OSHA 510 Practice Test

OSHA 510 - Occupational Safety and Health Standards for the Construction Industry

OSHA 510 overview

  • 200 practice questions
  • 32 flashcards
  • 15 study guide topics
  • 45 key terms

What you'll study

  • OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)
  • 29 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention
  • 29 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal
  • 29 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical
  • 29 CFR 1926 Subpart L: Scaffolds
  • 29 CFR 1926 Subpart M: Fall Protection
  • 29 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations
  • 29 CFR 1926 Subpart P: Excavations
  • 29 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders
  • 29 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica
  • Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

OSHA 510 is a course title in the OSHA Training Institute Education Center catalog, commonly described as covering occupational safety and health standards for the construction industry - the 29 CFR 1926 rule set. Candidates typically include construction safety coordinators, site superintendents, competent-person designees, union trainers, and insurance or compliance staff who need working command of construction standards rather than general-industry rules. Study should be organized around the standards themselves: the Act and Subpart C general provisions; health and environmental controls, PPE, and fire protection; signs and materials handling; hand and power tools, welding, and electrical; scaffolds; fall protection; cranes and mechanized equipment; excavations; the concrete, steel, underground, demolition, blasting, power transmission, and ladder subparts; toxic and hazardous substances including hazard communication and silica; and safety program, hazard control, and recordkeeping concepts. The most reliable preparation is reading the regulatory text subpart by subpart, then testing recall with scenario questions that force you to pick the specific paragraph and numeric trigger rather than a general principle. Note that this page is independent study material and is not affiliated with or endorsed by OSHA; it does not reproduce any official course content. Verify current course logistics, scheduling, and card details directly with OSHA or an OTI Education Center, because official program pages change and some listings may be unavailable.

Common mistakes

Applying the 6-foot fall protection trigger height to every situation instead of distinguishing the general construction rule (unprotected sides and edges at 6 feet or more) from the separate triggers for scaffolds (10 feet), ladders, steel erection connectors, and controlled access zones.

Candidates memorize a single number early in study and then reuse it across Subparts L, M, and R, where different thresholds and different protective-system requirements apply; the exam deliberately tests these cross-subpart distinctions.

What to do instead

Build a one-page trigger-height table keyed by activity (general edges 6 ft, scaffolds 10 ft, steel erection 15 ft for connectors and 30 ft for controlled decking zones, excavations 6 ft for hazardous atmospheres and 5 ft for certain access requirements) and drill scenario questions until you can state which subpart governs before choosing a number.

Treating the General Duty Clause as the basis for a citation when a specific standard already covers the hazard, or citing it without being able to name the recognized hazard, the feasible means of abatement, and the employer knowledge element.

The General Duty Clause (Section 5(a)(1)) is the most quoted provision in the OSH Act, so candidates reach for it reflexively and skip the four-element test that compliance officers must establish.

What to do instead

Practice writing out all four elements for sample scenarios (hazard recognized by employer or industry, likely to cause death or serious harm, feasible and useful abatement exists, employer failed to abate) and always ask first whether a specific 29 CFR 1926 or 1910 standard applies.

Confusing the recordkeeping rules: logging first-aid-only cases on the OSHA 300, failing to record within 7 calendar days, misapplying the 24-hour reporting deadline for fatalities versus the 8-hour deadline for in-patient hospitalizations, amputations, or loss of an eye, and overlooking the 300A posting window.

The numbers 300, 300A, 301, 7 days, 8 hours, and 24 hours blur together under exam pressure, and candidates also forget that first-aid treatment and visits for diagnostic observation are not recordable.

What to do instead

Memorize a paired list: recordable on the 300 Log within 7 calendar days; report fatality within 8 hours; report in-patient hospitalization, amputation, or loss of an eye within 24 hours; post the 300A from February 1 through April 30. Then classify ten practice cases as first aid versus medical treatment.

Applying General Industry (1910) thresholds and definitions to construction scenarios, such as using the 1910 excavation, scaffold, or PPE language, or assuming a 1910 substance-specific standard governs a construction site activity.

Most study material and prior work experience are grounded in 1910, and the two sets of standards overlap in subject matter while differing in specifics; the exam is a construction-focused course and tests the 1926 text.

What to do instead

For each topic in your outline, write the 1926 citation and note one place where it differs from its 1910 counterpart (for example, 1926 Subpart P versus 1910 Subpart P, or 1926 Subpart M versus 1910 Subpart D). When a question names a construction activity, default to 1926 unless the question states otherwise.

Answering excavation questions with a single soil-type or sloping rule and ignoring the full protective-system decision sequence: competent person classification, daily inspection, protective system selection by depth and soil type, spoil pile and equipment setback, access and egress, and atmospheric testing.

Candidates latch onto the sloping charts and forget that the standard requires a protective system for any excavation 5 feet or deeper (unless the competent person determines no cave-in hazard exists), plus separate requirements for access, egress, water accumulation, and utilities.

What to do instead

Work through Subpart P as a checklist in order: competent person, soil classification, protective system (sloping, benching, shoring, or shielding), 2-foot spoil setback, 4-foot access trigger and 25-foot travel distance for ladders, and testing before entry. Apply the checklist to ten scenario questions and justify each step.

Mixing up scaffold requirements, such as applying the 4-to-1 height-to-base ratio to supported scaffolds without noting the base dimension definition, forgetting the 10-foot fall protection trigger, missing the 3-foot guardrail height and midrail placement, or overlooking the 14-inch maximum gap between the scaffold and the work face.

Subpart L contains many independent dimensional numbers, and candidates study them as a flat list rather than as a sequence of erection, access, use, and fall protection requirements.

What to do instead

Group Subpart L numbers by function: stability (4:1 ratio, base width, ties, guys), access (portable ladder, stairway, ramp, 35-degree stair angle), platform (fully planked, 14-inch maximum gap, 12-inch minimum width), and fall protection (10-foot trigger, 3-foot toprail, approximately 21-inch midrail, 200-pound load capacity). Recite the group aloud from memory before attempting questions.

Treating hazard communication and respirable crystalline silica as separate memorization exercises, missing the construction-specific obligations such as the written silica exposure control plan, the 50 micrograms per cubic meter 8-hour TWA permissible exposure limit with the 25 microgram action level, and the requirement to designate a competent person for silica.

Candidates study Subpart Z generally and skip the construction-specific table and appendix structure that the exam expects, including the distinction between the specified exposure control methods in Table 1 and the alternative exposure assessment route.

What to do instead

For silica, memorize the PEL and action level, the Table 1 task list concept, the written exposure control plan elements, medical surveillance triggers, and the competent person duty. For hazard communication, focus on the written program, container labeling, safety data sheet access, and employee training. Build a two-column comparison of what each rule requires on a construction site.

Answering electrical questions by reciting the 1910 approach-distance table or assuming that lockout and energized-work rules apply identically, without addressing construction-specific requirements such as ground-fault protection for temporary receptacles, assured equipment grounding conductor programs, and the 10-foot clearance from overhead power lines for equipment and the associated voltage-dependent distances.

Electrical content spans Subpart K and the general industry mindset, and candidates do not separate temporary wiring, GFCI requirements, and overhead line clearance distances from the 1910 qualified-person framework.

What to do instead

Write out the Subpart K essentials: GFCI or assured equipment grounding conductor program for temporary receptacles, no damaged cords, proper box covers, and overhead line clearance distances tied to voltage. Then answer five scenario questions where the correct action is de-energizing, grounding, or maintaining distance rather than wearing PPE alone.

Handling cranes and materials handling questions by recalling load-chart facts alone, ignoring the operational controls: the critical lift plan, pre-lift meeting, power line safety, swing radius barricades, outrigger blocking, and the requirement that the operator stop when a signal is given by anyone, plus the signal person qualification and hand signal knowledge.

Subparts N and CC are dense with equipment terminology, and candidates skim the operational and personnel provisions while focusing on capacity numbers that appear frequently in practice questions.

What to do instead

Build a crane scenario script: identify the load, verify the load chart and configuration, check ground conditions and outrigger blocking, confirm power line clearance and grounding, establish the barricaded swing radius, confirm signal person qualification, and confirm the operator's stop authority. Practice applying the script to lift scenarios until each element is automatic.

Treating a safety and health program as a paperwork deliverable rather than a management system, so answers describe a written policy alone instead of the proactive elements: management leadership, worker participation, hazard identification and assessment, hazard prevention and control, education and training, and program evaluation and improvement.

Program questions feel subjective, so candidates default to generic statements about commitment and training, missing the specific structural elements and the emphasis on worker participation and ongoing evaluation.

What to do instead

Memorize the program elements as a named list and, for each, write one concrete observable behavior that would demonstrate it on a site (for example, worker participation shown by workers conducting inspections and participating in incident investigations). When a scenario question appears, map the situation to the specific element that is missing rather than answering that more training is needed.

Exam requirements can change. Confirm current details with the exam provider.

OSHA 510 practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Under the OSH Act, which duty is placed directly on each covered employer by the General Duty Clause?

    1. Purchase workers' compensation insurance through a federal risk pool
    2. Furnish a workplace free from recognized hazards likely to cause death or serious physical harm Correct answer.
    3. Post the agency's inspection schedule on the company intranet
    4. Guarantee that no employee will ever be injured on the job

    Explanation

    Section 5(a)(1) requires each employer to furnish employment and a place of employment free from recognized hazards that are causing or likely to cause death or serious physical harm. It is a gap-filler used when no specific standard applies, and it does not impose strict liability for every injury.

  2. Question 2OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    A general industry employer wants to know which OSHA standards apply to its operations. Which part of Title 29 contains the general industry standards?

    1. Part 1910 Correct answer.
    2. Part 1904
    3. Part 1975
    4. Part 1926

    Explanation

    The general industry standards are codified in 29 CFR Part 1910, while construction standards sit in Part 1926. Recognizing the part number is the first step in determining which vertical standard governs a given task.

  3. Question 3OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Which citation format correctly identifies the section of 29 CFR that contains the construction industry's general safety and health provisions?

    1. 29 CFR 1926.500
    2. 29 CFR 1926.20 Correct answer.
    3. 29 CFR 1904.32
    4. 29 CFR 1910.146

    Explanation

    Subpart C of Part 1926 begins at 29 CFR 1926.20, which states the general safety and health provisions applicable to construction work. Subpart C sets duties such as accident prevention responsibilities and employee training.

  4. Question 4OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    An employer is engaged in construction work and a hazard is addressed by both a Part 1910 standard and a Part 1926 standard. Which standard generally governs?

    1. Neither standard applies until OSHA issues a citation
    2. The Part 1910 standard, because general industry standards always prevail
    3. Whichever standard the employer finds easier to comply with
    4. The Part 1926 standard, because the more specific construction standard applies Correct answer.

    Explanation

    OSHA's long-standing policy is that when a construction hazard is covered by a specific Part 1926 standard, that construction standard applies rather than the general industry counterpart. Specific standards govern over general ones addressing the same condition.

  5. Question 5OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Under 29 CFR 1926.20(b)(1), what must an employer's accident prevention responsibilities include?

    1. A written program that initiates and maintains programs to provide safe working conditions Correct answer.
    2. A monthly inspection by a federal compliance officer
    3. A bond posted with the Department of Labor before work begins
    4. A union-approved safety committee at every jobsite

    Explanation

    Section 1926.20(b)(1) requires the employer to initiate and maintain such programs as may be necessary to comply with Subpart C, including measures to ensure safe working conditions. This is the foundation for jobsite safety programs and inspections.

  6. Question 6OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    A construction employer's safety program must provide for frequent and regular inspections of jobsites, materials, and equipment. Who is permitted to perform those inspections under 29 CFR 1926.20(b)(2)?

    1. Only a licensed professional engineer
    2. Only a federal OSHA compliance officer
    3. Competent persons designated by the employer Correct answer.
    4. Any employee chosen at random each week

    Explanation

    Section 1926.20(b)(2) requires frequent and regular inspections by competent persons designated by the employer. The inspections are part of the employer's own accident prevention program, not a federal inspection activity.

  7. Question 7OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    According to 29 CFR 1926.20(b)(4), what must an employer do before permitting an employee to operate equipment or machinery?

    1. Verify that the employee holds a state-issued operator license
    2. Provide the employee a copy of the OSH Act
    3. Train the employee in the safe operation of that equipment Correct answer.
    4. Require the employee to purchase personal protective equipment

    Explanation

    Section 1926.20(b)(4) prohibits permitting an employee to operate equipment or machinery without the required training. The employer must ensure the worker is trained in safe operation before assignment.

  8. Question 8OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Under 29 CFR 1926.21, what training obligation does the employer have regarding employees exposed to conditions that could cause injury?

    1. Provide training only after the first recordable injury occurs
    2. Train only supervisors, who then informally advise their crews
    3. Provide safety and health training, including recognition and avoidance of unsafe conditions Correct answer.
    4. Delegate all training to the equipment manufacturer

    Explanation

    Section 1926.21(b) requires the employer to instruct each employee in the recognition and avoidance of unsafe conditions and in the regulations applicable to the work environment. Training must reach exposed employees, not just supervisors.

  9. Question 9OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    A worker on a construction site cannot read English and English is not the language the worker understands. What does 29 CFR 1926.21(b)(2) require of the employer's safety training?

    1. The employer must transfer the employee to a non-construction position
    2. The employer must provide training in a language and manner the employee understands Correct answer.
    3. The employer must hire a full-time interpreter for the entire crew
    4. The employer is excused from training that employee

    Explanation

    Section 1926.21(b)(2) requires the employer to instruct employees who cannot read English in the language they understand. Training delivered in a language the worker does not comprehend does not meet the standard.

  10. Question 10OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    What does 29 CFR 1926.23 require regarding first aid supplies on a construction site?

    1. A physician must be stationed at every site with more than ten workers
    2. First aid supplies must be readily accessible and a person trained to render first aid must be available Correct answer.
    3. An infirmary must be built before any site work begins
    4. First aid kits must be inspected by OSHA each quarter

    Explanation

    Section 1926.23 requires the employer to provide first aid supplies approved by the consulting physician and to have a person with first aid training available. The emphasis is on prompt access to supplies and trained assistance.

  11. Question 11OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Under 29 CFR 1926.24, what must an employer do when employees are exposed to conditions that could cause injury or illness?

    1. Provide appropriate fire protection and adequate sanitation facilities Correct answer.
    2. Wait for OSHA to specify controls in a citation
    3. Limit work to daylight hours only
    4. Rely on employees to bring their own drinking water

    Explanation

    Section 1926.24 requires the employer to provide fire protection and prevention measures and adequate sanitation facilities for employee health and safety. These are baseline site conditions the employer must furnish.

  12. Question 12OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    A construction employer assigns a worker to operate a piece of heavy equipment. Under 29 CFR 1926.20(b)(4), which action best satisfies the standard before the assignment?

    1. Assign a second worker to observe the operator from a distance
    2. Have the worker sign a waiver accepting the risk of operation
    3. Document that the worker watched a general safety orientation video two years earlier
    4. Confirm the worker has been trained in the safe operation of that specific equipment Correct answer.

    Explanation

    The paragraph bars allowing an employee to operate equipment without required training, so the employer must verify training specific to safe operation of that machinery. General orientation or a risk waiver does not substitute for equipment-specific training.

  13. Question 13OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Which statement accurately describes the relationship between the OSH Act and state plans?

    1. States may operate their own plans only if OSHA approves them as at least as effective as the federal program Correct answer.
    2. State plans are prohibited because OSHA has exclusive jurisdiction
    3. State plans may lower protections to reduce employer costs
    4. State plans apply only to federal agencies within the state

    Explanation

    Section 18 of the OSH Act allows states to assume responsibility through a plan OSHA approves as at least as effective as the federal program. Approved state plans may adopt standards that are more protective than federal requirements.

  14. Question 14OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    OSHA issues a citation to a construction employer. Under the OSH Act, what is the employer's route to contest the citation?

    1. File a notice of contest with the Secretary of Labor within 15 working days of receipt Correct answer.
    2. Appeal directly to the U.S. Supreme Court within 30 days
    3. File a grievance with the local building department
    4. Refuse to pay the penalty and wait for OSHA to sue

    Explanation

    Section 10(a) gives the employer 15 working days after receipt of the citation to notify the Secretary of Labor that it intends to contest. The contest is then heard by the Occupational Safety and Health Review Commission.

  15. Question 15OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Which element is required for OSHA to establish a violation of the General Duty Clause rather than a specific standard?

    1. The employer must have previously been cited for the same condition
    2. The hazard must be recognized and likely to cause death or serious physical harm, with a feasible means to abate it Correct answer.
    3. The condition must be addressed by an existing Part 1910 standard
    4. The employee must have suffered an injury before the citation

    Explanation

    A General Duty Clause case requires a recognized hazard causing or likely to cause death or serious physical harm, employee exposure, and a feasible and useful abatement method. It is used where no specific standard applies, so an existing standard would displace it.

  16. Question 16OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    What is the primary purpose of the construction standards in 29 CFR Part 1926 Subpart C?

    1. To set penalty amounts for willful violations
    2. To provide general safety and health requirements that apply across construction work Correct answer.
    3. To describe the process for obtaining a state plan approval
    4. To establish recordkeeping forms for injury logs

    Explanation

    Subpart C supplies general safety and health provisions that apply broadly to construction employment, such as accident prevention programs, training, first aid, and fire protection. More specific subparts address particular hazards.

  17. Question 17OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    An employer argues that because it has a written safety program, it has satisfied 29 CFR 1926.20(b). Which interpretation is most accurate?

    1. A written program alone satisfies the rule regardless of implementation
    2. The rule applies only to employers with more than 50 workers
    3. The employer must actually initiate and maintain the program, including inspections and training Correct answer.
    4. The program must be filed with OSHA before work starts

    Explanation

    Section 1926.20(b) requires the employer to initiate and maintain programs, including frequent and regular inspections by competent persons and training before equipment operation. A document that is not implemented does not meet the obligation.

  18. Question 18OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    Which of the following best describes the scope of employees covered by the OSH Act in the private sector?

    1. Only employees earning an hourly wage
    2. Only employees who are members of a labor union
    3. Only employees working in factories and manufacturing plants
    4. Employees whose employers are engaged in a business affecting interstate commerce, with limited statutory exceptions Correct answer.

    Explanation

    Section 3(5) defines employer broadly to reach businesses affecting interstate commerce, and Section 4(b) lists limited exclusions such as certain federal, state, and local government functions. Coverage is not limited by industry, union status, or pay type.

  19. Question 19OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

    A construction employer maintains a written safety program but keeps no record of the periodic jobsite inspections its competent person performs. Which requirement of 29 CFR 1926.20(b)(2) does this practice most directly undermine?

    1. The program must be submitted to OSHA for approval before any site work begins
    2. The program must guarantee that no employee is ever exposed to a hazard above a permissible exposure limit
    3. The program must require that every employee hold a current OSHA 10-hour construction card before starting work
    4. The program must provide for frequent and regular inspections of jobsites, materials, and equipment by competent persons designated by the employer Correct answer.

    Explanation

    Section 1926.20(b)(2) requires the accident prevention program to provide for frequent and regular inspections of the jobsites, materials, and equipment by competent persons designated by the employer. A written program that is never implemented through documented, competent-person inspections fails that element. OSHA does not approve individual employer programs, and the provision does not mandate OSHA 10-hour cards or guarantee zero exposure.

  20. Question 2029 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Which document is expressly required for PPE hazard assessments by general-industry 29 CFR 1910.132(d)(2), but is not generally required by construction's 29 CFR 1926 Subpart E?

    1. A daily equipment inspection log
    2. An incident report from the last injury
    3. A written hazard assessment certification Correct answer.
    4. A material safety data sheet only

    Explanation

    General-industry 29 CFR 1910.132(d)(2) requires a written certification identifying the evaluated workplace, certifier, assessment date, and document as a hazard assessment certification. Construction PPE criteria in 29 CFR 1926.95 require suitable protective equipment but do not impose that general written-certification requirement.

  21. Question 2129 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    An employer requires workers to use hard hats, safety glasses, and steel-toe boots on a demolition site. Under Subpart E, who must pay for this required PPE?

    1. The employee through payroll deduction
    2. The equipment supplier under warranty
    3. The general contractor's insurer
    4. The employer at no cost to the employee Correct answer.

    Explanation

    Subpart E provides that the employer must pay for required PPE, with limited exceptions such as non-specialty safety-toe footwear that the employee may wear off the job site and prescription safety eyewear. The default rule is employer payment for protective equipment required by the standard.

  22. Question 2229 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Before allowing an employee to use a respirator required by a Subpart D health standard, what must the employer complete?

    1. A fit test and medical evaluation per the respiratory protection program Correct answer.
    2. A written waiver signed by the employee
    3. A pulmonary function test only
    4. A toolbox talk documenting voluntary use

    Explanation

    When respirators are required, the employer must establish a written respiratory protection program that includes medical evaluation, fit testing, training, and care of the respirator. Fit testing and medical evaluation are prerequisites before required use, not optional formalities.

  23. Question 2329 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Under Subpart F, what is the minimum fire extinguisher rating required for a construction site where ordinary combustibles such as wood and paper are the primary fire hazard?

    1. Class B rating only
    2. Class C rating only
    3. Class A rating only Correct answer.
    4. Class D rating only

    Explanation

    Ordinary combustibles like wood, paper, and rubbish are Class A fire hazards, and Subpart F requires extinguishers appropriate to the anticipated fire type. Class B covers flammable liquids, Class C covers energized electrical equipment, and Class D covers combustible metals.

  24. Question 2429 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    According to Subpart D, how often must exposure monitoring be repeated when employees are exposed to noise at or above the 85 dBA action level?

    1. At least annually Correct answer.
    2. At least every six months
    3. Only after a complaint is filed
    4. At least every two years

    Explanation

    The noise standard requires monitoring whenever exposures may reach the action level, and repeat monitoring at least every two years when exposures are at or above the action level. However, when exposures exceed the permissible exposure limit, monitoring must be repeated at least annually.

  25. Question 2529 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    An employee is exposed to a noise level of 100 dBA for an 8-hour shift. What is the maximum permissible exposure duration under the construction noise standard?

    1. 2 hours Correct answer.
    2. 8 hours
    3. 4 hours
    4. 1 hour

    Explanation

    The noise table in the construction standard permits 2 hours of exposure at 100 dBA. Each 5 dBA increase halves the allowable duration, so 95 dBA allows 4 hours and 105 dBA allows 1 hour.

  26. Question 2629 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    A worker will be exposed to a substance with an 8-hour time-weighted average PEL. Which approach best determines compliance when exposure varies through the shift?

    1. Compare the highest instantaneous reading to the PEL
    2. Use only the first two hours of sampling
    3. Rely on the employee's self-report of symptoms
    4. Average the exposure over the full 8-hour shift and compare to the PEL Correct answer.

    Explanation

    Air contaminant limits in Subpart D are expressed as 8-hour time-weighted averages for full-shift exposures. Compliance is judged by integrating the varying concentrations over the sampling period rather than by a single peak reading.

  27. Question 2729 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    On a site where employees may be exposed to silica dust from cutting concrete, which control method does Subpart D require the employer to use first?

    1. Posting a warning sign at the entrance
    2. Rotating workers to limit exposure duration
    3. Engineering controls such as wet cutting or local exhaust ventilation Correct answer.
    4. Respiratory protection as the primary control

    Explanation

    Subpart D follows the hierarchy of controls, requiring feasible engineering and work practice controls before relying on respirators. Wet cutting and local exhaust ventilation are recognized engineering controls for silica-generating tasks.

  28. Question 2829 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Under Subpart E, an employee's eye protection must meet which requirement?

    1. It must be provided by the employee at personal expense
    2. It must be marked as meeting the consensus standard for eye protection Correct answer.
    3. It must be replaced monthly regardless of condition
    4. It must be tinted to reduce glare

    Explanation

    Subpart E requires protective equipment to be approved or meet the consensus standard for the specific hazard, and eye protection must bear the appropriate marking. Employers must ensure equipment is in safe condition and fits the user.

  29. Question 2929 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    A crane is operating near a power line and the employer uses a fire-resistant blanket as a safeguard. Which additional requirement applies under Subpart F?

    1. The blanket must be rated for Class D fires
    2. The operator must wear a Class C extinguisher
    3. The equipment must be grounded and the line de-energized or the blanket used with proper clearance Correct answer.
    4. The blanket must be inspected annually only

    Explanation

    Subpart F addresses fire prevention around ignition sources, and power line work requires either de-energizing and grounding or maintaining the required clearance with insulating safeguards. Fire-resistant blankets are used as insulating protection while respecting clearance distances.

  30. Question 3029 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    When must an employer provide a fire extinguisher on a construction site under Subpart F?

    1. Whenever a fire hazard exists that could be controlled by portable extinguishers Correct answer.
    2. Only during hours when a fire watch is assigned
    3. Only if the local fire department requires it
    4. Only when more than 25 employees are present

    Explanation

    Subpart F requires portable fire extinguishers, or an equivalent fire protection program, where a fire hazard exists. The employer must also ensure extinguishers are maintained, inspected, and accessible, and that employees are trained if they are expected to use them.

  31. Question 3129 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    During hot work involving welding, what must the employer ensure before the operation begins?

    1. A fire watch and removal of combustibles within the area, or other approved safeguards Correct answer.
    2. That a permit is posted for 24 hours afterward
    3. That the welder holds a Class C extinguisher
    4. That the work occurs only on weekends

    Explanation

    Hot work requires fire prevention measures such as a fire watch, clearing combustibles, or using approved guards to contain sparks and slag. These safeguards must be in place before and during the operation.

  32. Question 3229 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    An employer assigns a fire watch during hot work. What is the fire watch's primary duty?

    1. To monitor for and respond to fire conditions and sound an alarm Correct answer.
    2. To inspect the site's electrical grounding
    3. To maintain the hot work permit file
    4. To perform the welding when the welder is on break

    Explanation

    A fire watch is assigned to watch for fire, extinguish incipient fires, and notify emergency responders if needed. The fire watch must remain in place during the operation and for a period afterward to detect smoldering combustibles.

  33. Question 3329 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    A construction worker is exposed to a chemical with an 8-hour PEL of 50 ppm. Sampling shows 40 ppm for 4 hours and 20 ppm for 4 hours. How does the exposure compare to the PEL?

    1. It is below the PEL at 30 ppm TWA Correct answer.
    2. It cannot be evaluated without peak sampling
    3. It exceeds the PEL because one period is above 50 ppm
    4. It equals the PEL at 30 ppm TWA

    Explanation

    The time-weighted average is calculated as (40 ppm x 4 h + 20 ppm x 4 h) / 8 h = 30 ppm. That value is below the 50 ppm PEL, so the exposure is compliant for the full shift.

  34. Question 3429 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    An employee wears a half-mask respirator with an assigned protection factor of 10. The airborne concentration is 120 ppm and the substance has a PEL of 10 ppm. What is the maximum use concentration for this respirator?

    1. 1,200 ppm
    2. 120 ppm
    3. 100 ppm Correct answer.
    4. 10 ppm

    Explanation

    The maximum use concentration is the assigned protection factor multiplied by the exposure limit, so 10 x 10 ppm = 100 ppm. Because the measured 120 ppm exceeds that value, this respirator alone is not adequate and a higher-protection respirator is needed.

  35. Question 3529 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Which situation would require the employer to provide a hearing conservation program rather than only monitoring under the construction noise standard?

    1. Employee exposure at 80 dBA for 8 hours
    2. Employee exposure at 75 dBA for 4 hours
    3. Employee exposure at or above 85 dBA for 8 hours Correct answer.
    4. Employee exposure at 70 dBA for 8 hours

    Explanation

    The action level of 85 dBA as an 8-hour TWA triggers the hearing conservation program, including audiometric testing, hearing protection availability, and training. Exposures below the action level do not require the program.

  36. Question 3629 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    A site's fire protection plan must address which element when employees are expected to use portable extinguishers?

    1. Requiring all employees to fight incipient fires
    2. Training employees on extinguisher use and the hazards involved Correct answer.
    3. Storing extinguishers in a locked office
    4. Replacing extinguishers after each use only

    Explanation

    Subpart F requires that employees expected to use fire extinguishers be trained in their use and the hazards involved. The employer must also ensure extinguishers are inspected, maintained, and accessible.

  37. Question 3729 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    Which statement best describes the employer's duty when an employee provides their own non-specialty safety-toe footwear for a construction site?

    1. The employer must reimburse the full retail price
    2. The employer must pay for all footwear regardless of type
    3. The employer may allow employee-provided safety-toe footwear that meets the standard Correct answer.
    4. The employer must prohibit employee-provided footwear

    Explanation

    Subpart E permits employees to provide their own non-specialty safety-toe footwear as long as it meets the protective requirements. The employer remains responsible for ensuring the footwear is adequate for the hazards present.

  38. Question 3829 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention

    An employer is evaluating whether PPE fits each affected employee. Which factor is most relevant under Subpart E?

    1. The PPE was purchased in bulk for the whole crew
    2. The PPE was the least expensive compliant option
    3. The PPE is sized and selected to fit the individual user Correct answer.
    4. The color of the PPE matches company branding

    Explanation

    Subpart E requires that PPE fit each affected employee and be selected for the specific hazard. Proper fit is essential for effectiveness, particularly for respirators, hearing protection, and eye protection.

  39. Question 3929 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.200, what color must predominate in the upper panel of a danger sign?

    1. Orange
    2. Red Correct answer.
    3. Green
    4. Yellow

    Explanation

    The regulation specifies red as the predominant color in a danger sign's upper panel, with black borders and a white lower panel for additional wording. It does not assign red to every accident-prevention sign or require all lettering to be red.

  40. Question 4029 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    A construction crew must post a sign warning of a falling-load hazard. Under 29 CFR 1926.200, which basic color applies to caution signs of this type?

    1. Red
    2. Yellow Correct answer.
    3. Black
    4. Green

    Explanation

    Caution signs warn of potential hazards such as falling loads and must use yellow as the basic color, typically with black lettering and a black upper panel bearing the word CAUTION in yellow. Red is limited to danger and accident-prevention messages.

  41. Question 4129 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    According to 29 CFR 1926.201, what does a red flag used as a signaling device require of approaching traffic?

    1. Traffic must proceed with caution only when waved through
    2. Traffic must stop and wait for a green flag
    3. Traffic must come to a complete stop Correct answer.
    4. Traffic may proceed at reduced speed

    Explanation

    Section 1926.201(a) provides that signaling by flaggers and the use of flags shall conform to Part VI of the MUTCD. A red flag displayed to oncoming traffic signals that traffic must stop until the flagger directs otherwise.

  42. Question 4229 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.202, barricades used for protection of employees must meet which requirement?

    1. They must be anchored with concrete
    2. They must be at least 6 feet tall
    3. They must be painted white
    4. They must comply with the MUTCD Correct answer.

    Explanation

    Section 1926.202 requires that barricades for protection of employees conform to the applicable portions of the MUTCD. The standard does not prescribe a fixed height, color, or anchoring method beyond that conformity.

  43. Question 4329 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    A traffic-control signaling device intended to warn of a hazard must be visible to drivers. Under 29 CFR 1926.200(a), signs must be what?

    1. Approved by a licensed engineer
    2. Made of metal
    3. Legible and in English Correct answer.
    4. Removed at night

    Explanation

    Section 1926.200(a) requires that signs be legible and that the wording be in English, with additional languages permitted where needed for comprehension. This ensures workers and drivers can read the hazard message.

  44. Question 4429 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    A supervisor plans to use a danger sign where an immediate hazard exists. Under 29 CFR 1926.200(c), how must danger signs be distinguished from caution signs?

    1. Danger signs use yellow with black letters
    2. Danger signs use orange with black letters
    3. Danger signs use green with white letters
    4. Danger signs use red as the basic color with contrasting letters Correct answer.

    Explanation

    Section 1926.200(c) specifies that danger signs use red as the basic color with contrasting letters such as white. Caution signs, by contrast, use yellow with black lettering. The color distinction signals the relative severity of the hazard.

  45. Question 4529 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(a)(1), how must all materials stored in tiers be secured?

    1. By stacking, blocking, interlocking, or limiting height Correct answer.
    2. By covering with tarps
    3. By placing on wooden pallets only
    4. By tying with rope only

    Explanation

    Section 1926.250(a)(1) requires stored materials to be stacked, blocked, interlocked, and limited in height so they are stable and secure against sliding or collapse. Any combination achieving stability is acceptable.

  46. Question 4629 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    A stack of lumber is stored outdoors on a construction site. Under 29 CFR 1926.250(a)(2), what must be provided for drainage?

    1. A concrete pad
    2. A sump pump
    3. A raised steel rack
    4. Adequate drainage Correct answer.

    Explanation

    Section 1926.250(a)(2) requires storage areas to be kept free from accumulation of materials that could cause tripping, fire, or explosion, and to have adequate drainage. Water accumulation undermines stability and creates slip hazards.

  47. Question 4729 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(b)(1), how high may a stack of bagged materials be built when they are to be manually handled?

    1. No more than 10 feet
    2. No more than 20 feet
    3. No more than 4 feet
    4. To a height that ensures stability Correct answer.

    Explanation

    Section 1926.250(b)(1) requires bagged materials to be stacked by stepping back the layers and cross-keying the bags at least every 10 bags high, and stacks must be stable. The standard governs stability rather than a single fixed height.

  48. Question 4829 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(b)(2), what must be done to a stack of bricks that is more than 4 feet high?

    1. Tapered back one-quarter of the width at the base Correct answer.
    2. Covered with plastic sheeting
    3. Restacked daily
    4. Tied with wire

    Explanation

    Section 1926.250(b)(2) requires brick stacks over 4 feet high to be tapered back one-quarter of the width of the stack at the base. This tapering improves stability and reduces the risk of toppling.

  49. Question 4929 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(b)(5), how must cylindrical materials stored in racks be secured?

    1. By wedges or chocks at the bottom tier Correct answer.
    2. By placing them in bins
    3. By tying each cylinder to the rack
    4. By stacking them horizontally

    Explanation

    Section 1926.250(b)(5) requires cylindrical materials stored in racks to be prevented from spreading by providing wedges or chocks at the bottom tier. This keeps the cylinders from rolling out of the rack.

  50. Question 5029 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(b)(8), how must materials stored in a silo or bin be handled to prevent collapse?

    1. By emptying it weekly
    2. By inspecting and maintaining the structure Correct answer.
    3. By keeping the silo sealed
    4. By loading from the top only

    Explanation

    Section 1926.250(b)(8) requires silos and bins to be inspected and maintained to prevent collapse. Structural integrity of the container is the key safeguard for workers nearby.

  51. Question 5129 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    A worker needs to remove material from a storage pile. Under 29 CFR 1926.250(c), what must be done to prevent an avalanche of material?

    1. Remove from the top and keep the pile sloped Correct answer.
    2. Wet the material down
    3. Use a front-end loader only
    4. Remove from the bottom first

    Explanation

    Section 1926.250(c) requires removal of material from storage piles in a manner that prevents danger of sliding or collapse, generally by working from the top down with a controlled slope. Undercutting the pile creates an overhang that can collapse.

  52. Question 5229 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(d)(1), what is required for aisles and passageways in storage areas?

    1. They must be paved with concrete
    2. They must be kept clear and in good repair Correct answer.
    3. They must be at least 8 feet wide
    4. They must be marked with red tape

    Explanation

    Section 1926.250(d)(1) requires aisles and passageways to be kept clear and in good repair, with no obstruction across or in them that could create a hazard. This preserves egress and movement of equipment.

  53. Question 5329 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.252(a), how must materials be handled when they are being removed from a building?

    1. Pushed through windows
    2. Dropped into a dumpster
    3. Thrown from the roof
    4. Lowered by a chute or hoist Correct answer.

    Explanation

    Section 1926.252(a) requires that whenever materials are dropped more than 20 feet to any point outside the exterior walls, an enclosed chute of wood or equivalent material be used. Other removal methods must avoid creating hazards to workers below.

  54. Question 5429 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.252(b), when must a substantial gate or equivalent protection be provided at a debris chute opening?

    1. When the chute is made of metal
    2. When the chute is used at night
    3. When the chute discharges into an enclosed container Correct answer.
    4. When the chute is over 10 feet long

    Explanation

    Section 1926.252(b) requires that when debris is dropped through holes in the floor without the use of a chute, the area onto which the material is dropped be completely enclosed with barricades at least 42 inches high and that a substantial gate be provided when the chute discharges into an enclosed container.

  55. Question 5529 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(a)(3), what must be done with materials that could create a fire hazard in a storage area?

    1. Labeled with a red tag
    2. Stored outdoors only
    3. Covered with a fire blanket
    4. Removed or stored safely Correct answer.

    Explanation

    Section 1926.250(a)(3) addresses keeping storage areas free of accumulations that could cause tripping, fire, or explosion, requiring combustible scrap and debris to be removed or stored safely. Good housekeeping is the controlling principle.

  56. Question 5629 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

    Under 29 CFR 1926.250(b)(3), what must be done with lumber stored on the ground to protect it from deterioration and instability?

    1. It must be covered with gravel
    2. It must be stored indoors
    3. It must be treated with chemicals
    4. It must be stacked on a raised foundation Correct answer.

    Explanation

    Section 1926.250(b)(3) requires lumber to be stacked on a solid, level foundation or on a raised foundation to prevent contact with the ground and to keep the stack stable. Ground contact promotes rot and uneven settling.

  57. Question 5729 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Under 29 CFR 1926.300, what must the employer do for all hand and power tools and similar equipment furnished by the employer?

    1. Require employees to purchase their own tools
    2. Replace them whenever a new model is released
    3. Inspect them only after an injury occurs
    4. Ensure they are maintained in a safe condition Correct answer.

    Explanation

    Section 1926.300(a) requires that all hand and power tools and similar equipment, whether furnished by the employer or the employee, be maintained in a safe condition. This is a baseline duty that applies before any specific tool rule. It is not conditioned on model updates or on injuries occurring.

  58. Question 5829 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    A grinder is used in a shop where workers are exposed to flying chips. According to 1926.300(b)(1), what guarding is required at the point of operation?

    1. A guard that is adjusted so the operator's hands are not exposed to the hazard Correct answer.
    2. A guard only when the tool is operated above shoulder height
    3. A guard that is removed for precision work at the operator's discretion
    4. A warning sign posted at the shop entrance

    Explanation

    When power tools are used in a location where the operator or others are exposed to flying chips, 1926.300(b)(1) requires a guard at the point of operation that is adjustable and that prevents the operator's hands from entering the hazardous area. A sign does not substitute for guarding. Guards are not discretionary for precision work.

  59. Question 5929 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Which practice satisfies 1926.300(b)(2) when an employee uses a portable circular saw?

    1. Holding the work with one hand while cutting with the other
    2. Securing the work with a clamp and keeping the lower guard functional Correct answer.
    3. Reaching across the blade to support the cutoff piece
    4. Setting the blade depth to the full thickness of the stock

    Explanation

    Section 1926.300(b)(2) requires that work be supported and secured against movement while the tool is in use. Clamping the work and retaining the functioning lower guard meets that duty. Hand-holding the stock or reaching across the blade defeats the securing requirement.

  60. Question 6029 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Under 1926.301(a), what is the required condition of the wooden handles on hand tools such as hammers and axes?

    1. Kept tight and free of splinters and cracks Correct answer.
    2. Coated with a smooth oil finish to prevent swelling
    3. Replaced with metal handles whenever available
    4. Shortened periodically to remove worn grain

    Explanation

    Section 1926.301(a) requires that wooden handles be kept tight and free of splinters and cracks. A loose, splintered, or cracked handle can fail or let the head fly off. Oil finishes, handle material substitution, and shortening are not the standard's requirement.

  61. Question 6129 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    An employee must cut a metal stud with a powder-actuated tool. Which practice complies with 1926.302(c)?

    1. Loading the tool in the gang box before climbing the ladder
    2. Leaving the tool loaded between fastening tasks for speed
    3. Carrying the loaded tool with the muzzle pointed down
    4. Loading the tool at the point of use and never carrying it loaded Correct answer.

    Explanation

    Section 1926.302(c) requires powder-actuated tools to be loaded just before use and not carried loaded. Loading at the point of use limits the chance of an unintended discharge. Carrying or storing the tool loaded violates that precaution.

  62. Question 6229 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    What does 1926.302(b)(1) require for the exposed moving parts of power tools such as belts, gears, and shafts?

    1. They must be painted a warning color
    2. They must be guarded to prevent employee contact Correct answer.
    3. They must be enclosed only when the tool is unattended
    4. They must be lubricated at the start of each shift

    Explanation

    Section 1926.302(b)(1) requires that exposed moving parts of power tools be guarded so that employees cannot contact them. Guards must be in place during operation, not only when the tool is idle. Paint and lubrication are maintenance measures, not guarding.

  63. Question 6329 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    An abrasive wheel on a bench grinder is being mounted. Under 1926.303, which element is required to be provided and properly adjusted?

    1. A foot pedal for starting the grinder
    2. A chip deflector on the floor below the machine
    3. A work rest and tongue guard with the gaps kept within the specified limits Correct answer.
    4. A lockout hasp on the grinder's disconnect

    Explanation

    Section 1926.303 requires abrasive wheel grinders to have work rests and adjustable tongue guards, with the work rest gap and the tongue guard clearance kept within the distances the standard specifies. These controls limit the gap where a workpiece or body part could be drawn into the wheel. Floor deflectors and start pedals are not the requirement.

  64. Question 6429 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Before an abrasive wheel is mounted on a grinder, what must be done with the wheel according to 1926.303?

    1. It must be soaked in coolant for one hour
    2. It must be marked with the operator's name
    3. It must be inspected and ring-tested, and damaged wheels must not be used Correct answer.
    4. It must be run at full speed without a guard for break-in

    Explanation

    Section 1926.303 requires that abrasive wheels be inspected and ring-tested before mounting, and that cracked or damaged wheels be rejected. A defective wheel can burst at operating speed. Soaking, unguarded break-in, and name marking are not required.

  65. Question 6529 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Under 1926.304, what is required of circular saw blades that are used on construction sites?

    1. They must be stored with the guard removed
    2. They must be painted with a high-visibility color
    3. They must be replaced at the end of each shift
    4. They must be kept sharp and free of missing teeth Correct answer.

    Explanation

    Section 1926.304 addresses woodworking tools and requires that saw blades be kept sharp and free of missing teeth. A dull blade or missing teeth increase kickback and breakage risk. Color coding, shift-based replacement, and removing guards are not requirements.

  66. Question 6629 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    A cutting operation with an oxygen-fuel gas torch is planned near combustible material. Which control does 1926.352 require?

    1. Removing or protecting combustibles, or using guards to confine heat, sparks, and slag Correct answer.
    2. Posting a fire watch only after the fire starts
    3. Wetting the combustibles once at the start of the shift
    4. Relying on the building sprinkler system alone

    Explanation

    Section 1926.352 requires that when welding or cutting is done, combustible material be moved away or protected, and that suitable guards confine the heat, sparks, and slag. These controls address ignition before it occurs. A fire watch is a supplemental control, not a substitute for removing or protecting combustibles.

  67. Question 6729 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    During gas welding, which shutdown practice is appropriate when a welder leaves the immediate work area, such as at a break?

    1. The fuel gas valve may remain open if the oxygen is closed
    2. The torch valves must be closed and the equipment shut down Correct answer.
    3. The torch may be left burning with the hoses coiled
    4. The torch may be hung on the workpiece

    Explanation

    Close the torch valves and shut down the gas-welding equipment before leaving it unattended for a break. This avoids leaving a burning torch or uncontrolled gas flow in the work area. Closing only one valve or moving the torch does not provide an appropriate shutdown.

  68. Question 6829 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    What does 1926.351(a) require regarding the cylinder valve protection caps on oxygen and fuel gas cylinders?

    1. Caps must be welded to the cylinder collar
    2. Caps must be in place whenever the cylinder is not in use or connected for service Correct answer.
    3. Caps must be replaced with plastic plugs
    4. Caps must be removed at all times to allow leak detection

    Explanation

    Section 1926.351(a) requires that valve protection caps be kept on cylinders whenever the cylinders are not in use or connected for service. The caps protect the valve from damage that could cause a violent release. Removing caps for routine leak checks or substituting plugs defeats that protection.

  69. Question 6929 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    Under 1926.351(c), how must oxygen and fuel gas cylinders in storage be separated?

    1. They may be stored together when the building is sprinklered
    2. They may be stored side by side if both are chained
    3. Oxygen cylinders must be separated from fuel gas cylinders by a specified distance or a noncombustible barrier Correct answer.
    4. They may be stored together if the caps are removed

    Explanation

    Section 1926.351(c) requires oxygen cylinders in storage to be separated from fuel gas cylinders by a specified distance or by a noncombustible barrier of specified height. The separation reduces the chance that a fuel gas fire reaches oxygen and intensifies. Chaining alone does not satisfy the separation requirement.

  70. Question 7029 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    An extension cord on a construction site has a damaged outer jacket exposing the conductors. Under 1926.404, what is the correct action?

    1. Wrap the damaged area with electrical tape and continue use
    2. Remove the cord from service and repair or replace it Correct answer.
    3. Mark the cord and continue use until the end of the project
    4. Use the cord only for low-voltage tools

    Explanation

    Section 1926.404 addresses wiring design and protection, and flexible cords with damaged insulation or jackets are not permitted to be used. A cord with exposed conductors must be removed from service and repaired or replaced. Taping over damage or restricting use does not make the cord acceptable.

  71. Question 7129 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    What does 1926.404(b)(1) require for receptacles used by employees on a construction site?

    1. Ground-fault circuit interrupter protection for all 125-volt, single-phase, 15- and 20-ampere receptacles Correct answer.
    2. A separate grounding electrode at each receptacle
    3. Isolation transformers for every receptacle
    4. Double insulation on all tools plugged into the receptacle

    Explanation

    Section 1926.404(b)(1) requires ground-fault circuit interrupter protection for all 125-volt, single-phase, 15- and 20-ampere receptacle outlets on construction sites that are not part of the permanent wiring of the building. GFCI protection guards against ground faults that could cause electrocution. Isolation transformers and per-receptacle electrodes are not the required control.

  72. Question 7229 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    A crew is working near an energized overhead line. Under 1926.400 and related requirements, what must be determined and maintained before work begins?

    1. The number of workers on the crew
    2. The color of the line's insulators
    3. The age of the utility pole
    4. The voltage of the line and the minimum approach distance, with the line de-energized or guarded if needed Correct answer.

    Explanation

    Electrical safety requirements in Subpart K require that the voltage of exposed lines be determined and that minimum approach distances be maintained, with lines de-energized or otherwise protected where the distance cannot be kept. Insulator color, pole age, and crew size do not establish electrical safety. Maintaining distance is the primary control against contact.

  73. Question 7329 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    A portable electric tool shows a defective strain-relief fitting where the cord enters the housing. What does 1926.404 require?

    1. The tool may be used if the cord is taped to the housing
    2. The tool may be used if the circuit has a GFCI
    3. The tool must be removed from service until the fitting is repaired Correct answer.
    4. The tool may be used if the worker wears insulating gloves

    Explanation

    Section 1926.404 requires that cords and their fittings be maintained in good condition; a defective strain relief exposes the conductors to pull and abrasion. The tool must be taken out of service until repaired. Taping, gloves, or a GFCI on the circuit does not correct the defect.

  74. Question 7429 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical

    A welding crew is setting up oxy-fuel gas welding equipment. Under 29 CFR 1926.350, which practice is required when connecting regulators and torches to oxygen and fuel gas cylinders?

    1. Connect the oxygen hose to the fuel gas regulator first so the system can be purged before the fuel gas is attached
    2. Tape over the regulator inlet threads so that either hose can be attached to either cylinder
    3. Use fittings and connections that are designed to prevent the interchange of oxygen and fuel gas hose and regulator connections Correct answer.
    4. Allow any standard threaded fitting to be used as long as the connection is tightened with a wrench

    Explanation

    1926.350 requires that oxygen and fuel gas fittings be of the type that cannot be interchanged, so fuel gas cannot be connected to oxygen service or vice versa. This prevents mixing of gases and the explosion hazard that results from contaminating oxygen equipment with oil or fuel gas.

  75. Question 7529 CFR 1926 Subpart L: Scaffolds

    Under 29 CFR 1926 Subpart L, at what minimum height above a lower level must an employee be protected from falling when working on a scaffold?

    1. 15 feet
    2. 6 feet
    3. 4 feet
    4. 10 feet Correct answer.

    Explanation

    Subpart L requires fall protection for employees working on a scaffold more than 10 feet above a lower level. The 10-foot trigger applies to scaffold work and differs from the 6-foot trigger used for many other construction activities.

  76. Question 7629 CFR 1926 Subpart L: Scaffolds

    When scaffold platforms are more than 10 feet above a lower level, what must be provided along all open sides and ends of the platform?

    1. Toe boards without any top rail
    2. A warning line system only
    3. A safety monitoring system only
    4. Guardrail systems or equivalent fall protection Correct answer.

    Explanation

    Subpart L requires guardrail systems or other appropriate fall protection along all open sides and ends of platforms more than 10 feet above a lower level. Warning lines and safety monitoring systems are not substitutes for guardrails on scaffolds.

  77. Question 7729 CFR 1926 Subpart L: Scaffolds

    What is the minimum design load that scaffold platforms and the supporting structure must be capable of supporting, per Subpart L?

    1. Exactly the maximum intended load
    2. At least ten times the maximum intended load
    3. At least four times the maximum intended load Correct answer.
    4. At least twice the maximum intended load

    Explanation

    Scaffolds and scaffold components must be capable of supporting, without failure, their own weight and at least four times the maximum intended load applied or transmitted to them. This 4:1 safety factor is a core design requirement.

  78. Question 7829 CFR 1926 Subpart L: Scaffolds

    What is the minimum nominal lumber size for scaffold planking used as a platform?

    1. 2 x 10 inch Correct answer.
    2. 1 x 6 inch
    3. 2 x 4 inch
    4. 1 x 10 inch

    Explanation

    Subpart L specifies that scaffold platforms may be constructed of lumber of nominal 2 x 10 inch or wider sizes, or other equivalent material. Thinner or narrower lumber does not meet the platform plank requirement.

  79. Question 7929 CFR 1926 Subpart L: Scaffolds

    Scaffold platforms and walkways must generally be at least how wide?

    1. 24 inches
    2. 36 inches
    3. 18 inches Correct answer.
    4. 12 inches

    Explanation

    Subpart L requires scaffold platforms and walkways to be at least 18 inches wide, with limited exceptions for certain specialized scaffolds. A narrower platform does not provide adequate footing for workers.

  80. Question 8029 CFR 1926 Subpart L: Scaffolds

    On a supported scaffold, what is the general maximum allowable gap between a platform and an upright, or between adjacent platforms, where a person could fall through?

    1. Gaps must not exceed 9.5 inches
    2. Gaps must not exceed 1 inch Correct answer.
    3. No gap is ever permitted
    4. Gaps must not exceed 18 inches

    Explanation

    Subpart L generally limits gaps between platform units and between a platform and an upright to 1 inch. A wider gap requires the employer to demonstrate its necessity. The platform must then be decked as fully as possible, with remaining space between the platform and uprights no greater than 9.5 inches.

  81. Question 8129 CFR 1926 Subpart L: Scaffolds

    What is the maximum spacing of rest platforms along a stairway-type ladder used for scaffold access when the ladder climb exceeds 30 feet?

    1. Every 30 feet
    2. Every 50 feet
    3. Every 12 feet
    4. Every 20 feet Correct answer.

    Explanation

    Subpart L requires rest platforms at intervals not exceeding 20 feet along stairway-type ladders used for scaffold access where the total climb exceeds 30 feet. The rest platforms reduce fatigue and fall risk during long climbs.

  82. Question 8229 CFR 1926 Subpart L: Scaffolds

    Which of the following is an acceptable means of access to a scaffold platform under Subpart L?

    1. Using a portable ladder positioned against the scaffold
    2. Climbing the scaffold's cross bracing
    3. Using a stairway-type ladder or a portable ladder placed so it will not tip Correct answer.
    4. Climbing the end frames of the scaffold

    Explanation

    Subpart L permits access by stairway-type ladders, ramps, walkways, and portable ladders positioned so they will not tip, among other listed means. Climbing cross bracing and end frames is prohibited.

  83. Question 8329 CFR 1926 Subpart L: Scaffolds

    On a newly manufactured supported scaffold, what is the minimum height of the top edge of a guardrail above the scaffold platform?

    1. 36 inches
    2. 38 inches Correct answer.
    3. 30 inches
    4. 48 inches

    Explanation

    For a newly manufactured supported scaffold, the top edge of the guardrail must be at least 38 inches above the platform. The ordinary specified range is 38 to 45 inches. Older supported scaffolds and specified suspended scaffolds may use a 36-inch minimum.

  84. Question 8429 CFR 1926 Subpart L: Scaffolds

    When is a midrail required on a scaffold guardrail system?

    1. When there is no equivalent protection between the top rail and the platform Correct answer.
    2. Only when the top rail is below 42 inches
    3. Never, since the top rail alone is sufficient
    4. Only on suspended scaffolds

    Explanation

    A midrail must be installed when there is no equivalent protection between the top rail and the platform surface. This prevents a worker from falling through the space beneath the top rail.

  85. Question 8529 CFR 1926 Subpart L: Scaffolds

    A scaffold is being erected near an energized power line. What is the minimum clearance distance for insulated power lines under Subpart L?

    1. 20 feet
    2. 3 feet
    3. 10 feet Correct answer.
    4. 5 feet

    Explanation

    Subpart L requires that scaffolds not be erected, moved, dismantled, or altered so that any conductive element comes closer than 10 feet to any insulated power line, unless de-energized or protected. Greater distances apply to uninsulated lines.

  86. Question 8629 CFR 1926 Subpart L: Scaffolds

    Before a scaffold is used, who must inspect it and at what frequency?

    1. Only at the time of initial erection
    2. Only after a fall occurs
    3. By a competent person, before each work shift and after any occurrence that could affect its integrity Correct answer.
    4. Once per week by any employee

    Explanation

    A competent person must inspect the scaffold and its components before each work shift and after any occurrence that could affect structural integrity, such as a storm or impact. The inspection ensures the scaffold remains safe for use.

  87. Question 8729 CFR 1926 Subpart L: Scaffolds

    What is the required footing for a supported scaffold's base plates or screw jacks?

    1. They may rest directly on soft soil
    2. They must be supported by the building's roof only
    3. They must be embedded at least 4 feet in the ground
    4. They must be set on a firm foundation and level, with base plates or screw jacks where required Correct answer.

    Explanation

    Supported scaffolds must have a firm, level foundation, and base plates or screw jacks must be used to distribute the load and allow leveling. Soft or uneven ground can cause settlement and collapse.

  88. Question 8829 CFR 1926 Subpart L: Scaffolds

    How must a supported scaffold be secured to prevent tipping?

    1. It may stand free without any ties if it is short
    2. It must be anchored only at the top
    3. It must be welded to the ground
    4. It must be braced and tied to the structure or otherwise stabilized as needed for stability Correct answer.

    Explanation

    Subpart L requires supported scaffolds to be braced and tied to the structure or otherwise stabilized so they cannot tip or collapse. Free-standing scaffolds must be stable under the intended loads and conditions.

  89. Question 8929 CFR 1926 Subpart L: Scaffolds

    On a suspension scaffold, what is the minimum number of independent support lines required for a two-point adjustable suspension scaffold?

    1. Four
    2. One
    3. Three
    4. Two, each independent of the scaffold's primary support Correct answer.

    Explanation

    Two-point adjustable suspension scaffolds require two independent support lines, each capable of supporting the scaffold, in addition to the primary suspension ropes. These back-up lines protect against failure of the primary support.

  90. Question 9029 CFR 1926 Subpart L: Scaffolds

    What is the maximum allowable deflection of a scaffold platform under the maximum intended load?

    1. 1/30 of the span
    2. 1/200 of the span
    3. 1/60 of the span Correct answer.
    4. 1/100 of the span

    Explanation

    Subpart L limits platform deflection to no more than 1/60 of the span when loaded. Excessive deflection can make the platform unstable and difficult to walk on.

  91. Question 9129 CFR 1926 Subpart L: Scaffolds

    Which employees are permitted to work on or from a scaffold during erecting, dismantling, or moving operations?

    1. Any employee who volunteers
    2. Only employees who are trained and authorized, under the supervision of a competent person Correct answer.
    3. Any employee wearing a hard hat
    4. Only employees with more than five years of experience

    Explanation

    Subpart L restricts work on scaffolds during erection, dismantling, or moving to trained, authorized employees under the supervision of a competent person. Untrained workers are exposed to collapse and fall hazards.

  92. Question 9229 CFR 1926 Subpart L: Scaffolds

    What is the minimum height of toe boards on a scaffold platform where falling objects may endanger employees below?

    1. 6 inches
    2. 10 inches
    3. 4 inches Correct answer.
    4. 2 inches

    Explanation

    Subpart L requires toe boards at least 4 inches high on platforms where falling objects could endanger employees below. Toe boards keep tools and materials from being kicked off the platform edge.

  93. Question 9329 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.501(b)(1), when an employee is exposed to an unprotected side or edge of a walking/working surface with an unprotected edge 6 feet or more above a lower level, the employer must do which of the following?

    1. Provide a warning line at least 6 feet from the edge
    2. Post a sign warning of the fall hazard and continue work
    3. Select and install a guardrail, safety net, personal fall arrest, or other approved fall protection system Correct answer.
    4. Require employees to wear high-visibility vests near the edge

    Explanation

    Section 1926.501(b)(1) requires conventional fall protection-guardrail systems, safety net systems, or personal fall arrest systems-or an approved alternative whenever a walking/working surface has an unprotected side or edge 6 feet or more above a lower level. Signs, warning lines alone, or vests do not satisfy the duty to provide fall protection.

  94. Question 9429 CFR 1926 Subpart M: Fall Protection

    For purposes of 29 CFR 1926 Subpart M, the term 'lower level' refers to a surface or area below the walking/working surface that is:

    1. A surface that has been designated as a controlled access zone
    2. Only ground level or the lowest floor of the structure
    3. Any surface more than 12 inches below the work area
    4. A surface or area to which an employee could fall, regardless of the height differential Correct answer.

    Explanation

    Section 1926.500(a) and the definition section describe a lower level as a surface or area to which an employee can fall, which is why the 6-foot trigger is measured between the working surface and whatever lies below it. The trigger is not tied to a fixed 12-inch threshold or limited to ground level.

  95. Question 9529 CFR 1926 Subpart M: Fall Protection

    Which of the following best describes the 6-foot fall protection trigger height under 29 CFR 1926.501(b)(1)?

    1. It requires fall protection only when the surface is 10 feet or more above a lower level
    2. It requires fall protection when the walking/working surface is 6 feet or more above a lower level Correct answer.
    3. It applies only when a worker is within 3 feet of an edge
    4. It applies only to steel erection activities

    Explanation

    The general rule in 1926.501(b)(1) triggers fall protection at 6 feet above a lower level for construction work. Steel erection has its own standard in Subpart R, and the Subpart M trigger is not 10 feet.

  96. Question 9629 CFR 1926 Subpart M: Fall Protection

    An employee is performing roofing work on a low-slope roof. Under 29 CFR 1926.501(b)(10), when is conventional fall protection required for roofing work on roofs with a slope less than or equal to 4:12?

    1. Never, because roofing work is exempt from Subpart M
    2. Only when the roof height exceeds 16 feet
    3. When the roof height is 6 feet or more above a lower level, unless the employer uses the specified warning line and safety monitor combination Correct answer.
    4. Only when the roof area exceeds 1,000 square feet

    Explanation

    For low-slope roofs, 1926.501(b)(10) permits a warning line system erected not less than 6 feet from the roof edge combined with a safety monitoring system, but only when the work meets the conditions in that paragraph. Otherwise conventional fall protection is required at 6 feet or more.

  97. Question 9729 CFR 1926 Subpart M: Fall Protection

    An employer is using a warning line system for roofing work on a low-slope roof. Under 29 CFR 1926.502(f)(2), what is the minimum height of the warning line above the walking/working surface?

    1. 34 inches
    2. 39 inches Correct answer.
    3. 30 inches
    4. 42 inches

    Explanation

    Section 1926.502(f)(2) specifies that warning lines must be erected not less than 6 feet from the roof edge and must be between 34 and 39 inches above the walking/working surface. The upper bound of that range is 39 inches.

  98. Question 9829 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.502(d)(15), personal fall arrest systems must be rigged so that an employee can neither free fall more than 6 feet nor contact any lower level. Which requirement applies to the total fall distance calculation?

    1. The system must be rigged to limit free fall to 6 feet and prevent contact with a lower level, accounting for deceleration distance and worker height Correct answer.
    2. Only the lanyard length is considered
    3. The anchorage point may be at the employee's feet as long as the lanyard is short
    4. Deceleration distance may be ignored when a shock-absorbing lanyard is used

    Explanation

    Section 1926.502(d)(15) limits free fall to 6 feet and requires that the system be rigged to prevent contact with any lower level, which requires accounting for lanyard length, deceleration distance, and the worker's body length. A shock absorber does not eliminate the need to compute total fall distance.

  99. Question 9929 CFR 1926 Subpart M: Fall Protection

    What is the minimum required tensile strength for a personal fall arrest system anchorage used to attach personal fall arrest equipment under 29 CFR 1926.502(d)(15)?

    1. 3,000 pounds
    2. 1,000 pounds
    3. 5,000 pounds Correct answer.
    4. 2,000 pounds

    Explanation

    Section 1926.502(d)(15) requires anchorages used for attachment of personal fall arrest equipment to be independent of any anchorage being used to support or suspend platforms and capable of supporting at least 5,000 pounds per employee attached. This is a design strength requirement, not a working load.

  100. Question 10029 CFR 1926 Subpart M: Fall Protection

    An employee is working from a personal fall arrest system with a 6-foot shock-absorbing lanyard attached at shoulder level. Which statement correctly reflects the rigging requirements of 29 CFR 1926.502(d)(16)?

    1. Free fall distance need not be limited if the anchorage is overhead
    2. The lanyard may be attached to a guardrail that is not designed as an anchorage
    3. The system may be attached to any structure capable of holding the employee's weight
    4. The system must limit maximum arresting force to 1,800 pounds when used with a body harness Correct answer.

    Explanation

    Section 1926.502(d)(16) requires personal fall arrest systems to limit the maximum arresting force on an employee to 1,800 pounds when used with a body harness. Attachment points must be designed anchorages, not incidental structures such as guardrails.

  101. Question 10129 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.502(c), safety net systems must be installed as close as practicable under the walking/working surface, but in no case more than how far below that surface?

    1. 15 feet
    2. 10 feet Correct answer.
    3. 30 feet
    4. 20 feet

    Explanation

    Section 1926.502(c)(1) requires safety nets to be installed as close as practicable under the walking/working surface on which employees are working and never more than 10 feet below that surface. Nets must also extend outward from the edge of the work surface as specified.

  102. Question 10229 CFR 1926 Subpart M: Fall Protection

    An employer is establishing a controlled access zone for a leading edge work operation. Under 29 CFR 1926.502(g)(2), which of the following is an acceptable method for controlling access to the zone?

    1. A guardrail system installed only on the side facing the public
    2. A rope, wire, or other similar barrier with a limited number of access points Correct answer.
    3. A sign reading 'Authorized Personnel Only' with no physical barrier
    4. A single warning line with no other control

    Explanation

    Section 1926.502(g)(2) allows control of access to a controlled access zone by a rope, wire, or other similar barrier that has a limited number of access points, along with other specified combinations such as a control line and signs. A sign alone or a single warning line does not control access.

  103. Question 10329 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.502(b)(1), what is the required minimum top-rail height for a guardrail system used as fall protection?

    1. 45 inches
    2. 42 inches Correct answer.
    3. 39 inches
    4. 36 inches

    Explanation

    Section 1926.502(b)(1) requires the top edge height of top rails or equivalent guardrail system members to be 42 inches plus or minus 3 inches above the walking/working level. The 39-inch figure is the lower bound of the tolerance, not the nominal height.

  104. Question 10429 CFR 1926 Subpart M: Fall Protection

    A guardrail system is being used along an open-sided floor. Under 29 CFR 1926.502(b), which requirement applies to the midrail?

    1. A midrail must be installed at 30 inches above the walking/working level
    2. A midrail is required only on stairways
    3. A midrail must be installed at approximately 21 inches above the walking/working level Correct answer.
    4. A midrail is optional if the top rail is present

    Explanation

    Section 1926.502(b) requires midrails, screens, mesh, intermediate vertical members, or equivalent intermediate members installed between the top edge and the walking/working surface, with midrails at a height midway between the top edge and the walking/working level, approximately 21 inches.

  105. Question 10529 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.502(b)(3), what minimum load must a guardrail system withstand when forces are applied in a downward or outward direction at any point along the top edge?

    1. 200 pounds Correct answer.
    2. 50 pounds
    3. 150 pounds
    4. 100 pounds

    Explanation

    Section 1926.502(b)(3) requires guardrail systems to withstand a force of at least 200 pounds applied within 2 inches of the top edge in a downward or outward direction. This load requirement ensures the rail resists a worker leaning or falling against it.

  106. Question 10629 CFR 1926 Subpart M: Fall Protection

    An employee is using a positioning device system for work on a vertical surface. Under 29 CFR 1926.502(e), which requirement applies to the rigging of the system?

    1. The system must be rigged to prevent the employee from falling a distance greater than 2 feet
    2. The system may allow a free fall of up to 6 feet if a shock absorber is used
    3. The system must be rigged to allow free fall of no more than 2 feet Correct answer.
    4. The system requires no secondary fall arrest backup under any circumstance

    Explanation

    Section 1926.502(e)(1) requires positioning device systems to be rigged so that an employee cannot free fall more than 2 feet. Positioning systems are not primary fall arrest and must be backed up where required by the applicable work standard.

  107. Question 10729 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.502(d)(21), personal fall arrest systems must be inspected by the employer for defects:

    1. Before each use and at intervals as required by the manufacturer Correct answer.
    2. Annually by a competent person
    3. Only after a fall event has occurred
    4. Monthly by a qualified engineer

    Explanation

    Section 1926.502(d)(21) requires personal fall arrest systems to be inspected prior to each use for wear, damage, and other deterioration, and defective components to be removed from service. Manufacturer instructions may impose additional inspection intervals.

  108. Question 10829 CFR 1926 Subpart M: Fall Protection

    An employer is using a safety monitoring system as part of a fall protection plan for low-slope roofing work. Under 29 CFR 1926.502(h)(1), which requirement applies to the safety monitor?

    1. The monitor must be a competent person who is responsible for recognizing and warning employees of fall hazards Correct answer.
    2. The monitor must be positioned at the roof edge to physically restrain employees
    3. The monitor may monitor an area larger than that which can be seen without visual aids
    4. The monitor may perform other duties while monitoring

    Explanation

    Section 1926.502(h)(1) requires the safety monitor to be a competent person whose only responsibility is to recognize and warn employees of fall hazards. The monitor must be able to see the monitored employees and must not have other duties that interfere with monitoring.

  109. Question 10929 CFR 1926 Subpart M: Fall Protection

    An employer is developing a fall protection plan under 29 CFR 1926.502(k) for a work operation where conventional fall protection is infeasible or creates a greater hazard. Which element must the plan include?

    1. A statement that the plan will be implemented under the supervision of a competent person and a description of the training provided to employees Correct answer.
    2. A schedule for annual replacement of all lanyards regardless of condition
    3. A list of all employees who have previously fallen on the site
    4. A copy of the manufacturer's catalog for all fall protection equipment

    Explanation

    Section 1926.502(k) requires a fall protection plan prepared by a qualified person and, among other elements, implemented under the supervision of a competent person, with a description of the training provided and the reasons conventional fall protection is infeasible or creates a greater hazard.

  110. Question 11029 CFR 1926 Subpart M: Fall Protection

    Under 29 CFR 1926.503(a), which employees must receive fall protection training?

    1. Employees who might be exposed to fall hazards, including the recognition of hazards and the procedures to follow Correct answer.
    2. Only supervisory personnel
    3. Only employees who work above 10 feet
    4. Only employees who have previously been involved in a fall

    Explanation

    Section 1926.503(a)(1) requires the employer to provide a training program for each employee who might be exposed to fall hazards, covering the nature of fall hazards, the correct procedures for erecting and using fall protection systems, and the use and operation of the systems. The trigger is potential exposure, not prior incidents or job title.

  111. Question 11129 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1417, when must the procedures applicable to the operation of a crane be complied with?

    1. At all times during operation, including assembly and dismantling Correct answer.
    2. Only when the manufacturer's manual is physically on site
    3. Only during the initial inspection after delivery to the site
    4. Only when the load exceeds 75 percent of the rated capacity

    Explanation

    Section 1926.1417 requires that the equipment be operated in accordance with applicable manufacturer procedures and the employer's operating procedures at all times, including during assembly, disassembly, and travel. Compliance is not conditioned on load size or on whether the manual happens to be present in the cab.

  112. Question 11229 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane is being assembled on a construction site. Under 29 CFR 1926.1404, who must be in charge of the assembly operation?

    1. The general contractor's site superintendent by default
    2. Any rigger holding a valid rigger qualification
    3. An employee designated as the competent person for assembly Correct answer.
    4. The crane operator alone, without additional direction

    Explanation

    Section 1926.1404 requires that assembly and disassembly be directed by a person who meets the criteria for a competent person and who is designated to be in charge of the operation. That individual must understand the hazards and the manufacturer's assembly procedures.

  113. Question 11329 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    What is the required minimum clearance between energized power lines and any part of a crane, load line, or load, for lines rated over 350 kV?

    1. 15 feet
    2. 20 feet Correct answer.
    3. 10 feet
    4. 50 feet

    Explanation

    Table T of 29 CFR 1926.1408 sets minimum approach distances by voltage; for lines over 350 kV the minimum clearance is 20 feet. Lower voltages carry smaller distances, such as 10 feet for lines up to 50 kV.

  114. Question 11429 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1412, a crane that has been in service for more than one year must receive which type of inspection?

    1. A monthly inspection only
    2. No recurring inspection if it passed initial inspection
    3. A pre-shift inspection only
    4. An annual comprehensive inspection Correct answer.

    Explanation

    Section 1926.1412 requires a comprehensive annual inspection of equipment that has been in service for more than one year, covering items such as structural members, brakes, and safety devices. Monthly and shift-level inspections are separate, more frequent requirements.

  115. Question 11529 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1419, what is the primary purpose of the signal person during crane operations?

    1. To record the weight of each load lifted
    2. To inspect the crane's wire rope before each shift
    3. To authorize changes to the lift plan
    4. To direct the operator when the point of operation is not in full view Correct answer.

    Explanation

    Section 1926.1419 requires a signal person when the point of operation is not in full view of the operator, when the operator's view is obstructed, or when the operator or the person handling the load determines it is necessary. The signal person relays directions to the operator.

  116. Question 11629 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane will be working near a 120 kV overhead power line and the employer chooses to use a dedicated spotter. Which requirement applies to the spotter under 29 CFR 1926.1408?

    1. The spotter must hold a crane operator certification
    2. The spotter may perform rigging duties while spotting
    3. The spotter is required only if the line exceeds 350 kV
    4. The spotter must be positioned to see the operator and the power line and be able to warn the operator Correct answer.

    Explanation

    Section 1926.1408 requires a dedicated spotter who is positioned to maintain a clear view of the equipment, the power line, and the operator, and who can effectively warn the operator. The spotter's role must not be combined with other duties that would impair that function.

  117. Question 11729 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1423, which fall protection is required for an employee who must access the crane's boom walkway to perform maintenance?

    1. Only a warning line system
    2. No fall protection if the employee is trained
    3. Fall protection meeting the requirements of 29 CFR 1926 Subpart M Correct answer.
    4. Only a safety monitoring system

    Explanation

    Section 1926.1423 requires that employees exposed to fall hazards on cranes be protected by fall protection systems meeting the criteria of Subpart M. Training alone does not eliminate the need for a fall arrest or other compliant system.

  118. Question 11829 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane is lifting a load over a walkway where employees must pass. Under 29 CFR 1926.1425, what is required before employees are permitted to pass beneath the load?

    1. A hoist that is fully controlled by the operator and a determination that the load will not pass over employees Correct answer.
    2. A separate signal person stationed at each end of the walkway
    3. A minimum of two riggers present at all times
    4. A warning sign posted at the walkway entrance

    Explanation

    Section 1926.1425 generally prohibits hoisting over employees, and where the employer believes it is necessary, the operator must have full control of the hoist and the employer must ensure the load will not pass over employees. The standard emphasizes preventing exposure rather than providing warning.

  119. Question 11929 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane's load line will be used to lift a personnel platform. Under 29 CFR 1926.1431, which condition must be satisfied before personnel may be hoisted?

    1. The crane must have been inspected within the previous 30 days
    2. The total weight of the platform and personnel must not exceed 50 percent of the crane's rated capacity for that configuration Correct answer.
    3. The platform must be certified by the manufacturer of the crane
    4. The lift must be performed only during daylight hours

    Explanation

    Section 1926.1431 limits the combined weight of the platform, its rigging, and the personnel to no more than 50 percent of the crane's rated capacity for the configuration being used. This margin provides reserve capacity and stability when personnel are exposed.

  120. Question 12029 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1427, which of the following is a valid way for an operator to be qualified to operate a crane?

    1. Being designated by the site superintendent
    2. Being certified by a recognized certification entity or qualified by the employer after evaluation Correct answer.
    3. Having five years of experience with any type of equipment
    4. Possessing a valid driver's license

    Explanation

    Section 1926.1427 requires operators to be certified or qualified through an evaluation of their ability to operate the equipment safely, which may be certification by a recognized entity or employer qualification following a practical and knowledge assessment. Experience alone or a designation does not meet the requirement.

  121. Question 12129 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane's load chart indicates a rated capacity of 10,000 pounds for the configuration in use. Under 29 CFR 1926.1417, what is the maximum load the operator may lift?

    1. 110 percent of the rated capacity to account for dynamic effects
    2. The rated capacity, provided the load does not exceed the capacity for the configuration and the lift is within the manufacturer's limits Correct answer.
    3. The full 10,000 pounds under any conditions
    4. 75 percent of the rated capacity at all times

    Explanation

    Section 1926.1417 prohibits lifting loads in excess of the crane's rated capacity for the configuration, and the operator must ensure the load, including rigging, stays within the manufacturer's limits. The rated capacity already accounts for the configuration and must not be exceeded.

  122. Question 12229 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1416, what is the function of an operational aid such as a rated capacity limiter on a crane?

    1. It serves as the annual inspection record
    2. It warns or stops operations when the load approaches or exceeds the rated capacity Correct answer.
    3. It replaces the operator's obligation to know the load weight
    4. It automatically levels the crane on uneven ground

    Explanation

    Section 1926.1416 addresses operational aids that warn the operator or prevent operation when a limit is approached or exceeded, such as a rated capacity limiter. These devices supplement, but do not replace, the operator's judgment and knowledge of the load.

  123. Question 12329 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1433, when must a crane's load moment indicator be calibrated or adjusted?

    1. Only when the crane is first placed in service
    2. Only when the operator requests it
    3. After the crane has been assembled or reconfigured in a way that affects the indicator Correct answer.
    4. Every five years regardless of configuration changes

    Explanation

    Section 1926.1433 requires that operational aids such as load moment indicators be properly calibrated and adjusted after assembly or reconfiguration that affects their function. A crane assembled in a new configuration must have its aids set for that configuration before use.

  124. Question 12429 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.1441, what must be done before a crane is used to lift a load that exceeds its rated capacity with the use of a multiple-crane lift?

    1. The lift requires only a signal person at each crane
    2. The lift may proceed if the operator judges it safe
    3. The lift must be planned by a qualified person and the load distributed so that no crane exceeds its rated capacity Correct answer.
    4. The load may be lifted if the cranes are identical models

    Explanation

    Section 1926.1441 requires that multi-crane lifts be planned by a qualified person, with the load distributed so that no crane is loaded beyond its rated capacity for the configuration. The plan addresses the interaction of the cranes and the load.

  125. Question 12529 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.601, what is required of motor vehicles operating on a construction site?

    1. They must be inspected annually by a third party
    2. They must be equipped with a fire suppression system
    3. They must be operated only by employees holding a commercial driver's license
    4. They must be equipped with a backup alarm or be operated with a spotter when reversing Correct answer.

    Explanation

    Section 1926.601 requires that motor vehicles be equipped with an operable horn and, where the vehicle's reverse motion creates a hazard, an audible alarm or a spotter. Vehicles must also be maintained in safe operating condition.

  126. Question 12629 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A piece of mechanized equipment is left unattended on a slope at a construction site. Under 29 CFR 1926.600, what must be done to prevent the equipment from moving?

    1. The equipment must be attended at all times regardless of securing
    2. The equipment must be left in neutral with the parking brake released
    3. The equipment must be blocked or otherwise secured against motion Correct answer.
    4. The equipment may be left unsecured if the slope is less than 15 degrees

    Explanation

    Section 1926.600 requires that equipment be secured against inadvertent movement when left unattended, including blocking or other positive means on slopes. Leaving equipment in neutral with the brake released creates a hazard.

  127. Question 12729 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    Under 29 CFR 1926.605, which requirement applies to marine operations involving floating equipment and personnel transfer?

    1. Marine operations are exempt from Subpart O requirements
    2. Only the vessel captain determines whether life jackets are needed
    3. Personnel transfer may occur without regard to weather conditions
    4. Life saving equipment must be provided and personnel must be protected against falling overboard Correct answer.

    Explanation

    Section 1926.605 requires that marine operations provide life saving equipment, such as life jackets and ring buoys, and protect employees from falling overboard. The employer must also consider weather and water conditions when transferring personnel.

  128. Question 12829 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

    A crane must be operated near a 480-volt power line, and the employer decides to use the option of de-energizing and grounding the line. Under 29 CFR 1926.1408, what must occur before the crane may work within the minimum clearance distance?

    1. The operator must be notified verbally by the utility
    2. The crane must be equipped with an insulated boom
    3. The line must be marked with warning flags only
    4. The line must be confirmed de-energized and visibly grounded at the point of work Correct answer.

    Explanation

    Section 1926.1408 permits work closer than the minimum approach distance only when the line has been de-energized and visibly grounded at the point of work, or when other specified protective measures are used. Verbal assurance alone does not satisfy the requirement.

  129. Question 12929 CFR 1926 Subpart P: Excavations

    Under 29 CFR 1926.650, at what depth must an excavation be treated as requiring protective systems unless the excavation is made entirely in stable rock?

    1. 4 feet (1.2 m)
    2. 5 feet (1.5 m) Correct answer.
    3. 8 feet (2.4 m)
    4. 6 feet (1.8 m)

    Explanation

    Section 1926.650 defines an excavation as requiring protective systems when it reaches 5 feet in depth, unless the entire excavation is in stable rock. Below that depth, a competent person must still examine the ground for signs of instability.

  130. Question 13029 CFR 1926 Subpart P: Excavations

    Who is authorized to classify soil and to inspect excavations daily for evidence of conditions that could cause cave-ins?

    1. The competent person Correct answer.
    2. The registered professional engineer
    3. The site safety and health officer
    4. The project superintendent

    Explanation

    Subpart P assigns daily inspection and soil classification duties to the competent person, defined in 1926.650 as a person capable of identifying hazards and authorized to take prompt corrective action. A registered professional engineer is required only for certain designs, such as some timber shoring or shield systems.

  131. Question 13129 CFR 1926 Subpart P: Excavations

    An excavation is 20 feet deep and will use a support system designed by a registered professional engineer. Which statement reflects the Subpart P requirement for that design?

    1. The design is required only when the excavation exceeds 20 feet
    2. The design must be approved by the competent person before use
    3. The design may be verbal if the engineer remains on site
    4. The design must be in writing and kept at the worksite during construction Correct answer.

    Explanation

    Section 1926.652(b) requires that designs for support systems, shield systems, and other protective systems be in writing and kept at the worksite while the system is installed and used. The written record lets the competent person verify that field conditions match the design assumptions.

  132. Question 13229 CFR 1926 Subpart P: Excavations

    A trench is 12 feet deep with vertical walls and no protective system. Which statement best describes the access and egress obligation in addition to the protective system requirement?

    1. Ladders or other safe means must be located so no worker travels more than 25 feet laterally Correct answer.
    2. A single ladder at the trench entrance satisfies the rule for the whole length
    3. Ladders are required only if workers must carry tools
    4. Ramps are prohibited in trenches deeper than 10 feet

    Explanation

    Section 1926.651(l) requires stairways, ladders, ramps, or other safe means of egress in excavations 4 feet or deeper, spaced so that lateral travel is no more than 25 feet. The 25-foot spacing applies regardless of tool carrying.

  133. Question 13329 CFR 1926 Subpart P: Excavations

    Which of the following correctly states the general requirement for spoil piles and equipment near the edge of an excavation?

    1. Spoil must be kept at least 2 feet from the edge, and equipment must be kept back far enough to prevent surcharge loading Correct answer.
    2. Spoil and equipment must be kept at least 10 feet from the edge in all soils
    3. Spoil and equipment must be kept at least 2 feet from the edge
    4. Spoil may be piled at the edge if the competent person allows it

    Explanation

    Section 1926.651(j)(2) requires spoil, materials, and equipment to be kept at least 2 feet from the excavation edge, and equipment and other loads must be kept back far enough that they do not cause a collapse. The distance for equipment depends on soil and load, not a fixed number.

  134. Question 13429 CFR 1926 Subpart P: Excavations

    Workers are installing a utility line in a 7-foot-deep trench cut through previously disturbed fill. Which action best reflects the Subpart P requirement before workers enter?

    1. Use sloping only, since shoring is not permitted in fill
    2. Rely on the angle of repose of the original undisturbed soil
    3. Have the competent person classify the soil and select a protective system Correct answer.
    4. Assume Type B soil because the trench is shallow

    Explanation

    Section 1926.652 requires that employees in excavations be protected from cave-ins by a protective system, and the competent person must classify the soil to choose it. Previously disturbed soil is generally treated as Type C unless testing shows otherwise.

  135. Question 13529 CFR 1926 Subpart P: Excavations

    Which soil type has the lowest allowable unconfined compressive strength and therefore typically demands the most conservative sloping?

    1. Type C Correct answer.
    2. Stable rock
    3. Type B
    4. Type A

    Explanation

    Type C soil has an unconfined compressive strength of 0.5 tons per square foot or less and is the least stable classification, requiring the flattest slopes. Type A is the most stable soil classification, and stable rock allows vertical walls.

  136. Question 13629 CFR 1926 Subpart P: Excavations

    A competent person observes that a trench wall is cracking and the spoil pile is sliding toward the excavation. What is the required immediate action?

    1. Increase the depth of the trench to relieve pressure
    2. Remove employees from the excavation until the hazard is corrected Correct answer.
    3. Continue work and re-inspect at the end of the shift
    4. Add a second ladder to shorten egress distance

    Explanation

    Section 1926.651(k)(2) requires that employees be removed from an excavation when the competent person finds evidence of a situation that could result in a cave-in, slide, or other dangerous condition. Work resumes only after the condition is corrected.

  137. Question 13729 CFR 1926 Subpart P: Excavations

    Which practice is specifically required when mobile equipment operates adjacent to an excavation where employees are exposed?

    1. The operator must use warning devices such as barricades or hand signals Correct answer.
    2. A stop log or barricade must be installed at the edge
    3. Equipment must be shut down whenever a worker is in the trench
    4. Employees must wear high-visibility vests at all times

    Explanation

    Section 1926.651(f) requires that employees exposed to vehicular traffic wear warning vests, and 1926.651(g) requires warning systems for mobile equipment operating near excavations. Barricades, stop logs, or hand signals warn operators and workers of the edge and of each other.

  138. Question 13829 CFR 1926 Subpart P: Excavations

    An excavation is made in stable rock and is 15 feet deep. What does Subpart P require regarding protective systems?

    1. A protective system is required because the depth exceeds 5 feet
    2. Sloping at 3/4:1 is required regardless of material
    3. Shoring is required because the depth exceeds 10 feet
    4. No protective system is required because the excavation is entirely in stable rock Correct answer.

    Explanation

    Section 1926.652(a)(1) exempts excavations made entirely in stable rock from the protective system requirement. The competent person must still determine that the rock is stable and inspect for deterioration or loose material.

  139. Question 13929 CFR 1926 Subpart P: Excavations

    For Type B soil, which maximum allowable slope is specified in Appendix B to Subpart P for excavations less than 20 feet deep?

    1. 1 1/2:1
    2. 2:1
    3. 1:1 Correct answer.
    4. 3/4:1 (horizontal to vertical)

    Explanation

    Appendix B lists a maximum allowable slope of 1:1 for Type B soil, meaning one unit horizontal for each unit vertical. Type A permits 3/4:1 and Type C requires 1 1/2:1.

  140. Question 14029 CFR 1926 Subpart P: Excavations

    A trench box is used in a 14-foot-deep trench. Which requirement applies to the box under Subpart P?

    1. The box must be removed before workers enter to verify soil conditions
    2. The box must extend from the bottom of the trench to the top of the excavation or be installed per the manufacturer's tabulated data Correct answer.
    3. The box must be approved by the competent person in writing
    4. The box may be placed with its top at any height as long as the bottom is at trench bottom

    Explanation

    Section 1926.652(g) requires shield systems to extend from the bottom of the excavation to the top, or to be installed per the manufacturer's tabulated data or a registered professional engineer's design. This prevents soil from sloughing behind the shield.

  141. Question 14129 CFR 1926 Subpart P: Excavations

    Which condition would disqualify soil from being classified as Type A under Appendix A to Subpart P?

    1. The soil is fissured Correct answer.
    2. The soil is cohesive with an unconfined compressive strength of 1.5 tons per square foot
    3. The soil was previously disturbed but reconsolidated
    4. The soil contains no visible water

    Explanation

    Appendix A lists fissured soil as a condition that prevents classification as Type A, along with soil that has been previously disturbed, is subject to vibration, or has other destabilizing factors. Cohesive soil with sufficient strength is otherwise eligible.

  142. Question 14229 CFR 1926 Subpart P: Excavations

    A worker must enter a 6-foot-deep excavation where the atmosphere may contain a hazardous gas. What does Subpart P require before entry?

    1. Only confined space entry procedures apply, so Subpart P testing is not required
    2. The atmosphere must be tested and, if hazardous, ventilated or respiratory protection provided Correct answer.
    3. The competent person may rely on the absence of odor
    4. Testing is required only if the excavation is deeper than 10 feet

    Explanation

    Section 1926.651(g)(1) requires testing for oxygen deficiency and hazardous gases before employees enter excavations where such atmospheres could exist, and requires ventilation or respiratory protection when hazards are found. Odor is not a reliable indicator.

  143. Question 14329 CFR 1926 Subpart P: Excavations

    Water is accumulating at the bottom of an excavation. What is the required response under Subpart P?

    1. Suspend all work until the water evaporates naturally
    2. Take appropriate precautions such as removing water and inspecting for stability before allowing work Correct answer.
    3. Use a pump only if the competent person is present
    4. Continue work if the water is less than 6 inches deep

    Explanation

    Section 1926.651(h) requires that employees not work in excavations where water is accumulating unless adequate precautions are taken, such as removing the water and inspecting the walls for instability. Water reduces soil strength and increases cave-in risk.

  144. Question 14429 CFR 1926 Subpart P: Excavations

    An excavation is adjacent to a building foundation. What does Subpart P require regarding the stability of that structure?

    1. Support systems such as shoring, bracing, or underpinning must be provided to protect the structure Correct answer.
    2. A registered professional engineer must inspect the building daily
    3. The building must be evacuated until the excavation is backfilled
    4. The excavation must be offset at least 10 feet from the foundation

    Explanation

    Section 1926.651(i)(1) requires support systems to protect adjacent structures whose stability is endangered by the excavation. The competent person determines whether the excavation could weaken the foundation and what support is needed.

  145. Question 14529 CFR 1926 Subpart P: Excavations

    A competent person is choosing between sloping and shoring for a deep excavation in Type C soil. Which consideration is most consistent with Subpart P?

    1. The choice may be made by the equipment operator on site
    2. Shoring may be used, but the system must be designed and installed to resist the expected loads Correct answer.
    3. Shoring is prohibited in Type C soil because the soil cannot support it
    4. Sloping is always preferred because it requires no design

    Explanation

    Section 1926.652(b) allows sloping, benching, shoring, or shielding, but any support system must be designed to resist the loads and installed per the standard. Type C soil is weak, so shoring must be engineered or selected from tabulated data.

  146. Question 14629 CFR 1926 Subpart P: Excavations

    Which statement correctly describes the daily inspection obligation for excavations under 1926.651(k)?

    1. Inspections are required only after a cave-in occurs
    2. Inspections are required weekly and after any rain
    3. Inspections are required only when the excavation exceeds 10 feet
    4. Inspections are required at the start of each shift and as needed throughout the shift Correct answer.

    Explanation

    Section 1926.651(k)(1) requires a competent person to inspect excavations and adjacent areas at the start of each shift and as needed throughout the shift. The inspection covers protective systems, adjacent structures, and evidence of instability.

  147. Question 14729 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under 29 CFR 1926 Subpart Q, at what minimum compressive strength must concrete formwork supports remain in place unless the employer demonstrates otherwise?

    1. Until the concrete has cured for 24 hours
    2. Until the concrete reaches 500 psi
    3. Until the concrete surface is dry to the touch
    4. Until the concrete attains the strength that supports the loads imposed Correct answer.

    Explanation

    Subpart Q requires that forms be supported until the concrete has gained sufficient strength to carry the imposed loads on its own. Time or surface appearance alone is not a reliable indicator, so the employer must verify strength by test or by a documented equivalent method.

  148. Question 14829 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    When employees are required to work more than 5 feet above a concrete formwork deck that is not yet self-supporting, what does Subpart Q require?

    1. A personal fall arrest system anchored to the form
    2. Guardrails or a personal fall arrest system Correct answer.
    3. A safety monitoring system alone
    4. A warning line at 6 feet from the edge

    Explanation

    Subpart Q requires fall protection for employees exposed to falls while erecting or working on formwork, satisfied by guardrails or a personal fall arrest system. A warning line or monitor alone is not an acceptable substitute for the fall distances involved here.

  149. Question 14929 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    A masonry wall is being constructed and the employer needs to know the minimum lateral bracing requirement during construction. Which statement reflects the Subpart Q rule?

    1. Bracing is optional if the wall is reinforced
    2. Bracing is required only when wind speeds exceed 40 mph
    3. Walls must be braced to resist wind and other lateral loads during construction Correct answer.
    4. Walls over 8 feet must be braced only after the day's work ends

    Explanation

    Subpart Q requires that masonry walls be supported and braced to withstand wind and other lateral forces during construction, before permanent structural elements are in place. Bracing must be designed for the loads anticipated, not deferred until the shift ends.

  150. Question 15029 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under 29 CFR 1926 Subpart R, a controlled decking zone (CDZ) may be established only in which situation?

    1. When performing bolt-up work at heights above 15 feet
    2. When installing metal decking in areas where work is being performed from a working platform Correct answer.
    3. When erecting structural steel columns over 30 feet
    4. When removing decking during demolition

    Explanation

    A CDZ is a defined area where initial metal decking is installed and where conventional fall protection is impractical; Subpart R limits its use to that specific decking work. Access to the CDZ must be controlled and only trained decking crews admitted.

  151. Question 15129 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    A steel erection crew is connecting beams at 22 feet above grade. Which fall protection approach is permitted under Subpart R for connectors?

    1. No fall protection is required for connectors
    2. A fall protection system, or a fall protection plan with a controlled decking zone Correct answer.
    3. A safety net installed only after the deck is complete
    4. A warning line system around the perimeter

    Explanation

    Subpart R allows connectors to use conventional fall protection or to work under a site-specific fall protection plan meeting the standard's requirements. The plan must address procedures, training, and controlled access for the connector work.

  152. Question 15229 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart R, when must anchor rods be inspected and determined to be adequate for the intended load?

    1. During the final inspection walk
    2. After the first steel members are erected
    3. Only after concrete reaches 28-day strength
    4. Before the steel erection begins Correct answer.

    Explanation

    The standard requires that anchor rods be inspected and accepted as adequate before erection proceeds, since they transfer column loads to the foundation. Deficiencies discovered after erection create an immediate collapse hazard.

  153. Question 15329 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    In underground construction under Subpart S, how often must a competent person inspect the work area and the atmosphere?

    1. Weekly, unless a hazard is reported
    2. As often as necessary to ensure safety, and at least as specified for hazardous conditions Correct answer.
    3. Only after a cave-in or gas alarm
    4. Once per shift at the start

    Explanation

    Subpart S requires frequent and regular inspection by a competent person, with the frequency determined by conditions such as changing ground or gas readings. The inspections must be documented and must precede work after any hazardous event.

  154. Question 15429 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    An underground construction site uses a hoist for personnel. Under Subpart S, which practice is required?

    1. A signal system is optional when the shaft is shallow
    2. Personnel hoisting must use equipment and procedures specifically approved for employee transport Correct answer.
    3. Hoisting speed may be increased at the operator's discretion
    4. Personnel may ride with materials if the cage is enclosed

    Explanation

    Subpart S requires that personnel hoisting use equipment designed and approved for that purpose, with proper signaling, gates, and limiting devices. Mixing personnel with material loads or bypassing signals undermines the safeguards.

  155. Question 15529 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Before demolition begins under Subpart T, what must the employer do regarding utilities?

    1. Leave utilities energized for lighting during demolition
    2. Assume utilities are dead unless marked
    3. Notify the utility only after demolition starts
    4. Locate, shut off, and cap or otherwise control utilities to the extent feasible Correct answer.

    Explanation

    Subpart T requires that utility services be located, shut off, and controlled before demolition so that workers are not exposed to electrical, gas, or water hazards. Notification and verification steps must be completed in advance.

  156. Question 15629 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    During demolition of a multistory structure, when must an engineered survey of the structure be conducted?

    1. After the first floor is removed
    2. Only when explosives are used
    3. Only if the building exceeds 10 stories
    4. Before demolition begins, to determine the sequence and hazards Correct answer.

    Explanation

    Subpart T requires a survey of the structure before demolition to determine the condition of the framing, floors, and walls and to plan the demolition sequence. The survey informs the engineering survey and the written demolition plan.

  157. Question 15729 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart T, what is the required minimum distance for a debris drop area from an exterior wall when debris is dropped through a chute?

    1. The area must be enclosed or barricaded and the chute must extend to the ground or a debris container
    2. No fixed numerical setback is specified Correct answer.
    3. Only a warning sign is required
    4. Debris may be dropped freely if a spotter is present

    Explanation

    Subpart T does not specify a fixed numerical setback from an exterior wall for an area receiving debris through a chute. Effective area protection and chute discharge controls are still required, including closure of the discharge area when operations are not in progress.

  158. Question 15829 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart U, who may handle and use explosives on a jobsite?

    1. The general contractor's safety officer
    2. Only qualified persons, and blasting must be under the direction of a competent blaster Correct answer.
    3. Any foreman on the crew
    4. Any employee who has completed general site orientation

    Explanation

    Subpart U restricts explosive handling to qualified personnel under the direction of a competent blaster, with blasting conducted per the standard's requirements. Access to explosive storage and loading areas must be limited to authorized persons.

  159. Question 15929 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Before firing a blast under Subpart U, what warning signal sequence is required?

    1. No warning is required if the area is posted
    2. An audible warning sufficient to alert employees, followed by a waiting period before firing Correct answer.
    3. A radio call to the office only
    4. A single long horn blast only

    Explanation

    Subpart U requires an audible warning signal and a sufficient interval before firing so that employees can reach safety. A posted sign or office notification does not substitute for an on-site audible warning.

  160. Question 16029 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    After a blast, when may employees return to the blast area?

    1. When the blaster has inspected the area and determined it is safe Correct answer.
    2. Immediately after the smoke clears
    3. After 5 minutes regardless of inspection
    4. When the equipment operator signals

    Explanation

    Subpart U requires that the blaster inspect the blast area after firing and determine that no misfire or other hazard remains before employees are allowed to return. Visual clearance of smoke is not a reliable safety indicator.

  161. Question 16129 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart V, what is the minimum approach distance concept intended to protect against?

    1. Radio frequency interference
    2. Arc flash from switching operations only
    3. Mechanical damage to conductors
    4. Electrical contact and arc hazards when working near energized lines Correct answer.

    Explanation

    Minimum approach distances establish a safe separation from energized parts to prevent electrical contact and arc exposure. The distances account for voltage, switching surges, and inadvertent movement.

  162. Question 16229 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    When work is performed near energized lines under Subpart V, which control is required if the lines cannot be de-energized?

    1. A verbal warning to the crew only
    2. Isolation, insulation, or distance controls appropriate to the voltage Correct answer.
    3. Insulated tools alone with no other controls
    4. Grounding the lines while energized

    Explanation

    Subpart V requires that energized-line work use protective controls such as isolation, insulation, or maintaining the minimum approach distance for the voltage involved. A warning alone does not prevent contact.

  163. Question 16329 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart W, rollover protective structures (ROPS) and seat belts are required on which equipment?

    1. Only equipment over 10 tons
    2. Equipment operated by a certified operator
    3. Only equipment operated on public roads
    4. All equipment covered by the standard that exposes the operator to rollover hazards Correct answer.

    Explanation

    Subpart W requires ROPS and seat belts on covered equipment such as certain agricultural and construction tractors and loaders to protect operators in a rollover. Exemptions are narrow and based on equipment type, not weight or operator certification.

  164. Question 16429 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders

    Under Subpart X, what is the minimum height at which stairrails are required on a stairway?

    1. Only stairways over 8 feet total rise
    2. Only temporary stairways
    3. Any stairway with two or more risers
    4. Stairways with more than four risers or rising more than 30 inches Correct answer.

    Explanation

    Subpart X requires stairrails on stairways having more than four risers or rising more than 30 inches, whichever is less, with a rail on each open side. The rule applies to both temporary and permanent stairways during construction.

  165. Question 16529 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Under 29 CFR 1926.1153, what is the permissible exposure limit (PEL) for respirable crystalline silica, expressed as an 8-hour time-weighted average?

    1. 50 micrograms per cubic meter of air Correct answer.
    2. 25 micrograms per cubic meter of air
    3. 100 micrograms per cubic meter of air
    4. 250 micrograms per cubic meter of air

    Explanation

    The construction silica standard sets the PEL at 50 micrograms per cubic meter of air averaged over an 8-hour shift. This is roughly half the older formula-based limit and matches the action level trigger point for exposure monitoring.

  166. Question 16629 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    What is the action level for respirable crystalline silica under 29 CFR 1926.1153, and what does it trigger?

    1. 25 micrograms per cubic meter as an 8-hour TWA, triggering exposure assessment obligations Correct answer.
    2. 10 micrograms per cubic meter as a 15-minute short-term exposure limit
    3. 100 micrograms per cubic meter as an 8-hour TWA, triggering medical surveillance
    4. 50 micrograms per cubic meter as an 8-hour TWA, triggering immediate respirator use

    Explanation

    The action level is 25 micrograms per cubic meter as an 8-hour TWA. Reaching or exceeding it obligates the employer to assess exposures and, if the PEL is exceeded, to implement controls and offer medical surveillance.

  167. Question 16729 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    An employer fully implements the engineering controls and work practices in Table 1 for a handheld grinder used outdoors. What is the resulting obligation regarding exposure monitoring for that task?

    1. Monitoring is required only if the employee requests it in writing
    2. Only a personal breathing zone sample over 15 minutes is required
    3. No additional exposure assessment is required for that task Correct answer.
    4. Air monitoring must be performed quarterly regardless of controls

    Explanation

    Table 1 provides specified engineering controls, work practices, and respiratory protection for common construction tasks. When an employer fully and properly implements the Table 1 entry, no additional exposure assessment is required for that task.

  168. Question 16829 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    When an employer does not use Table 1 and instead performs an exposure assessment, within what period must the assessment be repeated if results indicate exposures at or above the action level?

    1. Every six months Correct answer.
    2. Every three years
    3. Every five years
    4. Every twelve months

    Explanation

    Where the initial assessment shows exposures at or above the action level, the employer must repeat monitoring at least every six months. If results are below the action level, reassessment may be discontinued under specified conditions.

  169. Question 16929 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Which written program element is specifically required by the hazard communication standard at 29 CFR 1926.59?

    1. A written hearing conservation program for equipment operators
    2. A written emergency action plan for every jobsite
    3. A written respiratory protection program for all site visitors
    4. A written hazard communication program covering labels, SDSs, and employee training Correct answer.

    Explanation

    Construction employers must develop and maintain a written hazard communication program addressing container labeling, safety data sheet availability, and employee information and training. The other programs are triggered by different standards and hazards, not by HazCom.

  170. Question 17029 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    A drum of solvent is transferred from a labeled 55-gallon container into a smaller portable container for use by one employee during the shift. Under 1926.59, what labeling is required?

    1. No label is required if the material is used by that employee within the work shift Correct answer.
    2. The portable container must be labeled with the manufacturer's address
    3. The portable container must bear a full NFPA diamond
    4. The portable container must carry a copy of the safety data sheet

    Explanation

    Portable containers used by one employee within a single shift are exempt from labeling under the hazard communication standard. Once the material is left unattended or transferred to another worker, labeling is required.

  171. Question 17129 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    What information must a workplace label on a hazardous chemical container convey under the revised hazard communication standard?

    1. Product identifier, manufacturer phone number, and lot code
    2. Chemical name, CAS number, and flash point only
    3. Product identifier and hazard statements, pictograms, and signal word Correct answer.
    4. Trade secret status and the date of manufacture

    Explanation

    Workplace labels must include the product identifier and generally the pictograms, signal word, and hazard statements. This aligns workplace labeling with the global harmonized system elements required on shipped containers.

  172. Question 17229 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Under 29 CFR 1926.59, how many sections must a compliant safety data sheet contain?

    1. 8
    2. 16 Correct answer.
    3. 12
    4. 10

    Explanation

    Safety data sheets must follow the 16-section format established under the revised hazard communication standard. The sections cover identification, hazards, composition, first aid, firefighting, handling, and related information.

  173. Question 17329 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    An employer stores hazardous chemicals on a multi-employer site. What does 1926.59 require regarding safety data sheets for employees who must work in areas where they may be exposed?

    1. SDSs must be posted on a public bulletin board outside the site
    2. SDSs must be readily accessible during each work shift when employees are in the area Correct answer.
    3. SDSs may be kept in a locked office available only to supervisors
    4. SDSs may be replaced by verbal warnings from the competent person

    Explanation

    Safety data sheets must be readily accessible to employees during each work shift in their work areas. Locking them away or replacing them with verbal warnings defeats the standard's access requirement.

  174. Question 17429 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Which hazard is addressed by 29 CFR 1926.62 in construction work?

    1. Benzene exposure during tank cleaning
    2. Formaldehyde exposure in plywood manufacturing
    3. Lead exposure during activities such as torch cutting of painted steel Correct answer.
    4. Asbestos exposure during brake servicing

    Explanation

    Section 1926.62 is the construction lead standard, covering activities such as demolition, torch cutting, and abrasive blasting on lead-painted surfaces. It sets a PEL of 50 micrograms per cubic meter as an 8-hour TWA and requires medical surveillance at trigger levels.

  175. Question 17529 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Under 29 CFR 1926.62, what is the permissible exposure limit for lead in construction?

    1. 25 micrograms per cubic meter as an 8-hour TWA
    2. 50 micrograms per cubic meter as an 8-hour TWA Correct answer.
    3. 100 micrograms per cubic meter as an 8-hour TWA
    4. 30 micrograms per cubic meter as an 8-hour TWA

    Explanation

    The construction lead standard sets the PEL at 50 micrograms per cubic meter averaged over eight hours. An action level of 30 micrograms per cubic meter triggers exposure monitoring obligations.

  176. Question 17629 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Which element is required in a hazard communication training program for construction employees?

    1. A copy of the employer's insurance certificate
    2. A signed waiver from each employee accepting chemical risks
    3. A list of every chemical the employer has ever used
    4. Explanation of how to detect the presence or release of a hazardous chemical Correct answer.

    Explanation

    HazCom training must cover methods to detect a release, the hazards of chemicals present, protective measures, and details of the employer's written program. A historical inventory or liability waiver is not a training element.

  177. Question 17729 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    An employee performs a task covered by Table 1 that specifies a respirator as part of the control package. What must the employer do before requiring that respirator use?

    1. Establish a written respiratory protection program under 1926.103 Correct answer.
    2. Conduct a noise survey of the work area
    3. Post the Table 1 entry at the site entrance
    4. Notify the local fire department

    Explanation

    Whenever respirators are required, including as part of a Table 1 control package, the employer must implement a respiratory protection program under 1926.103. That program includes medical evaluation, fit testing, and training.

  178. Question 17829 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Which statement correctly describes the medical surveillance obligation for respirable crystalline silica under 1926.1153?

    1. It is required only when exposures exceed the PEL for 60 days per year
    2. It must be offered to every employee on the site regardless of exposure
    3. It is required only after an employee shows symptoms of silicosis
    4. It must be offered when exposure is at or above the PEL for 30 or more days per year Correct answer.

    Explanation

    The silica standard requires the employer to offer medical surveillance when an employee is exposed at or above the PEL for 30 or more days in a 12-month period. The surveillance includes a medical and work history, physical exam, and tuberculosis testing.

  179. Question 17929 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    What does the hazard communication standard say about chemical trade secrets in relation to employee access to hazard information?

    1. Only the manufacturer may decide whether employees see hazard information
    2. The employer may withhold all SDS information from employees permanently
    3. The employer must disclose the specific chemical identity under defined conditions such as medical necessity Correct answer.
    4. Trade secret status eliminates any obligation to provide hazard information

    Explanation

    Trade secret protection does not eliminate hazard communication duties. Under specified conditions, such as a medical necessity, the specific chemical identity must be disclosed while other protections may apply.

  180. Question 18029 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Which of the following is a required element of the written hazard communication program for a construction employer?

    1. A schedule of employee vacation days
    2. A roster of employees' home addresses
    3. A copy of the site's stormwater permit
    4. A list of the hazardous chemicals present at the site Correct answer.

    Explanation

    The written program must include a list of the hazardous chemicals known to be present using an identity that can be cross-referenced to the SDS. It must also describe labeling, SDS access, and training methods.

  181. Question 18129 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    An employer chooses to rely on objective data to demonstrate that a task cannot release respirable crystalline silica above the action level. What must that data reflect?

    1. General industry averages for all construction trades
    2. Only exposures measured at a different company's facility
    3. Results from a single personal sample taken in a parking lot
    4. Exposures associated with the specific task, material, and conditions of use Correct answer.

    Explanation

    Objective data must demonstrate that the product, material, or task cannot release silica at or above the action level under expected conditions of use. Generic averages or unrelated sampling do not satisfy this requirement.

  182. Question 18229 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

    Under 29 CFR 1926.1153, what is the required frequency for exposure monitoring when the initial assessment shows exposures above the PEL?

    1. Every six months
    2. Every three months Correct answer.
    3. Every twelve months
    4. Every twenty-four months

    Explanation

    When exposures exceed the PEL, the employer must repeat monitoring at least every three months. At or above the action level but below the PEL, reassessment is required every six months.

  183. Question 183Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    Under OSHA recordkeeping rules, a case must be recorded on the OSHA 300 Log when it results in death, days away from work, restricted work or transfer to another job, medical treatment beyond first aid, loss of consciousness, or which of the following?

    1. Any injury that the employee reports to a first-aid station
    2. A significant injury or illness diagnosed by a physician or other licensed health care professional Correct answer.
    3. Any near-miss incident in which no one was hurt
    4. Any injury requiring a workplace safety committee review

    Explanation

    The recording criteria in 29 CFR 1904.7 include death, days away, restricted work or transfer, medical treatment beyond first aid, loss of consciousness, and a significant injury or illness diagnosed by a physician or other licensed health care professional. Near-misses and first-aid-only cases are not recordable.

  184. Question 184Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employer with 11 employees at a single establishment must complete the OSHA 300A Summary of Work-Related Injuries and Illnesses. What is the minimum posting requirement for that form?

    1. Post it for 30 calendar days after the end of the calendar year
    2. Post it continuously for the entire following calendar year
    3. Post it from February 1 through April 30 of the following year Correct answer.
    4. Post it only during the month of January

    Explanation

    Under 29 CFR 1904.32, the annual summary must be posted no later than February 1 and kept posted until April 30 of the year following the year covered. A 30-day or single-month posting period does not satisfy the rule.

  185. Question 185Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    Which of the following best describes the hierarchy of controls used to select hazard abatement measures?

    1. Elimination, substitution, engineering controls, administrative controls, then personal protective equipment Correct answer.
    2. Personal protective equipment, administrative controls, engineering controls, substitution, then elimination
    3. Administrative controls, elimination, personal protective equipment, substitution, then engineering controls
    4. Engineering controls, personal protective equipment, elimination, administrative controls, then substitution

    Explanation

    The recognized hierarchy ranks controls from most to least effective: elimination, substitution, engineering controls, administrative controls, and finally PPE. PPE is last because it protects only the wearer and depends on correct use.

  186. Question 186Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employee suffers a needlestick injury at work and, after evaluation, is found to have contracted a bloodborne infection that was not present before the exposure. How should this be handled on the OSHA 300 Log?

    1. Record it only if the employee misses more than three days of work
    2. Do not record it because infections are not injuries
    3. Record it as a confirmed case of a work-related illness, since the infection is a new case diagnosed after the exposure Correct answer.
    4. Record it as a first-aid case and note the treatment on the log

    Explanation

    A significant diagnosed illness that is work-related is recordable even if it develops after the exposure event. The needlestick itself may already be recordable, and the resulting infection is tracked as a work-related illness case.

  187. Question 187Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A company wants to build an effective safety and health program. Which element most directly supports the practice of identifying and correcting hazards before they cause harm?

    1. A bonus plan tied to the number of injuries reported
    2. A safety poster campaign posted in the break room
    3. A systematic worksite analysis that includes inspections, incident reviews, and job hazard analysis Correct answer.
    4. A discipline policy that penalizes employees who report hazards

    Explanation

    Worksite analysis is the program element that systematically finds hazards through inspections, job hazard analysis, and review of incidents and near-misses. It feeds the hazard prevention and control step where corrections are made.

  188. Question 188Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employer has 9 employees at one location. Under OSHA injury and illness recordkeeping, what is the general obligation for this establishment?

    1. The employer is partially exempt from routine 300 Log maintenance unless OSHA or the Bureau of Labor Statistics requests records in writing Correct answer.
    2. The employer must keep the 300 Log only for injuries involving days away from work
    3. The employer must maintain the 300 Log but is exempt from the 300A posting
    4. The employer is fully exempt from all recordkeeping and reporting duties

    Explanation

    Establishments with 10 or fewer employees at all times during the prior calendar year are partially exempt from routinely keeping OSHA injury and illness records. They must still report fatalities, in-patient hospitalizations, amputations, and eye losses, and must provide records if asked in writing.

  189. Question 189Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A worker dies 20 days after a work-related incident. What is the employer's reporting obligation to OSHA?

    1. Report the fatality within 30 days of the death
    2. Report the fatality to OSHA within 8 hours of learning of the death Correct answer.
    3. Report the fatality only on the annual 300A summary
    4. Report the fatality within 24 hours of the incident

    Explanation

    Under 29 CFR 1904.39, a work-related fatality must be reported within 8 hours of the employer learning of it, even when death occurs up to 30 days after the incident. Reporting is separate from and in addition to logging the case.

  190. Question 190Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employee is hospitalized for observation after a workplace incident but is released the same day without being admitted as an in-patient. How does this affect the employer's 8-hour/24-hour reporting duty?

    1. No in-patient hospitalization report is required because the employee was not formally admitted for treatment Correct answer.
    2. A report is required only if the employee later returns for follow-up care
    3. A report is required because any emergency room visit counts as hospitalization
    4. A report is required because the employee missed the rest of the shift

    Explanation

    The 24-hour reporting requirement applies to in-patient hospitalization for treatment, not to emergency room observation or diagnostic visits. A same-day release without admission does not trigger the report, though the case may still be recordable on the log.

  191. Question 191Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    Which situation correctly describes a case involving restricted work activity for OSHA recordkeeping?

    1. The employee returns to work but cannot perform all routine job functions for part of the day, as directed by a physician Correct answer.
    2. The employee is absent for two days and then returns to full duty
    3. The employee receives a bandage and returns to normal duties
    4. The employee performs normal duties but takes a pain reliever during the shift

    Explanation

    Restricted work occurs when a physician or other licensed health care professional recommends that the worker not perform routine functions or not work a full day. Taking medication or receiving first aid while working normally does not create restricted work.

  192. Question 192Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A safety manager is deciding how to control a noise hazard that exceeds the permissible exposure limit. Which approach reflects the most effective control that should be considered first?

    1. Post warning signs and provide annual audiometric testing
    2. Substitute quieter equipment or enclose the noise source with engineering controls Correct answer.
    3. Require hearing protection and rotate workers to limit exposure duration
    4. Institute a hearing conservation training program for all staff

    Explanation

    Engineering controls such as substitution, enclosure, or isolation address the hazard at its source and rank above administrative controls and PPE. Hearing protection, rotation, signage, and training are lower-level controls used when source controls are not feasible.

  193. Question 193Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A company's injury rate is falling, but employees say they are discouraged from reporting. Which program evaluation approach best tests whether the decline reflects real improvement rather than underreporting?

    1. Check that all supervisors completed the required recordkeeping training
    2. Rely solely on the OSHA 300 Log totals for the last three years
    3. Confirm that the 300A summary was posted on time
    4. Compare reported injury trends with independent indicators such as near-miss reports, inspection findings, and employee interviews Correct answer.

    Explanation

    Triangulating injury data with near-miss reporting, inspection results, and direct employee input helps detect reporting suppression. A declining log alone cannot distinguish genuine improvement from underreporting.

  194. Question 194Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A worker's pre-existing condition is aggravated by a workplace event, causing lost time. Under OSHA recordkeeping, how should the employer generally treat the case?

    1. Never record it because the underlying condition was not caused by work
    2. Record it if a workplace event or exposure significantly aggravated the pre-existing condition Correct answer.
    3. Record it only if the aggravation lasts more than 30 days
    4. Record it only if the worker files a workers' compensation claim

    Explanation

    The recordkeeping rule covers work-related injuries and illnesses, including significant aggravation of a pre-existing condition by a workplace event or exposure. The original condition need not be work-related for the aggravation to be recordable.

  195. Question 195Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employer must decide whether an injury is work-related. Which principle governs the determination?

    1. An injury is work-related if an event or exposure in the work environment caused or contributed to the injury or significantly aggravated a prior condition Correct answer.
    2. An injury is work-related only if the employee was performing assigned job tasks at the time
    3. An injury is work-related only if a supervisor witnessed the event
    4. An injury is work-related only if it occurs on the employer's premises during scheduled hours

    Explanation

    The work-relatedness test asks whether an event or exposure in the work environment caused or contributed to the injury or illness, or significantly aggravated a prior condition. Location, witnesses, and task assignment are not the controlling test.

  196. Question 196Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    What is the primary purpose of the OSHA Form 301 Injury and Illness Incident Report?

    1. To report fatalities and hospitalizations to OSHA within 8 or 24 hours
    2. To summarize annual injury totals for posting
    3. To list employees who are partially exempt from recordkeeping
    4. To capture detailed information about each recorded case, such as how the injury occurred and the object or substance involved Correct answer.

    Explanation

    The Form 301 collects case-specific details, including the circumstances, the object or substance involved, and the nature of the injury or illness. It supports the 300 Log entry and is retained for five years.

  197. Question 197Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    How long must an employer retain OSHA injury and illness records such as the 300 Log and 301 Incident Reports?

    1. Three years after the case is closed
    2. Indefinitely for the life of the establishment
    3. One year after the record is created
    4. Five years following the end of the calendar year that the records cover Correct answer.

    Explanation

    Under 29 CFR 1904.33, the 300 Log, 300A, and 301 forms must be retained for five years following the end of the calendar year they cover. Updates to the log may be needed during that period.

  198. Question 198Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A safety professional is developing a new program and wants to ensure management commitment is visible. Which action best demonstrates that commitment?

    1. Managers display the injury rate on a bulletin board each quarter
    2. Managers distribute a safety handbook once at orientation
    3. Managers participate in safety inspections and hold themselves accountable for correcting identified hazards Correct answer.
    4. Managers delegate all safety duties to the safety committee

    Explanation

    Visible leadership involvement, such as participating in inspections and being accountable for hazard correction, demonstrates genuine management commitment. One-time handouts, full delegation, and posting statistics alone do not show active engagement.

  199. Question 199Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    An employee reports a hazard, and the employer corrects it. Which follow-up practice best strengthens the hazard identification and control process?

    1. Close the item once a work order is issued
    2. Assign the report to the employee who raised it for resolution
    3. Track the hazard through to verified correction and communicate the resolution back to the reporting employee Correct answer.
    4. File the report without further review if the hazard seems minor

    Explanation

    Effective hazard control verifies that the correction was actually made and closes the loop with the reporter, which builds trust and encourages future reporting. Issuing a work order or filing the report does not confirm the hazard was abated.

  200. Question 200Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

    A partially exempt employer learns that an employee suffered a work-related amputation. What must the employer do?

    1. Report the amputation to OSHA within 24 hours, even though the establishment is otherwise partially exempt Correct answer.
    2. Report the amputation only on the next annual 300A summary
    3. Take no action because partial exemption covers all reporting duties
    4. Report the amputation within 8 hours as if it were a fatality

    Explanation

    Partially exempt establishments must still report fatalities within 8 hours and in-patient hospitalizations, amputations, and losses of an eye within 24 hours. Partial exemption removes routine logging, not severe-event reporting.

OSHA 510 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

General Duty Clause
OSHA Act Section 5(a)(1); requires employers to provide a workplace free of recognized hazards causing or likely to cause death or serious physical harm when no specific standard applies.
Construction standard applicability
29 CFR 1926 applies to construction, alteration, and repair including painting and decorating; where a 1926 standard is absent, applicable 1910 standards apply under 1926.20(a)(1).
Competent person definition
One who is capable of identifying existing and predictable hazards in the surroundings or working conditions and who has authorization to take prompt corrective measures to eliminate them.
Emergency action plan threshold
1926.35 requires a written emergency action plan for job sites with more than 10 employees; sites with 10 or fewer may communicate the plan orally to all employees.
Noise exposure limit
1926.52 Table D-1 permits 90 dBA for 8 hours, with a 5 dBA increase halving allowable duration: 95 dBA for 4 hours, 100 dBA for 2 hours, and 105 dBA for 1 hour.
PPE employer obligations
1926.95 requires employers to provide, use, and maintain PPE at no cost to employees, ensuring it is in sanitary and reliable condition and fits the hazard.
Fire extinguisher travel distance
1926.150(c)(1) requires at least one 2A-rated extinguisher per 3,000 square feet of protected building area, with travel distance not exceeding 100 feet.
Respiratory protection program
1926.103 adopts 1910.134, requiring a written program, medical evaluation, fit testing, training, and respirator maintenance when respirators are required.
Danger sign signal word
Under 1926.200, DANGER indicates an immediate hazard likely to cause death or serious injury and is used only where the hazard is immediate.
Materials stacking requirements
1926.250(b)(8) requires materials stored in tiers to be stacked, blocked, interlocked, and limited in height so they are stable and secure against sliding or collapse.
Rigging sling inspection
1926.251 requires rigging equipment and slings to be inspected before each use, removed from service when defective, and marked with rated capacity.
Powder-actuated tool operator
1926.302(e) requires powder-actuated tools to be used only by trained and certified employees, with eye protection and loading only after the tool is pointed.
Welding fire prevention
1926.352 requires removal of combustible materials from the welding area or use of guards and shields to prevent ignition of nearby combustibles.
Electrical lockout requirement
1926.417 requires circuits to be de-energized and locked out or tagged before work begins, with tags removed only by the person who applied them.
Scaffold load capacity
1926.451(a)(1) requires each scaffold and component to support its own weight and at least four times the maximum intended load without failure.
Scaffold fall protection threshold
1926.451(g) requires guardrail systems or personal fall arrest for employees on scaffold platforms more than 10 feet above a lower level.
Scaffold access prohibition
1926.451(e) requires safe access by ladder, stair tower, or ramp and prohibits employees from climbing cross braces to access scaffold platforms.
Fall protection trigger height
1926.501(b)(1) requires fall protection for employees on walking or working surfaces with an unprotected side or edge 6 feet or more above a lower level.
Personal fall arrest limits
1926.502(d) requires personal fall arrest systems to limit maximum arresting force to 1,800 pounds and arrest a fall within 3.5 feet.
Guardrail height requirement
1926.502(b) requires top rails at 42 inches plus or minus 3 inches and midrails at approximately 21 inches, each capable of withstanding 200 pounds.
Crane operator certification
1926.1427 requires crane operators to be qualified or certified by an accredited organization, with evaluation and documentation of operator competency.
Reverse signal alarm
1926.602(a)(9) requires earthmoving equipment operated in reverse to have an audible alarm, or a signal system, to warn employees in the area.
Trench egress requirement
1926.651(c)(2) requires a stairway, ladder, ramp, or other safe means of egress in trench excavations 4 feet or more deep, within 25 feet of lateral travel.
Excavation protective system threshold
1926.652(a)(1) requires protective systems such as sloping, shoring, or shielding for excavations 5 feet or more deep, unless entirely in stable rock.
Spoil pile setback
1926.651(i) requires excavated materials and equipment to be kept at least 2 feet from the edge of the excavation to prevent falls and collapse.
Steel erection fall protection
1926.760 requires fall protection for employees engaged in steel erection at 15 feet or more above a lower level, with specified exceptions and connectors.
Demolition engineering survey
1926.850 requires a competent person to conduct an engineering survey of the structure before demolition begins to determine structural condition and collapse risk.
Ladder training requirement
1926.1060 requires training for employees using ladders and stairways, covering hazards, proper use, and maximum load capacity, with retraining as needed.
Silica permissible exposure limit
1926.1152 sets a PEL of 50 micrograms per cubic meter of respirable crystalline silica as an 8-hour TWA, with an action level of 25 micrograms per cubic meter.
Hazard communication requirements
1926.59 adopts 1910.1200, requiring chemical inventory, labels, safety data sheets, and training for employees exposed to hazardous chemicals on site.
Fatality reporting timeframe
1904.39 requires employers to report work-related fatalities to OSHA within 8 hours and in-patient hospitalizations, amputations, or eye loss within 24 hours.
Recordable injury criteria
1904.7 defines a recordable case as one causing death, days away, restricted work, medical treatment beyond first aid, loss of consciousness, or significant diagnosis.

OSHA 510 study guide

OSHA Act: Employer Duties, Inspections, and Enforcement

What the Act requires

The OSH Act of 1970 gives OSHA authority to set and enforce workplace standards. Section 5(a)(1), the General Duty Clause, requires each employer to furnish a workplace free from recognized hazards likely to cause death or serious physical harm. Section 5(a)(2) requires compliance with specific OSHA standards, and Section 5(b) requires employees to follow rules and orders. The Act covers private-sector employers; state-plan states must be at least as effective as federal OSHA.

Enforcement basics

OSHA inspection priorities are imminent danger, fatality/catastrophe, valid employee complaint or referral, programmed inspections, and follow-up. Citations are classified as willful, serious, repeat, other-than-serious, or failure to abate. An employer may contest a citation, penalty, or abatement date within 15 working days; employees may contest the abatement period.

Worked example

An inspector finds an unguarded floor hole beside a walkway. A specific standard, 1926.501(b)(4), addresses holes, so the citation should rest on Section 5(a)(2) and that standard-not the General Duty Clause. If no specific standard covered the hazard, 5(a)(1) could apply if the hazard was recognized and likely to cause death or serious harm.

Traps

Do not use the General Duty Clause when a specific standard applies. “Recognized” can mean industry recognition, not only the employer’s actual knowledge. The contest deadline is 15 working days, not 30 days. Employee misconduct is not an automatic defense; the employer must show an effective program.

Choosing the Right Standard: 1910 vs. 1926

Which part applies

Part 1926 governs construction work: construction, alteration, repair, painting, decorating, and demolition. Part 1910 governs general industry, such as manufacturing, warehousing, and service operations. The same company can do both: a maintenance crew using 1910 standards inside an operating plant must follow 1926 when it performs construction work, such as modifying a wall or installing a new process line that is construction rather than routine maintenance.

Overlap and multi-employer sites

Construction-specific standards control where they address the hazard. Subpart C, 1926.20 through 1926.35, provides baseline duties: programs, frequent and regular inspections by a competent person, training, first aid, housekeeping, illumination, PPE, egress, and emergency action plans. On multi-employer sites, OSHA may cite the creating employer, the exposing employer, the correcting employer, and the controlling employer under the multi-employer citation policy.

Worked example

A contractor is replacing the roof membrane on a commercial building. Because this is alteration/repair of a structure, 1926 applies, including Subpart M fall protection at 6 feet. If the building owner’s own maintenance employee later unclogs a roof drain using a ladder, that routine maintenance task is generally general industry and 1910 applies.

Traps

Do not assume that a “general industry” site means 1910 for every task; construction contractors still follow 1926. Do not cite both 1910 and 1926 for the same hazard without analyzing which part governs. The controlling employer’s duty is to exercise reasonable care, not to supervise every subcontractor task.

Subpart C: General Safety and Health Provisions

Baseline employer duties

Subpart C, 1926.20–1926.35, sets minimum construction safety and health duties. Under 1926.20(a), an employer may not require employees to work in unsafe or unhealthful conditions. Under 1926.20(b)(1), the employer must initiate and maintain programs needed to comply with Part 1926; under (b)(2), a competent person must make frequent and regular inspections of job sites, materials, and equipment. Unsafe machinery must be removed or guarded under 1926.20(b)(3).

Competent and qualified persons

1926.32(f) defines a competent person as one who can identify existing and predictable hazards and has authority to take prompt corrective measures. 1926.32(m) defines a qualified person by degree, certificate, professional standing, or knowledge. 1926.21(b)(2) requires training in hazard recognition and prevention for employees exposed to hazards.

Worked example

A trench inspection is assigned to a supervisor who has completed trenching training but must call the home office before stopping work. The supervisor is not a competent person for Subpart P because the definition requires authority to take prompt corrective action. The employer must either give that authority or assign someone who has it.

Traps

“Competent” is not a personality trait or a synonym for “experienced.” Training without authority fails the definition. “Frequent and regular” inspections are not necessarily daily, but they must fit the hazard and work pace. Subpart C does not replace specific requirements such as 1926.651 daily excavation inspections.

Subparts D–F: Health Controls, PPE, and Fire Protection

Subpart D: health and environmental controls

Subpart D requires medical services and first aid (1926.50), sanitation and potable water (1926.51), noise controls (1926.52), air contaminant limits (1926.55), illumination (1926.56), and ventilation (1926.57). Hazard communication for construction is 1926.59, which enforces 1910.1200: labels, safety data sheets, and training.

Subpart E: PPE

1926.95 requires PPE appropriate to the hazard, employer-provided at no cost, maintained, and used. Subpart E addresses head protection (1926.100), hearing protection (1926.101), eye and face protection (1926.102), respiratory protection (1926.103, which incorporates 1910.134), and work over or near water (1926.106).

Subpart F: fire protection

1926.150 requires firefighting equipment and access; 1926.151 covers fire prevention and ignition sources; 1926.152 regulates flammable liquids; 1926.153 covers LP gas; 1926.154 covers temporary heating devices. Fire extinguishers must be suitable, accessible, and inspected.

Worked example

A worker uses a portable grinder. The hazard assessment calls for eye protection with side shields plus a face shield for grinding. The employer must provide both at no cost, train the worker in their use, and verify the face shield is in good condition. A dust mask alone would not satisfy eye/face protection.

Traps

PPE is not optional and generally cannot be charged to employees. A respirator requires a full 1910.134 program-medical evaluation, fit testing, training-not just issuing a mask. Flammable liquids have storage limits and bonding/grounding rules; a fire extinguisher does not replace ignition-source control.

Subparts G–H: Signs, Signals, Barricades, and Material Handling

Subpart G: signs, signals, barricades

1926.200 requires accident prevention signs and tags where hazards exist. Standard colors: red for danger, yellow for caution, and green for exit/safety instruction. 1926.201 covers signaling, including flaggers and hand signals. 1926.202 covers barricades for traffic control and protection. Signs do not replace physical guards; they warn about hazards that remain.

Subpart H: materials handling and storage

1926.250 requires stable storage, clear aisles and exits, and protection against sliding or collapse. Stored materials must not obstruct exits or electrical equipment. Employees may not be under suspended loads. 1926.251 requires rigging equipment-slings, shackles, hooks-to be inspected, marked with capacity, and used within rated loads. 1926.252 requires prompt disposal of waste and debris.

Worked example

A crew stacks 20-foot steel pipe on a job site. The pipes must be blocked or interlocked to prevent rolling, the stack must not block an exit, and no worker may stand downhill of the stack while it is being moved. Slings used to lift the pipe must be inspected before use and have a legible capacity tag.

Traps

Barricades and signs are not interchangeable: barricades provide a physical or traffic barrier; signs warn. Rigging inspections are not annual only; damaged slings must be removed from service immediately. “No employees under loads” applies to cranes and hoists, not just to overhead work.

Subparts I–K: Tools, Welding, and Electrical

Subpart I: tools

1926.300 requires tools to be guarded and in safe condition. Hand tools must be maintained (1926.301); power tools need proper switches and guards (1926.302); abrasive wheel guards, work rests, and tongue guards are specified in 1926.303. Jacks must be rated and stable (1926.305).

Subpart J: welding and cutting

1926.350 covers gas cylinders: secure them upright, keep caps on when not in use, and keep fuel gas and oxygen separated. 1926.351 covers arc welding; 1926.352 requires fire prevention, including removing combustibles and using a fire watch where needed. 1926.353 requires ventilation and protection from fumes; 1926.354 covers confined spaces.

Subpart K: electrical

1926.400–1926.449 cover wiring, grounding, temporary power, and lockout/tagout. Temporary receptacles must have GFCI protection or an assured equipment grounding conductor program (1926.404(b)(1)). 1926.416 requires protection from electrical hazards; 1926.417 requires lockout/tagout of circuits and equipment. Maintain 10 feet of clearance from unguarded power lines up to 50 kV, with greater distance at higher voltage.

Worked example

A crew sets up a temporary 120-volt receptacle for a circular saw. The receptacle lacks GFCI protection, so the employer must either install a GFCI or use an assured equipment grounding conductor program with recorded inspections and tests. A damaged extension cord must be removed from service.

Traps

A GFCI is not the only compliant option for temporary power-the assured grounding program is an alternative. Welding fire watches are required when combustibles cannot be removed and can be ignited. Lockout/tagout is not just a tag; energy must be isolated and verified.

Subpart L: Scaffolds

Scaffold basics

Subpart L, 1926.450–1926.454, covers scaffolds. Each scaffold and scaffold component must support its own weight plus at least four times the intended load (1926.451(a)(1)). Platforms must be fully planked, at least 18 inches wide, and guarded. Scaffolds must be braced, tied, or otherwise stabilized; base plates and mud sills are required where necessary.

Fall protection and access

Fall protection is required when a scaffold platform is 10 feet or more above a lower level (1926.451(g)(1)). Guardrails must have a top rail 38–45 inches high, a midrail, and toe boards where required. A competent person must inspect the scaffold before use and after changes. Access must be by ladder, ramp, or equivalent-not by climbing the frame.

Worked example

A two-point suspended scaffold is 40 feet high. Workers need guardrails and personal fall arrest; the scaffold must be tied to the building, and the competent person must inspect it before each shift and after any alteration. If a guardrail is removed for material handling, workers must use fall arrest.

Traps

The scaffold fall-protection trigger is 10 feet, not the general 6 feet. A top rail is 38–45 inches, not exactly 42 inches. “Fully planked” means no gaps that allow tools or feet to fall through. Never use a scaffold as a storage rack or as an anchorage unless designed for it.

Subpart M: Fall Protection

Trigger heights and systems

Subpart M, 1926.500–1926.503, requires fall protection for construction workers exposed to falls of 6 feet or more to a lower level, with specific exceptions. Holes, leading edges, wall openings, formwork, and excavation edges all require protection. Systems include guardrail systems, personal fall arrest, positioning devices, warning lines, safety nets, and covers.

System criteria

Guardrails are generally 42 inches high, plus or minus 3 inches, with a midrail and toe board. Personal fall arrest requires a full-body harness, a lanyard or lifeline, and an anchorage capable of supporting 5,000 pounds per employee or designed with a safety factor of at least two. Free fall must be limited to 6 feet or the system must limit arrest forces.

Worked example

A worker installs roof sheathing at an 8-foot elevation. Because the fall distance exceeds 6 feet, the employer must provide guardrails, personal fall arrest, or another compliant system. If the worker uses a personal fall arrest system, the anchor must be rated for 5,000 pounds, the harness must fit, and a rescue plan must exist.

Traps

The general construction trigger is 6 feet; scaffolds use 10 feet and steel erection uses 15 feet. A warning line is not fall protection by itself. Anchors are not automatically 5,000 pounds; verify the rating. A fall protection plan for leading-edge work is not a waiver from all fall protection.

Subparts N–O: Cranes, Hoists, and Motor Vehicles

Cranes and hoists

Subpart N covers cranes, derricks, hoists, elevators, and conveyors. 1926.550 requires frequent and periodic crane inspections, load charts, qualified operators, and signal persons. Loads must not exceed rated capacity, and outriggers must be fully extended and supported. For power lines, maintain at least 10 feet of clearance up to 50 kV and greater clearance above that.

Motor vehicles and equipment

Subpart O covers motor vehicles, mechanized equipment, and marine operations. 1926.601 requires seat belts, horns, brakes, and safe operating conditions for motor vehicles. 1926.602 covers earthmoving equipment, including ROPS, backing alarms, and no riders unless seated. Equipment must be inspected and maintained; parking on grades requires blocking or setting brakes.

Worked example

A crane will lift a steel beam near a 12.5 kV distribution line. The required minimum clearance is 10 feet, so the operator must maintain that distance or have the line de-energized and grounded by the utility. A spotter and a clearly understood signal system are required, and the load chart must be checked for boom length and radius.

Traps

Six feet is not the crane power-line clearance; 10 feet applies at lower voltages. A load chart is not a suggestion-capacity changes with radius. Backup alarms do not replace a spotter. Riders on earthmoving equipment must have a designated seat and seat belt.

Subpart P: Excavations

Excavation requirements

Subpart P, 1926.650–1926.652, requires a competent person to inspect excavations daily and after rain or other changes. Utilities must be located before digging. Protective systems-sloping, benching, shoring, or shielding-are required for excavations 5 feet or deeper unless the competent person determines there is no hazard, and for shallower excavations with hazards. Trenches 4 feet or deeper need a means of egress within 25 feet of lateral travel.

Soil and spoil

Soil must be classified as Type A, B, or C. Type C soil is the least stable and requires a 1.5H:1V slope if sloping is used; Type B is 1H:1V; Type A is 0.75H:1V. Spoil piles and equipment must be kept at least 2 feet from the edge. Water accumulation must be controlled, and hazardous atmospheres must be tested where oxygen deficiency or toxic gas may exist.

Worked example

A 6-foot trench is dug in Type C soil. The competent person cannot classify it as stable; a protective system is required. If the crew slopes, the slope must be at least 1.5 horizontal to 1 vertical. If there is no room to slope, a trench shield or shoring system must be used, and the crew needs a ladder within 25 feet.

Traps

The protective-system trigger is 5 feet, not 4 feet. The 2-foot spoil-pile rule is measured from the edge, not the bottom. A ladder is required at 4 feet, not 5 feet. A competent person cannot waive the requirement for a protective system without a documented determination.

Subparts Q–X: Concrete, Steel, Demolition, Power, Ladders

Concrete, steel, and underground

Subpart Q covers concrete and masonry: formwork must be designed and braced; 1926.701(b) requires impalement protection for reinforcing steel. Subpart R covers steel erection; 1926.760 requires fall protection at 15 feet, with controlled decking zones and fall protection for connectors. Subpart S covers underground construction: competent-person inspections, air monitoring, and emergency procedures.

Demolition, blasting, and power

Subpart T requires an engineering survey before demolition, utility shutoff, and controlled access. Subpart U requires qualified blasters, warning signals, and blast-area security. Subpart V covers power transmission and distribution: de-energize and ground, use minimum approach distances, and protect against induced voltage. Subpart W covers ROPS for certain equipment; Subpart X covers stairways and ladders.

Worked example

A steel-erection crew is connecting beams at 18 feet. General Subpart M would trigger at 6 feet, but steel erection under Subpart R allows fall protection at 15 feet for certain activities. At 18 feet, the crew must use guardrails, safety nets, personal fall arrest, or a controlled decking zone where permitted. The employer must also provide a rescue plan.

Traps

Do not apply the 6-foot trigger to steel erection without checking Subpart R. A demolition survey is not optional, and utilities must be shut off or protected. Ladders use a 4:1 setup ratio and must extend 3 feet above the landing. Stairways with four or more risers need handrails.

Subpart Z: Hazard Communication and Silica

Hazard communication

1926.59 applies 1910.1200 to construction. Employers must maintain a written HazCom program, ensure containers are labeled, obtain and make safety data sheets available, and train employees before exposure. Labels use pictograms, signal words, and hazard statements. Training must cover hazards, protective measures, and detection methods.

Silica

1926.1153 sets a permissible exposure limit of 50 micrograms per cubic meter as an 8-hour time-weighted average and an action level of 25. Table 1 lists common construction tasks with required engineering controls, work practices, and respiratory protection. If the employer fully implements Table 1, exposure monitoring is not required for that task. Otherwise, the employer must assess exposures and use controls to meet the PEL.

Worked example

A worker uses a handheld concrete saw to cut block. Table 1 requires an integrated water-delivery system and, depending on the task and duration, respiratory protection. The employer must also provide silica training, housekeeping to avoid dry sweeping, and medical surveillance if required. A disposable dust mask is not automatically adequate; the Table 1 respirator requirement controls.

Traps

Table 1 is not optional if the employer relies on it. Water controls must be used correctly; a trickle is not enough. HazCom training must occur before exposure, not after. Silica is not only a “dust” issue; it can cause silicosis and cancer.

Safety and Health Program Concepts

Program elements

A safety and health program is a systematic approach to preventing injuries. OSHA’s Recommended Practices identify management leadership, worker participation, hazard identification and assessment, hazard prevention and control, and education and training. 1926.20(b)(1) also requires construction employers to initiate and maintain programs necessary to comply with Part 1926.

How programs work

Management leadership means visible commitment, assigned responsibilities, and resources. Worker participation means employees help identify hazards and shape solutions. Hazard identification uses inspections, job hazard analyses, incident investigations, and employee reports. Hazard control follows the hierarchy of controls. Training must be understandable and matched to the work.

Worked example

A contractor has repeated near misses involving material handling. The program team reviews the incidents, finds that workers are lifting heavy forms manually, and applies the hierarchy: eliminate the lift with a conveyor, substitute lighter forms, use a lift assist, rotate workers, and require gloves. The team tracks corrective actions and checks whether injuries decline.

Traps

A written manual is not a program. A program without worker participation misses hazards. Training alone does not correct an engineering hazard. Do not treat PPE as the first control; it is the last line of defense.

Hazard Identification and Control

Identification and evaluation

Hazard identification finds unsafe conditions and practices before they cause harm. Tools include worksite inspections, job hazard analysis, incident and near-miss investigations, employee reports, and exposure monitoring. Evaluation considers severity and likelihood-how bad the outcome could be and how often exposure occurs.

Control

Use the hierarchy of controls: elimination, substitution, engineering controls, administrative controls, and PPE. Elimination removes the hazard; substitution replaces it with something safer; engineering controls isolate people from the hazard; administrative controls change how work is done; PPE protects the individual. PPE is least reliable because it depends on fit, use, and maintenance.

Worked example

A crew is exposed to silica dust while grinding. Elimination might use pre-cut materials; substitution could use a wet saw; engineering controls include water delivery and local exhaust; administrative controls include limiting duration and housekeeping; PPE includes a respirator. The employer should use the highest feasible control, not jump to respirators.

Traps

A hazard is not the same as risk. A near miss is a free lesson-investigate it. Administrative controls such as rotation do not reduce exposure if the total dose is unchanged. PPE does not eliminate the hazard.

Recordkeeping and Injury Reporting

Recordkeeping

29 CFR 1904 requires covered employers to record work-related fatalities, injuries, and illnesses that meet recording criteria. Forms include the OSHA 300 Log, 300A Annual Summary, and 301 Incident Report. Recordable cases include death, days away from work, restricted work or transfer, medical treatment beyond first aid, loss of consciousness, and significant injury or illness diagnosed by a physician.

Reporting to OSHA

Employers must report a work-related fatality within 8 hours. They must report an in-patient hospitalization, amputation, or loss of an eye within 24 hours. Reporting is not the same as recording; a case can be recordable without being reportable. Electronic submission requirements apply to certain establishments.

Worked example

A worker cuts a hand and receives stitches. Stitches are medical treatment beyond first aid, so the case is recordable on the 300 Log within seven calendar days. It is not a fatality, in-patient hospitalization, amputation, or loss of an eye, so no 8-hour or 24-hour report is required. If the worker is admitted to the hospital for treatment, the 24-hour reporting rule applies.

Traps

First aid is not recordable. The fatality report is 8 hours; hospitalization, amputation, and loss of eye are 24 hours. Hospitalization for observation only is generally not reportable. Recording does not automatically mean the employer is at fault.

OSHA 510 cheat sheet

Quick reference

OSHA Act, General Industry vs. Construction, and 1926 Subpart C

  • OSHA Act Section 5(a)(1), the General Duty Clause, requires employers to furnish a workplace free of recognized hazards likely to cause death or serious physical harm when no specific standard applies.

  • Section 5(a)(2) obligates employers to comply with specific OSHA standards; Section 5(b) binds employees to comply with rules and orders applicable to their own conduct.

  • 29 CFR 1926 governs construction, defined in 1910.12(b) as work for construction, alteration, and/or repair, including painting and decorating; 29 CFR 1910 covers general industry.

  • Where a construction activity is not addressed by a 1926 standard, 1926.20(a)(1) requires compliance with applicable 1910 standards; Subpart C is the fallback gateway.

  • 1926.20(b)(1)-(2) require a safety and health program and frequent, regular job site inspections by a competent person designated by the employer.

  • 1926.21(b)(2) requires training for employees exposed to unsafe conditions, with recognition of hazards and avoidance procedures; 1926.21(b)(1) covers first aid and medical services.

  • 1926.33 adopts 1910.1020 access to employee exposure and medical records; 1926.34 requires exit routes kept unobstructed and marked.

  • 1926.35 requires a written emergency action plan for sites with more than 10 employees, and an oral plan communicated to all employees for 10 or fewer.

  • 1926.23 and 1926.24 cover first aid supplies and fire protection/PPE obligations respectively, coordinating Subpart C with Subparts E and F.

Quick reference

29 CFR 1926 Subparts D-F: Occupational Health, PPE, Fire Protection

  • 1926.52 Table D-1 permissible noise exposures: 90 dBA for 8 hours, 95 dBA for 4, 100 dBA for 2, 105 dBA for 1, 110 dBA for 0.5, 115 dBA for 0.25 hour; a 5 dBA increase halves allowable duration.

  • 1926.55 adopts ACGIH TLVs as advisory limits for air contaminants; 1926.57 covers ventilation for abrasive blasting and spray operations.

  • 1926.59 adopts 1910.1200 Hazard Communication; 1926.62 lead and 1926.1126 chromium (VI) set action levels and exposure limits for construction.

  • 1926.95 requires PPE provided, used, and maintained in sanitary, reliable condition at no cost to employees; 1926.96 covers occupational foot protection.

  • 1926.100 head protection required where falling objects or electrical hazards exist; 1926.101 hearing protection required at exposure above limits in 1926.52.

  • 1926.102 eye and face protection must comply with ANSI Z87.1 and be provided when machines or operations present eye or face injury hazards.

  • 1926.103 respiratory protection adopts 1910.134, requiring a written program, medical evaluation, fit testing, and training.

  • 1926.150 fire protection requires a firefighting program; 1926.152 governs flammable liquids storage; 1926.151 addresses ignition hazards.

  • 1926.150(c)(1) requires at least one 2A-rated extinguisher per 3,000 square feet of protected building area, with travel distance not exceeding 100 feet.

Quick reference

29 CFR 1926 Subparts G-H: Signs, Signals, Barricades; Materials Handling

  • 1926.200(a) requires accident prevention signs where hazards exist, with signal words DANGER (immediate danger), WARNING (potential hazard), CAUTION (minor hazard), and NOTICE (non-hazard information).

  • 1926.201 signaling by flaggers uses red flags at least 24 inches square; 1926.202 barricades must conform to the Manual on Uniform Traffic Control Devices.

  • 1926.200(g) requires traffic control signs to conform to MUTCD; 1926.203 defines standard accident prevention signs and tags.

  • 1926.250(a) requires materials stored so that they are stable and secure against sliding or collapse, with clearance maintained for aisles and passageways.

  • 1926.250(b)(2) limits stacks of bagged materials to a height that maintains stability; 1926.250(b)(5) requires stacked materials to be kept clear of walls.

  • 1926.250(b)(8) requires materials stored in tiers to be stacked, blocked, interlocked, and limited in height to prevent sliding or collapse.

  • 1926.251 governs rigging equipment: slings inspected before use, removed from service if defective, and marked with rated capacity.

  • 1926.252 requires disposal of waste materials by removal from the site at frequent intervals; 1926.252(e) covers waste handling in multi-story structures.

  • 1926.252(c) requires enclosed chutes for dropping material more than 20 feet, with an opening not exceeding 45 degrees from horizontal.

Quick reference

29 CFR 1926 Subparts I-K: Hand and Power Tools, Welding, Electrical

  • 1926.300(a) requires tools to be maintained in safe condition; 1926.300(b)(1) requires guards on moving parts of power tools that expose employees to injury.

  • 1926.301 requires hand tools to be inspected before use and removed from service if defective; 1926.302 covers power-operated hand tools, including electric and powder-actuated tools.

  • 1926.302(e) requires powder-actuated tools to be operated only by trained, certified employees, with eye protection and loading after the tool is pointed.

  • 1926.303 requires abrasive wheels to be inspected and ring-tested before mounting; 1926.304 covers woodworking tools and 1926.305 jacks.

  • 1926.350 covers gas welding and cutting; 1926.350(a)(10) requires cylinders kept upright and secured; 1926.350(b) covers oxygen-fuel gas storage and separation.

  • 1926.351 covers arc welding and cutting; 1926.352 governs fire prevention, requiring removal of combustibles or use of guards and shields.

  • 1926.353 requires ventilation for welding in confined spaces; 1926.354 covers welding, cutting, and heating in way of preservative coatings.

  • 1926.400-1926.408 cover electrical: 1926.403 requires approved electrical conductors and equipment; 1926.404 covers wiring design and protection.

  • 1926.405 governs wiring methods, components, and equipment; 1926.406 covers specific-purpose equipment; 1926.407 covers hazardous locations.

  • 1926.416(a) requires protection of employees from electrical hazards, including de-energizing and lockout; 1926.417 covers lockout and tagging of circuits.

Quick reference

29 CFR 1926 Subpart L: Scaffolds

  • 1926.451(a)(1) requires each scaffold and scaffold component to support its own weight and at least 4 times the maximum intended load without failure.

  • 1926.451(a)(4) requires access to scaffold platforms; 1926.451(e) requires ladders, stair towers, or ramps, and prohibits climbing cross braces.

  • 1926.451(b)(1) requires platform units to be fully planked or decked between the front uprights and guardrail supports, with limited exceptions.

  • 1926.451(b)(3) limits gaps between platforms and uprights to 1 inch; 1926.451(b)(4) requires platforms to be overlapped or secured against movement.

  • 1926.451(c) requires scaffolds to be braced, guyed, or tied to prevent tipping; 1926.451(d) covers suspension scaffold support devices.

  • 1926.451(f) covers use: scaffolds must not be loaded beyond rated capacity, and employees must not work on scaffolds during storms or high winds.

  • 1926.451(g) requires guardrail systems or personal fall arrest for employees on platforms more than 10 feet above a lower level.

  • 1926.452 covers specific scaffold types, including mobile, tube and coupler, and suspension scaffolds; 1926.453 covers aerial lifts.

  • 1926.454 requires training for employees who perform work on scaffolds, covering hazards, load capacities, and fall protection, with retraining when necessary.

Quick reference

29 CFR 1926 Subpart M: Fall Protection

  • 1926.501(b)(1) requires fall protection for employees on walking/working surfaces with an unprotected side or edge 6 feet or more above a lower level.

  • 1926.501(b)(4) requires protection from falling through holes, including covers secured and marked; 1926.502(i) covers hole covers.

  • 1926.501(b)(13) requires residential construction fall protection at 6 feet, or a written fall protection plan under 1926.502(k) for specified activities.

  • 1926.502(b) requires guardrail systems with top rail at 42 inches plus or minus 3 inches and midrail at approximately 21 inches, capable of 200 pounds.

  • 1926.502(d) requires personal fall arrest systems to limit maximum arresting force to 1,800 pounds and arrest a fall within 3.5 feet.

  • 1926.502(d)(16) requires prompt rescue of employees in the event of a fall or assurance of self-rescue; 1926.502(d)(19) requires anchorage at 5,000 pounds or twice the expected load.

  • 1926.502(f) covers warning line systems at 6 feet or more from the edge, with lines 34 to 39 inches high and 500-pound strength.

  • 1926.502(h) covers safety monitoring systems, requiring a competent person to monitor and warn employees, with no other duties assigned.

  • 1926.503 requires fall protection training, with retraining when there is reason to believe the employee lacks understanding or skill.

Quick reference

29 CFR 1926 Subparts N-O: Cranes, Derricks, Hoists; Motor Vehicles and Equipment

  • 1926.1400 scope covers power-operated equipment used to hoist, lower, and horizontally move a suspended load, with exclusions listed in 1926.1400(c).

  • 1926.1417 requires equipment to be operated only by a qualified operator and in accordance with the manufacturer's procedures and load charts.

  • 1926.1419 covers signals; 1926.1420 covers signal person qualifications; 1926.1421 covers voice signals.

  • 1926.1423 covers fall protection for crane personnel; 1926.1424 covers work area control; 1926.1425 covers keeping clear of the load.

  • 1926.1427 requires operator qualification or certification, with evaluation and licensing requirements; 1926.1431 covers hoisting personnel.

  • 1926.1433 covers safety devices, including operational aids such as load moment indicators and anti-two-block devices.

  • 1926.1441 covers equipment with a rated hoisting/lifting capacity of 2,000 pounds or less.

  • 1926.600 covers motor vehicles and mechanized equipment: 1926.601 requires seat belts in vehicles; 1926.602 covers earthmoving equipment.

  • 1926.602(a)(9) requires audible alarms on earthmoving equipment when operated in reverse; 1926.604 covers site clearing; 1926.605 covers marine operations.

Quick reference

29 CFR 1926 Subpart P: Excavations

  • 1926.650 defines a competent person as one capable of identifying existing and predictable hazards and authorized to take prompt corrective measures.

  • 1926.651(b) requires underground installations to be located and protected before excavation; 1926.651(c) covers access and egress.

  • 1926.651(c)(2) requires a stairway, ladder, ramp, or other safe means of egress in trench excavations 4 feet or more deep, within 25 feet of lateral travel.

  • 1926.651(g) requires testing for oxygen deficiency and hazardous atmospheres in excavations 4 feet or more deep where a hazardous atmosphere could exist.

  • 1926.651(i) requires excavated materials and equipment kept at least 2 feet from the edge of the excavation.

  • 1926.652(a)(1) requires protective systems for excavations 5 feet or more deep, unless the excavation is entirely in stable rock.

  • 1926.652(b) permits sloping, benching, shoring, or shielding; 1926.652(c) requires protective system design by a registered professional engineer for certain conditions.

  • 1926.651(k) requires daily inspections by a competent person before work begins and as needed throughout the shift, and after rainstorms or other hazard-increasing events.

  • 1926.651(j) requires protection from loose rock or soil and removal of excavated material that could fall into the excavation.

Quick reference

29 CFR 1926 Subparts Q-X: Concrete, Steel, Underground, Demolition, Blasting, Power Transmission, ROPS, Ladders

  • 1926.701 covers concrete construction: 1926.701(b) prohibits construction loads on a concrete structure unless the employer determines the structure can support them.

  • 1926.702 covers equipment and tools; 1926.703 covers cast-in-place concrete, including formwork design by a qualified person.

  • 1926.750-1926.761 cover steel erection; 1926.754 covers structural steel assembly; 1926.760 requires fall protection at 15 feet for steel erection.

  • 1926.751 requires a site-specific erection plan for certain steel erection activities; 1926.752 covers site layout and construction sequence.

  • 1926.800 covers underground construction, including air quality, communication, and check-in/check-out procedures for employees underground.

  • 1926.850-1926.859 cover demolition: 1926.850 requires an engineering survey by a competent person before demolition begins.

  • 1926.851 covers stairs, passageways, and ladders; 1926.852 covers chutes; 1926.853 covers removal of materials through floor openings.

  • 1926.900-1926.914 cover blasting: 1926.900 requires blasting conducted by qualified persons and warning signals; 1926.909 covers firing precautions.

  • 1926.950-1926.960 cover power transmission and distribution; 1926.960(c) requires minimum approach distances to energized lines.

  • 1926.1000-1926.1003 cover rollover protective structures; 1926.1050-1926.1060 cover stairways and ladders, including 1926.1053 ladder requirements and 1926.1060 training.

Quick reference

29 CFR 1926 Subpart Z: Toxic and Hazardous Substances, HazCom, Silica

  • 1926.1101 covers asbestos, with permissible exposure limits and required work practices for construction activities; 1926.1103 covers 13 carcinogens.

  • 1926.1126 covers chromium (VI), with a permissible exposure limit of 5 micrograms per cubic meter as an 8-hour TWA.

  • 1926.1127 covers cadmium; 1926.1152 covers respirable crystalline silica in construction, with a PEL of 50 micrograms per cubic meter as an 8-hour TWA.

  • 1926.1153 requires engineering controls, including wet methods or dust collection, and specifies Table 1 tasks with required controls.

  • 1926.1153(g) requires a written exposure control plan, designated competent person, and employee training on silica hazards.

  • 1926.1153(i) requires medical surveillance for employees exposed at or above the action level of 25 micrograms per cubic meter for 30 or more days per year.

  • 1926.59 adopts 1910.1200 Hazard Communication, requiring labels, safety data sheets, and training for employees exposed to hazardous chemicals.

  • 1926.55 adopts ACGIH threshold limit values as advisory limits for air contaminants; 1926.60 covers methylenedianiline; 1926.61 covers 1,3-butadiene.

  • 1926.62 covers lead, with an action level of 30 micrograms per cubic meter as an 8-hour TWA and a PEL of 50 micrograms per cubic meter.

Quick reference

Safety and Health Program Concepts and Recordkeeping/Injury Reporting

  • A safety and health program typically includes management leadership, worker participation, hazard identification and assessment, hazard prevention and control, education and training, and program evaluation.

  • Hazard control follows the hierarchy of controls: elimination, substitution, engineering controls, administrative controls, and personal protective equipment.

  • 1926.20(b)(2) requires frequent and regular inspections of job sites, materials, and equipment by a competent person as part of the safety program.

  • 1926.21(b)(2) requires employee training on hazard recognition and avoidance procedures; 1926.35 requires emergency action plans.

  • 29 CFR 1904 requires recording of work-related fatalities, injuries, and illnesses; 1904.39 requires reporting fatalities within 8 hours and in-patient hospitalizations, amputations, or eye loss within 24 hours.

  • 1904.32 requires annual summary (OSHA Form 300A) posting from February 1 to April 30; 1904.29 covers forms 300, 301, and 300A.

  • 1904.7 defines a recordable case as one resulting in death, days away from work, restricted work or transfer, medical treatment beyond first aid, loss of consciousness, or significant injury/illness diagnosis.

  • 1904.5 covers work-relatedness, including the presumption that injuries in the work environment are work-related and exceptions for members of the public and personal tasks.

  • 1904.41 requires electronic submission of injury and illness information for establishments meeting size and industry criteria.

OSHA 510 key terms

General Duty Clause

Section 5(a)(1) of the OSH Act requires employers to furnish a workplace free from recognized hazards likely to cause death or serious physical harm, even when no specific standard covers the hazard.

Related: Recognized Hazard, OSHA Standards
Recognized Hazard

A condition that a reasonable person with knowledge of the industry would identify as dangerous, or that the employer already knows about through experience, injury records, or industry practice.

Related: General Duty Clause, Hazard Identification
Multi-Employer Worksite Doctrine

OSHA policy holding the creating, exposing, correcting, and controlling employers jointly responsible for hazards on a shared construction site, based on the role each played in causing or abating the hazard.

Related: Controlling Employer, Competent Person
Controlling Employer

The employer with general supervisory authority over a worksite, such as the general contractor, who is responsible for ensuring hazards are corrected even if its own employees are not exposed.

Related: Multi-Employer Worksite Doctrine, Competent Person
Competent Person

One who is capable of identifying existing and predictable hazards in surroundings and who has authorization to take prompt corrective measures to eliminate them, as required in many 1926 subparts.

Related: Qualified Person, Hazard Identification
Qualified Person

One who, by possession of a recognized degree, certificate, or professional standing, or by extensive knowledge, training, and experience, has successfully demonstrated ability to solve or resolve problems relating to the subject matter.

Related: Competent Person, Registered Professional Engineer
Construction Standard Applicability

29 CFR 1926 applies to construction, alteration, and repair work, including painting and decorating; maintenance work is generally covered by 29 CFR 1910 general industry rules instead.

Related: OSHA Standards, General Industry Standard
General Industry Standard

29 CFR 1910 rules covering manufacturing, warehousing, and most non-construction employment; some provisions apply to construction through cross-references in 1926 subparts.

Related: Construction Standard Applicability, OSHA Standards
OSHA Standards

Legally enforceable rules published in 29 CFR parts 1910, 1926, and related parts that specify required workplace conditions, methods, and training for covered employers.

Related: General Duty Clause, Construction Standard Applicability
Hazard Identification

The systematic process of finding workplace conditions and practices that could cause injury or illness, using inspections, job hazard analysis, injury records, and employee reports.

Related: Job Hazard Analysis, Hierarchy of Controls
Job Hazard Analysis

A technique that breaks a task into steps, identifies hazards at each step, and defines controls before work begins; often documented on a pre-task plan for high-risk construction activities.

Related: Hazard Identification, Hierarchy of Controls
Hierarchy of Controls

A ranked approach to reducing risk: eliminate the hazard, substitute a safer method, apply engineering controls, then administrative controls, with personal protective equipment as the last line of defense.

Related: Hazard Identification, Personal Protective Equipment
Site Safety and Health Program

An employer's organized set of policies, procedures, training, and accountability measures for managing workplace safety, typically covering management commitment, worker participation, hazard identification, and training.

Related: Hazard Identification, Competent Person
Exposure Control Plan

A written program required for bloodborne pathogens and other health hazards that describes exposure determinations, control methods, work practices, and post-exposure procedures for affected employees.

Related: Hazard Communication Program, Personal Protective Equipment
Hazard Communication Program

A written program under 1926.59 requiring safety data sheets, container labels, and employee training on hazardous chemicals in the workplace, aligned with the global harmonized system.

Related: Safety Data Sheet, Respirable Crystalline Silica
Safety Data Sheet

A standardized 16-section document supplied by the chemical manufacturer that describes hazards, safe handling, and emergency measures for a hazardous substance; must be readily accessible to workers.

Related: Hazard Communication Program, Permissible Exposure Limit
Respirable Crystalline Silica

Airborne particles of crystalline quartz small enough to reach the deep lung; 1926.1153 sets a permissible exposure limit and requires engineering controls, respiratory protection, and medical surveillance.

Related: Permissible Exposure Limit, Table 1 Silica Tasks
Table 1 Silica Tasks

A list of common construction tasks in 1926.1153 with specified engineering controls and work practices; employers who fully follow the assigned controls need not perform exposure monitoring.

Related: Respirable Crystalline Silica, Permissible Exposure Limit
Permissible Exposure Limit

The maximum airborne concentration of a substance to which a worker may be exposed, averaged over a stated time period, as established by OSHA standards.

Related: Respirable Crystalline Silica, Safety Data Sheet
Personal Protective Equipment

Equipment worn to minimize exposure to hazards, such as hard hats, gloves, and eye protection; employers must assess hazards, provide suitable gear at no cost, and train employees in its use.

Related: Hierarchy of Controls, Eye and Face Protection
Eye and Face Protection

Protective devices meeting 1926.102 requirements that must be worn when machines or operations present potential eye or face injury from flying particles, molten metal, chemicals, or light radiation.

Related: Personal Protective Equipment, Welding Protection
Fire Prevention Plan

A written plan under 1926.24 and 1926.150 addressing ignition sources, combustible storage, firefighting equipment, alarm procedures, and employee training for the site.

Related: Fire Extinguisher, Hot Work Permit
Hot Work Permit

A written authorization required before welding, cutting, or other spark-producing operations, documenting that fire hazards have been removed and a fire watch is in place.

Related: Fire Prevention Plan, Welding Protection
Welding Protection

Screens, helmets, and eye protection required around welding and cutting to shield the operator and nearby workers from arc flash, sparks, and hot slag.

Related: Eye and Face Protection, Hot Work Permit
Traffic Control Plan

A plan for signs, signals, barricades, and flaggers that routes vehicles and pedestrians safely through or around a construction work zone.

Related: Flaggers, Barricade
Flaggers

Trained workers who control traffic with signals and high-visibility gear; 1926.201 requires them to be competent in flagging procedures and positioned to be clearly visible.

Related: Traffic Control Plan, Barricade
Barricade

A physical barrier used to block access, protect the public from hazards, or channel traffic; must be visible and appropriate to the hazard and location.

Related: Traffic Control Plan, Fall Protection
Material Storage and Stacking

1926.250 requirements for keeping stored materials stable, stacked on level surfaces, blocked or interlocked to prevent sliding, and kept clear of walkways and exits.

Related: Rigging, Material Handling
Rigging

Slings, shackles, and hardware used to connect a load to a hoisting device; slings must be inspected, rated, and removed from service when damaged.

Related: Crane Operator Certification, Material Storage and Stacking
Ground-Fault Circuit Interrupter

A device that detects a ground fault and quickly interrupts power; required for 120-volt receptacles on construction sites and for temporary wiring in wet or damp locations.

Related: Assured Equipment Grounding Conductor Program, Lockout/Tagout
Assured Equipment Grounding Conductor Program

An alternative to GFCIs in which cord sets and equipment are visually inspected and electrically tested on a documented schedule to verify grounding continuity.

Related: Ground-Fault Circuit Interrupter, Lockout/Tagout
Lockout/Tagout

Procedures for isolating and de-energizing energy sources before servicing equipment, including applying locks and tags to prevent accidental startup or release of stored energy.

Related: Ground-Fault Circuit Interrupter, Hazard Identification
Scaffold Load Capacity

A scaffold must support its own weight plus at least four times the maximum intended load, with platforms fully planked and rated for the work performed.

Related: Scaffold Competent Person, Fall Protection
Scaffold Competent Person

The person who determines scaffold feasibility, supervises erection and dismantling, and inspects scaffolds before each work shift and after events that could affect structural integrity.

Related: Scaffold Load Capacity, Competent Person
Fall Protection

Systems such as guardrails, safety nets, and personal fall arrest used to protect workers from falls of six feet or more in construction, with specific trigger heights for some activities.

Related: Personal Fall Arrest System, Controlled Access Zone
Personal Fall Arrest System

A system of anchor, connector, and body harness that stops a fall; must limit arrest forces and keep the worker from striking a lower level.

Related: Fall Protection, Controlled Access Zone
Controlled Access Zone

A designated area near an unprotected edge where only trained workers may enter, marked by control lines, used for leading edge work and certain other fall-hazard tasks.

Related: Fall Protection, Personal Fall Arrest System
Crane Operator Certification

1926.1427 requires crane operators to be certified or licensed by an accredited organization and evaluated on the specific equipment type they operate.

Related: Rigging, Crane Swing Radius
Crane Swing Radius

The area swept by the rotating superstructure or counterweight; it must be barricaded to prevent employees from being struck by the crane.

Related: Crane Operator Certification, Barricade
Excavation Protective System

Shoring, shielding, or sloping required for trenches five feet or deeper, designed by a competent person based on soil classification and depth.

Related: Soil Classification, Excavation Competent Person
Soil Classification

Grouping of soil as stable rock, Type A, Type B, or Type C based on strength and stability, which determines the maximum allowable slope and protective system for an excavation.

Related: Excavation Protective System, Excavation Competent Person
Excavation Competent Person

The person who inspects excavations daily and after events like rain or vibration, classifies soil, and determines protective system requirements and access/egress needs.

Related: Soil Classification, Excavation Protective System
Stairway and Ladder Requirements

1926.1052 and 1926.1053 rules covering stair rails, landings, ladder angle, side rails, and the three-foot extension of ladders above a landing.

Related: Fall Protection, Competent Person
Recordkeeping and Injury Reporting

Employers must record serious injuries and illnesses on OSHA forms and report fatalities within eight hours and hospitalizations, amputations, or eye losses within twenty-four hours.

Related: OSHA Standards, Site Safety and Health Program
General Safety and Health Provisions

1926 Subpart C duties requiring employers to provide safe working conditions, train employees, designate competent persons, and maintain accident prevention responsibilities on construction sites.

Related: Competent Person, Site Safety and Health Program

OSHA 510 study plan

8 weeks · About 6 hours per week

Week 1

OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions) & Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting

  • Map the structure of 29 CFR 1926 by Subpart and state which Subparts fall inside each of the 11 exam domains

  • Distinguish employer duties under Section 5(a)(1) general duty clause from specific standard violations, and explain the multi-employer citation policy (controlling, exposing, correcting, creating employers)

  • Compare General Industry 29 CFR 1910 and Construction 29 CFR 1926 coverage triggers, and apply 1910.12(a) to decide which part governs a mixed operation

  • Walk through 1926 Subpart C requirements: safety and health program elements in 1926.20(b), competent person designations, and 1926.21 training obligations

  • Explain the 11(c) anti-retaliation framework, inspection and citation process, and the 8-hour fatality / 24-hour hospitalization reporting rule in 1904.39

Your checkpoint

One-page jurisdiction decision tree plus a 20-row Subpart-to-domain mapping table, self-quizzed to 90% accuracy

Week 2

29 CFR 1926 Subpart M: Fall Protection & 29 CFR 1926 Subpart L: Scaffolds

  • Apply 1926.501(b) duty-to-have-fall-protection triggers at 6 ft, 10 ft, 15 ft, and 50 ft for each walking-working surface type

  • Select and justify the conventional fall protection system (guardrail, safety net, personal fall arrest, positioning device, warning line, controlled access zone) permitted by each 1926.502 provision

  • Calculate total fall distance and required clearance for a personal fall arrest system, including lanyard length, deceleration distance, harness stretch, and a safety margin above the lower level

  • Identify the 1926.502(d) hardware and component criteria: anchorage strength, self-locking snap hooks, D-ring placement, and prompt rescue requirements

  • Classify scaffolds under 1926 Subpart L and state the capacity, planking, and access requirements for each type

  • State the 1926.451(g) fall protection threshold and the 1926.451(f) competent person inspection and tagging rules for scaffolds

Your checkpoint

Completed fall-distance worksheet for six scenarios plus a scaffold type comparison table, both scored against the standard text

Week 3

29 CFR 1926 Subpart P: Excavations & 29 CFR 1926 Subparts N–O: Cranes, Derricks, Hoists, Elevators and Conveyors; Motor Vehicles, Mechanized Equipment and Marine Operations

  • Classify soil by 1926 Subpart P Appendix A and select the correct protective system (sloping, benching, shoring, shield) for each soil type and depth

  • Determine when a protective system is required under 1926.652(a) and when the 5 ft shallow-excavation exemption applies

  • Apply the 1926.651 access/egress, spoil pile, surface encumbrance, water accumulation, and atmospheric testing rules

  • Describe the competent person's daily inspection duties and the 1926.651(c) and (k) requirements for support systems and hazardous atmospheres

  • State crane operator qualification and certification requirements under 1926.1427 and the 1926.1412 inspection tiers (shift, monthly, annual, post-assembly)

  • Explain 1926.1417 operation rules, power line safety under 1926.1408, and the signal person and rigger qualification requirements

Your checkpoint

Excavation protection decision matrix plus a 15-question self-test on crane and excavation requirements, with written corrections for every miss

Week 4

29 CFR 1926 Subparts I–K: Tools - Hand and Power; Welding and Cutting; Electrical & 29 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

  • Apply 1926 Subpart I guarding requirements: point of operation, nip points, rotating parts, and the 1926.300(b) requirements for portable circular saws and abrasive wheel guards

  • State the 1926.302 and 1926.304 rules for pneumatic and powder-actuated tools, including operator certification and loading procedures

  • Explain 1926 Subpart J welding requirements: fire watch triggers, hot work permits, ventilation, cylinder storage, and the 1926.353 confined space provisions

  • Apply 1926 Subpart K electrical rules: assured equipment grounding conductor program, GFCI requirements, temporary wiring, and lockout/tagout under 1926.417

  • Identify respirable crystalline silica triggers under 1926.1153 and select the correct Table 1 engineering control for common construction tasks

  • Explain the 1926.1153 exposure assessment, medical surveillance, and written exposure control plan obligations, and describe the Hazard Communication 1926.1200 written program and SDS access rules

Your checkpoint

Silica Table 1 task-to-control lookup sheet for ten common tasks plus a 25-question mixed practice set at 80% or better

Week 5

29 CFR 1926 Subparts D–F: Occupational Health and Environmental Controls, Personal Protective and Life Saving Equipment, Fire Protection and Prevention & 29 CFR 1926 Subparts G–H: Signs, Signals and Barricades; Materials Handling, Storage, Use and Disposal

  • Apply 1926 Subpart D occupational health rules: 1926.52 noise exposure limits, hearing conservation triggers, and 1926.55 air contaminant limits

  • State 1926 Subpart E PPE selection, training, and hazard assessment obligations under 1926.95 and 1926.102 eye/face protection criteria

  • Explain 1926 Subpart F fire protection requirements: fire extinguisher ratings and travel distance, 1926.150(c) portable extinguisher rules, and 1926.151 fire prevention plan elements

  • Apply 1926 Subpart G requirements for traffic control in work zones, flagger qualifications under 1926.201, and barricade/sign standards

  • State 1926 Subpart H material storage, stacking, and access rules, including 1926.250(b) stacking limits and 1926.252 disposal requirements

  • Explain rigging and material handling equipment inspection duties and the 1926.251 sling capacity and inspection criteria

Your checkpoint

Two-page compliance checklist covering PPE, fire extinguisher placement, and material storage, applied to a hypothetical site description

Week 6

29 CFR 1926 Subparts Q–X: Concrete and Masonry, Steel Erection, Underground Construction, Demolition, Blasting, Power Transmission, Rollover Protective Structures, and Stairways and Ladders & OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions)

  • Apply 1926 Subpart M stairway and 1926 Subpart X ladder requirements: 1926.1053 ladder use rules, 1926.1052 stairway requirements, and 1926.1060 training obligations

  • State 1926 Subpart Q concrete and masonry requirements for formwork, shoring, and the 1926.702 power concrete placement rules

  • Explain 1926 Subpart R steel erection requirements: controlled decking zone limits, 1926.760 fall protection triggers, and connector requirements

  • Describe 1926 Subpart S underground construction, Subpart T demolition, Subpart U blasting, Subpart V power transmission, and Subpart W rollover protective structure key requirements at a recognition level

  • Re-verify the Subpart C competent person and training obligations against the Subparts studied in weeks 2 through 6

Your checkpoint

Ladder and stairway inspection card set plus a full-length 60-question timed practice exam at 75% or better

Week 7

Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting & 29 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

  • Build a safety and health program outline using the seven core elements: management leadership, worker participation, hazard identification and assessment, hazard prevention and control, education and training, evaluation and improvement, and coordination with contractors

  • Apply the hierarchy of controls to five construction hazards and rank controls by effectiveness

  • Explain 29 CFR 1904 recordkeeping: recordability criteria, the partially exempt list, 300/300A/301 forms, and posting deadlines

  • State the 1904.39 reporting timelines and the 1904.35 employee involvement and anti-retaliation provisions

  • Revisit silica and HazCom requirements and connect them to the written program and training documentation you would audit on site

Your checkpoint

Draft site safety and health program outline with a completed sample OSHA 300 log entry set and a recordability decision log for ten cases

Week 8

OSHA Act, General Industry vs. Construction standards, and 29 CFR 1926 Subpart C (General Safety and Health Provisions) & Safety and Health Program concepts, hazard identification and control, and recordkeeping/injury reporting & 29 CFR 1926 Subpart M: Fall Protection & 29 CFR 1926 Subpart P: Excavations & 29 CFR 1926 Subpart Z: Toxic and Hazardous Substances, including Hazard Communication and Silica

  • Re-run all domain self-quizzes and log every missed item by domain to identify the three weakest areas

  • Re-study the weakest three areas using the standard text and rewrite the governing rule in your own words for each miss

  • Complete two full-length timed practice exams under exam conditions and compare scores to the week 6 baseline

  • Recite from memory the key numeric thresholds across all domains: fall heights, excavation depths, silica action level and PEL, noise limits, and reporting timelines

  • Assemble a one-page personal quick-reference sheet limited to numbers and decision triggers

Your checkpoint

Final practice exam score of 85% or better plus a completed one-page numeric quick-reference sheet and a written remediation log

Milestones

Week 2: Score 80% or better on a 20-question fall protection and scaffold self-quiz, and correctly calculate total fall distance and clearance for all six worksheet scenarios

Week 4: Score 80% or better on the 25-question mixed tools, welding, electrical, and silica set, and correctly match all ten silica tasks to their Table 1 control

Week 6: Score 75% or better on the 60-question timed practice exam, with no single domain below 60%

Week 8: Score 85% or better on the final full-length practice exam, with every domain at or above 75% and the numeric quick-reference sheet complete

OSHA 510 exam day

Your checklist

Government-issued photo ID

Bring the original, unexpired ID you used when registering (driver's license, passport, or state ID). Confirm with the provider which ID forms it accepts and whether a second form is required; do not rely on a photocopy or a photo on your phone.

Your registration confirmation and course materials

Carry the confirmation email or enrollment receipt and any materials the provider told you to bring. OSHA 510 is a trainer course, so expect to use the OSHA standards (29 CFR 1910 and 1926) and the course textbook during exercises. Confirm with the provider which references are allowed at your desk versus provided in class.

A current copy of the OSHA standards you will cite

Many candidates annotate a personal copy of 29 CFR 1910 and 1926. Tab the subparts you use most: walking-working surfaces (1910 Subpart D), PPE (1910 Subpart I), hazardous materials (1910 Subpart H), and construction fall, scaffold, and excavation rules (1926 Subparts M, L, and P). Practice finding a citation in under a minute.

Notebook, pens, and highlighters

Bring more than one pen and a highlighter. You will take notes during presentations and draft answers for the written and presentation-based assessments. Confirm with the provider whether scratch paper is supplied or whether you must bring your own.

A basic calculator or the calculator on an approved device

Some exercises involve exposure limits, noise dose, or fall-distance calculations. Confirm with the provider whether a phone-based calculator is allowed in the room or whether you need a standalone calculator.

Know the schedule and arrival time

OSHA 510 typically runs multiple full days, often 8:00 a.m. to 4:00 or 5:00 p.m., with a written exam near the end and a short teaching presentation. Reconfirm start time, room, and parking with the provider; arrive 20 to 30 minutes early to sign in and settle.

Review the four focus areas the course emphasizes

Be ready to explain hazard recognition, the hierarchy of controls, the difference between OSHA standards and consensus standards such as ANSI, and how to locate and interpret a standard. These themes recur in discussions and assessments.

Prepare a short teaching segment

OSHA 510 requires participants to present a brief training topic, often 10 to 15 minutes with a written lesson plan. Choose a narrow topic you know well (for example, scaffold inspection or lockout/tagout basics), write objectives, and rehearse aloud. Confirm the exact length, topic rules, and grading criteria with the provider.

Plan food, water, and medication

Days are long and rooms are often cold or dry. Bring water, a snack, and any prescription medication. Confirm with the provider whether food and drink are allowed in the classroom and how lunch breaks are scheduled.

Leave distractions at home or in the car

Phones, smartwatches, and other devices are commonly restricted during assessments. Confirm with the provider what must be stowed and where, and plan how you will be reached in an emergency.

Get contact details for the provider

Save the training coordinator's phone number and email so you can report a delay, illness, or scheduling question. If you must miss a session, ask in advance how make-up time is handled, since attendance requirements are set by the provider.

Rest and a realistic study plan

Do not plan to cram the standards the night before. Sleep, review your tabbed references and lesson plan, and arrive alert. Fatigue hurts more than one extra hour of reading helps.

Plan the day

72 hours before

Confirm logistics with the provider: dates, daily start and end times, location, parking, what to bring, and whether references or calculators are permitted at your desk. Re-read the course outline and note the assessment format, including the written exam and the teaching presentation.

72 hours before

Do a focused standards review. Practice locating citations quickly in 29 CFR 1910 and 1926, and be able to explain the hierarchy of controls, hazard recognition methods such as job hazard analysis, and the difference between OSHA standards and consensus standards. Use your own tabbed copy rather than a borrowed one.

72 hours before

Finish and rehearse your teaching presentation. Write clear objectives, an outline, and a short handout or visual aid if allowed. Time yourself aloud twice. Confirm with the provider what visual aids and equipment are available in the room.

24 hours before

Pack your bag: ID, confirmation, tabbed standards, notebook, pens, highlighters, calculator if allowed, water, snack, and medication. Lay out clothing and set two alarms. Check traffic or transit for the morning.

24 hours before

Do a light review only. Skim your notes and the key subparts, review your lesson plan once, then stop. Eat a normal meal, avoid alcohol, and aim for a full night's sleep.

Morning of

Eat breakfast and arrive 20 to 30 minutes early to sign in. Keep your ID and confirmation accessible. Silence and stow your phone and smartwatch as directed. Skim your tabbed references briefly, then put them away and settle in.

During the test

Read each question fully and note key words such as 'employer', 'employee', 'minimum', and 'most likely'. Answer what you know first, flag uncertain items, and return to them. For citation questions, use your tabbed standards calmly rather than guessing.

During the test

For the teaching presentation, state objectives up front, keep to the time limit, make eye contact, and summarize at the end. If you lose your place, pause, breathe, and continue from your outline. Leave a minute for questions if the format allows.

After the test

Ask the instructor how and when results are reported and what the process is if you need to retake or make up a session. Record any follow-up deadlines for receiving your completion documentation.

Rules to check

  • Bring the original government-issued photo ID you registered with. Confirm with the provider which forms of ID it accepts and whether a second form is required; expired or photocopied IDs are commonly refused.

  • Attend every scheduled session. OSHA 510 has attendance requirements, and missing time typically means you cannot complete the course. Confirm with the provider its exact attendance and make-up policy before you enroll.

  • Keep phones, smartwatches, and other devices silenced and stowed during assessments unless the provider says otherwise. Confirm with the provider what is permitted in the room.

  • Follow the provider's rules on breaks. Short breaks are usually scheduled, and leaving the room during an assessment may need permission. Ask the instructor at the start rather than assuming.

  • Use only references and materials the provider allows at your desk. If you are unsure whether a calculator, notes, or a textbook is permitted, ask before the assessment begins.

  • Do your own work. Copying another participant's answers or presenting someone else's lesson plan is a conduct violation and can result in failure or removal. Confirm with the provider how conduct issues are handled.

  • Scoring and passing criteria are set by the provider and the course requirements. Ask the instructor to explain the written exam format, the presentation grading, and the passing threshold at the start of the course rather than guessing.

  • Raise problems early. If you are ill, late, or have a scheduling conflict, tell the training coordinator immediately so options can be discussed. Do not wait until the final day.

OSHA 510 FAQ

How many OSHA 510 practice questions are available?

The practice set has 200 OSHA 510 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many OSHA 510 flashcards are available?

The flashcard set has 32 OSHA 510 cards. Each card shows the term and its definition.

Which topics does the OSHA 510 study material cover?

The OSHA 510 study material has 15 sections, including OSHA Act: Employer Duties, Inspections, and Enforcement, Choosing the Right Standard: 1910 vs. 1926, and Subpart C: General Safety and Health Provisions.