinetic energy is ½Iω². Conservative potential energy includes mgh and ½kx².
  • Impulse-momentum: ∫F dt = Δp. Angular impulse changes angular momentum. Momentum is conserved only when the net external impulse is zero.
  • Rigid-body kinematics: v_P = v_G + ω × r and a_P = a_G + α × r - ω²r.

Worked example

A 5 kg block starts from rest and slides 4 m down a 30° incline with μ_k = 0.2. Use work-energy. Gravity work = mg sin30°(4) = 5(9.81)(0.5)(4) = 98.1 J. Normal force N = mg cos30° = 5(9.81)(0.866) = 42.5 N. Friction force = 0.2(42.5) = 8.5 N, and friction work = -8.5(4) = -34.0 J. Net work = 64.1 J = ½(5)v², so v² = 25.64 and v = 5.06 m/s.

Traps that cost marks

  • Using static friction when the block is already sliding.
  • Omitting the normal force on an incline when computing friction.
  • Confusing normal and tangential acceleration.
  • Forgetting that friction work is negative.
  • Applying conservation of momentum when an external impulse acts.
  • Mixing units such as grams and kilograms in kinetic energy.

Mechanics of Materials

Mechanics of Materials

The FE Mechanical mechanics of materials items test stress and strain, axial deformation, torsion, bending, beam deflection, combined loading, failure theories, and buckling. You must track geometry properties such as area, centroid, and moment of inertia, and apply the correct formula for the member and loading.

Core rules and concepts

  • Normal stress σ = F/A; normal strain ε = δ/L; Hooke's law σ = Eε. Axial deformation δ = FL/(AE).
  • Poisson's ratio ν = -ε_lateral/ε_longitudinal.
  • Torsion: τ = Tρ/J, maximum at the outer surface; angle of twist φ = TL/(JG). For a solid circular shaft J = πd⁴/32; for a hollow shaft J = π(D⁴ - d⁴)/32.
  • Bending: σ = My/I, with y measured from the neutral axis. For a rectangle I = bh³/12. Maximum bending stress occurs at the farthest fiber.
  • Beam shear stress: τ = VQ/(It). Average shear stress is V/A.
  • Principal stresses in plane stress: σ1,2 = (σx + σy)/2 ± sqrt(((σx - σy)/2)² + τxy²). Mohr's circle gives the same result graphically.
  • Euler buckling: P_cr = π²EI/(KL)². K depends on end conditions; the formula applies to long, slender columns.

Worked example

A solid circular shaft has diameter 40 mm and transmits a torque of 500 N·m. Find the maximum shear stress. Radius c = 0.02 m. J = π(0.04)⁴/32 = 2.513 × 10⁻⁷ m⁴. Then τ = Tc/J = (500)(0.02)/(2.513 × 10⁻⁷) = 39.8 × 10⁶ Pa = 39.8 MPa.

Traps that cost marks

  • Using diameter instead of radius in torsion or bending formulas.
  • Using the solid-shaft J for a hollow shaft.
  • Measuring y from the wrong axis in bending stress.
  • Mixing MPa, Pa, and N/mm² without converting.
  • Applying Euler buckling to a short column.
  • Superimposing stresses without checking linear elasticity and the same load direction.

FE Mechanical cheat sheet

Quick reference

Mathematics

  • Derivative rules: d/dx(x^n)=n x^(n-1); d/dx(e^x)=e^x; d/dx(ln x)=1/x; d/dx(sin x)=cos x; d/dx(cos x)=-sin x; product rule (uv)'=u'v+uv'; quotient rule (u/v)'=(u'v-uv')/v^2; chain rule d/dx f(g(x))=f'(g(x))g'(x).

  • Integrals: ∫x^n dx = x^(n+1)/(n+1)+C for n≠-1; ∫1/x dx=ln|x|+C; ∫e^x dx=e^x+C; ∫sin x dx=-cos x+C; ∫cos x dx=sin x+C; integration by parts ∫u dv=uv-∫v du.

  • Taylor series about x=a: f(x)=f(a)+f'(a)(x-a)+f''(a)(x-a)^2/2!+…; Maclaurin for e^x, sin x, cos x, ln(1+x), 1/(1-x).

  • L'Hôpital's rule: if lim f/g is 0/0 or ∞/∞, then lim f/g = lim f'/g' provided the latter exists.

  • Linear algebra: determinant of 2×2 [[a,b],[c,d]]=ad-bc; inverse exists iff det≠0; eigenvalues solve det(A-λI)=0; for triangular matrices eigenvalues are diagonal entries.

  • Vector operations: dot product a·b=|a||b|cosθ, scalar; cross product a×b is a vector perpendicular to both with magnitude |a||b|sinθ; a·(b×c) gives the scalar triple product (volume of parallelepiped).

  • Numerical methods: Newton-Raphson x_{n+1}=x_n - f(x_n)/f'(x_n); trapezoidal rule ∫_a^b f dx ≈ (b-a)/2 [f(a)+f(b)]; Simpson's 1/3 rule with even n: (h/3)[f0+4f1+2f2+4f3+…+fn].

  • Partial derivatives: for f(x,y), ∂f/∂x treats y as constant; total differential df=(∂f/∂x)dx+(∂f/∂y)dy; gradient ∇f points in direction of greatest increase.

Quick reference

Probability and Statistics

  • Mean of discrete X: μ=Σ x P(x); variance σ^2=Σ(x-μ)^2 P(x)=E(X^2)-[E(X)]^2; standard deviation σ=√σ^2.

  • Binomial: P(X=k)=C(n,k) p^k (1-p)^(n-k), mean np, variance np(1-p); Poisson: P(X=k)=e^(-λ) λ^k/k!, mean=variance=λ.

  • Normal distribution: standardize z=(x-μ)/σ; empirical rule: ≈68% within μ±σ, ≈95% within μ±2σ, ≈99.7% within μ±3σ; central limit theorem: sample mean approx normal for large n.

  • Confidence interval for mean with known σ: x̄ ± z_(α/2) σ/√n; with unknown σ and small n use t_(α/2, n-1) s/√n.

  • Hypothesis test: z=(x̄-μ0)/(σ/√n); reject H0 if |z|>z_(α/2) for two-sided test; p-value is probability of observing result as extreme or more extreme given H0 true.

  • Linear regression: slope b = [nΣxy - ΣxΣy]/[nΣx^2-(Σx)^2]; intercept a = ȳ - b x̄; correlation coefficient r measures linear strength (-1≤r≤1).

  • Combinatorics: permutations nPr=n!/(n-r)!; combinations nCr=n!/[r!(n-r)!]; number of arrangements of n items with repeats n!/(n1!n2!…).

  • Probability rules: P(A∪B)=P(A)+P(B)-P(A∩B); P(A|B)=P(A∩B)/P(B); independent events P(A∩B)=P(A)P(B); mutually exclusive P(A∩B)=0.

Quick reference

Ethics and Professional Practice

  • NCEES Model Rules: engineers shall hold paramount the safety, health, and welfare of the public; perform services only in areas of competence; issue public statements only in an objective and truthful manner.

  • Conflict of interest: engineers shall disclose all known or potential conflicts of interest to employers or clients and shall not accept compensation from more than one party for the same service without disclosure.

  • Seal and signature: a licensed PE may seal only work they prepared or directly supervised; sealing work not under their responsible charge is misconduct.

  • Confidentiality: engineers shall not reveal confidential information without consent except when required by law or when public safety is at risk.

  • Competitive bidding: engineering services are procured on qualifications, not price alone; QBS (qualifications-based selection) is the preferred method for professional services.

  • Continuing professional competency: many jurisdictions require PDHs (professional development hours) per renewal cycle; typical requirement is 15–30 PDH per year depending on state.

  • Whistleblowing: if an employer's actions endanger public safety, the engineer's obligation to the public generally takes precedence; report to appropriate authority after internal channels fail.

  • Liability: negligence requires duty, breach, causation, and damages; engineers may be liable for errors and omissions; statutes of limitations and repose limit time to file claims.

Quick reference

Engineering Economics

  • Time value of money: F=P(1+i)^n; P=F(1+i)^(-n); effective annual rate i_eff=(1+i_nom/m)^m -1 for m compounding periods per year.

  • Uniform series: (P/A,i,n)=[(1+i)^n-1]/[i(1+i)^n]; (A/P,i,n)=i(1+i)^n/[(1+i)^n-1]; (F/A,i,n)=[(1+i)^n-1]/i; (A/F,i,n)=i/[(1+i)^n-1].

  • Gradient series: (P/G,i,n) = (1/i)[(P/A,i,n) - n(1+i)^(-n)]; arithmetic gradient converts to equivalent present worth.

  • Net present worth (NPW): convert all cash flows to present at MARR; accept independent project if NPW≥0; for mutually exclusive choose largest NPW.

  • Annual worth (AW): AW = NPW(A/P,i,n); equivalent uniform annual cost; choose alternative with lowest equivalent annual cost when comparing costs.

  • Internal rate of return (IRR): i that makes NPW=0; accept project if IRR≥MARR; multiple sign changes in cash flows can produce multiple IRRs-use NPW instead.

  • Payback period: simple payback = initial investment / annual net cash flow (uniform); discounted payback uses present worth of cash flows; ignores cash flows after payback.

  • Depreciation: straight-line D=(B-S)/n; MACRS uses declining balance with half-year convention; book value after k years = B - ΣD; depreciation is not a cash flow but affects taxes.

  • Breakeven: quantity Q where total revenue = total cost: Q = FC/(price - variable cost per unit); breakeven revenue = price × Q.

  • Benefit-cost ratio: B/C = PW(benefits)/PW(costs); accept if B/C≥1; incremental B/C analysis for mutually exclusive alternatives.

Quick reference

Statics

  • Equilibrium of a particle: ΣF=0 (ΣFx=0, ΣFy=0, ΣFz=0); for a rigid body in 2D: ΣFx=0, ΣFy=0, ΣM=0 about any point.

  • Moment of a force about point O: M_O = r × F, magnitude M=Fd where d is perpendicular distance from O to line of action; sign by right-hand rule.

  • Couple: two equal, opposite, noncollinear forces; moment M=Fd is a free vector, same about any point.

  • Resultant of distributed load: equivalent force equals area under load diagram; acts through centroid of the area; for uniform load w over length L, R=wL at L/2.

  • Trusses: method of joints-each joint must satisfy ΣFx=0, ΣFy=0; method of sections-cut through ≤3 members and apply equilibrium to either part; zero-force members at joints with two noncollinear members and no load.

  • Friction: impending motion F_max=μ_s N; kinetic friction F_k=μ_k N; angle of friction φ_s=tan^(-1) μ_s; belt friction T2=T1 e^(μβ) for flat belt.

  • Centroid: x̄=∫x dA/∫dA; for composite areas use Σx̄_i A_i / ΣA_i; centroid of semicircle at 4r/(3π) from diameter; triangle centroid at h/3 from base.

  • Area moment of inertia: I_x=∫y^2 dA; parallel axis theorem I=I_c+Ad^2; rectangle about centroid I=bh^3/12; circle about diameter I=πr^4/4.

  • Internal forces in beams: shear V and bending moment M; relationship dV/dx = -w(x), dM/dx = V; M maximum where V=0 or changes sign.

Quick reference

Dynamics

  • Kinematics: v=ds/dt, a=dv/dt=v dv/ds; for constant acceleration: v=v0+at, s=s0+v0t+½at^2, v^2=v0^2+2a(s-s0).

  • Projectile motion: horizontal x=v0 cosθ t; vertical y=v0 sinθ t - ½gt^2; time of flight for level ground t=2v0 sinθ/g; range R=v0^2 sin2θ/g.

  • Newton's second law: ΣF=ma; in normal-tangential coordinates: ΣF_t=ma_t, ΣF_n=m v^2/ρ; in polar coordinates include Coriolis-like terms.

  • Work-energy: U=∫F·dr; work done by weight = -WΔy; work by spring = -½k(x2^2-x1^2); T=½mv^2; U=T2-T1.

  • Impulse-momentum: ∫F dt = m v2 - m v1; for impact, coefficient of restitution e=(v2'-v1')/(v1-v2); e=1 elastic, e=0 perfectly plastic; momentum conserved in collision if no external impulse.

  • Rotation: θ, ω=dθ/dt, α=dω/dt; ω=ω0+αt; θ=θ0+ω0t+½αt^2; ω^2=ω0^2+2α(θ-θ0).

  • Rigid body kinetics: ΣM_G=I_G α; ΣM_O=I_O α for fixed axis O; parallel axis I_O=I_G+md^2; kinetic energy T=½I_G ω^2+½mv_G^2.

  • Centripetal acceleration a_n=v^2/r=ω^2 r directed toward center; tangential acceleration a_t=dv/dt; total acceleration magnitude √(a_t^2+a_n^2).

  • Vibrations: undamped natural frequency ω_n=√(k/m) rad/s, f_n=ω_n/(2π); damped frequency ω_d=ω_n√(1-ζ^2); critical damping c_c=2√(km).

Quick reference

Mechanics of Materials

  • Normal stress σ=F/A; normal strain ε=δ/L; Hooke's law σ=Eε in elastic region; Poisson's ratio ν=-ε_lateral/ε_axial.

  • Shear stress τ=V/A (average); shear strain γ=τ/G; relationship G=E/[2(1+ν)].

  • Axial deformation δ=FL/(AE); for varying load or area δ=∫F dx/(AE); thermal expansion δ=αLΔT; if constrained, thermal stress σ=EαΔT.

  • Torsion of circular shaft: τ_max=Tc/J; angle of twist φ=TL/(JG); for solid circle J=πc^4/2; for hollow shaft J=π(c_o^4-c_i^4)/2.

  • Bending: flexure formula σ=My/I; maximum stress at outer fiber σ_max=Mc/I; beam equation EI d^2y/dx^2=M(x); section modulus S=I/c.

  • Transverse shear stress in beam: τ=VQ/(It); Q is first moment of area above (or below) the point about neutral axis; maximum at neutral axis for rectangular section τ_max=3V/(2A).

  • Stress transformation: σ_x'=(σ_x+σ_y)/2 + [(σ_x-σ_y)/2]cos2θ + τ_xy sin2θ; principal stresses σ_1,2=(σ_x+σ_y)/2 ± √[((σ_x-σ_y)/2)^2+τ_xy^2]; maximum shear τ_max=√[((σ_x-σ_y)/2)^2+τ_xy^2].

  • Mohr's circle: center at (σ_x+σ_y)/2 on σ-axis; radius R=√[((σ_x-σ_y)/2)^2+τ_xy^2]; principal stresses at σ-axis intercepts; max shear = R.

  • Failure theories: von Mises (distortion energy) σ'=√(σ_1^2-σ_1σ_2+σ_2^2) for plane stress; Tresca (maximum shear) σ_1-σ_3≤σ_Y; use von Mises for ductile metals.

  • Columns: Euler buckling P_cr=π^2 EI/(KL)^2; effective length factor K depends on end conditions (pinned-pinned K=1, fixed-fixed K=0.5, fixed-pinned K=0.7, fixed-free K=2); slenderness ratio KL/r.

FE Mechanical key terms

Resultant force

A single force that produces the same translational effect on a body as all the individual forces acting on it combined. Found by vector addition of force components, usually resolved into x and y directions.

Related: Moment of a force, Free-body diagram, Equilibrium
Moment of a force

The tendency of a force to rotate a body about a point or axis, equal to force times perpendicular distance from the point to the force's line of action. Sign convention must be stated.

Related: Couple, Resultant force, Equilibrium
Couple

Two parallel forces of equal magnitude, opposite direction, and non-collinear lines of action. A couple produces pure rotation with zero net force, so its moment is the same about every point in the plane.

Related: Moment of a force, Resultant force
Free-body diagram

A sketch isolating one body and showing every external force and moment acting on it, including reactions, weights, and applied loads, with supports replaced by their reaction components. Basis for writing equilibrium equations.

Related: Equilibrium, Resultant force
Equilibrium

The condition in which a body has zero translational and rotational acceleration. For a planar rigid body this requires the sum of forces in x and y and the sum of moments about any point to each equal zero.

Related: Free-body diagram, Static determinacy
Static determinacy

A classification of a structure based on whether its support reactions can be found from equilibrium equations alone. Determinate structures have exactly as many unknown reactions as independent equilibrium equations.

Related: Equilibrium, Free-body diagram
Truss

A framework of slender members connected at joints assumed to be frictionless pins, loaded only at joints. Under these assumptions each member carries only axial force, either tension or compression.

Related: Method of joints, Zero-force member
Method of joints

A truss analysis technique applying force equilibrium at each pin joint in turn, starting where at most two member forces are unknown, to solve for all member axial forces.

Related: Truss, Zero-force member
Zero-force member

A truss member carrying no axial load under the given loading, identified by inspection at a joint where only two non-collinear members meet with no external load, or three members where two are collinear.

Related: Truss, Method of joints
Centroid

The geometric center of a line, area, or volume, found by first moments of length, area, or volume divided by total length, area, or volume. For a uniform body it coincides with the center of gravity.

Related: Area moment of inertia, Friction
Friction

A tangential resistance force at contacting surfaces that opposes relative motion or its tendency. Static friction can reach a maximum proportional to the normal force; kinetic friction is roughly constant during sliding.

Related: Centroid, Equilibrium
Kinematics

The description of motion in terms of position, velocity, acceleration, and time, without reference to the forces causing the motion. Includes rectilinear, curvilinear, and rotational motion descriptions.

Related: Kinetics, Normal and tangential acceleration, Relative velocity
Kinetics

The study of motion accounting for the forces and moments that produce it, using Newton's second law, work-energy methods, or impulse-momentum methods to relate forces to changes in motion.

Related: Kinematics, Work-energy principle, Impulse-momentum principle
Normal and tangential acceleration

The two components of acceleration for a particle on a curved path. Tangential acceleration changes speed and equals the rate of change of velocity magnitude; normal acceleration changes direction and equals speed squared divided by radius of curvature.

Related: Kinematics, Centripetal acceleration
Centripetal acceleration

The inward-directed acceleration of a body moving on a circular path at constant speed, of magnitude speed squared divided by path radius. It arises from a net inward force such as tension or gravity.

Related: Normal and tangential acceleration, Kinetics
Relative velocity

The velocity of one body as observed from a moving reference frame attached to another body, equal to the vector difference of their absolute velocities. Essential for analyzing connected or contacting moving parts.

Related: Kinematics, Instantaneous center of zero velocity
Instantaneous center of zero velocity

For a rigid body in planar motion, the point about which the body appears to rotate at a given instant, having zero velocity at that moment. Locating it lets you relate velocities of points through angular velocity.

Related: Relative velocity, Kinematics
Work-energy principle

A statement that the net work done by all forces on a body equals its change in kinetic energy. Useful when forces vary with position or when time is unknown but displacement is known.

Related: Kinetics, Impulse-momentum principle
Impulse-momentum principle

A statement that the linear impulse of the net force over a time interval equals the change in linear momentum of the body. Useful when forces act over short times or when displacement is unknown.

Related: Work-energy principle, Kinetics
Mass moment of inertia

A measure of a body's resistance to angular acceleration about a specified axis, equal to the integral of mass times squared distance from the axis. Depends on the axis location and mass distribution.

Related: Radius of gyration, Parallel axis theorem
Radius of gyration

The distance from an axis at which a body's entire mass could be concentrated to give the same moment of inertia about that axis. Equals the square root of moment of inertia divided by mass.

Related: Mass moment of inertia, Parallel axis theorem
Parallel axis theorem

A relation giving the moment of inertia about any axis parallel to an axis through the centroid: the centroidal value plus mass (or area) times the squared distance between the axes.

Related: Mass moment of inertia, Area moment of inertia
Area moment of inertia

A geometric property of a cross section equal to the integral of squared distance from a reference axis over the area, measuring resistance to bending. Often called second moment of area.

Related: Parallel axis theorem, Section modulus
Section modulus

A cross-sectional property equal to the area moment of inertia about the centroidal axis divided by the distance from that axis to the extreme fiber. Used to compute maximum bending stress.

Related: Area moment of inertia, Bending stress
Bending stress

Normal stress in a beam caused by an internal bending moment, distributed linearly from zero at the neutral axis to a maximum at the extreme fiber. Computed as moment times distance from neutral axis divided by moment of inertia.

Related: Section modulus, Neutral axis, Shear stress
Neutral axis

The line in a beam cross section where bending stress is zero and which passes through the section centroid for elastic bending. Fibers on one side are in tension, the other in compression.

Related: Bending stress, Centroid
Shear stress

Stress acting parallel to a material surface, arising from transverse shear forces, torsion, or direct shear. In beams it is largest at the neutral axis and zero at the free surfaces for transverse loading.

Related: Bending stress, Torsion
Torsion

Twisting of a member caused by an applied torque about its longitudinal axis. Shear stress varies linearly with radial distance from the axis and is largest at the outer surface for a circular shaft.

Related: Shear stress, Polar moment of inertia
Polar moment of inertia

A cross-sectional property equal to the integral of squared radial distance from an axis over the area, measuring resistance to torsion. For a circular section it equals the sum of two perpendicular area moments of inertia.

Related: Torsion, Area moment of inertia
Stress-strain diagram

A plot of engineering stress versus engineering strain from a tension test, revealing elastic modulus, yield strength, ultimate strength, and ductility. The elastic region is linear for many metals up to the proportional limit.

Related: Hooke's law, Yield strength, Poisson's ratio
Hooke's law

The linear relation between stress and strain in the elastic range, with the constant of proportionality being the elastic modulus in tension or the shear modulus in shear. Valid only below the proportional limit.

Related: Stress-strain diagram, Poisson's ratio
Yield strength

The stress at which a material begins to deform permanently, often defined by a 0.2 percent offset method for metals lacking a distinct yield point. A key allowable-stress basis in design.

Related: Stress-strain diagram, Factor of safety
Poisson's ratio

The negative ratio of lateral strain to axial strain for a material under uniaxial loading. Typical metals fall near 0.3; the value approaches 0.5 for nearly incompressible materials such as rubber.

Related: Hooke's law, Stress-strain diagram
Factor of safety

The ratio of a material's failure-level stress to the allowable working stress, or of failure load to design load. It accounts for uncertainty in loads, material properties, and analysis methods.

Related: Yield strength, Professional responsibility
Professional responsibility

An engineer's duty to hold public safety, health, and welfare paramount, practice only within competence, be objective and truthful, and avoid conflicts of interest. Codified in many engineering society codes of ethics.

Related: Conflict of interest, Seal and signature, Factor of safety
Conflict of interest

A situation in which personal, financial, or other interests could improperly influence professional judgment. Engineers must disclose such situations and remove or manage the influence before acting.

Related: Professional responsibility, Seal and signature
Seal and signature

The licensed engineer's formal certification that work was performed under their responsible charge and meets applicable standards. Applying a seal to work outside one's competence or control is an ethics violation.

Related: Professional responsibility, Conflict of interest
Time value of money

The principle that a sum of money available today is worth more than the same sum later because it can earn interest. Basis for comparing cash flows occurring at different times.

Related: Present worth, Compound interest, Net present value
Compound interest

Interest computed on both the original principal and previously accumulated interest, so the balance grows geometrically over time. The effective annual rate exceeds the nominal rate when compounding occurs more than once per year.

Related: Time value of money, Present worth
Present worth

The equivalent value today of a future cash flow or series of cash flows, found by discounting each amount at a chosen interest rate. Used to compare alternatives on a common time basis.

Related: Net present value, Time value of money
Net present value

The sum of discounted cash inflows minus discounted cash outflows for a project at a specified rate. A positive value indicates the project earns more than the required rate of return.

Related: Present worth, Internal rate of return
Internal rate of return

The interest rate at which a project's net present value equals zero, making discounted benefits equal discounted costs. Compared against a minimum attractive rate of return to accept or reject a project.

Related: Net present value, Present worth
Depreciation

The systematic allocation of a tangible asset's cost over its useful life for accounting or tax purposes, such as straight-line or declining-balance methods. It is not a cash flow itself.

Related: Time value of money, Net present value
Mean and standard deviation

The mean is the arithmetic average of a data set; the standard deviation measures typical spread about that mean as the square root of variance. Together they describe the center and dispersion of a distribution.

Related: Normal distribution, Variance, Confidence interval
Normal distribution

A symmetric, bell-shaped continuous probability distribution defined by its mean and standard deviation. About 68 percent of values fall within one standard deviation of the mean and about 95 percent within two.

Related: Mean and standard deviation, Central limit theorem, Confidence interval
Central limit theorem

A result stating that the sampling distribution of the sample mean approaches a normal distribution as sample size grows, regardless of the population's shape, provided observations are independent and variance is finite.

Related: Normal distribution, Confidence interval
Confidence interval

A range of values, computed from sample data, that is expected to contain an unknown population parameter with a stated probability over repeated sampling. Width shrinks as sample size or confidence level changes.

Related: Central limit theorem, Hypothesis test
Hypothesis test

A procedure comparing sample evidence against a null hypothesis using a test statistic and a chosen significance level. A p-value below the significance level leads to rejecting the null hypothesis.

Related: Confidence interval, Type I and Type II error
Type I and Type II error

In hypothesis testing, a Type I error rejects a true null hypothesis, while a Type II error fails to reject a false null hypothesis. Their probabilities trade off against each other for a fixed sample size.

Related: Hypothesis test, Confidence interval
Permutation and combination

Counting rules for selecting items from a group. Permutations count arrangements where order matters; combinations count selections where order does not, and are always fewer for the same group size.

Related: Probability rules, Binomial distribution
Probability rules

Basic relations for combining event probabilities, including the addition rule for unions and the multiplication rule for intersections. Mutually exclusive events cannot occur together; independent events do not affect each other's probability.

Related: Permutation and combination, Binomial distribution
Binomial distribution

The probability distribution of the number of successes in a fixed number of independent trials, each with the same success probability. Defined by trial count and success probability.

Related: Probability rules, Normal distribution
Derivative

The instantaneous rate of change of a function with respect to a variable, interpreted geometrically as the slope of the tangent line. Used to find maxima, minima, and rates in engineering models.

Related: Integral, Optimization
Integral

The accumulation of a function over an interval, interpreted as signed area under a curve. The definite integral gives totals such as work, mass, or centroid coordinates from distributed quantities.

Related: Derivative, Centroid
Optimization

The process of finding the input values that maximize or minimize a function, typically by setting its derivative to zero and checking second-derivative or boundary conditions for the type of extremum.

Related: Derivative, Linear regression
Linear regression

Fitting a straight line to paired data by least squares, minimizing the sum of squared vertical deviations. The slope estimates change in the response per unit change in the predictor.

Related: Optimization, Mean and standard deviation

FE Mechanical study plan

8 weeks · About 6 hours per week

Week 1

Statics & Mechanics of Materials

  • Resolve 2D particle and rigid-body equilibrium problems by drawing complete free-body diagrams and writing all three equilibrium equations before solving

  • Compute internal axial force, shear, and bending moment at any section of a beam and draw the shear and moment diagrams from those equations

  • Calculate centroid and area moment of inertia for composite sections using the parallel-axis theorem

  • Build a one-page equation sheet for statics and section properties from memory, then verify it against a reference text

Your checkpoint

A worked notebook of 25 statics and section-property problems, each with a free-body diagram and a shear/moment diagram, scored against your own answer key at 85% or better

Week 2

Mechanics of Materials & Statics

  • Compute normal and shear stress in axial, torsional, and bending members and identify the location of maximum stress in each case

  • Apply Mohr's circle to convert a given state of stress into principal stresses and maximum shear stress

  • Determine beam deflection for at least two standard load cases using superposition

  • Analyze a statically indeterminate axial member by combining compatibility and equilibrium equations

  • Diagnose column buckling load with Euler's formula and state when the slenderness ratio makes it invalid

Your checkpoint

A timed 20-question mechanics-of-materials mock set completed in 50 minutes with every wrong answer rewritten as a corrected worked solution

Week 3

Dynamics & Statics

  • Solve projectile and curvilinear motion problems by separating velocity and acceleration into components with consistent sign conventions

  • Apply Newton's second law in normal-tangential and polar coordinates to bodies on curved paths

  • Use work-energy and impulse-momentum methods and justify choosing one over the other for a given problem

  • Analyze rigid-body rotation and rolling without slipping, including relative-velocity and relative-acceleration relations between points

  • Set up and solve a two-body connected-motion problem such as a pulley with hanging masses

Your checkpoint

A 15-problem dynamics set, each solution labeled with the method chosen (Newton, work-energy, or impulse-momentum) and a one-sentence justification for that choice

Week 4

Dynamics & Mechanics of Materials

  • Solve combined loading problems that superimpose axial, bending, and torsional stress at a critical point

  • Analyze a mass-spring-damper system for natural frequency, damping ratio, and free-vibration response

  • Compute fatigue life indicators for a member under cyclic loading using stress amplitude and mean stress

  • Review all statics, dynamics, and mechanics mistakes logged in weeks 1-3 and re-solve each one cold

Your checkpoint

A cumulative 30-question mock over domains 5, 6, and 7 completed in 75 minutes with a written error log categorizing each miss as concept, setup, or arithmetic

Week 5

Mathematics & Probability and Statistics

  • Differentiate and integrate polynomial, exponential, trigonometric, and logarithmic functions as they appear in rate and accumulation problems

  • Compute partial derivatives and use them to find maxima and minima of a two-variable function

  • Evaluate definite integrals numerically with the trapezoidal rule and check the result against the analytic value

  • Compute descriptive statistics including mean, standard deviation, and median from a raw data set and interpret the spread

  • Apply the normal and binomial distributions to compute probabilities for stated engineering scenarios

Your checkpoint

A formula card covering calculus and statistics rules plus 20 worked problems, with each calculus answer verified by an independent numerical check

Week 6

Probability and Statistics & Engineering Economics

  • Construct confidence intervals for a mean and state how sample size changes the interval width

  • Perform a one-sample hypothesis test and state the conclusion in the language of the problem, not just the p-value

  • Build a linear least-squares fit for paired data and interpret the slope and coefficient of determination

  • Convert between present worth, future worth, and uniform annual series using the standard interest factor notation

  • Compare alternatives with present worth, annual worth, and rate-of-return methods and identify when the comparison is invalid

Your checkpoint

A spreadsheet model that solves three engineering-economics alternatives and one regression problem, with a written paragraph explaining which alternative is selected and why

Week 7

Engineering Economics & Ethics and Professional Practice

  • Compute depreciation, book value, and after-tax cash flow for a capital purchase under a stated depreciation method

  • Perform a break-even and sensitivity analysis and identify the variable that most changes the decision

  • Apply the order-of-magnitude and unit-consistency checks to flag implausible answers on practice problems

  • Explain the standard canons of professional ethics and apply them to a conflict-of-interest and a public-safety scenario

  • Identify the correct professional response when a supervisor directs an engineer to sign off on work that does not meet code

Your checkpoint

A written ethics and economics portfolio: two scenario responses of 150 words each plus three fully worked economics problems with cash-flow diagrams

Week 8

Mathematics & Probability and Statistics & Ethics and Professional Practice & Engineering Economics & Statics & Dynamics & Mechanics of Materials

  • Complete two full-length timed practice exams under exam conditions and record per-domain accuracy

  • Re-drive every missed concept from the error logs into a corrected worked solution without notes

  • Memorize and reproduce the complete equation sheet from memory within 20 minutes

  • Finalize a one-page test-day strategy covering time allocation, calculator use, and the order in which to attempt problems

  • Verify reference materials, calculator model, and identification requirements against the current exam candidate agreement

Your checkpoint

A final readiness report showing per-domain accuracy above 70% on both practice exams and a completed one-page test-day strategy sheet

Milestones

Week 2: Score 75% or better on a self-made 20-question mechanics-of-materials quiz taken closed-book, and confirm every statics problem in the week 1 notebook can be re-solved without referencing the original solution

Week 4: Score 70% or better on the cumulative 30-question mock for domains 5, 6, and 7, and show that no error-log category accounts for more than 40% of the misses

Week 6: Complete the economics spreadsheet model with all three alternatives correctly ranked and the regression slope within 5% of an independent hand calculation

Week 8: Score 70% or better in every one of the seven domains across two full-length timed practice exams

FE Mechanical exam day

Your checklist

Government-issued photo ID

Bring the exact form of ID the test provider requires - typically a current, unexpired government-issued photo ID with your signature. The name must match your registration. Confirm with the provider which ID types are accepted and whether a secondary ID is needed; do not assume a student ID or expired document will work. (needs_review: exact accepted ID list varies by provider and test center.)

Admission or scheduling confirmation

Print or save your appointment confirmation showing your name, exam name (FE Mechanical), date, time, and test-center address or online-proctoring link. Some centers check this at the door. Confirm with the provider whether a printed copy is required or a digital copy is acceptable.

Know your approved reference material policy

The FE exam supplies a searchable electronic reference handbook on the testing computer. Do not bring your own formula sheets, notes, or bound references unless the provider explicitly allows them. Confirm with the provider what, if anything, you may bring and what is provided on-screen.

Approved calculator only

Bring only a calculator model the provider has approved for the FE exam. Know your model's functions cold before test day. Confirm with the provider the current approved-model list and whether the testing computer also offers an on-screen calculator.

Test-center logistics: arrival time and location

Arrive earlier than your appointment - many centers ask for 15–30 minutes to allow check-in, ID verification, and a security scan. Map the route and parking in advance. Confirm with the provider the exact arrival window and check-in cut-off.

Personal-item and storage plan

Expect a secure locker or designated area for bags, phones, and watches. Plan to travel light and leave prohibited items (phones, smartwatches, notes) secured. Confirm with the provider what is allowed at your seat versus stored.

Breaks and timing plan

Know how the exam clock and any scheduled or optional breaks work, and whether the clock pauses during breaks. Build a rough time budget per section. Confirm with the provider the break policy and whether unscheduled breaks count against your time.

Rest, food, and hydration the day before

Sleep on a normal schedule, eat a normal breakfast, and avoid trying new caffeine levels on test day. Bring water and a snack only if the provider allows them in the waiting area or during breaks.

Practice with the on-screen tools

Before test day, practice using the on-screen reference handbook, calculator, flag-for-review, and navigation tools in a timed practice setting. Familiarity with the interface saves minutes during the exam.

Scratch-work and answer-entry strategy

Decide in advance how you will handle scratch work and multiple-choice versus numeric-entry items - for example, write given values and units first, solve symbolically, then substitute. Confirm with the provider what scratch materials are supplied or permitted.

Review the scoring and pass/fail basis

Understand that the FE is scored on a pass/fail basis against a criterion-referenced standard, not a fixed percentage, and that results are typically reported after the exam rather than on the spot. Confirm with the provider the current reporting timeline and score-report details. (needs_review: reporting timeline and exact scoring method should be verified with the provider.)

Emergency and reschedule plan

Know the provider's policy on late arrival, illness, and rescheduling, and save the provider's contact number. Confirm with the provider the reschedule window and any fees before test day.

Plan the day

Final 72 hours

Stop learning new topics. Do one or two timed practice sessions under real conditions using the on-screen reference handbook and approved calculator, then review only your error patterns. Re-read your personal formula and unit-conversion summary. Confirm your appointment time, address or proctoring link, and ID requirements. Pack your ID and calculator and lay out clothes. Protect sleep: keep bedtimes normal rather than cramming late.

24 hours before

Do a light review of high-yield areas and your weakest two or three topics - no full-length mock exams. Verify the route, parking, and travel time, and set two alarms. Charge devices and confirm any online-proctoring software is installed and tested if applicable. Eat a normal dinner, avoid alcohol, and go to bed at your usual time. Prepare a snack and water only if the provider permits them.

Morning of the exam

Eat a normal breakfast and limit caffeine to your usual amount. Leave with extra time to spare and arrive within the provider's check-in window. Bring your ID, confirmation, and approved calculator only; store everything else as directed. Do a short, calm warm-up - a few unit conversions or a key formula - rather than a frantic review. Use the restroom before check-in.

During the test

Read each item fully and note what is being asked and the units required. Work the easy items first, flag hard ones, and return to them; never leave a multiple-choice item blank. Show organized scratch work with units so you can catch errors. Watch the clock and reserve time to revisit flagged items. Take scheduled breaks if they help you reset, and return promptly. For numeric-entry items, check magnitude and units before submitting. If you finish early, review flagged items rather than second-guessing confident answers.

Rules to check

  • Bring valid, unexpired government-issued photo ID whose name matches your registration exactly; confirm the accepted ID types with the provider before test day.

  • Bring only an approved calculator and permitted items. Phones, smartwatches, notes, and other prohibited items must be stored as directed; confirm the full prohibited-items list with the provider.

  • Follow all check-in and security procedures, including any ID verification, photograph, or security scan. Refusal to comply may result in being turned away; confirm the procedure with the provider.

  • Know the break policy before you start: when breaks are available, whether the clock pauses, and whether unscheduled breaks count against your time. Confirm these details with the provider.

  • The exam is scored pass/fail against a criterion-referenced standard rather than a fixed percentage, and results are typically reported after the exam. Confirm the current scoring and reporting policy with the provider. (needs_review: verify scoring method and reporting timeline.)

  • Do not attempt to remove, photograph, or reproduce exam content or the on-screen reference handbook; treat all exam material as confidential and follow the provider's candidate agreement.

  • If you arrive late, fall ill, or cannot test, contact the provider immediately and follow its reschedule or cancellation policy; confirm the window and any fees in advance.

  • Answer every item - there is no penalty described for guessing on multiple-choice items, so eliminate options and commit to an answer rather than leaving blanks. Confirm the current exam rules with the provider.

FE Mechanical FAQ

How many FE Mechanical practice questions are available?

The practice set has 200 FE Mechanical questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many FE Mechanical flashcards are available?

The flashcard set has 34 FE Mechanical cards. Each card shows the term and its definition.

Which topics does the FE Mechanical study material cover?

The FE Mechanical study material has 7 sections, including Mathematics, Probability and Statistics, and Ethics and Professional Practice.

What format facts does the catalog list for the FE Mechanical exam?

The catalog lists a duration of 320 minutes and these item types: computer-based exam and multiple choice for the FE Mechanical exam.