Adult Echocardiography (AE) Practice Test

Adult Echocardiography

Adult Echocardiography (AE) overview

  • 200 practice questions
  • 32 flashcards
  • 5 study guide topics
  • 37 key terms

What you'll study

  • Cardiac anatomy and physiology20%
  • Ultrasound physics and instrumentation20%
  • Two-dimensional, M-mode, and Doppler acquisition technique20%
  • Valvular heart disease and hemodynamics20%
  • Cardiomyopathy, pericardial disease, and congenital/acquired pathology20%

The Registered Diagnostic Cardiac Sonographer (RDCS) credential is one of the four ARDMS credentials, and ARDMS is described in its own materials as "an Inteleos member community" that has, in its words, set standards for sonography since 1975 - "certification by sonographers, for sonographers." Adult Echocardiography is the RDCS specialty exam for sonographers and physicians who perform and interpret echocardiograms on adult patients, and it is listed by ARDMS alongside Fetal, Pediatric, and other cardiovascular specialties. Because Inteleos describes itself as offering four credentials across eleven unique specialties, candidates should treat Adult Echo as one specialty track rather than a stand-alone certificate. The content outline used by this study set is organised into five areas: cardiac anatomy and physiology; ultrasound physics and instrumentation; two-dimensional, M-mode, and Doppler acquisition technique; valvular heart disease and hemodynamics; and cardiomyopathy, pericardial disease, and congenital or acquired pathology. Effective preparation means working through all five areas rather than only the imaging-heavy ones, since physics and hemodynamics questions are easy to neglect. Build a study calendar around those domains, do practice questions in short timed blocks, and review every miss back to the underlying principle. Note: the official Adult Echocardiography exam page returned an error at the time of retrieval, so no question counts, time limits, fees, or passing scores are published on this page - confirm those on the official Inteleos site before you register. This page is independent study material and is not affiliated with, endorsed by, or sponsored by ARDMS or Inteleos.

Common mistakes

Selecting pulsed-wave (PW) Doppler to interrogate a high-velocity jet (e.g., aortic stenosis, tricuspid regurgitation) and then reporting the aliased waveform's peak velocity or gradient as the true value.

PW is the default 'measurement' mode on many presets and looks cleaner, and candidates forget that the Nyquist limit for cardiac PW at typical depths is only ~1.5-2 m/s, so the envelope wraps and the reported number is falsely low.

What to do instead

Decide mode by expected velocity before you measure: PW (with sample volume) for localization and low-velocity flow, CW for any jet likely to exceed ~1.5-2 m/s. If the spectral display wraps or shows a cut-off envelope, switch to CW, and shift to a non-imaging/ Pedoff probe if the signal is weak. Always scan the full envelope, not the brightest edge.

Measuring peak velocity or gradient with the Doppler cursor visibly off-axis to the flow, or applying an angle-correction value to a cardiac jet to 'fix' a low reading.

On an apical window the cursor often appears aligned when it is 20-30 degrees off the true jet; candidates also carry over the vascular habit of angle correction. Cosine error means a 30-degree misalignment underestimates velocity by ~13% and gradient by ~25%.

What to do instead

Interrogate from at least two windows, align the cursor with the colour/spectral core of the jet, and accept only signals that are crisp, dense, and have a clean, fully filled envelope. Do not angle-correct cardiac Doppler; instead reposition the patient, probe, or window until alignment is achieved.

Mixing peak and mean values: substituting the 4v-squared peak gradient for the mean gradient in severity calls, or pairing an LVOT peak velocity with an aortic VTI (or vice versa) in the continuity equation.

Peak and mean gradients are both printed on the report and look interchangeable; the continuity equation's 'VTI' and 'Vmax' boxes sit next to each other on the machine. The arithmetic still produces a number, so nothing flags the error.

What to do instead

State explicitly which parameter you are reporting. Use mean gradient (traced, averaged over the cardiac cycle and over several beats in irregular rhythms) for severity and for aortic valve area by continuity, and use peak velocity/Vmax consistently in the continuity equation: AVA = (LVOT area x LVOT VTI)/AV VTI, or the Vmax/VTI-matched equivalents.

Measuring the LVOT diameter from a non-zoomed parasternal view, at the level of the aortic sinuses or too far apically, in early systole, or edge-to-edge including the bright endocardial echoes.

The LVOT is small and poorly seen on a standard zoomed-out long-axis; the sinuses are more conspicuous than the annulus, and end-systolic frames look 'fuller'. Because LVOT diameter is squared, a 2 mm error changes valve area by roughly 10-15%.

What to do instead

Zoom on the LVOT in the parasternal long axis, place calipers inner-edge to inner-edge about 0.5-1 cm proximal to the aortic annulus, at mid-systole, with the measurement perpendicular to the long axis. Average over 3 beats and recheck that the same level was used for the VTI sample.

Taking apical views in which the true LV apex is cut off or the chamber is foreshortened, then measuring volumes, ejection fraction, and longitudinal strain from those images.

Foreshortening still produces a plausible-looking four-chamber and a number comes out of the machine, so there is no visible alarm. Candidates chase the mitral valve and forget to drop the transducer intercostally to open up the apex.

What to do instead

Before measuring, confirm the apex sits at the top of the sector with the cavity maximally open and the LV longer than the RV in the four-chamber; move the probe laterally and intercostally, and use the 'longest chamber' view. If the apex cannot be obtained, state that EF is qualitative/limited rather than reporting a foreshortened biplane number.

Grading mitral or aortic regurgitation predominantly from colour jet area or jet length, ignoring vena contracta, PISA/flow convergence, jet density, pressure half-time, and pulmonary vein or aortic flow reversal.

Colour jet area is the most visually striking feature and is easy to eyeball; candidates under-weight the fact that jet area depends heavily on gain, Nyquist limit, driving pressure, and machine preset.

What to do instead

Grade severity with the integrative multiparametric approach: measure vena contracta in the zoomed view at the narrowest neck, calculate PISA radius and regurgitant volume/EROA, assess CW jet density and timing, look for flow reversal, and compare with chamber size. Report colour jet area only as supportive.

Leaving 2D or colour gain too high (or too low), producing tissue 'blooming' into the cavity, colour bleed across valves, or invisible structures, and then making measurements from those images.

Gain is usually set on a previous patient and not re-titrated; excessive gain makes walls feel 'well seen' and colour jets look bigger, which quietly biases wall thickness and regurgitation estimates.

What to do instead

Set 2D gain so the cavity is echo-free while the endocardial border stays distinct, and colour gain just below the point where speckle noise appears in the blood pool. Re-titrate gain and Nyquist limit for every patient and every window, and never compare colour jet sizes acquired at different colour scales.

Assigning a diastolic function grade from the E/A ratio alone, without tissue Doppler e', E/e', left atrial volume index, or tricuspid regurgitation velocity.

E/A is the first number on the mitral inflow display and behaves 'textbook' in normal patients, so pseudo-normal and restrictive patterns get missed. Candidates also forget that E/A varies with heart rate, rhythm, and loading.

What to do instead

Use the full algorithm: measure septal and lateral e' and average, compute E/e', index LA volume, take TR velocity and right atrial pressure, and apply the grading scheme in the correct order. Recheck grade in atrial fibrillation and after loading changes, and state the parameters used.

Mislabelling a pericardial effusion as pleural, or calling tamponade from a large effusion without demonstrating chamber collapse, respiratory inflow variation, or inferior vena cava plethora.

Fluid on the posterior aspect is easy to see but its anatomic relation to the descending aorta (pericardial anterior to it, pleural posterior) is a detail candidates do not routinely check; 'big effusion' is conflated with 'tamponade'.

What to do instead

Confirm location relative to the descending aorta and the pericardial reflection, then look for the physiological markers: right atrial systolic collapse, right ventricular diastolic collapse, >25-30% mitral inflow respiratory variation, and a dilated non-collapsing IVC. Grade by size plus haemodynamic impact, not size alone.

Measuring LV chamber dimensions or wall thickness from an M-mode cursor that is not perpendicular to the LV long axis (or from a 2D-guided line that drifts off the minor axis), then reporting those numbers as septal/lateral dimensions.

The M-mode cursor is left where it happened to be, the tracing looks crisp even when oblique, and oblique cuts slice the ventricle at an angle that overstates both cavity size and wall thickness.

What to do instead

Use 2D-guided M-mode, placing the cursor through the chamber just beyond the mitral leaflet tips, perpendicular to the septal-posterior axis and clearly through the LV centre. Confirm with a visual check on the 2D image that the line crosses the minor axis, and prefer 2D measurements when the ventricle is dilated or distorted.

Exam requirements can change. Confirm current details with the exam provider.

Adult Echocardiography (AE) practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Cardiac anatomy and physiology

    A normal adult aortic valve is composed of how many cusps or leaflets?

    1. Three Correct answer.
    2. Four
    3. One
    4. Two

    Explanation

    The normal aortic valve is tricuspid, consisting of right, left, and non-coronary cusps. A bicuspid valve is the most common congenital cardiac anomaly but does not represent normal adult anatomy.

  2. Question 2Cardiac anatomy and physiology

    Within the normal mitral valve, which leaflet is the taller, sail-shaped structure that separates inflow from the left ventricular outflow tract?

    1. Medial scallop
    2. Posterior leaflet
    3. Lateral scallop
    4. Anterior leaflet Correct answer.

    Explanation

    The anterior (aortic) mitral leaflet is taller and more mobile and lies between the inflow and outflow tracts. The posterior leaflet is shorter in height but attaches to a longer portion of the annulus and is divided into three scallops.

  3. Question 3Cardiac anatomy and physiology

    Which structure is a normal muscular band that crosses the right ventricular cavity from the septum to the free wall?

    1. Crista terminalis
    2. Moderator band Correct answer.
    3. Coumadin ridge
    4. Chiari network

    Explanation

    The moderator band (trabecula septomarginalis) traverses the right ventricular cavity and carries part of the right bundle branch. It is a reliable landmark for identifying the right ventricle.

  4. Question 4Cardiac anatomy and physiology

    A left ventricle has an end-diastolic volume of 120 mL and an end-systolic volume of 50 mL. What is the stroke volume?

    1. 2.4 mL
    2. 170 mL
    3. 50 mL
    4. 70 mL Correct answer.

    Explanation

    Stroke volume is the difference between end-diastolic and end-systolic volume: 120 mL minus 50 mL equals 70 mL.

  5. Question 5Cardiac anatomy and physiology

    Which range best represents a normal left ventricular ejection fraction by two-dimensional echocardiography?

    1. 30% to 45%
    2. 45% to 54%
    3. 55% to 70% Correct answer.
    4. 75% to 90%

    Explanation

    A normal left ventricular ejection fraction is generally 55% to 70%. Values between 45% and 54% are borderline, and values below 45% indicate reduced systolic function.

  6. Question 6Cardiac anatomy and physiology

    Left ventricular myocardial perfusion occurs predominantly during which phase of the cardiac cycle?

    1. Peak systole
    2. Diastole Correct answer.
    3. Isovolumic relaxation
    4. Isovolumic contraction

    Explanation

    Left coronary flow occurs mainly in diastole because systolic myocardial contraction compresses the intramural vessels. Tachycardia shortens diastole and can compromise subendocardial perfusion.

  7. Question 7Cardiac anatomy and physiology

    The normal tricuspid valve has how many leaflets?

    1. Three Correct answer.
    2. Five
    3. Two
    4. Four

    Explanation

    The tricuspid valve normally has three leaflets (anterior, posterior, and septal) and three papillary muscles.

  8. Question 8Cardiac anatomy and physiology

    Which pericardial layer lies directly on the surface of the myocardium?

    1. Parietal serous layer
    2. Visceral serous layer Correct answer.
    3. Fibrous pericardium
    4. Pericardial cavity

    Explanation

    The visceral serous pericardium, also called the epicardium, is applied directly to the myocardium. The parietal serous layer lines the fibrous pericardium, and the pericardial cavity separates the two serous layers.

  9. Question 9Cardiac anatomy and physiology

    The coronary sinus empties into which cardiac chamber?

    1. Left atrium
    2. Right atrium Correct answer.
    3. Right ventricle
    4. Left ventricle

    Explanation

    The coronary sinus collects most of the cardiac venous drainage and empties into the right atrium near the inferior vena cava and tricuspid annulus.

  10. Question 10Cardiac anatomy and physiology

    The left atrial appendage is best described as lying:

    1. Within the interatrial septum
    2. At the left ventricular apex
    3. Adjacent to the left upper pulmonary vein Correct answer.
    4. Posterior to the right superior pulmonary vein

    Explanation

    The left atrial appendage is a hook-shaped pouch at the anterolateral aspect of the left atrium, closely related to the left upper pulmonary vein and separated from it by the Coumadin ridge.

  11. Question 11Cardiac anatomy and physiology

    Within physiologic limits, increasing left ventricular preload produces which change according to the Frank-Starling relationship?

    1. Increased stroke volume Correct answer.
    2. Reduced stroke volume
    3. Reduced myocardial fiber length
    4. Reduced cardiac output

    Explanation

    Greater preload stretches the myocardial fibers and increases sarcomere length, which enhances force generation and raises stroke volume within physiologic limits.

  12. Question 12Cardiac anatomy and physiology

    Using the simplified Bernoulli equation, what pressure gradient corresponds to a peak velocity of 3 m/s?

    1. 9 mmHg
    2. 36 mmHg Correct answer.
    3. 18 mmHg
    4. 72 mmHg

    Explanation

    The simplified Bernoulli equation is ΔP = 4v². For a velocity of 3 m/s, 4 × 3² equals 36 mmHg.

  13. Question 13Cardiac anatomy and physiology

    Which expression correctly applies the continuity equation to calculate aortic valve area?

    1. LVOT area × aortic valve VTI ÷ LVOT VTI
    2. Aortic valve VTI ÷ LVOT VTI
    3. (LVOT area × LVOT VTI) ÷ aortic valve VTI Correct answer.
    4. (LVOT diameter × LVOT VTI) ÷ aortic valve VTI

    Explanation

    Conservation of flow requires that aortic valve area equals the LVOT cross-sectional area multiplied by the LVOT velocity-time integral, divided by the aortic valve velocity-time integral.

  14. Question 14Cardiac anatomy and physiology

    During isovolumic contraction, which statement about the mitral and aortic valves is true?

    1. Both the mitral and aortic valves are closed Correct answer.
    2. Both the mitral and aortic valves are open
    3. The mitral valve is open and the aortic valve is closed
    4. The aortic valve is open and the mitral valve is closed

    Explanation

    Isovolumic contraction begins with mitral closure and ends with aortic opening. During this interval both valves are closed and ventricular pressure rises at constant volume.

  15. Question 15Cardiac anatomy and physiology

    A reduced medial mitral annular e′ velocity on tissue Doppler most directly indicates:

    1. Impaired left ventricular relaxation Correct answer.
    2. Pericardial constriction
    3. Severe aortic stenosis
    4. Increased left ventricular contractility

    Explanation

    Annular e′ reflects the rate of myocardial lengthening in early diastole, so a low e′ indicates impaired relaxation and is less load-dependent than mitral inflow velocities.

  16. Question 16Cardiac anatomy and physiology

    A short mitral inflow E-wave deceleration time of less than 160 ms in a patient with reduced ejection fraction suggests:

    1. Mild grade I diastolic dysfunction
    2. Normal diastolic function
    3. Constrictive pericarditis
    4. Elevated left atrial pressure Correct answer.

    Explanation

    A short deceleration time reflects rapid equalization of left atrial and left ventricular pressures, a restrictive filling pattern associated with high left atrial pressure and adverse prognosis.

  17. Question 17Cardiac anatomy and physiology

    Which method is the recommended two-dimensional technique for measuring left ventricular volumes and ejection fraction?

    1. Cube formula
    2. Area-length method from long axis
    3. Teichholz formula
    4. Biplane disks method Correct answer.

    Explanation

    The biplane method of disks (modified Simpson's rule) traces the endocardial border in two orthogonal planes and sums disk volumes, making it the recommended two-dimensional approach.

  18. Question 18Cardiac anatomy and physiology

    According to the Laplace relationship, left ventricular wall stress increases when:

    1. Both radius and thickness decrease
    2. Both radius and thickness increase
    3. Chamber radius increases Correct answer.
    4. Wall thickness increases

    Explanation

    Wall stress is proportional to chamber radius and inversely proportional to wall thickness, so a larger chamber with unchanged wall thickness faces greater stress.

  19. Question 19Cardiac anatomy and physiology

    Regurgitant volume across an insufficient valve can be calculated as:

    1. Jet VTI divided by EROA
    2. EROA divided by VTI
    3. EROA times heart rate
    4. EROA times jet VTI Correct answer.

    Explanation

    Regurgitant volume equals the effective regurgitant orifice area multiplied by the velocity-time integral of the regurgitant jet.

  20. Question 20Cardiac anatomy and physiology

    The aortic valve opens at the moment when:

    1. Aortic pressure exceeds left ventricular pressure
    2. Left ventricular volume is at its minimum
    3. Left ventricular pressure exceeds aortic pressure Correct answer.
    4. Left atrial pressure exceeds left ventricular pressure

    Explanation

    The aortic valve opens when left ventricular pressure rises above aortic diastolic pressure, terminating isovolumic contraction and beginning ejection.

  21. Question 21Cardiac anatomy and physiology

    Coronary flow velocity reserve is calculated as:

    1. Hyperemic velocity minus resting velocity
    2. Resting velocity multiplied by heart rate
    3. Resting divided by hyperemic velocity
    4. Hyperemic divided by resting velocity Correct answer.

    Explanation

    Coronary flow velocity reserve is the ratio of hyperemic, usually adenosine-induced, to resting diastolic coronary flow velocity. A value below about 2.0 suggests impaired epicardial or microvascular reserve.

  22. Question 22Cardiac anatomy and physiology

    Under laminar flow conditions, volume flow through a vessel varies in proportion to which expression for the vessel radius?

    1. Cube of the vessel radius
    2. Square of the radius and vessel length
    3. Fourth power of radius Correct answer.
    4. First power of the radius

    Explanation

    In the Poiseuille relationship, resistance is inversely proportional to the fourth power of the radius, so flow varies with radius to the fourth power. Small changes in radius therefore produce large changes in flow.

  23. Question 23Cardiac anatomy and physiology

    In cardiac myocytes, calcium entering through L-type channels during the plateau phase triggers:

    1. Phosphorylation of myosin light chains
    2. Sarcoplasmic reticulum calcium release Correct answer.
    3. Mitochondrial calcium accumulation
    4. Closure of L-type calcium channels

    Explanation

    Calcium entry during the plateau triggers calcium-induced calcium release from the sarcoplasmic reticulum through ryanodine receptors. The resulting rise in cytosolic calcium initiates contraction.

  24. Question 24Cardiac anatomy and physiology

    At rest, the coronary circulation extracts approximately what fraction of the oxygen delivered in arterial blood?

    1. 70% to 80% Correct answer.
    2. 10% to 20%
    3. 25% to 35%
    4. 40% to 50%

    Explanation

    The myocardium extracts about 70% to 80% of delivered oxygen at rest, close to the maximum. Increased oxygen demand must therefore be met mainly by increasing coronary blood flow.

  25. Question 25Cardiac anatomy and physiology

    Which factor best explains the higher resting oxygen consumption of the left ventricle compared with the right ventricle?

    1. Higher systolic wall stress Correct answer.
    2. Lower coronary flow reserve
    3. Greater chamber compliance
    4. Thinner free wall

    Explanation

    Left ventricular systolic pressure and wall stress are far higher than those of the right ventricle, and wall stress is the major determinant of myocardial oxygen demand. Chamber compliance and coronary reserve do not explain the difference in demand.

  26. Question 26Cardiac anatomy and physiology

    Which cardiac chamber forms the apex of the heart?

    1. Right ventricle
    2. Left ventricle Correct answer.
    3. Left atrium
    4. Right atrium

    Explanation

    The left ventricle forms the cardiac apex because its thick myocardial wall extends inferiorly and to the left. The right ventricle forms most of the anterior surface, while the atria occupy the base of the heart.

  27. Question 27Cardiac anatomy and physiology

    The moderator band is a normal muscular structure located within which chamber?

    1. Left ventricular cavity
    2. Right ventricle Correct answer.
    3. Left atrial chamber
    4. Right atrial chamber

    Explanation

    The moderator band, or septomarginal trabecula, extends from the interventricular septum to the anterior papillary muscle in the right ventricle. It carries part of the conduction system and is a recognized right ventricular landmark.

  28. Question 28Cardiac anatomy and physiology

    The fossa ovalis is a remnant located on which structure?

    1. Mitral annulus
    2. Aortic root
    3. Interatrial septum Correct answer.
    4. Ventricular septum

    Explanation

    The fossa ovalis is the residual depression of the foramen ovale on the right atrial side of the interatrial septum. It is an important landmark for transseptal puncture and for identifying the atrial septum on echocardiography.

  29. Question 29Cardiac anatomy and physiology

    Which great vessel originates from the right ventricle?

    1. Pulmonary veins
    2. Aorta
    3. Pulmonary artery Correct answer.
    4. Superior vena cava

    Explanation

    The right ventricle ejects blood through the pulmonary valve into the main pulmonary artery. The aorta arises from the left ventricle, while the venae cavae and pulmonary veins return blood to the atria.

  30. Question 30Cardiac anatomy and physiology

    Which coronary artery most commonly supplies the anterior two-thirds of the interventricular septum?

    1. Posterior descending artery
    2. Left circumflex artery
    3. LAD artery Correct answer.
    4. Right coronary artery

    Explanation

    The left anterior descending artery gives off septal perforator branches that supply the anterior and middle portions of the interventricular septum. The posterior descending artery typically supplies the posterior one-third of the septum.

  31. Question 31Cardiac anatomy and physiology

    The sinoatrial node lies at the junction of which two structures?

    1. Pulmonary veins and left atrium
    2. Aorta and pulmonary trunk
    3. SVC and right atrium
    4. IVC and right atrium Correct answer.

    Explanation

    The sinoatrial node is located at the superior cavoatrial junction, where the superior vena cava enters the right atrium. This site allows it to serve as the dominant pacemaker of the heart.

  32. Question 32Cardiac anatomy and physiology

    The posteromedial papillary muscle differs from the anterolateral papillary muscle in that it usually:

    1. Attaches directly to the ventricular septum
    2. Supports the aortic leaflets
    3. Receives a dual blood supply
    4. Has a single blood supply Correct answer.

    Explanation

    The posteromedial papillary muscle usually receives blood from a single source, either the right coronary artery or the left circumflex artery. This makes it more vulnerable to ischemic rupture than the anterolateral papillary muscle, which often has a dual supply.

  33. Question 33Cardiac anatomy and physiology

    On an aortic pressure tracing, the dicrotic notch coincides with which event?

    1. Peak left atrial pressure
    2. Closure of the pulmonary valve
    3. Opening of the mitral valve
    4. Closure of the aortic valve Correct answer.

    Explanation

    The dicrotic notch reflects the brief reversal of aortic flow that occurs when the aortic valve closes at end systole. It marks the beginning of diastole in the aortic pressure waveform.

  34. Question 34Cardiac anatomy and physiology

    On a left ventricular pressure-volume loop, the area enclosed by the loop represents:

    1. Myocardial oxygen consumption
    2. Coronary flow reserve
    3. Left atrial work
    4. Stroke work Correct answer.

    Explanation

    The area within the pressure-volume loop equals stroke volume multiplied by the developed pressure, which is stroke work. Myocardial oxygen consumption correlates with work but is not directly equal to the loop area.

  35. Question 35Cardiac anatomy and physiology

    Which left ventricular wall segment is supplied by the posterior descending artery in a right-dominant system?

    1. Lateral wall
    2. Inferior wall Correct answer.
    3. Anterior septum
    4. Anterolateral wall

    Explanation

    In a right-dominant system, the posterior descending artery arises from the right coronary artery and supplies the inferior wall and posterior septum. The anterior septum and anterolateral wall are supplied mainly by the left anterior descending artery.

  36. Question 36Cardiac anatomy and physiology

    The great cardiac vein travels in which sulcus?

    1. Coronary sinus sulcus
    2. Posterior atrioventricular sulcus
    3. Anterior interventricular sulcus Correct answer.
    4. Right atrioventricular sulcus

    Explanation

    The great cardiac vein ascends in the anterior interventricular sulcus alongside the left anterior descending artery. It then curves around the left atrioventricular groove to continue as the coronary sinus.

  37. Question 37Cardiac anatomy and physiology

    During a normal cardiac cycle, which event occurs first after the QRS complex on the ECG?

    1. Opening of the mitral valve
    2. Peak mitral inflow E wave
    3. Closure of the aortic valve
    4. Closure of the mitral valve Correct answer.

    Explanation

    The QRS complex marks ventricular depolarization, which is followed almost immediately by mitral valve closure and the onset of isovolumic contraction. Aortic valve opening occurs later, after left ventricular pressure exceeds aortic pressure.

  38. Question 38Cardiac anatomy and physiology

    Which embryologic structure gives rise to the coronary sinus?

    1. Bulbus cordis
    2. Right horn of the sinus venosus
    3. Left horn of the sinus venosus Correct answer.
    4. Septum primum

    Explanation

    The coronary sinus develops from the left horn of the sinus venosus. The right horn of the sinus venosus contributes to the smooth-walled portion of the right atrium.

  39. Question 39Cardiac anatomy and physiology

    In a left-dominant coronary system, which artery gives rise to the posterior descending artery?

    1. Right coronary artery
    2. Left anterior descending artery
    3. Left circumflex artery Correct answer.
    4. First diagonal branch

    Explanation

    Coronary dominance is defined by the artery that supplies the posterior descending artery. In a left-dominant system, the posterior descending artery arises from the left circumflex artery.

  40. Question 40Cardiac anatomy and physiology

    Which pericardial recess lies posterior to the left atrium and is bounded by the pulmonary veins?

    1. Transverse sinus
    2. Oblique sinus Correct answer.
    3. Anterior interventricular sulcus
    4. Coronary sinus

    Explanation

    The oblique pericardial sinus is a blind recess posterior to the left atrium, bounded laterally by the pulmonary veins and inferiorly by the inferior vena cava. The transverse sinus lies more superiorly, posterior to the aorta and pulmonary trunk.

  41. Question 41Ultrasound physics and instrumentation

    Clinical ultrasound scanners assume an average propagation speed through soft tissue of:

    1. 4080 m/s
    2. 1540 m/s Correct answer.
    3. 1450 m/s
    4. 331 m/s

    Explanation

    Almost all soft-tissue imaging assumes a speed of 1540 m/s, which is used to convert echo return time into depth. Tissues with very different speeds, such as lung, bone and fat, cause the displayed position of structures to be inaccurate.

  42. Question 42Ultrasound physics and instrumentation

    If the transmitted frequency is increased while propagation speed stays constant, the wavelength:

    1. It decreases Correct answer.
    2. It stays the same
    3. It doubles
    4. It increases proportionally

    Explanation

    Wavelength equals propagation speed divided by frequency. With speed held constant, wavelength and frequency are inversely related, so a higher frequency produces a shorter wavelength and better axial resolution.

  43. Question 43Ultrasound physics and instrumentation

    The piezoelectric element of an imaging transducer functions to:

    1. It focuses the beam by refraction at the skin surface
    2. It converts electrical energy into acoustic energy and back Correct answer.
    3. It amplifies the returning echo signal before it is digitised
    4. It stores the returning echoes as digital data

    Explanation

    Piezoelectric crystals deform when a voltage is applied and generate a voltage when deformed, so the same element both transmits and receives. Beam formation, amplification and storage are handled by other components of the system.

  44. Question 44Ultrasound physics and instrumentation

    The purpose of time gain compensation is to:

    1. It increases the overall brightness of the entire image uniformly
    2. It compensates for attenuation by increasing gain with depth Correct answer.
    3. It filters out low-frequency Doppler shifts from moving tissue
    4. It narrows the sector width to improve frame rate

    Explanation

    Echoes from deeper structures are weaker because of attenuation along the round-trip path. Time gain compensation applies progressively greater amplification at later arrival times so that similar reflectors appear equally bright at all depths.

  45. Question 45Ultrasound physics and instrumentation

    Which practice best follows the ALARA principle during a transthoracic echocardiogram?

    1. Applying colour Doppler over the whole sector by default
    2. Prolonging the examination to document additional normal variants
    3. Using the lowest output power that gives diagnostic images Correct answer.
    4. Maximising output power to reduce noise in all patients

    Explanation

    ALARA means keeping acoustic exposure as low as reasonably achievable while still obtaining the diagnostic information needed. Output power, dwell time and selection of modes such as colour or Doppler all contribute to patient exposure.

  46. Question 46Ultrasound physics and instrumentation

    The thermal index displayed on an ultrasound system estimates the:

    1. Tissue heating from absorbed acoustic energy Correct answer.
    2. Peak negative pressure of the transmitted pulse
    3. Amount of signal amplification applied by the receiver
    4. Likelihood of microbubble collapse in tissue

    Explanation

    The thermal index relates to the potential for temperature rise as acoustic energy is absorbed and converted to heat. The mechanical index, in contrast, relates to non-thermal effects such as cavitation.

  47. Question 47Ultrasound physics and instrumentation

    Compared with two-dimensional imaging, M-mode provides:

    1. Better lateral resolution across the sector
    2. A wider field of view of the ventricles
    3. Improved colour Doppler sensitivity
    4. Better temporal resolution along one line Correct answer.

    Explanation

    M-mode samples a single line with a high pulse repetition frequency, so the sampling rate along that line is very high. This allows precise timing of rapid events such as valve motion or wall excursion, at the expense of spatial coverage.

  48. Question 48Ultrasound physics and instrumentation

    Continuous-wave Doppler is characterised by:

    1. Aliasing whenever velocity exceeds 1.5 m/s
    2. Continuous transmission with no range resolution Correct answer.
    3. A single crystal that alternates transmission and reception
    4. Range resolution that improves as PRF increases

    Explanation

    Continuous-wave Doppler uses separate elements to transmit and receive simultaneously along the whole line of sight. Because echoes are received continuously, no depth information is available, but there is no Nyquist limit and therefore no aliasing.

  49. Question 49Ultrasound physics and instrumentation

    Axial resolution is determined primarily by the:

    1. Beam width at the focal zone
    2. Spatial pulse length Correct answer.
    3. Line density of the scan converter
    4. Element thickness of the matching layer

    Explanation

    Axial resolution equals half the spatial pulse length, so shorter pulses discriminate reflectors that are closer together along the beam. Pulse length is set by the number of cycles and the wavelength, so higher frequency and fewer cycles both improve it.

  50. Question 50Ultrasound physics and instrumentation

    A pulsed-wave Doppler system operating at a pulse repetition frequency of 5000 Hz has a Nyquist limit of:

    1. 10 000 Hz
    2. 1250 Hz
    3. 2500 Hz Correct answer.
    4. 5000 Hz

    Explanation

    The Nyquist limit is half the pulse repetition frequency, so 5000 Hz gives 2500 Hz. Doppler shifts above this value are aliased and displayed at an incorrect velocity or direction.

  51. Question 51Ultrasound physics and instrumentation

    The Doppler beam intercepts flow at an angle of 60°. Compared with a 0° angle, the measured velocity will be:

    1. Unchanged
    2. Reduced by a factor of four
    3. Doubled
    4. Halved Correct answer.

    Explanation

    The Doppler equation includes the cosine of the angle between the beam and flow direction. The cosine of 60° is 0.5, so only half of the true velocity is detected when angle correction is not applied.

  52. Question 52Ultrasound physics and instrumentation

    Attenuation of ultrasound in soft tissue:

    1. Decreases as frequency rises
    2. Increases with frequency Correct answer.
    3. Is greater in blood than in bone
    4. Is independent of frequency

    Explanation

    Attenuation includes absorption, reflection and scattering, and the attenuation coefficient rises roughly in proportion to frequency. Higher frequencies therefore give better resolution but poorer penetration in deep tissue.

  53. Question 53Ultrasound physics and instrumentation

    Increasing the displayed imaging depth from 10 cm to 20 cm, with all other settings unchanged, will:

    1. Leave the frame rate unchanged
    2. Double the frame rate
    3. Halve the frame rate Correct answer.
    4. Improve axial resolution

    Explanation

    Frame rate equals the pulse repetition frequency divided by the number of lines per frame. Doubling the depth doubles the round-trip time for each pulse, which halves the maximum PRF and therefore approximately halves the frame rate.

  54. Question 54Ultrasound physics and instrumentation

    Tissue harmonic imaging improves image quality mainly because:

    1. Frame rate is increased by transmitting at higher frequency
    2. Artifact from side lobes and reverberation is reduced Correct answer.
    3. Harmonic frequencies attenuate less than fundamental frequencies
    4. Harmonic signals have a higher Nyquist limit

    Explanation

    Harmonics are generated within tissue and received at twice the transmitted frequency. They arise mainly in the central, high-intensity portion of the beam, so side lobe and reverberation artifact is weak relative to the fundamental signal, improving clarity and lateral resolution.

  55. Question 55Ultrasound physics and instrumentation

    The mechanical index is calculated as:

    1. Transmitted power divided by the pulse repetition frequency
    2. Peak positive pressure divided by the square root of frequency
    3. Average intensity multiplied by the beam area
    4. Peak negative pressure divided by the square root of frequency Correct answer.

    Explanation

    The mechanical index uses the peak rarefactional (negative) pressure in MPa divided by the square root of the transmitted frequency in MHz. It estimates the likelihood of cavitation, with higher values implying greater risk.

  56. Question 56Ultrasound physics and instrumentation

    Reducing the displayed dynamic range of an ultrasound image mainly:

    1. Increases the frame rate
    2. Increases contrast and reduces the shades of grey Correct answer.
    3. Improves axial resolution
    4. Removes echoes that are returning from deep structures

    Explanation

    Dynamic range is the range of echo amplitudes that can be shown. Narrowing it compresses a smaller amplitude range into the available grey shades, so differences between weak and strong reflectors become more obvious and the image appears more black and white.

  57. Question 57Ultrasound physics and instrumentation

    On a colour Doppler display that uses variance mapping, bright green within a jet most likely indicates:

    1. Turbulent, multidirectional flow Correct answer.
    2. Flow moving away from the transducer at low velocity
    3. Absent flow
    4. Laminar high-velocity flow

    Explanation

    Variance mapping adds a second colour that reflects the spread of velocities within a sample volume. A wide distribution of speeds and directions, as occurs in a turbulent jet, produces the variance colour, whereas laminar flow has a narrow distribution.

  58. Question 58Ultrasound physics and instrumentation

    The proportion of ultrasound reflected at a tissue interface is determined mainly by:

    1. The pulse repetition frequency
    2. The transmitted frequency and receiver gain together
    3. The duration of the transmitted pulse
    4. The impedance difference between the two media Correct answer.

    Explanation

    Acoustic impedance is the product of density and propagation speed. A large impedance mismatch, such as at soft tissue–bone or soft tissue–gas boundaries, reflects most of the incident beam, which is why these interfaces are strong reflectors or barriers.

  59. Question 59Ultrasound physics and instrumentation

    A pulsed-wave Doppler tracing shows echoes from structures at twice the selected depth range. This is caused by:

    1. A pulse repetition frequency that is set too low
    2. A wall filter that is set higher than necessary
    3. A pulse repetition frequency that is too high Correct answer.
    4. A Doppler angle greater than 60 degrees from the beam

    Explanation

    Pulsed Doppler assumes each echo belongs to the most recently emitted pulse. If the PRF is too high for the depth being interrogated, echoes from an earlier pulse arrive after the next pulse has been sent and are displayed at the wrong, shallower depth, producing range ambiguity.

  60. Question 60Ultrasound physics and instrumentation

    Elevational (slice-thickness) resolution is determined mainly by:

    1. Pulse duration
    2. The displayed dynamic range
    3. The thickness of the beam slice Correct answer.
    4. The number of scan lines per frame

    Explanation

    The beam has a finite thickness in the plane perpendicular to the image, set by the elevation focus of the transducer. Structures lying above one another within that slice thickness cannot be separated, even if they are well resolved laterally and axially.

  61. Question 61Ultrasound physics and instrumentation

    The matching layer of an imaging transducer is manufactured to a thickness of:

    1. One full wavelength in the matching layer
    2. One quarter of the wavelength in the matching layer Correct answer.
    3. One tenth of the wavelength in the matching layer
    4. One half of the wavelength measured in the matching layer

    Explanation

    A quarter-wave layer makes reflections from its front and back surfaces arrive 180° out of phase, so they cancel and more energy passes into tissue. This improves transmission between the high-impedance crystal and low-impedance soft tissue.

  62. Question 62Ultrasound physics and instrumentation

    Grating lobes are produced by:

    1. Multiple reflections between the transducer and a strong reflector
    2. Periodic spacing of elements in an array transducer Correct answer.
    3. Refraction at the boundary between fat and muscle
    4. Non-linear propagation in tissue at high intensity

    Explanation

    The regular spacing of elements in an array behaves like a diffraction grating and generates off-axis beams called grating lobes when element spacing approaches the wavelength. These lobes can create echoes that appear to originate from positions outside the main beam.

  63. Question 63Ultrasound physics and instrumentation

    A high wall filter setting on a pulsed-wave Doppler study will:

    1. Increase the Nyquist limit and remove aliasing
    2. Shift the baseline upward to display higher velocities
    3. Remove low-velocity signals arising from moving myocardium Correct answer.
    4. Reduce the sample volume size and improve range resolution

    Explanation

    The wall filter is a high-pass filter that rejects Doppler shifts below a chosen threshold, suppressing strong signals from moving myocardium and vessel walls. If set too high it also removes genuine slow blood flow.

  64. Question 64Ultrasound physics and instrumentation

    Which adjustment will most effectively eliminate aliasing in a pulsed-wave Doppler recording of a high-velocity jet?

    1. Raising the scale and shifting the baseline Correct answer.
    2. Placing the Doppler beam at 90 degrees to flow
    3. Setting the wall filter to its maximum value
    4. Increasing the size of the Doppler sample volume

    Explanation

    Aliasing occurs when the Doppler shift exceeds the Nyquist limit, which is half the PRF. Increasing the velocity scale raises the PRF and hence the Nyquist limit, while baseline shift repositions the display so the peak fits within the unambiguous range.

  65. Question 65Ultrasound physics and instrumentation

    During contrast-enhanced echocardiography, a high mechanical index will:

    1. Improve microbubble persistence for late-phase imaging
    2. Have no measurable effect on the microbubbles
    3. Destroy the microbubbles, limiting their duration Correct answer.
    4. Increase the half-value layer of the contrast agent

    Explanation

    Microbubbles are fragile and collapse when exposed to high acoustic pressures, which the mechanical index reflects. Low-MI techniques preserve bubbles for continuous opacification, whereas deliberately high MI is used to destroy bubbles for replenishment or perfusion studies.

  66. Question 66Ultrasound physics and instrumentation

    The average speed of ultrasound through soft tissue is approximately:

    1. 5500 m/s
    2. 330 m/s
    3. 4080 m/s
    4. 1540 m/s Correct answer.

    Explanation

    Soft tissue transmits ultrasound at an average speed of about 1540 m/s, and most scanner depth calibrations assume this value. Speed varies with tissue stiffness and density, being much lower in air and much higher in bone.

  67. Question 67Ultrasound physics and instrumentation

    The active element of a diagnostic ultrasound transducer generates sound by means of:

    1. thermal expansion of a heated matching layer
    2. piezoelectric vibration of a crystal Correct answer.
    3. photoelectric emission from the transducer face
    4. electromagnetic induction within a copper coil

    Explanation

    Certain crystals and ceramics change thickness when a voltage is applied across them, producing mechanical vibration and thus sound; the reverse effect detects returning echoes. This bidirectional property is the piezoelectric effect.

  68. Question 68Ultrasound physics and instrumentation

    The backing (damping) block of a pulsed-echo transducer is designed mainly to:

    1. damp crystal ringing and shorten the pulse Correct answer.
    2. increase the emitted acoustic power
    3. match the crystal impedance to skin
    4. focus the beam at the selected focal zone

    Explanation

    The backing block absorbs energy radiated backward and suppresses continued crystal oscillation. This shortens the spatial pulse length and improves axial resolution, while broadening the transducer bandwidth and slightly reducing sensitivity.

  69. Question 69Ultrasound physics and instrumentation

    Time gain compensation is used to:

    1. vary the pulse repetition frequency with depth
    2. remove aliasing from the Doppler spectrum
    3. amplify returning echoes progressively with depth Correct answer.
    4. adjust the displayed colour map

    Explanation

    Echoes from deeper structures are weaker because attenuation increases with distance. Time gain compensation applies increasing amplification as a function of arrival time, so that similar reflectors appear similarly bright at different depths.

  70. Question 70Ultrasound physics and instrumentation

    A pulsed-wave Doppler examination is performed at a depth of 7 cm. The highest pulse repetition frequency that avoids range ambiguity is approximately:

    1. 11,000 Hz Correct answer.
    2. 5,500 Hz
    3. 22,000 Hz
    4. 44,000 Hz

    Explanation

    The pulse must travel to the sample volume and back before the next pulse is emitted, so PRF is limited by PRF = c/(2d). With c = 1540 m/s and d = 7 cm, PRF is about 11,000 Hz.

  71. Question 71Ultrasound physics and instrumentation

    At a fixed depth, which change will most improve lateral resolution of a phased-array image?

    1. increasing the displayed dynamic range
    2. decreasing the transmit frequency
    3. increasing the wall filter setting
    4. a larger aperture focused at that depth Correct answer.

    Explanation

    Lateral resolution is determined by beam width, which narrows with a larger aperture, a higher frequency, and focusing at the depth of interest. It is independent of display dynamic range and Doppler filter settings.

  72. Question 72Ultrasound physics and instrumentation

    With depth and line density unchanged, narrowing the sector width from 90° to 45° will:

    1. roughly double the frame rate Correct answer.
    2. leave the frame rate unchanged
    3. double the axial resolution of the image
    4. halve the frame rate of the display

    Explanation

    Frame rate is the pulse repetition frequency divided by the number of scan lines per frame. Halving the sector angle at constant line density halves the number of lines, so the frame rate approximately doubles.

  73. Question 73Ultrasound physics and instrumentation

    A duplicated structure appearing on the far side of a strong specular reflector, at a distance equal to its true distance from the reflector, is called:

    1. acoustic enhancement
    2. range ambiguity
    3. a comet-tail artifact
    4. a mirror-image artifact Correct answer.

    Explanation

    A strong flat reflector can redirect echoes so that the scanner displays a virtual image behind it. The duplicate lies beyond the reflector at a distance matching the true object's distance from the reflector.

  74. Question 74Ultrasound physics and instrumentation

    In pulsed-wave Doppler, the length of the sample volume is determined primarily by the:

    1. pulse duration and receiver gate length Correct answer.
    2. the angle between the beam and the vessel
    3. the wall filter setting selected by the operator
    4. the colour scale and baseline position

    Explanation

    The sample volume length equals the spatial pulse length plus the duration of the receiver gate, converted to distance. Shortening the pulse or the gate narrows the sample volume and improves depth selectivity.

  75. Question 75Ultrasound physics and instrumentation

    Increased brightness deep to a simple cyst is caused by:

    1. total reflection at the anterior cyst wall
    2. refraction at the lateral cyst edge
    3. reverberation within the cyst fluid
    4. less attenuation in fluid than in tissue Correct answer.

    Explanation

    Fluid attenuates ultrasound much less than the surrounding solid tissue, so echoes returning from deep to the cyst are stronger than those from adjacent tissue at the same depth. This produces posterior acoustic enhancement.

  76. Question 76Ultrasound physics and instrumentation

    Using an average soft-tissue attenuation of 0.5 dB/cm/MHz, the total attenuation of a 4 MHz pulse that travels to a depth of 10 cm and returns to the transducer is:

    1. 80 dB
    2. 10 dB
    3. 40 dB Correct answer.
    4. 20 dB

    Explanation

    One-way attenuation is 0.5 dB/cm/MHz × 4 MHz × 10 cm = 20 dB. The pulse traverses the same path twice, so the round-trip attenuation is 40 dB.

  77. Question 77Ultrasound physics and instrumentation

    A Doppler beam intersects a vessel at 90°. The detected Doppler shift will be:

    1. maximal
    2. essentially zero Correct answer.
    3. half maximal
    4. aliased

    Explanation

    The Doppler equation includes the cosine of the angle between the beam and flow. At 90° the cosine is zero, so no measurable frequency shift is produced even when flow is present.

  78. Question 78Ultrasound physics and instrumentation

    Multiple equally spaced echoes appearing deep to a strong reflector such as a metallic pacing lead are most consistent with:

    1. shadowing
    2. side lobe artifact
    3. mirror image
    4. reverberation Correct answer.

    Explanation

    Reverberation occurs when sound bounces repeatedly between two strong reflectors or within a highly reflective structure. Each additional round trip produces another echo at a fixed spacing, creating a series of equally spaced copies.

  79. Question 79Ultrasound physics and instrumentation

    A transducer produces a pulse of 0.5 μs duration in tissue. The axial resolution is approximately:

    1. 3.08 mm
    2. 0.39 mm Correct answer.
    3. 1.54 mm
    4. 0.77 mm

    Explanation

    Spatial pulse length is speed multiplied by pulse duration: 1540 m/s × 0.5 μs = 0.77 mm. Axial resolution is half the spatial pulse length, approximately 0.39 mm.

  80. Question 80Ultrasound physics and instrumentation

    A 2 MHz probe insonates blood at 0° with a velocity of 0.75 m/s. The Doppler shift is approximately:

    1. 975 Hz
    2. 7500 Hz
    3. 1950 Hz Correct answer.
    4. 3900 Hz

    Explanation

    The Doppler shift is Δf = 2 f₀ v cosθ / c. Substituting 2 × 2,000,000 Hz × 0.75 m/s × 1 / 1540 m/s gives about 1950 Hz.

  81. Question 81Two-dimensional, M-mode, and Doppler acquisition technique

    In the parasternal long-axis view, which cardiac structure lies most anteriorly, closest to the transducer?

    1. Right ventricular outflow tract Correct answer.
    2. Descending thoracic aorta
    3. Coronary sinus
    4. Left atrium

    Explanation

    In the parasternal long-axis view, the right ventricular outflow tract is the most anterior cardiac structure, lying immediately beneath the chest wall. The aortic root and left atrium are posterior to it, and the descending aorta is seen as a posterior circular structure.

  82. Question 82Two-dimensional, M-mode, and Doppler acquisition technique

    To acquire an apical four-chamber view, the transducer is placed at which location?

    1. Apical impulse Correct answer.
    2. Subxiphoid window
    3. Left parasternal border
    4. Suprasternal notch

    Explanation

    Apical views are obtained by placing the transducer at the apical impulse, with the ultrasound beam directed toward the cardiac base. This orientation places the ventricular apex at the top of the display and the atria at the bottom.

  83. Question 83Two-dimensional, M-mode, and Doppler acquisition technique

    For standard M-mode measurement of left ventricular end-diastolic and end-systolic dimensions, the cursor is best positioned at which level?

    1. At the mitral leaflet tips and chordae Correct answer.
    2. At the pulmonary valve
    3. At the tricuspid annulus
    4. At the aortic valve leaflets

    Explanation

    Standard left ventricular M-mode dimensions are measured at the chordal level just beyond the mitral leaflet tips. The cursor should be perpendicular to the left ventricular long axis to avoid oblique measurements.

  84. Question 84Two-dimensional, M-mode, and Doppler acquisition technique

    Color Doppler echocardiography primarily provides which information?

    1. Valve leaflet morphology
    2. Direction and presence of blood flow Correct answer.
    3. Chamber wall thickness
    4. Myocardial strain

    Explanation

    Color Doppler superimposes flow information on the two-dimensional image, showing the presence and direction of blood flow relative to the transducer. It does not directly measure wall thickness, leaflet morphology, or myocardial strain.

  85. Question 85Two-dimensional, M-mode, and Doppler acquisition technique

    Which advantage does continuous-wave Doppler have over pulsed-wave Doppler?

    1. It provides depth-specific flow sampling
    2. It is unaffected by transducer angle
    3. It avoids aliasing at high velocities Correct answer.
    4. It uses a smaller sample volume

    Explanation

    Continuous-wave Doppler uses separate transmitting and receiving crystals, so it records flow along the entire cursor without a range gate and does not alias at high velocities. Pulsed-wave Doppler has depth selectivity but is limited by the Nyquist limit.

  86. Question 86Two-dimensional, M-mode, and Doppler acquisition technique

    Which view is most suitable for measuring the proximal ascending aorta?

    1. Parasternal long-axis Correct answer.
    2. Subcostal four-chamber
    3. Apical four-chamber
    4. Suprasternal notch

    Explanation

    The parasternal long-axis view displays the aortic root and proximal ascending aorta in a plane suitable for diameter measurement. The suprasternal view is used for the aortic arch, while apical and subcostal views are not primary windows for the ascending aorta.

  87. Question 87Two-dimensional, M-mode, and Doppler acquisition technique

    Compared with two-dimensional imaging, M-mode echocardiography provides which main advantage?

    1. Three-dimensional reconstruction
    2. Higher temporal resolution Correct answer.
    3. Wider field of view
    4. Color flow mapping

    Explanation

    M-mode records motion along a single cursor line at a very high sampling rate, giving excellent temporal resolution for rapidly moving structures. Its field of view is limited to that one line.

  88. Question 88Two-dimensional, M-mode, and Doppler acquisition technique

    To minimize velocity underestimation by the Doppler equation, the angle between the ultrasound beam and blood flow should be kept below approximately what value?

    1. 20 degrees Correct answer.
    2. 90 degrees
    3. 45 degrees
    4. 60 degrees

    Explanation

    The Doppler shift is proportional to the cosine of the angle between the beam and flow. Keeping the angle at or below about 20 degrees limits the underestimation to less than roughly 6%.

  89. Question 89Two-dimensional, M-mode, and Doppler acquisition technique

    In pulsed-wave Doppler, the sample volume is positioned at what location?

    1. At a specific depth selected by the operator Correct answer.
    2. Beyond the Nyquist limit
    3. Along the entire length of the cursor
    4. At the transducer face

    Explanation

    Pulsed-wave Doppler uses a range gate to sample flow at a selected depth along the cursor. This provides depth specificity but also imposes a Nyquist limit on the measurable velocity.

  90. Question 90Two-dimensional, M-mode, and Doppler acquisition technique

    The Nyquist limit for pulsed-wave Doppler equals which value?

    1. The pulse repetition frequency
    2. Half the pulse repetition frequency Correct answer.
    3. Four times the pulse repetition frequency
    4. Twice the pulse repetition frequency

    Explanation

    The Nyquist limit is half the pulse repetition frequency. Velocities above this limit are displayed on the opposite side of the baseline, a phenomenon called aliasing.

  91. Question 91Two-dimensional, M-mode, and Doppler acquisition technique

    Which adjustment is most likely to reduce aliasing on a pulsed-wave Doppler tracing?

    1. Decreasing the Doppler gain
    2. Decreasing the pulse repetition frequency
    3. Increasing the wall filter
    4. Increasing the pulse repetition frequency Correct answer.

    Explanation

    Aliasing occurs when velocity exceeds the Nyquist limit, which is half the pulse repetition frequency. Increasing the pulse repetition frequency raises the Nyquist limit and reduces aliasing.

  92. Question 92Two-dimensional, M-mode, and Doppler acquisition technique

    When switching from blood-flow Doppler to tissue Doppler imaging of the mitral annulus, which setting change is appropriate?

    1. Increase the velocity scale
    2. Increase the wall filter
    3. Increase the sample volume depth
    4. Lower the velocity scale Correct answer.

    Explanation

    Tissue Doppler signals arise from low-velocity, high-amplitude myocardial motion. The velocity scale is reduced and the wall filter is lowered to capture these signals.

  93. Question 93Two-dimensional, M-mode, and Doppler acquisition technique

    In the parasternal short-axis view at the aortic valve level, the closed aortic valve in diastole is often described as which sign?

    1. Fish-mouth opening
    2. Smoke stack appearance
    3. D-shaped left ventricle
    4. Mercedes-Benz sign Correct answer.

    Explanation

    The closed aortic valve in short axis shows three cusps meeting in the center, resembling the Mercedes-Benz emblem. The fish-mouth appearance describes the mitral valve in short axis, and a D-shaped left ventricle suggests right ventricular pressure or volume overload.

  94. Question 94Two-dimensional, M-mode, and Doppler acquisition technique

    The subcostal acoustic window is especially useful in which clinical situation?

    1. A patient with a narrow intercostal space
    2. A patient with chronic obstructive pulmonary disease Correct answer.
    3. A patient with a prosthetic mitral valve
    4. A patient with an apical aneurysm

    Explanation

    The subcostal window uses the liver as an acoustic window and is often superior in patients with hyperinflated lungs from chronic obstructive pulmonary disease. It is less dependent on intercostal access than parasternal views.

  95. Question 95Two-dimensional, M-mode, and Doppler acquisition technique

    The suprasternal notch view is primarily used to evaluate which structure?

    1. The mitral valve
    2. The left ventricular apex
    3. The aortic arch Correct answer.
    4. The coronary sinus

    Explanation

    From the suprasternal notch, the beam is directed inferiorly to profile the aortic arch and its branches. This window is also used for descending aortic flow assessment.

  96. Question 96Two-dimensional, M-mode, and Doppler acquisition technique

    Which acquisition change will increase the two-dimensional frame rate?

    1. Increasing the imaging depth
    2. Narrowing the sector angle Correct answer.
    3. Increasing the color box width
    4. Increasing the number of focal zones

    Explanation

    Frame rate depends on the number of scan lines and the time needed to acquire them. Narrowing the sector angle reduces the number of lines per frame and therefore increases frame rate.

  97. Question 97Two-dimensional, M-mode, and Doppler acquisition technique

    Axial resolution in two-dimensional echocardiography is improved most by which factor?

    1. Using a lower-frequency transducer
    2. Using a higher-frequency transducer Correct answer.
    3. Increasing the sector width
    4. Increasing the display depth

    Explanation

    Axial resolution depends primarily on the spatial pulse length, which shortens as transducer frequency increases. Higher-frequency transducers provide better axial resolution but less penetration.

  98. Question 98Two-dimensional, M-mode, and Doppler acquisition technique

    On a spectral Doppler display, shifting the baseline primarily changes which aspect?

    1. The sample volume depth
    2. The pulse repetition frequency
    3. The displayed velocity range Correct answer.
    4. The wall filter setting

    Explanation

    Baseline shift moves the zero-velocity line up or down on the display, changing the displayed velocity range without changing the actual flow velocities. It is commonly used to fit high-velocity signals on the screen.

  99. Question 99Two-dimensional, M-mode, and Doppler acquisition technique

    For measurement of left ventricular outflow tract velocity, the pulsed-wave Doppler sample volume is placed at which location?

    1. In the descending aorta
    2. Just proximal to the aortic valve Correct answer.
    3. In the left ventricular apex
    4. At the aortic valve leaflet tips

    Explanation

    Left ventricular outflow tract velocity is sampled a few millimeters proximal to the aortic valve, where flow is laminar and the cursor can be aligned parallel to flow. Sampling at the leaflet tips risks recording higher, more turbulent aortic valve flow.

  100. Question 100Two-dimensional, M-mode, and Doppler acquisition technique

    Which apical view best aligns the Doppler cursor parallel to left ventricular outflow tract flow?

    1. Apical five-chamber Correct answer.
    2. Apical two-chamber
    3. Subcostal four-chamber
    4. Apical four-chamber

    Explanation

    The apical five-chamber view adds the aortic valve and proximal outflow tract to the four-chamber plane, allowing the Doppler cursor to be aligned parallel to outflow. This minimizes angle-related velocity underestimation.

  101. Question 101Two-dimensional, M-mode, and Doppler acquisition technique

    The continuity equation for aortic valve area uses which pair of Doppler measurements?

    1. Mitral annular tissue Doppler and pulmonary vein tissue Doppler
    2. Mitral inflow pulsed-wave Doppler and pulmonary vein pulsed-wave Doppler
    3. Left ventricular outflow tract pulsed-wave Doppler and aortic valve continuous-wave Doppler Correct answer.
    4. Tricuspid continuous-wave Doppler and inferior vena cava M-mode

    Explanation

    The continuity equation equates flow volume through the left ventricular outflow tract with flow through the aortic valve. It combines the outflow tract pulsed-wave velocity-time integral and diameter with the aortic valve continuous-wave velocity-time integral.

  102. Question 102Two-dimensional, M-mode, and Doppler acquisition technique

    In color Doppler imaging, a variance map is used to display which flow characteristic?

    1. Acceleration time
    2. Flow turbulence Correct answer.
    3. Mean velocity
    4. Flow power

    Explanation

    A variance map displays the dispersion of velocities within a sample, which corresponds to turbulence or disturbed flow. A mean velocity map, by contrast, shows direction and average speed of flow.

  103. Question 103Two-dimensional, M-mode, and Doppler acquisition technique

    Which combination of changes will increase the Nyquist limit during pulsed-wave Doppler?

    1. Decreasing imaging depth and increasing pulse repetition frequency Correct answer.
    2. Decreasing transducer frequency and widening the sector
    3. Increasing imaging depth and decreasing pulse repetition frequency
    4. Increasing wall filter and decreasing Doppler gain

    Explanation

    The Nyquist limit equals half the pulse repetition frequency, and pulse repetition frequency rises as imaging depth decreases. Therefore, reducing depth while increasing pulse repetition frequency raises the Nyquist limit.

  104. Question 104Two-dimensional, M-mode, and Doppler acquisition technique

    Which factor most affects the accuracy of M-mode left ventricular dimension measurements?

    1. Electrocardiographic lead selected
    2. Sweep speed of the display
    3. Color Doppler gain
    4. Alignment of the cursor perpendicular to the left ventricular long axis Correct answer.

    Explanation

    M-mode measurements assume the cursor passes through the true minor axis of the ventricle. An oblique cursor overestimates dimensions, so perpendicular alignment with the left ventricular long axis is critical.

  105. Question 105Two-dimensional, M-mode, and Doppler acquisition technique

    Which statement correctly describes continuous-wave Doppler acquisition?

    1. It requires placement of a sample volume at a specific depth
    2. It records the highest velocities along the cursor Correct answer.
    3. It provides range resolution along the cursor
    4. It is limited by the Nyquist limit

    Explanation

    Continuous-wave Doppler continuously transmits and receives along the entire cursor, so it records the highest velocities encountered anywhere along that line. Because it lacks a range gate, it has no depth resolution and does not alias at the Nyquist limit.

  106. Question 106Two-dimensional, M-mode, and Doppler acquisition technique

    A patient's body habitus limits ultrasound penetration. Compared with a 5 MHz transducer, imaging with a 2.5 MHz transducer will produce which result?

    1. Reduced axial resolution with reduced penetration
    2. Improved axial resolution with greater penetration
    3. Improved axial resolution with reduced penetration
    4. Reduced axial resolution with greater penetration Correct answer.

    Explanation

    Axial resolution depends on spatial pulse length, so a lower transmit frequency and longer wavelength degrade it. Lower frequencies are attenuated less in tissue, so the beam reaches greater depth. Probe selection follows the rule of using the highest frequency that still penetrates to the structure of interest.

  107. Question 107Two-dimensional, M-mode, and Doppler acquisition technique

    A parasternal view is obscured by lung interference. Which maneuver is most likely to improve the image?

    1. Having the patient hold a deep inspiration
    2. Imaging during a sustained Valsalva maneuver
    3. Turning the patient into a right lateral decubitus position
    4. Turning the patient into a left lateral decubitus position Correct answer.

    Explanation

    Left lateral decubitus positioning rotates the heart anteriorly against the chest wall and moves lung tissue out of the parasternal acoustic window. Full inspiration expands the lungs and tends to worsen parasternal access. Positioning is a first-line fix before adjusting machine settings.

  108. Question 108Two-dimensional, M-mode, and Doppler acquisition technique

    Which control raises the brightness of the entire two-dimensional image uniformly at all depths?

    1. Dynamic range
    2. Overall two-dimensional gain Correct answer.
    3. Time-gain compensation
    4. Depth setting

    Explanation

    Overall gain applies a single amplification factor to all returning echoes regardless of depth. Time-gain compensation instead adjusts amplification selectively by depth to correct for attenuation. Dynamic range controls how the echo amplitudes are compressed into gray shades rather than overall brightness.

  109. Question 109Two-dimensional, M-mode, and Doppler acquisition technique

    On a conventional M-mode display, what does the vertical axis represent?

    1. Distance from the transducer Correct answer.
    2. Elapsed time within the cardiac cycle
    3. Doppler frequency shift
    4. Blood flow velocity

    Explanation

    M-mode records the position of reflectors along a single cursor line as a function of time, so depth is plotted vertically and time horizontally. Motion of structures toward and away from the transducer appears as vertical displacement of the tracing.

  110. Question 110Two-dimensional, M-mode, and Doppler acquisition technique

    Narrowing the color Doppler sector width while keeping depth constant will have which effect?

    1. It increases the color frame rate Correct answer.
    2. It decreases the color frame rate
    3. It has no effect because color frame rate depends only on depth
    4. It increases the Nyquist limit of the color map

    Explanation

    Each frame requires a fixed time per scan line, so reducing the number of color lines by narrowing the box shortens frame construction time and raises the color frame rate. Depth influences frame rate as well, but the improvement still occurs when depth is unchanged. This is why a small, targeted color box is preferred.

  111. Question 111Two-dimensional, M-mode, and Doppler acquisition technique

    A high-pass wall filter on a spectral Doppler tracing serves which purpose?

    1. To improve axial resolution
    2. To increase the Nyquist limit
    3. To remove low-velocity signals from moving tissue Correct answer.
    4. To shorten the length of the Doppler sample volume

    Explanation

    Wall filters reject Doppler shifts below a chosen threshold, suppressing the strong, low-velocity signals from myocardium and valve leaflets that would otherwise obscure the blood flow spectrum. Setting the filter too high can also strip genuine low-velocity flow from the display.

  112. Question 112Two-dimensional, M-mode, and Doppler acquisition technique

    Increasing the spectral Doppler gain well beyond the optimal level produces which artifact?

    1. A shift of the displayed baseline
    2. Loss of the spectral envelope with a faint tracing
    3. Aliasing of the peak velocities
    4. Spectral broadening from background noise Correct answer.

    Explanation

    Excessive gain amplifies electronic noise across the spectrum, filling in the clear window beneath the waveform and artificially broadening the trace. Gain should be reduced until the envelope is crisp while faint genuine signals remain visible. Gain never corrects aliasing or baseline position.

  113. Question 113Two-dimensional, M-mode, and Doppler acquisition technique

    Compared with fundamental imaging, tissue harmonic imaging improves endocardial border definition mainly by which mechanism?

    1. Reducing clutter and reverberation artifacts Correct answer.
    2. Widening the sector angle to include more anatomy
    3. Increasing the transmitted frequency to improve penetration
    4. Increasing the frame rate of the two-dimensional image

    Explanation

    Harmonic energy at twice the transmitted frequency is generated within tissue and builds up preferentially along the main beam, so side-lobe and reverberation clutter is relatively suppressed. The result is cleaner cavity-to-wall interfaces and better border delineation, especially in technically difficult patients.

  114. Question 114Two-dimensional, M-mode, and Doppler acquisition technique

    When optimizing a parasternal long-axis image for measuring the aortic valve leaflets, where should the transmit focal zone be placed?

    1. Focal position does not affect image quality
    2. At the depth of the aortic valve Correct answer.
    3. At the top of the sector, near the transducer
    4. At the bottom of the sector, beyond the valve

    Explanation

    The ultrasound beam is narrowest at the transmit focus, producing the best lateral resolution at that depth. Placing the focus at the level of the valve sharpens the leaflets for measurement. Focusing elsewhere leaves the beam wider at the target depth.

  115. Question 115Two-dimensional, M-mode, and Doppler acquisition technique

    Increasing the length of the pulsed-wave Doppler sample volume produces which effect?

    1. A higher Nyquist limit
    2. Spectral broadening of the trace Correct answer.
    3. Improved range resolution along the beam
    4. A higher Doppler shift frequency

    Explanation

    A longer gate interrogates a greater depth range, so a wider spread of flow velocities is included and the spectrum broadens. A short gate improves selectivity for a specific location but may reduce signal strength. Gate length is therefore chosen according to the structure being sampled.

  116. Question 116Two-dimensional, M-mode, and Doppler acquisition technique

    During color Doppler interrogation of mitral inflow, the display shows a mosaic of red and blue within the jet. Which adjustment is most appropriate?

    1. Decrease the color velocity scale
    2. Move the color box deeper
    3. Increase the color velocity scale Correct answer.
    4. Increase the color gain

    Explanation

    The mixture of colors indicates aliasing because the velocity scale is set below the peak velocity of the jet. Raising the scale, or shifting the color baseline, moves the peak within the display range and removes the wrap-around. Gain is adjusted only after the scale is appropriate.

  117. Question 117Two-dimensional, M-mode, and Doppler acquisition technique

    Increasing the sweep speed of a spectral Doppler display results in which change?

    1. Waveforms are displayed across a wider horizontal span Correct answer.
    2. The sample volume shifts to a shallower depth
    3. The peak velocity measures higher than before
    4. The Nyquist limit is reduced

    Explanation

    Sweep speed determines how much time is compressed onto the horizontal axis; a faster sweep spreads events over a greater distance, making timing and duration easier to appreciate. It is purely a display function and does not alter the recorded velocities or the Doppler physics.

  118. Question 118Two-dimensional, M-mode, and Doppler acquisition technique

    In pulsed-wave Doppler, increasing the depth of the sample volume has which effect on the highest pulse repetition frequency that can be used without range ambiguity?

    1. It increases the maximum PRF and raises the Nyquist limit
    2. It has no effect on PRF because PRF is set by the transducer frequency
    3. It increases the maximum PRF but leaves the Nyquist limit unchanged
    4. It decreases the maximum PRF and lowers the Nyquist limit Correct answer.

    Explanation

    Each pulse must travel to the sample volume and back before the next pulse is emitted, so the maximum PRF is approximately the speed of sound divided by twice the depth. Deeper sampling therefore lowers the allowable PRF, and because the Nyquist limit is half the PRF, aliasing becomes more likely at depth.

  119. Question 119Two-dimensional, M-mode, and Doppler acquisition technique

    Which statement best distinguishes write zoom from read zoom?

    1. Write zoom simply magnifies the stored image without new data
    2. Write zoom reacquires the region of interest with more lines Correct answer.
    3. Read zoom increases the frame rate of the acquisition
    4. Read zoom acquires extra lines within a small region

    Explanation

    Write zoom acts during acquisition: the system rescans a smaller region of interest with a higher line density, so pixel density and spatial resolution are preserved or improved. Read zoom is a post-processing magnification of already stored data and adds no new information.

  120. Question 120Two-dimensional, M-mode, and Doppler acquisition technique

    Slice thickness (elevational) resolution in two-dimensional echocardiography is determined primarily by which factor?

    1. The dynamic range setting
    2. The overall receiver gain
    3. The transmit focal zone position
    4. The transducer element height and acoustic lens Correct answer.

    Explanation

    Slice thickness is governed by the height of the transducer aperture and its fixed elevational lens, making it a property of probe design rather than an adjustable setting. Focusing within the scan plane refines lateral resolution in that plane but does not narrow the slice. This is why structures may appear to merge when they lie at different elevations.

  121. Question 121Valvular heart disease and hemodynamics

    In the continuity equation used to calculate aortic valve area, which term appears in the numerator?

    1. Aortic valve area multiplied by mean transvalvular gradient
    2. Aortic valve velocity-time integral multiplied by the heart rate at the time of the study
    3. LVOT cross-sectional area multiplied by LVOT velocity-time integral Correct answer.
    4. LVOT diameter multiplied by peak aortic jet velocity

    Explanation

    Flow through the LVOT equals flow through the stenotic orifice, so stroke volume (LVOT area × LVOT VTI) is divided by the aortic valve VTI to yield valve area. The LVOT area is derived from a measured diameter assuming a circular cross-section.

  122. Question 122Valvular heart disease and hemodynamics

    Which peak continuous-wave Doppler velocity is consistent with severe aortic stenosis?

    1. 4.2 m/s Correct answer.
    2. 2.0 m/s
    3. 3.0 m/s
    4. 2.8 m/s

    Explanation

    Severe aortic stenosis is defined by a peak velocity of 4.0 m/s or greater when stroke volume is normal. Velocities from 3.0 to 3.9 m/s indicate moderate disease, and values below 3.0 m/s indicate mild disease.

  123. Question 123Valvular heart disease and hemodynamics

    A mitral valve pressure half-time of 220 ms corresponds to an estimated mitral valve area of approximately:

    1. 0.5 cm²
    2. 1.0 cm² Correct answer.
    3. 1.5 cm²
    4. 2.0 cm²

    Explanation

    Mitral valve area by the half-time method is calculated as 220 divided by the pressure half-time in milliseconds. A half-time of 220 ms therefore gives an area of about 1.0 cm², which lies in the severe range.

  124. Question 124Valvular heart disease and hemodynamics

    Which Doppler finding is a specific sign of severe aortic regurgitation?

    1. A short and faint regurgitant jet seen on colour Doppler imaging
    2. Antegrade diastolic flow in the descending aorta
    3. Peak aortic regurgitant velocity of 2.5 m/s
    4. Holodiastolic flow reversal in the descending aorta Correct answer.

    Explanation

    Severe aortic regurgitation reverses flow throughout diastole in the descending and abdominal aorta, and an end-diastolic reversal velocity above 20 cm/s supports severity. Jet velocity reflects the diastolic pressure difference between aorta and left ventricle, not the regurgitant volume.

  125. Question 125Valvular heart disease and hemodynamics

    LVOT velocity-time integral is 20 cm and the aortic valve velocity-time integral is 80 cm. The dimensionless index is:

    1. 0.75
    2. 4.00
    3. 0.50
    4. 0.25 Correct answer.

    Explanation

    The dimensionless index is the LVOT velocity-time integral divided by the aortic valve velocity-time integral, here 20 divided by 80. A value of 0.25 or less is consistent with severe stenosis and, unlike valve area, is not affected by body size.

  126. Question 126Valvular heart disease and hemodynamics

    Mitral regurgitant effective orifice area by the proximal isovelocity surface area method is calculated as:

    1. 2πr² × Vmax(MR) / Valiasing
    2. 2πr² × Valiasing / Vmax(MR) Correct answer.
    3. 2πr × Valiasing / Vmax(MR)
    4. πr² × Vmax(MR) / Valiasing

    Explanation

    Flow through the hemispheric shell equals 2πr² multiplied by the aliasing velocity, and dividing this flow by the peak regurgitant velocity gives the effective orifice area. The radius is measured from the shell to the valve plane at the first aliasing.

  127. Question 127Valvular heart disease and hemodynamics

    Which vena contracta width is most consistent with severe mitral regurgitation?

    1. 0.2 cm
    2. 0.8 cm Correct answer.
    3. 0.4 cm
    4. 0.5 cm

    Explanation

    Severe mitral regurgitation corresponds to a vena contracta width of 0.7 cm or more, while 0.3 to 0.6 cm indicates moderate disease. The measurement is taken at the narrowest neck of the jet using a narrow colour sector and an optimized Nyquist limit.

  128. Question 128Valvular heart disease and hemodynamics

    Systolic flow reversal in the pulmonary veins on pulsed-wave Doppler is most consistent with:

    1. Mild mitral regurgitation
    2. Severe tricuspid regurgitation
    3. Severe mitral regurgitation Correct answer.
    4. Normal pulmonary venous flow

    Explanation

    In severe mitral regurgitation the regurgitant volume raises left atrial pressure enough during systole to reverse pulmonary venous inflow. Milder degrees of regurgitation blunt or reduce the systolic wave but do not reverse it.

  129. Question 129Valvular heart disease and hemodynamics

    Peak tricuspid regurgitation velocity is 3.5 m/s and right atrial pressure is estimated at 10 mmHg. The right ventricular systolic pressure is approximately:

    1. 24 mmHg
    2. 59 mmHg Correct answer.
    3. 35 mmHg
    4. 49 mmHg

    Explanation

    Right ventricular systolic pressure equals 4 times the square of the TR velocity plus the right atrial pressure. Four times 3.5 squared is 49 mmHg, and adding 10 mmHg gives about 59 mmHg in the absence of pulmonary stenosis.

  130. Question 130Valvular heart disease and hemodynamics

    Pressure half-time derived mitral valve area is least reliable in the presence of:

    1. Significant aortic regurgitation Correct answer.
    2. Mild left atrial enlargement
    3. Sinus rhythm at 70 beats per minute
    4. Trace tricuspid regurgitation

    Explanation

    The half-time method assumes a stable relationship between the transmitral gradient and the rate of deceleration, which is altered when left ventricular or atrial compliance changes. Significant aortic regurgitation and the period immediately after balloon valvotomy are classic confounders.

  131. Question 131Valvular heart disease and hemodynamics

    A patient with LVEF 25%, aortic valve area 0.8 cm², and mean gradient 22 mmHg undergoes dobutamine stress. Stroke volume rises, the gradient increases to 38 mmHg, and the valve area remains 0.7 cm². This response indicates:

    1. Pseudo-severe aortic stenosis
    2. Normal aortic valve function
    3. True severe aortic stenosis Correct answer.
    4. Moderate aortic stenosis

    Explanation

    With true severe stenosis the increased flow raises the gradient while the fixed orifice stays small, generally below 1.0 cm². A pseudo-severe valve recruits area above 1.0 cm² as flow increases, so the gradient rises little relative to the flow change.

  132. Question 132Valvular heart disease and hemodynamics

    Paradoxical low-flow, low-gradient severe aortic stenosis is characterized by:

    1. Normal LVEF with a high mean gradient and a normal stroke volume index
    2. High stroke volume index with a low gradient
    3. Reduced LVEF with a high mean gradient
    4. Preserved LVEF, low stroke volume index, and a low mean gradient Correct answer.

    Explanation

    Paradoxical low flow describes a small calculated valve area with a low gradient despite a preserved ejection fraction, usually reflecting a small, concentrically remodeled ventricle with reduced stroke volume. Severity is confirmed when the area remains 1.0 cm² or less after correcting for flow.

  133. Question 133Valvular heart disease and hemodynamics

    When Doppler flow assumptions are unreliable, the preferred alternative for quantifying aortic valve area is:

    1. Mean transvalvular gradient alone
    2. Direct planimetry of the anatomic orifice Correct answer.
    3. The dimensionless index
    4. Peak aortic jet velocity alone

    Explanation

    Planimetry of the anatomic orifice by two- or three-dimensional imaging does not depend on flow or pressure gradients. It measures the anatomic rather than the physiologic orifice, so it tends to slightly overestimate the effective area.

  134. Question 134Valvular heart disease and hemodynamics

    An aortic regurgitation pressure half-time of 180 ms is most consistent with:

    1. Severe aortic regurgitation Correct answer.
    2. Mild aortic regurgitation
    3. Moderate aortic regurgitation
    4. A normal aortic valve

    Explanation

    A short pressure half-time below 200 ms indicates rapid equalization of aortic and left ventricular diastolic pressures, which occurs in severe regurgitation. Values above 500 ms are typical of mild disease.

  135. Question 135Valvular heart disease and hemodynamics

    Which feature is scored in the Wilkins echocardiographic score for mitral stenosis?

    1. Mitral annular calcification
    2. Left atrial diameter
    3. Pulmonary vein systolic fraction
    4. Leaflet mobility Correct answer.

    Explanation

    The Wilkins score grades leaflet mobility, leaflet thickening, calcification, and subvalvular thickening, each from 1 to 4, for a maximum of 16. Lower scores predict a better result from balloon mitral valvotomy.

  136. Question 136Valvular heart disease and hemodynamics

    The mean diastolic gradient across a normally functioning mechanical mitral valve is generally:

    1. 10 to 15 mmHg
    2. 15 to 20 mmHg
    3. 5 to 10 mmHg
    4. 5 mmHg or less Correct answer.

    Explanation

    Prosthetic valves are inherently obstructive, but a normally functioning mechanical mitral prosthesis usually has a mean gradient of 5 mmHg or less at normal heart rates. Higher gradients suggest obstruction, thrombosis, or high transvalvular flow.

  137. Question 137Valvular heart disease and hemodynamics

    Using the Gorlin equation with a cardiac output of 5 L/min, heart rate 80/min, systolic ejection period 0.3 s, and mean gradient 50 mmHg, the aortic valve area is approximately:

    1. 1.3 cm²
    2. 0.4 cm²
    3. 0.7 cm² Correct answer.
    4. 1.0 cm²

    Explanation

    Aortic valve area equals cardiac output in mL/min divided by heart rate times systolic ejection period times 44.3 times the square root of the mean gradient. Here 5000 divided by (80 × 0.3 × 44.3 × 7.07) gives approximately 0.67 cm².

  138. Question 138Valvular heart disease and hemodynamics

    The largest source of error in continuity-equation aortic valve area is:

    1. Measurement of the mean gradient
    2. The heart rate at the time of the study
    3. Measurement of the aortic valve velocity-time integral
    4. Measurement of the LVOT diameter Correct answer.

    Explanation

    Because LVOT area depends on the square of the radius, a small error in the diameter is squared and then propagated through the entire calculation. Averaging several measurements and measuring at the annulus improve accuracy.

  139. Question 139Valvular heart disease and hemodynamics

    In severe tricuspid regurgitation, the peak TR velocity may underestimate right ventricular systolic pressure because:

    1. The right atrial pressure is always low
    2. The regurgitant jet velocity is unrelated to the pressure gradient
    3. The jet is best recorded only from the apical four-chamber view
    4. Rapid equalization of right ventricular and atrial pressures Correct answer.

    Explanation

    Right ventricular systolic pressure is derived from the maximal right ventricular to right atrial pressure difference. With severe regurgitation the pressures equalize early in systole, so the peak gradient and the calculated pressure are falsely low despite elevated right-sided pressures.

  140. Question 140Valvular heart disease and hemodynamics

    Which mitral regurgitant volume is consistent with severe mitral regurgitation?

    1. 15 mL
    2. 30 mL
    3. 70 mL Correct answer.
    4. 45 mL

    Explanation

    Severe mitral regurgitation is defined by a regurgitant volume of 60 mL or more, a regurgitant fraction of 50% or more, and an effective orifice area of at least 0.4 cm². Values below these thresholds indicate less severe disease.

  141. Question 141Valvular heart disease and hemodynamics

    When measuring peak aortic jet velocity in aortic stenosis, the sonographer should:

    1. Use continuous-wave Doppler exclusively from the subcostal window
    2. Use whichever window yields the highest velocity Correct answer.
    3. Use the apical four-chamber window only
    4. Use pulsed-wave Doppler at the valve tips

    Explanation

    The highest achievable velocity best reflects the maximal gradient, so multiple windows are interrogated with continuous-wave Doppler, most often the apical five-chamber and right parasternal views. Pulsed-wave Doppler aliases at the high velocities encountered in stenosis.

  142. Question 142Valvular heart disease and hemodynamics

    Which finding indicates severe rather than moderate mitral stenosis?

    1. Mitral valve area of 0.9 cm² Correct answer.
    2. Peak E velocity of 1.2 m/s
    3. Mean diastolic gradient of 4 mmHg
    4. Pressure half-time of 150 ms

    Explanation

    Severe mitral stenosis is defined by a valve area of 1.0 cm² or less, with a mean gradient that is usually 10 mmHg or more at normal heart rates. A half-time of 150 ms corresponds to an area near 1.5 cm², which is not severe.

  143. Question 143Valvular heart disease and hemodynamics

    An aortic regurgitation jet width that is 65% of the LVOT width indicates:

    1. Severe regurgitation Correct answer.
    2. Trivial regurgitation
    3. Moderate regurgitation
    4. Mild regurgitation

    Explanation

    A jet width to LVOT width ratio of 65% or more is a simple semiquantitative sign of severe aortic regurgitation. Ratios below 25% suggest mild disease, and values from 25% to 64% suggest moderate disease.

  144. Question 144Valvular heart disease and hemodynamics

    Contractile reserve during dobutamine stress echocardiography in low-flow, low-gradient aortic stenosis is defined as:

    1. An increase in aortic valve area of at least 0.3 cm²
    2. An increase in stroke volume of at least 20% Correct answer.
    3. An increase in mean gradient of at least 10 mmHg
    4. A decrease in LVOT velocity-time integral

    Explanation

    Contractile reserve refers to a flow increase, reflected by stroke volume, of 20% or more during dobutamine infusion. Its presence improves the reliability of the stress study and identifies patients who tolerate valve replacement better.

  145. Question 145Valvular heart disease and hemodynamics

    Pressure recovery causes Doppler-derived aortic valve gradients to:

    1. Match the catheter gradient exactly
    2. Overestimate the catheter gradient in small aortas Correct answer.
    3. Eliminate the need for valve area calculation
    4. Underestimate the gradient obtained at catheterization

    Explanation

    Downstream of a stenosis, kinetic energy is partly reconverted into pressure, so a catheter distal to the valve records a higher pressure than Doppler predicts. The discrepancy is greatest in small aortas with mild to moderate stenosis.

  146. Question 146Valvular heart disease and hemodynamics

    Using the simplified Bernoulli equation, a peak aortic jet velocity of 3.0 m/s corresponds to a peak instantaneous gradient of:

    1. 18 mmHg
    2. 72 mmHg
    3. 9 mmHg
    4. 36 mmHg Correct answer.

    Explanation

    The simplified Bernoulli equation estimates peak instantaneous gradient as 4v², where v is the peak velocity in m/s. For v = 3.0 m/s, 4 × 9 = 36 mmHg. This is a peak instantaneous gradient, not a mean gradient.

  147. Question 147Valvular heart disease and hemodynamics

    A normal aortic valve area in an adult is approximately:

    1. 4.5 to 5.5 cm²
    2. 1.5 to 2.0 cm²
    3. 0.5 to 1.0 cm²
    4. 3.0 to 4.0 cm² Correct answer.

    Explanation

    A normal adult aortic valve area is approximately 3.0 to 4.0 cm². Values below 1.0 cm² indicate severe aortic stenosis, and intermediate values suggest mild or moderate narrowing.

  148. Question 148Valvular heart disease and hemodynamics

    A vena contracta width of 0.7 cm in the aortic regurgitation jet is most consistent with:

    1. mild aortic regurgitation
    2. moderate aortic regurgitation
    3. severe aortic regurgitation Correct answer.
    4. trivial aortic regurgitation

    Explanation

    Severe aortic regurgitation is suggested by a vena contracta width of at least 0.6 cm. Mild aortic regurgitation is typically less than 0.3 cm, and moderate regurgitation is 0.3 to 0.6 cm.

  149. Question 149Valvular heart disease and hemodynamics

    Mitral valve area by pressure half-time is calculated as:

    1. MVA = 220 × PHT
    2. MVA = PHT / 220
    3. MVA = 220 + PHT
    4. MVA = 220 / PHT Correct answer.

    Explanation

    The empirically derived formula is MVA = 220 / PHT, with pressure half-time expressed in milliseconds. A longer pressure half-time indicates a smaller mitral valve area. The formula is less reliable when left atrial or left ventricular compliance changes acutely.

  150. Question 150Valvular heart disease and hemodynamics

    LVOT VTI is 15 cm and aortic valve VTI is 75 cm. The dimensionless index is:

    1. 1.33
    2. 0.25
    3. 5.0
    4. 0.20 Correct answer.

    Explanation

    The dimensionless index is the ratio of LVOT VTI to aortic valve VTI. Here 15 / 75 = 0.20. A value below 0.25 is consistent with severe aortic stenosis.

  151. Question 151Valvular heart disease and hemodynamics

    LVOT diameter is 2.0 cm, LVOT VTI is 20 cm, and aortic valve VTI is 50 cm. The continuity-equation aortic valve area is:

    1. 1.26 cm² Correct answer.
    2. 2.00 cm²
    3. 1.57 cm²
    4. 0.80 cm²

    Explanation

    LVOT area = π × (diameter / 2)² = 3.14 cm² for a 2.0-cm diameter. AVA = LVOT area × (LVOT VTI / aortic VTI) = 3.14 × 20/50 = 1.26 cm². This value is consistent with moderate aortic stenosis.

  152. Question 152Valvular heart disease and hemodynamics

    Systolic flow reversal in the hepatic veins on pulsed-wave Doppler is most consistent with:

    1. mild tricuspid regurgitation
    2. severe tricuspid regurgitation Correct answer.
    3. moderate tricuspid regurgitation
    4. tricuspid stenosis

    Explanation

    Severe tricuspid regurgitation produces systolic flow reversal in the hepatic veins because the regurgitant volume raises right atrial pressure enough to reverse systolic inflow. Mild or moderate tricuspid regurgitation usually preserves systolic forward flow. The finding is specific but not sensitive for severe regurgitation.

  153. Question 153Valvular heart disease and hemodynamics

    A prosthesis-patient mismatch is considered severe when the indexed effective orifice area is:

    1. ≤0.85 cm²/m²
    2. ≤1.2 cm²/m²
    3. ≤0.65 cm²/m² Correct answer.
    4. ≤1.0 cm²/m²

    Explanation

    Prosthesis-patient mismatch is graded by indexed effective orifice area: severe mismatch is ≤0.65 cm²/m², moderate mismatch is 0.65 to 0.85 cm²/m², and clinically insignificant mismatch is >0.85 cm²/m². Indexing to body surface area accounts for patient size.

  154. Question 154Valvular heart disease and hemodynamics

    A late-peaking, dagger-shaped continuous-wave Doppler jet across the LVOT is most characteristic of:

    1. dynamic LVOT obstruction Correct answer.
    2. valvular aortic stenosis
    3. fixed subaortic stenosis
    4. aortic regurgitation

    Explanation

    Dynamic LVOT obstruction causes a late-peaking, dagger-shaped systolic jet because the obstruction worsens as the ventricle empties. Fixed valvular or subvalvular stenosis produces a more symmetric and earlier-peaking jet. The finding is typical of hypertrophic cardiomyopathy with systolic anterior motion.

  155. Question 155Valvular heart disease and hemodynamics

    Holodiastolic flow reversal in the descending thoracic aorta is most consistent with:

    1. mild aortic regurgitation
    2. normal aortic flow
    3. severe aortic regurgitation Correct answer.
    4. moderate aortic stenosis

    Explanation

    Holodiastolic flow reversal in the descending thoracic aorta indicates that the regurgitant volume is large enough to reverse diastolic flow throughout the aorta, consistent with severe aortic regurgitation. Mild regurgitation usually shows only brief early diastolic reversal. The finding should be interpreted with other severity markers.

  156. Question 156Valvular heart disease and hemodynamics

    A mechanical mitral prosthesis shows a mean gradient of 12 mmHg and restricted leaflet motion on fluoroscopy. The most likely cause is:

    1. mild prosthetic regurgitation
    2. normal prosthetic function
    3. high cardiac output state
    4. prosthetic valve thrombosis Correct answer.

    Explanation

    An elevated mean gradient with restricted leaflet motion suggests prosthetic valve obstruction, most often thrombosis or pannus. Thrombosis is more likely with inadequate anticoagulation and may present acutely. Pannus is more chronic and often involves the hinge points.

  157. Question 157Valvular heart disease and hemodynamics

    Mitral valve area by two-dimensional planimetry should be measured:

    1. at the leaflet tips in mid-diastole Correct answer.
    2. at the commissures in systole
    3. at the mitral annulus in diastole
    4. at the leaflet tips in early systole

    Explanation

    Planimetry is performed in the parasternal short-axis view by tracing the mitral orifice at the leaflet tips in mid-diastole. Measuring at the annulus or commissures overestimates the area. Correct timing avoids underestimation from a small early-diastolic orifice.

  158. Question 158Valvular heart disease and hemodynamics

    Mitral regurgitant effective orifice area is 0.45 cm² and the mitral regurgitation VTI is 140 cm. The regurgitant volume is:

    1. 63 mL Correct answer.
    2. 6.3 mL
    3. 31 mL
    4. 16 mL

    Explanation

    Regurgitant volume is calculated as effective orifice area × mitral regurgitation VTI. Here 0.45 cm² × 140 cm = 63 mL. A regurgitant volume of at least 60 mL is consistent with severe mitral regurgitation.

  159. Question 159Valvular heart disease and hemodynamics

    In the continuity equation, a 1-mm error in measuring a 2.0-cm LVOT diameter produces an error in aortic valve area of approximately:

    1. 50%
    2. 25%
    3. 10% Correct answer.
    4. 1%

    Explanation

    Because area is proportional to diameter squared, the fractional area error is approximately twice the fractional diameter error. A 0.1-cm error on a 2.0-cm diameter is 5%, yielding about a 10% area error. This is a major source of variability in continuity-equation valve area.

  160. Question 160Valvular heart disease and hemodynamics

    Peak aortic jet velocity is 4.2 m/s, mean gradient is 32 mmHg, and aortic valve area is 0.9 cm² with normal flow. The findings are most consistent with:

    1. pseudosevere aortic stenosis
    2. severe aortic stenosis Correct answer.
    3. moderate aortic stenosis
    4. normal aortic valve function

    Explanation

    Severe aortic stenosis is defined by a peak velocity of at least 4.0 m/s, a mean gradient of at least 40 mmHg, or an aortic valve area below 1.0 cm². When peak velocity and valve area indicate severe stenosis but the mean gradient is lower, the discordance should be confirmed and interpreted in context. In this case the peak velocity and valve area support severe aortic stenosis.

  161. Question 161Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic pattern is the classic hallmark of hypertrophic cardiomyopathy?

    1. Global hypokinesis with marked left ventricular cavity dilation
    2. Apical akinesis with a thin, scarred left ventricular apex
    3. Septal-to-posterior wall thickness ratio of 1.3 or greater Correct answer.
    4. Symmetric hypertrophy with a dilated, thin-walled left ventricle

    Explanation

    Hypertrophic cardiomyopathy is defined by otherwise unexplained myocardial hypertrophy, most often asymmetric and favouring the septum, with a septal-to-posterior wall ratio of at least 1.3. The hypertrophy is usually accompanied by a small, hyperdynamic cavity rather than dilation.

  162. Question 162Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which finding best separates a pericardial effusion from a pleural effusion on echocardiography?

    1. The fluid is seen only behind the left atrium
    2. The fluid produces a systolic jet on color Doppler
    3. The fluid is seen anterior to the descending thoracic aorta Correct answer.
    4. The fluid is anechoic and varies with respiration

    Explanation

    Pericardial fluid tracks anterior to the descending thoracic aorta because the pericardial reflections enclose that region, whereas pleural fluid passes posterior to the aorta. This relationship is assessed in the parasternal long-axis view.

  163. Question 163Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which set of findings best defines dilated cardiomyopathy?

    1. Apical hypertrophy with an intracavitary gradient at rest
    2. Concentric hypertrophy with a small left ventricular cavity
    3. Normal cavity size with biatrial enlargement and preserved ejection fraction
    4. Left ventricular dilation with global systolic dysfunction and reduced ejection fraction Correct answer.

    Explanation

    Dilated cardiomyopathy is characterised by left or biventricular dilation together with global systolic impairment, usually with an ejection fraction below 45%. The walls are typically thin or normal in thickness rather than hypertrophied.

  164. Question 164Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which finding is most typical of restrictive cardiomyopathy?

    1. Marked left ventricular dilation with an ejection fraction below 30%
    2. Asymmetric septal hypertrophy with systolic anterior motion of the mitral leaflet
    3. Dense pericardial calcification with respiratory ventricular interdependence
    4. Biatrial enlargement with normal or near-normal left ventricular cavity size Correct answer.

    Explanation

    Restrictive cardiomyopathy produces impaired filling with high atrial pressures, so both atria dilate while the ventricular cavity remains normal or small. Systolic function is frequently preserved until late in the disease.

  165. Question 165Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which congenital cardiac abnormality is the most common one encountered in adults?

    1. Secundum atrial septal defect
    2. Bicuspid aortic valve Correct answer.
    3. Ebstein anomaly of the tricuspid valve
    4. Congenital pulmonary valve stenosis

    Explanation

    Bicuspid aortic valve affects roughly 1 to 2 percent of the population and is the most frequent congenital cardiac anomaly overall. Many affected adults present with aortic stenosis or regurgitation rather than with a recognised childhood diagnosis.

  166. Question 166Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A large secundum atrial septal defect typically produces which echocardiographic pattern?

    1. Right heart volume overload with a dilated right ventricle Correct answer.
    2. Left ventricular pressure overload with concentric hypertrophy
    3. A small right ventricular cavity with systolic septal flattening
    4. Left ventricular volume overload with a dilated left ventricle

    Explanation

    A left-to-right shunt at atrial level adds systemic venous return to the right atrium, so the right atrium and right ventricle dilate and the ventricular septum may show diastolic flattening. The left ventricle is not volume loaded by an uncomplicated shunt.

  167. Question 167Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic finding defines mitral valve prolapse?

    1. Systolic displacement of one or both leaflets at least 2 mm beyond the annular plane Correct answer.
    2. Diastolic doming of the anterior leaflet with commissural fusion
    3. Systolic anterior motion of the anterior leaflet with outflow tract obstruction
    4. Restricted leaflet closure with a forward mitral jet in early diastole

    Explanation

    Mitral valve prolapse is defined by systolic bowing of one or both leaflets beyond the plane of the mitral annulus by 2 mm or more, best seen in the parasternal long-axis view. Leaflet thickening and myxomatous change often accompany the displacement.

  168. Question 168Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which two-dimensional finding is most suggestive of cardiac tamponade?

    1. A large loculated effusion posterior to the left atrium
    2. Early diastolic collapse of the right ventricular free wall Correct answer.
    3. An echo-free space less than 5 mm in width
    4. Spontaneous echo contrast within the pericardial space

    Explanation

    When intrapericardial pressure exceeds right ventricular diastolic pressure, the low-pressure right ventricular free wall collapses in early diastole. Right atrial systolic collapse is an earlier but less specific sign.

  169. Question 169Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient with a moderate pericardial effusion shows a 35 percent inspiratory fall in mitral early diastolic inflow velocity on pulsed Doppler. Which condition does this pattern support?

    1. Cardiac tamponade Correct answer.
    2. Mitral stenosis
    3. Severe aortic regurgitation
    4. Restrictive cardiomyopathy

    Explanation

    Respiratory variation in mitral inflow of more than 25 percent, mirrored by reciprocal variation in tricuspid inflow, reflects exaggerated ventricular interdependence and supports tamponade physiology. The variation results from phasic changes in right and left heart filling within a fixed pericardial volume.

  170. Question 170Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic finding best supports a diagnosis of constrictive pericarditis?

    1. Marked left ventricular wall thickening with a small cavity
    2. Abrupt early diastolic septal bounce with ventricular interdependence Correct answer.
    3. Paradoxic septal motion occurring only in systole
    4. Global hypokinesis with a dilated left ventricle

    Explanation

    Rigid pericardium limits total cardiac volume, so filling of one ventricle occurs at the expense of the other, producing an abrupt early diastolic septal shift or bounce and respiratory ventricular interdependence. Septal flattening in diastole and preserved annular tissue velocities support the diagnosis.

  171. Question 171Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    During continuous-wave Doppler assessment of a patient with hypertrophic cardiomyopathy, which manoeuvre most reliably provokes a dynamic left ventricular outflow tract gradient?

    1. Valsalva strain combined with amyl nitrite inhalation Correct answer.
    2. Passive leg elevation with head-down tilt
    3. Rapid squatting
    4. Isometric handgrip sustained to fatigue

    Explanation

    Dynamic obstruction worsens when preload and afterload fall, so Valsalva strain and vasodilators such as amyl nitrite unmask or intensify the gradient. Squatting and handgrip raise preload or afterload and therefore tend to reduce it.

  172. Question 172Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Relative apical sparing of longitudinal strain, with reduced basal and mid-wall strain, is most characteristic of which condition?

    1. Constrictive pericarditis
    2. Cardiac amyloidosis Correct answer.
    3. Hypertrophic cardiomyopathy with an apical aneurysm
    4. Athlete's heart

    Explanation

    Amyloid infiltration is greatest at the base and mid wall, so longitudinal strain is impaired there while the apex is relatively spared, giving the cherry-on-top bullseye pattern. The finding is useful for distinguishing amyloidosis from other causes of hypertrophy.

  173. Question 173Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic combination favours a diagnosis of arrhythmogenic right ventricular cardiomyopathy?

    1. Biventricular hypertrophy with a restrictive filling pattern
    2. Left ventricular apical ballooning with a hyperkinetic base
    3. Right ventricular dilation with localised wall motion abnormality and a thin free wall Correct answer.
    4. Right ventricular hypertrophy with diastolic septal flattening

    Explanation

    Arrhythmogenic right ventricular cardiomyopathy is characterised by fibrofatty replacement of right ventricular myocardium, producing regional akinesis, dyskinesis or aneurysmal bulging together with right ventricular dilation. Recognition of these regional abnormalities is central to the echocardiographic diagnosis.

  174. Question 174Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A postmenopausal woman with acute chest pain shows apical akinesis with basal hyperkinesis and no obstructive coronary disease. Which diagnosis fits best?

    1. Peripartum cardiomyopathy
    2. Acute myocardial infarction from left anterior descending occlusion
    3. Takotsubo cardiomyopathy Correct answer.
    4. Cardiac amyloidosis

    Explanation

    Transient apical and mid-ventricular akinesis with compensatory basal hyperkinesis, in the absence of a culprit coronary lesion, is the typical appearance of Takotsubo cardiomyopathy. Wall motion usually recovers over days to weeks.

  175. Question 175Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A restrictive perimembranous ventricular septal defect is best characterised by which color Doppler finding?

    1. Left-to-right flow occurring only during diastole
    2. Bidirectional flow with equal systolic and diastolic velocities
    3. A broad low-velocity systolic jet that fills the right ventricle
    4. A narrow high-velocity systolic jet indicating a large interventricular pressure difference Correct answer.

    Explanation

    A small, restrictive defect maintains a large systolic pressure difference between the ventricles, so the shunt appears as a narrow, high-velocity jet on color and continuous-wave Doppler. The measured gradient can be used to estimate right ventricular systolic pressure.

  176. Question 176Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which combination of findings is typical of tetralogy of Fallot on echocardiography?

    1. Aortic override, ventricular septal defect and right ventricular outflow tract obstruction Correct answer.
    2. Atrial septal defect, left ventricular hypertrophy and pulmonary regurgitation
    3. Ventricular septal defect, left ventricular hypertrophy and aortic stenosis
    4. Aortic override, mitral atresia and a hypoplastic left ventricle

    Explanation

    Tetralogy of Fallot comprises a malalignment ventricular septal defect, an overriding aorta, right ventricular outflow tract obstruction and consequent right ventricular hypertrophy. The outflow obstruction determines the direction and degree of shunting.

  177. Question 177Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which defect is characteristically associated with a cleft anterior mitral leaflet and an ostium primum atrial septal defect?

    1. Muscular ventricular septal defect
    2. Sinus venosus atrial septal defect
    3. Partial atrioventricular septal defect Correct answer.
    4. Secundum atrial septal defect

    Explanation

    Partial atrioventricular septal defect results from failure of the endocardial cushions to fuse, producing a low atrial defect adjacent to the atrioventricular valves together with a cleft anterior mitral leaflet. The result is left-to-right shunting and often mitral regurgitation.

  178. Question 178Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which color and spectral Doppler pattern is characteristic of a haemodynamically significant patent ductus arteriosus?

    1. A systolic-only jet entering the main pulmonary artery from the right ventricle
    2. A continuous high-velocity jet entering the main pulmonary artery near the left pulmonary artery Correct answer.
    3. A continuous low-velocity jet within the coronary sinus
    4. A diastolic jet entering the aorta just distal to the left subclavian artery

    Explanation

    Because aortic pressure exceeds pulmonary artery pressure throughout the cardiac cycle, a ductal shunt produces continuous left-to-right flow that enters the pulmonary artery at the junction with the left pulmonary artery. The continuous murmur corresponds to this holodiastolic and holosystolic flow.

  179. Question 179Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    An echo-free space is seen anterior to the right ventricle in a patient with a large body habitus. Which finding supports epicardial fat rather than a pericardial effusion?

    1. The space is larger posteriorly than anteriorly
    2. The space compresses the right ventricular free wall in diastole
    3. The space enlarges substantially during inspiration
    4. The space is confined anteriorly, moves with the heart and shows tissue-like texture Correct answer.

    Explanation

    Epicardial fat lies anteriorly, moves with the myocardium and displays fine textured echoes rather than uniform anechoic fluid. It also tends to compress slightly with cardiac motion, whereas a simple effusion is uniformly echo-free and conforms to the pericardial space.

  180. Question 180Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which set of findings suggests left ventricular noncompaction?

    1. Uniform wall thickness with normal trabeculation and a bright endocardium
    2. A bilayered myocardium with a thick noncompacted layer and deep intertrabecular recesses Correct answer.
    3. A thin compacted wall with a smooth endocardial surface and a small cavity
    4. Isolated apical hypertrophy with an intracavitary pressure gradient

    Explanation

    Noncompaction produces a two-layered wall in which a thickened, spongy noncompacted layer overlies a thin compacted epicardial layer, with blood-filled recesses communicating with the cavity. A noncompacted-to-compacted ratio above 2.0 in systole is the usual criterion.

  181. Question 181Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient with a large pericardial effusion has persistently elevated right atrial pressure after pericardiocentesis, together with a diastolic septal bounce and respiratory ventricular interdependence. What is the most likely explanation?

    1. Right ventricular infarction
    2. Severe tricuspid regurgitation
    3. Effusive-constrictive pericarditis Correct answer.
    4. Recurrent pericardial tamponade

    Explanation

    Effusive-constrictive pericarditis occurs when visceral pericardial constraint persists after fluid is removed, so right atrial pressure fails to normalise and constrictive physiology becomes apparent. The septal bounce and ventricular interdependence unmasked after drainage are diagnostic.

  182. Question 182Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which tissue Doppler finding favours constrictive pericarditis over restrictive cardiomyopathy?

    1. Lateral annular e-prime above 10 cm/s with a normal E/e-prime ratio
    2. Medial annular e-prime greater than lateral annular e-prime Correct answer.
    3. Markedly reduced medial and lateral e-prime of equal magnitude
    4. A lateral e-prime that rises further during inspiration

    Explanation

    In constriction the tethered lateral annulus moves poorly, so its velocity falls below that of the less affected medial annulus, a pattern termed annulus reversus. Restrictive cardiomyopathy typically shows reduced velocities at both sites with lateral remaining higher than medial.

  183. Question 183Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic feature best favours hypertrophic cardiomyopathy over hypertensive left ventricular hypertrophy?

    1. A septal-to-posterior wall ratio above 1.3 with a small cavity and systolic anterior motion Correct answer.
    2. Concentric hypertrophy with a septal-to-posterior wall ratio below 1.3
    3. Left atrial enlargement with a reduced medial annular e-prime
    4. Mild aortic regurgitation with a trileaflet aortic valve

    Explanation

    Hypertensive hypertrophy is usually concentric and proportionate, whereas hypertrophic cardiomyopathy is typically asymmetric with a septal-to-posterior ratio above 1.3 and a small, hyperdynamic cavity. Systolic anterior motion and a dynamic gradient further support cardiomyopathy.

  184. Question 184Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which criterion supports the echocardiographic diagnosis of Ebstein anomaly in an adult?

    1. Septal tricuspid leaflet displacement of 8 mm/m2 or more Correct answer.
    2. Tethering of the septal tricuspid leaflet with normal annular insertion
    3. Dysplasia of the mitral valve with a cleft anterior leaflet
    4. Anterior tricuspid leaflet displacement of 4 mm/m2 or more

    Explanation

    Ebstein anomaly is diagnosed when the septal tricuspid leaflet inserts apically by at least 8 mm/m2 relative to the anterior mitral leaflet. The displaced leaflets partition the right ventricle into a thin-walled atrialised portion and a smaller functional chamber.

  185. Question 185Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient with cardiac tamponade is being ventilated with positive pressure. Which Doppler pattern should be expected?

    1. Respiratory variation of mitral inflow is reduced or reversed relative to spontaneous breathing Correct answer.
    2. A mitral E velocity that is completely fixed in every patient
    3. An exaggerated inspiratory rise in mitral inflow velocity above 40 percent
    4. Loss of respiratory variation confined to tricuspid inflow alone

    Explanation

    Positive-pressure ventilation reverses the normal inspiratory augmentation of venous return, so the classic respiratory swings in mitral and tricuspid inflow may be blunted or inverted. Tamponade criteria derived from spontaneously breathing patients are therefore less reliable in ventilated patients.

  186. Question 186Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A 58-year-old man of Japanese descent with exertional chest pain has giant negative T waves on ECG. Echocardiography shows marked hypertrophy confined to the left ventricular apex with a spade-shaped cavity at end-diastole. What is the most likely diagnosis?

    1. Left ventricular noncompaction
    2. Hypertensive concentric left ventricular hypertrophy
    3. Apical hypertrophic cardiomyopathy Correct answer.
    4. Cardiac amyloidosis

    Explanation

    Apical hypertrophic cardiomyopathy produces hypertrophy confined to the apex, a spade-shaped left ventricular cavity at end-diastole, and often giant negative T waves on ECG. The pattern is distinct from diffuse or asymmetric septal hypertrophy.

  187. Question 187Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    In a patient with hypertrophic cardiomyopathy, systolic anterior motion of the anterior mitral leaflet during systole causes which hemodynamic consequence?

    1. A fixed subaortic gradient
    2. Left ventricular inflow obstruction
    3. Dynamic LVOT obstruction Correct answer.
    4. Severe aortic stenosis

    Explanation

    Systolic anterior motion of the mitral leaflet narrows the left ventricular outflow tract during systole, producing a dynamic gradient that varies with loading conditions. This is a hallmark mechanism of obstruction in hypertrophic cardiomyopathy.

  188. Question 188Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic pattern is most typical of cardiac amyloidosis?

    1. Severe left ventricular trabeculation
    2. Granular sparkling myocardium with biatrial enlargement Correct answer.
    3. Dilated, thin-walled left ventricle with severely reduced ejection fraction
    4. Isolated apical hypertrophy with apical sparing

    Explanation

    Amyloid infiltration thickens the myocardium and produces a granular or sparkling texture, along with biatrial enlargement, valve thickening, and often a small pericardial effusion. Systolic function may be preserved until late in the disease.

  189. Question 189Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    On a parasternal long-axis view, an echo-free space is seen posterior to the left atrium but anterior to the descending thoracic aorta. This space most likely represents which structure?

    1. Pleural effusion with loculation
    2. Pericardial effusion Correct answer.
    3. Dilated esophageal varices
    4. Coronary sinus

    Explanation

    Pericardial fluid tracks anterior to the descending thoracic aorta, whereas pleural fluid lies posterior to the descending aorta. This relationship helps distinguish a pericardial from a pleural effusion.

  190. Question 190Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic finding is most consistent with a bicuspid aortic valve?

    1. A trileaflet valve with central coaptation and a central regurgitant jet
    2. Thickened leaflets with commissural fusion and a hockey-stick appearance
    3. Eccentric systolic closure with a raphe and systolic doming Correct answer.
    4. A quadrileaflet valve with a rectangular systolic orifice

    Explanation

    A bicuspid aortic valve typically shows two functional cusps, an eccentric systolic closure line, a raphe, and systolic doming of the leaflets. It is frequently associated with aortic dilatation and coarctation.

  191. Question 191Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A young adult with upper extremity hypertension and weak femoral pulses undergoes echocardiography. Which Doppler finding from the suprasternal notch is most consistent with coarctation of the aorta?

    1. Loss of the systolic notch in the aortic arch
    2. A bicuspid aortic valve with normal arch flow
    3. Systolic flow reversal throughout the descending aorta
    4. Continuous antegrade flow with a diastolic tail Correct answer.

    Explanation

    Coarctation produces a narrowed aortic isthmus with a persistent pressure gradient, resulting in continuous antegrade flow into diastole, often called a diastolic tail. The finding is best demonstrated from the suprasternal notch.

  192. Question 192Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A 40-year-old woman with a large atrial septal defect is found to have anomalous pulmonary venous drainage. Which ASD subtype is most likely?

    1. Coronary sinus defect
    2. Sinus venosus defect Correct answer.
    3. Ostium primum defect
    4. Ostium secundum defect

    Explanation

    Sinus venosus defects occur near the superior or inferior vena cava and are frequently associated with partial anomalous pulmonary venous return. Ostium primum defects are instead associated with cleft anterior mitral leaflet and an atrioventricular septal defect.

  193. Question 193Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic feature is most characteristic of rheumatic mitral stenosis?

    1. Papillary muscle rupture with flail leaflet
    2. Leaflet prolapse with chordal rupture
    3. Commissural fusion with diastolic doming Correct answer.
    4. Annular calcification with preserved commissures

    Explanation

    Rheumatic mitral stenosis causes commissural fusion, leaflet thickening, and diastolic doming of the anterior leaflet, often described as a hockey-stick appearance. These changes restrict leaflet opening and reduce mitral valve area.

  194. Question 194Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient 10 days after an inferior myocardial infarction has a pulsatile left ventricular mass with a narrow neck (neck-to-body ratio less than 0.5). What is the most likely diagnosis?

    1. Apical hypertrophic cardiomyopathy
    2. Left ventricular diverticulum
    3. Left ventricular pseudoaneurysm Correct answer.
    4. True left ventricular aneurysm

    Explanation

    A pseudoaneurysm results from contained myocardial rupture and is characterised by a narrow neck, with a neck-to-body ratio typically less than 0.5. It carries a high risk of rupture and requires urgent evaluation.

  195. Question 195Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient with carcinoid heart disease is likely to show which echocardiographic pattern?

    1. Aortic regurgitation with an eccentric jet
    2. Pulmonary valve vegetation
    3. Retracted tricuspid leaflets with severe regurgitation Correct answer.
    4. Mitral stenosis with commissural fusion

    Explanation

    Carcinoid heart disease produces fibrous thickening and retraction of the tricuspid and pulmonary valve leaflets, leading to severe tricuspid regurgitation and pulmonary regurgitation. Left-sided valves are usually spared unless there is a right-to-left shunt.

  196. Question 196Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic finding best supports a diagnosis of acute aortic dissection involving the ascending aorta?

    1. An intimal flap in the ascending aorta Correct answer.
    2. Central aortic regurgitation with a normal root
    3. Diffuse intimal thickening
    4. Aortic valve doming

    Explanation

    An intimal flap separating a true and false lumen in the ascending aorta is the direct echocardiographic sign of aortic dissection. It may be accompanied by aortic regurgitation, pericardial effusion, or root dilatation.

  197. Question 197Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A patient is found to have a dilated coronary sinus on echocardiography. Which congenital anomaly should be suspected?

    1. Persistent left superior vena cava Correct answer.
    2. A large secundum atrial septal defect
    3. Aortic coarctation
    4. Anomalous left coronary artery

    Explanation

    A persistent left superior vena cava drains into the coronary sinus, increasing its flow and causing dilatation. This can be confirmed by agitated saline injection from the left arm.

  198. Question 198Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A young patient has a ventricular septal defect whose color Doppler jet enters the right ventricle just below the pulmonary valve. Which complication is most likely?

    1. Aortic cusp prolapse with aortic regurgitation Correct answer.
    2. Tricuspid atresia
    3. Severe mitral regurgitation from chordal rupture
    4. Pulmonary vein stenosis

    Explanation

    A supracristal or outlet ventricular septal defect lies immediately beneath the pulmonary valve and adjacent to the aortic cusps. The Venturi effect can cause aortic cusp prolapse and progressive aortic regurgitation.

  199. Question 199Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    Which echocardiographic finding is most suggestive of cardiac sarcoidosis in a patient with new complete heart block?

    1. Apical ballooning
    2. Basal septal thinning with reduced strain Correct answer.
    3. Symmetric septal hypertrophy
    4. Severe left atrial dilatation with mitral stenosis

    Explanation

    Cardiac sarcoidosis causes patchy myocardial infiltration and fibrosis, often affecting the basal septum and producing regional thinning and reduced strain despite a preserved ejection fraction. Conduction block is a common clinical manifestation.

  200. Question 200Cardiomyopathy, pericardial disease, and congenital/acquired pathology

    A 45-year-old man with acroparesthesias and renal failure has severe concentric left ventricular hypertrophy on echocardiography. Which additional finding would most favor Fabry disease over hypertensive heart disease?

    1. Pericardial effusion with thickened valves and biatrial enlargement
    2. Biventricular hypertrophy with a binary myocardial texture Correct answer.
    3. Apical hypertrophy with a spade-shaped cavity
    4. Systolic anterior motion of the mitral valve

    Explanation

    Fabry disease commonly causes concentric left ventricular hypertrophy with prominent papillary muscles, right ventricular hypertrophy, and a binary myocardial texture. These features help distinguish it from hypertensive remodeling.

Adult Echocardiography (AE) flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Left ventricular ejection fraction
Ejection fraction equals end-diastolic volume minus end-systolic volume divided by end-diastolic volume; normal is approximately 55-70% by Simpson's biplane method.
Cardiac output formula
Cardiac output equals stroke volume multiplied by heart rate; stroke volume can be derived from LVOT area times LVOT velocity-time integral.
Right ventricular systolic pressure
RVSP equals 4 times the square of peak tricuspid regurgitation velocity plus right atrial pressure estimated from IVC size and collapse.
Normal mitral valve area
The normal mitral valve orifice is 4-6 cm²; an area below 1.5 cm² indicates moderate to severe mitral stenosis.
Diastolic function grades
Grade 1 shows E/A below 0.8; grade 2 shows E/A 0.8-1.5 with elevated filling pressures; grade 3 shows E/A above 2 with restrictive filling.
Seventeen segment model
The left ventricle is divided into six basal, six mid, four apical segments, and an apical cap; the apex is assigned to the LAD territory.
Nyquist limit
The Nyquist limit is half the pulse repetition frequency; Doppler shifts above it alias and wrap to the opposite direction on spectral display.
Aliasing
Aliasing occurs when the Doppler shift exceeds the Nyquist limit, producing wrap-around or ambiguous color and spectral display; increase PRF or lower frequency.
Axial resolution
Axial resolution equals spatial pulse length divided by two; higher frequency and fewer cycles per pulse improve it to approximately 0.5-1 mm.
Doppler equation
Doppler shift equals 2 times transducer frequency times blood velocity times cosine of the angle, divided by tissue propagation velocity.
Attenuation in soft tissue
Attenuation is about 0.5 dB per centimeter per megahertz one-way; higher frequencies improve resolution but reduce penetration.
Mechanical index
Mechanical index equals peak negative pressure in megapascals divided by the square root of frequency in megahertz; it estimates cavitation risk.
Frame rate determinants
Frame rate equals pulse repetition frequency divided by lines per frame; color Doppler and wider sectors reduce frame rate.
Parasternal long-axis view
This view shows the right ventricle anteriorly, left ventricle, aortic root, and left atrium; LVOT diameter is measured in mid-systole.
Simpson's biplane method
End-diastolic and end-systolic endocardial borders are traced in apical four- and two-chamber views to calculate LV volumes and ejection fraction.
Pulsed-wave Doppler
PW Doppler uses a sample volume to detect low velocities with range resolution but aliases above the Nyquist limit; it is used for LVOT and mitral inflow.
Continuous-wave Doppler
CW Doppler records all velocities along the beam without aliasing but without range resolution; it is used for high-velocity jets such as aortic stenosis.
Tissue Doppler imaging
Tissue Doppler measures low-velocity myocardial motion at the mitral annulus; septal e' below 7 cm/s suggests impaired relaxation.
Doppler angle correction
Flow velocity is accurate when the ultrasound beam is within 60 degrees of flow; angle correction applies to vascular flow, not cardiac valve jets.
Continuity equation
Aortic valve area equals LVOT area times LVOT velocity-time integral divided by aortic valve velocity-time integral; it is used for aortic stenosis severity.
Severe aortic stenosis
Severe aortic stenosis is defined by peak velocity at least 4 m/s, mean gradient at least 40 mmHg, or valve area below 1.0 cm².
Pressure half-time
Mitral valve area equals 220 divided by pressure half-time in milliseconds; a half-time above 220 ms suggests severe mitral stenosis.
Vena contracta
The narrowest jet width just downstream of a regurgitant orifice; a vena contracta of at least 0.7 cm indicates severe mitral regurgitation.
PISA method
Proximal isovelocity surface area calculates effective regurgitant orifice area using flow convergence radius, aliasing velocity, and peak regurgitant velocity.
Aortic regurgitation half-time
A pressure half-time below 200 ms suggests severe aortic regurgitation; holodiastolic flow reversal in the descending aorta supports severity.
Prosthetic valve gradients
Normal mean gradients are generally below 20 mmHg for aortic and below 5 mmHg for mitral prostheses; higher values suggest obstruction or mismatch.
Hypertrophic cardiomyopathy
Asymmetric septal hypertrophy of at least 15 mm with systolic anterior motion of the mitral leaflet can cause dynamic LVOT obstruction and gradient at least 30 mmHg.
Cardiac amyloidosis
Amyloid shows thickened ventricles, granular sparkling texture, apical sparing of longitudinal strain, and low ECG voltage relative to wall thickness.
Cardiac tamponade
Tamponade shows a pericardial effusion with right atrial systolic collapse, right ventricular diastolic collapse, IVC plethora, and respiratory flow variation.
Constrictive pericarditis
Constrictive pericarditis shows pericardial thickening, septal bounce, annulus paradoxus, and medial e' greater than lateral e' on tissue Doppler.
Dilated cardiomyopathy
Dilated cardiomyopathy shows LV dilation and reduced ejection fraction, often with functional mitral regurgitation; LV thrombus may require anticoagulation.
Aortic dissection flap
An intimal flap in the ascending aorta indicates Stanford type A dissection, a surgical emergency; color Doppler may show true and false lumens.

Adult Echocardiography (AE) study guide

Cardiac Anatomy and Physiology: Chambers, Segments, and the Cardiac Cycle

Chamber anatomy and the segment model

Begin with the fibrous skeleton: the aortic valve sits centrally, the anterior mitral leaflet is continuous with the aortic root, and this relationship explains why root disease can produce mitral pathology. The LV is a truncated ellipsoid whose subendocardial fibers run longitudinally - they are the first to fail in ischemia, which is why longitudinal strain drops before ejection fraction does.

Candidates must map the 17-segment model (6 basal, 6 mid, 4 apical, plus the apical cap) to coronary territories. LAD supplies anterior, anteroseptal, and apical segments; LCx supplies anterolateral and inferolateral walls; RCA supplies inferior and inferoseptal segments in a right-dominant system.

Physiology questions favor the phases of the cardiac cycle - isovolumic contraction, rapid and reduced ejection, isovolumic relaxation, rapid filling, diastasis, atrial systole - and the pressure–volume loop, where the end-systolic pressure–volume relation indexes contractility, the end-diastolic relation indexes compliance, and loop area equals stroke work.

Normal values worth memorizing: LV ejection fraction 55–70%, LV end-diastolic dimension 3.5–5.6 cm, wall thickness up to 1.0 cm, LA volume index 22–34 mL/m², TAPSE ≥1.7 cm.

Traps: the moderator band and three tricuspid papillary groups identify the RV; the coronary sinus drains into the right atrium; apical segments are frequently lost to foreshortening.

Rule of thumb: when one segment is abnormal, name the supplying artery and inspect its paired segment - a wall motion abnormality that does not fit a coronary territory suggests artifact or a non-ischemic process.

Ultrasound Physics and Instrumentation: Resolution, Doppler, and Artifacts

Resolution, attenuation, and artifacts

Sound travels at approximately 1540 m/s in soft tissue. Higher frequency means shorter wavelength, better axial resolution, and worse penetration - the central trade-off behind most physics items. Axial resolution equals spatial pulse length divided by two; a 3-MHz transducer with a 3-cycle pulse yields about 0.77 mm. Lateral and elevational resolution depend on beam width, not pulse length, and improve with focusing and harmonic imaging.

The Doppler equation relates frequency shift to velocity and the cosine of the angle; alignment within 20° keeps error under about 6%. Aliasing occurs when the Doppler shift exceeds the Nyquist limit (PRF/2). Three fixes: raise the scale/PRF, shift the baseline, or switch to continuous wave. Frame rate equals PRF divided by lines per frame, so increasing depth or sector width degrades temporal resolution - critical when timing rapid events.

Recognize the artifacts: reverberation and comet tail from strong reflectors, shadowing behind calcium, enhancement behind fluid, mirror image behind a strong interface, side-lobe and range-ambiguity clutter, twinkling behind crystals.

Bioeffects: mechanical index rises with peak negative pressure and falls with frequency; Doppler delivers more energy than 2D, so apply ALARA.

Rule of thumb: if the image looks better but the measurement got worse, check your settings - harmonic imaging, higher frequency, and added gain improve the picture but can shift numbers.

Two-Dimensional, M-mode, and Doppler Acquisition Technique

Windows, modes, and measurement conventions

Acquisition items test whether you know which window answers which question. Parasternal long axis: LV dimensions, aortic root, valve morphology, pericardial effusion, and the LVOT diameter. Parasternal short axis at aortic, mitral, and papillary levels: leaflet motion, segmental wall motion, LV geometry. Apical four, two, three, and five chamber: all four valves by Doppler, LV volumes, LVOT flow. Subcostal: effusion, IVC, interatrial septum. Suprasternal: arch and descending aorta.

M-mode offers excellent axial and temporal resolution but samples a single line, so it cannot assess lateral structures - never grade a structure that drifts off the cursor.

Doppler rules: angle correct only when the cursor cannot be aligned with flow; use PW for localized low-velocity flow and CW for high velocities (gradients above roughly 2 m/s alias on PW); place the LVOT sample volume 0.5–1 cm proximal to the aortic valve in the apical five-chamber view; measure the LVOT diameter inner-edge to inner-edge in mid-systole in a zoomed long axis. Tissue Doppler uses low-velocity, high-amplitude filter settings to record septal and lateral e′.

Traps: measuring LVOT diameter from the apical view, using the apical three-chamber for aortic gradients, planimetering a heavily calcified aortic valve, and forgetting that color Doppler scale changes alter apparent jet area.

Rule of thumb: a diameter comes from 2D, a velocity comes from Doppler, and any velocity above 2 m/s needs continuous wave.

Valvular Heart Disease and Hemodynamics

Quantifying stenosis and regurgitation

Valve questions reward a systematic approach. Aortic stenosis: integrate peak velocity, mean gradient, continuity-derived area (AVA = 0.785 × D² × VTI_LVOT ÷ VTI_AV), and dimensionless index (VTI ratio <0.25 indicates severe). Severe AS: peak velocity ≥4 m/s, mean gradient ≥40 mmHg, AVA ≤1.0 cm². Beware low-flow, low-gradient AS with reduced EF - use low-dose dobutamine to demonstrate contractile reserve and true severity - and paradoxical low-flow AS with preserved EF and a small, thick LV.

Mitral stenosis: planimetered area ≤1.5 cm² is severe; the pressure half-time method (220 ÷ PHT) is unreliable immediately after balloon valvuloplasty and in significant aortic regurgitation.

Regurgitation is graded with color jet size, vena contracta, PISA-derived EROA, regurgitant volume/fraction, and adjunct signs. Mitral: EROA ≥0.4 cm², vena contracta ≥0.7 cm, systolic pulmonary vein flow reversal. Aortic: vena contracta ≥0.6 cm, holodiastolic flow reversal in the descending aorta, pressure half-time <200 ms. Tricuspid: dense jet with hepatic vein systolic reversal.

Core hemodynamics: simplified Bernoulli ΔP = 4V²; RVSP = 4 × TR velocity² + right atrial pressure.

Traps: mean gradient is flow-dependent, peak gradient is not interchangeable with mean gradient, and a misaligned CW cursor underestimates severity.

Rule of thumb: never grade severity from one number - for any regurgitant lesion, find three concordant signs.

Cardiomyopathy, Pericardial Disease, and Congenital/Acquired Pathology

Recognizing the classic patterns

Hypertrophic cardiomyopathy: asymmetric septal hypertrophy ≥15 mm (≥13 mm in relatives), systolic anterior motion of the mitral leaflet, dynamic LVOT obstruction (gradient ≥30 mmHg at rest or with provocation), mid-systolic aortic valve notching, and apical hypertrophy with a spade-shaped cavity.

Dilated cardiomyopathy: LV dilatation with EF <45%, global hypokinesis, and functional regurgitation. Restrictive physiology (amyloid, sarcoid, radiation) shows biatrial enlargement with normal or small ventricles, E/A >2, high E/e′, and low e′ velocities; amyloid also produces a granular appearance and relative apical sparing of longitudinal strain. Takotsubo shows apical ballooning with basal hyperkinesis.

Pericardial disease: tamponade is a clinical diagnosis supported by early diastolic right atrial and diastolic right ventricular collapse, a plethoric IVC, and >25% respiratory variation in mitral inflow. Constriction shows a septal bounce, annulus reversus (medial e′ > lateral e′), expiratory diastolic flow reversal in hepatic veins, and respiratory variation in mitral inflow.

Congenital and acquired lesions: secundum ASD with right heart enlargement (sinus venosus defects need TEE); bicuspid aortic valve with root dilatation; coarctation with a suprasternal gradient and diastolic run-off; Ebstein anomaly with apical displacement of the septal tricuspid leaflet.

Traps: "sparkling" myocardium is nonspecific, pleural and pericardial fluid are separated by the descending aorta, and tamponade physiology can occur with a modest effusion.

Rule of thumb: E/e′ >14, medial e′ <7 cm/s, and TR velocity >2.8 m/s together signal elevated filling pressure.

Adult Echocardiography (AE) cheat sheet

Quick reference

Cardiac Anatomy and Physiology

  • The left ventricle is divided into 17 segments: six basal, six mid, four apical, and one apical cap; the apical segments and cap are assigned to the LAD territory.

  • Ejection fraction equals end-diastolic volume minus end-systolic volume divided by end-diastolic volume; a normal value is approximately 55-70%.

  • Cardiac output equals stroke volume times heart rate; stroke volume can be calculated as LVOT area multiplied by LVOT velocity-time integral.

  • LVOT area is calculated as pi times the square of half the LVOT diameter; the diameter is measured in mid-systole in the parasternal long-axis view.

  • Grade 1 diastolic dysfunction shows E/A below 0.8; grade 2 shows E/A 0.8-1.5 with elevated filling pressures; grade 3 shows E/A above 2 with restrictive filling.

  • Septal e' below 7 cm/s and lateral e' below 10 cm/s suggest impaired myocardial relaxation; E/e' above 14 suggests elevated left atrial pressure.

  • Right ventricular systolic pressure equals 4 times the square of peak tricuspid regurgitation velocity plus right atrial pressure estimated from IVC size and collapse.

  • Normal valve areas are approximately 3-4 cm² for the aortic valve, 4-6 cm² for the mitral valve, 7 cm² for the tricuspid valve, and 3 cm² for the pulmonary valve.

  • The normal pericardial space contains less than 50 mL of fluid; an echo-free space between the pericardium and myocardium indicates a pericardial effusion.

Quick reference

Ultrasound Physics and Instrumentation

  • Frequency equals propagation velocity divided by wavelength; average soft-tissue propagation velocity is approximately 1540 m/s.

  • Attenuation in soft tissue is approximately 0.5 dB per centimeter per megahertz one-way; higher frequencies improve resolution but reduce penetration.

  • Axial resolution equals spatial pulse length divided by two; it improves with higher frequency and fewer cycles per pulse and is typically 0.5-1 mm.

  • Lateral resolution is worse than axial resolution and depends on beam width, transducer frequency, and depth; it improves with focusing.

  • The Nyquist limit equals pulse repetition frequency divided by two; Doppler shifts above this limit alias and wrap to the opposite direction.

  • Aliasing can be reduced by increasing pulse repetition frequency, lowering transducer frequency, or adjusting the color scale and baseline.

  • The Doppler equation is shift equals 2 times transducer frequency times velocity times cosine of the angle, divided by propagation velocity.

  • Pulsed-wave Doppler provides range resolution but aliases; continuous-wave Doppler records high velocities without aliasing but lacks range resolution.

  • Frame rate equals pulse repetition frequency divided by lines per frame; color Doppler, wider sectors, and greater depth reduce frame rate.

Quick reference

Two-Dimensional, M-Mode, and Doppler Acquisition Technique

  • The parasternal long-axis view displays the right ventricle anteriorly, the left ventricle, aortic root, and left atrium; LVOT diameter is measured in mid-systole.

  • The apical four-chamber view places the LV apex at the top of the sector and is used for Simpson's biplane ejection fraction and mitral inflow Doppler.

  • Simpson's biplane method traces end-diastolic and end-systolic endocardial borders in apical four- and two-chamber views to calculate LV volumes.

  • M-mode uses a single cursor line with high temporal resolution; the cursor should be perpendicular to the structure, such as the aortic valve or mitral leaflets.

  • Pulsed-wave Doppler uses a sample volume for low-velocity flow with range resolution; it is used for LVOT, mitral inflow, and pulmonary vein velocities.

  • Continuous-wave Doppler is used for high-velocity jets such as aortic stenosis because it does not alias, but it cannot localize flow along the beam.

  • Color Doppler scale should be set above the expected velocity to avoid aliasing; variance maps display turbulent flow.

  • Tissue Doppler imaging samples myocardial motion at the septal and lateral mitral annulus to measure e' and a' velocities.

  • Doppler angle correction is applied to vascular flow but not to cardiac valve jets; valve velocities are most accurate when the beam is within 20 degrees of flow.

Quick reference

Valvular Heart Disease and Hemodynamics

  • The continuity equation calculates aortic valve area as LVOT area times LVOT VTI divided by aortic valve VTI.

  • Severe aortic stenosis is defined by peak velocity at least 4 m/s, mean gradient at least 40 mmHg, or valve area below 1.0 cm².

  • The dimensionless index is LVOT VTI divided by aortic valve VTI; a value below 0.25 indicates severe aortic stenosis.

  • Mitral valve area by pressure half-time equals 220 divided by pressure half-time in milliseconds; a half-time above 220 ms suggests severe mitral stenosis.

  • Severe mitral regurgitation is suggested by a vena contracta of at least 0.7 cm or a PISA-derived effective regurgitant orifice area of at least 0.4 cm².

  • Aortic regurgitation pressure half-time below 200 ms suggests severe regurgitation; holodiastolic flow reversal in the descending aorta supports severity.

  • Tricuspid regurgitation velocity above 2.8 m/s suggests elevated right ventricular systolic pressure; a value above 3.4 m/s suggests severe pulmonary hypertension.

  • Normal prosthetic mean gradients are generally below 20 mmHg for aortic and below 5 mmHg for mitral valves; higher gradients suggest obstruction or patient-prosthesis mismatch.

  • Pulmonary stenosis with a peak velocity above 4 m/s or a mean gradient above 40 mmHg is considered severe.

Quick reference

Cardiomyopathy, Pericardial Disease, and Congenital/Acquired Pathology

  • Hypertrophic cardiomyopathy shows asymmetric septal hypertrophy of at least 15 mm, systolic anterior motion of the mitral leaflet, and dynamic LVOT obstruction with gradient at least 30 mmHg.

  • Cardiac amyloidosis shows thickened ventricular walls, a granular sparkling texture, apical sparing of longitudinal strain, and low ECG voltage relative to wall thickness.

  • Restrictive cardiomyopathy shows biatrial enlargement, normal or reduced LV cavity size, and grade 3 diastolic dysfunction with elevated filling pressures.

  • Cardiac tamponade shows a pericardial effusion with right atrial systolic collapse, right ventricular diastolic collapse, IVC plethora, and respiratory variation in inflow velocities.

  • Constrictive pericarditis shows pericardial thickening, septal bounce, annulus paradoxus, and medial e' greater than lateral e' on tissue Doppler.

  • Dilated cardiomyopathy shows LV dilation and reduced ejection fraction, often with functional mitral regurgitation; LV thrombus may require anticoagulation.

  • An atrial septal defect causes right heart volume overload, color flow across the interatrial septum, and increased pulmonary-to-systemic flow ratio.

  • A Stanford type A aortic dissection shows an intimal flap in the ascending aorta and is a surgical emergency; color Doppler may distinguish true and false lumens.

Adult Echocardiography (AE) key terms

Ejection fraction

The percentage of blood in the left ventricle that is pumped out with each heartbeat, calculated as stroke volume divided by end-diastolic volume. A key measure of systolic function.

Related: Stroke volume, Cardiac output
Stroke volume

The volume of blood ejected by a ventricle in a single beat, typically calculated as the difference between end-diastolic and end-systolic volumes. It reflects both loading conditions and contractility.

Related: Ejection fraction, Preload
Cardiac output

The total volume of blood pumped by the heart per minute, equal to stroke volume multiplied by heart rate. It is a core indicator of overall circulatory performance.

Related: Stroke volume, Ejection fraction
Preload

The degree of ventricular stretch at the end of diastole, often estimated by end-diastolic volume or filling pressures. Increased preload generally increases stroke volume within physiologic limits.

Related: Afterload, Stroke volume
Afterload

The resistance or load the ventricle must overcome to eject blood during systole, influenced by vascular resistance, arterial pressure, and wall stress. Higher afterload tends to reduce stroke volume and ejection fraction.

Related: Preload, Ejection fraction
Diastole

The phase of the cardiac cycle when the ventricles relax and fill with blood, encompassing isovolumic relaxation, rapid filling, diastasis, and atrial contraction. Diastolic function is assessed with Doppler and tissue Doppler.

Related: E/e' ratio, Left atrial volume index
TAPSE

Tricuspid annular plane systolic excursion, the distance the tricuspid annulus moves toward the apex during systole, measured by M-mode. It estimates right ventricular longitudinal systolic function.

Related: M-mode, Right ventricular systolic pressure
Left atrial volume index

Left atrial volume divided by body surface area, used as a marker of chronic left ventricular filling pressure and diastolic dysfunction. Normal values are roughly below 34 mL/m².

Related: E/e' ratio, Diastole
Piezoelectric effect

The property of certain crystals to change shape when an electric current is applied, generating ultrasound waves, and to generate an electric charge when deformed by returning sound waves.

Related: Acoustic impedance, Attenuation
Nyquist limit

The maximum Doppler frequency shift that can be displayed unambiguously by pulsed-wave Doppler, equal to half the pulse repetition frequency. Shifts above it cause aliasing.

Related: Aliasing, Pulsed-wave Doppler
Aliasing

Ambiguous display of Doppler velocities that exceed the Nyquist limit, appearing as wraparound of the spectral waveform or color scale to the opposite side. Continuous-wave Doppler is not subject to aliasing.

Related: Nyquist limit, Continuous-wave Doppler
Acoustic impedance

The resistance of a medium to sound propagation, determined by tissue density and sound speed. Differences in impedance at tissue interfaces produce reflections that create ultrasound images.

Related: Attenuation, Piezoelectric effect
Attenuation

The progressive loss of ultrasound energy as it travels through tissue due to absorption, reflection, and scattering. It increases with depth and higher transducer frequencies.

Related: Acoustic impedance, Axial resolution
Axial resolution

The ability to distinguish two structures lying along the path of the ultrasound beam, determined primarily by transducer frequency and pulse duration. Higher frequencies improve axial resolution.

Related: Attenuation, Frame rate
Frame rate

The number of complete two-dimensional images generated per second. It depends on depth and sector width and affects temporal resolution, which matters for fast-moving structures.

Related: Axial resolution, Color Doppler
Continuous-wave Doppler

A Doppler mode that continuously transmits and receives ultrasound along a line, detecting the highest velocities anywhere along the beam without aliasing. Used for high-velocity flow such as aortic stenosis.

Related: Pulsed-wave Doppler, Aliasing
Pulsed-wave Doppler

A Doppler mode that transmits short pulses and listens at a specific depth (sample volume), providing depth-specific velocity information but limited by the Nyquist limit and aliasing.

Related: Nyquist limit, Continuous-wave Doppler
Color Doppler

Superimposes color on the two-dimensional image to display direction and velocity of blood flow, with color assigned by flow toward or away from the transducer. Useful for detecting regurgitation and shunts.

Related: Vena contracta, Tissue Doppler imaging
Tissue Doppler imaging

A Doppler technique that records low-velocity, high-amplitude myocardial motion rather than blood flow, used to measure annular velocities such as e' and s' for diastolic and systolic function.

Related: E/e' ratio, Speckle tracking
Speckle tracking

An echocardiographic method that follows the movement of unique acoustic speckle patterns within myocardium across frames to calculate strain and deformation independent of Doppler angle.

Related: Tissue Doppler imaging, Ejection fraction
M-mode

A one-dimensional recording of motion along a single line of the ultrasound beam over time, offering high temporal resolution for measuring chamber dimensions and valve motion.

Related: TAPSE, Apical four-chamber view
Apical four-chamber view

A standard view obtained with the transducer at the cardiac apex, displaying both ventricles and atria with the septum vertical. It is used for chamber sizing, function, and Doppler interrogation.

Related: M-mode, Color Doppler
Vena contracta

The narrowest cross-sectional width of a regurgitant jet immediately downstream of the regurgitant orifice, measured by color Doppler. Width correlates with regurgitation severity.

Related: Proximal isovelocity surface area, Color Doppler
Proximal isovelocity surface area

A method that measures the radius of the hemispheric flow convergence region proximal to a regurgitant orifice to calculate effective regurgitant orifice area and regurgitant volume.

Related: Vena contracta, Pressure half-time
Pressure half-time

The time required for the peak pressure gradient across a valve to fall by half. It is used to estimate mitral valve area in stenosis and to assess regurgitation severity.

Related: Continuity equation, Mean gradient
Continuity equation

A calculation based on conservation of flow that uses the stroke volume in the left ventricular outflow tract to derive aortic valve area by dividing by the aortic jet velocity-time integral.

Related: Mean gradient, Pressure half-time
Mean gradient

The average pressure difference across a valve during flow, derived from the Doppler velocity spectrum using the Bernoulli equation. It reflects stenosis severity and relates to flow.

Related: Continuity equation, Pressure half-time
E/e' ratio

The ratio of early mitral inflow velocity (E) to early diastolic tissue Doppler annular velocity (e'), used to estimate left ventricular filling pressures noninvasively.

Related: Tissue Doppler imaging, Diastole
Right ventricular systolic pressure

An estimate of pulmonary artery systolic pressure derived from the tricuspid regurgitant jet velocity plus estimated right atrial pressure, used to evaluate pulmonary hypertension.

Related: TAPSE, Atrial septal defect
Hypertrophic cardiomyopathy

A genetic myocardial disease characterized by unexplained left ventricular hypertrophy, often asymmetric septal, with diastolic dysfunction and possible dynamic outflow tract obstruction.

Related: Diastole, E/e' ratio
Cardiac tamponade

A life-threatening condition in which pericardial fluid raises intrapericardial pressure, impairing ventricular filling. Echocardiography shows chamber collapse and respiratory variation in flow velocities.

Related: Pericardial effusion, Constrictive pericarditis
Constrictive pericarditis

Pericardial scarring and stiffness that restrict ventricular filling, producing diastolic dysfunction with preserved systolic function. Findings include pericardial thickening and respiratory septal bounce.

Related: Cardiac tamponade, Pericardial effusion
Mitral valve prolapse

Displacement of one or both mitral leaflets more than 2 mm beyond the annular plane into the left atrium during systole, often associated with myxomatous degeneration and mitral regurgitation.

Related: Vena contracta, Color Doppler
Bicuspid aortic valve

A congenital anomaly in which the aortic valve has two cusps instead of three, predisposing to aortic stenosis, regurgitation, and aortopathy. It is often identified by a football-shaped systolic opening.

Related: Continuity equation, Mean gradient
Atrial septal defect

A congenital opening in the atrial septum allowing left-to-right shunting, which can cause right heart enlargement. Echocardiography with color Doppler and contrast identifies the defect.

Related: Color Doppler, Right ventricular systolic pressure
Takotsubo cardiomyopathy

A transient stress-related cardiomyopathy with apical ballooning and basal hyperkinesis in the absence of obstructive coronary disease, typically resolving over days to weeks.

Related: Ejection fraction, Apical four-chamber view
Pericardial effusion

An abnormal accumulation of fluid in the pericardial space, detected as an echo-free space around the heart. Large or rapidly accumulating effusions can cause tamponade.

Related: Cardiac tamponade, Constrictive pericarditis

Adult Echocardiography (AE) study plan

8 weeks · About 6 hours per week

Week 1

Cardiac anatomy and physiology & Ultrasound physics and instrumentation

  • Label all cardiac chambers, valves, and great vessels in a parasternal, apical, and subcostal orientation without reference.

  • Trace the coronary artery distribution and the conduction system, naming the structures supplied by each vessel.

  • Describe the cardiac cycle phase by phase, matching each phase to its valve position, pressure crossover, and corresponding echo/Doppler event.

  • Explain the piezoelectric effect and derive the inverse relationship between frequency, wavelength, and axial resolution.

  • Compare axial, lateral, and elevational resolution and state which machine control affects each.

Your checkpoint

Hand-drawn, unlabeled-then-self-labeled cardiac anatomy diagram plus a 20-item anatomy/physics self-quiz scored at 80% or better, with missed items rewritten as corrected statements.

Week 2

Ultrasound physics and instrumentation

  • Calculate Nyquist limits and predict aliasing for given PRF, depth, and velocity values.

  • Differentiate the physical cause of shadowing, reverberation, comet-tail, side-lobe, mirror-image, and range-ambiguity artifacts.

  • Adjust gain, TGC, compression, frequency, and focal zone to correct a described suboptimal image, justifying each change.

  • Explain how frame rate depends on sector width, depth, and line density, and predict the effect of each on temporal resolution.

  • Distinguish continuous-wave from pulsed-wave Doppler in terms of range resolution, maximum velocity measurable, and clinical use.

Your checkpoint

A one-page artifact troubleshooting table listing 10 artifacts with appearance, cause, and corrective control, plus 15 solved physics calculations with work shown.

Week 3

Two-dimensional, M-mode, and Doppler acquisition technique

  • Sequence a complete transthoracic exam, naming the window, transducer position, and structure targeted in each of the standard views.

  • Demonstrate proper patient positioning, ECG gating, and respirometry coaching for a full study.

  • Select the correct M-mode cursor placement to measure LV dimensions, aortic root, and septal motion at end-diastole and end-systole.

  • Apply ASE measurement conventions for chamber dimensions, wall thickness, and left atrial volume.

  • Identify the views needed to answer a specific clinical question, such as source of embolus versus aortic stenosis severity.

Your checkpoint

A written 14-step scan protocol mapping each view to window, structure, and required measurement, timed against a 45-minute mock study and self-audited for omissions.

Week 4

Two-dimensional, M-mode, and Doppler acquisition technique & Valvular heart disease and hemodynamics

  • Position the color box, sample volume, and Doppler cursor correctly for aortic, mitral, tricuspid, and pulmonic interrogation.

  • Acquire and align continuous-wave Doppler through the aortic valve from apical, right parasternal, and suprasternal windows, recognizing when alignment is inadequate.

  • Apply the continuity equation to calculate aortic valve area and explain each source of measurement error.

  • Calculate mean and peak gradients from a traced spectral envelope and relate them to severity thresholds.

  • Use dimensionless index and velocity ratio to grade aortic stenosis when flow is low.

Your checkpoint

A worked aortic stenosis case workbook: 10 cases with velocity, gradient, continuity-equation area, and severity grade, each with a two-sentence justification of confidence in the measurement.

Week 5

Valvular heart disease and hemodynamics

  • Quantify mitral and aortic regurgitation using vena contracta, PISA effective regurgitant orifice, and regurgitant volume, and state the pitfalls of each.

  • Estimate right ventricular systolic pressure from tricuspid regurgitant velocity and add right atrial pressure using IVC size and collapsibility.

  • Apply pressure half-time and the continuity equation to mitral valve area and compare the two when results disagree.

  • Diagnose and grade pulmonary hypertension, including the caveats of contrast-enhanced Doppler envelopes.

  • Interpret a full hemodynamic dataset to distinguish severe from non-severe valvular disease when individual numbers conflict.

Your checkpoint

A completed 15-problem hemodynamic calculation set, including two discordant-data cases, scored at 85% or better with error analysis on every miss.

Week 6

Valvular heart disease and hemodynamics & Cardiomyopathy, pericardial disease, and congenital/acquired pathology

  • Evaluate prosthetic valves by comparing expected versus measured gradients, and identify the echo signs of obstruction versus regurgitation versus normal washout.

  • Classify cardiomyopathy phenotypes: dilated, hypertrophic, restrictive, and infiltrative, listing the defining structural and Doppler features of each.

  • Measure and interpret LV ejection fraction, global longitudinal strain when available, and diastolic function parameters per current guidelines.

  • Differentiate constrictive pericarditis from restrictive cardiomyopathy using respiratory variation, annulus reversus, and septal bounce.

  • Recognize echo findings of cardiac amyloidosis, hypertrophic cardiomyopathy with obstruction, and left ventricular noncompaction.

Your checkpoint

A side-by-side diagnostic comparison chart for five cardiomyopathy phenotypes plus a completed 20-item image-free vignette set on prosthetic valves and cardiomyopathies scored at 80% or better.

Week 7

Cardiomyopathy, pericardial disease, and congenital/acquired pathology

  • Detect and grade pericardial effusion, and identify the echo signs of tamponade physiology including chamber collapse and IVC plethora.

  • Identify common congenital lesions on echo: atrial and ventricular septal defects, bicuspid aortic valve, coarctation, and patent ductus arteriosus.

  • Characterize cardiac masses by location, attachment, mobility, and acoustic properties to separate thrombus, vegetation, and tumor.

  • Apply the modified Duke echocardiographic criteria to a suspected endocarditis case.

  • Recognize aortic dissection, aortic aneurysm, and sinus of Valsalva findings on the suprasternal and parasternal views.

Your checkpoint

A 10-case pathology log covering effusion/tamponade, congenital shunt, mass, and endocarditis, each with findings, differential, and the single measurement that most changed the diagnosis.

Week 8

Cardiac anatomy and physiology & Ultrasound physics and instrumentation & Two-dimensional, M-mode, and Doppler acquisition technique & Valvular heart disease and hemodynamics & Cardiomyopathy, pericardial disease, and congenital/acquired pathology

  • Re-audit all prior self-quizzes and error logs, and rewrite every missed concept as a correct, testable statement.

  • Complete two timed full-length practice exams under exam conditions and analyze misses by domain.

  • Drill the highest-error domain with targeted recalculation and re-derivation rather than rereading.

  • Rehearse rapid recall of severity thresholds, normal reference values, and guideline cutoffs without notes.

Your checkpoint

A final one-page personal summary sheet of thresholds, formulas, and self-identified weak points, plus practice exam scores logged by domain with a written remediation plan for the two weakest domains.

Milestones

Week 2: Score 80% or better on the cumulative anatomy and physics quiz and correctly explain five artifacts and their fixes without notes.

Week 4: Produce a complete aortic stenosis severity grading for three cases using velocity, gradient, and continuity-equation area, with no arithmetic errors.

Week 6: Score 80% or better on the cardiomyopathy and prosthetic valve vignette set and correctly separate constriction from restriction in two of two cases.

Week 8: Score 75% or better on both timed full-length practice exams with no domain below 65%, and have a written remediation plan for the two weakest domains.

Adult Echocardiography (AE) exam day

Your checklist

Two valid forms of identification

Bring at least one government-issued photo ID with a signature and a name that matches your registration exactly (including middle name/initial and hyphenation). A second ID is often requested at testing centers, so bring two. Confirm the exact ID requirements for your testing vendor with the provider before test day.

Appointment confirmation / authorization to test

Print or save the scheduling confirmation email and any candidate/eligibility number the testing vendor issued. Having the confirmation number speeds up check-in if there is a records discrepancy.

Confirmed testing center logistics

Know the exact address, building entrance, floor/suite, parking or transit options, and the vendor's arrival window (many centers ask candidates to arrive well before the appointment time). Do a dry run or map the route the day before.

Arrival buffer planned

Build in extra time for traffic, parking, and security screening/check-in (photo capture, palm-vein or signature verification, locker assignment). Arriving late can cost you your seat or your fee - confirm the vendor's late-arrival policy with the provider.

Leave prohibited items behind or in the car

Phones, smartwatches, fitness trackers, notes, textbooks, and study cards are almost universally barred from the testing room. Plan where these will go before you walk in; centers typically provide only a small locker.

Comfort layers and reading glasses

Testing rooms are often cold and sessions are long. Bring a light layer you can remove, and any corrective lenses you need for screen reading. Check what outerwear is permitted in the testing room.

Nothing that could be read as a cheat sheet

Do not bring written formulas, normal-value cards, or annotated notes into the center, even to the locker if the vendor prohibits study materials on site. Confirm the vendor's rules on personal items.

Quick self-assessment of exam format

Re-read the official content outline so you know the domain weighting (e.g., normal anatomy and physiology, pathology, instrumentation/physics, patient care) and roughly how many items to expect. Verify the current item count and time limit on the provider's site.

Hydration and light meal timing

Eat a normal meal within a couple of hours of the start. Avoid heavy caffeine if you are already anxious, and avoid large volumes of fluid if break time is limited or must be requested.

Backup plan for technology issues

If you are testing remotely, confirm the platform's system check, webcam, microphone, and a backup internet option, and know the vendor's support phone number before the session starts. In-person candidates can skip this item.

Plan the day

72 hours before

Stop introducing new content. Spend remaining study time on high-yield recall: cardiac chamber and valve anatomy, normal Doppler values you are confident in, pressure half-time and continuity-equation concepts, and the physics relationships (resolution vs. penetration, Nyquist limit, aliasing). Use short, timed practice sets rather than long re-reads.

72 hours before

Confirm the appointment one more time: date, time, time zone, address, and the ID you plan to present. Verify that your name matches your registration exactly; name mismatches are a common cause of check-in problems.

48-72 hours before

Do a light review of image-recognition patterns you can hold in working memory: parasternal long/short axis, apical four/two/three chamber, subcostal, and suprasternal views, and the classic appearances of common pathologies. No new textbooks.

24 hours before

Pack your ID, confirmation, glasses, and layer. Set out clothes and confirm transportation and parking. Note the arrival time you are targeting, working backward from the appointment.

24 hours before

Final light review only: one pass over your own summary sheet or weak-topic list, capped at about 60-90 minutes. Then stop. Get a full night's sleep - sleep protects recall more than an extra hour of cramming.

Morning of

Eat a normal breakfast, avoid excessive caffeine, and arrive at the center with buffer time. Re-read nothing new. If you review at all, limit it to a single concepts list while you wait.

During the test - first minutes

Read the tutorial and confirm the interface: how to flag items, how to review flagged questions, how to move forward and back, and whether answers can be changed. Confirm how to summon the proctor and how breaks are requested.

During the test - first pass

Answer confidently known items quickly to bank time. On image or case-based items, identify the view first, then the finding, then the best answer. If two answers both seem true, pick the one that most directly answers what is asked.

During the test - difficult items

Flag and move on rather than stalling. Eliminate obviously wrong options, then use physiology and physics reasoning on the remainder. Do not change an answer unless you have a specific reason - second-guessing under time pressure usually hurts.

During the test - final minutes

Use remaining time to revisit flagged items only. Confirm no item was left blank if the vendor scores unanswered items as incorrect, and confirm you have submitted/ended the session as instructed before leaving the workstation.

Rules to check

  • Bring identification exactly as required by the vendor and be prepared for ID verification, photographing, and a security screening at check-in. If your ID name does not match your registration, contact the provider before test day rather than at the center.

  • Personal electronic devices, notes, and study materials are not permitted in the testing room. Assume anything on your person could be inspected; ask the proctor before bringing in anything you are unsure about.

  • Break availability, break timing, and whether the clock stops during a break vary by vendor and delivery format. Confirm the break policy for your appointment with the provider before test day, and do not leave the testing area without permission.

  • If you are testing in person, do not communicate with other candidates at any time during the session, and do not write on anything except materials the proctor supplies. Scratch materials, if offered, are usually collected at the end.

  • Scoring is criterion-referenced and reported as a scaled score with a passing standard set by the provider; there is no partial credit for unanswered items in most formats. Confirm the current passing standard, score-report timing, and retake/eligibility window on the official provider site.

  • Know the vendor's policy on rescheduling, cancellation, and late arrival, and the fees attached to each. These policies differ by appointment type - confirm with the provider, and get any exception in writing before test day.

  • If technical problems occur during the session (frozen screen, lost connection, malfunctioning input device), stop and notify the proctor or support line immediately and ask that the incident be documented. Do not attempt to troubleshoot a secure testing platform yourself.

  • Answer every item. If the format allows review, budget your final minutes for flagged questions and verify submission before leaving. Keep track of elapsed time yourself rather than relying on the on-screen clock alone.

Adult Echocardiography (AE) FAQ

How many Adult Echocardiography (AE) practice questions are available?

The practice set has 200 Adult Echocardiography (AE) questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many Adult Echocardiography (AE) flashcards are available?

The flashcard set has 32 Adult Echocardiography (AE) cards. Each card shows the term and its definition.

Which topics does the Adult Echocardiography (AE) study material cover?

The Adult Echocardiography (AE) study material has 5 sections, including Cardiac Anatomy and Physiology: Chambers, Segments, and the Cardiac Cycle, Ultrasound Physics and Instrumentation: Resolution, Doppler, and Artifacts, and Two-Dimensional, M-mode, and Doppler Acquisition Technique.

What format facts does the catalog list for the Adult Echocardiography (AE) exam?

The catalog lists these item types: multiple choice for the Adult Echocardiography (AE) exam.