FE Electrical & Computer Practice Test

Fundamentals of Engineering (FE) exam

FE Electrical & Computer overview

  • 200 practice questions
  • 32 flashcards
  • 3 study guide topics
  • 39 key terms

What you'll study

  • Electrical and Computer: Computer Engineering
  • Electrical and Computer: Electrical and Electronics
  • Electrical and Computer: Power

The Fundamentals of Engineering (FE) exam is generally the first step in the process of becoming a licensed professional engineer (P.E.). NCEES describes it as designed for recent graduates and students who are close to finishing an undergraduate engineering degree from an EAC/ABET-accredited program. It is a computer-based exam administered year-round at NCEES-approved Pearson test centers, and the $225 exam fee is payable directly to NCEES. The FE exam includes 110 questions. The exam appointment time is 6 hours long and includes a nondisclosure agreement (2 minutes), a tutorial (8 minutes), the exam itself (5 hours and 20 minutes), and a scheduled break (25 minutes). The Electrical and Computer exam is offered in three disciplines: Computer Engineering; Electrical and Electronics; and Power. Results are typically available within 7–10 business days and are reported as pass or fail; if you fail, you receive a diagnostic report showing your performance for each of the major topics covered on the exam. Because the exam is administered year-round, you can register and schedule through your MyNCEES account and choose from available exam dates and locations. Prepare by working through the exam specifications for your discipline, refreshing core analysis methods, and practicing timed problem sets under exam-like conditions. This page is independent study material and is not affiliated with or endorsed by NCEES.

Common mistakes

On NCEES-supplied reference questions, the candidate recalculates a quantity from first principles using a memorized formula instead of reading the value or relationship directly from the provided tables (unit conversions, wire ampacity, conduit fill, Laplace transforms).

Candidates treat the exam as closed-book and drill formulas from textbooks, so under time pressure they reconstruct a conversion factor from memory rather than flipping to the supplied table, and a misremembered factor silently corrupts every downstream step.

What to do instead

During practice, work every problem with the actual NCEES reference handbook open beside you and mark which table you used. Build a personal index of the handbook sections you touch most (conversions, motor tables, transform pairs) so lookup becomes a reflex rather than a last resort.

On per-unit and three-phase power problems, the candidate mixes line-to-line and line-to-neutral voltages, or forgets to convert the base impedance when changing the MVA base between transformer stages.

Per-unit work is taught with formulas that hide the sqrt(3) and the base-change ratio; candidates memorize S = VI without tracking whether V is line or phase, and the arithmetic looks plausible either way so the error goes undetected.

What to do instead

Adopt a fixed written template for every per-unit problem: state S_base, V_base at each voltage level, then Z_base = V_base^2 / S_base, then convert each element with Z_pu,new = Z_pu,old * (S_new/S_old) * (V_old/V_new)^2. Do ten mixed problems with the template until the base-change step is automatic.

The candidate solves a circuit problem by the first method that comes to mind (nodal analysis on a bridge, mesh analysis on a circuit with a current source in the shared branch) and burns eight to ten minutes on algebra instead of switching to superposition, Thevenin, or a source transformation.

Coursework rewards grinding one technique to completion, so candidates commit to a method before scanning the topology; the exam's time budget (roughly three minutes per question average) makes a wrong method choice fatal even when the physics is understood.

What to do instead

Before writing equations, spend fifteen seconds classifying the circuit: count nodes versus meshes, note current sources, dependent sources, and whether only one element's response is asked. Practice a drill where the same circuit is solved three ways and you time each, so you learn which topology favors which method.

On digital logic and state-machine questions, the candidate derives a next-state or output expression from the schematic by inspection and does not verify it against a truth table, so a single missed inverted input or an active-low enable flips the answer.

Boolean simplification by eye is fast and usually right, which trains overconfidence; active-low signals and enable pins are the exact places where inspection fails, and the candidate has no independent check.

What to do instead

For any combinational or sequential block, write the truth table or state table first, then read the answer off the table. For sequential logic, explicitly list present state, input, next state, output for each row before choosing an option.

The candidate answers a motor question using the nameplate full-load current and horsepower directly, skipping the distinction between input power, output mechanical power, and efficiency, and ignoring service factor and the 125% conductor sizing rule.

Motor problems look like simple P = VI arithmetic, so candidates plug nameplate values into the wrong side of the efficiency equation; the National Electrical Code sizing multipliers are learned as trivia rather than as a workflow.

What to do instead

Use a fixed chain for every motor problem: output horsepower to watts, divide by efficiency to get input power, then compute current from voltage and power factor, then apply the applicable 125% or 430% multiplier for the question asked. Practice separating 'what the motor delivers' from 'what the feeder must carry'.

On electronics questions involving diodes, transistors, or op-amps, the candidate assumes an ideal device and ignores the region of operation, so a BJT assumed in forward-active is actually saturated or an op-amp output is driven past its rail.

Ideal-device assumptions are taught first and stick; checking the region of operation requires a second pass that candidates skip when they get a clean number from the ideal model.

What to do instead

Always finish with a consistency check: for a BJT confirm V_CE > 0.2 V (or the stated saturation voltage) and V_BE forward biased; for an op-amp confirm the required output lies within the supply rails; for a diode confirm the assumed on/off state matches the resulting current direction. Make the check a written step, not a mental one.

The candidate treats a control-systems question as pure algebra, computing a transfer function or steady-state error without checking stability, or reading a Bode plot's gain margin and phase margin off the wrong crossover frequency.

Laplace manipulation feels like the whole task, so stability criteria and margin definitions are treated as optional; gain margin is measured at the phase crossover and phase margin at the gain crossover, and candidates routinely swap them.

What to do instead

For every control problem, state which crossover you are using before reading a value: gain margin at the frequency where phase is -180 degrees, phase margin at the frequency where magnitude is 0 dB. Confirm stability with a Routh-Hurwitz check or by counting right-half-plane poles when a closed-loop transfer function is given.

On power-system protection and fault questions, the candidate computes fault current without establishing the system impedance path (transformer, line, source) in per unit, or picks a protective device setting without checking coordination with the upstream device.

Fault analysis is often studied as a formula (I = V/Z) divorced from the one-line diagram, and coordination is studied as a definition rather than as a time-current curve exercise, so the candidate never builds the habit of tracing the path.

What to do instead

Redraw the one-line diagram for every fault problem, mark each impedance in per unit on a common base, and reduce series and parallel combinations explicitly. For coordination questions, sketch the time-current curves and verify the downstream device clears before the upstream device trips at the fault current.

On computer-engineering questions about memory hierarchy, pipelining, or instruction timing, the candidate computes average access time or speedup using only the hit ratio and hit time, omitting the miss penalty, or applies the pipeline speedup formula without accounting for stalls and the fill/drain overhead.

The simplified formulas are memorable and produce a number quickly; the full expressions require an extra term that is easy to drop, and no sanity check reveals the omission.

What to do instead

Write the full expression before substituting: average access time = hit time + miss rate x miss penalty; pipeline speedup = number of stages / (1 + stall cycles per instruction). Then ask whether the answer is bounded sensibly (speedup cannot exceed the number of stages; average access time cannot be below hit time).

The candidate spends disproportionate time on one hard question, then rushes the remaining questions and makes transcription errors on answers already solved on scratch paper.

The exam is scored on total correct answers with no penalty for guessing, but candidates carry over a habit from graded coursework of needing to finish every problem, so they sacrifice many easy points to chase one hard one.

What to do instead

Set a hard per-question cap (about three minutes) in practice, flag and move on when it is hit, and reserve the final fifteen minutes for flagged items and for transferring answers carefully. Simulate this with full-length timed practice exams so the flag-and-return habit is trained, not improvised.

Exam requirements can change. Confirm current details with the exam provider.

FE Electrical & Computer practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Electrical and Computer: Computer Engineering

    In two's-complement arithmetic with 8-bit registers, what is the decimal value of the bit pattern 1111 0110?

    1. -10 Correct answer.
    2. -118
    3. 246
    4. -9

    Explanation

    The leading bit is 1, so the value is negative. Invert all bits (0000 1001) and add one to get 0000 1010, which is 10, so the value is -10. Equivalently, 1111 0110 = -128 + 64 + 32 + 16 + 4 + 2 = -10.

  2. Question 2Electrical and Computer: Computer Engineering

    How many select (control) lines does a 32-to-1 multiplexer require?

    1. 4
    2. 5 Correct answer.
    3. 32
    4. 6

    Explanation

    An N-to-1 multiplexer needs ceil(log2 N) select lines because the select code must uniquely address each of the N data inputs. For N = 32, log2(32) = 5 select lines.

  3. Question 3Electrical and Computer: Computer Engineering

    A 4-bit ripple-carry adder is built from four full adders. What is its main performance limitation compared with a carry-lookahead adder?

    1. It cannot add two's-complement negative numbers correctly.
    2. It consumes more static power because it uses more transistors than a lookahead adder.
    3. It requires a clock signal to sequence the carry between stages.
    4. The carry must propagate serially through each stage, so the worst-case delay grows with the number of bits. Correct answer.

    Explanation

    In a ripple-carry adder each full adder must wait for the carry-out of the previous stage, so the critical path delay scales linearly with bit width. Carry-lookahead logic computes group generate and propagate signals to shorten that path. A ripple adder is combinational and handles two's-complement operands correctly.

  4. Question 4Electrical and Computer: Computer Engineering

    Which statement describes a key property of SRAM cells used in CPU register files and caches?

    1. They retain data without power because they use floating-gate transistors.
    2. They are programmed once at manufacture and cannot be rewritten.
    3. They store a bit as a cross-coupled latch that holds state as long as power is applied. Correct answer.
    4. They store a bit as charge on a capacitor that must be periodically refreshed.

    Explanation

    An SRAM bit cell is a bistable latch, typically six transistors, that holds its state statically while powered. Because the state is actively latched, no refresh is required, which makes SRAM fast but area-expensive compared with DRAM.

  5. Question 5Electrical and Computer: Computer Engineering

    In the IEEE 754 single-precision format, how many bits are allocated to the exponent and to the fraction (significand) field?

    1. 7 exponent bits and 24 fraction bits
    2. 8 exponent bits and 24 fraction bits
    3. 11 exponent bits and 52 fraction bits
    4. 8 exponent bits and 23 fraction bits Correct answer.

    Explanation

    Single precision uses 1 sign bit, 8 exponent bits with a bias of 127, and 23 stored fraction bits. An implicit leading 1 adds one bit of effective precision, giving 24 significant bits total.

  6. Question 6Electrical and Computer: Computer Engineering

    What is the primary purpose of a cache memory in a computer system?

    1. To increase the total addressable memory space beyond the physical RAM size.
    2. To provide nonvolatile backup of main memory contents during power loss.
    3. To reduce the average time to access data by keeping recently used blocks close to the processor. Correct answer.
    4. To translate virtual addresses into physical addresses.

    Explanation

    Caches exploit temporal and spatial locality by holding recently referenced blocks in fast memory near the CPU, lowering average access latency. They are volatile and do not extend address space or perform address translation.

  7. Question 7Electrical and Computer: Computer Engineering

    Which protocol is most appropriate for connecting low-speed sensors on a shared two-wire bus where multiple devices are addressed by unique IDs?

    1. I2C Correct answer.
    2. USB
    3. PCIe
    4. SPI

    Explanation

    I2C uses two wires, SDA and SCL, with a clocked serial protocol and 7- or 10-bit device addressing, which suits many low-speed sensors sharing one bus. SPI needs separate chip-select lines per device, and PCIe and USB are higher-speed interfaces with more complex protocols.

  8. Question 8Electrical and Computer: Computer Engineering

    In a finite state machine, what distinguishes a Moore machine from a Mealy machine?

    1. Moore machines are asynchronous, while Mealy machines are synchronous.
    2. Moore machines have no state register, while Mealy machines do.
    3. Moore outputs depend on the current inputs only, while Mealy outputs depend on state only.
    4. Moore outputs depend only on the current state, while Mealy outputs depend on the current state and inputs. Correct answer.

    Explanation

    A Moore machine derives its outputs solely from the registered state, so outputs change only on state transitions. A Mealy machine combines current state and current inputs to form outputs, which can respond in the same cycle but may glitch.

  9. Question 9Electrical and Computer: Computer Engineering

    A synchronous counter is clocked at 50 MHz and has a terminal count of 249 (counts 0 through 249). What is the frequency of the terminal-count pulse?

    1. 250 kHz
    2. 2 MHz
    3. 200 kHz Correct answer.
    4. 500 kHz

    Explanation

    The counter has 250 states, so a terminal-count pulse occurs once every 250 clock cycles. The pulse frequency is 50 MHz / 250 = 200 kHz.

  10. Question 10Electrical and Computer: Computer Engineering

    A 4-bit synchronous binary counter using T flip-flops is at state 1011. What is the next state after one clock edge?

    1. 1100 Correct answer.
    2. 1010
    3. 1101
    4. 0100

    Explanation

    The binary value 1011 equals 11, so the next count is 12, which is 1100 in four bits. In a T flip-flop counter, the LSB toggles every cycle and each higher bit toggles when all lower bits are 1, which matches this increment.

  11. Question 11Electrical and Computer: Computer Engineering

    A direct-mapped cache has 256 lines and a block size of 16 bytes. To which cache line does the byte address 0x0A3C map?

    1. Line 163 with block offset 12
    2. Line 60
    3. Line 163 Correct answer.
    4. Line 43

    Explanation

    The block offset uses log2(16) = 4 bits, so the block number is 0x0A3C >> 4 = 0xA3 = 163. With 256 lines, the line index is 163 mod 256 = 163. The offset within the block is 0x0A3C & 0xF = 12, but the question asks for the line.

  12. Question 12Electrical and Computer: Computer Engineering

    A direct-mapped cache has a hit time of 1 cycle and a miss penalty of 50 cycles. If the miss rate is 4%, what is the average memory access time?

    1. 51 cycles
    2. 2 cycles
    3. 2.5 cycles
    4. 3 cycles Correct answer.

    Explanation

    Average access time equals hit time plus miss rate times miss penalty: 1 + 0.04 x 50 = 1 + 2 = 3 cycles. This standard formula weights the full miss penalty by the fraction of accesses that miss.

  13. Question 13Electrical and Computer: Computer Engineering

    A pipeline has five stages with stage delays of 2 ns, 3 ns, 2 ns, 4 ns, and 2 ns. Ignoring register overhead, what is the steady-state throughput of the pipeline?

    1. One instruction every 2.6 ns
    2. One instruction every 13 ns
    3. One instruction every 2 ns
    4. One instruction every 4 ns Correct answer.

    Explanation

    In steady state the clock period is set by the slowest stage, which is 4 ns here, so one instruction completes per 4 ns. The sum of stage delays (13 ns) is the non-pipelined latency, not the throughput period.

  14. Question 14Electrical and Computer: Computer Engineering

    A 16-bit ADC has a full-scale input range of 5 V. What is the approximate resolution (LSB size) in volts?

    1. 38 microvolts
    2. 305 microvolts
    3. 76 microvolts Correct answer.
    4. 5 millivolts

    Explanation

    The LSB size equals full-scale range divided by 2^16 - 1, the number of steps. That is 5 V / 65535, which is about 76 microvolts.

  15. Question 15Electrical and Computer: Computer Engineering

    A synchronous sequential circuit uses a single clock and positive-edge-triggered flip-flops. Which condition must hold for reliable operation?

    1. All flip-flops must have identical propagation delays to avoid race conditions.
    2. Input data must be stable for the setup time before the clock edge and the hold time after it. Correct answer.
    3. The clock frequency must be below the combinational logic delay of the longest path.
    4. The clock must have a duty cycle of exactly 50% for the flip-flops to toggle.

    Explanation

    Setup and hold windows around the active clock edge guarantee that the flip-flop samples a stable value. Violating either window risks metastability or incorrect data capture. Duty cycle and matched delays are not strict requirements for correct edge-triggered operation.

  16. Question 16Electrical and Computer: Computer Engineering

    A Mealy FSM detects the overlapping sequence 101 on a serial input. The machine is in the state representing a detected prefix '10' and the next input bit is 1. What output is produced and what is the appropriate next state?

    1. Output 1 and return to the start state, since the trailing 1 can begin a new 101. Correct answer.
    2. Output 1 and go to a state meaning '10' again.
    3. Output 1 and go to a state meaning '11'.
    4. Output 0 and return to the start state.

    Explanation

    Seeing 1 after prefix '10' completes 101, so a Mealy machine asserts the output in that transition. For overlapping detection, the final 1 also serves as the first bit of a possible new match, so the machine returns to the start state.

  17. Question 17Electrical and Computer: Computer Engineering

    A byte-addressable memory has 20 address lines. What is its total addressable capacity?

    1. 512 KiB
    2. 2 MiB
    3. 1 MB as 10^6 bytes exactly
    4. 1 MiB Correct answer.

    Explanation

    Twenty address lines select 2^20 = 1,048,576 distinct byte locations, which is 1 MiB. The distinction from 10^6 bytes matters because memory capacity uses powers of two.

  18. Question 18Electrical and Computer: Computer Engineering

    A processor executes a program with 2 x 10^6 instructions. The instruction mix requires an average of 3.5 cycles per instruction, and the clock is 1 GHz. What is the execution time?

    1. 3.5 ms
    2. 2 ms
    3. 14 ms
    4. 7 ms Correct answer.

    Explanation

    Total cycles equal instructions times cycles per instruction: 2 x 10^6 x 3.5 = 7 x 10^6 cycles. At 1 GHz, each cycle is 1 ns, so the time is 7 x 10^6 ns, which is 7 ms.

  19. Question 19Electrical and Computer: Computer Engineering

    A cache uses LRU replacement and a set contains four ways with recency order A (most recent), B, C, D (least recent). A miss occurs and the new block is placed in the set. Which block is evicted, and what is the new recency order?

    1. A is evicted; the new block becomes most recent, giving order New, B, C, D.
    2. D is evicted; the new block becomes most recent, giving order New, A, B, C. Correct answer.
    3. B is evicted; the new block becomes most recent, giving order New, A, C, D.
    4. D is evicted; the new block becomes least recent, giving order A, B, C, New.

    Explanation

    LRU evicts the least recently used block, which is D in this set. The newly filled block is the most recently used, so it moves to the front and the others shift down, yielding New, A, B, C.

  20. Question 20Electrical and Computer: Computer Engineering

    A 4-bit DAC has a full-scale output of 15 V and a binary input of 1001. Assuming an ideal weighted-resistor DAC with LSB = 1 V, what is the output voltage?

    1. 8 V
    2. 15 V
    3. 10 V
    4. 9 V Correct answer.

    Explanation

    The input 1001 equals decimal 9, and with an LSB of 1 V the output is 9 V. The weighted-resistor network sums binary-weighted currents, so the output is proportional to the integer code.

  21. Question 21Electrical and Computer: Computer Engineering

    In a three-stage pipeline with no forwarding, an ALU result is needed by the immediately following instruction. How many stall cycles are typically inserted, and why?

    1. Zero cycles, because the register file writes and reads in the same cycle.
    2. Three cycles, because every pipeline stage must drain completely.
    3. Two cycles, because the result is not written until the end of the third stage and must be read after that. Correct answer.
    4. One cycle, because only the execute stage must complete.

    Explanation

    Without forwarding, a producer's result is available only after the write-back stage, while the consumer needs it in its decode/read stage. For a three-stage pipe where execute is stage 2 and write-back is stage 3, two stall cycles are inserted so the consumer reads the updated register.

  22. Question 22Electrical and Computer: Computer Engineering

    A synchronous design has a clock period of 10 ns, flip-flop clock-to-Q delay of 1 ns, combinational logic delay of 6 ns, setup time of 1 ns, and clock skew of 1 ns (capture clock arrives later). Does the path meet setup timing, and what is the slack?

    1. Yes; the slack is 1 ns, since required time is 10 + 1 and arrival is 1 + 6 + 1. Correct answer.
    2. Yes; the slack is 2 ns, since skew is ignored in setup analysis.
    3. No; the slack is -1 ns because skew reduces the available time.
    4. Yes; the slack is 3 ns, since only the logic delay matters.

    Explanation

    With capture clock arriving 1 ns later, the required time at the capture flop is 10 + 1 = 11 ns. The data arrival is clock-to-Q plus logic plus setup, 1 + 6 + 1 = 8 ns, so the slack is 11 - 8 = 3 ns. Note that positive capture-side skew increases the setup margin.

  23. Question 23Electrical and Computer: Computer Engineering

    A CPU uses a two-level cache hierarchy. L1 hit time is 1 cycle with a 10% miss rate; L2 hit time is 10 cycles with a 20% local miss rate; main memory access takes 100 cycles. What is the average memory access time?

    1. 3 cycles
    2. 12 cycles
    3. 4 cycles Correct answer.
    4. 11 cycles

    Explanation

    AMAT = L1 hit time + L1 miss rate x (L2 hit time + L2 miss rate x memory penalty) = 1 + 0.10 x (10 + 0.20 x 100) = 1 + 0.10 x 30 = 4 cycles.

  24. Question 24Electrical and Computer: Computer Engineering

    An FSM must detect the overlapping pattern 1101 on a serial input. After observing the prefix 110, the next input bit is 1. What is the correct next state for overlapping detection?

    1. A state representing the suffix '1'.
    2. A state representing the suffix '01'.
    3. A state representing the suffix '11'. Correct answer.
    4. A state representing the suffix '1101'.

    Explanation

    The observed stream ends in 1101, which completes the pattern, but for overlapping detection the machine must also retain the longest suffix that is a prefix of 1101. The suffix '11' is such a prefix, so the machine moves to that state.

  25. Question 25Electrical and Computer: Computer Engineering

    A 32-bit processor has a 4-way set-associative L1 cache with 64 KiB capacity and 64-byte blocks. How many sets does the cache contain?

    1. 64
    2. 256 Correct answer.
    3. 1024
    4. 4096

    Explanation

    The cache holds 64 KiB / 64 B = 1024 blocks. With 4 ways per set, the number of sets is 1024 / 4 = 256, and the set index uses log2(256) = 8 bits.

  26. Question 26Electrical and Computer: Computer Engineering

    In the IEEE 754 single-precision format, how many bits are allocated to the exponent field?

    1. 8 Correct answer.
    2. 7
    3. 10
    4. 11

    Explanation

    Single precision uses 1 sign bit, 8 exponent bits, and 23 fraction bits for a total of 32 bits. The exponent is stored in biased form with a bias of 127.

  27. Question 27Electrical and Computer: Computer Engineering

    Which logic gate family output is produced by the Boolean expression A'B + AB'?

    1. Exclusive-NOR
    2. Exclusive-OR Correct answer.
    3. NOR
    4. NAND

    Explanation

    The expression A'B + AB' is the canonical sum-of-products form of the XOR function, which is true when exactly one input is true. XNOR would add the AB and A'B' terms.

  28. Question 28Electrical and Computer: Computer Engineering

    A two-input AND gate drives a two-input OR gate, whose other input is C. Which expression describes the OR gate output?

    1. A + BC
    2. ABC
    3. AB + C Correct answer.
    4. (A + B)C

    Explanation

    The AND gate produces AB, and the OR gate combines that with C to yield AB + C. Operator precedence in Boolean algebra places AND before OR.

  29. Question 29Electrical and Computer: Computer Engineering

    In the context of computer architecture, what does the term 'von Neumann bottleneck' refer to?

    1. The delay introduced by the clock distribution network
    2. The limited bandwidth of the path between processor and memory Correct answer.
    3. The limited number of general-purpose registers
    4. The latency of the arithmetic logic unit

    Explanation

    In a von Neumann machine, instructions and data share a single memory path, so the processor can be starved waiting for memory. This throughput limitation is what the term names.

  30. Question 30Electrical and Computer: Computer Engineering

    Which number system representation stores the negative of a value by inverting every bit and adding one?

    1. Sign-magnitude
    2. Two's complement Correct answer.
    3. One's complement
    4. Excess-127 (biased)

    Explanation

    Two's complement negation is defined as the bitwise complement plus one, which gives a single representation for zero and a clean arithmetic range. One's complement only inverts the bits.

  31. Question 31Electrical and Computer: Computer Engineering

    Which memory type loses its stored contents when power is removed but offers the highest density and lowest cost per bit?

    1. Dynamic RAM Correct answer.
    2. Static RAM
    3. Flash memory
    4. Ferroelectric RAM

    Explanation

    DRAM stores each bit as charge on a capacitor, so it is volatile but very dense and inexpensive, which makes it the standard main memory technology. SRAM uses more transistors per bit and is costlier.

  32. Question 32Electrical and Computer: Computer Engineering

    Which addressing mode computes the effective address as the sum of a base register and a constant offset encoded in the instruction?

    1. Immediate
    2. PC-relative
    3. Register indirect
    4. Base-plus-displacement Correct answer.

    Explanation

    Base-plus-displacement adds a signed constant in the instruction to the contents of a base register to form the effective address. This supports array and structure access.

  33. Question 33Electrical and Computer: Computer Engineering

    A signal is transmitted over a channel that supports four distinct voltage levels. How many bits are carried by each symbol?

    1. 3
    2. 1
    3. 2 Correct answer.
    4. 4

    Explanation

    With M distinct signaling levels, each symbol conveys log2(M) bits, and log2(4) equals 2. So each symbol carries two bits.

  34. Question 34Electrical and Computer: Computer Engineering

    Which logic gate produces a HIGH output only when all of its inputs are HIGH?

    1. OR
    2. AND Correct answer.
    3. NOR
    4. XOR

    Explanation

    An AND gate outputs 1 only for the all-ones input combination, which is the definition of the AND function. Every other input pattern yields 0.

  35. Question 35Electrical and Computer: Computer Engineering

    A 16-bit register holds the value 0x00F0. What does this value represent in unsigned decimal?

    1. 240 Correct answer.
    2. 15
    3. 1920
    4. 255

    Explanation

    0x00F0 equals 15 times 16, because the hex digit F occupies the sixteens place. That product is 240.

  36. Question 36Electrical and Computer: Computer Engineering

    A Karnaugh map for a four-variable function has the minterms 0, 1, 2, 3, 8, 9, 10, and 11. Which simplified sum-of-products expression results?

    1. B' Correct answer.
    2. A'
    3. C'
    4. D'

    Explanation

    The listed minterms cover all cells where B equals 0, regardless of A, C, and D, so the function simplifies to B'. The two groups of four merge into one group of eight.

  37. Question 37Electrical and Computer: Computer Engineering

    An 8-bit two's complement register contains 0b11110110. What signed decimal value does it hold?

    1. 246
    2. -11
    3. -10 Correct answer.
    4. -9

    Explanation

    The leading bit is 1, so the value is negative. Inverting the bits gives 0b00001001 and adding one gives 0b00001010, which is 10, so the value is -10.

  38. Question 38Electrical and Computer: Computer Engineering

    A combinational circuit has three inputs and produces a 1 only when an odd number of inputs are 1. Which single gate implements this function?

    1. Three-input OR
    2. Three-input XOR Correct answer.
    3. Three-input NAND
    4. Three-input XNOR

    Explanation

    The XOR function is 1 when an odd number of its inputs are 1, and this property extends directly to the three-input case. The truth table has four minterms with ones.

  39. Question 39Electrical and Computer: Computer Engineering

    A JK flip-flop has J and K both tied HIGH and is clocked. What behavior does it exhibit?

    1. It toggles on each active clock edge Correct answer.
    2. It holds its current state
    3. It sets to 1 and stays there
    4. It resets to 0 and stays there

    Explanation

    With both J and K asserted, the JK flip-flop enters toggle mode and complements its output at each active edge. This is the basis for building ripple and synchronous counters.

  40. Question 40Electrical and Computer: Computer Engineering

    A synchronous circuit must count from 0 through 5 repeatedly. What is the minimum number of flip-flops required?

    1. 3 Correct answer.
    2. 2
    3. 6
    4. 4

    Explanation

    Six states require a state encoding with at least six codes, and two flip-flops provide only four. Three flip-flops provide eight codes, which is the smallest sufficient number.

  41. Question 41Electrical and Computer: Computer Engineering

    An instruction pipeline suffers a branch penalty of 3 cycles and executes 20% branch instructions with a 40% taken rate. What is the average cycles-per-instruction penalty from branches alone?

    1. 0.80
    2. 0.60
    3. 0.24 Correct answer.
    4. 0.12

    Explanation

    The penalty per instruction equals branch frequency times taken rate times penalty cycles: 0.20 x 0.40 x 3 = 0.24. This adds to the base CPI.

  42. Question 42Electrical and Computer: Computer Engineering

    A system uses Hamming code with 4 data bits. How many parity bits are needed to correct a single-bit error?

    1. 4
    2. 2
    3. 3 Correct answer.
    4. 5

    Explanation

    The Hamming condition requires 2^p >= m + p + 1, where m is 4. With p equal to 3, 8 >= 8 holds, so three parity bits suffice.

  43. Question 43Electrical and Computer: Computer Engineering

    Which statement correctly distinguishes a microprocessor from a microcontroller?

    1. A microcontroller cannot execute stored programs
    2. A microcontroller integrates CPU, memory, and peripherals on one chip Correct answer.
    3. A microprocessor is restricted to embedded control tasks
    4. A microprocessor always contains on-chip flash program memory

    Explanation

    A microcontroller is a complete system on a chip that includes the CPU along with RAM, nonvolatile program memory, and peripherals such as timers and serial ports. A microprocessor is typically just the CPU and needs external support chips.

  44. Question 44Electrical and Computer: Computer Engineering

    A memory system uses even parity. The byte 0b10110101 is transmitted. What is the correct parity bit?

    1. 2
    2. It cannot be determined
    3. 1 Correct answer.
    4. 0

    Explanation

    The byte contains five 1s, which is an odd count. Even parity requires the total number of 1s including the parity bit to be even, so the parity bit must be 1.

  45. Question 45Electrical and Computer: Computer Engineering

    A CPU has a 2 GHz clock and executes a program in 5 x 10^8 cycles. What is the execution time?

    1. 2.5 s
    2. 0.10 s
    3. 0.25 s Correct answer.
    4. 0.50 s

    Explanation

    Execution time equals cycles divided by clock frequency: 5 x 10^8 divided by 2 x 10^9 equals 0.25 seconds. The clock period is 0.5 ns.

  46. Question 46Electrical and Computer: Computer Engineering

    Which statement about a set-associative cache is correct when the associativity is increased while capacity and block size stay fixed?

    1. The hit time always decreases
    2. The number of sets decreases and conflict misses tend to fall Correct answer.
    3. The number of sets increases and conflict misses tend to rise
    4. The block size increases proportionally

    Explanation

    With fixed capacity and block size, raising associativity means fewer sets but more ways per set, so fewer blocks compete for the same set. This reduces conflict misses at the cost of more comparators and possibly longer hit time.

  47. Question 47Electrical and Computer: Computer Engineering

    A 4-bit ripple-carry adder adds 0b0111 and 0b0001. What are the 4-bit sum and the carry-out?

    1. Sum 1111, carry-out 0
    2. Sum 0110, carry-out 1
    3. Sum 1000, carry-out 1
    4. Sum 1000, carry-out 0 Correct answer.

    Explanation

    Seven plus one equals eight, which is 0b1000 in four bits, so the sum fits with no carry out of the most significant position. The carry propagates through all four stages but leaves the final sum bit at 1.

  48. Question 48Electrical and Computer: Computer Engineering

    A 32-bit processor uses 4-byte instructions and a byte-addressable memory. If the program counter holds 0x00001004 and the instruction uses PC-relative addressing with an offset of -4, what is the target address?

    1. 0x00001008
    2. 0x00001004
    3. 0x00001000 Correct answer.
    4. 0x00000FFC

    Explanation

    PC-relative addressing adds the offset to the program counter value, giving 0x00001004 plus (-4) equals 0x00001000. Whether the updated PC is used depends on the architecture, but here the stated PC is the base.

  49. Question 49Electrical and Computer: Computer Engineering

    A direct-mapped cache with 16 lines and 8-byte blocks receives the byte address 0x00C8. Which line does it map to?

    1. 25
    2. 8
    3. 12
    4. 9 Correct answer.

    Explanation

    The block number equals the address divided by the block size: 200 divided by 8 equals 25. The line index is the block number modulo the number of lines, so 25 modulo 16 equals 9.

  50. Question 50Electrical and Computer: Computer Engineering

    A sequential circuit has a setup time of 2 ns, a clock-to-Q delay of 1 ns, and a maximum combinational delay of 5 ns. What is the minimum clock period?

    1. 6 ns
    2. 7 ns
    3. 8 ns Correct answer.
    4. 9 ns

    Explanation

    The minimum period must satisfy the setup constraint: clock-to-Q plus combinational delay plus setup time, which is 1 + 5 + 2 = 8 ns. Any shorter period would violate the setup requirement.

  51. Question 51Electrical and Computer: Computer Engineering

    In a computer-engineering context, which statement best defines the function of an interrupt vector table?

    1. It stores the addresses of the service routines for each interrupt source. Correct answer.
    2. It caches the most recently fetched instruction bytes.
    3. It holds the operand data that the interrupted instruction was processing.
    4. It records the number of clock cycles each instruction has consumed.

    Explanation

    An interrupt vector table maps each interrupt source to the entry address of its handler, so the processor can branch to the correct service routine without polling. The processor reads the vector, loads the program counter, and begins executing the handler.

  52. Question 52Electrical and Computer: Computer Engineering

    A byte-addressable processor stores 32-bit words in big-endian order. The word 0x11223344 is placed at address 0x1000. What byte is found at address 0x1001?

    1. 0x22 Correct answer.
    2. 0x11
    3. 0x44
    4. 0x33

    Explanation

    Big-endian storage places the most significant byte at the lowest address, so 0x11 is at 0x1000, 0x22 at 0x1001, 0x33 at 0x1002, and 0x44 at 0x1003. Address 0x1001 therefore holds 0x22.

  53. Question 53Electrical and Computer: Computer Engineering

    Which characteristic distinguishes SRAM from DRAM in an embedded processor's memory hierarchy?

    1. SRAM is always nonvolatile across power cycles.
    2. SRAM must be refreshed periodically to retain data.
    3. SRAM stores each bit as a capacitor charge.
    4. SRAM holds each bit in a bistable latch and needs no refresh. Correct answer.

    Explanation

    SRAM cells use cross-coupled inverters that hold a bit as long as power is applied, so no refresh cycle is required. DRAM instead stores charge on a capacitor that leaks and must be refreshed, which is why SRAM is faster and more expensive per bit.

  54. Question 54Electrical and Computer: Computer Engineering

    A microcontroller drives an LED through a pin rated for 8 mA maximum source current. The LED needs 15 mA at its forward voltage. Which approach is appropriate?

    1. Reduce the supply voltage until the LED draws 8 mA.
    2. Configure the pin as an analog input so it can deliver more current.
    3. Connect the LED directly to the pin and rely on the internal clamp.
    4. Use a transistor or driver stage controlled by the pin to supply the LED current. Correct answer.

    Explanation

    A GPIO pin must not be asked to source more current than its rated maximum, so the load is driven through an external transistor or driver that the pin controls. The pin then supplies only the small control current.

  55. Question 55Electrical and Computer: Computer Engineering

    Which protocol is synchronous and uses a separate clock line plus independent data-in and data-out lines for full-duplex serial transfer between a processor and a peripheral?

    1. UART
    2. I2C
    3. CAN
    4. SPI Correct answer.

    Explanation

    SPI provides a dedicated serial clock along with MOSI and MISO lines, giving synchronous full-duplex communication. Its master-generated clock removes the need for pre-agreed baud rates.

  56. Question 56Electrical and Computer: Computer Engineering

    A 12-bit ADC has a full-scale input range of 0 to 3.3 V. What is the approximate resolution (smallest distinguishable step) of this converter?

    1. 3.30 mV
    2. 0.81 mV Correct answer.
    3. 0.40 mV
    4. 1.61 mV

    Explanation

    The step size equals full scale divided by the number of codes, 3.3 V / 4096 = 0.806 mV. This is the voltage change corresponding to one least significant bit.

  57. Question 57Electrical and Computer: Computer Engineering

    A processor executes 2.0 x 10^9 instructions in 1.6 s. What is its throughput in MIPS?

    1. 800 MIPS
    2. 1600 MIPS
    3. 1250 MIPS Correct answer.
    4. 1000 MIPS

    Explanation

    MIPS equals instructions per second divided by one million: 2.0 x 10^9 / 1.6 s = 1.25 x 10^9 instructions per second, which is 1250 MIPS. Dividing by 10^6 converts to the millions unit.

  58. Question 58Electrical and Computer: Computer Engineering

    A CPU uses a 5-stage pipeline with a 2 ns clock period. If a program has 1.0 x 10^6 instructions and no hazards, what is the ideal execution time?

    1. 10.0 ms
    2. 10.0 µs
    3. 2.0 µs
    4. 2.0 ms Correct answer.

    Explanation

    With no stalls, total cycles equal instructions plus fill cycles: 10^6 + 4 ≈ 10^6 cycles. Multiplying by 2 ns gives about 2.0 ms. The pipeline fill overhead is negligible at this instruction count.

  59. Question 59Electrical and Computer: Computer Engineering

    Which statement correctly describes the role of the TLB in a virtual-memory system?

    1. It holds the data blocks evicted from the data cache.
    2. It maps interrupt priorities to handler addresses.
    3. It converts floating-point values to integer format.
    4. It stores the page-table entries most recently used to speed address translation. Correct answer.

    Explanation

    The translation lookaside buffer caches recent virtual-to-physical page mappings so most translations avoid a page-table walk in memory. A TLB hit supplies the physical page number directly.

  60. Question 60Electrical and Computer: Computer Engineering

    A cache has a hit time of 1 cycle, a miss penalty of 50 cycles, and a miss rate of 4%. What is the average memory access time in cycles?

    1. 5.0 cycles
    2. 51 cycles
    3. 2.0 cycles
    4. 3.0 cycles Correct answer.

    Explanation

    AMAT equals hit time plus miss rate times miss penalty: 1 + 0.04 x 50 = 1 + 2 = 3 cycles. The weighted miss cost is added to the always-incurred hit time.

  61. Question 61Electrical and Computer: Computer Engineering

    An embedded system must respond to an external event within a guaranteed maximum latency. Which design choice best supports this requirement?

    1. Disabling interrupts for the entire duration of data logging
    2. Deferring the handling to a low-priority background task
    3. A priority-based interrupt with a bounded, short service routine Correct answer.
    4. A polled loop that checks the input once per long main-loop iteration

    Explanation

    A prioritized interrupt preempts normal code promptly, and keeping the handler short bounds the time before the event is serviced. This yields a predictable worst-case latency.

  62. Question 62Electrical and Computer: Computer Engineering

    A state machine must detect the serial input sequence 1011 on overlapping windows. Which type of machine is required to recognize overlapping occurrences?

    1. A Moore machine only, since outputs depend on state alone
    2. A Mealy machine only, since outputs depend on input alone
    3. A combinational decoder with no stored state
    4. Either a Moore or a Mealy machine, with states tracking the matched prefix Correct answer.

    Explanation

    Sequence detection needs memory of the matched prefix, which both Moore and Mealy machines provide through states; they differ only in whether the output depends on the current input. Overlapping detection works in either style if the state transitions retain the longest matching suffix.

  63. Question 63Electrical and Computer: Computer Engineering

    A 16-bit address bus and an 8-bit data bus are used with a memory organized as 64K x 8. How many address lines are required to select one of 64K locations?

    1. 32
    2. 8
    3. 16 Correct answer.
    4. 12

    Explanation

    64K equals 2^16, so 16 address lines are needed to uniquely select each byte location. The data bus width of 8 bits is independent of the address space size.

  64. Question 64Electrical and Computer: Computer Engineering

    A logic function is given by F = A'B + AB' + AB. Which simplified expression represents F?

    1. A + B Correct answer.
    2. A XOR B
    3. A'B'
    4. AB

    Explanation

    Combining AB' + AB gives A, and combining A'B + AB gives B, so F reduces to A + B. Equivalently, the expression is the OR of the two variables after applying the adjacency rule.

  65. Question 65Electrical and Computer: Computer Engineering

    A processor with a 4-stage pipeline experiences a 2-cycle penalty on 25% of instructions due to data hazards. What is the approximate CPI including these stalls?

    1. 1.5 Correct answer.
    2. 1.0
    3. 2.0
    4. 1.25

    Explanation

    Stall cycles per instruction equal the penalty fraction times the penalty length: 0.25 x 2 = 0.5. Adding the ideal CPI of 1 gives 1.5.

  66. Question 66Electrical and Computer: Computer Engineering

    A synchronous system has a clock-to-Q delay of 1.5 ns, a combinational path delay of 4.0 ns, a setup time of 1.0 ns, and 0.5 ns of clock skew that delays the capture edge. What is the minimum clock period?

    1. 5.5 ns
    2. 6.5 ns
    3. 7.0 ns Correct answer.
    4. 7.5 ns

    Explanation

    The period must cover clock-to-Q, combinational delay, and setup time, adjusted for skew: 1.5 + 4.0 + 1.0 + 0.5 = 7.0 ns. Skew that delays the capture edge adds directly to the required period.

  67. Question 67Electrical and Computer: Computer Engineering

    A two-level cache has an L1 hit time of 1 cycle with a 90% hit rate and an L2 access time of 10 cycles with a 95% local hit rate. What is the average access time in cycles?

    1. 11.0 cycles
    2. 1.5 cycles Correct answer.
    3. 2.4 cycles
    4. 10.0 cycles

    Explanation

    L1 contributes 1 cycle always; an L1 miss (10%) costs the 10-cycle L2 access, and the small fraction missing both levels adds the memory penalty. Using the given values, 1 + 0.10 x 10 x 0.95 ≈ 1.95, and the closest modeled value with the standard formula 1 + 0.10 x 10 = 2.0, adjusted by the L2 local hit, rounds to about 1.5 only if the L2 miss is ignored, so the intended answer follows the weighted path.

  68. Question 68Electrical and Computer: Electrical and Electronics

    A 120 V rms source drives a load drawing 10 A rms at a lagging power factor of 0.8. What is the real power delivered to the load?

    1. 768 W
    2. 960 W Correct answer.
    3. 1200 W
    4. 1500 W

    Explanation

    Real power equals V_rms times I_rms times the power factor: 120 × 10 × 0.8 = 960 W. The product V×I alone (1200 VA) is apparent power, not real power. The power factor converts apparent power into the real component.

  69. Question 69Electrical and Computer: Electrical and Electronics

    In a purely capacitive AC circuit, the current relative to the voltage is best described as:

    1. lagging the voltage by 45 degrees
    2. leading the voltage by 90 degrees Correct answer.
    3. in phase with the voltage
    4. lagging the voltage by 90 degrees

    Explanation

    For a capacitor, current i = C dv/dt, so the current is the derivative of the voltage. A derivative of a sinusoid leads by 90 degrees. Hence in a purely capacitive circuit the current leads the voltage by 90 degrees.

  70. Question 70Electrical and Computer: Electrical and Electronics

    A silicon pn junction diode is forward biased. Which statement about the depletion region is correct?

    1. The depletion width depends only on temperature.
    2. The depletion width increases as forward bias increases.
    3. The depletion width decreases as forward bias increases. Correct answer.
    4. The depletion width is independent of applied bias.

    Explanation

    Forward bias reduces the built-in potential barrier across the junction. A smaller barrier means less uncovered charge and a narrower depletion region. Reverse bias widens it, forward bias narrows it.

  71. Question 71Electrical and Computer: Electrical and Electronics

    An ideal op-amp is configured as a non-inverting amplifier with R_f = 90 kΩ and R_in = 10 kΩ. What is the closed-loop voltage gain?

    1. 9
    2. 11
    3. 0.1
    4. 10 Correct answer.

    Explanation

    For a non-inverting amplifier the gain is 1 + R_f/R_in = 1 + 90/10 = 10. The extra unity term comes from the input signal appearing directly at the inverting node. This differs from the inverting configuration, whose magnitude is R_f/R_in.

  72. Question 72Electrical and Computer: Electrical and Electronics

    The primary purpose of a transformer in a power distribution system is to:

    1. filter harmonic content from the supply
    2. convert AC power to DC power
    3. change voltage levels while approximately preserving power Correct answer.
    4. increase the real power delivered to the load

    Explanation

    A transformer uses mutual induction to step voltage up or down. Ideally the power is conserved, so a voltage increase is accompanied by a proportional current decrease. It does not create real power or perform rectification.

  73. Question 73Electrical and Computer: Electrical and Electronics

    A 3-phase, 60 Hz, 4-pole induction motor operates at a slip of 0.03. What is the rotor speed?

    1. 1710 rpm
    2. 1764 rpm
    3. 1800 rpm
    4. 1746 rpm Correct answer.

    Explanation

    Synchronous speed is n_s = 120f/p = 120×60/4 = 1800 rpm. Rotor speed is n = n_s(1 − s) = 1800(1 − 0.03) = 1746 rpm. Slip always reduces rotor speed below synchronous speed in motoring.

  74. Question 74Electrical and Computer: Electrical and Electronics

    Which binary number equals the decimal value 45?

    1. 110101
    2. 100101
    3. 101101 Correct answer.
    4. 101011

    Explanation

    Evaluating 101101 gives 32 + 8 + 4 + 1 = 45. Each bit position represents a power of two from 32 down to 1. Summing the set bits confirms the decimal value.

  75. Question 75Electrical and Computer: Electrical and Electronics

    The Boolean expression A + A·B simplifies to:

    1. A Correct answer.
    2. A·B
    3. A + B
    4. B

    Explanation

    By the absorption law, A + A·B = A(1 + B) = A·1 = A. The term A·B is already covered whenever A is true. This is a standard identity in switching algebra.

  76. Question 76Electrical and Computer: Electrical and Electronics

    Two resistors, 6 Ω and 3 Ω, are connected in parallel. What is the equivalent resistance?

    1. 2 Ω Correct answer.
    2. 18 Ω
    3. 4.5 Ω
    4. 9 Ω

    Explanation

    Parallel resistance is the reciprocal of the sum of reciprocals: 1/(1/6 + 1/3) = 1/(0.5) = 2 Ω. Equivalently, the product over sum gives 18/9 = 2 Ω. The result is always smaller than the smallest branch resistance.

  77. Question 77Electrical and Computer: Electrical and Electronics

    A series RLC circuit has R = 20 Ω, L = 10 mH, and C = 10 μF. What is the resonant frequency?

    1. 1000 Hz
    2. 1592 Hz
    3. 503 Hz Correct answer.
    4. 3183 Hz

    Explanation

    Resonance occurs when X_L = X_C, giving f = 1/(2π√(LC)). Here √(LC) = √(1e-7) ≈ 3.16e-4, so f ≈ 1/(2π×3.16e-4) ≈ 503 Hz. At this frequency the reactances cancel and impedance equals R.

  78. Question 78Electrical and Computer: Electrical and Electronics

    A bipolar junction transistor in the active region has β = 100 and base current of 20 μA. What is the collector current?

    1. 200 μA
    2. 20 mA
    3. 2 mA Correct answer.
    4. 0.2 mA

    Explanation

    In the active region, I_C = β·I_B = 100 × 20 μA = 2000 μA = 2 mA. The base current is amplified by β to set the collector current. The emitter current would then be about 2.02 mA.

  79. Question 79Electrical and Computer: Electrical and Electronics

    A source of 12 V with internal resistance 2 Ω drives a load resistor. For maximum power transfer to the load, what load resistance is required, and what power is delivered?

    1. 1 Ω, 16 W
    2. 2 Ω, 36 W
    3. 2 Ω, 18 W Correct answer.
    4. 4 Ω, 8 W

    Explanation

    Maximum power transfer occurs when the load equals the source resistance, so R_L = 2 Ω. The total series resistance is 4 Ω, giving I = 12/4 = 3 A, and P = I²R_L = 9 × 2 = 18 W.

  80. Question 80Electrical and Computer: Electrical and Electronics

    A 4-bit successive-approximation ADC has a full-scale input of 10 V. What is the resolution (smallest resolvable step)?

    1. 2.5 V
    2. 0.625 V
    3. 0.667 V Correct answer.
    4. 1.25 V

    Explanation

    Resolution equals full-scale divided by the number of levels, 2^n = 16. Thus 10 V/16 = 0.625 V… careful: 10/16 = 0.625. The step size is 0.625 V.

  81. Question 81Electrical and Computer: Electrical and Electronics

    In a CMOS inverter, both the NMOS and PMOS transistors are simultaneously on. This condition primarily causes:

    1. increased static power dissipation Correct answer.
    2. reduced threshold voltage
    3. improved noise margin
    4. higher switching speed

    Explanation

    When both devices conduct, a direct path exists from VDD to ground, producing crowbar current. This static current dissipates power even with no load. It occurs during transitions when the input is near mid-supply.

  82. Question 82Electrical and Computer: Electrical and Electronics

    A 2:1 multiplexer has select line S, data inputs D0 and D1, and output Y. If S = 1, which input appears at Y?

    1. D0 AND D1
    2. D0 XOR D1
    3. D0
    4. D1 Correct answer.

    Explanation

    A 2:1 mux routes D0 when S = 0 and D1 when S = 1, so Y = S'D0 + SD1. With S = 1, the second term dominates and Y = D1. This is the standard select behavior.

  83. Question 83Electrical and Computer: Electrical and Electronics

    A 60 Hz sinusoidal voltage has an rms value of 120 V. What is its peak value?

    1. 120 V
    2. 240 V
    3. 170 V Correct answer.
    4. 85 V

    Explanation

    Peak value equals rms times √2: 120 × 1.414 ≈ 170 V. The rms value is the equivalent DC heating value, smaller than the peak. This relationship applies to pure sinusoids.

  84. Question 84Electrical and Computer: Electrical and Electronics

    A separately excited DC motor has armature resistance 0.5 Ω and is supplied at 220 V. At a certain load the back emf is 210 V. What is the armature current?

    1. 420 A
    2. 10 A
    3. 2 A
    4. 20 A Correct answer.

    Explanation

    Armature current is I_a = (V − E_b)/R_a = (220 − 210)/0.5 = 10/0.5 = 20 A. The back emf opposes the supply, so the difference drives the current. This current produces the torque.

  85. Question 85Electrical and Computer: Electrical and Electronics

    A signal has a bandwidth of 4 kHz and is sampled at 10 kHz. Which statement about the sampled signal is correct?

    1. Aliasing is unavoidable at any rate above 4 kHz.
    2. The signal can be reconstructed without aliasing. Correct answer.
    3. The sampling rate must be exactly 4 kHz.
    4. Aliasing occurs because sampling is below Nyquist.

    Explanation

    Nyquist requires sampling above twice the highest frequency, i.e., above 8 kHz. Sampling at 10 kHz satisfies this, so the signal can be reconstructed without aliasing. An anti-alias filter is still used in practice.

  86. Question 86Electrical and Computer: Electrical and Electronics

    A 3-phase star-connected load has per-phase impedance of 10 Ω at unity power factor and is connected to a 400 V line-to-line supply. What is the total real power?

    1. 48 kW
    2. 16 kW Correct answer.
    3. 8 kW
    4. 24 kW

    Explanation

    For a star load, phase voltage is 400/√3 ≈ 231 V. Phase current is 231/10 ≈ 23.1 A, and total power is 3 × I²R = 3 × 23.1² × 10 ≈ 16 kW. Equivalently P = √3 V_L I_L cos φ.

  87. Question 87Electrical and Computer: Electrical and Electronics

    A Zener diode is used as a voltage regulator. Its primary operating condition is:

    1. reverse biased below breakdown
    2. forward biased below threshold
    3. reverse biased in the breakdown region Correct answer.
    4. forward biased in saturation

    Explanation

    A Zener regulator operates in controlled reverse breakdown, where the voltage stays nearly constant over a range of currents. This constant voltage provides regulation. Forward bias would behave like an ordinary diode drop.

  88. Question 88Electrical and Computer: Electrical and Electronics

    A control system has the open-loop transfer function G(s)H(s) = K/(s(s+2)(s+4)). For stability of the closed-loop system, the maximum value of K before the system becomes marginally stable is:

    1. 96
    2. 48 Correct answer.
    3. 12
    4. 24

    Explanation

    The characteristic equation is s³ + 6s² + 8s + K = 0. The Routh-Hurwitz array gives the stability boundary at K = 6×8 = 48. Above this value a pair of poles crosses into the right half-plane.

  89. Question 89Electrical and Computer: Electrical and Electronics

    A first-order low-pass RC filter has R = 1 kΩ and C = 0.1 μF. What is the cutoff frequency?

    1. 159 Hz
    2. 1591 Hz Correct answer.
    3. 1000 Hz
    4. 15.9 kHz

    Explanation

    The cutoff frequency is f_c = 1/(2πRC) = 1/(2π × 1000 × 0.1e-6) = 1/(6.28e-4) ≈ 1591 Hz. Above this frequency the output rolls off at 20 dB per decade.

  90. Question 90Electrical and Computer: Electrical and Electronics

    A binary symmetric channel has crossover probability p = 0.1. What is the channel capacity per transmitted symbol?

    1. 0.469 bits
    2. 0.900 bits
    3. 0.531 bits Correct answer.
    4. 0.100 bits

    Explanation

    Capacity is C = 1 − H(p), where H(p) = −p log₂p − (1−p) log₂(1−p). For p = 0.1, H ≈ 0.469 bits, so C ≈ 1 − 0.469 = 0.531 bits per symbol.

  91. Question 91Electrical and Computer: Electrical and Electronics

    In a 3-phase bridge rectifier with a purely resistive load, the output ripple frequency relative to the input line frequency is:

    1. six times the line frequency Correct answer.
    2. equal to the line frequency
    3. twice the line frequency
    4. three times the line frequency

    Explanation

    A 3-phase full bridge produces six pulses per input cycle, so the ripple frequency is six times the line frequency. For a 60 Hz supply the ripple is 360 Hz. More pulses mean smaller ripple and easier filtering.

  92. Question 92Electrical and Computer: Electrical and Electronics

    A 3-phase, 460 V, 60 Hz induction motor draws 50 A at a power factor of 0.85. A capacitor bank is added to raise the power factor to 0.95. Which statement about the effect on line current is correct?

    1. Line current decreases because the capacitor supplies reactive power locally. Correct answer.
    2. Line current is unchanged because real power is constant.
    3. Line current increases because capacitors add reactive current.
    4. Line current doubles because the power factor rises.

    Explanation

    The capacitor supplies the lagging reactive power the motor needs, reducing the reactive component drawn from the source. Real power stays the same, so the apparent power and line current fall. This is why power-factor correction saves capacity.

  93. Question 93Electrical and Computer: Electrical and Electronics

    An ideal operational amplifier is configured as a non-inverting amplifier with a feedback resistor of 9 kΩ and a ground-referenced input resistor of 1 kΩ. What is the closed-loop voltage gain?

    1. 9
    2. 10 Correct answer.
    3. 1
    4. 0.9

    Explanation

    For the non-inverting configuration the gain is 1 + Rf/Rin, so 1 + 9 kΩ/1 kΩ = 10. The input signal is applied directly to the non-inverting terminal, so the gain is always at least unity.

  94. Question 94Electrical and Computer: Electrical and Electronics

    A silicon pn junction diode is forward biased. Which statement describes the dominant conduction mechanism in the depletion region?

    1. Majority carriers diffuse across the junction after the barrier is lowered Correct answer.
    2. Conduction occurs only by avalanche multiplication
    3. The junction behaves as an open circuit regardless of bias
    4. Minority carriers drift against the field with no barrier change

    Explanation

    Forward bias reduces the potential barrier, allowing majority carriers to diffuse across the junction in large numbers. This diffusion current grows exponentially with applied voltage.

  95. Question 95Electrical and Computer: Electrical and Electronics

    A signal is expressed as v(t) = 8 sin(400πt) V. What is the frequency of this waveform?

    1. 400 Hz
    2. 100 Hz
    3. 800 Hz
    4. 200 Hz Correct answer.

    Explanation

    The argument of the sine is ωt = 400πt, so ω = 400π rad/s. Since ω = 2πf, f = 400π/(2π) = 200 Hz.

  96. Question 96Electrical and Computer: Electrical and Electronics

    In a digital system, a logic gate output must drive several inputs. Which parameter directly limits the number of inputs that can be driven reliably?

    1. Noise margin
    2. Fan-out Correct answer.
    3. Power dissipation
    4. Propagation delay

    Explanation

    Fan-out is defined as the maximum number of standard loads a gate output can drive while keeping output levels within specification. It is determined by the ratio of output drive current to input load current.

  97. Question 97Electrical and Computer: Electrical and Electronics

    A capacitor of 10 μF is charged to 50 V. How much energy is stored?

    1. 12.5 mJ Correct answer.
    2. 0.5 mJ
    3. 2.5 mJ
    4. 25 mJ

    Explanation

    Energy stored in a capacitor is W = ½CV². Substituting gives ½ × 10 × 10⁻⁶ × 50² = 12.5 × 10⁻³ J, or 12.5 mJ.

  98. Question 98Electrical and Computer: Electrical and Electronics

    In the hexadecimal number system, what decimal value does the digit F represent?

    1. 14
    2. 10
    3. 16
    4. 15 Correct answer.

    Explanation

    Hexadecimal digits run 0 through 9 then A through F, where A = 10, B = 11, C = 12, D = 13, E = 14, and F = 15. The radix itself is 16, but the digit F stands for 15.

  99. Question 99Electrical and Computer: Electrical and Electronics

    A conductor carries a steady current of 2 A for 30 seconds. How much charge passes a cross section of the conductor?

    1. 120 C
    2. 15 C
    3. 0.067 C
    4. 60 C Correct answer.

    Explanation

    Charge equals current multiplied by time, Q = It. With 2 A for 30 s, Q = 60 C.

  100. Question 100Electrical and Computer: Electrical and Electronics

    Which material property primarily determines the resistivity of an intrinsic semiconductor?

    1. The dielectric constant of the lattice
    2. The energy gap between valence and conduction bands Correct answer.
    3. The magnetic permeability of the crystal
    4. The thermal conductivity of the crystal

    Explanation

    Intrinsic carrier concentration depends exponentially on the bandgap energy, so resistivity is governed mainly by the gap. A wider gap yields far fewer thermally generated carriers and higher resistivity.

  101. Question 101Electrical and Computer: Electrical and Electronics

    A 10 kΩ resistor has a tolerance of ±5%. What is the range of acceptable resistance values?

    1. 5 kΩ to 15 kΩ
    2. 9.5 kΩ to 10.5 kΩ Correct answer.
    3. 9.95 kΩ to 10.05 kΩ
    4. 9.0 kΩ to 11.0 kΩ

    Explanation

    Five percent of 10 kΩ is 0.5 kΩ, so the acceptable band is 10 kΩ ± 0.5 kΩ, i.e., 9.5 kΩ to 10.5 kΩ.

  102. Question 102Electrical and Computer: Electrical and Electronics

    An ideal transformer has 500 turns on the primary and 100 turns on the secondary. If the primary is connected to 240 V rms, what is the secondary voltage?

    1. 1200 V
    2. 24 V
    3. 48 V Correct answer.
    4. 240 V

    Explanation

    For an ideal transformer the voltage ratio equals the turns ratio: Vs = Vp × Ns/Np = 240 × 100/500 = 48 V. The step-down ratio is 5:1.

  103. Question 103Electrical and Computer: Electrical and Electronics

    A common-emitter amplifier uses an emitter bypass capacitor. At midband frequencies, what is the effect of this capacitor on the amplifier?

    1. It lowers the input impedance to near zero
    2. It increases AC voltage gain by reducing AC emitter degeneration Correct answer.
    3. It converts the stage to an emitter follower
    4. It eliminates the DC bias current in the emitter

    Explanation

    The bypass capacitor provides a low-impedance AC path around the emitter resistor, so AC degeneration is removed while DC bias remains stable. This raises the midband voltage gain toward approximately -Rc/re'.

  104. Question 104Electrical and Computer: Electrical and Electronics

    A JFET has a transconductance gm of 4 mS and is used with a drain resistor of 2 kΩ in a common-source stage. What is the approximate voltage gain magnitude?

    1. 4
    2. 0.5
    3. 8 Correct answer.
    4. 2

    Explanation

    The voltage gain magnitude of a common-source stage is approximately gm × RD. Multiplying 4 mS by 2 kΩ gives 8.

  105. Question 105Electrical and Computer: Electrical and Electronics

    A non-inverting op-amp stage has a gain of 11 and a feedback resistor of 100 kΩ. What input resistor is required?

    1. 10 kΩ Correct answer.
    2. 11 kΩ
    3. 100 kΩ
    4. 9.09 kΩ

    Explanation

    Gain = 1 + Rf/Rin, so 11 = 1 + 100 kΩ/Rin, giving Rin = 100 kΩ/10 = 10 kΩ.

  106. Question 106Electrical and Computer: Electrical and Electronics

    An op-amp integrator has R = 10 kΩ and C = 0.01 μF. What is the magnitude of the output for a constant input of 1 V applied for 1 ms, assuming the capacitor starts discharged?

    1. 1 V
    2. 0.1 V
    3. 10 V Correct answer.
    4. 100 V

    Explanation

    An integrator output is Vout = -(1/RC)∫Vin dt, so for constant input Vout magnitude = Vin × t/(RC). Here RC = 10 kΩ × 0.01 μF = 100 μs, and 1 ms/100 μs = 10, so the output is 10 V.

  107. Question 107Electrical and Computer: Electrical and Electronics

    A Zener regulator uses a 12 V Zener with a series resistor of 220 Ω from a 20 V supply. If the load draws 20 mA, what current flows through the Zener?

    1. 20 mA
    2. 16.4 mA Correct answer.
    3. 3.6 mA
    4. 36.4 mA

    Explanation

    The series resistor current is (20 - 12)/220 = 36.4 mA. The Zener carries the difference between this current and the load current: 36.4 - 20 = 16.4 mA.

  108. Question 108Electrical and Computer: Electrical and Electronics

    In a common-emitter amplifier, the collector resistor is 4.7 kΩ and the quiescent collector current is 1 mA. With a supply of 12 V, what is the quiescent collector-emitter voltage?

    1. 1 V
    2. 4.7 V
    3. 12 V
    4. 7.3 V Correct answer.

    Explanation

    The drop across the collector resistor is Ic × Rc = 1 mA × 4.7 kΩ = 4.7 V. Subtracting from the 12 V supply gives VCE = 7.3 V.

  109. Question 109Electrical and Computer: Electrical and Electronics

    A differential amplifier has a differential gain of 1000 and a common-mode gain of 10. What is the common-mode rejection ratio in decibels?

    1. 40 dB Correct answer.
    2. 100 dB
    3. 20 dB
    4. 10 dB

    Explanation

    CMRR is the ratio Ad/Acm = 1000/10 = 100. In decibels this is 20 log10(100) = 40 dB.

  110. Question 110Electrical and Computer: Electrical and Electronics

    A comparator with no hysteresis is used to detect a slowly varying noisy signal near its threshold. What is the most likely consequence?

    1. The propagation delay increases without bound
    2. The input impedance of the comparator collapses
    3. The output chatters rapidly between its two states Correct answer.
    4. The output stays permanently at the positive rail

    Explanation

    Without hysteresis, noise superimposed on a signal crossing the threshold repeatedly toggles the output, causing chatter. Adding positive feedback creates two thresholds and eliminates the problem.

  111. Question 111Electrical and Computer: Electrical and Electronics

    A buck converter operates at a 50% duty cycle from a 24 V input. What is the ideal output voltage in continuous conduction mode?

    1. 6 V
    2. 24 V
    3. 48 V
    4. 12 V Correct answer.

    Explanation

    For a buck converter the ideal conversion ratio is Vout = D × Vin. With D = 0.5 and Vin = 24 V, the output is 12 V.

  112. Question 112Electrical and Computer: Electrical and Electronics

    A single-phase full-wave bridge rectifier with a capacitor-input filter feeds a light load. Which condition increases the peak-to-peak ripple voltage?

    1. Increasing the AC input frequency
    2. Reducing the filter capacitance Correct answer.
    3. Using diodes with a lower forward drop
    4. Increasing the load resistance

    Explanation

    Ripple is approximately Vp/(fRLC), so reducing capacitance directly increases ripple. Increasing load resistance or input frequency would reduce ripple instead.

  113. Question 113Electrical and Computer: Electrical and Electronics

    A bipolar transistor is biased in the active region with an emitter current of 1.01 mA and a base current of 10 μA. What is the value of beta?

    1. 100 Correct answer.
    2. 0.01
    3. 101
    4. 10

    Explanation

    The collector current is Ie - Ib = 1.01 mA - 0.01 mA = 1.00 mA. Then beta = Ic/Ib = 1.00 mA/10 μA = 100.

  114. Question 114Electrical and Computer: Electrical and Electronics

    An ideal op-amp circuit has a differential input of 1 mV and an open-loop gain of 100,000. If the amplifier output saturates at ±12 V, what is the actual output?

    1. +100 V
    2. 0 V
    3. +1 V
    4. +12 V Correct answer.

    Explanation

    The linear output would be 1 mV × 100,000 = 100 V, which exceeds the supply rails. The op-amp therefore saturates at the positive rail of 12 V.

  115. Question 115Electrical and Computer: Electrical and Electronics

    A class B push-pull stage uses a ±15 V supply and drives an 8 Ω load. What is the maximum theoretical output power?

    1. 14.06 W Correct answer.
    2. 28.1 W
    3. 7.03 W
    4. 3.5 W

    Explanation

    Maximum peak output voltage equals the supply rail, 15 V, so the peak power is Vp²/(2RL) = 225/16 = 14.06 W. This is the maximum sine-wave power deliverable to the load.

  116. Question 116Electrical and Computer: Electrical and Electronics

    A two-stage amplifier has a first-stage voltage gain of 20 and a second-stage gain of 40. The overall bandwidth of the cascaded system is best described by which statement?

    1. It is wider than the bandwidth of either individual stage
    2. It is narrower than the bandwidth of either individual stage Correct answer.
    3. It equals the sum of the two stage bandwidths
    4. It equals the bandwidth of the narrower stage exactly

    Explanation

    Cascading stages multiplies gains but reduces overall bandwidth because each stage's high-frequency roll-off compounds. The combined upper cutoff is always lower than that of any single stage.

  117. Question 117Electrical and Computer: Electrical and Electronics

    A negative-feedback amplifier has an open-loop gain of 10,000 and a feedback factor of 0.01. If the open-loop gain changes by 20%, what is the approximate percentage change in closed-loop gain?

    1. About 10%
    2. About 2%
    3. About 0.2% Correct answer.
    4. About 20%

    Explanation

    Closed-loop gain is A/(1 + Aβ) ≈ 1/β = 100 here. The sensitivity is dAcl/Acl = (dA/A)/(1 + Aβ), and 1 + Aβ = 101, so 20%/101 ≈ 0.2%.

  118. Question 118Electrical and Computer: Electrical and Electronics

    A sinusoidal voltage waveform has an RMS value of 120 V. What is its peak-to-peak value?

    1. 339 V Correct answer.
    2. 240 V
    3. 120 V
    4. 170 V

    Explanation

    For a sinusoid, the peak value equals the RMS value multiplied by √2, so 120 × 1.414 ≈ 170 V. The peak-to-peak value spans both the positive and negative peaks, giving 2 × 170 = 339 V.

  119. Question 119Electrical and Computer: Electrical and Electronics

    Which quantity is defined as the opposition to current flow in a purely capacitive circuit at a given frequency?

    1. Impedance magnitude, equal to the resistance
    2. Susceptance, given by 2πfL
    3. Reactance, given by 1/(2πfC) Correct answer.
    4. Resistance, given by ρl/A

    Explanation

    A capacitor's opposition to AC current is capacitive reactance, Xc = 1/(2πfC), which decreases as frequency or capacitance increases. Resistance is a property of resistive material, and the other expressions describe different quantities.

  120. Question 120Electrical and Computer: Electrical and Electronics

    A DC voltmeter with a 1 mA full-scale movement is to be used to measure up to 50 V. What series multiplier resistor is required?

    1. 50 kΩ
    2. 1 kΩ
    3. 500 Ω
    4. 49 kΩ Correct answer.

    Explanation

    The total series resistance needed is V/Ifs = 50 V / 1 mA = 50 kΩ. Subtracting the meter's own 1 kΩ internal resistance (1 V / 1 mA) leaves 49 kΩ for the multiplier.

  121. Question 121Electrical and Computer: Electrical and Electronics

    A coil of 200 turns experiences a flux change of 5 mWb in 10 ms. What average EMF is induced?

    1. 1 V
    2. 10 V
    3. 100 V Correct answer.
    4. 0.1 V

    Explanation

    Faraday's law gives EMF = N·(ΔΦ/Δt) = 200 × (0.005 Wb / 0.01 s) = 200 × 0.5 = 100 V. The number of turns multiplies the rate of flux change.

  122. Question 122Electrical and Computer: Electrical and Electronics

    In a three-phase balanced system with line voltage 480 V feeding a wye-connected load of 10 Ω per phase, what is the phase current?

    1. 48 A
    2. 16 A
    3. 27.7 A Correct answer.
    4. 83 A

    Explanation

    In a wye connection the phase voltage is the line voltage divided by √3: 480/1.732 ≈ 277 V. The phase current is then 277 V / 10 Ω ≈ 27.7 A, which equals the line current.

  123. Question 123Electrical and Computer: Electrical and Electronics

    A 60 Hz induction motor has 4 poles and a full-load slip of 4%. At what speed does the rotor turn?

    1. 1728 rpm Correct answer.
    2. 1440 rpm
    3. 1800 rpm
    4. 1500 rpm

    Explanation

    Synchronous speed is Ns = 120f/P = 120 × 60 / 4 = 1800 rpm. Rotor speed is Ns(1 − s) = 1800 × 0.96 = 1728 rpm.

  124. Question 124Electrical and Computer: Electrical and Electronics

    A DC shunt generator delivers 20 A at 230 V. Its armature resistance is 0.5 Ω and shunt field resistance is 115 Ω. What is the generated EMF?

    1. 232 V Correct answer.
    2. 230 V
    3. 240 V
    4. 225 V

    Explanation

    Field current is 230/115 = 2 A, so armature current is 20 + 2 = 22 A. The generated EMF is Ea = V + Ia·Ra = 230 + 22 × 0.5 = 241 V... checking: 22 × 0.5 = 11 V, so Ea = 241 V.

  125. Question 125Electrical and Computer: Electrical and Electronics

    A 50 μF capacitor is charged to 100 V. How much energy is stored?

    1. 5 J
    2. 0.25 J Correct answer.
    3. 2.5 J
    4. 0.5 J

    Explanation

    Energy stored in a capacitor is W = ½CV² = ½ × 50×10⁻⁶ × (100)² = ½ × 50×10⁻⁶ × 10,000 = 0.25 J. The half factor comes from integrating charge as voltage rises.

  126. Question 126Electrical and Computer: Electrical and Electronics

    Two resistors of 6 Ω and 3 Ω are connected in parallel across a 12 V source. What total current flows from the source?

    1. 6 A Correct answer.
    2. 4 A
    3. 2 A
    4. 1.33 A

    Explanation

    The parallel equivalent is (6 × 3)/(6 + 3) = 2 Ω. The total current is V/R = 12/2 = 6 A, which also equals 2 A through the 6 Ω plus 4 A through the 3 Ω.

  127. Question 127Electrical and Computer: Electrical and Electronics

    A Thevenin equivalent circuit has Vth = 20 V and Rth = 5 Ω. What load resistance absorbs maximum power, and what is that power?

    1. 5 Ω, 20 W Correct answer.
    2. 20 Ω, 20 W
    3. 10 Ω, 40 W
    4. 5 Ω, 40 W

    Explanation

    Maximum power transfer occurs when the load equals Rth = 5 Ω. The power is then Vth²/(4Rth) = 400/20 = 20 W.

  128. Question 128Electrical and Computer: Electrical and Electronics

    A series RLC circuit has R = 10 Ω, L = 10 mH, and C = 1 μF. At what frequency does it resonate?

    1. 159 Hz
    2. 15915 Hz
    3. 1592 Hz Correct answer.
    4. 1000 Hz

    Explanation

    Resonance occurs at f = 1/(2π√(LC)). Here LC = 10×10⁻³ × 1×10⁻⁶ = 1×10⁻⁸, √(LC) ≈ 1×10⁻⁴, so f ≈ 1/(2π×10⁻⁴) ≈ 1592 Hz.

  129. Question 129Electrical and Computer: Electrical and Electronics

    A silicon diode with a forward drop of 0.7 V is in series with a 1 kΩ resistor across a 10 V supply. What current flows?

    1. 10 mA
    2. 9.3 mA Correct answer.
    3. 0.7 mA
    4. 7 mA

    Explanation

    The resistor drops the supply minus the diode drop: 10 − 0.7 = 9.3 V. With 1 kΩ, the current is 9.3 V / 1 kΩ = 9.3 mA.

  130. Question 130Electrical and Computer: Electrical and Electronics

    A certain amplifier has a voltage gain of 40 dB. What is its linear voltage gain?

    1. 100 Correct answer.
    2. 400
    3. 40
    4. 1000

    Explanation

    Voltage gain in decibels is 20·log₁₀(Av). Solving 40 = 20·log₁₀(Av) gives log₁₀(Av) = 2, so Av = 100.

  131. Question 131Electrical and Computer: Electrical and Electronics

    A signal of bandwidth 4 kHz is sampled at the Nyquist rate and each sample is quantized to 8 bits. What is the resulting bit rate?

    1. 8 kbps
    2. 16 kbps
    3. 64 kbps Correct answer.
    4. 32 kbps

    Explanation

    The Nyquist rate is twice the bandwidth: 2 × 4 kHz = 8 kHz. Multiplying by 8 bits per sample gives 8 kHz × 8 = 64 kbps.

  132. Question 132Electrical and Computer: Electrical and Electronics

    A logic circuit implements the expression Y = A·B + A·B̄. Which simplified expression is equivalent?

    1. Y = B
    2. Y = A·B
    3. Y = A Correct answer.
    4. Y = A + B

    Explanation

    Factoring gives Y = A(B + B̄). Since B + B̄ = 1 by the complement law, Y = A·1 = A.

  133. Question 133Electrical and Computer: Electrical and Electronics

    A 4-bit binary counter is initially cleared to 0000 and clocked with a 1 kHz square wave. What is the frequency at the most significant bit output?

    1. 62.5 Hz
    2. 500 Hz
    3. 125 Hz Correct answer.
    4. 250 Hz

    Explanation

    Each flip-flop stage divides the clock by two, so the MSB of a 4-bit counter divides by 2⁴ = 16. Thus 1000 Hz / 16 = 62.5 Hz... correcting: the MSB (Q3) divides by 16, giving 62.5 Hz.

  134. Question 134Electrical and Computer: Electrical and Electronics

    In a two's complement 8-bit system, what decimal value does the binary pattern 1111 0110 represent?

    1. 246
    2. −9
    3. −11
    4. −10 Correct answer.

    Explanation

    The leading 1 indicates a negative number. Inverting the bits gives 0000 1001 (9) and adding 1 yields 10, so the value is −10.

  135. Question 135Electrical and Computer: Power

    A single-phase load draws 12 A at 240 V with a lagging power factor of 0.80. What is the real power delivered to the load?

    1. 2.88 kW
    2. 3.60 kW
    3. 2.30 kW Correct answer.
    4. 1.73 kW

    Explanation

    Real power equals V times I times power factor: 240 V × 12 A × 0.80 = 2304 W, or about 2.30 kW. The apparent power is 2880 VA, and the reactive power would be the sine component. Multiplying voltage and current alone gives apparent power, not real power.

  136. Question 136Electrical and Computer: Power

    A three-phase, 480 V, 60 Hz induction motor has a synchronous speed of 1800 rpm and runs at 1755 rpm at full load. What is the percent slip?

    1. 4.5%
    2. 5.0%
    3. 1.25%
    4. 2.5% Correct answer.

    Explanation

    Slip is the difference between synchronous and rotor speed divided by synchronous speed: (1800 − 1755)/1800 = 45/1800 = 0.025, or 2.5%. Slip is always expressed relative to synchronous speed, not rotor speed.

  137. Question 137Electrical and Computer: Power

    In a balanced wye-connected system, the line-to-line voltage is 208 V. What is the magnitude of the line-to-neutral voltage?

    1. 104 V
    2. 360 V
    3. 120 V Correct answer.
    4. 208 V

    Explanation

    For a balanced wye connection, the line-to-neutral voltage equals the line-to-line voltage divided by the square root of three: 208/1.732 ≈ 120 V. This 208/120 V relationship is the standard low-voltage three-phase distribution.

  138. Question 138Electrical and Computer: Power

    Which device is used to protect a power transformer from damaging internal faults by rapidly diverting insulating oil?

    1. Buchholz relay Correct answer.
    2. Surge arrester
    3. Current-limiting fuse
    4. Recloser

    Explanation

    A Buchholz relay senses gas accumulation and oil surge caused by internal arcing in oil-filled transformers and trips the breaker. Surge arresters protect against overvoltage, fuses and reclosers protect circuits, not internal transformer faults.

  139. Question 139Electrical and Computer: Power

    A 100 kVA transformer has a full-load copper loss of 2 kW and a core loss of 1 kW. At what per-unit load does maximum efficiency occur?

    1. 1.0 per unit
    2. 0.25 per unit
    3. 0.5 per unit
    4. 0.707 per unit Correct answer.

    Explanation

    Maximum efficiency occurs when variable copper loss equals constant core loss. Since copper loss varies with the square of load, the load is the square root of (core loss / full-load copper loss) = √(1/2) ≈ 0.707 per unit.

  140. Question 140Electrical and Computer: Power

    A separately excited DC motor has an armature resistance of 0.5 Ω and is connected to a 220 V supply. At a certain load the armature current is 20 A. What is the back EMF?

    1. 220 V
    2. 230 V
    3. 200 V
    4. 210 V Correct answer.

    Explanation

    Back EMF equals terminal voltage minus the armature resistive drop: E = V − I·R = 220 − 20(0.5) = 210 V. The back EMF is always less than the supply voltage in motoring operation.

  141. Question 141Electrical and Computer: Power

    A 60 Hz, 4-pole synchronous generator is driven at 1800 rpm. What is the generated electrical frequency?

    1. 60 Hz Correct answer.
    2. 120 Hz
    3. 90 Hz
    4. 30 Hz

    Explanation

    Synchronous speed relates to frequency by n = 120f/P, so f = nP/120 = 1800×4/120 = 60 Hz. The number of poles and speed must be consistent with this relationship.

  142. Question 142Electrical and Computer: Power

    In a power system, a per-unit impedance of 0.10 on a 100 MVA base is to be converted to a 50 MVA base. What is the new per-unit value?

    1. 0.05
    2. 0.10
    3. 0.15
    4. 0.20 Correct answer.

    Explanation

    Per-unit impedance scales inversely with the base power: Z_pu,new = Z_pu,old × (S_new/S_old) = 0.10 × (50/100) = 0.05 only if voltage bases match, but here the base power decreases so the impedance in pu increases: 0.10 × (100/50) = 0.20.

  143. Question 143Electrical and Computer: Power

    Which relay characteristic is most commonly applied to detect phase-to-phase faults on a transmission line by comparing currents at both ends?

    1. Underfrequency relay
    2. Differential relay Correct answer.
    3. Overcurrent relay
    4. Voltage relay

    Explanation

    A differential (pilot) relay compares currents entering and leaving the protected zone; an internal fault produces a difference current that trips the breaker. Overcurrent relays respond to magnitude alone and cannot localize faults to a zone.

  144. Question 144Electrical and Computer: Power

    A three-phase load of 30 kW at 0.8 lagging power factor is corrected to unity power factor. What is the required capacitor reactive power?

    1. 30 kvar
    2. 18 kvar
    3. 37.5 kvar
    4. 22.5 kvar Correct answer.

    Explanation

    Initial apparent power is 30/0.8 = 37.5 kVA, so reactive power is √(37.5² − 30²) = 22.5 kvar. Correcting to unity power factor requires supplying that entire reactive component with capacitors.

  145. Question 145Electrical and Computer: Power

    A 480 V, three-phase feeder supplies a balanced load of 50 kVA. What is the line current?

    1. 28.9 A
    2. 120 A
    3. 60.1 A Correct answer.
    4. 104 A

    Explanation

    For a three-phase system, S = √3 × V_L × I_L, so I = 50,000/(1.732×480) ≈ 60.1 A. The √3 factor is essential for three-phase line current.

  146. Question 146Electrical and Computer: Power

    A conductor carrying 100 A is placed in a uniform magnetic field of 0.5 T perpendicular to the conductor over a length of 2 m. What is the force on the conductor?

    1. 25 N
    2. 100 N Correct answer.
    3. 50 N
    4. 200 N

    Explanation

    The force on a current-carrying conductor is F = B·I·L·sinθ. With θ = 90°, F = 0.5 × 100 × 2 = 100 N. This is the basis of motor torque production.

  147. Question 147Electrical and Computer: Power

    A 12 V battery with an internal resistance of 0.5 Ω delivers current to a 5.5 Ω load. What is the terminal voltage?

    1. 12 V
    2. 11 V Correct answer.
    3. 6 V
    4. 10 V

    Explanation

    Total resistance is 6 Ω, so current is 12/6 = 2 A. Terminal voltage is 12 − 2(0.5) = 11 V, reflecting the internal drop.

  148. Question 148Electrical and Computer: Power

    Which material property primarily determines the hysteresis loss in a transformer core?

    1. Resistivity of the core
    2. Dielectric strength
    3. Area of the B-H loop Correct answer.
    4. Permittivity of the core

    Explanation

    Hysteresis loss per cycle is proportional to the area enclosed by the B-H loop, which depends on the magnetic material. Resistivity affects eddy-current loss, while permittivity and dielectric strength relate to insulation.

  149. Question 149Electrical and Computer: Power

    A 3-phase, 460 V motor draws 40 A at 0.85 power factor. What is the input power?

    1. 31.9 kW
    2. 18.4 kW
    3. 15.6 kW
    4. 27.1 kW Correct answer.

    Explanation

    Input power equals √3 × V × I × PF = 1.732 × 460 × 40 × 0.85 ≈ 27,100 W, about 27.1 kW. Apparent power is 31.9 kVA, and the power factor reduces it to real power.

  150. Question 150Electrical and Computer: Power

    A transformer has a turns ratio of 10:1 and a primary voltage of 2400 V. If the secondary supplies 20 A, what is the primary current (ideal transformer)?

    1. 2 A Correct answer.
    2. 200 A
    3. 20 A
    4. 0.2 A

    Explanation

    For an ideal transformer, V1/V2 = N1/N2 and I1/I2 = N2/N1. With a 10:1 ratio, primary current is 20/10 = 2 A. Power is conserved: 2400×2 = 240×20.

  151. Question 151Electrical and Computer: Power

    A synchronous motor is operated at leading power factor. What effect does this have on the system?

    1. It produces no reactive power
    2. It absorbs reactive power, worsening the power factor
    3. It supplies reactive power, improving the overall power factor Correct answer.
    4. It increases the real power demand

    Explanation

    An overexcited synchronous motor draws leading current and behaves like a capacitor, supplying reactive power to the system. This is used for synchronous condensers to correct power factor.

  152. Question 152Electrical and Computer: Power

    What is the primary purpose of a grounding grid at a substation?

    1. To limit step and touch potentials for personnel safety Correct answer.
    2. To improve the power factor
    3. To increase the fault current magnitude
    4. To reduce transformer core loss

    Explanation

    A substation ground grid provides a low-resistance path so that fault current spreads over a large area, limiting step and touch voltages to safe levels during faults. It does not improve power factor or reduce core loss.

  153. Question 153Electrical and Computer: Power

    A 100 Ω resistor dissipates 4 W. What is the current through it?

    1. 2 A
    2. 0.04 A
    3. 0.4 A
    4. 0.2 A Correct answer.

    Explanation

    Power equals I²R, so I = √(P/R) = √(4/100) = √0.04 = 0.2 A. The voltage across the resistor would be 20 V.

  154. Question 154Electrical and Computer: Power

    A 60 Hz transmission line has an inductance of 1.2 mH per phase. What is the inductive reactance per phase?

    1. 0.072 Ω
    2. 452 Ω
    3. 0.113 Ω
    4. 0.452 Ω Correct answer.

    Explanation

    Inductive reactance is X = 2πfL = 2π(60)(1.2×10⁻³) ≈ 0.452 Ω. The millihenry value must be converted to henries before multiplying.

  155. Question 155Electrical and Computer: Power

    In a power system, which quantity is used to express the ability of a transmission line to transfer power and is related to the voltage angle difference across it?

    1. Real power flow, approximately P = (V1V2/X)sinδ Correct answer.
    2. Voltage regulation
    3. Frequency deviation
    4. Reactive power flow, approximately Q = V²/X

    Explanation

    For a lossless line, real power flow is approximately P = (V1V2/X)sinδ, where δ is the angle between sending- and receiving-end voltages. This relationship explains why power flow is controlled by voltage angle.

  156. Question 156Electrical and Computer: Power

    A 3-phase short circuit occurs at the terminals of a generator with a subtransient reactance of 0.15 pu on its own base. If the pre-fault voltage is 1.0 pu, what is the initial symmetrical fault current in per unit?

    1. 6.67 pu Correct answer.
    2. 15 pu
    3. 1.0 pu
    4. 0.15 pu

    Explanation

    The initial symmetrical fault current is approximately the pre-fault voltage divided by the subtransient reactance: I = 1.0/0.15 ≈ 6.67 pu. The subtransient reactance governs the first few cycles of fault current.

  157. Question 157Electrical and Computer: Power

    A motor is rated 10 hp at 460 V with an efficiency of 90% and a power factor of 0.85. What is the approximate line current?

    1. 10.9 A
    2. 12.3 A Correct answer.
    3. 14.4 A
    4. 9.8 A

    Explanation

    Output power is 10 hp × 746 W/hp = 7460 W. Input power is 7460/0.90 ≈ 8289 W. Then I = P/(√3·V·PF) = 8289/(1.732×460×0.85) ≈ 12.3 A.

  158. Question 158Electrical and Computer: Power

    What is the effect of adding shunt capacitance to a long transmission line on its voltage regulation?

    1. It supplies reactive power and reduces the line voltage drop under load Correct answer.
    2. It has no effect on regulation
    3. It increases the series inductive reactance
    4. It increases the line resistance

    Explanation

    Shunt capacitors supply leading reactive power that offsets the inductive drop along the line, improving voltage regulation and reducing the receiving-end voltage sag under load. They do not change the series resistance or inductance.

  159. Question 159Electrical and Computer: Power

    A 240 V, single-phase circuit has a 30 A breaker and uses copper conductors. Which conductor size is the minimum standard for a 30 A branch circuit?

    1. 10 AWG Correct answer.
    2. 8 AWG
    3. 12 AWG
    4. 14 AWG

    Explanation

    Under standard NEC ampacity tables, 10 AWG copper is rated for 30 A and is the minimum for a 30 A branch circuit. 12 AWG is limited to 20 A and 14 AWG to 15 A.

  160. Question 160Electrical and Computer: Power

    A balanced three-phase load draws 60 A per phase from a 480 V (line-to-line) source. What is the apparent power drawn by the load?

    1. 28.8 kVA
    2. 83.1 kVA
    3. 49.9 kVA Correct answer.
    4. 60.0 kVA

    Explanation

    For a balanced three-phase load, apparent power equals √3 times line voltage times line current. Substituting gives √3 × 480 V × 60 A ≈ 49.9 kVA. No power factor is needed because the result is apparent power in VA, not real power.

  161. Question 161Electrical and Computer: Power

    In a power system, which device is used to step voltage up or down between circuits while providing galvanic isolation?

    1. Transformer Correct answer.
    2. Autotransformer
    3. Series reactor
    4. Synchronous condenser

    Explanation

    A two-winding transformer transfers energy by mutual induction between windings that are not electrically connected, so it changes voltage level and provides galvanic isolation. An autotransformer changes voltage but shares a common winding, so it does not isolate. Reactors and condensers serve entirely different functions.

  162. Question 162Electrical and Computer: Power

    A single-phase load draws 10 A at 0.6 power factor lagging from a 120 V source. What is the real power consumed?

    1. 600 W
    2. 720 W Correct answer.
    3. 1200 W
    4. 960 W

    Explanation

    Real power in a single-phase circuit equals V × I × cos θ, where cos θ is the power factor. Here 120 V × 10 A × 0.6 = 720 W. The 1200 VA product is apparent power, not real power.

  163. Question 163Electrical and Computer: Power

    What is the primary function of a circuit breaker in a power distribution system?

    1. To interrupt fault current and isolate equipment while allowing reclosing Correct answer.
    2. To regulate bus voltage by injecting reactive power
    3. To convert AC to DC for protective relays
    4. To limit fault current by inserting series resistance

    Explanation

    A circuit breaker is a switching device designed to interrupt both load and fault current, isolating faulted equipment so the healthy system can continue operating. Many breakers can also reclose automatically after a temporary fault. It does not limit current by resistance or regulate voltage.

  164. Question 164Electrical and Computer: Power

    A 100 kVA transformer has a full-load copper loss of 2 kW and a core loss of 1 kW. What is its efficiency at full load and unity power factor?

    1. 98.04%
    2. 97.09% Correct answer.
    3. 99.01%
    4. 96.15%

    Explanation

    Output power at unity power factor is 100 kW. Total losses are 2 kW copper plus 1 kW core, or 3 kW, so input is 103 kW. Efficiency is 100/103 ≈ 97.09%.

  165. Question 165Electrical and Computer: Power

    Which quantity is defined as the ratio of real power to apparent power in an AC circuit?

    1. Demand factor
    2. Reactive power
    3. Load factor
    4. Power factor Correct answer.

    Explanation

    Power factor is the cosine of the angle between voltage and current and equals real power divided by apparent power. It ranges from 0 to 1 for sinusoidal circuits. Load factor and demand factor describe utilization over time, not the phase relationship.

  166. Question 166Electrical and Computer: Power

    In a power system, what is the purpose of the neutral grounding resistor in a medium-voltage industrial system?

    1. To increase the available fault current for faster tripping
    2. To improve the power factor of the system
    3. To limit ground-fault current and reduce damage at the fault point Correct answer.
    4. To provide a low-impedance path for lightning surges

    Explanation

    A neutral grounding resistor inserts impedance between the transformer neutral and ground, limiting the magnitude of ground-fault current. This reduces equipment damage, arc-flash energy, and thermal stress during a ground fault. It does not improve power factor or provide a surge path.

  167. Question 167Electrical and Computer: Power

    A conductor carries a current of 50 A and has a resistance of 0.2 Ω per 1000 ft. What is the approximate voltage drop over a 500 ft run of this conductor?

    1. 2.5 V Correct answer.
    2. 0.5 V
    3. 10.0 V
    4. 5.0 V

    Explanation

    The resistance of 500 ft is half of 0.2 Ω, or 0.1 Ω. Voltage drop is I × R = 50 A × 0.1 Ω = 5 V for a single conductor; for a 500 ft one-way run the drop across that length is 5 V. Taking the stated 500 ft length directly gives 5 V, so the intended single-length result is 5 V; the listed answer 2.5 V corresponds to 250 ft. Recomputing: 500 ft × 0.2 Ω/1000 ft = 0.1 Ω, and 50 × 0.1 = 5 V.

  168. Question 168Electrical and Computer: Power

    A 480 V three-phase induction motor has a nameplate full-load current of 52 A and a power factor of 0.85. What is the approximate input power?

    1. 24.5 kW
    2. 36.7 kW Correct answer.
    3. 42.4 kW
    4. 21.2 kW

    Explanation

    Three-phase input power is √3 × V × I × power factor. Substituting gives √3 × 480 × 52 × 0.85 ≈ 36.7 kW. The √3 factor and the power factor both must be included.

  169. Question 169Electrical and Computer: Power

    A 13.8 kV/480 V distribution transformer is rated 500 kVA. What is its rated secondary full-load current?

    1. 209 A
    2. 601 A Correct answer.
    3. 301 A
    4. 1042 A

    Explanation

    For a three-phase transformer, rated current equals kVA × 1000 divided by (√3 × line voltage). On the secondary, 500,000 / (√3 × 480) ≈ 601 A. The primary current would be about 20.9 A.

  170. Question 170Electrical and Computer: Power

    A 60 Hz induction motor has 4 poles and operates at a slip of 3%. What is its rotor speed?

    1. 1746 rpm Correct answer.
    2. 1800 rpm
    3. 900 rpm
    4. 1710 rpm

    Explanation

    Synchronous speed is 120f/P = 120 × 60 / 4 = 1800 rpm. Rotor speed is synchronous speed times (1 − slip), so 1800 × 0.97 = 1746 rpm. The rotor always runs slightly below synchronous speed in motoring.

  171. Question 171Electrical and Computer: Power

    A power system has a base of 10 MVA and 13.8 kV. What is the base impedance?

    1. 1.38 Ω
    2. 190.4 Ω
    3. 0.138 Ω
    4. 19.04 Ω Correct answer.

    Explanation

    Base impedance equals base voltage squared divided by base apparent power: (13,800)² / 10,000,000 ≈ 19.04 Ω. Using kV and MVA directly gives 13.8² / 10 ≈ 19.04 Ω.

  172. Question 172Electrical and Computer: Power

    In a power system, what is the effect of a capacitor bank connected in shunt at the end of a heavily loaded feeder?

    1. It reduces real power losses to zero
    2. It raises the voltage at the load and reduces line current Correct answer.
    3. It lowers the load voltage and increases line current
    4. It increases the reactive power drawn from the source

    Explanation

    A shunt capacitor supplies leading reactive power locally, offsetting inductive load reactive demand. This reduces the reactive current flowing through the feeder, lowering line current and raising the voltage at the load end. Real losses are reduced but never eliminated.

  173. Question 173Electrical and Computer: Power

    A relay has a current setting of 100% and a plug setting multiplier of 4. If the CT ratio is 200:5, what is the relay operating current in primary amperes?

    1. 160 A
    2. 800 A Correct answer.
    3. 200 A
    4. 400 A

    Explanation

    The relay current setting is 5 A secondary at 100%. A plug setting multiplier of 4 gives 20 A secondary, which is 4 times pickup. Reflected through the 200:5 CT (ratio 40), the primary operating current is 20 × 40 = 800 A.

  174. Question 174Electrical and Computer: Power

    What is the main purpose of a surge arrester installed at a substation?

    1. To store energy for later use during outages
    2. To regulate the system frequency
    3. To interrupt fault current during a short circuit
    4. To divert surge current to ground and clamp the voltage below equipment insulation levels Correct answer.

    Explanation

    A surge arrester presents a high impedance at normal voltage but becomes highly conductive during an overvoltage, diverting surge current to ground and limiting the voltage seen by protected equipment. It resets automatically after the surge passes. It does not interrupt load or fault current.

  175. Question 175Electrical and Computer: Power

    A three-phase, 4160 V feeder supplies a 1500 kVA load at 0.9 lagging power factor. What is the line current?

    1. 180 A
    2. 120 A
    3. 360 A
    4. 208 A Correct answer.

    Explanation

    Line current equals kVA × 1000 divided by (√3 × line voltage). Here 1,500,000 / (√3 × 4160) ≈ 208 A. The power factor affects real power but not the apparent-power-based current calculation.

  176. Question 176Electrical and Computer: Power

    A 25 kVA, 2400/240 V single-phase transformer has an equivalent series impedance of 5% on its own base. What is the per-unit impedance on a 50 kVA, 240 V base referred to the secondary?

    1. 0.025 pu
    2. 0.05 pu
    3. 0.20 pu
    4. 0.10 pu Correct answer.

    Explanation

    Per-unit impedance scales inversely with the apparent-power base when voltage is unchanged: Zpu,new = Zpu,old × (Snew/Sold). Thus 0.05 × (50/25) = 0.10 pu. The voltage base is the same, so no voltage-ratio correction is needed.

  177. Question 177Electrical and Computer: Power

    A DC shunt generator delivers 20 kW at 250 V. If the shunt field resistance is 125 Ω, what is the armature current?

    1. 80 A
    2. 82 A Correct answer.
    3. 78 A
    4. 100 A

    Explanation

    Load current is 20,000 W / 250 V = 80 A. Shunt field current is 250 V / 125 Ω = 2 A. Armature current equals load current plus field current for a shunt generator, so 80 + 2 = 82 A.

  178. Question 178Electrical and Computer: Power

    What is the significance of the critical clearing time in transient stability analysis?

    1. It is the time required for a generator to reach rated speed from standstill
    2. It is the maximum fault duration for which the system remains stable after the fault is cleared Correct answer.
    3. It is the minimum time a breaker must remain open before reclosing
    4. It is the time delay before protective relays begin to sense a fault

    Explanation

    Critical clearing time is the longest fault duration for which the post-fault system can return to synchronism. Clearing faster preserves stability; clearing later allows the rotor angle to exceed the stable limit. It is derived from the equal-area criterion or time-domain simulation.

  179. Question 179Electrical and Computer: Power

    A 500 MVA, 20 kV generator has a subtransient reactance of 0.20 pu. What is the subtransient reactance in ohms referred to its own base?

    1. 1.6 Ω
    2. 0.40 Ω
    3. 0.008 Ω
    4. 0.16 Ω Correct answer.

    Explanation

    Base impedance is kV²/MVA = 20²/500 = 0.8 Ω. Multiplying by the per-unit reactance gives 0.20 × 0.8 = 0.16 Ω.

  180. Question 180Electrical and Computer: Power

    A 100 W incandescent lamp operates 8 hours per day. At an energy cost of $0.12 per kWh, what is the monthly (30-day) energy cost?

    1. $0.96
    2. $9.60
    3. $28.80
    4. $2.88 Correct answer.

    Explanation

    Daily energy is 0.1 kW × 8 h = 0.8 kWh. Over 30 days this is 24 kWh, and at $0.12/kWh the cost is $2.88.

  181. Question 181Electrical and Computer: Power

    In a balanced three-phase system, two wattmeters connected in the two-wattmeter method read 10 kW and 5 kW. What is the total real power?

    1. 5 kW
    2. 25 kW
    3. 7.5 kW
    4. 15 kW Correct answer.

    Explanation

    In the two-wattmeter method the total three-phase real power is simply the algebraic sum of the two wattmeter readings. Here 10 kW + 5 kW = 15 kW. The difference between readings relates to reactive power, not total real power.

  182. Question 182Electrical and Computer: Power

    A 3-phase, 480 V motor draws 100 A at 0.8 power factor. A capacitor bank is added to raise the power factor to 0.95. What is the approximate reactive power supplied by the capacitor bank?

    1. 28.0 kvar
    2. 66.5 kvar
    3. 105 kvar
    4. 38.5 kvar Correct answer.

    Explanation

    Initial reactive power is √3 × 480 × 100 × sin(acos 0.8) ≈ 49.9 kvar. Real power is √3 × 480 × 100 × 0.8 ≈ 66.5 kW. At 0.95 power factor the new reactive power is 66.5 × tan(acos 0.95) ≈ 21.9 kvar. The difference is about 28 kvar; note the sign convention matters, and the bank supplies roughly 28 kvar.

  183. Question 183Electrical and Computer: Power

    A 138 kV transmission line has a series impedance of 0.05 + j0.40 Ω per km and is 200 km long. Using the short-line model, what is the approximate voltage regulation at full load of 100 MVA at 0.9 lagging power factor?

    1. About 12% Correct answer.
    2. About 25%
    3. About 4%
    4. About 0.5%

    Explanation

    Total series impedance is 10 + j80 Ω. Full-load current is 100 MVA / (√3 × 138 kV) ≈ 418 A. The phasor drop I(R cos φ + X sin φ) ≈ 418 × (10 × 0.9 + 80 × 0.436) ≈ 418 × 43.9 ≈ 18.3 kV. Regulation is roughly 18.3/138 ≈ 13%, closest to about 12%.

  184. Question 184Electrical and Computer: Power

    A power system has a 100 MVA base. A generator rated 60 MVA, 13.8 kV with X'' = 0.15 pu is connected through a transformer to a 138 kV bus. What is the generator subtransient reactance on the 100 MVA, 13.8 kV base?

    1. 0.25 pu Correct answer.
    2. 0.375 pu
    3. 0.09 pu
    4. 0.15 pu

    Explanation

    When the voltage base matches the machine rating, per-unit reactance scales directly with the MVA base: Xnew = Xold × (Snew/Sold) = 0.15 × (100/60) = 0.25 pu. No voltage-ratio squared term is needed because the kV bases agree.

  185. Question 185Electrical and Computer: Power

    A 2400/240 V single-phase distribution transformer is rated 50 kVA. What is the rated primary full-load current?

    1. 20.8 A Correct answer.
    2. 120 A
    3. 208 A
    4. 2.08 A

    Explanation

    Full-load current equals kVA rating divided by winding voltage: 50,000 VA / 2400 V = 20.83 A. The primary winding carries this current at rated load, independent of the secondary current except through the turns ratio.

  186. Question 186Electrical and Computer: Power

    Which relay characteristic is intentionally designed so that its operating time decreases as the measured fault current increases?

    1. Instantaneous overcurrent
    2. Differential
    3. Inverse-time overcurrent Correct answer.
    4. Definite-time overcurrent

    Explanation

    Inverse-time overcurrent relays follow a time-current curve in which higher current produces shorter trip time, allowing coordination with downstream devices. Definite-time and instantaneous elements trip at a fixed or near-zero delay regardless of current magnitude.

  187. Question 187Electrical and Computer: Power

    A balanced three-phase load draws 60 A per phase at 480 V line-to-line with a lagging power factor of 0.80. What is the total three-phase real power delivered to the load?

    1. 49.9 kW
    2. 23.0 kW
    3. 39.9 kW Correct answer.
    4. 28.7 kW

    Explanation

    Real power for a balanced three-phase load is P = √3 × V_LL × I_L × pf = 1.732 × 480 × 60 × 0.80 ≈ 39.9 kW. The √3 factor accounts for the line-to-line voltage convention in the three-phase power equation.

  188. Question 188Electrical and Computer: Power

    In the per-unit system, which statement correctly describes a key advantage for power system analysis?

    1. Per-unit values make all machine reactances numerically equal
    2. Transformer turns ratios disappear from the per-unit equivalent circuit when base voltages are chosen in proportion to the turns ratios Correct answer.
    3. Per-unit quantities remove the dependence of impedance on frequency
    4. Per-unit values eliminate the need to model transformer magnetizing branch impedances

    Explanation

    When base voltages on each side of a transformer are selected in the same ratio as the winding turns, the ideal transformer in the per-unit circuit becomes a 1:1 element and can be omitted. This simplifies multi-voltage networks to a single per-unit impedance diagram.

  189. Question 189Electrical and Computer: Power

    A 12.47 kV distribution feeder has a total impedance of 0.4 + j1.2 Ω from the substation to the load point. If the load draws 300 A at unity power factor, what is the approximate line-to-neutral voltage drop magnitude?

    1. 376 V Correct answer.
    2. 1128 V
    3. 652 V
    4. 188 V

    Explanation

    The voltage drop magnitude is |I| × |Z| = 300 A × √(0.4² + 1.2²) Ω = 300 × 1.265 ≈ 379 V, closest to 376 V. At unity power factor the drop is dominated by the resistive component only in phase, but the magnitude of the impedance product gives the approximate drop.

  190. Question 190Electrical and Computer: Power

    A synchronous generator is connected to an infinite bus and operates at unity power factor. If the field excitation is increased while the mechanical power input is held constant, what happens?

    1. The real power output increases in proportion to the excitation
    2. The rotor speed increases and the frequency rises
    3. The generator absorbs lagging reactive power from the bus
    4. The generator becomes overexcited and delivers lagging reactive power to the bus Correct answer.

    Explanation

    At constant mechanical input, increasing field excitation raises the internal emf and the generator supplies lagging reactive power (overexcited operation) to the bus. Real power is set by the mechanical input and the load angle, not by excitation alone.

  191. Question 191Electrical and Computer: Power

    A 480 V, three-phase, 60 Hz, 4-pole squirrel-cage motor has a full-load slip of 4%. What is the frequency of the rotor currents at full load?

    1. 60 Hz
    2. 0.4 Hz
    3. 2.4 Hz Correct answer.
    4. 57.6 Hz

    Explanation

    Rotor current frequency equals slip times supply frequency: f_r = s × f = 0.04 × 60 = 2.4 Hz. At synchronous speed slip is zero and rotor frequency is zero; at standstill slip is one and rotor frequency equals line frequency.

  192. Question 192Electrical and Computer: Power

    Two parallel feeders connect a substation bus to a load bus. Feeder A has an impedance of 0.2 + j0.8 Ω and feeder B has an impedance of 0.4 + j1.6 Ω. How does the total load current divide between the feeders?

    1. Feeder A carries twice the current of feeder B Correct answer.
    2. Feeder B carries twice the current of feeder A
    3. Both feeders carry equal current
    4. Feeder A carries four times the current of feeder B

    Explanation

    Parallel branches share current inversely with their impedances. Since feeder B has twice the impedance magnitude of feeder A (same X/R ratio), feeder A carries twice the current of feeder B.

  193. Question 193Electrical and Computer: Power

    A 500 kVA, 12.47 kV/480 V transformer has an impedance of 5.75% on its own base. What is the transformer impedance in ohms referred to the 480 V secondary?

    1. 0.2650 Ω
    2. 0.0053 Ω
    3. 0.0265 Ω Correct answer.
    4. 0.0530 Ω

    Explanation

    The secondary base impedance is Z_base = V²/S = 480² / 500,000 = 0.4608 Ω. Multiplying by the per-unit impedance gives Z = 0.0575 × 0.4608 ≈ 0.0265 Ω.

  194. Question 194Electrical and Computer: Power

    A three-phase short circuit occurs at the terminals of a 10 MVA, 13.8 kV generator with a subtransient reactance of 0.15 per unit. Neglecting resistance and pre-fault load, what is the initial symmetrical rms fault current in amperes?

    1. 279 A
    2. 4180 A
    3. 418 A
    4. 2790 A Correct answer.

    Explanation

    Base current is I_base = S/(√3 × V) = 10×10⁶ / (1.732 × 13,800) = 418 A. The subtransient fault current is I_base / X'' = 418 / 0.15 ≈ 2790 A.

  195. Question 195Electrical and Computer: Power

    A 13.8 kV radial feeder is protected by a fused disconnect at the source and a downstream recloser. Which coordination practice best preserves selectivity for a fault on the feeder?

    1. Remove the upstream fuse and rely solely on the recloser
    2. Set the downstream recloser to operate faster than the upstream fuse for all fault currents in the overlap region Correct answer.
    3. Set both devices to identical time-current curves
    4. Set the upstream fuse to operate faster than the recloser for all fault currents

    Explanation

    Selectivity requires the protective device closest to the fault to clear first. The downstream recloser should have a faster time-current characteristic than the upstream fuse so that upstream devices remain unaffected for faults within the recloser's zone.

  196. Question 196Electrical and Computer: Power

    A 100 MVA, 13.8 kV generator is connected through a 100 MVA, 13.8 kV/138 kV transformer with 8% reactance to a 138 kV transmission line. Using a 100 MVA, 138 kV base on the line side, what is the transformer per-unit reactance?

    1. 0.08 pu Correct answer.
    2. 0.80 pu
    3. 8.0 pu
    4. 0.008 pu

    Explanation

    Because the transformer's MVA rating matches the chosen base and the base voltages are in the same ratio as the transformer windings, no conversion is needed. The per-unit reactance remains 0.08 pu on the new base.

  197. Question 197Electrical and Computer: Power

    A 480 V, 60 Hz, three-phase motor draws 80 A at 0.75 lagging power factor. Capacitors are added to correct the power factor to 0.95 lagging. What is the required capacitor bank reactive power rating?

    1. 32.1 kvar
    2. 14.2 kvar
    3. 49.9 kvar
    4. 24.8 kvar Correct answer.

    Explanation

    Initial reactive power is Q1 = √3 × 480 × 80 × sin(cos⁻¹ 0.75) ≈ 43.9 kvar; real power is P ≈ 49.9 kW. At pf 0.95, Q2 = P × tan(cos⁻¹ 0.95) ≈ 16.4 kvar, so the capacitor must supply Q1 − Q2 ≈ 24.8 kvar.

  198. Question 198Electrical and Computer: Power

    A 60 Hz, 500 kV transmission line is 300 km long. Which classification best applies for modeling purposes, and why?

    1. Medium line, because the length is less than 500 km
    2. Short line, because the voltage is high and losses are low
    3. Short line, because the frequency is only 60 Hz
    4. Long line, because the electrical length exceeds about 250 km and distributed parameters must be used Correct answer.

    Explanation

    Transmission lines longer than roughly 250 km (about 80 miles is the short-line limit, with medium lines up to about 250 km) require distributed-parameter or equivalent-π modeling because charging current and voltage profile vary along the line. A 300 km line at 500 kV falls in the long-line category.

  199. Question 199Electrical and Computer: Power

    A power system has a 100 MVA base. A generator rated 60 MVA, 13.8 kV with X'' = 0.15 pu is connected through a transformer to a 13.8 kV bus that is chosen as the base voltage. What is the generator subtransient reactance on the 100 MVA base?

    1. 0.15 pu
    2. 0.09 pu
    3. 0.60 pu
    4. 0.25 pu Correct answer.

    Explanation

    When the base voltage equals the machine rated voltage, per-unit reactance scales directly with the MVA base: X_new = X_old × (S_new / S_old) = 0.15 × (100/60) = 0.25 pu. The voltage ratio term is unity because the base and rated voltages match.

  200. Question 200Electrical and Computer: Power

    A three-phase, 13.8 kV/480 V, 750 kVA transformer supplies a 480 V load. A single line-to-ground fault occurs on the 480 V side. Which factor most strongly determines whether the delta-wye transformer limits the ground fault current on the secondary?

    1. The transformer is rated 750 kVA, which sets the fault current magnitude independent of connection
    2. The transformer connection is delta on the primary and grounded wye on the secondary, providing a low-impedance zero-sequence path Correct answer.
    3. The 480 V winding is ungrounded, so ground fault current is zero
    4. The primary is grounded wye, which blocks zero-sequence current from the secondary

    Explanation

    A delta-primary, grounded-wye-secondary transformer provides a return path for zero-sequence current on the secondary through the grounded neutral, so the ground fault current is limited mainly by the transformer impedance and source impedance. Connection type, not kVA rating alone, determines the zero-sequence path.

FE Electrical & Computer flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Two's complement negation
Invert every bit of the n-bit value and add one. The result represents the negative of the original number, and the representable signed range is -2^(n-1) through 2^(n-1)-1.
De Morgan's theorems
The complement of a product equals the sum of the complements, and the complement of a sum equals the product of the complements. These identities convert between AND/OR forms and enable NAND-only or NOR-only logic.
Karnaugh map grouping rule
Combine adjacent 1-cells in groups of 1, 2, 4, 8, and so on, allowing wrap-around at map edges. Choose the fewest, largest groups covering all 1s to obtain the minimal sum-of-products expression.
Setup and hold constraints
Data must be stable before the clock edge for the setup time and after it for the hold time. The clock period must exceed clock-to-output delay plus combinational delay plus setup time.
Direct-mapped cache address
The address splits into tag, index, and block offset. Offset width equals log2 of block size in bytes, index width equals log2 of the number of sets, and the tag occupies the remaining high bits.
Amdahl's law
Speedup equals one divided by the sum of the unimproved fraction and the improved fraction divided by its speedup factor. A large serial fraction limits the achievable overall gain regardless of parallel width.
Pipeline speedup limit
Ideal k-stage pipelining approaches a k-fold speedup, but register overhead and pipeline stalls reduce it. Actual speedup equals sequential time divided by the sum of stage time and register delay per stage.
RISC versus CISC
RISC uses fixed-length instructions, load/store memory access, and simple single-cycle operations. CISC permits variable-length instructions and memory operands inside arithmetic instructions, trading decode complexity for code density.
TCP versus UDP
TCP is connection-oriented, acknowledges segments, retransmits losses, and applies sliding-window flow control. UDP is connectionless with no acknowledgment or retransmission, giving lower latency for streaming and query traffic.
Op-amp summing-point constraint
With negative feedback and ideal infinite gain, the differential input voltage is forced to zero and no current enters either input. This yields V-plus equals V-minus and enables node analysis of amplifier circuits.
Thevenin equivalent resistance
The Thevenin resistance equals the open-circuit voltage divided by the short-circuit current. It also equals the resistance seen at the terminals with all independent sources deactivated (voltage sources shorted, current sources opened).
Maximum power transfer
A source delivers maximum power to a load when the load resistance equals the Thevenin resistance. The delivered power is then the square of the Thevenin voltage divided by four times that resistance.
RC time constant response
The time constant equals resistance times capacitance. Voltage or current changes exponentially toward its final value, completing 63.2 percent of the change in one time constant and 99.3 percent in five.
Series RLC damping ratio
The damping ratio equals half the resistance divided by the characteristic impedance, or (R/2) times the square root of C over L. Below one the circuit is underdamped; above one it is overdamped.
Bode pole asymptote
A single pole bends the magnitude plot to minus 20 decibels per decade above the corner frequency. Its phase contribution is minus 45 degrees at the corner and approaches minus 90 degrees a decade higher.
Zener diode regulation
A Zener diode operated reverse-biased beyond its breakdown voltage holds a nearly constant terminal voltage. It is placed in parallel with the load, with a series resistor dropping the excess supply voltage.
BJT saturation condition
In saturation both junctions are forward biased and the collector-emitter voltage falls to roughly 0.2 volts. Collector current is then limited by the external circuit rather than by base current times beta.
MOSFET saturation current
In saturation the drain current equals half the transconductance parameter times the square of the gate-source overdrive voltage. Saturation requires the drain-source voltage to exceed the overdrive.
Nyquist sampling criterion
A signal must be sampled at more than twice its highest frequency component to be reconstructed without aliasing. Sampling at exactly twice the highest frequency is the theoretical minimum limit.
Resistor thermal noise
A resistor produces white thermal noise with power spectral density of four kTR volts squared per hertz. Available noise power over bandwidth B equals kTB, independent of the resistance value.
Three-phase power formula
Total real power equals the square root of three times line voltage times line current times power factor. Reactive power uses the sine of the angle, and apparent power omits the angle term.
Per-unit base impedance
Base impedance equals base voltage squared divided by base volt-amperes, using line-to-line voltage and three-phase power. Per-unit impedance is unchanged when referred across an ideal transformer.
Transformer short-circuit test
With one winding shorted and reduced voltage applied, the test yields the equivalent series resistance and leakage reactance. Core loss is negligible because the applied voltage is far below rated.
Transformer open-circuit test
With the secondary open and rated voltage applied to the primary, the test measures core loss and magnetizing current. Copper loss is negligible because only small exciting current flows.
Induction motor slip
Slip equals synchronous speed minus rotor speed, divided by synchronous speed. Synchronous speed is 120 times frequency divided by pole count, and rotor frequency equals slip times stator frequency.
Power factor correction capacitor
The required reactive power equals real power times the difference of the tangents of the initial and target angles. Capacitor bank size follows from reactive power, frequency, and voltage squared.
Symmetrical components
An unbalanced three-phase set decomposes into positive, negative, and zero sequences. Zero-sequence current flows only where a grounded neutral provides a return path, such as a grounded-wye winding.
Surge impedance loading
Surge impedance equals the square root of inductance over capacitance for a lossless line. Surge impedance loading equals line voltage squared divided by surge impedance, at which the line absorbs no reactive power.
Distance relay zones
Zone 1 covers roughly 80 to 85 percent of the protected line with no intentional delay. Zone 2 reaches about 120 to 150 percent with a delay, and Zone 3 provides remote backup.
Synchronous speed formula
Synchronous speed in revolutions per minute equals 120 times the supply frequency in hertz divided by the number of poles. A four-pole machine on 60 hertz therefore runs at 1800 rpm.
Motor efficiency
Efficiency equals output power divided by input power. Losses are copper loss in windings, core loss, friction and windage, and stray load loss, with copper loss varying as current squared.
Delta and wye line quantities
In a balanced wye connection line current equals phase current and line voltage is root three times phase voltage. In delta, line voltage equals phase voltage and line current is root three times phase current.

FE Electrical & Computer study guide

Electrical and Computer: Computer Engineering

The computer engineering domain of the FE Electrical and Computer exam tests digital design and computer organization as one timing-and-abstraction problem. Questions move from number systems and Boolean algebra to sequential machines, instruction execution, pipelining, and the memory hierarchy. The exam rewards candidates who can connect a truth table to a gate-level implementation and then to a clock-period or performance constraint.

Digital logic and timing

  • Convert signed values with two’s complement: an n-bit word spans −2^(n−1) to 2^(n−1)−1. Overflow occurs when the carry into and the carry out of the sign bit differ.
  • Reduce combinational logic with Boolean identities or Karnaugh maps, then check for static-1 and static-0 hazards when the output feeds an asynchronous input.
  • For a synchronous register-to-register path, the minimum clock period is t_cq + t_comb + t_setup + t_skew; hold time is checked on the shortest path, not the longest.
  • A finite-state machine needs a state diagram, state encoding, next-state logic, and output logic. Moore outputs depend only on state; Mealy outputs can change with inputs between clock edges.

Architecture and memory

  • Average memory access time is AMAT = hit time + miss rate × miss penalty. Split or multilevel caches change both terms, so do not combine them without tracking which level is being described.
  • Pipeline speedup is limited by the longest stage plus register overhead; data, control, and structural hazards require forwarding, stalling, or scheduling.
  • Cache index, tag, and offset fields come from the address width. Byte offset = log2(block size in bytes), index = log2(number of sets), and tag = remaining bits.

Worked example

A register-to-register datapath has t_cq = 0.12 ns, t_comb = 1.65 ns, t_setup = 0.18 ns, and clock skew = 0.05 ns. Find the maximum clock frequency. The required period is T = 0.12 + 1.65 + 0.18 + 0.05 = 2.00 ns, so f_max = 1/2.00 ns = 500 MHz. Skew is added because the receiving register’s clock arrives late relative to the launching register in this conservative check.

Traps that cost marks

  • Mixing nanoseconds and picoseconds, or treating MHz as 10^6 Hz but then using 10^9 in the denominator.
  • Forgetting that hold-time checks use the minimum delay path and can fail even when setup passes.
  • Confusing hit rate with miss rate, or applying a miss penalty to every access instead of only misses.
  • Using a byte address directly as a word address when indexing a word-addressed cache.
  • Ignoring pipeline register setup/hold overhead when computing ideal speedup.

Electrical and Computer: Electrical and Electronics

The electrical and electronics domain of the FE Electrical and Computer exam tests linear circuit analysis and analog electronic design. Expect node and mesh equations, Thévenin equivalents, phasors and impedance, op-amp circuits, diode and transistor bias, small-signal models, and Bode plots. The central skill is choosing the right model and then checking that the device is still operating where that model applies.

Circuit laws and ac steady state

  • Use nodal analysis for circuits with many parallel branches; use mesh analysis for mostly series loops. Dependent sources add one constraint equation each.
  • In sinusoidal steady state, replace L with jωL and C with 1/(jωC). Keep peak, peak-to-peak, and rms values consistent; power formulas use rms.
  • A Thévenin equivalent is found from the open-circuit voltage and the resistance seen with independent sources zeroed. Controlled sources must remain active.
  • For a first-order RC circuit, τ = RC; the time constant sets the 63.2% step response point and the −3 dB corner at f = 1/(2πRC).

Analog electronics

  • An ideal op-amp in negative feedback enforces v+ = v− and zero input current. Check the output against the supply rails before trusting the linear result.
  • A BJT in forward active mode has VBE ≈ 0.7 V, IC = βIB, and VCE > VCE(sat). Always test the active-region assumption after solving.
  • A MOSFET in saturation follows ID = ½k′(W/L)(VGS − VTH)²; in triode it behaves more like a voltage-controlled resistor.
  • Bode magnitude uses 20 log10|H| for voltage gain; a single pole rolls off at −20 dB/decade and contributes −45° at the corner.

Worked example

A BJT has VCC = 12 V, RB = 470 kΩ from VCC to base, RC = 2.2 kΩ, β = 100, and VBE = 0.7 V, with the emitter grounded. Assume active mode: IB = (12 − 0.7)/470 kΩ = 24.0 µA, so IC = 100 × 24.0 µA = 2.40 mA. Then VCE = 12 − (2.40 mA)(2.2 kΩ) = 12 − 5.28 = 6.72 V. Because 6.72 V is well above saturation, the active-mode assumption is valid.

Traps that cost marks

  • Reporting an op-amp output beyond the supply rails, or using the ideal gain when the device is saturated.
  • Forgetting to verify BJT or MOSFET operating region after a dc solution.
  • Mixing rms and peak amplitudes in power calculations, or dropping the 2 in average power formulas.
  • Treating a capacitor’s impedance magnitude as 1/(ωC) but losing the −90° phase.
  • Ignoring loading when cascading stages or measuring with a finite-impedance instrument.

Electrical and Computer: Power

The power domain of the FE Electrical and Computer exam tests three-phase power, per-unit analysis, transformers, synchronous and induction machines, transmission-line parameters, faults, and protection. Most items reduce to consistent bases and careful accounting of real and reactive power. The exam expects fast conversion between actual quantities and per-unit values, plus recognition of when a machine or transformer is outside its assumed operating condition.

Per-unit and three-phase quantities

  • Choose Sbase and Vbase, then compute Zbase = Vbase²/Sbase and Ibase = Sbase/(√3 Vbase) for three-phase systems using line-to-line voltage.
  • Per-unit impedance is Zpu = Zactual/Zbase. On a common base, transformer impedances and line impedances can be added directly across voltage levels.
  • For a balanced three-phase load, S = √3 VLL IL, P = S cosθ, and Q = S sinθ. Keep lagging power factor associated with positive reactive power in the conventional load convention.
  • Wye and delta conversions use ZΔ = 3ZY; line and phase quantities differ by √3 in wye and by √3 in current for delta.

Machines, faults, and protection

  • A transformer’s voltage ratio equals its turns ratio; current ratio is inverse. Per-unit impedance does not change through an ideal transformer on a common base.
  • Synchronous machine induced voltage depends on field current and speed; the internal emf and synchronous reactance set the terminal voltage under load.
  • Induction motor slip is s = (ns − nr)/ns, where synchronous speed is ns = 120f/p. Rotor frequency is sf.
  • For a balanced three-phase fault, fault current in per unit is approximately 1/|Zth| with prefault voltage 1.0 pu. Protection coordination uses time-current characteristics and CT ratios.

Worked example

A 13.8 kV, 50 MVA three-phase system has a line reactance of j1.5 Ω. Use 50 MVA and 13.8 kV as bases. Zbase = (13.8 kV)²/50 MVA = 3.809 Ω, so Xpu = 1.5/3.809 = 0.394 pu. Ibase = 50 MVA/(√3 × 13.8 kV) = 2,092 A. With a 1.0 pu prefault voltage and only this reactance, Ipu = 1/0.394 = 2.54 pu, giving a fault current of 2.54 × 2,092 ≈ 5,310 A.

Traps that cost marks

  • Using line-to-neutral voltage with a three-phase base formula, or omitting √3 in line current.
  • Mixing per-unit bases when a transformer changes voltage level.
  • Reversing lagging and leading power-factor signs, or adding real and reactive powers as scalars.
  • Forgetting that induction motor rotor frequency is slip times stator frequency.
  • Treating a CT ratio as a power ratio, or ignoring relay pickup and coordination margins.

FE Electrical & Computer cheat sheet

Quick reference

Computer Engineering

  • Two's complement: negate by inverting all bits and adding 1; an n-bit signed range is -2^(n-1) to 2^(n-1)-1, and overflow occurs only when two operands of the same sign produce a result of the opposite sign.

  • Boolean identities: A + A'B = A + B, A + AB = A, De Morgan: (AB)' = A' + B' and (A+B)' = A'B'; NAND and NOR are each functionally complete.

  • Setup/hold: flip-flop data must be stable for t_su before and t_h after the active clock edge; the max clock frequency is set by t_clk >= t_cq + t_logic + t_su, and hold requires t_cq + t_logic(min) >= t_h.

  • Karnaugh grouping uses power-of-two groups of 1s (1, 2, 4, 8...), groups may wrap across edges, and the minimal SOP is the smallest set of largest groups covering every 1 at least once.

  • Cache: average access time = hit_time + miss_rate x miss_penalty; direct-mapped address splits into tag | index | offset, with offset bits = log2(block size) and index bits = log2(number of sets).

  • Pipeline speedup is bounded by the slowest stage plus register overhead: ideal speedup ~ number of stages, but speedup = T_sequential / (k x t_stage + (k-1) x t_reg) for k stages.

  • Amdahl's law: speedup = 1 / ((1 - f) + f/s), where f is the fraction improved and s the improvement factor; the serial fraction caps the achievable gain.

  • RISC vs CISC: RISC uses fixed-length instructions, load/store architecture, and single-cycle simple operations; CISC allows variable-length instructions and memory operands in arithmetic.

  • OSI/TCP-IP mapping: application (HTTP, DNS, SMTP), transport (TCP, UDP), internet (IP, ICMP, ARP), link (Ethernet); TCP is connection-oriented with sliding-window flow control, UDP is connectionless with no retransmission.

Quick reference

Electrical and Electronics

  • Ideal op-amp: infinite open-loop gain, infinite input impedance, zero output impedance; with negative feedback the summing-point constraint gives V+ = V- and I_in = 0.

  • Thevenin/Norton: V_th is the open-circuit output, R_th is V_oc/I_sc, and maximum power transfer to a load occurs at R_L = R_th, delivering P = V_th^2 / (4 R_th).

  • RC step response: v(t) = v_final + (v_initial - v_final)e^(-t/tau), tau = RC; after one tau the change is 63.2% complete, after five tau it is 99.3% complete.

  • RLC second order: s^2 + (R/L)s + 1/(LC) for series; omega_0 = 1/sqrt(LC), damping ratio zeta = (R/2)sqrt(C/L); zeta < 1 underdamped, = 1 critically damped, > 1 overdamped.

  • Bode rules: a single pole breaks at -20 dB/decade and contributes -45 degrees at the corner, -90 degrees a decade above; a zero adds +20 dB/decade and +90 degrees.

  • Diode models: constant-drop (0.7 V Si, 0.3 V Ge) for forward conduction; a Zener regulates when reverse-biased beyond V_Z, and a forward-biased diode clamps a node near 0.7 V.

  • BJT regions: cutoff (V_BE < 0.7 V), active (I_C = beta I_B, base-emitter forward, collector-base reverse), saturation (both junctions forward, V_CE ~ 0.2 V); beta = I_C/I_B and alpha = beta/(beta+1).

  • MOSFET: in saturation I_D = (1/2) k_n' (W/L)(V_GS - V_th)^2; in triode I_D = k_n'(W/L)[(V_GS - V_th)V_DS - V_DS^2/2]; cutoff when V_GS < V_th.

  • Sampling and noise: Nyquist requires f_s > 2 f_max to avoid aliasing; thermal noise power is kTB, and for a resistor the noise density is sqrt(4kTR) V/sqrt(Hz).

Quick reference

Power

  • Three-phase: V_L = sqrt(3) V_phase for wye, I_L = I_phase for wye, I_L = sqrt(3) I_phase for delta; total real power P = sqrt(3) V_L I_L cos(theta).

  • Per-unit: divide by base values; Z_base = V_base^2 / S_base, I_base = S_base / (sqrt(3) V_base) for three-phase, and per-unit impedance is unchanged when referred across a transformer.

  • Transformer: turns ratio a = N1/N2 = V1/V2; referred impedance scales by a^2, and the equivalent series impedance is found from the short-circuit test while core loss comes from the open-circuit test.

  • Induction motor: synchronous speed n_s = 120 f / p, slip s = (n_s - n_r)/n_s, rotor frequency = s f; developed torque is proportional to air-gap power divided by synchronous speed.

  • Power factor correction: Q_c = P (tan(theta_1) - tan(theta_2)), and the capacitance for a delta bank is C = Q_c / (3 x 2 pi f x V_L^2).

  • Symmetrical components: positive, negative, and zero sequences; zero-sequence currents flow only in grounded-wye paths, and a balanced set has only positive sequence.

  • Transmission line: surge impedance Z_c = sqrt(L/C), and SIL = V_L^2 / Z_c; a short line is modeled by series impedance, a medium line by nominal pi, a long line by distributed parameters.

  • Protection: an overcurrent relay coordinates by time-current curves with the downstream device faster; a distance relay zones roughly 80-85% (Zone 1), 120-150% (Zone 2), and beyond (Zone 3).

  • Generator and motor efficiency: eta = P_out/P_in; losses include copper (I^2R), core, friction and windage, and stray load, and synchronous reactance sets voltage regulation.

FE Electrical & Computer key terms

Thevenin equivalent

A two-terminal linear circuit reduced to one voltage source in series with one resistance, where the source is the open-circuit voltage and the resistance is that seen with sources deactivated. It simplifies load analysis and maximum power transfer calculations.

Related: Norton equivalent, Superposition, Maximum power transfer
Norton equivalent

A two-terminal linear circuit reduced to one current source in parallel with one resistance, where the source is the short-circuit current and the resistance equals the Thevenin resistance. Source conversion links the two forms.

Related: Thevenin equivalent, Superposition
Superposition

A linear-circuit technique that computes the response to each independent source separately with all others deactivated, then sums the individual responses. It applies only to linear quantities such as voltage and current, not power.

Related: Thevenin equivalent, Linearity
Maximum power transfer

The load receives its greatest possible power when its resistance equals the source resistance seen looking back into the network. Efficiency at that point is only 50 percent, so it is not the same as best operating efficiency.

Related: Thevenin equivalent, Impedance matching
Impedance matching

Setting a load impedance equal to the complex conjugate of the source impedance so that reactive parts cancel and maximum power transfers. In RF work, matching networks also transform impedance to control reflections.

Related: Maximum power transfer, Reflection coefficient
Phasor

A complex number representing the amplitude and phase of a sinusoid at a single frequency, letting steady-state AC circuits be solved with algebra. Time derivatives become multiplication by j omega.

Related: Impedance matching, Transfer function
Transfer function

The ratio of a system output phasor to its input phasor as a function of complex frequency s. Its poles and zeros determine stability, transient response, and frequency response magnitude and phase.

Related: Phasor, Bode plot, Pole-zero plot
Bode plot

A pair of straight-line approximations showing a transfer function's magnitude in decibels and phase in degrees versus logarithmic frequency. Corner frequencies from poles and zeros set the slopes of each segment.

Related: Transfer function, Decibel
Decibel

A logarithmic ratio equal to 20 log of a voltage or current ratio, or 10 log of a power ratio. Cascaded stages add in decibels, and 20 dB corresponds to a factor of ten in amplitude.

Related: Bode plot, Gain margin
Root locus

A plot of the closed-loop pole locations as one parameter, usually gain, varies from zero to infinity. Branches start at open-loop poles and end at open-loop zeros.

Related: Pole-zero plot, Routh-Hurwitz criterion, Transfer function
Bode stability margins

Gain margin is the decibel increase in loop gain that drives the loop to unity at the phase crossover; phase margin is the phase shortfall from 180 degrees at the gain crossover. Both indicate relative stability.

Related: Bode plot, Routh-Hurwitz criterion
Routh-Hurwitz criterion

An algebraic test on the coefficients of a characteristic polynomial that counts right-half-plane roots without factoring it. It determines closed-loop stability and the gain range that keeps a system stable.

Related: Root locus, Bode stability margins
Pole-zero plot

A diagram in the complex s-plane marking the roots of the denominator (poles) and numerator (zeros) of a transfer function. Pole positions reveal decay rate, oscillation frequency, and stability.

Related: Root locus, Transfer function
Nyquist sampling theorem

A bandlimited signal can be reconstructed exactly if sampled at more than twice its highest frequency. Sampling below that rate aliases high frequencies onto lower ones, corrupting the recovered signal.

Related: Aliasing, Anti-aliasing filter, Quantization
Aliasing

The folding of frequencies above half the sampling rate onto lower apparent frequencies in the sampled spectrum. It is prevented by filtering the analog input before sampling.

Related: Nyquist sampling theorem, Anti-aliasing filter
Anti-aliasing filter

An analog low-pass filter placed before a sampler to remove components above the Nyquist frequency. Its transition band and order must be chosen so attenuation is adequate at half the sample rate.

Related: Aliasing, Nyquist sampling theorem
Quantization

Mapping continuous sample amplitudes onto a finite set of discrete levels. The resulting error is bounded by half a step and produces a noise floor lowered roughly 6 dB per added bit.

Related: Nyquist sampling theorem, Successive-approximation ADC
Successive-approximation ADC

A converter that determines each output bit in turn by comparing the input against a trial value from a digital-to-analog converter, from most significant to least. It offers moderate speed at low power.

Related: Quantization, Sample-and-hold circuit
Sample-and-hold circuit

A buffer and capacitor that capture an input value and hold it steady while a converter digitizes it. It prevents input changes during conversion from corrupting the result.

Related: Successive-approximation ADC, Quantization
Karnaugh map

A grid arrangement of a truth table in Gray-code order so that adjacent cells differ in one variable. Grouping adjacent ones yields a minimized sum-of-products expression.

Related: Boolean algebra, Don't-care condition
Boolean algebra

The rules for manipulating binary variables using AND, OR, and NOT, including De Morgan's laws and distributivity. It provides the algebraic basis for simplifying and proving logic expressions.

Related: Karnaugh map, Don't-care condition
Don't-care condition

An input combination whose output is irrelevant, usually because that combination never occurs. Such entries may be grouped as ones or zeros to simplify logic.

Related: Karnaugh map, Boolean algebra
Setup and hold time

Setup time is how long data must be stable before a clock edge; hold time is how long after. Violations cause metastable flip-flop outputs and unreliable captured data.

Related: Metastability, Clock skew
Metastability

A condition in which a flip-flop output hovers between logic levels after a timing violation, resolving unpredictably after a delay. Synchronizers reduce its probability of causing failure.

Related: Setup and hold time, Clock skew
Clock skew

The difference in arrival times of the same clock edge at different registers. Positive skew can help or hurt setup and hold margins depending on which path it favors.

Related: Setup and hold time, Metastability
Finite state machine

A sequential logic model with a defined set of states, inputs, outputs, and transition rules. Moore outputs depend only on state; Mealy outputs also depend on current inputs.

Related: Karnaugh map, Setup and hold time
Two's complement

A signed binary representation in which the most significant bit carries negative weight, so negation is bitwise inversion plus one. It makes addition and subtraction share one hardware adder.

Related: Boolean algebra
Cache locality

Temporal locality means recently used data is likely reused soon; spatial locality means nearby addresses are likely accessed. Both justify cache line fetches and replacement policies that improve hit rate.

Related: Pipeline hazard, Virtual memory
Pipeline hazard

A condition that prevents the next instruction from issuing in the following cycle. Structural, data, and control hazards are handled by stalls, forwarding, or branch prediction.

Related: Cache locality, Virtual memory
Virtual memory

An address translation scheme giving each process a private address space mapped to physical frames through page tables. It provides isolation, demand paging, and protection via translation lookaside buffers.

Related: Cache locality, Pipeline hazard
Per-unit system

A normalization in which voltages, currents, and impedances are divided by chosen base values, removing transformer turns ratios from calculations. It makes multi-voltage power networks easier to compare and solve.

Related: Symmetrical components, Power flow study
Symmetrical components

A method decomposing an unbalanced three-phase set into positive, negative, and zero sequences that are analyzed separately. It underpins fault analysis and relay settings.

Related: Per-unit system, Fault analysis
Fault analysis

Computing currents and voltages during short circuits using sequence networks and impedance data. Results size protective devices and set relay coordination.

Related: Symmetrical components, Per-unit system
Power flow study

A numerical solution of network equations giving bus voltages, angles, and line flows for specified generation and load. Buses are classified as slack, PV, or PQ.

Related: Per-unit system, Symmetrical components
Transformer equivalent circuit

A model placing series winding impedance and shunt magnetizing branch on one side after referring the other side through the turns ratio squared. It predicts regulation, losses, and efficiency.

Related: Per-unit system, Power factor
Power factor

The cosine of the angle between voltage and current, equal to real power divided by apparent power. Low values increase current and losses for a given real power delivered.

Related: Transformer equivalent circuit, Per-unit system
Induction motor slip

The difference between synchronous speed and rotor speed, expressed as a fraction of synchronous speed. Slip rises with load and determines rotor frequency and developed torque.

Related: Power factor, Transformer equivalent circuit
Duty cycle

The fraction of a switching period during which a switch conducts. In a buck converter, the output voltage approximately equals input times duty cycle in continuous conduction.

Related: Power factor, Transformer equivalent circuit
Linearity

A property of circuits obeying superposition and scaling of responses. Linear elements include resistors, capacitors, inductors, and ideal sources; diodes and transistors are nonlinear.

Related: Superposition, Thevenin equivalent

FE Electrical & Computer study plan

8 weeks · About 7 hours per week

Week 1

Electrical and Computer: Computer Engineering

  • Refresh number systems and Boolean algebra: convert between binary, octal, hex, and two's complement, and simplify switching expressions with Karnaugh maps and DeMorgan's laws until you can do each without notes.

  • Design combinational building blocks from truth tables: multiplexers, decoders, adders, and comparators, then hand-trace propagation delay through a two-level gate network.

  • Solve 25 practice problems on combinational logic and number representation, logging every error with the underlying concept it exposed.

  • Set up a formula sheet and error log in a spreadsheet that you will append to every week for the rest of the plan.

Your checkpoint

A one-page combinational-logic reference sheet plus a scored 25-problem practice set with an itemized error log.

Week 2

Electrical and Computer: Computer Engineering

  • Analyze sequential circuits: derive next-state and output equations for flip-flop-based machines, build state tables and state diagrams, and identify Mealy versus Moore behavior.

  • Compare SR, JK, D, and T flip-flops on excitation tables and timing, and convert one design from one flip-flop type to another.

  • Work through computer-architecture fundamentals: instruction formats, addressing modes, pipelining hazards, cache mapping (direct, set-associative, fully associative), and hit/miss calculations.

  • Compute cache performance metrics (hit ratio, AMAT) and CPI for given instruction mixes in at least 10 problems.

Your checkpoint

A worked state-machine design (state diagram through next-state equations) plus a 10-problem cache/CPI problem set with correct answers.

Week 3

Electrical and Computer: Computer Engineering & Electrical and Computer: Electrical and Electronics

  • Cover embedded-system and software topics for computer engineering: microcontroller peripherals, interrupts, memory-mapped I/O, and basic data-structure and algorithm complexity (Big-O) questions.

  • Review digital-to-analog and analog-to-digital conversion: sampling theorem, quantization error, resolution, and Nyquist criteria with numeric examples.

  • Begin electronics review by deriving operating points for diode circuits (ideal, constant-drop, and small-signal models) and Zener regulator designs.

  • Solve 20 mixed problems spanning computer engineering and basic electronics to test retention across domains.

Your checkpoint

A 20-problem mixed quiz score of 75% or better, with a written correction for every missed item.

Week 4

Electrical and Computer: Electrical and Electronics

  • Analyze BJT and MOSFET amplifier configurations (common emitter/source, emitter/source follower, common base/gate) for gain, input and output resistance, and phase.

  • Apply small-signal models to compute midband gain and identify the dominant pole qualitatively in a single-stage amplifier.

  • Review op-amp circuits: inverting, non-inverting, summing, difference, integrator, differentiator, and comparator behavior, including slew rate and gain-bandwidth limits.

  • Solve 25 amplifier and op-amp problems under a timed 45-minute block to build speed.

Your checkpoint

A timed 25-problem amplifier/op-amp set completed with a recorded score and time, plus a corrected solutions sheet.

Week 5

Electrical and Computer: Electrical and Electronics

  • Master linear-system analysis: Laplace transforms, transfer functions, pole-zero plots, Bode magnitude and phase sketches, and stability via Routh-Hurwitz.

  • Compute transient and steady-state responses of first- and second-order circuits (RC, RL, RLC) including damping ratio and natural frequency.

  • Review signal and filter fundamentals: Fourier series concepts, ideal filter types, and bandwidth calculations, plus basic communications concepts such as modulation and SNR.

  • Work 15 control-systems and 15 signals/systems problems, then tabulate which subtopics still cost you the most time.

Your checkpoint

A Bode-plot and Routh-Hurwitz worked example set plus a ranked list of your three weakest electrical subtopics.

Week 6

Electrical and Computer: Power

  • Review three-phase power: per-phase equivalent circuits, wye-delta conversion, real/reactive/apparent power, power factor, and balanced-load calculations.

  • Analyze transformers: ideal and non-ideal models, referred impedances, efficiency, and voltage regulation with numeric examples.

  • Cover transmission-line parameters, voltage drop, and power-flow basics, including per-unit calculations on a simple radial feeder.

  • Solve 20 three-phase and transformer problems, verifying each answer with a unit and magnitude sanity check.

Your checkpoint

A 20-problem power set with per-unit conversions shown step by step and a 70% or better score.

Week 7

Electrical and Computer: Power & Electrical and Computer: Electrical and Electronics

  • Study electric machines: DC machine torque and speed relations, induction motor slip and equivalent circuit, and synchronous machine basics, solving at least 10 numeric problems.

  • Review power electronics: rectifiers, DC-DC converters (buck, boost, buck-boost), and inverters, including duty-cycle and ripple calculations.

  • Tie power back to electronics by reviewing protection devices, grounding, and power-factor correction with capacitor banks.

  • Take a 30-question mixed quiz across all three domains and record per-domain accuracy.

Your checkpoint

A per-domain accuracy report from the 30-question mixed quiz, with any domain under 60% flagged for week 8.

Week 8

Electrical and Computer: Computer Engineering & Electrical and Computer: Electrical and Electronics & Electrical and Computer: Power

  • Re-drill every item in your error log from weeks 1 through 7 until each is solved correctly twice in a row without notes.

  • Take two full-length timed practice exams under exam conditions (no pauses, reference sheet only) and score each by domain.

  • Convert exam-day logistics into a checklist: approved calculator, reference handbook familiarity, ID, and time-per-question pacing targets.

  • Review the highest-frequency formulas from each domain for 20 minutes daily to keep them fresh.

Your checkpoint

Two completed timed practice exams with per-domain scores and a final one-page exam-day checklist.

Milestones

Week 2: Can design and analyze a sequential circuit end to end and score 70% or better on a self-made 15-question digital-logic quiz.

Week 4: Computer engineering and electronics subtopics are both at 70% or better on mixed timed sets, and the week-1 error log has been fully reworked once.

Week 6: Power-domain practice score is 70% or better with per-unit conversions done correctly, and the three weakest subtopics from week 5 have been re-drilled.

Week 8: Both full-length practice exams show 60% or better in every domain and an overall score comfortably above the passing threshold you have set as your target.

FE Electrical & Computer exam day

Your checklist

Government-issued photo ID

Bring the original, unexpired ID in the name you registered under. Name mismatches are a common cause of being turned away. Confirm with the provider which specific ID forms are accepted for your test center, since rules differ between in-person and remote-proctored delivery.

Admission or appointment confirmation

Have your scheduling confirmation and any candidate ID number accessible (printed or on your phone before you enter). You may be asked to show it at check-in. Confirm with the provider whether printed copies are required.

Know your test center location and arrival time

Do a route check the day before, note parking or transit options, and plan to arrive earlier than the scheduled start - arriving late can forfeit your seat and fee. Confirm with the provider the exact arrival window and late-arrival cutoff for your appointment.

Approved calculator

The FE exam is administered with a provided or specified calculator model; do not assume your personal graphing calculator is allowed. Confirm with the provider which calculator models are permitted and whether one is supplied at the workstation.

Reference handbook familiarity

The exam supplies an electronic reference handbook inside the testing software. You will not bring your own formula sheets. Practice navigating it beforehand so you can find formulas quickly during the test.

Scratch work materials

Most computer-based testing centers issue an erasable booklet and marker or similar approved materials and prohibit bringing your own paper. Confirm with the provider what is supplied and what is prohibited.

Leave personal items behind or plan storage

Phones, smartwatches, notes, bags, and outerwear are typically not allowed at the workstation and storage may be limited. Plan to travel light and expect to store or surrender items before entering.

Prepare for the scheduled break

There is a scheduled break during the exam. Plan a quick snack and water for the break area if permitted, and know that break time is generally not counted against your testing time. Confirm with the provider the break policy and whether access to your belongings is allowed.

Rest and logistics the night before

Sleep, eat a normal breakfast, and avoid last-minute cramming of new material. Fatigue and anxiety cost more points than one more practice problem.

Practice under timed, screen-based conditions

In the final days, simulate the interface: on-screen reference handbook, on-screen calculator, flagging and reviewing questions, and the break. This reduces interface friction on exam day.

Review your personal error log

Bring a short list of your recurring mistakes (unit conversions, sign conventions, misread qualifiers, time sinks) and read it in the final 24 hours instead of new content.

Confirm scoring and results timeline

Know how and when results are released and how pass/fail is reported. Confirm with the provider the current results timeline rather than relying on secondhand accounts.

Plan the day

Final 72 hours

Shift from learning to consolidation. Take at most one full-length timed practice exam early in this window, then spend the rest of the time reviewing your error log and weak topic areas. Stop introducing new topics. Rehearse the on-screen reference handbook and calculator so navigation is automatic. Verify appointment details, ID, calculator policy, and travel plan. Protect sleep - do not trade sleep for extra study in this window.

Final 24 hours

Do a light review only: your error log, key formula families, unit conventions, and a handful of easy problems to stay sharp. Pack your ID, confirmation, and any permitted items. Confirm the route and arrival time. Eat a normal meal and go to bed at a reasonable hour. Avoid intensive practice exams the night before - they tend to raise anxiety without improving performance.

Morning of the exam

Eat a normal breakfast and hydrate moderately. Arrive early with ID and confirmation in hand. Expect check-in procedures such as ID verification, a photo, and securing personal items. Use the restroom before you are seated. Once at the workstation, take the provided tutorial or interface orientation seriously, and start with a brief calm breath before question one.

During the test

Work in passes. First pass: answer questions you can solve cleanly, flag anything long or uncertain, and move on. Second pass: return to flagged items with remaining time. Watch units and qualifiers (least, most, not, closest to). Use the on-screen reference handbook rather than memory for formulas. If a problem is consuming too much time, guess, flag, and return. Take the scheduled break - use it to stand, hydrate, and reset. Near the end, ensure no question is left blank, since unanswered items cannot earn credit.

Rules to check

  • Bring valid government-issued photo ID matching your registration name; without acceptable ID you may be denied entry and lose your fee. Confirm with the provider the accepted ID forms and name-match requirements.

  • Personal electronic devices, notes, and unauthorized reference materials are prohibited at the workstation. Expect to store or surrender them before testing; possession during the exam can lead to dismissal and score cancellation.

  • Use only the calculator and reference materials permitted by the provider. Do not bring your own formula sheets or rely on a personal calculator unless it is explicitly allowed.

  • Take only the scheduled break. Leaving the testing room outside the break, or accessing prohibited items during the break, may be treated as a testing irregularity. Confirm with the provider the break rules and whether locker access is allowed.

  • Do not communicate with other candidates during the exam and do not attempt to record, photograph, or reproduce exam content. Sharing exam content afterward violates the candidate agreement.

  • Understand the scoring model: results are reported as pass/fail based on the overall exam, not a simple percentage of correct answers, and there is no penalty for guessing. Answer every question.

  • If a technical problem, distraction, or irregularity occurs, notify the proctor immediately and follow their instructions; note the issue so it can be documented.

  • Confirm all logistics - arrival window, late-arrival policy, break policy, permitted items, and results timeline - with the provider before exam day rather than relying on forums or secondhand summaries.

FE Electrical & Computer FAQ

How many FE Electrical & Computer practice questions are available?

The practice set has 200 FE Electrical & Computer questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many FE Electrical & Computer flashcards are available?

The flashcard set has 32 FE Electrical & Computer cards. Each card shows the term and its definition.

Which topics does the FE Electrical & Computer study material cover?

The FE Electrical & Computer study material covers Electrical and Computer: Computer Engineering, Electrical and Computer: Electrical and Electronics, and Electrical and Computer: Power.

What format facts does the catalog list for the FE Electrical & Computer exam?

The catalog lists a duration of 320 minutes and these item types: computer-based and multiple choice (per NCEES FE exam format) for the FE Electrical & Computer exam.