MI Journeyman Electrician Practice Test

Michigan Journeyman Electrician

MI Journeyman Electrician overview

  • 200 practice questions
  • 32 flashcards
  • 5 study guide topics
  • 36 key terms

What you'll study

  • General Electrical Knowledge and Code Administration20%
  • Services, Feeders, and Branch Circuits20%
  • Wiring Methods, Materials, and Raceways20%
  • Equipment, Devices, and Utilization Equipment20%
  • Grounding, Bonding, Overcurrent Protection, and Special Occupancies20%

The Michigan Journeyman Electrician credential is a skilled-trades license administered through the Michigan Department of Licensing and Regulatory Affairs (LARA) and its Bureau of Construction Codes. Applications, renewals, license lookups, and complaints are handled through LARA's online licensing portals rather than through a separate electrical board website. The license is the standard stepping stone for electricians who have completed their apprenticeship hours and want to work unsupervised on electrical installations, and it is commonly the prerequisite candidates hold before pursuing a master electrician license or contractor registration.

The examination is a code-based, closed-book-style knowledge test covering the full span of electrical installation work: general electrical knowledge and code administration; services, feeders, and branch circuits; wiring methods, materials, and raceways; equipment, devices, and utilization equipment; and grounding, bonding, overcurrent protection, and special occupancies. Expect a heavy emphasis on locating and applying Code rules quickly rather than on memorized trivia, plus a working layer of Ohm's law, box and conduit fill, conductor ampacity, and load calculations.

Preparation should combine a current Codebook with a tabbing and indexing strategy, structured practice on calculation families, and timed drilling on the topics you miss most. Note that the official Michigan pages used for this profile could not be retrieved (the licensing URLs returned a not-found page), so administrative specifics such as fees, question count, time limit, passing score, and retake rules are intentionally left blank here. Confirm those details directly with LARA before you schedule.

Common mistakes

Sizing a device or junction box by counting conductors and multiplying by a single volume number, ignoring equipment grounding conductors, cable clamps, support fittings, and the volume allowance taken per device yoke.

Candidates memorize the conductor volume table but skip the extra allowance items in the box-fill rules, and they treat box fill the same way they treat conduit fill.

What to do instead

Work the box-fill problem in a fixed sequence: total the volume allowance for each conductor by size, add one allowance for all equipment grounding conductors based on the largest one, add one allowance for clamps and one for support fittings, and add one allowance for each yoke or device based on the largest conductor landing on it; then compare to the marked box volume.

Sizing the overcurrent device for a branch circuit or feeder at 100 percent of a continuous load, or applying the 125 percent continuous-load multiplier to the conductor ampacity but not the overcurrent device (or the reverse).

The continuous-load multiplier is learned as a single rule and then applied to only one side of the calculation, and receptacle/lighting loads are assumed to be noncontinuous by habit.

What to do instead

Separate the two calculations on scratch paper. Conductors: 125 percent of continuous load plus 100 percent of noncontinuous load. Overcurrent device: same 125/100 split unless the assembly is listed for 100 percent. Label each line so the multiplier is never dropped or double-applied.

Sizing an equipment grounding conductor from the grounding electrode conductor table, or sizing a grounding electrode conductor from the equipment grounding conductor table, so a 400 A service gets an undersized or oversized conductor.

Both tables use conductor-size lookups and are studied back-to-back, so the trigger for each one gets blurred.

What to do instead

Tie each table to its question: if the question asks about the conductor that runs with the circuit conductors and carries fault current, the driver is the overcurrent device rating. If it asks about the conductor to the electrode, the driver is the service conductor size. Say the driver out loud before opening either table.

Rounding up to the next standard overcurrent device rating on a multioutlet branch circuit that supplies receptacle outlets for cord-and-plug-connected portable loads, or rounding up past the small-conductor limits.

The next-size-up provision is remembered as a blanket permission and the listed conditions attached to it are forgotten.

What to do instead

Before rounding up, check that the circuit is not a multioutlet branch circuit feeding cord-and-plug portable loads, that the conductor ampacity does not already match a standard rating, that the next standard size does not exceed the 800 A ceiling, and that the small-conductor limits are still satisfied.

Limiting ground-fault circuit-interrupter protection to bathroom receptacles and missing kitchen countertops, laundry areas, garages, outdoors, unfinished basements, and receptacles near sinks; likewise assuming arc-fault protection applies only to bedroom outlets.

Study material is often organized around the room named in an older memory aid rather than the current list of locations and outlet types.

What to do instead

Build a location checklist from the code article itself for each occupancy and walk every question through the full list rather than stopping at the first location that matches. Treat AFCI and GFCI as separate lists and check each independently.

Ignoring ampacity adjustment for more than three current-carrying conductors in a raceway, or counting every neutral as a current-carrying conductor in a balanced multiwire branch circuit and over-adjusting.

Conduit fill and ampacity adjustment are treated as one topic, and the neutral-counting rules are more nuanced than the general adjustment rule.

What to do instead

Count current-carrying conductors first, apply the neutral rules only to the specific circuit type in the question, then apply the adjustment factor to the ampacity before any termination correction. Keep the adjustment step and the termination step as two separate lines of the calculation.

Using the motor nameplate current or the branch-circuit short-circuit and ground-fault protective device rating when selecting overload protection, or using the overload rating to size branch-circuit conductors.

Three different motor values (full-load current from the tables, branch-circuit protection, and overload protection) are learned together and swapped under time pressure.

What to do instead

Assign each motor value a job before computing: table full-load current drives conductor sizing, the short-circuit and ground-fault device protects the circuit, and the overload device protects the motor. Never let one value substitute for another in the next step.

Selecting conductor ampacity from the 90 degrees C column for the final termination on a 100 A-or-less circuit, or from the 60 degrees C column on a circuit above 100 A, without checking the termination rating.

The highest column gives the largest allowable ampacity and is chosen reflexively, and the temperature-correction and adjustment steps are done in the wrong order.

What to do instead

Set the rule on scratch paper: terminations of 100 A or less default to the 60 degrees C column unless the equipment is listed and identified otherwise, and terminations over 100 A use the 75 degrees C column. Use the higher column only for correction and adjustment calculations, then take the lower of the adjusted value and the termination-limited value.

Measuring working clearance depth from the wall or from the floor-mounted equipment front rather than from the live parts, and forgetting the required width and headroom.

Clearance is visualized as floor space in front of a panel instead of a defined volume measured from exposed live parts.

What to do instead

For every clearance question, first mark the live parts, then measure depth from them, add the required width around the equipment, and confirm the headroom. Check the dedicated equipment space above and below the equipment as a separate item.

Answering from habit, handbook commentary, or jobsite practice instead of the adopted code text, and assuming the current national edition applies without confirming the edition and state amendments in force.

Experienced candidates rely on how their jurisdiction used to inspect, and code editions change article numbering and requirements between cycles.

What to do instead

Before an exam sitting, confirm which edition and which state amendments are examinable, then practice every question as a text lookup exercise: find the article, read the actual requirement and its exceptions, and only then choose the answer.

Exam requirements can change. Confirm current details with the exam provider.

MI Journeyman Electrician practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1General Electrical Knowledge and Code Administration

    What is the stated purpose of the National Electrical Code?

    1. To guarantee efficient operation of electrical systems
    2. To establish the rates utilities may charge for power
    3. To prescribe manufacturing standards for electrical products
    4. To safeguard persons and property from electrical hazards Correct answer.

    Explanation

    The Code exists for the practical safeguarding of persons and property from hazards arising from the use of electricity. It is an installation code, not a design manual, a product standard, or a rate schedule.

  2. Question 2General Electrical Knowledge and Code Administration

    Ampacity is best described as which of the following?

    1. The continuous current its temperature rating allows Correct answer.
    2. The voltage at which the insulation is rated
    3. The current at which the overcurrent device trips
    4. The short-circuit withstand rating of the conductor

    Explanation

    Ampacity is the current a conductor can carry continuously under the conditions of use without exceeding its temperature rating. Insulation life and termination limits are both governed by that temperature.

  3. Question 3General Electrical Knowledge and Code Administration

    The working space in front of electrical equipment must have a minimum width of which of the following?

    1. 30 in. or the width of the equipment, whichever is greater Correct answer.
    2. 42 in. measured outward from the equipment centerline
    3. 24 in. or the width of the equipment, whichever is greater
    4. 36 in. regardless of the width of the equipment

    Explanation

    The clear working space must be at least 30 in. wide, or the width of the equipment if that is greater, and it must extend from the floor to the required headroom.

  4. Question 4General Electrical Knowledge and Code Administration

    A 125-volt, 20-ampere receptacle installed in a dwelling-unit bathroom must be which of the following?

    1. Installed within 12 inches of the floor
    2. Protected by a ground-fault circuit interrupter Correct answer.
    3. Connected to the small-appliance branch circuit
    4. Supplied by a dedicated 30-ampere circuit

    Explanation

    Receptacles rated 125 V, 15 or 20 A in dwelling-unit bathrooms require ground-fault circuit-interrupter protection. The requirement addresses the shock hazard created by water and grounded surfaces near the basin.

  5. Question 5General Electrical Knowledge and Code Administration

    In a dwelling unit, receptacles along a wall must be arranged so that no point along the floor line is more than what distance from a receptacle outlet?

    1. 6 ft Correct answer.
    2. 4 ft
    3. 8 ft
    4. 10 ft

    Explanation

    Receptacle outlets must be installed so that no point along the floor line of the wall space is more than 6 ft from an outlet. This generally spaces receptacles no more than 12 ft apart.

  6. Question 6General Electrical Knowledge and Code Administration

    A branch circuit wired with 14 AWG copper conductors may be protected by an overcurrent device with a maximum rating of which of the following?

    1. 15 amperes Correct answer.
    2. 25 amperes
    3. 20 amperes
    4. 30 amperes

    Explanation

    For 14 AWG copper, the small-conductor rule limits the branch-circuit overcurrent device to 15 A. That matches the 60 degrees C ampacity of the conductor.

  7. Question 7General Electrical Knowledge and Code Administration

    Receptacles are prohibited in a zone extending how far horizontally from the top of a bathtub rim or shower stall threshold?

    1. 6 ft
    2. 3 ft Correct answer.
    3. 8 ft
    4. 5 ft

    Explanation

    Receptacles may not be installed within a zone measured 3 ft horizontally and 8 ft vertically from the top of a bathtub rim or shower stall threshold. The zone keeps cord-connected appliances out of reach of a person in the tub or shower.

  8. Question 8General Electrical Knowledge and Code Administration

    In Michigan, a person who performs electrical work for another person for compensation generally must do which of the following?

    1. Hold a license issued under the state Electrical Administrative Act Correct answer.
    2. Obtain only a local building permit, with no state license
    3. Register with the electric utility that serves the premises
    4. Carry a manufacturer certification for the equipment installed

    Explanation

    Michigan regulates electricians through the Electrical Administrative Act, which requires licensure to perform electrical work for compensation. Permits, utility registration, and product certifications are separate matters and do not authorize the work.

  9. Question 9General Electrical Knowledge and Code Administration

    A box has a volume of 21.0 cubic inches. If each 12 AWG conductor is counted at 2.25 cubic inches, what is the maximum number of 12 AWG conductors the box may contain?

    1. 11 conductors
    2. 9 conductors Correct answer.
    3. 10 conductors
    4. 8 conductors

    Explanation

    Divide the box volume by the volume allowance per conductor: 21.0 divided by 2.25 equals 9.33. Only whole conductors count, so the box may contain no more than 9 of them.

  10. Question 10General Electrical Knowledge and Code Administration

    Where three or more conductors are installed in a raceway, the conductors may occupy no more than what percentage of the raceway's cross-sectional area?

    1. 40 percent Correct answer.
    2. 31 percent
    3. 60 percent
    4. 25 percent

    Explanation

    Raceway fill limits are 53 percent for one conductor, 31 percent for two conductors, and 40 percent for three or more conductors. The limits leave room for conductor installation and heat dissipation.

  11. Question 11General Electrical Knowledge and Code Administration

    Six current-carrying 10 AWG THHN conductors are installed in a single raceway. What ampacity adjustment factor applies?

    1. 50 percent
    2. 100 percent
    3. 70 percent
    4. 80 percent Correct answer.

    Explanation

    The adjustment table applies an 80 percent factor to circuits with four to six current-carrying conductors in a raceway or cable. The factor accounts for the reduced ability to dissipate heat when conductors are bundled.

  12. Question 12General Electrical Knowledge and Code Administration

    Conductors from 14 AWG through 1 AWG on circuits rated 100 amperes or less are generally required to be terminated using ampacities from which temperature column?

    1. 90 degrees C
    2. 75 degrees C
    3. The temperature marked on the conductor insulation
    4. 60 degrees C Correct answer.

    Explanation

    Terminations on circuits of 100 A or less using 14 AWG through 1 AWG conductors are limited to the 60 degrees C column unless the equipment is listed and identified for a higher temperature. The 90 degrees C column is used only for adjustment and correction calculations.

  13. Question 13General Electrical Knowledge and Code Administration

    The Code recommends that voltage drop on a feeder plus branch circuit, taken together, not exceed what percentage of the supply voltage?

    1. 8 percent
    2. 5 percent Correct answer.
    3. 3 percent
    4. 10 percent

    Explanation

    Informational notes recommend a maximum total voltage drop of 5 percent for feeder plus branch circuit, with no more than 3 percent on the branch circuit alone. These values are recommendations rather than mandatory rules.

  14. Question 14General Electrical Knowledge and Code Administration

    A 25-horsepower, 460-volt, three-phase motor has a full-load current of 34 amperes. Using a standard inverse-time circuit breaker for branch-circuit short-circuit and ground-fault protection, what is the maximum rating generally permitted?

    1. 102 amperes
    2. 68 amperes
    3. 85 amperes Correct answer.
    4. 119 amperes

    Explanation

    An inverse-time circuit breaker protecting a motor branch circuit may generally be set no higher than 250 percent of the motor full-load current. Here 2.50 times 34 amperes equals 85 amperes.

  15. Question 15General Electrical Knowledge and Code Administration

    Where a metal underground water pipe is used as a grounding electrode, the Code requires that the electrode be which of the following?

    1. Sized from the ampacity of the service-entrance conductors
    2. Bonded to the building steel with a 6 AWG conductor
    3. Supplemented by an additional grounding electrode Correct answer.
    4. Isolated from all interior metal piping

    Explanation

    A metal underground water pipe electrode must be supplemented by an additional electrode such as a ground rod or a concrete-encased electrode. The reason is that the pipe may later be replaced or repaired with a nonmetallic section.

  16. Question 16General Electrical Knowledge and Code Administration

    A 20-ampere branch circuit is wired with 12 AWG copper circuit conductors. What is the minimum size copper equipment grounding conductor?

    1. 8 AWG copper
    2. 10 AWG copper
    3. 12 AWG copper Correct answer.
    4. 14 AWG copper

    Explanation

    The equipment grounding conductor sizing table requires an equipment grounding conductor no smaller than 12 AWG copper for a 20-ampere circuit. For 15, 20, and 30 ampere circuits it generally matches the circuit conductor size.

  17. Question 17General Electrical Knowledge and Code Administration

    In a dwelling unit, the laundry branch circuit supplying the laundry receptacle outlets must have a minimum rating of which of the following?

    1. 20 amperes Correct answer.
    2. 15 amperes
    3. 40 amperes
    4. 30 amperes

    Explanation

    At least one 20-ampere branch circuit must be provided for the laundry receptacle outlets in a dwelling unit. That circuit may not supply outlets outside the laundry area.

  18. Question 18General Electrical Knowledge and Code Administration

    Which of the following dwelling-unit branch circuits requires arc-fault circuit-interrupter protection?

    1. A 120-volt, 20-ampere circuit supplying family room receptacles Correct answer.
    2. A 120-volt circuit supplying only an outdoor post light
    3. A 240-volt, 30-ampere circuit supplying a clothes dryer
    4. A 240-volt, 30-ampere circuit supplying a water heater

    Explanation

    Arc-fault protection is required for 120-volt, 15- and 20-ampere branch circuits supplying outlets in family rooms, living rooms, bedrooms, kitchens, and similar dwelling areas. Dedicated 240-volt appliance circuits and outdoor-only lighting are not on that list.

  19. Question 19General Electrical Knowledge and Code Administration

    A surface-mounted incandescent luminaire installed in a clothes closet must be kept at least what distance from the shelf?

    1. 18 inches
    2. 6 inches
    3. 24 inches
    4. 12 inches Correct answer.

    Explanation

    The closet luminaire table sets a 12-inch minimum clearance between a surface-mounted incandescent luminaire and the shelf. Other luminaire types, such as recessed or fluorescent fixtures, have different clearances.

  20. Question 20General Electrical Knowledge and Code Administration

    A junction box used in a wiring system must be which of the following?

    1. Listed for wet locations
    2. Fitted with a grounding bushing
    3. Accessible without removing building finish or structure Correct answer.
    4. Installed only in unfinished areas of a building

    Explanation

    Boxes must remain accessible so that the splices and connections inside them can be inspected and serviced. Accessibility means the box can be reached without cutting or removing any part of the building finish or structure.

  21. Question 21General Electrical Knowledge and Code Administration

    At service equipment, the main bonding jumper provides a connection between which of the following?

    1. The grounded service conductor and the equipment grounding bus Correct answer.
    2. The ungrounded conductors and the metal enclosure
    3. The grounding electrode and the metal water piping system
    4. The equipment grounding conductors and the grounding electrode conductor

    Explanation

    The main bonding jumper connects the grounded service conductor to the equipment grounding terminal bus at the service. This intentional connection creates the low-impedance return path needed for fault current to open the overcurrent device.

  22. Question 22General Electrical Knowledge and Code Administration

    A service is supplied by 2/0 AWG copper service-entrance conductors. What is the minimum size copper grounding electrode conductor where a metal underground water pipe is the electrode?

    1. 8 AWG copper
    2. 6 AWG copper
    3. 2 AWG copper
    4. 4 AWG copper Correct answer.

    Explanation

    For 2/0 AWG copper service conductors, the grounding electrode conductor table requires 4 AWG copper. The allowance that limits rod, pipe, and plate electrode conductors to 6 AWG does not apply to a water pipe electrode.

  23. Question 23General Electrical Knowledge and Code Administration

    Two motors are supplied by one branch circuit. One motor has a full-load current of 10 amperes and the other has a full-load current of 5 amperes. What is the minimum conductor ampacity for the branch circuit?

    1. 20.0 amperes
    2. 17.5 amperes Correct answer.
    3. 15.0 amperes
    4. 18.8 amperes

    Explanation

    A branch circuit supplying several motors is sized at 125 percent of the largest motor full-load current plus the sum of the other motor currents. Here 1.25 times 10 equals 12.5, and 12.5 plus 5 equals 17.5 amperes.

  24. Question 24General Electrical Knowledge and Code Administration

    For a photovoltaic array installed on a building, rapid shutdown must limit conductors within the array boundary to what value?

    1. 80 volts within 30 seconds Correct answer.
    2. 50 volts within 10 seconds
    3. 600 volts within 10 seconds
    4. 30 volts within 30 seconds

    Explanation

    Rapid shutdown must reduce conductors inside the array boundary to 80 volts or less within 30 seconds of initiation. Conductors outside the array boundary must be reduced to 30 volts within the same 30 seconds.

  25. Question 25General Electrical Knowledge and Code Administration

    A dwelling unit has a general lighting load of 8,000 volt-amperes. Using the standard demand factors of 100 percent for the first 3,000 volt-amperes and 35 percent for the remainder up to 120,000 volt-amperes, what is the calculated lighting demand?

    1. 8,000 volt-amperes
    2. 4,750 volt-amperes Correct answer.
    3. 4,000 volt-amperes
    4. 5,250 volt-amperes

    Explanation

    The first 3,000 volt-amperes is taken at 100 percent, giving 3,000 volt-amperes. The remaining 5,000 volt-amperes at 35 percent gives 1,750 volt-amperes, for a total of 4,750 volt-amperes.

  26. Question 26General Electrical Knowledge and Code Administration

    An energized 120/208-volt panelboard is installed in a room where there are no live parts on the opposite side of the aisle. What is the minimum depth of the working space required in front of the panelboard?

    1. 36 in Correct answer.
    2. 42 in
    3. 48 in
    4. 30 in

    Explanation

    NEC Table 110.26(A)(1) sets the minimum depth of working space in front of electrical equipment. Where the equipment operates at 150 volts to ground or less and no live parts are exposed on the opposite side of the aisle, the required depth is 3 ft (36 in). Greater depths apply only where live parts are exposed across the aisle.

  27. Question 27General Electrical Knowledge and Code Administration

    Between any two pull points in a run of electrical metallic tubing, the total accumulated bend shall not exceed which of the following?

    1. 360 degrees Correct answer.
    2. 180 degrees
    3. 270 degrees
    4. 540 degrees

    Explanation

    NEC 358.26 limits the total bend between pull points to the equivalent of four quarter bends, which is 360 degrees. Keeping within this limit allows conductors to be pulled without damage to insulation or excessive strain on the raceway.

  28. Question 28General Electrical Knowledge and Code Administration

    In Michigan, before regulated electrical work begins on a new commercial building, the installer must first do which of the following?

    1. Notify the serving utility and wait for its approval of the wiring method
    2. Submit a set of as-built drawings to the state electrical board
    3. Post a signed completion certificate at the job site
    4. Obtain an electrical permit from the enforcing agency Correct answer.

    Explanation

    Michigan's Electrical Administrative Act and the adopted electrical code require an electrical permit from the enforcing agency before regulated electrical work is started, so the installation can be inspected in stages. Working without the required permit can result in citations, additional fees, and required removal or re-inspection of covered work.

  29. Question 29General Electrical Knowledge and Code Administration

    In a dwelling unit living room, what is the maximum distance measured along the floor line from any point on a wall space to the nearest receptacle outlet?

    1. 4 ft
    2. 5 ft
    3. 6 ft Correct answer.
    4. 3 ft

    Explanation

    NEC 210.52(A) requires receptacle outlets in dwelling unit rooms so that no point along the floor line of any wall space is more than 6 ft from an outlet. This spacing limits reliance on extension cords and cords run across walkways.

  30. Question 30General Electrical Knowledge and Code Administration

    A 60-ampere, three-phase branch circuit is protected by a 60-ampere circuit breaker. What is the minimum size copper equipment grounding conductor permitted for this circuit?

    1. 12 AWG
    2. 6 AWG
    3. 8 AWG
    4. 10 AWG Correct answer.

    Explanation

    NEC Table 250.122 sizes the equipment grounding conductor according to the rating of the overcurrent device protecting the circuit. For a 60-ampere device, the minimum copper equipment grounding conductor is 10 AWG.

  31. Question 31General Electrical Knowledge and Code Administration

    A single driven ground rod serves as the grounding electrode for a service. When measured, its resistance to earth is 40 ohms. What does the Code require in this situation?

    1. No action is needed because any resistance below 50 ohms is acceptable.
    2. The rod must be replaced with a concrete-encased electrode.
    3. The grounding electrode conductor must be increased one trade size.
    4. A second electrode of a listed type must be installed and bonded to the first. Correct answer.

    Explanation

    NEC 250.53(A)(2) requires a single rod, pipe, or plate electrode to be supplemented by an additional electrode unless its resistance to earth is 25 ohms or less. The supplemental electrode must be bonded to the first electrode, and where a second rod is used the rods must be spaced at least 6 ft apart.

  32. Question 32General Electrical Knowledge and Code Administration

    Which statement correctly describes identification of the grounded conductor when a 4 AWG conductor is used as a neutral?

    1. It must be marked with three continuous white stripes along its length.
    2. It may be re-identified with green marking at its terminations.
    3. It must be factory-jacketed white or gray over its entire length.
    4. It may be re-identified with white or gray marking at its terminations. Correct answer.

    Explanation

    NEC 200.6 requires grounded conductors 6 AWG and smaller to be white or gray for their entire length. Conductors 4 AWG and larger may instead be re-identified at terminations using white or gray tape, paint, or similar marking.

  33. Question 33General Electrical Knowledge and Code Administration

    Where must the disconnecting means for a 480-volt motor be located relative to the motor?

    1. Within sight of the motor and within 50 ft of it Correct answer.
    2. Within sight of the motor and within 25 ft of it
    3. In the same room as the controller and equipped with a lock
    4. Anywhere on the same floor of the building as the motor

    Explanation

    NEC 430.102(B) requires a motor disconnecting means that is within sight of the motor and not more than 50 ft from it. This allows a worker to see the disconnect and confirm the motor is de-energized while servicing it.

  34. Question 34General Electrical Knowledge and Code Administration

    A 15-ampere, 125-volt receptacle outlet is installed outdoors on the wall of a dwelling unit to serve a patio. Which of the following is required for this outlet?

    1. It must be GFCI protected. Correct answer.
    2. It must be supplied by a 30-ampere circuit.
    3. It must be bonded to a ground rod at the outlet.
    4. It must be on a dedicated 20-ampere circuit.

    Explanation

    NEC 210.8(A) requires ground-fault circuit-interrupter protection for 125-volt, 15- and 20-ampere receptacle outlets installed outdoors at dwelling units. The protection is required because of the increased shock hazard from moisture and contact with the earth.

  35. Question 35General Electrical Knowledge and Code Administration

    Straight runs of electrical metallic tubing must be securely fastened in place at intervals not exceeding which distance?

    1. Every 6 ft
    2. Every 10 ft Correct answer.
    3. Every 12 ft
    4. Every 15 ft

    Explanation

    NEC 358.30 requires EMT to be fastened within 3 ft of each box, cabinet, fitting, or termination and at intervals not exceeding 10 ft along the run. Proper support keeps the raceway from sagging and prevents strain at terminations.

  36. Question 36General Electrical Knowledge and Code Administration

    What is the minimum permitted clearance of overhead service-drop conductors above a residential driveway?

    1. 10 ft
    2. 18 ft
    3. 12 ft Correct answer.
    4. 15 ft

    Explanation

    NEC 230.24 sets minimum vertical clearances for service-drop conductors above the areas they cross. Above a residential driveway or a parking area the required clearance is 12 ft, measured at the lowest point of the sag.

  37. Question 37General Electrical Knowledge and Code Administration

    A balanced three-phase load of 20 amperes is supplied at 480 volts with a power factor of 0.80. What is the approximate real power drawn by the load?

    1. 13.3 kW Correct answer.
    2. 9.6 kW
    3. 28.8 kW
    4. 16.6 kW

    Explanation

    Real power for a balanced three-phase load is calculated as P = 1.732 x V x I x power factor. Substituting gives 1.732 x 480 V x 20 A x 0.80, which equals approximately 13.3 kW.

  38. Question 38General Electrical Knowledge and Code Administration

    A dwelling unit contains one electric range rated 12 kW. Using NEC Table 220.55, what demand load is used for this range in the service calculation?

    1. 6 kW
    2. 9.6 kW
    3. 8 kW Correct answer.
    4. 12 kW

    Explanation

    NEC Table 220.55 permits household electric ranges to be calculated at less than their nameplate rating. For a single range rated 12 kW or less, the table permits a demand load of 8 kW, which is 80 percent of the maximum range rating.

  39. Question 39General Electrical Knowledge and Code Administration

    A branch circuit supplies a 40-ampere continuous load and a 20-ampere noncontinuous load. What is the minimum rating of the overcurrent device protecting the circuit, assuming the conductors are properly sized?

    1. 80 A
    2. 70 A Correct answer.
    3. 75 A
    4. 60 A

    Explanation

    NEC 210.20(A) requires the overcurrent device to be rated not less than 125 percent of the continuous load plus 100 percent of the noncontinuous load. Here 1.25 x 40 A plus 20 A equals 70 A, which is itself a standard device rating.

  40. Question 40General Electrical Knowledge and Code Administration

    A 120-volt, 20-ampere load is located 100 ft from a panelboard and is wired with 12 AWG copper conductors having a resistance of 1.93 ohms per 1000 ft. What is the approximate voltage drop on the circuit?

    1. 11.6 V
    2. 7.7 V Correct answer.
    3. 15.4 V
    4. 3.9 V

    Explanation

    Voltage drop for a two-wire circuit is computed as 2 x L x R x I, where L is the one-way length in thousands of feet. That gives 2 x 0.100 kft x 1.93 ohms/kft x 20 A, which equals approximately 7.7 volts.

  41. Question 41Services, Feeders, and Branch Circuits

    Overhead service-drop conductors cross a residential driveway that carries only passenger vehicles. What is the minimum vertical clearance required above the driveway surface?

    1. 10 ft
    2. 15 ft
    3. 18 ft
    4. 12 ft Correct answer.

    Explanation

    NEC 230.24(B)(1) sets the minimum clearance above residential driveways and commercial areas not subject to truck traffic at 12 ft. The 10 ft value applies only to sidewalks and areas accessible to pedestrians alone, while 18 ft applies to public streets and areas where truck traffic is expected.

  42. Question 42Services, Feeders, and Branch Circuits

    What is the minimum depth of working space in front of a 480-volt panelboard where the energized parts are exposed on one side and there are no grounded or energized parts on the opposite side?

    1. 2 1/2 ft
    2. 3 1/2 ft
    3. 2 ft
    4. 3 ft Correct answer.

    Explanation

    Table 110.26(A)(1) bases the required depth on the voltage and on the conditions found across the working space. Condition 1, where exposed live parts exist on one side only and no grounded or live parts are on the other, requires 3 ft for equipment rated 600 volts or less.

  43. Question 43Services, Feeders, and Branch Circuits

    Service-drop conductors pass over the roof of a building with a slope of 3/12. What minimum clearance must be maintained above the roof surface?

    1. 3 ft
    2. 4 ft
    3. 8 ft Correct answer.
    4. 6 ft

    Explanation

    Section 230.24(A) requires service-drop conductors to maintain 8 ft of clearance above the roof surface as a general rule. Reduced clearances are allowed only under the specific exceptions, such as roofs steeper than 4/12, so a 3/12 roof keeps the full 8 ft requirement.

  44. Question 44Services, Feeders, and Branch Circuits

    In a dwelling unit, what does the general receptacle spacing rule require along a bedroom wall that is broken by a doorway?

    1. A receptacle outlet must be installed every 12 ft of wall space
    2. A receptacle outlet must be installed within 4 ft of each doorway
    3. No point along the floor line may be more than 12 ft from a receptacle outlet
    4. No point along the floor line may be more than 6 ft from a receptacle outlet Correct answer.

    Explanation

    Section 210.52(A)(1) requires receptacle outlets so that no point along the floor line in any wall space is more than 6 ft, measured horizontally, from an outlet in that space. The wall space itself is measured around corners and includes the 2 ft of wall beside a doorway.

  45. Question 45Services, Feeders, and Branch Circuits

    How many small-appliance branch circuits must be provided for the kitchen, pantry, and dining area receptacles of a dwelling unit?

    1. One 20-ampere circuit
    2. One 15-ampere circuit
    3. Two or more 20-ampere circuits Correct answer.
    4. Two or more 15-ampere circuits

    Explanation

    Section 210.11(C)(1) requires at least two 20-ampere small-appliance branch circuits to supply the receptacle outlets in the kitchen, pantry, breakfast room, and dining room. These circuits may also serve the receptacles in those same areas but must remain 20-ampere circuits.

  46. Question 46Services, Feeders, and Branch Circuits

    Which arrangement satisfies the branch-circuit requirement for bathroom receptacle outlets in a dwelling unit?

    1. A 20-ampere circuit supplying only bathroom receptacle outlets Correct answer.
    2. A 15-ampere circuit supplying both the bathroom receptacles and the hallway receptacles
    3. A 15-ampere circuit dedicated to the bathroom lighting outlets
    4. A 20-ampere circuit shared between the bathroom receptacles and the garage receptacles

    Explanation

    Section 210.11(C)(3) requires at least one 20-ampere branch circuit to supply the bathroom receptacle outlets, and that circuit is not permitted to supply outlets outside the bathroom. A 15-ampere circuit or one that also feeds the garage or hallway would not comply.

  47. Question 47Services, Feeders, and Branch Circuits

    Which branch circuit is permitted to serve the laundry receptacle outlets of a dwelling unit?

    1. A 15-ampere circuit protected by a GFCI circuit breaker
    2. A 15-ampere circuit shared with the dining room receptacles
    3. A 20-ampere circuit supplying only laundry receptacle outlets Correct answer.
    4. A 20-ampere circuit that also supplies the garage receptacles

    Explanation

    Section 210.11(C)(2) requires at least one 20-ampere branch circuit for the laundry receptacle outlet, and that circuit is limited to supplying laundry outlets. Sharing it with dining room or garage receptacles, or reducing it to 15 amperes, does not meet the requirement.

  48. Question 48Services, Feeders, and Branch Circuits

    What is the minimum size copper conductor permitted for a 15-ampere branch circuit supplying general-use receptacles?

    1. 10 AWG copper
    2. 12 AWG copper
    3. 16 AWG copper
    4. 14 AWG copper Correct answer.

    Explanation

    Table 310.16 and 240.4(D) permit 14 AWG copper to be protected at 15 amperes, making it the smallest conductor allowed for a 15-ampere branch circuit. Conductors smaller than 14 AWG are not permitted for this use regardless of the overcurrent device rating.

  49. Question 49Services, Feeders, and Branch Circuits

    What is the minimum rating permitted for the service disconnecting means of a one-family dwelling?

    1. 100 amperes Correct answer.
    2. 60 amperes
    3. 200 amperes
    4. 125 amperes

    Explanation

    Section 230.79(C) requires the service disconnecting means for a one-family dwelling to have a rating of not less than 100 amperes. Higher ratings are common but are selected from the calculated load, not mandated as a minimum.

  50. Question 50Services, Feeders, and Branch Circuits

    Using the standard method, how is the general lighting load of a dwelling unit treated by Table 220.42?

    1. First 3000 VA at 100 percent, with the remainder at 35 percent Correct answer.
    2. First 10,000 VA at 100 percent, with the remainder at 40 percent
    3. First 3000 VA at 100 percent, with the remainder at 40 percent
    4. The entire general lighting load is taken at 100 percent

    Explanation

    Table 220.42 applies a 100 percent demand factor to the first 3000 VA of dwelling general lighting load and a 35 percent factor to the remainder. Applying 100 percent to the entire load would overstate the demand used for service and feeder sizing.

  51. Question 51Services, Feeders, and Branch Circuits

    A feeder tap is made under the 10 ft tap rule of 240.21(B)(1). What minimum ampacity must the tap conductors have relative to the overcurrent device protecting the feeder?

    1. Not less than the rating of the overcurrent device
    2. Not less than one-tenth the rating of the overcurrent device Correct answer.
    3. Not less than one-half the rating of the overcurrent device
    4. Not less than one-third the rating of the overcurrent device

    Explanation

    Section 240.21(B)(1) allows a tap up to 10 ft long whose conductors have an ampacity of at least one-tenth of the rating of the overcurrent device ahead of the tap. Additional conditions limit the tap length and how far the tap conductors may run.

  52. Question 52Services, Feeders, and Branch Circuits

    In a dwelling unit, which of these 125-volt, 15- or 20-ampere receptacle locations requires ground-fault circuit-interrupter protection?

    1. A receptacle in an attached garage Correct answer.
    2. A hard-wired electric range in the kitchen
    3. A ceiling luminaire in a hallway
    4. A receptacle in a bedroom

    Explanation

    Section 210.8(A)(2) requires GFCI protection for all 125-volt, 15- and 20-ampere receptacles installed in garages and accessory buildings in dwelling units. Bedroom receptacles, hallway lighting, and hard-wired appliances are not covered by that garage provision.

  53. Question 53Services, Feeders, and Branch Circuits

    Which circuit requires arc-fault circuit-interrupter protection in a dwelling unit?

    1. A 120-volt, 15-ampere branch circuit supplying bedroom outlets Correct answer.
    2. A feeder supplying a detached garage panelboard
    3. A 20-ampere branch circuit supplying only a bathroom receptacle
    4. A 240-volt branch circuit supplying a central air conditioner

    Explanation

    Section 210.12(A) requires AFCI protection for 120-volt, 15- and 20-ampere branch circuits supplying outlets in dwelling unit rooms such as bedrooms, living rooms, and closets. The requirement applies to branch circuits, not to feeders or to 240-volt equipment circuits.

  54. Question 54Services, Feeders, and Branch Circuits

    A multiwire branch circuit supplies two 120-volt loads from a panelboard. What must be provided at the panelboard for the ungrounded conductors of this circuit?

    1. A means that simultaneously disconnects all ungrounded conductors at the point where the circuit originates Correct answer.
    2. A GFCI receptacle at the first outlet box on the circuit
    3. A neutral conductor sized larger than the ungrounded conductors
    4. A separate overcurrent device for each ungrounded conductor with no tie between them

    Explanation

    Section 210.4(B) requires a device or identified handle tie that disconnects all ungrounded conductors of a multiwire branch circuit at the same time. This prevents the hazard of a circuit remaining energized while a worker believes it has been de-energized.

  55. Question 55Services, Feeders, and Branch Circuits

    When must the ampacity of a conductor be corrected for ambient temperature using the correction factors of Table 310.15(B)(1)?

    1. Whenever the ambient temperature around the conductors exceeds 30 degrees C Correct answer.
    2. Only for feeders sized 1/0 AWG and larger
    3. Never, provided the terminations are rated 75 degrees C
    4. Only when the conductors are installed in a raceway

    Explanation

    Table 310.16 ampacities are based on an ambient temperature of 30 degrees C, so correction is required whenever the surrounding ambient is higher or lower than that base. The correction factors account for how heat dissipation changes with temperature.

  56. Question 56Services, Feeders, and Branch Circuits

    Which statement about counting the neutral as a current-carrying conductor in a raceway is correct?

    1. The neutral is counted as a current-carrying conductor in every case
    2. The neutral is counted as two current-carrying conductors
    3. The neutral is counted only when the circuit supplies nonlinear loads
    4. The neutral of a 4-wire, three-phase wye circuit is not counted as a current-carrying conductor Correct answer.

    Explanation

    Section 310.15(E) permits the neutral of a 4-wire, three-phase wye circuit to be excluded from the current-carrying conductor count when it carries only the unbalanced current of the circuit. Neutrals that carry harmonic currents, such as those serving nonlinear loads, must be counted.

  57. Question 57Services, Feeders, and Branch Circuits

    A 20-ampere branch circuit supplies multiple receptacle outlets in a dwelling unit. Which receptacle ratings are permitted on this circuit?

    1. 15- or 20-ampere receptacles Correct answer.
    2. Receptacles rated not more than 10 amperes
    3. Only 20-ampere receptacles
    4. Only 15-ampere receptacles

    Explanation

    Table 210.21(B)(3) permits 15-ampere and 20-ampere receptacles on a 20-ampere branch circuit when more than one receptacle is supplied. A single receptacle on an individual branch circuit must match the branch-circuit rating.

  58. Question 58Services, Feeders, and Branch Circuits

    According to the informational notes to 210.19(A), what maximum voltage drop is recommended for a branch circuit feeding a load?

    1. 10 percent
    2. 3 percent Correct answer.
    3. 2 percent
    4. 1 percent

    Explanation

    The informational notes to 210.19(A) suggest sizing branch-circuit conductors so the voltage drop does not exceed 3 percent to the farthest outlet. Combined with feeder drop, the total voltage drop is recommended to stay within 5 percent.

  59. Question 59Services, Feeders, and Branch Circuits

    Where must the service disconnecting means for a building be installed?

    1. Anywhere inside the building within 25 ft of the panelboard
    2. Nearest the point of entrance of the service conductors Correct answer.
    3. On the load side of the meter socket only
    4. At the point where the utility attaches its service drop

    Explanation

    Section 230.70(A)(1) requires the service disconnecting means to be installed at a readily accessible location either outside the building or inside nearest the point of entrance of the service conductors. Keeping it near the entry point limits the length of unfused, unprotected service conductors inside the building.

  60. Question 60Services, Feeders, and Branch Circuits

    A one-family dwelling has a 120/240-volt, single-phase service rated 200 amperes. Using the allowable percentage reduction of 310.15(B)(7), what is the minimum size copper service-entrance conductor for the ungrounded conductors?

    1. 4 AWG copper
    2. 3/0 AWG copper
    3. 2/0 AWG copper Correct answer.
    4. 1/0 AWG copper

    Explanation

    Section 310.15(B)(7) permits dwelling service and feeder conductors carrying the entire load to be sized at 83 percent of the service rating, so 200 amperes becomes 166 amperes. A 2/0 AWG copper conductor rated 75 degrees C has an ampacity of 175 amperes, which satisfies the reduced requirement.

  61. Question 61Services, Feeders, and Branch Circuits

    A dwelling unit contains one electric range nameplate-rated 12 kW. What is the demand load for this range under Table 220.55?

    1. 5 kW
    2. 12 kW
    3. 6 kW
    4. 8 kW Correct answer.

    Explanation

    Table 220.55 assigns a demand of 8 kW for a single household electric range rated not over 12 kW. The demand allowance recognizes that ranges seldom draw their full nameplate rating at one time. The kitchen branch circuit and the service calculation both use this demand value.

  62. Question 62Services, Feeders, and Branch Circuits

    A service is supplied by 2/0 AWG copper service-entrance conductors. What is the minimum size copper grounding electrode conductor required by Table 250.66?

    1. 6 AWG copper
    2. 2 AWG copper
    3. 4 AWG copper Correct answer.
    4. 8 AWG copper

    Explanation

    Table 250.66 sizes the grounding electrode conductor by the circular mil area of the largest service-entrance conductor. For 2/0 AWG copper, the table requires a 4 AWG copper grounding electrode conductor.

  63. Question 63Services, Feeders, and Branch Circuits

    A feeder tap is made under the 25 ft tap rule of 240.21(B)(2). What minimum ampacity must the tap conductors have?

    1. One-tenth the rating of the overcurrent device ahead of the tap
    2. One-half the rating of the overcurrent device ahead of the tap
    3. Two-thirds the rating of the overcurrent device ahead of the tap
    4. One-third the rating of the overcurrent device ahead of the tap Correct answer.

    Explanation

    Section 240.21(B)(2) permits taps up to 25 ft long where the tap conductors have an ampacity of at least one-third of the rating of the overcurrent device protecting the feeder. The rule also requires that the tap terminate in a single overcurrent device or a single set of fuses.

  64. Question 64Services, Feeders, and Branch Circuits

    A feeder raceway contains eight current-carrying conductors. What ampacity adjustment factor applies when using Table 310.15(C)(1)?

    1. 50 percent
    2. 45 percent
    3. 70 percent Correct answer.
    4. 80 percent

    Explanation

    Table 310.15(C)(1) applies a 70 percent adjustment to conductors in a raceway or cable containing seven through nine current-carrying conductors. The factor drops as the conductor count increases because heat cannot dissipate as readily.

  65. Question 65Services, Feeders, and Branch Circuits

    What is the maximum permitted distance between receptacle outlets along a dwelling unit kitchen countertop, measured along the counter?

    1. 48 in
    2. 12 in
    3. 36 in
    4. 24 in Correct answer.

    Explanation

    Section 210.52(C) requires countertop receptacle outlets so that no point along the counter wall line is more than 24 in from a receptacle outlet. The rule applies to the countertop spaces served by the required receptacles, and outlets are measured along the counter surface.

  66. Question 66Services, Feeders, and Branch Circuits

    What is the minimum number of 20-ampere small-appliance branch circuits required to supply the kitchen, pantry, dining room, and similar receptacle outlets in a dwelling unit?

    1. Three
    2. One
    3. Four
    4. Two Correct answer.

    Explanation

    NEC 210.11(C)(1) requires at least two 20-ampere small-appliance branch circuits for the kitchen, pantry, dining room, and similar areas in a dwelling unit. These circuits supply receptacle outlets for countertop appliances and similar loads.

  67. Question 67Services, Feeders, and Branch Circuits

    What is the minimum vertical clearance for overhead service-drop conductors above a residential driveway?

    1. 18 ft
    2. 15 ft
    3. 10 ft
    4. 12 ft Correct answer.

    Explanation

    NEC 230.24(B) requires service-drop conductors to have a minimum clearance of 12 feet above residential driveways. Greater clearances apply over public streets and other specified areas.

  68. Question 68Services, Feeders, and Branch Circuits

    In a dwelling unit, what is the maximum permitted distance along a wall from any point to the nearest receptacle outlet in a general living area?

    1. 4 ft
    2. 8 ft
    3. 5 ft
    4. 6 ft Correct answer.

    Explanation

    NEC 210.52(A)(1) requires receptacle outlets so that no point along the floor line in usable wall space is more than 6 feet from a receptacle outlet. This is often called the 6-foot/12-foot rule.

  69. Question 69Services, Feeders, and Branch Circuits

    What is the minimum depth of working space required in front of a 120/240-volt panelboard installed indoors, under ordinary conditions?

    1. 36 in Correct answer.
    2. 30 in
    3. 32 in
    4. 24 in

    Explanation

    NEC 110.26(A)(1) requires a minimum working-space depth of 36 inches in front of electrical equipment operating at 600 volts or less under the usual condition. The space must be clear and extend from the floor to the required height.

  70. Question 70Services, Feeders, and Branch Circuits

    A 100-ampere feeder is installed with copper THWN conductors and terminations rated 75°C. What is the minimum conductor size permitted, before any adjustment or correction factors?

    1. 4 AWG
    2. 1 AWG
    3. 2 AWG
    4. 3 AWG Correct answer.

    Explanation

    At 75°C, 3 AWG copper has an ampacity of 100 amperes, which matches the 100-ampere feeder requirement. The conductor must have an ampacity at least equal to the feeder rating and must be suitable for the termination temperature.

  71. Question 71Services, Feeders, and Branch Circuits

    A feeder supplies a 48-ampere continuous load at 240 volts, single-phase. What minimum conductor ampacity is required before applying any adjustment or correction factors?

    1. 70 A
    2. 80 A
    3. 50 A
    4. 60 A Correct answer.

    Explanation

    NEC 215.2(A)(1) requires feeder conductors to have an ampacity of at least 125 percent of the continuous load plus 100 percent of the noncontinuous load. For a 48-ampere continuous load, the minimum conductor ampacity is 48 × 1.25 = 60 amperes.

  72. Question 72Services, Feeders, and Branch Circuits

    A feeder supplies a 30-ampere continuous load and a 20-ampere noncontinuous load. What is the minimum standard rating of the feeder overcurrent device?

    1. 60 A Correct answer.
    2. 50 A
    3. 70 A
    4. 55 A

    Explanation

    The calculated feeder load is 30 × 1.25 + 20 = 57.5 amperes. The overcurrent device must be sized at least for this calculated load, and the next standard rating that is not less than 57.5 amperes is 60 amperes.

  73. Question 73Services, Feeders, and Branch Circuits

    A 60-ampere feeder circuit requires an equipment grounding conductor run with the feeder conductors. What is the minimum size copper equipment grounding conductor?

    1. 12 AWG copper
    2. 14 AWG copper
    3. 8 AWG copper
    4. 10 AWG copper Correct answer.

    Explanation

    NEC Table 250.122 sizes the equipment grounding conductor according to the rating of the overcurrent device protecting the circuit. For a 60-ampere overcurrent device, the minimum copper equipment grounding conductor is 10 AWG.

  74. Question 74Services, Feeders, and Branch Circuits

    A one-family dwelling has a 120/240-volt, single-phase service rated 200 amperes. Using the dwelling-unit service conductor allowance of Table 310.12, what is the minimum copper service-entrance conductor size?

    1. 4/0 AWG copper
    2. 1/0 AWG copper
    3. 2/0 AWG copper Correct answer.
    4. 3/0 AWG copper

    Explanation

    Table 310.12 permits dwelling-unit service conductors to have an ampacity of at least 83 percent of the service rating. Eighty-three percent of 200 amperes is 166 amperes, and 2/0 AWG copper at 75°C has an ampacity of 175 amperes, so it is the minimum permitted size.

  75. Question 75Services, Feeders, and Branch Circuits

    For a 20-ampere branch circuit supplying general-use receptacle outlets in a dwelling unit, what maximum number of receptacle outlets does the NEC specify?

    1. Twelve
    2. Eight
    3. No maximum is specified Correct answer.
    4. Ten

    Explanation

    The NEC does not establish a general maximum number of receptacle outlets on a 20-ampere branch circuit in a dwelling unit. The circuit must still serve its intended load and comply with the applicable branch-circuit requirements.

  76. Question 76Services, Feeders, and Branch Circuits

    What is the minimum vertical clearance for service-drop conductors above a flat roof that is not subject to the exceptions in NEC 230.24(A)?

    1. 3 ft
    2. 8 ft Correct answer.
    3. 10 ft
    4. 6 ft

    Explanation

    NEC 230.24(A) requires service-drop conductors to be at least 8 feet above the roof surface. The exceptions permit reduced clearances only under specific conditions involving roof slope and raceway protection.

  77. Question 77Services, Feeders, and Branch Circuits

    A 60-ampere feeder to a detached garage is installed with copper THWN conductors and 75°C terminations. What is the minimum conductor size permitted, before adjustment and correction factors?

    1. 4 AWG copper
    2. 10 AWG copper
    3. 8 AWG copper
    4. 6 AWG copper Correct answer.

    Explanation

    At 75°C, 6 AWG copper THWN has an ampacity of 65 amperes, which is at least the 60-ampere feeder rating. The next smaller standard size, 8 AWG copper, has an ampacity of only 50 amperes at 75°C and is not sufficient.

  78. Question 78Services, Feeders, and Branch Circuits

    A 25 kVA continuous single-phase load is supplied by a 240-volt feeder. What is the minimum standard rating of the feeder overcurrent device?

    1. 150 A Correct answer.
    2. 125 A
    3. 175 A
    4. 200 A

    Explanation

    The load current is 25,000 ÷ 240 = 104.2 amperes. For a continuous load, the overcurrent device must be at least 104.2 × 1.25 = 130.2 amperes, so the next standard rating not less than that value is 150 amperes.

  79. Question 79Services, Feeders, and Branch Circuits

    A dwelling unit has four separately controlled fixed appliances rated 1.5 kW, 2 kW, 3 kW, and 4 kW. Using the 75 percent demand allowance of NEC 220.53, what is the calculated demand load for these appliances?

    1. 8.75 kVA
    2. 7.875 kVA Correct answer.
    3. 6.3 kVA
    4. 10.5 kVA

    Explanation

    The connected load is 1.5 + 2 + 3 + 4 = 10.5 kVA. Because there are four or more fixed appliances, NEC 220.53 permits a 75 percent demand factor, giving 10.5 × 0.75 = 7.875 kVA.

  80. Question 80Services, Feeders, and Branch Circuits

    A 100-ampere feeder uses 3 AWG copper THWN conductors with 75°C terminations. The raceway passes through an area with an ambient temperature of 40°C. What is the corrected conductor ampacity?

    1. 100 A
    2. 82 A
    3. 88 A Correct answer.
    4. 94 A

    Explanation

    At 75°C, 3 AWG copper THWN has a base ampacity of 100 amperes. The ambient correction factor for 40°C is 0.88, so the corrected ampacity is 100 × 0.88 = 88 amperes.

  81. Question 81Wiring Methods, Materials, and Raceways

    Where a run of conduit contains bends between two pull points, what is the maximum total amount of bend permitted?

    1. 360 degrees Correct answer.
    2. 270 degrees
    3. 540 degrees
    4. 180 degrees

    Explanation

    The Code limits the bend between pull points to the equivalent of four quarter bends, or 360 degrees total. This limit applies to every recognized raceway type and exists so conductors can be pulled without damage to insulation or excessive tension.

  82. Question 82Wiring Methods, Materials, and Raceways

    How often must Type NM cable be secured to the building structure?

    1. At intervals not exceeding 3 ft and within 6 in. of each box
    2. At intervals not exceeding 6 ft and within 8 in. of each box
    3. At intervals not exceeding 4 1/2 ft and within 12 in. of each box Correct answer.
    4. At intervals not exceeding 8 ft and within 18 in. of each box

    Explanation

    Nonmetallic-sheathed cable must be secured at intervals not exceeding 1.4 m (4 1/2 ft) and within 300 mm (12 in.) of every box or fitting. The short distance to the box keeps strain off terminations.

  83. Question 83Wiring Methods, Materials, and Raceways

    Rigid supports for a straight horizontal run of electrical metallic tubing must be spaced no more than ____ apart.

    1. 10 ft Correct answer.
    2. 12 ft
    3. 5 ft
    4. 6 ft

    Explanation

    EMT must be securely fastened in place at intervals not exceeding 3 m (10 ft) and within 900 mm (3 ft) of each box or fitting. The spacing rule prevents sagging and mechanical damage.

  84. Question 84Wiring Methods, Materials, and Raceways

    When a raceway contains three or more conductors, the conductors may occupy no more than what percentage of the raceway's cross-sectional area?

    1. 31 percent
    2. 53 percent
    3. 40 percent Correct answer.
    4. 60 percent

    Explanation

    The fill tables permit 53 percent for a single conductor, 31 percent for two conductors, and 40 percent for three or more. Keeping the fill at 40 percent leaves room for pulling and heat dissipation.

  85. Question 85Wiring Methods, Materials, and Raceways

    How must a junction box enclosing splices be mounted?

    1. So that it remains accessible without removing any part of the building finish Correct answer.
    2. At least 12 in. above the ceiling line
    3. Flush with the finished surface only
    4. Inside a cabinet that requires a tool to open

    Explanation

    Boxes must remain accessible; the Code prohibits concealing a box so that the wiring inside cannot be reached without damaging the building. A box that requires removal of finish material to reach its cover is a violation.

  86. Question 86Wiring Methods, Materials, and Raceways

    A 120-volt residential branch circuit is buried directly in the earth using Type UF cable. The circuit is not GFCI protected and no other supplemental protection is provided. What is the minimum cover required?

    1. 24 in. Correct answer.
    2. 12 in.
    3. 18 in.
    4. 6 in.

    Explanation

    The burial table requires 24 in. of cover for direct-buried cables in earth. The reduced 12 in. depth applies only to residential 120-volt circuits rated 20 amperes or less that are GFCI protected.

  87. Question 87Wiring Methods, Materials, and Raceways

    What is the smallest trade size of electrical metallic tubing recognized by the Code?

    1. 3/4 in.
    2. 1/2 in. Correct answer.
    3. 1 in.
    4. 3/8 in.

    Explanation

    EMT is manufactured and listed in trade sizes from 1/2 in. through 4 in. Anything smaller is not a recognized EMT size.

  88. Question 88Wiring Methods, Materials, and Raceways

    The interlocked metal armor of Type MC cable is permitted to serve as which of the following?

    1. An ungrounded circuit conductor
    2. The overcurrent protective device
    3. The equipment grounding conductor Correct answer.
    4. The grounded circuit conductor

    Explanation

    The Code lists the armor of Type MC cable as a permitted equipment grounding conductor where the cable is listed for that use and the installation complies with the termination requirements. The armor is never a circuit conductor.

  89. Question 89Wiring Methods, Materials, and Raceways

    Liquidtight flexible metal conduit must be supported within what distance of each box and at what maximum intervals?

    1. Within 6 in. of each box and at intervals not exceeding 3 ft
    2. Within 12 in. of each box and at intervals not exceeding 4 1/2 ft Correct answer.
    3. Within 18 in. of each box and at intervals not exceeding 6 ft
    4. Within 8 in. of each box and at intervals not exceeding 3 ft

    Explanation

    Liquidtight flexible metal conduit must be securely fastened within 300 mm (12 in.) of each box or fitting and supported at intervals not exceeding 1.4 m (4 1/2 ft). The rule keeps the flexible section from being pulled loose from terminations.

  90. Question 90Wiring Methods, Materials, and Raceways

    A run of Schedule 40 PVC conduit is installed outdoors where the ambient temperature varies widely over the year. What must be provided in the run?

    1. Threaded couplings at both ends
    2. Expansion fittings Correct answer.
    3. Additional straps every 12 in.
    4. A larger conduit size

    Explanation

    PVC has a high coefficient of thermal expansion, so expansion fittings must be installed where the conduit is exposed to significant temperature changes. Without them, the conduit can buckle or pull apart at joints.

  91. Question 91Wiring Methods, Materials, and Raceways

    Six current-carrying conductors are installed in a single raceway. What ampacity adjustment factor applies to those conductors?

    1. 80 percent Correct answer.
    2. 70 percent
    3. 50 percent
    4. 100 percent

    Explanation

    The bundling adjustment table applies 80 percent to four, five, or six current-carrying conductors in one raceway or cable. The factor accounts for reduced heat dissipation when conductors are grouped.

  92. Question 92Wiring Methods, Materials, and Raceways

    Each 8 AWG conductor in a box requires how much free space?

    1. 2.00 cu in.
    2. 2.25 cu in.
    3. 3.00 cu in. Correct answer.
    4. 5.00 cu in.

    Explanation

    The box fill table assigns 3.00 cu in. to each 8 AWG conductor. Smaller conductors require 2.00 cu in. for 14 AWG and 2.25 cu in. for 12 AWG, while 6 AWG requires 5.00 cu in.

  93. Question 93Wiring Methods, Materials, and Raceways

    Conductors of size 4 AWG and larger entering a rigid metal conduit must be protected at the conduit end by which of the following?

    1. A listed bushing Correct answer.
    2. A grounding wedge
    3. A locknut
    4. A reducing washer

    Explanation

    Where conductors of 4 AWG or larger enter a raceway, box, or fitting, the Code requires a fitting or listed bushing to protect the conductor insulation from abrasion. The bushing provides a smooth, rounded bearing surface.

  94. Question 94Wiring Methods, Materials, and Raceways

    Where a metal raceway passes through a fire-resistance-rated wall assembly, the annular space around the raceway must be ____.

    1. left open for ventilation
    2. filled loosely with sand
    3. covered with a metal plate on one side
    4. sealed with an approved firestop system Correct answer.

    Explanation

    Penetrations of fire-rated assemblies must be closed with an approved firestop method that restores the fire rating of the assembly. Leaving the opening unsealed would allow fire and smoke to pass through.

  95. Question 95Wiring Methods, Materials, and Raceways

    When Type AC cable is cut for termination, what must be installed at the end of the interlocked armor?

    1. A bonding jumper
    2. An anti-short bushing Correct answer.
    3. A sealing washer
    4. A plastic cable tie

    Explanation

    An anti-short bushing, sometimes called a red head, must be installed between the armor and the conductors to protect the conductor insulation from the cut edge of the armor.

  96. Question 96Wiring Methods, Materials, and Raceways

    A horizontal run of 1 in. Schedule 40 PVC conduit must be supported at intervals not exceeding ____.

    1. 6 ft
    2. 5 ft
    3. 3 ft Correct answer.
    4. 4 ft

    Explanation

    The PVC support table requires supports no more than 3 ft apart for trade sizes 1/2 in. through 1 in. Larger sizes are permitted slightly longer intervals because they are stiffer.

  97. Question 97Wiring Methods, Materials, and Raceways

    A single conductor installed in a raceway is permitted to occupy up to what percentage of the raceway's cross-sectional area?

    1. 31 percent
    2. 53 percent Correct answer.
    3. 40 percent
    4. 45 percent

    Explanation

    A single conductor may fill up to 53 percent of the raceway area, because there is no need to pass other conductors alongside it during the pull. Multiple conductors are limited to 31 or 40 percent.

  98. Question 98Wiring Methods, Materials, and Raceways

    How many 12 AWG THHN copper conductors may be installed in a 1/2 in. electrical metallic tubing?

    1. Six conductors
    2. Seven conductors
    3. Eight conductors
    4. Nine conductors Correct answer.

    Explanation

    The raceway fill table for 1/2 in. EMT lists nine 12 AWG THHN conductors at the permitted 40 percent fill. Using the table avoids the need to compute areas manually.

  99. Question 99Wiring Methods, Materials, and Raceways

    Type NM cable is permitted to be installed in which of the following locations?

    1. Inside the void spaces of a masonry block wall
    2. In a wet location such as an exterior raceway
    3. In a dry stud cavity of a one-family dwelling Correct answer.
    4. In the air-handling plenum of a commercial building

    Explanation

    Nonmetallic-sheathed cable is a dry-location wiring method intended for protected interior spaces such as stud cavities and ceiling joists. It is prohibited in wet locations, in ducts and plenums, and inside masonry block voids.

  100. Question 100Wiring Methods, Materials, and Raceways

    Electrical metallic tubing is installed outdoors in a wet location. Which requirement applies?

    1. Fittings must be listed for use in wet locations Correct answer.
    2. No special fittings are required if the tubing is painted
    3. Expansion fittings must be installed at each support
    4. Dielectric bushings must be installed at every coupling

    Explanation

    EMT is permitted in wet locations where corrosion protection is provided, and all fittings and couplings used there must be listed and identified for wet locations, such as raintight fittings. Ordinary set-screw connectors that are not listed for wet locations are not acceptable.

  101. Question 101Wiring Methods, Materials, and Raceways

    Eight 10 AWG THHN copper conductors are installed in a single raceway at an ambient temperature of 30 degrees C and terminate on terminals rated 75 degrees C. What is the ampacity of each conductor after adjustment?

    1. 28 A Correct answer.
    2. 32 A
    3. 24 A
    4. 35 A

    Explanation

    The 90 degrees C ampacity of 10 AWG THHN is 40 A. With eight current-carrying conductors the adjustment factor is 70 percent, giving 28 A, which is below the 35 A terminal limit for 10 AWG at 75 degrees C, so 28 A governs.

  102. Question 102Wiring Methods, Materials, and Raceways

    A box contains eight 14 AWG insulated conductors, one 14 AWG equipment grounding conductor, and one duplex receptacle. No cable clamps are used. What minimum box volume is required?

    1. 22.0 cu in. Correct answer.
    2. 18.0 cu in.
    3. 20.0 cu in.
    4. 16.0 cu in.

    Explanation

    Each 14 AWG conductor requires 2.00 cu in., so the eight insulated conductors take 16.0 cu in. A single 2.00 cu in. allowance covers all the equipment grounding conductors, and a duplex receptacle counts as two conductors for 4.00 cu in., for a total of 22.0 cu in.

  103. Question 103Wiring Methods, Materials, and Raceways

    A feeder is protected by a 400-ampere overcurrent device and is run in PVC conduit. The copper equipment grounding conductor installed with the feeder must be at least ____.

    1. 4 AWG
    2. 6 AWG
    3. 3 AWG Correct answer.
    4. 1 AWG

    Explanation

    The equipment grounding conductor table sizes the copper conductor by the rating of the overcurrent device protecting the circuit. For a 400-ampere device the minimum copper size is 3 AWG, regardless of the phase conductor size.

  104. Question 104Wiring Methods, Materials, and Raceways

    The conductors of a feeder are paralleled in two separate raceways. What is the minimum permitted size of the paralleled conductors?

    1. 2 AWG copper
    2. 8 AWG copper
    3. 1/0 AWG copper Correct answer.
    4. 4 AWG copper

    Explanation

    Conductors installed in parallel must be 1/0 AWG or larger. The rule exists because smaller conductors do not divide current predictably between parallel paths.

  105. Question 105Wiring Methods, Materials, and Raceways

    In a 3-phase, 4-wire wye circuit, when is the neutral conductor counted as a current-carrying conductor for ampacity adjustment?

    1. When the circuit supplies only line-to-line loads
    2. When the major portion of the load is nonlinear, such as electronic equipment Correct answer.
    3. When the circuit is protected by a GFCI device
    4. When the neutral is smaller than the phase conductors

    Explanation

    The neutral of a 4-wire wye circuit normally carries only the unbalanced current and is not counted. It must be counted when the major portion of the load is nonlinear, because triplen harmonics then add in the neutral instead of cancelling.

  106. Question 106Wiring Methods, Materials, and Raceways

    Between any two pull points, the total degrees of bends in a run of rigid metal conduit shall not exceed ____.

    1. 270 degrees
    2. 360 degrees Correct answer.
    3. 90 degrees
    4. 180 degrees

    Explanation

    Section 344.26 limits a conduit run to the equivalent of four quarter bends, or 360 degrees, between pull points such as boxes and conduit bodies. Exceeding that limit makes conductor pulling difficult and can damage insulation.

  107. Question 107Wiring Methods, Materials, and Raceways

    Electrical metallic tubing shall be securely fastened at intervals not exceeding ____ and within ____ of each box, cabinet, or conduit body.

    1. 12 ft; 5 ft
    2. 10 ft; 3 ft Correct answer.
    3. 6 ft; 12 in.
    4. 5 ft; 3 in.

    Explanation

    Section 358.30(A) requires EMT to be fastened at intervals not exceeding 10 ft and within 3 ft of each box, cabinet, conduit body, or termination. Keeping the support close to the enclosure prevents the tubing from pulling loose or sagging.

  108. Question 108Wiring Methods, Materials, and Raceways

    Splices and taps of conductors shall be permitted to be installed ____.

    1. inside a raceway only where the splice is of the insulation-piercing type
    2. inside a raceway that is at least 1 1/4 in. trade size
    3. at any point along a raceway where the conductors remain accessible
    4. in a box, conduit body, or other approved enclosure Correct answer.

    Explanation

    Section 300.15 requires a box, conduit body, or other approved enclosure at every splice, tap, or termination of conductors. A raceway itself is not an enclosure, so splices may not be made inside it regardless of size or accessibility.

  109. Question 109Wiring Methods, Materials, and Raceways

    Flexible metal conduit shall be supported and secured at intervals not exceeding ____ and within ____ of each box or fitting.

    1. 3 ft; 18 in.
    2. 6 ft; 12 in.
    3. 10 ft; 3 ft
    4. 4.5 ft; 12 in. Correct answer.

    Explanation

    Section 348.30 requires FMC to be supported at intervals not exceeding 4.5 ft and within 12 in. of each box or fitting. The shorter interval is necessary because the flexible conduit can sag between supports.

  110. Question 110Wiring Methods, Materials, and Raceways

    Type NM cable is run across the top of floor joists in an accessible attic. Guard strips are required where the cable is within ____ of the attic access opening.

    1. 12 in.
    2. 4.5 ft
    3. 6 ft Correct answer.
    4. 10 ft

    Explanation

    Section 334.23 requires protection by substantial guard strips, at least as high as the cable, where cable runs across the top of floor joists within 6 ft of the attic scuttle or access opening. This protects the cable from damage by persons entering the attic.

  111. Question 111Wiring Methods, Materials, and Raceways

    PVC conduit is installed exposed on the face of a wall in an area where it is subject to physical damage. The minimum schedule that must be used is ____.

    1. any schedule listed for the application
    2. Schedule 80 Correct answer.
    3. Schedule 20
    4. Schedule 40

    Explanation

    Section 352.10(F) permits rigid nonmetallic conduit in exposed locations but requires Schedule 80 or equivalent where the conduit is subject to physical damage. Schedule 80 has a thicker wall than Schedule 40 and better resists impact.

  112. Question 112Wiring Methods, Materials, and Raceways

    Type MC cable shall be secured and supported at intervals not exceeding ____ and within ____ of each box, fitting, or termination.

    1. 6 ft; 3 ft
    2. 6 ft; 12 in. Correct answer.
    3. 10 ft; 3 ft
    4. 4.5 ft; 12 in.

    Explanation

    Section 330.30 requires Type MC cable to be secured and supported at intervals not exceeding 6 ft and within 12 in. of boxes, fittings, and terminations. The interlocked armor gives the cable enough stiffness to allow a longer interval than flexible conduit.

  113. Question 113Wiring Methods, Materials, and Raceways

    Type NM cable is pulled through a bored hole in a wood stud. A steel plate is required where the hole is less than ____ from the nearest edge of the stud.

    1. 1 in.
    2. 2 in.
    3. 1 1/4 in. Correct answer.
    4. 3/4 in.

    Explanation

    Section 300.4(A)(1) requires steel plates at least 1/16 in. thick where cable passes through a bored hole less than 1 1/4 in. from the nearest edge of a wood framing member. The plate protects the cable from damage by nails and screws driven into the stud.

  114. Question 114Wiring Methods, Materials, and Raceways

    Rigid metal conduit used as a direct-burial wiring method for a branch circuit must have a minimum cover of ____.

    1. 24 in.
    2. 18 in.
    3. 6 in. Correct answer.
    4. 12 in.

    Explanation

    Table 300.5 permits rigid metal conduit and intermediate metal conduit to be buried with only 6 in. of cover, measured from the top of the conduit to finished grade. Nonmetallic raceways require 18 in. and Type UF cable generally requires 24 in.

  115. Question 115Wiring Methods, Materials, and Raceways

    A 480-volt motor circuit and a 120-volt lighting circuit are run in the same rigid metal conduit. This installation is permitted if ____.

    1. the conduit is bonded at both ends
    2. every conductor is insulated for the highest voltage in the raceway Correct answer.
    3. the conduit is at least 1 1/4 in. trade size
    4. the 120-volt conductors are installed in a separate innerduct

    Explanation

    Section 300.3(C)(1) permits conductors of different systems to occupy the same raceway where all conductors are insulated for the maximum voltage of any conductor in that raceway. The raceway must also be suitable for the highest voltage present.

  116. Question 116Wiring Methods, Materials, and Raceways

    A grounding electrode conductor is installed in a ferrous metal raceway. The raceway shall be ____.

    1. bonded to the conductor only at the service equipment
    2. electrically continuous and bonded to the conductor at each end Correct answer.
    3. sized no smaller than the grounding electrode conductor
    4. isolated from the conductor by an insulating bushing at each end

    Explanation

    Section 250.64(E) requires a ferrous raceway enclosing a grounding electrode conductor to be electrically continuous and bonded to the conductor at both ends. Bonding at each end prevents the raceway's inductive reactance from degrading the fault-current path.

  117. Question 117Wiring Methods, Materials, and Raceways

    Which wiring method is permitted in the space above a suspended ceiling that is used to return air to the air-handling unit?

    1. Electrical nonmetallic tubing
    2. Electrical metallic tubing Correct answer.
    3. Rigid PVC conduit
    4. Type NM cable

    Explanation

    Section 300.22(C) restricts wiring in spaces used for environmental air to metal raceways, metal-sheathed cables, and other wiring methods specifically listed for the purpose. Nonmetallic methods add fuel and smoke to the air stream and are not permitted there.

  118. Question 118Wiring Methods, Materials, and Raceways

    A rigid metal conduit enters a Class I, Division 1 enclosure containing a switch. A sealing fitting must be installed within what maximum distance of the enclosure?

    1. 5 ft
    2. 18 in. Correct answer.
    3. 36 in.
    4. 10 ft

    Explanation

    Section 501.15(A)(1) requires a sealing fitting in each conduit run entering a Class I, Division 1 enclosure, installed as close as practicable and within 18 in. of the enclosure. The seal keeps gases and vapors from passing through the raceway into unclassified areas.

  119. Question 119Wiring Methods, Materials, and Raceways

    Which condition must be met before flexible metal conduit may serve as the equipment grounding conductor for a 20-ampere branch circuit?

    1. A separate green grounding conductor is pulled inside the conduit.
    2. The run is 6 ft or less and the fittings are listed for grounding. Correct answer.
    3. The conduit is supported at intervals not exceeding 4.5 ft.
    4. The conduit is at least 3/4 in. trade size and bonded at one end.

    Explanation

    Section 250.118(5) permits FMC as an equipment grounding conductor only where the circuit conductors are protected at 20 A or less, the total conduit length in any ground-return path is 6 ft or less, and the conduit is terminated with fittings listed for grounding. Longer runs require a separate equipment grounding conductor.

  120. Question 120Wiring Methods, Materials, and Raceways

    A 10 AWG copper conductor with 90 degrees C insulation is installed in Type NM cable for a branch circuit. Its ampacity shall be determined from which temperature column?

    1. The 60 degrees C column, because the cable is Type NM Correct answer.
    2. The 60 degrees C column only where the ambient exceeds 30 degrees C
    3. The 90 degrees C column, because the insulation is rated 90 degrees C
    4. The 75 degrees C column, because the terminals are rated 75 degrees C

    Explanation

    Section 334.80 limits the ampacity of conductors in Type NM cable to the 60 degrees C values in Table 310.16, even where the individual conductors are 90 degrees C rated. The 90 degrees C rating may still be used for ampacity adjustment and correction.

  121. Question 121Equipment, Devices, and Utilization Equipment

    Motor branch-circuit conductors and short-circuit protective devices are sized using the motor full-load current taken from which source?

    1. The overload relay's marked trip rating
    2. The manufacturer's published data sheet
    3. The motor nameplate full-load current
    4. The tables in Article 430 Correct answer.

    Explanation

    Section 430.6(A)(1) requires the full-load current values in Tables 430.248, 430.249, and 430.250 to be used for sizing motor branch-circuit conductors and short-circuit protective devices. Nameplate current is used only for sizing overload protection.

  122. Question 122Equipment, Devices, and Utilization Equipment

    A motor with a marked service factor of 1.15 has a nameplate full-load current of 24 A. The overload device is normally selected so that it will carry, at most, what current?

    1. 24 A
    2. 36 A
    3. 40 A
    4. 30 A Correct answer.

    Explanation

    Section 430.32(A)(1) limits the overload device to 125 percent of the motor nameplate full-load current for a motor with a service factor of 1.15 or greater or a temperature rise of 40 degrees C or less. Here 24 A times 1.25 equals 30 A.

  123. Question 123Equipment, Devices, and Utilization Equipment

    In a dwelling unit, which bathroom receptacles require ground-fault circuit-interrupter protection?

    1. Only those not already GFCI protected by a breaker
    2. Only those within 6 ft of the sink
    3. Only those serving countertop appliances
    4. All 125-volt, 15- and 20-ampere receptacles Correct answer.

    Explanation

    Section 210.8(A)(1) requires GFCI protection for all 125-volt, single-phase, 15- and 20-ampere receptacle outlets installed in the bathrooms of dwelling units. There is no distance limitation and no exception for receptacles already protected upstream.

  124. Question 124Equipment, Devices, and Utilization Equipment

    Tamper-resistant receptacles are required to be installed in which location?

    1. A dwelling unit Correct answer.
    2. A commercial office break room
    3. A parking garage at a shopping center
    4. An industrial maintenance shop

    Explanation

    Section 406.12 requires tamper-resistant receptacles for 125-volt, 15- and 20-ampere receptacles installed in dwelling units. The requirement is tied to dwelling units rather than to commercial or industrial occupancies.

  125. Question 125Equipment, Devices, and Utilization Equipment

    For the purpose of motor disconnecting means, equipment is considered within sight of the motor where it is visible and located not more than what distance away?

    1. 50 ft Correct answer.
    2. 100 ft
    3. 25 ft
    4. 75 ft

    Explanation

    Article 100 defines within sight (in sight from) as visible and not more than 50 ft from the specified equipment. Motor disconnecting means must generally be within sight of the motor and the driven machinery.

  126. Question 126Equipment, Devices, and Utilization Equipment

    Along a dwelling unit kitchen countertop wall line, receptacle outlets must be installed so that no point along the wall line is more than what distance from a receptacle outlet?

    1. 24 in Correct answer.
    2. 48 in
    3. 12 in
    4. 36 in

    Explanation

    Section 210.52(C)(1) requires countertop receptacle outlets to be arranged so that no point along the wall line is more than 24 in measured horizontally from a receptacle outlet. This provides reasonable access without requiring an excessive number of outlets.

  127. Question 127Equipment, Devices, and Utilization Equipment

    In a dwelling unit, arc-fault circuit-interrupter protection is required for branch circuits supplying outlets in which of these areas?

    1. A bedroom Correct answer.
    2. A garage
    3. A kitchen
    4. A bathroom

    Explanation

    Section 210.12(A) lists the dwelling unit areas requiring AFCI protection, and bedrooms are among the listed rooms. Bathrooms, garages, and kitchens are not included in that list.

  128. Question 128Equipment, Devices, and Utilization Equipment

    Electrical equipment must be selected and applied so that its short-circuit current rating does which of the following?

    1. Exceeds the ampacity of the supply conductors
    2. Is not less than the available fault current Correct answer.
    3. Matches the rating of the branch-circuit breaker
    4. Equals the interrupting rating of the main breaker

    Explanation

    Section 110.10 requires equipment to have a short-circuit current rating at least equal to the fault current available at its terminals. If the available fault current exceeds the equipment rating, the equipment may fail catastrophically.

  129. Question 129Equipment, Devices, and Utilization Equipment

    A 10-hp, 460-volt, three-phase motor has a full-load current of 14 A from Table 430.250. What is the largest standard inverse-time circuit breaker rating permitted for branch-circuit short-circuit and ground-fault protection?

    1. 50 A
    2. 40 A
    3. 35 A Correct answer.
    4. 30 A

    Explanation

    Table 430.52 permits an inverse-time circuit breaker set at not more than 250 percent of the motor full-load current. Here 14 A times 2.50 equals 35 A, which is also a standard rating.

  130. Question 130Equipment, Devices, and Utilization Equipment

    A general-use switch is used as the controller for a stationary 2-hp motor. Its ampere rating must be at least what multiple of the motor full-load current?

    1. Not less than 2 times the full-load current Correct answer.
    2. Not less than the full-load current
    3. Not less than 1.5 times the full-load current
    4. Not less than 2.5 times the full-load current

    Explanation

    Section 430.83(C) permits a general-use switch to serve as the controller for a stationary motor of 2 hp or less where the switch has an ampere rating of at least twice the motor full-load current.

  131. Question 131Equipment, Devices, and Utilization Equipment

    A 230-volt, single-phase motor has a full-load current of 20 A. The motor disconnecting means must have an ampere rating of at least what value?

    1. 20 A
    2. 30 A
    3. 23 A Correct answer.
    4. 22 A

    Explanation

    Section 430.110(A) requires the motor disconnecting means to have an ampere rating of at least 115 percent of the motor full-load current. Here 20 A times 1.15 equals 23 A.

  132. Question 132Equipment, Devices, and Utilization Equipment

    A hermetic refrigerant motor-compressor has a rated-load current of 16 A. What is the maximum rating of the branch-circuit short-circuit and ground-fault protective device that may be used where it will carry the starting current?

    1. 24 A
    2. 22 A
    3. 20 A
    4. 28 A Correct answer.

    Explanation

    Section 440.22(A) permits the branch-circuit protective device to be rated at not more than 175 percent of the motor-compressor rated-load current. Here 16 A times 1.75 equals 28 A.

  133. Question 133Equipment, Devices, and Utilization Equipment

    A 45-kVA, single-phase transformer is supplied at 480 volts. Using the primary-only protection rule, what is the largest standard rating of primary overcurrent device permitted?

    1. 110 A
    2. 150 A
    3. 125 A Correct answer.
    4. 100 A

    Explanation

    The primary current is 45,000 VA divided by 480 V, or 93.75 A, and Table 450.3(B) permits primary-only protection at not more than 125 percent of that value, which is 117.2 A. Where that value is not a standard rating, the next higher standard rating of 125 A is permitted.

  134. Question 134Equipment, Devices, and Utilization Equipment

    A plug-on circuit breaker installed in a panelboard and back-fed from field-installed conductors must be what?

    1. Secured by an additional fastener Correct answer.
    2. Marked suitable for back-feed
    3. Rated for 100 percent duty
    4. Replaced by a bolt-on breaker

    Explanation

    Section 408.36 requires a plug-in circuit breaker that is back-fed from field-installed conductors to be secured by an additional approved fastener so it cannot be removed without the use of tools. The added fastener keeps the breaker from being pulled off the bus under load.

  135. Question 135Equipment, Devices, and Utilization Equipment

    The small-appliance receptacle outlets in a dwelling unit kitchen must be supplied by how many branch circuits?

    1. At least three 15-ampere circuits
    2. At least two 20-ampere circuits Correct answer.
    3. At least one 20-ampere circuit
    4. At least one 15-ampere circuit

    Explanation

    Section 210.52(B)(1) requires at least two 20-ampere small-appliance branch circuits to supply the receptacle outlets in the kitchen, pantry, breakfast room, and dining room. The circuits may also serve other specified outlets but not lighting.

  136. Question 136Equipment, Devices, and Utilization Equipment

    Receptacle outlets serving a dwelling unit kitchen countertop must be located not more than what distance above the countertop?

    1. 12 in
    2. 20 in Correct answer.
    3. 18 in
    4. 15 in

    Explanation

    Section 210.52(C)(5) permits countertop receptacle outlets to be installed on or above the countertop but not more than 20 in above it. A receptacle higher than that would not qualify as serving the countertop.

  137. Question 137Equipment, Devices, and Utilization Equipment

    A permanently connected 4.5-kW, 240-volt water heater is fed from a panelboard 30 ft away that is not within sight of the heater. How may the disconnecting means requirement be met?

    1. Rely on the panelboard main as the disconnect
    2. Use a breaker that can be locked open Correct answer.
    3. Install a second equipment grounding conductor
    4. Add a cord-and-plug connection at the heater

    Explanation

    Section 422.31(B) permits the branch-circuit switch or circuit breaker to serve as the disconnecting means for a permanently connected appliance rated over 300 VA where it is within sight of the appliance or is capable of being locked in the open position. A lockable breaker satisfies the rule at a remote panelboard.

  138. Question 138Equipment, Devices, and Utilization Equipment

    A fixed electric space heater draws 16 A. What is the minimum ampacity of the branch-circuit conductors?

    1. 16 A
    2. 32 A
    3. 20 A Correct answer.
    4. 24 A

    Explanation

    Section 424.3(B) requires branch circuits supplying fixed electric space-heating equipment to be sized as continuous loads at 125 percent. Here 16 A times 1.25 equals 20 A.

  139. Question 139Equipment, Devices, and Utilization Equipment

    Which of the following is a permitted use of flexible cord?

    1. Connecting a portable appliance to a receptacle Correct answer.
    2. Replacing permanent wiring inside a wall
    3. Wiring a receptacle above a dropped ceiling
    4. Feeding a junction box from a panelboard

    Explanation

    Section 400.10 permits flexible cord for connection of portable and mobile appliances to a receptacle outlet, among other specific uses. Section 400.12 prohibits using cord as a substitute for fixed wiring of a structure.

  140. Question 140Equipment, Devices, and Utilization Equipment

    Which cover is required for a 15-ampere, 125-volt receptacle installed outdoors on a dwelling unit wall in a wet location?

    1. A blank cover plate
    2. No cover, if the receptacle is listed as weatherproof
    3. A self-closing gasketed cover
    4. A while-in-use cover Correct answer.

    Explanation

    Section 406.9(B)(1) requires an enclosure for wet-location receptacles that maintains weatherproof integrity whether or not an attachment plug is inserted. A while-in-use cover is the type that meets this requirement.

  141. Question 141Equipment, Devices, and Utilization Equipment

    A feeder supplies one 10-hp motor with a full-load current of 14 A and two 5-hp motors with full-load currents of 7.6 A each, all 460-volt three-phase. What minimum feeder conductor ampacity is required?

    1. 36.5 A
    2. 43.2 A
    3. 29.2 A
    4. 32.7 A Correct answer.

    Explanation

    Section 430.24 requires feeder conductors to have an ampacity of 125 percent of the largest motor full-load current plus 100 percent of the other motor currents. That is 17.5 A plus 7.6 A plus 7.6 A, or 32.7 A.

  142. Question 142Equipment, Devices, and Utilization Equipment

    A hermetic motor-compressor has a rated-load current of 20 A and a branch-circuit selection current of 22 A. What is the minimum ampacity of the branch-circuit conductors?

    1. 30.0 A
    2. 27.5 A Correct answer.
    3. 25.0 A
    4. 33.0 A

    Explanation

    Section 440.32 requires branch-circuit conductors to have an ampacity of at least 125 percent of the greater of the rated-load current or the branch-circuit selection current. The selection current of 22 A governs, and 22 A times 1.25 equals 27.5 A.

  143. Question 143Equipment, Devices, and Utilization Equipment

    A motor with a service factor of 1.15 will not start with overload protection sized at 125 percent of its nameplate current. What is the maximum permissible increase in the overload device rating?

    1. 175 percent
    2. 125 percent
    3. 135 percent
    4. 140 percent Correct answer.

    Explanation

    Section 430.32(A)(2) permits the overload device to be increased where 125 percent will not permit the motor to start, but the rating may not exceed 140 percent of the motor nameplate full-load current.

  144. Question 144Equipment, Devices, and Utilization Equipment

    A solidly grounded 480Y/277-volt service has a 1200-ampere service disconnect. Where ground-fault protection of equipment is required, what is the maximum permitted pickup setting?

    1. 1200 A Correct answer.
    2. 600 A
    3. 1000 A
    4. 800 A

    Explanation

    Section 230.95 requires ground-fault protection of equipment for solidly grounded wye services over 150 volts to ground with a service disconnect rated 1000 A or more. The maximum setting is 1200 A with a maximum time delay of 1 second.

  145. Question 145Equipment, Devices, and Utilization Equipment

    For a single motor branch circuit, the 125 percent factor applied to the motor full-load current is determined in what way?

    1. After applying adjustment or correction factors
    2. Using the motor controller's marked ampacity
    3. Using the motor nameplate full-load current
    4. Before applying adjustment or correction factors Correct answer.

    Explanation

    Section 430.22(A) states that the required ampacity of 125 percent of the motor full-load current is established before any ampacity adjustment or correction factors are applied. The adjusted conductor ampacity must still be at least that required value.

  146. Question 146Equipment, Devices, and Utilization Equipment

    In a dwelling unit, general wall-space receptacle outlets must be installed so that no point along the floor line of a wall space is more than what horizontal distance from a receptacle outlet?

    1. 6 ft Correct answer.
    2. 12 ft
    3. 8 ft
    4. 4 ft

    Explanation

    Section 210.52(A)(1) requires receptacle outlets in general wall spaces so that no point measured horizontally along the floor line is more than 6 ft from a receptacle. This produces the familiar maximum spacing of 12 ft between receptacles.

  147. Question 147Equipment, Devices, and Utilization Equipment

    Receptacle outlets installed in a dwelling unit bathroom must be provided with which of the following?

    1. Equipment ground-fault protection
    2. Arc-fault circuit-interrupter protection
    3. Ground-fault circuit-interrupter protection Correct answer.
    4. Surge protective device protection

    Explanation

    Section 210.8(A)(1) requires all 125-volt, 15- and 20-ampere receptacles installed in dwelling unit bathrooms to have ground-fault circuit-interrupter protection. The requirement is based on the location of the receptacle, not on the equipment that is plugged in.

  148. Question 148Equipment, Devices, and Utilization Equipment

    A one-family dwelling is required to have outdoor receptacle outlets installed at which of the following locations?

    1. Only at the back of the dwelling
    2. At the front and at the back of the dwelling Correct answer.
    3. At the front only where a driveway is present
    4. At every exterior door that opens to grade

    Explanation

    Section 210.52(E)(1) requires at least one receptacle outlet accessible at grade level at the front and at the back of a one-family dwelling. The outlets must be not more than 6.5 ft above grade.

  149. Question 149Equipment, Devices, and Utilization Equipment

    A surface-mounted incandescent luminaire with a completely enclosed light source is installed in a clothes closet. It must be located at least what minimum distance from the nearest point of the storage area?

    1. 12 in. Correct answer.
    2. 18 in.
    3. 24 in.
    4. 6 in.

    Explanation

    Table 410.16(C) sets the minimum clearance between storage areas and closet luminaires. For a surface-mounted incandescent luminaire with a completely enclosed light source, the required clearance is 12 in.

  150. Question 150Equipment, Devices, and Utilization Equipment

    A dishwasher is permitted to be connected by a flexible cord and plug. The flexible cord must be what length?

    1. 3 ft to 4 ft Correct answer.
    2. Not more than 6 ft, of any length
    3. 1 ft to 3 ft
    4. 4 ft to 6 ft

    Explanation

    Section 422.16(B)(1) permits a dishwasher to be cord-and-plug connected where the receptacle is located in the cabinet space adjacent to the appliance and is accessible after installation. The cord must be not less than 3 ft and not more than 4 ft long.

  151. Question 151Equipment, Devices, and Utilization Equipment

    The disconnecting means for a motor must be located within sight from and readily accessible from the motor. Where this is not practicable, the disconnecting means shall be which of the following?

    1. Marked as the motor disconnecting means
    2. Capable of being locked in the open position Correct answer.
    3. Located not more than 50 ft from the motor
    4. Installed on the controller enclosure

    Explanation

    Section 430.102(B) requires the motor disconnecting means to be within sight from and readily accessible from the motor. The exception permits the disconnect to be located elsewhere if it is capable of being locked in the open position, so the motor cannot be energized while persons work on it.

  152. Question 152Equipment, Devices, and Utilization Equipment

    A hermetic refrigerant motor-compressor has a rated-load current of 20 A and a branch-circuit selection current of 24 A. What is the minimum ampacity of the branch-circuit conductors supplying the compressor?

    1. 24 A
    2. 30 A Correct answer.
    3. 25 A
    4. 36 A

    Explanation

    Section 440.32 requires branch-circuit conductors to have an ampacity of not less than 125 percent of the larger of the rated-load current or the branch-circuit selection current. Using 24 A, the calculation is 24 A x 1.25 = 30 A.

  153. Question 153Equipment, Devices, and Utilization Equipment

    A transformer rated 1000 volts or less is installed indoors. Its primary disconnecting means must be which of the following?

    1. Not more than 25 ft from the transformer
    2. Within sight from the transformer or capable of being locked open Correct answer.
    3. Accessible only to qualified persons and marked with the primary voltage
    4. Installed ahead of the transformer overcurrent device in the primary circuit

    Explanation

    Section 450.14 requires a disconnecting means in the transformer primary circuit that is installed within sight from the transformer. Where that location is not practicable, the disconnecting means must be capable of being locked in the open position.

  154. Question 154Equipment, Devices, and Utilization Equipment

    A 15-ampere, 125-volt grounding-type receptacle is being replaced at an outlet where no equipment grounding conductor is present in the box. Which of the following is a permitted method of replacement?

    1. Bond the receptacle yoke to a nearby metal raceway
    2. Connect the grounding terminal of the receptacle to the grounded conductor
    3. Install a grounding-type receptacle with a self-grounding clip
    4. Install a ground-fault circuit-interrupter receptacle Correct answer.

    Explanation

    Section 406.4(D)(2) permits a grounding-type receptacle to be installed at such an outlet only where it is provided with ground-fault circuit-interrupter protection, is fed through a GFCI receptacle upstream, or is a listed GFCI-type receptacle. The equipment grounding conductor may never be connected to the neutral.

  155. Question 155Equipment, Devices, and Utilization Equipment

    A receptacle outlet installed at a permanently installed swimming pool must be located not less than what distance from the inside wall of the pool?

    1. 10 ft
    2. 6 ft Correct answer.
    3. 3 ft
    4. 5 ft

    Explanation

    Section 680.22(A)(1) requires receptacle outlets for pool-related equipment and other outlets to be not less than 6 ft from the inside walls of a permanently installed pool, unless the outlet is for a specific listed purpose permitted by the article. The distance is measured from the pool wall, not from the water's edge of a portable pool.

  156. Question 156Equipment, Devices, and Utilization Equipment

    A 4.5-kW, 240-volt storage-type water heater with a 50-gallon tank is supplied by a branch circuit. What is the minimum ampacity of the branch-circuit conductors?

    1. 23.4 A Correct answer.
    2. 30.0 A
    3. 18.8 A
    4. 25.0 A

    Explanation

    Section 422.13 treats a storage-type water heater with a capacity of 120 gallons or less as a continuous load. The heater draws 4500 VA / 240 V = 18.75 A, and 125 percent of that value is 23.4 A.

  157. Question 157Equipment, Devices, and Utilization Equipment

    A panelboard must be protected against overcurrent in accordance with its rating. This protection must be provided on which side of the panelboard?

    1. Only where the panelboard is back-fed
    2. On the supply side of the panelboard Correct answer.
    3. At each branch-circuit breaker in the panelboard
    4. On the load side of the panelboard

    Explanation

    Section 408.36 requires each panelboard to be protected by an overcurrent protective device with a rating not greater than that of the panelboard, and that protection must be on the supply side. This prevents the panelboard bus from being subjected to current above its rating.

  158. Question 158Equipment, Devices, and Utilization Equipment

    A 25-hp, 480-volt, three-phase design B energy-efficient motor has a full-load current of 34 A. The standard inverse-time circuit breaker selected from Table 430.52 will not carry the starting current. What is the maximum rating of breaker that may be used?

    1. 102 A Correct answer.
    2. 136 A
    3. 85 A
    4. 120 A

    Explanation

    Table 430.52 permits an inverse-time circuit breaker at 250 percent of full-load current, which is 85 A here, and Exception No. 2 permits the rating to be increased where starting current is insufficient. For a design B energy-efficient motor the increased rating may not exceed 300 percent of 34 A, or 102 A.

  159. Question 159Equipment, Devices, and Utilization Equipment

    In a Class I, Division 1 location, a conduit containing insulated conductors enters an explosionproof enclosure that houses arcing contacts. A conduit seal must be installed within what maximum distance of the enclosure?

    1. 6 in.
    2. 18 in. Correct answer.
    3. 24 in.
    4. 12 in.

    Explanation

    Section 501.15(A)(1)(1) requires a seal in each conduit run entering an explosionproof enclosure that contains arcing devices, and the seal must be located within 18 in. of the enclosure. The seal limits the passage of gases and prevents pressure piling between enclosures.

  160. Question 160Equipment, Devices, and Utilization Equipment

    An arc welder has a primary current rating of 40 A at a 60-percent duty cycle. What is the minimum ampacity of the branch-circuit conductors supplying the welder?

    1. 40.0 A
    2. 50.0 A
    3. 24.0 A
    4. 31.2 A Correct answer.

    Explanation

    Section 630.11(A) sizes arc welder branch-circuit conductors by multiplying the rated primary current by the duty-cycle multiplier in Table 630.11(A). The multiplier for a 60-percent duty cycle is 0.78, so 40 A x 0.78 = 31.2 A.

  161. Question 161Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A service is supplied by 3/0 AWG copper ungrounded service-entrance conductors. What is the minimum size copper grounding electrode conductor permitted by Table 250.66?

    1. 1/0 AWG
    2. 2 AWG
    3. 6 AWG
    4. 4 AWG Correct answer.

    Explanation

    Table 250.66 sizes the grounding electrode conductor by the largest ungrounded service conductor. For 3/0 AWG copper, the table requires 4 AWG copper.

  162. Question 162Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A rod-type grounding electrode must have a minimum length of ___ unless listed otherwise.

    1. 10 ft
    2. 8 ft Correct answer.
    3. 12 ft
    4. 6 ft

    Explanation

    Section 250.52(A)(5) requires rod electrodes to be at least 8 ft long and listed, unless a longer rod is specified.

  163. Question 163Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A single ground rod measures 25 ohms to ground. What does the NEC require?

    1. Add a second rod 6 ft away. Correct answer.
    2. No further action is required.
    3. Install a concrete-encased electrode.
    4. Replace the rod with a 10 ft rod.

    Explanation

    Section 250.53(A)(2) permits a single rod if it measures 25 ohms or less. If resistance exceeds 25 ohms, one additional electrode must be installed at least 6 ft away.

  164. Question 164Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which of the following is a standard ampere rating for an overcurrent device in 240.6(A)?

    1. 75 A
    2. 55 A
    3. 90 A Correct answer.
    4. 130 A

    Explanation

    Section 240.6(A) lists standard ampere ratings, which include 90 A. Ratings such as 55 A, 75 A, and 130 A are not standard.

  165. Question 165Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A 200-ampere branch circuit is protected by a circuit breaker. What minimum size copper equipment grounding conductor is required by Table 250.122?

    1. 8 AWG copper
    2. 4 AWG copper
    3. 10 AWG copper
    4. 6 AWG copper Correct answer.

    Explanation

    Table 250.122 sets the equipment grounding conductor by the rating of the overcurrent device. A 200-ampere device requires 6 AWG copper.

  166. Question 166Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Where is the main bonding jumper installed in a typical service?

    1. At each panelboard
    2. In the service equipment Correct answer.
    3. At the grounding electrode
    4. At the meter socket

    Explanation

    The main bonding jumper connects the grounded service conductor to the equipment grounding conductor. It is installed in the service equipment, not at downstream panels.

  167. Question 167Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A bonding jumper is installed around a water meter in a metal water piping system. How is the jumper sized?

    1. Table 250.102(C)(1) using the service conductor size Correct answer.
    2. Table 250.66 using the grounding electrode conductor
    3. Table 250.122 using the panelboard rating
    4. Table 310.16 using the water pipe size

    Explanation

    Section 250.104(A) requires metal water piping to be bonded, and jumpers around meters or insulated fittings are sized by Table 250.102(C)(1) using the service conductors.

  168. Question 168Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which receptacle requires GFCI protection in a dwelling unit?

    1. A 125-volt refrigerator receptacle
    2. A 125-volt bedroom receptacle
    3. A 20-ampere garage receptacle Correct answer.
    4. A 240-volt dryer receptacle

    Explanation

    GFCI protection is required for 15- and 20-ampere, 125-volt receptacles in garages, outdoors, bathrooms, and similar locations. A 20-ampere garage receptacle falls within that requirement.

  169. Question 169Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    AFCI protection is required for which dwelling-unit branch circuits?

    1. Bathroom branch circuits
    2. Garage branch circuits
    3. Bedroom branch circuits Correct answer.
    4. Outdoor branch circuits

    Explanation

    AFCI protection is required for 120-volt, 15- and 20-ampere branch circuits supplying outlets in dwelling units, including bedrooms. Bathrooms, garages, and outdoor circuits are generally excluded.

  170. Question 170Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Under the 10-ft tap rule, what minimum ampacity must the tap conductors have relative to the overcurrent device protecting the feeder?

    1. At least 1/10 of the overcurrent device rating Correct answer.
    2. At least 1/3 of the overcurrent device rating
    3. At least 1/2 of the overcurrent device rating
    4. At least the full overcurrent device rating

    Explanation

    The 10-ft tap rule in 240.21(B)(1) requires tap conductors with ampacity at least one-tenth of the overcurrent device rating. The tap must also be protected from physical damage and terminate in an overcurrent device.

  171. Question 171Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A conductor has an ampacity of 85 A and is not part of a multioutlet receptacle circuit. What is the maximum standard overcurrent device rating permitted by 240.4(B)?

    1. 85 A
    2. 90 A Correct answer.
    3. 80 A
    4. 100 A

    Explanation

    Section 240.4(B) permits the next higher standard rating if the conductor ampacity does not match a standard size, the rating does not exceed 800 A, and the circuit is not a multioutlet receptacle circuit. For 85 A, the next standard size is 90 A.

  172. Question 172Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which device provides short-circuit and ground-fault protection for a motor branch circuit?

    1. The motor overload relay protecting the motor
    2. The branch-circuit protective device Correct answer.
    3. The disconnecting means at the motor
    4. The thermal protector built into the motor

    Explanation

    The branch-circuit protective device clears short circuits and ground faults. Motor overload protection is provided separately by overload relays or thermal protectors.

  173. Question 173Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A location where flammable vapors are present only under abnormal operating conditions is classified as:

    1. Class II, Division 1
    2. Class III, Division 2
    3. Class I, Division 1
    4. Class I, Division 2 Correct answer.

    Explanation

    Class I locations involve flammable gases or vapors. Division 2 covers conditions where the hazard is present only under abnormal operation.

  174. Question 174Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    In a Class I, Division 1 location, a conduit seal must be installed within what distance of an explosionproof enclosure?

    1. Within 5 feet
    2. Within 6 inches
    3. Within 18 inches Correct answer.
    4. Within 36 inches

    Explanation

    Section 501.15(A)(1) requires a seal within 18 inches of an explosionproof enclosure in a Class I, Division 1 location. The seal limits passage of gases through the conduit.

  175. Question 175Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Receptacles in patient care areas of a health care facility must be listed as:

    1. Hospital-grade Correct answer.
    2. Isolated-ground
    3. Weather-resistant
    4. Tamper-resistant

    Explanation

    Section 517.18 requires receptacles in patient care areas to be listed as hospital grade. These receptacles have a more secure grounding contact.

  176. Question 176Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    An isolated power system in a health care facility operating room is best described as:

    1. A solidly grounded system protected by a GFCI
    2. Ungrounded system with isolation monitor Correct answer.
    3. A high-resistance grounded system with a GFCI
    4. A corner-grounded delta system with a GFCI

    Explanation

    An isolated power system is ungrounded and monitored by a line isolation monitor. The monitor alarms if leakage current reaches a selected level.

  177. Question 177Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    The service disconnecting means must be installed at a readily accessible location that is:

    1. At the point farthest from the service conductors
    2. At the load end of the overhead service drop
    3. Nearest the service conductor entry point Correct answer.
    4. Within 25 ft of the utility meter socket

    Explanation

    Section 230.70(A)(1) requires the service disconnecting means at a readily accessible location nearest the point of entry of the service conductors. It may be inside or outside.

  178. Question 178Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which statement about an exothermic connection to a ground rod is correct?

    1. It may be buried Correct answer.
    2. It must be accessible after installation
    3. It must be made with a mechanical connector
    4. It must be enclosed in a vault

    Explanation

    Section 250.68(A) generally requires grounding electrode connections to be accessible, but buried or concrete-encased exothermic connections are permitted. The connection need not be accessible.

  179. Question 179Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A grounding electrode conductor may be spliced using which method?

    1. Irreversible compression or exothermic weld Correct answer.
    2. A listed split-bolt connector of the correct size
    3. A terminal block with set screws and lugs
    4. A wire nut listed for the conductor size

    Explanation

    Section 250.64(C) requires the grounding electrode conductor to be continuous. It may be spliced only by irreversible compression or exothermic welding.

  180. Question 180Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A nongrounding receptacle in an older dwelling is replaced. Which method is permitted where no equipment grounding conductor exists?

    1. Connect the grounding terminal to the neutral
    2. A GFCI receptacle marked 'No Equipment Ground' Correct answer.
    3. Install a standard grounding receptacle with no ground wire
    4. Run a separate ground wire to a water pipe

    Explanation

    Section 406.4(D)(2) permits a GFCI receptacle marked 'No Equipment Ground' where no grounding conductor exists. The receptacle does not provide a ground but reduces shock hazard.

  181. Question 181Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    In a separately derived system, where is the system bonding jumper installed?

    1. At the last receptacle outlet on the system
    2. At the source, between grounded and grounding conductors Correct answer.
    3. At the utility service disconnect for the supply
    4. At the first panelboard, between grounded and equipment grounding conductors

    Explanation

    A separately derived system has its system bonding jumper at the source or first disconnecting means. It connects the grounded conductor to the grounding electrode conductor and equipment grounding conductor.

  182. Question 182Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A generator is a separately derived system when:

    1. The transfer switch switches the neutral conductor Correct answer.
    2. The generator is bonded to the building steel
    3. The transfer switch switches only the ungrounded conductors
    4. The generator frame is grounded to a rod

    Explanation

    A generator is a separately derived system when its neutral is switched by the transfer switch, isolating it from the utility neutral. If the neutral is not switched, it is not separately derived.

  183. Question 183Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    On a construction site, temporary 125-volt, 15- and 20-ampere receptacles must have:

    1. GFCI protection Correct answer.
    2. Surge protection
    3. AFCI protection
    4. Isolated grounding

    Explanation

    Section 590.6 requires GFCI protection for temporary 125-volt, 15- and 20-ampere receptacles on construction sites. This applies to all such receptacles, including those on generators.

  184. Question 184Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    The purpose of an equipotential plane in an agricultural building is to:

    1. Serve as the grounding electrode for the service
    2. Supply a neutral connection for 120-volt loads
    3. Equalize voltage between floor and metal equipment Correct answer.
    4. Provide a low-impedance path for lightning discharges

    Explanation

    Section 547.10 requires an equipotential plane in agricultural buildings to reduce voltage differences between the floor and metal equipment. This limits stray voltage hazards to livestock.

  185. Question 185Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Ground-fault protection of equipment is required for a 1000-ampere service disconnect when the voltage to ground exceeds:

    1. 120 volts
    2. 277 volts
    3. 300 volts
    4. 150 volts Correct answer.

    Explanation

    Section 230.95 requires ground-fault protection of equipment for solidly grounded wye service disconnects rated 1000 A or more where voltage to ground exceeds 150 V. The rating must not exceed 600 V phase-to-phase.

  186. Question 186Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    What is the minimum length permitted for a rod, pipe, or plate grounding electrode driven into the earth?

    1. 10 ft
    2. 6 ft
    3. 5 ft
    4. 8 ft Correct answer.

    Explanation

    Rod, pipe, and plate electrodes must be at least 8 ft long, and pipe or conduit electrodes must be at least 3/4 in. trade size. A single rod that does not measure 25 ohms or less to earth must be supplemented by one additional electrode of any permitted type.

  187. Question 187Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A Class III location is best described as which of the following?

    1. A location made hazardous by combustible dust
    2. A location hazardous due to easily ignitable fibers or flyings Correct answer.
    3. A location made hazardous by flammable gases or vapors
    4. A location made hazardous by ignitable spray application

    Explanation

    Class III locations are those made hazardous by easily ignitable fibers or flyings, such as textile mills and woodworking plants. Combustible dust defines Class II, and flammable gases or vapors define Class I.

  188. Question 188Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A Class A ground-fault circuit interrupter intended to protect personnel trips at what current range?

    1. 10 to 15 mA
    2. 20 to 30 mA
    3. 1 to 2 mA
    4. 4 to 6 mA Correct answer.

    Explanation

    Class A ground-fault circuit interrupters for personnel protection are designed to trip when the ground-fault current exceeds 4 mA and before it reaches 6 mA. This threshold is intended to interrupt current before it can produce ventricular fibrillation.

  189. Question 189Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Metal gas piping in a building is likely to become energized. What does the Code require?

    1. Bonding is not required where the piping is electrically continuous
    2. It must be bonded to the circuit equipment grounding conductor Correct answer.
    3. It must be used as a grounding electrode and bonded at the service
    4. It must be bonded with a 6 AWG copper jumper in every case

    Explanation

    Metal gas piping that is likely to become energized must be bonded to the equipment grounding conductor of the circuit that could energize it, with the bonding jumper sized from the equipment grounding conductor table. The piping is expressly prohibited from being used as a grounding electrode.

  190. Question 190Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A service is supplied by 350 kcmil copper service-entrance conductors. What is the minimum size copper grounding electrode conductor?

    1. 1/0 AWG
    2. 3/0 AWG
    3. 4 AWG
    4. 2 AWG Correct answer.

    Explanation

    The grounding electrode conductor is sized from the table based on the largest service-entrance conductor. Copper service conductors over 3/0 through 350 kcmil require a 2 AWG copper grounding electrode conductor.

  191. Question 191Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A feeder is protected by a 400-ampere overcurrent device. What is the minimum size copper equipment grounding conductor required to run with the feeder conductors?

    1. 1/0 AWG
    2. 2 AWG
    3. 3 AWG Correct answer.
    4. 6 AWG

    Explanation

    The equipment grounding conductor is sized from the table using the rating of the overcurrent device protecting the circuit. A 400-ampere device requires a 3 AWG copper equipment grounding conductor.

  192. Question 192Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    In a patient care area of a health care facility, the grounding terminal of a receptacle must be connected to the power-supply grounding terminal by which of the following?

    1. A 14 AWG copper conductor run with the circuit
    2. The branch-circuit grounding conductor, if green
    3. The metal raceway alone, where it is continuous
    4. An insulated 12 AWG copper conductor with the circuit Correct answer.

    Explanation

    Patient care areas require an insulated copper equipment grounding conductor not smaller than 12 AWG run with the circuit conductors to the receptacle grounding terminal. The metal raceway must also serve as an equipment grounding conductor, providing redundant grounding paths.

  193. Question 193Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which wiring method is permitted in a Class I, Division 2 location?

    1. Threaded rigid metal conduit Correct answer.
    2. Type AC cable
    3. Electrical nonmetallic tubing
    4. Type NM cable

    Explanation

    Class I, Division 2 locations permit wiring methods such as threaded rigid metal conduit, threaded intermediate metal conduit, Type MI cable, and listed metal-clad cable. Nonmetallic-sheathed cable and armored cable are not permitted in these locations.

  194. Question 194Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A motor has a nameplate full-load current of 24 amperes and a marked service factor of 1.15. What is the maximum rating of the motor overload device?

    1. 27 A
    2. 24 A
    3. 36 A
    4. 30 A Correct answer.

    Explanation

    For a motor with a marked service factor of 1.15 or greater, or a temperature rise of 40 degrees C or less, overload protection may be set at 125 percent of the nameplate full-load current. Here 125 percent of 24 amperes is 30 amperes.

  195. Question 195Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    When a metal underground water pipe is used as a grounding electrode, which requirement applies?

    1. It must be bonded only at the water meter
    2. It must contact earth for 10 ft and be supplemented Correct answer.
    3. It may serve as the sole electrode where the utility agrees
    4. It must be supplemented by a concrete-encased electrode only

    Explanation

    A metal underground water pipe electrode must be in direct contact with the earth for 10 ft or more, and it must be supplemented by an additional grounding electrode. The supplemental electrode may be any of the electrodes recognized by the Code.

  196. Question 196Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    The equipotential bonding connections for a permanently installed swimming pool must be made with which of the following conductors?

    1. 12 AWG solid copper
    2. 8 AWG stranded copper
    3. 6 AWG stranded copper
    4. 8 AWG solid copper Correct answer.

    Explanation

    Pool equipotential bonding conductors must be solid copper, insulated, covered, or bare, and not smaller than 8 AWG. Stranded conductors are not permitted for these bonding connections.

  197. Question 197Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Unless a specific permission applies, what is the maximum overcurrent protection permitted for a 14 AWG copper branch-circuit conductor?

    1. 25 A
    2. 15 A Correct answer.
    3. 20 A
    4. 30 A

    Explanation

    Small conductors are limited by the overcurrent protection table regardless of their calculated ampacity. A 14 AWG copper conductor is limited to a 15-ampere overcurrent device unless a specific Code permission applies.

  198. Question 198Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    A ground ring used as a grounding electrode must consist of at least how much bare copper conductor, and at what minimum burial depth?

    1. 20 ft of 6 AWG copper at 18 in
    2. 30 ft of 2 AWG copper at 36 in
    3. 20 ft of 2 AWG copper at 30 in Correct answer.
    4. 10 ft of 6 AWG copper at 24 in

    Explanation

    A ground ring must encircle the building or structure in direct contact with the earth, consist of at least 20 ft of bare copper conductor not smaller than 2 AWG, and be buried at least 30 in. below grade.

  199. Question 199Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    How must the overcurrent protective device supplying a fire pump controller be selected?

    1. To carry the motor locked-rotor current indefinitely Correct answer.
    2. At no more than 125% of the motor full-load current
    3. At the next standard rating above the motor full-load current
    4. At a value that coordinates with the building main device

    Explanation

    Fire pump supply conductors and controllers must remain energized during a fire, so the overcurrent device is selected to carry indefinitely the locked-rotor current of the fire pump motor plus the other fire pump loads. It is typically sized well above the running current and is not selected for coordination with the main device.

  200. Question 200Grounding, Bonding, Overcurrent Protection, and Special Occupancies

    Which condition must be met when circuit breakers are applied in a series-rated system?

    1. The line-side device is a current-limiting fuse with twice the downstream rating
    2. The combination is tested and listed as a series-rated combination Correct answer.
    3. The load-side breaker has an interrupting rating equal to the available fault current
    4. The load-side breaker has an instantaneous trip element

    Explanation

    A series-rated system relies on the ability of the line-side device to limit let-through current so the load-side breaker can safely interrupt a fault above its own rating. This is permitted only where the specific combination has been tested and listed, and the equipment is marked with the series rating.

MI Journeyman Electrician flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Working space depth, 0-150 volts
For equipment operating at 0 to 150 volts to ground, the clear working space in front of the equipment must be at least 3 ft deep, 30 in. wide, and 6 ft 6 in. high.
Informational Note enforceability
Informational Notes in the National Electrical Code are explanatory only. They are not mandatory rules, are not enforceable as code requirements, and are not part of the mandatory text.
AHJ authority to interpret code
Section 90.4 gives the authority having jurisdiction responsibility for interpreting the code, approving listed materials and methods, and granting written approval of alternate installations that provide equivalent safety.
Michigan Electrical Code adoption
Michigan adopts the National Electrical Code by reference with state amendments as the Michigan Electrical Code; the adopted edition and amendments control plan review and field inspection.
60 degrees C termination limit
Unless equipment is listed and marked otherwise, conductor ampacity at terminations for circuits rated 100 amperes or less is limited to the 60 degrees C column of the ampacity tables.
Table 310.16 base conditions
Ampacities in Table 310.16 assume an ambient temperature of 30 degrees C and no more than three current-carrying conductors; higher temperatures or more conductors require correction or adjustment.
Electrical Administrative Act licensing
Michigan's Electrical Administrative Act, Public Act 217 of 1956, governs licensing of electrical contractors, master and journeyman electricians, and registered electrical apprentices throughout the state.
Minimum service rating, dwelling unit
NEC 230.79(C) requires the service disconnecting means for a one-family dwelling to have a rating of not less than 100 amperes.
Small-appliance branch circuits
Dwelling unit kitchens, dining areas, and similar spaces require at least two 20-ampere small-appliance branch circuits, and those circuits may not supply outlets outside those areas.
Receptacle spacing 6-foot rule
In dwelling units, receptacle outlets must be installed so that no point along the floor line of any wall space is more than 6 feet from a receptacle outlet.
Countertop receptacle 24-inch rule
Kitchen and similar countertop receptacles must be installed so that no point along the counter wall line is more than 24 inches from a receptacle outlet.
Voltage drop 3 and 5 percent
NEC informational notes recommend limiting voltage drop to 3 percent on a branch circuit and 5 percent total for the feeder plus branch circuit combined.
Dwelling lighting load 3 VA
The general lighting load for a dwelling unit is calculated at 3 volt-amperes per square foot of floor area under NEC 220.12.
Box fill, 12 AWG
Table 314.16(B) assigns 2.25 cubic inches to each 12 AWG conductor; all equipment grounding conductors count together as one, and each device yoke counts as one conductor.
Raceway fill percentages
Chapter 9 Table 1 permits a raceway to be filled to 40 percent of its interior cross-sectional area for three or more conductors, 31 percent for two, and 53 percent for one.
EMT support intervals
Electrical metallic tubing must be fastened within 3 feet of each box or termination and supported at intervals not exceeding 10 feet along the run.
NM cable support intervals
Nonmetallic-sheathed cable must be secured within 12 inches of each box and supported at intervals not exceeding 4.5 feet along its run.
Nail plate protection
Where cables or raceways pass through bored holes in framing, they must be at least 1-1/4 inches from the nearest edge, or protected by a listed steel plate.
Straight pull box length
For a straight pull, the minimum length of a pull box is eight times the trade size of the largest raceway entering the box.
Equipment grounding conductor identification
Equipment grounding conductors must be bare, green, or green with one or more yellow stripes; white and gray identification is not permitted for these conductors.
Motor conductor 125 percent
Motor branch-circuit conductors must have an ampacity of at least 125 percent of the motor full-load current taken from the applicable Article 430 tables.
Switch height above floor
Switches and circuit breakers used as switches must not be installed more than 6 feet 7 inches above the floor or working platform.
Air-conditioning nameplate sizing
Air-conditioning conductors, disconnects, and overcurrent devices are sized from the equipment nameplate minimum circuit ampacity and the nameplate maximum overcurrent protective device rating.
Motor inverse-time breaker 250 percent
Table 430.52 permits an inverse-time circuit breaker protecting a motor branch circuit against short circuits and ground faults at up to 250 percent of motor full-load current.
Tamper-resistant receptacle requirements
Listed tamper-resistant receptacles are required in dwelling units and guest rooms, and in specified child-care, educational, and similar occupancies, under NEC 406.12.
Transformer primary-only protection
For transformers rated 1000 volts or less with primary-only overcurrent protection, the device must be sized at no more than 125 percent of the primary current.
Ground rod 25 ohms
A single ground rod or pipe electrode must have a resistance to earth of 25 ohms or less, or a supplemental electrode must be installed to supplement it.
EGC proportional increase
Where phase conductors are increased in size above the code minimum, the equipment grounding conductor must also be increased proportionally, based on circular mil area.
Small conductor overcurrent limits
NEC 240.4(D) limits overcurrent protection for small conductors: 14 AWG copper to 15 amperes, 12 AWG copper to 20 amperes, and 10 AWG copper to 30 amperes.
Standard overcurrent device ratings
NEC 240.6 lists standard ampere ratings for fuses and circuit breakers, including 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, and 600 amperes.
Class I Division 1 location
A Class I, Division 1 location is one where ignitable concentrations of flammable gases, vapors, or liquids can exist under normal operating conditions or frequently during repair and maintenance.
Pool equipotential bonding
NEC 680.26 requires an equipotential bonding grid for pools, connecting metal parts of the pool structure, fittings, and adjacent perimeter surfaces within 3 feet of the pool.

MI Journeyman Electrician study guide

General Electrical Knowledge and Code Administration

Code structure and administration

The Michigan journeyman exam tests both electrical knowledge and the administrative rules that govern electrical work. Start with NEC Article 90 (scope) and Article 100 (definitions); nearly every calculation question depends on a defined term such as service point, feeder, branch circuit, continuous load, or qualified person. Chapters 1 through 4 provide general requirements, wiring and protection, wiring methods, and equipment. Chapters 5 through 7 cover special occupancies, special equipment, and special conditions, while Chapter 8 covers communications and Chapter 9 contains tables and annexes.

Michigan adopts the NEC through statute and administrative rule, with local amendments and permitting/inspection procedures. Know that permits, inspections, and licensing are part of code compliance, not optional paperwork; work without a permit can fail inspection even when the installation is electrically sound.

Traps and a worked example

Questions often turn on mandatory language: “shall” is mandatory, “should” is advisory, and fine print notes are explanatory. Watch exceptions, because they change the general rule. Do not assume the highest insulation temperature column controls ampacity: conductor ampacity is limited by termination temperature ratings under 110.14(C). For a 100 A feeder with 75°C terminations and 75°C THWN copper, use the 75°C column: 3 AWG copper is good for 100 A. If terminations were only 60°C, 3 AWG would be limited to 85 A and a larger conductor would be required. Rule of thumb: determine the weakest link-termination, conductor insulation, or conditions of use-before selecting a size.

Services, Feeders, and Branch Circuits

Services, feeders, and branch circuits

This domain ties load calculation to conductor and overcurrent sizing. Article 220 provides standard and optional calculation methods for dwellings and other occupancies. Article 230 governs service conductors, service disconnects, and service equipment; Article 215 governs feeders; Article 210 governs branch circuits. The core rule is that conductors and overcurrent devices must be sized for the load, with continuous loads increased by 125% unless the assembly is listed for 100% operation. Receptacle, lighting, and appliance loads are calculated separately, then combined under the applicable article.

Branch-circuit requirements include receptacle spacing in dwellings, GFCI protection in specified locations, AFCI protection for dwelling branch circuits, and permissible loads on 15 A and 20 A circuits. Service disconnects must be readily accessible and located at a readily accessible point nearest the point of entry, subject to the specific rules in 230.70.

Traps and a worked example

Traps include measuring the 6 ft receptacle spacing along the floor line rather than through doorways, forgetting that a wall space 2 ft or wider needs a receptacle, mixing continuous and noncontinuous loads, and applying the 125% factor to the load but not to the overcurrent device. Another trap is assuming a 20 A circuit can carry 20 A continuously.

Worked example: a 20 A, 120 V branch circuit has a continuous load. The circuit capacity is 20 A × 120 V = 2,400 VA. For a continuous load, the load must not exceed 80% of the rating unless listed for 100%: 2,400 VA × 0.80 = 1,920 VA, or 16 A. Rule of thumb: for continuous loads, size at 125% of load; for a 20 A circuit, the continuous load limit is 16 A.

Wiring Methods, Materials, and Raceways

Wiring methods, materials, and raceways

Chapter 3 is the heart of this domain. Article 300 gives general requirements for wiring methods, including protection from physical damage, conductor identification, and support. Articles 310 through 362 cover conductors, cable assemblies, and raceways such as NM cable, AC/MC cable, EMT, PVC, rigid metal conduit, and flexible connections. You must match the wiring method to the environment: wet, damp, dry, corrosive, exposed, concealed, or subject to physical damage. Article 314 covers outlet, device, and junction boxes, including box fill; Chapter 9 provides conduit and tubing fill tables and Annex C provides preset combinations.

Traps and a worked example

Common traps include using NM cable in a wet location, ignoring support and securing distances, forgetting that raceways need expansion fittings where significant temperature change occurs, and miscounting box fill. For box fill, count each current-carrying conductor and neutral, count equipment grounding conductors as one allowance based on the largest EGC, count clamps and support fittings if present, and count each device as two conductors based on the largest conductor connected. Conduit fill also trips candidates: 1 conductor 53%, 2 conductors 31%, and 3 or more 40% of the raceway area.

Worked example: a box contains four 12 AWG current-carrying conductors, one 12 AWG equipment grounding conductor, and one device. Each 12 AWG conductor requires 2.25 in³. Four conductors = 9.00 in³; one EGC allowance = 2.25 in³; one device = two conductors = 4.50 in³. Total = 15.75 in³, so select a box with at least that volume. Rule of thumb: box fill is a volume calculation, not a wire-count guess.

Equipment, Devices, and Utilization Equipment

Equipment, devices, and utilization equipment

This domain covers how equipment is selected, rated, connected, and protected. Key articles include 404 (switches), 406 (receptacles), 408 (panelboards), 410 (luminaires), 422 (appliances), 424 (fixed electric heating), 430 (motors), 440 (air conditioning and refrigeration), and 450 (transformers). Equipment must be listed and installed per its listing and nameplate. Receptacle ratings must be coordinated with branch-circuit ratings and permissible loads. Switches and disconnects must be accessible and rated for the load, and motor circuits require separate branch-circuit short-circuit/ground-fault protection and overload protection.

Traps and a worked example

Traps include putting a 15 A single receptacle on a 20 A individual branch circuit (not permitted; a single receptacle must have a rating not less than the branch circuit), confusing GFCI and AFCI functions, using a breaker for motor overload protection instead of a separate overload device, and ignoring nameplate minimum circuit ampacity and maximum overcurrent protection on A/C equipment. Another trap is assuming a disconnect can be anywhere; many rules require it within sight of the equipment.

Worked example: a 10 hp, 460 V, three-phase motor has a nameplate full-load current of 14 A. For a standard inverse-time circuit breaker, 430.52 permits up to 250% of FLC: 14 A × 2.50 = 35 A. A 35 A breaker is a standard size, so it is acceptable as branch-circuit short-circuit/ground-fault protection, provided the separate overload protection is sized per the motor nameplate or 430.32. Rule of thumb: motor branch protection protects the circuit, not the motor; overload protection protects the motor.

Grounding, Bonding, Overcurrent Protection, and Special Occupancies

Grounding, bonding, overcurrent protection, and special occupancies

Article 250 distinguishes the grounded conductor (neutral), the equipment grounding conductor (EGC), the grounding electrode conductor (GEC), and bonding jumpers. Service equipment must have a main bonding jumper and a grounded-conductor-to-grounding-electrode connection; downstream panels must keep neutral and ground separate except where specifically permitted. The GEC is generally sized from Table 250.66 using the service conductor size, while the EGC is sized from Table 250.122 using the overcurrent device rating. Article 240 governs overcurrent protection, standard ratings, small-conductor rules, tap rules, and series-rated assemblies. Chapter 5 adds special occupancies such as pools (Article 680), emergency systems (700), and interconnected sources (705).

Traps and a worked example

Traps include sizing the GEC from the breaker rating instead of the service conductors, bonding the neutral to ground in a subpanel, using a GFCI as a substitute for equipment grounding, and forgetting that an upsized conductor may require an upsized EGC under 250.122(B). In special occupancies, pool bonding and GFCI requirements are frequently tested, as are rapid shutdown for PV systems and separation of emergency circuits.

Worked example: a 200 A service uses 2/0 AWG copper service conductors. Table 250.66 gives a 4 AWG copper GEC for 2/0 copper service conductors. The 200 A breaker does not set the GEC size; the service conductor does. By contrast, a 200 A circuit’s EGC is sized from Table 250.122, which gives 6 AWG copper. Rule of thumb: GEC follows service conductors; EGC follows the overcurrent device.

MI Journeyman Electrician cheat sheet

Quick reference

General Electrical Knowledge and Code Administration

  • The NEC is arranged in nine chapters: Chapters 1-4 contain general rules, Chapters 5-7 supplement or modify them for special occupancies, conditions, and equipment, Chapter 8 covers communications systems, and Chapter 9 contains reference tables.

  • Informational Notes are explanatory only and are not enforceable; mandatory requirements are stated with 'shall' (Article 90).

  • Ampacities in Table 310.16 assume a 30 degrees C ambient temperature and no more than three current-carrying conductors in the raceway or cable.

  • Terminations for circuits rated 100 A or less are limited to the 60 degrees C ampacity column unless the equipment is listed and marked for a higher termination temperature (110.14(C)).

  • Table 110.26(A)(1) working-space depth: 3 ft for 0-150 V to ground, 3.5 ft for 151-600 V, 4 ft for 601-2500 V; minimum width 30 in.; minimum height 6 ft 6 in.

  • The working space in front of electrical equipment must be clear and the footprint must be dedicated exclusively to electrical equipment (110.26(E)).

  • Section 90.4 gives the authority having jurisdiction responsibility for interpreting the code, approving listed materials and methods, and granting written approval of alternate installations.

  • In Michigan, electrical contractors, master and journeyman electricians, and apprentices are licensed under the Electrical Administrative Act, Public Act 217 of 1956, administered through the Bureau of Construction Codes.

  • Michigan adopts the NEC by reference with state amendments as the Michigan Electrical Code; the edition currently in effect governs plan review and field inspection.

Quick reference

Services, Feeders, and Branch Circuits

  • 230.79(C): the service disconnecting means for a one-family dwelling must have a rating of not less than 100 A.

  • 230.71: service disconnecting means must be grouped in one location, and where multiple means are permitted no more than six are allowed.

  • 310.12: 120/240 V single-phase service and feeder conductors supplying a dwelling unit may be sized at 83 percent of the service rating, with a 100 A minimum service.

  • 220.12: the general lighting load for a dwelling unit is calculated at 3 VA per square foot of floor area.

  • 210.11(C)(1): at least two 20 A small-appliance branch circuits are required for kitchen, dining, pantry, and similar receptacle outlets, and no other outlets may be supplied from them (210.52(B)(2)).

  • 210.52(A)(1): in dwelling units, no point along the floor line of any wall space may be more than 6 ft from a receptacle outlet (the 6 ft / 12 ft rule).

  • 210.52(C)(1): no point along a kitchen countertop wall line may be more than 24 in. from a receptacle outlet; islands and peninsulas require at least one receptacle.

  • Informational Notes to 210.19(A) and 215.2(A): voltage drop should not exceed 3 percent on a branch circuit or 5 percent total for feeder plus branch circuit.

  • 210.20(A): the branch-circuit overcurrent device rating must not be less than the branch-circuit conductor ampacity, and the conductors must have an ampacity not less than the load.

Quick reference

Wiring Methods, Materials, and Raceways

  • Chapter 9 Table 1 raceway fill: 53 percent for one conductor, 31 percent for two conductors, and 40 percent for three or more conductors of the interior cross-sectional area.

  • 358.30: electrical metallic tubing must be fastened within 3 ft of each box or termination and supported at intervals not exceeding 10 ft.

  • 334.30: nonmetallic-sheathed cable must be secured within 12 in. of each box and supported at intervals not exceeding 4.5 ft.

  • 300.4(A): cable or raceway through bored framing members must be at least 1-1/4 in. from the nearest edge, or protected by a steel plate at least 1/16 in. thick.

  • 314.16(B) box-fill volume per conductor: 14 AWG = 2.00 cu in., 12 AWG = 2.25 cu in., 10 AWG = 2.50 cu in.; each yoke or device counts as one conductor, and all equipment grounding conductors count together as one.

  • 314.28(A): pull-box length must be at least 8 times the trade size of the largest raceway for straight pulls, and 6 times for angle or U pulls measured between raceway entries.

  • 200.6: grounded conductors 6 AWG and smaller must be white or gray, or identified with white or gray marking at terminations.

  • 250.119: equipment grounding conductors must be bare, green, or green with one or more yellow stripes; white and gray are not permitted.

  • 310.15(B)(3)(a) ampacity adjustment for more than three current-carrying conductors in a raceway or cable: 4-6 conductors 80 percent, 7-9 conductors 70 percent, 10-20 conductors 50 percent.

Quick reference

Equipment, Devices, and Utilization Equipment

  • 430.22: motor branch-circuit conductors must have an ampacity of at least 125 percent of the motor full-load current from Table 430.248 or 430.250.

  • Table 430.52 maximum branch-circuit short-circuit protection for motors: inverse-time breaker 250 percent, dual-element fuse 175 percent, non-time-delay fuse 300 percent of full-load current.

  • 430.32: motor overload protection is sized from the nameplate service factor and temperature rise, generally 115 to 125 percent of full-load current.

  • 440.6 and 440.32: air-conditioning equipment is wired using the nameplate minimum circuit ampacity for conductors and the nameplate maximum overcurrent rating for the protective device.

  • 404.8(A): switches and circuit breakers used as switches must not be located more than 6 ft 7 in. above the floor or working platform.

  • 406.12: listed tamper-resistant receptacles are required in dwelling units, guest rooms, and specified child-care and educational occupancies.

  • 410.8: luminaires in clothes closets require 12 in. of clearance from storage space for surface-mounted incandescent types and 6 in. for recessed incandescent types.

  • 450.3(B): where only primary protection is provided for a transformer rated 1000 V or less, the primary overcurrent device may not exceed 125 percent of primary current when primary current is 9 A or more.

  • 210.21(B)(1): a single receptacle on an individual branch circuit must have a rating not less than the rating of the branch circuit.

Quick reference

Grounding, Bonding, Overcurrent Protection, and Special Occupancies

  • 250.52(A): grounding electrodes include metal underground water pipe (10 ft or more of contact), metal building frame, concrete-encased electrode (20 ft of 1/2 in. rebar), ground ring (20 ft), rod or pipe electrode (8 ft), and plate electrodes.

  • 250.53(A)(2): a single rod, pipe, or plate electrode must have a resistance to earth of 25 ohms or less, or a supplemental electrode must be added.

  • Table 250.66 copper grounding electrode conductor: 2 AWG or smaller service conductors = 8 AWG; 2/0-3/0 = 4 AWG; over 350 through 600 kcmil = 1/0; over 1100 kcmil = 3/0.

  • Table 250.122 copper equipment grounding conductor: 15 A = 14 AWG, 20 A = 12 AWG, 30-60 A = 10 AWG, 100 A = 8 AWG, 200 A = 6 AWG, 300 A = 4 AWG, 400 A = 3 AWG, 600 A = 1 AWG.

  • 250.122(B): where phase conductors are increased in size above the code minimum, the equipment grounding conductor must be increased proportionally by circular mil area.

  • 240.4(D): small conductor overcurrent limits are 15 A for 14 AWG copper, 20 A for 12 AWG copper, and 30 A for 10 AWG copper, unless specifically permitted elsewhere.

  • 240.4(B): the next higher standard overcurrent device is permitted where conductor ampacity does not exceed 800 A, the device rating does not exceed 800 A, and the circuit is not a multioutlet receptacle branch circuit.

  • Class I Division 1 locations are those where ignitable concentrations of flammable gases, vapors, or liquids exist under normal operating conditions; Division 2 locations have them only in abnormal conditions (500.5).

  • 501.15: in Class I locations, a sealing fitting must be installed within 18 in. of the enclosure boundary on raceways leaving the classified area.

MI Journeyman Electrician key terms

Authority Having Jurisdiction (AHJ)

The organization or individual - often a local electrical inspector or building department - with legal authority to enforce the code, interpret its requirements, and approve materials and installations within a given area.

Related: Approved, Michigan Electrical Code
Approved

Acceptable to the authority having jurisdiction. An installation or material becomes approved when the inspector or governing body with legal authority has accepted it for the specific use intended.

Related: Authority Having Jurisdiction (AHJ), Listed
Listed

Equipment or material that appears in a published list from a recognized testing laboratory, showing it has been tested and found suitable for a specific purpose under stated conditions.

Related: Approved, Authority Having Jurisdiction (AHJ)
Qualified Person

Someone who has the skills and knowledge related to the construction and operation of electrical equipment and installations and has received safety training to recognize and avoid the hazards involved.

Related: Authority Having Jurisdiction (AHJ)
Michigan Electrical Code

The National Electrical Code as adopted into Michigan law through the state's electrical code rules, including Michigan amendments, and enforced statewide by the electrical division and by local inspectors.

Related: Authority Having Jurisdiction (AHJ), Approved
Special Permission

Written consent from the authority having jurisdiction allowing an installation the code does not cover by a specific rule. It is required wherever the code says work may be done only by special permission.

Related: Authority Having Jurisdiction (AHJ)
Service Point

The point where service conductors from the utility connect to the premises wiring - typically at the service drop, at the service lateral, or at the terminals of the service equipment.

Related: Service Drop, Service Lateral, Feeder
Service Drop

The overhead service conductors run by the utility from the last pole or transformer to the service point at the building, including splices and the attachment to the structure.

Related: Service Point, Service Lateral
Service Lateral

The underground service conductors run from the utility's distribution line or transformer to the service point, usually at the meter or service equipment on the premises.

Related: Service Point, Service Drop
Feeder

All circuit conductors between the service equipment, the source of a separately derived system, or another supply source and the final branch-circuit overcurrent device that supplies the load.

Related: Branch Circuit, Service Point
Branch Circuit

The circuit conductors between the final overcurrent device protecting the circuit and the outlets or utilization equipment that the circuit supplies.

Related: Feeder, Outlet
Multiwire Branch Circuit

A branch circuit made up of two or more ungrounded conductors with different voltages to the neutral and a shared grounded conductor, with the ungrounded conductors connected to different phases.

Related: Branch Circuit, Grounded Conductor
Continuous Load

A load expected to run at maximum current for three hours or more. Continuous loads are figured at 125 percent of their current when sizing conductors and overcurrent protection.

Related: Demand Factor, Overcurrent Protective Device
Demand Factor

The ratio of the maximum demand of a system, or part of it, to the total connected load. It lets you size conductors and services for realistic loads rather than every load running at once.

Related: Continuous Load, Feeder
Ampacity

The maximum current, in amperes, that a conductor can carry continuously under the conditions of use without exceeding its temperature rating, after adjustment for ambient temperature and conductor count.

Related: Raceway, Overcurrent Protective Device
Raceway

An enclosed channel of metal or nonmetallic material designed for holding wires, cables, or busbars, such as conduit, electrical tubing, or wireway.

Related: Conduit Fill, Electrical Metallic Tubing (EMT)
Conduit Fill

The percentage of a raceway's internal cross-sectional area taken up by conductors. Code limits the fill so conductors do not overheat and can be pulled in without damage.

Related: Raceway, Ampacity
Box Fill

The calculation of how many conductors, devices, and fittings an outlet or junction box may hold, based on each item's volume allowance compared with the box's cubic-inch capacity.

Related: Outlet, Conduit Fill
Electrical Metallic Tubing (EMT)

A thin-wall, unthreaded steel or aluminum raceway joined with couplings and fittings. It is common indoors and in concrete and must be secured and supported at code-specified intervals.

Related: Raceway, Minimum Bending Radius
Sheathed Cable

An assembly of insulated conductors wrapped in a flexible outer jacket, such as nonmetallic-sheathed cable, used mainly for residential branch circuits and secured and supported as the code requires.

Related: Raceway, Branch Circuit
Minimum Bending Radius

The smallest curve a raceway or cable may be bent without damaging the conductors or the raceway itself, set by code as a multiple of the raceway diameter or cable size.

Related: Raceway, Electrical Metallic Tubing (EMT)
Outlet

A point on the wiring system where current is taken to supply utilization equipment. It includes receptacles, luminaires, and the junction points that serve them.

Related: Receptacle, Utilization Equipment
Receptacle

A contact device installed at an outlet for the connection of an attachment plug. It supplies cord-and-plug-connected equipment and may be single, duplex, or of another configuration.

Related: Outlet, Utilization Equipment
Utilization Equipment

Equipment that uses electrical energy for electronic, electromechanical, chemical, heating, lighting, or similar purposes. Appliances, motors, and luminaires are everyday examples.

Related: Outlet, Luminaire
Disconnecting Means

A device or group of devices that can disconnect the conductors of a circuit from their source of supply, used to de-energize equipment safely for servicing or in an emergency.

Related: Working Space, Overcurrent Protective Device
Working Space

The clear, unobstructed area in front of electrical equipment that must be kept free so people can safely work on it. Depth and width depend on voltage and site conditions.

Related: Disconnecting Means
Luminaire

A complete lighting unit, including the lamp or lamps and the parts that hold them, position them, and connect them to the power supply.

Related: Utilization Equipment
Grounded Conductor

The circuit conductor that is intentionally connected to earth at the source - usually the neutral - and that carries current during normal operation.

Related: Equipment Grounding Conductor, Main Bonding Jumper
Equipment Grounding Conductor (EGC)

The conductive path run with circuit conductors that connects metal enclosures and equipment to the grounding system, giving fault current a low-impedance path back to the source.

Related: Grounded Conductor, Grounding Electrode
Grounding Electrode

A conductive object in direct contact with the earth, such as a ground rod, metal water pipe, or concrete-encased electrode, that ties the grounding system to the earth.

Related: Equipment Grounding Conductor, Main Bonding Jumper
Main Bonding Jumper

The connection between the grounded circuit conductor and the equipment grounding conductor, or the supply-side bonding jumper, at the service or at a separately derived system.

Related: Grounded Conductor, Grounding Electrode
Overcurrent Protective Device

A device such as a fuse or circuit breaker that opens a circuit when current exceeds a set value, protecting conductors and equipment from overheating, short circuits, and ground faults.

Related: Interrupting Rating, Ampacity
Ground-Fault Circuit Interrupter (GFCI)

A device that senses a small current difference between the ungrounded and grounded conductors and quickly opens the circuit to prevent shock, required in bathrooms, kitchens, outdoors, and other wet or damp areas.

Related: Arc-Fault Circuit Interrupter (AFCI), Receptacle
Arc-Fault Circuit Interrupter (AFCI)

A device that detects the current and voltage patterns of arcing faults and opens the circuit, protecting branch circuits from fires started by damaged or loose wiring.

Related: Ground-Fault Circuit Interrupter (GFCI), Branch Circuit
Interrupting Rating

The highest current a fuse or circuit breaker is designed to safely interrupt at its rated voltage. It must equal or exceed the available fault current where the device is installed.

Related: Overcurrent Protective Device
Classified Location

An area where fire or explosion hazards may exist because of flammable gases, vapors, dusts, or fibers. Equipment installed there must be specially listed and marked for the hazard.

Related: Listed, Approved

MI Journeyman Electrician study plan

8 weeks · About 7 hours per week

Week 1

General Electrical Knowledge and Code Administration & Services, Feeders, and Branch Circuits

  • Map the NEC structure: locate any cited Article, Part, or table using the table of contents and index in under 60 seconds

  • Distinguish mandatory (shall), permissive (permitted), and informational note language, and cite three examples of each

  • Identify Michigan licensing and Code-adoption administrative rules that govern journeyman scope of work

  • Compute a single-family dwelling service load with the Article 220 Part III standard method, showing every step

Your checkpoint

A one-page personal index of the 25 most-tested Articles plus 10 completed standard-method dwelling load calculations, each step tagged with the governing section number

Week 2

Services, Feeders, and Branch Circuits

  • Size service-entrance conductors and service OCPDs using Article 230 and the dwelling service table allowance

  • Calculate feeder and neutral demand loads for a multifamily or commercial occupancy with the Article 220 optional method

  • Apply dwelling receptacle-spacing and small-appliance/laundry branch-circuit rules to a floor plan

  • Apply GFCI and AFCI protection requirements to specific branch-circuit locations

Your checkpoint

Fifteen service and feeder sizing problems solved end-to-end with cited sections, plus a room-by-room receptacle and GFCI placement plan for a two-bedroom dwelling

Week 3

Wiring Methods, Materials, and Raceways

  • Determine conductor ampacity from the wet/dry location table and apply ambient-temperature and conduit-fill adjustment factors

  • Perform box-fill calculations for outlet, device, and junction boxes including conductor, device, and equipment-grounding allowances

  • Match occupancy and location conditions to an acceptable wiring method among NM, MC, AC, PVC, and EMT

  • Verify securing, supporting, and protection-from-physical-damage requirements for three wiring methods

Your checkpoint

Twenty mixed ampacity and box-fill problems worked with cited sections, scored at 85 percent or better on a self-graded answer key

Week 4

Wiring Methods, Materials, and Raceways & Equipment, Devices, and Utilization Equipment

  • Use the Chapter 9 conduit-fill and bending tables to select raceway size and verify raceway fill for mixed conductor sizes

  • Size motor branch-circuit conductors, short-circuit protection, and overload protection for a single-motor circuit

  • Connect disconnecting-means and controller requirements to a motor installation layout

  • Interpret equipment nameplate data to select branch-circuit conductors and overcurrent devices for HVAC equipment

Your checkpoint

A timed 25-question quiz on Chapter 9 tables and Article 430/440 calculations, completed in 45 minutes and scored at 80 percent or above

Week 5

Grounding, Bonding, Overcurrent Protection, and Special Occupancies

  • Build a grounding electrode system from a site description and size grounding electrode conductors and bonding jumpers

  • Size equipment-grounding conductors for multiple circuits using the equipment-grounding conductor table and its adjustment rules

  • Apply tap-conductor and next-size-up rules to select and verify overcurrent device ratings

  • Differentiate grounding, bonding, and the grounded conductor at the service and at separately derived systems

Your checkpoint

A one-page grounding and bonding decision flowchart plus 15 grounding-electrode and equipment-grounding conductor sizing problems with cited sections

Week 6

Grounding, Bonding, Overcurrent Protection, and Special Occupancies & Equipment, Devices, and Utilization Equipment

  • Compare GFCI and AFCI requirements across dwelling, healthcare, aquatic, and assembly occupancies

  • Apply special-occupancy Articles to pool, patient-care, and emergency/standby system installations

  • Select wiring methods, boxes, and devices permitted in hazardous (classified) locations by class and division

  • Evaluate multiwire branch circuits, handle ties, and common-trip requirements for shared-neutral circuits

Your checkpoint

A comparison matrix of protection-device and wiring requirements for six special occupancies, plus a 20-question quiz scored at 80 percent or above

Week 7

General Electrical Knowledge and Code Administration & Services, Feeders, and Branch Circuits & Wiring Methods, Materials, and Raceways & Equipment, Devices, and Utilization Equipment & Grounding, Bonding, Overcurrent Protection, and Special Occupancies

  • Complete 150 mixed practice questions under timed conditions, rotating across all five domains

  • Log every missed question by domain, root cause, and correct cited section

  • Re-drill the two lowest-scoring domains until accuracy exceeds 80 percent

  • Reduce average time per calculation question to under 90 seconds

Your checkpoint

An error log of at least 50 missed items categorized by domain and root cause, with a written remediation plan naming the sections to re-study

Week 8

Services, Feeders, and Branch Circuits & Wiring Methods, Materials, and Raceways & Grounding, Bonding, Overcurrent Protection, and Special Occupancies

  • Complete two full-length 80-question simulated exams under strict timing with only the Code book as reference

  • Memorize the table locations and standard values most frequently tested: ampacity, box fill, conductor fill, and grounding conductor sizing

  • Re-verify weak areas flagged in the week 7 error log until repeat accuracy is 90 percent or better

  • Assemble a final one-page reference sheet of section numbers and exceptions to review the morning of the exam

Your checkpoint

Two completed full-length exams scored at 80 percent or better, plus a final one-page last-look sheet of high-frequency sections and tables

Milestones

Week 2: Locate 20 randomly drawn Code sections in under 60 seconds each and score 80 percent or better on a 15-question service and feeder calculation check

Week 4: Score 80 percent or better on a closed-book 30-question mixed quiz covering Domains 2 and 3, using the Code only for tables

Week 6: Score 80 percent or better on a 25-question grounding, bonding, overcurrent, and special-occupancy quiz, with every answer citing a section number

Week 8: Score 80 percent or better on two timed full-length simulated exams and reduce the week 7 error log to zero repeat mistakes

MI Journeyman Electrician exam day

Your checklist

Government-issued photo ID

Bring a current, unexpired driver's license, state ID, passport, or military ID. The name must match your registration exactly. Confirm with the provider which forms of ID are accepted and whether a second form is required.

Exam authorization / scheduling confirmation

Print or save the confirmation email or admission letter you received when you scheduled. Some centers require the authorization number before seating you.

Approved calculator

Bring a basic non-programmable calculator if permitted. Confirm with the provider which models are allowed and whether the test center supplies one or an on-screen calculator.

National Electrical Code book and approved references

Confirm with the provider which NEC edition is tested and whether the exam is open-book. If open book, bring exactly the references listed in the candidate bulletin - no extras.

Reference tabbing and handwriting policy

If the exam is open book, confirm with the provider whether tabs, highlights, and handwritten notes in your code book are permitted before you customize it.

Soft earplugs or approved noise protection

Test centers are often loud with keyboards and talking. Confirm with the provider whether foam earplugs are allowed; some centers supply them.

Layered clothing and empty pockets

Dress in layers for variable room temperature. Expect to empty pockets and store personal items in a locker; leave jewelry, watches, and hats that violate the dress code at home.

Route, parking, and arrival plan

Drive the route or check transit options beforehand. Aim to arrive at least 30 minutes before your appointment to allow for check-in and ID verification.

Snack and water for the break

If breaks are permitted, plan a quick snack and water you can access during the scheduled break. Confirm with the provider where personal items must be stored.

Practice exam logistics

Know in advance the number of questions and time limit for your exam from the candidate bulletin, and rehearse pacing on full-length practice sets.

Contact number for the test center

Save the provider's phone number so you can call immediately if you are delayed or have a vehicle problem.

Rest and a normal breakfast

Sleep on your usual schedule and eat a normal meal. Do not try a new energy drink or heavy caffeine load on exam morning.

Plan the day

Final 72 hours

Re-read the candidate bulletin and confirm every logistics item: appointment time, address, ID requirements, reference and calculator rules, and any rescheduling deadline. Call the provider if anything is unclear.

Final 72 hours

Take one or two timed full-length practice sets under exam conditions - no phone, single sitting, references only if the real exam allows them. Review missed questions by topic rather than memorizing answers.

Final 72 hours

Do a final pass on your weakest code areas using the index and table of contents, practicing how to locate articles quickly. Speed of lookup matters as much as knowledge on an open-book exam.

Final 72 hours

Pack your bag: ID, authorization, approved references, calculator, earplugs, confirmation printout. Set it by the door.

Final 24 hours

Stop heavy study. Do a light review of formula sheets, Ohm's law, conduit fill, box fill, and grounding basics, then stop.

Final 24 hours

Confirm the test center location and parking, check the weather and traffic forecast, and set two alarms. Get a full night's sleep.

Morning of

Eat a normal breakfast, hydrate moderately, and avoid heavy caffeine. Bring only approved items into the center.

Morning of

Arrive early. Complete ID verification and locker storage, then use the restroom before seating. If you are running late, call the center immediately - do not assume you will be admitted.

During the test

Read the full tutorial and confirm the on-screen calculator and reference tools. Do a first pass answering questions you know, flagging the rest, and skip time sinks.

During the test

Budget roughly one to one and a half minutes per question, reserving the final 15 to 20 minutes for flagged items and a review of your answer sheet for skipped questions.

During the test

Use the provided reference if open book, but don't verify every answer - trust well-known concepts and spend lookup time on calculation and code-reference questions.

Rules to check

  • Bring valid government-issued photo ID; the name must match your registration. If your ID name differs from your registration, resolve it with the provider before exam day.

  • Personal items - phone, smartwatch, notes, bags - are generally prohibited in the testing room. Expect to store them in a locker. Confirm with the provider what is allowed at your seat.

  • Follow the provider's break policy exactly. Unscheduled breaks may be counted against your time, and leaving the testing area may require re-verification on return.

  • Only approved references and calculators may be used. Unapproved materials or annotations can result in your exam being voided. Confirm the reference and tabbing rules with the provider.

  • Scoring is typically based on the number of correctly answered questions with no penalty for guessing, so answer every question even if you must flag and return. Confirm the passing standard in the candidate bulletin.

  • No talking, notes, or sharing of exam content. Attempting to record or reproduce questions is grounds for disqualification and possible licensing consequences.

  • If equipment fails or you feel ill, raise your hand and notify the proctor immediately rather than continuing; document any issue before you leave the center.

  • Confirm the provider's policy on rescheduling, late arrival, and retake waiting periods before exam day so you know your options if something goes wrong.

MI Journeyman Electrician FAQ

How many MI Journeyman Electrician practice questions are available?

The practice set has 200 MI Journeyman Electrician questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many MI Journeyman Electrician flashcards are available?

The flashcard set has 32 MI Journeyman Electrician cards. Each card shows the term and its definition.

Which topics does the MI Journeyman Electrician study material cover?

The MI Journeyman Electrician study material has 5 sections, including General Electrical Knowledge and Code Administration, Services, Feeders, and Branch Circuits, and Wiring Methods, Materials, and Raceways.