OSHA 30 overview

  • 200 practice questions
  • 32 flashcards
  • 8 study guide topics
  • 38 key terms

What you'll study

  • Introduction to OSHA12.5%
  • Walking-Working Surfaces and Fall Protection12.5%
  • Exit Routes, Emergency Action Plans, and Fire Prevention12.5%
  • Electrical Safety12.5%
  • Personal Protective Equipment12.5%
  • Hazard Communication12.5%
  • Materials Handling, Storage, Use, and Disposal12.5%
  • Machine Guarding12.5%

The OSHA 30-Hour Outreach Training Program is a voluntary hazard-awareness training program administered by OSHA and delivered by OSHA-authorized Outreach trainers. It is offered in Construction, General Industry, and Maritime, along with a 15-hour Disaster Site Worker class. The 30-hour class is intended for supervisors or workers with some safety responsibility; the shorter 10-hour class is aimed at general worker awareness. Instruction covers the recognition, avoidance, abatement, and prevention of common safety and health hazards in the relevant industry, plus workers' rights, employer responsibilities, and how to file a complaint. Students who attend and successfully complete the entire class, including all requisite topics and the minimum number of contact hours, receive a student course completion card. Two points matter for planning: OSHA does not require a test, and it is at the discretion of the trainer to determine whether a student has successfully completed the class. Also, Outreach training does not fulfill an employer's obligation to train workers under specific OSHA standards, and no Outreach course is considered a certification. Because content is awareness-level and industry-specific, preparation should center on hazard identification and control in your own workplace, workers' rights, and the complaint process.

Common mistakes

On a reporting scenario, the candidate selects the 24-hour window for a work-related fatality, treating the fatality and hospitalization deadlines as the same number.

Both deadlines are usually memorized together as a single 'report it right away' fact, so the two numbers bleed into each other under time pressure.

What to do instead

Anchor the pair: 8 hours for a fatality (only), 24 hours for in-patient hospitalization, amputation, or loss of an eye. Both are reported directly to OSHA, not just recorded on the 300 log.

The candidate applies a 6-foot fall protection trigger height to a general industry walking-working surface scenario.

The 6-foot number is the most widely repeated fall-protection figure, so it gets applied to every industry regardless of which standard the stem cites.

What to do instead

Tie the trigger height to the standard before answering: general industry 4 feet (29 CFR 1910.28), fixed ladders 5 feet, construction 6 feet, scaffolds 10 feet. Read the citation in the stem first, then pick the number.

The candidate accepts a guardrail system with a top rail installed at 48 inches as compliant.

The candidate remembers 'about waist-high' rather than the actual tolerance band, and 48 inches sounds close enough to be plausible.

What to do instead

Commit the dimension set: top rail 42 inches plus or minus 3 inches (39 to 45 inches), midrail at roughly 21 inches, and the top rail must withstand a 200-pound load applied in any downward or outward direction.

The candidate states that a written emergency action plan is required for every employer, regardless of headcount.

The written-document requirement is taught as a blanket rule, so the small-employer exception is never encountered in study notes and looks like a trick option.

What to do instead

Keep the threshold handy: 10 or fewer employees may communicate the plan orally; more than 10 requires it in writing. Either way the plan must be reviewed with each employee on initial assignment, when responsibilities change, and when the plan changes.

The candidate uses a 6-foot figure for the working space in front of electrical equipment, often by confusing it with the dedicated space above the equipment.

Three feet feels too shallow for a person to work in, so 6 feet sounds safer and matches the 'six feet of dedicated space above' fact that is also in the standard.

What to do instead

Separate the two dimensions: the working space is 30 inches wide and 36 inches deep (3 feet) for equipment up to 600 volts, deepening with voltage and with exposed live parts on the far side; the 6-foot figure applies to the dedicated space above the equipment.

The candidate says the employer must pay for all required PPE and therefore flags non-specialty safety-toe footwear and non-specialty prescription safety eyewear as employer-paid items.

The general rule ('employer pays for PPE') is learned alone, and the shoe and eyewear carve-outs are a short list that is easy to skip during review.

What to do instead

Memorize the short exception list: employer pays for required PPE except non-specialty safety-toe footwear and non-specialty prescription safety eyewear when the employee is allowed to wear them off the job site. Anything specialized or required by the hazard stays employer-paid.

The candidate marks as non-compliant a portable container into which a hazardous chemical was poured for the immediate use of the employee who poured it, on the ground that no full label is on it.

The 'every container must be labeled' rule is over-learned, and the immediate-use exemption for portable containers is a narrow exception that is rarely memorized.

What to do instead

Know the exception precisely: a portable container is exempt from labeling only while the chemical is for the immediate use of the employee who performed the transfer. All other secondary containers need a workplace label with the product identifier and the hazard information.

The candidate treats the safety data sheet requirement as satisfied by keeping a single SDS binder at a central office, or treats an SDS as unnecessary for a chemical used in small quantities.

Quantity feels intuitively tied to hazard, and a central binder looks organized, so neither option triggers doubt during the exam.

What to do instead

Every hazardous chemical in the workplace needs an SDS, regardless of quantity, and it must be readily accessible to employees in their work area during each shift. Electronic access is acceptable only if there is a backup means and no barriers to immediate access.

The candidate answers that a powered industrial truck operator must be formally retrained and recertified every 3 years.

The 3-year interval is remembered but attached to the wrong event, since the standard's 3-year requirement appears in the same paragraph as training.

What to do instead

The 3-year requirement is an evaluation of each operator's performance, not automatic retraining. Retraining is triggered by an accident or near miss, unsafe operation, a different type of truck, or a change in workplace conditions.

The candidate answers that guarding the point of operation alone satisfies the machine guarding requirements for a piece of equipment.

The phrase 'point of operation guarding' dominates study material, so the other hazard categories in the same standard are not recalled.

What to do instead

List all of them before choosing: point of operation, ingoing nip points, rotating parts, flying chips and sparks. Guards must also not create new hazards, and pulleys less than 7 feet above the floor or working platform must be guarded.

Exam requirements can change. Confirm current details with the exam provider.

OSHA 30 practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Introduction to OSHA

    Which federal department houses the Occupational Safety and Health Administration (OSHA)?

    1. Department of Health and Human Services
    2. Department of Commerce
    3. Department of Labor Correct answer.
    4. Environmental Protection Agency

    Explanation

    The OSH Act created OSHA within the U.S. Department of Labor, and the Secretary of Labor oversees it. This placement separates workplace enforcement from health research agencies.

  2. Question 2Introduction to OSHA

    Under Section 5(a)(1) of the OSH Act, what is the employer's general duty?

    1. Provide only the personal protective equipment that employees specifically request in writing
    2. Comply only with standards that OSHA has adopted and never with any other duty
    3. Guarantee that every employee is completely protected from all workplace risks at all times
    4. Furnish a workplace free from recognized hazards likely to cause death or serious physical harm Correct answer.

    Explanation

    Section 5(a)(1) imposes a general duty on employers to furnish employment and a place of employment free from recognized hazards that are causing or likely to cause death or serious physical harm. It applies even when no specific standard addresses the hazard.

  3. Question 3Introduction to OSHA

    How quickly must an employer report a work-related fatality to OSHA?

    1. Within 30 days
    2. Within 72 hours
    3. Within 8 hours Correct answer.
    4. Within 24 hours

    Explanation

    Employers must report a work-related fatality to OSHA within 8 hours. In-patient hospitalizations, amputations, and losses of an eye must be reported within 24 hours.

  4. Question 4Introduction to OSHA

    Which action is an employee right under the OSH Act?

    1. To issue citations to coworkers for unsafe acts
    2. To file a complaint and request an OSHA inspection Correct answer.
    3. To inspect other employers' injury and illness records
    4. To set the penalty amounts for violations

    Explanation

    Employees may file a complaint with OSHA and request an inspection; they may also participate in inspections and access injury records. Citations and penalties are issued by OSHA, not by employees.

  5. Question 5Introduction to OSHA

    What must an employer do with the OSHA 'It's the Law' poster?

    1. Post it where employees can see it Correct answer.
    2. Keep it in a locked office
    3. Post it only after an inspection
    4. Mail it to OSHA annually

    Explanation

    The OSHA poster informs employees of their rights and must be displayed where employees can readily see it. Failure to post can itself be a violation.

  6. Question 6Introduction to OSHA

    A state that operates its own occupational safety and health plan must meet which requirement?

    1. Cover only construction employers
    2. Be at least as effective as federal OSHA Correct answer.
    3. Eliminate employee complaint rights
    4. Adopt only advisory standards with no enforcement

    Explanation

    An OSHA-approved state plan must be at least as effective as the federal program, including standards and enforcement. States may adopt stricter requirements.

  7. Question 7Introduction to OSHA

    Federal OSHA standards generally apply to which group?

    1. Private-sector employers and their employees Correct answer.
    2. Self-employed individuals with no employees
    3. Immediate family members working on a family farm
    4. State and local government employees in every state

    Explanation

    Federal OSHA covers most private-sector employers and employees; state and local government workers are covered only in states with approved plans, and certain self-employed and family farm workers are excluded.

  8. Question 8Introduction to OSHA

    When an OSHA standard requires personal protective equipment, who pays for it?

    1. The employee through a payroll deduction spread over time
    2. The employee's union through its safety fund
    3. The equipment manufacturer as part of its warranty
    4. The employer, at no cost to the employee Correct answer.

    Explanation

    When an OSHA standard requires PPE, the employer must provide it at no cost to employees. The employer also must ensure the equipment fits and is maintained.

  9. Question 9Introduction to OSHA

    A violation is classified as serious when there is:

    1. A first-aid injury with no lost work time or medical treatment beyond first aid
    2. A substantial probability of death or serious physical harm Correct answer.
    3. A hazard that only employees happen to notice
    4. Any paperwork error that does not affect safety

    Explanation

    A serious violation exists when there is a substantial probability that death or serious physical harm could result from a condition the employer knew or should have known about. It does not require that an injury actually occurred.

  10. Question 10Introduction to OSHA

    A willful violation is one that the employer commits with:

    1. An unintentional clerical mistake in recordkeeping
    2. No knowledge of the standard because the employer never read the regulation
    3. Intentional disregard for, or plain indifference to, the law Correct answer.
    4. A good-faith effort to comply that falls short

    Explanation

    A willful violation involves intentional disregard of or plain indifference to OSHA requirements. Good-faith efforts or lack of knowledge can negate willfulness.

  11. Question 11Introduction to OSHA

    Which condition has the highest priority for an OSHA inspection?

    1. Imminent danger Correct answer.
    2. A follow-up inspection
    3. An employee complaint about a non-serious hazard
    4. A programmed inspection of a high-hazard industry

    Explanation

    OSHA prioritizes inspections in this order: imminent danger, fatality/catastrophe, employee complaints, programmed high-hazard inspections, and follow-ups. Imminent danger is first because death or serious harm could occur immediately.

  12. Question 12Introduction to OSHA

    How long does an employer have to contest an OSHA citation?

    1. 30 calendar days from receipt
    2. 15 working days from receipt Correct answer.
    3. 6 months from receipt
    4. 5 calendar days from receipt

    Explanation

    An employer must contest a citation, penalty, or abatement date in writing within 15 working days of receiving it. Otherwise, the citation becomes a final order.

  13. Question 13Introduction to OSHA

    Which OSHA form is the Log of Work-Related Injuries and Illnesses?

    1. Form 301
    2. Form 101
    3. Form 300A
    4. Form 300 Correct answer.

    Explanation

    Form 300 is the Log of Work-Related Injuries and Illnesses. Form 301 is the incident report, and Form 300A is the annual summary.

  14. Question 14Introduction to OSHA

    When must an employer post the annual summary of work-related injuries and illnesses (Form 300A)?

    1. For 3 days after a citation is issued
    2. February 1 through April 30 Correct answer.
    3. Only during an OSHA inspection
    4. January 1 through December 31

    Explanation

    The annual summary of injuries and illnesses must be posted from February 1 through April 30. It summarizes the prior calendar year's log.

  15. Question 15Introduction to OSHA

    Who may accompany an OSHA compliance officer during a workplace inspection?

    1. An employee representative authorized by employees Correct answer.
    2. The company president and no other person under any circumstances
    3. Any member of the public who requests access
    4. Only a police officer assigned to the site

    Explanation

    The OSH Act allows an authorized employee representative to accompany the compliance officer during the walkaround. The representative can be a coworker or a union representative.

  16. Question 16Introduction to OSHA

    What happens at the opening conference of an OSHA inspection?

    1. The compliance officer explains the purpose and scope of the inspection Correct answer.
    2. The employer pays the proposed penalty and waives all rights to contest
    3. The compliance officer issues the final citation and closes the case
    4. Employees vote on whether to allow the compliance officer to enter

    Explanation

    At the opening conference, the compliance officer explains why OSHA is there, the scope of the inspection, and the standards that may apply. The closing conference discusses findings and abatement.

  17. Question 17Introduction to OSHA

    How long does an employee generally have to file a retaliation complaint under OSH Act Section 11(c)?

    1. 30 days Correct answer.
    2. 6 months
    3. 3 years
    4. 1 year

    Explanation

    Section 11(c) prohibits retaliation for exercising rights such as filing a complaint. Complaints must generally be filed within 30 days of the alleged retaliation.

  18. Question 18Introduction to OSHA

    After receiving an OSHA citation, where and for how long must the employer post it?

    1. Only if an employee submits a written request to the area director
    2. At or near the violation for 3 working days or until abatement Correct answer.
    3. For exactly 30 calendar days regardless of whether the hazard is corrected
    4. Only in the corporate headquarters for a full calendar year after the citation becomes final

    Explanation

    The employer must post the citation at or near the violation for 3 working days or until the hazard is abated, whichever is longer. This informs employees of the hazard and its correction.

  19. Question 19Introduction to OSHA

    What does 'abatement' mean in OSHA enforcement?

    1. Contesting the citation before the Review Commission
    2. Correcting the hazard cited Correct answer.
    3. Requesting a warrant from a federal judge
    4. Paying the proposed monetary penalty

    Explanation

    Abatement means fixing the cited condition so it no longer violates the standard or general duty clause. Employers must certify abatement and may face failure-to-abate penalties.

  20. Question 20Introduction to OSHA

    What is a key feature of OSHA's On-Site Consultation Program?

    1. It is available only to federal agencies and their contractors
    2. It requires employees to waive their right to file complaints
    3. It replaces all enforcement inspections for participating employers
    4. It is separate from enforcement and does not propose penalties Correct answer.

    Explanation

    The On-Site Consultation Program is a free, confidential service for small employers, separate from enforcement. Consultants do not issue citations or propose penalties if the employer commits to correcting hazards.

  21. Question 21Introduction to OSHA

    Which employer is generally outside federal OSHA's jurisdiction unless an OSHA-approved state plan covers it?

    1. A private manufacturing plant that ships products across state lines
    2. A private hospital providing emergency and surgical services
    3. A municipal fire department in a state without an OSHA-approved plan Correct answer.
    4. A private construction company operating on a multi-story commercial building site

    Explanation

    Federal OSHA generally does not cover state and local government employees unless the state has an OSHA-approved plan. Private employers remain under federal jurisdiction in non-plan states.

  22. Question 22Introduction to OSHA

    To establish a General Duty Clause violation, OSHA must show:

    1. Employee misconduct, lost work time, and a written warning
    2. A specific OSHA standard, an actual injury, and a citation issued within six months
    3. An employer policy, a union contract, and a monetary penalty
    4. A recognized hazard, likely serious harm, and a feasible means of abatement Correct answer.

    Explanation

    To establish a General Duty Clause violation, OSHA must show a recognized hazard, that the hazard was likely to cause death or serious harm, and that a feasible means of abatement existed. A specific standard is not required.

  23. Question 23Introduction to OSHA

    Which set correctly lists the Voluntary Protection Programs recognition levels?

    1. A, B, and C
    2. Star, Merit, and Demonstration Correct answer.
    3. Gold, Silver, and Bronze
    4. Initial, Intermediate, and Final

    Explanation

    VPP recognizes worksites with exemplary safety and health programs at three levels: Star, Merit, and Demonstration. Star is the highest level for outstanding programs.

  24. Question 24Introduction to OSHA

    Within what period must OSHA issue a citation for a violation?

    1. 6 months after the violation occurred Correct answer.
    2. 24 hours after the compliance officer first observes the condition
    3. 30 days after the employer receives the inspection report
    4. 1 year after the violation occurred

    Explanation

    OSHA must issue a citation within 6 months after the violation occurred. This statutory limit applies to citations, though abatement and penalty collections can follow later.

  25. Question 25Introduction to OSHA

    An employee refuses to work because of a workplace hazard. Which condition generally supports a good-faith refusal under OSHA principles?

    1. A request for higher pay before the employee will perform the task
    2. A belief that the work is inconvenient rather than genuinely dangerous
    3. A general dislike of the assigned task combined with a coworker's unsupported rumor
    4. A reasonable belief of imminent death or serious injury with no reasonable alternative Correct answer.

    Explanation

    A good-faith refusal to work may be protected when the employee reasonably believes there is imminent danger of death or serious injury and no reasonable alternative exists. The fear must be objectively reasonable, not a general dislike.

  26. Question 26Walking-Working Surfaces and Fall Protection

    In general industry workplaces, at what height above a lower level must employees be protected from falling?

    1. 6 feet (1.8 m)
    2. 4 feet (1.2 m) Correct answer.
    3. 10 feet (3 m)
    4. 15 feet (4.6 m)

    Explanation

    OSHA's walking-working surfaces standard requires fall protection for general industry employees working 4 feet or more above a lower level. Different thresholds apply in other settings, such as 6 feet in construction.

  27. Question 27Walking-Working Surfaces and Fall Protection

    What is the required height of the top edge of a guardrail system above the walking-working surface?

    1. 45 inches (114 cm)
    2. 30 inches (76 cm)
    3. 42 inches (107 cm), plus or minus 3 inches Correct answer.
    4. 36 inches (91 cm)

    Explanation

    Guardrail systems must have a top rail whose top edge sits 42 inches above the walking-working surface, with a tolerance of plus or minus 3 inches. This height is designed to catch a worker's body before it passes over the edge.

  28. Question 28Walking-Working Surfaces and Fall Protection

    What is the maximum uniform spacing allowed between rungs, cleats, or steps on a portable ladder?

    1. 18 inches (46 cm)
    2. 12 inches (30 cm) Correct answer.
    3. 8 inches (20 cm)
    4. 10 inches (25 cm)

    Explanation

    Portable ladder rungs, cleats and steps must be spaced no more than 12 inches apart and spaced uniformly along the ladder. Wider or uneven spacing makes climbing awkward and increases slip risk.

  29. Question 29Walking-Working Surfaces and Fall Protection

    A worker finds a portable ladder with a cracked side rail. What is the correct action?

    1. Remove it from service and tag it with a 'Do Not Use' warning Correct answer.
    2. Report the defect at the end of the shift and keep using it
    3. Mark it with tape and leave it in place for light-duty work
    4. Shorten the ladder and continue using it as a step stool

    Explanation

    Any ladder with a structural or other defect must be immediately withdrawn from service and tagged with a warning such as 'Dangerous: Do Not Use' until it is repaired or destroyed. A cracked rail can fail without warning under a worker's weight.

  30. Question 30Walking-Working Surfaces and Fall Protection

    What must an employer ensure about the load-carrying capacity of each walking-working surface?

    1. It can support the maximum intended load Correct answer.
    2. It can support the weight of the tools stored on it
    3. It can support at least 500 pounds per square foot
    4. It can support twice the weight of the heaviest worker

    Explanation

    Each walking-working surface must be able to support the maximum intended load, meaning the total combined weight of employees, equipment and materials expected on it. There is no blanket pounds-per-square-foot figure in the rule.

  31. Question 31Walking-Working Surfaces and Fall Protection

    When must a stairway be equipped with at least one handrail?

    1. When it has two or more risers
    2. When it is wider than 44 inches
    3. When more than ten employees use it
    4. When it has four or more risers Correct answer.

    Explanation

    A stairway with four or more risers, or that rises more than 30 inches, must have at least one handrail. Short flights below that threshold are not required to have one under this rule.

  32. Question 32Walking-Working Surfaces and Fall Protection

    Which practice is acceptable when an employee is climbing or working on a portable ladder?

    1. Moving the ladder sideways while a worker is standing on it
    2. Standing on the top step of a stepladder to reach higher
    3. Tying two short ladders together to gain extra height
    4. Climbing while facing the ladder and holding its side rails Correct answer.

    Explanation

    Employees must climb facing the ladder and use the side rails or rungs as intended. Ladders must never be moved, shifted or extended while an employee is on them.

  33. Question 33Walking-Working Surfaces and Fall Protection

    Where must the midrail of a guardrail system be installed?

    1. At the walking surface as a toe board
    2. Exactly 36 inches above the surface
    3. Midway between the top rail and the walking surface Correct answer.
    4. On top of the top rail

    Explanation

    A midrail is installed midway between the top edge of the guardrail and the walking-working surface; on a standard 42-inch guardrail this places it about 21 inches up. The midrail closes the gap so a worker cannot slide under the top rail.

  34. Question 34Walking-Working Surfaces and Fall Protection

    How far should the base of a 20-foot non-self-supporting extension ladder be set out from the wall it leans against?

    1. 8 feet (2.4 m)
    2. 10 feet (3 m)
    3. 2 feet (0.6 m)
    4. 5 feet (1.5 m) Correct answer.

    Explanation

    Non-self-supporting ladders are set at roughly a 4:1 ratio, so the base is one-quarter of the working length away from the upper support. One-quarter of 20 feet is 5 feet.

  35. Question 35Walking-Working Surfaces and Fall Protection

    A portable ladder is used to climb onto a roof. How far must the ladder extend above the landing surface?

    1. 1 foot (0.3 m)
    2. 3 feet (0.9 m) Correct answer.
    3. It may stop flush with the landing
    4. 5 feet (1.5 m)

    Explanation

    A ladder used to access an upper landing must extend at least 3 feet above that landing so the climber has a handhold while stepping on and off. A ladder that stops flush with the roof gives nothing to grip.

  36. Question 36Walking-Working Surfaces and Fall Protection

    A floor opening is protected with a plywood cover. What must be true of that cover?

    1. It must be painted with yellow and black diagonal stripes
    2. It must be taken off whenever employees are working nearby
    3. It must hold twice the intended load and be marked 'HOLE' or 'COVER' Correct answer.
    4. It must be fastened with at least eight nails or screws

    Explanation

    Hole covers must support at least twice the weight of the employees, equipment and materials that could be placed on them, and must be marked with the word 'HOLE' or 'COVER'. They must also be secured against displacement.

  37. Question 37Walking-Working Surfaces and Fall Protection

    What is the minimum anchorage strength required for a personal fall arrest system, per attached employee?

    1. 3,000 pounds (13.3 kN)
    2. 2,500 pounds (11.1 kN)
    3. 1,000 pounds (4.4 kN)
    4. 5,000 pounds (22.2 kN) Correct answer.

    Explanation

    Anchorages used for personal fall arrest must be capable of supporting at least 5,000 pounds per employee attached, or be designed by a qualified person as part of a complete system with a safety factor of at least two.

  38. Question 38Walking-Working Surfaces and Fall Protection

    What are the maximum riser height and minimum tread depth for a standard stairway?

    1. 6-inch riser; 10-inch tread
    2. 7-inch riser; 11-inch tread Correct answer.
    3. 9-inch riser; 9-inch tread
    4. 8-inch riser; 12-inch tread

    Explanation

    Standard stairway risers must be no more than 7 inches high and treads at least 11 inches deep, with riser and tread dimensions kept uniform throughout the flight. Uniformity prevents missteps caused by unexpected changes in step geometry.

  39. Question 39Walking-Working Surfaces and Fall Protection

    At what height above the stair treads must handrails be installed?

    1. 42 to 45 inches (107 to 114 cm)
    2. 38 to 42 inches (97 to 107 cm)
    3. 30 to 38 inches (76 to 97 cm) Correct answer.
    4. 24 to 30 inches (61 to 76 cm)

    Explanation

    Handrails must be between 30 and 38 inches high, measured vertically from the stair tread nosing. This range fits most users so the rail can be gripped comfortably for support.

  40. Question 40Walking-Working Surfaces and Fall Protection

    A guardrail system used as fall protection must be able to withstand what minimum force applied to its top rail?

    1. 50 pounds (222 N)
    2. 500 pounds (2,224 N)
    3. 100 pounds (445 N)
    4. 200 pounds (890 N) Correct answer.

    Explanation

    Guardrail systems must withstand a force of at least 200 pounds applied in an outward or downward direction near the top edge, without failing or deflecting beyond the allowed limits. This ensures the rail can stop a worker who leans or falls against it.

  41. Question 41Walking-Working Surfaces and Fall Protection

    When an employee needs personal fall arrest protection, what body-wearable component must the system use?

    1. A full-body harness Correct answer.
    2. A chest strap with a single shoulder loop
    3. A waist belt fitted with a rope grab
    4. A body belt worn around the waist

    Explanation

    Fall arrest must be accomplished with a full-body harness, which spreads arresting forces across the torso and thighs. Body belts are prohibited for fall arrest because they concentrate that force on the waist and can cause serious injury.

  42. Question 42Walking-Working Surfaces and Fall Protection

    At what depth must employees working at the edge of an excavation be protected from falling?

    1. 8 feet (2.4 m)
    2. 4 feet (1.2 m)
    3. 10 feet (3 m)
    4. 6 feet (1.8 m) Correct answer.

    Explanation

    Employees at the edge of an excavation 6 feet or more deep must be protected from falling by a guardrail system, fence or barricade. The deeper threshold reflects the more serious consequences of a fall into an open cut.

  43. Question 43Walking-Working Surfaces and Fall Protection

    Employees work on a platform 3 feet above machinery with exposed moving parts. What does OSHA require?

    1. Fall protection only when the machinery is running
    2. Only a warning sign posted at the platform edge
    3. Protection by a guardrail system or a travel restraint system Correct answer.
    4. Nothing, because the platform is below 4 feet

    Explanation

    Where employees are exposed to dangerous equipment such as machinery with moving parts, protection is required even at heights below the normal 4-foot trigger. At these lower heights a guardrail system or travel restraint system must be provided.

  44. Question 44Walking-Working Surfaces and Fall Protection

    Which circumstance requires an employer to retrain an employee on fall protection?

    1. Every six months, on a fixed schedule
    2. When the employee shows they no longer understand the training Correct answer.
    3. Whenever a new supervisor is assigned to the crew
    4. Only after an injury that must be recorded

    Explanation

    Retraining is required when changes in the workplace make earlier training obsolete, when an employee's conduct shows the training was not understood, or when the employee otherwise lacks the required knowledge. There is no fixed calendar interval for retraining in the rule.

  45. Question 45Walking-Working Surfaces and Fall Protection

    How must a portable dockboard be held in position while it is in use at a loading dock?

    1. By having a worker stand on the dock end
    2. By spreading sand under its underside
    3. By placing a pallet against its outer edge
    4. By anchoring it or using devices that prevent slipping Correct answer.

    Explanation

    Portable dockboards must be secured in position, either by anchoring them or by using devices that prevent slipping, so they cannot shift as loads cross them. They also need handholds or another effective means for safe handling.

  46. Question 46Walking-Working Surfaces and Fall Protection

    A fixed ladder installed in 2020 rises 30 feet to a roof. What fall protection must be provided to employees climbing it?

    1. A well built around the ladder
    2. No protection, because the climb is under 50 feet
    3. A cage enclosing the ladder
    4. A ladder safety system or personal fall arrest system Correct answer.

    Explanation

    Fixed ladders that extend more than 24 feet above a lower level must be equipped with a personal fall arrest system or a ladder safety system. For ladders installed after November 19, 2018, cages and wells are no longer accepted as the required protection.

  47. Question 47Walking-Working Surfaces and Fall Protection

    What is the maximum arresting force a personal fall arrest system may impose on an employee wearing a full-body harness?

    1. 2,500 pounds (11 kN)
    2. 5,000 pounds (22 kN)
    3. 1,800 pounds (8 kN) Correct answer.
    4. 900 pounds (4 kN)

    Explanation

    Personal fall arrest systems must limit the maximum arresting force on the body to 1,800 pounds when a full-body harness is used. The harness distributes that force across strong parts of the body, unlike a belt.

  48. Question 48Walking-Working Surfaces and Fall Protection

    What is the greatest deceleration distance a personal fall arrest system is allowed to produce?

    1. 1.5 feet (0.5 m)
    2. 3.5 feet (1.1 m) Correct answer.
    3. 2.5 feet (0.8 m)
    4. 5 feet (1.5 m)

    Explanation

    A personal fall arrest system must bring a fall to a stop within a deceleration distance of 3.5 feet or less. That limit, combined with the free-fall and harness stretch allowances, determines how much clearance must exist below the work surface.

  49. Question 49Walking-Working Surfaces and Fall Protection

    What is the minimum height of a toe board installed on a guardrail system?

    1. 3 inches (7.6 cm)
    2. 4 inches (10 cm)
    3. 2 inches (5 cm)
    4. 3.5 inches (8.9 cm) Correct answer.

    Explanation

    Toe boards must be at least 3.5 inches high from the top edge to the level of the walking-working surface, and are mounted no more than one-quarter inch above it. They keep tools and materials from being kicked off an elevated surface.

  50. Question 50Walking-Working Surfaces and Fall Protection

    What is the minimum clear length required for the rungs of a fixed ladder?

    1. 12 inches (30 cm)
    2. 16 inches (41 cm) Correct answer.
    3. 18 inches (46 cm)
    4. 11.5 inches (29 cm)

    Explanation

    Rungs on fixed ladders must have a clear length of at least 16 inches so a climber's foot has adequate support. Fixed ladders must also be designed to carry two loads of 250 pounds each.

  51. Question 51Exit Routes, Emergency Action Plans, and Fire Prevention

    Under OSHA's exit route rules, how many exit routes must a typical workplace provide?

    1. Three routes in every occupied floor of a building
    2. Two routes, but only if more than 50 employees work on site
    3. At least two, located as far apart as practicable Correct answer.
    4. One route, provided it is at least 48 inches wide

    Explanation

    29 CFR 1910.36 requires at least two exit routes in each workplace, and they must be arranged as far apart as practicable so that a fire or smoke condition blocking one route still leaves another usable. A single route is allowed only in narrow situations where all occupants could evacuate safely.

  52. Question 52Exit Routes, Emergency Action Plans, and Fire Prevention

    How must exit route doors be secured while a building is occupied?

    1. Unlocked from the inside without a key or special knowledge Correct answer.
    2. Locked at all times to prevent unauthorized entry from outside
    3. Equipped with a padlock that employees can open using a shared security code
    4. Opened only by designated security staff during business hours

    Explanation

    Exit route doors must be openable from the inside without a key, tool, or special knowledge whenever the building is occupied, so occupants are never trapped by hardware during a fire. Locks that require a code or a staff member to release violate this requirement.

  53. Question 53Exit Routes, Emergency Action Plans, and Fire Prevention

    What is the minimum height of the letters forming the word "Exit" on an exit sign?

    1. 6 inches Correct answer.
    2. 10 inches
    3. 2 inches
    4. 4 inches

    Explanation

    29 CFR 1910.37 requires the word "Exit" to be in plainly legible letters at least 6 inches high, with strokes at least 3/4 inch wide. The size requirement ensures the sign can be recognized from a distance along the exit route.

  54. Question 54Exit Routes, Emergency Action Plans, and Fire Prevention

    A supervisor finds wooden pallets stacked in a corridor marked as an exit route. What does OSHA require?

    1. The pallets may stay if stacked flat against the wall
    2. The pallets may stay overnight if the corridor is 6 feet wide
    3. The pallets must be removed because exit routes must stay unobstructed Correct answer.
    4. The pallets may stay if the corridor is protected by sprinklers

    Explanation

    Exit routes must be kept free and unobstructed, and no materials or equipment may be placed in them, whether permanently or temporarily. Sprinkler protection or corridor width does not authorize storage in a required exit route.

  55. Question 55Exit Routes, Emergency Action Plans, and Fire Prevention

    What level of lighting is required along an exit route?

    1. Enough that a person with normal vision can see along the route Correct answer.
    2. Only during hours when the public is admitted
    3. At least 100 foot-candles measured at the floor
    4. Only while the building's fire alarm is sounding

    Explanation

    Each exit route must be adequately lighted so that an employee with normal vision can see along the route, and exit signs must remain visible. Lighting is required whenever the building is occupied, not only during emergencies or public hours.

  56. Question 56Exit Routes, Emergency Action Plans, and Fire Prevention

    A door along an exit access leads to a storage closet but looks like an exit. What must the employer do?

    1. Paint it a contrasting color with no sign
    2. Keep it locked from the outside at all times
    3. Mark it "Not an Exit" or identify its actual use Correct answer.
    4. Remove the door and replace it with an open archway

    Explanation

    Any doorway or passage along an exit access that could be mistaken for an exit must be marked "Not an Exit" or identified by a sign showing its actual use, such as "Closet." This prevents occupants from wasting time or entering a dead end during evacuation.

  57. Question 57Exit Routes, Emergency Action Plans, and Fire Prevention

    A workplace employs eight people. What does OSHA allow regarding the emergency action plan?

    1. Posting the plan only at the main entrance
    2. No emergency action plan of any kind
    3. Communicating the plan orally to employees Correct answer.
    4. Keeping the plan only at an off-site corporate office

    Explanation

    An emergency action plan must generally be in writing and kept at the workplace for employee review, but employers with 10 or fewer employees may communicate the plan orally. The plan's content requirements still apply regardless of the format.

  58. Question 58Exit Routes, Emergency Action Plans, and Fire Prevention

    Which element must be included in an emergency action plan?

    1. A schedule of fire drills signed by the local fire marshal
    2. A building floor plan stamped by a licensed engineer
    3. A roster of employees' home telephone numbers
    4. Procedures to account for all employees after evacuation Correct answer.

    Explanation

    The minimum elements of an emergency action plan include procedures for reporting emergencies, evacuation procedures and route assignments, accounting for all employees after evacuation, rescue and medical duties, and the name or job title of a contact person. Drill schedules, stamped drawings, and home phone lists are not required elements.

  59. Question 59Exit Routes, Emergency Action Plans, and Fire Prevention

    What does OSHA require of employees who help with evacuation during an emergency?

    1. They must be drawn from management ranks only
    2. They must be designated and trained to assist in evacuation Correct answer.
    3. They must be retrained on a monthly basis
    4. They must hold a state-issued firefighter certification

    Explanation

    The employer must designate and train employees to assist in a safe and orderly evacuation of other employees. The standard does not prescribe certification, rank, or a specific retraining interval for these assistants.

  60. Question 60Exit Routes, Emergency Action Plans, and Fire Prevention

    When must an employer review the emergency action plan with an employee?

    1. Only when the employee requests a copy of the plan
    2. Upon initial assignment and whenever the plan changes Correct answer.
    3. Only after an actual emergency has occurred
    4. Once every five years at a company-wide meeting

    Explanation

    The plan must be reviewed with each employee covered by it when the employee is initially assigned, when the employee's responsibilities under the plan change, and when the plan itself changes. A fixed multi-year cycle or a request-based approach does not meet the rule.

  61. Question 61Exit Routes, Emergency Action Plans, and Fire Prevention

    Which statement describes OSHA's requirement for the employee alarm system used to signal evacuation?

    1. It must be distinctive and recognizable as an evacuation signal Correct answer.
    2. It may share the elevator arrival chime as its signal
    3. It must be audible only in the main office area
    4. It must be tested only after an emergency occurs

    Explanation

    The employee alarm must be distinctive and recognizable as a signal to evacuate the work area or to perform actions designated in the emergency action plan. It must reach the employees who need to respond, not just a single office area.

  62. Question 62Exit Routes, Emergency Action Plans, and Fire Prevention

    Which item belongs in a fire prevention plan?

    1. A list of major fire hazards and their ignition sources Correct answer.
    2. A roster of employees trained in first aid
    3. The name of the company's property insurance carrier
    4. Evacuation route assignments for each department

    Explanation

    A fire prevention plan must list all major fire hazards, proper handling and storage of hazardous materials, potential ignition sources and their control, and the fire protection equipment needed for each major hazard. Evacuation assignments belong to the emergency action plan instead.

  63. Question 63Exit Routes, Emergency Action Plans, and Fire Prevention

    When must an employer inform employees about the fire hazards to which they are exposed?

    1. At the time of their initial assignment Correct answer.
    2. Only if an employee asks a supervisor
    3. Within 30 days of being hired
    4. Only during the annual fire drill

    Explanation

    The employer must inform employees of the fire hazards they are exposed to upon initial assignment and must review the parts of the fire prevention plan necessary for their self-protection. The information cannot wait for a drill or a request.

  64. Question 64Exit Routes, Emergency Action Plans, and Fire Prevention

    Which topic belongs in a fire prevention plan rather than an emergency action plan?

    1. Procedures for controlling accumulations of combustible waste Correct answer.
    2. Procedures for accounting for all employees after evacuation
    3. Procedures for employees who remain to perform critical operations
    4. Procedures for reporting a fire to the fire department

    Explanation

    Fire prevention plans address preventing ignition and limiting fuel, including procedures to control accumulations of flammable and combustible waste materials. Reporting, critical-operation staffing, and post-evacuation accounting are emergency action plan elements.

  65. Question 65Exit Routes, Emergency Action Plans, and Fire Prevention

    Where must an exit discharge lead?

    1. Onto an elevator lobby on the ground floor
    2. Into a designated interior muster room
    3. Directly outside or to a public way or open space Correct answer.
    4. Into an enclosed stairwell that security can lock at night

    Explanation

    An exit discharge must lead directly outside or to a street, walkway, refuge area, public way, or open space with access to the outside, and that area must be large enough for the occupants likely to use it. Routes that end inside the building or in a lockable stairwell do not qualify.

  66. Question 66Exit Routes, Emergency Action Plans, and Fire Prevention

    Which arrangement is prohibited for an exit access?

    1. A corridor that passes a sprinkler riser room with a self-closing door
    2. A corridor posted with illuminated directional signs
    3. An exit access through a bathroom that can be locked Correct answer.
    4. A corridor that leads to two separate, remotely located exits

    Explanation

    The exit access must not pass through a room that can be locked, such as a bathroom, and must not lead into a dead-end corridor. Such arrangements can trap occupants who are routed through a space that may be secured or that offers no way out.

  67. Question 67Exit Routes, Emergency Action Plans, and Fire Prevention

    What are the minimum width and height of an exit route under OSHA's design requirements?

    1. 44 inches wide and 8 feet high
    2. 36 inches wide and 7 feet high
    3. 28 inches wide and 6 feet 8 inches high Correct answer.
    4. 24 inches wide and 6 feet high

    Explanation

    Exit routes must be at least 28 inches wide and at least 6 feet 8 inches high at all points, and wider where the occupant load requires it. These dimensions keep the route usable by the number of employees expected to evacuate through it.

  68. Question 68Exit Routes, Emergency Action Plans, and Fire Prevention

    Which type of door does OSHA require for an exit route?

    1. A side-hinged swinging door Correct answer.
    2. A vertical-roll overhead door
    3. A sliding door with a motion sensor
    4. A revolving door with a push bar

    Explanation

    Exit route doors must be side-hinged swinging doors that swing in the direction of travel when serving a large occupant load. Sliding, revolving, and overhead doors do not meet the requirement because they can jam or obstruct rapid egress.

  69. Question 69Exit Routes, Emergency Action Plans, and Fire Prevention

    An enclosed exit stairwell connects four stories of a building. What fire-resistance rating must the enclosure have?

    1. 1 hour
    2. 2 hours Correct answer.
    3. 4 hours
    4. 30 minutes

    Explanation

    Exit enclosures connecting four or more stories must have a two-hour fire-resistance rating, while those connecting three or fewer stories require one hour. The longer rating protects the stairway long enough for occupants of taller buildings to descend.

  70. Question 70Exit Routes, Emergency Action Plans, and Fire Prevention

    How must exit routes be arranged with respect to hazardous areas?

    1. Employees must travel at least 200 feet along a protected corridor
    2. Employees must use a single designated route when a fire alarm sounds
    3. Employees avoid traveling toward a high hazard unless the path is shielded Correct answer.
    4. Employees must pass through the highest hazard area to reach the nearest exit

    Explanation

    Exit routes must be arranged so that employees will not have to travel toward a high hazard area unless the path of travel is effectively shielded by suitable partitions or physical barriers. The goal is to move people away from, not through, the hazard.

  71. Question 71Exit Routes, Emergency Action Plans, and Fire Prevention

    During renovations, a contractor must temporarily close a marked exit corridor. What does OSHA require?

    1. Employees must be given flashlights and keep using the corridor
    2. The corridor must stay open because exit routes may never be altered
    3. An alternate exit route must be provided before the corridor closes Correct answer.
    4. The corridor may close only on night shifts when fewer employees are present

    Explanation

    Exit routes must be maintained during construction, repairs, or alterations, and where a route is taken out of service the employer must provide alternate exit routes so protection is not reduced. Flashlights or a smaller night crew do not substitute for a safe, code-compliant route.

  72. Question 72Exit Routes, Emergency Action Plans, and Fire Prevention

    A fire prevention plan must identify by name or job title the employee responsible for which activity?

    1. Purchasing fire insurance coverage
    2. Control of fuel source hazards Correct answer.
    3. Conducting the annual fire drill
    4. Maintaining the emergency action plan

    Explanation

    The plan must name the employees, by name or job title, responsible for maintaining equipment used to prevent or control sources of ignition or fires and for controlling fuel source hazards. Drill leadership and business matters are outside this requirement.

  73. Question 73Exit Routes, Emergency Action Plans, and Fire Prevention

    A tenant hangs a large decorative banner across an exit route door. What does OSHA require?

    1. The banner may stay if an emergency light illuminates the door
    2. The banner is acceptable if it is flame-retardant and anchored at all four corners
    3. The door must stay free of decorations or signs that obscure it Correct answer.
    4. The banner may stay if it covers less than half of the door

    Explanation

    Exit route doors must be free of decorations or signs that obscure the visibility of the door, and exit routes must be kept free of explosive or highly flammable furnishings. Flame-retardant treatment or partial coverage does not cure an obscured exit door.

  74. Question 74Exit Routes, Emergency Action Plans, and Fire Prevention

    A fire door protecting an exit enclosure has been propped open for ventilation. What does OSHA require?

    1. It must be kept closed because it is a required safeguard Correct answer.
    2. It may stay propped if the building has a sprinkler system
    3. It may stay propped during warm weather only
    4. It may stay propped if a warning sign is posted on it

    Explanation

    Safeguards designed to protect employees during an emergency, such as sprinkler systems, alarm systems, fire doors, and exit lighting, must be in proper working order at all times. A self-closing fire door that is propped open no longer performs its function.

  75. Question 75Exit Routes, Emergency Action Plans, and Fire Prevention

    A plant's plan directs a boiler operator to shut down equipment before evacuating. How does this fit OSHA's emergency action plan requirements?

    1. The plan must require fire department approval before any shutdown
    2. The plan must cover employees who stay to perform critical operations Correct answer.
    3. The plan must forbid anyone from remaining after the alarm sounds
    4. The plan must assign all shutdown duties to the local fire brigade

    Explanation

    An emergency action plan must include procedures for employees who remain to operate critical plant operations before they evacuate. Because some tasks cannot be abandoned instantly, the plan must describe who stays, what they do, and how they then leave safely.

  76. Question 76Electrical Safety

    On a construction site, 120-volt single-phase, 15- and 20-ampere receptacle outlets that are not part of the permanent wiring must be protected by which of the following?

    1. A posted warning sign at each temporary panel
    2. An annual insulation resistance test of the service
    3. GFCIs or an assured grounding conductor program Correct answer.
    4. A three-wire cord on every tool that is plugged in

    Explanation

    Temporary receptacles on construction sites must have ground-fault protection, either through ground-fault circuit interrupters or through an assured equipment grounding conductor program that is described in writing and actually carried out. The requirement applies to 15- and 20-ampere, 120-volt single-phase receptacles that are not part of the permanent wiring. Relying on tool cords or signage does not satisfy it.

  77. Question 77Electrical Safety

    After a circuit has been locked out for repair, who may remove the lock?

    1. The employee who applied it, under the employer's procedures Correct answer.
    2. Any qualified person who verifies the work is finished
    3. The shift supervisor, after notifying the crew
    4. Any electrician on the crew who has completed LOTO training

    Explanation

    Lockout/tagout rules restrict removal of a lock to the person who applied it, following the employer's established procedure. This ensures the equipment is not reenergized while someone still believes it is safe. Only the employer's documented exception procedure allows another person to remove it.

  78. Question 78Electrical Safety

    Work on exposed conductors must be performed with the circuit deenergized unless...

    1. the circuit operates at less than 240 volts
    2. deenergizing would add hazards or is infeasible Correct answer.
    3. the task can be completed in under fifteen minutes
    4. the employee has at least five years of experience

    Explanation

    The general rule is that live parts are deenergized before employees work on or near them. The two recognized exceptions are when deenergizing introduces additional or increased hazards, and when deenergizing is infeasible because of equipment design or operational limitations. Voltage level, worker seniority, and task duration do not create exceptions.

  79. Question 79Electrical Safety

    Which of the following is an acceptable use of a flexible cord?

    1. Running through a doorway as a permanent feed
    2. Replacing permanent wiring inside a wall cavity
    3. Serving as the fixed wiring of a structure
    4. Connecting a portable appliance to a receptacle Correct answer.

    Explanation

    Flexible cords are permitted for connecting portable lamps and appliances and similar uses where flexibility is needed. They may not be used as a substitute for the fixed wiring of a structure, run through walls, ceilings, or floors, or used as permanent feeds in ways that subject them to damage.

  80. Question 80Electrical Safety

    Rubber insulating gloves must be air tested by the user...

    1. only after they have been cleaned and dried by hand
    2. once a month, regardless of use
    3. only when issued to a new employee
    4. before each day's use or if damage is suspected Correct answer.

    Explanation

    Insulating gloves are air tested to reveal cuts, punctures, and cracks that are hard to see. The test is done before each day's use and any time damage is suspected, such as after an incident that could have injured the rubber. Periodic laboratory retesting is a separate requirement.

  81. Question 81Electrical Safety

    An employee finds a portable drill with a frayed cord and a missing grounding pin. What should happen?

    1. Use the drill only on a GFCI-protected circuit
    2. Remove the drill from service until it is repaired Correct answer.
    3. Tape the frayed area and return the drill to service
    4. Tag the drill and leave the decision to the next shift

    Explanation

    Damaged portable electric equipment must be removed from service until it has been repaired and tested. A frayed cord and a missing grounding pin both defeat the equipment's protective features, so taping the cord or relying on a GFCI does not restore the tool to a safe condition.

  82. Question 82Electrical Safety

    Who may work on electrical circuit parts that have not been deenergized?

    1. Any employee wearing insulating footwear
    2. Only a qualified person or a supervised trainee Correct answer.
    3. Any employee who has read the company's electrical policy
    4. Any employee with a second person standing by

    Explanation

    Energized work is limited to qualified persons, plus employees in training who are under the direct supervision of a qualified person. Qualified status reflects training and demonstrated ability to recognize and avoid the hazards involved. Reading a policy, wearing footwear, or having a helper present does not qualify an employee.

  83. Question 83Electrical Safety

    What is the primary purpose of overcurrent protection on a branch circuit?

    1. To allow equipment to be locked out for service
    2. To prevent motors from starting too often
    3. To open the circuit before conductors overheat Correct answer.
    4. To reduce voltage drop on long runs

    Explanation

    Overcurrent devices open the circuit when current exceeds the conductor's ampacity, limiting heat that could damage insulation and ignite surrounding materials. They also protect equipment from fault currents. Voltage drop, motor cycling, and lockout are unrelated functions.

  84. Question 84Electrical Safety

    For work near an overhead power line energized at 50 kV or less, what minimum clearance must unqualified employees and their tools maintain?

    1. 6 feet
    2. 10 feet Correct answer.
    3. 25 feet
    4. 4 feet

    Explanation

    The general industry rule requires unqualified employees and the conductive objects they hold to stay at least 10 feet from overhead lines rated 50 kV or less. Greater voltages require added distance. Closer work is allowed only for qualified persons who use the required protective measures.

  85. Question 85Electrical Safety

    If a bucket truck contacts an energized overhead line, the operator should...

    1. try to drive the truck clear of the line
    2. climb down immediately and run from the truck
    3. lower the bucket to the ground before calling for help
    4. stay inside and warn others away until power is cut Correct answer.

    Explanation

    When equipment contacts an energized line, the operator should remain in the cab and keep others away until the line is deenergized, because stepping to earth while touching the vehicle can complete a circuit through the body. Movement of the equipment and nearby workers increases the chance of a second contact or recontact.

  86. Question 86Electrical Safety

    Which of the following is an OSHA-recognized alerting technique for electrical hazards?

    1. A warning delivered at the weekly safety meeting
    2. A verbal caution from the electrician
    3. A note in the crew's daily logbook
    4. An attendant stationed to warn employees away Correct answer.

    Explanation

    Alerting techniques for electrical hazards include safety signs and tags, barricades, and attendants stationed to warn and direct employees. These are intended to keep unqualified employees away from exposed energized parts at the moment of the hazard. General communications such as logbook entries or meeting reminders are not alerting techniques.

  87. Question 87Electrical Safety

    Rubber insulating gloves marked Class 00 have a maximum use voltage of...

    1. 500 volts AC Correct answer.
    2. 7,500 volts AC
    3. 1,000 volts AC
    4. 17,000 volts AC

    Explanation

    Rubber insulating gloves are classified by maximum use voltage, and Class 00 is the lowest class, rated for 500 volts AC. Class 0 is rated 1,000 volts, Class 1 is 7,500 volts, and Class 2 is 17,000 volts. Gloves must be selected so their class meets or exceeds the voltage of the circuit.

  88. Question 88Electrical Safety

    After a circuit is locked out, how should an electrician verify it is deenergized?

    1. Confirm the breaker handle is in the OFF position
    2. Test with a rated tester proven on a known live source Correct answer.
    3. Check that the lock and tag are properly attached
    4. Ask the equipment operator to confirm the shutdown

    Explanation

    Verification means testing the conductors with equipment rated for the voltage, and confirming the tester works by checking it on a known energized source before and after the test. Breaker position, someone's statement, and the presence of locks only show that a switching action was taken, not that the circuit is dead.

  89. Question 89Electrical Safety

    Under an assured equipment grounding conductor program, cord sets must be tested...

    1. before first use, after repairs, and at least every 3 months Correct answer.
    2. only when a shock is reported
    3. once a year by a licensed electrician
    4. once a week while in use

    Explanation

    An assured equipment grounding conductor program requires visual inspection before each day's use and continuity testing of cord sets and cord- and plug-connected equipment before first use, after repairs, and at intervals not exceeding three months. Receptacles that are not part of the permanent wiring are tested at intervals not exceeding six months, and the program must be described in writing.

  90. Question 90Electrical Safety

    Before an employee enters a space containing exposed energized parts, the employer must ensure that...

    1. portable heaters are available to keep the space dry
    2. a standby person is posted outside at all times
    3. the space is posted with the last inspection date
    4. the space is adequately illuminated for safe work Correct answer.

    Explanation

    Employees may not enter spaces with exposed energized parts unless the lighting lets them work safely and see the hazard. Adequate illumination is a basic work practice that reduces accidental contact. Standby persons, inspection postings, and heaters are not the requirement addressed here.

  91. Question 91Electrical Safety

    Training for qualified persons must include the skills needed to...

    1. operate the site's fire extinguishing equipment
    2. administer first aid for electrical burns
    3. distinguish live parts and determine their nominal voltage Correct answer.
    4. read architectural drawings for conduit layouts

    Explanation

    Qualified persons must be trained to tell exposed live parts from other parts of electric equipment, to determine the nominal voltage of exposed parts, and to understand the clearance distances and precautions that apply. This knowledge base is what separates qualified from unqualified employees.

  92. Question 92Electrical Safety

    Which statement about the equipment grounding conductor is correct?

    1. It may be omitted on 240-volt single-phase circuits
    2. It carries current during normal equipment operation
    3. It must provide a permanent, continuous path to the source Correct answer.
    4. It may be the same conductor as the circuit neutral

    Explanation

    The equipment grounding conductor must form a permanent and continuous path with ample capacity to carry fault current safely back to the source so that overcurrent devices operate. It is distinct from the grounded circuit conductor and normally carries no current. Omitting it defeats the fault-clearing path.

  93. Question 93Electrical Safety

    When employees use tools where contact with exposed energized parts is possible, the employer must provide...

    1. tools that are held with both hands
    2. insulated tools rated for the voltage involved Correct answer.
    3. tools grounded to the nearest metal raceway
    4. non-sparking tools for all voltage levels

    Explanation

    Insulated tools and handling equipment must be used when they might contact exposed energized conductors or parts, and the insulation must be suitable for the voltage involved. Damaged insulation must be replaced. Non-sparking and grounding rules address different hazards.

  94. Question 94Electrical Safety

    Under what circumstances may an electrical safety interlock be defeated?

    1. By any employee who tags the equipment with a warning
    2. Whenever the equipment is scheduled for maintenance
    3. When the interlock trips more than twice in a shift
    4. Temporarily, by a qualified person working on the equipment Correct answer.

    Explanation

    An interlock may be defeated only temporarily by a qualified person while the work on the equipment is being performed, and it must be restored to operable condition when that work is finished. Interlocks exist to prevent access to energized parts, so bypassing them requires both qualification and control.

  95. Question 95Electrical Safety

    What marking is required for each disconnecting means?

    1. The circuit's ampacity and wire size
    2. The date of the last electrical inspection
    3. Its purpose, unless the purpose is evident Correct answer.
    4. The name of the electrician who installed it

    Explanation

    Each disconnecting means must be legibly marked to show what it controls, unless its location and arrangement make the purpose obvious. This marking lets workers identify the correct device before opening it, reducing the chance of deenergizing the wrong circuit. The required marking is about purpose, not installation history.

  96. Question 96Electrical Safety

    Equipment must be kept clear of a 345 kV overhead line. Using the rule of 10 feet plus 0.4 inch for each kV above 50 kV, the minimum clearance is about...

    1. 20 feet Correct answer.
    2. 30 feet
    3. 14 feet
    4. 10 feet

    Explanation

    Subtract the 50 kV base from 345 kV to get 295 kV, multiply by 0.4 inch to get 118 inches, which is about 9.8 feet, and add the 10-foot base distance. The result is roughly 19.8 feet, so about 20 feet. The added distance grows with voltage because the arc can jump farther.

  97. Question 97Electrical Safety

    Portable ladders used where the ladder or the employee could contact exposed energized parts must...

    1. be inspected weekly by a qualified person
    2. be rated for at least 300 pounds
    3. be tied off at the top and bottom
    4. have nonconductive side rails Correct answer.

    Explanation

    Ladders used near exposed energized parts must have nonconductive side rails so the ladder does not become a path to ground or a bridge to another conductor. Tying off, inspection frequency, and load rating address fall protection and structural integrity, not electrical conductivity.

  98. Question 98Electrical Safety

    Who decides whether an employee is a qualified person for a given electrical task?

    1. The employee, based on years of experience in the trade
    2. The employer, based on training and demonstrated skill Correct answer.
    3. The local electrical inspector
    4. The manufacturer of the equipment being worked on

    Explanation

    Qualified status depends on the training the employee has received and the skills the employee has demonstrated, and the employer makes that determination for the specific task and voltage involved. Trade tenure alone does not establish qualification, and outside parties do not assign it.

  99. Question 99Electrical Safety

    Which practice is specifically prohibited when working near exposed energized parts?

    1. Using a voltage-rated meter to confirm a circuit is dead
    2. Working with a second qualified employee present
    3. Reaching blindly into an area that may contain live parts Correct answer.
    4. Using a fiberglass fish tape to pull conductors

    Explanation

    Employees must not reach blindly into areas that may contain energized parts, because contact cannot be avoided when the hazard has not been seen or identified. The area should be illuminated and the parts identified before work proceeds. The other listed practices are acceptable or required.

  100. Question 100Electrical Safety

    How must flexible cords be connected to devices and fittings?

    1. With wire nuts inside the fitting for extra security
    2. With the grounding conductor cut back to prevent contact
    3. With tape wrapped around the connector body
    4. With strain relief so pull is not transmitted to terminals Correct answer.

    Explanation

    Cords must be connected so that strain relief prevents pulling forces from being transmitted directly to joints or terminal screws, which could loosen conductors and create heat or arcing. The grounding conductor must remain continuous, and tape or wire nuts inside a fitting are not an acceptable substitute for proper cord connection.

  101. Question 101Personal Protective Equipment

    Under OSHA's general industry rules, eye and face protection must be provided whenever an employee is exposed to which condition?

    1. Flying particles, liquid chemicals, or injurious light Correct answer.
    2. Continuous noise levels that exceed 90 decibels on the A scale
    3. Walking surfaces that are oily or wet
    4. Confined spaces with an oxygen deficiency

    Explanation

    The eye and face protection standard requires protection wherever employees are exposed to flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation. The trigger is a hazard to the eyes or face, not general workplace conditions.

  102. Question 102Personal Protective Equipment

    Which class of hard hat is rated for contact with electrical conductors up to 20,000 volts?

    1. Class C
    2. Class E Correct answer.
    3. Class G
    4. Type II

    Explanation

    Under ANSI Z89.1, Class E (formerly Class B) helmets are proof-tested at 20,000 volts. Class G (formerly Class A) is rated to 2,200 volts, and Class C offers no electrical protection at all.

  103. Question 103Personal Protective Equipment

    A hearing conservation program must be established when employee noise exposure reaches or exceeds what level as an 8-hour time-weighted average?

    1. 85 dBA Correct answer.
    2. 80 dBA
    3. 90 dBA
    4. 100 dBA

    Explanation

    The noise standard requires a hearing conservation program, including monitoring, audiometric testing, and hearing protection availability, at an 85 dBA 8-hour time-weighted average. The 90 dBA level is the permissible exposure limit that triggers feasible engineering or administrative controls.

  104. Question 104Personal Protective Equipment

    Employees who use a tight-fitting respirator must be fit tested at which minimum frequency?

    1. At least once a year Correct answer.
    2. Every six months
    3. Only at initial hire
    4. Every two years

    Explanation

    The respiratory protection standard requires fit testing before initial use and at least annually thereafter. Additional fit testing is required whenever a different make, model, or size of respirator is used.

  105. Question 105Personal Protective Equipment

    Under OSHA's employer payment rule for PPE, which of the following must the employer pay for?

    1. Non-specialty safety-toe boots that may be worn off the site
    2. Everyday clothing suitable for the weather
    3. Ordinary prescription eyeglasses worn daily
    4. Replacement filter cartridges for a required respirator Correct answer.

    Explanation

    Employers must pay for required PPE, which includes respirator cartridges and other consumable or replacement components. The rule carves out exceptions for non-specialty safety-toe footwear and non-specialty prescription safety eyewear the employer allows to be worn off the job site, as well as everyday clothing and weather gear.

  106. Question 106Personal Protective Equipment

    After completing a workplace hazard assessment for PPE, what must the employer do in writing?

    1. Certify the assessment with workplace, certifier, and date Correct answer.
    2. Record the manufacturer's instructions for each item of PPE purchased
    3. Post the names of employees who received PPE training
    4. File copies of every PPE invoice with the safety office

    Explanation

    The hazard assessment must be certified in writing and must identify the workplace evaluated, the person certifying the evaluation, and the date of the assessment. This certification documents that the walkthrough occurred.

  107. Question 107Personal Protective Equipment

    An employer is choosing hand protection for workers who handle a solvent. What is the most appropriate basis for the selection?

    1. Whichever glove has the lowest purchase price in the worker's size
    2. A general-purpose cotton glove with a knit wrist
    3. The glove that the majority of the crew prefers to wear
    4. The glove's resistance to the specific solvent being handled Correct answer.

    Explanation

    Hand protection must be selected based on the performance characteristics of the glove relative to the hazards, conditions, and duration of the task. For chemical exposure, resistance to that specific substance is the controlling factor.

  108. Question 108Personal Protective Equipment

    An employee's personal fall arrest harness has been subjected to a fall arrest impact. What is required of the equipment?

    1. It may be reused if a visual inspection finds no fraying
    2. It may be reused only by a lighter worker
    3. It must be removed from service and not used again Correct answer.
    4. It may be reused after the impact indicator is reset

    Explanation

    Personal fall arrest equipment that has been subjected to fall arrest forces must be removed from service immediately. Energy absorbers and load-limiting components are single-use, and the manufacturer's removal criteria govern regardless of appearance.

  109. Question 109Personal Protective Equipment

    Safety-toe footwear is required where there is a danger of which type of injury?

    1. Falling or rolling objects that could crush the foot Correct answer.
    2. Static electricity buildup in carpeted offices
    3. Exposure to cold temperatures during outdoor winter work
    4. Slipping on wet, level concrete floors indoors

    Explanation

    Protective footwear is required where there is a danger of foot injuries from falling or rolling objects, from objects piercing the sole, or from electrical hazards. Crushing and puncture hazards are the classic triggers for safety-toe and metatarsal protection.

  110. Question 110Personal Protective Equipment

    Under ANSI/ISEA 107, which performance class provides the greatest visibility and is typically needed for workers exposed to high-speed traffic or low-light conditions?

    1. Performance Class 3 Correct answer.
    2. Performance Class 2
    3. Type O only
    4. Performance Class 1

    Explanation

    Class 3 garments carry the greatest amount of background and retroreflective material, often with sleeves or full-length trousers. They are specified for high-speed traffic, night work, and complex backgrounds, while Class 1 and Class 2 cover lower-risk exposures.

  111. Question 111Personal Protective Equipment

    Rubber insulating gloves used for electrical protection must be electrically tested at what maximum interval?

    1. Every 12 months
    2. Every 24 months
    3. Every 3 months
    4. Every 6 months Correct answer.

    Explanation

    Rubber insulating gloves must be tested before first issue and every six months thereafter. Rubber insulating sleeves follow a longer interval, being tested every 12 months.

  112. Question 112Personal Protective Equipment

    Before an employee is fit tested or required to use a respirator in the workplace, what must the employer do?

    1. Ensure the employee is medically evaluated Correct answer.
    2. Confirm the employee has corrected 20/20 vision
    3. Arrange a second medical opinion for every employee
    4. Obtain a signed respirator-use waiver from the employee

    Explanation

    The employer must provide a medical evaluation to determine whether the employee is able to use a respirator before fit testing or respirator use. A physician or other licensed health care professional reviews the questionnaire and clears the employee.

  113. Question 113Personal Protective Equipment

    Which situation requires the employer to retrain an employee on PPE use?

    1. The company hires a new safety manager
    2. Changes in the workplace make earlier training obsolete Correct answer.
    3. The employee has been late to work twice
    4. The employee asks to be issued a different color of hard hat

    Explanation

    Retraining is required when changes in the workplace or in the types of PPE used make prior training obsolete, when the employee shows a lack of understanding, or when the employee's behavior shows the training was not retained.

  114. Question 114Personal Protective Equipment

    A hard hat has sustained a significant impact from a falling object. What is the correct action?

    1. Keep using it if a visual inspection shows no cracks
    2. Replace it, because the shell may be weakened Correct answer.
    3. Sand the damaged area smooth and keep using it
    4. Keep using it until the next scheduled replacement date

    Explanation

    A hard hat that has taken a significant impact must be removed from service and replaced because the shell's ability to absorb and distribute energy can be compromised even without visible cracks.

  115. Question 115Personal Protective Equipment

    Where employees may be exposed to injurious corrosive materials, an eyewash facility should supply flushing fluid for at least how long?

    1. 15 minutes Correct answer.
    2. 30 minutes
    3. 5 minutes
    4. 10 minutes

    Explanation

    Emergency eyewash and shower equipment is designed to deliver a 15-minute supply of flushing fluid, reachable within about 10 seconds of travel. The standard requires suitable facilities wherever the eyes or body may be exposed to injurious corrosive materials.

  116. Question 116Personal Protective Equipment

    Which type of PPE is essential when arc welding to protect against intense light and sparks?

    1. A high-visibility vest
    2. A welding helmet with filter lens Correct answer.
    3. A face shield alone
    4. A dust mask

    Explanation

    Welding requires a helmet with an appropriate filter shade to protect the eyes and face from arc radiation, sparks, and spatter. A face shield alone does not filter the harmful ultraviolet and infrared radiation of the arc.

  117. Question 117Personal Protective Equipment

    An employee finds that a required respirator has a cracked lens and torn straps. What must happen?

    1. The employee tapes the crack and continues to wear it
    2. The defective equipment is removed and replaced Correct answer.
    3. The employee works the rest of the shift without protection
    4. The equipment stays in use until the end of the shift

    Explanation

    Defective or damaged PPE must not be used; it must be taken out of service and repaired or replaced before the employee continues the task. PPE must be maintained in a reliable condition at all times.

  118. Question 118Personal Protective Equipment

    An employee's 8-hour noise exposure is 100 dBA. A hearing protector has an NRR of 25. Using OSHA's Appendix B method for A-weighted exposures, the estimated exposure under the protector is:

    1. 100 dBA
    2. 82 dBA Correct answer.
    3. 93 dBA
    4. 75 dBA

    Explanation

    For A-weighted measurements, OSHA's method first subtracts 7 from the NRR (25 − 7 = 18) and then subtracts that value from the time-weighted average (100 − 18 = 82 dBA). The 7 dB adjustment accounts for the difference between the laboratory test and real-world use.

  119. Question 119Personal Protective Equipment

    A face shield is being used while mixing a liquid chemical that splashes. What additional protection is generally needed?

    1. No additional eye protection is needed with a face shield
    2. Safety goggles worn under the shield Correct answer.
    3. A dust mask worn under the shield
    4. A hard hat with a full brim

    Explanation

    Face shields protect the face but do not seal around the eyes, so splashes and flying particles can reach the eyes from the sides and below. Primary eye protection such as goggles must be worn with the shield.

  120. Question 120Personal Protective Equipment

    Entry into an atmosphere that is immediately dangerous to life or health (IDLH) requires which type of respiratory protection?

    1. A powered air-purifying respirator with HEPA filters
    2. A full facepiece pressure-demand SCBA Correct answer.
    3. A single N95 filtering facepiece
    4. A half-mask air-purifying respirator with cartridges

    Explanation

    Air-purifying respirators cannot be used in IDLH atmospheres because they do not supply breathable air and offer no escape capability. Atmosphere-supplying respirators, typically a full facepiece pressure-demand self-contained breathing apparatus, are required, along with a standby attendant.

  121. Question 121Personal Protective Equipment

    An employer permits workers to use their own personal protective equipment. What does OSHA require?

    1. The employee must sign a liability release form
    2. The equipment must be inspected by the manufacturer
    3. The employer must ensure it meets required standards Correct answer.
    4. The employer is free of responsibility for that equipment

    Explanation

    When employees provide their own PPE, the employer remains responsible for ensuring the equipment is adequate and properly maintained. The employer also must follow the payment rule for replacement PPE.

  122. Question 122Personal Protective Equipment

    Which type of PPE is appropriate for protecting the torso from chemical splashes?

    1. A high-visibility safety vest
    2. A back support belt
    3. Cut-resistant sleeves
    4. A chemical-resistant apron Correct answer.

    Explanation

    Body protection must be selected for the specific hazard; a chemical-resistant apron shields the torso and lap from liquid chemical contact. Cut-resistant sleeves and back belts address entirely different hazards.

  123. Question 123Personal Protective Equipment

    Head protection must be worn where there is a risk of which of the following?

    1. Objects falling from above onto the head Correct answer.
    2. Exposure to continuous noise levels above 85 dBA
    3. Walking on slippery floors
    4. Working in a wet or humid environment for long shifts

    Explanation

    Head protection is required where there is a potential for head injury from falling or flying objects, from bumping into fixed objects or equipment, or from electrical shock or burn. The governing question is whether the head can be struck or contacted hazardously.

  124. Question 124Personal Protective Equipment

    An employee who wears prescription glasses needs eye protection for grinding work. What is the acceptable solution?

    1. Wear protective eyewear that incorporates the prescription Correct answer.
    2. Wear the regular glasses alone because the lenses are impact resistant
    3. Remove the glasses and rely on a face shield for protection
    4. Wear a dust mask together with the regular glasses

    Explanation

    Employees whose vision requires corrective lenses must wear eye protection that incorporates the prescription into its design, or wear eye protection that fits over the prescription lenses without disturbing their alignment. Everyday dress glasses are not substitutes for protective eyewear.

  125. Question 125Personal Protective Equipment

    Reusable PPE must be kept in what condition between uses?

    1. Replaced at the start of each calendar year
    2. Cleaned only when it looks visibly dirty to the worker
    3. Stored in the employee's locker until it wears out
    4. Maintained in a sanitary and reliable condition Correct answer.

    Explanation

    All PPE must be maintained in a sanitary and reliable condition, which includes cleaning, inspecting, maintaining, and storing it properly. Damaged or contaminated equipment must be removed from service before reuse.

  126. Question 126Hazard Communication

    What is the primary purpose of OSHA's Hazard Communication Standard?

    1. To set permissible exposure limits for every chemical used in general industry
    2. To ban from general industry use any chemical that is known to cause cancer in animals
    3. To ensure chemical hazards are evaluated and information is communicated Correct answer.
    4. To require employers to buy only chemicals that carry a manufacturer's written warranty

    Explanation

    The standard requires chemical manufacturers and importers to evaluate the hazards of the chemicals they produce or import and to transmit that information downstream through labels and safety data sheets. Employers then pass the information to exposed employees through labels, SDSs, and training. It does not ban chemicals, set exposure limits, or regulate purchasing.

  127. Question 127Hazard Communication

    Under the Hazard Communication Standard, what must an employer with hazardous chemicals in the workplace do?

    1. Post the full text of 29 CFR 1910.1200 at every work station in the facility
    2. Submit a copy of the facility's chemical inventory to OSHA every year
    3. Develop, implement, and maintain a written hazard communication program at each workplace Correct answer.
    4. Obtain a permit before introducing any new chemical into the facility

    Explanation

    The employer must prepare and maintain a written program at each workplace that describes how labels, SDSs, and training will be handled, and must make the program available to employees. Posting the rule text, filing inventories with OSHA, and pre-approval permits are not requirements of the standard.

  128. Question 128Hazard Communication

    How many sections does a Safety Data Sheet contain under the current Hazard Communication Standard?

    1. 8
    2. 12
    3. 20
    4. 16 Correct answer.

    Explanation

    The standard requires a standardized 16-section SDS in a fixed order, beginning with identification and ending with other information. This uniform format lets users find hazard, first-aid, and handling information in the same place on every sheet.

  129. Question 129Hazard Communication

    Which two signal words are used on labels under the Hazard Communication Standard?

    1. Danger and Caution
    2. Caution and Notice
    3. Danger and Warning Correct answer.
    4. Warning and Caution

    Explanation

    Only the words Danger and Warning are recognized signal words; Danger indicates the more severe hazard category and Warning the less severe. Caution and Notice are not signal words under the standard, although they may appear in other labeling systems.

  130. Question 130Hazard Communication

    An employee sees a label pictogram showing liquid dripping from two test tubes onto a surface and a hand, with damage shown at both contact points. Which hazard does this pictogram represent?

    1. Compressed or liquefied gas
    2. Flammable liquids and solids
    3. Acute toxicity from a single exposure
    4. Corrosive to skin and eyes Correct answer.

    Explanation

    The corrosion pictogram shows material attacking skin and metal surfaces, and it signals skin corrosion or serious eye damage. Flammables, acute toxicity, and gases each have their own distinct pictograms.

  131. Question 131Hazard Communication

    A maintenance worker pours solvent from a labeled 55-gallon drum into a spray bottle and will use it during the same shift. What does the standard require for the spray bottle?

    1. It must be labeled unless used immediately by the employee who filled it Correct answer.
    2. No label is required because the container holds only a small amount
    3. Only an NFPA 704 diamond must be applied to the container
    4. It must carry the original manufacturer's label with all pictograms

    Explanation

    Portable containers used by one employee for immediate use during the same shift are exempt from labeling. Once the material is transferred to another worker, stored, or used beyond that immediate period, a workplace label with the product identifier and hazard information is required.

  132. Question 132Hazard Communication

    Which section of a Safety Data Sheet provides exposure limits, engineering controls, and personal protective equipment guidance?

    1. Section 4
    2. Section 14
    3. Section 2
    4. Section 8 Correct answer.

    Explanation

    Section 8, Exposure Controls/Personal Protection, lists exposure limits and the engineering controls and protective equipment needed for safe work. Section 2 covers hazard identification, Section 4 covers first-aid measures, and Section 14 covers transport information.

  133. Question 133Hazard Communication

    Which SDS section identifies the chemical ingredients, including impurities and stabilizing additives, along with concentration ranges where applicable?

    1. Section 13 - Disposal considerations
    2. Section 3 - Composition/information on ingredients Correct answer.
    3. Section 1 - Identification
    4. Section 9 - Physical and chemical properties

    Explanation

    Section 3 lists the chemical identity of ingredients and, where applicable, concentration ranges, subject to trade secret protections. Section 1 identifies the product and supplier, Section 9 covers physical properties, and Section 13 covers disposal.

  134. Question 134Hazard Communication

    A new employee is hired into a job that involves handling hazardous chemicals. When must hazard communication training be provided?

    1. Before the employee begins work with the chemical Correct answer.
    2. Whenever the employer schedules the next annual safety meeting
    3. Only after an injury involving a chemical exposure occurs
    4. Within 30 days after the employee's first day on the job

    Explanation

    Training must be given at the time of initial assignment and whenever a new hazard is introduced into the work area. It cannot be deferred to a probation period, an annual meeting, or an incident.

  135. Question 135Hazard Communication

    An employer claims trade secret protection for a chemical identity on a Safety Data Sheet. What must still be provided to workers?

    1. Hazard information for safe handling, with identity released only under specified conditions Correct answer.
    2. The chemical identity written in full on the label but not on the SDS
    3. Nothing; trade secret status removes all disclosure obligations for that chemical
    4. A copy of the manufacturer's trade secret registration filed with OSHA

    Explanation

    Trade secret protection limits disclosure of the specific chemical identity, but the hazardous properties and safe-handling information must still be provided. The identity must be released under specified conditions, such as to a health professional evaluating an exposure or under a confidentiality agreement.

  136. Question 136Hazard Communication

    A chemical manufacturer learns of a significant new hazard for a product already in commerce. Within what period must the Safety Data Sheet be revised?

    1. Only at the next scheduled annual revision
    2. Immediately, within 24 hours
    3. Within three months Correct answer.
    4. Within 30 days

    Explanation

    When a manufacturer, importer, or employer becomes aware of significant new information about a chemical's hazards, the SDS must be updated within three months. Labels must also be updated with the new information.

  137. Question 137Hazard Communication

    How must pipes and piping systems that carry hazardous chemicals be identified?

    1. Only when a contractor is working on the site
    2. Only if the pipe crosses a walkway used by employees
    3. Never, because piping is exempt from the labeling requirements
    4. Labeled with the contents' identity and appropriate hazard warnings Correct answer.

    Explanation

    The employer must ensure that pipes and piping systems are labeled with the identity of the hazardous chemical and appropriate hazard warnings. Piping is not exempt, and signage for contractors does not substitute for routine identification.

  138. Question 138Hazard Communication

    A facility marks containers with NFPA 704 diamonds. How does this practice relate to the Hazard Communication Standard?

    1. NFPA diamonds are an acceptable substitute for HCS labels on shipped containers
    2. HCS forbids the use of any non-GHS hazard marking on workplace containers
    3. NFPA ratings satisfy HCS training obligations without additional labels
    4. NFPA markings may supplement but not replace HCS-compliant labels Correct answer.

    Explanation

    NFPA and HMIS systems lack required HCS elements such as hazard statements, precautionary statements, and GHS pictograms, so they cannot take the place of a compliant label. They may be added alongside HCS labels as an internal aid.

  139. Question 139Hazard Communication

    Employees periodically enter and clean a tank that can accumulate hydrogen sulfide. What does the standard require for this task?

    1. Issuing respirators and relying on prior general training
    2. Training on the specific hazards and needed protections Correct answer.
    3. Posting the SDS outside the tank entry point
    4. Providing a copy of the written program after the task

    Explanation

    Workers assigned non-routine tasks with hazardous chemicals must be trained on the specific hazards of the task and the protections to be used before performing the work. Posting an SDS or supplying equipment does not substitute for task-specific training.

  140. Question 140Hazard Communication

    Which of the following is excluded from the definition of "hazardous chemical" under the Hazard Communication Standard?

    1. A sealed 55-gallon drum of industrial solvent stored outdoors
    2. Combustible dust generated by a machining operation
    3. Aerosol cans of spray adhesive sold in retail stores to consumers
    4. An article that releases no hazardous chemical in normal use Correct answer.

    Explanation

    An article is a manufactured item that does not release more than very small quantities of a hazardous chemical under normal conditions of use, and articles are excluded from the definition. Sealed drums, aerosol products, and combustible dusts are all within scope.

  141. Question 141Hazard Communication

    OSHA enforces most Safety Data Sheet content requirements, but which sections of the SDS are not enforced by OSHA?

    1. Sections 1 through 3
    2. Sections 9 through 11
    3. Sections 12 through 15 Correct answer.
    4. Sections 4 through 8

    Explanation

    Sections 12 through 15 cover ecological information, disposal considerations, transport information, and regulatory information, which fall outside OSHA's authority. OSHA still requires that these sections appear in the 16-section format, but does not enforce their content.

  142. Question 142Hazard Communication

    A host employer brings contractor personnel into a plant where hazardous chemicals are used. What does the Hazard Communication Standard require?

    1. Hazard information and site labeling for employees of other employers Correct answer.
    2. The host employer must send copies of SDSs to OSHA but not to contractors
    3. Responsibility transfers entirely to the contractor once the contractor enters the site
    4. Contractors must independently obtain all SDSs from the chemical manufacturers

    Explanation

    In multi-employer workplaces, the host employer must ensure that employees of other employers on site receive information about the hazardous chemicals they may be exposed to and about the site's labeling system and SDS availability. Responsibility is shared, not transferred.

  143. Question 143Hazard Communication

    In which situation does a consumer product used at a workplace fall under the labeling and SDS requirements of the Hazard Communication Standard?

    1. When the product is sold in containers smaller than one gallon
    2. When employee exposure greatly exceeds normal consumer duration or frequency Correct answer.
    3. When the employer purchased the product from a distributor rather than a retailer
    4. When the product is stored in a room with other hazardous chemicals

    Explanation

    The consumer-product exemption applies only when the product is used in the manner intended by the manufacturer and results in exposures no greater than a consumer could reasonably experience. If duration or frequency of exposure exceeds that range, the product is covered and must be labeled and supported by an SDS.

  144. Question 144Hazard Communication

    Which hazard is represented by the skull and crossbones pictogram on an HCS label?

    1. Acute toxicity, fatal or toxic Correct answer.
    2. Oxidizing gases and liquids
    3. Skin sensitization
    4. Flammable liquids and solids

    Explanation

    The skull and crossbones pictogram signals acute toxicity, meaning a chemical that can cause death or serious harm after a single or short-term exposure. Flammables use the flame pictogram, oxidizers use the flame over circle, and sensitizers use the exclamation mark or health hazard pictogram.

  145. Question 145Hazard Communication

    Under the Hazard Communication Standard, who is responsible for providing Safety Data Sheets to the employer?

    1. OSHA's regional office
    2. The chemical manufacturer or importer Correct answer.
    3. The employees' union representative
    4. The employer's joint safety and health committee

    Explanation

    Manufacturers and importers must obtain or develop an SDS for each hazardous chemical and provide it with the initial shipment and with the first shipment after an update. The employer then makes those SDSs accessible to employees.

  146. Question 146Hazard Communication

    In what manner must hazard communication training be delivered?

    1. Only by a certified industrial hygienist
    2. Only in English, because the standard is a federal regulation
    3. Only in writing, with each employee's signature on file
    4. In a manner and language employees can understand Correct answer.

    Explanation

    Training must be provided at the time of initial assignment and whenever a new hazard is introduced, and it must be presented in a manner and language that employees can understand. Written materials alone or a specific outside credential are not required by the rule.

  147. Question 147Hazard Communication

    What access to Safety Data Sheets must an employer give to employees?

    1. At any time during their shift in their work area Correct answer.
    2. Only after a written request to the plant manager is approved
    3. Only during scheduled safety meetings held each quarter
    4. Only when an employee's physician submits a request

    Explanation

    Employees must be able to access SDSs for the hazardous chemicals in their work area at any time they are in that area during their shift, without having to request permission. Electronic access is acceptable if no barriers prevent immediate use and a backup is available.

  148. Question 148Hazard Communication

    What is a precautionary statement on an HCS label?

    1. A standardized phrase describing the nature of the hazard
    2. A word such as Danger or Warning that indicates hazard severity
    3. A code identifying the manufacturer's product number
    4. Recommended measures to minimize or prevent adverse effects Correct answer.

    Explanation

    Precautionary statements describe handling and protective measures, such as wearing gloves or keeping containers closed, that reduce the risk of adverse effects. Signal words indicate severity and hazard statements describe the nature of the hazard.

  149. Question 149Hazard Communication

    Which item must be included in the employer's written hazard communication program?

    1. The names and telephone numbers of each employee's personal physician
    2. A floor plan showing the location of each eyewash and shower station
    3. The date of each employee's most recent medical examination and its results
    4. A list of hazardous chemicals using the same identifiers as labels Correct answer.

    Explanation

    The written program must include a list of the hazardous chemicals known to be present, identified by the product identifier used on the label and the SDS. Medical records and emergency-equipment floor plans belong to other requirements, not to the hazard communication program.

  150. Question 150Hazard Communication

    Which of the following is classified as a physical hazard under the Hazard Communication Standard?

    1. Carcinogen
    2. Reproductive toxin
    3. Respiratory sensitizer
    4. Flammable aerosol Correct answer.

    Explanation

    Physical hazards include flammables, explosives, oxidizers, compressed gases, and corrosives to metal, because they concern the chemical's properties and behavior. Carcinogenicity, reproductive toxicity, and respiratory sensitization are health hazards.

  151. Question 151Materials Handling, Storage, Use, and Disposal

    How must permanent aisles and passageways be treated in a storage area?

    1. They must be at least 12 feet wide at every point.
    2. They must be re-striped by a supervisor each month.
    3. They must be appropriately marked. Correct answer.
    4. They must be surfaced with a non-skid coating.

    Explanation

    OSHA's storage and handling rules require that permanent aisles and passageways be appropriately marked so that travel lanes stay identifiable. The standard does not set a universal numeric width and does not prescribe re-striping schedules.

  152. Question 152Materials Handling, Storage, Use, and Disposal

    Where mechanical handling equipment is used, what must be provided for aisles, at loading docks, through doorways, and wherever turns or passage must be made?

    1. A raised curb along each travel route.
    2. A trained spotter stationed at every doorway.
    3. Sufficient safe clearances. Correct answer.
    4. A posted speed limit of 5 miles per hour.

    Explanation

    The mechanical handling provision requires enough safe clearance for equipment at aisles, loading docks, doorways, and turning points. Aisles must also be kept clear, in good repair, and free of obstructions.

  153. Question 153Materials Handling, Storage, Use, and Disposal

    Under OSHA's powered industrial truck standard, how often must a truck be examined?

    1. Before being placed in service, and daily thereafter. Correct answer.
    2. Only after a reported incident or near miss.
    3. Once a month by the safety committee.
    4. Once a week by a maintenance technician during scheduled downtime.

    Explanation

    Powered industrial trucks must be examined before being placed in service and at least daily after that; trucks used around the clock must be examined after each shift. Defects found must be corrected before the truck is returned to use.

  154. Question 154Materials Handling, Storage, Use, and Disposal

    Which of these is permitted under OSHA's rules for powered industrial trucks?

    1. Carrying a second employee on the load being lifted.
    2. Carrying a passenger in a seat designed for that purpose. Correct answer.
    3. Allowing a trained employee to stand on the forks.
    4. Letting a coworker ride briefly on the truck's counterweight for a short trip.

    Explanation

    Riders are allowed only where a safe place to ride is provided, meaning a seat or compartment designed for a passenger. Standing on forks or riding on the load or counterweight is prohibited. Elevating a person requires a securely attached platform, not bare forks.

  155. Question 155Materials Handling, Storage, Use, and Disposal

    How often, and by whom, must slings and their attachments be inspected?

    1. Each day before use, by a competent person. Correct answer.
    2. Each week, by the tool room attendant.
    3. Each month, by the manufacturer's representative.
    4. Each year, by an outside inspection agency.

    Explanation

    Slings and all fastenings and attachments must be inspected each day before use by a competent person designated by the employer. Damaged or defective slings must be removed from service.

  156. Question 156Materials Handling, Storage, Use, and Disposal

    Why does OSHA require clearance signs in storage areas?

    1. To warn employees of overhead clearance limits. Correct answer.
    2. To identify the maximum permissible floor loading for each level of racking.
    3. To mark the location of fire extinguishers.
    4. To show the rated capacity of the storage racks.

    Explanation

    The clearance limits provision requires clearance signs that warn employees of overhead clearance limits, protecting them from striking structures or equipment.

  157. Question 157Materials Handling, Storage, Use, and Disposal

    If the load on a forklift blocks the operator's forward view, the operator must:

    1. Raise the load until it clears the operator's line of sight.
    2. Increase speed to shorten the time the view is blocked.
    3. Ask a coworker to walk ahead and guide the truck.
    4. Travel in reverse with the load trailing. Correct answer.

    Explanation

    When a load obstructs forward visibility, the operator must travel in reverse with the load trailing. Raising the load or speeding up increases the hazard rather than removing it.

  158. Question 158Materials Handling, Storage, Use, and Disposal

    Storage areas must be kept free of accumulated materials that create hazards from:

    1. tripping and slipping hazards only.
    2. insect and rodent harborage only.
    3. tripping, fire, explosion, or pests. Correct answer.
    4. fire and explosion hazards only.

    Explanation

    The secure storage provision requires storage areas to be kept free of accumulations that create hazards from tripping, fire, explosion, or pest harborage. Vegetation control is required where necessary. The rule addresses all of these hazards together, not one at a time.

  159. Question 159Materials Handling, Storage, Use, and Disposal

    Which practice is prohibited when rigging a load with slings?

    1. Tying knots in a sling to shorten it. Correct answer.
    2. Using a sling whose rating exceeds the load weight.
    3. Protecting slings from sharp corners with softeners.
    4. Balancing the load before the lift begins.

    Explanation

    Slings must not be shortened with knots, bolts, or other makeshift devices because knots sharply reduce strength and can slip. Using corner protection, selecting adequate capacity, and balancing the load are all accepted rigging practices.

  160. Question 160Materials Handling, Storage, Use, and Disposal

    OSHA requires refresher training for a forklift operator when:

    1. the operator receives a promotion or pay raise.
    2. the operator moves to a different shift or department.
    3. the operator is observed operating unsafely. Correct answer.
    4. the operator has been employed for more than five years.

    Explanation

    Refresher training is triggered by unsafe operation, an accident or near miss, an evaluation showing deficiencies, or a change in the workplace or truck that affects safe operation. Seniority, pay, and shift changes alone do not trigger it.

  161. Question 161Materials Handling, Storage, Use, and Disposal

    At cross aisles and other locations where vision is obstructed, the forklift operator must:

    1. come to a full stop and wait for a spotter.
    2. switch on the hazard lights and keep the normal speed.
    3. slow down and sound the horn. Correct answer.
    4. sound the horn only when another truck is in sight.

    Explanation

    Operators must slow down and sound the horn at cross aisles and wherever vision is obstructed. The warning is given whether or not another truck is currently visible.

  162. Question 162Materials Handling, Storage, Use, and Disposal

    For OSHA's purposes, a powered industrial truck is unattended when the operator is:

    1. more than 15 feet away from the truck.
    2. 25 feet or more away, or the truck is out of the operator's view. Correct answer.
    3. out of the building in which the truck is parked and stored for the shift.
    4. more than 10 feet away from the truck.

    Explanation

    A truck counts as unattended when the operator is 25 feet or more away and the truck remains in view, or whenever the operator leaves it and it is not in view. Unattended trucks must have the load-engaging means lowered, controls neutralized, power off, and brakes set.

  163. Question 163Materials Handling, Storage, Use, and Disposal

    Before a forklift is driven into a railroad car or trailer, the employer must make sure that:

    1. the car's or trailer's brakes are set and its wheels are chocked. Correct answer.
    2. the dock lights are turned off to reduce glare.
    3. a second employee is watching from the dock.
    4. the roof and sides of the trailer have been inspected for leaks and damage.

    Explanation

    Railroad cars and trailers must be secured against movement before a truck is driven into them, which means brakes set and wheels chocked. This prevents the trailer or car from shifting or creeping away from the dock.

  164. Question 164Materials Handling, Storage, Use, and Disposal

    Alloy steel chain slings must be marked with:

    1. the name of the person who rigged the last load.
    2. a color code matching the capacity plate on the crane in use.
    3. a durable tag showing size, grade, and rated capacity. Correct answer.
    4. the date of the most recent monthly inspection.

    Explanation

    Chain slings must carry durable identification showing size, grade, rated capacity, and reach. The tag lets riggers confirm capacity before lifting.

  165. Question 165Materials Handling, Storage, Use, and Disposal

    What is the maximum number of randomly distributed broken wires in one lay that a wire rope sling may have before it is removed from service?

    1. 15
    2. 10 Correct answer.
    3. 20
    4. 25

    Explanation

    A wire rope sling is removed from service when there are 10 randomly distributed broken wires in one lay, or 5 broken wires in one strand in one lay. These thresholds are lower when the broken wires concentrate in a single strand.

  166. Question 166Materials Handling, Storage, Use, and Disposal

    Which facilities must be provided at a battery charging installation?

    1. Flushing and neutralizing means, fire protection, and ventilation. Correct answer.
    2. An eyewash station in a separate building from the chargers.
    3. A fire blanket, a covered sand bucket, and a Class D extinguisher at each charger.
    4. An exhaust fan rated for combustible dust and a ground strap.

    Explanation

    Battery charging areas must have facilities for flushing and neutralizing spilled electrolyte, fire protection, protection of charging apparatus from truck damage, and adequate ventilation for hydrogen gas.

  167. Question 167Materials Handling, Storage, Use, and Disposal

    A powered industrial truck found to be in need of repair must be:

    1. operated at reduced speed until the end of the week.
    2. repaired by the operator at the end of the shift.
    3. left in place and used only for light loads.
    4. taken out of service until the repair is made. Correct answer.

    Explanation

    Trucks needing repair or in any way defective must be taken out of service until restored to safe operating condition. Repairs must be made by authorized personnel.

  168. Question 168Materials Handling, Storage, Use, and Disposal

    On spur railroad tracks where a rolling car could strike other cars or enter a building, OSHA requires:

    1. a six-foot fence along both sides of the track.
    2. a switch tender on duty during all shifts.
    3. a flashing warning light at the track entrance.
    4. derail devices or bumper blocks. Correct answer.

    Explanation

    The rolling railroad car provision requires derail devices and/or bumper blocks where a rolling car could contact cars being worked or enter a building, work area, or traffic area.

  169. Question 169Materials Handling, Storage, Use, and Disposal

    Which practice meets OSHA's load handling requirements for powered industrial trucks?

    1. Adding counterweight at the rear to raise the capacity.
    2. Handling only stable loads that are within the rated capacity. Correct answer.
    3. Carrying a slightly overloaded load if it is kept low.
    4. Tilting the load forward to shift weight onto the drive wheels.

    Explanation

    Trucks may handle only stable or safely arranged loads, and the load must stay within the truck's rated capacity as shown on its nameplate. Capacity cannot be increased by improvised counterweighting.

  170. Question 170Materials Handling, Storage, Use, and Disposal

    Open pits, tanks, vats, and ditches in a storage area must be:

    1. covered or guarded with guardrails. Correct answer.
    2. filled with sand before materials are stored nearby.
    3. fenced at least 10 feet back from the edge.
    4. marked with yellow paint along the edge.

    Explanation

    The guarding provision requires covers and/or guardrails to protect personnel from open pits, tanks, vats, and ditches. Paint markings alone do not prevent a fall.

  171. Question 171Materials Handling, Storage, Use, and Disposal

    Under OSHA's training requirements, a trainee may operate a powered industrial truck:

    1. only after passing a written test on truck safety.
    2. only while wearing a high-visibility vest and hard hat.
    3. only in areas where no pedestrians are present.
    4. only under the direct supervision of a trainer. Correct answer.

    Explanation

    Trainees may operate a truck only under the direct supervision of a trainer, and never in a manner that endangers the trainee or other employees. Written tests and personal protective equipment do not substitute for supervision.

  172. Question 172Materials Handling, Storage, Use, and Disposal

    After initial training, a powered industrial truck operator's performance must be evaluated at least:

    1. once every three years. Correct answer.
    2. once every five years.
    3. every six months.
    4. whenever a new truck model is introduced.

    Explanation

    Operator performance evaluations must be conducted as part of initial training and at least once every three years afterward. Refresher training can occur sooner when unsafe operation or an incident indicates a need.

  173. Question 173Materials Handling, Storage, Use, and Disposal

    Which condition requires a synthetic web sling to be removed from service?

    1. The identification tag lists a capacity above the load.
    2. The webbing has snags, tears, or burns from heat or chemicals. Correct answer.
    3. The sling was last inspected more than 24 hours ago.
    4. The web is a different color from other slings on the rack.

    Explanation

    Synthetic web slings are removed from service for snags, punctures, tears, cuts, broken or worn stitches, distorted fittings, or burns and discoloration from heat or chemical contact. Color and tag capacity are not removal criteria.

  174. Question 174Materials Handling, Storage, Use, and Disposal

    Adding an attachment that affects a forklift's capacity requires:

    1. a 30-day trial period to confirm that it works.
    2. the manufacturer's prior written approval. Correct answer.
    3. approval by the site safety committee.
    4. notification of the shift supervisor only.

    Explanation

    Trucks must not be modified, and no additions affecting capacity and safe operation may be made, without the manufacturer's prior written approval. The truck's capacity may need a new nameplate reflecting the attachment.

  175. Question 175Materials Handling, Storage, Use, and Disposal

    What does OSHA require regarding the height of stacked materials?

    1. A fixed limit of 6 feet for all stored goods.
    2. A height limited so the stack stays stable and secure. Correct answer.
    3. A fixed limit of 12 feet for cartons on upper levels.
    4. The maximum stacking height printed on the carton by its maker.

    Explanation

    The standard sets no single numeric height; materials stored in tiers must be stacked, blocked, and interlocked, and the height must be limited so stacks stay stable and secure against sliding or collapse. Stability, not a fixed number, controls.

  176. Question 176Machine Guarding

    Under OSHA's machine guarding rules, what does the term 'point of operation' mean?

    1. The location where the finished product leaves the machine
    2. The location where power is transmitted from the motor to the machine's gears
    3. The area where the machine's start and stop controls are mounted
    4. The area on the machine where the work is actually performed on the material Correct answer.

    Explanation

    OSHA defines the point of operation as the area on the machine where the work is actually performed upon the material being processed. Because the operator's hands are closest to the moving tool at this location, it is the primary area requiring safeguarding.

  177. Question 177Machine Guarding

    According to 29 CFR 1910.212(a)(1), machine guarding must protect employees from which set of hazards?

    1. Only hazards that occur during machine setup and maintenance
    2. Hazards at the point of operation, ingoing nip points, rotating parts, and flying chips and sparks Correct answer.
    3. Only the hazard created at the point of operation
    4. Only hazards created by electrical components

    Explanation

    The general machine guarding standard lists the hazards to be addressed as those created by the point of operation, ingoing nip points, rotating parts, and flying chips and sparks. Guards must address all of these exposure types, not just the cutting or pressing point.

  178. Question 178Machine Guarding

    How must a machine guard be positioned or secured?

    1. Attached by a chain to the machine so it can be swung aside during operation
    2. Held in place by the operator's hands while the machine is running
    3. Attached to the floor or nearest wall rather than to the machine itself
    4. Affixed to the machine where possible Correct answer.

    Explanation

    Guards must be affixed to the machine whenever possible, and secured elsewhere only when attachment to the machine is not feasible. A guard the operator can swing aside or hold by hand does not provide reliable protection.

  179. Question 179Machine Guarding

    What is the maximum allowable gap between an abrasive wheel and its work rest?

    1. 1/2 inch
    2. 1/4 inch
    3. 1 inch
    4. 1/8 inch Correct answer.

    Explanation

    The work rest must be kept adjusted so the gap between the rest and the wheel face never exceeds one-eighth inch. A larger gap allows work to catch or be drawn into the wheel.

  180. Question 180Machine Guarding

    The adjustable tongue guard on an abrasive wheel grinder must be kept how far from the wheel face?

    1. 3/8 inch
    2. 1/4 inch Correct answer.
    3. 1/16 inch
    4. 1/8 inch

    Explanation

    The tongue guard is adjusted so the distance to the wheel face never exceeds one-quarter inch, and it must be readjusted as the wheel wears down. This limits the opening at the top of the wheel where fragments can escape.

  181. Question 181Machine Guarding

    How must a machine designed for a fixed location be secured?

    1. Securely anchored to prevent walking or moving Correct answer.
    2. Bolted down only when the manufacturer's manual requires it
    3. Restrained only by its own weight and the friction of its feet
    4. Mounted on a mobile base so it can be repositioned during shifts

    Explanation

    The standard requires machines designed for a fixed location to be securely anchored to prevent walking or moving. A machine that shifts during operation can create nip points and unexpected movement hazards.

  182. Question 182Machine Guarding

    Besides preventing contact with the hazard, what additional requirement applies to the design of a machine guard?

    1. It must not create an accident hazard in itself, such as a shear point or pinch point Correct answer.
    2. It must be painted a warning color on all sides
    3. It must be made of metal rather than plastic
    4. It must block the operator's view of the point of operation

    Explanation

    Guards must not offer an accident hazard in themselves, such as a shear point, pinch point, or sharp edge. A guard that injures employees creates a new exposure rather than eliminating one.

  183. Question 183Machine Guarding

    Before an abrasive wheel is mounted on a grinding machine, what inspection step is required?

    1. A ring test to confirm the wheel is not cracked Correct answer.
    2. A visual check with the wheel installed and running
    3. A dye-penetrant test performed by a certified inspector
    4. A balance check performed at operating speed

    Explanation

    Immediately before mounting, each wheel must be closely inspected and sounded by the user, commonly called the ring test, to detect damage or cracks. A damaged wheel can burst at operating speed and cause serious injury.

  184. Question 184Machine Guarding

    A horizontal drive belt runs between two pulleys with its lowest point five feet above the plant floor in a walking area. What does 29 CFR 1910.219 require?

    1. Only a warning sign posted beneath the belt
    2. Guarding only if the belt is wider than two inches
    3. The belt and pulleys must be guarded because they are less than seven feet above the floor Correct answer.
    4. Nothing, because the belt is above waist height

    Explanation

    Power transmission apparatus located seven feet or less above the floor or working platform must be guarded. At five feet, the belt and pulleys are within reach and require guarding.

  185. Question 185Machine Guarding

    Exposed gears on a machine are located where employees could be caught in them. Which method satisfies the guarding requirement?

    1. Training operators to keep their hands away from the gears
    2. Painting the gear teeth a bright warning color
    3. An enclosure that completely covers the gears Correct answer.
    4. Posting a warning sign next to the gear train

    Explanation

    Gears must be protected by a physical guard that prevents contact, and a complete enclosure is the standard approach for a gear train. Warnings and training do not remove the physical hazard.

  186. Question 186Machine Guarding

    Projecting shaft ends on rotating machinery must be:

    1. Covered by a slip-on plastic cap held in place by friction alone
    2. Shortened so that they do not extend beyond the bearing housing or frame
    3. Painted with a high-visibility stripe along their full length and inspected weekly
    4. Smooth and rounded or chamfered, with no projecting key or set screw Correct answer.

    Explanation

    Exposed shaft ends must be smooth and rounded or chamfered, and projecting keys, set screws, or pins are prohibited because they can catch clothing. Loose caps are not adequate because they can be knocked off.

  187. Question 187Machine Guarding

    A hand-fed ripsaw must be equipped with which combination of devices?

    1. A spreader, a hood guard, and an anti-kickback device Correct answer.
    2. A zero-clearance insert, a push stick, and a fence lock
    3. A blade brake, a magnetic starter, and a limit switch
    4. A riving knife, a featherboard, and a hold-down roller

    Explanation

    Hand-fed ripsaws require a hood guard enclosing the portion of the blade above the table and material, a spreader to keep the kerf open, and anti-kickback fingers. Together these control exposure to the blade and prevent stock from being thrown back.

  188. Question 188Machine Guarding

    After an operator completes a cut on a radial saw, what must the cutting head do?

    1. Lock in the forward position for the next pass
    2. Drop below the table surface to protect the blade
    3. Return automatically to its starting position behind the fence Correct answer.
    4. Remain where the operator left it until the next cut

    Explanation

    Radial saws must be arranged so the cutting head returns automatically to its starting position when released, keeping the blade behind the fence and away from the operator. The upper and lower blade portions must also be guarded.

  189. Question 189Machine Guarding

    How must the wheels and blade of a band saw be guarded?

    1. By a rail set twelve inches from the wheels
    2. By complete enclosures, with the blade guarded except at the point of operation Correct answer.
    3. By a guard that covers the entire blade at all times
    4. Only the upper wheel needs guarding

    Explanation

    Band saw wheels must be fully enclosed, and the blade must be guarded for its entire length except for the working portion at the point of operation. This prevents contact with the blade and with the rotating wheels.

  190. Question 190Machine Guarding

    Two-hand controls used on a mechanical power press must include which feature?

    1. An anti-repeat feature so the press cannot stroke again while the controls are held Correct answer.
    2. A key switch that converts the press to continuous operation
    3. A timer that releases the press cycle after five seconds
    4. A foot pedal that overrides the hand controls

    Explanation

    Two-hand controls must be designed so the press cannot stroke again until both controls are released and re-actuated, which prevents the operator from being trapped in a repeat cycle. Both hands are kept occupied and away from the point of operation during the stroke.

  191. Question 191Machine Guarding

    How does a restraint device differ from a pull-out device on a mechanical power press?

    1. One keeps the operator's hands away from the die, while the other pulls them away as the slide moves Correct answer.
    2. One interrupts a light curtain and the other stops the slide
    3. One requires lockout and the other requires a brake monitor
    4. One is used on press brakes and the other on hydraulic presses

    Explanation

    A restraint device physically limits how far the operator's hands can travel toward the die, while a pull-out device is attached to the hands or wrists and pulls them clear as the slide descends. Both are point-of-operation safeguarding methods recognized for presses.

  192. Question 192Machine Guarding

    In addition to the wheel itself, what must a grinding wheel guard cover?

    1. The work rest and the adjustable tongue
    2. The coolant nozzle and the wheel dresser
    3. The electrical conduit feeding the motor
    4. The spindle end, the spindle nut, and the flange projections Correct answer.

    Explanation

    The guard must enclose the spindle end, nut, and flange projections as well as the wheel, because these rotating parts can catch clothing or eject fragments. The guard must also be strong enough to contain a bursting wheel.

  193. Question 193Machine Guarding

    A millwright will remove a fixed guard to replace a drive belt on a conveyor. What must be done first?

    1. Notify the shift supervisor and post a warning sign on the control panel
    2. Isolate the machine from all energy sources and apply lockout/tagout Correct answer.
    3. Press the emergency stop and wait thirty seconds
    4. Reduce the conveyor to its slowest speed and use a spotter

    Explanation

    Removing a guard to reach a hazardous area is servicing that exposes employees to unexpected energization, so the machine must be isolated from all energy sources and locked out. The guard must then be reinstalled and secured before the equipment is returned to service.

  194. Question 194Machine Guarding

    What guarding must a portable circular saw have?

    1. A lower guard that returns automatically to the closed position Correct answer.
    2. A dead-man throttle that must be squeezed to run
    3. A riving knife welded permanently in place
    4. A chain brake that stops the blade on release

    Explanation

    Portable circular saws require guards above and below the base plate, and the lower guard must automatically and instantly return to the covering position when the saw is withdrawn from the work. This protects the operator between cuts.

  195. Question 195Machine Guarding

    Material jams inside a mixer, and an employee must clear it by hand. Which approach meets OSHA requirements?

    1. Open the inspection hatch and clear the jam before the mixer fully stops
    2. Ask a coworker to hold the safety switch closed while the mixer runs during clearing
    3. Reach in quickly while the mixer is running, using a gloved hand
    4. Shut down and lock out the energy source, then clear the jam with a tool Correct answer.

    Explanation

    Clearing a jam requires entry into a hazardous area, so the equipment must be de-energized and locked out first, and a tool should be used instead of hands. Bypassing interlocks or working during rundown exposes the employee to unexpected startup and stored motion.

  196. Question 196Machine Guarding

    Under 29 CFR 1910.217, periodic and regular inspections of mechanical power presses and their safeguarding equipment must be performed at intervals not exceeding:

    1. One week
    2. Five years
    3. Three years
    4. One year Correct answer.

    Explanation

    The employer must establish a program of periodic and regular inspections of presses, their guards, and their safeguards at intervals not exceeding one year. The specific interval within that limit is set by the manufacturer's recommendations and the severity of use.

  197. Question 197Machine Guarding

    The flanges used to mount an abrasive wheel must be at least what size relative to the wheel?

    1. One-quarter of the wheel's diameter
    2. One-half of the wheel's diameter
    3. The same diameter as the wheel's mounting hole
    4. One-third of the wheel's diameter Correct answer.

    Explanation

    Flanges must be at least one-third of the wheel diameter and matched in size and shape, so that clamping pressure is distributed and the wheel is not cracked at the arbor hole. Undersized flanges concentrate stress and can cause the wheel to break apart.

  198. Question 198Machine Guarding

    When designing a fixed barrier guard, what determines the minimum distance the guard must be placed from the point of operation?

    1. The color and visibility of the guard
    2. The weight of the guard and its mounting brackets
    3. The size of the openings in the guard Correct answer.
    4. The number of shifts the machine operates each day

    Explanation

    The distance between a guard and the hazard is based on the size of the openings in the guard, because larger openings allow fingers or hands to reach farther. OSHA publishes this relationship in a table so guards are set back far enough that no body part can reach the danger zone.

  199. Question 199Machine Guarding

    A ventilation fan's blades are mounted six feet above the working floor. What does 29 CFR 1910.212(a)(6) require?

    1. A guard with openings no larger than 2 inches
    2. A sign warning employees to stay clear of the fan
    3. No guarding, because the blades are above head height
    4. A guard with openings no larger than 1/2 inch Correct answer.

    Explanation

    When the periphery of fan blades is less than seven feet above the floor or working level, the blades must be guarded with openings no larger than one-half inch. The small opening size prevents fingers from reaching the blades.

  200. Question 200Machine Guarding

    An employer supplies special hand tools so operators can feed stock without putting hands in the danger zone. What is OSHA's position on this practice?

    1. The tool requires a variance from OSHA before it may be used
    2. The tool is acceptable only if it is made of nonmetallic material
    3. The tool may supplement guarding but cannot replace the required point-of-operation guard Correct answer.
    4. The tool satisfies the guarding requirement by itself, so no guard is needed

    Explanation

    Special hand tools may be used to place and remove material, but they supplement rather than substitute for point-of-operation guarding. The machine must still be guarded so a slip of the tool or hand cannot reach the hazard.

OSHA 30 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

General Duty Clause
Section 5(a)(1) of the OSH Act requires employers to furnish a workplace free from recognized hazards that are causing or likely to cause death or serious physical harm.
OSHA fatality reporting time
An employer must report a work-related fatality to OSHA within 8 hours; an in-patient hospitalization, amputation, or loss of an eye must be reported within 24 hours.
OSHA 300A posting period
The annual summary of recordable injuries and illnesses, Form 300A, must be posted from February 1 through April 30 and retained with injury records for five years.
29 CFR 1910
The portion of OSHA regulations containing general industry standards; construction standards appear in 29 CFR 1926 and maritime standards in 29 CFR 1915 through 1918.
Fall protection trigger height
In general industry, fall protection is required when employees are exposed to falls of 4 feet or more to a lower level; construction standards use a 6-foot trigger.
Guardrail height
A standard guardrail has a top rail at 42 inches, plus or minus 3 inches, above the walking surface, with a midrail at approximately 21 inches.
Portable ladder setup
Non-self-supporting ladders are set so the base is one-quarter of the working length from the wall, a 4:1 ratio, and extended 3 feet above the landing.
Stair rail requirement
Stairways with four or more risers need a stair rail system on each unprotected side or edge, and handrails are mounted 30 to 38 inches above the tread nosing.
Minimum exit route width
Exit routes must be at least 28 inches wide at all points, with capacity of 0.2 inch per occupant on level surfaces and 0.3 inch per occupant on stairways.
Written EAP threshold
An employer with more than 10 employees must have a written emergency action plan; employers with 10 or fewer may communicate the plan orally.
Exit route ceiling height
The ceiling of an exit route must be at least 7 feet 6 inches high, and no projection may reduce the route width below the required minimum.
Fire prevention plan contents
A fire prevention plan lists major fire hazards, handling and storage procedures, potential ignition sources, fire protection equipment, and housekeeping responsibilities for controlling accumulations of flammable waste.
Guarding energized parts
Live parts operating at 50 volts or more must be guarded by enclosures, partitions, location in a qualified-person-only room, or elevation at least 8 feet above the floor.
Electrical working space
At least 3 feet of clear working space is required in front of equipment rated 600 volts or less, and the space must be 30 inches wide and 6.5 feet high.
GFCI protection
Ground-fault circuit interrupter protection is required for temporary receptacles and wet or damp locations, and on construction sites for all 120-volt, 15- and 20-ampere outlets.
Flexible cord restrictions
Flexible cords may not substitute for fixed wiring and may not run through walls, ceilings, floors, or doorways, nor be attached to building surfaces.
PPE hazard assessment
The employer must assess workplace hazards, select appropriate personal protective equipment, and certify the written assessment identifying the workplace evaluated and the person certifying.
Employer-paid PPE
OSHA requires employers to pay for required PPE, except non-specialty safety-toe footwear and non-specialty prescription safety eyewear that employees may wear off the job.
Hearing conservation threshold
A hearing conservation program, including audiometric testing and hearing protection availability, is required when noise exposure reaches an 8-hour time-weighted average of 85 decibels.
Respirator fit test
Employees using tight-fitting respirators must pass a fit test before initial use and at least annually, and must complete a medical evaluation before fit testing.
SDS section count
A safety data sheet contains 16 sections in a fixed order; Section 2 covers hazard identification and Section 4 covers first-aid measures.
GHS signal words
Hazard communication labels use only two signal words: Danger for the more severe hazards and Warning for the less severe hazards, matched to the hazard category.
HazCom written program
Employers must prepare and maintain a written hazard communication program describing how labels, safety data sheets, and employee training will be implemented at that workplace.
Secondary container labeling
Portable containers filled from a labeled container must also be labeled, unless the material is used immediately by the employee who dispensed it within the same shift.
Cylinder separation distances
Oxygen and fuel gas cylinders must be separated by at least 20 feet or by a noncombustible barrier at least 5 feet high having a half-hour fire rating.
Powered industrial truck evaluation
Operators must be trained and evaluated, then re-evaluated at least once every three years; refresher training is required after unsafe operation or an accident.
Storage stability rule
Materials stored in tiers must be stacked, blocked, or interlocked and limited in height so they remain stable and secure against sliding or collapse.
Clear aisles requirement
Aisles and passageways must be kept clear and in good repair, and permanent aisles must be marked so stored materials never block access or egress.
Machine guard requirements
Guards must prevent body parts from contacting moving parts, be secure, create no new hazard, and not interfere with normal machine operation or lubrication.
Abrasive wheel clearances
On a bench or pedestal grinder, the work rest must be adjusted to within 1/8 inch of the wheel and the tongue guard within 1/4 inch of the wheel.
Lockout tagout scope
Hazardous energy control applies to servicing and maintenance when a guard must be removed or bypassed, or when a body part enters a machine danger zone.
Power transmission guarding
Pulleys, belts, gears, shafts, sprockets, and chains that form a machine's power transmission system must be guarded to prevent employee contact with moving parts.

OSHA 30 study guide

Introduction to OSHA

What the OSH Act Does

The Occupational Safety and Health Act of 1970 (signed December 29, 1970; effective April 28, 1971) created OSHA and gave it authority to set and enforce standards and to provide training, outreach, and compliance assistance. Coverage extends to most private-sector employers and employees. Excluded are the self-employed, farms that employ only immediate family, and state and local governments unless a federally approved State Plan covers them; federal agencies are covered under a separate rule.

The Two Employer Duties

Section 5(a)(1), the General Duty Clause, requires each employer to furnish a workplace free from recognized hazards likely to cause death or serious physical harm. It is a gap-filler used when no specific standard applies, and the hazard must be both recognized and serious. Section 5(a)(2) requires compliance with specific standards; Section 5(b) requires employees to comply with rules that apply to their conduct.

Rights and the Numbers Candidates Miss

Employees may file complaints, participate in inspections (walkaround), review injury logs, access exposure and medical records, and are protected from retaliation under Section 11(c); retaliation complaints must be filed within 30 days. Employers must report a fatality within 8 hours and an in-patient hospitalization, amputation, or loss of an eye within 24 hours. Citations must be posted for 3 working days or until abated, and contested within 15 working days.

Traps and a Rule of Thumb

Traps: treating the General Duty Clause as covering every conceivable hazard; assuming public employees are always covered; swapping the 8-hour and 24-hour reporting clocks; assuming OSHA can never obtain a warrant (it may seek one if entry is refused).

Rule of thumb: remember 8–24–15–3 - 8 hours for a fatality, 24 hours for a hospitalization, 15 working days to contest, 3 working days to post.

Walking-Working Surfaces and Fall Protection

The Trigger Height

General industry's walking-working surfaces rule (29 CFR 1910 Subpart D) was rewritten in 2016. In general industry, fall protection is required at 4 feet - at unprotected sides and edges, above dangerous equipment, and at hoist areas - and holes 4 feet or deeper must be guarded or covered. Construction (Subpart M) uses 6 feet and scaffolds use 10 feet, which is a favorite distractor. Fixed ladders extending more than 24 feet above a lower level require a ladder safety system or personal fall arrest system.

Guardrails, Covers, and Stairs

A standard guardrail has a top rail 42 inches (±3) above the walking surface, a midrail at 21 inches, and toe boards 3.5 inches high, and must withstand a 200-pound force. Hole covers must be secured, marked "HOLE" or "COVER," and support at least twice the intended load. Stairways with four or more risers need at least one handrail; handrails run 30 to 38 inches above the tread nosing, and risers and treads must be uniform.

Ladders

Portable ladders must extend 3 feet above the landing, be set at a 4:1 angle (about 75 degrees), be secured against displacement, carry one person at a time, and be faced while climbing. The top step or cap is not a step. Inspect ladders before use and remove damaged ones from service.

Traps and a Rule of Thumb

Traps: quoting 6 feet on a general-industry question; calling out 45 inches for a top rail; treating a hole cover as satisfying an edge-protection requirement; ignoring the non-fall provisions of Subpart D (housekeeping, aisle width, floor loading).

Rule of thumb: the 4:1 ladder rule - for every 4 feet of working length up, move the base 1 foot out from the wall.

Exit Routes, Emergency Action Plans, and Fire Prevention

Two Ways Out, Kept Clear

Under 1910.36 and 1910.37, a workplace needs at least two exit routes that are remote from each other, at least 28 inches wide, with ceilings at least 7 feet 6 inches high, discharging to a street or refuge area. Exit routes must stay unobstructed, be free of flammable finishes, and be marked by illuminated signs whose "EXIT" letters are at least 6 inches high with 3/4-inch strokes. Exit doors must open from the inside without a key or special tool, and a door serving 50 or more occupants or a high-hazard area must swing in the direction of travel.

Emergency Action Plans and Fire Prevention Plans

1910.38 requires a written EAP whose minimum elements are: procedures for reporting emergencies, evacuation procedures including exit route assignments, procedures to account for all employees after evacuation, and rescue and medical duties for designated employees. Review it with each employee on initial assignment and whenever responsibilities or the plan change. 1910.39 requires a written fire prevention plan listing major fire hazards, handling and storage procedures, potential ignition sources, housekeeping, maintenance of safeguards, and the persons responsible for those controls.

Extinguishers

Portable extinguishers are mounted so the top is no more than 5 feet above the floor, visually inspected monthly, and maintained annually. If employees are expected to use extinguishers, the employer must train them annually; if not, the policy is evacuation only and employees still need to know the alarm and escape routes.

Traps and a Rule of Thumb

Traps: confusing the monthly visual inspection with annual maintenance; forgetting the 50-occupant out-swinging door rule; assuming exit route travel distances match construction or fire code figures.

Rule of thumb: two ways out, 50 swings out, 6-inch letters, 5-foot mount.

Electrical Safety

De-energize First

1910.333(a) requires live parts to be deenergized before employees work on or near them unless de-energizing introduces an additional or increased hazard, or is infeasible because of equipment design or operational limitations. Once de-energized, apply lockout/tagout under 1910.147, verify the absence of voltage with a tester rated for that voltage, and treat the circuit as energized until verification is complete.

Qualified vs. Unqualified Persons

1910.332 requires training for any employee exposed to electrical hazards; qualified persons receive additional training on specific hazards and safe work practices. Unqualified persons must keep at least 10 feet from exposed live parts up to 50 kV. Qualified persons may work closer, using the minimum approach distances in the standard's table plus appropriate PPE, and only when necessary.

Cords, Tools, and GFCIs

Flexible cords may not be used as permanent wiring, spliced, run through doorways or walls, or daisy-chained; damaged cords are removed from service; grounding pins are never removed. Portable tools must be grounded or double-insulated and inspected before use. Ground-fault circuit interrupter protection (tripping in the range of about 5 milliamps) is required for temporary receptacles and construction receptacles.

Traps and a Rule of Thumb

Traps: blending 1910.147 lockout/tagout with 1910.333 work practices; assuming lockout is always required (cord-and-plug equipment unplugged and under exclusive control is an exception); assuming rubber gloves alone make live work acceptable; mixing up 10 feet (unqualified) with closer qualified-person distances.

Rule of thumb: de-energize, lock, tag, test, then touch - never the reverse.

Personal Protective Equipment

Assessment Comes First

Under 1910.132 the employer must assess workplace hazards, certify that assessment in writing (identifying the workplace evaluated, the person certifying, and the date), select appropriate PPE, communicate the selection decisions, train employees, and require the PPE to be worn. PPE sits at the bottom of the hierarchy of controls - after elimination, substitution, engineering controls, and administrative controls.

Who Pays, and What Training Covers

The employer pays for required PPE, with narrow exceptions: non-specialty safety-toe footwear and non-specialty prescription safety eyewear that the employee is allowed to take off-site, everyday clothing, and items the employee chooses to wear. Training must address when PPE is necessary, what PPE is required, how to don, doff, adjust, and wear it, its limitations, and its care, maintenance, useful life, and disposal. Retraining is required when workplace changes make prior training obsolete or when an employee shows he or she does not understand.

Requirements by Body Part

Eye and face protection (1910.133) must meet Z87.1; head protection (1910.135) Z89.1; foot protection (1910.136) Z41. Respiratory protection (1910.134) requires a written program, a medical evaluation before fit testing or use, annual fit testing, annual training, and a user seal check each time the respirator is worn. Hearing protection under 1910.95 kicks in with a hearing conservation program at the 85 dBA TWA action level; the PEL is 90 dBA TWA over 8 hours.

Traps and a Rule of Thumb

Traps: assuming employees pay for hard hats or respirators; delivering training without a documented hazard assessment; fit testing before the medical evaluation; substituting a bump cap for a hard hat.

Rule of thumb: assess, select, train, use, maintain - and the employer pays.

Hazard Communication

One Standard, Four Moving Parts

1910.1200 requires a written program, labels, safety data sheets, and training, all supported by an inventory of the hazardous chemicals present. It applies to hazardous chemicals in the workplace; among the excluded items are hazardous waste, tobacco, articles, ionizing radiation, and biological hazards.

Labels

Supplier labels carry the product identifier, a signal word (DANGER or WARNING), hazard statements, pictograms, precautionary statements, and the supplier's name, address, and phone number. Secondary containers must also be labeled - the only exception is when the material is transferred by an employee and used immediately by that same employee.

Safety Data Sheets: 16 Sections

The first eight sections do the practical work: identification, hazard identification, composition, first aid, firefighting, accidental release, handling and storage, and exposure controls/personal protection. OSHA enforces Sections 1–11 and 16; Sections 12–15 (environmental, disposal, transport, regulatory) are not enforced by OSHA. Electronic access is acceptable only if it is readily available in the work area with a backup.

Training

Training is required at initial assignment and whenever a new chemical hazard is introduced. It must cover methods to detect a release, physical and health hazards, protective measures, and how to read labels and SDSs - including for non-routine tasks.

Traps and a Rule of Thumb

Traps: 16 sections does not mean 16 enforced sections; the environment pictogram is not required by OSHA; trade secret claims never block disclosure to health professionals in an emergency; training is required even for intermittent use.

Rule of thumb: 16, 9, 2 - 16 SDS sections, 9 pictograms (8 required by OSHA), 2 signal words.

Materials Handling, Storage, Use, and Disposal

Storage and Clearance

1910.176 requires materials to be stored so they cannot slide, collapse, or otherwise cause injury, with aisles, passageways, and stairways kept clear. Storage must stay 18 inches below sprinkler deflectors and 36 inches below the ceiling in non-sprinklered areas. Compressed gas cylinders are stored upright with valve protection caps in place and secured against tipping; oxygen and fuel-gas cylinders are separated by 20 feet or a barrier at least 5 feet high with a half-hour fire rating.

Powered Industrial Trucks

1910.178(l) requires formal instruction, practical training, and an evaluation of each operator before they operate a truck, with re-evaluation at least every 3 years - and sooner after an accident, near miss, or unsafe operation. Trainees practice only where they will not endanger other employees. No passengers unless a designated seat is provided; travel with the load low and the mast tilted back; never exceed the rated capacity, and account for load center when using attachments.

Slings and Rigging

Slings are inspected before each use and removed from service when damaged; rated capacity is never exceeded. Sling tension rises sharply as the leg angle flattens toward horizontal, so a choker or shallow-angle hitch can overload hardware that looks adequate.

Traps and a Rule of Thumb

Traps: calling forklift evaluation "annual" (the default is every 3 years); mixing up 18 and 36 inches; applying the clearance to the ceiling rather than the sprinkler deflectors; assuming a refresher is never needed between three-year cycles.

Rule of thumb: 18 under the sprinkler, 36 under the ceiling, 20 feet between oxygen and fuel gas.

Machine Guarding

Where Guarding Is Required

1910.212 requires one or more methods of machine guarding to protect the operator and other employees from the point of operation, ingoing nip points, rotating parts, and flying chips and sparks. Guards must be attached to the machine where possible, must not create a new hazard, and must not be easily bypassed. Hand-feeding stock into the point of operation calls for push sticks, blocks, or other hand tools. Fan blades less than 7 feet above the floor must be guarded with openings no larger than 1/2 inch.

Power Transmission and Abrasive Wheels

1910.219 requires belts, pulleys, shafts, chains, and gears to be guarded when within 7 feet of the floor or working platform. For abrasive wheel machinery (1910.215), the work rest is kept adjusted to within 1/8 inch of the wheel face, and the adjustable tongue guard to within 1/4 inch of the wheel - both readjusted as the wheel wears down.

Lockout/Tagout (1910.147)

LOTO applies to servicing and maintenance where unexpected energization, startup, or release of stored energy could injure an employee. It requires a written program, machine-specific energy control procedures, training for authorized, affected, and other employees, and a periodic inspection at least annually. Lockout is preferred; tagout alone is permitted only where the machine cannot be locked and the employer demonstrates equivalent protection. The classic exception: cord-and-plug equipment that is unplugged with the plug kept under the exclusive control of the servicing employee.

Traps and a Rule of Thumb

Traps: swapping 1/8 and 1/4 inch; assuming LOTO applies to routine production jams (it addresses servicing and maintenance); letting anyone but the person who applied a lock remove it; accepting a guard that blocks only frontal access.

Rule of thumb: lock out, release stored energy, verify zero energy - then put your hand anywhere near the point of operation.

OSHA 30 cheat sheet

Quick reference

Introduction to OSHA

  • The OSH Act was signed December 29, 1970, and OSHA began operating April 28, 1971; the Act covers private-sector employers in the 50 states, DC, and territories.

  • General Duty Clause, Section 5(a)(1): each employer must furnish a workplace free from recognized hazards that are causing or likely to cause death or serious physical harm; it is cited when no specific standard applies.

  • Regulation map: 29 CFR 1910 = general industry, 29 CFR 1926 = construction, 29 CFR 1915-1918 = maritime, 29 CFR 1904 = recordkeeping.

  • Reporting clocks: work-related fatality within 8 hours; in-patient hospitalization, amputation, or loss of an eye within 24 hours.

  • Recordkeeping: OSHA 300 Log, 301 Incident Report, and 300A Annual Summary; the 300A must be posted February 1 through April 30 and injury records kept 5 years.

  • Inspection priority order: imminent danger, fatality/catastrophe, employee complaints and referrals, programmed inspections, then follow-ups.

  • Employee rights: request an inspection, participate in the walkaround, view the 300A, and be protected from retaliation; Section 11(c) discrimination complaints must be filed within 30 days.

  • Employers must post the citation at or near the violation, and must contest a citation within 15 working days of receipt.

  • Approved state plans must be at least as effective as federal OSHA and must cover state and local government employees.

Quick reference

Walking-Working Surfaces and Fall Protection

  • Fall protection trigger: 4 feet in general industry (Subpart D); construction (1926) uses 6 feet for conventional fall hazards.

  • Guardrail geometry: top rail 42 inches plus or minus 3 inches above the surface, midrail at approximately 21 inches, rails able to withstand a 200-pound load.

  • Floor holes must be guarded by a cover or guardrail; covers must be secured, color-coded or marked "HOLE" or "COVER", and support twice the intended load.

  • Stairways with 4 or more risers require a stair rail system on each unprotected side or edge; handrails are mounted 30 to 38 inches above the tread nosing.

  • Fixed ladders extending more than 24 feet above a lower level require a ladder safety system or personal fall arrest system; cages and wells are not permitted on new ladders installed after November 19, 2018.

  • Portable non-self-supporting ladders: set at a 4:1 ratio (base one-quarter of working length from the wall) and extend 3 feet above the upper landing.

  • Housekeeping: every walking-working surface must be kept clean, orderly, and dry, with spills and debris removed promptly.

  • Dockboards must be secured against movement, marked with load capacity, and rated for the loads imposed.

  • Recognized fall protection systems: guardrail system, safety net, personal fall arrest, positioning device, ladder safety system, travel restraint, and designated area.

Quick reference

Exit Routes, Emergency Action Plans, and Fire Prevention

  • At least two exit routes are required where the number of employees, size, or arrangement of the workplace requires them; additional routes are required if a single route could be blocked.

  • Exit route dimensions: minimum 28 inches wide, ceiling at least 7 feet 6 inches high, capacity of 0.2 inch per occupant on level surfaces and 0.3 inch per occupant on stairways.

  • Exit signs must be visible and illuminated; any door or passageway that could be mistaken for an exit must be marked "NOT AN EXIT" or with a sign indicating its actual use.

  • Exit routes must be adequately lit, and emergency lighting is required where exit routes are not continuously illuminated.

  • Doors serving 50 or more occupants, or serving high-hazard areas, must swing in the direction of travel and cannot be locked against egress from the inside.

  • A written Emergency Action Plan is required unless the employer has 10 or fewer employees (then it may be communicated orally); minimum elements are reporting procedures, evacuation procedures, procedures to account for employees, and rescue/medical duties.

  • Fire Prevention Plan contents: list of major fire hazards, handling and storage procedures, potential ignition sources and their control, fire protection equipment, and housekeeping/maintenance responsibilities.

  • Portable fire extinguishers must be mounted, unobstructed, visually inspected monthly, and receive annual maintenance; travel distance to a Class A hazard extinguisher must not exceed 75 feet.

Quick reference

Electrical Safety

  • Before work, equipment must be de-energized, locked/tagged out under 1910.147, and tested to verify the absence of voltage.

  • Working space in front of electrical equipment rated 600 volts or less: at least 3 feet deep, 30 inches wide, and 6.5 feet high, kept clear.

  • Live parts operating at 50 volts or more must be guarded against accidental contact by approved enclosures, partitions, location in a room accessible only to qualified persons, or elevation at least 8 feet above the floor.

  • Flexible cords may not be used as a substitute for fixed wiring and may not run through walls, ceilings, floors, doorways, or be attached to building surfaces.

  • GFCI protection is required for temporary receptacles and wet or damp locations in general industry; construction sites require GFCI protection on all 120-volt, 15- and 20-ampere receptacle outlets.

  • Portable cord-and-plug tools must be visually inspected before use; damaged tools are removed from service, and equipment is either grounded (3-wire) or double-insulated.

  • Only qualified persons may work on or near exposed energized parts; minimum approach distances from Table S-5 apply, and conductive jewelry or clothing is prohibited.

  • Electrical PPE includes rubber insulating gloves (with test date), nonconductive hard hats, face shields, and flame-resistant clothing selected from the incident-energy hazard.

Quick reference

Personal Protective Equipment

  • The employer must perform a hazard assessment of the workplace, select appropriate PPE, and certify the assessment in writing with the workplace evaluated and the person certifying.

  • The employer pays for required PPE, except non-specialty safety-toe footwear and non-specialty prescription safety eyewear that the employee is allowed to wear off the job.

  • PPE training covers when PPE is necessary, what PPE is required, how to don, doff, adjust, and wear it, its limitations, and care and disposal; training must be certified in writing.

  • Recognized consensus standards: eye and face protection ANSI Z87.1, head protection ANSI Z89.1, foot protection ASTM F-2413.

  • Defective or damaged PPE must not be used and must be removed from service and replaced.

  • A hearing conservation program (audiometric testing, hearing protection, training) is triggered at an 8-hour TWA noise exposure of 85 dBA; feasible engineering controls are required at 90 dBA.

  • Respirator users need a medical evaluation, annual fit testing for tight-fitting models, and training before use; fit testing cannot precede medical clearance.

  • Fall arrest harnesses and lanyards are inspected before each use and after any fall event, with damaged components removed from service.

Quick reference

Hazard Communication

  • Employers must maintain a written hazard communication program, a list of hazardous chemicals in the workplace, and a safety data sheet for each hazardous chemical.

  • Container labels must include product identifier, signal word, hazard statement(s), pictogram(s), precautionary statement(s), and the name, address, and phone number of the manufacturer or supplier.

  • Safety data sheets have 16 sections in a fixed order; Section 2 is hazard identification and Section 4 is first-aid measures.

  • OSHA requires 8 of the 9 GHS pictograms; the environment pictogram is not adopted by OSHA.

  • Only two signal words exist: "Danger" for more severe hazards and "Warning" for less severe hazards.

  • Training is required at the time of initial assignment and whenever a new chemical hazard is introduced into the work area.

  • Labels on incoming containers may not be removed or defaced; secondary containers must be labeled unless the material is used immediately by the employee who transferred it within that work shift.

  • Employees must have unobstructed access to safety data sheets; electronic access is permitted if no barriers to access exist.

  • Pipes, hoses, and similar conveyances must be labeled with the product identifier and appropriate hazard information.

Quick reference

Materials Handling, Storage, Use, and Disposal

  • Stored material stacked in tiers must be stacked, blocked, or interlocked and limited in height so that it is stable and secure against sliding or collapse.

  • Aisles and passageways must be kept clear and in good repair, and permanent aisles must be marked; stored material may not block exits, electrical panels, or fire equipment.

  • Compressed gas cylinders are stored upright and secured, with valve protection caps in place; oxygen and fuel gas cylinders are separated by 20 feet or a 5-foot-high noncombustible barrier with a half-hour fire rating.

  • Floor load limits must be posted where applicable and never exceeded by stored materials or equipment.

  • Powered industrial truck operators must be trained and evaluated, re-evaluated at least every three years, and retrained after unsafe operation or an accident; trucks are inspected before each shift.

  • Slings, chains, and rigging hardware are inspected before use and marked with their rated capacity; damaged rigging is removed from service.

  • Combustible waste, scrap, and debris must be removed from work areas promptly to prevent accumulation and fire load.

  • Materials must be moved, stored, and disposed of so as not to create hazards from falling, rolling, shifting, or puncturing containers.

Quick reference

Machine Guarding

  • Guards must prevent contact with moving parts, be secure and tamper-resistant, create no new hazard such as a pinch point, and not interfere with normal operation or lubrication.

  • Machine areas requiring guarding: point of operation, power transmission apparatus, rotating and reciprocating parts, transverse moving parts, and other moving parts that could injure an operator.

  • Guard types include fixed, interlocked, adjustable, and self-adjusting guards, plus devices such as presence-sensing, two-hand controls, and gates.

  • Guard openings and distance from the point of operation follow a table relationship (Table O-10 for mechanical power presses): the larger the opening, the greater the required distance.

  • Abrasive wheel grinders: work rest adjusted to within 1/8 inch of the wheel, tongue guard within 1/4 inch of the wheel, and wheels ring-tested before mounting.

  • Lockout/tagout applies to servicing and maintenance when a guard must be removed or bypassed, or when any body part must be placed in a danger zone during normal production.

  • Operators and maintenance workers must be trained in safe operating procedures, guard use, and energy-control procedures for their assigned machines.

  • Hand-feeding tools such as push sticks are required where feasible to keep hands out of the point of operation.

OSHA 30 key terms

OSH Act of 1970

The federal law that created OSHA and requires employers to provide workplaces free from recognized hazards likely to cause death or serious physical harm. It covers most private-sector employers and their employees in the United States.

Related: General Duty Clause, Whistleblower Protection (Section 11(c))
General Duty Clause

Section 5(a)(1) of the OSH Act, which requires an employer to furnish a workplace free of recognized hazards that cause or are likely to cause death or serious physical harm, even when no specific standard covers the hazard.

Related: OSH Act of 1970, Imminent Danger
Imminent Danger

Any condition or practice where a workplace hazard could reasonably be expected to cause death or serious physical harm immediately, or before normal enforcement steps could remove it. OSHA treats reports of such conditions as its top inspection priority.

Related: General Duty Clause
Recordable Injury or Illness

A work-related injury or illness that must be entered on the employer's OSHA 300 Log because it involves death, days away from work, restricted work, job transfer, medical treatment beyond first aid, loss of consciousness, or a significant diagnosis.

Related: Imminent Danger
Whistleblower Protection (Section 11(c))

An OSH Act provision that forbids employers from retaliating against employees who exercise safety and health rights, such as filing a complaint, taking part in an inspection, or reporting an injury or illness.

Related: OSH Act of 1970
Competent Person

A person who can identify existing and predictable hazards in the surroundings or working conditions and who has authority to take prompt corrective measures to eliminate them. The role applies to decisions about fall protection, ladders, and similar hazards.

Related: Fall Protection, Guardrail System
Fall Protection

The systems and practices used to prevent or arrest falls from heights, such as guardrails, safety nets, covers, and personal fall arrest. In general industry, protection is required when employees work 4 feet or more above a lower level.

Related: Personal Fall Arrest System (PFAS), Guardrail System, Hole Cover
Personal Fall Arrest System (PFAS)

Equipment that stops a falling worker, made up of an anchorage, connectors, a full body harness, and a lanyard or lifeline with a deceleration device. It must be rigged to limit free fall and arresting forces.

Related: Anchorage, Fall Protection
Anchorage

A fixed structural point or object to which fall arrest equipment is attached. For personal fall arrest it must support at least 5,000 pounds per employee, or be designed by a qualified person with a safety factor of at least two.

Related: Personal Fall Arrest System (PFAS)
Guardrail System

A barrier of rails and posts installed along open sides, edges, and platforms to prevent falls, typically with a top rail about 42 inches high, a midrail, and a toeboard where required.

Related: Fall Protection, Hole Cover
Hole Cover

A rigid cover placed over an opening in a floor, roof, or other walking surface to stop people and objects from falling through. Covers must support at least twice the intended load, be secured, and be marked as a hole or cover.

Related: Guardrail System, Fall Protection
Ladder Safety System

A device attached to a fixed ladder, such as a carrier, cable, or lifeline, that protects climbers from falling. It must be inspected before use and used according to the manufacturer's instructions.

Related: Fall Protection, Competent Person
Stairway Handrail

A rail along the side of a stairway that gives employees something to grip for balance and support. Stairways with four or more risers, or rising more than 30 inches, generally need at least one handrail.

Related: Guardrail System
Means of Egress

A continuous and unobstructed path of travel from any point in a building to a public way. It is made up of three parts: exit access, the exit itself, and exit discharge.

Related: Exit Route, Exit Sign
Exit Route

A continuous, unobstructed way out of a workplace that includes exit access, the exit, and the path to the outside. Exit routes must stay free of obstructions and be marked so employees can find them.

Related: Means of Egress, Exit Sign
Exit Sign

A sign that clearly marks the direction to an exit, with letters at least 6 inches high and legible from the nearest point in the exit access. Signs must be illuminated as required so they remain visible.

Related: Exit Route, Means of Egress
Emergency Action Plan (EAP)

A written plan describing how employees respond to emergencies, including reporting procedures, evacuation or shelter-in-place assignments, procedures to account for employees, and rescue or medical duties.

Related: Fire Prevention Plan (FPP), Employee Alarm System
Fire Prevention Plan (FPP)

A written plan that lists major workplace fire hazards, describes proper handling and storage of flammable materials, and explains how fire prevention equipment and controls are maintained to stop fires before they start.

Related: Emergency Action Plan (EAP), Fire Extinguisher Classes
Employee Alarm System

A device or system used to warn employees of fire or other emergencies and to trigger the needed response. It must be distinctive, perceptible over background noise, and tested as required.

Related: Emergency Action Plan (EAP)
PASS

A four-step method for using a portable fire extinguisher: Pull the pin, Aim at the base of the fire, Squeeze the handle, and Sweep the nozzle from side to side while staying at a safe distance.

Related: Fire Extinguisher Classes
Fire Extinguisher Classes

The letter ratings A, B, C, D, and K that identify which fires an extinguisher may be used on: ordinary combustibles, flammable liquids, energized electrical equipment, combustible metals, and cooking oils.

Related: PASS, Fire Prevention Plan (FPP)
De-energized

The condition in which a circuit or equipment has been disconnected from every energy source and verified to have no voltage. Work on or near exposed energized parts is allowed only under strict, limited conditions.

Related: Energy Control Procedure (Lockout/Tagout), Arc Flash
Ground-Fault Circuit Interrupter (GFCI)

A device that senses small current leaks to ground and quickly shuts off power to prevent shock. Portable GFCIs are required for temporary receptacles used in construction and similar wet or outdoor work.

Related: Assured Equipment Grounding Conductor Program, Arc Flash
Assured Equipment Grounding Conductor Program

A written program of visual inspections and continuity tests that verifies the grounding path of cord-and-plug tools and cords, used in some settings as an alternative to GFCI protection.

Related: Ground-Fault Circuit Interrupter (GFCI)
Arc Flash

A sudden, high-energy electrical discharge through air that releases intense heat, light, pressure, and molten metal. It can burn, blind, or throw a worker, which is why equipment is de-energized before work.

Related: De-energized, Ground-Fault Circuit Interrupter (GFCI)
Hazard Assessment (PPE)

A review of workplace tasks and conditions to decide whether hazards are present or likely and what eye, face, head, foot, or hand protection is needed. Employers must document and certify the assessment.

Related: Personal Protective Equipment (PPE), Eye and Face Protection
Personal Protective Equipment (PPE)

Clothing and gear such as hard hats, gloves, goggles, and safety shoes worn to reduce exposure to hazards. PPE is the last line of defense and does not replace engineering or administrative controls.

Related: Hazard Assessment (PPE), Eye and Face Protection
Eye and Face Protection

Devices such as safety glasses, goggles, and face shields that protect against flying particles, dust, chemicals, and light radiation. They must meet the required impact standard and fit the wearer properly.

Related: Personal Protective Equipment (PPE), Hazard Assessment (PPE)
Safety Data Sheet (SDS)

A standardized document with 16 sections describing a hazardous chemical's identity, hazards, safe handling, first aid, firefighting measures, and spill response. Employers must keep SDSs accessible to workers on each shift.

Related: Hazard Communication Program, GHS Pictogram
GHS Pictogram

A black hazard symbol on a white background inside a red diamond border that appears on labels and safety data sheets to signal a specific hazard class, such as flammability, acute toxicity, or corrosion.

Related: Safety Data Sheet (SDS), Hazard Communication Program
Hazard Communication Program

The employer's written program describing how labels, safety data sheets, and training will be handled for hazardous chemicals in the workplace, including a list of the chemicals present.

Related: Safety Data Sheet (SDS), GHS Pictogram
Powered Industrial Truck

A mobile, power-driven vehicle used to carry, push, pull, lift, stack, or tier material, such as a forklift. Operators must be trained and evaluated on the specific truck in use at least every three years.

Related: Load Rating (Working Load Limit), Material Storage and Stacking
Load Rating (Working Load Limit)

The maximum load that a sling, chain, hook, or other lifting component is designed to handle safely, as marked by the manufacturer. Equipment must never be loaded beyond that rating.

Related: Powered Industrial Truck, Material Storage and Stacking
Material Storage and Stacking

Keeping stored materials on stable, level surfaces, limiting stack height, and placing heavy or bulky items low. Stored material must not block exits, sprinkler heads, or electrical panels.

Related: Load Rating (Working Load Limit)
Point of Operation

The area on a machine where work is actually performed on the material, such as where a blade cuts or a press punches. It must be guarded so hands and other body parts cannot reach the danger area.

Related: Machine Guard, Nip Point
Machine Guard

A barrier, device, or location that keeps employees from contacting moving machine parts or other hazardous areas. Guards must be attached to the machine and must not be easily removed or bypassed.

Related: Point of Operation, Nip Point
Nip Point

A point where two rotating parts move toward each other, or where a rotating part passes a stationary surface, creating a pinching or crushing hazard, such as between gears or a belt and pulley.

Related: Machine Guard, Point of Operation
Energy Control Procedure (Lockout/Tagout)

A documented method for shutting down, isolating, blocking, and locking out energy sources before machines are serviced, including steps to verify isolation and release any stored energy.

Related: Machine Guard, De-energized

OSHA 30 study plan

8 weeks · About 6 hours per week

Week 1

Introduction to OSHA & Walking-Working Surfaces and Fall Protection

  • State the employer's General Duty Clause obligations and list at least five employee rights under the OSH Act, including the right to request an inspection and to refuse imminently dangerous work.

  • Rank OSHA's inspection priorities in order and match each violation category (other-than-serious through willful) to its penalty range and abatement rules.

  • Match each walking-working surface (dock, pit, roof, ladder, stairway) to its general-industry fall-protection trigger height and state the exception for each.

  • Label the components of a guardrail system and state the minimum top-rail height, mid-rail position, and load resistance for bothstructural and personal fall arrest use.

  • Identify the four hazard categories on a walking-working surface checklist: falls, slips, trips, and falling objects.

Your checkpoint

A single-page reference card listing all trigger heights and guardrail dimensions, plus a score of at least 80% on a 25-question fall-protection self-quiz.

Week 2

Walking-Working Surfaces and Fall Protection

  • Apply ladder rules by calculating the correct 4:1 setup angle and the required extension above a landing for a given working length.

  • Compute total fall distance for a personal fall arrest system by adding free fall, deceleration distance, worker height, and the safety margin, and explain why the anchor point height matters.

  • Differentiate hole covers, guardrails, and personal fall arrest systems by stating the strength, labeling, and securement requirement for each.

  • Write your own 10-defect written worksite scenario and cite the specific standard requirement violated by each defect.

  • Describe the minimum requirements for stairway railings, dockboard use, and housekeeping on walking-working surfaces.

Your checkpoint

A self-authored 10-defect scenario with a written answer key citing the violated requirement for each defect, plus 30 practice questions completed at 85% or better.

Week 3

Electrical Safety & Exit Routes, Emergency Action Plans, and Fire Prevention

  • Contrast grounded, double-insulated, and GFCI-protected systems and state when an assured equipment grounding conductor program is permitted instead of GFCI protection.

  • Identify the guarding, clamping, and marking requirements for live parts and state the minimum approach distances for overhead lines.

  • Describe the required elements of an exit route: capacity, width, lighting, signage, and the minimum number of exit routes for a given occupant load.

  • Sequence the required content of an Emergency Action Plan and a Fire Prevention Plan and explain which employers may use a written plan versus an oral one.

  • Explain the inspection, testing, and maintenance intervals for portable fire extinguishers and the rules for a fire prevention plan's housekeeping provisions.

Your checkpoint

A completed comparison table of EAP versus Fire Prevention Plan required elements with a citation for each row, plus a 25-question quiz at 80% or better.

Week 4

Electrical Safety & Machine Guarding

  • Walk through the lockout/tagout sequence in order and explain the requirement for verifying de-energization and for removing a lock left by an absent worker.

  • Match each machine motion (rotating, reciprocating, traversing, cutting) to an appropriate guard type and justify the choice.

  • State the point-of-operation guarding requirement and explain how a barrier guard's distance from the hazard relates to the size of the opening.

  • List the three categories of machine hazards (point of operation, power transmission, other moving parts) and give an example of each from your own workplace or a familiar trade.

  • Explain the circumstances under which a machine may be operated with a guard removed.

Your checkpoint

A timed 40-question mixed exam covering Domains 1 through 4 and 8 with a recorded score of 80% or better and every miss logged by domain.

Week 5

Machine Guarding

  • Evaluate a machine for guarding needs by listing the point of operation, power transmission apparatus, and other moving parts before selecting a control.

  • Distinguish guards from devices and name four device types (presence sensing, two-hand control, gate, holdout/restraint) with one limitation of each.

  • State the guarding requirements for abrasive wheels, mechanical power presses, and woodworking machinery, including the role of a spreader and anti-kickback device.

  • Explain when machine-specific training is required before a worker operates a guarded machine, and what the training must cover.

  • Restate the rule that guards must be anchored, must not create a new hazard, and must not be removed or bypassed during operation.

Your checkpoint

A two-page guard-selection matrix mapping at least eight machine motions to a guard or device and the reason for the match, plus a 30-question machine-guarding quiz at 85% or better.

Week 6

Hazard Communication & Personal Protective Equipment

  • Break down a Safety Data Sheet into all 16 sections and locate the hazard identification, exposure controls, and physical/chemical property data within the first few minutes of reading.

  • Apply label requirements by naming the required pictograms, signal words, and precautionary statements, and explain the manufacturer's versus the employer's labeling duty.

  • Classify hazards by body part and select the correct eye/face, head, hand, and foot protection for each of three job roles.

  • State the employer's written hazard assessment and certification obligations and the training requirements for each item of PPE.

  • Explain the rules for defective or damaged PPE, employee-owned equipment, and when payment for PPE is the employer's responsibility.

Your checkpoint

A written hazard assessment and PPE selection sheet for three distinct job roles, plus a completed SDS scavenger hunt identifying all 16 sections.

Week 7

Materials Handling, Storage, Use, and Disposal & Exit Routes, Emergency Action Plans, and Fire Prevention

  • Apply storage rules by determining the maximum stack height and clearance from sprinkler heads, ceilings, and walls for combustible and noncombustible materials.

  • Determine required aisle width, stacking stability practices, and the tie-off or interlocking method for bagged and boxed material.

  • Distinguish the storage, handling, and use rules for compressed gas cylinders from those for flammable liquids, including separation and ventilation.

  • Check a written workplace scenario against exit-route and fire-prevention rules and list every housekeeping, blocking, or accumulation violation found.

  • Explain the requirements for disposing of flammable waste and oily rags to prevent spontaneous ignition.

Your checkpoint

A one-page storage and materials-handling rule card, plus a scored 25-question quiz on Domains 3 and 7 at 85% or better.

Week 8

Walking-Working Surfaces and Fall Protection & Machine Guarding

  • Re-drill fall protection and machine guarding by rewriting from memory the trigger heights, guardrail dimensions, guard types, and device types.

  • Complete two full-length timed 100-question practice exams and log every incorrect answer by domain and sub-topic.

  • Re-study any domain scoring below 80% and re-test that domain only until it clears the threshold.

  • Distill the entire course into a personal 40-fact list built from memory, then verify each fact against your notes.

Your checkpoint

Two timed practice exams scored at 85% or better with a written remediation log showing each weak domain closed out.

Milestones

Week 2: Can state, without notes, the general-industry fall-protection trigger heights for all major surfaces and compute total fall distance for a sample system correctly.

Week 4: Score 80% or better on the cumulative 40-question exam across the first five domains studied, with no domain below 70%.

Week 6: Can reconstruct the 16 SDS sections and the PPE hazard-assessment obligation from memory, and complete the three-role PPE selection sheet unaided.

Week 8: Two full-length practice exams at 85% or better, every missed item logged and remediated, and a self-written 40-fact review sheet complete.

OSHA 30 exam day

Your checklist

Government-issued photo ID

OSHA-authorized trainers are expected to verify each student's identity before issuing a completion card. Bring the ID you enrolled with, and confirm in advance which forms of ID your provider accepts - policies on expired IDs, digital IDs, and name mismatches vary by provider.

Enrollment confirmation and provider contact info

Bring your registration confirmation with the course title (30-Hour Construction or 30-Hour General Industry), dates, start time, and the trainer's phone number in case of a delay or location problem.

Confirmation of which 30-hour course you are in

Construction and General Industry are separate curricula. Verify your registration matches the card you need; switching tracks mid-course is generally not allowed.

Notebook and pen (or note-taking app)

Outreach courses are participation-based. Written notes help on any end-of-course assessment, and trainers often check engagement.

Any pre-course materials the provider sent

Some providers distribute reading, a syllabus, or pre-test links. Complete these before day one - confirm with the provider whether anything is required.

Exam format and passing score, confirmed in writing

There is no single national OSHA exam; the end-of-course test, if any, is set by the training provider. Ask ahead of time: number of questions, format, passing score, retake policy, and whether the exam is open-book.

Attendance/make-up policy, confirmed in writing

Outreach training requires full attendance across all 30 hours, and providers must document attendance. Ask how missed time is handled (make-up session, re-enrollment, fee) before you start.

Online-course tech check (if applicable)

For remote or online delivery, confirm the platform, whether camera/microphone is required, whether sessions are monitored, and whether you may join from a phone. Test your camera, mic, and internet the day before.

Language-of-instruction and accessibility needs

Ask whether instruction and any exam are in your preferred language and what accommodations are available. Arrange interpreters or accommodations in advance - do not assume they are available on the day.

Reschedule and refund terms

Know the provider's cutoff for rescheduling and whether fees are transferable, in case of illness or an emergency.

Card issuance timeline

Ask when and how your completion card will be issued (many trainers issue within a set window after course completion) and how to replace it if lost.

Means to stay comfortable for a long day

Thirty hours is typically spread over several days with limited hours per day. Plan for full-day sessions: water, snacks, and any medication you may need.

Plan the day

72 hours before

Re-confirm every logistics detail in writing: course track (Construction vs. General Industry), dates and daily start/end times, location or platform link, ID requirements, exam format and passing score, and attendance/make-up rules. Flag anything the provider cannot confirm.

72 hours before

Do a focused review of high-yield topics: the Focus Four hazard categories (falls, struck-by, caught-in/between, electrocution), PPE, hazard communication, ladders and scaffolds, excavation, electrical safety, and recordkeeping/reporting basics. Skim the table of contents of 29 CFR 1926 and/or 1910 so the citations feel familiar.

72 hours before

Resolve any conflict that could cost you attendance hours - travel, work shifts, childcare. Because attendance is documented hour by hour, an absence is harder to fix than a late arrival.

24 hours before

Pack your ID, confirmation, notebook, pen, charger, and any provider materials. Lay out clothes and plan your route or commute time.

24 hours before

If the course is online or remote-proctored, run a full tech rehearsal: log into the platform, test camera and microphone, confirm browser version, and identify a quiet, well-lit room with a stable connection.

24 hours before

Sleep a full night. Long-format training days reward attention more than last-minute cramming.

Morning of

Eat a real meal, arrive or log in 15–30 minutes early for check-in and ID verification, and silence your phone.

Morning of

Re-read your registration for the exact start time and room or link - do not rely on memory.

During the course

Attend every session and sign or check in as instructed. Note the daily break schedule and return on time; off-task minutes may not count toward the required hours.

During the course

Participate: ask questions, write down the trainer's answers to confusing points, and mark topics you want to review before any end-of-course test.

During the test

Read each question fully and watch for qualifiers such as 'always,' 'minimum,' 'employer,' and 'employee.' Many items turn on whether a duty falls on the employer or the worker.

During the test

Answer every question - an unanswered item is almost never better than a reasoned choice. Flag uncertain items, return to them if time allows, and confirm the passing score and retake policy before you submit.

Rules to check

  • Attendance is the core requirement: you must complete the full 30 hours of instruction. Partial attendance generally does not earn a card, and make-up of missed time is handled under the provider's policy - confirm it in writing before the course begins.

  • You must present acceptable government-issued photo ID, and the name on your completion card will generally match the name on that ID. Ask the provider about name-change or nickname issues in advance.

  • Do not have someone else attend, sign in, or take a test on your behalf, and do not share answers. Impersonation and cheating can result in denial of a completion card; online sessions are often monitored.

  • Breaks and lunch are set by the trainer. Leaving the room or the platform outside those times may reduce documented instructional hours - ask how the provider records time away.

  • Course completion cards are issued through the OSHA-authorized trainer who delivered the class, not directly by OSHA, and the 30-hour card documents training completion rather than certifying you as a 'certified' safety professional. Confirm issuance timing and replacement procedures with the provider.

  • Any end-of-course exam - its length, format, open- or closed-book status, passing score, and retake rules - is set by the training provider, not by a single national standard. Get those terms before test day rather than after.

  • Follow the provider's device and recording policy. Unless you are told otherwise, keep phones silent and do not photograph, record, or livestream instruction or exam content.

  • If a question on the exam seems to conflict with what you were taught, answer according to the course material and the cited OSHA standard, and raise the discrepancy with the trainer afterward rather than debating it during the test.

OSHA 30 FAQ

How many OSHA 30 practice questions are available?

The practice set has 200 OSHA 30 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many OSHA 30 flashcards are available?

The flashcard set has 32 OSHA 30 cards. Each card shows the term and its definition.

Which topics does the OSHA 30 study material cover?

The OSHA 30 study material has 8 sections, including Introduction to OSHA, Walking-Working Surfaces and Fall Protection, and Exit Routes, Emergency Action Plans, and Fire Prevention.

What format facts does the catalog list for the OSHA 30 exam?

The catalog lists a duration of 1800 minutes and these item types: in-person class delivered by an OSHA-authorized Outreach trainer, online class delivered by an OSHA-accepted online provider, and no standardized test; testing is optional and at the trainer's discretion for the OSHA 30 exam.