OK Electrician Practice Test

Oklahoma Electrician Licensing Examination

OK Electrician overview

  • 200 practice questions
  • 32 flashcards
  • 9 study guide topics
  • 40 key terms

What you'll study

  • General Requirements, Definitions, and Inspection (NEC Articles 100, 110)10%
  • Wiring Methods and Materials (NEC Chapter 3)14%
  • Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)14%
  • Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)14%
  • Equipment for General Use (NEC Articles 400-460)12%
  • Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)12%
  • Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)8%
  • Special Systems and Communications Circuits (NEC Chapters 7-8)6%
  • Oklahoma Electrical Licensing Statutes and Administrative Rules10%

The Oklahoma Electrician Licensing Examination is the credentialing exam administered through the state's electrical licensing framework for electricians who want to work legally in Oklahoma as journeymen or contractors. It is aimed at electricians with documented field experience who are ready to demonstrate command of the National Electrical Code and the state's own statutes and administrative rules governing licensing, permits, inspections, and contractor responsibilities. The exam is multiple choice and mixes code-lookup items with calculation and applied-installation scenarios, so it tests both speed with the codebook and the judgment built from real jobs. Content spans general requirements and inspection, wiring methods, overcurrent protection, grounding and bonding, services and feeders, general-use equipment, special occupancies and equipment, motors and air conditioning, limited-energy and communications systems, and Oklahoma licensing law. Because the state updates adopted code editions and administrative rules periodically, confirm the current edition and the current scheduling, fee, and scoring details with the Oklahoma Construction Industries Board before you apply. Preparation works best as a planned cycle: read the adopted code edition and the state rules, tab your codebook for fast reference, then drill calculation-heavy topics such as load, conduit fill, and conductor sizing until lookups and math are automatic. Practice with timed, mixed-topic question sets that require you to open the book rather than answer from memory.

Common mistakes

Answering questions from jobsite habit rather than the Code text - for example picking a 20 A breaker on 14 AWG because 'it never tripped,' or calling a receptacle a 'device' when Article 100 defines it differently.

Years of local practice and informal trade shortcuts create strong 'feel-right' answers that conflict with the Code as adopted. The exam scores the Code language, not field custom.

What to do instead

For every practice item, force yourself to name the article and section that supports the answer before selecting it. Flag any answer you cannot cite, and re-study that section the same day. Keep a running list of 'habit vs. Code' conflicts.

Burning the clock in the index and finishing the last 25–30 questions in a rush, or leaving answers blank when there is no penalty for guessing.

Untabbed books and unfamiliarity with NFPA 70's index structure turn simple lookups into multi-minute searches, and time pressure then causes misreads of 'shall' vs. 'shall be permitted' and of exceptions.

What to do instead

Pre-tab Articles 100, 110, 210, 220, 240, 250, 300, 310, 334, 400, 430, 440 and Tables 310.15(B)(16), 250.66, 250.122, 430.52, 430.250, 430.251, plus Annex D. Practice full 50-question sets against a clock, targeting roughly one minute per item so lookups stay short. Never leave blanks.

Sizing an equipment grounding conductor with Table 250.66 (grounding electrode conductor table) or with the phase-conductor size, instead of sizing it from the rating of the overcurrent device per Table 250.122.

Two nearly identical-looking ampacity tables sit in Article 250 and both key off conductor size, so candidates grab whichever table they find first.

What to do instead

Memorize the decision rule: Table 250.66 → grounding electrode conductor, sized by the largest service/feeder conductor; Table 250.122 → equipment grounding conductor, sized by the overcurrent device rating, with 250.122(B) upsizing when conductors are increased. Drill 20 practice items on each table separately.

Leaving the small-appliance and laundry branch circuits out of the standard service/feeder calculation, or applying the Table 220.42 lighting demand factors to receptacle and appliance loads where they do not belong.

The calculation is a sequence of steps across 220.12, 220.14, 220.40–220.55, and skipping or misordering a step still yields a plausible-looking number.

What to do instead

Work Annex D examples (D1(a), D1(b), and the multifamily example) end to end until the sequence is automatic: general lighting from 220.12, small appliance 1500 VA each from 220.52(A), laundry 1500 VA from 220.52(B), appliance demand from 220.53, then 220.55 for ranges and 220.60 noncoincident loads. Write the step list on a card and use it on every practice problem.

Using nameplate FLA for motor branch-circuit conductors and short-circuit protection instead of the Table 430.248/430.250 full-load current, and omitting the 125% multiplier applied to the largest motor.

Nameplate amperes are what the installer sees on the motor, so they feel authoritative, and the Code's use of separate values for conductors, short-circuit protection, and overload protection is easy to collapse into one number.

What to do instead

Lock in the flow: Table 430.248 (single-phase) or 430.250 (three-phase) FLC → conductors at 125% per 430.22 → branch short-circuit and ground-fault protection per 430.52 → overload protection from the nameplate per 430.32. For a feeder, apply 430.24 (125% of the largest plus the sum of the rest).

Selecting a wiring method that is listed but prohibited in that specific application - NM cable above a suspended ceiling in a non-dwelling occupiable space, NM in a wet or damp location, or flexible cord used as a substitute for fixed wiring.

Each Chapter 3 article has a scope and a 'uses permitted / uses not permitted' pair, and candidates learn the product but not its restrictions.

What to do instead

For every wiring method you study, read the article's Part I (scope, uses permitted, uses not permitted) before the installation details, and build a one-page grid of method vs. permitted/not permitted by location (dry/damp/wet, exposed/concealed, dwelling/non-dwelling, hazardous).

Treating flexible cords and cables under Article 400 as general-purpose wiring - running cord through walls, above ceilings, or as permanent branch-circuit wiring to a fixed appliance.

Cord-connected equipment is everywhere on the job, and cord is convenient, so the 400.12 'uses not permitted' list gets glossed over.

What to do instead

Memorize 400.12 as a hard prohibition list and be able to state that flexible cord must be used only for 400.10 permitted uses (pendants, portable appliances, specific listed appliances, etc.). Tie each 400.10 permitted use to a real piece of equipment so the pairing is concrete.

Confusing Class I Division 1 with Zone 0/Zone 1, or specifying the wrong Chapter 5 wiring method or enclosure for the documented area classification.

NEC Chapter 5 presents two parallel systems (Division and Zone) with different definitions and different permitted wiring methods, and candidates study one and assume the other mirrors it.

What to do instead

Build a side-by-side comparison chart of Class I Division 1 vs. Zone 0/1 vs. Zone 2 with the permitted wiring methods and required protection techniques listed in Articles 501 and 505, and always start hazardous-location problems by writing down the class, division/zone, and group before choosing hardware.

Assuming communications and other Chapter 8 cables must satisfy Chapter 3 wiring methods, or ignoring the separation and environmental-airspace rules when routing them near power conductors.

Chapter 8 is largely permissive - its requirements supplement or modify Chapters 1–7 rather than repeating them - so candidates apply raceway rules that do not govern, or skip 800.133 separation and 300.22(C) air-handling rules entirely.

What to do instead

Read Article 800.1 and the 90.3 relationship note, then commit to memory the 2-inch (or permanent barrier) separation rule in 800.133(A) and the plenum restrictions in 300.22(C). Practice classifying cables by Article (800, 820, 830) before applying any installation rule.

Studying only the NEC and skipping Oklahoma statutes and administrative rules, so questions on license classifications, continuing education, contractor bonding/insurance, permits, and inspection authority are answered cold.

Most study guides and code books are national products that contain no Oklahoma-specific content, so the state material is invisible until exam day.

What to do instead

Obtain the Oklahoma Electrical Licensing Act and the Oklahoma Administrative Code rules for the electrical industry, read them once fully, then annotate and tab them the same way as the NEC. Build flashcards for license types and scopes, renewal and CEU hour requirements, bonding and insurance amounts, and who may pull permits and request inspections.

Exam requirements can change. Confirm current details with the exam provider.

OK Electrician practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Article 100 defines "listed" as equipment, materials, or services that meet which description?

    1. Inspected on the job site and found acceptable by the authority having jurisdiction
    2. Included in a list published by an organization acceptable to the authority having jurisdiction and concerned with product evaluation, where the listing states the item meets a designated standard or has been tested and found suitable for a specified purpose Correct answer.
    3. Approved for one specific installation by the serving electric utility
    4. Marked by the manufacturer as suitable for general electrical use without further evaluation

    Explanation

    Article 100 defines listed in terms of a listing organization acceptable to the AHJ that maintains periodic inspection of production and publishes a list of evaluated items. The listing must state that the item either meets a designated standard or has been tested and found suitable for a specified purpose. Field inspection by the AHJ, manufacturer claims, or utility approval do not meet the definition.

  2. Question 2General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Article 100 defines a continuous load as a load in which the maximum current is expected to continue for how long?

    1. 30 minutes or more
    2. The full 24-hour operating day
    3. 1 hour or more
    4. 3 hours or more Correct answer.

    Explanation

    Article 100 defines a continuous load as one where the maximum current is expected to continue for 3 hours or more. This definition drives the 125 percent sizing rules applied to conductors and overcurrent devices serving such loads. Shorter durations are treated as noncontinuous loads.

  3. Question 3General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Under Article 100, who qualifies as a "qualified person"?

    1. Anyone who has completed a registered apprenticeship program
    2. Anyone holding a journeyman electrician license issued by any state
    3. Anyone designated in writing by the building owner to operate electrical equipment
    4. One who has skills and knowledge related to the construction and operation of the electrical equipment and installations and has received safety training to recognize and avoid the hazards involved Correct answer.

    Explanation

    Article 100 defines a qualified person by demonstrated skills and knowledge plus safety training on the hazards involved, not by a credential alone. Licensing or apprenticeship completion may be evidence of training, but the definition turns on demonstrated ability and hazard recognition. An owner's designation alone does not make a person qualified.

  4. Question 4General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Section 110.12 requires that electrical equipment be installed in which manner?

    1. Only after the permit has been posted on site
    2. At the lowest installed cost consistent with the plans
    3. By a licensed electrical contractor
    4. In a neat and workmanlike manner Correct answer.

    Explanation

    Section 110.12 states that electrical equipment shall be installed in a neat and workmanlike manner. Informational notes describe accepted industry practices such as those published by NECA and other organizations. Licensing, cost, and permit administration are outside the scope of this section.

  5. Question 5General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    What is the minimum required width of the working space in front of electrical equipment?

    1. The width of the equipment or 24 inches, whichever is greater
    2. The width of the equipment or 30 inches, whichever is greater Correct answer.
    3. The width of the equipment or 36 inches, whichever is greater
    4. The width of the equipment or 48 inches, whichever is greater

    Explanation

    Section 110.26(A)(2) requires the working space width to be the width of the equipment or 30 inches, whichever is greater. The space must also permit at least a 90-degree opening of equipment doors or hinged panels. The 30-inch figure is a minimum, not a fixed dimension when the equipment is wider.

  6. Question 6General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    The working space in front of electrical equipment must extend from the floor to what minimum height?

    1. 7 feet
    2. 8 feet
    3. 6 1/2 feet Correct answer.
    4. 5 feet

    Explanation

    Section 110.26(A)(3) requires the working space to extend from grade, floor, or platform to a height of 6 1/2 feet or the height of the equipment, whichever is greater. This headroom applies to the full depth and width of the required working space.

  7. Question 7General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    A 480Y/277-volt panelboard is installed where exposed live parts are on one side of the working space and a grounded metal surface is on the other. What minimum depth of working space is required?

    1. 3 1/2 feet
    2. 5 feet
    3. 3 feet
    4. 4 feet Correct answer.

    Explanation

    For equipment operating at 251 to 600 volts to ground under Condition 2, Table 110.26(A)(1) requires a depth of 4 feet. The 277-volt line-to-ground value places the installation in the 251-to-600-volt column. Condition 3 would require 5 feet, and Condition 1 would require 3 feet.

  8. Question 8General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    What space above electrical equipment must be reserved as dedicated electrical space?

    1. A space 3 feet above the equipment, extending 12 inches beyond its width and depth
    2. A space from the floor to 6 feet above the equipment, with the full width and depth of the equipment Correct answer.
    3. A space 8 feet above the equipment, extending 24 inches beyond its width and depth
    4. A space from the floor to the structural ceiling regardless of height, extending 6 inches beyond the equipment depth

    Explanation

    Section 110.26(E)(1) dedicates the space equal to the width and depth of the equipment and extending from the floor to a height of 6 feet above the equipment or to the structural ceiling, whichever is lower. That dedicated space may not be used for foreign systems such as piping, ducts, or leak-prone equipment.

  9. Question 9General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    How must a disconnecting means for electrical equipment be identified?

    1. It must be marked with the available fault current at its terminals
    2. It must be marked with the date of installation and the name of the installing contractor
    3. It must be legibly marked to indicate its purpose unless it is located and arranged so the purpose is evident Correct answer.
    4. It must be marked with the conductor size and the rating of the overcurrent device

    Explanation

    Section 110.22(A) requires each disconnecting means to be legibly marked to indicate its purpose unless it is located and arranged so its purpose is evident. The marking must be durable enough to withstand the environment. Installation dates, fault current, and conductor sizes are addressed by other sections.

  10. Question 10General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    The arc-flash hazard warning required by 110.16 applies to equipment meeting which description?

    1. Only equipment operating at more than 1000 volts
    2. Equipment supplied through more than one service disconnect
    3. Equipment in other than dwelling units that is likely to require examination, adjustment, servicing, or maintenance while energized Correct answer.
    4. Any equipment installed outdoors in a wet location, regardless of voltage

    Explanation

    Section 110.16 requires a field-applied warning label on equipment that is likely to require examination, adjustment, servicing, or maintenance while energized, and the requirement applies to installations other than dwelling units. The label alerts qualified persons to arc-flash hazard and available information. It is not limited by voltage class or by the number of service disconnects.

  11. Question 11General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Section 110.14 addresses tightening of electrical connections. Which practice complies?

    1. Tightening terminals to the torque marked on the equipment or in the manufacturer's instructions, using a calibrated torque tool where the instructions require it Correct answer.
    2. Tightening terminals to the maximum torque the terminal material can withstand
    3. Tightening terminals to the value printed in the connector catalog for the largest conductor the terminal accepts
    4. Tightening terminals only as firmly as can be done by hand plus one-quarter turn

    Explanation

    Section 110.14(D) requires terminals to be tightened to the torque indicated on the equipment or in the manufacturer's instructions, and where a tightening torque is indicated, a calibrated torque tool must be used unless the instructions specify otherwise. Connection torque is a listing and labeling condition for the terminal and conductor combination.

  12. Question 12General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Equipment intended to interrupt current at fault levels must have an interrupting rating at nominal circuit voltage that is at least equal to what value?

    1. The available fault current at the load terminals of the equipment
    2. The rating of the next upstream overcurrent device
    3. The ampacity of the conductors supplying the equipment
    4. The maximum current that is available at the line terminals of the equipment Correct answer.

    Explanation

    Section 110.9 requires equipment intended to interrupt current at fault levels to have an interrupting rating at nominal circuit voltage at least equal to the current available at its line terminals. This ensures the device can safely clear a fault at the point where it is installed. Conductor ampacity and upstream device ratings do not establish that value.

  13. Question 13General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Section 110.24 requires service equipment to be legibly marked in the field with which value?

    1. The interrupting rating of the service disconnecting means
    2. The calculated arc-flash boundary distance
    3. The maximum available fault current Correct answer.
    4. The minimum available fault current at the load terminals

    Explanation

    Section 110.24(A) requires service equipment in other than dwelling units to be marked with the maximum available fault current. The marking must be durable and be updated when system changes alter the available fault current. Arc-flash boundaries and device ratings are not what this section requires on the label.

  14. Question 14General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    According to 110.26(B), how may the working space required in front of electrical equipment be used?

    1. It shall not be used for storage Correct answer.
    2. It may be used for storage if a clear path of at least 24 inches is maintained
    3. It shall be used to store the maintenance equipment for the building
    4. It may be used to store spare parts if the parts are noncombustible

    Explanation

    Section 110.26(B) states that working space required by the section shall not be used for storage. The space must remain clear so that qualified persons can safely work on the equipment. When normally enclosed live parts are exposed for servicing, the working space must also be suitably guarded if it is in a passageway or general open space.

  15. Question 15General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    For switchgear rated 1200 amperes or more and more than 6 feet wide, 110.26(C)(2) generally requires which arrangement?

    1. Two entrances, one at each end of the working space Correct answer.
    2. A single entrance at least 24 inches wide located at one end of the equipment
    3. Two entrances only when the equipment is rated more than 1000 volts
    4. Three entrances evenly spaced along the working space

    Explanation

    Section 110.26(C)(2) requires large equipment rated 1200 amperes or more and over 6 feet wide to have at least two means of egress, one at each end of the working space. Limited exceptions permit a single entrance under specified conditions, such as unobstructed exit travel. The requirement addresses the difficulty of escaping a large equipment lineup in an emergency.

  16. Question 16General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Section 110.26(D) requires illumination for working spaces about which equipment?

    1. Only equipment located in rooms without natural light
    2. Indoor service equipment, switchboards, switchgear, panelboards, and motor control centers Correct answer.
    3. Only equipment operating at more than 600 volts
    4. Only equipment rated 1200 amperes or more

    Explanation

    Section 110.26(D) requires illumination to be provided for all working spaces about indoor service equipment, switchboards, switchgear, panelboards, and motor control centers. The lighting must not be controlled solely by an automatic means that could leave the space dark while someone is working. Voltage, room daylight, and ampere rating do not limit the requirement.

  17. Question 17General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Working space is provided in front of a 208Y/120-volt panelboard with exposed live parts on one side and a concrete block wall directly opposite. Which condition governs the required depth of working space?

    1. The depth cannot be determined without the available fault current
    2. Condition 2 Correct answer.
    3. Condition 3
    4. Condition 1

    Explanation

    Table 110.26(A)(1) uses Condition 2 where exposed live parts are on one side and grounded parts are on the other, and concrete, brick, and tile walls are treated as grounded. Condition 1 requires the opposite side to be free of live or grounded parts, while Condition 3 requires exposed live parts on both sides. Fault current does not affect which condition applies.

  18. Question 18General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Which statement correctly distinguishes the grounded conductor from the equipment grounding conductor?

    1. Both conductors must be identified with white or gray insulation over their entire length
    2. The grounded conductor is bonded to equipment enclosures and normally carries no current
    3. The grounded conductor is a circuit conductor that is intentionally grounded and carries current in normal operation, while the equipment grounding conductor normally carries no current Correct answer.
    4. The equipment grounding conductor carries the circuit's unbalanced current during normal operation

    Explanation

    Article 100 defines the grounded conductor as a system or circuit conductor that is intentionally grounded and that normally carries current, while the equipment grounding conductor is the conductive path that connects normally non-current-carrying metal parts and normally carries current only under fault conditions. Confusing the two roles leads to improper bonding and neutral identification.

  19. Question 19General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Section 110.10 requires that overcurrent protective devices, total impedance, component short-circuit current ratings, and other circuit characteristics be selected and coordinated so that which result is achieved?

    1. The circuit protective devices will clear a fault without extensive damage to the circuit components Correct answer.
    2. The conductors are protected against overloads only
    3. The equipment grounding conductor will carry fault current continuously
    4. The available fault current is reduced to zero at the load end of the circuit

    Explanation

    Section 110.10 requires protective devices, impedance, and short-circuit current ratings to be selected and coordinated so the circuit protective devices clear a fault without extensive damage to circuit components. This is a performance requirement separate from the interrupting rating rule of 110.9. It also covers components listed for use only on circuits capable of delivering no more than a specified fault current.

  20. Question 20General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

    Which option best matches the Article 100 definition of "readily accessible"?

    1. Reachable after removing a bolted panel cover with a screwdriver
    2. Reachable from a portable ladder kept in a nearby utility closet
    3. Capable of being reached quickly for operation, renewal, or inspections without climbing over or removing obstacles or using portable ladders Correct answer.
    4. Reachable only by qualified persons wearing arc-rated protective equipment

    Explanation

    Article 100 defines readily accessible as capable of being reached quickly for operation, renewal, or inspections without requiring those to whom ready access is requisite to climb over or remove obstacles or to resort to portable ladders. The concept concerns speed and freedom from obstacles, not who is permitted to gain access. Locations requiring tools, ladders, or removal of building finishes are not readily accessible.

  21. Question 21Wiring Methods and Materials (NEC Chapter 3)

    Type NM cable must be secured within what maximum distance of a box or fitting, and at what maximum intervals along the run?

    1. Within 12 in of the box and at intervals not exceeding 4 1/2 ft Correct answer.
    2. Within 8 in of the box and at intervals not exceeding 4 1/2 ft
    3. Within 12 in of the box and at intervals not exceeding 6 ft
    4. Within 6 in of the box and at intervals not exceeding 10 ft

    Explanation

    Section 334.30 requires Type NM cable to be secured and supported at intervals not exceeding 4 1/2 ft and within 12 in of every box, cabinet, or fitting. Limited exceptions exist, such as cable fished into a concealed space or cable secured by listed staples in accessible attic spaces. Both the interval and the box distance must be satisfied.

  22. Question 22Wiring Methods and Materials (NEC Chapter 3)

    Electrical metallic tubing must be supported at intervals not exceeding ___ and within ___ of each box or termination fitting.

    1. 12 ft; 4 ft
    2. 10 ft; 3 ft Correct answer.
    3. 6 ft; 3 ft
    4. 10 ft; 5 ft

    Explanation

    Section 358.30 limits EMT support intervals to 10 ft and requires a support within 3 ft of each box, conduit body, or termination fitting. The 3 ft rule keeps the raceway rigid near terminations so the fitting is not stressed. Both conditions must be met.

  23. Question 23Wiring Methods and Materials (NEC Chapter 3)

    How much box volume must be counted for each 12 AWG conductor in a box?

    1. 2.25 cu in Correct answer.
    2. 2.00 cu in
    3. 1.75 cu in
    4. 2.50 cu in

    Explanation

    Table 314.16(B) assigns a volume allowance based on conductor size: 2.0 cu in for 14 AWG, 2.25 cu in for 12 AWG, and 2.5 cu in for 10 AWG. Each conductor that enters the box, plus specified items counted as conductors, uses one allowance. The total must not exceed the volume marked on the box.

  24. Question 24Wiring Methods and Materials (NEC Chapter 3)

    Each free conductor in an outlet or junction box must be at least ___ long, and must extend at least ___ beyond the opening of the box.

    1. 6 in; 1 in
    2. 6 in; 3 in Correct answer.
    3. 3 in; 6 in
    4. 4 in; 2 in

    Explanation

    Section 300.14 requires at least 6 in of free conductor measured from the point in the box where it emerges from its raceway or cable sheath. At least 3 in of that conductor must extend outside the box opening. This provides enough conductor to splice or terminate equipment.

  25. Question 25Wiring Methods and Materials (NEC Chapter 3)

    What is the maximum total number of degrees of bends permitted in a run of raceway between pull points?

    1. 360 degrees Correct answer.
    2. 90 degrees
    3. 270 degrees
    4. 180 degrees

    Explanation

    Sections such as 358.26 for EMT and 344.26 for rigid metal conduit limit the bends between boxes, conduit bodies, or fittings to a total of 360 degrees. This includes offsets, kicks, and saddle bends. The limit exists so the raceway can still be pulled without damaging conductors.

  26. Question 26Wiring Methods and Materials (NEC Chapter 3)

    Type UF cable is listed for installation in which locations?

    1. Wet, damp, and dry locations Correct answer.
    2. Dry and damp locations only
    3. Dry locations only
    4. Damp locations only

    Explanation

    Article 340 permits Type UF cable in wet, damp, and dry locations, and it is permitted for direct burial where the burial requirements of 300.5 are met. The conductors are enclosed in a moisture-resistant assembly suitable for underground use. It is also permitted in corrosive locations where identified for the purpose.

  27. Question 27Wiring Methods and Materials (NEC Chapter 3)

    Flexible metal conduit must be securely fastened within what maximum distance of a box or fitting?

    1. 6 in
    2. 18 in
    3. 12 in Correct answer.
    4. 24 in

    Explanation

    Section 348.30 requires FMC to be fastened within 12 in of each box or fitting and at intervals not exceeding 4 1/2 ft, with exceptions for short lengths. The 12 in dimension keeps the flexible raceway from pulling out of terminations. Listed fittings and supports must be used.

  28. Question 28Wiring Methods and Materials (NEC Chapter 3)

    Type AC cable is distinguished from Type MC cable by the presence of which feature?

    1. A bare copper equipment grounding conductor
    2. A bare aluminum bonding strip in contact with the armor Correct answer.
    3. A plastic inner jacket around the circuit conductors
    4. An overall nonmetallic outer sheath

    Explanation

    Type AC cable contains a bare aluminum bonding strip that is in intimate contact with the interlocked metal armor, so the armor assembly serves as the equipment grounding path. Type MC cable normally relies on a separate insulated equipment grounding conductor or an armor listed for grounding. That bonding strip is the defining internal difference between the two cable types.

  29. Question 29Wiring Methods and Materials (NEC Chapter 3)

    Type MC cable must be supported at intervals not exceeding ___ and within ___ of a box or fitting.

    1. Every 6 ft and within 6 in
    2. Every 4 1/2 ft and within 12 in
    3. Every 6 ft and within 12 in Correct answer.
    4. Every 10 ft and within 3 ft

    Explanation

    Section 330.30 requires Type MC cable to be secured and supported at intervals not exceeding 6 ft and within 12 in of every box or fitting. The longer interval reflects the greater rigidity of the metal-clad assembly compared with NM or AC cable. Exception provisions apply to certain short lengths and to cable in cable trays.

  30. Question 30Wiring Methods and Materials (NEC Chapter 3)

    Where conductors are spliced in a run of EMT, the splice must be ___.

    1. left accessible inside the raceway
    2. supported within 12 in of the splice
    3. enclosed in a box or conduit body Correct answer.
    4. made with an irreversible compression tool

    Explanation

    Section 300.15 requires a box, conduit body, or other listed enclosure at every splice, pull point, or termination point. A splice cannot simply be pulled into the raceway because the enclosure keeps the connection protected and accessible. Support of the splice itself is not what the rule requires.

  31. Question 31Wiring Methods and Materials (NEC Chapter 3)

    The conductors, splices, and taps in a metal wireway may fill the interior cross-sectional area to a maximum of ___.

    1. 20 percent Correct answer.
    2. 25 percent
    3. 40 percent
    4. 60 percent

    Explanation

    Section 376.22 limits conductors, splices, and taps in a wireway to 20 percent of the interior cross-sectional area. The generous physical space of a wireway is intended partly for heat dissipation and future additions. Ampacity adjustment for current-carrying conductors also applies once the count exceeds 30 in a cross section.

  32. Question 32Wiring Methods and Materials (NEC Chapter 3)

    A straight run of 1 in Schedule 40 PVC conduit must be supported at intervals not exceeding ___.

    1. 3 ft Correct answer.
    2. 5 ft
    3. 3 1/2 ft
    4. 4 ft

    Explanation

    Table 352.30 gives support intervals that increase with conduit size: 3 ft for 1/2 through 1 in, 3 1/2 ft for 1 1/4 through 2 in, 4 ft for 2 1/2 through 3 in, 4 1/2 ft for 3 1/2 through 5 in, and 5 ft for 6 in. PVC needs closer support than metal raceways because it is less rigid. Section 352.30 also requires a support within 3 ft of each box.

  33. Question 33Wiring Methods and Materials (NEC Chapter 3)

    A cable is run through a bored hole less than 1 1/4 in from the nearest edge of a wood framing member. Protection must be provided by a steel plate not less than ___ thick.

    1. 1/8 in
    2. 1/32 in
    3. 1/4 in
    4. 1/16 in Correct answer.

    Explanation

    Section 300.4(A)(1) requires a steel plate at least 1/16 in thick when a hole or notch is less than 1 1/4 in from the nearest edge of a stud, joist, or similar member. The plate prevents nails and screws from penetrating the cable or raceway. Protection may be omitted where the cable is otherwise listed for the condition.

  34. Question 34Wiring Methods and Materials (NEC Chapter 3)

    Type UF cable supplied by a 120/240 V, 20 A branch circuit is direct buried beneath a one-family dwelling driveway used only for dwelling-related purposes. What is the minimum cover?

    1. 24 in
    2. 6 in
    3. 12 in
    4. 18 in Correct answer.

    Explanation

    Table 300.5 contains a specific row for one- and two-family dwelling driveways and outdoor parking areas used only for dwelling-related purposes, requiring 18 in of cover. The general 12 in allowance applies to residential branch circuits not run beneath a driveway. Deeper cover is required under public streets and roads.

  35. Question 35Wiring Methods and Materials (NEC Chapter 3)

    Cut ends of rigid metal conduit and intermediate metal conduit must be ___ before the raceway is assembled.

    1. painted to prevent corrosion
    2. chamfered with a file to a 45 degree bevel
    3. threaded over the full length of the cut
    4. reamed or otherwise finished to remove burrs Correct answer.

    Explanation

    Sections 344.28 and 342.28 require all cut ends to be reamed or otherwise finished to remove rough edges before the conduit is installed. Burrs left in the raceway can cut conductor insulation during a pull. The requirement applies to both field cuts and factory cuts.

  36. Question 36Wiring Methods and Materials (NEC Chapter 3)

    An expansion fitting must be installed in a run of rigid PVC conduit where thermal expansion and contraction will cause a length change of at least ___.

    1. 1/4 in Correct answer.
    2. 1/8 in
    3. 1/2 in
    4. 1 in

    Explanation

    Section 352.44 requires expansion fittings to compensate for thermal expansion and contraction where the length change will be 1/4 in or more. The change is calculated from the run length, the temperature differential, and the expansion coefficient of the PVC. Runs with smaller movement do not require expansion fittings.

  37. Question 37Wiring Methods and Materials (NEC Chapter 3)

    The radius of the inner edge of a bend in Type NM cable must not be less than ___ the diameter of the cable.

    1. 8 times
    2. 10 times
    3. 3 times
    4. 5 times Correct answer.

    Explanation

    Section 334.24 requires bends in NM cable to have an inner radius of at least five times the cable diameter. The same rule appears for other cable articles and protects the conductors and jacket from damage. Bends made tighter than this can crack the sheath or stress the conductors.

  38. Question 38Wiring Methods and Materials (NEC Chapter 3)

    Which of the following locations is acceptable for the installation of electrical metallic tubing?

    1. Where subject to severe physical damage
    2. In a wet location Correct answer.
    3. In an area subject to severe corrosive vapors
    4. In a hazardous (classified) location

    Explanation

    Article 358 permits EMT to be installed exposed, concealed, and in wet locations, provided corrosion-resistant supports and fittings are used. Section 358.12 prohibits EMT where it would be subject to severe physical damage, in hazardous (classified) locations, and where it would be subject to corrosive conditions that damage the tubing. Wet locations therefore remain an acceptable use.

  39. Question 39Wiring Methods and Materials (NEC Chapter 3)

    Boxes and conduit bodies must be installed so that ___.

    1. their locations are recorded in the panelboard directory
    2. the wiring inside is accessible without removing building finish Correct answer.
    3. the covers are mounted a minimum of 12 in above the floor
    4. they are supported independently of the raceway system

    Explanation

    Section 314.29 requires boxes and conduit bodies to be installed so that the wiring inside is accessible without removing any part of the building finish or structure. Accessibility permits future inspection, repair, and modification. Support requirements in 314.23 are a separate concern.

  40. Question 40Wiring Methods and Materials (NEC Chapter 3)

    For a straight pull, the length of a box or conduit body in the direction of the pull must be at least ___ the trade size of the largest raceway.

    1. four times
    2. six times
    3. eight times Correct answer.
    4. ten times

    Explanation

    Section 314.28(A)(1) requires the length of a box or conduit body in the direction of a straight pull to be at least eight times the trade size of the largest raceway. The dimension is measured from the raceway entry to the opposite wall. This space allows conductors to be pulled without damage.

  41. Question 41Wiring Methods and Materials (NEC Chapter 3)

    The same conductors enter a box through a 3 in raceway on one wall and leave through a 2 in raceway on an adjacent wall. What is the minimum required distance between the two raceway entries?

    1. 24 in
    2. 18 in Correct answer.
    3. 12 in
    4. 16 in

    Explanation

    For an angle pull, Section 314.28(A)(2) requires the distance between raceway entries enclosing the same conductors to be at least six times the trade size of the larger raceway. Here 6 times 3 in equals 18 in. The distance is measured along the inside of the box between the nearest edges of the raceways.

  42. Question 42Wiring Methods and Materials (NEC Chapter 3)

    Six current-carrying THHN conductors are installed in a single raceway. The ampacity of each conductor must be adjusted to what percentage of its Table 310.16 value?

    1. 80 percent Correct answer.
    2. 75 percent
    3. 50 percent
    4. 70 percent

    Explanation

    Table 310.15(C)(1) requires ampacity adjustment when more than three current-carrying conductors are installed together. For four through six conductors the adjustment factor is 80 percent. Conductors that are not current-carrying, such as a neutral in a balanced multiwire branch circuit, are generally excluded from the count.

  43. Question 43Wiring Methods and Materials (NEC Chapter 3)

    A 4 in by 1 1/2 in square metal box is used for a splice. It contains no cable clamps, no devices, and no equipment grounding conductors. How many 12 AWG conductors may the box contain?

    1. Ten
    2. Nine Correct answer.
    3. Eleven
    4. Eight

    Explanation

    Table 314.16(A) assigns a 4 in by 1 1/2 in square box a volume of 21.0 cu in. Each 12 AWG conductor requires 2.25 cu in under Table 314.16(B), and 21.0 divided by 2.25 equals 9.33, which rounds down to 9 conductors. Clamps, devices, and grounding conductors would consume additional volume.

  44. Question 44Wiring Methods and Materials (NEC Chapter 3)

    Type UF cable is direct buried beneath a public street. What minimum cover is required?

    1. 18 in
    2. 24 in Correct answer.
    3. 30 in
    4. 12 in

    Explanation

    Table 300.5 requires 24 in of cover for direct-buried cables and conductors installed under streets, highways, roads, alleys, driveways, and parking lots. The reduced residential allowances do not apply to public roadways. Raceways in those locations are permitted shallower cover than direct-buried cable.

  45. Question 45Wiring Methods and Materials (NEC Chapter 3)

    Where all other conditions of the NEC are satisfied, flexible metal conduit may serve as an equipment grounding conductor only if its length does not exceed ___.

    1. 3 ft
    2. 4 1/2 ft
    3. 6 ft Correct answer.
    4. 10 ft

    Explanation

    Article 348 permits FMC to serve as an equipment grounding conductor only where the conditions of 250.118 are met, including a length limit of 6 ft and termination in listed fittings. Beyond that length the fault-current path through the flexible armor is not considered reliable. A separate equipment grounding conductor is then required.

  46. Question 46Wiring Methods and Materials (NEC Chapter 3)

    Liquidtight flexible nonmetallic conduit (Type LFNC-B) is permitted to be installed in which of the following situations?

    1. Encased within a concrete slab that is in direct contact with the earth
    2. Exposed on a building exterior where it is subject to physical damage
    3. Inside a concealed location within a plenum ceiling without any listing marking
    4. Buried directly in the earth where the conduit is listed and marked for direct burial Correct answer.

    Explanation

    Type LFNC-B is a listed raceway that may be installed in exposed, concealed, and underground locations when the raceway is listed and marked for the specific use, including direct burial. Where subject to physical damage, the raceway must be protected by guards or be of a type identified for the condition.

  47. Question 47Wiring Methods and Materials (NEC Chapter 3)

    A 1 1/2 in trade size rigid metal conduit nipple, 18 in long, is installed between two cabinets to protect a short raceway run. What minimum number of supports is required for this nipple?

    1. Two supports, one at each end
    2. No support is required for the nipple Correct answer.
    3. One support is required at the midpoint of the nipple
    4. Supports are required every 5 ft along the nipple

    Explanation

    Rigid metal conduit must be supported in accordance with the support spacing table, but a nipple of 3 ft or less in length is exempt from the support requirements. Because the 18 in nipple is shorter than 3 ft, no support is needed.

  48. Question 48Wiring Methods and Materials (NEC Chapter 3)

    A run of nonmetallic sheathed cable is installed through the attic of a dwelling and must pass across the top of ceiling joists where the attic is accessible only by a scuttle. Which installation satisfies the physical protection requirement?

    1. The cable is secured to the top edge of the joists with staples spaced 12 in apart
    2. The cable is laid across the top of the joists and secured with cable ties at each joist
    3. The cable is run through bored holes in the joists instead of across their tops Correct answer.
    4. The cable is run across the joists and covered with a 1/4 in plywood walkway

    Explanation

    In attics and roof spaces that are accessible, cable run across the top of floor joists, or within 6 ft of the scuttle, must be protected from physical damage; the usual acceptable method is to run the cable through bored holes in the framing members. Running the cable through holes in the joists avoids the exposure entirely.

  49. Question 49Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Which of the following is a standard ampere rating for an inverse-time circuit breaker, as listed in NEC 240.6(A)?

    1. 130 A
    2. 110 A Correct answer.
    3. 115 A
    4. 145 A

    Explanation

    Section 240.6(A) lists the standard ampere ratings for fuses and inverse-time circuit breakers, and 110 A appears in that list. The values 115 A, 130 A, and 145 A are not standard ratings, so a device so marked would not be a standard-size overcurrent device.

  50. Question 50Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A homeowner asks you to install a panelboard containing branch-circuit breakers inside a bathroom. How does the NEC address this?

    1. Permitted where it is installed at least 3 ft from the bathtub
    2. Permitted where the panelboard is protected by a GFCI receptacle
    3. Permitted where the panelboard enclosure has a lockable cover
    4. Prohibited in bathrooms by 240.24 Correct answer.

    Explanation

    Section 240.24 identifies bathrooms as a location where overcurrent devices are not permitted, in addition to clothes closets and similar spaces. GFCI protection, clearance, or a lockable cover does not change that prohibition.

  51. Question 51Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A ground ring grounding electrode must consist of at least how many feet of bare copper conductor not smaller than 2 AWG?

    1. 15 ft
    2. 10 ft
    3. 20 ft Correct answer.
    4. 25 ft

    Explanation

    Section 250.52(A)(4) describes a ground ring as at least 20 ft of bare copper conductor not smaller than 2 AWG, buried at least 2.5 ft below the surface. Shorter lengths of 2 AWG copper do not qualify as a ground ring.

  52. Question 52Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Under 240.4(D), the maximum overcurrent protection for a 14 AWG copper branch-circuit conductor is:

    1. 15 A Correct answer.
    2. 10 A
    3. 25 A
    4. 20 A

    Explanation

    Section 240.4(D)(3) limits 14 AWG copper conductors to 15 A overcurrent protection unless a specific permission elsewhere in the Code applies. The higher ampacities that might be calculated for 14 AWG conductors cannot be used to justify a larger standard breaker for general branch-circuit wiring.

  53. Question 53Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Which of the following wiring methods is permitted to serve as an equipment grounding conductor?

    1. Liquidtight flexible nonmetallic conduit
    2. Schedule 40 PVC conduit
    3. Electrical metallic tubing Correct answer.
    4. Rigid nonmetallic conduit

    Explanation

    Section 250.118 lists the conductors and raceways recognized as equipment grounding conductors, and electrical metallic tubing is one of them. Nonmetallic raceways have no metal path for fault current and therefore cannot serve as the equipment grounding conductor.

  54. Question 54Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    What is the minimum size copper equipment grounding conductor required for a branch circuit protected by a 60 A overcurrent device?

    1. 12 AWG
    2. 10 AWG Correct answer.
    3. 14 AWG
    4. 8 AWG

    Explanation

    Table 250.122 sizes the equipment grounding conductor by the rating of the overcurrent device protecting the circuit, and a 60 A device requires 10 AWG copper. The 14 AWG and 12 AWG sizes apply to 15 A and 20 A circuits respectively.

  55. Question 55Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Under NEC 240.22, an overcurrent device is prohibited from being connected in series with:

    1. a circuit conductor that is intentionally grounded Correct answer.
    2. the equipment grounding conductor of a feeder
    3. any ungrounded circuit conductor
    4. an ungrounded conductor of a 3-phase motor branch circuit

    Explanation

    Section 240.22 prohibits overcurrent devices in series with any conductor that is intentionally grounded, because opening that conductor would leave equipment energized while appearing de-energized. Overcurrent protection is instead placed in the ungrounded conductors.

  56. Question 56Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A rod-type grounding electrode must have a minimum length of:

    1. 6 ft
    2. 8 ft Correct answer.
    3. 4 ft
    4. 10 ft

    Explanation

    Section 250.52(A)(5) requires rod and pipe electrodes to be at least 8 ft in length, and 250.53 requires the rod to be driven so that 8 ft is in contact with the soil. A shorter rod does not qualify as a code-compliant electrode.

  57. Question 57Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A grounding electrode conductor is installed in 15 ft of rigid metal conduit between the service equipment and a ground rod. What must be done?

    1. No bonding is needed if the raceway run is short
    2. Replace the ferrous raceway with nonmetallic conduit
    3. Bond the raceway only at the ground rod end
    4. Bond both ends of the raceway to the conductor Correct answer.

    Explanation

    Section 250.64(E) requires ferrous metal raceways enclosing a grounding electrode conductor to be bonded at each end to the grounding electrode conductor. This keeps the raceway from acting as a parallel, high-impedance path and prevents inductive choking of the conductor.

  58. Question 58Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A feeder conductor that does not supply a multioutlet receptacle circuit has an ampacity of 65 A and carries a calculated load of 60 A. What is the largest standard overcurrent device permitted by 240.4(B)?

    1. 50 A
    2. 60 A
    3. 70 A Correct answer.
    4. 80 A

    Explanation

    Because 65 A is not a standard ampere rating, 240.4(B) permits the next higher standard rating, which is 70 A, provided the rating does not exceed 800 A and the conductor ampacity is not less than the load. A 70 A device therefore protects this feeder.

  59. Question 59Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Which method is permitted for splicing a grounding electrode conductor?

    1. A set-screw connector inside a junction box
    2. A terminal lug bolted to a removable cover
    3. An irreversible compression connector Correct answer.
    4. A split-bolt connector in an accessible location

    Explanation

    Section 250.64(C) requires grounding electrode conductors to be continuous and permits splicing only by irreversible means such as listed compression connectors or exothermic welding. Accessible mechanical connections are not permitted for this conductor.

  60. Question 60Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A 20 A branch circuit is wired with 12 AWG copper conductors. Because of voltage drop the conductors are increased to 10 AWG. What minimum copper equipment grounding conductor is required?

    1. 8 AWG
    2. 12 AWG
    3. 14 AWG
    4. 10 AWG Correct answer.

    Explanation

    Section 250.122(B) requires the equipment grounding conductor to be increased in size proportionally whenever the circuit conductors are increased above the size required by the Code. Since the ungrounded conductors went from 12 AWG to 10 AWG, the equipment grounding conductor must also be 10 AWG copper.

  61. Question 61Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    An 8 ft feeder tap is protected by a 400 A overcurrent device ahead of it, and it does not fall under the transformer or high-bay lighting tap rules. What minimum ampacity must the tap conductors have under 240.21(B)(1)?

    1. 200 A
    2. 40 A Correct answer.
    3. 20 A
    4. 100 A

    Explanation

    Section 240.21(B)(1) permits a tap up to 10 ft long where the tap conductor ampacity is at least one-tenth of the rating of the overcurrent device ahead of the tap and not less than the load served. One-tenth of 400 A is 40 A.

  62. Question 62Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A single ground rod is driven and its resistance to earth measures 40 ohms. What does the NEC require?

    1. An additional electrode must be installed Correct answer.
    2. A 25-ohm resistor in series will correct it
    3. Nothing further, since the reading is below 50 ohms
    4. The rod must be replaced with a longer one

    Explanation

    Section 250.53(A)(2) permits a single rod, pipe, or plate electrode only where it has a resistance to earth of 25 ohms or less; otherwise it must be supplemented by at least one additional electrode. A reading of 40 ohms exceeds that threshold, so a second electrode of a type listed in 250.52 is required.

  63. Question 63Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A feeder runs from a dwelling to a panelboard in a detached garage and includes an equipment grounding conductor. How is the grounded conductor terminated at the garage panelboard?

    1. On a terminal bar that is isolated from the enclosure Correct answer.
    2. Bonded to the panelboard enclosure at the neutral bar
    3. Connected to the equipment grounding conductor terminal bar
    4. Bonded to the grounding electrode at the garage

    Explanation

    For a feeder to a separate building that includes an equipment grounding conductor, 250.32 requires the grounded conductor to be kept isolated from the equipment grounding system at the load end. Bonding the grounded conductor to the enclosure would create a parallel return path on the grounding conductors.

  64. Question 64Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    What must be provided at the service equipment so that communications and antenna system grounding conductors can be bonded?

    1. A main bonding jumper
    2. A surge arrester
    3. A grounding electrode conductor tap
    4. An intersystem bonding termination Correct answer.

    Explanation

    Section 250.94 requires an intersystem bonding termination, or an equivalent listed means, at the service equipment for connecting communications and other systems to the grounding electrode system. It provides an accessible point for those systems without disturbing existing grounding connections.

  65. Question 65Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Which description matches the effective ground-fault current path required by 250.4(A)(5)?

    1. Permanent and of low impedance Correct answer.
    2. Insulated and of small ampacity
    3. Continuous and of high reactance
    4. Temporary and of high resistance

    Explanation

    Section 250.4(A)(5) requires the effective ground-fault current path to be permanent and electrically continuous, to have sufficiently low impedance to facilitate the operation of overcurrent devices, and to be capable of carrying fault current. High-resistance or high-reactance paths would prevent prompt clearing of a ground fault.

  66. Question 66Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Unless shown to be impracticable, enclosures for overcurrent devices must be mounted in which position?

    1. Horizontally
    2. In any position the manufacturer lists
    3. At a 45-degree angle
    4. Vertically Correct answer.

    Explanation

    Section 240.33 requires enclosures for overcurrent devices to be mounted in a vertical position unless that is shown to be impracticable. Vertical mounting preserves the intended meaning of the ON and OFF positions of the operating handles.

  67. Question 67Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A metal underground water pipe is used as a grounding electrode. What does 250.53(D)(2) require?

    1. It may be used only if it is at least 20 ft long
    2. It must be supplemented by an additional electrode Correct answer.
    3. It must be replaced by a concrete-encased electrode
    4. It must be bonded to the interior metal piping

    Explanation

    Section 250.53(D)(2) requires a metal underground water pipe electrode to be supplemented by at least one additional electrode selected from 250.52(A)(2) through (A)(8). The supplemental electrode protects the grounding system if the water pipe is later replaced with plastic.

  68. Question 68Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A service has 350 kcmil copper ungrounded conductors, and the grounding electrode conductor is run to a ground rod. What is the largest size grounding electrode conductor that 250.66(A) requires?

    1. 2 AWG
    2. 6 AWG Correct answer.
    3. 1/0 AWG
    4. 4 AWG

    Explanation

    Section 250.66(A) states that the grounding electrode conductor for a rod, pipe, or plate electrode is not required to be larger than 6 AWG copper. Table 250.66 would otherwise call for 2 AWG copper with 350 kcmil service conductors.

  69. Question 69Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    In a separately derived system, the system bonding jumper is installed at the first system disconnecting means instead of at the transformer. What must be run from the transformer to that disconnecting means?

    1. A second system bonding jumper to keep the path continuous
    2. A grounding electrode conductor sized per Table 250.66
    3. A supply-side bonding jumper, run with the grounded conductor Correct answer.
    4. An equipment grounding conductor sized per Table 250.122

    Explanation

    Section 250.30(A) permits a single system bonding jumper at either the source or the first system disconnecting means, but not both. Where it is located at the disconnecting means, a supply-side bonding jumper must be run from the source equipment to that point along with the grounded conductor.

  70. Question 70Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Three branch circuits protected at 20 A, 30 A, and 50 A share a single raceway with one equipment grounding conductor. What minimum size copper equipment grounding conductor is required?

    1. 10 AWG Correct answer.
    2. 8 AWG
    3. 6 AWG
    4. 12 AWG

    Explanation

    Where multiple circuits are installed in the same raceway, 250.122 requires the single equipment grounding conductor to be sized for the largest overcurrent device protecting any of the circuits. The largest device is 50 A, which Table 250.122 matches to 10 AWG copper.

  71. Question 71Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A building has a metal underground water pipe, a concrete-encased electrode, and a rod electrode available. What does 250.50 require?

    1. Any single electrode may be selected
    2. The rod electrode is optional if the water pipe is present
    3. All must be bonded into one system Correct answer.
    4. Only the water pipe electrode is used

    Explanation

    Section 250.50 requires all of the grounding electrodes described in 250.52(A)(1) through (A)(7) that are present at a building to be bonded together to form a single grounding electrode system. Selecting just one available electrode does not satisfy the rule.

  72. Question 72Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A 12 AWG copper conductor with 75°C insulation has a tabulated ampacity of 25 A and is proposed for a 22 A load. Which statement is correct?

    1. 20 A is the maximum, so 12 AWG is not permitted here Correct answer.
    2. A 25 A breaker is acceptable because it is a standard rating
    3. A 30 A breaker is acceptable because the ampacity is 25 A
    4. No overcurrent protection is needed for a 22 A load

    Explanation

    Section 240.4(D) limits 12 AWG copper to 20 A overcurrent protection, so the tabulated 25 A ampacity cannot be used to justify a larger breaker for this general branch circuit. Because the load exceeds the permitted protection level, a larger conductor must be installed.

  73. Question 73Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A service is supplied by two parallel 3/0 copper conductors per phase. What is the minimum size copper grounding electrode conductor under Table 250.66?

    1. 4 AWG
    2. 2 AWG Correct answer.
    3. 1/0 AWG
    4. 3/0 AWG

    Explanation

    For parallel service conductors, Table 250.66 is applied using the equivalent circular mil area of the largest ungrounded conductor, which here is 2 x 167,800 circular mils, or roughly 335,600 circular mils. That value falls in the over 3/0 through 350 kcmil row for copper, requiring a 2 AWG grounding electrode conductor.

  74. Question 74Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    Which of the following is a standard ampere rating for an inverse-time circuit breaker listed in NEC 240.6(A)?

    1. 130 A
    2. 550 A
    3. 275 A
    4. 175 A Correct answer.

    Explanation

    NEC 240.6(A) lists the standard ampere ratings recognized for fuses and inverse-time circuit breakers, and 175 A appears on that list. Ratings such as 130 A, 275 A, and 550 A fall between the listed values and are therefore not standard sizes.

  75. Question 75Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A service is supplied by 600 kcmil copper ungrounded conductors, and a concrete-encased electrode is the only grounding electrode used. What is the minimum size copper grounding electrode conductor permitted for the sole connection to that electrode?

    1. 2 AWG copper
    2. 4 AWG copper Correct answer.
    3. 1/0 copper
    4. 3/0 copper

    Explanation

    Table 250.66 would call for a 1/0 copper grounding electrode conductor for 600 kcmil copper service conductors, but 250.66(B) permits the conductor that is the sole connection to a concrete-encased electrode to be no larger than 4 AWG copper. The minimum required size therefore becomes 4 AWG copper.

  76. Question 76Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

    A 1200 A overcurrent device protects a feeder made up of four parallel sets of conductors, each set run in its own raceway. What does NEC 250.122 require for the equipment grounding conductors?

    1. A 6 AWG copper conductor in each of the four raceways
    2. A 3/0 copper conductor in only one of the four raceways
    3. A 1/0 copper conductor in each of the four raceways
    4. A 3/0 copper conductor in each of the four raceways Correct answer.

    Explanation

    Table 250.122 requires a 3/0 copper equipment grounding conductor for a circuit protected at 1200 A. Under 250.122(F)(1), where circuit conductors are run in parallel, each parallel raceway must contain a full-size equipment grounding conductor sized from that table.

  77. Question 77Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    In a one-family dwelling, at least how many 20-ampere small-appliance branch circuits are required to supply the kitchen, pantry, breakfast room, and dining room receptacle outlets?

    1. One
    2. Four
    3. Two Correct answer.
    4. Three

    Explanation

    Section 210.11(C)(1) requires two or more 20-ampere small-appliance branch circuits for the receptacle outlets in the kitchen, pantry, breakfast room, and dining room of a dwelling unit. A single circuit is never sufficient, and additional circuits beyond two are permitted but not required.

  78. Question 78Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    In a dwelling unit, general-purpose receptacle outlets along a wall must be placed so that no point along the floor line is more than what distance from a receptacle?

    1. 6 ft Correct answer.
    2. 10 ft
    3. 8 ft
    4. 4 ft

    Explanation

    Section 210.52(A)(1) requires receptacle outlets so that no point measured horizontally along the floor line of any wall space is more than 6 ft from a receptacle. This spacing rule keeps appliance cords within reach without extension cords.

  79. Question 79Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Service-drop conductors must be kept at least what minimum distance from windows designed to open, doors, porches, balconies, and similar locations?

    1. 1 ft
    2. 3 ft Correct answer.
    3. 6 ft
    4. 2 ft

    Explanation

    Section 230.9(A) requires open service conductors to maintain at least 3 ft of clearance from windows that are designed to open, doors, porches, balconies, ladders, stairs, fire escapes, and similar locations. The clearance protects occupants and prevents contact with energized conductors.

  80. Question 80Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    What is the smallest copper conductor permitted for service-drop conductors, regardless of the calculated load?

    1. 6 AWG
    2. 2 AWG
    3. 4 AWG
    4. 8 AWG Correct answer.

    Explanation

    Section 230.23(B) sets the absolute minimum size for service-drop conductors at 8 AWG copper or 6 AWG aluminum. The calculated load may require larger conductors, but it can never justify a size below this floor.

  81. Question 81Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Overhead branch-circuit conductors operating at 600 volts or less that pass over a residential driveway must maintain a minimum clearance of

    1. 12 ft Correct answer.
    2. 18 ft
    3. 10 ft
    4. 15 ft

    Explanation

    Section 225.18 requires 12 ft of clearance above residential driveways and commercial areas such as parking lots and driveways. The 10 ft value applies only to finished grade, sidewalks, and platforms not subject to truck traffic.

  82. Question 82Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    The service disconnecting means for a building must be installed in which location?

    1. Outside or inside nearest the point of entrance of the service conductors Correct answer.
    2. Only at the point farthest downstream on the load side
    3. Anywhere inside the building that is accessible to the owner
    4. Only on the utility company pole at the property line

    Explanation

    Section 230.70(A)(1) requires the service disconnecting means to be installed at a readily accessible location, either outside the building or inside nearest the point of entrance of the service conductors. Keeping it near the point of entry limits the length of unprotected service conductors inside the building.

  83. Question 83Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    In a dwelling unit, receptacle outlets in which of these areas require ground-fault circuit-interrupter protection?

    1. The bedroom
    2. The hallway
    3. The living room
    4. The bathroom Correct answer.

    Explanation

    Section 210.8(A) lists dwelling unit locations requiring GFCI protection, and bathrooms are included for all 125-volt, 15- and 20-ampere receptacles. Living rooms, bedrooms, and hallways are not among the GFCI-required dwelling locations.

  84. Question 84Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Service-drop conductors passing over a roof must maintain a minimum clearance above the roof surface of

    1. 6 ft
    2. 10 ft
    3. 3 ft
    4. 8 ft Correct answer.

    Explanation

    Section 230.24(A) sets the basic clearance over a roof at 8 ft above the roof surface. Limited reductions apply only under the specific conditions listed in the exceptions to that section.

  85. Question 85Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Dwelling unit kitchen countertop receptacle outlets must be installed so that no point along the wall line is more than what distance from a receptacle outlet?

    1. 36 in.
    2. 12 in.
    3. 24 in. Correct answer.
    4. 48 in.

    Explanation

    Under 210.52(C)(1), receptacle outlets serving countertop and work surfaces must be arranged so that no point along the wall line is more than 24 in. measured horizontally from a receptacle outlet. This replaces the older four-foot spacing approach.

  86. Question 86Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    The branch circuit that supplies bathroom receptacle outlets in a dwelling unit must have a minimum rating of

    1. 20 amperes Correct answer.
    2. 15 amperes
    3. 25 amperes
    4. 30 amperes

    Explanation

    Section 210.11(C)(3) requires at least one 20-ampere branch circuit to supply bathroom receptacle outlets, and that circuit is generally restricted to bathroom receptacles. A 15-ampere circuit does not satisfy the requirement.

  87. Question 87Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A feeder supplying a continuous load must have conductors with an ampacity of at least what percentage of the continuous load, plus 100 percent of the noncontinuous load?

    1. 100 percent
    2. 150 percent
    3. 125 percent Correct answer.
    4. 110 percent

    Explanation

    Section 215.2(A)(1)(a) requires feeder conductors to have an ampacity of not less than 125 percent of the continuous load plus 100 percent of the noncontinuous load, before application of adjustment or correction factors. The 125 percent factor accounts for the heat buildup of loads operating continuously.

  88. Question 88Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Informational notes in Articles 210 and 215 recommend that voltage drop on a feeder plus branch circuit not exceed what percentage of the supply voltage?

    1. 5 percent Correct answer.
    2. 4 percent
    3. 2 percent
    4. 3 percent

    Explanation

    The informational notes in 210.19(A) and 215.2(A)(1) recommend that total voltage drop on the feeder plus branch circuit not exceed 5 percent, with no more than 3 percent on the branch circuit alone. These are performance recommendations rather than mandatory rules.

  89. Question 89Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Where a feeder or branch circuit supplies a separate building or structure, the disconnecting means must be installed

    1. On the utility pole that serves the property
    2. At whatever point the building owner finds convenient
    3. Inside the basement of the building that contains the service
    4. At a readily accessible location nearest the point of entrance of the conductors Correct answer.

    Explanation

    Section 225.32 requires a disconnecting means at a readily accessible location, either outside or inside the building, nearest the point of entrance of the conductors. This limits the length of unprotected conductors within the structure.

  90. Question 90Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    For purposes of the 6-foot receptacle spacing rule in a dwelling unit, a wall space is counted when it is unbroken along the floor line and at least how wide?

    1. 4 ft
    2. 3 ft
    3. 1 ft
    4. 2 ft Correct answer.

    Explanation

    Section 210.52(A)(2)(1) states that wall space is measured along the floor line and includes any space 2 ft or more in width that is unbroken by doorways, fireplaces, and similar openings. Narrower segments are not counted.

  91. Question 91Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A 15-ampere branch circuit supplying receptacle outlets must use copper conductors of at least what size?

    1. 8 AWG
    2. 12 AWG
    3. 10 AWG
    4. 14 AWG Correct answer.

    Explanation

    Table 210.24 and 240.4(D) establish 14 AWG copper as the minimum conductor size protected by a 15-ampere overcurrent device. Larger conductors are permitted, but 14 AWG is the smallest allowed.

  92. Question 92Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    In a dwelling unit, 120-volt branch circuits supplying outlets in which of the following rooms require arc-fault circuit-interrupter protection?

    1. Bedrooms Correct answer.
    2. Garages
    3. Attics
    4. Bathrooms

    Explanation

    Section 210.12(A) lists dwelling areas requiring AFCI protection, and bedrooms are expressly included along with living rooms, dining rooms, hallways, closets, and similar rooms. Garages, bathrooms, and attics are not among the rooms listed for AFCI protection.

  93. Question 93Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Which of the following may be supplied by one of the two or more small-appliance branch circuits in a dwelling unit?

    1. Kitchen ceiling lighting fixtures
    2. A garage door opener
    3. A bathroom exhaust fan
    4. Receptacle outlets in the dining room Correct answer.

    Explanation

    Section 210.52(B)(2) permits the small-appliance branch circuits to supply only receptacle outlets in the kitchen, pantry, breakfast room, dining room, and similar areas. Lighting and other outlet types must be supplied by other circuits.

  94. Question 94Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    According to 210.52(G), how many receptacle outlets must be installed in an attached garage of a one-family dwelling?

    1. One for every 100 square feet of floor area
    2. At least two
    3. At least one Correct answer.
    4. None, unless a door opener is installed

    Explanation

    Section 210.52(G)(1) requires at least one receptacle outlet in each attached garage and in each detached garage with electric power. The requirement is a minimum, so additional outlets may be installed but are not mandated.

  95. Question 95Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A receptacle outlet serving the laundry area of a dwelling unit must be located within what maximum distance of the intended location of the laundry appliance?

    1. 10 ft
    2. 4 ft
    3. 3 ft
    4. 6 ft Correct answer.

    Explanation

    Section 210.50(C) requires at least one 125-volt, 15- or 20-ampere receptacle outlet in the laundry area, located within 6 ft of the intended location of the laundry appliance. The distance is measured to keep the appliance cord within reach.

  96. Question 96Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Each service disconnecting means must be permanently marked to indicate

    1. the voltage rating of the service transformer
    2. the interrupting rating of the upstream utility device
    3. that it is a service disconnecting means Correct answer.
    4. the name of the electrical contractor

    Explanation

    Section 230.70(B) requires each service disconnecting means to be permanently marked to identify it as a service disconnecting means. The marking lets firefighters and service personnel quickly locate the correct disconnect.

  97. Question 97Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    As a general rule, how many feeders or branch circuits may supply a separate building or other structure?

    1. Six
    2. Three
    3. One Correct answer.
    4. Two

    Explanation

    Section 225.30 permits a building or other structure to be supplied by only one feeder or branch circuit unless one of the specific conditions in 225.30(A) through (F) applies. The exceptions cover needs such as different voltages, emergency systems, and fire pumps.

  98. Question 98Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A building is permitted to be supplied by more than one service under which condition?

    1. The building exceeds 5,000 square feet
    2. Different service characteristics are required Correct answer.
    3. The utility company prefers that arrangement
    4. The owner requests it from the utility

    Explanation

    Section 230.2 permits more than one service only for the special conditions listed, such as different characteristics of service (voltage, frequency, or phase), different uses, or limited capacity. Owner preference, building size, and utility preference are not qualifying conditions.

  99. Question 99Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A feeder supplies a 40-ampere continuous load and a 30-ampere noncontinuous load. What minimum feeder conductor ampacity is required before any adjustment or correction factors are applied?

    1. 90 A
    2. 70 A
    3. 75 A
    4. 80 A Correct answer.

    Explanation

    Section 215.2(A)(1)(a) requires 125 percent of the continuous load plus 100 percent of the noncontinuous load, so 1.25 x 40 A + 30 A = 80 A. The feeder conductors must have an ampacity of at least 80 A before adjustments.

  100. Question 100Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A branch circuit supplies a 20-ampere continuous load and no other loads. What is the minimum standard rating of the branch-circuit overcurrent device?

    1. 30 A
    2. 20 A
    3. 25 A Correct answer.
    4. 35 A

    Explanation

    Section 210.20(A) requires the overcurrent device rating to be at least 125 percent of the continuous load plus 100 percent of the noncontinuous load, so 1.25 x 20 A = 25 A. Because 25 A is a standard rating in 240.6, no rounding up is needed.

  101. Question 101Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    A 20-ampere branch circuit supplies two or more receptacle outlets. The total rating of utilization equipment fastened in place, other than lighting fixtures, must not exceed what percentage of the branch-circuit rating?

    1. 80 percent
    2. 100 percent
    3. 125 percent
    4. 50 percent Correct answer.

    Explanation

    Section 210.23(A)(1) limits fastened-in-place utilization equipment, other than lighting fixtures, to 50 percent of the branch-circuit rating when the circuit supplies two or more outlets. The 80 percent limit applies to the total cord-and-plug-connected load on such a circuit.

  102. Question 102Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    Service-drop conductors crossing above a residential driveway must have a minimum vertical clearance above the ground of

    1. 18 ft
    2. 10 ft
    3. 15 ft
    4. 12 ft Correct answer.

    Explanation

    Table 230.24(A) sets 12 ft as the minimum vertical clearance for service-drop conductors over a residential driveway. Higher clearances are required over public streets, alleys, roads, and driveways other than residential driveways, while 10 ft applies over sidewalks and similar areas not subject to truck traffic.

  103. Question 103Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    For a one-family dwelling, outdoor receptacle outlets must be installed so that there is

    1. one outlet within 6.5 ft of every exterior door
    2. one outlet at the front only, accessible at grade level
    3. two outlets on every deck, balcony, or porch of 20 sq ft or more
    4. one at the front and one at the back, accessible at grade level Correct answer.

    Explanation

    Section 210.52(E)(1) requires at least one outdoor receptacle outlet accessible at grade level at the front of the dwelling and at least one at the back. The requirement is based on the front and back of the dwelling, not on the number of doors, decks, or porches.

  104. Question 104Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

    In a one-family dwelling, at least one receptacle outlet must be installed in a hallway that has a length of at least

    1. 10 ft Correct answer.
    2. 6 ft
    3. 8 ft
    4. 12 ft

    Explanation

    Section 210.52(H) requires at least one receptacle outlet in every hallway of a dwelling unit that is 10 ft or more in length. Hallways shorter than 10 ft are not required to have a receptacle outlet.

  105. Question 105Equipment for General Use (NEC Articles 400-460)

    Which of the following is a permitted use of flexible cord under Article 400?

    1. Replacing permanent wiring along the surface of a basement ceiling
    2. Carrying power to a hallway receptacle through a door opening
    3. Supporting a pendant luminaire over a dining table Correct answer.
    4. Wiring between a switch and a ceiling luminaire inside a wall cavity

    Explanation

    Article 400 permits flexible cord for pendants, for wiring luminaires, and for connecting appliances, but 400.12 prohibits using it as a substitute for the fixed wiring of a structure. Cords may not be run through holes in walls or ceilings, through doorways, or attached to building surfaces.

  106. Question 106Equipment for General Use (NEC Articles 400-460)

    Fixture wire is permitted to be used for which of the following?

    1. As a branch-circuit conductor run through conduit between two outlet boxes
    2. As a grounding electrode conductor
    3. As a feeder between a service panel and a subpanel
    4. Connecting a luminaire to branch-circuit conductors in an outlet box Correct answer.

    Explanation

    Section 402.10 permits fixture wire only for wiring inside luminaires and for connecting luminaires to the branch-circuit conductors. Section 402.11 forbids using fixture wire as branch-circuit conductors, so it cannot serve as a feeder or a grounding electrode conductor.

  107. Question 107Equipment for General Use (NEC Articles 400-460)

    In a dwelling unit, tamper-resistant receptacles are required for which of the following?

    1. A 15-ampere, 125-volt receptacle in a bedroom Correct answer.
    2. A 250-volt, 20-ampere receptacle for a window air conditioner
    3. A 50-ampere receptacle for an electric range
    4. A 30-ampere, 250-volt receptacle for an electric clothes dryer

    Explanation

    Section 406.12 requires tamper-resistant receptacles for 125-volt, 15- and 20-ampere receptacles in dwelling units, guest rooms, and child care facilities. Receptacles of other voltages or higher ampere ratings are outside that requirement.

  108. Question 108Equipment for General Use (NEC Articles 400-460)

    Each panelboard circuit must be identified as to its clear, evident, and specific purpose by means of ___

    1. a label on the panelboard enclosure hinge
    2. a circuit directory on or inside the panelboard door Correct answer.
    3. a tag attached to the branch-circuit conductor at the load end
    4. an entry in the electrical contractor's project file

    Explanation

    Section 408.4 requires a legible circuit directory with a clear, evident, and specific description of each circuit, located on the face or inside of the panelboard door. Descriptions such as "lights" or "misc." are not acceptable.

  109. Question 109Equipment for General Use (NEC Articles 400-460)

    The ampere rating of a general-use snap switch shall not be less than ___

    1. 125 percent of the branch-circuit ampacity
    2. the ampacity of the branch-circuit conductors
    3. the rating of the branch-circuit overcurrent device
    4. the load it controls Correct answer.

    Explanation

    Section 404.14 requires general-use switches to have a rating not less than the load to be controlled, with additional restrictions for specific load types such as tungsten-filament lamps. The switch rating is matched to the load, not to the circuit overcurrent device or conductor ampacity.

  110. Question 110Equipment for General Use (NEC Articles 400-460)

    A motor disconnecting means must be within sight of the motor. Under the NEC, "within sight" means visible and not more than ___

    1. 50 ft Correct answer.
    2. 25 ft
    3. 75 ft
    4. 100 ft

    Explanation

    The Article 100 definition of "within sight from" and "within sight of" means visible from the referenced equipment and not more than 15 m (50 ft) away. Section 430.102 applies this distance to the motor disconnecting means.

  111. Question 111Equipment for General Use (NEC Articles 400-460)

    A luminaire installed in a wet location must be ___

    1. supported by a chain independent of the outlet box
    2. listed and marked as suitable for wet locations Correct answer.
    3. enclosed in a listed junction box
    4. provided with a ground-fault circuit interrupter

    Explanation

    Article 410 requires luminaires installed in wet or damp locations to be listed and marked for the condition of use and to be installed so that water cannot enter or accumulate in the wiring or lampholders. GFCI protection and box enclosure are separate requirements.

  112. Question 112Equipment for General Use (NEC Articles 400-460)

    A 15-ampere, 125-volt receptacle is installed on an outdoor post in a wet location. The enclosure must ___

    1. remain weatherproof with the plug cap inserted or removed Correct answer.
    2. be listed as raintight only while a plug cap is inserted
    3. provide drainage weep holes at the bottom of a standard junction box
    4. be a nonmetallic box fitted with a gasketed blank plate

    Explanation

    Section 406.9(B) requires wet-location receptacles to be installed in an enclosure listed and identified as weatherproof that remains weatherproof whether or not a cord cap is inserted, and the enclosure must be raintight with the cap removed. Such receptacles also may not be installed in a face-up position.

  113. Question 113Equipment for General Use (NEC Articles 400-460)

    A panelboard with a rating of 200 amperes is equipped with a main circuit breaker. The overcurrent device protecting the panelboard must have a rating ___

    1. not greater than 200 amperes Correct answer.
    2. of at least 200 amperes but not more than 250 amperes
    3. not less than 125 percent of 200 amperes
    4. equal to the connected load but not less than 150 amperes

    Explanation

    Section 408.36 requires a panelboard to be protected by an overcurrent protective device having a rating not greater than that of the panelboard. The main breaker in the panelboard serves as that protection.

  114. Question 114Equipment for General Use (NEC Articles 400-460)

    A luminaire weighing 60 lb is installed on a standard octagonal outlet box. The luminaire must be ___

    1. supported independently of the outlet box Correct answer.
    2. supported by the box using at least two 8-32 machine screws
    3. attached to the box with a plaster ring
    4. supported by a listed ceiling fan box

    Explanation

    Section 410.36 requires luminaires weighing more than 23 kg (50 lb) to be supported independently of the outlet box by a means that attaches to the building structure. A 60-lb luminaire exceeds that threshold.

  115. Question 115Equipment for General Use (NEC Articles 400-460)

    A household range hood may be connected with a flexible cord and plug where ___

    1. the hood is protected by a GFCI breaker regardless of location
    2. the receptacle is on an individual branch circuit Correct answer.
    3. the cord is at least 6 ft long and is secured to the cabinet
    4. the receptacle is installed on the hood itself

    Explanation

    Section 422.16(B) permits cord-and-plug connection of range hoods where the hood is listed for it, the cord is 1 ft to 4 ft long and terminates in a grounding plug, the receptacle is supplied by an individual branch circuit, and the receptacle is accessible.

  116. Question 116Equipment for General Use (NEC Articles 400-460)

    For a permanently connected appliance rated more than 300 volt-amperes, the disconnecting means must be ___

    1. located within sight from the appliance Correct answer.
    2. installed within 25 ft of the appliance regardless of visibility
    3. equipped with a shunt trip operated from the appliance location
    4. replaced by a separate unfused disconnect on the appliance

    Explanation

    Section 422.31(B) requires the disconnecting means for a permanently connected appliance rated over 300 VA or over 1/8 hp to be within sight from the appliance, unless a unit switch marked with an "off" position is provided.

  117. Question 117Equipment for General Use (NEC Articles 400-460)

    A 4,800-watt, 240-volt fixed electric wall heater is the only load on a branch circuit. The minimum ampacity of the branch-circuit conductors is ___

    1. 30 A
    2. 25 A Correct answer.
    3. 24 A
    4. 20 A

    Explanation

    Section 424.3 treats fixed electric space-heating equipment as a continuous load, so the branch-circuit conductors must have an ampacity of at least 125 percent of the load. The load is 4,800 W divided by 240 V, or 20 A, and 125 percent of 20 A is 25 A.

  118. Question 118Equipment for General Use (NEC Articles 400-460)

    Branch-circuit conductors supplying a single motor must have an ampacity of at least ___

    1. 100 percent of the motor full-load current from Table 430.250
    2. 125 percent of the motor nameplate current
    3. 150 percent of the branch-circuit short-circuit protection rating
    4. 125 percent of the motor full-load current from the tables Correct answer.

    Explanation

    Section 430.22 requires branch-circuit conductors supplying a single motor to have an ampacity of not less than 125 percent of the motor full-load current. Motor full-load current is taken from the Article 430 tables rather than the nameplate.

  119. Question 119Equipment for General Use (NEC Articles 400-460)

    When sizing the branch-circuit conductors for a 25-hp, 460-volt, three-phase motor, the motor current used is ___

    1. the current from the motor manufacturer's data sheet
    2. the value in Table 430.250 Correct answer.
    3. the nameplate current divided by the service factor
    4. the current marked on the motor nameplate

    Explanation

    Section 430.6(A)(1) requires the current values from the Article 430 tables to be used to determine conductor ampacity and equipment ratings instead of the nameplate rating. For a 25-hp, 460-volt motor, Table 430.250 supplies that value.

  120. Question 120Equipment for General Use (NEC Articles 400-460)

    Branch-circuit conductors supplying a single hermetic motor-compressor must have an ampacity of not less than ___

    1. 125 percent of the rated-load current only
    2. 115 percent of the branch-circuit selection current or rated-load current, whichever is smaller
    3. 100 percent of the branch-circuit selection current
    4. 125 percent of the greater of the rated-load or selection current Correct answer.

    Explanation

    Section 440.32 requires conductors supplying a single motor-compressor to have an ampacity of not less than 125 percent of the motor-compressor rated-load current or the branch-circuit selection current, whichever is greater.

  121. Question 121Equipment for General Use (NEC Articles 400-460)

    The disconnecting means for an air-conditioning condensing unit must be ___

    1. within sight from and readily accessible from the unit Correct answer.
    2. located within 50 ft of the unit without regard to visibility
    3. installed on the line side of the unit's contactor
    4. at the serving panelboard, marked as the A/C disconnect

    Explanation

    Section 440.14 requires the disconnecting means for air-conditioning and refrigerating equipment to be located within sight from and readily accessible from the equipment. It may be mounted on or within the equipment itself.

  122. Question 122Equipment for General Use (NEC Articles 400-460)

    A dry-type transformer is installed in a supervised location. Its disconnecting means must be ___

    1. a lockable switch mounted on the transformer enclosure
    2. installed on the primary side only
    3. within sight from the transformer Correct answer.
    4. provided only where the transformer exceeds 50 kVA

    Explanation

    Section 450.14 requires a disconnecting means for a transformer that is located within sight from the transformer, with an additional restriction in unsupervised locations. There is no kVA threshold below which the disconnect is waived.

  123. Question 123Equipment for General Use (NEC Articles 400-460)

    The ampacity of the conductors supplying a capacitor must be not less than ___ of the capacitor rated current.

    1. 135 percent Correct answer.
    2. 150 percent
    3. 125 percent
    4. 100 percent

    Explanation

    Section 460.8(A) requires capacitor circuit conductors to have an ampacity of not less than 135 percent of the rated current of the capacitor. The elevated factor accounts for the voltage and current characteristics of capacitors.

  124. Question 124Equipment for General Use (NEC Articles 400-460)

    Where a dual-element time-delay fuse sized at 175 percent of motor full-load current will not carry the starting current, the fuse rating may be increased, but must not exceed ___ of motor full-load current.

    1. 250 percent
    2. 300 percent
    3. 200 percent
    4. 225 percent Correct answer.

    Explanation

    Table 430.52 permits a dual-element time-delay fuse at 175 percent of motor full-load current. Where that rating is not sufficient for starting, Exception No. 1 to 430.52(C)(1) permits the next higher standard rating, not exceeding 225 percent.

  125. Question 125Equipment for General Use (NEC Articles 400-460)

    A feeder supplies three motors with full-load currents of 30 A, 20 A, and 10 A. The minimum required feeder ampacity is ___

    1. 60 A
    2. 67.5 A Correct answer.
    3. 72.5 A
    4. 75 A

    Explanation

    Section 430.24 requires feeder conductors to have an ampacity of not less than 125 percent of the full-load current of the highest-rated motor plus 100 percent of the full-load currents of the other motors. Here that is 1.25 times 30 A, plus 20 A, plus 10 A, for 67.5 A.

  126. Question 126Equipment for General Use (NEC Articles 400-460)

    A 45-kVA, three-phase transformer with a 480-volt primary is protected by a primary-only overcurrent device. The maximum standard rating of that device is ___

    1. 100 A
    2. 70 A Correct answer.
    3. 80 A
    4. 60 A

    Explanation

    The primary current is 45,000 VA divided by (480 V times 1.732), or about 54.1 A. Table 450.3(B) permits primary-only protection at 125 percent of primary current, about 67.6 A, and where that value is not a standard rating the next higher standard rating is permitted. The next standard size above 67.6 A is 70 A.

  127. Question 127Equipment for General Use (NEC Articles 400-460)

    The conductors run from a generator's terminals to the first overcurrent device must have an ampacity of not less than ___ of the generator nameplate current rating.

    1. 125 percent
    2. 100 percent
    3. 115 percent Correct answer.
    4. 110 percent

    Explanation

    Section 445.13 requires the conductors from the generator terminals to the first distribution device containing overcurrent protection to have an ampacity of not less than 115 percent of the generator nameplate current rating.

  128. Question 128Equipment for General Use (NEC Articles 400-460)

    Where the branch-circuit short-circuit and ground-fault protective device for a hermetic motor-compressor, normally sized at 175 percent of rated-load current, will not permit the compressor to start, the device may be increased to a maximum of ___ of rated-load current.

    1. 300 percent
    2. 250 percent
    3. 225 percent Correct answer.
    4. 200 percent

    Explanation

    Section 440.22(A) permits the protective device rating to be increased above 175 percent of rated-load current when necessary for starting, but not to exceed 225 percent. The device must in any case be capable of carrying the starting current.

  129. Question 129Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Under Article 500, a Class I location is one in which which of the following is or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures?

    1. Easily ignitable fibers
    2. Combustible dust
    3. Corrosive liquid mist
    4. Flammable gas or vapor Correct answer.

    Explanation

    Article 500 sorts hazardous locations by the nature of the hazard. Class I covers flammable gases, vapors, and liquids; Class II covers combustible dusts; Class III covers easily ignitable fibers and flyings.

  130. Question 130Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    What is the minimum permitted distance from the inside wall of a permanently installed swimming pool to a receptacle outlet, absent a specific Code exception?

    1. 3 ft
    2. 5 ft
    3. 6 ft Correct answer.
    4. 4 ft

    Explanation

    Section 680.22(A)(1) keeps receptacles at least 6 ft from the inside walls of a permanently installed pool so that cords cannot reach the water.

  131. Question 131Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Receptacle outlets installed as part of a temporary wiring installation on a construction site must be provided with which of the following?

    1. An isolated ground
    2. A lockable disconnect
    3. A surge arrester
    4. GFCI protection Correct answer.

    Explanation

    Section 590.6(A) requires ground-fault circuit-interrupter protection for temporary 125-volt, single-phase, 15-, 20-, and 30-ampere receptacle outlets used on construction sites.

  132. Question 132Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Each commercial building and each commercial occupancy accessible to pedestrians must be provided with at least one outlet for sign or outline lighting supplied by a branch circuit rated not less than which value?

    1. 10 amperes
    2. 5 amperes
    3. 15 amperes
    4. 20 amperes Correct answer.

    Explanation

    Section 600.5(A) requires at least one sign or outline lighting outlet at each commercial building or occupancy accessible to pedestrians, and the branch circuit supplying it must be rated at least 20 amperes.

  133. Question 133Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    An area in which easily ignitable fibers or flyings are handled, manufactured, or used is classified under Article 500 as which type of location?

    1. Class IV
    2. Class II
    3. Class I
    4. Class III Correct answer.

    Explanation

    Class III locations are those made hazardous by easily ignitable fibers or flyings, such as textile mills and woodworking areas. Class I addresses gases and vapors, and Class II addresses combustible dust.

  134. Question 134Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    For branch-circuit and feeder sizing, the load of electric vehicle supply equipment is treated as which of the following?

    1. An intermittent load
    2. A continuous load Correct answer.
    3. A noncontinuous load
    4. A resistive load only

    Explanation

    Electric vehicle charging draws current for extended periods, so Article 625 treats it as a continuous load. Supply conductors and overcurrent devices must be sized at not less than 125 percent of the maximum load.

  135. Question 135Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    In an agricultural building where livestock are confined, an equipotential plane must be installed in confinement areas that have which feature?

    1. An open feed lot
    2. A slatted ceiling
    3. A wooden floor
    4. A conductive floor Correct answer.

    Explanation

    Section 547.10 requires equipotential planes in confinement areas that have a conductive floor, to limit voltage differences that can injure livestock. The plane is bonded to the electrical grounding system.

  136. Question 136Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Which statement describes a Class I, Division 2 location?

    1. Ignitable concentrations are present during normal operation
    2. Flammable liquids are transferred in open containers
    3. Ignitable concentrations are confined within closed systems Correct answer.
    4. Combustible dust clouds are present under normal conditions

    Explanation

    Section 500.5(B)(2) covers locations where flammable liquids or gases are handled in closed containers or systems from which they can escape only on accident or breakdown, or where positive-pressure ventilation prevents accumulation.

  137. Question 137Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    In the zone system of classification, a location where ignitable concentrations of flammable gas or vapor are present continuously or for long periods of time is designated as which of the following?

    1. Zone 0 Correct answer.
    2. Zone 1
    3. Zone 10
    4. Zone 2

    Explanation

    Article 505 defines Zone 0 as the location where ignitable concentrations are present continuously or for long periods. Zone 1 covers likely occurrence during normal operations, and Zone 2 covers unlikely, short-duration occurrence.

  138. Question 138Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Receptacles and fixed electrical equipment in patient care areas of a health care facility must be grounded by which method?

    1. A single equipment grounding conductor in any Chapter 3 raceway
    2. The grounded circuit conductor
    3. A redundant ground path with hospital-grade receptacles Correct answer.
    4. An isolated grounding electrode at each outlet

    Explanation

    Section 517.13 requires a redundant, low-impedance ground return path in patient care areas, such as a copper conductor in metal raceway or a copper conductor in a nonmetallic raceway, and receptacles must be listed as hospital grade.

  139. Question 139Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    A health care facility must be provided with a Type 1 essential electrical system where failure of the normal electrical supply would do which of the following?

    1. Require cancellation of elective procedures
    2. Raise energy use during peak hours
    3. Cause only minor inconvenience to staff
    4. Risk major injury or death to patients Correct answer.

    Explanation

    Article 517 establishes Type 1 and Type 2 essential electrical systems. Where loss of the normal source could cause major injury or death to patients or personnel, the more stringent Type 1 system is required.

  140. Question 140Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    A major repair garage is a building or portion of a building where which of the following activities is performed?

    1. Only washing and polishing of vehicles
    2. Only minor servicing such as lamp replacement
    3. Only storage of vehicles for sale
    4. Engine overhauls, painting, or body work Correct answer.

    Explanation

    Section 511.2 defines a major repair garage as a place where major repairs such as engine overhauls, painting, body and fender work, or repairs requiring fuel tank draining are performed. Those operations produce a greater hazard, so more area is classified.

  141. Question 141Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    A cord-and-plug-connected electric vehicle supply equipment operating at 250 volts, single phase, may have a maximum rating of which of the following?

    1. 80 or 100 amperes
    2. 30 or 50 amperes Correct answer.
    3. 60 or 80 amperes
    4. 40 or 60 amperes

    Explanation

    Section 625.44(A) permits cord-and-plug connection of EVSE at 125 volts, 15 or 20 amperes, or at 250 volts, 30 or 50 amperes. Larger units must be permanently connected.

  142. Question 142Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    The disconnecting means for an elevator must be capable of being which of the following?

    1. Removed from the machine room
    2. Locked in the closed position
    3. Operated only with a special tool
    4. Locked in the open position Correct answer.

    Explanation

    Section 620.51 requires the elevator disconnecting means to be capable of being locked in the open position so maintenance personnel can securely isolate power while working on the equipment.

  143. Question 143Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    The maximum current for a photovoltaic source circuit is calculated by multiplying the module short-circuit current by which factor?

    1. 1.56
    2. 1.15
    3. 1.00
    4. 1.25 Correct answer.

    Explanation

    Section 690.8(A) sets the maximum current of a PV source circuit at 125 percent of the short-circuit current, accounting for irradiance above standard test conditions. Conductor ampacity is then based on 125 percent of that value.

  144. Question 144Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Each recreational vehicle site in an RV park must be provided with a power supply that includes at least one receptacle rated which of the following?

    1. 20 amperes, 125 volts Correct answer.
    2. 30 amperes, 250 volts
    3. 50 amperes, 125 volts
    4. 15 amperes, 125 volts

    Explanation

    Section 551.71 requires each RV site to be supplied with at least one 20-ampere, 125-volt receptacle outlet. Larger 30-ampere and 50-ampere supplies are added for sites designed for larger vehicles.

  145. Question 145Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    An information technology equipment room covered by Article 645 is required to have which of the following?

    1. No disconnecting means other than the panelboard main
    2. A single marked disconnecting means for the equipment Correct answer.
    3. A separate service disconnecting means
    4. A shunt trip on each branch circuit

    Explanation

    Section 645.10 requires a means to disconnect power to all information technology equipment in the room, with the disconnecting means grouped and marked so emergency responders can shut the equipment down quickly.

  146. Question 146Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Where must the service equipment for a mobile home be located?

    1. On the mobile home itself
    2. At the utility service point
    3. Not more than 30 ft from the exterior wall Correct answer.
    4. Not more than 100 ft from the exterior wall

    Explanation

    Section 550.32(A) requires mobile home service equipment to be located in sight of the mobile home and not more than 30 ft from its exterior wall, so occupants can reach the disconnect quickly.

  147. Question 147Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    The rating or setting of overcurrent protection for an arc welder must not exceed which percentage of the rated primary current of the welder?

    1. 300 percent
    2. 200 percent Correct answer.
    3. 100 percent
    4. 150 percent

    Explanation

    Section 630.12(A) permits overcurrent protection for arc welders up to 200 percent of the welder's rated primary current, because the high inrush and intermittent duty would otherwise cause nuisance opening.

  148. Question 148Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Where a photovoltaic system is provided with rapid shutdown, conductors outside the array boundary must be limited to what maximum voltage within 30 seconds of shutdown initiation?

    1. 150 volts
    2. 80 volts
    3. 600 volts
    4. 30 volts Correct answer.

    Explanation

    Section 690.12(B)(2) requires that, outside the array boundary, controlled conductors be reduced to not more than 30 volts within 30 seconds of rapid shutdown initiation, protecting firefighters working on the roof.

  149. Question 149Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    The overcurrent protective device supplying a fire pump motor branch circuit must be selected so that it does which of the following?

    1. Carries locked-rotor current indefinitely Correct answer.
    2. Is a listed ground-fault circuit interrupter
    3. Is sized at 125 percent of full-load current
    4. Opens within 10 seconds at locked-rotor current

    Explanation

    Section 695.4(B) requires the fire pump overcurrent device to carry the locked-rotor current of the motor indefinitely. The fire pump must be able to start and run during a fire even if that means the protective device does not open on overload.

  150. Question 150Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    A conduit entering an enclosure that contains arcing or igniting equipment in a Class I, Division 1 location must have a sealing fitting installed at which location?

    1. At the boundary of the classified area
    2. Within 6 ft of the enclosure
    3. At the first junction box
    4. Within 18 in. of the enclosure Correct answer.

    Explanation

    Section 501.15(A) requires a seal within 18 in. of the enclosure so that gases cannot travel through the conduit and be ignited by arcs inside the enclosure. Seals at the boundary where conduit leaves the classified area are required in addition, not instead.

  151. Question 151Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    Metal parts within what horizontal distance of the inside walls of a permanently installed pool must be bonded to the equipotential bonding grid?

    1. 5 ft Correct answer.
    2. 3 ft
    3. 10 ft
    4. 8 ft

    Explanation

    Section 680.26 requires bonding of metal parts that are within 5 ft of the inside walls of the pool, along with the pool structure, deck reinforcement, and metal fittings, so that voltage gradients in and around the water are minimized.

  152. Question 152Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

    The switch or circuit breaker supplying a motor fuel dispensing device must do which of the following?

    1. Open only the ungrounded conductors
    2. Disconnect all conductors, including the neutral Correct answer.
    3. Be a listed GFCI device
    4. Be located only at the service equipment

    Explanation

    Section 514.11(A) requires the disconnect for a dispensing device to simultaneously open all conductors of the circuit, including the grounded conductor, so the dispenser is completely isolated during servicing.

  153. Question 153Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    Branch-circuit conductors supplying a single 10 hp, 460 V, three-phase motor must have an ampacity of at least what percentage of the motor full-load current?

    1. 100 percent
    2. 115 percent
    3. 150 percent
    4. 125 percent Correct answer.

    Explanation

    Section 430.22(A) requires branch-circuit conductors supplying a single motor to have an ampacity of not less than 125 percent of the motor full-load current rating. The extra 25 percent provides margin so the conductors are not loaded to their ampacity while carrying continuous motor current.

  154. Question 154Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A motor has a nameplate service factor of 1.15 and a nameplate full-load current of 18 A. The overload protective device is permitted to be rated at a maximum of what percentage of 18 A?

    1. 150 percent
    2. 100 percent
    3. 125 percent Correct answer.
    4. 115 percent

    Explanation

    Section 430.32(A)(1) permits overload protection set at not more than 125 percent of the motor nameplate current rating where the motor has a marked service factor of 1.15 or greater, or a marked temperature rise of 40 degrees C or less. The 1.15 service factor qualifies this motor for the 125 percent value.

  155. Question 155Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    Branch-circuit conductors supplying a single motor-compressor must have an ampacity of not less than 125 percent of which current value?

    1. the locked-rotor current
    2. the branch-circuit selection current only
    3. the greater of the two marked currents Correct answer.
    4. the rated-load current only

    Explanation

    Section 440.32 requires conductors to be sized at 125 percent of the larger of the motor-compressor rated-load current or the branch-circuit selection current. The branch-circuit selection current is used when the nameplate value exceeds the rated-load current, because it reflects the actual circuit requirement.

  156. Question 156Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    The disconnecting means for a motor must have an ampere rating of not less than what percentage of the motor full-load current?

    1. 100 percent
    2. 115 percent Correct answer.
    3. 150 percent
    4. 125 percent

    Explanation

    Section 430.110(A) requires the motor disconnecting means to have an ampere rating of at least 115 percent of the motor full-load current rating. This ensures the switch can carry the motor current continuously without overheating.

  157. Question 157Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    For a standard squirrel-cage motor, the maximum rating of an inverse-time circuit breaker used for branch-circuit short-circuit and ground-fault protection is what percentage of the motor full-load current?

    1. 175 percent
    2. 300 percent
    3. 250 percent Correct answer.
    4. 800 percent

    Explanation

    Table 430.52 sets the inverse-time circuit breaker limit at 250 percent of the motor full-load current for the usual motor types. The higher percentages in the table apply to other protective device types designed to ride through starting current.

  158. Question 158Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    When sizing the branch-circuit conductors and the short-circuit protective device for a motor branch circuit, which current value is used?

    1. the locked-rotor current marked on the nameplate
    2. 125 percent of the nameplate full-load current
    3. the full-load current from the tables in 430.250 Correct answer.
    4. the full-load current stamped on the motor nameplate

    Explanation

    Section 430.6(A)(1) requires the motor full-load current values from Table 430.250 to be used for sizing conductors and selecting short-circuit and ground-fault protective devices. Nameplate current is used only for the separate overload protection required by 430.32.

  159. Question 159Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A motor-compressor is marked with a rated-load current of 20 A and a branch-circuit selection current of 24 A. What is the largest standard rating of branch-circuit short-circuit and ground-fault protective device permitted before any increase for starting current?

    1. 50 A
    2. 40 A Correct answer.
    3. 35 A
    4. 45 A

    Explanation

    Section 440.22(A) limits the device to 175 percent of the larger of the rated-load current or the branch-circuit selection current. Here the larger value is 24 A, and 175 percent of 24 A is 42 A, so the largest standard device that does not exceed the limit is 40 A.

  160. Question 160Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    Where must the disconnecting means for a motor be located?

    1. within sight of and accessible from the motor Correct answer.
    2. at the panelboard that supplies the branch circuit
    3. anywhere within 50 ft of the motor
    4. at the service disconnecting means

    Explanation

    Section 430.102(B) requires a disconnecting means for the motor to be located within sight from and readily accessible from the motor location and the driven machinery. This lets a worker see the disconnect and the motor at the same time, and reach the disconnect quickly.

  161. Question 161Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A feeder supplies two motors: a 10 hp, 460 V motor with a Table 430.250 full-load current of 14 A and a 5 hp, 460 V motor with a full-load current of 7.6 A. What is the minimum feeder conductor ampacity?

    1. 21.6 A
    2. 25.1 A Correct answer.
    3. 27.0 A
    4. 35.0 A

    Explanation

    Section 430.24 requires 125 percent of the full-load current of the highest-rated motor plus the sum of the full-load currents of the other motors. Here that is 1.25 times 14 A plus 7.6 A, which equals 25.1 A.

  162. Question 162Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    For a standard motor, the maximum setting of an instantaneous-trip circuit breaker permitted for branch-circuit short-circuit and ground-fault protection is what percentage of full-load current?

    1. 300 percent
    2. 175 percent
    3. 250 percent
    4. 800 percent Correct answer.

    Explanation

    Table 430.52 permits an instantaneous-trip circuit breaker set at up to 800 percent of the motor full-load current. Instantaneous devices have no intentional time delay, so the much higher percentage is allowed to avoid tripping during motor starting.

  163. Question 163Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A branch circuit supplies several motors, each rated not more than 1 hp and each drawing not more than 6 A. What is the maximum rating of the branch-circuit short-circuit and ground-fault protective device permitted by 430.53(B)?

    1. 30 A
    2. 25 A
    3. 15 A
    4. 20 A Correct answer.

    Explanation

    Section 430.53(B) permits a branch circuit supplying two or more motors, each rated not more than 1 hp and each drawing not more than 6 A full-load current, to be protected at not more than 20 A. Each motor must still be provided with its own overload protection.

  164. Question 164Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A 15 hp, 460 V motor has a Table 430.250 full-load current of 21 A. Dual-element fuses at 175 percent do not carry the starting current. What is the largest standard fuse rating permitted?

    1. 45 A Correct answer.
    2. 60 A
    3. 40 A
    4. 50 A

    Explanation

    Section 430.52(C)(1) starts at 175 percent of 21 A, or 36.75 A, which permits a 40 A fuse. When that is not enough to start the motor, Exception No. 2 permits an increase, but the rating may not exceed 225 percent, and 225 percent of 21 A is 47.25 A, so 45 A is the largest standard size allowed.

  165. Question 165Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A feeder supplies two motor-compressors with rated-load currents of 20 A and 12 A. What is the minimum conductor ampacity required by Article 440?

    1. 32 A
    2. 37 A Correct answer.
    3. 45 A
    4. 40 A

    Explanation

    Section 440.33 requires 125 percent of the current of the largest motor-compressor plus the sum of the currents of the other compressors on the feeder. That is 1.25 times 20 A plus 12 A, or 37 A.

  166. Question 166Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    Where several motors are supplied by a single branch circuit under 430.53(C), how is the branch-circuit short-circuit and ground-fault protective device sized?

    1. 125 percent of the total full-load current of all the motors
    2. 125 percent of the full-load current of the largest motor on the circuit
    3. the largest motor's 430.52 rating plus the other motors' full-load currents Correct answer.
    4. the sum of the full-load currents of every motor on the branch circuit

    Explanation

    Section 430.53(C) sizes the protective device as it would be for the largest motor under 430.52, plus the sum of the full-load currents of the other motors. The resulting rating may not exceed the ampacity of the branch-circuit conductors.

  167. Question 167Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A packaged air-conditioning unit contains a hermetic refrigerant motor-compressor. Which rules govern the sizing of its branch circuit?

    1. Article 422, because the unit is an appliance
    2. Article 440 only, because Article 430 never applies to motor-compressors
    3. Article 440, which supplements or modifies Article 430 Correct answer.
    4. Article 430 only, because the compressor is a motor

    Explanation

    Section 440.3 states that the provisions of Article 440 supplement or modify those of Article 430, and where they differ Article 440 applies. Hermetic refrigerant motor-compressors therefore use the Article 440 sizing values such as rated-load current and branch-circuit selection current.

  168. Question 168Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

    A cord-and-plug-connected room air conditioner must be provided with which of the following?

    1. a fused attachment plug
    2. a GFCI receptacle
    3. an LCDI or an AFCI Correct answer.
    4. a standard grounding-type receptacle

    Explanation

    Section 440.65 requires cord-and-plug-connected room air conditioners to be provided with a leakage-current detector interrupter or an arc-fault circuit interrupter. These devices protect against the cord and plug faults that are common with this equipment.

  169. Question 169Special Systems and Communications Circuits (NEC Chapters 7-8)

    Under NEC Article 700, a storage battery used as the emergency power source for an emergency system must be able to supply the total emergency load for a minimum of how long?

    1. 30 minutes
    2. 1½ hours Correct answer.
    3. 4 hours
    4. 1 hour

    Explanation

    Article 700 requires an emergency storage battery to have the capacity to supply and maintain the total emergency load for at least 1½ hours while holding at least 87½ percent of system voltage. Durations shorter than that do not meet the minimum capacity requirement for an emergency system.

  170. Question 170Special Systems and Communications Circuits (NEC Chapters 7-8)

    Article 725 of the NEC applies to which of the following?

    1. Only circuits operating at more than 600 volts
    2. Circuits supervised by a listed fire alarm control unit
    3. Optical fiber cables installed in plenum spaces
    4. Class 1, 2, and 3 signaling and remote-control circuits Correct answer.

    Explanation

    Article 725 governs remote-control, signaling, and power-limited circuits that are not an integral part of equipment, which includes Class 1, Class 2, and Class 3 circuits. Fire alarm circuits are covered by Article 760 and optical fiber cables by Article 770.

  171. Question 171Special Systems and Communications Circuits (NEC Chapters 7-8)

    Which marking identifies an optical fiber cable that is listed for installation in a plenum?

    1. OFN
    2. OFNP Correct answer.
    3. OFNG
    4. OFNR

    Explanation

    Article 770 uses suffix letters to show where an optical fiber cable may be installed: OFNP is the nonconductive plenum-rated cable (OFCP is the conductive version). Plenum cables are tested for low smoke and flame spread for use in air-handling spaces.

  172. Question 172Special Systems and Communications Circuits (NEC Chapters 7-8)

    A homeowner installs a generator to back up the refrigerator and furnace during utility outages. Which NEC article covers this installation?

    1. Egress lighting installed because the building code requires it
    2. A homeowner's generator backing up selected loads Correct answer.
    3. A critical operations power system for a 911 call center
    4. A standby supply for a fire pump required by the local code

    Explanation

    Article 702 applies to optional standby systems, which are permanently installed to serve selected loads on a voluntary basis. Systems that serve mandatory life-safety or code-required loads fall under Articles 700, 701, or 708 instead.

  173. Question 173Special Systems and Communications Circuits (NEC Chapters 7-8)

    Which marking indicates a power-limited fire alarm cable that is listed for use in a vertical riser?

    1. FPLR Correct answer.
    2. FPL
    3. FPLP
    4. PLTC

    Explanation

    Article 760 uses the letter suffix to indicate where a fire alarm cable may be installed: FPLR for risers, FPLP for plenums, and FPL for other permitted locations. A vertical run between floors therefore calls for a riser-rated marking.

  174. Question 174Special Systems and Communications Circuits (NEC Chapters 7-8)

    What is the minimum size copper conductor permitted for grounding a communications primary protector?

    1. 16 AWG copper
    2. 22 AWG copper
    3. 14 AWG copper Correct answer.
    4. 18 AWG copper

    Explanation

    The grounding conductor for a communications primary protector must be copper and no smaller than 14 AWG, run as straight and as short as practicable to the grounding electrode. Smaller conductors do not provide the needed fault-current capacity.

  175. Question 175Special Systems and Communications Circuits (NEC Chapters 7-8)

    Where a coaxial cable from a community antenna television system enters a building, the outer conductive shield must be:

    1. bonded to any convenient equipment grounding conductor inside the building
    2. grounded only through equipment supplied by the cable provider
    3. bonded to the grounding electrode at the building entrance Correct answer.
    4. isolated from the building grounding electrode system to prevent ground loops

    Explanation

    Article 820 requires the outer conductive shield of the coaxial cable to be bonded to the building grounding electrode at the point of entry. This limits potential differences between the cable system and the building electrical system and gives surge current a path to ground.

  176. Question 176Special Systems and Communications Circuits (NEC Chapters 7-8)

    Class 2 thermostat cable must share an outlet box with 120-volt branch-circuit conductors. What does Article 725 require?

    1. Nothing additional, because CL2 cable insulation is rated for the branch-circuit voltage
    2. A barrier or other permanent separation from the power conductors Correct answer.
    3. That the Class 2 cable be replaced with a Class 1 wiring method in that box
    4. That the box be marked with a warning label identifying the mixed circuits

    Explanation

    Class 2 and Class 3 conductors generally may not occupy the same raceway, outlet box, or enclosure as power conductors unless a barrier or other permanent separation keeps the two systems apart. The cable's listing by itself does not permit mixing with power conductors.

  177. Question 177Special Systems and Communications Circuits (NEC Chapters 7-8)

    For a receiving antenna installation covered by Article 810, what must be provided where the lead-in conductors enter the building?

    1. A disconnecting means for all lead-in conductors
    2. A listed antenna discharge unit near the point of entry Correct answer.
    3. A ground-fault circuit interrupter ahead of the lead-in conductors
    4. A listed coaxial surge suppressor mounted at the antenna mast

    Explanation

    Article 810 requires a listed antenna discharge unit for each lead-in conductor, installed as near as practicable to the point of entry and away from combustible material. The discharge unit drains surge current from the antenna system to ground.

  178. Question 178Special Systems and Communications Circuits (NEC Chapters 7-8)

    A technician plans to supply a Class 2 control circuit from a general-purpose 24-volt transformer that is not listed as a Class 2 power supply. Is this acceptable?

    1. Yes; any transformer secondary of 30 volts or less is automatically Class 2.
    2. No; the circuit must be supplied from a listed Class 2 power source. Correct answer.
    3. Yes, if the transformer is protected by a 15-ampere branch-circuit breaker.
    4. Yes, provided the transformer is listed for industrial control equipment.

    Explanation

    Article 725 requires Class 2 circuits to be supplied from a listed Class 2 power source, such as a listed Class 2 transformer or power supply. A general-purpose transformer secondary is not Class 2 merely because its output is 24 volts.

  179. Question 179Special Systems and Communications Circuits (NEC Chapters 7-8)

    Emergency system overcurrent protective devices must be selectively coordinated with:

    1. the utility's overcurrent devices, where the utility permits it
    2. only the branch-circuit overcurrent devices protecting the emergency loads
    3. all supply-side overcurrent protective devices Correct answer.
    4. only the overcurrent devices located within the same panelboard

    Explanation

    Section 700.32 requires emergency system overcurrent protective devices to be selectively coordinated with all supply-side overcurrent protective devices. The goal is to keep a fault on one emergency circuit from tripping an upstream device and dropping other emergency loads.

  180. Question 180Special Systems and Communications Circuits (NEC Chapters 7-8)

    A composite cable contains both optical fibers and current-carrying copper conductors. How must this cable be installed?

    1. Under Article 770 only, since the optical fiber is the primary transmission medium
    2. Under Article 800 only, because the conductors carry communications signals
    3. Under Article 725 regardless of the circuits the copper conductors supply
    4. Under Article 770 and the article covering the copper conductors Correct answer.

    Explanation

    A composite optical fiber cable must satisfy Article 770 for the fibers and must also comply with the article governing its electrical conductors. Which article applies to the conductors depends on the circuit they supply, such as Article 725, 760, or 800.

  181. Question 181Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which state agency administers the Oklahoma Electrical Licensing Act and issues electrical licenses?

    1. The Construction Industries Board Correct answer.
    2. The Oklahoma Department of Labor
    3. The Office of the State Fire Marshal
    4. The Oklahoma Corporation Commission

    Explanation

    The Construction Industries Board administers the Electrical Licensing Act, issuing licenses, adopting administrative rules, and enforcing compliance. The other agencies listed regulate utilities, labor matters, or fire safety rather than electrician licensure.

  182. Question 182Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which body is established to advise on electrical licensing matters and to hear appeals from licensing decisions?

    1. The Electrical Safety Council
    2. The State Board of Electrical Contractors and Examiners
    3. The Electrical Examiners and Appeals Board Correct answer.
    4. The Building Trades Advisory Commission

    Explanation

    The Electrical Examiners and Appeals Board is the statutory body that advises the Construction Industries Board on electrical licensing and hears appeals from licensing decisions. Its title reflects both functions.

  183. Question 183Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which standard governs electrical installations under Oklahoma's electrical rules?

    1. NFPA 54, the National Fuel Gas Code
    2. NFPA 99, the Health Care Facilities Code
    3. NFPA 101, the Life Safety Code
    4. NFPA 70, the National Electrical Code Correct answer.

    Explanation

    Oklahoma's electrical rules adopt NFPA 70, the National Electrical Code, as the installation standard, subject to amendments adopted by rule. The other documents address egress and fire safety, fuel gas piping, and health care systems.

  184. Question 184Oklahoma Electrical Licensing Statutes and Administrative Rules

    What must an applicant generally do to obtain a journeyman electrician license in Oklahoma?

    1. Provide a letter of recommendation from any licensed electrician
    2. Work for five years without sitting for any examination
    3. Complete a safety course and pay the license fee
    4. Pass an examination and document the required experience Correct answer.

    Explanation

    A journeyman applicant must pass a qualifying examination and document the field experience required by statute and rule. A recommendation letter, a short course, or experience alone does not satisfy both requirements.

  185. Question 185Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which activity requires an Oklahoma electrical contractor license?

    1. Inspecting electrical work for a city
    2. Contracting to perform electrical work for the public Correct answer.
    3. Working as a registered apprentice under a journeyman's supervision
    4. Replacing a receptacle in your own home

    Explanation

    An electrical contractor license is required to contract with the public to perform electrical work for compensation. Individual workers hold apprentice, journeyman, or master licenses and work under the contractor.

  186. Question 186Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which license category is the entry level for a person learning the electrical trade in Oklahoma?

    1. Master electrician
    2. Electrical contractor
    3. Apprentice electrician Correct answer.
    4. Journeyman electrician

    Explanation

    The apprentice electrician is the entry-level category in which a person learns the trade under supervision while accumulating experience toward journeyman licensure. Journeyman and master are licensed working levels above apprentice.

  187. Question 187Oklahoma Electrical Licensing Statutes and Administrative Rules

    What must a person do to perform electrical work lawfully as an apprentice in Oklahoma?

    1. Register with the Construction Industries Board and work under supervision Correct answer.
    2. Complete eight thousand hours of field experience before applying for registration
    3. Obtain a master electrician license
    4. Pass the journeyman examination before starting work

    Explanation

    Apprentices must be registered with the Construction Industries Board and may perform electrical work only under required supervision. Registration also establishes the documented experience that counts toward journeyman licensure.

  188. Question 188Oklahoma Electrical Licensing Statutes and Administrative Rules

    An apprentice is on a jobsite where a licensed journeyman is present. Which statement is correct?

    1. The apprentice may sign off on completed electrical work
    2. The apprentice may work alone once the journeyman leaves the site
    3. The apprentice may supervise other apprentices
    4. The apprentice may work under the journeyman's supervision Correct answer.

    Explanation

    Apprentice work must be directed and overseen by a licensed journeyman or master electrician. When that supervision is absent, the apprentice may not continue performing regulated electrical work.

  189. Question 189Oklahoma Electrical Licensing Statutes and Administrative Rules

    What is required for a business entity to hold an Oklahoma electrical contractor license?

    1. Every officer of the business must hold a master electrician license
    2. A licensed master electrician must serve as the qualifying party Correct answer.
    3. The business must be incorporated in Oklahoma
    4. The business must employ at least ten journeyman electricians

    Explanation

    An electrical contractor license is held by a business and requires a designated licensed master electrician who is responsible for the electrical work and code compliance. The other conditions are not part of the licensing requirements.

  190. Question 190Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which requirement is generally placed on an Oklahoma electrical contractor as a condition of licensure?

    1. Posting a cash deposit with the state treasurer
    2. Publishing the license number in a newspaper
    3. Maintaining general liability insurance coverage Correct answer.
    4. Joining a statewide trade association

    Explanation

    Electrical contractors must show and maintain general liability insurance coverage as a condition of licensure, with proof submitted at application and renewal. Association membership and newspaper publication are not licensing conditions.

  191. Question 191Oklahoma Electrical Licensing Statutes and Administrative Rules

    What is the main purpose of continuing education for Oklahoma electricians?

    1. Keeping licensees current on code changes and safety Correct answer.
    2. Increasing the number of licensed contractors in the state
    3. Satisfying local permit requirements
    4. Replacing the licensing examination at renewal

    Explanation

    Continuing education exists to maintain and update a licensee's knowledge of code changes and safe installation practice as a condition of renewal. It neither replaces the examination nor affects the number of licensees.

  192. Question 192Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which statement about performing electrical work for pay without the required Oklahoma license is accurate?

    1. It is permitted if the customer signs a written waiver
    2. It is permitted when the contract price is under $1,000
    3. It is regulated only by the local building official
    4. It is unlawful and may lead to criminal penalties Correct answer.

    Explanation

    The Act makes it unlawful to perform regulated electrical work for compensation without the required license, and violations may be prosecuted and are subject to Board action. Neither a small contract price nor a customer waiver creates an exception.

  193. Question 193Oklahoma Electrical Licensing Statutes and Administrative Rules

    An electrician repeatedly installs equipment in violation of the adopted code and falsifies inspection records. What may the Board do?

    1. Issue a warning that is removed from the record after one year
    2. Nothing, because only local inspectors enforce the code
    3. Suspend or revoke the license after disciplinary proceedings Correct answer.
    4. Refer the matter to a trade association

    Explanation

    Code violations and falsified records are grounds for disciplinary action by the Board, which may include suspension or revocation of the license. Local enforcement is a separate track and does not displace Board authority.

  194. Question 194Oklahoma Electrical Licensing Statutes and Administrative Rules

    How may an electrician licensed in another state become licensed in Oklahoma without taking the Oklahoma examination?

    1. By working thirty days under an Oklahoma master electrician
    2. By reciprocity when the Board finds standards equivalent Correct answer.
    3. By paying an additional processing fee only
    4. By joining an Oklahoma electrical contractors association

    Explanation

    The Act permits licensure by reciprocity or endorsement when the Board determines that the other jurisdiction's licensing requirements are substantially equivalent to Oklahoma's.

  195. Question 195Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which statement best describes the scope of a master electrician license compared with a journeyman license?

    1. A master may qualify an electrical contractor and supervise work Correct answer.
    2. Only a journeyman may supervise apprentices on a jobsite
    3. A journeyman may contract electrical work directly with the public
    4. The licenses are identical in authority but differ in fee

    Explanation

    A master electrician may supervise electrical work and serve as the qualifying party for an electrical contractor. A journeyman performs electrical work and may oversee apprentices but cannot qualify a contractor.

  196. Question 196Oklahoma Electrical Licensing Statutes and Administrative Rules

    A licensee continues to work after the license expires and is not renewed. Which description of the status is correct?

    1. The license stays active while renewal paperwork is pending
    2. The license remains valid for a 90-day grace period
    3. The license converts automatically to journeyman status
    4. The person is unlicensed and must stop working until reinstated Correct answer.

    Explanation

    Once a license expires without renewal, the holder is no longer licensed and may not perform regulated electrical work until the license is renewed or reinstated. No automatic grace period accompanies expiration.

  197. Question 197Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which of the following actions falls within the Construction Industries Board's authority under the Electrical Licensing Act?

    1. Prosecuting criminal cases in district court
    2. Issuing building permits for every county in the state
    3. Setting retail electric rates for utilities
    4. Investigating complaints and inspecting electrical work Correct answer.

    Explanation

    The Board investigates complaints, inspects regulated electrical work, and may discipline licensees. It does not set utility rates, issue local building permits, or prosecute criminal cases.

  198. Question 198Oklahoma Electrical Licensing Statutes and Administrative Rules

    An electrical contractor's designated master electrician resigns. What must the contractor do to remain in compliance?

    1. Notify the Board and secure a replacement master electrician Correct answer.
    2. Convert the contractor license to a journeyman license
    3. Continue operating indefinitely without a qualifying party
    4. Suspend all work permanently and surrender the license

    Explanation

    A contractor license depends on a qualifying master electrician, so the contractor must notify the Board and obtain a replacement within the time allowed. Operating without a qualifying party violates the Act.

  199. Question 199Oklahoma Electrical Licensing Statutes and Administrative Rules

    Which person is most likely exempt from Oklahoma's electrical licensing requirements?

    1. An electric utility employee working on utility-owned facilities Correct answer.
    2. A technician wiring a new commercial building for a contractor
    3. An apprentice working without supervision
    4. A handyman repairing a service panel for a fee

    Explanation

    Employees of an electric utility performing work on utility-owned facilities in the ordinary course of employment fall outside the licensing scheme that governs contractors and electricians. Commercial wiring, paid repair work, and unsupervised apprentice work all require licensure.

  200. Question 200Oklahoma Electrical Licensing Statutes and Administrative Rules

    A licensee whose license is suspended by the Board wants to challenge the decision. What is the proper course?

    1. File a lawsuit in federal court without any prior proceeding
    2. Ignore the order and continue working until the Board objects
    3. Request a hearing and pursue the appeal rights provided by law Correct answer.
    4. Ask the local inspector to overrule the Board

    Explanation

    A licensee may request a hearing and exercise the appeal rights provided by law after a Board action. Until that process produces relief, the order stands and working in defiance of it invites further penalties.

OK Electrician flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Working space depth, 480 volts
For equipment operating at 151 to 600 volts to ground, NEC Table 110.26(A)(1) requires a working space depth of 3 ft for Condition 1, 3.5 ft for Condition 2, and 4 ft for Condition 3.
Meaning of listed equipment
Equipment is listed when it appears in a list published by an organization acceptable to the authority having jurisdiction that evaluates products and maintains periodic inspection of production of listed equipment.
Dedicated equipment space dimensions
NEC 110.26(E) requires a dedicated equipment space extending 30 in. from the front of electrical equipment, the width of the equipment, and 6 ft above it or to the structural ceiling.
Available fault current marking
NEC 110.24 requires service equipment in other than dwelling units to be field marked with the maximum available fault current and the date the fault current calculation was performed.
NM cable fastening intervals
Nonmetallic-sheathed cable must be secured within 12 in. of each box and at intervals not exceeding 4.5 ft, as required by NEC 334.30.
Box volume per 12 AWG
NEC Table 314.16(B) assigns 2.25 cubic inches of box volume per 12 AWG conductor, 2.0 for 14 AWG, 2.5 for 10 AWG, and 1.75 for 18 and 16 AWG.
Direct burial cover, UF cable
NEC Table 300.5 requires 24 in. of cover for direct-buried UF cable generally, reduced to 18 in. for 120 V, 20 A residential circuits and 12 in. where GFCI-protected.
Angle pull box sizing
NEC 314.28(A)(2) requires an angle-pull box dimension of at least six times the trade size of the largest raceway, plus the trade sizes of the other raceways in the same row.
Small conductor protection, 14 AWG
NEC 240.4(D) limits overcurrent protection for 14 AWG copper to 15 A, for 12 AWG to 20 A, and for 10 AWG to 30 A, apart from specific permitted exceptions.
Concrete-encased grounding electrode
A concrete-encased electrode is at least 20 ft of 1/2 in. or larger reinforcing steel, or 4 AWG bare copper, encased in at least 2 in. of concrete near the bottom of a footing.
Equipment grounding conductor, 200 A
NEC Table 250.122 requires a 6 AWG copper equipment grounding conductor for a circuit protected by a 200 A overcurrent device, while a 100 A device requires 8 AWG copper.
Ten-foot tap rule
NEC 240.21(B)(1) permits a tap up to 10 ft long if its ampacity is at least one-tenth the rating of the overcurrent device ahead of it, with no splices and a single termination.
Dwelling receptacle wall spacing
NEC 210.52(A)(1) requires dwelling receptacle outlets so that no point along the wall line is more than 6 ft from a receptacle, which limits outlets to 12 ft apart.
Two small appliance circuits
NEC 210.11(C)(1) requires at least two 20 A small-appliance branch circuits for dwelling kitchen, pantry and dining areas, supplying only receptacle outlets there.
Overhead service clearance, driveway
NEC 230.24 requires overhead service conductors to have at least 12 ft clearance above a residential driveway, 10 ft above a sidewalk, and 18 ft above a public road.
Dwelling service disconnect rating
NEC 230.79(C) requires the service disconnecting means for a one-family dwelling to have a rating of not less than 100 A, with a three-wire service.
Flexible cord prohibited uses
NEC 400.8 prohibits using flexible cord as a substitute for fixed wiring, running it through holes in walls or ceilings, or concealing it above suspended ceilings.
Water heater branch circuit
NEC 422.13 requires the branch circuit for a storage-type water heater rated 20 gallons or more to have an ampacity of at least 125 percent of the appliance nameplate rating.
Air-conditioning disconnect location
NEC 440.14 requires the disconnecting means for air-conditioning and refrigerating equipment to be located within sight of and not more than 50 ft from the equipment.
Hazardous location classes
NEC Article 500 designates Class I for flammable gases and vapors, Class II for combustible dust, and Class III for ignitable fibers or flyings, each divided into Division 1 and Division 2.
Pool perimeter equipotential bonding
NEC 680.26 requires equipotential bonding of conductive pool shell parts and of perimeter surfaces extending at least 3 ft horizontally from the inside walls of the pool.
Photovoltaic source circuit current
NEC 690.8(A) requires photovoltaic source-circuit current to be calculated at 125 percent of short-circuit current, and conductor ampacity to be at least 125 percent of that result.
PV rapid shutdown voltage
NEC 690.12 requires rapid shutdown to reduce conductors outside the photovoltaic array boundary to 30 volts or less within 30 seconds after shutdown is initiated.
Motor full-load current source
NEC 430.6(A)(1) requires motor full-load current for sizing conductors, feeders and protection to be taken from Tables 430.247 through 430.250, not from the motor nameplate.
Motor branch circuit 125 percent
NEC 430.22 requires branch-circuit conductors supplying a single motor to have an ampacity of at least 125 percent of the motor full-load current rating.
Motor overload, 1.15 service factor
NEC 430.32 requires overload protection set at 125 percent of nameplate current for motors marked with a 1.15 service factor or a 40 degrees C temperature rise.
Compressor protection, 175 percent
NEC 440.22(A) permits short-circuit protection for an air-conditioning compressor at up to 175 percent of rated-load current, increased to 225 percent if the unit will not start.
Communications cable separation
NEC 800.133(A)(1) requires communications cables to be separated by at least 2 in. from power conductors, Class 1 circuits and non-power-limited fire alarm conductors unless a barrier separates them.
Intersystem bonding termination
NEC 250.94 requires a terminal bar at the service to bond communications, community antenna television and other systems, providing a common point for intersystem bonding.
Class 2 circuit limits
NEC Article 725 defines Class 2 circuits as limited-energy circuits whose power does not exceed the values in Tables 725.121, permitting reduced wiring and separation requirements.
Oklahoma electrical licensing authority
Electrical licenses in Oklahoma are issued by the Construction Industries Board under the Oklahoma Electrical Licensing Act, located in Title 59 of the Oklahoma Statutes, Sections 1680 through 1697.
Oklahoma apprentice supervision
Oklahoma requires registered electrical apprentices to work under the supervision of a licensed journeyman or contractor, with apprentice registration filed with the Construction Industries Board.

OK Electrician study guide

General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

Article 100: the definitions carry points

Article 100 punishes candidates who read fast. Learn the near-pairs: a grounded conductor is the current-carrying neutral; a grounding conductor is the equipment grounding conductor that carries no current except during a fault. Bonding joins metal parts into a conductive path; grounding connects to earth. A receptacle is an outlet device; a switch is a device but not an outlet. Utilization equipment does mechanical, chemical, heating, or similar work - not information processing.

Article 110: rules that always apply

110.3(B) makes listing and labeling instructions enforceable. 110.12 requires workmanlike installation. 110.14 covers terminations: torque values, no shared terminals for grounded and grounding conductors, and the 75°C limitation where terminations are unmarked. 110.16 arc-flash labeling and 110.24 available-fault-current labeling at services appear often as one-line items. Article 110 also covers examination, mounting, and the integrity of electrical equipment.

The working-space trap

Table 110.26(A)(1) clear depth depends on voltage and on the condition of the space, not on equipment rating. Condition 3 (exposed live parts on both sides of the aisle) adds depth over Condition 1. Width is 30 in or the width of the equipment, whichever is greater; height is 6½ ft; dedicated equipment space extends 6 ft above the equipment and to its full width and depth.

Worked rule: a 480 V panel facing a blank wall is Condition 1 → 36 in. If another 480 V panel with exposed live parts faces it across the aisle, you are in Condition 3 → 48 in. Questions offering 36 in as a universal answer are testing exactly this.

Wiring Methods and Materials (NEC Chapter 3)

Chapter 3 is about containment and protection

Article 300 sets rules that ride on top of every wiring method: protection from physical damage where conductors sit within 1¼ in of framing (300.4, nailing plates), burial depths (300.5), a box or fitting at every splice, angle, or termination (300.15), all conductors of a circuit grouped in the same raceway or slot (300.20), and restrictions in ducts and plenums (300.22). Then each article adds limits - EMT (358), PVC (352), FMC (348), LFMC (350), RMC/IMC - plus rules for cable assemblies, boxes, and wireways.

Fill and box-count math

Chapter 9 Table 1 caps raceway fill at 53 percent for one conductor, 31 percent for two, and 40 percent for three or more; a nipple 24 in or shorter may use 60 percent. Box fill under 314.16(B): each circuit conductor counts one volume; all equipment grounding conductors count as one; each clamp, support fitting, and grounding screw counts one; each device yoke counts as two conductors based on the largest conductor present. Volume per conductor: 14 AWG = 2.0, 12 AWG = 2.25, 10 AWG = 2.50 cu in.

Worked example: a box with two 12 AWG two-wire cables with ground, one switch, internal clamps. Conductors 4 + EGC 1 + clamps 1 + yoke 2 = 8 counts × 2.25 = 18.0 cu in, so a 4 × 4 × 1¼ box (18 cu in) just passes while a 3 × 2 × 2½ box (12.5 cu in) fails.

Traps: PVC needs expansion fittings where temperature swings and is restricted where subject to physical damage; EMT is not permitted where severe corrosion or severe damage exists.

Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

240 and 250 are the highest-yield pair on this exam

Article 240 protects conductors. 240.4 keeps the OCPD from exceeding conductor ampacity; 240.4(D) caps small copper conductors at 15 A (14 AWG), 20 A (12 AWG), and 30 A (10 AWG) unless an article listed in 240.4(G) applies (motors, A/C equipment, fire pumps). 240.4(B) permits the next standard size up when ampacity falls between standard ratings, the device is 800 A or less, and the load does not exceed conductor ampacity. 240.6 lists standard ratings: 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100 …

Article 250: 250.24 covers service grounding and bonding; 250.50 requires all present electrodes to be bonded into one grounding electrode system; 250.52 defines electrodes (10 ft of metal water pipe in contact with earth, 8 ft rod, 20 ft of ½ in rebar or 4 AWG copper encased in concrete, 20 ft ground ring of 2 AWG); 250.53 requires a supplemental electrode for a water pipe and for a single rod unless 25 ohms or less is achieved. Use Table 250.66 for the grounding electrode conductor (sized from the largest service conductor) and Table 250.122 for the equipment grounding conductor (sized from the OCPD rating).

Worked rule: a 400 A service with 400 kcmil copper service conductors takes a 1/0 copper grounding electrode conductor (Table 250.66) but a 3 AWG copper equipment grounding conductor (Table 250.122). Swapping those tables is the classic error. Under 250.122(B), an EGC must be increased proportionally when circuit conductors are upsized for voltage drop.

Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

Branch circuits, feeders, and services

Article 210 governs branch circuits. In dwellings, 210.11(C) requires at least two 20 A small-appliance circuits, a 20 A laundry circuit, and a 20 A bathroom circuit. 210.52(A) requires receptacle spacing so that no point along the floor line of any qualifying wall space is more than 6 ft from a receptacle, and any wall space 2 ft or wider counts; kitchen countertops and islands have their own spacing requirements in the edition adopted. 210.8 lists GFCI locations and 210.12 the AFCI-protected areas - both have expanded each cycle, so read the adopted text instead of trusting memory. Article 220 supplies calculation methods, including the optional method for dwellings.

Article 215 sets feeder minimum size at the calculated load with the continuous/noncontinuous adjustments of 215.2. Article 225 covers outside branch circuits and feeders, including clearances and disconnects at separate structures.

Article 230 covers services: 230.24 overhead clearances (10 ft above sidewalks, 12 ft above driveways, 18 ft above public streets, 8 ft above roofs subject to foot traffic), 230.70 service disconnect at the nearest point of entry and never in a bathroom, 230.72 grouping, and 230.79 minimum ratings (100 A for a one-family dwelling, 60 A for others).

Worked example: a 12 ft wall section between two doorways is wall space, so at least one receptacle is required and the 6 ft/12 ft rule applies across the opening.

Trap: GFCI requirements attach to the receptacle and its location and rating, not to which circuit breaker feeds it.

Equipment for General Use (NEC Articles 400-460)

Articles 400 through 460: equipment for general use

Article 400 restricts flexible cords: they may not substitute for the fixed wiring of a structure, may not run through holes in walls, ceilings, or floors, and may not be attached to building surfaces (400.12). Article 406 covers receptacles, including replacement rules (406.4) and tamper-resistant requirements. Article 408 governs panelboards: 408.36 requires each panelboard to be protected at not more than its rating, and a back-fed main needs a field-installed hold-down. Article 410 covers luminaires, including closet clearances (410.16).

Article 422 applies to appliances: disconnecting means, cord-and-plug connections, and overcurrent protection per the nameplate. Article 424 covers fixed electric space heating: branch circuits are sized at 125 percent of the load because heaters are continuous, with a disconnect for each unit and for the thermostat where required. Article 450 covers transformers, with 450.3 setting the OCPD at 125 percent of primary current for transformers with primary-only protection (next standard size up allowed for primaries 9 A and above).

Worked example: a 45 kVA, 480 V three-phase to 208/120 V transformer. Primary current = 45,000 ÷ (480 × 1.732) = 54.1 A; 125 percent = 67.7 A, so the next standard size is a 70 A primary breaker.

Traps: using flexible cord as permanent wiring, forgetting the 125 percent factor for heaters and water heaters, and confusing transformer primary-protection percentages with secondary-protection percentages.

Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

Chapters 5 and 6: special occupancies, conditions, and equipment

Chapter 5 addresses places. Hazardous (classified) locations (Articles 500–506) turn on class, division or zone, and group - questions ask which wiring method or enclosure marking is permitted, so learn the class/division logic before memorizing details. Other high-yield articles: 511 commercial garages, 514 motor fuel dispensing, 517 health care facilities, 547 agricultural buildings, 555 marinas, 590 temporary installations, and 680 swimming pools, fountains, and similar installations.

Chapter 6 addresses equipment. Know these: 620 elevators, 625 electric vehicle supply equipment, 680 pools (680.26 equipotential bonding of pool shells, metal parts, and the 3 ft perimeter surface using 8 AWG solid copper), 690 solar photovoltaic systems, 695 fire pumps, 700 emergency systems, 701 legally required standby, 702 optional standby, and 705 interconnected power production sources.

Worked example (PV): a string with a short-circuit current of 10 A requires overcurrent devices rated at least 125 percent of that current per 690.8, and conductor ampacity at 125 percent of the result, so the design uses 12.5 A for the device and 15.6 A for conductor ampacity.

Traps: pool bonding is not the same as grounding - the equipotential grid serves a different purpose; 700.10 requires emergency circuits to be kept separate from normal wiring and protected from fire; special-occupancy articles override the general Chapter 3 method for the same installation.

Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

Articles 430 and 440 reward careful table work

Motor branch circuits are built from Table 430.250 full-load currents, not from the motor nameplate amperes. 430.22 sizes branch-circuit conductors at 125 percent of FLC. 430.52 caps the branch short-circuit and ground-fault protective device at 175 percent of FLC for a dual-element fuse and 250 percent for an inverse-time breaker, with the next standard size up permitted if the device will not carry starting current. Overload protection is separate: 430.32 sets it at 125 percent of the nameplate full-load amperes. A disconnecting means must be within sight - visible and not more than 50 ft away - per 430.102, and 430.24 sizes a circuit serving several motors by adding 125 percent of the largest FLC to the sum of the others.

Article 440 changes the inputs for hermetic refrigerant motor-compressors: use the rated-load current and branch-circuit selection current from the nameplate. 440.22 sets protection at 175 percent of rated-load current (225 percent where starting current trips the device), and 440.32 sizes branch conductors at 125 percent of the largest compressor rated-load current plus other loads.

Worked example: a 30 hp, 480 V, three-phase motor. Table 430.250 gives 40 A FLC. Conductors = 125 percent = 50 A, so 8 AWG copper at 75°C. Dual-element fuse maximum = 175 percent of 40 A = 70 A. Overload protection = 125 percent of the nameplate amperes.

Traps: using nameplate current where the table governs (motors) or the table where the nameplate governs (A/C compressors), and confusing overload protection with short-circuit and ground-fault protection.

Special Systems and Communications Circuits (NEC Chapters 7-8)

Chapters 7 and 8: special systems and communications

The dividing line is simple: Chapter 7 covers emergency, standby, fire alarm, Class 1/2/3, optical fiber, and signaling systems - mostly power-limited or life-safety circuits. Chapter 8 covers communications circuits, radio and TV antennas, and network-powered broadband under their own articles, generally not subject to Chapters 1–7 except where specifically referenced.

Key rules: Article 725 separates Class 2 and Class 3 circuits from power and Class 1 conductors - 725.136 permits them in the same enclosure only with a barrier or where the power conductors are introduced solely to connect to the equipment. Class 2 cables must be installed as their listing permits and cannot be reclassified above their listing. Article 760 covers fire alarm systems, distinguishing power-limited from non-power-limited circuits and requiring fire-resistant cable where circuit survivability is needed. Articles 800, 820, and 830 cover communications circuits and require a listed primary protector and a bonding conductor to the grounding electrode system at the point of entry.

Plenum rule of thumb: any cable installed in a plenum must be listed for plenum use (CMP for communications cable); a cable run inside a raceway that is entirely within the plenum is generally acceptable without a plenum rating, so questions often hinge on whether the raceway is complete and enclosed.

Traps: mixing Class 2 conductors with Class 1 or power conductors, using emergency-system wiring methods for optional standby loads, and forgetting that accessible abandoned cable not identified for future use must be removed.

Oklahoma Electrical Licensing Statutes and Administrative Rules

Oklahoma Electrical Licensing Act and Board rules

Oklahoma regulates electrical work through the Electrical Licensing Act (59 O.S. § 1680 et seq.), administered by the Construction Industries Board. The Board adopts the edition of NFPA 70 (NEC) in force for the state, adopts administrative rules governing electrical work, and through its electrical division handles licensing, renewals, and enforcement. Local authorities administer permits and inspections and may have local amendments, so installation questions always resolve back to the authority having jurisdiction.

Know the license structure: an electrical contractor license held by the business (requiring a designated qualified licensee plus proof of insurance and bonding), journeyman credentials obtained by examination, and apprentice registration. Work done under a permit is inspected by the AHJ, but the contractor remains responsible for code compliance regardless of who inspects.

How to answer statute questions

Statutes test who may perform electrical work, what license is required, when a permit is required, and the penalties for unlicensed work. Rules test renewal cycles, continuing education required before renewal, and supervision of apprentices by licensed journeymen. Oklahoma amends these provisions periodically, so confirm the current renewal period, CE hours, fees, and adopted code edition with the Board before relying on a specific number.

Rule of thumb: licensing, permits, and discipline are governed by statute and Board rule; installation methods are governed by the adopted NEC. When an item blends the two, answer with the code for how to install it and the statute for who may install it.

OK Electrician cheat sheet

Quick reference

General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

  • Article 100: "Listed" means equipment included in a list published by an organization acceptable to the AHJ that maintains periodic inspection of production and whose listing states the equipment meets a recognized standard or has been tested and found suitable.

  • Table 110.26(A)(1) working-space depth, 0-150 V to ground: 3 ft for Conditions 1, 2 and 3; for 151-600 V to ground: 3 ft (Condition 1), 3.5 ft (Condition 2), 4 ft (Condition 3).

  • 110.26(A)(2) width of working space: not less than 30 in., or the width of the equipment, whichever is greater; 110.26(A)(3) height: 6.5 ft from grade, floor or platform.

  • 110.26(E) dedicated equipment space: 30 in. deep from the front face, the width of the equipment, and 6 ft above the equipment or to the structural ceiling, whichever is lower.

  • 110.26(C)(2): equipment rated 1200 A or more and over 6 ft wide requires one entrance at each end of the working space.

  • 110.24(A): service equipment in other than dwelling units must be field-marked with the maximum available fault current and the date the calculation was performed.

  • 110.14(D): conductor terminations must be tightened to the torque value marked on the equipment or given in the manufacturer's instructions.

  • 110.3(B): listed or labeled equipment must be installed and used in accordance with any instructions included in the listing or labeling.

  • 110.12: electrical equipment must be installed in a neat and workmanlike manner; unused openings in enclosures must be effectively closed.

Quick reference

Wiring Methods and Materials (NEC Chapter 3)

  • 300.4(A)(1): bored holes in wood members must be at least 1 1/4 in. from the nearest edge, or the cable must be protected by a steel nail plate at least 1/16 in. thick.

  • Table 300.5 minimum cover for direct-buried cables: 24 in. general; 18 in. for 120 V, 20 A residential circuits; 12 in. for 120 V, 20 A residential circuits with GFCI protection.

  • 334.30: nonmetallic-sheathed cable secured within 12 in. of each box and at intervals not exceeding 4.5 ft.

  • Table 352.30: Schedule 40 PVC conduit supported at 3 ft intervals for 1/2 in. through 1 in., and 5 ft for 1 1/4 in. through 2 in.

  • 358.30: EMT secured within 3 ft of each box and at intervals not exceeding 10 ft.

  • Table 314.16(B) box fill allowance per conductor: 18 and 16 AWG = 1.75 cu. in.; 14 AWG = 2.0; 12 AWG = 2.25; 10 AWG = 2.5.

  • 314.28(A): straight-pull box dimension at least 8 times the trade size of the largest raceway; angle pulls at least 6 times the largest raceway plus the other raceways in the same row.

  • 310.15(B)(3)(a) adjustment for more than three current-carrying conductors in a raceway: 4-6 = 80%, 7-9 = 70%, 10-20 = 50%.

  • 300.22: only Types MC, AC, MI, or flexible metal conduit may be installed in ducts or plenums used for environmental air.

Quick reference

Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

  • 240.4(D) small-conductor overcurrent limits: 18 AWG = 7 A, 16 AWG = 10 A, 14 AWG = 15 A, 12 AWG = 20 A, 10 AWG = 30 A.

  • 240.6(A) standard ampere ratings include 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 400, 500, 600, 800, 1000, 1200 A.

  • 240.21(B)(1) 10-ft tap rule: tap conductor ampacity at least one-tenth the rating of the overcurrent device ahead of it, no splices, terminated in a single circuit breaker or fuse.

  • 250.52(A) grounding electrodes: metal water pipe with at least 10 ft in direct earth contact; rod or pipe at least 8 ft long; ground ring of at least 20 ft of bare 2 AWG copper; concrete-encased electrode of 20 ft of 1/2 in. rebar or 4 AWG copper.

  • 250.53: rod, pipe and plate electrodes must be at least 6 ft apart; a single rod must be supplemented by an additional electrode unless it has a resistance of 25 ohms or less.

  • 250.66: the grounding electrode conductor to a rod, pipe or plate electrode is not required to be larger than 6 AWG copper; for service conductors over 1100 kcmil copper the maximum required is 3/0 copper.

  • Table 250.122 copper equipment grounding conductors: 20 A circuit = 12 AWG, 100 A = 8 AWG, 200 A = 6 AWG, 400 A = 3 AWG.

  • 250.122(B): where ungrounded conductors are increased in size, the equipment grounding conductor must be increased proportionally.

  • 250.24(A)(1): the grounded service conductor is connected to the grounding electrode conductor at the service; 250.24(A)(5) prohibits regrounding it on the load side of the service disconnect.

Quick reference

Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

  • 210.52(A)(1): in dwelling units, receptacle outlets along walls must be installed so no point on the wall line is more than 6 ft from a receptacle, which limits spacing to 12 ft maximum.

  • 210.52(C)(1): dwelling kitchen countertops require at least one receptacle, with no point along the counter wall line more than 24 in. from a receptacle.

  • 210.8(A): GFCI protection is required for 125 V, 15 and 20 A receptacles in dwelling bathrooms, garages, outdoors, kitchens, laundry areas, unfinished basements, crawl spaces, and within 6 ft of sinks.

  • 210.12(A): arc-fault circuit-interrupter protection is required for 120 V, 15 and 20 A branch circuits supplying dwelling unit living areas, bedrooms, halls, closets and similar rooms.

  • 210.11(C): at least two 20 A small-appliance branch circuits, one 20 A laundry branch circuit, and one 20 A bathroom branch circuit are required in dwelling units.

  • 230.79(C): the service disconnecting means for a one-family dwelling must have a rating of not less than 100 A, three-wire.

  • 230.24(B) overhead service conductor clearances: 10 ft above sidewalks and grade, 12 ft above residential driveways, 18 ft above public roads and other areas subject to truck traffic.

  • 210.63: a 125 V receptacle outlet must be provided within 25 ft of heating, air-conditioning and refrigeration equipment for servicing.

  • 210.19(A) Informational Note: branch-circuit voltage drop should not exceed 3 percent, with a total of 5 percent for feeder plus branch circuit.

Quick reference

Equipment for General Use (NEC Articles 400-460)

  • 400.8: flexible cord may not be used as a substitute for fixed wiring, run through holes in walls or ceilings, concealed behind building surfaces, or installed above suspended ceilings.

  • 404.8(A): switches and circuit breakers used as switches must be located not more than 6 ft 7 in. above the floor or working platform.

  • 406.12: tamper-resistant receptacles are required in dwelling units; 406.9 requires weather-resistant receptacles in wet and damp locations.

  • 410.16: luminaires in clothes closets must maintain at least 12 in. clearance from the nearest point of the storage shelf.

  • 422.13: the branch circuit for a storage-type water heater rated 20 gallons or more must be rated at least 125 percent of the appliance's nameplate rating.

  • 424.3(B): branch-circuit conductors and overcurrent devices for fixed electric space-heating equipment must be sized at 125 percent of the nameplate rating.

  • 440.14: the disconnecting means for air-conditioning and refrigerating equipment must be within sight of and not more than 50 ft from the equipment.

  • Table 450.3(B): for transformers rated 1000 V or less, the primary overcurrent device is set at 125 percent of primary current when the secondary is protected at 125 percent, and may be increased up to 300 percent for primary-only protection.

Quick reference

Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

  • Article 500: Class I = flammable gases or vapors; Class II = combustible dust; Class III = ignitable fibers or flyings; each class is divided into Division 1 (normal) and Division 2 (abnormal) conditions.

  • 511.3: in commercial garages, the area up to 18 in. above the floor is a Class I, Division 2 location, along with areas near fuel-dispensing or repair points.

  • 517.13: health care facility patient care areas require a redundant ground path, typically an insulated copper equipment grounding conductor installed in metallic raceways.

  • 680.22(A)(1): receptacles supplying a permanently installed swimming pool must be not less than 6 ft from the pool edge, and all receptacles between 6 ft and 20 ft require GFCI protection.

  • 680.26(B): equipotential bonding is required for conductive pool shells and for perimeter surfaces extending at least 3 ft horizontally from the inside wall of the pool.

  • 690.8(A): photovoltaic source-circuit current is calculated as 125 percent of the short-circuit current, and conductor ampacity must be at least 125 percent of that value.

  • 690.12: rapid shutdown must reduce conductors outside the array boundary to 30 V or less within 30 seconds after shutdown is initiated.

  • Article 700 covers emergency systems, Article 701 legally required standby systems, and Article 702 optional standby systems, each with different capacity and testing requirements.

  • 590.6: all 125 V, 15 and 20 A receptacle outlets used during construction must have ground-fault circuit-interrupter protection.

Quick reference

Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

  • 430.6(A)(1): motor full-load current for sizing conductors, feeders and protection is taken from Tables 430.247 through 430.250, not from the motor nameplate.

  • 430.22: branch-circuit conductors supplying a single motor must have an ampacity of at least 125 percent of the motor full-load current rating.

  • Table 430.52: branch-circuit short-circuit protection may be 175 percent of motor FLC for an inverse-time breaker, 175 percent for a dual-element fuse, and 300 percent for a non-time-delay fuse.

  • 430.32: overload protection is set at 125 percent of nameplate current for motors with a 1.15 service factor or 40 degrees C rise, and 115 percent for all other motors.

  • 430.24: feeder conductors supplying several motors must have an ampacity of at least 125 percent of the largest motor FLC plus 100 percent of all other motor loads.

  • 430.102(B): a motor disconnecting means must be located within sight of the motor and of the driven machinery.

  • 440.22(A): short-circuit protection for an air-conditioning compressor may not exceed 175 percent of rated-load current, increased to 225 percent if the unit will not start.

  • 440.32: branch-circuit conductors supplying a single hermetic refrigerant motor-compressor must have an ampacity of at least 125 percent of the rated-load current.

Quick reference

Special Systems and Communications Circuits (NEC Chapters 7-8)

  • Article 725 divides remote-control and signal circuits into Class 1, Class 2 and Class 3; Class 2 and 3 circuits are limited-energy circuits governed by the power limits in Tables 725.121.

  • 725.136: Class 2 and Class 3 conductors must be separated from Class 1 and power conductors by at least 1/4 in., a barrier, or a listed raceway or cable assembly.

  • Article 760 distinguishes power-limited fire alarm (PLFA) circuits from non-power-limited fire alarm (NPLFA) circuits, which follow Article 300 wiring methods.

  • 800.133(A)(1): communications cables must be separated by at least 2 in. from power conductors, Class 1 circuits, and NPLFA conductors unless a permanent barrier separates them.

  • 250.94: an intersystem bonding termination must be provided at the service to bond communications, antenna, and other system grounding conductors.

  • 800.100: communications circuits entering a building must have a listed primary protector installed as near as practicable to the point of entry.

  • Article 770 covers optical fiber cables and requires separation from power conductors similar to communications cable rules.

  • Article 810: outdoor radio and television antennas must be bonded to the building grounding electrode system, and masts must maintain the required clearances from power conductors.

Quick reference

Oklahoma Electrical Licensing Statutes and Administrative Rules

  • Electrical licensing in Oklahoma is administered by the Construction Industries Board under the Oklahoma Electrical Licensing Act, Title 59 of the Oklahoma Statutes, Sections 1680 through 1697.

  • Rules implementing the Act are published in the Oklahoma Administrative Code under Title 158, the Construction Industries Board rules.

  • Electrical contracting requires a licensed electrical contractor; electrical work must be performed by licensed journeymen or by registered apprentices under supervision.

  • Apprentices must be registered with the Board and may perform electrical work only while under the supervision of a licensed journeyman or contractor.

  • Journeyman and contractor applicants must pass the Board-approved licensing examination and meet the required experience or training qualifications.

  • Licenses are renewed on a recurring cycle established by Board rule, subject to continuing education and fee requirements.

  • Local authorities having jurisdiction issue permits and perform inspections; the state code adopted by Board rule applies where local amendments do not govern.

  • Unlicensed electrical work may result in Board discipline, administrative penalties, and misdemeanor prosecution under the Oklahoma Electrical Licensing Act.

OK Electrician key terms

Approved

Acceptable to the authority having jurisdiction. Approval may rest on listing or labeling by a qualified electrical testing laboratory, or on other evidence that the equipment or material is suitable for the specific use.

Related: Listed, Labeled, Authority Having Jurisdiction (AHJ)
Listed

Equipment, materials, or services included in a published list maintained by a nationally recognized testing laboratory, stating that the item meets designated standards or has been tested and found suitable for a specified purpose.

Related: Labeled, Approved
Labeled

Equipment or material to which a label, symbol, or other identifying mark of a nationally recognized testing laboratory has been attached, showing that it has been evaluated and meets the applicable product standard.

Related: Listed, Approved
Authority Having Jurisdiction (AHJ)

The organization, office, or individual responsible for enforcing the code or approving equipment, materials, an installation, or a procedure. In Oklahoma this is usually the local electrical inspector or building official.

Related: Approved, Qualified Person
Qualified Person

A person who has the skills and knowledge related to the construction and operation of the electrical equipment and installations, and who has received safety training to recognize and avoid the electrical hazards involved.

Related: Authority Having Jurisdiction (AHJ), Working Clearance
Working Clearance

The space required to be kept clear in front of electrical equipment so a person can safely work on it. It has minimum depth, width, and height dimensions and must not be used for storage.

Related: Qualified Person, Authority Having Jurisdiction (AHJ)
Ampacity

The maximum current, in amperes, that a conductor can carry continuously under the conditions of use without exceeding its temperature rating. Ampacity is adjusted for ambient temperature and for the number of current-carrying conductors.

Related: Overcurrent, Overload
Branch Circuit

The circuit conductors between the final overcurrent device protecting the circuit and the outlet or outlets. Branch circuits may be general purpose, appliance, or individual circuits, and may be multiwire.

Related: Feeder, Overcurrent, Continuous Load
Feeder

All circuit conductors between the service equipment, the source of a separately derived system, or other power supply source and the final branch-circuit overcurrent device.

Related: Branch Circuit, Service-Entrance Conductors
Continuous Load

A load in which the maximum current is expected to continue for three hours or more. Conductors and overcurrent devices serving continuous loads are generally sized at 125 percent of the load.

Related: Branch Circuit, Feeder
Service Point

The point of connection between the serving utility's facilities and the premises wiring. It marks where utility responsibility ends and where National Electrical Code requirements begin for the premises installation.

Related: Service-Entrance Conductors, Authority Having Jurisdiction (AHJ)
Service-Entrance Conductors

The conductors between the terminals of the service equipment and the service point, including any conductor connected to the service drop or service lateral.

Related: Service Point, Feeder
Ground-Fault Circuit Interrupter (GFCI)

A device intended for protection of people that de-energizes a circuit or portion of it within an established time when current to ground exceeds a value below that required to protect equipment, typically about 5 milliamperes.

Related: Ground Fault, Equipment Grounding Conductor (EGC)
Arc-Fault Circuit Interrupter (AFCI)

A device that recognizes characteristic arcing faults in branch-circuit wiring and opens the circuit. The code requires them on many 120-volt, 15- and 20-ampere dwelling-unit branch circuits.

Related: Branch Circuit, Overcurrent
Overcurrent

Any current in excess of the rated current of equipment or the ampacity of a conductor. Overcurrent may result from an overload, a short circuit, or a ground fault.

Related: Overload, Ground Fault
Overload

Operation of equipment in excess of its normal full-load rating, or of a conductor in excess of its rated ampacity, that persists long enough to cause damage. A short circuit or ground fault is not an overload.

Related: Overcurrent, Motor Overload Protection
Ground Fault

An unintentional, electrically conductive connection between an ungrounded conductor and the normally non-current-carrying conductors, metal enclosures, metal raceways, metal equipment, or the earth.

Related: Ground-Fault Circuit Interrupter (GFCI), Effective Ground-Fault Current Path
Equipment Grounding Conductor (EGC)

The conductive path installed to connect normally non-current-carrying metal parts of equipment together and to the system grounded conductor or grounding electrode conductor, providing a low-impedance path for fault current.

Related: Grounding Electrode Conductor (GEC), Bonding Jumper, Effective Ground-Fault Current Path
Grounding Electrode Conductor (GEC)

The conductor used to connect the system grounded conductor, the equipment, or both, to a grounding electrode or to a point on the grounding electrode system.

Related: Equipment Grounding Conductor (EGC), Grounded Conductor
Bonding Jumper

A reliable conductor that ensures electrical conductivity between metal parts required to be electrically connected, such as the main bonding jumper at service equipment or an equipment bonding jumper around a raceway.

Related: Equipment Grounding Conductor (EGC), Grounded Conductor
Effective Ground-Fault Current Path

An intentionally constructed, low-impedance conductive path designed and intended to carry current under ground-fault conditions from the point of a ground fault to the source, so that overcurrent devices operate promptly.

Related: Equipment Grounding Conductor (EGC), Ground Fault
Grounded Conductor

A system or circuit conductor that is intentionally connected to earth, commonly called the neutral. It normally carries current and is not the same as the equipment grounding conductor.

Related: Grounding Electrode Conductor (GEC), Equipment Grounding Conductor (EGC)
Selective Coordination

Localization of an overcurrent condition to restrict outages to the circuit or equipment affected, accomplished by selecting and installing overcurrent protective devices so that their operating characteristics coordinate with upstream devices.

Related: Overcurrent
Sheathed Cable

A factory assembly of two or more insulated conductors enclosed in an overall moisture-resistant, flame-retardant jacket, commonly used in dwelling units and permitted only where the code allows.

Related: Raceway, Box Fill
Raceway

An enclosed channel of metal or nonmetallic material designed expressly for holding wires, cables, or busbars, with additional functions as permitted by the code, such as EMT, IMC, or rigid PVC.

Related: Sheathed Cable, Box Fill
Box Fill

The internal volume required for an outlet, junction, or device box, calculated from the number and size of conductors, devices, fittings, and grounding conductors, so that the box is not overcrowded.

Related: Raceway, Sheathed Cable
Flexible Cord

A factory assembly of stranded conductors with flexible insulation and an outer jacket, used to connect appliances and portable equipment; it may not be used as a substitute for fixed wiring.

Related: Raceway, Luminaire
Luminaire

A complete lighting unit consisting of a light source together with the parts designed to position, protect, and supply power to it, and to distribute the light.

Related: Flexible Cord
Motor Overload Protection

Protection intended to prevent a motor from overheating because of sustained overloads or failure to start, sized from the motor nameplate current; it does not provide short-circuit or ground-fault protection.

Related: Motor Branch-Circuit Short-Circuit and Ground-Fault Protective Device, Overload
Motor Branch-Circuit Short-Circuit and Ground-Fault Protective Device

The fuse or circuit breaker protecting motor branch-circuit components from short circuits and ground faults. It is sized larger than overload protection and may be part of a listed combination motor controller.

Related: Motor Overload Protection, Selective Coordination
Hermetic Refrigerant Motor-Compressor

A motor-compressor enclosed in the same housing, with the motor cooled by refrigerant. Its nameplate rated-load current is used to size conductors and protection under Article 440.

Related: Motor Overload Protection, Motor Branch-Circuit Short-Circuit and Ground-Fault Protective Device
Hazardous (Classified) Location

A location where fire or explosion hazards may exist because of flammable gases, vapors, dusts, fibers, or flyings. Equipment installed there must be approved for the specific class, division or zone, and group.

Related: Intrinsically Safe Circuit
Intrinsically Safe Circuit

A circuit in which any spark or thermal effect is incapable of causing ignition of a flammable or combustible mixture, under normal operating conditions and under specified fault conditions, because its energy is limited.

Related: Hazardous (Classified) Location
Class 2 Circuit

The portion of the wiring system between the load side of a Class 2 power source and the connected equipment, limited in power and voltage so that it presents a low fire and electric shock hazard.

Related: Communications Circuit
Communications Circuit

A circuit that carries signals for telephone, data, cable television, or similar purposes, installed under Article 800 and kept separated from power and lighting circuits by the required spacing and barriers.

Related: Class 2 Circuit
Construction Industries Board (CIB)

The Oklahoma state agency that licenses electrical contractors, journeymen, and apprentices, adopts licensing rules, and enforces the Electrical Licensing Act through its electrical division.

Related: Electrical Contractor License, Journeyman Electrician
Electrical Contractor License

In Oklahoma, the state credential held by a business or individual that contracts to perform electrical work for the public, responsible for obtaining permits and ensuring the work meets code.

Related: Construction Industries Board (CIB), Journeyman Electrician, Continuing Education
Journeyman Electrician

A person licensed by the state to install, alter, and repair electrical systems, who may work without direct supervision and may supervise apprentices on the job.

Related: Apprentice Electrician, Electrical Contractor License
Apprentice Electrician

A person registered with the state who is learning the trade and must work under the supervision of a licensed journeyman or contractor while accumulating the hours needed for a journeyman license.

Related: Journeyman Electrician
Continuing Education

Approved instruction in code changes, safety, and related trade topics that an Oklahoma electrician must complete during each license renewal cycle to keep the license active.

Related: Electrical Contractor License, Journeyman Electrician

OK Electrician study plan

8 weeks · About 8 hours per week

Week 1

Wiring Methods and Materials (NEC Chapter 3) & General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

  • Map every Chapter 3 wiring method (NM, AC, MC, EMT, IMC, RMC, PVC, LFMC, ENT) to its permitted locations, uses not permitted, and support/securement intervals

  • Calculate conductor ampacity adjustments for bundling and ambient temperature using the Table 310.16 starting point

  • Apply Article 100 definitions to distinguish among outlet, receptacle, device, and premises wiring

  • Interpret Article 110 working-clearance and dedicated-equipment-space rules dimension-by-dimension

Your checkpoint

One-page comparison table of all Chapter 3 wiring methods plus 25 self-written practice items scored at 80% or better

Week 2

Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250)

  • Size and locate overcurrent devices using the next-size-up rule and the tap-conductor allowances in 240.21

  • Determine conductor and enclosure bonding jumpers from Table 250.102 and size equipment grounding conductors from Table 250.122

  • Select the correct grounding electrode system and apply the 25-ohm and supplementary-electrode requirements of 250.53

  • Differentiate grounding from bonding in service, separately derived, and multi-building applications

Your checkpoint

Completed grounding and bonding worksheet of 20 calculated scenarios, each with code section citations, reviewed for errors

Week 3

Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230)

  • Compute service and feeder loads using Articles 220 methods applied through Article 230

  • Size service-entrance conductors, service disconnects, and grounding for one- and two-family dwellings

  • Calculate branch-circuit requirements for small-appliance, laundry, and general lighting loads

  • Apply Article 225 rules for outside branch circuits and feeders, including clearances and masts

Your checkpoint

Full residential service calculation for a 2,400 sq ft dwelling including load summary, conductor sizing, and overcurrent selection

Week 4

Equipment for General Use (NEC Articles 400-460) & Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6)

  • Apply Article 410 luminaire and Article 406 receptacle requirements to real installation layouts

  • Size and select flexible cords and cables, switches, and panelboards per Articles 400, 404, and 408

  • Identify which Article 500/502/503 class-division rules drive wiring method changes in hazardous locations

  • Contrast dwelling-unit, commercial, and assembly-occupancy requirements in Chapters 5 and 6

Your checkpoint

Two timed 40-question practice sets on Domains 5 and 6, each scored at 75% or better with every miss written up

Week 5

Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6) & Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440)

  • Determine motor branch-circuit, feeder, and overload protection sizing using Article 430 tables and 125%/430.52 rules

  • Calculate motor disconnecting means, controller rating, and conductor ampacity from nameplate data

  • Apply Article 440 rules to hermetic refrigerant motor-compressors and room air conditioners

  • Resolve special-occupancy conflicts such as health care, places of assembly, and swimming pools against Chapter 3 methods

Your checkpoint

Five fully worked motor and A/C calculation problems (branch circuit, feeder, overload, disconnect) with cited tables

Week 6

Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440) & Special Systems and Communications Circuits (NEC Chapters 7-8)

  • Build a one-page motor calculation decision flow from nameplate to final overcurrent device

  • Distinguish Class 1, 2, and 3 circuits and apply Article 725 separation and wiring requirements

  • Summarize Article 760 fire alarm, Article 800 communications, and Article 820 CATV requirements and their non-power-limited limits

  • Compare Chapter 7 and Chapter 8 scope rules and identify where Article 300 does not apply

Your checkpoint

Two-page summary sheet of Chapters 7 and 8 scope, separation, and wiring rules with 15 self-test questions attached

Week 7

Oklahoma Electrical Licensing Statutes and Administrative Rules & General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

  • Outline the Oklahoma Electrical Licensing Act requirements for licensure, scope of work, and exemptions

  • State the Oklahoma Administrative Rules provisions on continuing education, license renewal, and disciplinary actions

  • Determine bonding and insurance obligations and the enforcement authority of the state Electrical Board

  • Re-review Article 110 inspection requirements and identify what an Oklahoma inspector checks at rough-in and final

Your checkpoint

Closed-book quiz on Oklahoma statutes and rules scored at 85% or better, plus a one-page licensing checklist

Week 8

Wiring Methods and Materials (NEC Chapter 3) & Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250) & Services, Feeders, and Branch Circuits (NEC Articles 210, 215, 225, 230) & Equipment for General Use (NEC Articles 400-460) & Special Occupancies, Special Conditions, and Special Equipment (NEC Chapters 5-6) & Motors, Air Conditioning, and Industrial Controls (NEC Articles 430, 440) & Special Systems and Communications Circuits (NEC Chapters 7-8) & Oklahoma Electrical Licensing Statutes and Administrative Rules & General Requirements, Definitions, and Inspection (NEC Articles 100, 110)

  • Take three full-length timed practice exams of 80 questions under exam conditions

  • Re-work every missed item from weeks 1 through 7 and tag root cause as calculation, code lookup, or misread

  • Drill high-frequency lookup tables (310.16, 250.122, 430.52, 430.250) to under 60 seconds each

  • Finalize a personal index of the 30 code sections you missed most often

Your checkpoint

Three practice exam scores averaging 80% or better with a completed error-analysis log and personal section index

Milestones

Week 4: Score 75% or better on a 40-question mix drawn from Domains 2, 3, and 4, with no more than two missed items from conductor or overcurrent sizing

Week 6: Complete the motor and A/C calculation set with 4 of 5 answers correct and every answer traceable to a cited table

Week 8: Average 80% or better across three full-length timed practice exams, with the Oklahoma licensing quiz above 85%

OK Electrician exam day

Your checklist

Government-issued photo ID

Bring the original (not a photocopy) - driver's license, state ID, passport, or military ID. The name must match your exam registration exactly; a name mismatch can block you from testing. Confirm with the provider which ID forms they accept and whether a second form is required.

Appointment confirmation / admission letter

Print the scheduling confirmation or authorization-to-test notice you received when you booked. Some centers ask for it; having it also gives you the exact address, check-in time, and your candidate ID number.

Approved calculator

A basic non-programmable calculator with no communication capability. Programmable, graphing, and cellular-capable devices are almost always barred, and phones or smartwatches cannot substitute. Confirm with the provider whether calculators are supplied or whether yours must be inspected and cleared.

Code book and reference materials

Oklahoma electrical exams are commonly open-book, but the allowed edition and whether tabs, highlighting, or handwritten notes are permitted vary. Confirm with the provider which NFPA 70/NEC edition is in effect and what annotations are allowed before you write in your book.

Pencils and scratch paper expectations

Many test centers issue pencils and blank scratch paper and collect them afterward; others let you bring your own. Confirm with the provider so you are not turned away for carrying items they disallow.

Simple wristwatch (non-smart)

A basic analog or digital watch lets you pace yourself if the testing computer's clock is not visible from your seat. Smartwatches, fitness bands, and any device with messaging capability are prohibited.

Prohibited items left at home or in the car

Phone, smartwatch, earbuds, study notes, flash cards, bags, hats, and food or drink are typically not allowed in the testing room. Find out in advance whether the center provides a locker and whether you can reach your belongings during a break.

Directions, parking, and travel buffer

Do a route check the day before. Know the building, floor, and suite, and identify parking or transit options so a wrong turn does not cost you your appointment. Confirm with the provider how late you may arrive before your seat is forfeited.

Accommodation request (if needed)

Extra time, a separate room, or medical accommodations usually require an advance request with documentation, not a same-day ask. If you need one, contact the provider immediately - well before exam day - to find out the deadline.

Layers and personal comfort items

Testing rooms are often cold and sessions are long. A light layer you can remove, plus any permitted medical items (such as an inhaler or glucose tablets), should be cleared with the provider at check-in.

Know your scoring and retake basics

Before test day, know the passing score, whether results are immediate or mailed, and how a retake works if you do not pass. Confirm these details with the provider or the Oklahoma Construction Industries Board rather than relying on secondhand information.

Plan the day

Final 72 hours

Confirm your appointment date, time, and test-center address, and re-read the provider's candidate bulletin for ID and materials rules. Verify which code book edition is adopted in Oklahoma and whether tabs or notes are allowed, then set up your book the way the rules permit. Do light review of your weakest topics - motor calculations, box fill, conduit fill, grounding - using practice lookups rather than new material. Stop heavy cramming the night before.

24 hours before

Pack your bag: photo ID, printed confirmation, approved calculator, pencils, watch, and code book if allowed. Lay out clothes and set two alarms. Do a dry run of the route or check traffic and transit schedules. Eat a normal dinner, avoid alcohol, and go to bed at your usual time. Do not start a new study topic you cannot finish.

Morning of

Eat a real breakfast and hydrate, but not so much that you need frequent bathroom breaks. Arrive at the center early - plan on 30 minutes before your appointment unless the provider states otherwise. Keep your phone off and stowed before you enter the building. At check-in, present your ID, accept the locker or storage instructions, and follow the proctor's sign-in and security steps exactly.

During the test

Read the instructions screen and note the time limit and question count. Work in passes: answer the questions you know first, flag the long calculation or lookup items, and come back to them. Use the code book index and article headings rather than flipping page by page, and check units and whether the question asks for conductor size, overcurrent size, or both. Watch the clock - roughly divide remaining time by remaining questions. If you finish early, use leftover time to re-check flagged items and confirm you answered every question.

Rules to check

  • Bring only materials the provider has approved, and hand over anything the proctor asks for. Unapproved notes, phones, or smart devices found at your seat can void your score regardless of intent.

  • Your photo ID must be current, unexpired, and match the name on your registration. If your name recently changed, bring the documentation the provider requires - confirm the accepted forms in advance.

  • No talking, gesturing, or sharing materials with other candidates once testing begins. Raise your hand and wait for the proctor if you have a problem with your workstation or need to leave the room.

  • Phones must be powered off and stored as directed - not merely silenced or in a pocket. If your device makes noise or is found on your person, expect the proctor to end your session.

  • Break policy varies by provider: some allow scheduled breaks, and the clock generally keeps running during them. Confirm the break rules and whether you may access your locker before test day.

  • The passing score is set by the licensing authority or the testing provider, not by the test center staff. Confirm the required score and how and when results are reported so you know what to expect at the end of the session.

  • Scratch paper and any issued materials usually must be returned before you leave. Do not copy, photograph, or remove exam content - doing so is a testing-integrity violation.

  • If you arrive late or without acceptable ID, the center may deny you a seat and your fee may not be refunded. Confirm the provider's late-arrival and rescheduling policy in writing beforehand.

OK Electrician FAQ

How many OK Electrician practice questions are available?

The practice set has 200 OK Electrician questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many OK Electrician flashcards are available?

The flashcard set has 32 OK Electrician cards. Each card shows the term and its definition.

Which topics does the OK Electrician study material cover?

The OK Electrician study material has 9 sections, including General Requirements, Definitions, and Inspection (NEC Articles 100, 110), Wiring Methods and Materials (NEC Chapter 3), and Overcurrent Protection, Grounding, and Bonding (NEC Articles 240, 250).

What format facts does the catalog list for the OK Electrician exam?

The catalog lists these item types: multiple choice for the OK Electrician exam.