Journeyman Electrician overview

  • 200 practice questions
  • 32 flashcards
  • 10 study guide topics
  • 39 key terms

What you'll study

  • Electrical Theory, Ohm's Law, and Circuit Calculations10%
  • Wiring Methods and Materials15%
  • Grounding, Bonding, and Ground-Fault Protection12%
  • Overcurrent Protection and Short-Circuit Current Ratings8%
  • Branch Circuits, Feeders, and Service Load Calculations15%
  • Conductors, Cables, Ampacities, and Derating10%
  • Boxes, Raceways, Panelboards, and Equipment Installation8%
  • Motors, Transformers, HVAC, and Control Circuits10%
  • Special Occupancies, Special Equipment, and Hazardous Locations7%
  • Electrical Safety, Tools, and Jobsite Practices5%

The Journeyman Electrician credential is a state- or locally-issued license that certifies you to perform electrical installation work under the scope your jurisdiction defines, and it is usually the step between a trainee or apprentice classification and a master's license. It is aimed at electricians who have already accumulated the supervised field hours their licensing board requires and who can now demonstrate, on a written exam, that they can apply code rules to real installations. The exam is built around the National Electrical Code as adopted in your area, plus the local amendments that modify it, and it spreads across theory and circuit math, wiring methods, grounding and bonding, overcurrent protection, load calculations, conductor ampacity and derating, boxes and raceways, motors and transformers, special occupancies, and jobsite safety. Expect a mixture of multiple-choice items and calculation problems, with a code book permitted in many but not all jurisdictions. Preparation that works is active: practice navigating the code quickly, drill the calculations until they are automatic, and take timed practice sets so lookup speed stops being your limiting factor. Confirm every administrative detail with your licensing board, since requirements differ by jurisdiction.

Common mistakes

On combination series-parallel circuits, the candidate divides the full source voltage by each individual parallel branch resistance to get branch current, ignoring voltage drops that occur across series elements ahead of the parallel group.

Memorized 'voltage is the same in parallel' and applies the source voltage to branches even though a series resistor ahead of the split has already dropped part of it.

What to do instead

Reduce each parallel group to one equivalent resistance, add the series elements to find total resistance, compute total current from the source voltage, then work backwards: subtract each series voltage drop from the source to find the actual voltage across the parallel group before dividing by individual branch resistances.

Sizes conduit for a two-conductor pull using the 40% fill column, and for a single conductor also using 40%.

The '40%' number gets memorized as the universal raceway fill limit because most pulls involve three or more conductors.

What to do instead

Use Chapter 9, Table 1: 53% for one conductor, 31% for two conductors, 40% only for over two conductors; then read the actual square-inch area from Chapter 9, Table 4 or 5 for the specific raceway type and size rather than estimating from trade size.

Uses Table 250.122 (equipment grounding conductor sized by overcurrent device rating) to size the grounding electrode conductor to a rod or water pipe.

Both tables contain a column that looks like an overcurrent rating or conductor size, and both are titled with 'grounding,' so they get swapped under time pressure.

What to do instead

Anchor the distinction: grounding electrode conductors come from 250.66 and are sized by the largest service-phase conductor; equipment grounding conductors come from 250.122 and are sized by the rating of the overcurrent device protecting the circuit. Sketch which conductor lands where before opening the table.

Rounds a calculated overcurrent device up to the next standard size in every situation, including small-conductor branch circuits and cases where the next size exceeds 800 A.

The 'next size up' rule from 240.4(B) gets memorized as an unconditional allowance without its three conditions.

What to do instead

Before rounding up, verify all of 240.4(B): the conductors are not supplying multioutlet receptacle circuits for cord-and-plug loads, the ampacity does not already match a standard rating, and the next higher standard size does not exceed 800 A. Also check 240.4(D) small-conductor limits and any 240.4(G) specific-circuit rules, which override the general allowance.

Applies the 35% demand factor to the entire calculated general lighting load for a dwelling instead of only to the portion above 3,000 VA.

Table 220.42 is read as a single '35%' factor and the tiered structure of the table is skipped.

What to do instead

Split the general lighting load into tiers before applying anything: first 3,000 VA at 100%, 3,001 through 120,000 VA at 35%, remainder at 25%; keep the 1,500 VA small-appliance and laundry circuits separate at 100% per 220.52, then add the largest of the heating or cooling load.

Reads conductor ampacity straight from the 90 degrees C column for a THHN conductor terminated on a 75 degrees C lug, or defaults everything to the 60 degrees C column.

The insulation rating on the conductor is confused with the termination temperature limit, and the equipment label is not checked.

What to do instead

Ampacity is the lesser of the conductor's table value and the termination limit: check the equipment marking under 110.14(C) first, then read the corresponding column of the ampacity table. Keep separate scratch columns for 'insulation ampacity' (used for derating and adjustment) and 'final ampacity' (after applying termination limits and adjustment/correction factors).

Counts box fill by counting only the current-carrying conductors and the device, leaving out cable clamps, equipment grounding conductors, or counting a single-gang device as one conductor.

The mental image of 'wires in a box' excludes hardware, and 314.16(B) item-by-item counting is slow under exam time pressure.

What to do instead

Build a fill tally line by line: each unbroken conductor counts once, each conductor cut or spliced counts once, all equipment grounding conductors together count as one based on the largest, each cable clamp or connector counts as one, and each single-gang yoke or strap counts as two. Multiply the count by the volume per conductor from Table 314.16(B) and compare to the box's marked volume.

Sizes the motor branch-circuit short-circuit and ground-fault protective device from the conductor ampacity or the nameplate current instead of from the table full-load current, and skips the 125% multiplier on branch-circuit conductors.

The motor is treated like a standard appliance branch circuit, so 210.20 and conductor ampacity are used where 430.22 and 430.52 govern.

What to do instead

Use the sequence: Table 430.250 full-load current (not nameplate) at 125% for branch-circuit conductors; overload protection from 430.32 based on nameplate or service factor; short-circuit and ground-fault protection sized as a percentage of Table 430.250 FLC per Table 430.52, verifying the conductor is still protected. Keep the three protections physically distinct on scratch paper.

Specifies metallic liquidtight flexible conduit with standard fittings, or nonmetallic conduit, for the wiring method in a Class I, Division 1 location.

The location is treated like an ordinary wet or industrial area, and the division classification is not connected to the wiring-method table.

What to do instead

First confirm the class, division or zone, and group, then open the article 500-series wiring method table for that exact combination (501.10(A) for Class I, Division 1, for example, which requires threaded rigid metal conduit or threaded IMC, MI cable, or specific listed cable types). Division 2 relaxes the method, so never downgrade Division 1 requirements to Division 2 allowances.

Verifies a circuit is de-energized for troubleshooting using only a non-contact voltage tester, or uses a multimeter that has not been checked on a known live source.

Speed and habit on the job; the tester is treated as an indicator rather than as a test instrument requiring validation.

What to do instead

Follow the test-before-and-after sequence: confirm the meter and leads on a known energized source, test the conductors being worked, then re-test the meter. Use only a meter rated for the available voltage and category, apply the shock and arc-flash PPE the task requires, and treat non-contact testers as screening only, never as the sole verification.

Exam requirements can change. Confirm current details with the exam provider.

Journeyman Electrician practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Electrical Theory, Ohm's Law, and Circuit Calculations

    A 120 V source is connected across a 24 Ω resistor. What current flows in the circuit?

    1. 0.2 A
    2. 5 A Correct answer.
    3. 120 A
    4. 2.9 A

    Explanation

    Ohm's law states that current equals voltage divided by resistance, so I = V/R. Substituting gives 120 V ÷ 24 Ω = 5 A. The result is a direct-current value with no other adjustments needed for a purely resistive load.

  2. Question 2Electrical Theory, Ohm's Law, and Circuit Calculations

    A resistive load draws 10 A from a 120 V supply. What power does the load consume?

    1. 12 W
    2. 12,000 W
    3. 120 W
    4. 1200 W Correct answer.

    Explanation

    For a resistive load, power equals voltage multiplied by current, P = V × I. Here 120 V × 10 A = 1200 W. This is equivalent to 1.2 kW.

  3. Question 3Electrical Theory, Ohm's Law, and Circuit Calculations

    Resistors of 10 Ω, 20 Ω, and 30 Ω are connected in series. What is the total resistance of the combination?

    1. 600 Ω
    2. 60 Ω Correct answer.
    3. 3.3 Ω
    4. 20 Ω

    Explanation

    In a series circuit the same current passes through every resistor, so the individual resistances simply add. The total is 10 Ω + 20 Ω + 30 Ω = 60 Ω. Series totals are always larger than the largest individual resistor.

  4. Question 4Electrical Theory, Ohm's Law, and Circuit Calculations

    Two 12 Ω resistors are connected in parallel across a supply. What is the equivalent resistance of the pair?

    1. 12 Ω
    2. 24 Ω
    3. 3 Ω
    4. 6 Ω Correct answer.

    Explanation

    For two resistors in parallel, the reciprocal formula gives 1/RT = 1/12 + 1/12 = 2/12, so RT = 6 Ω. A shortcut for two equal resistors is to divide the value by two. A parallel combination is always smaller than the smallest branch resistance.

  5. Question 5Electrical Theory, Ohm's Law, and Circuit Calculations

    Which quantity has the same value at every point in a series circuit?

    1. Voltage
    2. Current Correct answer.
    3. Power
    4. Resistance

    Explanation

    A series circuit provides only one conductive path, so the same current must pass through every element. Voltage, on the other hand, divides among the loads in proportion to their resistances. Resistance and power both vary from component to component.

  6. Question 6Electrical Theory, Ohm's Law, and Circuit Calculations

    A 1500 W space heater operates for 2 hours. How much energy does it use?

    1. 3 kWh Correct answer.
    2. 30 kWh
    3. 1.5 kWh
    4. 0.75 kWh

    Explanation

    Energy in kilowatt-hours equals power in kilowatts multiplied by time in hours. Converting 1500 W to 1.5 kW and multiplying by 2 hours gives 3 kWh. Utility billing is based on this kilowatt-hour quantity.

  7. Question 7Electrical Theory, Ohm's Law, and Circuit Calculations

    A 120 V series circuit has voltage drops of 45 V and 30 V across two resistors. What is the voltage drop across the third resistor?

    1. 195 V
    2. 15 V
    3. 45 V Correct answer.
    4. 75 V

    Explanation

    Kirchhoff's voltage law requires the sum of the voltage drops around a closed loop to equal the applied voltage. The two known drops total 75 V, so the remaining drop is 120 V − 75 V = 45 V. The full source voltage is thus accounted for.

  8. Question 8Electrical Theory, Ohm's Law, and Circuit Calculations

    At a junction, two conductors supply 3 A and 5 A. One conductor leaves the junction carrying 4 A. What current leaves through the remaining conductor?

    1. 2 A
    2. 4 A Correct answer.
    3. 12 A
    4. 8 A

    Explanation

    Kirchhoff's current law states that total current entering a junction equals total current leaving it. The incoming total is 3 A + 5 A = 8 A, so the unknown outgoing current is 8 A − 4 A = 4 A. Charge is conserved at the node.

  9. Question 9Electrical Theory, Ohm's Law, and Circuit Calculations

    A 100 V source is applied across a series combination of 30 Ω and 70 Ω. What voltage appears across the 70 Ω resistor?

    1. 70 V Correct answer.
    2. 100 V
    3. 30 V
    4. 50 V

    Explanation

    The total resistance is 30 Ω + 70 Ω = 100 Ω, so the current is 100 V ÷ 100 Ω = 1 A. The drop across the 70 Ω resistor is then 1 A × 70 Ω = 70 V. In a series circuit, voltage divides in direct proportion to resistance.

  10. Question 10Electrical Theory, Ohm's Law, and Circuit Calculations

    A 24 V source feeds two parallel branches of 8 Ω and 12 Ω. What total current does the source supply?

    1. 5 A Correct answer.
    2. 2 A
    3. 12 A
    4. 3 A

    Explanation

    Each parallel branch sees the full 24 V, so the branch currents are 24 V ÷ 8 Ω = 3 A and 24 V ÷ 12 Ω = 2 A. Kirchhoff's current law gives a source current of 3 A + 2 A = 5 A. Branch currents add in a parallel circuit.

  11. Question 11Electrical Theory, Ohm's Law, and Circuit Calculations

    A conductor is replaced with one of the same material and cross-sectional area but twice the length. How does its resistance change?

    1. It is doubled Correct answer.
    2. It is halved
    3. It is quadrupled
    4. It stays the same

    Explanation

    Resistance is given by R = ρL/A, so it is directly proportional to length when resistivity and area are fixed. Doubling the length therefore doubles the resistance. Cross-sectional area, by contrast, affects resistance inversely.

  12. Question 12Electrical Theory, Ohm's Law, and Circuit Calculations

    A 120 V branch circuit carries 15 A through conductors whose total loop resistance is 0.4 Ω. What is the voltage drop in the conductors?

    1. 48 V
    2. 3 V
    3. 1.6 V
    4. 6 V Correct answer.

    Explanation

    Voltage drop equals current multiplied by the total conductor resistance of the loop, VD = I × R. Using the round-trip resistance already given, 15 A × 0.4 Ω = 6 V. The load then receives approximately 114 V.

  13. Question 13Electrical Theory, Ohm's Law, and Circuit Calculations

    A sinusoidal voltage has a peak value of 170 V. What is its root-mean-square value?

    1. 85 V
    2. 340 V
    3. 170 V
    4. 120 V Correct answer.

    Explanation

    For a sine wave, RMS value equals peak value divided by the square root of 2, or about 0.707 times the peak. Here 170 V × 0.707 ≈ 120 V. RMS is the value that produces the same heating effect as an equal DC voltage.

  14. Question 14Electrical Theory, Ohm's Law, and Circuit Calculations

    What is the inductive reactance of a 0.1 H inductor at 60 Hz?

    1. 0.6 Ω
    2. 377 Ω
    3. 6 Ω
    4. 37.7 Ω Correct answer.

    Explanation

    Inductive reactance is calculated with XL = 2πfL. Substituting gives 2 × π × 60 Hz × 0.1 H ≈ 37.7 Ω. Reactance rises in direct proportion to both frequency and inductance.

  15. Question 15Electrical Theory, Ohm's Law, and Circuit Calculations

    An ideal transformer has a 480 V primary and a 120 V secondary. If the primary current is 5 A, what is the secondary current?

    1. 1.25 A
    2. 5 A
    3. 20 A Correct answer.
    4. 80 A

    Explanation

    In an ideal transformer, input volt-amperes equal output volt-amperes, so Vp × Ip = Vs × Is. The primary power is 480 V × 5 A = 2400 VA, and 2400 VA ÷ 120 V = 20 A. Stepping voltage down by a factor of four steps current up by the same factor.

  16. Question 16Electrical Theory, Ohm's Law, and Circuit Calculations

    Two capacitors of 10 µF and 20 µF are connected in parallel. What is the total capacitance?

    1. 10 µF
    2. 15 µF
    3. 30 µF Correct answer.
    4. 6.7 µF

    Explanation

    Capacitances in parallel add directly, just as plate area adds, so 10 µF + 20 µF = 30 µF. This is the opposite of the resistor rule for parallel elements. Capacitors in series, however, combine with a reciprocal formula.

  17. Question 17Electrical Theory, Ohm's Law, and Circuit Calculations

    Two 20 Ω resistors are connected in parallel, and that pair is connected in series with a 10 Ω resistor. What is the total resistance?

    1. 15 Ω
    2. 50 Ω
    3. 30 Ω
    4. 20 Ω Correct answer.

    Explanation

    First reduce the parallel pair: 20 Ω in parallel with 20 Ω equals 10 Ω. Then add the series element: 10 Ω + 10 Ω = 20 Ω. Always reduce parallel groups before adding series portions.

  18. Question 18Electrical Theory, Ohm's Law, and Circuit Calculations

    A 240 V single-phase load draws 20 A at a power factor of 0.8. What is the true power consumed?

    1. 1920 W
    2. 3840 W Correct answer.
    3. 6000 W
    4. 4800 W

    Explanation

    True power in an AC circuit is P = V × I × power factor. Substituting gives 240 V × 20 A × 0.8 = 3840 W. The apparent power of 4800 VA includes the reactive component that does no useful work.

  19. Question 19Electrical Theory, Ohm's Law, and Circuit Calculations

    A balanced three-phase load operates at 480 V, 20 A, with a power factor of 0.9. What is the approximate real power?

    1. 17.3 kW
    2. 8.6 kW
    3. 15 kW Correct answer.
    4. 30 kW

    Explanation

    Real power in a balanced three-phase system is P = √3 × V(line) × I(line) × power factor. Computing 1.732 × 480 V × 20 A × 0.9 gives about 14,964 W, or roughly 15 kW. Omitting the √3 factor gives the incorrect single-phase result.

  20. Question 20Electrical Theory, Ohm's Law, and Circuit Calculations

    A motor delivers 10 hp of mechanical output at 90 percent efficiency. What input power does it draw?

    1. 9.2 kW
    2. 8.29 kW Correct answer.
    3. 7.46 kW
    4. 6.71 kW

    Explanation

    First convert the output to watts: 10 hp × 746 W/hp = 7460 W. Because efficiency is output divided by input, the input is 7460 W ÷ 0.90 ≈ 8289 W, or about 8.29 kW. Input power is always greater than output power for a real machine.

  21. Question 21Wiring Methods and Materials

    Type NM cable must be secured within what distance of each box or fitting?

    1. 24 inches
    2. 9 inches
    3. 12 inches Correct answer.
    4. 6 inches

    Explanation

    Section 334.30 requires nonmetallic-sheathed cable to be secured within 12 inches of every box or fitting and at intervals not exceeding 4 1/2 feet. The 12-inch dimension keeps the sheath from being damaged where it enters the enclosure.

  22. Question 22Wiring Methods and Materials

    The total bends between pull points in a run of electrical metallic tubing shall not exceed which amount?

    1. 180 degrees
    2. 450 degrees
    3. 360 degrees Correct answer.
    4. 270 degrees

    Explanation

    Raceway installations limit the sum of all bends between boxes, conduit bodies, or fittings to 360 degrees so conductors can be pulled without excessive tension. Four quarter bends is the maximum regardless of the number of individual bends used.

  23. Question 23Wiring Methods and Materials

    Where a raceway contains three or more conductors, the conductors may fill no more than what percentage of the raceway's interior cross-sectional area?

    1. 40 percent Correct answer.
    2. 31 percent
    3. 60 percent
    4. 53 percent

    Explanation

    Chapter 9, Table 1 limits raceway fill for three or more conductors to 40 percent of the interior cross-sectional area. The smaller percentages apply only to one or two conductors in the raceway.

  24. Question 24Wiring Methods and Materials

    Splices and joints in conductors must be enclosed in a box or conduit body that is which of the following?

    1. Listed for wet locations
    2. Concealed in the building finish
    3. Permanently sealed
    4. Readily accessible Correct answer.

    Explanation

    Section 300.15 requires spliced conductors to be enclosed, and the enclosure must remain accessible so the connection can be inspected or serviced. Concealing a splice inside a finished wall or ceiling is prohibited.

  25. Question 25Wiring Methods and Materials

    Where NM cable passes through a bored hole less than 1 1/4 inches from the nearest edge of a framing member, protection must be provided by a steel plate at least how thick?

    1. 1/32 inch
    2. 3/64 inch
    3. 1/16 inch Correct answer.
    4. 1/8 inch

    Explanation

    Section 300.4(D) requires a steel plate not less than 1/16 inch thick where the cable is closer than 1 1/4 inches to the edge of the framing member. The plate prevents nails and screws driven into the framing from penetrating the cable.

  26. Question 26Wiring Methods and Materials

    Type NM cable is permitted to be installed in which of the following locations?

    1. Embedded in poured concrete
    2. In a hoistway
    3. In a wet location
    4. Inside a dry, heated crawlspace Correct answer.

    Explanation

    Section 334.10 permits NM cable in normally dry locations such as a dry, heated crawlspace, which is why the cable's outer jacket is rated for dry use. Wet locations, hoistways, and embedment in concrete are all prohibited by Section 334.12.

  27. Question 27Wiring Methods and Materials

    Electrical metallic tubing must be securely fastened within what distance of each box or fitting?

    1. 3 feet Correct answer.
    2. 10 feet
    3. 6 feet
    4. 5 feet

    Explanation

    Section 358.30 requires EMT to be secured within 3 feet of each box, conduit body, or fitting, and at intervals not exceeding 10 feet thereafter. The 3-foot rule limits strain on the enclosure entry.

  28. Question 28Wiring Methods and Materials

    At each outlet, switch, or junction box, the minimum length of free conductor that must be left for splices or terminations is which of the following?

    1. 4 inches
    2. 2 inches
    3. 6 inches Correct answer.
    4. 3 inches

    Explanation

    Section 300.14 requires at least 6 inches of free conductor measured from the point where the conductor emerges from its raceway or cable sheath. At least 3 inches must extend outside the box opening.

  29. Question 29Wiring Methods and Materials

    A box contains four 12 AWG ungrounded and grounded conductors, one cable clamp, one equipment grounding conductor, and one device yoke. Using 2.25 cubic inches per 12 AWG conductor, what is the minimum box volume required?

    1. 18.00 cubic inches Correct answer.
    2. 22.50 cubic inches
    3. 15.75 cubic inches
    4. 20.25 cubic inches

    Explanation

    Section 314.16(B) counts the four conductors, one for the clamp, one for the equipment grounding conductor, and two for the device yoke, for a total of eight conductor volumes. Eight times 2.25 cubic inches equals 18.00 cubic inches.

  30. Question 30Wiring Methods and Materials

    Schedule 40 rigid PVC conduit of 1/2-inch trade size installed in a straight horizontal run must be supported at intervals not exceeding which distance?

    1. 3 feet Correct answer.
    2. 2 feet
    3. 5 feet
    4. 18 inches

    Explanation

    Table 352.30 sets the support interval for 1/2-inch through 1-inch PVC at 3 feet. Larger sizes are permitted longer intervals, up to 6 feet for the largest trade sizes.

  31. Question 31Wiring Methods and Materials

    Type UF cable is direct buried as a feeder beneath a residential lawn. What is the minimum cover required?

    1. 30 inches
    2. 12 inches
    3. 24 inches Correct answer.
    4. 18 inches

    Explanation

    Table 300.5 lists 24 inches as the minimum cover for direct-buried UF cable for feeders and general branch circuits. The reduced 12-inch cover applies only to residential branch circuits limited to 120 volts and 20 amperes with ground-fault protection.

  32. Question 32Wiring Methods and Materials

    What is the minimum radius to the inner edge of a bend for 1/2-inch electrical metallic tubing?

    1. 4 inches Correct answer.
    2. 3 inches
    3. 2 1/2 inches
    4. 2 inches

    Explanation

    Table 358.24 specifies a minimum bend radius of 4 inches for 1/2-inch EMT. Bending tighter than the table value can flatten or kink the tubing and damage conductors during a pull.

  33. Question 33Wiring Methods and Materials

    Type AC cable must be supported at intervals not exceeding which distance?

    1. 4 1/2 feet Correct answer.
    2. 6 feet
    3. 3 feet
    4. 4 feet

    Explanation

    Section 320.30 requires armored cable to be secured at intervals not exceeding 4 1/2 feet and within 12 inches of each box or fitting. The same 4 1/2-foot interval applies to NM cable.

  34. Question 34Wiring Methods and Materials

    Interlocked-armor Type MC cable must be secured at intervals not exceeding which distance?

    1. 6 feet Correct answer.
    2. 10 feet
    3. 4 1/2 feet
    4. 3 feet

    Explanation

    Section 330.30 requires Type MC cable to be supported at intervals not exceeding 6 feet and within 12 inches of boxes and fittings, with limited exceptions for certain industrial and cable-tray installations.

  35. Question 35Wiring Methods and Materials

    The sum of the cross-sectional areas of all conductors installed in a metal wireway may not exceed what percentage of the wireway's interior cross-sectional area at any point?

    1. 10 percent
    2. 20 percent Correct answer.
    3. 40 percent
    4. 25 percent

    Explanation

    Section 376.22 limits conductor fill in wireways to 20 percent of the interior cross-sectional area at any cross section. The generous space allows conductors to be laid in without damage and helps dissipate heat.

  36. Question 36Wiring Methods and Materials

    Liquidtight flexible metal conduit of 1/2-inch trade size must be supported at intervals not exceeding which distance?

    1. 5 feet
    2. 4 feet
    3. 3 feet Correct answer.
    4. 18 inches

    Explanation

    Table 350.30 sets a support interval of 3 feet for 1/2-inch through 1-inch liquidtight flexible metal conduit. Larger trade sizes are permitted intervals of 3 1/2 to 6 feet.

  37. Question 37Wiring Methods and Materials

    A straight run of rigid PVC conduit is installed between two fixed enclosures and will be exposed to a seasonal temperature swing. What must the installation include?

    1. A bonding jumper
    2. An expansion fitting Correct answer.
    3. A seal-off fitting
    4. An equipment grounding conductor

    Explanation

    Section 352.44 requires expansion fittings where a PVC raceway is subject to thermal expansion and contraction, such as a straight run between fixed points. Without them, the conduit can bow or pull apart at joints.

  38. Question 38Wiring Methods and Materials

    A box used to support a ceiling-suspended paddle fan must be which of the following?

    1. Made of metal
    2. Listed and marked for the application Correct answer.
    3. At least 4 inches deep
    4. Installed with a box extension

    Explanation

    Section 314.27(C) requires boxes that support ceiling-suspended paddle fans to be listed and marked for that use. The marking confirms the box and its mounting means can carry the fan's weight and vibration.

  39. Question 39Wiring Methods and Materials

    How much volume must be counted for each 14 AWG conductor when calculating box fill?

    1. 2.50 cubic inches
    2. 2.00 cubic inches Correct answer.
    3. 1.50 cubic inches
    4. 2.25 cubic inches

    Explanation

    Table 314.16(B) assigns 2.00 cubic inches to each 14 AWG conductor, 2.25 cubic inches to each 12 AWG conductor, and 2.50 cubic inches to each 10 AWG conductor. The same values apply to clamps, support fittings, and equipment grounding conductors as counted in Section 314.16(B).

  40. Question 40Wiring Methods and Materials

    Rigid PVC conduit is direct buried beneath a residential lawn to supply a detached garage. What is the minimum cover required?

    1. 24 inches
    2. 18 inches Correct answer.
    3. 12 inches
    4. 6 inches

    Explanation

    Table 300.5 requires a minimum cover of 18 inches for rigid PVC conduit installed direct buried in earth. The greater depths in the table apply to roadways, airport runways, and similar areas.

  41. Question 41Wiring Methods and Materials

    In a Class I, Division 1 location, a seal-off fitting must be installed within what distance of each conduit entering an enclosure?

    1. 24 inches
    2. 12 inches
    3. 18 inches Correct answer.
    4. 36 inches

    Explanation

    Section 501.15(A)(1) requires a seal-off fitting in each conduit run entering an enclosure in a Class I, Division 1 location, located within 18 inches of the enclosure. The seal limits the passage of gases or vapors through the conduit system.

  42. Question 42Wiring Methods and Materials

    Flexible metal conduit may serve as an equipment grounding conductor where the circuit is protected at 20 amperes or less, the length does not exceed 6 feet, and which other condition is met?

    1. The entire run is installed in a dry location
    2. The conduit is 1 1/4 inches or larger in trade size
    3. Listed grounding fittings are used Correct answer.
    4. The circuit contains no splices or joints

    Explanation

    Section 250.118(5) recognizes flexible metal conduit as an equipment grounding conductor only for short lengths (6 feet or less) on circuits protected at 20 amperes or less, and only when terminated with fittings listed for grounding. The listed fittings ensure a reliable low-impedance path.

  43. Question 43Wiring Methods and Materials

    What is the maximum number of 12 AWG THHN copper conductors permitted in a 1/2-inch electrical metallic tubing raceway?

    1. 6
    2. 12
    3. 14
    4. 9 Correct answer.

    Explanation

    The 40 percent fill area for 1/2-inch EMT is about 0.122 square inch, and each 12 AWG THHN conductor occupies about 0.0133 square inch. Dividing gives just over nine conductors, so nine is the maximum permitted.

  44. Question 44Wiring Methods and Materials

    How much volume must be counted for each 6 AWG conductor in a box-fill calculation?

    1. 4.50 cubic inches
    2. 3.00 cubic inches
    3. 4.00 cubic inches
    4. 5.00 cubic inches Correct answer.

    Explanation

    Table 314.16(B) assigns 5.00 cubic inches to each 6 AWG conductor. The table values increase with conductor size, and the same volume applies to an equipment grounding conductor of that size.

  45. Question 45Wiring Methods and Materials

    A conduit nipple 24 inches or less in length, installed between boxes or enclosures, may be filled to what percentage of its cross-sectional area?

    1. 60 percent Correct answer.
    2. 40 percent
    3. 31 percent
    4. 50 percent

    Explanation

    Note 4 to Chapter 9, Table 1 permits nipple raceways 24 inches or less in length to be filled to 60 percent of the interior cross-sectional area. The short length makes conductor pulling practical despite the higher fill.

  46. Question 46Wiring Methods and Materials

    Type NM cable installed along the side of wood framing must be supported at intervals not exceeding what distance, and within what distance of each box?

    1. 4 1/2 ft, and within 12 in of each box Correct answer.
    2. 3 ft, and within 6 in of each box
    3. 6 ft, and within 8 in of each box
    4. 10 ft, and within 18 in of each box

    Explanation

    Nonmetallic-sheathed cable must be secured by staples, straps, or similar fittings so that it is supported at intervals not exceeding 4 1/2 ft and within 12 in of every box or fitting. The 12-in rule keeps strain off terminations at the enclosure.

  47. Question 47Wiring Methods and Materials

    Where is it permitted to make a splice or joint in conductors that are part of a raceway wiring method?

    1. Anywhere, provided the splice is insulated with tape and compound
    2. In a box, conduit body, or fitting identified for the purpose Correct answer.
    3. Anywhere in the run that remains accessible after construction
    4. At any point in the run where the splice is made with listed connectors

    Explanation

    Conductor splices and joints must be enclosed in an approved box, conduit body, or fitting designed for the purpose so the connection is protected and accessible. Making up joints inside a raceway or in an open run is not permitted regardless of the connector type.

  48. Question 48Wiring Methods and Materials

    A single receptacle is mounted in a box and connected to 12 AWG circuit conductors. How many conductor volumes must be counted for the device when calculating box fill?

    1. One conductor volume, counted at 12 AWG
    2. Two conductor volumes, counted at 12 AWG Correct answer.
    3. Two conductor volumes, counted at 14 AWG
    4. One conductor volume, counted at 18 AWG

    Explanation

    Each device or equipment, such as a receptacle or switch, is counted as two conductors based on the largest conductor connected to it. Here the largest conductor is 12 AWG, so the receptacle adds the equivalent of two 12 AWG volumes to the box fill.

  49. Question 49Wiring Methods and Materials

    Rigid metal conduit of 1-inch trade size installed in a straight horizontal run must be supported at intervals not exceeding which distance?

    1. 14 ft
    2. 10 ft
    3. 16 ft
    4. 12 ft Correct answer.

    Explanation

    Support spacing for rigid metal conduit increases with trade size; 1-inch raceway is permitted to be supported at intervals not exceeding 12 ft. The run must also be secured within 3 ft of each box or termination fitting.

  50. Question 50Wiring Methods and Materials

    Which of the following wiring methods is permitted to be installed in an air-handling plenum used to move environmental air?

    1. Type NM cable
    2. Schedule 40 rigid PVC conduit
    3. Electrical metallic tubing Correct answer.
    4. Electrical nonmetallic tubing

    Explanation

    In spaces used to move environmental air, only wiring methods specifically permitted for such spaces may be used; metal raceways such as electrical metallic tubing qualify. Nonmetallic methods like PVC conduit, ENT, and NM cable are prohibited because of smoke and flame-spread characteristics of their materials.

  51. Question 51Grounding, Bonding, and Ground-Fault Protection

    A 20-ampere branch circuit is run with 12 AWG copper conductors. What is the minimum-size copper equipment grounding conductor required in the same raceway?

    1. 10 AWG
    2. 8 AWG
    3. 14 AWG
    4. 12 AWG Correct answer.

    Explanation

    Table 250.122 sizes the equipment grounding conductor according to the rating of the overcurrent device protecting the circuit, and a 20-ampere device requires 12 AWG copper (10 AWG aluminum). A larger conductor may be installed, but it is not required.

  52. Question 52Grounding, Bonding, and Ground-Fault Protection

    A metal underground water pipe may be used as a grounding electrode only if it is in direct contact with the earth for at least what length?

    1. 8 ft
    2. 20 ft
    3. 4 ft
    4. 10 ft Correct answer.

    Explanation

    Section 250.52(A)(1) recognizes a metal underground water pipe as a grounding electrode only where 10 ft or more of the pipe is in direct contact with the earth. Where the pipe is interrupted by an insulating joint or water meter, the connection must be made around it per 250.53(D)(1).

  53. Question 53Grounding, Bonding, and Ground-Fault Protection

    What is the minimum length of a rod-type grounding electrode permitted by the NEC?

    1. 10 ft
    2. 12 ft
    3. 15 ft
    4. 8 ft Correct answer.

    Explanation

    Section 250.52(A)(5) requires rod and pipe electrodes to be at least 8 ft in length. Rods of iron or steel must also be at least 5/8 inch in diameter, while listed nonferrous or stainless steel rods may be 1/2 inch in diameter.

  54. Question 54Grounding, Bonding, and Ground-Fault Protection

    A listed Class A ground-fault circuit interrupter is designed to trip at a ground-fault current of approximately:

    1. 2 mA
    2. 5 mA Correct answer.
    3. 3 mA
    4. 1 mA

    Explanation

    Class A ground-fault circuit interrupters are listed to trip when the ground-fault current reaches 5 mA, plus or minus 1 mA, a level selected to protect people from ventricular fibrillation. Ground-fault protection of equipment operates at far higher currents for a different purpose.

  55. Question 55Grounding, Bonding, and Ground-Fault Protection

    An insulated equipment grounding conductor, 6 AWG and smaller, must be identified by which color scheme?

    1. Any color if it is tagged at both ends
    2. White or gray
    3. Black with a green tag at each termination
    4. Green, or green with one or more yellow stripes Correct answer.

    Explanation

    Section 250.119 requires insulated equipment grounding conductors 6 AWG and smaller to be green or green with one or more yellow stripes. Conductors larger than 6 AWG may instead be identified by green marking or stripping at each termination.

  56. Question 56Grounding, Bonding, and Ground-Fault Protection

    Where is the main bonding jumper installed?

    1. At the meter socket only
    2. At the grounding electrode
    3. In the service equipment enclosure Correct answer.
    4. At each panelboard on the load side of the service

    Explanation

    Section 250.28 requires the main bonding jumper, which connects the grounded circuit conductor to the equipment grounding conductor bus, to be installed in the service equipment enclosure. This connection establishes the low-impedance fault-current path back to the source.

  57. Question 57Grounding, Bonding, and Ground-Fault Protection

    The grounding electrode conductor run to a single ground rod is not required to be larger than:

    1. 1/0 AWG copper
    2. 6 AWG copper Correct answer.
    3. 4 AWG copper
    4. 2 AWG copper

    Explanation

    Section 250.66(A) caps the required grounding electrode conductor for a single rod, pipe, or plate electrode at 6 AWG copper or 4 AWG aluminum, regardless of the service conductor size. A larger grounding electrode conductor is permitted but never required.

  58. Question 58Grounding, Bonding, and Ground-Fault Protection

    A single ground rod is driven and measures 40 ohms to earth. What does the NEC require?

    1. Install a larger-diameter rod of the same length
    2. No further action, because 40 ohms is acceptable
    3. Drive and bond a second rod at least 6 ft away Correct answer.
    4. Increase the grounding electrode conductor to 2 AWG copper

    Explanation

    A single rod, pipe, or plate electrode satisfies the code only where it has a resistance to earth of 25 ohms or less; otherwise it must be supplemented by an additional electrode as required by 250.53(A)(2). Section 250.53(A)(3) requires the supplemental electrode to be at least 6 ft from the first.

  59. Question 59Grounding, Bonding, and Ground-Fault Protection

    What is the minimum-size copper equipment grounding conductor for a 100-ampere feeder?

    1. 4 AWG
    2. 6 AWG
    3. 8 AWG Correct answer.
    4. 10 AWG

    Explanation

    Table 250.122 lists 8 AWG copper as the minimum equipment grounding conductor for circuits protected at 100 amperes. The size is based on the rating of the overcurrent device ahead of the feeder rather than on the size of the feeder conductors.

  60. Question 60Grounding, Bonding, and Ground-Fault Protection

    When a metal underground water pipe is used as a grounding electrode, the NEC requires that it be:

    1. Bonded to the grounded conductor only at the water heater
    2. Used as the only electrode if it is 10 ft in contact with earth
    3. Supplemented by at least one additional electrode Correct answer.
    4. Replaced by a ground ring where the water meter is inside

    Explanation

    Section 250.53(D)(2) requires a metal underground water pipe electrode to be supplemented by at least one other electrode because the pipe can be disconnected or replaced. The supplemental electrode must be bonded to the water pipe electrode, the grounding electrode conductor, the service neutral, or the equipment grounding conductor.

  61. Question 61Grounding, Bonding, and Ground-Fault Protection

    Ground-fault protection of equipment is required for a solidly grounded 480Y/277-volt service rated 1200 amperes. What is the maximum ground-fault current setting permitted?

    1. 800 A
    2. 1200 A Correct answer.
    3. 400 A
    4. 2000 A

    Explanation

    Section 230.95 requires ground-fault protection for solidly grounded wye services of more than 150 volts to ground and 1000 amperes or more. The ground-fault current setting may not exceed 1200 amperes, and an intentional time delay is required to coordinate with downstream protective devices.

  62. Question 62Grounding, Bonding, and Ground-Fault Protection

    Which of the following is permitted as a concrete-encased grounding electrode?

    1. 20 ft of 6 AWG copper in PVC conduit
    2. 20 ft of 1/2-inch reinforcing steel Correct answer.
    3. 10 ft of 3/4-inch galvanized pipe
    4. 8 ft of 5/8-inch ground rod

    Explanation

    Section 250.52(A)(3) recognizes at least 20 ft of 1/2-inch or larger reinforcing steel, or at least 20 ft of bare 4 AWG copper conductor, encased in at least 2 inches of concrete that is in direct contact with the earth. Shorter lengths or smaller conductors do not qualify.

  63. Question 63Grounding, Bonding, and Ground-Fault Protection

    A ground ring electrode must consist of at least 20 ft of bare copper conductor not smaller than 2 AWG that is:

    1. Encased in at least 2 inches of concrete
    2. Buried at least 1 ft below grade
    3. Driven vertically at least 8 ft into the earth
    4. Buried at least 2.5 ft below grade Correct answer.

    Explanation

    Section 250.52(A)(4) defines a ground ring as at least 20 ft of bare copper conductor not smaller than 2 AWG buried at least 2.5 ft below grade. The ring encircles the building or structure it serves.

  64. Question 64Grounding, Bonding, and Ground-Fault Protection

    Metal water piping in a building is bonded to the service equipment enclosure. The bonding jumper must be sized from which table, and on what basis?

    1. Table 250.102(C)(1), using the largest service conductor
    2. Table 250.122, using the rating of the feeder overcurrent device Correct answer.
    3. Table 250.66, using the largest ungrounded service conductor
    4. Table 310.16, using the ampacity of the water pipe

    Explanation

    Section 250.104(A)(1) requires the bonding jumper for a metal water piping system to be sized from Table 250.122 based on the rating of the overcurrent device protecting the service or feeder conductors. Bonding ensures the piping cannot become energized and provides a fault-current path back to the source.

  65. Question 65Grounding, Bonding, and Ground-Fault Protection

    Flexible metal conduit may serve as an equipment grounding conductor where the circuit conductors are protected at not more than ___ and the conduit length is not more than ___.

    1. 30 A; 10 ft
    2. 60 A; 25 ft
    3. 20 A; 6 ft Correct answer.
    4. 15 A; 3 ft

    Explanation

    Section 250.118(5) permits flexible metal conduit to serve as an equipment grounding conductor only where the circuit is protected at 20 amperes or less, the conduit is not longer than 6 ft, listed fittings are used, and the conduit is not relied on as a second fault path.

  66. Question 66Grounding, Bonding, and Ground-Fault Protection

    A separate building is supplied by a feeder that contains an equipment grounding conductor. At the separate building, the grounded circuit conductor must be:

    1. Connected to the metal water piping only
    2. Run without any equipment grounding conductor
    3. Isolated from the grounding electrode system Correct answer.
    4. Bonded to the grounding electrode at that building

    Explanation

    Where an equipment grounding conductor is run with the feeder, Section 250.32(B)(1) prohibits connecting the grounded conductor to the grounding electrode at the separate building. Re-grounding the neutral would place load current on grounding and enclosure paths, creating objectionable current, though a grounding electrode is still required by 250.32(A).

  67. Question 67Grounding, Bonding, and Ground-Fault Protection

    Two parallel runs of PVC conduit supply a 600-ampere feeder. How must the equipment grounding conductors be installed?

    1. An equipment grounding conductor at 50 percent size in each raceway
    2. One full-size equipment grounding conductor in a single raceway
    3. No equipment grounding conductor, because the runs are parallel
    4. A full-size equipment grounding conductor in each raceway Correct answer.

    Explanation

    Section 250.122(F) requires a full-size equipment grounding conductor in each raceway or cable where the circuit conductors are run in parallel. Each conductor is sized from Table 250.122 using the rating of the feeder overcurrent device.

  68. Question 68Grounding, Bonding, and Ground-Fault Protection

    The 6 AWG ungrounded conductors of a 60-ampere circuit are increased to 2 AWG to reduce voltage drop. What must happen to the equipment grounding conductor?

    1. Increased in size in proportion to the ungrounded conductors Correct answer.
    2. Left at 10 AWG, because the overcurrent device rating has not changed at all
    3. Kept at 10 AWG if the circuit is less than 100 ft long
    4. Replaced with a grounding electrode conductor

    Explanation

    Section 250.122(B) requires the equipment grounding conductor to be increased in size proportionally to the increase in circular mil area of the ungrounded conductors when those conductors are upsized for reasons such as voltage drop. For this circuit the proportional calculation raises the grounding conductor from 10 AWG to 6 AWG copper.

  69. Question 69Grounding, Bonding, and Ground-Fault Protection

    Except for separately derived systems, how must the grounded circuit conductor be treated on the load side of the service disconnecting means?

    1. Grounded whenever the feeder is longer than 100 ft
    2. Grounded at each panelboard for redundancy
    3. Grounded at the farthest outlet of the circuit
    4. Not re-grounded, to prevent objectionable current Correct answer.

    Explanation

    Section 250.24(A)(5) prohibits connecting the grounded conductor to any grounding electrode conductor or equipment grounding conductor on the load side of the service disconnecting means. Such a connection would place normal load current on grounding and enclosure paths, creating shock and fire hazards.

  70. Question 70Grounding, Bonding, and Ground-Fault Protection

    The largest ungrounded service-entrance conductor for a service is 500 kcmil copper. What minimum-size copper grounding electrode conductor is required?

    1. 3/0 AWG
    2. 2 AWG
    3. 2/0 AWG
    4. 1/0 AWG Correct answer.

    Explanation

    Table 250.66 requires a 1/0 AWG copper grounding electrode conductor where the largest ungrounded service-entrance conductor is over 350 kcmil through 600 kcmil. The conductor is sized from the service conductors because it must carry fault current between the service and the grounding electrode.

  71. Question 71Grounding, Bonding, and Ground-Fault Protection

    How does a ground-fault circuit interrupter differ from ground-fault protection of equipment?

    1. Both devices trip at 5 mA, but GFP includes an intentional time delay
    2. A GFCI protects people at low currents; GFP protects equipment at higher currents Correct answer.
    3. A GFCI protects equipment from arcing, while GFP protects people from electric shock
    4. A GFCI is required only on solidly grounded 480Y/277-volt services

    Explanation

    A Class A GFCI trips at approximately 5 mA to protect people from electric shock, while ground-fault protection of equipment responds to much higher ground-fault currents and uses a time delay for coordination. Ground-fault protection of equipment is required for large solidly grounded wye services by Section 230.95.

  72. Question 72Grounding, Bonding, and Ground-Fault Protection

    A building has a metal underground water pipe, a concrete-encased electrode, and a ground ring available. What does the NEC require?

    1. All electrodes present must be bonded together into one system Correct answer.
    2. The water pipe plus one of the other electrodes must be used
    3. Only the electrode with the lowest resistance to earth is required to be used
    4. Only the metal underground water pipe is required to be used

    Explanation

    Section 250.50 requires all of the electrodes described in 250.52(A)(1) through (A)(7) that are present at a building to be bonded together to form a single grounding electrode system. The water pipe electrode must also be supplemented as required by 250.53(D)(2).

  73. Question 73Grounding, Bonding, and Ground-Fault Protection

    A dry-type transformer with a 480-volt primary and a 208Y/120-volt secondary is installed as a separately derived system. What grounding and bonding must be provided at the transformer?

    1. A neutral disconnect link and a main bonding jumper at the first panelboard
    2. A ground-fault relay set at 1200 amperes
    3. Only a grounding electrode conductor, because the primary equipment grounding conductor provides the bond
    4. A system bonding jumper and a grounding electrode conductor to an electrode Correct answer.

    Explanation

    Section 250.30 requires a separately derived system to have a system bonding jumper connecting the grounded conductor to the equipment grounding conductor and a grounding electrode conductor connected to a grounding electrode at the source. The equipment grounding conductor of the primary circuit does not perform this function for the new system.

  74. Question 74Grounding, Bonding, and Ground-Fault Protection

    Grounding electrode conductor splices or joints are permitted only where they are:

    1. Made in an accessible junction box with listed wire connectors
    2. Approved by the serving utility and buried
    3. Made with split-bolt connectors and taped
    4. Made by irreversible compression or exothermic welding Correct answer.

    Explanation

    Section 250.64(C) requires the grounding electrode conductor to be run in one continuous length without a splice or joint, except for splices made by irreversible compression-type connectors listed for grounding and bonding or by exothermic welding. These methods maintain a permanent, low-resistance connection.

  75. Question 75Overcurrent Protection and Short-Circuit Current Ratings

    Which of the following is a standard ampere rating for an overcurrent protective device?

    1. 65 A
    2. 60 A Correct answer.
    3. 75 A
    4. 55 A

    Explanation

    NEC 240.6(A) lists the standard ampere ratings for fuses and fixed-trip circuit breakers, and 60 A is one of them. The list runs 50 A, 60 A, 70 A, 80 A, 90 A, 100 A, and so on, so values such as 55 A, 65 A, and 75 A are not standard ratings.

  76. Question 76Overcurrent Protection and Short-Circuit Current Ratings

    An overcurrent protective device must have an interrupting rating that is ____ the current available at its line terminals.

    1. equal to or greater than Correct answer.
    2. equal to or less than
    3. within 10 percent of
    4. at least 75 percent of

    Explanation

    NEC 110.9 requires equipment intended to break current to have an interrupting rating sufficient for the nominal circuit voltage and the current that is available at the line terminals of the equipment. A device applied where the available fault current exceeds its interrupting rating may fail catastrophically.

  77. Question 77Overcurrent Protection and Short-Circuit Current Ratings

    The general limit on overcurrent protection for a 14 AWG copper branch-circuit conductor is ____.

    1. 12 A
    2. 10 A
    3. 20 A
    4. 15 A Correct answer.

    Explanation

    NEC 240.4(D) sets general limitations on overcurrent protection for small conductors, and 14 AWG copper is limited to a 15 A device unless a specific section permits otherwise. Larger devices on 14 AWG are allowed only in the narrow cases the Code recognizes, such as certain motor circuits.

  78. Question 78Overcurrent Protection and Short-Circuit Current Ratings

    As defined in the NEC, the term overcurrent includes current in excess of the rated current of equipment or the ampacity of a conductor that results from ____.

    1. a ground fault only
    2. overloads, short circuits, and ground faults Correct answer.
    3. a short circuit only
    4. an overload only

    Explanation

    The Article 100 definition of overcurrent covers any current above the rating of the equipment or the ampacity of the conductor. The definition states that overcurrent may result from overload, short circuit, or ground fault, which is why Article 240 addresses all three conditions.

  79. Question 79Overcurrent Protection and Short-Circuit Current Ratings

    In a motor branch circuit, the primary purpose of the overload protective device is to ____.

    1. clear ground faults at the motor terminals
    2. interrupt short-circuit current within the motor controller
    3. protect the motor and branch-circuit conductors from dangerous overheating caused by overload Correct answer.
    4. establish the interrupting rating of the branch circuit

    Explanation

    Overload protection required by Article 430, Part III protects the motor and its branch-circuit conductors against overheating from excessive current that is below short-circuit levels. Short-circuit and ground-fault protection is a separate requirement under 430.52 and is provided by the branch-circuit overcurrent device.

  80. Question 80Overcurrent Protection and Short-Circuit Current Ratings

    A branch-circuit conductor has an ampacity of 65 A, which does not correspond to a standard overcurrent device rating. Under what condition may the next higher standard rating of 70 A be used?

    1. Only when the conductor is 8 AWG or larger
    2. When the circuit is protected by fuses rather than a circuit breaker
    3. When the circuit does not supply a multioutlet receptacle branch circuit and the rating does not exceed 800 A Correct answer.
    4. Only when the branch circuit supplies a single continuous load

    Explanation

    NEC 240.4(B) permits rounding up to the next higher standard rating when the conductor ampacity does not correspond to a standard rating, the device does not exceed 800 A, and the conductors do not supply a multioutlet receptacle branch circuit. All of the listed conditions must be satisfied.

  81. Question 81Overcurrent Protection and Short-Circuit Current Ratings

    Under the 25 ft feeder tap rule, the ampacity of the tap conductors must be not less than ____ of the rating of the overcurrent device protecting the feeder.

    1. two-thirds
    2. one-tenth
    3. one-half
    4. one-third Correct answer.

    Explanation

    NEC 240.21(B)(2) permits taps up to 25 ft long where the tap conductor ampacity is at least one-third of the rating of the overcurrent device protecting the feeder. The rule also requires the tap to terminate in a single overcurrent device and to be protected from physical damage.

  82. Question 82Overcurrent Protection and Short-Circuit Current Ratings

    A 45 kVA dry-type transformer is served at 480 V three-phase and has a primary full-load current of 54 A. Primary-only overcurrent protection is used. What is the maximum standard rating permitted for the primary overcurrent device?

    1. 70 A Correct answer.
    2. 80 A
    3. 90 A
    4. 60 A

    Explanation

    Table 450.3(B) allows primary-only protection at 125 percent of the primary full-load current for transformers with a primary current of 9 A or more. Here 125 percent of 54 A is 67.5 A, and where that value does not correspond to a standard rating, the table's notes permit the next higher standard rating of 70 A.

  83. Question 83Overcurrent Protection and Short-Circuit Current Ratings

    Ground-fault protection of equipment is required for a solidly grounded wye service disconnect, more than 150 V to ground but not over 600 V phase-to-phase, when the disconnect is rated ____ or more.

    1. 600 A
    2. 1000 A Correct answer.
    3. 800 A
    4. 1200 A

    Explanation

    NEC 230.95 requires ground-fault protection of equipment for solidly grounded wye services above 150 V to ground but not exceeding 600 V phase-to-phase where the service disconnect is rated 1000 A or more. The sensing system may be set to pick up at no more than 1200 A and must clear a 3000 A ground fault within 1 second.

  84. Question 84Overcurrent Protection and Short-Circuit Current Ratings

    An overcurrent protective device is considered current limiting when, in its current-limiting range, it ____.

    1. reduces the current let through to substantially less than would flow through a comparable solid conductor Correct answer.
    2. holds its continuous current to 80 percent of its rating
    3. opens within 10 seconds of fault inception
    4. coordinates with the next upstream device at every fault level

    Explanation

    The Article 100 definition compares the device to a solid conductor of comparable impedance: a current-limiting device cuts off the fault current in its current-limiting range so that the let-through current is substantially less. This behavior is what makes listed series combinations and component protection possible.

  85. Question 85Overcurrent Protection and Short-Circuit Current Ratings

    The maximum rating of an inverse-time circuit breaker used for short-circuit and ground-fault protection of a single-phase motor branch circuit is ____ of the motor full-load current.

    1. 200 percent
    2. 250 percent Correct answer.
    3. 300 percent
    4. 175 percent

    Explanation

    Table 430.52 sets the inverse-time circuit breaker at 250 percent of the motor full-load current for a standard motor branch circuit. The other table values apply to other device types, such as 175 percent for a dual-element time-delay fuse and 300 percent for a non-time-delay fuse.

  86. Question 86Overcurrent Protection and Short-Circuit Current Ratings

    For a 480Y/277 V service on a commercial building, the available fault current must be ____.

    1. calculated and retained in the project file only
    2. reported to the serving utility before the transformer is set
    3. field-marked at the service equipment with a permanent label showing the date of calculation Correct answer.
    4. submitted to the authority having jurisdiction before energization only

    Explanation

    NEC 110.24(A) requires the available fault current at service equipment of other than dwelling units to be field marked with a durable legended label at the service equipment, including the date the calculation was performed. Section 110.24(B) requires the marking to be updated when a modification changes the available fault current.

  87. Question 87Overcurrent Protection and Short-Circuit Current Ratings

    A panelboard is marked with a short-circuit current rating of 10 kA. The available fault current at its terminals is 18 kA, and each branch circuit breaker installed in it is individually marked 22 kAIC. What does the Code require?

    1. The installation is acceptable if the panelboard's main breaker is also rated 22 kAIC.
    2. The panelboard's marked assembly rating governs, so the installation is not acceptable as is. Correct answer.
    3. The installation is acceptable because each branch breaker is rated 22 kAIC, which exceeds the 18 kA available.
    4. The installation is acceptable if the panelboard is located within 10 ft of the service equipment.

    Explanation

    Equipment such as a panelboard must be applied so that the available fault current at its terminals does not exceed its marked short-circuit current rating. Individual branch devices with higher interrupting ratings do not raise the rating of the assembly; a higher rated assembly or a listed series-rated combination would be required.

  88. Question 88Overcurrent Protection and Short-Circuit Current Ratings

    A feeder circuit breaker marked with an interrupting rating of 22 kA is installed where 40 kA of fault current is available at its line terminals. Which of the following makes the installation acceptable?

    1. Using the breaker as part of a listed series-rated combination with an upstream current-limiting device, with the equipment marked for the series rating. Correct answer.
    2. Installing current-limiting fuses ahead of the breaker even though the combination is not listed.
    3. Nothing further is required, because interrupting rating follows the breaker frame size.
    4. Replacing the breaker with a larger frame size that carries the same 22 kA interrupting rating.

    Explanation

    NEC 240.86 permits a series-rated installation only where the combination of the upstream device and the load-side device has been tested and listed, the equipment is marked with the series rating, and the conditions of the listing are maintained. Field-assembled combinations that are not listed cannot be used to exceed the interrupting rating of the load-side device.

  89. Question 89Overcurrent Protection and Short-Circuit Current Ratings

    Which overcurrent protective devices must be selectively coordinated in an emergency system?

    1. Only the devices in generator-supplied emergency systems, not those in separate emergency services
    2. Only the ground-fault protective devices in the emergency distribution equipment
    3. Every overcurrent device in the emergency system, coordinated with all supply-side overcurrent devices Correct answer.
    4. Only the service main device, coordinated with the utility overcurrent protection

    Explanation

    NEC 700.32 requires the overcurrent devices of an emergency system to be selectively coordinated with all supply-side overcurrent protective devices. Selective coordination localizes a fault so that an upstream device does not open and take out equipment that is intended to remain energized.

  90. Question 90Overcurrent Protection and Short-Circuit Current Ratings

    A 460 V, 40 hp motor has a full-load current of 52 A. An inverse-time circuit breaker rated 130 A, the 250 percent value, trips during motor acceleration. What is the maximum rating to which that breaker may be increased?

    1. 260 A
    2. 175 A
    3. 208 A Correct answer.
    4. 190 A

    Explanation

    Where the Table 430.52 value is not sufficient for starting current, the exception permits the rating to be increased but not beyond 400 percent of the motor full-load current for an inverse-time circuit breaker. Four hundred percent of 52 A is 208 A, so that is the ceiling regardless of how the trip persists above it.

  91. Question 91Branch Circuits, Feeders, and Service Load Calculations

    For a one-family dwelling, what general lighting load per square foot is used in a service calculation?

    1. 5 VA per square foot
    2. 3 VA per square foot Correct answer.
    3. 2 VA per square foot
    4. 1 VA per square foot

    Explanation

    NEC Table 220.12 assigns a general lighting load of 3 VA per square foot for dwelling units. This value is used before demand factors are applied.

  92. Question 92Branch Circuits, Feeders, and Service Load Calculations

    What is the minimum number of 20-ampere small-appliance branch circuits required for a dwelling unit kitchen?

    1. Two Correct answer.
    2. Three
    3. Four
    4. One

    Explanation

    NEC 210.11(C)(1) requires at least two 20-ampere small-appliance branch circuits for kitchen and related countertop receptacles. Additional circuits may be installed but are not the minimum.

  93. Question 93Branch Circuits, Feeders, and Service Load Calculations

    What is the minimum rating of a branch circuit that supplies bathroom receptacle outlets in a dwelling unit?

    1. 20 amperes Correct answer.
    2. 30 amperes
    3. 15 amperes
    4. 40 amperes

    Explanation

    NEC 210.11(C)(3) requires at least one 20-ampere branch circuit to supply bathroom receptacle outlets. The circuit must be sized for the receptacle load and not less than 20 amperes.

  94. Question 94Branch Circuits, Feeders, and Service Load Calculations

    In a dwelling unit, what is the maximum distance from any point along a wall to a receptacle outlet in the required general receptacle spacing?

    1. 4 feet
    2. 6 feet Correct answer.
    3. 2 feet
    4. 5 feet

    Explanation

    NEC 210.52(A)(1) requires receptacle outlets so that no point along the floor line is more than 6 feet from a receptacle. This spacing limits the use of extension cords.

  95. Question 95Branch Circuits, Feeders, and Service Load Calculations

    What is the minimum rating of the branch circuit required for laundry receptacle outlets in a dwelling unit?

    1. 30 amperes
    2. 20 amperes Correct answer.
    3. 15 amperes
    4. 40 amperes

    Explanation

    NEC 210.11(C)(2) requires at least one 20-ampere branch circuit for laundry receptacle outlets. This circuit supplies the laundry area receptacles.

  96. Question 96Branch Circuits, Feeders, and Service Load Calculations

    A branch circuit supplies a 16-ampere continuous load and a 10-ampere noncontinuous load. What is the minimum overcurrent device rating?

    1. 30 amperes Correct answer.
    2. 25 amperes
    3. 35 amperes
    4. 40 amperes

    Explanation

    NEC 210.20(A) requires the overcurrent device to be at least 125 percent of the continuous load plus 100 percent of the noncontinuous load. The calculation is 16 × 1.25 + 10 = 30 amperes.

  97. Question 97Branch Circuits, Feeders, and Service Load Calculations

    Which dwelling-unit location requires GFCI protection for its receptacles?

    1. Hallway
    2. Living room
    3. Bedroom
    4. Kitchen countertop Correct answer.

    Explanation

    NEC 210.8(A) requires GFCI protection for receptacles serving kitchen countertop surfaces in dwelling units. This protection reduces shock hazard near sinks and wet areas.

  98. Question 98Branch Circuits, Feeders, and Service Load Calculations

    What is the minimum copper conductor size permitted for a 20-ampere branch circuit?

    1. 14 AWG
    2. 12 AWG Correct answer.
    3. 10 AWG
    4. 8 AWG

    Explanation

    NEC 240.4(D) limits 14 AWG copper to 15-ampere overcurrent protection. A 20-ampere branch circuit therefore requires at least 12 AWG copper.

  99. Question 99Branch Circuits, Feeders, and Service Load Calculations

    In a dwelling-unit service calculation, what demand factor applies to the first 3,000 VA of the general lighting load?

    1. 50 percent
    2. 35 percent
    3. 25 percent
    4. 100 percent Correct answer.

    Explanation

    NEC Table 220.42 applies 100 percent to the first 3,000 VA of the dwelling general lighting load. The remaining portions receive lower demand factors.

  100. Question 100Branch Circuits, Feeders, and Service Load Calculations

    Three 20-ampere small-appliance branch circuits are used in a dwelling calculation. What total load is assigned to these circuits before demand factors?

    1. 6,000 VA
    2. 7,500 VA
    3. 4,500 VA Correct answer.
    4. 3,000 VA

    Explanation

    NEC 220.52(A) assigns 1,500 VA to each 20-ampere small-appliance branch circuit. Three circuits therefore contribute 3 × 1,500 = 4,500 VA.

  101. Question 101Branch Circuits, Feeders, and Service Load Calculations

    What load is assigned to the required laundry branch circuit in a dwelling-unit calculation?

    1. 1,000 VA
    2. 1,500 VA Correct answer.
    3. 2,000 VA
    4. 1,200 VA

    Explanation

    NEC 220.52(B) assigns 1,500 VA to the required laundry branch circuit. This load is included in the feeder and service calculation.

  102. Question 102Branch Circuits, Feeders, and Service Load Calculations

    A dwelling unit has 2,000 square feet of floor area. Using the general lighting load of 3 VA per square foot, what is the general lighting load before demand factors?

    1. 4,000 VA
    2. 5,000 VA
    3. 6,000 VA Correct answer.
    4. 5,500 VA

    Explanation

    The general lighting load equals area times 3 VA per square foot. For 2,000 square feet, 2,000 × 3 = 6,000 VA.

  103. Question 103Branch Circuits, Feeders, and Service Load Calculations

    A 20-ampere small-appliance branch circuit supplies cord-and-plug connected loads. What is the maximum load permitted on the circuit?

    1. 15 amperes
    2. 12 amperes
    3. 20 amperes
    4. 16 amperes Correct answer.

    Explanation

    NEC 210.23(A)(1) limits a 20-ampere branch circuit supplying cord-and-plug connected loads to 80 percent of the circuit rating. The maximum is 20 × 0.80 = 16 amperes.

  104. Question 104Branch Circuits, Feeders, and Service Load Calculations

    A household electric clothes dryer has a nameplate rating of 4,500 watts. What minimum load is used for this dryer in a dwelling service calculation?

    1. 6,000 VA
    2. 5,000 VA Correct answer.
    3. 4,500 VA
    4. 5,500 VA

    Explanation

    NEC 220.54 requires household electric clothes dryers to be calculated at 5,000 VA or the nameplate rating, whichever is larger. Since 5,000 VA is larger than 4,500 VA, 5,000 VA is used.

  105. Question 105Branch Circuits, Feeders, and Service Load Calculations

    A feeder supplies a 40-ampere continuous load and a 20-ampere noncontinuous load. What is the minimum feeder conductor ampacity?

    1. 65 amperes
    2. 60 amperes
    3. 70 amperes Correct answer.
    4. 80 amperes

    Explanation

    NEC 215.2(A)(1) requires feeder conductors to have an ampacity of at least 125 percent of the continuous load plus 100 percent of the noncontinuous load. The calculation is 40 × 1.25 + 20 = 70 amperes.

  106. Question 106Branch Circuits, Feeders, and Service Load Calculations

    A dwelling service has a calculated load of 180 amperes. What is the minimum standard rating of the service disconnecting means?

    1. 150 amperes
    2. 175 amperes
    3. 180 amperes
    4. 200 amperes Correct answer.

    Explanation

    NEC 240.6 lists standard ampere ratings, and the service disconnecting means must have a rating not less than the calculated load. The next standard rating above 180 amperes is 200 amperes.

  107. Question 107Branch Circuits, Feeders, and Service Load Calculations

    What is the generally recommended maximum voltage drop for a branch circuit?

    1. 2 percent
    2. 10 percent
    3. 3 percent Correct answer.
    4. 5 percent

    Explanation

    NEC 210.19(A) informational notes recommend a maximum branch-circuit voltage drop of 3 percent. The feeder plus branch circuit is generally recommended not to exceed 5 percent total.

  108. Question 108Branch Circuits, Feeders, and Service Load Calculations

    Which device provides both arc-fault and ground-fault protection for a dwelling branch circuit?

    1. Standard thermal-magnetic breaker
    2. Dual-function circuit breaker Correct answer.
    3. GFCI receptacle
    4. Isolated ground receptacle

    Explanation

    A dual-function circuit breaker combines AFCI and GFCI protection in one overcurrent device. This is useful where both types of protection are required for the same branch circuit.

  109. Question 109Branch Circuits, Feeders, and Service Load Calculations

    A 120/240-volt single-phase dwelling service has a calculated load of 150 amperes. What minimum size copper THWN service-entrance conductor is required at 75°C?

    1. 1 AWG
    2. 2/0 AWG
    3. 1/0 AWG Correct answer.
    4. 2 AWG

    Explanation

    Using the 75°C copper column of Table 310.16, 1/0 AWG has an ampacity of 150 amperes. The conductor must have an ampacity at least equal to the 150-ampere calculated load.

  110. Question 110Branch Circuits, Feeders, and Service Load Calculations

    Using Table 220.55, what demand factor applies to the calculated load for four household electric ranges in a multifamily dwelling?

    1. 70 percent
    2. 80 percent
    3. 45 percent Correct answer.
    4. 55 percent

    Explanation

    NEC Table 220.55 permits a 45 percent demand factor for four household electric ranges. The table reduces the range load as the number of ranges increases.

  111. Question 111Branch Circuits, Feeders, and Service Load Calculations

    A 2,400-square-foot dwelling has two small-appliance circuits and one laundry circuit. What is the general lighting, small-appliance, and laundry load after applying the dwelling demand factors?

    1. 5,700 VA
    2. 4,500 VA
    3. 7,200 VA
    4. 6,045 VA Correct answer.

    Explanation

    The connected load is 2,400 × 3 = 7,200 VA for lighting, plus 3,000 VA for small appliances, plus 1,500 VA for laundry, totaling 11,700 VA. The first 3,000 VA is at 100 percent, and the remaining 8,700 VA is at 35 percent, giving 3,000 + 3,045 = 6,045 VA.

  112. Question 112Branch Circuits, Feeders, and Service Load Calculations

    A dwelling has one 12-kilowatt electric range. Using Table 220.55 Column C, what demand load is used for this range?

    1. 8 kW Correct answer.
    2. 12 kW
    3. 10 kW
    4. 6 kW

    Explanation

    NEC Table 220.55 Column C permits a maximum demand load of 8 kW for one 12-kilowatt range. The table value may be used instead of the nameplate rating.

  113. Question 113Branch Circuits, Feeders, and Service Load Calculations

    A 120/240-volt feeder supplies a 10-kilowatt range and a 5-kilowatt dryer. Using the permitted 70 percent neutral calculation, what neutral load is used?

    1. 7.5 kW
    2. 12 kW
    3. 10.5 kW Correct answer.
    4. 15 kW

    Explanation

    NEC 220.61(C)(1) permits the neutral load for electric ranges and dryers on 3-wire circuits to be calculated at 70 percent of the ungrounded-conductor load. The combined load is 15 kW, and 15 × 0.70 = 10.5 kW.

  114. Question 114Branch Circuits, Feeders, and Service Load Calculations

    A 200-ampere dwelling service has a calculated neutral load of 250 amperes. If the neutral load may be reduced by 70 percent for the portion exceeding 200 amperes, what is the adjusted neutral load?

    1. 225 A
    2. 235 A Correct answer.
    3. 250 A
    4. 215 A

    Explanation

    The first 200 amperes are taken at 100 percent, and the 50 amperes above 200 are taken at 70 percent. Thus 200 + (50 × 0.70) = 235 amperes.

  115. Question 115Branch Circuits, Feeders, and Service Load Calculations

    A multifamily dwelling has six dwelling units, each with a 40-ampere calculated load. Using the optional method demand factor of 44 percent, what is the service demand load?

    1. 120 A
    2. 144 A
    3. 105.6 A Correct answer.
    4. 96 A

    Explanation

    The total connected load is 6 × 40 = 240 amperes. Applying the 44 percent demand factor for six units gives 240 × 0.44 = 105.6 amperes.

  116. Question 116Branch Circuits, Feeders, and Service Load Calculations

    In a dwelling unit, what is the maximum permitted distance along the floor line of a wall from any point to the nearest receptacle outlet?

    1. 4 feet
    2. 12 feet
    3. 8 feet
    4. 6 feet Correct answer.

    Explanation

    NEC 210.52(A)(1) requires receptacle outlets in dwelling unit rooms so that no point along the floor line of any wall space is more than 6 feet from a receptacle. This 6-foot measurement controls how far a point on the wall can be from the nearest outlet, which is different from the maximum spacing allowed between outlets.

  117. Question 117Branch Circuits, Feeders, and Service Load Calculations

    What is the maximum rating of the overcurrent device permitted to protect a 14 AWG copper branch-circuit conductor?

    1. 15 amperes Correct answer.
    2. 30 amperes
    3. 25 amperes
    4. 20 amperes

    Explanation

    NEC 240.4(D) limits the overcurrent protection for 14 AWG copper conductors to 15 amperes unless a specific exception applies. This protection limit is what generally establishes 14 AWG as the minimum size for a 15-ampere branch circuit.

  118. Question 118Branch Circuits, Feeders, and Service Load Calculations

    A dwelling unit has five appliances fastened in place, each rated 1,500 volt-amperes. Under the standard calculation method, what total load is assigned to these appliances in the service calculation?

    1. 3,750 volt-amperes
    2. 6,000 volt-amperes
    3. 7,500 volt-amperes
    4. 5,625 volt-amperes Correct answer.

    Explanation

    NEC 220.53 permits a demand factor of 75 percent to be applied to the nameplate rating of four or more appliances fastened in place, excluding ranges, dryers, air-conditioning equipment, and space heating. The connected load is 5 × 1,500 = 7,500 volt-amperes, and 75 percent of that value is 5,625 volt-amperes.

  119. Question 119Branch Circuits, Feeders, and Service Load Calculations

    A dwelling unit has a 12-kilowatt electric space-heating load and a 9-kilowatt air-conditioning load. How are these two loads handled in the standard service calculation?

    1. Use the larger load at 100 percent Correct answer.
    2. Use the heating load at 65 percent
    3. Use the air-conditioning load only
    4. Add both loads together at 100 percent

    Explanation

    NEC 220.60 permits the larger of the noncoincident heating and air-conditioning loads to be used, rather than summing them, because the equipment does not operate at the same time. The larger load here is the 12-kilowatt heating load, taken at 100 percent.

  120. Question 120Branch Circuits, Feeders, and Service Load Calculations

    Using the optional method for a single dwelling unit, the general lighting, small-appliance, laundry, and other general loads total 14,000 volt-amperes. What load value is used for these loads?

    1. 10,000 volt-amperes
    2. 11,600 volt-amperes Correct answer.
    3. 14,000 volt-amperes
    4. 15,600 volt-amperes

    Explanation

    Under NEC 220.82(B), the optional method takes 100 percent of the first 10,000 volt-amperes of these loads plus 40 percent of the remainder. The remainder is 4,000 volt-amperes, so 40 percent of it is 1,600 volt-amperes, giving 10,000 + 1,600 = 11,600 volt-amperes.

  121. Question 121Conductors, Cables, Ampacities, and Derating

    Using the 75°C column of Table 310.16, what is the allowable ampacity of 12 AWG copper THHN conductor?

    1. 25 A Correct answer.
    2. 30 A
    3. 20 A
    4. 35 A

    Explanation

    Table 310.16 lists 12 AWG copper at 25 A in the 75°C column. The 30 A value in the 90°C column applies only where the conductor's ampacity is not limited by termination ratings or other equipment.

  122. Question 122Conductors, Cables, Ampacities, and Derating

    Unless the conductor's ampacity is limited by terminations, from which temperature column of Table 310.16 is the ampacity of 10 AWG copper NM-B cable taken?

    1. 90°C column
    2. 75°C column
    3. the column matching the insulation
    4. 60°C column Correct answer.

    Explanation

    Section 334.80 limits the ampacity of conductors in NM, NMC, and NMS cable to that listed in the 60°C column. The 90°C insulation rating may be used only for the derating calculations, not for the final ampacity.

  123. Question 123Conductors, Cables, Ampacities, and Derating

    A conductor with 90°C insulation is installed where the ambient temperature is 40°C. Which correction factor applies to its ampacity?

    1. 0.82
    2. 0.87
    3. 0.91 Correct answer.
    4. 0.96

    Explanation

    Table 310.15(B)(1) gives an ambient correction factor of 0.91 for a 90°C conductor in a 40°C ambient. Ampacities in Table 310.16 are based on 30°C, so higher ambients require correction.

  124. Question 124Conductors, Cables, Ampacities, and Derating

    Four current-carrying conductors are installed in a single raceway. What ampacity adjustment factor from Table 310.15(C)(1) applies?

    1. 70%
    2. 80% Correct answer.
    3. 50%
    4. 75%

    Explanation

    Table 310.15(C)(1) requires an 80% adjustment for four to six current-carrying conductors in a single raceway or cable. Higher conductor counts bring progressively smaller factors.

  125. Question 125Conductors, Cables, Ampacities, and Derating

    What is the maximum overcurrent device rating permitted to protect a 14 AWG copper branch-circuit conductor under the small-conductor rule?

    1. 15 A Correct answer.
    2. 25 A
    3. 30 A
    4. 20 A

    Explanation

    Section 240.4(D) limits 14 AWG copper to a 15 A overcurrent device regardless of its tabulated ampacity. The rule protects small conductors from overcurrent beyond their safe capability.

  126. Question 126Conductors, Cables, Ampacities, and Derating

    What is the maximum temperature rating of THHN insulation in a dry location?

    1. 60°C
    2. 90°C Correct answer.
    3. 75°C
    4. 105°C

    Explanation

    THHN is a 90°C, dry-location, heat-resistant thermoplastic conductor; the 'W' suffix in THWN adds a 75°C wet-location rating. The 90°C rating may be used for derating calculations even when terminations limit the final ampacity.

  127. Question 127Conductors, Cables, Ampacities, and Derating

    A 10 AWG copper THHN conductor has a 90°C ampacity of 40 A. It is installed with five other current-carrying conductors in one raceway at a 40°C ambient. What is the adjusted ampacity?

    1. 29 A Correct answer.
    2. 26 A
    3. 24 A
    4. 32 A

    Explanation

    Apply both factors to the 90°C ampacity: 0.91 for the 40°C ambient and 0.80 for six current-carrying conductors, giving 40 x 0.91 x 0.80 = 29.1 A. The result is rounded down to 29 A.

  128. Question 128Conductors, Cables, Ampacities, and Derating

    Eight current-carrying conductors are pulled into a single conduit. What percentage of the tabulated ampacity is permitted?

    1. 70% Correct answer.
    2. 60%
    3. 50%
    4. 45%

    Explanation

    Table 310.15(C)(1) applies a 70% factor to seven, eight, or nine current-carrying conductors in a single raceway or cable. The factor is applied to the ampacity taken from the appropriate table column.

  129. Question 129Conductors, Cables, Ampacities, and Derating

    A 3-wire, single-phase 120/240 V circuit supplies only line-to-neutral loads. How many current-carrying conductors are counted when applying ampacity adjustment for the two ungrounded conductors and the neutral in one raceway?

    1. Four conductors
    2. Two conductors Correct answer.
    3. Three conductors
    4. One conductor

    Explanation

    A neutral that carries only the unbalanced current of the circuit is not counted as a current-carrying conductor, so only the two ungrounded conductors are counted. The neutral is counted where it carries harmonic current from nonlinear loads.

  130. Question 130Conductors, Cables, Ampacities, and Derating

    A 90°C THHN conductor is terminated on a circuit breaker marked with a 75°C rating. Which temperature rating governs the final ampacity of the conductor?

    1. 60°C, the default equipment rating
    2. 75°C, the breaker terminal rating Correct answer.
    3. 90°C, the conductor insulation rating
    4. 105°C, the conductor overload rating

    Explanation

    Section 110.14(C) requires the ampacity to be based on the lowest temperature rating of any connected termination, conductor, or device. A breaker marked 75°C therefore limits the conductor to the 75°C column even though the insulation is rated 90°C.

  131. Question 131Conductors, Cables, Ampacities, and Derating

    What is the allowable ampacity of 4 AWG aluminum THWN conductor using the 75°C column of Table 310.16?

    1. 75 A
    2. 65 A Correct answer.
    3. 50 A
    4. 55 A

    Explanation

    Table 310.16 lists 4 AWG aluminum at 65 A in the 75°C column. Aluminum carries less current than copper of the same size, so its ampacities are listed separately.

  132. Question 132Conductors, Cables, Ampacities, and Derating

    A conductor has a corrected and adjusted ampacity of 68 A and supplies a single motor branch circuit. What is the largest standard overcurrent device permitted by the next-size-up rule?

    1. 90 A
    2. 60 A
    3. 70 A Correct answer.
    4. 80 A

    Explanation

    Section 240.4(B) allows the next higher standard rating when the ampacity does not match a standard size, provided the rating does not exceed 800 A and the circuit is not a multioutlet receptacle branch circuit. The next standard size above 68 A is 70 A.

  133. Question 133Conductors, Cables, Ampacities, and Derating

    A raceway is installed on a rooftop less than 7/8 in. above the roof surface. For ampacity correction, the ambient temperature used must be which of the following?

    1. Design ambient plus 17°C Correct answer.
    2. No adder applied
    3. The 30°C base ambient
    4. Design ambient minus 17°C

    Explanation

    Section 310.15(B)(2) requires adding 30°F (17°C) to the outdoor design ambient for raceways and cables installed on or above rooftops within 7/8 in. of the surface. The added heat from the roof is accounted for through this adder.

  134. Question 134Conductors, Cables, Ampacities, and Derating

    What is the minimum size copper conductor permitted for a 25 A individual branch circuit?

    1. 10 AWG Correct answer.
    2. 12 AWG
    3. 8 AWG
    4. 14 AWG

    Explanation

    Section 240.4(D) limits 12 AWG copper to a 20 A overcurrent device, so a 25 A circuit requires at least 10 AWG copper, which may be protected up to 30 A. The conductor must also have an ampacity of at least 25 A.

  135. Question 135Conductors, Cables, Ampacities, and Derating

    What is the ampacity of 250 kcmil copper THWN conductor using the 75°C column of Table 310.16?

    1. 250 A
    2. 230 A
    3. 255 A Correct answer.
    4. 240 A

    Explanation

    Table 310.16 lists 250 kcmil copper at 255 A in the 75°C column. The 90°C column value is 290 A and the 60°C column value is 215 A.

  136. Question 136Conductors, Cables, Ampacities, and Derating

    A 4/0 copper THWN conductor with a 90°C ampacity of 260 A is installed in a 50°C ambient. What is its corrected ampacity?

    1. 205 A
    2. 213 A Correct answer.
    3. 190 A
    4. 175 A

    Explanation

    Table 310.15(B)(1) gives a 0.82 factor for a 90°C conductor at 50°C ambient. Multiplying 260 A by 0.82 gives 213.2 A, which is rounded down to 213 A.

  137. Question 137Conductors, Cables, Ampacities, and Derating

    Six 3/0 copper THWN current-carrying conductors are installed in one raceway where the ambient is 40°C. Using the 90°C ampacity of 225 A, what is the adjusted ampacity?

    1. 190 A
    2. 150 A
    3. 163 A Correct answer.
    4. 175 A

    Explanation

    Multiply the 90°C ampacity by both the 0.80 conductor-count factor for six conductors and the 0.91 ambient factor for 40°C: 225 x 0.80 x 0.91 = 163.8 A. The value is rounded down to 163 A.

  138. Question 138Conductors, Cables, Ampacities, and Derating

    A 100 A continuous load is supplied by three current-carrying copper THWN conductors in one raceway in a 40°C ambient, with 75°C terminations. What is the minimum conductor size?

    1. 1/0 AWG
    2. 3/0 AWG
    3. 2/0 AWG
    4. 1 AWG Correct answer.

    Explanation

    The load requires 125 A after the 125% continuous-load factor. A 1 AWG copper conductor has a 90°C ampacity of 150 A; applying the 0.91 ambient factor leaves 136.5 A, and its 75°C ampacity of 130 A also exceeds 125 A. A 2 AWG conductor falls below 125 A after correction.

  139. Question 139Conductors, Cables, Ampacities, and Derating

    Six 4 AWG THWN conductors are pulled through a 20 in. long nipple between two enclosures with fill under 60 percent. What ampacity adjustment is required for the conductor count?

    1. 80% factor
    2. No adjustment required Correct answer.
    3. 50% factor
    4. 70% factor

    Explanation

    Table 310.15(C)(1) does not require adjustment for conductors in a raceway or nipple 24 in. or less in length where the conductors do not occupy more than 60 percent of the raceway area. The 20 in. nipple qualifies for this exception.

  140. Question 140Conductors, Cables, Ampacities, and Derating

    Nine 12 AWG copper THHN current-carrying conductors with a 90°C ampacity of 30 A are installed in one conduit at a 30°C ambient. What is the adjusted ampacity?

    1. 27 A
    2. 24 A
    3. 30 A
    4. 21 A Correct answer.

    Explanation

    Table 310.15(C)(1) requires a 70% factor for seven to nine current-carrying conductors, and no ambient correction is needed at 30°C. Multiplying 30 A by 0.70 gives 21 A, which must then be coordinated with the 20 A limit for 12 AWG in 240.4(D).

  141. Question 141Boxes, Raceways, Panelboards, and Equipment Installation

    A metal box contains four 12 AWG copper conductors that are spliced together and one single-pole switch mounted on a yoke. There are no cable clamps and no equipment grounding conductors in the box. What is the minimum box volume required?

    1. 9.00 cu in.
    2. 13.50 cu in.
    3. 18.00 cu in.
    4. 11.25 cu in. Correct answer.

    Explanation

    Each 12 AWG conductor that is spliced counts as 2.25 cu in., so four conductors require 9.00 cu in. A device yoke counts as one additional conductor sized to the largest conductor in the box, adding another 2.25 cu in. The total is therefore 11.25 cu in.

  142. Question 142Boxes, Raceways, Panelboards, and Equipment Installation

    What is the maximum permitted spacing between supports for a straight horizontal run of 3/4 in. electrical metallic tubing?

    1. 10 ft Correct answer.
    2. 6 ft
    3. 5 ft
    4. 3 ft

    Explanation

    Electrical metallic tubing must be supported within 3 ft of each box or termination and at intervals not exceeding 10 ft along the run. The 3 ft dimension is the distance to the first support, not the general spacing.

  143. Question 143Boxes, Raceways, Panelboards, and Equipment Installation

    Between any two pull points, what is the maximum total amount of bending permitted in a raceway run?

    1. 270 degrees
    2. 90 degrees
    3. 360 degrees Correct answer.
    4. 180 degrees

    Explanation

    The total of all bends, including offsets and kicks, must not exceed 360 degrees between outlets, junction boxes, or conduit bodies where conductors can be pulled. More bending than that makes pulling conductors impractical and damages insulation.

  144. Question 144Boxes, Raceways, Panelboards, and Equipment Installation

    What is the minimum headroom that must be provided in the working space above and in front of a 480 V panelboard?

    1. 6 ft
    2. 7 ft
    3. 6 ft 6 in. Correct answer.
    4. 8 ft

    Explanation

    The working space in front of electrical equipment must be clear to a height of 6 ft 6 in. above the floor or platform. This headroom keeps the space usable for servicing energized equipment.

  145. Question 145Boxes, Raceways, Panelboards, and Equipment Installation

    Measured from the floor, what is the maximum permitted height of the highest circuit breaker handle in a panelboard?

    1. 7 ft 0 in.
    2. 6 ft 0 in.
    3. 6 ft 7 in. Correct answer.
    4. 6 ft 6 in.

    Explanation

    Overcurrent devices must be readily accessible, and the highest handle or operating means may not be more than 6 ft 7 in. above the floor. This keeps breakers within reach of a person standing on the floor.

  146. Question 146Boxes, Raceways, Panelboards, and Equipment Installation

    A box is used to splice two 12 AWG NM cables, each containing two circuit conductors plus an equipment grounding conductor. The cables are secured by internal cable clamps, and a single receptacle is mounted on a yoke in the box. What is the minimum box volume required?

    1. 18.00 cu in.
    2. 15.75 cu in. Correct answer.
    3. 11.25 cu in.
    4. 13.50 cu in.

    Explanation

    The count is four circuit conductors plus one for the combined equipment grounding conductors, one for the cable clamps, and one for the device yoke, for seven conductor equivalents. Multiplying seven by 2.25 cu in. per 12 AWG conductor gives 15.75 cu in.

  147. Question 147Boxes, Raceways, Panelboards, and Equipment Installation

    At every outlet, switch, or junction box, what minimum length of free conductor must be provided at each conductor for splices or terminations?

    1. 6 in. Correct answer.
    2. 3 in.
    3. 4 in.
    4. 5 in.

    Explanation

    At least 6 in. of free conductor must be left at each box, measured from the point where the conductor emerges from its raceway or cable sheath. The conductor must also extend at least 3 in. beyond the opening of the box if it is not spliced or terminated there.

  148. Question 148Boxes, Raceways, Panelboards, and Equipment Installation

    The maximum number of 12 AWG THHN conductors permitted in a 1/2 in. electrical metallic tubing raceway is:

    1. 8
    2. 12
    3. 9 Correct answer.
    4. 6

    Explanation

    The interior area of 1/2 in. EMT is 0.304 sq in., and with more than two conductors the fill may not exceed 40 percent, or about 0.122 sq in. Since each 12 AWG THHN conductor has an area of 0.0133 sq in., nine conductors fit within the permitted fill.

  149. Question 149Boxes, Raceways, Panelboards, and Equipment Installation

    A PVC conduit run is installed exposed where it will be subjected to large ambient temperature swings. What does the Code require for this run?

    1. The run is limited to 50 ft between boxes
    2. The conductors must be derated for ambient temperature
    3. An expansion fitting must be installed Correct answer.
    4. The conduit must be supported every 3 ft

    Explanation

    PVC conduit expands and contracts with temperature, so expansion fittings must be installed where the expected change in length is 1/4 in. or more. They allow the conduit to move without pulling apart at joints or boxes.

  150. Question 150Boxes, Raceways, Panelboards, and Equipment Installation

    A 100-ampere branch circuit is protected by a 100-ampere circuit breaker. What is the minimum size copper equipment grounding conductor required for this circuit?

    1. 4 AWG copper
    2. 10 AWG copper
    3. 8 AWG copper Correct answer.
    4. 6 AWG copper

    Explanation

    Equipment grounding conductors are sized from the rating of the overcurrent device ahead of the equipment. For a 100-ampere device, the table requires a minimum 8 AWG copper conductor.

  151. Question 151Boxes, Raceways, Panelboards, and Equipment Installation

    What is the maximum spacing between supports for 1/2 in. through 1 in. PVC Schedule 40 conduit in a straight run?

    1. 10 ft
    2. 6 ft
    3. 3 ft Correct answer.
    4. 5 ft

    Explanation

    PVC Schedule 40 is a relatively flexible raceway, so the support table limits 1/2 in. through 1 in. sizes to 3 ft intervals. Larger sizes of the same raceway are permitted greater spacing.

  152. Question 152Boxes, Raceways, Panelboards, and Equipment Installation

    A single 2 in. raceway makes a straight pull through a box. What is the minimum length of the box measured in the direction of the pull?

    1. 12 in.
    2. 16 in. Correct answer.
    3. 20 in.
    4. 8 in.

    Explanation

    For a straight pull, the box dimension along the direction of the pull must be at least eight times the trade size of the largest raceway. Eight times 2 in. equals 16 in.

  153. Question 153Boxes, Raceways, Panelboards, and Equipment Installation

    A 480Y/277 V panelboard has exposed live parts on one side of the aisle, and the opposite side of the aisle is a grounded metal surface. What is the minimum depth of the clear working space in front of the panelboard?

    1. 5 ft
    2. 3-1/2 ft Correct answer.
    3. 3 ft
    4. 4 ft

    Explanation

    Equipment operating at 151 to 600 volts falls in the 3-1/2 ft column when live parts are exposed on one side and grounded surfaces are across the aisle from them. This is referred to as Condition 2 in the depth table.

  154. Question 154Boxes, Raceways, Panelboards, and Equipment Installation

    A 3 in. raceway enters a box and the conductors turn at an angle to exit through another raceway. What is the minimum distance from the inside of the 3 in. raceway entry to the opposite wall of the box?

    1. 24 in.
    2. 12 in.
    3. 18 in. Correct answer.
    4. 9 in.

    Explanation

    For angle or U pulls, the distance from where a raceway enters the box to the opposite wall must be at least six times the trade size of the largest raceway. Six times 3 in. equals 18 in., which leaves room for the conductors to bend without damage.

  155. Question 155Boxes, Raceways, Panelboards, and Equipment Installation

    A box contains four 10 AWG conductors and two 12 AWG conductors, all of which are spliced, plus one device mounted on a yoke. What is the minimum box volume required?

    1. 19.50 cu in.
    2. 17.00 cu in. Correct answer.
    3. 16.00 cu in.
    4. 15.00 cu in.

    Explanation

    The four 10 AWG conductors take 4 times 2.50, or 10.00 cu in., and the two 12 AWG conductors take 2 times 2.25, or 4.50 cu in. The device yoke adds one allowance equal to the largest conductor present, 2.50 cu in., for a total of 17.00 cu in.

  156. Question 156Boxes, Raceways, Panelboards, and Equipment Installation

    A 24 in. long raceway nipple is installed between two cabinets to carry several conductors. What is the maximum percentage of the nipple's interior cross-sectional area that the conductors may fill?

    1. 40 percent
    2. 31 percent
    3. 60 percent Correct answer.
    4. 53 percent

    Explanation

    Raceways used as nipples that are 24 in. or less in length are permitted a fill of up to 60 percent of the interior cross-sectional area. Because the conductors are not pulled a long distance, the higher fill is acceptable for short sections.

  157. Question 157Motors, Transformers, HVAC, and Control Circuits

    What minimum ampacity must branch-circuit conductors have for a single continuous-duty motor?

    1. 150 percent of the motor full-load current
    2. 100 percent of the motor full-load current
    3. 125 percent of the motor full-load current Correct answer.
    4. 200 percent of the motor full-load current

    Explanation

    Section 430.22 requires motor branch-circuit conductors to have an ampacity of not less than 125 percent of the motor full-load current. The full-load current is taken from the appropriate table in Article 430 based on horsepower and voltage. The extra 25 percent allows for the motor operating above its nameplate current without overheating the conductors.

  158. Question 158Motors, Transformers, HVAC, and Control Circuits

    What is the purpose of motor overload protection?

    1. It limits the available fault current at the motor.
    2. It clears short circuits in the branch circuit.
    3. It protects the motor from overload heating. Correct answer.
    4. It serves as the motor disconnecting means.

    Explanation

    Overload devices respond to a sustained current above the motor rating and are intended to prevent the motor windings from overheating. They are sized close to the motor nameplate current and are not designed to open on short circuits. Short-circuit and ground-fault protection is provided separately by the branch-circuit breaker or fuses.

  159. Question 159Motors, Transformers, HVAC, and Control Circuits

    A transformer has a 480-volt primary and a 120-volt secondary. What is its turns ratio?

    1. 2:1
    2. 1:4
    3. 4:1 Correct answer.
    4. 1:2

    Explanation

    The turns ratio equals the primary voltage divided by the secondary voltage, so 480 divided by 120 gives 4:1. Because the secondary voltage is lower, this is a step-down transformer with four primary turns for every secondary turn.

  160. Question 160Motors, Transformers, HVAC, and Control Circuits

    What control voltage is most commonly used for residential and light commercial thermostats?

    1. 120 volts
    2. 24 volts Correct answer.
    3. 12 volts
    4. 240 volts

    Explanation

    Heating and cooling control systems typically operate on a 24-volt control circuit derived from a step-down control transformer. The reduced voltage allows small, low-current thermostat contacts to switch the larger contactor and relay coils. Line voltages such as 120 or 240 volts are reserved for the actual load circuits.

  161. Question 161Motors, Transformers, HVAC, and Control Circuits

    A normally open contact on a control relay is in what state when the coil is de-energized?

    1. Open, so the circuit is incomplete Correct answer.
    2. Closed, so current flows through it
    3. Latched in its last position
    4. Open only after the coil fails

    Explanation

    The terms normally open and normally closed describe the contact state with the coil de-energized, which is the normal or resting condition. A normally open contact therefore does not conduct until the coil is energized and the contact closes.

  162. Question 162Motors, Transformers, HVAC, and Control Circuits

    In a typical HVAC condensing unit, what is the function of the contactor?

    1. It measures the refrigerant pressure in the system.
    2. It regulates the speed of the indoor blower.
    3. It switches the compressor and fan on and off. Correct answer.
    4. It converts line voltage to 24 volts for control.

    Explanation

    The contactor is a magnetically operated switch whose coil is controlled by the low-voltage thermostat circuit. When the coil is energized, the heavy-duty contacts close and apply line voltage to the compressor and condenser fan motor. This lets a small control circuit switch a much larger load current.

  163. Question 163Motors, Transformers, HVAC, and Control Circuits

    A single-phase motor has a nameplate full-load current of 16 amperes and a marked service factor of 1.15. What is the maximum rating of its overload device?

    1. 16 amperes
    2. 22 amperes
    3. 18 amperes
    4. 20 amperes Correct answer.

    Explanation

    For a motor with a marked service factor of 1.15 or greater, the overload device is set at no more than 125 percent of the nameplate full-load current. Here, 16 amperes times 1.25 equals 20 amperes. Ampere ratings of the overload device are chosen from the standard sizes permitted by the code.

  164. Question 164Motors, Transformers, HVAC, and Control Circuits

    A 75 kVA three-phase transformer is supplied at 480 volts. What is its full-load primary current?

    1. 45 amperes
    2. 78 amperes
    3. 90 amperes Correct answer.
    4. 65 amperes

    Explanation

    For a three-phase transformer, primary current equals the kVA rating times 1000 divided by the product of 1.732 and the primary voltage. That gives 75,000 divided by 831, or about 90 amperes. The square root of three factor must be included whenever the transformer is three-phase.

  165. Question 165Motors, Transformers, HVAC, and Control Circuits

    The disconnecting means for a 460-volt motor must have an ampere rating of at least what percentage of the motor full-load current?

    1. 100 percent
    2. 125 percent
    3. 115 percent Correct answer.
    4. 150 percent

    Explanation

    Section 430.110 requires the motor disconnecting means to have an ampere rating of at least 115 percent of the motor full-load current. The disconnect must also be capable of interrupting the locked-rotor current of the motor. A switch rated at exactly the running current would not provide the required margin.

  166. Question 166Motors, Transformers, HVAC, and Control Circuits

    In a three-wire start-stop control circuit, what is the purpose of the auxiliary contact wired in parallel with the start button?

    1. It limits the inrush current through the relay coil.
    2. It keeps the coil energized when the start button opens. Correct answer.
    3. It opens the circuit when the stop button is pressed.
    4. It provides overload protection for the motor circuit.

    Explanation

    The auxiliary contact, often called a seal-in or holding contact, closes when the coil energizes and maintains the circuit around the start button. This allows the operator to release the momentary start button while the coil stays energized. Pressing the stop button breaks the circuit and drops the coil out.

  167. Question 167Motors, Transformers, HVAC, and Control Circuits

    When an inverse-time circuit breaker provides short-circuit and ground-fault protection for a standard polyphase motor branch circuit, what is the maximum permitted setting?

    1. 400 percent of full-load current
    2. 175 percent of full-load current
    3. 250 percent of full-load current Correct answer.
    4. 125 percent of full-load current

    Explanation

    Table 430.52 sets the maximum inverse-time breaker setting at 250 percent of the motor full-load current for a standard motor. The higher setting is permitted because the breaker must ride through the motor's starting inrush. Overload protection is provided separately at a much lower setting.

  168. Question 168Motors, Transformers, HVAC, and Control Circuits

    How is a three-phase squirrel-cage motor reversed?

    1. Reverse the connections to the overload heaters.
    2. Interchange any two of the three line conductors. Correct answer.
    3. Reverse the neutral and ground conductors.
    4. Reverse all three line conductors.

    Explanation

    The direction of rotation of a three-phase motor is set by the phase sequence of the supply. Switching any two of the three line conductors reverses that sequence and therefore the rotation. Switching all three leaves the sequence unchanged.

  169. Question 169Motors, Transformers, HVAC, and Control Circuits

    A control transformer with a 240-volt primary and a 24-volt secondary supplies a 96 VA load. What is the secondary current?

    1. 2 amperes
    2. 4 amperes Correct answer.
    3. 3 amperes
    4. 6 amperes

    Explanation

    Secondary current equals the volt-ampere load divided by the secondary voltage, so 96 VA divided by 24 volts equals 4 amperes. The primary current would be found using the primary voltage instead. Control transformers must also be protected against overcurrent on the secondary side.

  170. Question 170Motors, Transformers, HVAC, and Control Circuits

    A Class 20 overload relay protects a motor driving a high-inertia load. From a cold start at 600 percent of rated current, the relay trips in approximately what time?

    1. 60 seconds
    2. 20 seconds Correct answer.
    3. 2 seconds
    4. 300 seconds

    Explanation

    The trip class number states the maximum trip time in seconds when the relay carries six times its rated current from a cold start. A Class 20 relay is therefore designed to trip within about 20 seconds under those conditions. Higher classes are used for loads that take longer to accelerate.

  171. Question 171Motors, Transformers, HVAC, and Control Circuits

    What is the primary function of a variable-frequency drive connected to a motor?

    1. It converts three-phase power to single-phase power.
    2. It provides short-circuit protection for the motor.
    3. It increases the motor's rated full-load current.
    4. It varies frequency and voltage to control motor speed. Correct answer.

    Explanation

    A variable-frequency drive rectifies the incoming supply and then synthesizes an adjustable output waveform. By changing both the frequency and the voltage applied to the motor, it controls the motor's speed and torque. This allows the driven load, such as a fan or pump, to match demand rather than run at a fixed speed.

  172. Question 172Motors, Transformers, HVAC, and Control Circuits

    Two motors are supplied by one feeder. Motor 1 has a full-load current of 25 amperes and motor 2 has a full-load current of 15 amperes. What is the minimum feeder ampacity?

    1. 45.0 amperes
    2. 43.8 amperes
    3. 46.3 amperes Correct answer.
    4. 40.0 amperes

    Explanation

    Section 430.24 requires the feeder ampacity to be 125 percent of the largest motor full-load current plus 100 percent of the other motor currents. That is 1.25 times 25, or 31.25 amperes, plus 15 amperes, totaling 46.25 amperes. The answer is rounded to 46.3 amperes for the minimum ampacity.

  173. Question 173Motors, Transformers, HVAC, and Control Circuits

    A 45 kVA three-phase transformer with a 480-volt primary is protected by primary-only fuses. What is the largest standard fuse size permitted?

    1. 60 amperes
    2. 70 amperes Correct answer.
    3. 90 amperes
    4. 80 amperes

    Explanation

    The primary full-load current is 45,000 divided by the product of 1.732 and 480, or about 54.1 amperes. Table 450.3(B) allows primary-only protection at up to 125 percent of that current, or about 67.6 amperes. Where that value is not a standard size, the next higher standard rating of 70 amperes may be used.

  174. Question 174Motors, Transformers, HVAC, and Control Circuits

    What is the maximum rating of a dual-element time-delay fuse used for short-circuit and ground-fault protection of a Design B polyphase motor branch circuit?

    1. 225 percent of full-load current
    2. 150 percent of full-load current
    3. 175 percent of full-load current Correct answer.
    4. 300 percent of full-load current

    Explanation

    Table 430.52 lists 175 percent of full-load current as the maximum rating for a dual-element time-delay fuse protecting a standard polyphase motor. Dual-element fuses are permitted a lower percentage than nontime-delay fuses because their time delay already tolerates starting inrush. Higher settings require justification and are limited by the table's exceptions.

  175. Question 175Motors, Transformers, HVAC, and Control Circuits

    What advantage does three-wire control have over two-wire control for a motor starter?

    1. It provides low-voltage release after a power failure. Correct answer.
    2. It needs fewer conductors to the pilot device.
    3. It lets the motor restart automatically after power loss.
    4. It removes the need for overload protection.

    Explanation

    In three-wire control, the holding contact drops out when control power is lost, so the motor does not restart on its own when power returns. This is called low-voltage release and protects personnel and equipment from unexpected restart. Two-wire control, by contrast, restores operation automatically when power returns.

  176. Question 176Motors, Transformers, HVAC, and Control Circuits

    A condensing unit nameplate lists a minimum circuit ampacity of 24.5 amperes and a maximum overcurrent protection of 40 amperes. Which installation is acceptable?

    1. 30 A conductors with a 45 A breaker
    2. 20 A conductors with a 40 A breaker
    3. 24.5 A conductors with a 40 A breaker Correct answer.
    4. 24.5 A conductors with a 50 A breaker

    Explanation

    For a listed air-conditioning unit, the branch-circuit conductors must have an ampacity of at least the nameplate minimum circuit ampacity, and the overcurrent device must not exceed the nameplate maximum. Conductors rated 24.5 amperes satisfy the minimum, and a 40-ampere breaker satisfies the maximum. The nameplate values already account for the starting current of the compressor.

  177. Question 177Special Occupancies, Special Equipment, and Hazardous Locations

    Article 518 sets the wiring requirements for buildings or portions of buildings intended for the assembly of how many persons or more?

    1. 50
    2. 200
    3. 75
    4. 100 Correct answer.

    Explanation

    Article 518 applies to buildings or portions of buildings designed or intended for the assembly of 100 or more persons, whether or not the space is used for public assembly at all hours. Below that number, the general Chapter 3 wiring methods govern.

  178. Question 178Special Occupancies, Special Equipment, and Hazardous Locations

    A location in which combustible dust is present in quantities sufficient to produce explosive or ignitible mixtures is classified as which of the following?

    1. Class II Correct answer.
    2. Class I
    3. Unclassified
    4. Class III

    Explanation

    Class II locations are those made hazardous by the presence of combustible dust. Class I covers flammable gases, vapors, and volatile liquids, and Class III covers easily ignitible fibers and flyings.

  179. Question 179Special Occupancies, Special Equipment, and Hazardous Locations

    Article 525 provides installation requirements for which of the following?

    1. Carnivals, fairs, circuses, and similar events Correct answer.
    2. Motion picture and television studios
    3. Marinas and boatyards
    4. Amusement parks and permanent theme park attractions

    Explanation

    Article 525 covers the wiring and equipment for carnivals, fairs, circuses, and similar events, which are typically temporary installations. Permanently installed amusement attractions, marinas, and studios are addressed by other articles.

  180. Question 180Special Occupancies, Special Equipment, and Hazardous Locations

    A 125-volt, 15- or 20-ampere receptacle is installed to serve permanently installed pool equipment. Which requirement applies?

    1. It must be at least 10 ft from the inside wall and need not be GFCI protected.
    2. It must be within 6 ft of the inside wall and need not be GFCI protected.
    3. It must be at least 6 ft from the inside wall and be GFCI protected. Correct answer.
    4. It must be at least 20 ft from the inside wall and be GFCI protected.

    Explanation

    Receptacles associated with permanently installed pools must be GFCI protected, and a general-purpose 15- or 20-ampere, 125-volt receptacle must be kept at least 6 ft from the inside wall of the pool. Dedicated locking-type configurations for specific equipment are handled separately in Article 680.

  181. Question 181Special Occupancies, Special Equipment, and Hazardous Locations

    The essential electrical system required for a hospital is made up of which branches?

    1. Emergency branch, standby branch, and optional branch
    2. Life safety branch and critical branch only
    3. Normal branch, emergency branch, and generator branch
    4. Life safety branch, critical branch, and equipment branch Correct answer.

    Explanation

    A Type 1 essential electrical system, as required in hospitals, is divided into the life safety branch, the critical branch, and the equipment branch, each supplying defined loads. The separation allows nonessential loads to be shed while life safety and critical loads remain energized.

  182. Question 182Special Occupancies, Special Equipment, and Hazardous Locations

    A Class I, Division 2 location is one in which which condition applies?

    1. Combustible dust is present in quantities sufficient to produce ignitible mixtures.
    2. Ignitible concentrations of gases or vapors exist under normal operating conditions.
    3. Ignitible mixtures can escape only on accidental rupture or breakdown of closed systems. Correct answer.
    4. Easily ignitible fibers are handled so that flyings are produced.

    Explanation

    Division 2 covers areas where the flammable material is confined in closed containers or closed systems and can escape only through accidental rupture or breakdown, or where handling prevents hazardous concentrations during normal operation. Hazardous concentrations present in normal operation place the area in Division 1.

  183. Question 183Special Occupancies, Special Equipment, and Hazardous Locations

    At a motor fuel dispensing facility, the emergency disconnecting means for the dispensing devices must do which of the following?

    1. Be located within 10 ft of each dispenser and be lockable only.
    2. Disconnect only the ungrounded conductors at the dispenser itself.
    3. Be accessible only to the fuel supplier.
    4. Disconnect all conductors, including the neutral, from a remote point. Correct answer.

    Explanation

    Section 514.11 requires a clearly marked, readily accessible switch located away from the dispensing devices that removes power from all dispensing equipment, including the grounded neutral conductor. This ensures the dispensers cannot remain energized during an emergency.

  184. Question 184Special Occupancies, Special Equipment, and Hazardous Locations

    In a patient care area of a hospital, how must the grounding path for receptacles be provided?

    1. Through the structural steel of the building.
    2. Through an equipment grounding conductor sized per Table 250.122 only.
    3. By an insulated copper conductor plus the metal raceway or cable armor. Correct answer.
    4. Through the metal raceway alone, provided the raceway is electrically continuous.

    Explanation

    Article 517 requires a redundant ground path in patient care areas: the metal raceway or cable armor together with an insulated copper equipment grounding conductor, with hospital-grade receptacles. The redundancy reduces the chance that a single failure leaves equipment ungrounded at the point of patient contact.

  185. Question 185Special Occupancies, Special Equipment, and Hazardous Locations

    How are intrinsically safe circuit conductors required to be installed with respect to non-intrinsically safe circuits?

    1. In the same cable tray if separated by a barrier.
    2. In separate raceways and cables from non-intrinsically safe circuits. Correct answer.
    3. In the same enclosure with no separation if the circuit operates below 50 volts.
    4. In the same raceway if the conductors are marked with orange tape at each junction box.

    Explanation

    Section 504.30 requires intrinsically safe circuit conductors to be separated from non-intrinsically safe circuits, generally by using separate raceways and cables, so that a fault or induced voltage cannot compromise the safety of the circuit. Identification and separation rules are intended to keep the energy level below ignition capability.

  186. Question 186Special Occupancies, Special Equipment, and Hazardous Locations

    In an agricultural building where livestock are confined and may contact metal equipment, Article 547 requires which of the following?

    1. Insulating mats placed under all watering and feeding equipment.
    2. A separate isolated grounding electrode not connected to the service.
    3. Only that the equipment be grounded through the metal building frame.
    4. An equipotential plane bonded to the grounding system in livestock areas. Correct answer.

    Explanation

    Article 547 requires an equipotential plane in areas where livestock are confined and can contact metal equipment, bonding the metal parts together and to the grounding electrode system. This limits the voltage differences that livestock, which are sensitive to small potential differences, can bridge.

  187. Question 187Special Occupancies, Special Equipment, and Hazardous Locations

    Electrical equipment installed within the spray area of an open spraying operation must be approved for which location?

    1. It may be general purpose if the spray gun is manually operated
    2. Class I, Division 1 Correct answer.
    3. Class I, Division 2
    4. Class II, Division 1 because of the coating dust

    Explanation

    Section 516.5 classifies the spray area of an open spraying operation as Class I, Division 1 because flammable vapors and mists from the coating are normally present during operation. Equipment within that boundary must be approved for the classified location.

  188. Question 188Special Occupancies, Special Equipment, and Hazardous Locations

    A conduit enters an explosionproof enclosure in a Class I, Division 1 location. Within what maximum distance of the enclosure must the conduit seal be located?

    1. 24 in.
    2. 18 in. Correct answer.
    3. 6 in.
    4. 12 in.

    Explanation

    In a Class I, Division 1 location, a seal must be installed in each conduit run entering an explosionproof enclosure and located within 18 in. of that enclosure. The seal prevents gases and vapors from migrating through the conduit system to equipment not rated for the location.

  189. Question 189Special Occupancies, Special Equipment, and Hazardous Locations

    A Class I, Zone 0 location is best described as one in which which condition exists?

    1. Ignitible concentrations are not likely in normal operation and occur only briefly.
    2. Ignitible concentrations are likely to exist under normal operating conditions.
    3. Ignitible concentrations are present continuously or for long periods. Correct answer.
    4. Combustible dust clouds are present continuously.

    Explanation

    Zone 0 is the most severe zone classification in the Class I zone system and covers locations where ignitible concentrations of flammable gases or vapors are present continuously or for long periods of time. Zone 1 corresponds roughly to Division 1, and Zone 2 to Division 2.

  190. Question 190Special Occupancies, Special Equipment, and Hazardous Locations

    How must the overcurrent protective device supplying a fire pump motor be selected?

    1. It must be sized to the motor nameplate full-load current, the same as for any standard motor installation.
    2. It must be omitted; fire pumps rely only on the disconnecting means.
    3. It must carry locked-rotor current indefinitely yet provide short-circuit protection. Correct answer.
    4. It must be sized to open within 10 seconds at locked-rotor current.

    Explanation

    Section 695.4 requires the overcurrent device serving a fire pump to carry indefinitely the sum of the locked-rotor currents of the fire pump motor and pressure maintenance pump motors while still providing short-circuit protection. This keeps the pump running during a fire instead of tripping on starting current.

  191. Question 191Electrical Safety, Tools, and Jobsite Practices

    Under a lockout/tagout procedure, who is authorized to remove a lock that another employee has placed on a disconnect?

    1. Only the employee who applied the lock Correct answer.
    2. Any licensed journeyman present
    3. The site superintendent on duty
    4. The senior electrician on the crew

    Explanation

    Each worker applies a personal lock and keeps the key, so the lock is removed by the person who applied it. Removal by anyone else is allowed only through the employer's documented exception procedure, which requires verifying the owner is absent and notifying them before re-energizing. Without that control, another worker could be exposed to a circuit they believed was locked out.

  192. Question 192Electrical Safety, Tools, and Jobsite Practices

    Before breaking ground for a trench on a commercial site, the crew should first:

    1. Notify the building department and obtain a trench permit
    2. Call 811 to have underground facilities located and marked Correct answer.
    3. Check the site plan for existing conduit routing
    4. Post warning signs around the excavation area

    Explanation

    Excavators must notify the one-call system, reached by dialing 811, so underground utilities can be located and marked before digging begins. The markings must be respected, and hand tools are required within the tolerance zone around marked facilities. A site plan alone does not satisfy the legal notice requirement.

  193. Question 193Electrical Safety, Tools, and Jobsite Practices

    Temporary 125-volt, single-phase, 15- and 20-ampere receptacles installed on a construction site must be:

    1. Supplied from a single dedicated branch circuit
    2. Grounded through a driven rod at each outlet
    3. Protected by ground-fault circuit-interrupter devices Correct answer.
    4. Provided with surge suppression at each outlet

    Explanation

    Construction-site receptacles rated 125 volts, 15 or 20 amperes require ground-fault circuit-interrupter protection for personnel, whether they are mounted on temporary panels or supplied by cords. The protection must be in place before the receptacle is used, not added after an incident. An assured equipment grounding conductor program is an alternative only in the limited cases the Code permits.

  194. Question 194Electrical Safety, Tools, and Jobsite Practices

    When an extension ladder is used to reach an upper level, the side rails must extend above the landing surface by at least:

    1. 12 inches
    2. 36 inches Correct answer.
    3. 18 inches
    4. 24 inches

    Explanation

    The ladder must extend at least 3 feet above the landing so a person has a handhold while stepping off and on. The base is set out about one-quarter of the working length from the wall, and the ladder is secured against movement. Too short an extension lets the ladder shift or the user step past the top.

  195. Question 195Electrical Safety, Tools, and Jobsite Practices

    An extinguisher is being staged for a temporary panelboard that will stay energized while work continues. The unit selected should carry which classification?

    1. Class A
    2. Class C Correct answer.
    3. Class D
    4. Class B

    Explanation

    Class C identifies extinguishers whose agent is non-conductive and suitable for fires involving energized electrical equipment. Once the equipment is de-energized, the fire is reclassified by what is actually burning, such as Class A combustibles. Using a water-type Class A extinguisher on live parts exposes the operator to shock.

  196. Question 196Electrical Safety, Tools, and Jobsite Practices

    A circuit has been locked out and tagged. Before the electrician begins work, the electrician must:

    1. Confirm the switch handle is in the off position
    2. Ask the equipment operator whether power was removed
    3. Check that the panel cover is securely fastened
    4. Verify the absence of voltage with a tester proven on a known source Correct answer.

    Explanation

    After lockout and tagout, a qualified person tests every phase and conductor, and proves the tester works on a known live source before and after the test. A switch position or a spoken assurance is not evidence of an electrically safe condition. The test is the step that confirms the circuit is de-energized.

  197. Question 197Electrical Safety, Tools, and Jobsite Practices

    Hand tools used on or near exposed energized parts should be:

    1. Rated and marked for the voltage, such as 1000 volts per IEC 60900 Correct answer.
    2. Limited to tools with molded composite handles
    3. At least 12 inches long overall for reach and leverage
    4. Coated with liquid plastic by the user before each shift

    Explanation

    Insulated tools must be rated and marked for the voltage involved and inspected before use for cuts, cracks, or contamination. Field-applied coatings are not a recognized insulation method because coverage and thickness cannot be controlled. Ordinary composite handles are not voltage-rated insulation.

  198. Question 198Electrical Safety, Tools, and Jobsite Practices

    What is the status of using a flexible cord or extension cord as a substitute for fixed wiring in a building?

    1. Allowed if supported overhead and protected from traffic
    2. Prohibited as a substitute for fixed wiring Correct answer.
    3. Permitted only for temporary task lighting circuits
    4. Acceptable when the cord is sized for the load

    Explanation

    Flexible cords are prohibited from being used in place of the fixed wiring of a structure, regardless of how well they are supported or sized. They also may not run through wall openings, above suspended ceilings, or under floor coverings. Cords are permitted only for the temporary and portable uses the Code recognizes.

  199. Question 199Electrical Safety, Tools, and Jobsite Practices

    An unqualified worker is positioning a fiberglass ladder near overhead lines operating at 12.5 kV. The minimum required clearance from the lines is:

    1. 6 feet
    2. 25 feet
    3. 4 feet
    4. 10 feet Correct answer.

    Explanation

    For unqualified persons, the required minimum clearance from overhead lines energized up to 50 kV is 10 feet, and this applies to equipment and the worker's body position. Greater distances apply as line voltage rises. The line owner can confirm the voltage if it is not known.

  200. Question 200Electrical Safety, Tools, and Jobsite Practices

    Work performed inside a restricted approach boundary is permitted only when:

    1. Rubber insulating gloves of Class 00 are worn
    2. The circuit is operating at less than 600 volts
    3. Two qualified journeymen are present as a team
    4. An approved energized work permit is in place Correct answer.

    Explanation

    Entering a restricted approach boundary toward exposed energized parts requires justification of the need to work energized and an approved energized electrical work permit, along with a job briefing, risk assessment, and suitable PPE. Voltage level or the number of workers present does not by itself authorize the work. Diagnostic testing is handled under a specific exception, not a general rule.

Journeyman Electrician flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Ohm's Law
The current in a circuit equals the voltage divided by the resistance, written I = E ÷ R. Rearranged, E = I × R and R = E ÷ I.
Power Formula
True power in watts equals voltage times current in a resistive circuit, P = E × I, and may also be written as I²R or E² ÷ R.
Series Circuit Current
In a series circuit the current is identical through every component, total resistance is the sum of the resistances, and the voltage divides in proportion to resistance.
Nonmetallic-Sheathed Cable Uses
Type NM cable is permitted in normally dry locations such as dwellings, but not in wet locations, in masonry voids, or where subject to physical damage.
Conduit as Grounding Means
Rigid metal conduit, IMC, and EMT are recognized equipment grounding conductors, while PVC conduit is not, so a separate equipment grounding conductor must be installed.
Box Fill for 12 AWG
Each 12 AWG conductor counts as 2.25 cubic inches of box volume, and each yoke-mounted device counts as two conductors when sizing boxes under NEC 314.16.
Grounding Electrode Conductor Sizing
The conductor connecting the grounded service point to the grounding electrode is sized from NEC Table 250.66 using the largest ungrounded service conductor.
Equipment Grounding Conductor Sizing
The equipment grounding conductor provides a low-impedance fault path and is sized from NEC Table 250.122 using the rating of the overcurrent device ahead of the equipment.
Class A GFCI Threshold
A Class A ground-fault circuit interrupter trips at 4 to 6 milliamperes of ground-fault current and provides personnel protection on 120/240 volt circuits.
Small Conductor Rule
NEC 240.4(D) limits overcurrent protection to 15 amperes for 14 AWG, 20 amperes for 12 AWG, and 30 amperes for 10 AWG copper conductors.
Interrupting Rating Requirement
An overcurrent device's interrupting rating must equal or exceed the available fault current at its line terminals, otherwise the device may fail violently during a short circuit.
Next Size Up Rule
For devices rated 800 amperes or less, the next higher standard overcurrent rating may be used when the conductor ampacity does not match a standard rating and the circuit is not multioutlet.
Continuous Load 125 Percent
A continuous load operates for 3 hours or more, and branch-circuit conductors plus overcurrent devices must be sized at not less than 125 percent of it.
Dwelling Lighting Load
Dwelling general lighting load is calculated at 3 volt-amperes per square foot, with small-appliance and laundry branch circuits added separately at 1500 VA each.
Commercial Receptacle Load
Each receptacle outlet on a commercial branch circuit is calculated at 180 volt-amperes, so ten outlets equal 1800 VA on a 20 ampere circuit.
Ampacity Correction and Adjustment
Conductor ampacity from Table 310.16 must be corrected for ambient temperature and adjusted for the number of current-carrying conductors sharing a raceway.
Bundled Conductor Derating
Four to six current-carrying conductors in one raceway require 80 percent adjustment, seven to nine require 70 percent, and ten to twenty require 50 percent.
Parallel Conductor Minimum Size
Parallel conductors must be 1/0 AWG or larger and identical in length, conductor material, size, insulation type, and termination method.
Working Space Depth
NEC 110.26 requires clear working space at least 3 feet deep, 30 inches wide, and 6.5 feet high, with depth increasing for higher voltages.
Straight Pull Box Length
A box or conduit body used for a straight pull must be at least eight times the trade size of the largest raceway entering it.
Panelboard Location Restrictions
Overcurrent devices must not be installed in bathrooms or clothes closets and must not be located over steps; they must remain readily accessible.
Motor Conductor Sizing
Motor branch-circuit conductors must have an ampacity of at least 125 percent of the motor full-load current taken from the NEC motor tables.
Motor Overload Protection
Overload protection for a motor with a marked service factor of 1.15 is typically set at 125 percent of the nameplate full-load current.
Transformer Primary Protection
For transformers with a primary current over 9 amperes, primary overcurrent protection is set at not more than 125 percent of rated primary current.
Hazardous Location Classes
Class I locations contain flammable gases or vapors, Class II locations contain combustible dust, and Class III locations contain ignitable fibers or flyings.
Division 1 Versus Division 2
Division 1 covers hazardous conditions that exist under normal operation, while Division 2 covers conditions that occur only under abnormal or fault conditions.
Pool Equipotential Bonding
Around permanently installed pools, metal parts, forming shells, and reinforcing steel must be bonded together into an equipotential grid per NEC 680.26.
Test Before Touch
Circuits must be verified de-energized with a tester rated for the voltage before work begins, and all conductors are treated as energized until tested.
Lockout Tagout Verification
Each worker applies a personal lock and tag to the energy-isolating device, then verifies isolation by attempting to start the equipment.
Limited Approach Boundary
The limited approach boundary is the distance from exposed energized parts that unqualified persons must not cross, and it increases with system voltage.
Construction Site GFCI
Temporary 125 volt, 15 and 20 ampere receptacles on construction sites require Class A ground-fault circuit interrupter protection under NEC 590.6.
Conduit Bend Limit
No more than 360 degrees of total bends is permitted between pull points in a conduit run, counting all offsets, saddles, and elbows.

Journeyman Electrician study guide

Electrical Theory, Ohm's Law, and Circuit Calculations

Core concepts

Nearly every calculation question reduces to Ohm's law (E = I × R) and the power wheel (P = E × I, P = I²R, P = E²/R), combined with the rules for series and parallel circuits. In series, current is identical everywhere and voltages add; in parallel, voltage is identical and branch currents add. Series resistances add directly; for two parallel resistors use R1R2/(R1+R2).

AC adds impedance. Inductive reactance X_L = 2πfL, capacitive reactance X_C = 1/(2πfC), and Z = √(R² + (X_L − X_C)²). Power factor is the cosine of the angle between voltage and current; watts are true power, volt-amperes are apparent power. For a balanced three-phase load, P = √3 × E_line × I_line × PF.

Traps

  • Mixing line-to-line and line-to-neutral voltages (480/277, 208/120, 240/120).
  • Substituting peak voltage where RMS is required - 120 V RMS has a peak of about 170 V.
  • Assuming the neutral carries current in a balanced three-phase, four-wire wye system; it does not.
  • Omitting power factor when converting kVA to kW.
  • Forgetting that a purely resistive load has unity power factor while a motor does not.

Worked example

A balanced 480 V, three-phase motor draws 25 A at 0.85 power factor. Apparent power = √3 × 480 × 25 ≈ 20,785 VA (20.8 kVA). True power = 20,785 × 0.85 ≈ 17,667 W (17.7 kW). Using 480 × 25 = 12 kW is single-phase math and is the classic wrong answer offered on these questions.

Wiring Methods and Materials

Core concepts

Chapter 3 of the NEC is organized one article per wiring method: 320 AC cable, 330 MC cable, 334 NM cable, 338 SE cable, 342 rigid metal conduit, 344 IMC, 348 FMC, 350 LFMC, 352 PVC, 358 EMT, 362 ENT. For each you must know three things: where it is permitted, where it is prohibited, and how it must be secured and supported.

Support and securing rules follow a pattern worth memorizing. Cable assemblies such as NM must be secured within 12 in. of a box and supported at intervals not exceeding 4.5 ft. Rigid raceways such as EMT, IMC, and RMC must be secured within 3 ft. of a box and supported at intervals not exceeding 10 ft. Fastening must be listed for the environment: standard EMT fittings cannot be used with PVC, and PVC in exposed outdoor runs needs expansion fittings to absorb thermal movement.

Traps

  • NM cable in wet or damp locations, in masonry voids, or embedded in concrete - all prohibited.
  • Assuming metal raceways are acceptable in corrosive or classified areas without examining the article for that location.
  • Ignoring conductor identification requirements (grounded conductor white/gray, equipment grounding conductor green or bare).
  • Exceeding Chapter 9 conduit fill because the pull "looked easy."
  • Using a fitting listed only for a different raceway type.

Rule of thumb

Ask yourself two questions for any method: "Is it allowed here?" and "Is it strapped right?" If either answer is uncertain, the question likely turns on that point.

Grounding, Bonding, and Ground-Fault Protection

Core concepts

Article 250 separates three ideas that questions deliberately blur. The grounded conductor (neutral) is a circuit conductor that carries current. The grounding electrode conductor (GEC) connects the grounded system to earth, sized by Table 250.66. The equipment grounding conductor (EGC) provides the low-impedance fault path back to the source, sized by Table 250.122 based on the overcurrent device rating - not the conductor ampacity.

Bonding is the intentional joining of metal parts so they stay at the same potential. The main bonding jumper connects the grounded conductor to the enclosure at the service; it is installed only at the service disconnect or at a separately derived system. Neutrals must never be bonded to enclosures downstream of that point.

A grounding electrode system must include any available metal water pipe with at least 10 ft. in earth contact, the structural steel, a concrete-encased electrode, and a ground ring. Where a water pipe is used, a supplemental electrode is required.

Traps

  • Sizing an EGC from Table 250.66 (that table is for GECs).
  • Re-bonding the neutral at a subpanel, creating parallel neutral paths.
  • Using a ground rod as the only electrode when a qualifying water pipe exists.
  • Assuming a single rod achieves 25 ohms; if it does not, a supplemental electrode is required.

Rule of thumb

The GEC to a rod or pipe electrode never needs to be larger than 6 AWG copper, and to a concrete-encased electrode never larger than 4 AWG.

Overcurrent Protection and Short-Circuit Current Ratings

Core concepts

Overcurrent protective devices must have an ampere rating that protects the conductor, an interrupting rating at least equal to the available fault current, and a short-circuit current rating adequate for the equipment it protects.

Standard device ratings (240.6) run 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000, 1200 A. The "next size up" rule in 240.4(B) allows the next higher standard device when the conductor ampacity does not match a standard rating, provided the device does not exceed 800 A, the ampacity does not correspond to a standard rating, and the circuit is not a multioutlet receptacle circuit supplying cord-and-plug loads. Small conductors have hard caps in 240.4(D): 14 AWG = 15 A, 12 AWG = 20 A, 10 AWG = 30 A.

Feeder and branch-circuit taps are permitted under 240.21. The common rules are the 10 ft. tap (ampacity not less than one-third the device rating, in raceway, no taps off the tap) and the 25 ft. tap (ampacity not less than one-third, with additional physical protection requirements).

Traps

  • Applying the next-size-up rule to a 14 AWG lighting circuit.
  • Confusing interrupting rating with SCCR of the assembly.
  • Treating a series-rated combination as a fully rated system.

Worked example

A 75°C-rated 4 AWG THWN copper conductor has an ampacity of 85 A. A 90 A standard breaker is permitted under 240.4(B) if all conditions are met - a 90 A device is the next standard size above 85 A.

Branch Circuits, Feeders, and Service Load Calculations

Core concepts

Article 210 governs branch circuits, Article 215 feeders, Article 220 calculations, and Article 230 services. The single most tested rule is the continuous-load adder: branch-circuit and feeder conductors and overcurrent devices must be sized at 125 percent of the continuous load plus 100 percent of the noncontinuous load. A continuous load is one expected to operate at maximum current for three hours or more.

For dwelling units, use the standard method in 220.42: general lighting at 3 VA per square foot, 1500 VA for each 20 A small-appliance branch circuit, 1500 VA for the laundry circuit, and nameplate ratings for fixed appliances. The general lighting and general-use receptacle load gets a demand factor - first 3000 VA at 100 percent, the remainder at 35 percent. Ranges use Table 220.55 demand factors rather than simple addition.

Non-dwelling receptacle outlets are computed at 180 VA per outlet, and 220.44 demand factors apply to the portion above 10 kVA.

Traps

  • Adding 25 percent to a load after applying demand factors instead of to the actual load.
  • Counting a receptacle outlet per device instead of per outlet (a duplex counts as one outlet).
  • Forgetting the 25 percent adder on the largest motor for service and feeder calculations.
  • Ignoring 310.12, which permits a dwelling service or feeder conductor sized at 83 percent of the service rating.

Worked example

A 2000 sq. ft. dwelling: 6000 VA lighting + 3000 VA small appliance + 1500 VA laundry = 10,500 VA. First 3000 at 100 percent = 3000; remaining 7500 at 35 percent = 2625. General load = 5625 VA before appliance and range loads are added.

Conductors, Cables, Ampacities, and Derating

Core concepts

Ampacity comes from Table 310.16, which gives values in 60°C, 75°C, and 90°C columns for copper and aluminum. The column you may use is limited by 110.14(C): the lowest temperature rating of any terminating device in the circuit caps the usable ampacity, even when the conductor itself is rated higher.

Two adjustment factors reduce ampacity. Ambient temperature correction (310.15(B)(1)) uses the ambient at the conductor, adjusted for rooftop temperature adders where applicable. Conductor count adjustment (310.15(C)(1)) applies when more than three current-carrying conductors share a raceway or cable: 80 percent for four to six, 70 percent for seven to nine. Neutral conductors count as current-carrying on wye systems with nonlinear loads such as harmonic-rich electronic ballasts.

Parallel conductors (310.10(H)) are permitted at 1/0 AWG and larger, must be the same length, material, size, and insulation, and must be terminated the same way.

Traps

  • Taking the 90°C ampacity as the final answer when terminations are 75°C rated. The correct method is to start with the 90°C value for derating, then compare the result to the 75°C value and use the lower of the two.
  • Forgetting to count a shared neutral as a current-carrying conductor.
  • Applying the conduit-fill adjustment to conductors in a nipple 24 in. or less long.

Worked example

Six current-carrying 10 AWG THHN copper conductors in a raceway at 40°C ambient. 90°C ampacity = 40 A. Ambient correction at 40°C = 0.91; six-conductor adjustment = 0.80. 40 × 0.91 × 0.80 = 29.1 A. The 75°C termination value is 35 A, so the final ampacity is 29 A.

Boxes, Raceways, Panelboards, and Equipment Installation

Core concepts

Box fill (314.16) is a volume calculation. Each conductor counts once; each cable clamp counts as one conductor of the largest size; each device or strap counts as two conductors of the largest size attached; one or more equipment grounding conductors count as a single conductor of the largest EGC. Multiply each count by the cubic-inch value in Table 314.16(B) - 2.00 for 14 AWG, 2.25 for 12 AWG, 2.50 for 10 AWG - and compare to the box volume stamped on the box.

Pull boxes are sized by 314.28. For a straight pull, the box length is eight times the trade size of the largest raceway. For an angle or U pull, distance from the raceway entry to the opposite wall is six times the largest raceway plus the sum of the other raceway sizes on the same wall.

Working clearance at equipment is set by 110.26: depth based on voltage to ground (3 ft. for 0–150 V), width of the equipment or 30 in. whichever is greater, 6.5 ft. of height, and a dedicated equipment space above and in front of the panel that must remain clear. Panelboards require overcurrent protection sized to the busbar rating (408.36).

Traps

  • Counting a duplex receptacle as two devices for box fill; it counts as two conductors total.
  • Forgetting the clamp allowance or counting each EGC separately.
  • Using the largest raceway alone for angle pulls and skipping the addition of the other raceways.
  • Ignoring the dedicated space above a panelboard where foreign piping is prohibited.

Worked example

A box contains six 12 AWG conductors, two cable clamps, two receptacles, and one EGC. Fill = 6 × 2.25 (conductors) + 2.25 (clamps) + 4 × 2.25 (two devices × two conductors each) + 2.25 (EGC) = 29.25 cu. in. A 4 × 4 × 1½ box at 21 cu. in. is too small; a 4-11/16 × 1½ box at 30.3 cu. in. works.

Motors, Transformers, HVAC, and Control Circuits

Core concepts

Motor calculations use tables, not nameplate current. Article 430 gives full-load current from Tables 430.248 (single-phase) and 430.250 (three-phase). Branch-circuit conductors are sized at 125 percent of FLC (430.22). The running overload device protects the motor from overload and is sized from the nameplate (430.32), typically 115–125 percent of nameplate current. The branch-circuit short-circuit and ground-fault protective device is sized from Table 430.52: 250 percent of FLC for an inverse-time breaker, 175 percent for a dual-element time-delay fuse, with permission to go to the next standard size.

Transformers are protected under 450.3. Primary-only protection for transformers over 1000 V differs from the 9 A rule for transformers 1000 V or less. Secondary conductors are covered by 240.21(C), which allows the 10 ft. and 25 ft. secondary tap rules when the conductors terminate in a single overcurrent device.

HVAC equipment under Article 440 uses the nameplate minimum circuit ampacity (MCA) for conductor sizing and the maximum overcurrent protective device (MOP) for the disconnect and breaker.

Traps

  • Using nameplate current instead of table FLC for motor branch conductors.
  • Using Table 430.52 instead of nameplate current for overload sizing.
  • Confusing MCA with MOP on an HVAC nameplate.

Worked example

A 5 hp, 230 V, three-phase motor has an FLC of 28 A from Table 430.250. Minimum conductor ampacity = 1.25 × 28 = 35 A. Maximum inverse-time breaker = 2.50 × 28 = 70 A.

Special Occupancies, Special Equipment, and Hazardous Locations

Core concepts

Articles 500 through 506 define classified locations. Class I is flammable gas or vapor, Class II is combustible dust, Class III is ignitable fibers. Division 1 means the hazard is present under normal conditions; Division 2 means it is present only under abnormal conditions or is contained. The zone system (Zones 0, 1, 2 for gas; 20, 21, 22 for dust) is an alternative classification. Equipment must be identified for the class, division or zone, and group, and 500-series rules control sealing, wiring methods, and boundary distances.

Other special-occupancy articles frequently tested include 511 commercial garages, 513 aircraft hangars, 514 motor fuel dispensing, 517 health care facilities, 520 places of assembly, 680 pools and fountains, and 690 solar photovoltaic systems. Special equipment includes 625 electric vehicle charging, 680 pool equipment, and 705 interconnected power production.

Separately, remember that GFCI protection (210.8) and AFCI protection (210.12) expand with each code cycle. Dwelling-unit kitchen, bathroom, garage, outdoor, and laundry receptacles all require GFCI, and most 120 V branch circuits in dwelling units require AFCI.

Traps

  • Confusing Division 1 with Division 2 - normal versus abnormal conditions.
  • Applying 210.8 to receptacles that are not in the listed locations.
  • Assuming any "explosion-proof" fitting is acceptable in a dust location.

Rule of thumb

For hazardous locations, verify three things at once: class, division or zone, and group. If any one element is missing from the equipment marking, it is not suitable.

Electrical Safety, Tools, and Jobsite Practices

Core concepts

NFPA 70E is the practical companion to the NEC. It establishes shock hazard approach boundaries - limited, restricted, and prohibited - measured from the live part, and the arc flash boundary based on incident energy. Only a qualified person may cross the restricted boundary, and only with appropriate PPE and an energized work permit. Ordinary maintenance is not a justification for working energized; de-energizing is the default.

Lockout/tagout under NEC 120.5 requires a written and audited procedure, a lock for each worker, verification that the equipment is de-energized, and a test for absence of voltage. Always test the tester on a known live source before and after testing the circuit.

Tools matter. A meter must carry a CAT rating equal to or greater than the environment - CAT III for distribution panels, CAT IV for service and utility connections. Never use a meter without a rating on service equipment.

Jobsite practices include proper ladder use (three-point contact, 4:1 angle for extension ladders), equipment inspection, and maintaining a clean, clear work area.

Traps

  • Choosing a meter by voltage rating only and ignoring the CAT rating.
  • Assuming a tag alone satisfies lockout without a personal lock.
  • Treating rubber gloves as universal PPE without a voltage class and a test date.

Rule of thumb

De-energize, lock, tag, test. If the task cannot be done de-energized, document why, perform a shock and arc flash risk assessment, and select PPE for the calculated incident energy - never by habit.

Journeyman Electrician cheat sheet

Quick reference

Electrical Theory, Ohm's Law, and Circuit Calculations

  • Ohm's law: E = I × R; rearranged, I = E ÷ R and R = E ÷ I.

  • Power: P = E × I = I²R = E² ÷ R; one horsepower equals 746 watts.

  • Series circuit: the current is common to all components, total resistance is the sum of the resistances, and voltage divides in proportion to resistance.

  • Parallel circuit: the voltage is common, 1/R_total = 1/R1 + 1/R2 + ..., and current divides inversely with resistance.

  • Two resistors in parallel: R = (R1 × R2) ÷ (R1 + R2).

  • AC sine wave: RMS (effective) value = 0.707 × peak; peak value = 1.414 × RMS.

  • Impedance Z = √(R² + X²); power factor = true power (W) ÷ apparent power (VA) = cosine of the phase angle.

  • Balanced three-phase power P = √3 × E_line × I_line × power factor; single-phase P = E × I × power factor.

  • Conductor resistance R = K × L ÷ CM, with K ≈ 12.9 for copper and 21.2 for aluminum (ohm-circular mil per foot at 75°C).

Quick reference

Wiring Methods and Materials

  • Type NM cable is limited to dry locations; it is not permitted in wet locations, embedded in masonry, in raceways outdoors, or where subject to physical damage.

  • Type MC cable is permitted in dry, damp, and wet locations and, when listed, in concrete and hazardous locations.

  • Type AC (armored) cable contains a bonding strip that must be connected to the box and to the device grounding terminal.

  • EMT, IMC, and rigid metal conduit are recognized equipment grounding conductors; PVC conduit is not, so a separate EGC must be installed.

  • Raceway fill for over two conductors is 40% of the interior cross-sectional area; one conductor 53%, two conductors 31%, and 60% for nipples 24 in or less.

  • Box fill (NEC 314.16): 14 AWG = 2.0 in³, 12 AWG = 2.25 in³, 10 AWG = 2.50 in³ per conductor; each yoke-mounted device counts as two conductors.

  • Support spacing: NM cable within 12 in of a box and every 4.5 ft; EMT within 3 ft of a box and every 10 ft; RMC and IMC every 10 ft.

  • Minimum cover (Table 300.5): 24 in for direct-buried cable, 18 in for PVC conduit, 6 in for rigid metal conduit; 12 in is permitted for GFCI-protected 120 V, 20 A residential branch circuits.

  • No more than 360 degrees of total bends is permitted between pull points in a conduit run.

Quick reference

Grounding, Bonding, and Ground-Fault Protection

  • The grounding electrode conductor is sized from Table 250.66 by the largest ungrounded service conductor and is never required to be larger than 3/0 copper or 250 kcmil aluminum.

  • A single grounding electrode must have a resistance of 25 ohms or less; if it does not, a second electrode of a permitted type must be added (250.53(A)(2)).

  • The equipment grounding conductor is sized from Table 250.122 using the rating of the overcurrent device protecting the circuit.

  • The main bonding jumper connects the grounded service conductor to the equipment grounding terminal at the service and is sized per 250.28 and Table 250.102(C)(1).

  • Metal water piping systems must be bonded within 5 ft of the point where they enter the building (250.104).

  • Class A GFCI protection trips at 4 to 6 mA and is required in dwelling bathrooms, garages, outdoors, unfinished basements, crawl spaces, kitchen countertops, and within 6 ft of sinks.

  • Ground-fault protection of equipment (GFPE) typically operates at 30 mA and is used for large services, marinas, and certain snow-melting or pipeline equipment.

  • Ground resistance is measured by the fall-of-potential method; a clamp-on ground tester is valid only on grounded-loop systems.

Quick reference

Overcurrent Protection and Short-Circuit Current Ratings

  • Standard ampere ratings include 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, and 400 A.

  • NEC 240.4(D) limits protection to 15 A for 14 AWG, 20 A for 12 AWG, and 30 A for 10 AWG copper conductors.

  • Next-size-up rule (240.4(B)): the next higher standard rating is allowed only if the device is 800 A or less, the ampacity does not match a standard size, and the circuit is not a multioutlet receptacle branch circuit.

  • The interrupting rating must equal or exceed the available fault current at the device terminals (110.9); series-rated combinations must be tested and listed as a system.

  • Class RK1, RK5, J, and CC fuses are commonly rated 200 kA interrupting; Class T fuses are current limiting with a 200 kA rating at 600 V.

  • Overcurrent devices for continuous loads are sized at not less than 125% of the continuous load plus 100% of the noncontinuous load (210.20, 215.3).

  • Devices rated 1200 A or more require arc-energy reduction means such as instantaneous trip settings or Zone Selective Interlocking (240.87).

  • Overcurrent devices must be readily accessible and must not be installed in bathrooms, clothes closets, or over steps (240.24).

  • The overcurrent device rating may not exceed the ampacity of the conductors it protects, except as specifically permitted by 240.4(B), (C), and (E) through (G).

Quick reference

Branch Circuits, Feeders, and Service Load Calculations

  • Dwelling general lighting load is 3 VA per square foot; small-appliance circuits are 1500 VA each with a minimum of two 20 A circuits, and the laundry circuit is 1500 VA.

  • Commercial receptacle outlets are calculated at 180 VA each, so ten outlets equal 1800 VA.

  • Dwelling lighting demand factors (Table 220.42): first 3000 VA at 100%, 3001 through 120,000 VA at 35%, and the remainder at 25%.

  • Electric ranges and dryers use Table 220.55 demand factors; a single 8 kW range may be calculated at 8 kW from Column C.

  • Optional dwelling method (220.82): first 10 kVA at 100%, the remainder at 40%, plus the larger of heating or cooling at 100%.

  • A continuous load operates 3 hours or more; branch-circuit conductors and overcurrent devices are sized at 125% of that load.

  • Recommended voltage drop is 3% maximum on a branch circuit, 3% on a feeder, and 5% total (210.19(A) Informational Note).

  • Dwelling receptacle spacing: no point along the wall line may be more than 6 ft from an outlet; kitchen countertops require outlets so no point is more than 24 in from one.

  • Bathroom receptacles require a dedicated 20 A branch circuit supplying only bathroom outlets.

Quick reference

Conductors, Cables, Ampacities, and Derating

  • Ampacities come from Table 310.16, but the final ampacity is limited by the lowest termination temperature rating, typically 60°C for equipment rated 100 A or less unless marked otherwise (110.14(C)).

  • Adjusted ampacity = table ampacity × ambient temperature correction factor (Table 310.15(B)(1)) × conductor bundling adjustment factor (Table 310.15(C)(1)).

  • Bundling adjustment: 4-6 conductors = 80%, 7-9 = 70%, 10-20 = 50%, 21-30 = 45%, 31-40 = 40%, and 41 or more = 35%.

  • The neutral of a multiwire branch circuit is not counted as a current-carrying conductor unless the load is nonlinear and produces triplen harmonics.

  • Parallel conductors must be 1/0 AWG or larger and identical in length, material, size, insulation, and termination.

  • Minimum branch-circuit conductor sizes: 14 AWG copper for 15 A, 12 AWG for 20 A, and 10 AWG for 30 A circuits.

  • Insulation ratings: THHN is 90°C dry and damp; THWN is 75°C wet; THWN-2 and XHHW-2 are 90°C in wet locations.

  • Conduit run on a rooftop requires the ambient temperature adder from Table 310.15(B)(3)(c) before correction factors are applied.

  • Conductor ampacity must be at least the load, and at least 125% of a continuous load unless the assembly is listed for 100% operation.

Quick reference

Boxes, Raceways, Panelboards, and Equipment Installation

  • Working space (110.26): 3 ft deep for Condition 1 (150 V or less to ground), 3.5 ft for Condition 2, and 4 ft for Condition 3; 30 in wide and 6.5 ft high.

  • Dedicated equipment space extends from the floor to 6 ft above the equipment or to the structural ceiling, whichever is lower.

  • Box volumes from Table 314.16(A): 4 × 4 × 1½ in = 21 in³, 4 × 4 × 2⅛ in = 32 in³, and 4-11/16 × 2⅛ in = 42 in³.

  • Box sizing for conduit (314.28): straight pulls require 8 times the trade size of the largest raceway; angle or U pulls require 6 times the largest plus the sum of the other raceways on the same side.

  • Panelboards must not be installed in bathrooms or clothes closets and must not be located over steps.

  • Support: EMT every 10 ft and within 3 ft of a box; RMC and IMC every 10 ft; PVC per Table 352.30.

  • A lighting and appliance branch panelboard is limited to 42 overcurrent devices unless listed otherwise.

  • Raceway penetrations of fire-rated assemblies must be sealed with a listed firestop method.

  • At the service only, the neutral is bonded to the enclosure; in subpanels the grounded and grounding conductors terminate on separate bars.

Quick reference

Motors, Transformers, HVAC, and Control Circuits

  • Motor branch-circuit conductors must have an ampacity of at least 125% of the motor full-load current taken from Tables 430.247 through 430.250, not the nameplate.

  • Motor branch-circuit protection (Table 430.52): inverse-time breaker typically 250%, dual-element fuse 175%, and non-time-delay fuse 300% of full-load current.

  • Overload protection (430.32) is set at 125% of full-load current for a motor with a 1.15 service factor or 40°C rise, and 115% otherwise.

  • The motor disconnecting means must be within sight of the controller and within 50 ft.

  • Hermetic refrigerant motor-compressor conductors are sized at 125% of rated-load current, with branch protection per 440.22.

  • Transformer protection (450.3): primary overcurrent device not more than 125% of rated primary current for transformers over 9 A; secondary not more than 125%.

  • Transformers must be accessible, ventilated, and installed with the working space required by 110.26.

  • Class 2 control circuits, such as 24 V HVAC controls, are power-limited by Article 725 and may use smaller conductors.

  • A motor controller must be rated not less than the motor horsepower and capable of starting and stopping the motor.

Quick reference

Special Occupancies, Special Equipment, and Hazardous Locations

  • Class I locations contain flammable gases or vapors, Class II locations contain combustible dust, and Class III locations contain ignitable fibers or flyings.

  • Division 1 covers conditions that exist under normal operation; Division 2 covers conditions that exist only under abnormal operation.

  • Zone classification for gases uses Zone 0 (continuous), Zone 1 (likely), and Zone 2 (unlikely); dust uses Zones 20, 21, and 22.

  • Intrinsically safe circuits must be identified, commonly with light-blue conductors, and kept separated from other wiring (Article 504).

  • Explosion-proof equipment must be listed for the class, division, and gas group, and conduit seals are required within 18 in of the enclosure.

  • Health care facilities require redundant grounding, hospital-grade receptacles, and isolated power systems in critical-care areas (Article 517).

  • Permanently installed pools require an equipotential bonding grid, and receptacles are restricted near the pool edge (680.22, 680.26).

  • Temporary wiring on construction sites requires GFCI protection for 125 V, 15 A and 20 A receptacles (590.6).

  • Marinas and boatyards require 30 mA ground-fault protection for shore-power receptacles (Article 555).

Quick reference

Electrical Safety, Tools, and Jobsite Practices

  • Circuits are treated as energized until verified de-energized with a tester rated for the voltage; the tester is checked on a known live source before and after.

  • Lockout/tagout: each worker applies a personal lock and tag, and the isolation is verified by attempting to start the equipment (OSHA 1910.147).

  • NFPA 70E establishes the limited approach boundary, restricted approach boundary, and arc-flash boundary; PPE is selected from the incident energy.

  • Unqualified persons must remain at least 10 ft from exposed energized parts operating at up to 50 kV.

  • Temporary 125 V, 15 A and 20 A receptacles on construction sites require listed GFCI protection (590.6).

  • No more than 360 degrees of bends is permitted between pull points in a conduit run.

  • Ladder setup follows the 4-to-1 rule, extends 3 ft above the landing, and is secured with three-point contact maintained.

  • Insulation resistance is measured with a megohmmeter, while voltage and continuity are measured with a multimeter of the correct CAT rating.

  • Rubber insulating gloves must be electrically retested every 6 months and air-tested before each use.

Journeyman Electrician key terms

Ohm's Law

The relationship stating that voltage equals current multiplied by resistance (E = I × R) in a purely resistive circuit; knowing any two values lets you calculate the third.

Related: Impedance, Voltage Drop
Impedance

The total opposition to alternating current from resistance plus inductive and capacitive reactance, measured in ohms; it takes the place of resistance in Ohm's Law for AC circuits.

Related: Ohm's Law, Power Factor
Power Factor

The ratio of real power in watts to apparent power in volt-amperes in an AC circuit; a value below 1.0 means some of the current does no useful work.

Related: Impedance
Voltage Drop

The voltage lost along circuit conductors because of their resistance and reactance, roughly current times conductor impedance; too much drop causes dim lights and poor equipment performance.

Related: Impedance, Ampacity
Kirchhoff's Current Law

The principle that all current entering a junction must equal all current leaving it, so the branch currents of a parallel circuit add up to the total circuit current.

Related: Parallel Circuit, Series Circuit
Series Circuit

A circuit offering only one path for current, so the same current passes through every component, the source voltage divides among them, and resistances simply add.

Related: Parallel Circuit, Kirchhoff's Current Law
Parallel Circuit

A circuit with two or more current paths connected across the same voltage, so each branch sees full voltage and the total current is the sum of branch currents.

Related: Series Circuit, Kirchhoff's Current Law
Ampacity

The maximum continuous current, in amperes, that a conductor can carry under its actual conditions of use without exceeding its rated insulation temperature.

Related: Ambient Temperature Correction, Conductor Ampacity Adjustment, Overcurrent Device
Ambient Temperature Correction

A multiplier applied to table ampacities when the surrounding air is hotter or colder than the 30°C base condition, because hot surroundings reduce a conductor's ability to shed heat.

Related: Ampacity, Conductor Ampacity Adjustment
Conductor Ampacity Adjustment

A percentage reduction of ampacity required when more than three current-carrying conductors share a raceway or cable, since bundled conductors cannot dissipate heat freely.

Related: Ampacity, Raceway Fill
Continuous Load

A load expected to draw its maximum current for three hours or longer; conductors and overcurrent devices serving it are generally sized at 125 percent of that load.

Related: Demand Factor, Branch Circuit, Overcurrent Device
Demand Factor

The ratio of the maximum demand on a system to its total connected load, applied because not every load in an installation operates at the same time.

Related: Load Calculation, Continuous Load
Load Calculation

The process of adding general lighting, receptacle, appliance, motor, and special loads and then applying demand factors to find the minimum service or feeder capacity required.

Related: Demand Factor, Feeder
Branch Circuit

The circuit conductors running from the final overcurrent device that protects the circuit to the outlets or equipment it supplies.

Related: Feeder, Overcurrent Device
Feeder

All circuit conductors between the service equipment, a separately derived source, or another supply and the final branch-circuit overcurrent devices that they energize.

Related: Branch Circuit, Load Calculation, Panelboard
Overcurrent Device

A breaker or fuse that automatically opens a circuit when current exceeds its rating for a predetermined time, protecting conductors and equipment from overheating.

Related: Interrupting Rating, Ampacity
Interrupting Rating

The highest fault current a circuit breaker or fuse can safely clear at its rated voltage, marked in amperes or thousands of amperes on the device.

Related: Short-Circuit Current Rating, Overcurrent Device
Short-Circuit Current Rating

The prospective fault current a piece of equipment can withstand without damage; it must equal or exceed the fault current available where the equipment is installed.

Related: Interrupting Rating, Series-Rated System
Series-Rated System

A tested combination in which a current-limiting device ahead of downstream breakers lets those breakers be applied where available fault current exceeds their individual interrupting ratings.

Related: Short-Circuit Current Rating, Interrupting Rating
Grounded Conductor

The circuit conductor intentionally connected to earth at the source, normally the neutral, which carries return current and is identified by white or gray insulation.

Related: Equipment Grounding Conductor, Grounding Electrode Conductor
Equipment Grounding Conductor

The conductor that ties normally non-current-carrying metal parts of equipment back to the system grounding point, creating a low-impedance path for fault current.

Related: Grounded Conductor, Bonding Jumper, Ground-Fault Circuit Interrupter (GFCI)
Grounding Electrode Conductor

The conductor linking the system grounded conductor or equipment grounding conductor to the grounding electrode, such as a ground rod, water pipe, or building steel.

Related: Grounded Conductor, Bonding Jumper
Bonding Jumper

A reliable conductor that ensures electrical continuity between metal parts required to be connected, equalizing potential and completing the path for fault current.

Related: Equipment Grounding Conductor, Grounding Electrode Conductor
Ground-Fault Circuit Interrupter (GFCI)

A device that opens the circuit when it senses a small imbalance, typically 4 to 6 milliamperes, between the hot and neutral conductors, indicating current is leaking to ground.

Related: Equipment Grounding Conductor, Ground-Fault Protection of Equipment
Ground-Fault Protection of Equipment

A system that opens the supply at a higher threshold, commonly 30 milliamperes or more, to limit damage from arcing ground faults on services and large feeders.

Related: Ground-Fault Circuit Interrupter (GFCI), Overcurrent Device
Box Fill

The internal volume a box must provide, calculated by counting conductors, devices, clamps, and grounding conductors and assigning volume allowances by conductor size.

Related: Raceway Fill, Panelboard
Raceway Fill

The limit on how much of a conduit's internal cross section conductors may occupy, set so they can be pulled without damage and heat can escape.

Related: Conductor Ampacity Adjustment, Box Fill
Working Space

The clear area that must be kept in front of electrical equipment for safe servicing, with minimum depth, width, and height determined by the voltage and conditions present.

Related: Panelboard, Lockout/Tagout
Panelboard

An assembly of busbars and overcurrent devices mounted in a cabinet that receives power from one supply and distributes it to branch circuits or feeders.

Related: Working Space, Feeder
Motor Overload Protection

A sensing device that opens the motor circuit when current or temperature stays too high for too long, preventing winding damage; it is separate from short-circuit protection.

Related: Motor Branch-Circuit Short-Circuit and Ground-Fault Protection, Service Factor
Motor Branch-Circuit Short-Circuit and Ground-Fault Protection

The fuse or instantaneous breaker selected from code tables for a motor branch circuit so it clears faults yet does not open during normal starting current.

Related: Motor Overload Protection, Overcurrent Device
Service Factor

A multiplier on a motor nameplate horsepower showing the continuous overload the motor can carry at rated conditions; it influences how overload devices are sized.

Related: Motor Overload Protection
Transformer Turns Ratio

The ratio of primary winding turns to secondary winding turns, which determines the voltage step-up or step-down and inversely sets the primary-to-secondary current relationship.

Related: Short-Circuit Current Rating
Class I, Division 1 Location

An area where ignitable gases or vapors are present during normal operations or often during maintenance, requiring the most stringent explosionproof wiring methods and equipment.

Related: Explosionproof Equipment, Intrinsically Safe Circuit
Intrinsically Safe Circuit

A circuit designed so its electrical energy, including any spark or thermal effect, is too low to ignite a hazardous atmosphere, permitting reduced wiring restrictions in classified areas.

Related: Class I, Division 1 Location, Explosionproof Equipment
Explosionproof Equipment

Enclosures built to contain an internal explosion and stop flame from escaping through machined joints, so surrounding flammable gases are not ignited.

Related: Class I, Division 1 Location, Intrinsically Safe Circuit
Arc Flash Boundary

The distance from energized equipment at which a person could receive a second-degree burn from an arc flash; only qualified workers in proper protective equipment may cross it.

Related: Personal Protective Equipment (PPE), Lockout/Tagout
Personal Protective Equipment (PPE)

Arc-rated clothing and gear such as face shields, gloves, sleeves, and insulated tools chosen to withstand the thermal and shock hazards of the work being performed.

Related: Arc Flash Boundary, Lockout/Tagout
Lockout/Tagout

The procedure of de-energizing equipment, placing a lock and tag on the disconnecting means, and verifying the absence of voltage before any work begins.

Related: Personal Protective Equipment (PPE), Working Space

Journeyman Electrician study plan

8 weeks · About 7 hours per week

Week 1

Branch Circuits, Feeders, and Service Load Calculations & Electrical Theory, Ohm's Law, and Circuit Calculations

  • Compute branch-circuit loads for general lighting, small-appliance, laundry, and receptacle outlets using the standard method

  • Calculate feeder and service loads by applying demand factors to ranges, dryers, and heating/cooling equipment

  • Solve series, parallel, and combination circuit problems for voltage, current, resistance, and power

  • Convert between watts, horsepower, and volt-amperes for single-phase and three-phase loads

  • Explain the difference between continuous and noncontinuous loads and apply the 125% factor correctly

Your checkpoint

A one-page load calculation worksheet for a 2,400 sq ft dwelling (service size, feeder size, neutral calculation) solved end to end with no reference notes

Week 2

Branch Circuits, Feeders, and Service Load Calculations & Wiring Methods and Materials

  • Size service conductors and the service disconnect for a calculated dwelling load

  • Perform optional-method load calculations and compare the result with the standard method

  • Identify and describe the wiring methods permitted in a given occupancy type

  • Match cable types and raceway types to their permitted and prohibited uses, including wet, damp, and dry locations

  • Determine support, securing, and clearance requirements for at least five common wiring methods

Your checkpoint

A comparison table of ten wiring methods listing permitted uses, prohibited uses, support spacing, and minimum size, plus two completed service calculations

Week 3

Wiring Methods and Materials & Conductors, Cables, Ampacities, and Derating

  • Apply the ampacity tables for conductors in raceways, cables, and free air at various temperature ratings

  • Calculate ampacity adjustment for more than three current-carrying conductors in a raceway

  • Apply ambient temperature correction factors to conductor ampacity

  • Determine the minimum size equipment grounding conductor and grounded conductor for a feeder

  • Select the correct box for a given conductor fill and calculate conduit fill percentage

Your checkpoint

A derating drill sheet with ten conductor scenarios (given size, insulation, ambient, and conduit count) solved with the final derated ampacity and the resulting overcurrent device size

Week 4

Grounding, Bonding, and Ground-Fault Protection

  • Identify system grounding requirements for separately derived systems and services

  • Size grounding electrode conductors and bonding jumpers for given service sizes

  • Describe the grounding electrode system and the required bonding of metal water piping and structural steel

  • Explain equipment grounding conductor sizing and the permitted uses of the raceway as an EGC

  • Distinguish ground-fault circuit interrupter, ground-fault protection of equipment, and arc-fault circuit interrupter applications and ratings

Your checkpoint

A completed grounding and bonding diagram for a single-family service (electrodes, GEC, bonding jumpers, EGCs, GFCI locations) labeled with article references

Week 5

Grounding, Bonding, and Ground-Fault Protection & Overcurrent Protection and Short-Circuit Current Ratings

  • Apply GFCI protection requirements to dwelling, kitchen, bathroom, garage, and outdoor receptacles

  • Select standard overcurrent device ratings and match them to conductor ampacities

  • Apply the next-higher-rated-device rule and identify where it is not permitted

  • Determine available short-circuit current and verify equipment short-circuit current ratings

  • Explain series-rated systems and the conditions under which they may be used

Your checkpoint

A ten-question short-circuit current rating and overcurrent protection problem set answered with the computed available fault current and a pass/fail verdict on the equipment rating

Week 6

Motors, Transformers, HVAC, and Control Circuits & Boxes, Raceways, Panelboards, and Equipment Installation

  • Size branch-circuit conductors and overcurrent protection for a single motor using the tables

  • Calculate motor overload protection and the disconnecting means rating

  • Select and size a transformer primary and secondary protection scheme for a given transformer

  • Determine working clearances, dedicated equipment space, and panelboard termination requirements

  • Calculate box fill and raceway fill for panelboard and device installations

Your checkpoint

A motor circuit worksheet covering one single-phase and one three-phase motor (conductors, branch protection, overloads, disconnect) plus a working-clearance sketch

Week 7

Special Occupancies, Special Equipment, and Hazardous Locations & Electrical Safety, Tools, and Jobsite Practices

  • Classify a location by class, division or zone, and group, then select permitted wiring methods and equipment

  • Identify requirements for commercial garages, service stations, and healthcare and assembly occupancies

  • Select the correct lockout/tagout and verification steps before working on energized equipment

  • Describe personal protective equipment selection and approach boundaries for common voltage levels

  • Explain safe use and inspection of hand and power tools and test instruments

Your checkpoint

A hazardous-location classification summary sheet (three location scenarios with class, division, group, and permitted wiring method) plus a written lockout/tagout procedure for a panelboard

Week 8

Branch Circuits, Feeders, and Service Load Calculations & Wiring Methods and Materials & Grounding, Bonding, and Ground-Fault Protection & Conductors, Cables, Ampacities, and Derating & Motors, Transformers, HVAC, and Control Circuits

  • Complete two full-length timed practice exams under test conditions and score them by domain

  • Re-solve every missed question and write the code rule or formula it tested

  • Re-drill the two lowest-scoring domains from the practice exams

  • Build a one-page formula and table-index reference sheet for exam day

  • Verify table navigation speed by locating ten cited articles and tables in under five minutes total

Your checkpoint

A scored practice exam log showing both exam results, a per-domain accuracy breakdown, and a prioritized list of the five weakest topics with the corrective action for each

Milestones

Week 2: Complete a full dwelling service and feeder calculation from scratch, including neutral and grounding conductor sizing, in under 30 minutes with no errors

Week 4: Score at least 80% on a 30-question mixed quiz covering load calculations, wiring methods, and conductor ampacity

Week 6: Score at least 80% on a 30-question quiz covering grounding and bonding, overcurrent protection, and short-circuit current ratings

Week 8: Score at least 85% overall on a full-length timed practice exam, with no domain below 70%

Journeyman Electrician exam day

Your checklist

Admission or authorization-to-test document

Bring the scheduling confirmation or authorization notice your testing provider issued, printed or saved offline on your phone. Confirm with the provider whether a printed copy is required or a digital copy is accepted.

Government-issued photo ID

Use an unexpired driver's license, state ID, passport, or military ID with your photo and signature. The name must match your registration exactly; if your registration name differs from your ID (nickname, maiden name), contact the provider before test day to fix it.

Confirmation of the code edition your exam covers

Journeyman exams are typically based on a specific edition of NFPA 70 (NEC). Verify the adopted edition for your jurisdiction and the edition your exam references; studying the wrong cycle is the most common avoidable mistake.

Required reference book, if the provider allows you to bring one

Some providers supply the code book in the exam room or provide it on-screen; others let you bring your own. Confirm with the provider whether you must bring a copy, whether it must be a specific edition, and whether a bound/unbound copy is acceptable.

Tabs, highlighting, and handwritten notes in the book

Annotation rules vary widely - some allow permanent tabs and highlighting, some prohibit loose papers and sticky notes. Confirm the provider's written policy before you mark up your book.

Approved calculator

Confirm the provider's calculator policy (permitted models, whether the test center supplies one, whether phone calculators are banned). Many providers prohibit any device with communication or programmable memory.

Leave prohibited items at home or plan for secure storage

Phones, smartwatches, fitness trackers, notes, and bags are usually barred from the testing room. Confirm whether the center offers lockers and whether phones must be powered off.

Practice navigating your code book under time pressure

Do at least two timed practice runs using the exact edition and index/table of contents you will have on test day, so tab-flipping and article lookup are automatic.

Route and arrival plan

Look up the test center address, parking, and arrival time the day before. Most centers require arrival 15–30 minutes before your appointment; confirm the specific window with the provider.

Rest and fuel

Sleep a normal night and eat a normal meal before the exam. Cramming new material in the final hours raises anxiety without improving recall.

Plan the day

Final 72 hours

Stop learning new topics. Re-read your own notes on calculations (box fill, conduit fill, ampacity, voltage drop), and do one full-length timed practice exam in the same code edition you will use. Review only the questions you missed and log why you missed them.

Final 72 hours

Confirm logistics: appointment time, test center address, acceptable ID, what you may bring into the room, and the code edition covered. Get every uncertain answer in writing from the provider.

Final 72 hours

Do one timed drill of pure index navigation - pick 20 random topics and find the governing article in under 90 seconds each.

Final 24 hours

Pack your bag: admission document, ID, approved calculator, permitted reference book, water for before the exam. Charge nothing you cannot bring in - plan to leave the phone in the car or locker.

Final 24 hours

Light review of formula sheets and your personal error list only, then stop. Set two alarms and go to bed at your normal time.

Morning of

Eat a normal meal and arrive early enough to handle parking and check-in without rushing. Leave prohibited items in the car or locker before you enter the check-in area.

Morning of

At check-in, present your ID and admission document, store personal items as directed, and read the rules sheet handed to you before you start.

During the test

Read each question twice and look for the qualifying words (except, not, minimum, first). Mark and skip anything that stalls you; come back after clearing the easy points.

During the test

For calculation items, write the given values, identify the governing article or formula, then compute - and sanity-check units and whether the answer should be larger or smaller than the inputs.

During the test

For lookups, use the index, then the article text, then tables; verify the table's footnotes and conditions before selecting an answer, since the distractor is often the unmodified table value.

During the test

Watch the clock and budget your remaining time per question. Take any breaks the provider allows per their stated policy, and review flagged items only if time remains.

Rules to check

  • Bring valid, unexpired government-issued photo ID; you will normally be refused entry without it. Confirm acceptable ID forms with the provider.

  • Personal items - phones, smartwatches, notes, bags, outerwear as specified - are generally not permitted in the testing room. Confirm storage arrangements and whether a phone must be off or surrendered.

  • The rules and any exam-day agreement are shown to you at check-in; read them before signing, because misconduct (unauthorized materials, communicating with others, photographing content) typically results in score cancellation and may be reported to the licensing board.

  • Break and unscheduled-leave policies vary by provider and can affect whether your test clock keeps running. Confirm the break policy for your exam before test day.

  • Passing scores are set by the licensing authority or provider and are usually criterion-referenced rather than curved; confirm the passing standard and score report timing with the provider rather than assuming a percentage.

  • Retake and waiting-period rules differ by jurisdiction - confirm how soon you may reschedule and how many attempts are permitted.

  • Scratch paper, pencils, and sometimes a reference copy of the code are supplied by the test center; do not assume you may bring your own, and confirm what is furnished.

  • If an equipment problem, distraction, or illness affects your performance, notify the proctor immediately and ask for it to be documented before you leave.

Journeyman Electrician FAQ

How many Journeyman Electrician practice questions are available?

The practice set has 200 Journeyman Electrician questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many Journeyman Electrician flashcards are available?

The flashcard set has 32 Journeyman Electrician cards. Each card shows the term and its definition.

Which topics does the Journeyman Electrician study material cover?

The Journeyman Electrician study material has 10 sections, including Electrical Theory, Ohm's Law, and Circuit Calculations, Wiring Methods and Materials, and Grounding, Bonding, and Ground-Fault Protection.

What format facts does the catalog list for the Journeyman Electrician exam?

The catalog lists these item types: multiple choice, calculation problems, and code-reference (open-book in many jurisdictions) for the Journeyman Electrician exam.