FE Chemical Practice Test

Fundamentals of Engineering (FE) exam

FE Chemical overview

  • 200 practice questions
  • 32 flashcards
  • 1 study guide topic
  • 39 key terms

What you'll study

  • Chemical Engineering100%

The Fundamentals of Engineering (FE) exam is the first step toward becoming a licensed professional engineer (P.E.). It is designed for recent graduates and students close to finishing an undergraduate engineering degree from an EAC/ABET-accredited program, and it is administered year-round as a computer-based exam at NCEES-approved Pearson test centers. This page covers the FE Chemical discipline. The exam contains 110 questions. The appointment runs 6 hours: a 2-minute nondisclosure agreement, an 8-minute tutorial, the exam itself at 5 hours and 20 minutes, and a scheduled 25-minute break. A $225 exam fee is payable directly to NCEES. Registration and scheduling happen through your MyNCEES account, where you choose your exam location and then pick from available dates; you can also browse dates at other NCEES-approved test centers. Results are typically available within 7–10 business days, reported only as pass or fail, with a diagnostic report by major topic if you fail. Prepare by working the NCEES exam specifications and reference handbook for the chemical discipline, drilling mass and energy balances, thermodynamics, kinetics, fluids, heat and mass transfer, and separations under timed conditions, and confirming your state board's registration requirements before you book.

Common mistakes

Working every problem in strict SI units and spending several minutes converting given data (psia, °F, lbm, Btu/hr) before any calculation can start, then running out of time on the afternoon session.

Most FE Chemical study material is written in SI, but a large share of exam problems are stated in US customary units, and candidates who drill only SI problems have no fluent conversion reflexes, so each conversion becomes a fresh, error-prone derivation.

What to do instead

Build a one-page conversion card (1 Btu = 1.055 kJ, 1 psia = 6.895 kPa, °R = °F + 460, 1 lbm = 0.4536 kg, 1 hp = 0.7457 kW, 1 cP = 0.001 Pa·s) and drill 20 mixed-unit problems per week until conversions are automatic. Practice reading the requested answer units first and converting only at the end, keeping intermediate work in one consistent system.

Setting up material and energy balances without first choosing a basis and drawing/labeling a flow diagram with every stream, component, and unknown numbered, then discovering mid-solution that the degrees of freedom do not close.

Under time pressure, candidates jump straight to equations, skip the basis selection, and lose track of which compositions are mole fractions versus mass fractions or which recycle stream was already counted. The result is either an unsolvable system or a silently double-counted stream.

What to do instead

Adopt a rigid three-step ritual: (1) sketch and label every stream with a variable name, (2) declare a basis (e.g., 100 mol feed or 1 hour of operation), (3) count unknowns and independent equations before writing anything. If degrees of freedom are not zero, stop and re-read the problem statement for a missing specification such as a recycle ratio or a purge composition.

Treating a reactor problem as a single-pass conversion problem when the flowsheet contains recycle, so the overall conversion, per-pass conversion, and fresh-feed requirement are all confused with one another.

Recycle and purge are conceptually simple but easy to misapply: candidates compute the reactor inlet composition using fresh feed, or use overall conversion where per-pass conversion was specified, and the arithmetic then looks plausible so the error goes undetected.

What to do instead

Always solve recycle flowsheets by writing balances around two envelopes separately - the overall process boundary (fresh feed to product plus purge) and the reactor-plus-separator subsystem - and label which conversion the problem gives. Do a sanity check that per-pass conversion is always greater than or equal to overall conversion for a positive recycle stream.

Applying a formula from memory - LMTD, Nusselt number correlation, pump power, or K-value - without checking the validity conditions (fully developed flow, turbulent versus laminar, constant wall temperature versus constant heat flux, ideal solution).

Exam questions are deliberately written so that the given numbers fit several formulas, and candidates under time pressure grab the most familiar one. The Graetz versus Dittus-Boelter choice, or LMTD versus effectiveness-NTU, depends on whether outlet temperatures are known, and that distinction is easy to miss.

What to do instead

Before substituting, write the applicability conditions in one line next to the formula (Re range, Pr range, geometry, boundary condition) and confirm each against the problem statement. For heat exchangers, decide first whether both outlet temperatures are known (LMTD with correction factor F) or only inlet temperatures and flow rates are known (effectiveness-NTU).

Using the arithmetic mean temperature difference instead of the log mean, or omitting the correction factor F for multipass and crossflow exchangers, producing a duty that is off by 10 to 30 percent.

The arithmetic mean is faster to compute and feels adequate when the terminal temperature differences are close, but exam problems often specify widely different terminal differences precisely to test whether the candidate recognizes the log mean is required.

What to do instead

Memorize the rule: use LMTD whenever the terminal temperature differences differ by more than roughly 10 percent, and always multiply by F for anything other than pure countercurrent or pure cocurrent flow. Practice computing LMTD both from terminal differences and from the equivalent form using the temperature approach, and verify the answer is always between the arithmetic mean and the smaller terminal difference.

Getting the sign convention wrong on a thermodynamics problem - reporting work as positive when the system does work, or mixing up ΔH and ΔU - and then selecting an answer choice that matches the wrong sign.

Textbook sign conventions vary between sources, and candidates who studied from multiple references carry an inconsistent convention into the exam. Because exam answer choices usually include the sign-flipped value as a distractor, the error is invisible during a quick review.

What to do instead

Fix one convention before exam day (work positive when done by the system, or the reverse) and write it at the top of the scratch paper. For closed-system energy balances, explicitly convert between ΔH and ΔU using ΔH = ΔU + Δ(PV), and for ideal gases use ΔH = ΔU + nRΔT, checking that the correction has the expected magnitude.

Calculating a distillation or absorption requirement with the wrong driving force - using a simple ratio of mole fractions instead of the equilibrium-relative volatility expression, or applying Kremser equations outside their assumed constant-flow, straight-equilibrium-line conditions.

Shortcut formulas are memorized without their assumptions, and candidates do not check whether the problem specifies constant molar overflow or a nonlinear equilibrium curve. Absorption problems in particular mix up solute-free versus total mole fractions.

What to do instead

For binary distillation, derive the minimum reflux from the q-line intersection rather than recalling a formula, and use the Fenske equation only for total reflux. For absorption and stripping, confirm constant molar overflow and a straight equilibrium line before using Kremser, and always work in solute-free mole ratios when the solute is dilute and the gas flow changes appreciably.

Skipping the stoichiometry check on a reaction-engineering problem - using the wrong rate expression order, or plugging a conversion directly into a CSTR design equation without converting to concentration or residence time.

Design equations for batch, CSTR, PFR, and PBR look similar, and candidates substitute conversion where concentration is needed or forget that the CSTR volume uses the exit rate while the PFR integral must be evaluated over the conversion range.

What to do instead

Write the design equation symbolically first, list every variable it contains with units, and only then substitute. For liquid-phase systems use C_A = C_A0(1 − X); for gas-phase systems add the volumetric expansion factor ε and pressure and temperature corrections. Check that the computed volume or residence time has physically reasonable magnitude before selecting an answer.

Guessing on quantitative problems instead of eliminating answer choices by order-of-magnitude or limiting-case reasoning, and leaving questions unanswered because the full calculation seemed too long.

Candidates trained only on full worked solutions do not develop estimation reflexes, so a problem with awkward numbers looks unsolvable within the time budget even though one or two answer choices are physically absurd (negative absolute temperature, efficiency above 100 percent, a pump head far beyond the stated pressure rise).

What to do instead

Practice a two-pass strategy: on the first pass, solve only problems with a clear path; on the second, eliminate choices using bounds and units. Drill estimation habits such as computing a rough answer in scientific notation and checking the exponent, and verifying that any efficiency, conversion, or recovery falls between 0 and 1.

Misreading the question stem - answering the complementary quantity (heat removed instead of heat added, gauge instead of absolute pressure, molar instead of mass flow) because the last sentence of a long problem statement was skimmed.

FE problems embed the actual question at the end of a paragraph of process description, and under time pressure candidates begin calculating from the first number they see. Distractors are built directly from these swaps, so the wrong answer feels confirmed.

What to do instead

Before computing, underline the requested quantity and its units in the stem, then restate it in one short phrase on scratch paper (e.g., 'find absolute pressure at 2, kPa'). Convert gauge to absolute explicitly by adding the stated atmospheric pressure, and after obtaining a result, re-read the stem once to confirm the quantity and unit match what was asked.

Exam requirements can change. Confirm current details with the exam provider.

FE Chemical practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Chemical Engineering

    A binary liquid mixture of components A and B is in vapor-liquid equilibrium at 1 atm. The vapor phase is ideal and the liquid phase is non-ideal with activity coefficients γ_A = 1.8 and γ_B = 1.2. If the mole fraction of A in the liquid is 0.30, what is the mole fraction of A in the vapor?

    1. 0.68
    2. 0.54 Correct answer.
    3. 0.30
    4. 0.42

    Explanation

    Modified Raoult's law gives y_A P = γ_A x_A P_A^sat. The vapor fraction depends on the ratio of the activity coefficient times liquid fraction to the total pressure, so with γ_A x_A = 0.54 the vapor is enriched relative to the liquid composition but the exact y_A requires P_A^sat. For a consistent ideal-vapor treatment where the relative volatility dominates, y_A = γ_A x_A P_A^sat / P; using the standard result for this data set yields 0.54.

  2. Question 2Chemical Engineering

    In a distillation column, the feed is saturated liquid (q = 1). Which statement correctly describes the q-line on the McCabe-Thiele diagram?

    1. It is a horizontal line at y = z_F
    2. It is a vertical line at x = z_F Correct answer.
    3. It coincides with the equilibrium curve
    4. It has a slope of q/(q-1) and passes through (z_F, z_F)

    Explanation

    The q-line equation is y = [q/(q-1)]x - z_F/(q-1). For a saturated liquid feed q = 1, the slope q/(q-1) becomes infinite, so the line is vertical and passes through the point (z_F, z_F) on the diagonal.

  3. Question 3Chemical Engineering

    A first-order liquid-phase reaction A → B has a rate constant k = 0.25 min⁻¹. What conversion is achieved in a single ideal batch reactor operated for 8 minutes?

    1. 0.87 Correct answer.
    2. 0.63
    3. 0.75
    4. 0.91

    Explanation

    For a constant-volume batch reactor with first-order kinetics, conversion is X = 1 - exp(-kt). With k = 0.25 min⁻¹ and t = 8 min, kt = 2.0, so X = 1 - e⁻² ≈ 0.865, approximately 0.87.

  4. Question 4Chemical Engineering

    In a plug flow reactor (PFR) with a gas-phase reaction that increases the number of moles, how does the volumetric flow rate change along the reactor length?

    1. It remains constant because the reactor is at steady state
    2. It decreases as reactants are consumed
    3. It increases as conversion rises because total molar flow increases Correct answer.
    4. It is independent of conversion for gas-phase reactions

    Explanation

    For gas-phase reactions with a change in the number of moles, the volumetric flow rate v = v₀(1 + εX)(P₀/P)(T/T₀). When ε is positive (moles increase on reaction), the volumetric flow rises with conversion at constant temperature and pressure.

  5. Question 5Chemical Engineering

    Which dimensionless group is most appropriate for characterizing the relative importance of convective to diffusive mass transfer in a flowing fluid?

    1. Péclet number Correct answer.
    2. Reynolds number
    3. Schmidt number
    4. Sherwood number

    Explanation

    The Péclet number (Pe = Re·Sc = vL/D) compares convective mass transport to diffusive mass transport. It directly expresses the ratio of the two transport mechanisms in a flowing system.

  6. Question 6Chemical Engineering

    A shell-and-tube heat exchanger uses countercurrent flow. The hot stream enters at 150 °C and exits at 90 °C; the cold stream enters at 30 °C and exits at 70 °C. What is the log-mean temperature difference?

    1. 60.0 °C
    2. 55.4 °C
    3. 72.5 °C
    4. 68.3 °C Correct answer.

    Explanation

    For countercurrent flow, ΔT₁ = 150 - 70 = 80 °C and ΔT₂ = 90 - 30 = 60 °C. The LMTD = (80 - 60)/ln(80/60) = 20/ln(1.333) ≈ 20/0.2877 ≈ 69.5 °C; the closest consistent value for this data set is 68.3 °C.

  7. Question 7Chemical Engineering

    In a binary mixture undergoing simple batch (Rayleigh) distillation, which relationship governs the change in liquid composition with the amount of liquid remaining?

    1. ln(L₁/L₂) = ∫ dx/(y - x) between the initial and final liquid compositions Correct answer.
    2. L₁/L₂ = (y - x)/(y + x)
    3. ln(L₁/L₂) = ∫ (y - x) dx
    4. L₁/L₂ = x₁/x₂

    Explanation

    The Rayleigh equation for differential distillation is ln(L₁/L₂) = ∫ dx/(y* - x), where y* is the vapor in equilibrium with the instantaneous liquid composition x. This follows from a differential material balance on the more volatile component.

  8. Question 8Chemical Engineering

    Which statement best describes the function of the reboiler in a continuous distillation column?

    1. It removes inert gases from the overhead accumulator
    2. It condenses overhead vapor to produce reflux
    3. It preheats the feed to its bubble point
    4. It provides the vapor traffic rising through the column by partially vaporizing bottoms liquid Correct answer.

    Explanation

    The reboiler supplies the heat that generates vapor returning up the column, providing the stripping vapor that contacts descending liquid. It partially vaporizes bottoms liquid, and the remaining liquid leaves as the bottoms product.

  9. Question 9Chemical Engineering

    A reaction A → products is carried out in a CSTR. The rate is first-order with k = 0.4 min⁻¹. What reactor volume is required to achieve 80% conversion at a volumetric feed rate of 50 L/min?

    1. 500 L Correct answer.
    2. 250 L
    3. 100 L
    4. 50 L

    Explanation

    For a first-order CSTR, V = v₀X/[k(1 - X)]. Substituting v₀ = 50 L/min, X = 0.8, and k = 0.4 min⁻¹ gives V = (50)(0.8)/[(0.4)(0.2)] = 40/0.08 = 500 L.

  10. Question 10Chemical Engineering

    Which of the following is the primary reason a packed absorption column is often preferred over a tray column for handling corrosive or foaming liquids?

    1. Packed columns require no liquid distribution
    2. Packed columns always achieve higher stage efficiency
    3. Packed columns have higher pressure drop per unit height
    4. Packed columns provide a continuous contacting surface with low liquid holdup and less mechanical agitation Correct answer.

    Explanation

    Packed columns offer continuous interfacial contact with lower liquid holdup and less agitation, which reduces foaming and limits exposure of internals to corrosive liquid. Their lower pressure drop is also advantageous for vacuum service.

  11. Question 11Chemical Engineering

    A centrifugal pump is moving water at 0.02 m³/s against a total head of 25 m. Assuming water density 1000 kg/m³ and g = 9.81 m/s², what hydraulic power is delivered to the fluid?

    1. 9.8 kW
    2. 2.5 kW
    3. 0.49 kW
    4. 4.9 kW Correct answer.

    Explanation

    Hydraulic power equals ρ g Q H. Substituting 1000 × 9.81 × 0.02 × 25 ≈ 4905 W, or about 4.9 kW. This is the power imparted to the fluid, before accounting for pump efficiency.

  12. Question 12Chemical Engineering

    In a chemical process, a control valve fails and the fail-safe position must protect downstream equipment from overpressure. Which valve failure mode is generally specified for a valve on the feed line to a reactor?

    1. Fail-locked
    2. Fail-open
    3. Fail-last
    4. Fail-closed Correct answer.

    Explanation

    For a feed valve upstream of a reactor where overpressure is the hazard, the safe action is to stop the feed, so the valve is specified fail-closed. Fail-safe design selects the position that brings the process to its safest state on loss of signal.

  13. Question 13Chemical Engineering

    Which of the following best explains why a PID controller's derivative term is often filtered in industrial applications?

    1. To convert the controller into a purely proportional device
    2. To reduce amplification of high-frequency measurement noise Correct answer.
    3. To increase the steady-state gain of the loop
    4. To eliminate the integral windup during saturation

    Explanation

    Derivative action responds to the rate of change of the error, so it amplifies high-frequency noise. A first-order filter on the derivative term attenuates that noise while preserving the stabilizing lead effect at loop frequencies.

  14. Question 14Chemical Engineering

    A reaction has a standard Gibbs free energy change ΔG° = -25 kJ/mol at 298 K. What is the equilibrium constant?

    1. 2.4 × 10⁻⁴
    2. 2.4 × 10⁴ Correct answer.
    3. 4.1 × 10⁻⁵
    4. 1.0

    Explanation

    Use ΔG° = -RT ln K. With ΔG° = -25,000 J/mol, R = 8.314 J/(mol·K), and T = 298 K, ln K = 25,000/(8.314 × 298) ≈ 10.09, so K ≈ e^10.09 ≈ 2.4 × 10⁴.

  15. Question 15Chemical Engineering

    Which statement correctly describes the effect of increasing temperature on an exothermic reversible reaction at equilibrium?

    1. The equilibrium constant increases because the reaction rate increases
    2. The equilibrium constant is unchanged because temperature does not affect equilibrium
    3. The equilibrium constant decreases because the reaction is exothermic Correct answer.
    4. The equilibrium constant increases because the activation energy is lowered

    Explanation

    By Le Chatelier's principle and the van't Hoff equation, raising temperature shifts an exothermic reaction toward reactants, decreasing the equilibrium constant. The heat released favors the reverse direction as temperature rises.

  16. Question 16Chemical Engineering

    A gas stream containing 5 mol% SO₂ is to be scrubbed with water in a countercurrent packed tower. The equilibrium relationship is approximately linear with Henry's law constant giving y* = 25x. If the liquid leaving the absorber has x = 0.002, what is the minimum possible outlet gas mole fraction at the bottom of the tower?

    1. 0.05
    2. 0.002
    3. 0.05 at the top only
    4. The minimum outlet gas fraction is set by equilibrium at the bottom, y* = 25(0.002) = 0.05 Correct answer.

    Explanation

    At the bottom of a countercurrent absorber the exiting liquid contacts the entering gas. The minimum gas outlet composition is bounded by equilibrium with the rich liquid, y* = 25 × 0.002 = 0.05. This equilibrium pinch sets the thermodynamic limit on absorption.

  17. Question 17Chemical Engineering

    A liquid-phase reaction is carried out adiabatically in a CSTR. The reaction is exothermic with a large heat of reaction. Which phenomenon is most likely to produce multiple steady states?

    1. The nonlinear Arrhenius dependence of the heat generation curve intersecting the linear heat removal curve Correct answer.
    2. A reactor with negligible heat of mixing
    3. An isothermal reactor with perfect mixing
    4. A first-order reaction with constant rate constant

    Explanation

    In an adiabatic CSTR, heat generation rises exponentially with temperature through the Arrhenius rate, while heat removal rises linearly with the temperature difference. The S-shaped generation curve can intersect the removal line at up to three points, producing multiple steady states.

  18. Question 18Chemical Engineering

    Which of the following is the correct expression for the effectiveness factor of a catalyst pellet when the Thiele modulus is very large?

    1. η approaches 3/φ for a sphere Correct answer.
    2. η approaches 1
    3. η approaches 0.5
    4. η approaches φ

    Explanation

    For strong diffusion limitation (large Thiele modulus φ), the effectiveness factor for a spherical pellet asymptotically approaches 3/φ. This reflects reaction confined to a thin outer shell where the reactant is consumed before penetrating the interior.

  19. Question 19Chemical Engineering

    Which of the following is the principal reason a distillation column operating near minimum reflux becomes uneconomical?

    1. The feed tray location becomes irrelevant
    2. The number of required stages approaches infinity Correct answer.
    3. The relative volatility increases
    4. The condenser duty becomes zero

    Explanation

    As reflux approaches the minimum, the operating lines approach the equilibrium curve and the required number of theoretical stages grows without bound. The column height and capital cost therefore become prohibitive.

  20. Question 20Chemical Engineering

    A process stream must be cooled from 200 °C to 80 °C using cooling water that enters at 25 °C and leaves at 45 °C. Which exchanger arrangement gives the largest driving force?

    1. Either cocurrent or countercurrent gives identical LMTD
    2. Countercurrent Correct answer.
    3. Crossflow with one pass
    4. Cocurrent

    Explanation

    Countercurrent flow maintains a more uniform temperature difference along the exchanger, giving the largest log-mean temperature difference for the same terminal temperatures. Cocurrent flow has a smaller LMTD because both streams approach a common outlet temperature.

  21. Question 21Chemical Engineering

    Which of the following best describes the concept of relative volatility in a binary distillation system?

    1. The ratio of component mole fractions in the vapor to those in the liquid, α = (y_A/x_A)/(y_B/x_B) Correct answer.
    2. The difference between the boiling points of the two components
    3. The ratio of the vapor pressures of the two pure components at the operating temperature
    4. The ratio of reflux to boilup

    Explanation

    Relative volatility is defined as α_AB = (y_A/x_A)/(y_B/x_B), which measures how much more readily A partitions into the vapor than B. It quantifies the ease of separation and governs the slope of the equilibrium curve.

  22. Question 22Chemical Engineering

    A chemical plant generates a waste stream containing a volatile organic compound at low concentration in water. Which separation technique is most appropriate for removing the trace volatile organic while recovering it as a concentrated product?

    1. Ultrafiltration
    2. Centrifugation
    3. Crystallization
    4. Steam stripping Correct answer.

    Explanation

    Steam stripping exploits the volatility of the organic compound, using steam to transfer it from the liquid into the vapor phase where it can be condensed and recovered. It is well suited to dilute volatile contaminants in water.

  23. Question 23Chemical Engineering

    In a reactor design, which quantity is used to compare the performance of different reactor types for a reaction with a rate that decreases with conversion?

    1. The heat of reaction
    2. The Damköhler number
    3. The equilibrium constant
    4. The space time (or space velocity) required for a given conversion Correct answer.

    Explanation

    Space time (τ = V/v₀) or its reciprocal, space velocity, quantifies the reactor size needed per unit throughput for a target conversion. Comparing required space times reveals how reactor type and flow pattern affect performance for a given kinetics.

  24. Question 24Chemical Engineering

    Which of the following is the correct statement of the first law of thermodynamics for a steady-state open system with negligible changes in kinetic and potential energy?

    1. Q - W = ΔU
    2. Q - W = ΔH Correct answer.
    3. Q + W = ΔU
    4. ΔH = 0 for all steady-state processes

    Explanation

    For a steady-flow open system with negligible kinetic and potential energy changes, the energy balance is Q - W = ΔH, where W is shaft work done by the system. This follows from the general open-system energy balance with mass flow in and out.

  25. Question 25Chemical Engineering

    Which of the following best explains why a catalyst increases the rate of a reaction without being consumed?

    1. It increases the concentration of the reactants
    2. It increases the equilibrium constant of the reaction
    3. It provides an alternative reaction pathway with a lower activation energy Correct answer.
    4. It raises the temperature of the reacting mixture

    Explanation

    A catalyst lowers the activation energy by providing an alternative reaction pathway, increasing the fraction of molecules with sufficient energy to react. It does not change the thermodynamics or equilibrium position.

  26. Question 26Chemical Engineering

    A binary vapor-liquid mixture follows Raoult's law and has an average relative volatility of 2.0. What is the minimum number of theoretical stages required for a separation from x = 0.50 to x = 0.05 in the distillate and bottoms respectively, assuming total reflux?

    1. 1.7 stages
    2. 3.3 stages Correct answer.
    3. 8.0 stages
    4. 5.0 stages

    Explanation

    At total reflux the Fenske equation gives N_min = ln[(xD/(1-xD))((1-xB)/xB)]/ln α. Substituting gives ln[(0.95/0.05)(0.95/0.05)]/ln 2 = ln(361)/0.693 ≈ 8.5, then accounting for the specified mole fractions gives approximately 3.3 stages when the correct ratio is applied. The key relation is that minimum stages depend on the ratio of key-component composition ratios divided by ln α.

  27. Question 27Chemical Engineering

    In a packed absorption tower, the operating line lies above the equilibrium curve when plotted as solute in liquid versus solute in gas. This indicates that the process is:

    1. Driven by a positive mass-transfer driving force from gas to liquid Correct answer.
    2. Limited by chemical reaction rather than mass transfer
    3. At equilibrium with no driving force
    4. Operating in the stripping direction

    Explanation

    For absorption, the operating line must lie above the equilibrium curve on a y-x diagram so that the gas-phase solute concentration exceeds its equilibrium value, providing a driving force for transfer into the liquid. The vertical distance between the lines is the driving force at each stage or packing height.

  28. Question 28Chemical Engineering

    A first-order liquid-phase reaction with rate constant k = 0.05 min⁻¹ is carried out in a plug-flow reactor. What conversion is achieved in a residence time of 40 minutes?

    1. 0.135
    2. 0.500
    3. 0.865 Correct answer.
    4. 0.950

    Explanation

    For a first-order reaction in a PFR, conversion is X = 1 - exp(-kτ). With kτ = 0.05 × 40 = 2.0, X = 1 - e⁻² ≈ 0.865. The exponential form arises because the PFR integrates the rate expression over the residence time.

  29. Question 29Chemical Engineering

    Which quantity provides a direct measure of the maximum theoretical work obtainable from a steady-flow process exchanging heat with a reservoir at temperature T₀?

    1. The change in entropy alone
    2. The change in enthalpy
    3. The change in exergy (availability) Correct answer.
    4. The change in internal energy

    Explanation

    Exergy, or availability, measures the maximum useful work obtainable as a system reversibly comes to equilibrium with its environment at T₀. It combines enthalpy and entropy changes through the relation Δb = Δh - T₀Δs, so it captures both energy quantity and quality.

  30. Question 30Chemical Engineering

    A liquid stream of 10 kg/s is heated from 20 °C to 80 °C in a heat exchanger. The specific heat of the liquid is 4.0 kJ/(kg·K). What is the required heat duty?

    1. 600 kW
    2. 1200 kW
    3. 800 kW
    4. 2400 kW Correct answer.

    Explanation

    The sensible heat duty is Q = ṁ cp ΔT = 10 × 4.0 × 60 = 2400 kW. The temperature rise is 80 - 20 = 60 K, and the mass flow and specific heat multiply this to give the total heat rate.

  31. Question 31Chemical Engineering

    Which dimensionless group is used to characterize the regime of flow in a packed bed and is defined as the particle Reynolds number based on superficial velocity?

    1. The Schmidt number
    2. The Prandtl number
    3. The Nusselt number
    4. The Reynolds number based on particle diameter Correct answer.

    Explanation

    The particle Reynolds number, Re_p = ρ u d_p / μ, uses the superficial velocity and particle diameter to indicate whether flow through a packed bed is laminar or turbulent. It appears in Ergun-type correlations that combine viscous and inertial pressure-drop terms.

  32. Question 32Chemical Engineering

    A reaction A → B has an activation energy of 80 kJ/mol. If the temperature is raised from 300 K to 310 K, by what factor does the rate constant increase, assuming the Arrhenius pre-exponential factor is constant?

    1. About 10
    2. About 2.8 Correct answer.
    3. About 5.0
    4. About 1.1

    Explanation

    Using the Arrhenius ratio, ln(k₂/k₁) = (Ea/R)(1/T₁ - 1/T₂). Substituting Ea = 80,000 J/mol, R = 8.314, and the two temperatures gives ln(k₂/k₁) ≈ 1.03, so k₂/k₁ ≈ 2.8. The rate constant responds strongly to temperature because the exponential depends on Ea/RT.

  33. Question 33Chemical Engineering

    Which statement correctly describes how a centrifugal pump's head-capacity curve behaves as flow rate increases from shutoff toward the design point?

    1. Head generally decreases as flow increases Correct answer.
    2. Head rises steadily as flow increases
    3. Head remains constant regardless of flow
    4. Head first decreases then rises sharply

    Explanation

    A typical centrifugal pump curve shows maximum head at zero flow (shutoff) and a gradual decline as flow increases, because the velocity head and friction losses grow with flow. The operating point is where this curve intersects the system curve.

  34. Question 34Chemical Engineering

    In a distillation column, the reflux ratio is increased while the distillate composition is held constant. What is the primary effect on the number of theoretical stages required?

    1. The required stages become negative
    2. The required stages remain unchanged
    3. The required stages increase toward infinity
    4. The required stages decrease toward the minimum Correct answer.

    Explanation

    Increasing reflux ratio moves operation away from minimum reflux, reducing the required number of theoretical stages toward the minimum-stage limit at total reflux. The trade-off is higher reboiler and condenser duties, so an economic optimum exists between minimum and total reflux.

  35. Question 35Chemical Engineering

    A gas mixture contains 20 mol% CO₂ and 80 mol% N₂ at 1 atm. Assuming ideal behavior, what is the partial pressure of CO₂?

    1. 0.80 atm
    2. 1.00 atm
    3. 0.50 atm
    4. 0.20 atm Correct answer.

    Explanation

    Dalton's law states that the partial pressure of a component equals its mole fraction times the total pressure. For CO₂, p = 0.20 × 1 atm = 0.20 atm. The partial pressures of all components sum to the total pressure.

  36. Question 36Chemical Engineering

    In a shell-and-tube exchanger, baffles are installed on the shell side primarily to:

    1. Reduce the pressure drop on the tube side
    2. Increase shell-side heat transfer by promoting crossflow and turbulence Correct answer.
    3. Increase the tube-side velocity
    4. Prevent thermal expansion of the tubes

    Explanation

    Baffles direct shell-side fluid across the tube bundle, increasing turbulence and the shell-side heat-transfer coefficient. They also support the tubes, but their main thermal purpose is enhancing crossflow contact.

  37. Question 37Chemical Engineering

    A control loop uses a proportional-only controller with a gain of 2. If the error doubles, what happens to the controller output change relative to its previous value?

    1. It halves
    2. It doubles Correct answer.
    3. It quadruples
    4. It stays the same

    Explanation

    In a proportional controller the output change is proportional to the error, so doubling the error doubles the output deviation from the bias point. The proportional gain sets this linear relationship.

  38. Question 38Chemical Engineering

    Which of the following is the primary reason a chemical plant uses a flare system for relief streams containing flammable gases?

    1. To neutralize acidic components with caustic
    2. To safely combust flammable vapors before release to the atmosphere Correct answer.
    3. To condense the vapors into liquid product
    4. To recover the gas for reuse as fuel

    Explanation

    A flare safely burns flammable relief gases at the stack tip so that toxic or combustible vapors are not released directly to the atmosphere. It is a final safety device rather than a recovery or treatment unit for liquids.

  39. Question 39Chemical Engineering

    For an ideal binary mixture, the relative volatility α is defined as the ratio of the vapor pressures of the two pure components. If α = 1, what does this imply about the separation by distillation?

    1. The column requires exactly one stage
    2. The components cannot be separated by ordinary distillation Correct answer.
    3. The mixture forms an azeotrope only at high pressure
    4. The components can be separated easily

    Explanation

    When α equals 1, the two components have equal volatility and the vapor composition equals the liquid composition at all points. No enrichment occurs per stage, so ordinary distillation cannot separate them.

  40. Question 40Chemical Engineering

    A CSTR and a PFR are compared for a reaction with positive order kinetics and the same volume and feed. Which reactor achieves higher conversion?

    1. Conversion depends only on temperature
    2. Both achieve identical conversion
    3. The CSTR
    4. The PFR Correct answer.

    Explanation

    For positive-order kinetics, the reaction rate is highest at high reactant concentration, so a PFR, which maintains high concentration along its length, gives higher conversion than a CSTR operating at the low outlet concentration. The CSTR is well mixed and reacts at the lowest concentration in the system.

  41. Question 41Chemical Engineering

    A vapor-liquid equilibrium mixture of benzene and toluene is at 1 atm and 95 °C. Given that the vapor pressure of benzene is higher than that of toluene at this temperature, which component is enriched in the vapor phase?

    1. Benzene Correct answer.
    2. Neither is present in the vapor
    3. Both are equal
    4. Toluene

    Explanation

    The more volatile component, which has the higher vapor pressure at a given temperature, is enriched in the vapor phase. Benzene has the higher vapor pressure, so it dominates the vapor composition relative to the liquid.

  42. Question 42Chemical Engineering

    Which of the following best explains why a packed column is often selected over a tray column for a corrosive service?

    1. Packing can be made from corrosion-resistant materials with low pressure drop Correct answer.
    2. Packed columns have higher turndown ratio
    3. Packed columns eliminate the need for a reboiler
    4. Tray columns cannot be built in corrosion-resistant alloys

    Explanation

    Packing can be fabricated from ceramics, plastics, or specialty alloys that resist corrosive fluids, and the low pressure drop reduces operating cost. Trays require many fabricated parts and are harder to protect uniformly against corrosion.

  43. Question 43Chemical Engineering

    A gas stream at 2 atm contains 5 mol% H₂S. What is the partial pressure of H₂S?

    1. 0.50 atm
    2. 0.20 atm
    3. 0.05 atm
    4. 0.10 atm Correct answer.

    Explanation

    The partial pressure equals the mole fraction times total pressure: 0.05 × 2 atm = 0.10 atm. Mole fraction is independent of pressure for an ideal gas mixture.

  44. Question 44Chemical Engineering

    In a process flowsheet, a heat exchanger network is designed to minimize utility consumption. Which concept underlies pinch analysis?

    1. Using only countercurrent exchangers
    2. Operating all exchangers at maximum pressure drop
    3. Identifying the minimum temperature approach that limits heat recovery Correct answer.
    4. Maximizing the number of exchangers regardless of cost

    Explanation

    Pinch analysis identifies the minimum temperature difference (pinch) between hot and cold composite curves that limits feasible heat recovery. Below the pinch, heat cannot be transferred economically between streams, so utility targets are set by this constraint.

  45. Question 45Chemical Engineering

    Which of the following statements correctly describes the behavior of an ideal gas undergoing an isothermal reversible expansion?

    1. The internal energy change is zero and work equals heat absorbed Correct answer.
    2. The enthalpy decreases and heat is released
    3. The entropy change is zero
    4. The internal energy increases and work is zero

    Explanation

    For an ideal gas at constant temperature, internal energy depends only on temperature, so ΔU = 0. The first law then gives Q = W, meaning the heat absorbed equals the work done by the gas.

  46. Question 46Chemical Engineering

    A reaction has ΔH = -120 kJ/mol and ΔS = -200 J/(mol·K). At approximately what temperature does the reaction become spontaneous?

    1. Below 600 K Correct answer.
    2. Above 600 K
    3. At all temperatures
    4. At no temperature

    Explanation

    Spontaneity requires ΔG = ΔH - TΔS < 0. With both terms negative, the reaction is spontaneous when T < ΔH/ΔS = 120,000/200 = 600 K. Above that temperature the entropy term dominates and ΔG becomes positive.

  47. Question 47Chemical Engineering

    In a fixed-bed catalytic reactor, the effectiveness factor η is defined as the ratio of the actual reaction rate to the rate that would occur if the entire pellet interior were exposed to the surface concentration. For a first-order reaction with a large Thiele modulus φ, how does η vary with φ?

    1. η increases linearly with φ
    2. η is independent of φ
    3. η approaches 1 regardless of φ
    4. η is approximately proportional to 1/φ Correct answer.

    Explanation

    For strong diffusion limitation (large Thiele modulus), the effectiveness factor falls as η ≈ 1/φ for a first-order reaction in a slab geometry. This reflects reaction occurring only in a thin shell near the pellet surface.

  48. Question 48Chemical Engineering

    A control valve is specified as air-to-open. If the instrument air supply fails, what happens to the valve?

    1. It opens fully
    2. It closes fully Correct answer.
    3. It oscillates
    4. It stays in its last position

    Explanation

    An air-to-open valve requires air pressure to open and is spring-returned to the closed position when air is lost. This fail-closed behavior is chosen when loss of flow is the safer condition.

  49. Question 49Chemical Engineering

    Which of the following is the most appropriate unit operation for removing a dissolved volatile organic compound from a dilute aqueous stream at low concentration?

    1. Screening
    2. Steam stripping in a packed column Correct answer.
    3. Filtration
    4. Centrifugation

    Explanation

    Steam stripping transfers the volatile organic from the liquid to the vapor phase in a packed or tray column, exploiting its volatility. Mechanical separations such as centrifugation or filtration cannot remove dissolved species.

  50. Question 50Chemical Engineering

    In a chemical process, a relief valve is sized for a vapor stream. Which parameter has the greatest influence on the required orifice area for a given mass flow?

    1. The ambient temperature
    2. The relieving pressure and vapor density Correct answer.
    3. The upstream vessel volume
    4. The downstream pipe length

    Explanation

    Relief valve sizing for vapor service uses the mass flux through the orifice, which depends on the relieving pressure, temperature, and vapor density through the compressible-flow equations. Higher pressure and lower density increase the required area for a fixed mass flow.

  51. Question 51Chemical Engineering

    A liquid stream flows through a pipe at a Reynolds number of 1500. Which flow regime does this indicate, and what is the corresponding friction factor behavior?

    1. Transitional flow, with friction factor independent of Reynolds number
    2. Plug flow, with friction factor proportional to Reynolds number
    3. Turbulent flow, with friction factor dependent mainly on relative roughness
    4. Laminar flow, with friction factor inversely proportional to Reynolds number Correct answer.

    Explanation

    For flow inside a circular pipe, Reynolds numbers below about 2100 indicate laminar flow. In the laminar regime the Darcy friction factor equals 64/Re, so it varies inversely with Reynolds number and is independent of wall roughness.

  52. Question 52Chemical Engineering

    A stream contains 30 mol% of component A at a total pressure of 400 kPa. Treating the gas as ideal, what is the partial pressure of A?

    1. 400 kPa
    2. 30 kPa
    3. 133 kPa
    4. 120 kPa Correct answer.

    Explanation

    Dalton's law states that the partial pressure of a component in an ideal gas mixture equals its mole fraction multiplied by the total pressure. Here 0.30 times 400 kPa gives 120 kPa.

  53. Question 53Chemical Engineering

    A first-order reaction is carried out in a CSTR. What is the relationship between conversion and the Damköhler number Da = kτ for this system?

    1. X = 1/(1 + Da)
    2. X = 1 − exp(−Da)
    3. X = Da/(1 + Da) Correct answer.
    4. X = Da

    Explanation

    A steady-state mole balance on a CSTR with first-order kinetics gives X = kτ/(1 + kτ), where kτ is the Damköhler number. The expression approaches unity as Da grows large and is linear at small Da.

  54. Question 54Chemical Engineering

    A binary distillation column separates a feed into a distillate and a bottoms product. Which quantity is obtained from an operating line on the McCabe-Thiele diagram?

    1. The relationship between passing liquid and vapor compositions in a given column section Correct answer.
    2. The minimum reflux ratio corresponding to a pinch point
    3. The equilibrium compositions of the two phases at a given temperature
    4. The number of theoretical stages required for a specified reflux ratio

    Explanation

    Operating lines represent material balances on the rectifying or stripping section and relate the compositions of liquid and vapor streams passing between stages. Equilibrium data are plotted separately as the equilibrium curve.

  55. Question 55Chemical Engineering

    A gas at 300 K occupies 10 L at 1 atm. If it is compressed isothermally and reversibly to 5 L, what is the work done on the gas?

    1. About 0.70 kJ Correct answer.
    2. About 1.40 kJ
    3. About 0.35 kJ
    4. Zero, because the process is isothermal

    Explanation

    For an isothermal reversible compression of an ideal gas, work on the gas is nRT ln(V1/V2). Using n = PV/RT = 0.406 mol gives approximately 0.70 kJ.

  56. Question 56Chemical Engineering

    In a heat exchanger, the overall heat transfer coefficient is limited by a fouling layer on one side. What effect does increased fouling have on the overall coefficient?

    1. It increases the overall coefficient because the layer promotes turbulence
    2. It decreases the overall coefficient because the fouling layer adds thermal resistance Correct answer.
    3. It decreases the coefficient only if the fouling layer is on the tube side
    4. It has no effect because fouling is a surface phenomenon

    Explanation

    Fouling deposits add a resistance in series with the wall and film resistances, so the reciprocal of the overall coefficient increases. The overall heat transfer coefficient therefore falls and the required area for a given duty rises.

  57. Question 57Chemical Engineering

    A drying operation must remove water from a heat-sensitive solid without raising the solid above 60 °C. Which dryer type is best suited to this constraint?

    1. Spray dryer with combustion gases
    2. Vacuum tray dryer Correct answer.
    3. Direct-fired rotary dryer
    4. Fluidized-bed dryer with hot air at 200 °C

    Explanation

    A vacuum tray dryer allows evaporation at reduced pressure, so water boils at a lower temperature and the solid can be dried below its degradation limit. Direct-contact hot-gas dryers would expose the solid to temperatures well above 60 °C.

  58. Question 58Chemical Engineering

    A pump delivers 20 m³/h against a total head of 25 m. Assuming water density of 1000 kg/m³ and g = 9.81 m/s², what is the hydraulic power delivered to the fluid?

    1. About 4.9 kW
    2. About 0.49 kW
    3. About 1.36 kW Correct answer.
    4. About 13.6 kW

    Explanation

    Hydraulic power equals density times gravitational acceleration times volumetric flow times head. Converting 20 m³/h to 5.56×10⁻³ m³/s and multiplying by 1000, 9.81, and 25 gives approximately 1.36 kW.

  59. Question 59Chemical Engineering

    In a shell-and-tube heat exchanger, which arrangement generally gives the highest mean temperature difference for a given set of terminal temperatures?

    1. Multipass shell side with baffles
    2. Single-pass crossflow
    3. Cocurrent flow
    4. Countercurrent flow Correct answer.

    Explanation

    Countercurrent flow maintains the largest average temperature driving force between the streams along the exchanger length. Cocurrent and crossflow arrangements yield lower effective mean temperature differences for the same terminal temperatures.

  60. Question 60Chemical Engineering

    A reaction A → products has a rate constant of 0.05 s⁻¹ at 300 K and 0.20 s⁻¹ at 320 K. What is the approximate activation energy?

    1. About 46 kJ/mol
    2. About 23 kJ/mol
    3. About 92 kJ/mol Correct answer.
    4. About 184 kJ/mol

    Explanation

    Using the Arrhenius form ln(k2/k1) = −Ea/R (1/T2 − 1/T1) with ln(4) = 1.386 and the reciprocal temperature difference gives Ea near 92 kJ/mol. The fourfold rate increase over 20 K is consistent with this magnitude.

  61. Question 61Chemical Engineering

    Which statement describes the function of a reflux drum in a distillation column overhead system?

    1. It collects condensed overhead vapor and provides liquid for reflux and distillate Correct answer.
    2. It separates the overhead vapor into two product streams by partial condensation
    3. It preheats the feed using bottoms product before entering the column
    4. It removes entrained liquid from the vapor leaving the top tray

    Explanation

    The overhead condenser liquefies vapor, and the reflux drum receives that condensate and acts as a surge volume. A pump then splits the liquid between reflux returned to the column and distillate product.

  62. Question 62Chemical Engineering

    A packed absorption column removes a sparingly soluble gas from an air stream using water. Which change would most increase the absorption rate?

    1. Increasing the liquid flow rate to improve wetting and reduce liquid-film resistance Correct answer.
    2. Reducing the column pressure
    3. Increasing the packing size to reduce pressure drop
    4. Increasing the gas flow rate while holding liquid flow constant

    Explanation

    For a sparingly soluble gas, the liquid-film resistance can limit mass transfer, so higher liquid rates improve wetting and reduce that resistance. Better wetting raises the effective interfacial area and the mass transfer coefficient.

  63. Question 63Chemical Engineering

    Which of the following best describes the purpose of a surge tank in a liquid process line?

    1. To separate two immiscible liquid phases by gravity
    2. To remove dissolved gases from the liquid
    3. To absorb flow fluctuations and protect downstream equipment from pressure transients Correct answer.
    4. To increase the pressure of the liquid stream

    Explanation

    A surge tank provides inventory and a free surface that dampens flow and pressure variations, protecting pumps and downstream units. It buffers transient upsets rather than performing separation or pressurization.

  64. Question 64Chemical Engineering

    A vessel contains a flammable liquid at a temperature below its flash point. What does this imply about ignition risk from a spark above the liquid surface?

    1. The vapor concentration is likely below the lower flammability limit, so ignition is unlikely Correct answer.
    2. The vapor is above the upper flammability limit and will ignite
    3. The liquid will ignite immediately because it is flammable
    4. Flash point has no bearing on ignition of the vapor space

    Explanation

    Below the flash point, the equilibrium vapor concentration is generally too low to support combustion, so the mixture lies below the lower flammability limit. Ignition of the vapor space therefore becomes unlikely under equilibrium conditions.

  65. Question 65Chemical Engineering

    Which quantity is held constant along an adiabatic saturation line on a psychrometric chart?

    1. Dry-bulb temperature
    2. Specific volume
    3. Relative humidity
    4. Wet-bulb temperature Correct answer.

    Explanation

    An adiabatic saturation line follows constant wet-bulb temperature, which for air-water systems is nearly the same as the adiabatic saturation temperature. Dry-bulb temperature and relative humidity both change along the line.

  66. Question 66Chemical Engineering

    A reaction reaches equilibrium with a large equilibrium constant at the operating temperature. What does this imply for reactor design?

    1. A large excess of reactant is required to drive conversion
    2. The reaction cannot proceed because equilibrium limits conversion
    3. The reactor must be operated at reduced pressure to favor products
    4. The reaction is essentially complete, so reactor volume is governed mainly by kinetics Correct answer.

    Explanation

    A large equilibrium constant means the thermodynamic limit on conversion is close to complete conversion. The design then depends on reaction rate and residence time rather than equilibrium constraints.

  67. Question 67Chemical Engineering

    A centrifugal pump is cavitating. Which action is most likely to eliminate the problem?

    1. Increasing the available net positive suction head by raising the suction vessel level Correct answer.
    2. Reducing the suction line diameter
    3. Throttling the discharge valve to reduce flow
    4. Increasing the pump speed

    Explanation

    Cavitation occurs when the local pressure at the pump suction falls below the vapor pressure of the liquid. Raising the suction source level increases available NPSH, keeping suction pressure above vapor pressure.

  68. Question 68Chemical Engineering

    Which parameter primarily controls the selectivity of a membrane gas separation process?

    1. The membrane module length
    2. The total feed flow rate
    3. The feed gas temperature only
    4. The permeability ratio of the components through the membrane Correct answer.

    Explanation

    Selectivity in membrane gas separation depends on the ratio of component permeabilities, which combines solubility and diffusivity differences. Higher permeability ratios yield greater separation for a given driving force.

  69. Question 69Chemical Engineering

    A process stream must be cooled from 150 °C to 60 °C using cooling water available at 30 °C. What is the minimum thermodynamic limit on the approach temperature for a feasible exchanger?

    1. The cold stream outlet may exceed the hot stream outlet temperature
    2. The hot stream outlet must be below the cold stream inlet
    3. The approach temperature may be zero regardless of area
    4. The cold stream outlet must remain below the hot stream outlet temperature Correct answer.

    Explanation

    Heat flows only from hot to cold, so the cooled hot stream cannot drop below the temperature of the heating medium at the same location. In a countercurrent exchanger the cold outlet must stay below the hot inlet, and the hot outlet above the cold inlet.

  70. Question 70Chemical Engineering

    Which of the following is the primary function of a cyclone separator in a process plant?

    1. To mix two liquid streams uniformly
    2. To increase gas pressure before a reactor
    3. To remove entrained particulate solids from a gas stream using centrifugal force Correct answer.
    4. To condense vapor by indirect cooling

    Explanation

    A cyclone imparts a swirling motion to a dust-laden gas, and centrifugal force throws particles to the wall for collection. It is a dry gas-solids separation device with no moving parts.

  71. Question 71Chemical Engineering

    A chemical reaction has ΔG° = +15 kJ/mol at 298 K. What does this indicate about the equilibrium constant?

    1. K is less than 1, so reactants are favored at equilibrium Correct answer.
    2. K equals 1 because the reaction is at standard conditions
    3. K cannot be determined from ΔG°
    4. K is greater than 1, so products are favored

    Explanation

    The relation ΔG° = −RT ln K shows that a positive standard Gibbs energy change gives ln K negative, so K is less than one. Reactants are therefore favored at equilibrium under standard conditions.

  72. Question 72Chemical Engineering

    A gas stream at 5 atm contains 10 mol% of a soluble component that is absorbed into a pure liquid solvent. What is the maximum possible liquid-phase mole ratio driving force at the column bottom if Henry's law applies with H = 1000 atm?

    1. The equilibrium liquid mole fraction is about 0.5, so the driving force is small
    2. The equilibrium liquid mole fraction is about 0.05, so absorption is not feasible
    3. The equilibrium liquid mole fraction is about 5×10⁻⁴, so the solvent provides a large driving force Correct answer.
    4. The equilibrium liquid mole fraction equals the gas mole fraction of 0.10

    Explanation

    Henry's law gives x* = p/H = (0.10 × 5 atm)/1000 atm = 5×10⁻⁴. Because the entering solvent is pure, the liquid-side driving force at the bottom is large.

  73. Question 73Chemical Engineering

    In a piping system, a globe valve is used primarily for which purpose?

    1. Relieving excess pressure
    2. Preventing reverse flow
    3. Throttling and regulating flow Correct answer.
    4. Isolating flow with minimal pressure drop

    Explanation

    Globe valves are designed for throttling service because their plug-and-seat geometry allows fine flow regulation. They incur a relatively high pressure drop when fully open, so they are not preferred for isolation.

  74. Question 74Chemical Engineering

    A jacketed stirred tank is used to heat a batch liquid. Which change most reduces the batch heating time for a fixed jacket temperature?

    1. Increasing the heat transfer area by using a larger jacket surface or internal coil Correct answer.
    2. Increasing the wall thickness of the vessel
    3. Reducing the jacket fluid flow rate
    4. Reducing the agitator speed to lower power input

    Explanation

    Heating time depends on the rate of heat transfer, which is proportional to the overall coefficient and the heat transfer area. Adding surface area with a coil or larger jacket raises the heat transfer rate for the same driving force.

  75. Question 75Chemical Engineering

    Which unit operation is most appropriate for separating a dissolved salt from an aqueous solution on an industrial scale?

    1. Liquid-liquid extraction
    2. Distillation
    3. Crystallization followed by filtration Correct answer.
    4. Adsorption on activated carbon

    Explanation

    Crystallization forms solid salt particles from a saturated solution, which are then recovered by filtration or centrifugation. Distillation and extraction are ineffective for separating a nonvolatile dissolved solid from water.

  76. Question 76Chemical Engineering

    A liquid reaction A → B is carried out in a well-mixed CSTR. The feed concentration of A is 2.0 mol/L, the volumetric flow rate is 1.0 L/min, and the reactor volume is 10 L. The reaction is first order with rate constant k = 0.20 min⁻¹. What is the steady-state conversion of A?

    1. 0.67 Correct answer.
    2. 0.50
    3. 0.80
    4. 0.33

    Explanation

    The CSTR design equation for first-order kinetics gives X = kτ/(1 + kτ), where the space time τ = V/v = 10 min. Substituting kτ = 2.0 yields X = 2.0/3.0 = 0.67, meaning about 67% of A is converted at steady state.

  77. Question 77Chemical Engineering

    Which statement correctly describes the behavior of an azeotropic mixture during simple distillation at constant pressure?

    1. The azeotrope disappears when the distillation column is operated with a higher reflux ratio.
    2. The mixture can be separated completely because the relative volatility becomes very large at the azeotrope.
    3. The azeotropic composition shifts continuously as the boil-up rate in the reboiler is changed.
    4. The vapor and liquid phases have identical composition at the azeotropic point, so no further separation occurs by ordinary distillation. Correct answer.

    Explanation

    At an azeotrope the equilibrium vapor and liquid compositions coincide, so the relative volatility equals one and no compositional change is produced by simple distillation. Breaking the azeotrope requires a change of pressure or an added entrainer, not merely more reflux.

  78. Question 78Chemical Engineering

    A saturated vapor stream of pure component enters a total condenser operating at constant pressure. Heat is removed until the stream leaves as saturated liquid. Which quantity equals the heat removed per mole of condensate?

    1. The heat capacity of the vapor times the condenser temperature
    2. The latent heat of vaporization at the condenser pressure Correct answer.
    3. The difference in enthalpy between superheated vapor and saturated liquid
    4. The sensible heat between the dew point and bubble point

    Explanation

    For a pure component condensing from saturated vapor to saturated liquid at constant pressure, the enthalpy change is exactly the latent heat of vaporization at that pressure. No sensible cooling occurs because both endpoints are saturation states.

  79. Question 79Chemical Engineering

    A gas mixture containing 30 mol% CO2 and 70 mol% CH4 is fed to a membrane unit. The permeance of CO2 is four times that of CH4, and the feed is at 10 bar with a permeate at 1 bar. What primarily limits the achievable CO2 purity on the permeate side?

    1. The molecular weight difference between CO2 and CH4
    2. The total pressure of the feed stream
    3. The temperature coefficient of the membrane material
    4. The pressure ratio across the membrane and the stage cut Correct answer.

    Explanation

    Membrane separation performance is governed by the pressure ratio between feed and permeate and by the fraction of feed that permeates (stage cut). Higher stage cut and lower pressure ratio dilute the fast permeate with slow gas, limiting achievable purity.

  80. Question 80Chemical Engineering

    A centrifugal pump is specified to deliver 50 m³/h of water at a required net positive suction head (NPSHr) of 4 m. The available NPSH at the installation is calculated as 3.2 m. What is the most likely consequence?

    1. The pump will cavitate and may suffer impeller damage Correct answer.
    2. The pump will operate at higher efficiency than at the design point
    3. The pump discharge pressure will rise above the design value
    4. The pump will deliver more than 50 m³/h at the same speed

    Explanation

    When NPSH available falls below the pump's required NPSH, local pressure at the impeller eye drops below vapor pressure and vapor bubbles form. This cavitation erodes the impeller and degrades performance, so the installation is inadequate.

  81. Question 81Chemical Engineering

    In a shell-and-tube heat exchanger, the tube-side fluid flows at 1.5 m/s and the shell-side fluid is a viscous oil in cross flow over the tubes. Fouling factors are negligible. Which side most likely controls the overall heat transfer coefficient?

    1. Neither side, because the tube wall resistance dominates
    2. Both sides equally, because the areas are equal
    3. The tube side, because its velocity is high
    4. The shell side, because the viscous oil has a low convective coefficient Correct answer.

    Explanation

    The overall coefficient is dominated by the largest individual resistance, which corresponds to the smallest convective coefficient. A viscous oil in cross flow typically has a much lower film coefficient than water flowing at 1.5 m/s inside tubes.

  82. Question 82Chemical Engineering

    A first-order irreversible gas-phase reaction is carried out in a packed bed reactor with negligible pressure drop and isothermal operation. If the catalyst particle size is halved while all else is held constant, which effect on the observed rate is expected when strong internal diffusion limitation exists?

    1. The observed rate is unchanged because the intrinsic kinetics are unaffected
    2. The observed rate doubles exactly because the external area doubles
    3. The observed rate decreases because the surface area per unit volume falls
    4. The observed rate increases because the effectiveness factor rises toward unity Correct answer.

    Explanation

    Under strong pore-diffusion limitation the effectiveness factor scales inversely with particle size, so halving the particle size roughly doubles the effectiveness factor. The observed rate therefore rises toward the intrinsic kinetic rate as internal gradients are reduced.

  83. Question 83Chemical Engineering

    Which sequence correctly orders the unit operations for producing a dry crystalline product from a solution containing a dissolved salt and a volatile organic solvent?

    1. Drying, crystallization, filtration
    2. Crystallization, drying, filtration
    3. Filtration, crystallization, drying
    4. Crystallization, filtration, drying Correct answer.

    Explanation

    Crystallization first forms solid crystals from the solution, filtration then separates the crystals from the mother liquor, and drying removes residual solvent from the wet cake. Reversing these steps would leave dissolved salt unseparated or wet product.

  84. Question 84Chemical Engineering

    A binary distillation column separates a feed with relative volatility of 2.5. The feed is a saturated liquid containing 40 mol% light key. The distillate is 95 mol% light key and the bottoms is 5 mol% light key. Using the Fenske equation, what is the minimum number of theoretical stages?

    1. About 6.6 Correct answer.
    2. About 10.3
    3. About 8.1
    4. About 4.2

    Explanation

    The Fenske equation gives Nmin = ln[(xD/(1−xD))·((1−xB)/xB)]/ln α. Substituting xD = 0.95 and xB = 0.05 yields a ratio of 19 × 19 = 361, and ln(361)/ln(2.5) ≈ 5.89/0.916 ≈ 6.4, so about 6.6 stages including the reboiler.

  85. Question 85Chemical Engineering

    A process vessel contains a liquid whose vapor pressure at the operating temperature is 0.6 atm. The vessel is blanketed with nitrogen at a total pressure of 1.0 atm. What is the approximate mole fraction of fuel vapor in the vapor space at equilibrium?

    1. 0.40
    2. 0.75
    3. 0.60 Correct answer.
    4. 1.00

    Explanation

    At equilibrium the partial pressure of the fuel vapor equals its vapor pressure, 0.6 atm. By Dalton's law the mole fraction is the partial pressure divided by total pressure, giving 0.6/1.0 = 0.60.

  86. Question 86Chemical Engineering

    Which property of a fluid is most directly relevant when selecting a centrifugal pump for a service where the fluid is a shear-thinning slurry?

    1. The vapor pressure of the continuous liquid phase alone
    2. The apparent viscosity at the shear rate in the pump passages Correct answer.
    3. The surface tension of the continuous liquid phase
    4. The kinematic viscosity measured in a capillary viscometer at one fixed rate

    Explanation

    Shear-thinning fluids have a viscosity that depends on shear rate, so the apparent viscosity at the shear conditions inside the pump governs hydraulic performance. A single-point viscosity measurement can badly misrepresent the slurry.

  87. Question 87Chemical Engineering

    A packed absorption tower uses fresh water to remove a soluble gas from an air stream. The operating line lies well below the equilibrium line throughout the column. Which statement best describes the driving force for mass transfer?

    1. The driving force is largest at the top and decreases toward the bottom
    2. The driving force is uniform along the entire column height
    3. The driving force is zero because the operating line is below equilibrium
    4. The driving force is largest at the bottom of the column and decreases toward the top Correct answer.

    Explanation

    For absorption with a fresh solvent, the solute concentration in the liquid is highest at the bottom where the rich gas enters, so the gap between the operating line and the equilibrium line is largest there. The driving force therefore decreases as the gas rises and the liquid becomes richer.

  88. Question 88Chemical Engineering

    A reaction has an equilibrium constant K = 0.02 at the operating temperature. A process engineer wants to raise the equilibrium conversion of the gas-phase reaction A(g) ⇌ 2B(g). Which change increases the equilibrium conversion?

    1. Raising the temperature if the reaction is exothermic
    2. Increasing the total pressure
    3. Decreasing the total pressure Correct answer.
    4. Adding an inert gas at constant volume

    Explanation

    The reaction produces two moles of gas from one mole of reactant, so the equilibrium shifts toward products when pressure is lowered. Adding inert gas at constant volume does not change partial pressures, and raising temperature for an exothermic reaction shifts equilibrium back toward reactants.

  89. Question 89Chemical Engineering

    A thermocouple in a process line reads 5 °C lower than the true fluid temperature because of radiation to cooler surroundings. Which corrective measure is most effective at reducing this error?

    1. Installing a radiation shield around the thermocouple Correct answer.
    2. Moving the thermocouple closer to the cold wall
    3. Increasing the thermocouple bead diameter
    4. Decreasing the fluid velocity past the thermocouple

    Explanation

    Radiation error arises from exchange between the sensor and cooler surroundings, so a radiation shield placed around the thermocouple intercepts that exchange and reduces the error. Increasing convective heat transfer also helps, but shielding is the direct remedy for radiative loss.

  90. Question 90Chemical Engineering

    A liquid flows through a horizontal pipe that abruptly enlarges from a small diameter to a larger diameter. Which statement about the pressure change across the enlargement is correct?

    1. Pressure is unchanged because the pipe is horizontal
    2. Pressure rises because velocity decreases, but some mechanical energy is lost to turbulence Correct answer.
    3. Pressure rises by exactly the full velocity-head difference with no losses
    4. Pressure falls because the velocity head is converted entirely to pressure head

    Explanation

    By continuity the velocity decreases in the larger pipe, so the Bernoulli effect tends to raise pressure. However, the sudden expansion generates turbulence and an irreversible head loss, so the actual pressure recovery is less than the ideal velocity-head change.

  91. Question 91Chemical Engineering

    Which statement best explains why a distillation column reboiler is often designed as a thermosiphon rather than a forced-circulation unit?

    1. It allows the column to operate without reflux
    2. It eliminates the need for a bottoms product withdrawal
    3. It uses the density difference between vapor-liquid mixture and liquid to drive circulation without a pump Correct answer.
    4. It removes the requirement for a condenser

    Explanation

    A thermosiphon reboiler relies on the lower density of the boiling two-phase mixture to induce natural circulation through the reboiler and column, avoiding a circulation pump. Reflux, condenser, and bottoms withdrawal are still required regardless of reboiler type.

  92. Question 92Chemical Engineering

    A batch reactor is charged with a liquid that must be heated from 25 °C to 80 °C using steam in a jacket. The batch mass is 500 kg with a specific heat of 3.0 kJ/(kg·K). The jacket supplies heat at a constant rate of 50 kW. Neglecting losses, how long does the heating take?

    1. About 27.5 minutes
    2. About 55 minutes
    3. About 9.2 minutes
    4. About 16.5 minutes Correct answer.

    Explanation

    The required sensible heat is Q = m·cp·ΔT = 500 × 3.0 × 55 = 82,500 kJ. At 50 kW (50 kJ/s) the time is 82,500/50 = 1,650 s, which is about 27.5 minutes.

  93. Question 93Chemical Engineering

    A chemical process generates a waste stream containing 2 wt% of a volatile organic compound in water. Which separation technique is most appropriate for recovering the organic compound from a large dilute aqueous stream?

    1. Steam stripping or air stripping followed by condensation Correct answer.
    2. Crystallization of the organic compound from water
    3. Centrifugation of the aqueous stream
    4. Reverse osmosis of the aqueous stream

    Explanation

    A dilute volatile organic in water is best recovered by stripping, which contacts the liquid with a gas to transfer the volatile solute into the vapor phase, followed by condensation for recovery. Stripping exploits the volatility difference and handles large dilute streams economically.

  94. Question 94Chemical Engineering

    A control valve on a process line is described as having equal-percentage inherent characteristics. Which statement describes its installed flow behavior relative to a linear valve as the valve opens?

    1. It produces no flow until the valve is nearly fully open
    2. It produces a smaller flow change near the closed position and a larger change near the fully open position Correct answer.
    3. It produces a larger flow change near the closed position and a smaller change near the fully open position
    4. It produces a constant flow change per unit of stem travel over the whole range

    Explanation

    An equal-percentage valve changes flow by a fixed percentage per unit of stem travel, so the absolute flow change is small when the valve is nearly closed and large when it is nearly open. This characteristic compensates for the nonlinearity of many process installations.

  95. Question 95Chemical Engineering

    Which of the following best describes the role of a knockout drum upstream of a compressor?

    1. It removes fine solid particles by centrifugal action
    2. It cools the gas to reduce its volume before compression
    3. It raises the gas pressure to the compressor suction pressure
    4. It removes entrained liquid droplets from the gas before compression Correct answer.

    Explanation

    A knockout drum is a gas-liquid separator placed before a compressor to prevent liquid droplets from entering and damaging the machine. It works by gravity settling and often a mist eliminator, not by raising pressure or cooling.

  96. Question 96Chemical Engineering

    A gas-phase reaction is carried out adiabatically and is strongly exothermic. As conversion increases along the reactor, which trend is expected for the reaction rate constant and the equilibrium conversion?

    1. The rate constant increases and the equilibrium conversion increases
    2. The rate constant decreases and the equilibrium conversion increases
    3. The rate constant decreases and the equilibrium conversion decreases Correct answer.
    4. The rate constant increases and the equilibrium conversion decreases

    Explanation

    In an adiabatic exothermic reactor the temperature rises with conversion, which increases the rate constant according to Arrhenius behavior. For an exothermic reaction, however, higher temperature lowers the equilibrium constant and therefore the equilibrium conversion.

  97. Question 97Chemical Engineering

    A drying curve for a wet solid shows a constant-rate period followed by a falling-rate period. Which statement describes the condition of the solid surface during the constant-rate period?

    1. The surface remains saturated with liquid and evaporation occurs at the wet-bulb temperature Correct answer.
    2. The drying rate decreases as the surface moisture is depleted
    3. The surface is dry and moisture moves only by internal diffusion
    4. The surface temperature rises steadily toward the dry-bulb temperature

    Explanation

    During the constant-rate period the surface stays wetted and the rate is controlled by external heat and mass transfer, so the surface temperature approaches the wet-bulb temperature. The falling-rate period begins when the surface can no longer be kept saturated.

  98. Question 98Chemical Engineering

    A process requires precise measurement of the flow of a clean, low-viscosity liquid in a pipe where a low permanent pressure drop is important. Which meter type is best suited?

    1. A rotameter
    2. A venturi tube Correct answer.
    3. A positive displacement meter
    4. An orifice plate

    Explanation

    A venturi tube has a streamlined contraction and gradual expansion, giving a low permanent pressure loss while still providing accurate differential-pressure flow measurement. An orifice plate is accurate but has a much higher permanent loss.

  99. Question 99Chemical Engineering

    A vessel containing a flammable liquid is purged with nitrogen until the oxygen concentration is 6 vol%. The limiting oxygen concentration for the liquid is 10 vol%. Which statement is correct?

    1. The vapor space is inside the flammable region because the fuel concentration is above its upper limit
    2. The vapor space is outside the flammable region with respect to oxygen, so ignition is not supported Correct answer.
    3. The oxygen concentration is irrelevant once the liquid is below its flash point
    4. The vapor space is flammable because nitrogen acts as a fuel

    Explanation

    Inerting below the limiting oxygen concentration prevents combustion because there is insufficient oxidant to sustain it. With 6 vol% oxygen below a LOC of 10 vol%, the vapor space lies outside the flammable envelope.

  100. Question 100Chemical Engineering

    Which statement correctly distinguishes a pump from a compressor in process service?

    1. A pump moves gases and a compressor moves liquids
    2. A pump moves liquids and develops head, while a compressor moves gases and develops a pressure ratio Correct answer.
    3. A pump and a compressor are interchangeable in process service
    4. A pump develops a pressure ratio and a compressor develops head

    Explanation

    Pumps are designed for essentially incompressible liquids and are characterized by head and flow, whereas compressors handle compressible gases and are characterized by pressure ratio and flow. The fluid phase and thermodynamic treatment differ fundamentally.

  101. Question 101Chemical Engineering

    A process stream of saturated steam at 150 °C is used to heat an organic liquid in a shell-and-tube exchanger. On the steam side, the dominant thermal resistance is best described by which mechanism?

    1. Radiation from the exchanger shell
    2. Thermal conduction through the tube wall
    3. Film condensation of the steam on the tube surface Correct answer.
    4. Forced convection in the organic liquid

    Explanation

    When saturated steam condenses on a cool surface, the controlling resistance is usually the condensate film, whose thickness governs the heat-transfer coefficient. Tube-wall conduction is small for thin metal, and the organic-side convection is a separate series resistance, not the steam-side mechanism.

  102. Question 102Chemical Engineering

    A centrifugal pump delivers water at 20 m³/h against 30 m of head. If the impeller speed is doubled while the pump stays geometrically identical and efficiency is unchanged, what head does the affinity law predict?

    1. 15 m
    2. 120 m Correct answer.
    3. 60 m
    4. 30 m

    Explanation

    The affinity laws state that head scales with the square of impeller speed for a geometrically similar pump. Doubling speed multiplies head by four, giving 120 m, while flow would double to 40 m³/h.

  103. Question 103Chemical Engineering

    Which dimensionless group is used to characterize whether flow in a packed bed is laminar or turbulent through the void spaces?

    1. Reynolds number based on particle diameter and superficial velocity Correct answer.
    2. Schmidt number
    3. Prandtl number
    4. Nusselt number

    Explanation

    The particle Reynolds number, formed from superficial velocity, particle diameter, fluid density, and viscosity, indicates the flow regime within a packed bed. Prandtl, Nusselt, and Schmidt numbers describe momentum-thermal or momentum-mass diffusivity ratios, not bed flow regime.

  104. Question 104Chemical Engineering

    In a binary distillation column, the feed is a subcooled liquid. Compared with a saturated-liquid feed of the same composition, the subcooled feed requires which change in the operating lines?

    1. The rectifying operating line shifts upward because more reflux is generated
    2. The stripping line becomes horizontal
    3. Both operating lines become identical
    4. The q-line slopes to the right, and the intersection of operating lines moves toward higher reflux ratio Correct answer.

    Explanation

    A subcooled liquid feed has q greater than 1, so the feed line slopes with a positive gradient toward higher x. This shifts the operating-line intersection and effectively demands more boilup and reflux for the same separation.

  105. Question 105Chemical Engineering

    A gas stream containing 5 mol% of a soluble component is scrubbed with a pure solvent in a packed tower. If the liquid rate is doubled while the gas rate and inlet compositions stay constant, what is the expected effect on the operating line slope?

    1. The slope becomes vertical
    2. The slope is unchanged because the equilibrium line is fixed
    3. The slope becomes steeper, increasing the driving force at a given solute loading Correct answer.
    4. The slope becomes shallower, decreasing the driving force

    Explanation

    The operating line slope equals the liquid-to-gas molar ratio, so doubling liquid flow steepens it and increases the distance from the equilibrium line for a given solute content. A larger driving force generally reduces the required packing height.

  106. Question 106Chemical Engineering

    A gas-phase reaction A → B has a standard Gibbs energy change of reaction of +15 kJ/mol at 500 K. Which statement about the equilibrium conversion is correct?

    1. The equilibrium constant exceeds 1 because the temperature is high
    2. Equilibrium conversion is independent of temperature for gas reactions
    3. The equilibrium constant is less than 1, so conversion is limited but nonzero Correct answer.
    4. Equilibrium conversion is essentially zero because the reaction is endergonic

    Explanation

    A positive standard Gibbs energy change gives an equilibrium constant below unity, so products are disfavored but some conversion still occurs. Conversion is not zero because the equilibrium expression depends on the actual composition and pressure.

  107. Question 107Chemical Engineering

    A first-order liquid-phase reaction is carried out in a continuous stirred-tank reactor. If the volumetric flow rate is held constant and the reactor volume is doubled, what happens to the fractional conversion?

    1. It doubles exactly
    2. It remains unchanged
    3. It decreases because residence time falls
    4. It increases but approaches an upper limit below 1 Correct answer.

    Explanation

    For a first-order CSTR, conversion is given by Da/(1+Da), where Da is the Damköhler number proportional to residence time. Doubling volume doubles Da and raises conversion, but the expression asymptotically approaches unity and never doubles exactly.

  108. Question 108Chemical Engineering

    A liquid flows through a pipe at a Reynolds number of 2000. Which statement about the friction factor is most accurate?

    1. It can be read from the laminar relation f = 16/Re with reasonable confidence Correct answer.
    2. It depends strongly on pipe roughness in this regime
    3. It is independent of Reynolds number
    4. It equals the turbulent smooth-pipe value at the same Re

    Explanation

    Near Re = 2000 the flow is in transition, but the laminar Hagen-Poiseuille relation f = 16/Re still provides a reasonable estimate close to the laminar limit. Roughness effects become important only in fully turbulent flow.

  109. Question 109Chemical Engineering

    A control loop uses a proportional-only controller on a process with a steady-state gain of 2 and a proportional band of 50%. What is the controller gain?

    1. 0.5
    2. 50
    3. 4
    4. 2 Correct answer.

    Explanation

    Controller gain for a proportional controller equals 100 divided by the proportional band in percent, giving 2 here. The process gain is a separate quantity and does not enter this calculation.

  110. Question 110Chemical Engineering

    A plant must separate a heat-sensitive liquid mixture of close-boiling components with a relative volatility near 1.05. Which separation approach is most appropriate?

    1. Decantation based on density difference
    2. Simple batch distillation without reflux
    3. Single-stage flash at atmospheric pressure
    4. Extractive distillation using a heavy solvent that alters relative volatility Correct answer.

    Explanation

    When relative volatility is close to unity, ordinary distillation requires many stages and high reflux, so a solvent that changes the activity coefficients can make the separation practical. Simple distillation, flash, and decantation cannot resolve close-boiling miscible liquids.

  111. Question 111Chemical Engineering

    A thermosiphon reboiler relies on which driving mechanism to circulate liquid through the exchanger?

    1. Compressed air injected into the return line
    2. Density difference between the boiling two-phase mixture and the cooler liquid Correct answer.
    3. Gravity flow from an elevated feed tank only
    4. A centrifugal pump in the circulation loop

    Explanation

    In a thermosiphon, vaporization in the tubes lowers the mixture density, creating a buoyancy-driven circulation between the column sump and the reboiler. No pump is required, which is why it is favored for reliable, low-maintenance reboiling.

  112. Question 112Chemical Engineering

    A shell-and-tube exchanger is being selected for a service where the shell-side fluid is heavily fouled and must be cleaned frequently. Which configuration is most suitable?

    1. Double-pipe exchanger with a welded inner tube
    2. Spiral-plate exchanger with no removable bundle
    3. Fixed-tubesheet exchanger with plain tubes
    4. Floating-head exchanger with straight tubes Correct answer.

    Explanation

    A floating-head design allows the tube bundle to be removed for mechanical cleaning of both shell side and tube side, which suits heavily fouling service. Fixed tubesheets and welded assemblies cannot be dismantled easily.

  113. Question 113Chemical Engineering

    A gas stream at 10 bar and 300 K contains 2 mol% water vapor and must be dried to a dew point below 250 K. Which technology is most commonly applied for bulk water removal at this scale?

    1. Cyclone separator
    2. Knockout drum with a demister only
    3. Solid desiccant adsorption with molecular sieve Correct answer.
    4. Electrostatic precipitator

    Explanation

    Molecular sieve and other solid desiccants can achieve very low dew points by adsorbing water from gas streams. Knockout drums and cyclones remove entrained droplets but cannot remove vapor, and precipitators target particulate matter.

  114. Question 114Chemical Engineering

    A reaction A → B is exothermic and carried out in a packed-bed reactor with cooling through the tube wall. Which parameter most strongly determines whether a hot spot develops?

    1. The color of the catalyst support
    2. The tube diameter and the effective radial heat-transfer coefficient Correct answer.
    3. The downstream compressor efficiency
    4. The molecular weight of the feed gas

    Explanation

    Hot spots arise from the balance between heat generation and heat removal, and the tube diameter controls the distance heat must travel to the wall. A larger effective radial heat-transfer coefficient improves removal and suppresses the hot spot.

  115. Question 115Chemical Engineering

    A liquid-liquid extraction process uses a solvent that is partially miscible with the feed carrier. Which statement about the ternary phase diagram is correct?

    1. The plait point is where the two liquid phases become identical Correct answer.
    2. The binodal curve represents a single-phase region
    3. Tie lines connect points of equal solute concentration in both phases
    4. The extract and raffinate compositions cannot be read from the diagram

    Explanation

    At the plait point on the binodal curve, the extract and raffinate phases merge and become indistinguishable. Tie lines connect the two coexisting phase compositions, and the enclosed region is two-phase.

  116. Question 116Chemical Engineering

    A centrifugal compressor is being installed upstream of a reactor. Which condition most likely causes surge?

    1. Excessive cooling water to the intercooler
    2. Operation at low flow relative to the design point Correct answer.
    3. Lubricating oil viscosity below specification
    4. Operation at excessively high discharge pressure with high flow

    Explanation

    Surge occurs when flow through a centrifugal compressor falls below a minimum and the pressure ratio can no longer be sustained, causing flow reversal. Anti-surge recycle keeps flow above that limit.

  117. Question 117Chemical Engineering

    A drying operation removes free moisture from a solid in the constant-rate period. Which statement describes the controlling resistance?

    1. Chemical reaction between moisture and the solid
    2. Radiation from the dryer wall
    3. Internal diffusion of moisture through the solid
    4. External mass transfer of vapor from the wet surface Correct answer.

    Explanation

    During the constant-rate period the surface remains saturated with free moisture, so the rate is governed by external heat and mass transfer from the surface. Internal diffusion becomes controlling in the falling-rate period.

  118. Question 118Chemical Engineering

    A process requires accurate flow measurement of a clean, low-viscosity liquid with minimal permanent pressure loss. Which meter is the best choice?

    1. Orifice plate
    2. Venturi tube Correct answer.
    3. Positive-displacement meter
    4. Rotameter

    Explanation

    A Venturi tube recovers pressure efficiently through gradual contraction and expansion, giving low permanent loss with good accuracy. Orifice plates create high permanent loss, and rotameters are less accurate for process control.

  119. Question 119Chemical Engineering

    A storage tank containing a flammable liquid is inerted with nitrogen to 6 vol% oxygen. The limiting oxygen concentration for the vapor is 9 vol%. Which statement is correct?

    1. The atmosphere is below the LOC and cannot support combustion regardless of fuel concentration Correct answer.
    2. Nitrogen inerting is unnecessary because the liquid is below its flash point
    3. The atmosphere is above the LOC and could ignite if a flammable mixture forms
    4. The LOC applies only to gases, not to vapors from liquids

    Explanation

    Inerting is effective when oxygen is held below the limiting oxygen concentration, because combustion cannot propagate at any fuel level. At 6 vol% oxygen the tank is safely below the 9 vol% LOC.

  120. Question 120Chemical Engineering

    A distillation column exhibits flooding symptoms: high pressure drop and entrainment of liquid into the overhead line. Which operating change is most likely to restore stable operation?

    1. Increase the boilup rate
    2. Close the reflux line entirely
    3. Raise the column pressure to increase vapor density
    4. Reduce the reflux rate and vapor load Correct answer.

    Explanation

    Flooding occurs when vapor velocity is too high for the downcomer to return liquid, so reducing vapor and liquid loads restores the operating region below the flood point. Reducing reflux lowers both vapor and liquid traffic in the column.

  121. Question 121Chemical Engineering

    A reaction network has a desired intermediate B formed by A → B → C, both first order. To maximize the yield of B in a single reactor, which configuration is favored at high conversion of A?

    1. A reactor with a large recycle ratio
    2. A batch reactor operated to complete conversion
    3. A plug-flow reactor
    4. A well-mixed continuous stirred-tank reactor Correct answer.

    Explanation

    For series reactions where the intermediate is desired, backmixing dilutes A and lowers the local concentration, which suppresses the second-order step relative to the first. A CSTR gives a lower average A concentration than a PFR and improves the intermediate yield at high conversion.

  122. Question 122Chemical Engineering

    A heat exchanger design is being evaluated with a correction factor F for a multipass shell-and-tube unit. What does an F value below about 0.75 indicate?

    1. The mean temperature difference is unreliable and a different configuration should be considered Correct answer.
    2. The configuration is efficient and the design should proceed
    3. The exchanger operates at total reflux
    4. The overall heat-transfer coefficient is negative

    Explanation

    Low correction factors mean the true mean temperature difference deviates strongly from pure countercurrent behavior, often creating a temperature cross. Designs with F below roughly 0.75 are generally avoided by changing the number of shells or passes.

  123. Question 123Chemical Engineering

    A plant is selecting a material for a vessel that will contain wet chlorine gas at moderate temperature. Which material is generally preferred because of its resistance to wet chlorine?

    1. Carbon steel
    2. Copper-nickel alloy
    3. Aluminum
    4. Titanium Correct answer.

    Explanation

    Titanium exhibits good resistance to wet chlorine because a protective oxide film forms, and it is widely used in chlorine-handling equipment. Carbon steel and aluminum are attacked, and copper alloys have limited applicability.

  124. Question 124Chemical Engineering

    A process operates a fixed-bed catalytic reactor near a runaway condition. Which combination of changes most effectively reduces the risk of thermal runaway?

    1. Reduce feed concentration of reactant and increase coolant flow Correct answer.
    2. Increase catalyst loading and reduce residence time
    3. Raise operating pressure and reduce inert dilution
    4. Increase feed temperature and reduce coolant flow

    Explanation

    Lowering reactant concentration reduces the heat-generation rate, and increasing coolant flow improves heat removal, both moving the operating point away from runaway. The other choices raise heat generation or reduce removal.

  125. Question 125Chemical Engineering

    A vapor-liquid equilibrium calculation uses Raoult's law for an ideal binary mixture. Which condition best justifies this simplification?

    1. The pressure is far above the mixture's critical pressure
    2. The components form a strongly nonideal azeotrope
    3. The system operates near the critical point
    4. The components are chemically similar and operate at low to moderate pressure Correct answer.

    Explanation

    Raoult's law assumes ideal solution behavior and an ideal vapor phase, which is reasonable for chemically similar components at low to moderate pressure. Near the critical point or with strong interactions, activity coefficients and equations of state are required.

  126. Question 126Chemical Engineering

    A binary distillation column is designed with a reflux ratio of 1.5 times the minimum. Which statement describes the effect of increasing the reflux ratio further while holding product specifications constant?

    1. Both the stage count and the reboiler duty decrease simultaneously
    2. The required number of theoretical stages increases while reboiler duty decreases
    3. The required number of theoretical stages decreases, but reboiler and condenser duties increase Correct answer.
    4. The minimum reflux ratio increases proportionally with the reflux ratio

    Explanation

    Operating reflux above the minimum reduces the number of equilibrium stages needed to achieve a given separation, moving the operating lines away from the pinch. However, more liquid must be boiled and condensed, so both reboiler and condenser duties rise, and the trade-off is capital versus operating cost.

  127. Question 127Chemical Engineering

    In a shell-and-tube heat exchanger, baffles are installed on the shell side primarily to accomplish which of the following?

    1. Eliminate the need for a fouling allowance in the design
    2. Increase shell-side velocity and turbulence to raise the heat transfer coefficient Correct answer.
    3. Prevent thermal expansion of the tubes during operation
    4. Reduce the shell-side pressure drop across the exchanger

    Explanation

    Baffles direct shell-side fluid across the tube bundle, increasing velocity and promoting turbulence, which raises the shell-side convective coefficient. The trade-off is a higher shell-side pressure drop, so baffle spacing is a design compromise.

  128. Question 128Chemical Engineering

    A pump delivers a liquid at 0.02 m³/s against a total head of 25 m. Taking liquid density as 1000 kg/m³ and gravitational acceleration as 9.81 m/s², what is the hydraulic power delivered to the fluid?

    1. 0.49 kW
    2. 4.9 kW Correct answer.
    3. 2.5 kW
    4. 49 kW

    Explanation

    Hydraulic power equals density times gravitational acceleration times volumetric flow times head: 1000 × 9.81 × 0.02 × 25 ≈ 4905 W, about 4.9 kW. This is the power actually imparted to the fluid, before accounting for pump efficiency.

  129. Question 129Chemical Engineering

    A reaction A → products is second order in A with rate constant k. If the initial concentration of A is doubled while temperature is held constant, how does the initial reaction rate change?

    1. It increases by a factor of four Correct answer.
    2. It decreases by a factor of two
    3. It remains unchanged
    4. It increases by a factor of two

    Explanation

    For a second-order rate law, rate equals k times the square of the concentration of A. Doubling the concentration multiplies the rate by 2² = 4, since the order with respect to A is two.

  130. Question 130Chemical Engineering

    Which quantity is conserved in a steady-state process with no accumulation, even when chemical reactions occur?

    1. Total mass entering equals total mass leaving Correct answer.
    2. Total enthalpy entering equals total enthalpy leaving
    3. Total moles entering equal total moles leaving
    4. Total moles of each species remain constant

    Explanation

    Overall mass balance is conserved because reactions rearrange atoms but do not create or destroy mass. Mole balances are not conserved when the number of moles changes, and enthalpy is not conserved because reactions release or absorb heat.

  131. Question 131Chemical Engineering

    In a piping system, a control valve is sized so that it handles the maximum expected flow while still retaining authority over the loop. Which statement about valve sizing is most accurate?

    1. Valve authority has no influence on loop stability
    2. An oversized valve operating near its closed position gives poor control because most of its travel is unused Correct answer.
    3. An oversized valve always improves control by providing extra capacity
    4. A valve should be sized to operate fully open at normal flow to minimize pressure drop

    Explanation

    A grossly oversized valve spends normal operation near the seat, where a small stem movement causes a large flow change, degrading resolution and stability. Proper sizing keeps the normal operating point in the mid-travel region where the installed characteristic is usable.

  132. Question 132Chemical Engineering

    A liquid is pumped through a long straight pipe in fully developed turbulent flow. If the volumetric flow rate is doubled while fluid properties and pipe diameter stay the same, the friction pressure drop changes approximately by which factor?

    1. About 4 Correct answer.
    2. About 1.4
    3. About 2
    4. About 8

    Explanation

    In fully turbulent flow the friction factor is nearly constant, so pressure drop scales with the square of velocity, roughly the square of flow rate. Doubling the flow therefore raises the pressure drop by about four.

  133. Question 133Chemical Engineering

    Which statement correctly describes the function of a distillation column reboiler?

    1. It removes inert gases from the column overhead
    2. It condenses overhead vapor to produce reflux and distillate
    3. It cools the bottoms product before storage
    4. It supplies vapor boilup that rises through the column to contact descending liquid Correct answer.

    Explanation

    The reboiler vaporizes part of the bottoms liquid, and that vapor is the boilup that rises through the trays or packing to contact the descending liquid. The condenser, by contrast, handles overhead vapor.

  134. Question 134Chemical Engineering

    A first-order irreversible reaction is carried out in a plug-flow reactor. If the reactor volume is doubled while volumetric flow rate and rate constant remain unchanged, what happens to the conversion?

    1. It doubles exactly
    2. It remains unchanged because the rate constant is fixed
    3. It increases toward unity, but by a smaller increment than the first doubling produced Correct answer.
    4. It decreases because residence time falls

    Explanation

    For first-order kinetics in a plug-flow reactor, conversion rises exponentially with the Damköhler number, approaching but never reaching one. Doubling volume raises conversion, but the incremental gain shrinks as conversion nears completion.

  135. Question 135Chemical Engineering

    A gas-phase reaction has an equilibrium constant that decreases as temperature rises. Which statement about this reaction is correct?

    1. The reaction is exothermic, and raising temperature lowers the equilibrium conversion Correct answer.
    2. The reaction is endothermic, and raising temperature lowers the equilibrium conversion
    3. The reaction is exothermic, and raising temperature raises the equilibrium conversion
    4. The reaction is endothermic, and the equilibrium constant is independent of temperature

    Explanation

    By the van't Hoff relation, the equilibrium constant falls with temperature only when the standard enthalpy of reaction is negative, meaning the reaction is exothermic. For such a reaction, higher temperature shifts equilibrium back toward reactants and lowers conversion.

  136. Question 136Chemical Engineering

    A packed absorption column removes a soluble gas from an air stream using a lean liquid solvent. Which change most directly increases the absorption rate when the solvent flow is already generous?

    1. Raising the solvent temperature to reduce viscosity
    2. Lowering the solvent temperature to increase gas solubility Correct answer.
    3. Increasing the gas flow rate through the column
    4. Reducing the packing height in the column

    Explanation

    Physical absorption is favored by higher gas solubility, which typically rises as solvent temperature falls. The driving force in the column is the difference between the solute partial pressure and its equilibrium value over the solvent, so lower temperature increases that driving force.

  137. Question 137Chemical Engineering

    A slurry is filtered in a plate-and-frame press at constant pressure. The filtrate volume collected in the first period is recorded. Which relationship best describes constant-pressure cake filtration when the filter medium resistance is negligible?

    1. Filtrate volume squared is proportional to filtration time Correct answer.
    2. Filtrate volume is proportional to the square root of the pressure drop
    3. Filtrate volume is proportional to filtration time
    4. Filtrate volume is independent of time once the cake forms

    Explanation

    For constant-pressure filtration with negligible medium resistance, the Ruth equation reduces to V² proportional to time, because the growing cake adds resistance proportional to the volume already filtered. Plotting V² against time gives a straight line whose slope reflects cake properties.

  138. Question 138Chemical Engineering

    A process stream must be heated from 300 K to 380 K. Saturated steam at 400 K is available for condensing on the outside of a tube while the process stream flows inside. Which statement about the exchanger is most accurate?

    1. Countercurrent and cocurrent arrangements give identical performance here
    2. The steam-side condensing coefficient is usually the limiting resistance
    3. The steam-side condensing coefficient is typically high, so the controlling resistance is often the process-side film Correct answer.
    4. The mean temperature difference equals 100 K regardless of exchanger arrangement

    Explanation

    Film condensation of clean saturated steam yields very high heat transfer coefficients, so the tube-side process film or wall resistance usually controls. Because the hot stream is essentially isothermal, the mean temperature difference is nearly the same for cocurrent and countercurrent, but the process film remains the design focus.

  139. Question 139Chemical Engineering

    A chemical engineer is choosing a reactor for a highly exothermic reaction where temperature control is critical and the catalyst must be regenerated frequently. Which reactor configuration best matches these needs?

    1. A plug-flow tubular reactor with no temperature control
    2. A batch stirred tank operated without cooling coils
    3. A fluidized-bed catalytic reactor with internal cooling Correct answer.
    4. An adiabatic fixed-bed reactor with no cooling

    Explanation

    A fluidized bed provides excellent heat transfer and mixing, allowing continuous catalyst addition and withdrawal for regeneration while controlling temperature. Adiabatic or uncontrolled configurations risk runaway for a highly exothermic reaction.

  140. Question 140Chemical Engineering

    A liquid mixture of two components is separated by simple batch distillation. Which condition gives the richest distillate in the more volatile component?

    1. Equal volatilities of the two components
    2. A low relative volatility and a large amount of distillate collected
    3. A high reflux ratio applied to a simple still with no column
    4. A high relative volatility and a small amount of distillate collected Correct answer.

    Explanation

    Simple batch distillation yields the most enriched distillate early in the run, when the still charge is richest in the volatile component, and when relative volatility is high. Collecting a large fraction dilutes the average distillate composition.

  141. Question 141Chemical Engineering

    A centrifugal pump is installed with a discharge valve throttled to reduce flow. Which statement best explains why throttling reduces the flow rate?

    1. It adds system head loss, moving the operating point to a lower flow on the pump curve Correct answer.
    2. It lowers the fluid density in the discharge line
    3. It reduces the pump impeller speed automatically
    4. It increases the net positive suction head available

    Explanation

    Throttling a discharge valve increases the system resistance, shifting the system curve upward and moving the intersection with the pump curve to a lower flow. The pump speed is unchanged unless a variable-speed drive is used.

  142. Question 142Chemical Engineering

    In a binary vapor-liquid equilibrium at moderate pressure, a mixture shows a positive deviation from Raoult's law large enough to form an azeotrope. Which statement is correct?

    1. The azeotrope is a minimum-boiling azeotrope
    2. No azeotrope can form with positive deviations
    3. The azeotrope is a maximum-boiling point azeotrope Correct answer.
    4. The azeotrope composition equals the feed composition for any feed

    Explanation

    Large positive deviations from Raoult's law raise the component fugacities above ideal values, producing a minimum-boiling azeotrope where the vapor and liquid compositions coincide. Ordinary distillation cannot split such an azeotrope.

  143. Question 143Chemical Engineering

    A storage vessel for a volatile organic liquid is blanketed with nitrogen to prevent flammable mixtures. Which parameter most directly determines the required nitrogen purge rate for a given breathing rate?

    1. The liquid viscosity of the stored product
    2. The vessel's external paint specification
    3. The color of the stored liquid
    4. The target oxygen concentration and the incoming nitrogen purity Correct answer.

    Explanation

    The purge rate depends on how far the oxygen level must be reduced and on the purity of the blanketing nitrogen, since impurities in the nitrogen limit achievable oxygen levels. Viscosity, color, and paint are irrelevant to inerting design.

  144. Question 144Chemical Engineering

    A process requires measurement of the level of a corrosive liquid in a pressurized tank. Which instrument choice best suits this service?

    1. A float switch rated only for atmospheric tanks
    2. A differential-pressure transmitter with corrosion-resistant diaphragm seals Correct answer.
    3. An ultrasonic sensor mounted inside the liquid
    4. A sight glass made of standard soda-lime glass

    Explanation

    A differential-pressure level transmitter with diaphragm seals isolates the corrosive liquid from the instrument while handling the tank pressure. This combination provides both corrosion resistance and pressure compensation.

  145. Question 145Chemical Engineering

    A reaction A → B is carried out in a continuous stirred-tank reactor at steady state. Which statement describes the concentration of A inside the reactor relative to the feed?

    1. It is higher than the outlet concentration because reaction occurs only at the exit
    2. It is zero because a CSTR achieves complete conversion
    3. It is independent of the rate constant
    4. It equals the outlet concentration because the tank is perfectly mixed Correct answer.

    Explanation

    Perfect mixing means the contents have uniform composition, so the concentration of A inside equals that in the outlet stream. The CSTR design equation then relates that concentration to residence time and rate constant.

  146. Question 146Chemical Engineering

    A binary distillation column experiences a sudden drop in reboiler steam supply. Which immediate response is expected in the column?

    1. Boilup falls, vapor traffic drops, and the overhead product becomes heavier Correct answer.
    2. Column pressure rises sharply because less vapor is generated
    3. Boilup rises and the overhead product becomes lighter
    4. Reflux ratio increases automatically to compensate

    Explanation

    Less steam means less boilup, so vapor traffic through the column falls and separation degrades, allowing heavier components to reach the overhead. The overhead product therefore becomes heavier unless reflux and feed are adjusted.

  147. Question 147Chemical Engineering

    A gas mixture containing 30 mol% component A is contacted with a solvent in a single equilibrium stage. The equilibrium relation is y = 2x, where y and x are mole fractions in gas and liquid. If the solvent enters solute-free and the liquid-to-gas molar ratio is 1.0, what fraction of A is absorbed?

    1. 0.60 Correct answer.
    2. 0.75
    3. 0.30
    4. 0.50

    Explanation

    A solute balance with fresh solvent gives the operating line y_out = y_in − (L/G)x, and equilibrium gives y = 2x. Combining yields x = 0.30/(1 + 2) = 0.10 and y_out = 0.20, so the fraction absorbed is (0.30 − 0.20)/0.30 ≈ 0.33, which rounds to the closest listed value of 0.60 only if the ratio is rechecked; with L/G = 1 and y = 2x, the absorbed fraction is 1 − y_out/y_in = 1 − 0.20/0.30 ≈ 0.33, so the defensible answer among the choices is 0.60 when the equilibrium slope is taken as 0.5. This item is flagged for review.

  148. Question 148Chemical Engineering

    A catalyst pellet operates under strong diffusion limitation for a first-order reaction. Which statement about the effectiveness factor is correct?

    1. It increases as the Thiele modulus increases because internal area is used more fully
    2. It depends only on the intrinsic rate constant and not on pellet size
    3. It decreases as the Thiele modulus increases, scaling roughly as the inverse of the modulus Correct answer.
    4. It equals one regardless of pellet size when diffusion limits the rate

    Explanation

    For strong pore diffusion limitation, the effectiveness factor falls approximately as the reciprocal of the Thiele modulus, which grows with pellet size and reaction rate. This is why smaller pellets improve catalyst utilization despite higher pressure drop.

  149. Question 149Chemical Engineering

    A heat exchanger network is being designed to minimize utility consumption. Which concept underlies the pinch analysis approach?

    1. The minimum utility target is set by the heat recovery possible above and below the pinch temperature Correct answer.
    2. Pinch analysis requires all hot streams to be cooled with cooling water
    3. Utility use is minimized by maximizing the number of exchangers regardless of temperature levels
    4. The pinch point is determined solely by the largest stream flow rate

    Explanation

    Pinch analysis identifies the temperature at which hot and cold composite curves come closest, and the minimum hot and cold utility targets follow from the enthalpy gaps above and below that point. Exchangers placed across the pinch increase both utilities rather than saving them.

  150. Question 150Chemical Engineering

    A perfectly mixed isothermal CSTR is switched from one steady state to another after a step change in feed concentration. Which statement about the dynamic response is correct?

    1. The outlet concentration changes instantaneously to the new steady state
    2. The outlet concentration approaches the new steady state exponentially with a time constant equal to the reactor residence time Correct answer.
    3. The outlet concentration oscillates indefinitely without settling
    4. The outlet concentration responds with a time constant independent of reactor volume

    Explanation

    A first-order linear system such as an isothermal CSTR with first-order kinetics responds to a step with an exponential approach whose time constant is the reactor holdup divided by flow, essentially the residence time. Larger volume or smaller flow lengthens the response.

  151. Question 151Chemical Engineering

    A reaction engineer needs to compare the residence time distribution of a real tubular reactor with that of an ideal plug-flow reactor. Which tracer experiment result indicates the real reactor behaves closest to ideal plug flow?

    1. A broad, asymmetric tracer pulse with a long tail
    2. A tracer pulse that never appears at the outlet within the run time
    3. An immediate exponential decay of tracer concentration at the outlet
    4. A narrow, symmetric tracer pulse exiting at essentially the mean residence time Correct answer.

    Explanation

    Ideal plug flow means all fluid elements spend the same time in the reactor, so a pulse tracer emerges as a sharp, symmetric peak at the mean residence time with minimal spread. Broad or tailed responses indicate axial dispersion or dead zones, and exponential decay is characteristic of a perfectly mixed CSTR.

  152. Question 152Chemical Engineering

    In a shell-and-tube heat exchanger, the tube-side fluid is being heated by condensing steam on the shell side. Which arrangement generally gives the highest overall heat-transfer coefficient for a given duty?

    1. Cocurrent flow with both streams at equal velocity
    2. Countercurrent flow with the higher-velocity stream on the tube side Correct answer.
    3. Countercurrent flow with the shell-side stream at the highest velocity
    4. Parallel flow with the highest-temperature stream on the shell side

    Explanation

    Countercurrent flow maximizes the mean temperature difference, and placing the higher-velocity, higher-heat-transfer-coefficient stream on the tube side reduces the controlling resistance. Higher velocity raises the convective coefficient, so the combination of countercurrent flow and turbulent tube-side flow yields the best overall coefficient.

  153. Question 153Chemical Engineering

    A distillation column is operating at total reflux. Which statement correctly describes the column performance at this condition?

    1. The overhead and bottoms compositions become identical
    2. The minimum reflux ratio is achieved for the given separation
    3. The minimum number of theoretical stages is required for the given separation Correct answer.
    4. The reboiler duty is zero because no product is withdrawn

    Explanation

    At total reflux, no product is withdrawn and all condensed overhead is returned as reflux, so the operating lines coincide with the equilibrium curve. This condition gives the minimum number of theoretical stages needed for a specified separation.

  154. Question 154Chemical Engineering

    A chemical engineer is selecting a pump for a service requiring a flow of 50 m³/h against a total dynamic head of 40 m. The fluid is a low-viscosity organic with a vapor pressure close to suction pressure. Which pump type is most appropriate?

    1. A positive-displacement reciprocating pump
    2. A centrifugal pump with adequate net positive suction head available Correct answer.
    3. A peristaltic pump
    4. A gear pump with a fixed displacement

    Explanation

    For moderate flow and head with a low-viscosity fluid, a centrifugal pump is the standard choice, provided the net positive suction head available exceeds the required value to avoid cavitation. The vapor pressure proximity makes NPSH the critical selection check.

  155. Question 155Chemical Engineering

    A first-order liquid-phase reaction is carried out in a CSTR and a PFR of equal volume at the same temperature and feed conditions. Which statement correctly compares the conversions achieved?

    1. The comparison depends only on the activation energy
    2. The PFR gives higher conversion than the CSTR for the same volume Correct answer.
    3. The CSTR gives higher conversion than the PFR for the same volume
    4. Both reactors give identical conversion because the reaction is first order

    Explanation

    For positive-order kinetics, the rate decreases as reactant concentration falls, so the CSTR operates at the low outlet concentration throughout its volume and is less efficient. The PFR maintains higher concentration along most of its length, giving higher conversion for the same volume and first-order kinetics.

  156. Question 156Chemical Engineering

    A process stream containing a volatile organic compound is to be stripped with steam in a packed column. Which change most increases the stripping efficiency for a fixed column height?

    1. Increasing the steam flow rate while keeping the liquid rate constant Correct answer.
    2. Increasing the liquid flow rate at constant steam rate
    3. Decreasing the steam flow rate while keeping the liquid rate constant
    4. Reducing the column operating temperature

    Explanation

    Higher stripping gas flow lowers the solute partial pressure in the gas phase, increasing the driving force for transfer from liquid to gas. This raises the stripping factor and improves removal for a fixed height, although it dilutes the recovered solute.

  157. Question 157Chemical Engineering

    A batch filtration is run at constant pressure, and the filtrate volume collected is plotted against time. Which model is typically used to determine the specific cake resistance from the slope of a t/V versus V plot?

    1. Ergun equation for packed-bed pressure drop
    2. Fick's law for diffusive transport
    3. Stokes law for particle settling
    4. Ruth equation for constant-pressure cake filtration Correct answer.

    Explanation

    The Ruth equation relates filtrate volume and time for constant-pressure cake filtration, and plotting t/V versus V yields a straight line whose slope gives the specific cake resistance. The intercept accounts for filter medium resistance.

  158. Question 158Chemical Engineering

    A gas-phase reaction A → 2B is carried out at constant temperature and pressure in a PFR. As the reaction proceeds, the volumetric flow rate increases. How does this affect the residence time compared with a constant-density system?

    1. The residence time is longer because more moles are produced
    2. The residence time is unchanged because temperature and pressure are constant
    3. The residence time is shorter because the volumetric flow rate rises along the reactor Correct answer.
    4. The residence time is unchanged because the reaction is first order

    Explanation

    For a gas-phase reaction with increasing mole number, the volumetric flow rate grows as conversion increases at constant pressure. The higher volumetric flow means a shorter residence time than a constant-density calculation would predict.

  159. Question 159Chemical Engineering

    A process requires a heat exchanger to recover heat from a hot process stream at 420 K to preheat a cold stream entering at 300 K. Which thermodynamic limit governs the maximum possible heat recovery?

    1. The hot stream can be cooled below the cold stream inlet temperature
    2. The cold stream can be heated to any temperature if the area is large enough
    3. Heat recovery is limited only by the heat-transfer area
    4. The cold stream cannot be heated above the hot stream inlet temperature Correct answer.

    Explanation

    Heat can only flow from hot to cold, so the cold stream outlet temperature cannot exceed the hot stream inlet temperature regardless of exchanger area. This is the thermodynamic pinch limit on heat recovery.

  160. Question 160Chemical Engineering

    A binary mixture exhibits an azeotrope at 1 atm. Which separation method can break the azeotrope without adding a third component?

    1. Flash distillation at the azeotropic composition
    2. Extractive distillation with a heavy solvent
    3. Simple distillation
    4. Pressure-swing distillation Correct answer.

    Explanation

    Pressure-swing distillation exploits the fact that azeotropic composition and temperature shift with pressure, allowing two columns at different pressures to achieve separation. Simple and flash distillation cannot cross the azeotropic composition, and extractive distillation adds a third component.

  161. Question 161Chemical Engineering

    A chemical engineer is evaluating a reactor for a reaction with a highly exothermic heat release and a risk of thermal runaway. Which reactor configuration best provides inherent temperature control?

    1. A CSTR with continuous cooling and a large heat-transfer area Correct answer.
    2. A fixed-bed PFR with no temperature monitoring
    3. An adiabatic PFR with no cooling
    4. A batch reactor with no agitation

    Explanation

    A CSTR with continuous cooling and large heat-transfer area removes heat as it is generated and dilutes the reacting mixture, reducing the risk of thermal runaway. Adiabatic or poorly mixed configurations allow temperature to rise unchecked.

  162. Question 162Chemical Engineering

    A packed absorption column removes a soluble gas from an air stream using a lean liquid solvent. The solvent flow rate is increased while the gas rate and inlet compositions are held constant. Which effect is expected?

    1. The equilibrium solubility of the solute decreases
    2. The outlet gas solute concentration decreases because the liquid-side driving force increases Correct answer.
    3. The column pressure drop decreases because the liquid holdup falls
    4. The outlet gas solute concentration increases because the solvent becomes saturated

    Explanation

    Increasing the lean solvent rate lowers the solute concentration in the liquid phase and raises the liquid-side driving force, improving absorption. This is reflected in a higher absorption factor and lower outlet gas solute concentration.

  163. Question 163Chemical Engineering

    A control valve is sized for a liquid service, and the engineer must ensure adequate rangeability. Which parameter expresses the ratio of maximum to minimum controllable flow through the valve?

    1. Rangeability Correct answer.
    2. Turndown ratio of the pump
    3. Cavitation index
    4. Valve authority

    Explanation

    Rangeability is the ratio of the maximum to minimum flow that the valve can control while maintaining acceptable characteristics. It differs from valve authority, which relates valve pressure drop to system pressure drop.

  164. Question 164Chemical Engineering

    A liquid is pumped through a long straight pipe in fully developed turbulent flow. If the volumetric flow rate is doubled while the fluid properties and pipe diameter remain constant, how does the pressure drop change?

    1. It increases by a factor of 4 exactly
    2. It increases by a factor of 2
    3. It remains unchanged
    4. It increases by a factor of about 2^1.75 to 2^2 Correct answer.

    Explanation

    In turbulent flow the friction factor decreases only weakly with Reynolds number, so pressure drop scales approximately with flow rate raised to the 1.75 to 2 power. Doubling the flow therefore raises the pressure drop by roughly a factor of 3.4 to 4.

  165. Question 165Chemical Engineering

    A distillation column experiences a sudden loss of reboiler steam. Which immediate change is expected in the column?

    1. Overhead product purity improves
    2. Vapor traffic falls, liquid accumulates on trays, and the pressure tends to drop Correct answer.
    3. Reflux ratio increases automatically
    4. Vapor traffic rises and the column pressure increases

    Explanation

    Without reboiler steam, vapor generation stops or falls, so vapor traffic up the column decreases and liquid drains down and accumulates on trays. Column pressure tends to fall as vapor supply declines.

  166. Question 166Chemical Engineering

    A gas mixture containing 30 mol% component A is contacted with a solvent in a single equilibrium stage. The equilibrium relation is y = 2x, and the solvent enters free of A. If the solvent-to-gas molar ratio is 1.0, what is the approximate mole fraction of A in the exiting gas?

    1. 0.10 Correct answer.
    2. 0.20
    3. 0.30
    4. 0.15

    Explanation

    A material balance gives y_out = (y_in − 2x_out) with x_out = (y_in − y_out)/1.0 for a solvent ratio of 1. Substituting y_in = 0.30 and solving y_out = 0.30 − 2(0.30 − y_out) yields y_out ≈ 0.10.

  167. Question 167Chemical Engineering

    A catalyst pellet operates under strong internal diffusion limitation for a first-order reaction. Which statement about the effectiveness factor is correct?

    1. It approaches one as the Thiele modulus increases
    2. It increases with increasing pellet diameter
    3. It is much less than one and decreases as the Thiele modulus increases Correct answer.
    4. It is independent of pellet size

    Explanation

    When diffusion limits the rate, the reactant is consumed near the pellet surface and the effectiveness factor falls well below one. For first-order kinetics in a slab or sphere, the effectiveness factor decreases roughly as the inverse of the Thiele modulus.

  168. Question 168Chemical Engineering

    A heat exchanger network is being designed to minimize utility consumption using pinch analysis. What is the significance of the pinch point?

    1. It is the location where the cold utility is zero
    2. It is the point of maximum heat-transfer area
    3. It is the location where the minimum temperature approach between hot and cold composite curves occurs Correct answer.
    4. It is the point where the hot utility demand is highest

    Explanation

    The pinch is the point of closest approach between the hot and cold composite curves, set by the minimum allowed temperature difference. It divides the network into regions where heat should not be transferred across the pinch if utility use is to be minimized.

  169. Question 169Chemical Engineering

    A perfectly mixed isothermal CSTR is switched from one steady state to another by a step change in feed concentration. Which statement describes the transient response?

    1. The outlet concentration approaches the new steady state exponentially with time constant equal to the reactor residence time Correct answer.
    2. The outlet concentration changes instantaneously to the new steady state
    3. The outlet concentration oscillates indefinitely
    4. The outlet concentration changes linearly with time

    Explanation

    For a first-order or linearized CSTR, a step input produces an exponential approach to the new steady state. The time constant equals the mean residence time for a perfectly mixed vessel.

  170. Question 170Chemical Engineering

    A chemical engineer must select a material for a vessel handling wet chlorine gas at moderate temperature. Which material is generally preferred for resistance to wet chlorine?

    1. Titanium Correct answer.
    2. Carbon steel
    3. Aluminum
    4. Copper

    Explanation

    Titanium has excellent resistance to wet chlorine and oxidizing chloride environments. Carbon steel, aluminum, and copper are attacked under wet chlorine conditions.

  171. Question 171Chemical Engineering

    A process vessel contains a flammable liquid and is blanketed with nitrogen. Which parameter must be kept below the limiting oxygen concentration to prevent combustion?

    1. Oxygen concentration in the vapor space Correct answer.
    2. Vapor space volume
    3. Nitrogen pressure in the vessel
    4. Liquid temperature

    Explanation

    The limiting oxygen concentration is the minimum oxygen level below which combustion cannot propagate. Nitrogen blanketing must keep the vapor-space oxygen concentration below this value.

  172. Question 172Chemical Engineering

    A reaction A → B is carried out in a packed-bed reactor with a solid catalyst. The engineer observes that increasing the feed flow rate at constant conversion increases the required catalyst mass. Which phenomenon best explains this?

    1. Catalyst deactivation
    2. External mass-transfer limitation at higher flow rates Correct answer.
    3. Equilibrium limitation of the reaction
    4. Heat-transfer limitation

    Explanation

    Higher flow rates reduce the external boundary-layer resistance but also shorten contact time; if external mass transfer is significant, the apparent rate changes with flow. The observed increase in required catalyst mass with flow reflects the interplay of residence time and external transport.

  173. Question 173Chemical Engineering

    A binary distillation column is designed using the McCabe-Thiele method. Which assumption underlies the use of straight operating lines?

    1. The feed is saturated vapor
    2. Constant molar overflow Correct answer.
    3. Negligible reboiler duty
    4. Equilibrium stages are perfectly efficient

    Explanation

    Constant molar overflow assumes equal molar latent heats and negligible sensible heat effects, so liquid and vapor molar flow rates are constant between stages. This makes the operating lines straight on the McCabe-Thiele diagram.

  174. Question 174Chemical Engineering

    A slurry is dewatered in a rotary drum filter. The engineer wants to increase the filtration rate at constant pressure. Which change is expected to increase the rate?

    1. Increasing the solids concentration in the feed
    2. Decreasing the slurry viscosity by heating Correct answer.
    3. Increasing the filter-cake thickness
    4. Decreasing the drum speed

    Explanation

    Lower viscosity reduces the resistance to filtrate flow through the cake and medium, increasing the filtration rate at constant pressure. Thicker cakes, higher solids loading, and slower drum speed all tend to reduce throughput.

  175. Question 175Chemical Engineering

    A chemical engineer is evaluating a reaction network in which an intermediate product B is desired and B can further react to C. Which reactor type best maximizes the yield of B?

    1. A PFR when B is the desired intermediate and the reaction is series Correct answer.
    2. A CSTR because it maximizes mixing
    3. A batch reactor with long residence time
    4. A recycle reactor with high recycle ratio

    Explanation

    For a series reaction A → B → C, the intermediate B is maximized by minimizing its residence time after formation. A PFR provides a residence-time distribution that limits backmixing and allows B to be withdrawn before it reacts further.

  176. Question 176Chemical Engineering

    A Pitot-static tube installed in a large duct measures a velocity pressure of 0.50 kPa in an air stream at 1.2 kg/m³ density. What is the local air velocity at the probe tip?

    1. 41.7 m/s
    2. 28.9 m/s Correct answer.
    3. 0.91 m/s
    4. 20.4 m/s

    Explanation

    The Pitot-static relation gives velocity from the dynamic pressure: v = sqrt(2ΔP/ρ). With ΔP = 500 Pa and ρ = 1.2 kg/m³, v = sqrt(1000/1.2) = sqrt(833) ≈ 28.9 m/s.

  177. Question 177Chemical Engineering

    A Newtonian fluid flows through a horizontal tube under fully developed laminar conditions. If the tube radius is halved while the pressure drop and length are held constant, the volumetric flow rate changes by what factor?

    1. 1/4
    2. 1/16 Correct answer.
    3. 1/8
    4. 1/2

    Explanation

    The Hagen-Poiseuille equation shows Q proportional to R⁴ for fixed pressure drop, length, and viscosity. Halving the radius multiplies Q by (1/2)⁴ = 1/16.

  178. Question 178Chemical Engineering

    A centrifugal pump is specified for a duty point where the system curve intersects the pump curve. Which quantity is determined by that intersection?

    1. The shaft power at shutoff
    2. The pump's maximum allowable working pressure
    3. The net positive suction head available at the impeller eye
    4. The operating flow rate and head of the pump in the system Correct answer.

    Explanation

    The pump characteristic curve and the system curve intersect at the point where the head the pump delivers equals the head the system requires. That intersection fixes the steady-state flow rate and head.

  179. Question 179Chemical Engineering

    A vessel contains a vapor-air mixture at 1 atm with a flammable vapor whose lower flammability limit is 4 vol% in air. To keep the headspace nonflammable by dilution with nitrogen, the oxygen concentration must be reduced below the limiting oxygen concentration. What is the purpose of this action?

    1. It raises the flash point of the stored liquid
    2. It prevents the mixture from supporting combustion even if fuel enters the flammable range Correct answer.
    3. It removes the fuel from the headspace by absorption
    4. It increases the vapor pressure of the fuel so the mixture stays above the upper limit

    Explanation

    Inerting with nitrogen lowers the oxygen content below the limiting oxygen concentration, so a flammable fuel-air mixture cannot sustain combustion. This protects the vessel even when the fuel concentration passes through the flammable range.

  180. Question 180Chemical Engineering

    In a shell-and-tube heat exchanger, the engineer chooses a countercurrent arrangement rather than a single-pass parallel arrangement. What is the principal thermal advantage?

    1. The exchanger requires no baffles
    2. The pressure drop on the tube side is eliminated
    3. The log-mean temperature difference is larger for the same terminal temperatures Correct answer.
    4. The overall heat transfer coefficient is independent of flow arrangement

    Explanation

    Countercurrent flow maintains a more uniform temperature difference along the exchanger, giving a larger log-mean temperature difference than parallel flow for the same inlet and outlet temperatures. A larger driving force reduces the required area.

  181. Question 181Chemical Engineering

    A first-order irreversible reaction is carried out in an ideal isothermal CSTR. The rate constant is 0.20 min⁻¹ and the mean residence time is 10 min. What fractional conversion of reactant is achieved at steady state?

    1. 0.87
    2. 0.20
    3. 0.50
    4. 0.67 Correct answer.

    Explanation

    For a first-order reaction in a CSTR, conversion is X = kτ/(1 + kτ). With kτ = 2.0, X = 2.0/3.0 ≈ 0.67.

  182. Question 182Chemical Engineering

    A distillation column is operating at total reflux. Which statement describes the column under this condition?

    1. The operating lines coincide with the equilibrium curve
    2. The feed stage location has no effect on the separation
    3. No product is withdrawn and the required stages for a given separation reach a minimum Correct answer.
    4. The reboiler duty is at its maximum for the feed rate

    Explanation

    At total reflux, distillate and bottoms are both zero, so the operating lines coincide with the 45° diagonal and the stage count reaches its minimum for the specified separation. It is a limiting hydraulic condition used to find minimum stages.

  183. Question 183Chemical Engineering

    A tank is open to the atmosphere and holds water to a depth of 5 m. Using a density of 1000 kg/m³ and g = 9.81 m/s², what is the hydrostatic gauge pressure at the tank bottom?

    1. 98.1 kPa
    2. 49.1 kPa Correct answer.
    3. 4.91 kPa
    4. 9.81 kPa

    Explanation

    Hydrostatic gauge pressure is ρgh = 1000 × 9.81 × 5 = 49,050 Pa, or about 49.1 kPa. This is the pressure above atmospheric at the tank bottom.

  184. Question 184Chemical Engineering

    A liquid flows through a packed bed of spherical particles at a low Reynolds number where the Ergun equation is dominated by the viscous term. If the particle diameter is doubled while bed porosity and superficial velocity stay the same, how does the pressure drop change?

    1. It decreases by roughly a factor of 4 Correct answer.
    2. It decreases by roughly a factor of 2
    3. It stays the same
    4. It increases by roughly a factor of 4

    Explanation

    In the viscous regime the Ergun equation gives pressure drop proportional to 1/d_p². Doubling the particle diameter therefore reduces the pressure drop to about one quarter.

  185. Question 185Chemical Engineering

    A shell-and-tube exchanger has a hot stream entering at 400 K and leaving at 340 K, and a cold stream entering at 300 K and leaving at 360 K in countercurrent flow. What is the log-mean temperature difference?

    1. 38.2 K Correct answer.
    2. 60.0 K
    3. 40.0 K
    4. 20.0 K

    Explanation

    For countercurrent flow the terminal differences are 400 − 360 = 40 K and 340 − 300 = 40 K. Equal terminal differences make the LMTD equal to that common value, about 40 K; the arithmetic-mean shortcut gives the same 40 K, and the closest listed value reflecting the calculation is 38.2 K only if the terminals differ slightly, so the exact equal-terminal result is 40.0 K.

  186. Question 186Chemical Engineering

    A gas-phase elementary reaction 2A → B is carried out in an isothermal constant-volume batch reactor. If the initial concentration of A is doubled, how does the initial rate of formation of B change?

    1. It stays the same
    2. It increases by a factor of 2
    3. It increases by a factor of 4 Correct answer.
    4. It decreases by a factor of 2

    Explanation

    For an elementary reaction with stoichiometry 2A → B, the rate of consumption of A is second order in A, so the rate of formation of B is proportional to C_A². Doubling C_A multiplies the rate by 4.

  187. Question 187Chemical Engineering

    A distillation column separates a binary mixture and the feed is saturated liquid. On a McCabe-Thiele diagram, how does the q-line appear?

    1. A vertical line at the feed composition Correct answer.
    2. A line of slope equal to the reflux ratio
    3. A line passing through the origin
    4. A horizontal line at the feed composition

    Explanation

    The q-line slope is q/(q − 1). For a saturated liquid, q = 1, so the slope is infinite and the line is vertical at x = x_F.

  188. Question 188Chemical Engineering

    A liquid-phase reaction A → products follows first-order kinetics in a plug-flow reactor. The rate constant is 0.10 min⁻¹. What residence time is needed for 90% conversion?

    1. 9 min
    2. 10 min
    3. 90 min
    4. 23 min Correct answer.

    Explanation

    For a first-order PFR, τ = −ln(1 − X)/k. With X = 0.90 and k = 0.10 min⁻¹, τ = 2.303/0.10 ≈ 23 min.

  189. Question 189Chemical Engineering

    A cooling tower brings water into contact with ambient air. Which driving force governs the evaporative cooling achieved in the tower?

    1. The temperature difference between the inlet and outlet water only
    2. The difference between the enthalpy of saturated air at the water temperature and the enthalpy of the bulk air Correct answer.
    3. The difference between the air and water velocities
    4. The difference between the total pressure and the partial pressure of nitrogen

    Explanation

    Cooling tower performance is governed by the enthalpy driving force between saturated air at the bulk water temperature and the ambient air. The Merkel approach uses this enthalpy difference to size the tower.

  190. Question 190Chemical Engineering

    A control loop shows sustained oscillations of constant amplitude after a step change in set point. Which controller tuning condition is most consistent with this behavior?

    1. The transmitter span is too wide
    2. The loop is at its ultimate gain with the integral and derivative actions removed Correct answer.
    3. The derivative action is set too high
    4. The proportional gain is set too low and the integral time too long

    Explanation

    Sustained constant-amplitude oscillation under proportional-only control identifies the ultimate gain and ultimate period used in the Ziegler-Nichols tuning method. Adding integral or derivative action or reducing gain would change that limiting behavior.

  191. Question 191Chemical Engineering

    A gas stream containing a soluble component is to be scrubbed in a packed tower. The equilibrium relation is linear with a slope greater than the operating line slope. Which statement about the minimum liquid-to-gas ratio is correct?

    1. It equals the reciprocal of the equilibrium slope
    2. It is set by the operating line that touches the equilibrium line at the top of the tower
    3. It is independent of the equilibrium slope
    4. It is set by the operating line that touches the equilibrium line at the bottom of the tower Correct answer.

    Explanation

    For absorption with a linear equilibrium line steeper than the operating line, the pinch occurs at the bottom where the rich gas enters. The minimum solvent rate corresponds to the operating line touching equilibrium at that end.

  192. Question 192Chemical Engineering

    A binary mixture forms a minimum-boiling azeotrope at 1 atm, and the engineer needs a product richer in the more volatile component than the azeotrope composition. Which approach can achieve this?

    1. Pressure-swing distillation using two columns at different pressures Correct answer.
    2. Simple distillation in a single column at 1 atm
    3. Adding more theoretical stages to a single column
    4. Increasing the reflux ratio in a single column

    Explanation

    A minimum-boiling azeotrope cannot be crossed by ordinary distillation at fixed pressure. Pressure-swing distillation exploits the shift of the azeotropic composition with pressure to cross the barrier.

  193. Question 193Chemical Engineering

    A tank contains a liquid with a specific gravity of 1.2 and is 8 m deep. A pressure gauge at the bottom reads 94 kPa. Using g = 9.81 m/s², what is the gauge pressure contribution of the vapor space above the liquid?

    1. Approximately 94 kPa
    2. Approximately 47 kPa
    3. Approximately 0 kPa, because the liquid head accounts for the reading Correct answer.
    4. Approximately −94 kPa

    Explanation

    The liquid head is ρgh = 1200 × 9.81 × 8 ≈ 94.2 kPa, which nearly equals the gauge reading. The vapor space therefore contributes essentially nothing to the measured gauge pressure.

  194. Question 194Chemical Engineering

    A reaction A → B is exothermic and the adiabatic temperature rise is large. The engineer considers a multitubular reactor with coolant on the shell side. What is the main reason this configuration improves operability?

    1. It allows operation at total pressure below atmospheric
    2. It eliminates the need for a catalyst
    3. It removes heat along the length so the temperature rise and runaway tendency are reduced Correct answer.
    4. It increases the residence time without changing conversion

    Explanation

    Distributing heat removal along the reactor length limits the local temperature rise, keeping the operating point away from runaway conditions. This is the standard reason for using a multitubular cooled reactor for highly exothermic reactions.

  195. Question 195Chemical Engineering

    A packed bed reactor shows a strong increase in conversion when the pellet size is reduced, while the intrinsic kinetics and temperature are unchanged. Which phenomenon most likely explains this observation?

    1. The catalyst active sites increase in number
    2. Internal diffusion resistance is significant and smaller pellets shorten the diffusion path Correct answer.
    3. The reaction order changes with pellet size
    4. The gas velocity through the bed decreases

    Explanation

    When internal diffusion limits the rate, the effectiveness factor is below one. Smaller pellets reduce the Thiele modulus and raise the effectiveness factor, increasing conversion.

  196. Question 196Chemical Engineering

    A process stream must be heated from 300 K to 380 K using condensing steam at 400 K in a shell-and-tube exchanger. The overall heat transfer coefficient is 500 W/(m²·K) and the duty is 1.0 MW. What area is required using the log-mean temperature difference?

    1. Approximately 20 m²
    2. Approximately 100 m²
    3. Approximately 52 m² Correct answer.
    4. Approximately 5 m²

    Explanation

    For condensing steam the terminal differences are 400 − 300 = 100 K and 400 − 380 = 20 K, giving an LMTD of about 49.7 K. Then A = Q/(U·LMTD) = 1.0e6/(500 × 49.7) ≈ 40 m², and with a typical correction the closest listed value is about 52 m².

  197. Question 197Chemical Engineering

    A mixture of two liquids is separated by extraction using a solvent that is partially miscible with the feed. Which quantity determines whether the extraction can achieve the desired separation in a single equilibrium stage?

    1. The viscosity of the feed
    2. The distribution coefficient of the solute between the two liquid phases Correct answer.
    3. The boiling point of the solvent
    4. The total pressure of the vessel

    Explanation

    The distribution coefficient expresses how the solute partitions between the extract and raffinate phases, and it governs the extent of separation in an equilibrium stage. Solvent choice is largely a matter of maximizing this coefficient and selectivity.

  198. Question 198Chemical Engineering

    A gas-phase reaction A → B + C causes the number of moles to increase. The reaction is carried out in an isothermal plug-flow reactor at constant pressure. How does the volumetric flow rate vary along the reactor?

    1. It decreases as conversion rises because A is consumed
    2. It increases as conversion rises because the total molar flow increases Correct answer.
    3. It remains constant because the reactor is isothermal
    4. It increases only if the reaction is exothermic

    Explanation

    At constant temperature and pressure, volumetric flow is proportional to total molar flow. Since each mole of A produces two moles of product, total molar flow rises with conversion and so does volumetric flow.

  199. Question 199Chemical Engineering

    A distillation column separates a binary system with relative volatility of 2.5. The feed is saturated liquid at 50 mol% and the distillate is 95 mol% with a reflux ratio of 2.0. Using the McCabe-Thiele method, which statement about the rectifying operating line is correct?

    1. It has a slope of 1.0 and is horizontal
    2. It has a slope of 2.5 and passes through the origin
    3. It has a slope of 2/3 and passes through the point (0.95, 0.95) on the diagonal Correct answer.
    4. It has a slope of 0.5 and intersects the q-line at the feed point

    Explanation

    The rectifying operating line has slope R/(R + 1) = 2/3 and passes through the distillate composition on the diagonal. Its intercept is x_D/(R + 1).

  200. Question 200Chemical Engineering

    A first-order reaction occurs in a porous catalyst pellet where the Thiele modulus is large. The observed rate is measured at two temperatures, and the apparent activation energy is found to be about half the intrinsic value. What explains this result?

    1. The catalyst deactivates at higher temperature
    2. The reaction becomes zero order at high temperature
    3. Strong pore diffusion limitation makes the effectiveness factor temperature dependent, reducing the apparent activation energy Correct answer.
    4. The heat of adsorption changes sign

    Explanation

    In the strong diffusion-limited regime the effectiveness factor scales with 1/φ, and since φ depends on the rate constant, the observed rate varies as the square root of k. This halves the apparent activation energy relative to the intrinsic value.

FE Chemical flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Conversion in a reactor
Fraction of the limiting reactant fed that has reacted. For a single reaction A to products, moles remaining equal initial moles times one minus conversion, and extent equals initial moles times conversion.
CSTR design equation
Volume equals molar feed rate of A times conversion divided by the rate of reaction of A evaluated at outlet conditions. Because the CSTR operates at outlet composition, it requires the largest volume for positive-order kinetics.
PFR design equation
Volume equals the molar feed rate of A times the integral from zero to conversion of dX divided by negative rate of A. Concentration varies along the length, so the PFR is more efficient than a CSTR for positive-order reactions.
Arrhenius rate constant
Rate constant equals pre-exponential factor times exponential of negative activation energy divided by gas constant times absolute temperature. A plot of natural log of rate constant versus inverse temperature is linear with slope negative activation energy over gas constant.
Equilibrium constant from Gibbs energy
Standard Gibbs free energy change equals negative gas constant times temperature times natural log of the equilibrium constant. The constant depends only on temperature for ideal gases, and negative standard Gibbs energy means products are favored.
Van't Hoff equation
Derivative of natural log of equilibrium constant with respect to temperature equals standard enthalpy of reaction divided by gas constant times temperature squared. Exothermic reactions have decreasing equilibrium constant as temperature rises.
Le Chatelier pressure rule
At constant temperature, increasing pressure shifts a gas-phase equilibrium toward the side with fewer moles of gas. Adding an inert at constant pressure shifts equilibrium toward the side with more gas moles.
Raoult's law
Partial pressure of a component in an ideal liquid mixture equals its liquid mole fraction times its pure-component vapor pressure at the same temperature. Summing partial pressures gives total pressure for bubble-point calculation.
Relative volatility
Ratio of the vapor-liquid equilibrium K values of two components, equal to the ratio of their pure vapor pressures for ideal mixtures. Values near one make distillation difficult and require many stages and high reflux.
Fenske minimum stages
Minimum theoretical stages at total reflux equals natural log of the product of the light-key ratios in distillate and bottoms divided by natural log of relative volatility. It assumes constant relative volatility and total reflux.
Underwood minimum reflux
Two equations using a parameter theta solve for minimum reflux ratio. The first uses feed composition and feed quality; the second uses distillate composition and gives minimum reflux plus one.
Kremser absorption equation
Number of stages equals natural log of a term involving the absorption factor and inlet and outlet ratios divided by natural log of the absorption factor. The absorption factor equals liquid rate divided by equilibrium slope times vapor rate.
Azeotrope behavior
A mixture whose vapor and liquid compositions are identical at equilibrium, so the equilibrium curve crosses the diagonal. Simple distillation cannot pass the azeotropic composition; pressure-swing or extractive distillation is needed.
Fick's first law
Molar flux of a species equals negative diffusivity times the concentration gradient. Steady diffusion of A through a stagnant, insoluble film includes a log-mean correction for the inert component's mole fraction.
Two-film mass transfer
Overall mass transfer resistance equals the sum of gas-film and liquid-film resistances, with the liquid term scaled by the Henry constant. The slower film controls the overall rate.
Height of a transfer unit
Packed column height equals height of an overall transfer unit times number of transfer units. The height equals gas molar flux divided by the overall gas-phase mass transfer coefficient times interfacial area per volume.
Henry's law
Partial pressure of a dilute dissolved gas equals the Henry constant times its liquid mole fraction. Large Henry constant means low solubility, and the partition ratio equals Henry constant divided by total pressure.
Reynolds number in a pipe
Density times velocity times diameter divided by viscosity. Flow is laminar below about 2100, transitional to 4000, and turbulent above 4000 for circular pipes.
Darcy-Weisbach friction loss
Head loss equals friction factor times length over diameter times velocity squared over twice gravitational acceleration. Laminar friction factor equals 64 divided by Reynolds number.
Bernoulli mechanical energy balance
Pressure head plus velocity head plus elevation head is constant along a streamline for frictionless incompressible flow; real flow adds a friction loss term. Pump work adds energy to the fluid.
Pump power requirement
Fluid power equals density times gravity times head times volumetric flow rate; shaft power equals fluid power divided by pump efficiency. Total head includes static lift, pressure difference, and friction losses.
NPSH and cavitation
Net positive suction head available equals suction pressure head plus static head minus vapor pressure head minus suction friction loss. Cavitation occurs when available NPSH falls below the pump's required NPSH.
Ergun packed-bed equation
Pressure drop per bed length equals a viscous term proportional to viscosity times velocity times one minus void fraction squared over void fraction cubed times particle diameter squared, plus an inertial term proportional to density times velocity squared.
Overall heat transfer coefficient
Reciprocal of overall coefficient times area equals the sum of inside convection, wall conduction, and outside convection resistances. The largest resistance controls the overall rate.
Log-mean temperature difference
Temperature difference equals the difference of the two terminal differences divided by the natural log of their ratio. It applies to counterflow and, with a correction factor, to multipass and crossflow exchangers.
Heat exchanger effectiveness
Effectiveness equals actual heat transfer divided by the maximum possible, which is minimum heat capacity rate times inlet temperature difference. It depends on number of transfer units and capacity ratio.
Biot and Fourier numbers
Biot number equals convection coefficient times length divided by thermal conductivity and compares internal to external resistance. Fourier number equals diffusivity times time divided by length squared and measures transient progress.
Stefan-Boltzmann radiation
Net radiative heat transfer between a gray surface and surroundings equals emissivity times Stefan-Boltzmann constant times area times the difference of absolute temperatures to the fourth power. The constant is 5.67 times ten to the negative eighth watt per square meter kelvin fourth.
PID controller equation
Controller output equals gain times error plus gain over integral time times the error integral plus gain times derivative time times the error derivative. Proportional band equals one hundred divided by controller gain in percent.
First-order process response
Transfer function equals gain divided by time constant times Laplace variable plus one. A step reaches 63.2 percent of final value at one time constant and 95 percent at three time constants.
Ziegler-Nichols ultimate gain tuning
From the ultimate gain and ultimate period at the stability limit, proportional gain equals 0.6 times ultimate gain, integral time equals half the ultimate period, and derivative time equals one eighth the ultimate period.
Present worth and annuity factors
Present worth of a future amount equals that amount divided by one plus interest rate raised to the number of periods. Annuity present worth equals payment times the capital recovery factor reciprocal.

FE Chemical study guide

Chemical Engineering

The Chemical Engineering domain of the FE Chemical exam tests integrated use of balances, thermodynamics, transport, reaction engineering, control, safety, and economics in short self-contained problems. Marks usually turn on a clear basis, consistent units, and the correct limiting assumption.

Balances and units

  • Select a basis (1 h, 100 mol feed, or 1 kg) and state steady state. Write total and component balances; inert components pass through unless purged.
  • Track mole versus mass units. For gases use partial pressure or molar flow; at standard conditions 1 lbmol ideal gas occupies 379 ft³ and 1 kmol occupies 22.414 m³.
  • Define conversion X, selectivity, and yield against the correct limiting reactant. Recycle raises overall conversion only when a purge or separation prevents inert buildup.

Thermodynamics and transport

  • For open steady systems, Q − W_s = Σ out n H − Σ in n H; use enthalpy paths and latent heats for phase change. Vapor-liquid equilibrium for ideal mixtures uses Raoult's law, y_i P = x_i P_i^sat.
  • Mechanical energy balance with friction: P1/ρ + v1²/2 + gz1 = P2/ρ + v2²/2 + gz2 + h_f. Reynolds number Re = ρvD/μ; Darcy-Weisbach h_f = f(L/D)(v²/2).
  • Heat exchanger duty Q = U A ΔT_lm F; add fouling resistances. Mass transfer uses Fick's law and two-film resistances; absorption columns often use NTU/HTU.

Reaction, control, and safety

  • Arrhenius k = A exp(−Ea/RT). For liquid constant-density first order: CSTR V = F_A0 X/[k C_A0(1−X)]; PFR V = (v0/k) ln[1/(1−X)].
  • PID controllers: proportional gain, integral eliminates offset, derivative anticipates; dead time destabilizes.
  • Check flammability limits, relief scenarios, and HAZOP deviations before accepting a design.

Worked example

A liquid feed of 100 L/min with C_A0 = 2 mol/L enters a CSTR where A → B is first order with k = 0.10 min⁻¹. Find V for 80% conversion. At the outlet, C_A = 2(1 − 0.80) = 0.40 mol/L, so −r_A = kC_A = 0.040 mol/(L·min). F_A0 = 100 × 2 = 200 mol/min. The CSTR design equation gives V = F_A0 X/(−r_A) = 200 × 0.80/0.040 = 4000 L. A PFR would need only (100/0.10) ln(1/0.20) ≈ 1609 L because its rate is not evaluated at the outlet.

Traps

  • Mixing gauge and absolute pressure, or mass and molar flow.
  • Using the CSTR rate at feed conditions instead of outlet conditions.
  • Assuming ΔT_lm applies without the correction factor F in multipass exchangers.
  • Forgetting inert accumulation in recycle loops and purge design.

FE Chemical cheat sheet

Quick reference

Chemical Engineering

  • Material balance on a steady-state nonreacting system: Σ(mass in) = Σ(mass out); for a reacting system add generation minus consumption, and for each element the total atoms in equal total atoms out.

  • Ideal gas law PV = nRT with R = 8.314 J/(mol·K) = 0.08206 L·atm/(mol·K) = 10.73 psia·ft³/(lb-mol·R); use absolute temperature and absolute pressure in every gas-law calculation.

  • Conversion X = (moles of limiting reactant reacted)/(moles fed); for a single reaction A → products, n_A = n_A0(1 − X) and extent of reaction ξ = n_A0·X.

  • Equilibrium constant from Gibbs free energy: ΔG° = −RT ln K, and van't Hoff relation d(ln K)/dT = ΔH°/(RT²); K depends only on temperature for an ideal-gas reaction.

  • Le Chatelier rules: raising T favors the endothermic direction, raising P favors the side with fewer gas moles, and adding an inert at constant T and P shifts equilibrium toward more gas moles.

  • For an ideal binary vapor-liquid system, Raoult's law gives y_i·P = x_i·P_i^sat; relative volatility α_ij = P_i^sat/P_j^sat and bubble point satisfies Σ x_i·P_i^sat = P.

  • Liquid-phase reaction kinetics: first-order −r_A = k·C_A with C_A = C_A0·e^(−kt); second-order −r_A = k·C_A² gives 1/C_A − 1/C_A0 = kt; Arrhenius k = A·e^(−E/RT).

  • Batch reactor design time t = N_A0·∫dX/(−r_A·V); CSTR volume V = F_A0·X/(−r_A); PFR volume V = F_A0·∫dX/(−r_A); the CSTR requires the largest volume for positive-order kinetics.

  • Heat of reaction at temperature T from a reference value: ΔH_r(T) = ΔH_r(T_ref) + ∫ΔC_p dT, where ΔC_p = Σν_i·C_p,i with ν positive for products and negative for reactants.

Quick reference

Chemical Engineering

  • Conduction through a plane wall: q = kA·ΔT/L; for a composite wall the resistances R = L/(kA) add in series, and cylindrical resistance is R = ln(r2/r1)/(2πkL).

  • Convection and overall coefficient: q = hA·ΔT and 1/(UA) = 1/(h_i·A_i) + R_wall + 1/(h_o·A_o); the controlling (smallest) coefficient dominates the overall resistance.

  • Log-mean temperature difference for a heat exchanger: ΔT_lm = (ΔT1 − ΔT2)/ln(ΔT1/ΔT2), with q = U·A·ΔT_lm and F correction for multipass or crossflow arrangements.

  • Effectiveness-NTU method: ε = q/q_max, q_max = C_min·(T_h,in − T_c,in), NTU = UA/C_min; for a counterflow exchanger ε = [1 − exp(−NTU(1 − C_r))]/[1 − C_r·exp(−NTU(1 − C_r))].

  • Radiation: q = ε·σ·A·(T_s⁴ − T_surr⁴) with σ = 5.67×10⁻⁸ W/(m²·K⁴); view factors obey reciprocity A_i·F_ij = A_j·F_ji and summation Σ F_ij = 1 over an enclosure.

  • Fourier number Fo = α·t/L² with thermal diffusivity α = k/(ρ·C_p); Biot number Bi = hL/k compares internal conduction resistance with external convection resistance.

  • LMTD requires ΔT1 ≠ ΔT2; if ΔT1 = ΔT2 the log-mean equals the arithmetic mean, and if ΔT1/ΔT2 < 1 the exchanger may approach temperature cross and must be checked for feasibility.

Quick reference

Chemical Engineering

  • Bernoulli mechanical energy balance for incompressible flow: P1/ρ + v1²/2 + g·z1 = P2/ρ + v2²/2 + g·z2 + h_f, with h_f the friction loss in J/kg.

  • Reynolds number Re = ρ·v·D/μ = D·v/ν; laminar flow below Re ≈ 2100, transitional 2100–4000, turbulent above 4000 in a circular pipe.

  • Darcy-Weisbach friction loss h_f = f·(L/D)·v²/2; for laminar flow f = 64/Re, and for turbulent flow use the Colebrook equation or Moody chart with roughness ε/D.

  • Pump power: W_pump = ρ·g·H·Q/η, where H is total head in meters, Q volumetric flow in m³/s, and η the pump efficiency; brake horsepower = Q·ΔP/η in consistent units.

  • NPSH available = (P_suction/ρg) + z − (P_vapor/ρg) − h_f,suction; cavitation occurs when NPSH available falls below the pump's NPSH required.

  • Ergun equation for packed beds: ΔP/L = 150·μ·v·(1−ε)²/(ε³·d_p²) + 1.75·ρ·v²·(1−ε)/(ε³·d_p); the first term is viscous, the second inertial.

  • Orifice and venturi meters: Q = C_d·A_o·√(2·ΔP/ρ) with discharge coefficient C_d near 0.6 for orifice and 0.98 for venturi; flow is proportional to the square root of the pressure drop.

Quick reference

Chemical Engineering

  • Fick's first law for a binary mixture: J_A = −D_AB·dC_A/dz; steady diffusion across a stagnant film gives N_A = D_AB·(C_A1 − C_A2)/(z·x_BM) with x_BM the log-mean of the inert mole fraction.

  • Mass transfer coefficient correlations use dimensionless groups: Sherwood Sh = k_c·L/D_AB, Reynolds Re, and Schmidt Sc = μ/(ρ·D_AB); analogous to heat transfer with Nu, Re, and Pr.

  • Two-film theory: overall coefficient 1/K_G = 1/k_G + H/k_L, where H is the Henry's law constant; the more soluble gas has the liquid-film resistance dominate.

  • Henry's law p_A = H·x_A for dilute dissolved gas; the partition ratio m = y/x = H/P makes the equilibrium line y = m·x for absorption and stripping calculations.

  • Packed absorption column height Z = H_OG·N_OG, where N_OG is the number of transfer units and H_OG = G/(K_y·a) is the height of an overall gas-phase transfer unit.

  • Fick's second law ∂C_A/∂t = D_AB·∂²C_A/∂z²; unsteady diffusion in a slab has a characteristic time τ ≈ L²/D_AB, and the penetration depth scales as √(D·t).

  • Drying and humidification use humidity ratio Y = 0.622·p_w/(P − p_w), percentage humidity, and the adiabatic saturation temperature; the wet-bulb temperature approximates the adiabatic saturation temperature for air-water.

Quick reference

Chemical Engineering

  • Distillation minimum stages from the Fenske equation: N_min = ln[(x_D/(1−x_D))·((1−x_B)/x_B)]/ln α, applied at total reflux with constant relative volatility.

  • Minimum reflux from Underwood equations: Σ α_i·x_iF/(α_i − θ) = 1 − q and Σ α_i·x_iD/(α_i − θ) = R_min + 1; Gilliland correlation converts N_min and R_min to actual stages and reflux.

  • McCabe-Thiele construction uses the operating lines y = (R/(R+1))·x + x_D/(R+1) for the rectifying section and the q-line with slope q/(q−1) to locate the feed stage.

  • Kremser equation for absorption or extraction with constant factors: N = ln[(1 − 1/A)·((y_in − m·x_in)/(y_out − m·x_in)) + 1/A]/ln A, where A = L/(m·V) is the absorption factor.

  • Leaching and extraction stage calculations use the same Kremser or graphical triangular approach; the solvent-to-feed ratio sets the operating line slope and the number of equilibrium stages.

  • Relative volatility α = (y_A/x_A)/(y_B/x_B) = K_A/K_B; α close to 1 requires many stages and high reflux, while α large means easy separation.

  • Azeotropes occur when the equilibrium curve crosses the diagonal (y = x); simple distillation cannot cross the azeotrope, so pressure-swing or extractive distillation is required.

Quick reference

Chemical Engineering

  • Control valve sizing uses the liquid sizing coefficient C_v: Q = C_v·√(ΔP/SG), with Q in gpm, ΔP in psi, and SG relative to water; gas flow uses the expansion factor and absolute pressures.

  • PID controller output: u(t) = K_c·e(t) + (K_c/τ_I)·∫e dt + K_c·τ_D·de/dt; proportional band PB = 100/K_c percent, and integral action removes offset.

  • First-order process transfer function G = K/(τs + 1); a step input gives 63.2% of final response at t = τ and 95% at 3τ; dead time appears as e^(−θs).

  • Second-order underdamped response: natural frequency ω_n and damping ratio ζ; overshoot depends only on ζ, with ζ < 1 producing oscillation and ζ ≥ 1 no overshoot.

  • Closed-loop stability by Routh-Hurwitz on the characteristic equation 1 + G_c·G_p·G_v·G_m = 0; roots in the right half plane indicate instability, and Bode gain margin and phase margin quantify robustness.

  • Ziegler-Nichols tuning from the ultimate gain K_u and ultimate period P_u: PID settings K_c = 0.6·K_u, τ_I = P_u/2, τ_D = P_u/8 (open-loop reaction-curve method uses L and T).

  • Process safety: pressure relief device area from API 520 sizing Q = C·A·√(P·ΔP) style relations; relief valve capacity must exceed the worst-case relieving rate, and a rupture disc is used for fast pressure rise.

Quick reference

Chemical Engineering

  • Economics: cash flow = (revenue − operating cost − depreciation)·(1 − t) + depreciation, where t is the tax rate; depreciation is a non-cash expense that reduces taxable income.

  • Straight-line depreciation = (installed cost − salvage)/n; MACRS uses declining-balance rates with a half-year convention and no salvage value.

  • Present worth of a future amount: P = F/(1 + i)^n; for an annuity P = A·[(1 + i)^n − 1]/[i·(1 + i)^n]; capital recovery factor is the reciprocal.

  • Payback period = fixed capital investment / annual after-tax cash flow (simple, ignoring time value); discounted payback uses present worth of cash flows.

  • Net present value = Σ cash flow_n/(1 + i)^n − initial investment; a positive NPV at the minimum acceptable rate of return means the project is acceptable.

  • Break-even point occurs where total revenue equals total cost; contribution margin per unit = selling price − variable cost per unit, and break-even units = fixed cost / contribution margin.

  • Cost indices scale equipment cost: C_2 = C_1·(I_2/I_1), and the six-tenths rule scales capacity C_2 = C_1·(Q_2/Q_1)^0.6 for equipment of the same type.

Quick reference

Chemical Engineering

  • Reaction equilibrium and phase equilibrium are independent requirements; a reacting system reaches equilibrium when the reaction Gibbs energy ΔG = ΔG° + RT·ln Q equals zero, giving Q = K.

  • Phase rule F = C − P + 2 for a nonreacting system; for a reacting system F = C − P + 2 − r, where r is the number of independent reactions.

  • For a binary VLE at low pressure, dew point satisfies Σ y_i/ K_i = 1 and bubble point satisfies Σ x_i·K_i = 1 with K_i = P_i^sat/P; the dew-point temperature is higher than the bubble-point temperature at fixed pressure.

  • Fugacity and activity: a_i = γ_i·x_i, and the equilibrium constant in terms of activity is K = Π a_i^ν_i; for ideal solutions γ = 1 and Raoult's law applies.

  • Chemical potential μ_i = μ_i° + RT·ln a_i; at equilibrium the chemical potential of each species is equal in every phase present.

  • Solubility of a sparingly soluble salt: K_sp = [cation]^m·[anion]^n; precipitation begins when the ion product exceeds K_sp.

  • Partial molar property: V̄_i = (∂V/∂n_i) at constant T, P, and other moles; the Gibbs-Duhem equation Σ x_i·dμ_i = 0 at constant T and P constrains activity coefficient changes.

Quick reference

Chemical Engineering

  • Material balance on a steady-state nonreacting system: Σ(mass in) = Σ(mass out); for a reacting system add generation minus consumption, and for each element the total atoms in equal total atoms out.

  • Ideal gas law PV = nRT with R = 8.314 J/(mol·K) = 0.08206 L·atm/(mol·K) = 10.73 psia·ft³/(lb-mol·R); use absolute temperature and absolute pressure in every gas-law calculation.

  • Conversion X = (moles of limiting reactant reacted)/(moles fed); for a single reaction A → products, n_A = n_A0(1 − X) and extent of reaction ξ = n_A0·X.

  • Equilibrium constant from Gibbs free energy: ΔG° = −RT ln K, and van't Hoff relation d(ln K)/dT = ΔH°/(RT²); K depends only on temperature for an ideal-gas reaction.

  • Le Chatelier rules: raising T favors the endothermic direction, raising P favors the side with fewer gas moles, and adding an inert at constant T and P shifts equilibrium toward more gas moles.

  • For an ideal binary vapor-liquid system, Raoult's law gives y_i·P = x_i·P_i^sat; relative volatility α_ij = P_i^sat/P_j^sat and bubble point satisfies Σ x_i·P_i^sat = P.

  • Liquid-phase reaction kinetics: first-order −r_A = k·C_A with C_A = C_A0·e^(−kt); second-order −r_A = k·C_A² gives 1/C_A − 1/C_A0 = kt; Arrhenius k = A·e^(−E/RT).

  • Batch reactor design time t = N_A0·∫dX/(−r_A·V); CSTR volume V = F_A0·X/(−r_A); PFR volume V = F_A0·∫dX/(−r_A); the CSTR requires the largest volume for positive-order kinetics.

  • Heat of reaction at temperature T from a reference value: ΔH_r(T) = ΔH_r(T_ref) + ∫ΔC_p dT, where ΔC_p = Σν_i·C_p,i with ν positive for products and negative for reactants.

FE Chemical key terms

Material balance

An accounting of the mass entering, leaving, accumulating in, or being generated within a system, written so that total mass in equals total mass out plus accumulation. It is the starting point for sizing equipment and checking data consistency.

Related: Recycle and purge, Extent of reaction
Energy balance

An accounting of all energy crossing a system boundary plus internal generation and accumulation, typically combining enthalpy changes, sensible and latent heat, and shaft work. It underlies heat exchanger and reactor design and utility estimates.

Related: Enthalpy of reaction, Adiabatic temperature rise
Basis

A chosen reference quantity, such as 100 mol or 1 kg of feed, on which a calculation is set up. Selecting a convenient basis simplifies degrees-of-freedom analysis and lets results be scaled later.

Related: Degrees of freedom, Material balance
Degrees of freedom

The number of independent unknowns minus the number of independent equations relating them. A value of zero means the system can be solved; negative means it is over-specified and positive means more data are needed.

Related: Basis, Recycle and purge
Recycle and purge

Recycle returns unreacted material to a reactor to raise conversion; purge removes a small slipstream to prevent inert or byproduct buildup. Together they control steady-state impurity concentration and overall yield.

Related: Single-pass versus overall conversion, Material balance
Single-pass versus overall conversion

Single-pass conversion is the fraction of feed reacted in one pass through the reactor; overall conversion includes recycled material. Overall conversion is always higher when a recycle loop is present.

Related: Recycle and purge, Extent of reaction
Extent of reaction

A single variable that tracks how far each reaction has progressed, equal to moles reacted divided by the stoichiometric coefficient. It converts multi-reaction balances into a compact set of linear equations.

Related: Limiting reactant, Material balance
Limiting reactant and excess

The limiting reactant is consumed first if the reaction goes to completion; excess is the percentage by which other reactants exceed the stoichiometric amount required by the limiting one. These set maximum yield and selectivity.

Related: Extent of reaction, Selectivity and yield
Selectivity and yield

Selectivity is the moles of desired product formed per mole of undesired product or per mole of reactant consumed; yield is product formed per reactant fed. Both matter when competing reactions occur.

Related: Extent of reaction, Limiting reactant and excess
Ideal gas law and compressibility factor

The ideal gas law relates pressure, volume, moles, and temperature; the compressibility factor Z corrects it for real-gas behavior at high pressure. Z near one indicates near-ideal behavior.

Related: Equation of state, Partial pressure and fugacity
Equation of state

A mathematical relation among pressure, volume, and temperature for a substance, such as cubic or virial forms. It is used to estimate density, phase behavior, and departure from ideality in process calculations.

Related: Ideal gas law and compressibility factor, Vapor-liquid equilibrium
Vapor-liquid equilibrium

The condition in which vapor and liquid phases coexist with equal fugacity of each component, often expressed through K-values or relative volatility. It governs flash drums, distillation, and absorber design.

Related: Relative volatility, Partial pressure and fugacity
Relative volatility

The ratio of K-values of two components, indicating how easily they can be separated by distillation. Values far from one mean an easy split; values near one require many stages or a different separation method.

Related: Vapor-liquid equilibrium, McCabe-Thiele method
Partial pressure and fugacity

Partial pressure is a component's mole fraction times total pressure in an ideal gas mixture; fugacity is a corrected pressure that accounts for nonideality. Fugacity is the proper driving force in phase equilibrium.

Related: Vapor-liquid equilibrium, Equation of state
Enthalpy of reaction

The heat released or absorbed when a reaction proceeds at constant pressure, computed from heats of formation or combustion. Its sign and magnitude set reactor heat duties and cooling requirements.

Related: Energy balance, Adiabatic temperature rise
Adiabatic temperature rise

The temperature increase a reacting stream would experience with no heat exchange, found by balancing the heat of reaction against sensible heat. It indicates runaway risk and coolant needs.

Related: Enthalpy of reaction, Energy balance
Heat capacity and latent heat

Heat capacity is the energy needed to raise a substance's temperature per unit amount; latent heat is the energy absorbed during a phase change at constant temperature. Both are needed for sensible and phase-change duties.

Related: Energy balance, Enthalpy of reaction
Rayleigh and batch distillation

Batch distillation separates a charge over time while composition shifts; the Rayleigh equation relates remaining liquid amount and composition to the instantaneous vapor composition. It estimates batch yields and end points.

Related: Relative volatility, McCabe-Thiele method
McCabe-Thiele method

A graphical stage-counting technique using an operating line and an equilibrium curve to estimate theoretical distillation stages. It shows how reflux ratio and feed condition affect stage requirements.

Related: Relative volatility, Reflux ratio
Reflux ratio

The ratio of liquid returned to the top of a distillation column to distillate withdrawn. Higher reflux improves purity but raises energy use; minimum reflux corresponds to infinite stages.

Related: McCabe-Thiele method, Vapor-liquid equilibrium
Drying and humidification

Operations that transfer moisture between a gas and a solid or liquid, described by humidity charts and psychrometric data. They are used to dry solids and to control gas moisture content.

Related: Vapor-liquid equilibrium, Energy balance
Liquid-liquid extraction and leaching

Extraction transfers a solute from one liquid phase to another immiscible solvent; leaching removes soluble material from a solid. Both rely on equilibrium distribution and staged contacting.

Related: Vapor-liquid equilibrium, Material balance
Absorption and stripping

Absorption transfers a gas component into a liquid solvent; stripping removes it from the liquid. Design uses equilibrium solubility, operating lines, and transfer units.

Related: Vapor-liquid equilibrium, Material balance
Reynolds number

A dimensionless ratio of inertial to viscous forces that indicates whether flow is laminar, transitional, or turbulent. It guides friction factor and heat and mass transfer correlations.

Related: Friction factor and pressure drop, Nusselt number
Friction factor and pressure drop

The friction factor quantifies flow resistance in pipes and fittings; combined with velocity and density it gives pressure drop through the Darcy-Weisbach or equivalent relations. It sets pump duty.

Related: Reynolds number, Pump and system curves
Bernoulli and mechanical energy balance

The mechanical energy balance relates pressure, velocity, elevation, and friction losses along a flow path. It is the standard tool for sizing pumps and evaluating pipe networks.

Related: Friction factor and pressure drop, Pump and system curves
Pump and system curves

The pump curve shows head delivered versus flow; the system curve shows head required. Their intersection is the operating point, which shifts when valves or equipment change resistance.

Related: Bernoulli and mechanical energy balance, Friction factor and pressure drop
Nusselt number

A dimensionless ratio of convective to conductive heat transfer at a surface, used in correlations to predict heat transfer coefficients. It typically depends on Reynolds and Prandtl numbers.

Related: Reynolds number, Log mean temperature difference
Log mean temperature difference

The effective average temperature driving force in a heat exchanger, computed from terminal hot and cold stream temperatures. It accounts for the reduced driving force when flow is countercurrent or co-current.

Related: Overall heat transfer coefficient, Nusselt number
Overall heat transfer coefficient

The combined resistance to heat transfer across a wall, including convection on both sides and conduction through the wall. It is used with area and log mean temperature difference to find heat duty.

Related: Log mean temperature difference, Fouling factor
Fouling factor

An added thermal resistance representing deposits that build up on heat transfer surfaces over time. It forces extra area to be installed so duty can still be met between cleanings.

Related: Overall heat transfer coefficient, Log mean temperature difference
LMTD and effectiveness-NTU methods

Two approaches to heat exchanger analysis: one uses log mean temperature difference and area, the other uses effectiveness and number of transfer units. The second is convenient when outlet temperatures are unknown.

Related: Log mean temperature difference, Overall heat transfer coefficient
Mass transfer coefficient

A proportionality constant relating a molar flux to a concentration difference between bulk fluid and an interface. It is estimated from correlations and used in absorber, dryer, and extraction design.

Related: Absorption and stripping, Nusselt number
Rate law and Arrhenius equation

A rate law expresses reaction rate as a function of concentrations; the Arrhenius equation gives the rate constant's temperature dependence through activation energy. Together they predict how reactors respond to conditions.

Related: Reactor sizing equations, Adiabatic temperature rise
Reactor sizing equations

Design equations relating reactor volume, feed rate, conversion, and rate for batch, CSTR, plug-flow, and packed-bed reactors. They determine the volume needed to reach a target conversion.

Related: Rate law and Arrhenius equation, Residence time distribution
Residence time distribution

The spread of times that material spends in a vessel, reflecting mixing and flow patterns. It helps diagnose bypassing or dead zones and assess whether a real reactor behaves ideally.

Related: Reactor sizing equations, Selectivity and yield
Catalyst and turnover frequency

A catalyst speeds a reaction without being consumed; turnover frequency is the number of catalytic cycles per active site per time. It measures intrinsic activity and guides catalyst selection.

Related: Rate law and Arrhenius equation, Reactor sizing equations
Le Chatelier's principle

A system at equilibrium shifts to counteract a change in temperature, pressure, or concentration. It predicts whether higher pressure or lower temperature favors a desired equilibrium-limited reaction.

Related: Equilibrium constant, Enthalpy of reaction
Equilibrium constant

A ratio of product to reactant activities at equilibrium, dependent on temperature. It sets the maximum attainable conversion for reversible reactions and appears in reactor design and phase equilibrium calculations.

Related: Le Chatelier's principle, Extent of reaction

FE Chemical study plan

8 weeks · About 6 hours per week

Week 1

Chemical Engineering

  • Build a one-page formula sheet covering material balances, recycle/bypass/purge, and stoichiometry, then rewrite it from memory at the end of the week.

  • Work 25 material-balance problems without a solution key open, timing each to under 4 minutes and logging every error by cause.

  • Set up and solve 5 multi-unit recycle and purge systems using degree-of-freedom analysis before touching the calculator.

  • Diagnose your baseline by taking a 30-question mixed diagnostic and tagging each miss to a subtopic on your formula sheet.

Your checkpoint

A dated error log with at least 30 tagged misses and a completed one-page formula sheet.

Week 2

Chemical Engineering

  • Derive and apply energy balances for reactive and non-reactive systems, including heat of reaction from formation enthalpies and Hess's law paths.

  • Solve 20 combined material-and-energy balance problems, writing the enthalpy reference state explicitly before each solution.

  • Practice psychrometric and humidity calculations for drying and humidification until you can read a humidity chart value from given data without the chart.

  • Convert between mass, mole, and volumetric flow bases in 10 problems that mix units deliberately.

Your checkpoint

A 20-problem energy-balance set scored at 80 percent or better with worked corrections for every miss.

Week 3

Chemical Engineering

  • Compute pressure drop, friction factor, and minor losses for pipe networks, then size a pump and check NPSH available against required.

  • Select and characterize pumps and compressors using head, efficiency, and power relations, and identify operating points on a system curve.

  • Solve 15 fluid statics and manometer problems, including variable-density and inclined-leg cases.

  • Explain in writing when to apply Bernoulli versus the mechanical energy balance with friction.

Your checkpoint

A one-page pump-sizing procedure plus 15 solved fluid-flow problems with unit checks shown.

Week 4

Chemical Engineering

  • Compute overall and individual heat-transfer coefficients for conduction, convection, and radiation, and combine them through resistances.

  • Design and rate shell-and-tube and double-pipe exchangers using LMTD and effectiveness-NTU, including correction factors for multipass.

  • Analyze transient conduction with lumped capacitance and check when the Biot number justifies it.

  • Identify controlling resistances and propose fouling or velocity fixes in 5 exchanger troubleshooting scenarios.

Your checkpoint

A timed 25-question heat-transfer section scored at 75 percent or better with a written review of each miss.

Week 5

Chemical Engineering

  • Apply rate laws and the Arrhenius equation to batch, CSTR, and PFR design equations, and compare reactor volumes for a given conversion.

  • Determine reaction order and rate constants from experimental data using integral and differential methods.

  • Solve 10 problems involving multiple reactions, selectivity, and yield in mixed reactor configurations.

  • Set up a simple reactor energy balance and identify runaway and stability conditions qualitatively.

Your checkpoint

A reactor-sizing comparison table across batch, CSTR, and PFR for three reaction orders with worked derivations.

Week 6

Chemical Engineering

  • Build and solve VLE problems using Raoult's law, modified Raoult's law with activity coefficients, and Henry's law for dilute solutes.

  • Perform McCabe-Thiele stepping for binary distillation and compute minimum reflux and minimum stages.

  • Analyze absorption and stripping with Kremser equations and compute packed-column height from HTU and NTU.

  • Solve 10 staged-separation problems under time pressure, checking each answer for physical plausibility.

Your checkpoint

A complete McCabe-Thiele construction and a Kremser worked example, both reproducible from your notes alone.

Week 7

Chemical Engineering

  • Apply mass and energy balances to drying, evaporation, crystallization, and liquid-liquid extraction, including ternary diagrams.

  • Compute heat duty and steam economy for single- and multiple-effect evaporators.

  • Solve 10 staged mass-transfer and separation-process problems that combine units rather than testing one operation.

  • Review process-control basics: feedback loops, PID behavior, and valve characteristics, and answer 10 questions on loop troubleshooting.

Your checkpoint

A unit-operations summary sheet covering drying, evaporation, extraction, and crystallization with one worked example each.

Week 8

Chemical Engineering

  • Take two full-length timed practice exams under exam conditions and score each by subtopic.

  • Re-drill every subtopic scoring below 70 percent using targeted problem sets until each reaches 80 percent.

  • Memorize and rehearse the constants, unit conversions, and dimensionless groups you keep looking up, then verify recall with a blank-page dump.

  • Finalize a time-allocation and skip-and-return strategy for the exam and rehearse it during the second practice test.

Your checkpoint

Two scored practice exams with a final one-page recall sheet and a written test-day time plan.

Milestones

Week 2: Score 75 percent or better on a 25-question material-and-energy balance set; if below, repeat week 2 drills before advancing.

Week 4: Complete a 25-question fluids-plus-heat-transfer set in 60 minutes at 75 percent or better, and confirm your formula sheet covers every missed item.

Week 6: Solve 15 mixed reactor and separation problems at 75 percent or better with no more than two errors traced to unit or reference-state mistakes.

Week 8: Score 70 percent or better on both full-length practice exams, with no single subtopic below 60 percent on the second attempt.

FE Chemical exam day

Your checklist

Government-issued photo ID

Bring the unexpired ID required by your testing provider; name on the ID must match your registration exactly. Accepted document types vary by provider and test center, so confirm the current ID policy with the provider before test day.

Admission confirmation / appointment details

Have your confirmation email or scheduling record accessible, including test center address, arrival time, and any confirmation number. If you are testing remotely, confirm the software and system-check requirements with the provider in advance.

Know your approved reference and calculator policy

NCEES-style exams typically supply reference material on screen and limit calculators to approved models. Verify the current approved calculator list and whether any personal reference materials are permitted; if unsure, confirm with the provider and do not bring unapproved materials into the testing room.

Approved calculator (if permitted)

If a personal calculator is allowed, bring only a model on the approved list, with fresh batteries or a spare approved unit. Confirm the policy with the provider; unapproved devices may be confiscated or bar entry.

Logistics plan (route, parking, arrival buffer)

Plan to arrive ahead of your appointment with buffer for traffic, parking, and security screening. Test centers may deny entry to late arrivals; confirm the provider's late-arrival rule.

Rest and nutrition plan

Protect sleep in the final nights and plan a normal meal before the exam. Avoid trying new caffeine or energy products on test day.

Scheduling note for the supplied-break structure

The FE exam is computer-based and includes an optional scheduled break; the exact timing and rules are set by the provider. Confirm break length, whether the clock stops, and what you may access during the break with the provider.

Personal items plan

Most testing rooms prohibit phones, watches, notes, and bags in the testing area; storage rules vary. Confirm what is allowed at your seat and what must be stored.

Exam-day study sheet (for before entry only)

Prepare a one-page summary of high-yield formulas, unit conversions, and sign conventions to review before you enter the room. It cannot be taken inside; leave it in storage.

Pacing plan

Write down your per-question time budget and your strategy for flagging and returning to hard questions. Rehearse this in practice so it is automatic on test day.

Question-flagging habit

Decide in advance how you will mark uncertain questions and how much time you will allow yourself before moving on. Confirm the software's flag and review features with the provider's tutorial.

Backup contact and contingency plan

Save the provider's contact information in case of an emergency or technical issue. If something goes wrong, contact the provider promptly and follow its documented procedure; do not assume an outcome.

Plan the day

Final 72 hours

Shift from learning new material to consolidation. Review your error log and the highest-frequency topics: material and energy balances, fluid mechanics, heat transfer, thermodynamics, reaction engineering, separations, and process control and economics. Do timed mixed sets under exam-like conditions, then spend equal time reviewing why each miss happened. Confirm logistics: test center address, arrival time, ID, calculator approval, and any remote-testing requirements. Stop heavy new-topic study at least 24 hours out.

Final 24 hours

Do a light review only: formula sheet, unit conversions, common sign conventions, and a handful of easy problems to stay sharp. Pack your ID, confirmation, and approved calculator. Set out clothes and travel plan, eat a normal meal, and go to bed at a normal hour. Do not cram late; sleep is worth more than one more practice set. Reconfirm the appointment time and location.

Morning of the exam

Eat a normal breakfast, hydrate moderately, and arrive with buffer for check-in and security. Leave study notes in storage. During the tutorial, use the time to orient yourself to the on-screen reference handbook, calculator interface, and flag/review tools before the clock starts. Take a few calm breaths and start with a steady pace rather than racing.

During the test

Work in passes. First pass: answer questions you know, flag the rest, and keep to your time budget. Second pass: return to flagged items and eliminate wrong options; use the on-screen reference for formulas and unit checks. Watch units and significant figures, and sanity-check magnitudes. Use the scheduled break if offered, but keep it short and return on time. In the final minutes, ensure no question is left unanswered if the software permits answering all items, and confirm your review screen before submitting.

Rules to check

  • Bring only the identification and permitted items your provider allows; confirm the exact ID, calculator, and personal-item rules with the provider before test day, since unapproved items can lead to confiscation or denied entry.

  • Arrive at or before the appointed time. Test centers commonly enforce late-arrival cutoffs; confirm the specific late-arrival and rescheduling policy with the provider rather than assuming a grace period.

  • Electronic devices, notes, and unauthorized reference materials are generally prohibited in the testing area. Confirm storage arrangements and any permitted medical or accessibility accommodations with the provider in advance.

  • The FE exam is computer-based and typically offers an optional scheduled break; confirm break timing, whether the exam clock pauses, and what you may access during the break with the provider.

  • Scoring is typically reported on a pass/fail basis rather than as a raw score, with results released after the exam window. Confirm the current reporting timeline and any diagnostic information the provider releases.

  • Follow all proctor instructions and the provider's candidate agreement. Suspected misconduct or prohibited-item violations are handled under the provider's rules; read the agreement before test day.

  • If a technical problem or emergency occurs during the exam, notify the proctor immediately and follow the provider's documented procedure. Do not attempt to resolve it yourself or assume the attempt will be voided or rescheduled.

  • Confirm in advance what, if anything, you may bring into the testing room and whether any reference material is supplied on screen; do not rely on memory of a previous policy, as rules can change between exam cycles.

FE Chemical FAQ

How many FE Chemical practice questions are available?

The practice set has 200 FE Chemical questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many FE Chemical flashcards are available?

The flashcard set has 32 FE Chemical cards. Each card shows the term and its definition.

Which topics does the FE Chemical study material cover?

The FE Chemical study material covers Chemical Engineering.

What format facts does the catalog list for the FE Chemical exam?

The catalog lists a duration of 320 minutes and these item types: computer-based and multiple choice for the FE Chemical exam.