NCCCO Rigger Level I Practice Test

NCCCO Certified Rigger Level I

NCCCO Rigger Level I overview

  • 199 practice questions
  • 32 flashcards
  • 4 study guide topics
  • 37 key terms

What you'll study

  • Inspect rigging before use
  • Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots
  • Recognize associated hazards
  • Use various types of rigging equipment and basic hitches and their applications

The NCCCO Certified Rigger Level I credential is a nationally recognized certification for individuals who handle and move loads using synthetic slings, chain slings, wire rope slings, metal mesh slings, and rigging hardware. It is designed for those who perform simple, repetitive rigging tasks when the load weight, center of gravity, and rigging configuration are known or provided. The certification process includes both a written and a practical examination. The written exam consists of 60 multiple-choice questions to be completed in 60 minutes, and the practical exam demonstrates basic rigging competency. To be eligible, candidates must be at least 18 years old, comply with CCO’s Substance Abuse Policy and Code of Ethics, and pass both exams. The certification is valid for five years, and candidates have 12 months from passing their first exam (written or practical) to pass the other. Recertification requires passing the applicable written exam and complying with policies; no practical exam is required for recertification. Preparation should focus on the four job domains: inspecting rigging before use; identifying, selecting, and attaching rigging with basic knowledge of hitch configurations, capacities, and knots; recognizing associated hazards; and using various types of rigging equipment and basic hitches and their applications. This guide provides an overview of the exam and answers common questions to help candidates prepare effectively.

Common mistakes

Approving a sling for use based only on a quick visual glance, without checking the ID tag or the removal-from-service criteria (broken wires, heat damage, tag missing).

Candidates treat inspection as a formality and rely on 'it looks fine,' because they have not memorized the specific rejection thresholds and required tag information.

What to do instead

Practice a fixed inspection sequence for every sling: tag present and legible, then material-specific defects (broken wires in a defined lay length for wire rope, cuts/glazing for synthetic, cracks/wear for alloy chain), then hardware. State the rejection criterion out loud for each defect you find.

Using a sling with a missing or illegible capacity tag because the hardware 'looks heavy enough' to guess a rating.

Candidates want to keep the lift moving and assume similar-looking slings share ratings, but capacity depends on material, size, configuration, and splice/end fitting.

What to do instead

Apply the rule that an unidentifiable sling is out of service. When practicing, cover tags and force yourself to identify the sling type and look up the rating rather than estimating.

Selecting a sling based on the vertical (single-leg) capacity when the actual hitch is a choker or basket.

Candidates memorize one capacity number per sling and forget that the same sling has different ratings for vertical, choker, and basket configurations.

What to do instead

Always state the hitch first, then the configuration-specific capacity, then the applicable efficiency factor. Build a habit of writing 'capacity = vertical rating × configuration factor' before rigging.

Ignoring the sling angle from horizontal when calculating leg tension, treating a two-leg lift as if each leg carries half the load regardless of angle.

Candidates underestimate how quickly tension rises as legs flatten, and they confuse load share with tension.

What to do instead

Work multi-leg problems using the tension formula (leg tension = load share ÷ sin of angle from horizontal) and drill angles of 60, 45, and 30 degrees until the tension multipliers are automatic.

Attaching a choker hitch without confirming the choke is seated and snug, or choking on a sharp corner or fitting without protection.

Candidates focus on getting the hook on the load and skip the seating step, and they do not connect choker efficiency loss with poor choke placement.

What to do instead

Follow a choke checklist: choke point clear of fittings and sharp edges, softener or corner protection in place, choke fully seated before tension, and reduced capacity applied.

Tying or relying on a knot in a sling or tag line where a proper hitch or hardware is required, or using a knot whose strength loss is unknown.

Candidates overestimate knot security and do not know that knots sharply reduce rope strength and can slip under cyclic load.

What to do instead

Learn the small set of knots actually used in rigging (e.g., bowline, clove hitch, timber hitch) and their applications and limitations, and default to hardware or a proper hitch for load-bearing connections.

Standing inside the fall zone or under the load while guiding it, or placing hands on the load instead of using a tag line.

Candidates want control and a good view, and they underestimate how far a load or rigging can swing or drop.

What to do instead

Rehearse position discipline: tag line from outside the fall zone, never under a suspended load, and identify the swing path before the lift starts. State your escape route before signaling.

Missing the hazard of a sharp edge, weld bead, or corner under a sling, or missing abrasion against adjacent structure during the lift.

Candidates look at the load's overall shape rather than the contact points, and they do not visualize the load path during travel.

What to do instead

Walk the entire sling path from hook to attachment and back, checking every contact point for edges, heat, and abrasion, and add softeners or corner protection before tensioning.

Rigging a load without confirming the center of gravity, causing an unbalanced or tilting pick, or attaching legs asymmetrically on an off-center load.

Candidates assume the geometric center equals the center of gravity and do not check for internal weight distribution or attached components.

What to do instead

Identify or estimate the center of gravity before choosing attachment points, use a trial lift to confirm level, and adjust leg lengths or attachment points rather than forcing the load level.

Mismatching hardware-using a hook with too small a throat opening, a shackle pin that can rotate loose, or a hook without a latch/mousing in a load-bearing application.

Candidates match hardware by size impression rather than by rated capacity, fit, and the requirement for latches or mousings to prevent load release.

What to do instead

Check hardware against three criteria every time: rated capacity at least equal to the required load, correct fit (throat and pin seated, no side loading), and secure closure (latch or mousing as required).

Exam requirements can change. Confirm current details with the exam provider.

NCCCO Rigger Level I practice

199 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Inspect rigging before use

    Before a wire rope sling is placed in service, the rigger should inspect it primarily to confirm that it is free of conditions that could do what?

    1. Reduce its rated capacity or cause failure under load Correct answer.
    2. Change the color of the identification tag
    3. Alter the load's weight
    4. Increase the load's center of gravity

    Explanation

    A pre-use inspection looks for damage or defects that reduce a sling's strength or that could cause sudden failure under load. Cosmetic and load-weight issues are unrelated to sling integrity.

  2. Question 2Inspect rigging before use

    A rigger finds a wire rope sling with several broken outer wires concentrated in one strand. What is the correct action?

    1. Use it at half the rated capacity
    2. Use it only for vertical lifts
    3. Remove it from service Correct answer.
    4. Tag it and reuse after one shift

    Explanation

    Broken wires reduce the strength of a wire rope sling, and clustered breaks in one strand are a removal criterion. Damaged slings must be taken out of service, not derated informally.

  3. Question 3Inspect rigging before use

    Which condition on a synthetic web sling most clearly requires removal from service?

    1. A faint crease from storage
    2. A cut or snag that exposes or severs load-bearing fibers Correct answer.
    3. A light dust coating
    4. A slightly faded identification tag

    Explanation

    Cuts and snags that damage load-bearing fibers reduce capacity and are removal criteria for web slings. Surface dust, fading tags, and storage creases do not affect strength.

  4. Question 4Inspect rigging before use

    When inspecting a chain sling before use, the rigger should look specifically for which of the following?

    1. Dirt inside the master link
    2. Fading paint on the tag
    3. Stretch, cracks, and gouges in the links Correct answer.
    4. Loose fibers at the end

    Explanation

    Chain slings are inspected for deformation such as stretch, plus cracks, gouges, and wear at link contact points. Loose fibers describe synthetic slings, and surface dirt or paint does not affect strength.

  5. Question 5Inspect rigging before use

    A shackle is being inspected before use. Which finding indicates it should be removed from service?

    1. A bent pin or elongated bow Correct answer.
    2. A manufacturer's stamp on the bow
    3. A slightly worn identification tag
    4. A lightly oiled pin thread

    Explanation

    Deformation such as a bent pin or stretched bow indicates the shackle has been overloaded and must be removed. Light oil, stamps, and tag wear do not affect structural integrity.

  6. Question 6Inspect rigging before use

    What does the rigger check to confirm a sling's rated capacity before use?

    1. The number of people on the crew
    2. The sling's identification tag or permanent marking Correct answer.
    3. The color of the sling's cover
    4. The weight of the load being lifted

    Explanation

    Rated capacity is established by the sling's tag or permanent marking, which the rigger must read and confirm before use. Color coding may assist but does not by itself establish capacity.

  7. Question 7Inspect rigging before use

    A rigger discovers the identification tag is missing from a web sling. What should be done?

    1. Use it for light loads only
    2. Remove it from service until capacity is verified Correct answer.
    3. Estimate capacity from the sling's width
    4. Attach a handwritten tag with an assumed rating

    Explanation

    A sling without a legible capacity tag cannot be safely rated and must be removed from service until capacity is verified. Guessing or self-tagging capacity is unsafe.

  8. Question 8Inspect rigging before use

    Which inspection finding on a synthetic round sling requires removal from service?

    1. A cover that is intact but dusty
    2. A burn or melt mark on the cover Correct answer.
    3. A small amount of surface lint
    4. A tag that is slightly curled

    Explanation

    Burns and melt marks indicate heat damage that can compromise the load-bearing fibers, so the sling must be removed. Lint, dust, and a curled tag do not affect strength.

  9. Question 9Inspect rigging before use

    Before use, hooks on slings and rigging hardware should be checked for which critical condition?

    1. A tag attached with wire
    2. A slightly dull finish
    3. A hook that is painted
    4. Twist or deformation of the hook body Correct answer.

    Explanation

    Hooks that are twisted, deformed, or have an excessive throat opening have been overloaded and must be removed. Finish, tagging method, and paint do not indicate loss of strength.

  10. Question 10Inspect rigging before use

    What is the purpose of a pre-use inspection of rigging hardware such as shackles, hooks, and links?

    1. To determine the exact weight of the load
    2. To confirm the hardware is free of defects that reduce capacity Correct answer.
    3. To calculate the load's center of gravity
    4. To select the color of the tag

    Explanation

    Pre-use inspection verifies that hardware is undamaged and can carry its rated load. Load weight and center of gravity are determined separately from hardware inspection.

  11. Question 11Inspect rigging before use

    A wire rope sling shows a kink with permanently distorted strands. Why must it be removed from service?

    1. Kinks and distortion reduce strength and can cause uneven loading Correct answer.
    2. Kinks increase the sling's rated capacity
    3. Kinks make the tag hard to read
    4. Kinks only affect the sling's appearance

    Explanation

    A kink that permanently distorts the strands indicates damage that reduces strength and can cause unequal load sharing. Such slings must be removed.

  12. Question 12Inspect rigging before use

    During inspection, a rigger notices a sling's protective cover is torn, exposing the core of a round sling. What is the appropriate action?

    1. Remove it from service Correct answer.
    2. Use it if the core looks clean
    3. Tape the cover and use it
    4. Use it only for choke hitches

    Explanation

    A torn cover exposing the core leaves load-bearing fibers unprotected and subject to damage; the sling should be removed from service. Taping or restricting hitch type does not restore protection.

  13. Question 13Inspect rigging before use

    Which of these is a correct practice when inspecting rigging before use?

    1. Inspect only the portion visible at the hook
    2. Inspect the entire length of each sling, including end fittings Correct answer.
    3. Rely on the previous shift's inspection
    4. Inspect only slings that look dirty

    Explanation

    The full length and all end fittings must be examined because damage can occur anywhere along a sling. Relying on prior inspections or inspecting only visible sections can miss defects.

  14. Question 14Inspect rigging before use

    A chain sling shows noticeable wear at the bearing points between links. Why does this matter?

    1. It improves flexibility of the chain
    2. It indicates the chain was recently cleaned
    3. It reduces link cross-section and therefore strength Correct answer.
    4. It shows the chain is the wrong grade

    Explanation

    Wear at bearing points reduces the cross-sectional area of the links, lowering the sling's strength. Significant wear is a removal criterion.

  15. Question 15Inspect rigging before use

    What should a rigger do if a shackle's pin cannot be fully threaded because the threads are damaged?

    1. Substitute a bolt of similar size
    2. Use the shackle without the pin seated
    3. Remove the shackle from service Correct answer.
    4. Force the pin with a wrench

    Explanation

    Damaged threads prevent the pin from seating fully, so the shackle cannot safely carry load and must be removed from service. Forcing the pin or substituting hardware is unsafe.

  16. Question 16Inspect rigging before use

    Which condition on a synthetic web sling indicates possible chemical damage?

    1. A clean, dry surface
    2. A neatly sewn tag
    3. A slightly loose stitch at the tag
    4. Stiff, brittle, or discolored fibers Correct answer.

    Explanation

    Stiffness, brittleness, or discoloration can indicate chemical attack that weakens synthetic fibers, requiring removal. A clean surface or tag stitching is not a strength concern.

  17. Question 17Inspect rigging before use

    Before use, the rigger should verify that the hardware's rated capacity does which of the following?

    1. Is less than the load weight
    2. Equals the sling's tag color code
    3. Exceeds the load to be lifted Correct answer.
    4. Matches the crane's boom length

    Explanation

    Rigging hardware must have a rated capacity that meets or exceeds the load it will carry. Color codes, boom length, and under-rating are not valid verification criteria.

  18. Question 18Inspect rigging before use

    A hook on a sling has an opening noticeably wider than when new. What does this indicate and what action is required?

    1. Improved hooking ability; continue use
    2. Overloading; remove from service Correct answer.
    3. Normal wear; continue use
    4. A manufacturing defect; return to stock

    Explanation

    An opened or spread hook throat indicates the hook has been overloaded and deformed, so it must be removed from service. Hook deformation is never normal wear.

  19. Question 19Inspect rigging before use

    Which of the following best describes when a pre-use rigging inspection should be performed?

    1. Only after a failure occurs
    2. Only when the rigging looks damaged
    3. Once per month
    4. Before each use of the rigging Correct answer.

    Explanation

    Pre-use inspection is performed before each use so defects are found before a lift. Periodic and post-incident inspections supplement but do not replace it.

  20. Question 20Inspect rigging before use

    A wire rope sling shows heavy corrosion and pitting along its length. What is the correct disposition?

    1. Remove it from service Correct answer.
    2. Oil it and continue use
    3. Use it for vertical lifts only
    4. Reduce the load by ten percent

    Explanation

    Corrosion and pitting reduce wire cross-section and strength, making the sling unfit for service. Oiling or informal derating does not restore capacity.

  21. Question 21Inspect rigging before use

    When inspecting a synthetic sling, why does the rigger check for ultraviolet or sunlight degradation?

    1. It improves the sling's stretch
    2. It makes the sling heavier
    3. It changes the sling's color only
    4. It can weaken synthetic fibers and reduce capacity Correct answer.

    Explanation

    Prolonged UV exposure can degrade synthetic fibers and reduce sling strength, so signs of degradation are a removal concern. Color change alone is not the issue, and UV does not add weight or improve stretch.

  22. Question 22Inspect rigging before use

    A rigger is inspecting end fittings on a wire rope sling. Which finding requires removal from service?

    1. A fitting with a manufacturer's mark
    2. A lightly oiled fitting
    3. A cracked or deformed thimble or fitting Correct answer.
    4. A tag attached with a wire tie

    Explanation

    Cracked or deformed end fittings compromise the sling's termination and require removal. Oil, tag attachment, and manufacturer marks are normal.

  23. Question 23Inspect rigging before use

    What is the primary reason rigging is inspected before each use rather than only periodically?

    1. Inspection is required only for new rigging
    2. Tags must be replaced each time
    3. Periodic inspections are not required
    4. Defects can develop between scheduled inspections Correct answer.

    Explanation

    Damage can occur between scheduled inspections, so each use requires a check to catch new defects. Periodic inspection is still required but does not replace pre-use checks.

  24. Question 24Inspect rigging before use

    A chain sling has a link with a visible crack. What is the correct action?

    1. Use it at reduced capacity
    2. Remove it from service Correct answer.
    3. Cover the crack with paint
    4. Weld the crack and use it

    Explanation

    A cracked link can fail suddenly under load and must be removed from service. Field welding or painting over cracks is unsafe and prohibited.

  25. Question 25Inspect rigging before use

    During a pre-use inspection, a rigger finds a sling with a legible tag showing capacity but a small area of normal surface wear on the cover. How should the rigger proceed?

    1. Remove it from service for any wear
    2. Cut off the worn area and use it
    3. Use it only for choker hitches
    4. Place it in service if wear does not expose or damage load-bearing fibers Correct answer.

    Explanation

    Normal surface wear that does not expose or damage load-bearing fibers does not by itself require removal. Altering the sling or restricting hitches is not appropriate.

  26. Question 26Inspect rigging before use

    Which document should a rigger consult to determine the original rated capacity of a specific sling before use?

    1. The operator's hand signal reference card
    2. The sling's identification tag or manufacturer's documentation Correct answer.
    3. The site's daily lift permit sign-off sheet
    4. The crane's load chart for the current boom configuration

    Explanation

    Rated capacity is established by the sling manufacturer and is conveyed to the user through the identification tag or accompanying documentation. The tag must be legible and match the sling being used.

  27. Question 27Inspect rigging before use

    A rigger is about to use a sling whose tag is present but illegible. What is the correct disposition?

    1. Remove it from service until capacity is confirmed Correct answer.
    2. Use it only for vertical lifts
    3. Mark the capacity on the tag by hand
    4. Use it at half of the estimated capacity

    Explanation

    A sling whose rated capacity cannot be verified cannot be safely used because the rigger cannot confirm it is adequate for the load. It must be set aside until the capacity is positively established.

  28. Question 28Inspect rigging before use

    Which condition on a shackle body requires the shackle to be removed from service?

    1. Light oil film on the pin threads
    2. A bend or distortion of the shackle body Correct answer.
    3. Minor paint scuffing on the bow
    4. Faint surface discoloration from handling

    Explanation

    Any visible bend, twist, or distortion of a shackle body indicates it has been overloaded or damaged and it no longer has predictable strength. Such hardware must be removed from service.

  29. Question 29Inspect rigging before use

    When inspecting a chain sling, what does a gouge or nick at a link's bearing point most directly reduce?

    1. The flexibility of the chain assembly
    2. The legible stamping on the master link
    3. The color coding of the chain
    4. The link's cross-sectional area and strength Correct answer.

    Explanation

    Wear, nicks, and gouges at bearing points remove metal and reduce the cross-sectional area that carries the load. Sufficient loss of material lowers the link's strength below its rated value.

  30. Question 30Inspect rigging before use

    What is the correct action when a rigger finds a hook whose throat opening has spread wider than the manufacturer's limit?

    1. Use it for light loads only
    2. Attach a second hook to share the load
    3. Close the hook with a hammer and use it
    4. Tag it out of service and remove it Correct answer.

    Explanation

    A hook that has spread has been overloaded or deformed, and its strength and load retention are no longer assured. It must be removed from service rather than repaired in the field.

  31. Question 31Inspect rigging before use

    Before use, the rigger should confirm that rigging hardware is marked with which information?

    1. Date of last paint application
    2. Name of the crane operator
    3. Weight of the crane's counterweight
    4. Rated load or working load limit Correct answer.

    Explanation

    Hardware must be marked by the manufacturer with its rated load or working load limit so the rigger can confirm it is adequate for the intended lift. Unmarked hardware cannot be verified.

  32. Question 32Inspect rigging before use

    A wire rope sling is found with broken outer wires grouped closely together in one area. What does this finding indicate?

    1. A condition that improves flexibility
    2. Localized deterioration that requires removal from service Correct answer.
    3. Normal break-in of a new sling
    4. A cosmetic effect of the galvanizing

    Explanation

    Clustered broken wires indicate localized deterioration and loss of strength in that section of the rope. Removal criteria are based on the number and concentration of broken wires.

  33. Question 33Inspect rigging before use

    Why does a rigger inspect the splice or termination on a wire rope sling before use?

    1. To verify the termination has not slipped or pulled apart Correct answer.
    2. To confirm the rope's color code is current
    3. To confirm the sling was made in the current year
    4. To check that the rope is the correct length

    Explanation

    Terminations carry the full load of the sling, and a slipped or damaged splice can fail suddenly. Inspecting it confirms the load path is intact.

  34. Question 34Inspect rigging before use

    A synthetic web sling shows a patch of stiff, brittle fabric with a stiff feel and a distinct odor. What is the most likely cause?

    1. Normal dye lot variation
    2. Ordinary surface dust
    3. Exposure to clean water
    4. Chemical contamination Correct answer.

    Explanation

    Stiffening, brittleness, and unusual odor in synthetic webbing commonly indicate chemical attack, which can severely reduce strength. The sling should be removed from service.

  35. Question 35Inspect rigging before use

    During inspection a rigger finds a synthetic round sling with a fused or melted spot on the cover. What is the correct disposition?

    1. Use it only in a basket hitch
    2. Cover the spot with tape and use it
    3. Remove it from service Correct answer.
    4. Return it to service if the spot is small

    Explanation

    Heat or friction damage can melt or fuse synthetic fibers, destroying their strength even where the damage looks small. Any melted or fused area is a removal criterion.

  36. Question 36Inspect rigging before use

    What is the primary reason a rigger inspects rigging at the start of each shift rather than relying only on periodic inspections?

    1. To record the sling's purchase price
    2. To confirm the rigging matches the site's paint scheme
    3. To satisfy the crane's maintenance schedule
    4. To catch damage that occurred since the last inspection Correct answer.

    Explanation

    Rigging can be damaged between periodic inspections by the previous lift, transport, or storage. Frequent pre-use inspection catches new damage before it is loaded.

  37. Question 37Inspect rigging before use

    A rigger finds a shackle whose pin is bent and cannot be fully seated. What is the correct action?

    1. Use the shackle with the pin partly engaged
    2. Substitute a bolt of similar diameter
    3. Tighten the pin with a wrench until it seats
    4. Remove the shackle from service Correct answer.

    Explanation

    A bent pin cannot fully engage the shackle body, so the assembly cannot carry its rated load. The shackle must be removed from service, and substituting hardware is not permitted.

  38. Question 38Inspect rigging before use

    When inspecting a chain sling, which finding is a removal-from-service criterion?

    1. Normal surface oxidation that wipes off
    2. A legible capacity tag attached to the master link
    3. A link stretched so that it no longer matches the pitch of adjacent links Correct answer.
    4. A light film of lubricant on the links

    Explanation

    A link that has stretched or elongated has been overloaded and has permanently deformed, so the chain no longer has predictable strength. Stretch is a removal criterion.

  39. Question 39Inspect rigging before use

    A wire rope sling shows a kink where strands are permanently displaced and the rope diameter is reduced at that point. Why is this a removal criterion?

    1. It creates a weak point and disturbs load sharing among strands Correct answer.
    2. It changes the rope's color
    3. It shortens the sling's overall length
    4. It makes the sling easier to handle

    Explanation

    A kink with permanently displaced strands means the rope's structure is distorted, so strands no longer share load evenly and a weak point exists. The sling must be removed from service.

  40. Question 40Inspect rigging before use

    Before use, what should the rigger confirm about the attachment point on the load itself?

    1. That it is painted the same color as the sling
    2. That it was installed by the crane operator
    3. That it is sound and adequate for the intended load Correct answer.
    4. That it is located at the load's center of gravity

    Explanation

    The load's attachment point must be strong enough and in sound condition to accept the load, or the lift can fail regardless of sling condition. The rigger verifies the point as part of the pre-use check.

  41. Question 41Inspect rigging before use

    A rigger is inspecting a synthetic sling and finds a broken stitch in the load-bearing splice area. What does this indicate?

    1. The splice may be failing and the sling should be removed Correct answer.
    2. The stitch is decorative and can be ignored
    3. The sling is new and unused
    4. The sling should be used at reduced capacity

    Explanation

    Stitching in a splice carries or secures the load path; broken stitching in that area suggests the splice is coming apart. The sling must be removed from service rather than derated.

  42. Question 42Inspect rigging before use

    Which inspection finding on a master link or end link of a chain sling requires the assembly to be removed from service?

    1. A slight sheen from recent lubrication
    2. A small amount of dust in the link opening
    3. A capacity tag that is clean and legible
    4. A crack visible at the weld or shoulder Correct answer.

    Explanation

    A crack in a master link or end link can propagate and cause sudden failure of the entire assembly. Cracks are always a removal criterion.

  43. Question 43Inspect rigging before use

    A rigger finds a hook with a missing or broken latch (safety clip). How should this be handled?

    1. Use the hook if the load is below half capacity
    2. Remove the hook from service until the latch is replaced Correct answer.
    3. Tie the load with wire to keep it in the hook
    4. Use the hook only for vertical lifts

    Explanation

    A functioning latch keeps the load from slipping out of the hook, and a missing or broken latch is a defect. The hook must be removed from service until the latch is properly replaced.

  44. Question 44Inspect rigging before use

    A rigger is choosing between two shackles of the same size, one marked with its rated load and one unmarked. What is the correct decision?

    1. Use the unmarked one because size determines capacity
    2. Use the unmarked one only for light loads
    3. Use the marked one because its capacity can be verified Correct answer.
    4. Use either one because both are the same size

    Explanation

    Only marked hardware has a manufacturer-verified rating the rigger can compare to the load. Same size does not guarantee the same material or rating.

  45. Question 45Inspect rigging before use

    A synthetic web sling has a tag showing capacity, but a section of webbing is faded and has a powdery surface. What is the most likely cause and the correct action?

    1. Ultraviolet degradation; remove from service Correct answer.
    2. Normal wear; return to service
    3. Water staining; dry and use
    4. Paint overspray; wipe and use

    Explanation

    Fading with a powdery surface on synthetic webbing is characteristic of ultraviolet degradation, which breaks down the fibers and reduces strength. The sling must be removed from service.

  46. Question 46Inspect rigging before use

    A rigger inspects a wire rope sling and finds the rope has a birdcage (strands forced outward from the core). What is the correct disposition?

    1. Return it to service if the outer strands look intact
    2. Shorten the sling to bypass the birdcage
    3. Remove it from service Correct answer.
    4. Use it only in a choker hitch

    Explanation

    A birdcage shows the rope's structure has been disturbed and the core and strands no longer share load as designed. It is a removal criterion regardless of outward appearance.

  47. Question 47Inspect rigging before use

    Two chain slings look identical, but one has a tag showing a lower working load limit than the other. What is the most likely explanation a rigger should consider?

    1. The lower-rated chain has a smaller link size or different grade Correct answer.
    2. The tag on the lower-rated chain is always wrong
    3. Chain capacity depends only on the number of legs
    4. The higher-rated chain is always newer

    Explanation

    Working load limit depends on link size, chain grade, and configuration, so visually similar chains can have different ratings. The rigger must rely on the tag and verify it matches the chain.

  48. Question 48Inspect rigging before use

    A rigger finds a synthetic round sling whose cover is intact but whose core feels lumpy and uneven along its length. What does this indicate?

    1. The core fibers may be damaged or bunched, so remove it from service Correct answer.
    2. The sling should be used at reduced capacity
    3. The sling is properly broken in
    4. The cover is too tight for the core

    Explanation

    The core carries the load in a round sling, and lumpy or uneven feel suggests damaged, bunched, or broken core fibers. Because the core cannot be seen, the sling must be removed from service.

  49. Question 49Inspect rigging before use

    A rigger is inspecting a wire rope sling and finds severe corrosion with pitting over much of its length. Why does pitting matter more than uniform surface rust?

    1. Pitting reduces the cross section locally and creates stress concentrations Correct answer.
    2. Pitting changes the rope's lay direction
    3. Pitting only affects the rope's color
    4. Pitting makes the rope stiffer and stronger

    Explanation

    Pitting removes metal at discrete points and creates stress concentrations where failure can start, so it is more serious than uniform surface oxidation. Severe pitting is a removal criterion.

  50. Question 50Inspect rigging before use

    A rigger finds a chain sling with a leg that has been repaired by welding a cracked link. What is the correct disposition?

    1. Use it only if the weld is painted over
    2. Return it to service if the weld looks sound
    3. Remove it from service because field welding is not permitted Correct answer.
    4. Use it only for loads below half capacity

    Explanation

    Chain links are heat-treated, and field welding alters their properties and is not an approved repair. A welded or repaired link makes the sling unfit for service.

  51. Question 51Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    In a vertical hitch, the load is carried entirely by which part of the sling assembly?

    1. The single leg or eye-to-eye sling hanging straight down Correct answer.
    2. The hardware at the hook only
    3. The choke point where the sling wraps the load
    4. The basket formed around the load

    Explanation

    A vertical hitch hangs straight from the hook to the attachment point, so the full rated capacity of the sling leg is available. There is no angle or wrap that reduces capacity.

  52. Question 52Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    How many parts of sling support the load in a single basket hitch?

    1. One
    2. Three
    3. Four
    4. Two Correct answer.

    Explanation

    A basket hitch passes the sling under the load so two parts of the sling share the load. The rated capacity is based on two legs, subject to angle and wrap considerations.

  53. Question 53Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What happens to the rated capacity of a sling when it is used in a choker hitch compared with a vertical hitch?

    1. Capacity increases because the load is gripped
    2. Capacity stays the same because the sling is the same
    3. Capacity is unaffected by the wrap angle
    4. Capacity decreases because of the bend and compression Correct answer.

    Explanation

    A choker hitch reduces capacity because the sling bends sharply around itself and the load, creating stress concentration. The choke angle and hardware further reduce the effective strength.

  54. Question 54Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which knot is commonly used to tie off a tag line or secure a light load and is valued for being easy to untie after loading?

    1. Square knot
    2. Clove hitch
    3. Bowline Correct answer.
    4. Figure-eight knot

    Explanation

    The bowline forms a fixed loop that does not slip or bind under load and is easily untied afterward. It is a standard utility knot for rigging tag lines and light securing.

  55. Question 55Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A sling is rigged in a two-leg bridle at a 60-degree angle from horizontal. Compared with a single vertical leg, the capacity of each leg at that angle is:

    1. Unchanged from its vertical rating
    2. Reduced by the angle factor Correct answer.
    3. Doubled to account for two legs
    4. Greater than its vertical rating

    Explanation

    As the angle from horizontal decreases, the tension in each leg increases for the same load, so the usable capacity of each leg is reduced by the angle factor. A 60-degree angle reduces capacity compared with vertical.

  56. Question 56Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the primary purpose of a tag line during a lift?

    1. To attach the load to the hook
    2. To measure the weight of the load
    3. To control load rotation and keep personnel clear Correct answer.
    4. To increase the lifting capacity of the crane

    Explanation

    A tag line lets a rigger guide and steady a load from a safe distance, controlling rotation and swing. It is never used to add capacity or as part of the load-bearing connection.

  57. Question 57Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    When selecting shackles for a lift, the rated capacity marked on the shackle applies to which loading direction?

    1. Perpendicular to the pin only
    2. Only when the pin is fully tightened by hand
    3. Along the bow only, in line with the pin Correct answer.
    4. Any direction equally

    Explanation

    A screw-pin or bolt-type shackle is rated for a load applied along the bow, in line with the pin. Side loading the shackle reduces its capacity and is not covered by the rating.

  58. Question 58Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A load weighs 4,000 lb and is lifted with a two-leg bridle at a 45-degree angle from horizontal. What is the approximate tension in each leg?

    1. 4,000 lb
    2. 2,828 lb Correct answer.
    3. 5,657 lb
    4. 2,000 lb

    Explanation

    Each leg tension equals half the load divided by the sine of the angle from horizontal. Half the load is 2,000 lb, and 2,000 divided by sin 45 degrees (0.707) is about 2,828 lb per leg.

  59. Question 59Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What does the term D/d ratio describe in rigging?

    1. The ratio of the diameter of the bend to the sling body diameter Correct answer.
    2. The ratio of hook opening to sling width
    3. The ratio of shackle diameter to pin diameter
    4. The ratio of load weight to sling capacity

    Explanation

    The D/d ratio compares the diameter of the object or hardware a sling bends around (D) to the sling's body diameter (d). A small D/d ratio means a tighter bend and reduces sling efficiency.

  60. Question 60Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which condition most reduces the strength of a wire rope sling?

    1. Storage on a properly sized reel
    2. A gentle bend around a large-diameter pin
    3. A sharp bend around a small-diameter edge Correct answer.
    4. Use in a straight vertical lift

    Explanation

    Wire rope loses strength when bent around a radius that is small relative to its diameter because outer wires are overstressed. Sharp edges and small D/d ratios concentrate stress and can crush or kink the rope.

  61. Question 61Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A sling has a tag showing a rated capacity, but the tag is faded and unreadable. What should the rigger do?

    1. Estimate the capacity from the sling color
    2. Assume the capacity equals the hook rating
    3. Use the sling at half of the estimated capacity
    4. Remove the sling from service until capacity is verified Correct answer.

    Explanation

    A sling without a legible capacity tag cannot be safely rated, so it must be removed from service until identified and verified. Guessing capacity is never acceptable for a lift.

  62. Question 62Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the effect of a basket hitch on a load with two vertical legs compared with a single choker hitch of the same sling?

    1. The basket capacity depends only on the hook
    2. The basket generally provides greater capacity because two parts share the load Correct answer.
    3. The basket provides less capacity because the sling is doubled
    4. The two hitches have identical capacity

    Explanation

    In a basket hitch two parts of the sling support the load, so capacity is generally higher than a single choker, where one part is bent and compressed. The actual capacity still depends on the angle and D/d ratio.

  63. Question 63Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which hardware item is designed to connect a sling to a load while allowing the sling to align with the load direction?

    1. Wire rope clip
    2. Spreader beam
    3. Swivel hoist ring Correct answer.
    4. Come-along

    Explanation

    A swivel hoist ring pivots and rotates so the sling stays aligned with the load, reducing side loading. It is a common attachment point for rigging.

  64. Question 64Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Why should the angle of a two-leg sling be kept as steep (close to vertical) as practical?

    1. Steeper angles increase the tension in each leg
    2. Steeper angles reduce the tension in each leg for the same load Correct answer.
    3. Steeper angles reduce the load weight
    4. Steeper angles eliminate the need for shackles

    Explanation

    As legs approach vertical, the angle factor approaches one, so less tension is required in each leg to support the same load. Flatter angles multiply leg tension and reduce usable capacity.

  65. Question 65Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the main risk of using a single wrap choker hitch on a smooth, cylindrical load?

    1. The sling may slip and the load may rotate or slide out Correct answer.
    2. The sling capacity increases unexpectedly
    3. The hook will open automatically
    4. The load weight doubles

    Explanation

    A single choker on a smooth cylinder provides limited grip, so the load can slip or rotate. Additional wraps or a different hitch may be needed to control the load.

  66. Question 66Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which factor must be considered when choosing between a synthetic web sling and a wire rope sling for a lift?

    1. Wire rope is preferred near sharp edges without protection
    2. Wire rope is required for all outdoor lifts
    3. Synthetic slings resist cuts and abrasion better than wire rope
    4. Synthetic slings are lighter and less likely to damage finished surfaces Correct answer.

    Explanation

    Synthetic web slings are lighter and softer, making them suitable where contact damage to the load must be avoided. They are more vulnerable to cuts and abrasion, so edge protection is important.

  67. Question 67Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What does the term 'sling protection' refer to in rigging?

    1. Painting the sling to identify capacity
    2. Storing slings in a protected cabinet
    3. Using pads or softeners at contact points to prevent damage Correct answer.
    4. Covering the hook with a guard

    Explanation

    Sling protection means placing pads, softeners, or edge guards between the sling and sharp or abrasive contact points. This prevents cuts and bends that reduce sling strength.

  68. Question 68Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A rigger needs a knot that will not slip when joining two ropes of the same diameter for a light utility task. Which is the most appropriate choice?

    1. Clove hitch
    2. Square knot (reef knot) Correct answer.
    3. Bowline
    4. Timber hitch

    Explanation

    The square knot is intended to join two ropes of equal diameter and holds reasonably for light utility use. It should not be relied on for critical overhead lifting.

  69. Question 69Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the purpose of a spreader beam in a lifting arrangement?

    1. To reduce the weight of the load
    2. To keep sling legs vertical and avoid load compression Correct answer.
    3. To increase the crane's boom length
    4. To replace the need for a hook

    Explanation

    A spreader beam holds sling legs apart so they stay closer to vertical, reducing leg tension and preventing inward compression on the load. It helps protect loads that could be crushed.

  70. Question 70Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which of the following is a correct practice when attaching a sling to a crane hook?

    1. Allow the sling eyes to bunch at the hook tip
    2. Load the hook tip only
    3. Hang the sling on the hook latch
    4. Seat the sling in the bowl of the hook with the latch closed Correct answer.

    Explanation

    Slings should be seated in the bowl of the hook so the load is centered, and the latch should be closed to retain the sling. Loading the tip or latch can cause slippage or hook damage.

  71. Question 71Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What does the working load limit (WLL) of a rigging component represent?

    1. The weight of the component itself
    2. The load at which the component will break
    3. The load at which the component begins to deform permanently
    4. The maximum load the component should carry in service Correct answer.

    Explanation

    The working load limit is the maximum load a component is rated to carry in normal service, derived by applying a design factor to its breaking strength. Exceeding the WLL reduces the safety margin.

  72. Question 72Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A three-leg bridle supports a load that is not symmetric, so one leg carries most of the weight. Which statement is true?

    1. Only two legs ever carry load in a three-leg bridle
    2. The load is always shared equally by all three legs
    3. Capacity depends only on the total load weight
    4. The heaviest-loaded leg governs the safe capacity of the assembly Correct answer.

    Explanation

    In an asymmetric bridle the load is not shared equally, and the leg carrying the most tension is the limiting factor. Rigs should be designed so no single leg is overloaded.

  73. Question 73Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which of these is a warning sign that a synthetic web sling should be removed from service?

    1. Storage in a clean, dry location
    2. A slight uniform color from normal use
    3. A legible capacity tag attached at the eye
    4. Cuts, burns, or melted fibers on the webbing Correct answer.

    Explanation

    Cuts, burns, melting, and broken fibers indicate damage that reduces sling strength, so the sling must be removed from service. A legible tag and proper storage are signs of a serviceable sling.

  74. Question 74Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the function of a come-along in rigging?

    1. To lift loads overhead
    2. To pull or tension a load over a short distance Correct answer.
    3. To measure sling tension
    4. To connect the hook to the load

    Explanation

    A come-along is a hand-operated pulling tool used to tension or move a load a short distance. It is not a lifting device for overhead loads.

  75. Question 75Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A load is lifted with a two-leg bridle at 30 degrees from horizontal. Compared with the same load at 60 degrees, the tension in each leg will be:

    1. Zero because the legs cancel out
    2. Lower because the legs are flatter
    3. The same because the load is unchanged
    4. Higher because the flatter angle increases leg tension Correct answer.

    Explanation

    Flatter sling angles increase the tension required in each leg to support the same vertical load. At 30 degrees the angle factor is larger, so leg tension is higher than at 60 degrees.

  76. Question 76Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which knot is formed by a loop that will not tighten under load and is commonly tied at the end of a rope to provide a secure attachment point?

    1. Sheet bend
    2. Timber hitch
    3. Clove hitch
    4. Bowline Correct answer.

    Explanation

    A bowline creates a fixed loop at the end of a rope that holds its size under load and unties easily after being loaded. The other knots listed either tighten, wrap around an object, or join two ropes.

  77. Question 77Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A choker hitch differs from a vertical hitch primarily in that the choker hitch:

    1. grips and constricts the load as tension is applied Correct answer.
    2. transfers load to the hardware rather than the sling
    3. requires the sling to pass under the load twice
    4. distributes load across two legs of equal tension

    Explanation

    In a choker hitch the sling passes around the load and back through itself, so tension causes it to constrict and grip the load. This constriction reduces the sling's capacity compared with a vertical hitch.

  78. Question 78Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A basket hitch is formed when a sling:

    1. wraps around the load and passes back through its own eye
    2. passes under the load and both ends attach to the hook Correct answer.
    3. is attached to the load at a single point with one leg
    4. is wrapped twice around the load and both eyes attach to the hook

    Explanation

    A basket hitch cradles the load with the sling passing beneath it and both ends going to the hook. With two vertical legs it can support roughly twice the load of a single vertical leg, provided the load is balanced.

  79. Question 79Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which component is used between the crane hook and the sling eyes to gather multiple legs at a single point?

    1. Swivel
    2. Master link Correct answer.
    3. Spreader beam
    4. Shackle

    Explanation

    A master link or master ring is the assembly that collects the legs of a multi-leg sling so they meet at one connection point at the hook. Shackles connect individual components, and spreader beams keep legs apart.

  80. Question 80Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    When a sling is used in a vertical hitch, the load is carried:

    1. by constriction of the sling around the load
    2. by friction between the sling and the load surface
    3. by compression of the sling against the load
    4. by the sling body in direct tension between hook and load Correct answer.

    Explanation

    A vertical hitch carries the load in straight tension through the sling body from the hook to the attachment point. This is the most efficient hitch configuration because there is no angle or constriction loss.

  81. Question 81Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the main purpose of a double wrap choker when handling a smooth cylindrical load?

    1. To eliminate the need for a tag line
    2. To allow the load to rotate freely during the lift
    3. To double the rated capacity of the sling
    4. To increase grip and reduce the chance of the load slipping Correct answer.

    Explanation

    A double wrap places two turns of sling around the load so friction and contact area increase, reducing slip on smooth surfaces. It also distributes pressure, but it does not increase the sling's rated capacity.

  82. Question 82Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which knot is best suited for temporarily attaching a rope to a cylindrical object such as a pipe for a light utility pull?

    1. Bowline
    2. Figure-eight knot
    3. Sheet bend
    4. Clove hitch Correct answer.

    Explanation

    A clove hitch wraps around an object and tightens when loaded, making it useful for quick attachment to pipes or posts. It is easily adjusted and untied after use.

  83. Question 83Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A two-leg bridle supports a load with each leg at 60 degrees from horizontal. If the load is 2,000 lb and evenly balanced, what is the approximate tension in each leg?

    1. 1,000 lb
    2. 500 lb
    3. 1,155 lb Correct answer.
    4. 2,000 lb

    Explanation

    Each leg carries half the vertical load divided by the sine of the angle from horizontal. Half the load is 1,000 lb, and 1,000 divided by sin 60 degrees (0.866) equals about 1,155 lb per leg.

  84. Question 84Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A single-leg choker hitch has a rated capacity of 3,200 lb in a vertical configuration. If the same sling is used in a choker hitch, its capacity is generally:

    1. reduced compared with the vertical hitch rating Correct answer.
    2. increased because the load is gripped
    3. equal to the vertical hitch rating
    4. unaffected by hitch type

    Explanation

    Choker hitches reduce a sling's capacity because the sling is bent back through its own eye and grips the load, concentrating stress. Manufacturers publish separate capacities for vertical, choker, and basket configurations.

  85. Question 85Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A load is supported by a two-leg bridle at 45 degrees from horizontal. If each leg is rated 5,000 lb, what is the approximate maximum vertical load the arrangement can safely support, assuming equal leg tension?

    1. 5,000 lb
    2. 3,535 lb
    3. 10,000 lb
    4. 7,070 lb Correct answer.

    Explanation

    The vertical component of each leg equals the leg tension times the sine of the angle from horizontal. Each leg contributes 5,000 times 0.707, or about 3,535 lb, so two legs support about 7,070 lb.

  86. Question 86Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    When using a basket hitch on a load, the sling legs should be kept:

    1. at any angle because basket capacity is constant
    2. at exactly 45 degrees from horizontal
    3. as horizontal as practical to spread the load
    4. as close to vertical as practical to maximize capacity Correct answer.

    Explanation

    Basket hitch capacity depends on the angle between the legs; steeper legs keep more of the tension vertical and preserve capacity. As legs approach horizontal, tension rises sharply for the same vertical load.

  87. Question 87Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which condition would most likely require removing a synthetic web sling from service?

    1. A light dusting of dirt on the cover
    2. A manufacturer's tag that is legible but slightly curled
    3. A deep cut or burn that exposes the inner load-bearing fibers Correct answer.
    4. Fading of the sling's color from sunlight

    Explanation

    Cuts, burns, or abrasion that expose or sever load-bearing fibers compromise the sling's strength and require removal. Fading, surface dirt, and a legible tag do not by themselves indicate loss of strength.

  88. Question 88Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A rigger must join two ropes of different diameters for a light utility task. Which knot is appropriate?

    1. Timber hitch
    2. Bowline
    3. Sheet bend Correct answer.
    4. Clove hitch

    Explanation

    A sheet bend is designed to join two ropes and works even when the ropes differ in diameter, with the larger rope forming the bight. The other knots listed form loops or attach to objects rather than joining ropes.

  89. Question 89Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A sling is attached to a load with a shackle, and the shackle pin is bearing against a sharp edge of the load. What is the best corrective action?

    1. Replace the shackle with a hook
    2. Reposition the shackle or add protection so the pin is not side-loaded or damaged Correct answer.
    3. Tighten the pin further to resist the edge
    4. Continue the lift because shackle pins are hardened

    Explanation

    Shackle pins are not designed for side loading or contact with sharp edges, which can bend or damage the pin and cause failure. Repositioning the shackle or adding edge protection keeps the load in the intended direction.

  90. Question 90Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    What is the effect of increasing the number of wraps of a wire rope sling around a load before making a choker?

    1. The sling's D/d ratio becomes irrelevant
    2. The choker angle no longer affects capacity
    3. Rated capacity of the sling increases beyond its tag value
    4. Grip improves and pressure on the load is spread over more contact area Correct answer.

    Explanation

    Additional wraps increase friction and distribute contact pressure, improving grip and reducing damage to the load. The sling's rated capacity is still governed by the manufacturer's tag and hitch configuration.

  91. Question 91Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A load is lifted with a two-leg bridle at 30 degrees from horizontal. If the load is 3,000 lb and evenly balanced, what is the approximate tension in each leg?

    1. 1,500 lb
    2. 1,732 lb
    3. 3,000 lb Correct answer.
    4. 2,598 lb

    Explanation

    Each leg carries half the load vertically, which is 1,500 lb, divided by sin 30 degrees (0.5). That gives about 3,000 lb of tension per leg, showing how sharply tension rises at shallow angles.

  92. Question 92Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which statement about the working load limit of a sling in a basket hitch with two vertical legs is correct?

    1. It is always equal to the single-leg vertical rating
    2. It is independent of the number of legs
    3. It can approach twice the single-leg vertical rating if the load is balanced and legs are vertical Correct answer.
    4. It is always half the single-leg vertical rating

    Explanation

    A basket hitch with two vertical legs shares the load between two sling sections, so capacity can approach twice the single-leg vertical rating when the load is balanced. Angling the legs away from vertical reduces this advantage.

  93. Question 93Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A tag line is used during a lift primarily to:

    1. control load rotation and sway from a safe distance Correct answer.
    2. measure the weight of the load
    3. increase the lifting capacity of the crane
    4. provide a backup attachment in case the sling fails

    Explanation

    A tag line lets a rigger guide and steady the load without standing under it or touching it directly. It does not add capacity or serve as a backup attachment.

  94. Question 94Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A sling eye is placed directly on a crane hook that has a sharp throat edge. What is the recommended practice?

    1. Use a softener or hook with a rounded throat so the eye is not cut Correct answer.
    2. Reduce the load to half and proceed
    3. Force the eye fully into the throat to spread the load
    4. Attach the eye to the hook tip only

    Explanation

    Sharp hook throats can cut or abrade sling eyes, so a softener or a hook with a properly rounded throat protects the sling. Sling eyes should sit in the bowl of the hook, not on the tip.

  95. Question 95Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Why is a choker hitch often preferred over a vertical hitch for lifting a bundle of loose pipes?

    1. The choker increases the rated capacity of the sling
    2. The choker allows the bundle to spread during the lift
    3. The choker constricts and grips the bundle to help keep it together Correct answer.
    4. The choker eliminates the need for a tag line

    Explanation

    A choker hitch tightens around the bundle as tension is applied, helping hold loose items together during the lift. This gripping action is useful even though choker capacity is lower than vertical capacity.

  96. Question 96Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A load is supported by a three-leg bridle, but because of an off-center center of gravity, one leg carries most of the weight. Which statement is correct?

    1. The most heavily loaded leg governs the safe capacity of the arrangement Correct answer.
    2. The two lightly loaded legs can be ignored in capacity calculations
    3. The load is shared equally among all three legs regardless of balance
    4. The arrangement is safe as long as the total load is below the sum of all leg ratings

    Explanation

    When a load is unbalanced, the leg carrying the greatest share can be overloaded even if the total load seems acceptable. The capacity of the arrangement is therefore limited by the most heavily loaded leg.

  97. Question 97Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A two-leg bridle is used at a shallow angle from horizontal. Compared with a steeper bridle supporting the same load, the shallow bridle will:

    1. produce lower tension in each leg and less compression on the load
    2. produce higher tension in each leg and greater horizontal compression on the load Correct answer.
    3. reduce the total vertical force required
    4. produce the same tension because the load is unchanged

    Explanation

    As the angle from horizontal decreases, each leg must carry a larger tension to provide the same vertical component, and the horizontal components squeeze the load harder. This is why shallow sling angles are avoided.

  98. Question 98Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A wire rope sling is bent around a load with a very small radius. What is the primary concern?

    1. The sling will lengthen and change the load angle
    2. Bending stress reduces the sling's strength compared with a larger radius Correct answer.
    3. The load will become lighter as it is lifted
    4. The sling's color coding will no longer be valid

    Explanation

    Bending wire rope around a small radius creates high bending stress and reduces strength, which is why D/d ratio matters. Larger radii distribute the bend and preserve more of the sling's capacity.

  99. Question 99Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    Which combination of hitch and hardware best minimizes the chance of a sling eye slipping off a hook during a lift?

    1. A single sling eye placed loosely over an open hook tip
    2. A sling eye resting on the hook latch
    3. A shackle connecting the sling eye to a closed hook or master link Correct answer.
    4. A sling eye hooked over the tip with the latch open

    Explanation

    Closing the connection with a shackle or master link keeps the sling eye captured and prevents it from slipping off the hook. Relying on an open hook or the latch alone does not provide a secure connection.

  100. Question 100Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots

    A rigger is choosing between a choker hitch and a basket hitch for a long, rigid load that must not be squeezed. Which choice is appropriate and why?

    1. Basket hitch, because it cradles the load without constricting it Correct answer.
    2. Choker hitch, because it has higher capacity than a basket
    3. Either hitch, because both squeeze the load equally
    4. Choker hitch, because it grips the load tightly

    Explanation

    A basket hitch supports the load from beneath without constricting it, which suits loads that could be damaged by squeezing. A choker tightens around the load and can crush or deform it.

  101. Question 101Recognize associated hazards

    What is the primary hazard of working near overhead power lines during a lift?

    1. Excessive noise that can damage hearing
    2. Vibration that can loosen rigging
    3. Dust that can reduce visibility
    4. Electrical contact that can cause shock or electrocution Correct answer.

    Explanation

    Overhead power lines present a serious electrocution hazard if the crane, load, or rigging contacts them or comes too close. Electricity can arc across air gaps, so direct contact is not required for a shock to occur.

  102. Question 102Recognize associated hazards

    When rigging a load, what is the primary purpose of using softeners or edge protectors on slings?

    1. To reduce the overall weight of the load
    2. To make the sling easier to inspect
    3. To protect the sling from sharp edges and abrasion Correct answer.
    4. To increase the sling's lifting capacity

    Explanation

    Softeners or edge protectors are placed between the sling and sharp or abrasive load edges to prevent cutting, wear, and damage that could lead to sling failure. They do not increase capacity or change the load weight.

  103. Question 103Recognize associated hazards

    What is the main danger of a load swinging unexpectedly during a lift?

    1. It can increase the crane's lifting capacity
    2. It can strike nearby personnel or structures Correct answer.
    3. It can cause the crane's hydraulic oil to overheat
    4. It can reduce the load's weight

    Explanation

    An uncontrolled swing can cause the load to impact workers, equipment, or structures, leading to injuries and damage. Swing also creates dynamic forces that can overload the crane or rigging.

  104. Question 104Recognize associated hazards

    Why is it important to keep the load as close to the crane's center of rotation as possible during a lift?

    1. To increase the lifting speed
    2. To minimize the load moment and reduce the risk of tipping Correct answer.
    3. To make the load easier to see
    4. To reduce the load's weight

    Explanation

    The load moment is the product of the load weight and the radius from the crane's center of rotation. Keeping the load close reduces the moment, which decreases the risk of tipping and structural overload.

  105. Question 105Recognize associated hazards

    What should a rigger do if a load appears to be unbalanced or shifting during a lift?

    1. Continue the lift slowly
    2. Quickly adjust the rigging while the load is suspended
    3. Ignore it if the load is not too heavy
    4. Signal the operator to stop and lower the load Correct answer.

    Explanation

    An unbalanced or shifting load indicates a potential loss of control. The safest action is to stop the lift and lower the load to the ground so it can be re-rigged or inspected.

  106. Question 106Recognize associated hazards

    What is a common hazard associated with the use of synthetic web slings?

    1. They cannot be used in cold weather
    2. They are electrically conductive
    3. They are prone to damage from ultraviolet light and chemicals Correct answer.
    4. They are the heaviest type of sling

    Explanation

    Synthetic web slings can degrade when exposed to ultraviolet light, chemicals, or heat, which weakens the fibers and reduces strength. They are also susceptible to cuts and abrasion.

  107. Question 107Recognize associated hazards

    When using a shackle in a lifting application, what is the primary hazard if the shackle pin is not fully seated and secured?

    1. The load may become lighter
    2. The shackle may become too tight to remove
    3. The shackle may become magnetized
    4. The pin may back out, causing the shackle to fail Correct answer.

    Explanation

    If the shackle pin is not fully seated and secured, vibration or load movement can cause it to back out, leading to separation of the shackle and dropping the load. Always ensure the pin is fully engaged and secured.

  108. Question 108Recognize associated hazards

    What is the primary hazard of using a hook with a damaged safety latch?

    1. The load may slip off the hook Correct answer.
    2. The hook may rotate too freely
    3. The hook may become too heavy
    4. The hook may become electrically charged

    Explanation

    The safety latch prevents slings or lines from slipping off the hook when the load is slack or during lifting. A damaged latch increases the risk of the load slipping off and falling.

  109. Question 109Recognize associated hazards

    What is the purpose of a tag line during a lift?

    1. To control the load and prevent rotation Correct answer.
    2. To measure the weight of the load
    3. To provide extra lifting height
    4. To increase the lifting capacity of the crane

    Explanation

    Tag lines are used to control the load's orientation and prevent unwanted rotation or swinging, especially when the load is large or has a high profile. They help keep the load and personnel out of harm's way.

  110. Question 110Recognize associated hazards

    What is a key hazard when lifting a load with multiple slings that form an angle greater than 90 degrees at the hook?

    1. The slings may become too long
    2. The load may become lighter
    3. The hook may become too cold
    4. The tension in each sling increases, reducing capacity Correct answer.

    Explanation

    As the angle between sling legs increases, the tension in each leg increases for the same load weight, which can reduce the overall lifting capacity and overload the slings. Keeping the angle at 90 degrees or less is generally recommended.

  111. Question 111Recognize associated hazards

    Why is it dangerous to leave a suspended load unattended?

    1. The rigging may become stronger
    2. The load may become lighter over time
    3. The load could drift or fall if the crane fails Correct answer.
    4. The crane may automatically lower the load

    Explanation

    An unattended suspended load is at risk of moving due to wind, creep, or hydraulic failure, and could fall if the lifting system fails. Personnel must never leave a suspended load unattended.

  112. Question 112Recognize associated hazards

    What is the primary hazard of working on a suspended load?

    1. The rigging may become tangled
    2. The load could move or fall, causing injury Correct answer.
    3. The crane may tip over backwards
    4. The load may become too heavy

    Explanation

    Working on or under a suspended load is extremely hazardous because the load could shift, the rigging could fail, or the crane could malfunction, leading to serious injury or death. Personnel should never be under a suspended load.

  113. Question 113Recognize associated hazards

    What is the main concern when lifting a load in high winds?

    1. The wind can cause the load to swing or rotate, reducing control Correct answer.
    2. The crane's engine may overheat
    3. The rigging may shrink
    4. The load may become lighter

    Explanation

    High winds can exert force on the load and crane, causing the load to swing, rotate, or drift, which can lead to loss of control and impact with structures or personnel. Lifts should be postponed or carefully planned in windy conditions.

  114. Question 114Recognize associated hazards

    What is a common hazard when using a chain sling that has been improperly stored?

    1. The chain may lose its color
    2. The chain may become magnetized
    3. The chain may become too flexible
    4. The chain may have hidden cracks or corrosion Correct answer.

    Explanation

    Improper storage can lead to corrosion, cracking, or other damage that weakens the chain and may not be immediately visible. Chain slings should be inspected before each use and stored properly to prevent damage.

  115. Question 115Recognize associated hazards

    What is the primary hazard of using a crane near an excavation or trench?

    1. The load may become lighter
    2. The crane's boom may become too short
    3. The excavation may fill with water
    4. The crane may sink or tip if the ground is unstable Correct answer.

    Explanation

    Excavations can reduce ground support near the crane's outriggers or tracks, leading to settlement, tipping, or collapse. Cranes must be set up on stable ground at a safe distance from excavations.

  116. Question 116Recognize associated hazards

    Why is it important to avoid sudden starts and stops when operating a crane?

    1. To save fuel
    2. To reduce noise
    3. To prevent dynamic loads that can overload the crane or rigging Correct answer.
    4. To keep the load from becoming lighter

    Explanation

    Sudden starts and stops create dynamic forces (shock loads) that can exceed the static weight of the load and overload the crane or rigging. Smooth operation helps maintain control and reduces stress on the equipment.

  117. Question 117Recognize associated hazards

    What is a key hazard when using a spreader beam that is not rated for the load?

    1. The beam may fail structurally, dropping the load Correct answer.
    2. The beam may become magnetic
    3. The beam may rotate too easily
    4. The beam may become too light

    Explanation

    Using a spreader beam beyond its rated capacity can cause it to bend, crack, or fail, leading to loss of the load. Always verify the beam's rated capacity and ensure it is suitable for the lift.

  118. Question 118Recognize associated hazards

    What is the primary hazard of lifting a load that has an unknown center of gravity?

    1. The rigging may become too short
    2. The load may tilt or rotate unexpectedly Correct answer.
    3. The crane may become unstable
    4. The load may become heavier

    Explanation

    If the center of gravity is not known, the load may not hang level and could tilt or rotate when lifted, causing loss of control and potential injury. Always determine the center of gravity and rig accordingly.

  119. Question 119Recognize associated hazards

    What is a common hazard when using a lifting clamp to lift steel plate?

    1. The clamp may become too hot
    2. The clamp may slip if the plate surface is dirty or oily Correct answer.
    3. The clamp may become too heavy
    4. The clamp may lose its color

    Explanation

    Lifting clamps rely on friction and proper engagement with the plate surface. If the surface is dirty, oily, or scaled, the clamp may not grip properly and could slip, dropping the load.

  120. Question 120Recognize associated hazards

    Why is it hazardous to use a wire rope sling that has broken wires or kinks?

    1. The sling may become too flexible
    2. The sling may become magnetic
    3. The sling may become lighter
    4. The sling's strength is reduced and it may fail Correct answer.

    Explanation

    Broken wires and kinks indicate damage that reduces the sling's strength and can lead to sudden failure under load. Wire rope slings should be inspected regularly and removed from service if damaged.

  121. Question 121Recognize associated hazards

    What is the primary hazard of using a crane on a slope?

    1. The rigging may become tangled
    2. The crane may tip over due to reduced stability Correct answer.
    3. The crane's engine may run too fast
    4. The load may become lighter

    Explanation

    Operating a crane on a slope reduces its stability and can cause tipping, especially when lifting or swinging loads. Cranes must be set up on level ground or according to the manufacturer's specifications for slope operation.

  122. Question 122Recognize associated hazards

    What is a critical hazard when performing a tandem lift with two cranes of different capacities?

    1. The rigging may become too short
    2. The cranes may become magnetized
    3. The load may become lighter
    4. The load may shift, causing one crane to be overloaded Correct answer.

    Explanation

    In a tandem lift, the load distribution between cranes can change as the load moves or if the cranes are not synchronized. If one crane takes more than its share, it can be overloaded, leading to tipping or structural failure.

  123. Question 123Recognize associated hazards

    Why is it dangerous to use a sling with a knot tied in it?

    1. The knot reduces the sling's strength significantly Correct answer.
    2. The knot may make the sling too long
    3. The knot may make the sling lighter
    4. The knot may cause the sling to become magnetic

    Explanation

    Knots in slings create stress concentrations and can reduce the sling's strength by as much as 50% or more. Knots also can slip or come untied, leading to load loss.

  124. Question 124Recognize associated hazards

    What is the primary hazard of lifting a load that is partially buried or attached to the ground?

    1. The rigging may become too short
    2. The load may become lighter
    3. The crane may be overloaded due to unanticipated resistance Correct answer.
    4. The load may become magnetic

    Explanation

    If a load is partially buried or attached, additional force is required to free it, which can exceed the crane's capacity and cause overload, tipping, or rigging failure. Always ensure the load is free before lifting.

  125. Question 125Recognize associated hazards

    What is a key hazard when using a crane with a lattice boom near a structure?

    1. The boom may contact the structure and cause damage or collapse Correct answer.
    2. The boom may rotate too easily
    3. The boom may become magnetic
    4. The boom may become too light

    Explanation

    Lattice booms are long and can be difficult to maneuver in tight spaces. Contact with a structure can damage the boom or the structure, potentially causing a collapse or dropping the load.

  126. Question 126Recognize associated hazards

    What is the primary hazard of using a sling with a missing or illegible tag?

    1. The sling may become electrically charged.
    2. The sling may shrink when exposed to sunlight.
    3. The sling may be used beyond its rated capacity. Correct answer.
    4. The sling may corrode faster than tagged slings.

    Explanation

    A missing or illegible tag means the rated capacity and material specifications are unknown, so the rigger cannot verify the sling is adequate for the load. Using an unidentified sling risks overloading and catastrophic failure.

  127. Question 127Recognize associated hazards

    What is a key hazard when using a synthetic sling in an environment where it may contact sharp edges?

    1. The sling may become brittle and shatter.
    2. The sling may be cut or abraded, reducing its strength. Correct answer.
    3. The sling may lose its color.
    4. The sling may become conductive.

    Explanation

    Synthetic slings can be cut or abraded by sharp edges, which reduces their load-bearing capacity and can lead to sudden failure. Protective sleeves or edge guards should be used.

  128. Question 128Recognize associated hazards

    What is the main hazard of using a hook that is twisted or deformed?

    1. The hook may cause the load to rotate.
    2. The hook may become magnetized.
    3. The hook may be difficult to inspect.
    4. The hook may lose its rated capacity and fail under load. Correct answer.

    Explanation

    A twisted or deformed hook has altered geometry that can concentrate stresses and reduce its capacity, leading to failure. Hooks must be inspected and removed from service if deformed.

  129. Question 129Recognize associated hazards

    What is a common hazard when using a chain sling that has been exposed to extreme heat?

    1. The chain may become too flexible.
    2. The chain may lose strength due to heat damage. Correct answer.
    3. The chain may increase in length permanently.
    4. The chain may become non-magnetic.

    Explanation

    High temperatures can alter the metallurgical properties of chain, reducing its strength and making it susceptible to failure. Chain slings must be rated for the temperature of the environment.

  130. Question 130Recognize associated hazards

    What is the primary hazard of using a spreader beam that is not laterally stable?

    1. The beam may become electrically charged.
    2. The beam may attract lightning.
    3. The beam may tip or rotate, causing the load to swing. Correct answer.
    4. The beam may increase the load's weight.

    Explanation

    A spreader beam that lacks lateral stability can tip or rotate during lifting, leading to loss of control of the load. Stability is essential to keep the load level and prevent swinging.

  131. Question 131Recognize associated hazards

    What is a key hazard when using a lifting magnet to lift a load?

    1. The load may be dropped if the magnet's power is interrupted. Correct answer.
    2. The magnet may cause the load to become radioactive.
    3. The magnet may lose power if the load is too light.
    4. The magnet may only lift non-ferrous materials.

    Explanation

    Lifting magnets depend on a continuous power source; if power is interrupted, the magnetic field collapses and the load can drop. Backup power or failsafe designs are often required.

  132. Question 132Recognize associated hazards

    What is the primary hazard of using a sling with a broken or missing identification tag?

    1. The sling may be used at a lower capacity.
    2. The sling may be too short.
    3. The sling may be incorrectly assumed to have a higher capacity. Correct answer.
    4. The sling may become slippery.

    Explanation

    Without a tag, the rated capacity is unknown, and the rigger might assume a higher capacity than the sling actually has, leading to overloading. Always use tagged slings or verify capacity.

  133. Question 133Recognize associated hazards

    What is a common hazard when using a wire rope sling that has been stored improperly and has developed kinks?

    1. Kinks increase the sling's flexibility.
    2. Kinks make the sling lighter.
    3. Kinks can cause uneven load distribution and reduce capacity. Correct answer.
    4. Kinks improve the sling's resistance to abrasion.

    Explanation

    Kinks in wire rope create permanent deformation and can cause uneven stress distribution, reducing the sling's capacity and leading to failure. Kinked slings should be removed from service.

  134. Question 134Recognize associated hazards

    What is the primary hazard of using a crane on soft or uncompacted ground?

    1. The crane's engine may overheat.
    2. The crane's boom may become longer.
    3. The crane may become unstable and tip over. Correct answer.
    4. The crane's tires may wear faster.

    Explanation

    Soft ground can cause the crane's outriggers or tracks to sink, leading to loss of stability and tip-over. Ground conditions must be assessed and mats or cribbing used as needed.

  135. Question 135Recognize associated hazards

    What is a key hazard when lifting a load that is not balanced and may shift during the lift?

    1. The load may change color.
    2. The load may become lighter.
    3. The load may become magnetized.
    4. The load may swing or rotate uncontrollably. Correct answer.

    Explanation

    An unbalanced load can shift its center of gravity during lifting, causing swinging or rotation that can lead to loss of control, injury, or damage. Proper rigging and balance are essential.

  136. Question 136Recognize associated hazards

    What is the main concern when using a basket hitch with a load that has a low coefficient of friction?

    1. The sling may become too tight.
    2. The sling may slip and the load may fall. Correct answer.
    3. The sling may stretch permanently.
    4. The sling may conduct electricity.

    Explanation

    In a basket hitch, friction between the sling and the load helps hold the load. With low friction, the sling can slip, causing the load to drop. Use of friction-enhancing materials or other hitches may be necessary.

  137. Question 137Recognize associated hazards

    What is a critical hazard when performing a lift near overhead power lines?

    1. The crane may become heavier.
    2. The load may become lighter.
    3. The crane or load may contact the lines, causing electrocution. Correct answer.
    4. The power lines may cause the load to rotate.

    Explanation

    Contact with overhead power lines can energize the crane and load, leading to electrocution of personnel. Maintaining the required minimum clearance is essential.

  138. Question 138Recognize associated hazards

    What is the primary hazard of using a sling that is too long for the lift?

    1. The sling may be too strong.
    2. The sling may be difficult to store.
    3. The sling may be overloaded due to increased angle. Correct answer.
    4. The sling may become tangled.

    Explanation

    An excessively long sling can increase the angle between legs, which increases tension in each leg for a given load, potentially overloading the sling. Proper sling length helps maintain safe angles.

  139. Question 139Recognize associated hazards

    What is a common hazard when using a shackle that is side-loaded?

    1. The shackle may become magnetized.
    2. The shackle may become lighter.
    3. The shackle may become more ductile.
    4. The shackle may fail due to reduced capacity. Correct answer.

    Explanation

    Shackles are designed for axial loading; side-loading can significantly reduce their capacity and cause failure. Always load shackles in line with the pin and bow.

  140. Question 140Recognize associated hazards

    What is the main hazard of using a crane with a boom that is not fully extended or retracted properly?

    1. The boom may increase the load's weight.
    2. The boom may collapse or fail structurally. Correct answer.
    3. The boom may attract lightning.
    4. The boom may become electrically charged.

    Explanation

    Improper boom extension can lead to structural instability or failure of the boom. Booms must be operated according to the manufacturer's specifications.

  141. Question 141Recognize associated hazards

    What is a key hazard when lifting a load with slings that are not protected from the load's sharp corners?

    1. The slings may become lighter.
    2. The slings may become stronger.
    3. The slings may become conductive.
    4. The slings may be cut and fail. Correct answer.

    Explanation

    Sharp corners can cut or abrade slings, reducing their strength and leading to failure. Use corner protectors or padding to prevent damage.

  142. Question 142Recognize associated hazards

    What is the primary hazard of using a hoist limit switch as a routine stopping point?

    1. The switch may become more reliable.
    2. The switch may increase the hoist speed.
    3. The switch may reduce the load's weight.
    4. The switch may fail and allow the load to drop. Correct answer.

    Explanation

    Limit switches are emergency devices, not operational stops. Repeated use can cause wear or failure, leading to over-travel and potential load drop. Operators should stop before reaching the limit.

  143. Question 143Recognize associated hazards

    What is a critical hazard when lifting a load that is taller than it is wide?

    1. The load may become magnetized.
    2. The load may change color.
    3. The load may become lighter.
    4. The load may tip over during lifting. Correct answer.

    Explanation

    Tall, narrow loads have a high center of gravity and are prone to tipping, especially if the lift is not vertical or if there is wind. Proper rigging and tag lines help control such loads.

  144. Question 144Recognize associated hazards

    What is the main concern when using a crane near a structure that restricts boom movement?

    1. The crane may become lighter.
    2. The load may become heavier.
    3. The boom may contact the structure, causing damage or collapse. Correct answer.
    4. The crane may become more efficient.

    Explanation

    Restricted boom movement near a structure increases the risk of contact, which can damage the structure or crane and cause loss of control. Proper planning and clearance are essential.

  145. Question 145Recognize associated hazards

    What is a key hazard of using a sling with a tag that is not legible?

    1. The sling may become slippery.
    2. The sling may become electrically charged.
    3. The sling may be used beyond its capacity. Correct answer.
    4. The sling may become too short.

    Explanation

    An illegible tag prevents verification of the sling's capacity and type, increasing the risk of overloading. Sling tags must be legible and attached.

  146. Question 146Recognize associated hazards

    What is a critical hazard when performing a lift with a crane that has not been leveled properly?

    1. The crane may tip over due to uneven load distribution. Correct answer.
    2. The crane's tires may wear unevenly.
    3. The crane's engine may run faster.
    4. The crane's boom may become longer.

    Explanation

    An unlevel crane can shift its center of gravity, leading to tipping or structural failure. Cranes must be set up on a level surface according to the manufacturer's specifications.

  147. Question 147Recognize associated hazards

    What is the primary hazard of using a sling that is in contact with a load that is being welded?

    1. The sling may be damaged by heat or sparks. Correct answer.
    2. The sling may become stronger.
    3. The sling may become lighter.
    4. The sling may become magnetic.

    Explanation

    Welding sparks and heat can burn or melt synthetic slings and weaken wire rope or chain. Slings should be protected from welding operations or removed.

  148. Question 148Recognize associated hazards

    What is a key hazard when lifting a load with a crane that is not equipped with a load moment indicator (LMI) or similar device?

    1. The operator may not know the load weight.
    2. The crane may become lighter.
    3. The operator may exceed the crane's capacity without warning. Correct answer.
    4. The crane may become electrically charged.

    Explanation

    Without an LMI, the operator lacks real-time feedback on load moment and capacity, increasing the risk of overloading and tip-over. LMI systems help prevent such incidents.

  149. Question 149Recognize associated hazards

    What is the main hazard of using a sling that is too short for the load, causing a vertical hitch?

    1. The sling may become conductive.
    2. The sling may become lighter.
    3. The sling may become longer.
    4. The sling may be overloaded because the entire load is on one leg. Correct answer.

    Explanation

    A vertical hitch puts the entire load on a single sling leg, which may exceed its capacity if not rated for the full load. Using multiple legs or a longer sling distributes the load.

  150. Question 150Recognize associated hazards

    What is a critical hazard when lifting a load that is aerodynamically shaped and exposed to wind?

    1. The load may act like a sail and cause loss of control. Correct answer.
    2. The load may change color.
    3. The load may become magnetized.
    4. The load may become heavier.

    Explanation

    Aerodynamic loads can catch the wind and cause the load to swing or rotate, leading to loss of control and potential injury. Wind speed limits and tag lines should be used.

  151. Question 151Use various types of rigging equipment and basic hitches and their applications

    What is the primary purpose of a shackle in a rigging assembly?

    1. To connect rigging components and provide a lifting point Correct answer.
    2. To protect slings from sharp edges
    3. To adjust the length of a sling
    4. To measure the tension in a sling

    Explanation

    A shackle is a U-shaped piece of hardware with a pin or bolt, used to connect slings, chains, or other rigging components to a load or to each other. It provides a secure, removable connection point.

  152. Question 152Use various types of rigging equipment and basic hitches and their applications

    Which type of hitch is formed by passing the sling around the load and hooking it back onto itself?

    1. Bridle hitch
    2. Vertical hitch
    3. Basket hitch
    4. Choker hitch Correct answer.

    Explanation

    A choker hitch is made by passing the sling around the load and then through one of the eyes or around the standing part, so the sling tightens around the load when lifted. This hitch grips the load and can reduce the sling capacity.

  153. Question 153Use various types of rigging equipment and basic hitches and their applications

    When using a basket hitch, the lifting capacity of the sling is generally:

    1. Half the capacity of a single vertical leg
    2. Twice the capacity of a single vertical leg Correct answer.
    3. The same as a single vertical leg
    4. Dependent on the sling angle only

    Explanation

    In a basket hitch, the load is supported by two parts of the sling, so the capacity is typically twice that of a single vertical leg, provided the sling legs are vertical and the load is balanced. However, if the sling legs are not vertical, the capacity is reduced by the angle factor.

  154. Question 154Use various types of rigging equipment and basic hitches and their applications

    What is the main advantage of using a synthetic web sling over a wire rope sling?

    1. Lighter weight and less damage to the load surface Correct answer.
    2. Greater capacity at high temperatures
    3. Better resistance to cutting
    4. Higher resistance to abrasion

    Explanation

    Synthetic web slings are lighter and softer than wire rope slings, reducing the risk of damage to the load's surface. They are also easier to handle and less likely to cause injury if they fail.

  155. Question 155Use various types of rigging equipment and basic hitches and their applications

    What is the purpose of a spreader beam in a lifting operation?

    1. To protect the slings from sharp edges
    2. To measure the weight of the load
    3. To increase the lifting capacity of the crane
    4. To keep the sling legs vertical and prevent inward force on the load Correct answer.

    Explanation

    A spreader beam is a rigid member that holds the sling legs apart, keeping them vertical or at a desired angle. This prevents horizontal forces from compressing the load and allows the use of shorter slings.

  156. Question 156Use various types of rigging equipment and basic hitches and their applications

    When rigging a load with a two-leg bridle sling, the included angle between the legs is 60 degrees. What is the approximate tension in each leg if the load weighs 2,000 lbs and is symmetrical?

    1. 1,155 lbs Correct answer.
    2. 1,000 lbs
    3. 2,309 lbs
    4. 2,000 lbs

    Explanation

    For a symmetrical two-leg bridle, the tension in each leg is (Load/2) / cos(θ/2), where θ is the included angle. Here, θ/2 = 30°, cos 30° ≈ 0.866, so tension = (2000/2)/0.866 ≈ 1155 lbs.

  157. Question 157Use various types of rigging equipment and basic hitches and their applications

    What does the term 'choker hitch' imply about the sling's capacity compared to a vertical hitch?

    1. The capacity remains the same
    2. The capacity is increased
    3. The capacity depends only on the load weight
    4. The capacity is decreased Correct answer.

    Explanation

    A choker hitch reduces the sling's capacity because the sling is compressed against the load and itself, creating stress concentrations. The capacity is typically reduced to about 75-80% of the vertical capacity, depending on the sling type.

  158. Question 158Use various types of rigging equipment and basic hitches and their applications

    Which of the following is a proper method for inspecting a wire rope sling before use?

    1. Measuring the length with a tape measure
    2. Testing it by lifting a load beyond its WLL
    3. Checking for broken wires, kinks, and corrosion Correct answer.
    4. Weighing the sling on a scale

    Explanation

    Inspection of wire rope slings includes checking for broken wires, kinks, birdcaging, corrosion, and wear. These defects can significantly reduce the sling's strength.

  159. Question 159Use various types of rigging equipment and basic hitches and their applications

    What is the function of a turnbuckle in a rigging system?

    1. To provide a lifting point on a load
    2. To connect two slings at an angle
    3. To adjust the tension or length of a rigging assembly Correct answer.
    4. To measure the load's weight

    Explanation

    A turnbuckle is a device with threaded ends that allows precise adjustment of tension or length in a rigging assembly. It is commonly used to tighten or loosen cables, rods, or slings.

  160. Question 160Use various types of rigging equipment and basic hitches and their applications

    When using a two-leg sling with an included angle of 90 degrees, what is the approximate load factor applied to each leg's capacity?

    1. 1.414
    2. 0.707 Correct answer.
    3. 0.866
    4. 1.0

    Explanation

    The load factor for a sling leg at an angle is the cosine of the angle from vertical. For a 90-degree included angle, each leg is 45 degrees from vertical, and cos 45° ≈ 0.707. Thus, each leg's capacity is multiplied by 0.707.

  161. Question 161Use various types of rigging equipment and basic hitches and their applications

    What is the primary reason for using a softener or wear pad between a sling and a load?

    1. To adjust the sling's length
    2. To increase the sling's capacity
    3. To provide a lifting point
    4. To protect the sling from sharp edges and abrasion Correct answer.

    Explanation

    Softener or wear pads are placed between the sling and the load to protect the sling from sharp edges, abrasion, and cutting. They help maintain the sling's integrity and safety.

  162. Question 162Use various types of rigging equipment and basic hitches and their applications

    Which of the following is a characteristic of a chain sling compared to a wire rope sling?

    1. Chain slings are not suitable for overhead lifting
    2. Chain slings have lower strength-to-weight ratio
    3. Chain slings can operate at higher temperatures Correct answer.
    4. Chain slings are more susceptible to damage from sharp edges

    Explanation

    Chain slings are known for their ability to withstand high temperatures and abrasive conditions. They are often used in foundries and steel mills where heat is a factor.

  163. Question 163Use various types of rigging equipment and basic hitches and their applications

    What is the correct procedure for determining the weight of a load before lifting?

    1. Estimate by visual inspection alone
    2. Use a load cell or calculate from known material density and dimensions Correct answer.
    3. Lift the load slightly and observe the crane's reaction
    4. Assume the weight is within the crane's capacity

    Explanation

    The weight of a load should be determined accurately, either by using a load cell or by calculating from the material's density and the object's dimensions. Visual estimation is unreliable and can lead to overloading.

  164. Question 164Use various types of rigging equipment and basic hitches and their applications

    What does the term 'rigging triangle' refer to in a lifting operation?

    1. The angle between the sling legs and the horizontal
    2. The relationship between the load, the sling legs, and the hook Correct answer.
    3. The three-point lifting arrangement used for stability
    4. The configuration of a three-leg sling

    Explanation

    The rigging triangle is a concept that describes the forces in a sling system: the load weight acts downward, the sling legs exert tension along their lengths, and the hook provides the upward reaction. Understanding this triangle helps in calculating sling tensions.

  165. Question 165Use various types of rigging equipment and basic hitches and their applications

    When using a shackle, what is the correct orientation of the shackle pin?

    1. The pin should be oriented so that the load does not bear on the pin Correct answer.
    2. The pin should be on the load side
    3. The pin orientation does not matter
    4. The pin should be on the sling side

    Explanation

    The shackle pin should be oriented so that the load is not applied to the pin, because the pin is typically the weakest part of the shackle. The load should bear on the bow of the shackle.

  166. Question 166Use various types of rigging equipment and basic hitches and their applications

    What is the purpose of a swivel in a rigging assembly?

    1. To increase the lifting capacity
    2. To measure the load's weight
    3. To allow rotation of the load without twisting the sling Correct answer.
    4. To connect two slings at a fixed angle

    Explanation

    A swivel allows the load to rotate freely without causing the sling to twist or kink. This is useful when lifting loads that may rotate during handling.

  167. Question 167Use various types of rigging equipment and basic hitches and their applications

    Which of the following is a sign that a synthetic web sling should be removed from service?

    1. The sling has been used for less than a year
    2. The sling is a bright color
    3. The sling has cuts, tears, or snags Correct answer.
    4. The sling has a label with the manufacturer's name

    Explanation

    Synthetic web slings should be removed from service if they show signs of damage such as cuts, tears, snags, or burns. These defects can significantly reduce the sling's strength.

  168. Question 168Use various types of rigging equipment and basic hitches and their applications

    What is the effect of increasing the included angle between sling legs on the tension in each leg?

    1. Tension decreases
    2. Tension becomes zero
    3. Tension remains the same
    4. Tension increases Correct answer.

    Explanation

    As the included angle between sling legs increases, the tension in each leg increases for a given load. This is because the vertical component of the tension must still support the load, requiring greater tension as the angle from vertical increases.

  169. Question 169Use various types of rigging equipment and basic hitches and their applications

    What is a common application for a beam clamp in rigging?

    1. Attaching a hoist or sling to a structural beam Correct answer.
    2. Measuring the load's weight
    3. Lifting a load with a single sling
    4. Protecting slings from sharp edges

    Explanation

    A beam clamp is used to attach a hoist, sling, or other rigging hardware to a structural beam, providing a temporary lifting point. It is commonly used in construction and maintenance.

  170. Question 170Use various types of rigging equipment and basic hitches and their applications

    When using a choker hitch on a load, what is the recommended minimum angle between the choker and the load?

    1. 60 degrees
    2. 120 degrees Correct answer.
    3. 30 degrees
    4. 45 degrees

    Explanation

    For a choker hitch, the angle between the choker and the load should be at least 120 degrees to prevent the sling from slipping or cutting into itself. This ensures the choker grips the load securely.

  171. Question 171Use various types of rigging equipment and basic hitches and their applications

    What is the primary function of a lifting eye bolt?

    1. To provide a permanent lifting point on a load Correct answer.
    2. To connect two slings together
    3. To measure the load's weight
    4. To adjust the tension in a sling

    Explanation

    A lifting eye bolt is a hardware item with a threaded shank and a loop (eye) at one end, used to provide a secure lifting point on a load. It is often installed permanently on equipment or structures.

  172. Question 172Use various types of rigging equipment and basic hitches and their applications

    Which of the following is a correct practice when using a basket hitch with two slings?

    1. Attach the slings to the load with choker hitches
    2. Use only one sling for better control
    3. Ensure the slings are crossed to increase stability
    4. Keep the sling legs vertical to maintain capacity Correct answer.

    Explanation

    In a basket hitch, keeping the sling legs as vertical as possible maximizes the capacity and reduces the horizontal forces on the load. Angled legs reduce capacity and can cause the load to shift.

  173. Question 173Use various types of rigging equipment and basic hitches and their applications

    What is the purpose of a tag line in a lifting operation?

    1. To measure the load's weight
    2. To control the load from rotating or swinging Correct answer.
    3. To increase the lifting capacity
    4. To provide edge protection

    Explanation

    A tag line is a rope attached to the load to control its rotation and swinging during the lift. It allows a rigger to guide the load without being in the fall zone.

  174. Question 174Use various types of rigging equipment and basic hitches and their applications

    When calculating the tension in a sling leg, what information is needed besides the load weight?

    1. The length of the sling
    2. The angle of the sling leg from vertical Correct answer.
    3. The sling's color
    4. The manufacturer's name

    Explanation

    The tension in a sling leg depends on the load weight and the angle of the sling leg from vertical. The tension is calculated as (Load/Number of legs) / cos(angle).

  175. Question 175Use various types of rigging equipment and basic hitches and their applications

    Which hitch is formed by passing the sling around the load and through itself, creating a noose that tightens under load?

    1. Choker hitch Correct answer.
    2. Bridle hitch
    3. Basket hitch
    4. Vertical hitch

    Explanation

    A choker hitch is made by passing the sling around the load and then through one of the eyes or a choking point, so the sling tightens when lifted. This hitch reduces the sling's capacity compared to a vertical hitch.

  176. Question 176Use various types of rigging equipment and basic hitches and their applications

    What is the primary purpose of a spreader beam in a lifting operation?

    1. To protect the sling from sharp edges
    2. To increase the lifting capacity of the crane
    3. To measure the weight of the load
    4. To keep sling legs vertical and prevent inward force on the load Correct answer.

    Explanation

    A spreader beam holds the sling legs apart so they remain vertical, eliminating horizontal compressive forces on the load. This is especially important for long or fragile loads that could buckle under inward pressure.

  177. Question 177Use various types of rigging equipment and basic hitches and their applications

    When using a two-leg bridle sling with an included angle of 60 degrees, what is the approximate load factor applied to each leg?

    1. 0.866
    2. 0.5
    3. 0.577 Correct answer.
    4. 1.0

    Explanation

    The load factor for each leg of a two-leg bridle is calculated as 1 divided by the cosine of half the included angle. For a 60-degree included angle, half is 30 degrees, and cosine 30 degrees is approximately 0.866, so the factor is about 1.155, meaning each leg carries about 57.7% of the load when the load is centered.

  178. Question 178Use various types of rigging equipment and basic hitches and their applications

    When using a two-leg sling with an included angle of 90 degrees, what is the approximate load factor applied to each leg?

    1. 0.707 Correct answer.
    2. 0.866
    3. 1.414
    4. 1.0

    Explanation

    The load factor for each leg is 1 divided by the cosine of half the included angle. For a 90-degree included angle, half is 45 degrees, and cosine 45 degrees is approximately 0.707, so the factor is about 1.414, meaning each leg carries about 70.7% of the load when the load is centered.

  179. Question 179Use various types of rigging equipment and basic hitches and their applications

    What is the effect of using a sling with a longer length on the included angle between legs when the attachment points are fixed?

    1. The included angle becomes 180 degrees
    2. The included angle increases
    3. The included angle decreases Correct answer.
    4. The included angle remains the same

    Explanation

    If the attachment points on the load are fixed and the sling legs are made longer, the legs become more vertical, which decreases the included angle between them. This reduces the tension in each leg for the same load.

  180. Question 180Use various types of rigging equipment and basic hitches and their applications

    Which of the following is a correct method for attaching a sling to a load using a shackle?

    1. Use the shackle as a choker around the load
    2. Place the shackle pin directly on the load edge
    3. Tighten the shackle pin with a cheater bar
    4. Attach the shackle to the load's lifting point and the sling to the shackle bow Correct answer.

    Explanation

    The shackle should be attached to the load's lifting point (e.g., an eye or lug) with the pin through the hole, and the sling should be attached to the bow. This ensures the load is taken on the bow and the pin is not subjected to bending.

  181. Question 181Use various types of rigging equipment and basic hitches and their applications

    What is the purpose of a load cell in a rigging system?

    1. To protect the sling from abrasion
    2. To provide a swiveling connection
    3. To measure the tension or weight in a sling Correct answer.
    4. To increase the lifting capacity

    Explanation

    A load cell is a transducer used to measure the force or weight in a rigging system, providing real-time tension data. It helps ensure that slings and equipment are not overloaded.

  182. Question 182Use various types of rigging equipment and basic hitches and their applications

    When using a two-leg sling with an included angle of 120 degrees, what is the approximate load factor applied to each leg?

    1. 0.5
    2. 1.732
    3. 2.0
    4. 1.0 Correct answer.

    Explanation

    The load factor for each leg is 1 divided by the cosine of half the included angle. For a 120-degree included angle, half is 60 degrees, and cosine 60 degrees is 0.5, so the factor is 2.0, meaning each leg carries 100% of the load when the load is centered.

  183. Question 183Use various types of rigging equipment and basic hitches and their applications

    What does the working load limit (WLL) of a piece of rigging hardware represent?

    1. The load at which the hardware will permanently deform
    2. The load at which the hardware's safety factor reaches zero
    3. The weight of the hardware itself
    4. The maximum load the hardware is rated to lift under normal service conditions Correct answer.

    Explanation

    The working load limit is the maximum mass or force the component is rated to support in general service, and it already accounts for the design safety factor. It is the value riggers use for capacity calculations, not the breaking strength.

  184. Question 184Use various types of rigging equipment and basic hitches and their applications

    What is the standard hand signal for hoisting a load?

    1. Arm extended horizontally with the palm down and the hand waving side to side
    2. Both arms crossed in front of the chest
    3. Forearm raised vertically with the hand held open and still
    4. Arm extended upward with the index finger pointing up and the hand moved in a small circle Correct answer.

    Explanation

    The hoist signal is given by pointing the index finger upward and rotating the hand in a small horizontal circle to indicate the drum should raise the load. Signals must be clear and agreed upon before the lift begins.

  185. Question 185Use various types of rigging equipment and basic hitches and their applications

    Which sling material is generally chosen for a lift where the load has sharp edges and the sling will contact those edges directly?

    1. Wire rope sling with edge protection Correct answer.
    2. Polyester round sling with no protection
    3. Synthetic web sling with no protection
    4. Chain sling with no protection

    Explanation

    Wire rope slings tolerate abrasion and edge contact better than synthetic slings, and edge protection such as softeners should still be used. Synthetic web and round slings can be cut by sharp edges and require protection.

  186. Question 186Use various types of rigging equipment and basic hitches and their applications

    A shackle is being selected for a lift. What does the marked size of a screw-pin shackle refer to?

    1. The clear opening between the shackle legs
    2. The overall length of the shackle
    3. The diameter of the pin
    4. The nominal diameter of the shackle body, not the pin Correct answer.

    Explanation

    Shackle size is stated by the nominal body (bow) diameter, and the rated capacity is based on that body size. The pin diameter is generally smaller than the body diameter.

  187. Question 187Use various types of rigging equipment and basic hitches and their applications

    What is the purpose of a softener placed between a sling and a load?

    1. To convert a choker hitch into a basket hitch
    2. To protect the sling and load from abrasion and sharp edges Correct answer.
    3. To shorten the sling's effective length
    4. To increase the rated capacity of the sling

    Explanation

    Softeners, pads, or edge protectors shield the sling from cutting and abrasion and protect the load surface. They do not change the sling's rated capacity or hitch type.

  188. Question 188Use various types of rigging equipment and basic hitches and their applications

    A single-leg vertical sling has a rated capacity of 4,000 lb. If the same sling is used in a choker hitch, approximately what capacity should be assumed?

    1. 4,000 lb
    2. 8,000 lb
    3. 3,000 lb Correct answer.
    4. 5,600 lb

    Explanation

    A choker hitch reduces a sling's capacity to about 75 percent of its vertical rating because the sling is compressed against the load. For a 4,000 lb vertical rating, the choker capacity is roughly 3,000 lb.

  189. Question 189Use various types of rigging equipment and basic hitches and their applications

    A load is supported by a two-leg bridle sling with an included angle of 60 degrees between the legs. If the load weighs 8,000 lb and is balanced, what is the approximate tension in each leg?

    1. 2,300 lb
    2. 8,000 lb
    3. 4,000 lb
    4. 4,600 lb Correct answer.

    Explanation

    The tension per leg equals half the load divided by the cosine of half the included angle. Half the load is 4,000 lb and the cosine of 30 degrees is about 0.866, giving roughly 4,600 lb per leg.

  190. Question 190Use various types of rigging equipment and basic hitches and their applications

    Why is a basket hitch made with two slings more effective when the slings are kept vertical rather than sloped?

    1. Sloped legs shorten the sling's reach
    2. Vertical legs increase the friction between the sling and the load
    3. Sloped legs reduce the load's center of gravity
    4. Vertical legs carry the load in tension without added horizontal force, so capacity is maximized Correct answer.

    Explanation

    When the legs are vertical, each leg carries only its share of the load with no horizontal component, so the assembly's efficiency is highest. As the legs slope, tension rises and the load may tend to slip or spread.

  191. Question 191Use various types of rigging equipment and basic hitches and their applications

    A rigger needs to lift a load that must stay level and has two lifting points spaced far apart. Which device best distributes the load between the two points?

    1. A single-leg sling
    2. A spreader beam Correct answer.
    3. A choker hitch
    4. A swivel

    Explanation

    A spreader beam holds the sling legs apart at a fixed distance so the load is picked at two points and stays level. It also keeps the sling legs closer to vertical, reducing tension.

  192. Question 192Use various types of rigging equipment and basic hitches and their applications

    What is the correct way to attach a sling to a load using a screw-pin shackle so the assembly is stable under load?

    1. Place the sling in the bow and the load line or eye over the pin, with the pin fully seated Correct answer.
    2. Place the sling on the pin and the load line in the bow, leaving the pin hand-tight
    3. Place the sling over the pin and tighten the pin with a cheater bar
    4. Place the sling in the bow and the load line over the pin, leaving the pin loose

    Explanation

    The sling should bear in the bow of the shackle and the pin should be fully seated and tightened so it cannot unscrew under load. Loading the pin directly can bend it or allow it to rotate loose.

  193. Question 193Use various types of rigging equipment and basic hitches and their applications

    A wire rope sling shows a broken wire in the outer strands. What is the appropriate action?

    1. Continue using it but reduce the load by half
    2. Wrap the broken end with tape and continue
    3. Remove the sling from service and tag it out Correct answer.
    4. Shorten the sling and continue using it

    Explanation

    Broken wires are a removal criterion for wire rope slings because they indicate fatigue and reduce strength. The sling should be taken out of service and tagged so it is not reused.

  194. Question 194Use various types of rigging equipment and basic hitches and their applications

    A chain sling is being inspected and one link shows a noticeable stretch compared with the others. What does this indicate?

    1. The link should be hammered back to shape and reused
    2. The link has been overloaded and the sling should be removed from service Correct answer.
    3. The link is stronger because it has yielded
    4. The link is normal wear and the sling may be used at full capacity

    Explanation

    Stretched or elongated links indicate overloading or heat damage and are a removal criterion for chain slings. The chain should be tagged out and not returned to service.

  195. Question 195Use various types of rigging equipment and basic hitches and their applications

    A rigger is choosing between a single wrap choker and a double wrap choker on a smooth cylindrical load. What is the main advantage of the double wrap?

    1. It doubles the rated capacity of the sling
    2. It allows the load to rotate freely
    3. It eliminates the need for a tag line
    4. It grips the load with more contact and reduces the chance of slipping Correct answer.

    Explanation

    A double wrap increases contact area and friction so the sling grips the load better and is less likely to slip. It does not change the rated capacity of the sling.

  196. Question 196Use various types of rigging equipment and basic hitches and their applications

    A load is being lifted with a two-leg sling where one leg is noticeably longer, so the load hangs off level. What is the main concern?

    1. Both legs carry equal tension regardless of length
    2. The sling's rated capacity increases because the legs differ
    3. The shorter leg carries more tension and the load may shift Correct answer.
    4. The longer leg carries more tension and the load may shift

    Explanation

    When a load hangs off level, the load's center of gravity is not centered between the pick points, so the leg nearer the center of gravity carries more tension. The imbalance can also cause the load to shift or swing.

  197. Question 197Use various types of rigging equipment and basic hitches and their applications

    A load is supported by a four-leg sling assembly with legs at uneven angles. How should the rigger treat the capacity of the assembly?

    1. Assume only two legs share the load unless the load is rigid and the legs are equalized Correct answer.
    2. Assume the assembly capacity is four times a single leg
    3. Assume the assembly capacity is the sum of the two longest legs
    4. Assume all four legs share the load equally

    Explanation

    With four legs at uneven angles, the load is rarely shared equally, so conservative practice is to assume only two legs carry the load unless the load is rigid and the legs are equalized. This prevents overestimating capacity.

  198. Question 198Use various types of rigging equipment and basic hitches and their applications

    A load is being lifted with a two-leg sling and the load's center of gravity is closer to the right pick point. Which statement best describes the tension in the legs?

    1. The right leg carries more tension because it is closer to the center of gravity Correct answer.
    2. Both legs carry equal tension because the load is balanced
    3. The left leg carries more tension because it is farther from the center of gravity
    4. The leg with the longer sling carries more tension

    Explanation

    Tension in each leg is proportional to its share of the load, and the leg nearer the center of gravity carries the larger share. The farther leg carries less.

  199. Question 199Use various types of rigging equipment and basic hitches and their applications

    What is the primary purpose of a tag line in a lifting operation?

    1. To secure the load to the hook
    2. To add lifting capacity to the crane
    3. To measure the load's weight
    4. To control the load's rotation and swing from a safe distance Correct answer.

    Explanation

    A tag line lets a rigger guide and steady the load from outside the fall zone without touching it. It does not add capacity, weigh the load, or attach the load to the hook.

NCCCO Rigger Level I flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Periodic inspection interval
Rigging must receive a documented periodic inspection at least every 12 months, in addition to inspection before each use and at the start of each shift.
Wire rope broken wire rule
Remove a wire rope sling from service when 12 randomly distributed broken wires occur in one lay, or 4 broken wires in one strand in one lay.
Chain sling stretch limit
A chain sling is removed from service when any link has stretched more than 5 percent of its original length or shows cracks, nicks, or gouges.
Web sling rejection signs
Cuts, snags, holes, burns, ultraviolet degradation, broken stitching, or a missing load tag require removal of a synthetic web sling from service.
Hook throat opening rule
A hook is removed from service when its throat opening has increased more than 5 percent or wear exceeds 10 percent of the original dimension.
Shackle inspection criteria
Reject a shackle showing cracks, a bent pin, a distorted bow, or threads that will not fully engage; the pin must be the correct type and fully seated.
Sling ID tag requirement
Every sling must carry a legible tag showing its rated capacity and identification; a missing or unreadable tag means the sling is out of service.
Round sling core damage
A synthetic round sling is removed from service when the cover is damaged enough to expose the core or when core yarns are broken.
Vertical hitch capacity
A vertical hitch carries the full single-leg rated capacity of the sling, with the load hanging directly below the hook.
Choker hitch capacity
A choker hitch reduces sling capacity to roughly 75 to 80 percent of the vertical rating because the sling bends back on itself.
Basket hitch capacity
A basket hitch with both legs vertical can reach up to 200 percent of the single-leg vertical rating, but capacity drops as legs angle outward.
Sling tension formula
Leg tension equals load weight multiplied by the load factor, divided by the number of legs; the load factor rises as the horizontal angle decreases.
Sling angle factor
The tension multiplier is about 1.155 at 60 degrees from horizontal, 1.414 at 45 degrees, and 2.0 at 30 degrees.
D/d ratio effect
Capacity of a wire rope sling in basket or choker hitch decreases as the ratio of bend diameter to rope diameter falls below 25.
Bridle hitch angle limit
In a bridle hitch, the included angle between legs should not exceed 90 degrees; wider angles sharply increase leg tension and reduce capacity.
Bowline strength retention
A bowline knot retains roughly 60 to 70 percent of the rope's strength; knots generally reduce rope strength by 40 to 60 percent.
Knots in wire rope
Knots must never be tied in wire rope or chain slings; knots are only appropriate in fiber rope where reduced capacity is accounted for.
Shock loading hazard
Sudden application of load, such as jerking or dropping, can multiply forces several times over static weight and overload the rigging.
Center of gravity rule
The hook must be positioned directly above the load's center of gravity, or the load will tilt and shift when lifted.
Low sling angle risk
As the horizontal angle falls below 45 degrees, leg tension rises sharply and horizontal force on the load increases, risking sling failure.
Suspended load rule
Never stand or pass any body part under a suspended load; keep hands and feet clear of pinch points, hook throats, and contact points.
Electrical approach hazard
Maintain the required minimum approach distance from energized lines; wet conditions and conductive rigging increase the risk of electrocution.
Environmental load hazards
Wind, ice, rain, and heat affect load stability and rigging capacity; tag lines control rotation and swing during lifting.
Sharp edge protection
Sharp corners cut slings; use softeners, corner protectors, or edge rollers to prevent abrasion and cutting of the sling body.
Primary rigging failure causes
Overloading, worn or damaged gear, improper hitch selection, edge contact, and load shift are the leading causes of rigging accidents.
Chain sling grade rule
Only grade 80 or grade 100 chain is used for overhead lifting; proof coil and transport chain must never be used as slings.
Web sling limitations
Synthetic web slings are lightweight and non-marring but vulnerable to cuts, ultraviolet light, chemicals, and heat, so protect them from sharp edges.
Shackle pin selection
Use a screw pin shackle for temporary or repeated connections and a bolt-type shackle for permanent or long-term connections.
Hook loading rule
Never tip-load a hook; the load must seat in the bowl of the hook, and the hook must have a functioning latch or be moused.
Spreader beam function
A spreader beam converts the lifting force into compression and bending in the beam, keeping sling legs vertical and reducing load on the pick points.
Equalizer beam function
An equalizer beam distributes load between pick points without imposing a bending moment, useful when pick points are not equidistant from the center of gravity.
Tag line purpose
A tag line controls load rotation and swing; keep personnel clear of the load path and never wrap a tag line around a body part.

NCCCO Rigger Level I study guide

Inspecting Rigging Before Use

Why inspection comes first

Every lift begins with an inspection, and exam questions reward the habit of rejecting damaged gear before it is loaded. Know the removal criteria for the major components: slings (wire rope, chain, synthetic web), shackles, hooks, master links, swivels, and hardware.

Common removal criteria to memorize

  • Wire rope slings: broken wires, kinking, bird-caging, crushing, corrosion, heat damage, or a broken strand. Reject hooks with cracks, deformation, or a throat opening increased more than 15 percent.
  • Chain slings: cracks, stretched links, gouges, nicks, bent or twisted links, and excessive wear (commonly 10 percent reduction in link thickness or a stretch indicating overload).
  • Synthetic web slings: burns, holes, tears, snags, embedded grit, ultraviolet degradation, and missing or illegible tags. Red warning yarn showing through the cover is a reject.
  • Shackles and hooks: bent pins, cracked bodies, missing safety latches, and worn threads.

Traps to watch

Questions often test the tag requirement (all slings must carry a legible identification tag), the difference between surface damage and structural damage, and whether a safety latch is mandatory on hooks used for lifting. Another trap: confusing inspection intervals with removal criteria. A periodic inspection schedule does not excuse a pre-use inspection.

Rule of thumb

If you cannot read the tag, you cannot verify the rated capacity, so the item is out of service until re-tagged. When in doubt, remove it from service - the cost of a sling is trivial compared with a dropped load.

Worked example

A chain sling shows a link worn from 13 mm to 11.8 mm. Reduction = 1.2/13 ≈ 9.2 percent, under the 10 percent threshold, but the gouge and twist still justify rejection. Inspect against every criterion, not just one number.

Hitch Configurations, Capacities, and Basic Knots

Hitch types and how capacity changes

A vertical hitch uses one leg straight up and gives full rated capacity. A choker hitch wraps the sling around the load and chokes it; it typically reduces capacity to about 75-80 percent of vertical. A basket hitch cradles the load and can roughly double capacity when both legs are vertical. A bridle hitch uses two or more legs at an angle to a common point.

The sling angle effect

As the angle between the sling leg and horizontal decreases, tension in each leg increases. At 60 degrees, each leg carries about 1.15 times half the load; at 45 degrees, about 1.41 times; at 30 degrees, about 2 times. Never rig below 30 degrees from horizontal without engineering approval. Memorize the load factor concept: tension = (load / number of legs) / sin(angle).

Basic knots and terminations

Know the bowline (creates a fixed loop that will not slip or jam), the clove hitch (quick attachment to a post or rail), and the timber hitch (used to drag or lift logs). Knots reduce rope strength - a bowline can cut capacity by 30-40 percent. For lifting, prefer certified slings and hardware over knots.

Traps

The exam loves to test whether a choker reduces capacity, whether basket doubles capacity only if legs are vertical, and whether a sling angle below 30 degrees is acceptable. Also watch for questions about D/d ratio (bend radius) reducing capacity.

Rule of thumb

For quick field math, remember 60° = 1.15, 45° = 1.41, 30° = 2.0 tension multipliers.

Recognizing Associated Hazards

The hazard mindset

Rigging hazards fall into categories: load hazards (overload, shifting, unstable center of gravity), environmental hazards (wind, power lines, poor visibility, ground conditions), personnel hazards (struck-by, pinch points, caught-between), and equipment hazards (shock loading, side loading, worn gear).

Key hazards to name

  • Shock loading: sudden jerks multiply force far beyond static weight. Always take up slack slowly.
  • Side loading: pulling a sling or hook sideways beyond its design reduces capacity dramatically.
  • Power lines: maintain the required minimum clearance; treat all lines as energized.
  • Ground conditions: soft soil, slopes, and voids can cause outrigger settlement and tip-over.
  • Pinch and crush points: hands and feet near shackles, hooks, and load edges.
  • Wind: affects load swing and can exceed crane or rigging limits.

Traps in questions

Watch for distractor answers that blame the operator when the real hazard is equipment or environment. Also note the difference between hazard (a condition) and risk (the chance of harm). Questions may ask which control is most effective - engineering controls (barricades, exclusion zones) beat administrative controls (signage) and PPE.

Rule of thumb

Use the hierarchy of controls: eliminate, substitute, engineer, administrate, then PPE. Barricading a swing radius is stronger than posting a warning sign.

Worked example

A load swings toward a worker because wind gusts. The best control is to establish an exclusion zone and use tag lines from outside the swing path - not to tell the worker to duck.

Rigging Equipment and Hitch Applications

Matching equipment to the job

Rigging equipment includes wire rope slings, chain slings, synthetic web and round slings, shackles, hooks, master links, swivels, turnbuckles, spreader beams, and tag lines. Each has strengths: chain resists abrasion and heat; wire rope handles heavy loads; synthetic slings are light and non-marring but vulnerable to cuts and heat.

Hitch applications

  • Vertical: single leg, full capacity, simplest and strongest.
  • Choker: grips the load itself, good for pipe and bundles, but reduces capacity.
  • Basket: cradles the load, doubles capacity when legs are vertical, protects the load surface.
  • Bridle: multiple legs to a common point, used when lifting points are spread apart.

Hardware and safe practice

Shackles connect slings to loads; use the screw pin fully seated and never replace a pin with a bolt. Hooks need safety latches. Spreader beams keep sling legs vertical and prevent crushing the load. Tag lines control rotation and swing from a safe distance.

Traps

Questions test whether you know basket capacity depends on leg angle, whether synthetic slings can be used around sharp edges (only with protection), and whether chain is preferred for abrasive or hot loads. Also watch for confusion between working load limit (WLL) and breaking strength - never rig to breaking strength.

Rule of thumb

Rig so the load is balanced and the center of gravity is below the hook. Keep sling legs as vertical as practical to maximize capacity.

NCCCO Rigger Level I cheat sheet

Quick reference

Inspecting Rigging Before Use

  • Inspection frequency rule: rigging is inspected before each use and at the start of each shift, plus a documented periodic inspection at intervals not exceeding 12 months.

  • Sling removal criteria: remove from service for broken wires, severe corrosion, kinks, birdcaging, crushed or deformed fittings, or missing/t illegible ID tags.

  • Wire rope rejection benchmarks: 12 randomly distributed broken wires in one lay, 4 broken wires in one strand in one lay, or any valley corrosion.

  • Chain sling rejection: any crack, nick, gouge, bent or twisted link, stretch exceeding 5% of original length, or wear exceeding 10% of link thickness.

  • Web sling rejection: cuts, snags, holes, burns/charring, ultraviolet degradation, broken stitching, or missing load tag; shock-load or acid damage requires removal.

  • Synthetic round sling rejection: cover damage exposing core, core yarn breakage, or any label that is missing or unreadable.

  • Hardware inspection: hooks with throat opening increased more than 5% (or 15% for some standards) or wear exceeding 10% of original dimension are removed from service.

  • Shackle and eye inspection: reject for cracks, bent pins, distorted bows, or threads that will not fully engage; pins must be the correct type and fully seated.

Quick reference

Hitch Configurations, Capacities, and Basic Knots

  • Vertical hitch capacity equals the sling's single-leg rated capacity; choker hitch reduces capacity to about 75-80% of vertical; basket hitch can reach up to 200% of vertical when legs are vertical.

  • Sling tension formula: T = (Load x Load Factor) / number of legs, where load factor increases as the horizontal angle decreases.

  • Sling angle factor: at 60 degrees from horizontal, tension multiplier is about 1.155; at 45 degrees about 1.414; at 30 degrees about 2.0.

  • D/d ratio rule: capacity of a wire rope sling in a basket or choker hitch decreases as the ratio of bend diameter to rope diameter decreases; ratios below 25 reduce capacity.

  • Choker hitch angle effect: a choker with a large angle between the choked leg and the standing part loses capacity; the tighter the choke around the load, the closer to full choker rating.

  • Bridle hitch: with two or more legs, the included angle between legs should not exceed 90 degrees; capacity drops as the angle widens.

  • Knot rule: knots reduce rope strength by roughly 40-60%; a bowline retains about 60-70% of rope strength, a square knot much less.

  • Never tie knots in wire rope or chain slings; knots are only appropriate in fiber rope where the application permits and the reduced capacity is accounted for.

Quick reference

Recognizing Associated Hazards

  • Shock loading: sudden application of load can multiply forces several times over static weight; avoid jerking, dropping, or swinging loads.

  • Center of gravity: an unbalanced load will tilt; the hook must be directly above the center of gravity or the load will shift when lifted.

  • Sling angle hazard: as the horizontal angle decreases below 45 degrees, leg tension rises sharply and horizontal force on the load increases.

  • Pinch and crush points: hands and feet must stay clear of slings, hook throats, and load contact points; never place body parts under a suspended load.

  • Electrical hazard: maintain the required minimum approach distance from energized lines; wet conditions and conductive rigging increase risk.

  • Environmental hazards: wind, ice, rain, and heat affect load stability and rigging capacity; tag lines control rotation and swing.

  • Rigging failure modes: overloading, worn or damaged gear, improper hitch, edge contact, and load shift are the primary causes of rigging accidents.

  • Load edge protection: sharp corners cut slings; use softeners, corner protectors, or edge rollers to prevent abrasion and cutting.

Quick reference

Rigging Equipment and Hitch Applications

  • Wire rope slings: suited to abrasive and hot environments; inspect for broken wires, kinks, and corrosion; use with thimbles and proper fittings.

  • Chain slings: strong and durable for abrasive and high-temperature service; grade 80 or 100 chain only; never use proof coil or transport chain for overhead lifting.

  • Synthetic web and round slings: lightweight and non-marring but vulnerable to cuts, UV, chemicals, and heat; protect from sharp edges.

  • Shackles: screw pin for temporary or repeated connections; bolt-type for permanent or long-term connections; never side-load a shackle beyond its rated capacity.

  • Hooks: use hooks with a functioning latch or moused hook; never tip-load a hook; load must seat in the bowl of the hook.

  • Spreader and equalizer beams: spreader beams convert compressive load into beam bending; equalizer beams distribute load between pick points without a bending moment.

  • Tag lines: control load rotation and swing; keep personnel clear of the load path and never wrap a tag line around a body part.

  • Rigging hardware identification: verify rated capacity markings on slings and hardware; unmarked or unrated gear must not be used for overhead lifting.

NCCCO Rigger Level I key terms

Working Load Limit (WLL)

The maximum load that a sling, shackle, or other rigging component is rated to lift safely under normal service conditions, as set by the manufacturer and marked on the item.

Related: Rated Capacity, Design Factor, Sling Angle
Rated Capacity

The maximum load a piece of lifting equipment is designed to handle for a given configuration, often stated in the manufacturer's charts and adjusted for hitch type and angle.

Related: Working Load Limit (WLL), Sling Angle, Hitch Configuration
Design Factor

The ratio of a component's breaking strength to its working load limit, providing a safety margin against overload, wear, and dynamic forces during lifting.

Related: Working Load Limit (WLL), Breaking Strength
Breaking Strength

The load at which a sling or fitting will fail or rupture, determined by testing or manufacturer data and always higher than the working load limit.

Related: Design Factor, Working Load Limit (WLL)
Sling Angle

The angle measured between a sling leg and the horizontal load surface, which determines how much of the sling's capacity is available to carry the load.

Related: Tension Increase, Sling Leg, Working Load Limit (WLL)
Tension Increase

The added force in each sling leg as the angle between the legs and the load becomes steeper or narrower, requiring reduced load per leg to avoid overloading.

Related: Sling Angle, Sling Leg
Sling Leg

One individual branch or segment of a multi-leg sling assembly that runs from the master link or hook down to the attachment point on the load.

Related: Sling Angle, Bridle Sling, Master Link
Vertical Hitch

A hitch in which a single sling leg runs straight up from the load to the hook, allowing the sling to be used at its full rated vertical capacity.

Related: Choker Hitch, Basket Hitch, Sling Angle
Choker Hitch

A hitch formed by passing the sling around the load and through one eye or fitting so the sling tightens on itself, reducing capacity compared with a vertical hitch.

Related: Vertical Hitch, Basket Hitch, Choker Angle
Basket Hitch

A hitch in which the sling passes under or around the load and both ends attach to the hook, cradling the load without the sling choking on itself.

Related: Vertical Hitch, Choker Hitch, Double Wrap
Choker Angle

The angle at which a choker hitch grips the load; when the choke is pulled tight against the load at roughly 120 degrees, the sling retains its full choker rating.

Related: Choker Hitch, Sling Angle
Double Wrap Choker

A choker hitch in which the sling is wrapped around the load twice before passing through the eye, increasing grip and reducing the chance of slipping.

Related: Choker Hitch, Basket Hitch
Bridle Sling

A sling assembly with two or more legs joined at a master link or ring, used to attach to multiple lifting points on a load and share the weight among them.

Related: Sling Leg, Master Link, Sling Angle
Master Link

The large ring or link at the top of a multi-leg sling assembly that gathers the legs together and connects to the crane hook.

Related: Bridle Sling, Shackle
Shackle

A U-shaped metal fitting with a pin or bolt across the opening, used to connect slings, hooks, and loads; must be rated and matched to the load.

Related: Master Link, Rigging Hook
Rigging Hook

A hook with a safety latch or other retaining device used to connect slings and hardware to the crane or load, designed so the load cannot slip off.

Related: Shackle, Safety Latch
Safety Latch

A spring-loaded gate on a hook that closes the throat opening to keep slings and attachments from slipping off during lifting.

Related: Rigging Hook, Hook Throat
Hook Throat

The inside curve or opening of a hook where the load-bearing sling or fitting sits; its width and condition affect the hook's safe working capacity.

Related: Safety Latch, Rigging Hook
Synthetic Web Sling

A flat or round sling made of woven nylon or polyester fibers, lightweight and soft on loads but vulnerable to cuts, abrasion, and ultraviolet degradation.

Related: Wire Rope Sling, Chain Sling, Sling Inspection
Wire Rope Sling

A sling made from strands of steel wire twisted into rope, strong and resistant to heat and abrasion but requiring inspection for broken wires and kinks.

Related: Synthetic Web Sling, Chain Sling, Broken Wire
Chain Sling

A sling made of alloy steel chain links, durable and tolerant of abrasion and heat, but subject to wear, stretching, and cracking at the links.

Related: Wire Rope Sling, Synthetic Web Sling, Sling Inspection
Sling Inspection

The process of examining a sling before each use for damage such as cuts, broken wires, worn links, missing tags, or other defects that make it unsafe to use.

Related: Sling Tag, Broken Wire, Removal from Service
Sling Tag

The durable label attached to a sling showing its manufacturer, working load limit, and other ratings; if missing or unreadable, the sling should not be used.

Related: Sling Inspection, Working Load Limit (WLL)
Removal from Service

The act of taking a damaged or questionable piece of rigging out of use and tagging or destroying it so it cannot be accidentally used for lifting.

Related: Sling Inspection, Sling Tag
Broken Wire

A single failed wire in a wire rope sling; a concentration of broken wires in one strand or area is a defect requiring the sling to be removed from service.

Related: Wire Rope Sling, Sling Inspection
Kinking

A sharp bend or twist set permanently into wire rope or chain that weakens the material and is a reason to remove that sling from service.

Related: Wire Rope Sling, Removal from Service
Center of Gravity

The point in a load where its weight is balanced in all directions; the hook must be positioned above this point for the load to hang level and stable.

Related: Load Balance, Sling Angle
Load Balance

The condition in which a lifted load hangs level and stable because the lifting points and sling lengths distribute the weight evenly around the center of gravity.

Related: Center of Gravity, Bridle Sling
Load Control

The use of tag lines or other means to keep a suspended load from swinging or rotating during lifting, so workers stay clear and the load lands accurately.

Related: Tag Line, Shock Loading
Tag Line

A rope attached to a load and handled by a worker from a safe distance to guide and steady the load without touching it directly.

Related: Load Control
Shock Loading

A sudden, jerking application of force to rigging, such as a rapid hoist start, that can exceed the working load limit and cause failure even on a properly rated sling.

Related: Load Control, Working Load Limit (WLL)
Rigging Angle

The angle at which a sling leg meets the load or the hook; steeper angles reduce the load per leg while flatter angles increase tension in each leg.

Related: Sling Angle, Tension Increase
Bowline Knot

A fixed loop knot that will not slip under load and is easy to untie, sometimes used for non-critical tie-offs but not a substitute for rated rigging hardware.

Related: Clove Hitch Knot, Tag Line
Clove Hitch Knot

A simple knot used to tie a rope to a post or rail, handy for temporary tag lines but known to slip if the load direction changes.

Related: Bowline Knot, Tag Line
Two-Leg Sling Capacity

The rated load a two-leg sling can carry, which depends on the angle between the legs and is less than twice the single-leg capacity at any angle below vertical.

Related: Sling Angle, Bridle Sling, Tension Increase
Softener

A pad or sleeve placed between a sling and a sharp or abrasive load edge to protect the sling from cuts and wear.

Related: Synthetic Web Sling, Sling Inspection
Edge Protection

Any material or device, such as corner guards or wear pads, used to keep slings and rigging from being cut or damaged by load edges.

Related: Softener, Sling Inspection

NCCCO Rigger Level I study plan

8 weeks · About 6 hours per week

Week 1

Inspect rigging before use & Recognize associated hazards

  • List every rigging component in a sling inventory (sling legs, shackles, hooks, master links, swivels, turnbuckles, wire rope clips) and state the specific defect each is inspected for

  • Describe the removal-from-service criteria for synthetic web slings, wire rope slings, and chain slings from memory without notes

  • Perform a documented pre-use inspection sequence on five different sling types and record pass/fail with the reason for each fail

  • Identify the tag and identification markings a sling must carry and explain why a missing tag means removal from service

Your checkpoint

A one-page inspection checklist covering five sling types with at least eight removal-from-service criteria per type, validated against a hands-on inspection of five slings

Week 2

Inspect rigging before use & Recognize associated hazards

  • Inspect shackles, hooks, master links, and eye bolts and state the wear, deformation, and crack limits that trigger rejection

  • Explain hook latch, throat opening, and twist criteria and demonstrate measuring them

  • Match each hardware defect to the hazard it creates if the item is left in service

  • Sequence a job-site rigging inspection from arrival through pre-lift, noting what changes at each stage

Your checkpoint

A written inspection log for ten pieces of hardware with measured values, accept/reject decisions, and the hazard cited for each rejection

Week 3

Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots & Use various types of rigging equipment and basic hitches and their applications

  • Name and demonstrate the vertical, choker, basket, and bridle hitches and state how each changes the load on the sling

  • Calculate sling tension for a two-leg bridle at a given included angle using the load-angle relationship

  • Explain the effect of horizontal sling angle on leg tension and compute tension at 60, 45, and 30 degrees

  • Identify the loss of capacity caused by choker and basket configurations and state the applicable efficiency factor

Your checkpoint

A tension-calculation worksheet with at least eight solved bridle and basket problems showing load, angle, and resulting leg tension

Week 4

Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots & Use various types of rigging equipment and basic hitches and their applications

  • Tie and dress a bowline, clove hitch, and two half hitches and explain where each is and is not acceptable in rigging

  • Select the correct hitch for four described load shapes and justify each choice

  • Explain center-of-gravity location and demonstrate how an off-center pick changes sling loading

  • Describe how to control load rotation and tag lines during a lift

Your checkpoint

A hitch-selection table matching at least six load scenarios to a hitch, with the capacity effect and rationale for each

Week 5

Recognize associated hazards

  • Identify the hazards created by sling angles, edge contact, and load shifting and state the control for each

  • Explain the electrical, pinch-point, and struck-by hazards around a lift and where exclusion zones belong

  • Describe environmental and ground-condition hazards that affect rigging and crane stability

  • List the rigging-related causes of dropped loads and rank them by frequency of occurrence in general practice

Your checkpoint

A hazard-and-control register with at least fifteen entries, each pairing a specific hazard with a specific control measure

Week 6

Recognize associated hazards & Inspect rigging before use

  • Walk through a described lift scenario and identify every hazard before rigging begins

  • Explain how load weight, rigging weight, and capacity derating combine to determine whether a lift is safe

  • Describe the roles and communication signals among rigger, signal person, and operator

  • Identify the conditions that require stopping a lift and state how to communicate a stop

Your checkpoint

A written pre-lift hazard analysis for two described scenarios, each with at least eight identified hazards and controls

Week 7

Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots & Use various types of rigging equipment and basic hitches and their applications

  • Assemble a complete rigging system for a described load, including sling type, hitch, hardware, and capacity verification

  • Verify that every component in the system meets or exceeds the required load

  • Explain how to level a load and how to protect slings from edges and corners

  • Describe the inspection points that must be re-checked after rigging is attached and tensioned

Your checkpoint

A complete rigging plan for one described load, including component list, hitch selection, capacity calculations, and edge protection

Week 8

Inspect rigging before use & Identify, select, and attach rigging with basic knowledge of hitch configurations, capacities, and basic knots & Recognize associated hazards & Use various types of rigging equipment and basic hitches and their applications

  • Review all four domains using the weakest areas identified in prior deliverables

  • Complete a full timed practice set and score each domain separately

  • Re-derive the sling-tension and capacity formulas without reference

  • State the removal-from-service criteria for all sling and hardware types in a single pass

Your checkpoint

A timed practice set scored by domain with a written list of remaining weak areas and a remediation plan for each

Milestones

Week 2: Can inspect and accept or reject slings and hardware using documented criteria without reference notes

Week 4: Can calculate bridle and basket sling tension at three angles and select an appropriate hitch for a described load

Week 6: Can complete a pre-lift hazard analysis identifying at least eight hazards with controls for an unseen scenario

Week 8: Scores at or above 80 percent on a timed practice set in each of the four domains

NCCCO Rigger Level I exam day

Your checklist

Government-issued photo ID

Bring a current, unexpired photo ID; the exact accepted forms and name-match requirements should be confirmed with your test provider.

Admission or scheduling confirmation

Print or save the confirmation showing your test date, time, location, and candidate ID number.

Personal protective equipment

Bring a hard hat, safety glasses, work gloves, and sturdy work boots; the practical test is a hands-on evaluation in a work-like setting. Confirm any site-specific PPE requirements with the provider.

Appropriate work clothing

Wear clothing suitable for climbing, handling rigging, and working around equipment; avoid loose items that could snag. Confirm dress expectations with the provider.

Calculator and pencils (if permitted)

Bring a basic calculator and pencils for any load calculations; confirm what materials the provider allows and supplies.

Review load-calculation fundamentals

Practice sling tension, center-of-gravity, and load-weight estimation using the method your training program taught; the practical test may include calculation-based tasks.

Review hand signals and rigging terminology

Be able to give and respond to standard crane hand signals and use correct rigging terminology during the practical tasks.

Practice inspection sequence aloud

Rehearse the order of a pre-use inspection of slings, shackles, and hardware so you can verbalize it clearly to the examiner.

Plan travel and arrival time

Arrive early enough to complete check-in and any site orientation; confirm the required arrival time and site access rules with the provider.

Arrange transportation and site access

Confirm parking, gate access, and any visitor sign-in requirements with the provider before test day.

Bring water and a snack

Practical testing can be physically demanding; bring water and a light snack if the site permits it.

Leave prohibited items behind

Confirm the provider's rules on phones, smart watches, and recording devices; these are commonly restricted during testing.

Plan the day

Final 72 hours

Re-read your training materials on sling types, hitches, hardware inspection, and load calculations. Practice the inspection and rigging sequences out loud as you would perform them for an examiner.

Final 72 hours

Confirm your test date, time, location, and what the provider expects you to bring; ask about PPE, tools, and any site-specific rules.

Final 72 hours

Get adequate rest and avoid last-minute cramming of new material; consolidate what you already know.

Final 24 hours

Pack your ID, confirmation, PPE, and clothing. Lay everything out so nothing is forgotten.

Final 24 hours

Review hand signals and the pre-use inspection checklist one final time; stop studying early enough to sleep well.

Morning of the test

Eat a normal meal, arrive early, and allow time for check-in and site orientation.

Morning of the test

Dress in work clothing and PPE; leave prohibited items in your vehicle or at home per provider rules.

During the test

Listen carefully to each instruction, verbalize your inspection and rigging steps clearly, and ask the examiner to repeat an instruction if you did not hear it.

During the test

Work deliberately and safely; demonstrate proper body positioning and communication rather than rushing through tasks.

Rules to check

  • Follow all site safety rules, including PPE requirements, at all times; the practical test is conducted in a work-like environment.

  • Present valid photo ID at check-in; confirm the accepted forms and name-match requirements with the provider.

  • Confirm the provider's policy on phones, smart watches, and recording devices before test day and comply with it.

  • Ask the examiner to repeat or clarify an instruction if needed; do not guess at a task you did not understand.

  • Confirm the provider's policy on breaks, water, and restroom access during the practical test.

  • Confirm how the practical test is scored, including pass/fail criteria and any retake policy, with the provider before test day.

  • Do not coach or communicate with other candidates during testing; follow the examiner's directions on where to stand and when to begin.

  • Report any injury, equipment defect, or unsafe condition to the examiner immediately.

NCCCO Rigger Level I FAQ

How many NCCCO Rigger Level I practice questions are available?

The practice set has 199 NCCCO Rigger Level I questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many NCCCO Rigger Level I flashcards are available?

The flashcard set has 32 NCCCO Rigger Level I cards. Each card shows the term and its definition.

Which topics does the NCCCO Rigger Level I study material cover?

The NCCCO Rigger Level I study material has 4 sections, including Inspecting Rigging Before Use, Hitch Configurations, Capacities, and Basic Knots, and Recognizing Associated Hazards.

What format facts does the catalog list for the NCCCO Rigger Level I exam?

The catalog lists a duration of 60 minutes and these item types: multiple choice, written examination, and practical examination for the NCCCO Rigger Level I exam.