EPA 608 Practice Test

EPA Section 608 Technician Certification

EPA 608 overview

  • 199 practice questions
  • 32 flashcards
  • 4 study guide topics
  • 36 key terms

What you'll study

  • Type I - Small Appliances25%
  • Type II - High-Pressure Appliances25%
  • Type III - Low-Pressure Appliances25%
  • Universal (Types I, II, and III)25%

Section 608 Technician Certification is the U.S. Environmental Protection Agency credential required under EPA regulations at 40 CFR Part 82, Subpart F, issued under Section 608 of the Clean Air Act. Technicians who maintain, service, repair, or dispose of equipment that could release ozone-depleting refrigerants into the atmosphere must be certified, and since January 1, 2018 that same requirement extends to appliances containing most substitute refrigerants, including HFCs. A candidate earns the credential by passing an EPA-approved test administered by an EPA-approved certifying organization; EPA writes the rule but does not itself give the exams. The tests are specific to the type of equipment the technician intends to work on, which is why the credential comes in equipment-specific categories such as Type I (small appliances), Type II (high-pressure appliances), Type III (low-pressure appliances), and Universal, which covers all three. Section 608 credentials do not expire, so the exam is a one-time hurdle rather than a renewal cycle. Test content follows the Section 608 regulations themselves: the prohibition on venting, refrigerant recovery, recycling and reclamation requirements, recovery and recycling equipment certification, leak repair, safe disposal, refrigerant sales restrictions, and recordkeeping and reporting. Because the questions are regulation-driven, preparation means reading the rule text and EPA's stationary refrigeration pages carefully, then drilling the specific prohibitions, thresholds, and paperwork duties until they are recall-level knowledge. This guide is independent study material and is not affiliated with or endorsed by EPA.

Common mistakes

On a small-appliance job, the candidate selects 'system-dependent' (self-purging) recovery and pulls the charge with the appliance's own compressor, even though the compressor is seized, burned out, or the unit is being scrapped non-running.

They memorize 'small appliances may be recovered with system-dependent equipment' as an unconditional rule and never check the precondition that the appliance compressor must actually operate.

What to do instead

Verify the compressor runs before choosing the method. If it does not, switch to a self-contained recovery machine and recover to the required percentage/vacuum level. System-dependent equipment depends entirely on a working appliance compressor.

Recites '80% or 90%' for small-appliance recovery without attaching the November 15, 1993 date, then picks the wrong number when the question supplies the date.

Two percentages that differ by only ten points get stored as a jingle; the date is the only thing that distinguishes them, so it drops out of memory first.

What to do instead

Store them as a dated pair: recovery equipment from before 11/15/1993 to 80%, equipment from after 11/15/1993 to 90%, with evacuation to 4 in. Hg vacuum as the alternative. Say the date out loud with the number every time you review.

Classifies a rooftop split system, a field-assembled walk-in, or a 3-ton residential condensing unit as Type I work because the equipment 'looks small.'

The word 'small' invites a size judgment, and candidates forget the regulatory definition is about charge amount and construction, not physical dimensions.

What to do instead

Apply the definition: a small appliance is factory-charged, hermetically sealed, and holds 5 lb or less of refrigerant. Anything field-assembled, or holding more than 5 lb, is a Type II high-pressure appliance no matter how compact it is.

On Type II work, names 500 microns, 0 psig, or 'a full vacuum' as the target when recovering refrigerant from a high-pressure appliance.

Deep-vacuum dehydration numbers from installation practice bleed into the recovery question, which uses a different and much less stringent target.

What to do instead

Separate the two ideas. The 608 recovery target for high-pressure appliances is 90% of the charge (80% for older recovery equipment) or evacuation to 4 in. Hg vacuum. 500 microns belongs to evacuating a system for moisture removal before charging, not to recovering refrigerant.

Charges R-410A or R-407C into a system as a vapor, or answers 'vapor' when asked how a blended refrigerant should be charged.

Habit carried over from single-component R-22 charging, where vapor charging is acceptable; the candidate does not connect the word 'blend' to fractionation.

What to do instead

Blends are zeotropic and must be charged as a liquid so components enter in the designed ratio. If liquid cannot safely enter the suction line, throttle liquid in through a metering device. Never vapor-charge a blend.

States that R-410A, R-134a, or other HFC/HFO refrigerants may be vented because they are not ozone-depleting.

The ozone-depletion story dominates study time, so the venting prohibition gets mentally filed under 'CFCs only' and never gets extended to substitutes.

What to do instead

The Section 608 venting ban covers ozone-depleting refrigerants and their substitutes, including HFCs and HFOs. Venting is permitted only under the narrow listed exceptions, such as de minimis releases during good-faith repair attempts.

Answers that a leak on an R-123 chiller lets refrigerant escape into the room and that the main consequence is losing refrigerant charge.

Intuition imported from high-pressure systems, where internal pressure sits above atmosphere; candidates do not register that low-pressure machines run in a vacuum.

What to do instead

Low-pressure chillers normally operate below atmospheric pressure, so a leak draws air and moisture in rather than refrigerant out. The real damage is moisture-driven acid formation and lost capacity from non-condensables, which is why purge units and leak checks get so much attention.

Applies the high-pressure 4 in. Hg vacuum target when asked how far a low-pressure appliance must be evacuated before being opened.

One vacuum number is learned early in the course and then reused for every appliance class, because the candidate never noticed the recovery table has separate rows.

What to do instead

Learn the low-pressure row as its own entry: Type III appliances have a far deeper evacuation requirement than the 4 in. Hg used for high-pressure equipment. Whenever a question names R-11, R-113, or R-123, expect the low-pressure vacuum level, not the high-pressure one.

Uses 'recover,' 'recycle,' and 'reclaim' interchangeably - for example, saying a technician reclaims refrigerant on-site with a recycling machine, or that recycled refrigerant may be sold or put into another customer's equipment.

The three verbs sound like synonyms and always appear together in the same study paragraph, so they collapse into one fuzzy concept.

What to do instead

Anchor one sentence each: recover = remove and store; recycle = clean on-site for reuse in the same system or the same owner's equipment; reclaim = reprocess off-site to ARI-700 new-product purity, the only route that makes refrigerant usable in another owner's equipment.

Mixes up the leak-repair thresholds or the repair window - for example, applies the 20% commercial-refrigeration trigger to a comfort-cooling unit, or allows 60 days to fix a leaking appliance.

Three percentages and one deadline are taught together where only the appliance category changes, so the numbers drift out of their slots under exam pressure.

What to do instead

Recite category-percentage pairs, never a bare list: comfort cooling 10%, commercial refrigeration 20%, industrial process 30%, with repair required within 30 days of discovering a leak above the trigger. These obligations apply to appliances holding 50 lb or more of refrigerant.

Exam requirements can change. Confirm current details with the exam provider.

EPA 608 practice

199 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Type I - Small Appliances

    Technicians who service small appliances must hold which EPA Section 608 certification?

    1. Type II
    2. Universal
    3. Type I Correct answer.
    4. Type III

    Explanation

    Type I certification covers the service, maintenance, and disposal of small appliances, which are factory-charged, hermetically sealed units containing 5 pounds or less of refrigerant. The other certifications apply to different equipment categories.

  2. Question 2Type I - Small Appliances

    When recovering refrigerant from a small appliance, the recovery equipment must remove at least what portion of the charge?

    1. 90 percent of the total charge
    2. 85 percent of the total charge
    3. 95 percent of the total charge
    4. 80 percent of the total charge Correct answer.

    Explanation

    EPA rules require that recovery equipment used on small appliances recover at least 80 percent of the refrigerant charge, regardless of when the equipment was manufactured. Higher recovery percentages apply to certain other appliance categories.

  3. Question 3Type I - Small Appliances

    An appliance qualifies as a small appliance under Section 608 when it contains 5 pounds or less of refrigerant and is

    1. equipped with a liquid receiver
    2. installed inside a residence
    3. field-assembled on site with service valves
    4. hermetically sealed and factory-charged Correct answer.

    Explanation

    The regulatory definition requires the unit to be fully manufactured, charged, and hermetically sealed in a factory with 5 pounds or less of refrigerant. How or where the unit is installed does not determine the category.

  4. Question 4Type I - Small Appliances

    Which action is prohibited when servicing a small appliance?

    1. Venting refrigerant vapor to the atmosphere Correct answer.
    2. Recovering refrigerant into a DOT-approved recovery cylinder
    3. Charging recovered refrigerant back into the same appliance
    4. Recycling refrigerant through filter-driers before reuse

    Explanation

    Section 608 prohibits knowingly venting ozone-depleting refrigerants and their substitutes to the atmosphere during service, maintenance, or disposal. Recovered refrigerant must be recovered, recycled, or reclaimed instead.

  5. Question 5Type I - Small Appliances

    A recovery cylinder should be filled with liquid refrigerant to no more than what level?

    1. 100 percent of its weight capacity
    2. 95 percent of its volume capacity
    3. 90 percent of its weight capacity
    4. 80 percent of its weight capacity Correct answer.

    Explanation

    Cylinders must be filled by weight and never exceed 80 percent of capacity so that a vapor space remains for liquid expansion. Overfilling can cause hydrostatic pressure to rupture the cylinder.

  6. Question 6Type I - Small Appliances

    Under EPA regulations, who may purchase refrigerant?

    1. Any appliance owner
    2. Only licensed contractors
    3. Any member of the public
    4. Only certified technicians Correct answer.

    Explanation

    Refrigerant may be sold only to technicians certified under Section 608. Possession of a business license or ownership of an appliance does not authorize purchase.

  7. Question 7Type I - Small Appliances

    Which of the following is classified as a small appliance under Section 608?

    1. A rooftop unit with a 15-pound charge
    2. A centrifugal chiller
    3. A window air conditioner Correct answer.
    4. A supermarket refrigeration rack

    Explanation

    Window air conditioners are factory-charged, hermetically sealed units with 5 pounds or less of refrigerant, so they are small appliances. Racks, rooftop units with larger charges, and chillers fall under other certifications.

  8. Question 8Type I - Small Appliances

    Which personal protective equipment is most important when handling liquid refrigerant?

    1. A dust mask and cotton work gloves
    2. Safety glasses and insulated work gloves
    3. A respirator and hearing protection
    4. Safety glasses and impervious gloves Correct answer.

    Explanation

    Liquid refrigerant boils at extremely low temperature and can cause frostbite and permanent eye damage on contact. Impervious gloves and eye protection are the essential protection; ordinary cloth or insulated gloves absorb liquid and make injury worse.

  9. Question 9Type I - Small Appliances

    A technician is asked to repair a packaged unit that contains 12 pounds of R-410A. Which certification does this work require?

    1. Type III
    2. Type I
    3. No certification is required
    4. Type II Correct answer.

    Explanation

    Appliances containing more than 5 pounds of a high-pressure refrigerant fall outside the small appliance category and require Type II certification. Type I is limited to appliances with 5 pounds or less.

  10. Question 10Type I - Small Appliances

    What is the difference between recycling and reclaiming refrigerant?

    1. Recycling applies only to HFCs; reclaiming applies only to CFCs
    2. Recycling cleans refrigerant on site; reclaiming restores ARI 700 purity Correct answer.
    3. Recycling is performed only by manufacturers; reclaiming is performed by technicians
    4. Recycling restores refrigerant to ARI 700 purity, while reclaiming only removes oil and moisture

    Explanation

    Recycling reduces contaminants such as oil, moisture, and acid, usually on site with filter-driers, and the result may not meet ARI 700. Reclaiming is reprocessing at a certified facility to meet ARI 700 purity specifications.

  11. Question 11Type I - Small Appliances

    A technician recovers R-134a from a customer's refrigerator. Which use of that refrigerant is allowed without sending it to a reclaimer?

    1. Charging it into a different customer's refrigerator
    2. Storing it long-term in a disposable cylinder
    3. Returning it to the same refrigerator Correct answer.
    4. Selling it to another certified technician

    Explanation

    Recovered refrigerant may be reused without reclamation only in the appliance it came from or in another appliance owned by the same person. Any other use requires reclaiming to ARI 700 purity.

  12. Question 12Type I - Small Appliances

    How should a blended refrigerant such as R-410A be charged into a small appliance?

    1. As a vapor to prevent compressor slugging
    2. As a vapor through the suction service port
    3. As a liquid to prevent fractionation Correct answer.
    4. As a gas after warming the cylinder

    Explanation

    Blends are mixtures whose components have different boiling points, so vapor charging draws off the components unevenly and changes the mixture. They must be removed from the cylinder as a liquid so the original composition is maintained.

  13. Question 13Type I - Small Appliances

    Which instrument confirms that a system has been evacuated to the required level?

    1. A water manometer
    2. A micron gauge Correct answer.
    3. A psychrometer
    4. A compound gauge

    Explanation

    A micron gauge measures deep vacuum in microns, which is far below the resolution of ordinary pressure gauges. Manifold gauges cannot indicate whether the required vacuum level has actually been reached.

  14. Question 14Type I - Small Appliances

    Which gas should be used to pressure-test a small appliance after a repair?

    1. Acetylene
    2. Oxygen
    3. Dry nitrogen Correct answer.
    4. Compressed air

    Explanation

    Dry nitrogen is inert and is applied through a pressure regulator for leak-checking and pressure testing. Oxygen, air, and fuel gases can explode or burn when combined with refrigerant oil and heat.

  15. Question 15Type I - Small Appliances

    Which method is appropriate for locating a small refrigerant leak on an HFC-134a appliance?

    1. A water-filled U-tube manometer
    2. A halide torch flame test
    3. A sling psychrometer reading
    4. An electronic leak detector Correct answer.

    Explanation

    Electronic leak detectors are designed to sense HFC refrigerants at low concentrations. Halide torches are intended for CFC and HCFC refrigerants and are not suitable for HFCs.

  16. Question 16Type I - Small Appliances

    Recovery equipment intended for use on small appliances must be certified by

    1. the refrigerant supplier
    2. an EPA-approved testing organization Correct answer.
    3. the local municipal building department
    4. the appliance manufacturer

    Explanation

    Recovery and recycling equipment must be tested and certified by an organization approved by EPA to verify that it meets the required recovery efficiency. Manufacturer, municipal, or supplier approval does not satisfy this requirement.

  17. Question 17Type I - Small Appliances

    Why should the appliance's own compressor never be used as a vacuum pump?

    1. It adds too much oil to the system
    2. It removes the refrigerant too quickly
    3. It voids the appliance warranty
    4. It cannot pull a deep vacuum and may overheat Correct answer.

    Explanation

    A refrigeration compressor is designed to pump vapor against high discharge pressure, not to evacuate a system to a deep vacuum. Running it for evacuation can overheat or damage it and will not reach the required vacuum level.

  18. Question 18Type I - Small Appliances

    A small appliance's compressor will not run, and the refrigerant must still be removed. Which statement is correct?

    1. Recovery is still required and may take longer Correct answer.
    2. The charge may be vented because the compressor is dead
    3. The refrigerant must be burned off on site
    4. Recovery is unnecessary because the charge is trapped in the condenser

    Explanation

    The recovery requirement applies whether or not the compressor operates. A non-running compressor means the system cannot help move refrigerant, so recovery with the recovery machine may take more time and care.

  19. Question 19Type I - Small Appliances

    A recovery cylinder contains refrigerant that may be a mixture of two different refrigerants. What should be done with it?

    1. Ship it to an EPA-certified refrigerant reclaimer Correct answer.
    2. Charge it into any appliance that uses one of the refrigerants
    3. Blend it with virgin refrigerant to restore purity
    4. Vent it to the atmosphere since it cannot be reclaimed

    Explanation

    Mixed refrigerants cannot be separated in the field, so the cylinder must be sent to an EPA-certified reclaimer. Mixing also makes the entire batch unreclaimable, so different refrigerants must always be kept in separate cylinders.

  20. Question 20Type I - Small Appliances

    How often must a DOT recovery cylinder be hydrostatically tested?

    1. Every year
    2. Every 10 years
    3. Every 5 years Correct answer.
    4. Only when it is damaged

    Explanation

    Refrigerant cylinders are DOT-specified pressure vessels that must be requalified by hydrostatic test every 5 years. A cylinder past its test date may not be filled.

  21. Question 21Type I - Small Appliances

    When a CFC refrigerant contacts an open flame, which toxic gas can be formed?

    1. Sulfur dioxide
    2. Hydrogen sulfide
    3. Carbon monoxide
    4. Phosgene Correct answer.

    Explanation

    Heating CFC refrigerants with a torch decomposes them into phosgene, a highly toxic gas; HFCs break down into hydrogen fluoride. Lines should be evacuated and purged before any brazing.

  22. Question 22Type I - Small Appliances

    Why is a refrigerant leak in a basement mechanical room a serious hazard?

    1. It reacts with concrete to form corrosive acid
    2. It raises the room pressure to a dangerous level
    3. It is heavier than air and can displace oxygen Correct answer.
    4. It ignites easily at low concentrations

    Explanation

    Refrigerant vapor is denser than air and settles in low areas such as basements and pits, displacing the oxygen supply. Ventilation and monitoring are needed before entering such spaces.

  23. Question 23Type I - Small Appliances

    A frost-free refrigerator has a leaking evaporator that cannot be repaired. What is the correct action?

    1. Recover the charge, then scrap the appliance Correct answer.
    2. Drain the oil and scrap it without recovering
    3. Seal the leak with epoxy and resell the unit
    4. Vent the remaining charge, then scrap the unit

    Explanation

    Refrigerant must be recovered before an appliance is opened, dismantled, or discarded, even when the unit is being destroyed. Venting during disposal is prohibited.

  24. Question 24Type I - Small Appliances

    Why must a recovery cylinder never be filled completely with liquid refrigerant?

    1. The cylinder gauge will read inaccurately
    2. Liquid refrigerant will not flow out of the valve
    3. Liquid expansion can rupture the cylinder Correct answer.
    4. The refrigerant will decompose under pressure

    Explanation

    Liquid refrigerant expands significantly as it warms, and with no vapor space the pressure can rise until the cylinder fails. Filling by weight to no more than 80 percent keeps a vapor space for expansion.

  25. Question 25Type I - Small Appliances

    How must polyolester (POE) oil used with HFC refrigerants be handled?

    1. Stored in open containers so acids can escape
    2. Mixed with mineral oil before use
    3. Replaced after every service call
    4. Kept sealed because it absorbs moisture quickly Correct answer.

    Explanation

    POE oil is hygroscopic and takes on moisture from the air rapidly, which can lead to acid formation and system damage. Containers should be kept closed and opened only briefly during use.

  26. Question 26Type I - Small Appliances

    Under Section 608, what is the maximum refrigerant charge, in pounds, that defines a small appliance?

    1. 10 pounds
    2. 15 pounds
    3. 25 pounds
    4. 5 pounds Correct answer.

    Explanation

    A small appliance is defined as an appliance containing 5 pounds or less of refrigerant, excluding motor vehicle air conditioners. Any charge above that threshold falls under a different servicing category.

  27. Question 27Type I - Small Appliances

    Which certification category must a technician hold to service a small appliance containing 5 pounds or less of refrigerant?

    1. Type II
    2. Type III
    3. Type I Correct answer.
    4. Universal

    Explanation

    Type I certification covers the servicing of small appliances. Type II covers high-pressure appliances, Type III covers low-pressure appliances, and Universal covers all categories.

  28. Question 28Type I - Small Appliances

    Which refrigerant is classified as a chlorofluorocarbon (CFC)?

    1. R-410A
    2. R-134a
    3. R-22
    4. R-12 Correct answer.

    Explanation

    R-12 contains chlorine and fluorine and is classified as a CFC. R-22 is an HCFC, while R-134a and R-410A are HFCs.

  29. Question 29Type I - Small Appliances

    What color identifies the top of a recovery cylinder used for recovered refrigerant?

    1. Green
    2. Red
    3. Gray
    4. Yellow Correct answer.

    Explanation

    Recovery cylinders generally have a gray body and a yellow top. The yellow top signals that the cylinder is intended for recovered refrigerant.

  30. Question 30Type I - Small Appliances

    Before a household refrigerator is scrapped, what must be done with the refrigerant?

    1. Burn it
    2. Vent it
    3. Dilute it with water
    4. Recover it Correct answer.

    Explanation

    Refrigerant must be recovered before an appliance is dismantled or discarded. Knowingly venting refrigerant to the atmosphere is prohibited under Section 608.

  31. Question 31Type I - Small Appliances

    Which lubricant is commonly used with HFC-134a in small appliances?

    1. Silicone oil
    2. Polyolester oil Correct answer.
    3. Castor oil
    4. Mineral oil

    Explanation

    HFC refrigerants such as R-134a generally require polyolester (POE) lubricant. Mineral oil is typically used with CFC and HCFC refrigerants.

  32. Question 32Type I - Small Appliances

    What does Section 608 prohibit when servicing a small appliance?

    1. Using a gauge manifold
    2. Knowingly venting refrigerant Correct answer.
    3. Using a vacuum pump
    4. Using a recovery cylinder

    Explanation

    Section 608 prohibits knowingly venting ozone-depleting refrigerants and their substitutes during service, maintenance, repair, or disposal. Recovery equipment must be used instead.

  33. Question 33Type I - Small Appliances

    What is the maximum percentage of a recovery cylinder that may be filled with liquid refrigerant?

    1. 80 percent Correct answer.
    2. 90 percent
    3. 95 percent
    4. 100 percent

    Explanation

    A recovery cylinder must never be filled beyond 80 percent of its capacity by weight. Leaving vapor space allows for liquid expansion as the cylinder warms.

  34. Question 34Type I - Small Appliances

    A technician recovers refrigerant from a small appliance manufactured before November 15, 1993, without evacuating to 4 inches Hg. What minimum percentage of the charge must be recovered?

    1. 80 percent Correct answer.
    2. 70 percent
    3. 50 percent
    4. 90 percent

    Explanation

    For pre-1993 small appliances, the technician must recover at least 80 percent of the refrigerant charge or evacuate the system to 4 inches Hg vacuum. Recovery to a lower percentage does not meet the requirement.

  35. Question 35Type I - Small Appliances

    For a small appliance manufactured after November 15, 1993, what minimum percentage of refrigerant must be recovered if the system is not evacuated to 4 inches Hg?

    1. 90 percent Correct answer.
    2. 70 percent
    3. 100 percent
    4. 80 percent

    Explanation

    Post-1993 small appliances require recovery of at least 90 percent of the charge unless the system is evacuated to 4 inches Hg. The higher percentage reflects the newer equipment standard.

  36. Question 36Type I - Small Appliances

    When system-dependent recovery equipment is used on a small appliance manufactured after November 15, 1993, to what vacuum must the system be evacuated?

    1. 20 inches Hg
    2. 10 inches Hg Correct answer.
    3. 4 inches Hg
    4. 0 inches Hg

    Explanation

    System-dependent recovery equipment on post-1993 small appliances must evacuate the system to 10 inches Hg vacuum. This is a lower vacuum than the 4 inches Hg requirement for pre-1993 appliances.

  37. Question 37Type I - Small Appliances

    When system-dependent recovery equipment is used on a pre-1993 small appliance, what is the required evacuation level?

    1. 4 inches Hg Correct answer.
    2. 10 inches Hg
    3. 20 inches Hg
    4. 0 inches Hg

    Explanation

    Pre-1993 small appliances using system-dependent recovery equipment must be evacuated to 4 inches Hg vacuum. Post-1993 appliances have a different system-dependent requirement.

  38. Question 38Type I - Small Appliances

    A recovery cylinder has reached 80 percent of its capacity by weight. What should the technician do?

    1. Stop recovery and use another cylinder Correct answer.
    2. Cool the cylinder and keep filling
    3. Vent excess refrigerant to make room
    4. Continue until the cylinder is full

    Explanation

    Recovery must stop at 80 percent capacity by weight so the cylinder has room for liquid expansion. The remaining refrigerant should be directed into another recovery cylinder.

  39. Question 39Type I - Small Appliances

    How should a recovery cylinder be transported in a service vehicle?

    1. Lying unsecured in the trunk
    2. On its side in the passenger cab
    3. In the passenger seat with a seatbelt
    4. Secured upright in the cargo area Correct answer.

    Explanation

    Recovery cylinders should be secured upright in the cargo area so the valve is protected and the cylinder cannot roll. They should not be carried loose or in the passenger compartment.

  40. Question 40Type I - Small Appliances

    What is the purpose of a filter-drier installed on a recovery machine?

    1. Increase recovery speed
    2. Remove moisture and acids Correct answer.
    3. Measure vacuum level
    4. Cool the refrigerant

    Explanation

    A filter-drier removes moisture, acids, and particulate contamination from refrigerant passing through the recovery machine. This helps protect the recovery equipment and the refrigerant quality.

  41. Question 41Type I - Small Appliances

    For what situation is a recovery bag designed?

    1. Systems containing more than 15 pounds
    2. Sealed units with a dead compressor Correct answer.
    3. Large commercial chillers and racks
    4. Motor vehicle air-conditioning systems

    Explanation

    A recovery bag is used on non-pressurized small appliances that have no service ports and an inoperative compressor. It captures refrigerant that cannot be removed with system-dependent equipment.

  42. Question 42Type I - Small Appliances

    When adding refrigerant vapor to a small appliance, where should it be introduced?

    1. Into the discharge line before the condenser
    2. Into the compressor oil sump
    3. Into the liquid line while the system is off
    4. Into the suction line while the system runs Correct answer.

    Explanation

    Vapor refrigerant should be charged into the suction line with the system operating so the compressor does not slug liquid. Liquid charging is handled differently and depends on the refrigerant type.

  43. Question 43Type I - Small Appliances

    Before recovering refrigerant from a small appliance of unknown service history, what should the technician do first?

    1. Identify the refrigerant Correct answer.
    2. Evacuate the system
    3. Add nitrogen to the system
    4. Heat the recovery cylinder

    Explanation

    The refrigerant should be identified before recovery so it is not mixed with a different refrigerant in the recovery cylinder. A refrigerant identifier can determine the type and help detect contamination.

  44. Question 44Type I - Small Appliances

    What leak repair requirement does Section 608 impose on small appliances?

    1. No mandatory leak repair Correct answer.
    2. Repair within 7 days
    3. Repair only if charge exceeds 5 pounds
    4. Repair within 30 days

    Explanation

    The mandatory leak repair requirements apply to appliances containing 50 or more pounds of refrigerant. Small appliances are not subject to those repair deadlines.

  45. Question 45Type I - Small Appliances

    What is the maximum temperature to which a recovery cylinder should be heated?

    1. 125 degrees F Correct answer.
    2. 200 degrees F
    3. 175 degrees F
    4. 150 degrees F

    Explanation

    A recovery cylinder should never be heated above 125 degrees F. Warm water or a gentle heating blanket may be used, but an open flame or excessive heat is unsafe.

  46. Question 46Type I - Small Appliances

    A technician allows a small amount of refrigerant to escape while connecting gauges to a small appliance. Which statement best describes the EPA requirement?

    1. Any release is allowed during repair
    2. Release is allowed for R-134a but not for R-12
    3. Release is allowed if it is under 1 pound
    4. Knowing venting is prohibited and connections must minimize release Correct answer.

    Explanation

    Section 608 prohibits knowingly venting refrigerant, and service practices must minimize releases. Low-loss fittings and proper hose handling reduce the amount released during gauge connections.

  47. Question 47Type I - Small Appliances

    Refrigerant recovered from a small appliance with a burned-out compressor should be handled how?

    1. Vented if the quantity is small
    2. Recycled or reclaimed with filtration before reuse Correct answer.
    3. Returned directly to the same appliance
    4. Mixed with other refrigerant in a recovery cylinder

    Explanation

    A compressor burnout can leave acids and particulate contamination in the refrigerant. The recovered refrigerant should be cleaned through recycling or reclaiming before it is reused.

  48. Question 48Type I - Small Appliances

    What distinguishes a DOT recovery cylinder from a disposable refrigerant cylinder?

    1. Disposable cylinders are always yellow
    2. Recovery cylinders can be refilled and require hydrostatic testing Correct answer.
    3. Disposable cylinders can be refilled if labeled
    4. Recovery cylinders are never tested

    Explanation

    DOT recovery cylinders are designed to be refilled and must be hydrostatically tested on a required schedule. Disposable cylinders are not intended to be refilled.

  49. Question 49Type I - Small Appliances

    Why must HFC refrigerants be recovered rather than vented even though they do not deplete stratospheric ozone?

    1. They are flammable
    2. They are toxic to plants
    3. They have high global warming potential Correct answer.
    4. They react with nitrogen in the air

    Explanation

    HFCs are ozone-friendly compared with CFCs, but they are potent greenhouse gases with high global warming potential. Section 608 therefore prohibits knowingly venting them.

  50. Question 50Type I - Small Appliances

    A technician must recover refrigerant from a sealed small appliance that has no service ports. Which approach is appropriate?

    1. Use the appliance compressor as a vacuum pump
    2. Install access fittings or use a recovery bag Correct answer.
    3. Vent the charge to the atmosphere
    4. Fill the system with nitrogen and release the mixture

    Explanation

    When no service ports exist, the technician must gain access by installing fittings or use equipment designed for sealed systems, such as a recovery bag. The refrigerant must still be captured rather than released.

  51. Question 51Type II - High-Pressure Appliances

    Type II certification is required for technicians who maintain, service, repair, or dispose of which equipment?

    1. Motor vehicle air-conditioning systems
    2. Small appliances containing 5 pounds or less of refrigerant
    3. Low-pressure appliances such as R-123 centrifugal chillers
    4. High-pressure appliances using HCFC or HFC refrigerants Correct answer.

    Explanation

    Type II covers high-pressure appliances, which use refrigerants such as R-22, R-410A, and R-404A. Motor vehicle work falls under Section 609, small appliances under Type I, and low-pressure equipment under Type III.

  52. Question 52Type II - High-Pressure Appliances

    By weight, a recovery cylinder should be filled with refrigerant to a maximum of:

    1. 95% of its capacity
    2. 90% of its capacity
    3. 80% of its capacity Correct answer.
    4. 60% of its capacity

    Explanation

    Recovery cylinders must not be filled above 80% of capacity by weight so that there is room for the liquid to expand as the cylinder warms. Exceeding that limit risks hydraulic rupture or release through the relief device.

  53. Question 53Type II - High-Pressure Appliances

    A technician is evacuating a high-pressure appliance containing R-22 using recovery equipment built after November 15, 1993. The refrigerant must be removed down to:

    1. 25 inches of mercury vacuum
    2. 10 inches of mercury vacuum
    3. 15 inches of mercury vacuum
    4. 0 inches of mercury vacuum Correct answer.

    Explanation

    Under Table 1 to 40 CFR 82.156, R-22 in a high-pressure appliance must be evacuated to 0 inches of mercury vacuum when recovery equipment manufactured on or after November 15, 1993 is used.

  54. Question 54Type II - High-Pressure Appliances

    Before a high-pressure appliance's refrigerant circuit is opened to the atmosphere for repair, the technician must:

    1. Close the service valves and vent the remaining charge
    2. Recover the refrigerant to the required vacuum level Correct answer.
    3. Purge the lines with refrigerant vapor
    4. Blow the charge out with dry nitrogen

    Explanation

    Section 608 requires refrigerant to be recovered to the required evacuation level before an appliance is opened, so that no refrigerant is released to the atmosphere.

  55. Question 55Type II - High-Pressure Appliances

    An owner of an appliance containing 50 or more pounds of refrigerant learns that the appliance has exceeded its leak-rate threshold. The leak must be repaired within:

    1. 30 days Correct answer.
    2. 10 days
    3. 45 days
    4. 6 months

    Explanation

    40 CFR 82.157 requires the owner or operator to repair a leak that exceeds the applicable leak-rate threshold within 30 days of discovery.

  56. Question 56Type II - High-Pressure Appliances

    When charging a system with a blended refrigerant such as R-410A, the refrigerant should be:

    1. Removed from the cylinder as a vapor
    2. Removed from the cylinder only after the cylinder is warmed to 100°F
    3. Removed from the cylinder through a moisture indicator
    4. Removed from the cylinder as a liquid Correct answer.

    Explanation

    Blends can fractionate when vapor is drawn off, so the cylinder charge must be withdrawn as a liquid to keep the mixture's composition correct.

  57. Question 57Type II - High-Pressure Appliances

    Compared with a system using R-22 at the same operating conditions, an R-410A system operates at pressures that are roughly:

    1. About the same
    2. Three to four times higher
    3. 50 to 60% higher Correct answer.
    4. 20% lower

    Explanation

    R-410A runs about 50 to 60% higher pressures than R-22, which is why hoses, gauges, recovery machines, and cylinders must be rated for R-410A service.

  58. Question 58Type II - High-Pressure Appliances

    Liquid refrigerant that contacts a technician's skin will most likely cause:

    1. Frostbite or a cold burn Correct answer.
    2. No injury, because the liquid evaporates instantly
    3. A mild rash that clears in a few hours
    4. Chemical poisoning through the skin

    Explanation

    Liquid refrigerant boils at a very low temperature and can freeze tissue on contact. Gloves and goggles should always be worn when handling refrigerant.

  59. Question 59Type II - High-Pressure Appliances

    Using recovery equipment manufactured after November 15, 1993, an appliance charged with R-410A must be evacuated to:

    1. 5 inches of mercury vacuum
    2. 10 inches of mercury vacuum Correct answer.
    3. 0 inches of mercury vacuum
    4. 25 inches of mercury vacuum

    Explanation

    R-410A falls under the 10 inches of mercury vacuum requirement in Table 1 to 40 CFR 82.156 when post-1993 recovery equipment is used.

  60. Question 60Type II - High-Pressure Appliances

    After a required leak repair is completed on a high-pressure appliance, the follow-up verification test must be performed:

    1. Within 10 days after the initial verification test Correct answer.
    2. Only if a new leak is later discovered
    3. Within 90 days of completing the repair
    4. Within 24 hours of completing the repair

    Explanation

    The repair is first confirmed with an initial verification test, and a follow-up verification test must then be conducted within 10 days after the initial verification test.

  61. Question 61Type II - High-Pressure Appliances

    The leak repair and verification requirements of 40 CFR 82.157 apply to appliances that contain:

    1. 500 or more pounds of refrigerant
    2. Any amount of refrigerant
    3. 50 or more pounds of refrigerant Correct answer.
    4. 5 or more pounds of refrigerant

    Explanation

    Subpart F leak repair provisions apply to appliances containing 50 or more pounds of a class I or class II refrigerant or a substitute.

  62. Question 62Type II - High-Pressure Appliances

    A technician needs to pressure test a repaired R-22 line set for leaks. The correct medium is:

    1. Compressed air from a shop compressor
    2. Dry nitrogen through a pressure regulator Correct answer.
    3. Oxygen from a welding cylinder
    4. Refrigerant vapor from the recovery cylinder

    Explanation

    Dry nitrogen is the accepted inert gas for pressure testing. Air introduces moisture and oil, oxygen can explode on contact with oil, and refrigerant should never be used as a purge or test gas.

  63. Question 63Type II - High-Pressure Appliances

    A technician plans to braze a joint on an R-22 system that has not yet had its charge recovered. The main hazard is:

    1. Loss of the compressor's entire oil charge
    2. Freezing of the copper tubing by escaping liquid
    3. Spontaneous ignition of the refrigerant vapor
    4. Formation of phosgene gas at the joint Correct answer.

    Explanation

    Heating a chlorine-containing refrigerant to high temperature in the presence of air produces phosgene, a highly toxic gas. The system must be recovered and purged with nitrogen before any brazing.

  64. Question 64Type II - High-Pressure Appliances

    Which of the following is true about disposable (non-refillable) refrigerant cylinders?

    1. They may be refilled after a hydrostatic test
    2. They may be refilled once with the same refrigerant
    3. They may be used as recovery cylinders if relabeled
    4. They must never be refilled Correct answer.

    Explanation

    DOT non-refillable cylinders are designed and tested for a single fill only. Refilling them is unsafe and prohibited, and relabeling does not change that.

  65. Question 65Type II - High-Pressure Appliances

    Before using a refillable recovery cylinder, a technician should verify that:

    1. Its working pressure rating is 100 psig or less
    2. It has been painted white
    3. It has been purged with shop air
    4. Its hydrostatic test date has not passed Correct answer.

    Explanation

    DOT refillable cylinders must be hydrostatically retested at required intervals, commonly every five years for 4BA and 4BW cylinders. A cylinder with an expired test date must be taken out of service.

  66. Question 66Type II - High-Pressure Appliances

    Recovery and recycling equipment used on high-pressure appliances must be:

    1. Certified by an EPA-approved lab Correct answer.
    2. Rated for at least 5 tons of cooling capacity
    3. Replaced every three years
    4. Registered with the local fire marshal

    Explanation

    Section 608 requires recovery and recycling equipment to be certified by an EPA-approved third-party testing organization to meet the applicable equipment standard.

  67. Question 67Type II - High-Pressure Appliances

    A system-dependent recovery device cannot be used to evacuate an appliance when:

    1. The appliance uses R-22
    2. The outdoor ambient is below 90°F
    3. The appliance's compressor is not operating Correct answer.
    4. The appliance is more than 10 years old

    Explanation

    System-dependent recovery relies on the appliance's own compressor and normal pressures to move refrigerant, so it will not work if the compressor is inoperative.

  68. Question 68Type II - High-Pressure Appliances

    Using refrigerant to purge air from a refrigeration system's lines is:

    1. Required after any brazed repair
    2. Acceptable only on R-410A systems
    3. Prohibited, since it vents refrigerant to the air Correct answer.
    4. Acceptable if the refrigerant is recovered afterward

    Explanation

    Purging with refrigerant deliberately releases it to the atmosphere, which Section 608 prohibits. Dry nitrogen is used for purging instead.

  69. Question 69Type II - High-Pressure Appliances

    Which precaution applies when connecting manifold gauges to an R-410A system?

    1. Use gauges and hoses rated for R-410A pressures Correct answer.
    2. Reduce system pressure to 0 psig before connecting
    3. Use R-22 gauge sets because the threads are identical
    4. Apply vacuum pump oil to the fittings first

    Explanation

    R-410A's higher pressures can rupture hoses and gauges that are not rated for it, so only equipment listed for R-410A service should be used.

  70. Question 70Type II - High-Pressure Appliances

    Refrigerant that has been removed from a customer's appliance and will be sold to another party must be:

    1. Reclaimed to AHRI 700 by a certified reclaimer Correct answer.
    2. Recycled on site and sold in a new cylinder
    3. Labeled as recovered refrigerant and sold as is
    4. Vented, because it is a blended refrigerant

    Explanation

    Refrigerant that is sold or transferred must be reclaimed to AHRI Standard 700 by an EPA-certified reclaimer. On-site recycling is only acceptable for reuse in the same equipment.

  71. Question 71Type II - High-Pressure Appliances

    A high-pressure appliance holds a 120-pound charge. Over the past 12 months, the owner added 14.4 pounds of refrigerant to keep it operating. The annual leak rate is:

    1. 8.3%
    2. 12.0% Correct answer.
    3. 14.4%
    4. 10.0%

    Explanation

    The leak rate equals the refrigerant added over the past 12 months divided by the appliance's full charge, times 100: (14.4 divided by 120) times 100 = 12%.

  72. Question 72Type II - High-Pressure Appliances

    If a follow-up verification test shows that a required leak repair on a high-pressure appliance was not successful, the owner must:

    1. Apply to the EPA for a permanent exemption
    2. Perform a third verification test within 90 days
    3. Add leak sealant and continue operating
    4. Retrofit or retire the appliance Correct answer.

    Explanation

    When the verification tests show the appliance still exceeds the leak-rate threshold, the appliance must be retrofitted or retired rather than continuing to leak.

  73. Question 73Type II - High-Pressure Appliances

    Refrigerant is being recovered from a high-pressure system that suffered a compressor burnout. The recovered refrigerant:

    1. May be recharged into another customer's system after recycling on site
    2. Can be reused in the same system without treatment
    3. Must be vented because it is contaminated
    4. Recovered through a filter-drier into a separate cylinder Correct answer.

    Explanation

    Burnout refrigerant carries acids, moisture, and particulate, so it is recovered through a filter-drier into its own labeled cylinder and sent to a certified reclaimer. It may not be reused in other equipment.

  74. Question 74Type II - High-Pressure Appliances

    To speed recovery from a high-pressure appliance with a large liquid charge, a technician should first:

    1. Recover vapor from the top of the receiver
    2. Pull a deep vacuum on the system
    3. Warm the evaporator with a heat gun
    4. Recover liquid from the liquid line Correct answer.

    Explanation

    Removing liquid first moves the bulk of the charge quickly. Recovering vapor first takes much longer and leaves most of the refrigerant in the system.

  75. Question 75Type II - High-Pressure Appliances

    Liquid refrigerant should not be charged into the suction line of a running compressor because:

    1. The refrigerant will be too warm to blend properly
    2. It will raise the discharge pressure above the relief setting
    3. The system's oil will polymerize in the crankcase
    4. Liquid can slug the compressor and damage the valves Correct answer.

    Explanation

    Compressors are designed to pump vapor. Liquid entering the suction can cause slugging, broken valves, and bearing damage, so liquid is charged into the liquid line or throttled in as vapor.

  76. Question 76Type II - High-Pressure Appliances

    Which of the following appliances is classified as a high-pressure appliance under EPA Section 608 regulations?

    1. A centrifugal chiller using R-123
    2. A household refrigerator using R-134a
    3. A window air-conditioning unit using R-22
    4. A supermarket rack using R-404A Correct answer.

    Explanation

    High-pressure appliances include those using refrigerants such as R-22, R-404A, and R-410A, typically commercial refrigeration and air-conditioning systems. R-123 is a low-pressure refrigerant used in centrifugal chillers. Household refrigerators and window units are small appliances, not Type II high-pressure appliances.

  77. Question 77Type II - High-Pressure Appliances

    For a high-pressure commercial refrigeration appliance, the owner must repair a leak when the annual leak rate exceeds:

    1. 15 percent
    2. 30 percent
    3. 20 percent Correct answer.
    4. 10 percent

    Explanation

    EPA leak repair thresholds are 20% for commercial refrigeration, 10% for comfort cooling, and 30% for industrial process refrigeration. Exceeding 20% triggers repair requirements.

  78. Question 78Type II - High-Pressure Appliances

    Recovery equipment manufactured before November 15, 1993 may evacuate a high-pressure appliance only to:

    1. 15 inches of mercury vacuum
    2. 500 microns
    3. 10 inches of mercury vacuum
    4. 0 psig Correct answer.

    Explanation

    Equipment manufactured before that date is only required to evacuate high-pressure appliances to 0 psig. Equipment made after that date must reach deeper vacuum levels depending on charge size.

  79. Question 79Type II - High-Pressure Appliances

    When pressure testing a high-pressure appliance with nitrogen, the technician should:

    1. Heat the system while applying full cylinder pressure
    2. Use oxygen instead to speed the test
    3. Connect the nitrogen cylinder directly to the system
    4. Use a pressure regulator on the nitrogen cylinder Correct answer.

    Explanation

    Nitrogen is supplied at high cylinder pressure, so a pressure regulator is required to prevent overpressurizing the appliance. Oxygen must never be used because it can cause explosions with oil.

  80. Question 80Type II - High-Pressure Appliances

    A refillable refrigerant recovery cylinder is typically color-coded with:

    1. A white body and blue top
    2. An orange body and black top
    3. A green body and red top
    4. A gray body and yellow top Correct answer.

    Explanation

    DOT recovery cylinders are commonly gray with a yellow top to identify them for refrigerant recovery. This color coding helps prevent misuse of the cylinder.

  81. Question 81Type II - High-Pressure Appliances

    Which refrigerant is a high-pressure refrigerant commonly used in Type II appliances?

    1. R-718
    2. R-11
    3. R-123
    4. R-22 Correct answer.

    Explanation

    R-22 is a high-pressure refrigerant used in many commercial refrigeration and air-conditioning appliances. R-123 and R-11 are low-pressure refrigerants, and R-718 is water.

  82. Question 82Type II - High-Pressure Appliances

    A recovery cylinder should never be filled to more than what percentage of its capacity by volume?

    1. 80 percent Correct answer.
    2. 60 percent
    3. 95 percent
    4. 70 percent

    Explanation

    Recovery cylinders must be filled to no more than 80% by volume to allow for liquid expansion and prevent hydrostatic rupture. Overfilling is a serious safety hazard.

  83. Question 83Type II - High-Pressure Appliances

    Using recovery equipment manufactured after November 15, 1993, a high-pressure appliance with a charge of 250 pounds must be evacuated to:

    1. 10 inches of mercury vacuum
    2. 15 inches of mercury vacuum Correct answer.
    3. 29 inches of mercury vacuum
    4. 0 psig

    Explanation

    For high-pressure appliances with 200 pounds or more of charge, post-1993 recovery equipment must evacuate to 15 inches of mercury vacuum. Smaller charges require 10 inches of mercury vacuum.

  84. Question 84Type II - High-Pressure Appliances

    The leak repair threshold for industrial process refrigeration is:

    1. 30 percent Correct answer.
    2. 50 percent
    3. 10 percent
    4. 20 percent

    Explanation

    Industrial process refrigeration has a 30% annual leak rate threshold. Commercial refrigeration is 20% and comfort cooling is 10%.

  85. Question 85Type II - High-Pressure Appliances

    A high-pressure comfort-cooling appliance has a 100-pound charge and leaks 12 pounds in 12 months. What is required?

    1. The appliance must be retired immediately
    2. Only a follow-up verification test is required
    3. Repair the leak because it exceeds 10 percent Correct answer.
    4. No action because the leak is below 20 percent

    Explanation

    Comfort cooling has a 10% leak rate threshold, and 12 pounds out of 100 pounds is 12%, which exceeds it. The owner must repair the leak and follow verification requirements.

  86. Question 86Type II - High-Pressure Appliances

    Refrigerant that has been recovered and recycled may be reused in:

    1. A small appliance only
    2. The same appliance it was removed from Correct answer.
    3. A certified refrigerant sales facility only
    4. Any appliance owned by a different company

    Explanation

    Recycled refrigerant may be returned to the same appliance or another appliance owned by the same owner. If it is sold or transferred to another owner, it must be reclaimed.

  87. Question 87Type II - High-Pressure Appliances

    Before a high-pressure appliance is dismantled and disposed of, the technician must:

    1. Add nitrogen to the system
    2. Vent the refrigerant to the atmosphere
    3. Recover the refrigerant charge Correct answer.
    4. Remove the compressor only

    Explanation

    EPA requires recovery of refrigerant before appliance disposal or dismantling. Venting is prohibited for ozone-depleting and substitute refrigerants.

  88. Question 88Type II - High-Pressure Appliances

    When transferring recovered refrigerant, the cylinder used must be:

    1. A DOT-approved recovery cylinder Correct answer.
    2. A disposable cylinder
    3. Any cylinder labeled for oxygen service
    4. A cylinder with no relief valve

    Explanation

    Refrigerant recovery cylinders must meet DOT specifications and be approved for refrigerant service. Disposable cylinders cannot be used for recovery.

  89. Question 89Type II - High-Pressure Appliances

    A micron gauge is used during evacuation to measure:

    1. System pressure above atmospheric
    2. Oil pressure
    3. Refrigerant charge weight
    4. Vacuum level in microns Correct answer.

    Explanation

    A micron gauge measures deep vacuum in microns of mercury, which is far more accurate than a manifold gauge for evacuation. It verifies that moisture and air have been removed.

  90. Question 90Type II - High-Pressure Appliances

    Why is vapor recovery from a high-pressure appliance generally slower than liquid recovery?

    1. Vapor contains more oil
    2. Vapor has a much higher boiling point than liquid
    3. Vapor is less dense and has less mass per volume Correct answer.
    4. Vapor cannot be compressed

    Explanation

    Vapor recovery moves less refrigerant mass per unit of volume, so it takes longer than removing liquid. Liquid recovery is preferred when a large charge is present.

  91. Question 91Type II - High-Pressure Appliances

    When retrofitting a high-pressure R-22 appliance to a different refrigerant, the technician should first:

    1. Recover the old refrigerant and evacuate Correct answer.
    2. Add a larger compressor
    3. Vent the R-22 to make room
    4. Charge the new refrigerant on top of the old charge

    Explanation

    Retrofitting requires recovery of the old refrigerant, evacuation, and typically replacement of the filter-drier before charging the new refrigerant. Mixing refrigerants is not allowed.

  92. Question 92Type II - High-Pressure Appliances

    Records of refrigerant purchase and use for a high-pressure appliance must be kept for at least:

    1. 3 years Correct answer.
    2. 5 years
    3. 1 year
    4. 2 years

    Explanation

    EPA Section 608 requires owners and technicians to retain refrigerant records for three years. This supports leak rate calculations and compliance checks.

  93. Question 93Type II - High-Pressure Appliances

    If a recovery cylinder becomes warm during recovery, the technician should expect:

    1. The cylinder to empty faster
    2. Pressure to rise and recovery to slow Correct answer.
    3. Recovery to speed up
    4. The refrigerant to become flammable

    Explanation

    Warming the cylinder raises internal pressure, which reduces the pressure difference driving refrigerant into the cylinder and slows recovery. Cooling the cylinder helps.

  94. Question 94Type II - High-Pressure Appliances

    Which practice is acceptable when recovering refrigerant from a high-pressure appliance?

    1. Using a vacuum pump alone to recover refrigerant
    2. Using a machine rated for the refrigerant Correct answer.
    3. Venting the last few ounces
    4. Discharging refrigerant into a drain

    Explanation

    Recovery machines must be compatible with the refrigerant being recovered. Vacuum pumps are for evacuation, not recovery, and venting is prohibited.

  95. Question 95Type II - High-Pressure Appliances

    A 400-pound industrial process refrigeration appliance loses 100 pounds of refrigerant over 12 months. What is the leak rate and required action?

    1. 25 percent; repair is required
    2. 25 percent; no repair needed Correct answer.
    3. 20 percent; repair is required
    4. 10 percent; no repair is required

    Explanation

    100 divided by 400 is 25%, which is below the 30% threshold for industrial process refrigeration, so the leak repair rule is not triggered. The technician should still repair leaks as good practice, but the mandatory threshold is not exceeded.

  96. Question 96Type II - High-Pressure Appliances

    A high-pressure commercial refrigeration appliance has a 250-pound charge. In 12 months, 55 pounds are added. What is required under EPA leak repair rules?

    1. No action because the rate is below 20 percent
    2. Only add refrigerant and record the amount
    3. Repair the leak and verify the repair Correct answer.
    4. Retire the appliance within 30 days

    Explanation

    55 divided by 250 is 22%, which exceeds the 20% commercial refrigeration threshold. The owner must repair the leak and perform verification testing.

  97. Question 97Type II - High-Pressure Appliances

    A technician cannot evacuate a high-pressure appliance to the required vacuum level because the appliance has a leak. The technician should:

    1. Vent the remaining refrigerant
    2. Document the leak and recover to the extent possible Correct answer.
    3. Use a system-dependent recovery device for the appliance
    4. Abandon the appliance without recovery

    Explanation

    If required evacuation cannot be achieved due to a leak, the technician must document the situation and still recover refrigerant to the maximum extent possible. Venting is prohibited.

  98. Question 98Type II - High-Pressure Appliances

    When recovering refrigerant from a high-pressure system equipped with a receiver, the technician should first:

    1. Open the system to the atmosphere
    2. Run the compressor to push refrigerant
    3. Recover vapor from the suction line
    4. Recover liquid from the receiver Correct answer.

    Explanation

    The receiver holds the largest liquid volume, so recovering liquid from it first speeds the process. Running the compressor or opening the system is unsafe or illegal.

  99. Question 99Type II - High-Pressure Appliances

    A technician is recovering R-410A from a high-pressure appliance. The recovery equipment must be:

    1. Equipped with a disposable cylinder
    2. Rated for R-410A's higher pressures Correct answer.
    3. The same as equipment used for R-123
    4. A system-dependent device

    Explanation

    R-410A operates at higher pressures than R-22, so recovery equipment, hoses, and cylinders must be rated for R-410A. Using equipment not rated for the pressure is unsafe.

  100. Question 100Type III - Low-Pressure Appliances

    A low-pressure appliance, such as a centrifugal chiller, is defined by the fact that during normal operation it:

    1. operates with its low side below atmospheric pressure Correct answer.
    2. uses only flammable refrigerants
    3. holds a refrigerant charge under 3 pounds
    4. operates with its high side above 400 psig

    Explanation

    Type III equipment is defined by its operating pressure, not by charge size or refrigerant type. A low-pressure chiller normally runs with the evaporator below atmospheric pressure, which is why air and moisture tend to leak inward rather than refrigerant leaking out.

  101. Question 101Type III - Low-Pressure Appliances

    Which appliance may be serviced under EPA Section 608 Type III certification?

    1. a motor vehicle air conditioner
    2. a residential split air conditioner
    3. a centrifugal chiller using R-123 Correct answer.
    4. a supermarket refrigeration rack

    Explanation

    Type III certification covers low-pressure appliances, the category that includes centrifugal chillers using low-pressure refrigerants such as R-11 or R-123. Other equipment falls under Type I, Type II, or the separate motor vehicle rule.

  102. Question 102Type III - Low-Pressure Appliances

    Which of these is a low-pressure refrigerant historically used in large centrifugal chillers?

    1. R-410A
    2. R-11 Correct answer.
    3. R-404A
    4. R-22

    Explanation

    R-11 boils at roughly 75 degrees F at atmospheric pressure, so a chiller using it runs with the evaporator in a vacuum. That sub-atmospheric operating characteristic is what places the machine in the low-pressure category.

  103. Question 103Type III - Low-Pressure Appliances

    The rupture disc on a low-pressure centrifugal chiller is typically designed to burst at about:

    1. 150 psig
    2. 15 psig Correct answer.
    3. 25 in. Hg vacuum
    4. 300 psig

    Explanation

    Low-pressure chiller shells are built to withstand only a few pounds of positive pressure, so the relief device is a rupture disc set near 15 psig. Any procedure that could raise shell pressure, such as nitrogen testing, must stay below that value.

  104. Question 104Type III - Low-Pressure Appliances

    Air and other non-condensables that enter a low-pressure chiller are normally removed by the:

    1. expansion valve
    2. purge unit Correct answer.
    3. oil separator
    4. filter drier

    Explanation

    A purge unit samples the condenser, separates non-condensable gas from refrigerant vapor, vents the air, and returns the refrigerant to the machine. Driers handle moisture and acids, not air.

  105. Question 105Type III - Low-Pressure Appliances

    Because a low-pressure chiller shell is normally in a vacuum, a leaking gasket most often results in:

    1. the oil charge level rising
    2. condenser pressure dropping below normal
    3. refrigerant escaping rapidly to the atmosphere
    4. air and moisture being drawn into the machine Correct answer.

    Explanation

    With the internal pressure below atmospheric, the pressure difference drives air and water vapor into the shell through any opening. That is why a leak often shows up as excessive purging or abnormally high condenser pressure instead of a loss of charge.

  106. Question 106Type III - Low-Pressure Appliances

    Which gas should be used to pressurize a low-pressure chiller for leak testing?

    1. acetylene
    2. compressed air
    3. oxygen
    4. dry nitrogen Correct answer.

    Explanation

    Dry nitrogen is the accepted pressurizing gas because it is inert, introduces no moisture, and will not support combustion. Oxygen or air mixed with refrigerant and oil can ignite or explode under pressure.

  107. Question 107Type III - Low-Pressure Appliances

    A recovery cylinder should never be filled to more than what percentage of its rated capacity by weight?

    1. 100 percent
    2. 80 percent Correct answer.
    3. 90 percent
    4. 60 percent

    Explanation

    The 80 percent rule leaves room for liquid expansion as the cylinder warms, which prevents hydrostatic rupture. Cylinders are filled by weight, not by pressure, because pressure varies with temperature.

  108. Question 108Type III - Low-Pressure Appliances

    Before a low-pressure appliance is opened for repair, its refrigerant must be recovered to a vacuum of at least:

    1. atmospheric pressure (0 psig)
    2. 10 in. Hg vacuum
    3. 5 psig
    4. 25 in. Hg vacuum Correct answer.

    Explanation

    Section 608 requires low-pressure appliances to be evacuated to 25 inches of mercury vacuum before the system is opened. That is a deeper level than the requirements that apply to most high-pressure equipment.

  109. Question 109Type III - Low-Pressure Appliances

    R-11 in a drum at 70 degrees F sits at about atmospheric pressure. To move the charge into a chiller, the technician must:

    1. chill the drum so its pressure drops
    2. warm the drum or pressurize it with nitrogen Correct answer.
    3. connect the drum to the compressor suction
    4. invert the drum and let gravity drain it

    Explanation

    A low-pressure refrigerant at ambient temperature produces almost no positive pressure, so the drum must be warmed or pushed with nitrogen to raise its pressure above the chiller's. Heat must be applied carefully so the shell stays within its pressure limits.

  110. Question 110Type III - Low-Pressure Appliances

    Liquid refrigerant should never be charged directly into the:

    1. receiver
    2. compressor suction service valve Correct answer.
    3. liquid line
    4. evaporator

    Explanation

    Liquid entering the suction side can slug the compressor and damage valves or bearings, so the suction side is charged with vapor. Liquid is charged into the high side or, on a low-pressure chiller, into the evaporator where it flashes before reaching the compressor.

  111. Question 111Type III - Low-Pressure Appliances

    Which reading indicates that non-condensables have accumulated in a low-pressure chiller?

    1. low suction superheat at full load
    2. subcooling below design value
    3. high condenser approach temperature Correct answer.
    4. purge unit running less often than normal

    Explanation

    Non-condensables collect in the condenser and raise condensing pressure above the saturation value for the leaving water temperature, which shows up as a condenser approach greater than design. The purge unit will also run longer than normal.

  112. Question 112Type III - Low-Pressure Appliances

    Which problem is caused by moisture inside a low-pressure chiller?

    1. reduced purge operation
    2. low discharge temperature
    3. higher evaporator capacity
    4. acid and sludge in the oil Correct answer.

    Explanation

    Water reacts with refrigerant and oil to form acids and sludge, and it can freeze at the metering device and block flow. Moisture is removed with filter driers and monitored with a moisture indicator.

  113. Question 113Type III - Low-Pressure Appliances

    What must never be done to the rupture disc on a low-pressure chiller?

    1. cap it, plug it, or valve it off Correct answer.
    2. replace it after it bursts
    3. route its discharge outdoors
    4. tag it with its relief setting

    Explanation

    The rupture disc is the machine's only overpressure protection, and isolating it leaves the low-pressure shell with no relief path. The disc must vent freely, normally to a safe outdoor location.

  114. Question 114Type III - Low-Pressure Appliances

    During recovery from a low-pressure chiller, the fastest safe way to keep refrigerant boiling off is to:

    1. circulate warm water through the evaporator tubes Correct answer.
    2. run the chiller compressor to push the charge out
    3. add nitrogen until the shell reaches 50 psig
    4. pull a deeper vacuum with the recovery machine

    Explanation

    Adding heat through the chiller water raises the refrigerant's vapor pressure so the recovery unit can keep removing vapor. Any applied pressure, such as nitrogen, must stay well below the rupture disc setting.

  115. Question 115Type III - Low-Pressure Appliances

    After evacuating a low-pressure chiller, a standing vacuum test shows the pressure rising steadily. This indicates that:

    1. the gauge is reading in psig
    2. the system is overcharged
    3. the vacuum pump is worn out
    4. there is a leak or moisture remains in the system Correct answer.

    Explanation

    In a tight, dry system the vacuum holds. A steady rise means vapor is being generated inside, either by air entering through a leak or by moisture boiling off, so the leak must be found or dehydration continued.

  116. Question 116Type III - Low-Pressure Appliances

    R-123, the common replacement for R-11 in centrifugal chillers, belongs to which ASHRAE safety group?

    1. A2L
    2. A1
    3. B1 Correct answer.
    4. A3

    Explanation

    R-123 is classified B1, meaning higher toxicity with no flame propagation. That rating is why machine rooms using it need leak monitoring and good ventilation, and why its exposure limit is tighter than that of R-11.

  117. Question 117Type III - Low-Pressure Appliances

    R-123 is which class of refrigerant?

    1. HFO
    2. HFC
    3. HCFC Correct answer.
    4. CFC

    Explanation

    R-123 is an HCFC, with an ozone depletion potential far lower than the CFC it replaced. Because it is an HCFC, its production and import have been phased out, although recovered material may still be used for service.

  118. Question 118Type III - Low-Pressure Appliances

    When a low-pressure chiller is taken out of service and dismantled, the refrigerant must be:

    1. burned off at the site
    2. recovered Correct answer.
    3. discharged to the roof
    4. vented slowly through the purge unit

    Explanation

    Section 608 prohibits knowingly venting refrigerant to the atmosphere, so the charge must be recovered before an appliance is dismantled or disposed of. The rule applies whether the machine is being repaired or scrapped.

  119. Question 119Type III - Low-Pressure Appliances

    Which approach is acceptable for locating a leak on a low-pressure chiller?

    1. listen for a hissing sound while it runs in a vacuum
    2. spray soap bubbles on the shell while it is under vacuum
    3. pressurize the shell with nitrogen and use an electronic detector or bubbles Correct answer.
    4. watch the purge unit for activity

    Explanation

    Because the shell sits below atmospheric pressure, air flows in and refrigerant does not escape, so a leak detector has nothing to sense. The machine must be isolated, evacuated, and pressurized with nitrogen below the rupture disc setting to make the leak detectable.

  120. Question 120Type III - Low-Pressure Appliances

    At sea level, a vacuum gauge on a chiller reads 25 in. Hg vacuum. The absolute pressure inside the shell is approximately:

    1. 0 psia
    2. 29.9 psia
    3. 4.9 in. Hg absolute Correct answer.
    4. 25 in. Hg absolute

    Explanation

    A vacuum gauge reads how far the pressure is below atmospheric, which is about 29.9 in. Hg at sea level. Subtracting the 25 in. Hg reading leaves roughly 4.9 in. Hg absolute, far from a perfect vacuum.

  121. Question 121Type III - Low-Pressure Appliances

    When pressure-testing an evacuated low-pressure chiller with nitrogen, the test pressure must not exceed:

    1. 150 psig
    2. the rupture disc setting, typically about 15 psig Correct answer.
    3. 25 in. Hg
    4. 60 psig

    Explanation

    The low side of a low-pressure chiller is designed for only a few pounds of positive pressure, and the rupture disc usually bursts near 15 psig. Test pressure must stay below that rating to protect the disc and the shell.

  122. Question 122Type III - Low-Pressure Appliances

    A water-cooled chiller has just had a leaking condenser tube repaired. Which follow-up step is required?

    1. no action, because the tube leak is fixed
    2. increase the purge rate permanently
    3. add refrigerant to dilute the water that entered
    4. test oil for moisture and acidity, then change driers as needed Correct answer.

    Explanation

    A tube leak lets water into the refrigerant circuit, where it forms acids and sludge and can freeze at the metering device. After the repair the oil and refrigerant must be tested, driers replaced, and the system dehydrated before it goes back in service.

  123. Question 123Type III - Low-Pressure Appliances

    Recovered refrigerant that will be sold to a different owner must be:

    1. recycled on site and labeled as new product
    2. used only in the appliance it was removed from
    3. vented and replaced with virgin refrigerant
    4. reclaimed to ARI 700 purity by an EPA-certified reclaimer Correct answer.

    Explanation

    Under Section 608, refrigerant transferred to a new owner must be reclaimed, meaning it is reprocessed to ARI 700 purity by an EPA-certified reclaimer and labeled accordingly. Recycled refrigerant may only go back into the same appliance or the same owner's equipment.

  124. Question 124Type III - Low-Pressure Appliances

    In a hermetic centrifugal chiller, the refrigerant also serves to:

    1. absorb moisture in the evaporator
    2. seal the shaft packing
    3. cool the compressor motor Correct answer.
    4. lubricate the compressor bearings

    Explanation

    In a hermetic machine the motor sits inside the refrigerant circuit, and refrigerant is circulated to carry away motor heat. Lubrication is the job of the oil, not the refrigerant.

  125. Question 125Type III - Low-Pressure Appliances

    Under EPA regulations, a low-pressure appliance is one that uses a refrigerant whose saturation pressure at 104 degrees F does not exceed:

    1. 15 psig Correct answer.
    2. 50 psig
    3. 25 psig
    4. 150 psig

    Explanation

    The regulatory dividing line is a saturation pressure of 15 psig at 104 degrees F; anything at or below that is a low-pressure appliance. Chillers using R-11, R-113, or R-123 fall into this category and are covered by Type III certification.

  126. Question 126Type III - Low-Pressure Appliances

    Which of these refrigerants is a low-pressure refrigerant commonly used in centrifugal chillers?

    1. R-410A
    2. R-22
    3. R-123 Correct answer.
    4. R-134a

    Explanation

    R-123 is an HCFC with a low saturation pressure and is the usual replacement for R-11 in centrifugal chillers. Its low-pressure characteristics mean the evaporator shell normally sits in a vacuum.

  127. Question 127Type III - Low-Pressure Appliances

    Which EPA Section 608 certification type is required to service a chiller charged with R-123?

    1. Type III Correct answer.
    2. Type II
    3. Type IV
    4. Type I

    Explanation

    Type III certification covers the maintenance, service, repair, and disposal of low-pressure appliances. Type IV is not one of the certification categories offered under Section 608.

  128. Question 128Type III - Low-Pressure Appliances

    What is the primary function of a purge unit on a low-pressure centrifugal chiller?

    1. Lubricate the compressor bearings
    2. Maintain the refrigerant charge
    3. Control the chilled water flow
    4. Remove non-condensables and moisture Correct answer.

    Explanation

    Because the shell operates in a vacuum, air and moisture can be drawn in and collect in the condenser. The purge unit separates and expels these non-condensables so capacity and efficiency are not lost.

  129. Question 129Type III - Low-Pressure Appliances

    Under Section 608, refrigerant removed from a low-pressure appliance must be:

    1. Recovered, recycled, or reclaimed Correct answer.
    2. Vented if the charge is under 5 lb
    3. Vented if the refrigerant is a CFC
    4. Released slowly to the outdoors

    Explanation

    Knowing venting of ozone-depleting refrigerants is prohibited, so the charge must be recovered and then recycled, reclaimed, or destroyed. The size of the charge and the refrigerant class do not change this requirement.

  130. Question 130Type III - Low-Pressure Appliances

    Liquid R-123 can cause frostbite or chemical burns on contact, so a technician handling it should wear:

    1. A paper respirator and latex gloves
    2. Leather gloves and a hard hat
    3. Goggles and refrigerant-rated gloves Correct answer.
    4. A dust mask and cotton gloves

    Explanation

    Liquid refrigerant at its boiling point flashes off and freezes skin, so eye protection and gloves rated for refrigerant contact are required. Ordinary work gloves or latex do not resist refrigerant permeation.

  131. Question 131Type III - Low-Pressure Appliances

    Which instrument is used to measure the deep vacuum required when evacuating a low-pressure chiller?

    1. A psig pressure transducer
    2. A mercury manometer
    3. An electronic micron gauge Correct answer.
    4. A compound gauge

    Explanation

    A micron gauge reads in the very low absolute pressure range needed to confirm dehydration of a chiller. Standard gauges lack the resolution to show whether the required deep vacuum has actually been reached.

  132. Question 132Type III - Low-Pressure Appliances

    Recovery cylinders used with low-pressure refrigerants must be:

    1. Propane cylinders with an adapter fitting
    2. Unmarked steel drums fitted with a hand valve
    3. DOT-approved cylinders marked for that refrigerant Correct answer.
    4. Disposable one-way cylinders

    Explanation

    Refrigerant may only be stored in cylinders approved for the refrigerant and marked accordingly, so the contents are never confused. Mixing refrigerants in an unmarked or mismatched cylinder makes the charge unusable and unsafe.

  133. Question 133Type III - Low-Pressure Appliances

    A purge unit on a low-pressure chiller that normally runs a few minutes per day begins running almost continuously. The most likely cause is:

    1. Normal operation in humid weather
    2. Air leaking into the machine Correct answer.
    3. An overcharged purge unit
    4. Low chilled water temperature

    Explanation

    Purge run time is a direct indicator of how much non-condensable gas is entering the shell. A sudden increase in purge frequency usually means the vacuum shell has developed an air leak that must be located and repaired.

  134. Question 134Type III - Low-Pressure Appliances

    A rupture disc on a low-pressure chiller is typically designed to burst at approximately:

    1. 1 psig
    2. 150 psig
    3. 75 psig
    4. 15 psig Correct answer.

    Explanation

    The rupture disc is sized to protect a shell that is built for very low pressures, so it is set near 15 psig. Pressurizing the shell above that setting will rupture the disc and release the charge.

  135. Question 135Type III - Low-Pressure Appliances

    The relief piping connected to a chiller's rupture disc must be directed to:

    1. The machine room return air duct
    2. A safe outdoor discharge point Correct answer.
    3. The evaporator shell
    4. The condenser water drain line

    Explanation

    Refrigerant released by a relief device must be carried to a location where it will disperse without endangering people. Routing it indoors or into a water drain would expose occupants or contaminate the water system.

  136. Question 136Type III - Low-Pressure Appliances

    Which gas must never be used to pressurize a refrigeration system for leak testing?

    1. Oxygen Correct answer.
    2. Helium
    3. Dry nitrogen
    4. Argon

    Explanation

    Oxygen under pressure combines with compressor oil and can ignite or explode. Dry nitrogen is the standard pressurizing gas because it is inert and carries no moisture into the system.

  137. Question 137Type III - Low-Pressure Appliances

    A low-pressure chiller is operating with an unusually low refrigerant charge. Which condition is most likely to result?

    1. The purge unit running less often
    2. Condenser water leaving too cold
    3. Chilled water freezing in the evaporator Correct answer.
    4. Suction pressure rising above design

    Explanation

    A short charge lowers evaporator pressure and temperature, and the saturated refrigerant can fall below the freezing point of the water in the tubes. The low-pressure safety cutout should be checked and the charge corrected.

  138. Question 138Type III - Low-Pressure Appliances

    After a chiller has been opened for repairs, which procedure is used to remove moisture from the system?

    1. Sweeping with compressed air
    2. Purging with refrigerant vapor
    3. Triple evacuation with nitrogen Correct answer.
    4. Flushing with tap water

    Explanation

    Breaking the vacuum with dry nitrogen and evacuating again several times progressively dilutes and carries out residual moisture. The process is repeated until the micron gauge holds at the target level.

  139. Question 139Type III - Low-Pressure Appliances

    Refrigerant that is cleaned at the job site with filter-driers and then returned to the same appliance is best described as:

    1. Recycled Correct answer.
    2. Vented
    3. Destroyed
    4. Reclaimed

    Explanation

    Recycling is the on-site cleaning of refrigerant for reuse in the same equipment or another appliance owned by the same owner. Reclaiming requires reprocessing at a facility to meet the new-product purity standard.

  140. Question 140Type III - Low-Pressure Appliances

    Why is a refrigerant vapor monitor often installed in a machine room housing an R-123 chiller?

    1. R-123 is toxic at low concentrations Correct answer.
    2. R-123 releases oxygen when heated
    3. R-123 is flammable at low concentrations
    4. R-123 is lighter than air and rises quickly

    Explanation

    R-123 has a very low occupational exposure limit, so small concentrations in a machine room can harm workers. A monitor sounds an alarm and starts ventilation before exposure becomes significant.

  141. Question 141Type III - Low-Pressure Appliances

    An appliance with a refrigerant charge of 50 pounds or more is found leaking above the allowable rate. The owner must:

    1. Repair the leak within 30 days Correct answer.
    2. Repair the leak within 1 year
    3. Repair the leak within 6 months
    4. Repair the leak at the next scheduled service

    Explanation

    Appliances at or above the 50-pound threshold must be repaired within 30 days of discovering a leak that exceeds the allowable rate. Verification that the repair succeeded is also required shortly afterward.

  142. Question 142Type III - Low-Pressure Appliances

    Which equipment is required to remove refrigerant from a low-pressure chiller?

    1. The chiller's own compressor
    2. Certified low-pressure recovery equipment Correct answer.
    3. A hand pump and a calibrated bucket
    4. A vacuum cleaner with a sealed motor

    Explanation

    Refrigerant must be transferred with recovery equipment certified for low-pressure appliances, which is built to pull and hold a deep vacuum. Improvised devices do not meet the certification standard and risk releasing refrigerant.

  143. Question 143Type III - Low-Pressure Appliances

    Compared with R-11, the ozone depletion potential of R-123 is:

    1. Much lower Correct answer.
    2. About the same
    3. Zero
    4. Much higher

    Explanation

    R-11 is a CFC with an ozone depletion potential near 1.0, while R-123 is an HCFC with an ODP of roughly 0.02. R-123 is therefore far less damaging to stratospheric ozone, although it is still a controlled substance.

  144. Question 144Type III - Low-Pressure Appliances

    When using a leak detector to find an R-123 leak in a machine room, the probe should be placed:

    1. Near the ceiling above the chiller
    2. At eye level near the controls
    3. Near the floor around the chiller Correct answer.
    4. At the return air grille only

    Explanation

    R-123 vapor is heavier than air, so leaking refrigerant settles at low points around the equipment. Sampling near the floor and in pits or low corners gives the fastest indication of a leak.

  145. Question 145Type III - Low-Pressure Appliances

    A vacuum gauge on a chiller at sea level reads 28 inches of mercury vacuum. The absolute pressure inside the shell is approximately:

    1. About 14.7 psia
    2. About 1 psia Correct answer.
    3. About 5 psia
    4. About 3 psia

    Explanation

    At sea level a perfect vacuum is about 29.92 inches of mercury, so a reading of 28 inches leaves roughly 1.9 inches of mercury absolute. Converting at about 0.49 psi per inch gives approximately 0.9 psia, or about 1 psia.

  146. Question 146Type III - Low-Pressure Appliances

    In a low-pressure chiller, the purge unit draws its sample from the condenser because non-condensables:

    1. Dissolve readily in liquid refrigerant
    2. Form only inside the evaporator
    3. Are heavier than liquid refrigerant
    4. Collect where they cannot condense Correct answer.

    Explanation

    Air and other non-condensable gases cannot change to liquid at condenser conditions, so they blanket the condenser tubes and concentrate there. Sampling that area lets the purge unit remove them with the least refrigerant loss.

  147. Question 147Type III - Low-Pressure Appliances

    An open-flame leak detector used on a refrigerant that contains chlorine can:

    1. Produce toxic breakdown products Correct answer.
    2. Raise the system pressure
    3. Damage the ozone layer directly
    4. Freeze the leak point

    Explanation

    Refrigerants containing chlorine break down in a flame into hazardous gases, so open-flame detectors create a health hazard for the technician. Electronic detectors and soap solutions are the safer choices.

  148. Question 148Type III - Low-Pressure Appliances

    ASHRAE safety group B1, which applies to R-123, indicates:

    1. Higher toxicity, high flammability
    2. Lower toxicity, no flame propagation
    3. Higher toxicity, no flame propagation Correct answer.
    4. Lower toxicity, high flammability

    Explanation

    The letter in an ASHRAE safety group describes toxicity, with B indicating higher toxicity, and the number describes flammability, with 1 meaning no flame propagation. R-123 is therefore toxic but not flammable, which drives the ventilation and monitoring requirements.

  149. Question 149Type III - Low-Pressure Appliances

    Why is a pressure of 0 psig an inadequate endpoint when recovering refrigerant from a low-pressure chiller?

    1. A gauge cannot read 0 psig accurately
    2. The rule applies only to R-22 systems
    3. Recovery must always end at a positive pressure
    4. The chiller normally runs below atmospheric pressure Correct answer.

    Explanation

    A low-pressure chiller operates with its shell in a vacuum, so reaching 0 psig actually leaves the shell above its normal operating pressure with refrigerant still inside. Recovery must continue into a deep vacuum measured in inches of mercury or microns.

  150. Question 150Universal (Types I, II, and III)

    Which action is prohibited by Section 608 of the Clean Air Act when servicing stationary refrigeration equipment?

    1. Venting refrigerant to the atmosphere Correct answer.
    2. Recovering refrigerant into an approved cylinder
    3. Recycling refrigerant through a filter-drier assembly
    4. Recording the quantity of refrigerant recovered

    Explanation

    Section 608 prohibits knowingly venting ozone-depleting refrigerants and their substitutes to the atmosphere during maintenance, service, repair, or disposal. Refrigerant must instead be recovered with certified equipment.

  151. Question 151Universal (Types I, II, and III)

    Which of the following refrigerants has the highest ozone depletion potential?

    1. R-11 Correct answer.
    2. R-134a
    3. R-410A
    4. R-22

    Explanation

    Chlorofluorocarbons such as R-11 carry an ozone depletion potential near 1.0 because they contain chlorine and no hydrogen, so they persist long enough to reach the stratosphere. HCFCs such as R-22 are roughly a twentieth as destructive, and HFCs are zero.

  152. Question 152Universal (Types I, II, and III)

    Recovery cylinders are identified by which color scheme?

    1. White body with a red top
    2. Gray body with a yellow top Correct answer.
    3. Gray body with a green top
    4. Solid yellow body with a gray top

    Explanation

    The industry standard marks recovery cylinders with a gray body and a yellow top so they are not confused with virgin refrigerant cylinders. Cylinders used for recovery must also carry the required labeling and be DOT-approved.

  153. Question 153Universal (Types I, II, and III)

    Under EPA rules, a small appliance is one that is hermetically sealed, factory-charged, and holds a refrigerant charge of no more than:

    1. 5 pounds Correct answer.
    2. 2 pounds
    3. 50 pounds
    4. 15 pounds

    Explanation

    A small appliance is fully manufactured, charged, and hermetically sealed in a factory with 5 pounds or less of refrigerant. Such appliances fall under Type I certification and the small-appliance recovery rules.

  154. Question 154Universal (Types I, II, and III)

    Which of these refrigerants is a chlorofluorocarbon (CFC)?

    1. R-410A
    2. R-12 Correct answer.
    3. R-134a
    4. R-22

    Explanation

    CFCs contain chlorine, fluorine, and carbon but no hydrogen; R-12 fits that description. The absence of hydrogen is what makes CFCs so stable and so damaging to stratospheric ozone.

  155. Question 155Universal (Types I, II, and III)

    Section 608 of the Clean Air Act applies to which equipment?

    1. Aircraft cabin cooling systems
    2. Stationary refrigeration and AC equipment Correct answer.
    3. Residential refrigerators in transit
    4. Motor vehicle air conditioners

    Explanation

    Section 608 governs stationary refrigeration and air-conditioning equipment, including the recovery, recycling, and reclamation of refrigerant. Mobile air conditioners are regulated separately under Section 609.

  156. Question 156Universal (Types I, II, and III)

    Which EPA certification type is required to service a centrifugal chiller that uses R-123?

    1. Core only
    2. Type III Correct answer.
    3. Type I
    4. Type II

    Explanation

    R-123 is a low-pressure refrigerant, and low-pressure appliances fall under Type III certification. Type I covers small appliances and Type II covers high-pressure appliances.

  157. Question 157Universal (Types I, II, and III)

    Why must oxygen never be used to pressure-test a refrigeration system?

    1. It can explode when mixed with oil Correct answer.
    2. It forms toxic gas when it contacts copper
    3. It freezes the metering device on contact
    4. It alters the refrigerant boiling point

    Explanation

    Oxygen under pressure combined with refrigerant oil or other hydrocarbons can detonate violently. Dry nitrogen is the accepted test gas because it is inert and does not support combustion.

  158. Question 158Universal (Types I, II, and III)

    Before the sealed circuit of a small appliance is opened, the refrigerant must be evacuated to:

    1. 25 inches of mercury vacuum
    2. 0 psig
    3. 10 inches of mercury vacuum
    4. 4 inches of mercury vacuum Correct answer.

    Explanation

    The required evacuation level for small appliances is 4 inches of mercury vacuum, or recovery of 80 percent of the charge. Deeper vacuums apply to larger high-pressure and low-pressure appliances.

  159. Question 159Universal (Types I, II, and III)

    A technician is recovering refrigerant from a high-pressure appliance containing 250 pounds of R-410A. To what level must the appliance be evacuated?

    1. 4 inches of mercury vacuum
    2. 0 psig
    3. 10 inches of mercury vacuum
    4. 15 inches of mercury vacuum Correct answer.

    Explanation

    High-pressure appliances holding 200 pounds or more must be evacuated to 15 inches of mercury vacuum before the circuit is opened. Smaller high-pressure charges require 10 inches.

  160. Question 160Universal (Types I, II, and III)

    To what vacuum level must a low-pressure appliance be evacuated before service?

    1. 4 inches of mercury vacuum
    2. 15 inches of mercury vacuum
    3. 10 inches of mercury vacuum
    4. 25 inches of mercury vacuum Correct answer.

    Explanation

    Low-pressure appliances such as R-11 and R-123 chillers must be evacuated to 25 inches of mercury vacuum, the deepest of the required levels. Their low operating pressures make this level necessary and achievable.

  161. Question 161Universal (Types I, II, and III)

    A technician must recover refrigerant from a unit whose compressor will not run. Which equipment is required?

    1. A hand-operated vacuum pump alone
    2. A system-dependent recovery device
    3. A recovery cylinder chilled with dry ice
    4. A self-contained recovery machine Correct answer.

    Explanation

    System-dependent recovery equipment relies on the appliance's own compressor to move refrigerant, so it cannot be used when that compressor is inoperative. A self-contained recovery machine creates its own pressure difference and must be used instead.

  162. Question 162Universal (Types I, II, and III)

    A comfort-cooling appliance holds 60 pounds of R-410A and is found to be leaking at 12 percent of its charge per year. What does the rule require?

    1. The charge must be reduced below 50 pounds
    2. The leak must be repaired within 30 days Correct answer.
    3. The appliance must be retrofitted to a new refrigerant
    4. No action, since the leak is below 15 percent

    Explanation

    Comfort-cooling appliances with 50 pounds or more of charge have a leak-rate threshold of 10 percent per year. A 12 percent leak exceeds that threshold, so the leak must be repaired within 30 days of discovery.

  163. Question 163Universal (Types I, II, and III)

    A refrigerant cylinder must never be filled above what percentage of its capacity?

    1. 90 percent
    2. 80 percent Correct answer.
    3. 100 percent
    4. 95 percent

    Explanation

    Cylinders are limited to 80 percent of capacity by weight to leave room for liquid expansion as temperature rises. Overfilling can generate hydrostatic pressure sufficient to rupture the cylinder.

  164. Question 164Universal (Types I, II, and III)

    Refrigerant that has been recovered and is of unknown or mixed composition must be:

    1. Returned to the appliance without processing
    2. Blended with new refrigerant to restore its properties
    3. Vented slowly through a filter-drier
    4. Labeled and sent to an EPA-certified reclaimer Correct answer.

    Explanation

    Mixed or unidentified refrigerant cannot be restored to a known specification, so it must be kept in a labeled cylinder and sent to an EPA-certified reclaimer or destroyed. Refrigerants of different types must never be mixed in one cylinder.

  165. Question 165Universal (Types I, II, and III)

    What distinguishes reclamation from recycling of refrigerant?

    1. Recycling restores refrigerant to ARI-700 purity using chemical processing
    2. Reclamation restores purity verified by chemical analysis Correct answer.
    3. Recycling requires that refrigerant be shipped off site for destruction
    4. Reclamation may only be performed at the appliance location

    Explanation

    Reclamation is performed off site by an EPA-certified reclaimer that processes the refrigerant and verifies it meets ARI-700 purity through chemical analysis. Recycling is an on-site cleanup that removes oil, acid, and moisture but does not restore the refrigerant to a specification.

  166. Question 166Universal (Types I, II, and III)

    Which component removes air and other non-condensables that enter a low-pressure chiller?

    1. A liquid receiver
    2. A suction accumulator
    3. An economizer
    4. A purge unit Correct answer.

    Explanation

    Because a low-pressure chiller operates below atmospheric pressure, air and moisture leak inward rather than refrigerant leaking out. A purge unit collects and expels these non-condensables so head pressure and efficiency are not degraded.

  167. Question 167Universal (Types I, II, and III)

    When leak testing a low-pressure appliance with nitrogen, the pressure should not exceed:

    1. 10 psig Correct answer.
    2. 25 psig
    3. 50 psig
    4. 150 psig

    Explanation

    Low-pressure equipment is built for pressures near or below atmospheric and cannot safely withstand high test pressures. Testing above 10 psig risks rupturing the vessel or its relief device.

  168. Question 168Universal (Types I, II, and III)

    Which technique usually recovers refrigerant fastest from a system?

    1. Recovery with the system compressor running
    2. Vapor recovery from the suction line
    3. Recovery through the charging hose only
    4. Liquid recovery from the liquid line Correct answer.

    Explanation

    Pulling liquid refrigerant directly from the liquid line removes far more mass per unit of time than vapor recovery, because vapor must be boiled off and recondensed. Most recovery is therefore started in the liquid phase and finished in the vapor phase.

  169. Question 169Universal (Types I, II, and III)

    Under EPA regulations, refrigerant may be sold to:

    1. Any building owner with a maintenance staff
    2. Any person who signs a receipt
    3. Any HVAC student enrolled in a program
    4. Only certified Section 608 technicians Correct answer.

    Explanation

    Sale of ozone-depleting refrigerants, and now their HFC substitutes, is restricted to technicians certified under Section 608. A receipt or enrollment in a training program does not satisfy the certification requirement.

  170. Question 170Universal (Types I, II, and III)

    After repairing a leak on a 75-pound comfort-cooling appliance, when must the initial verification test be completed?

    1. Within 30 days of completing the repair Correct answer.
    2. Within 10 months of completing the repair
    3. Before any refrigerant is added back
    4. Within 24 hours of completing the repair

    Explanation

    The initial verification test must be completed within 30 days after the repair is finished, with the appliance charged and operating normally. A follow-up verification test is then due within 10 months of the initial verification.

  171. Question 171Universal (Types I, II, and III)

    A commercial refrigeration appliance with a 200-pound charge leaks at 25 percent per year. Which statement is correct?

    1. Repair is required only if the leak reaches 35 percent
    2. The appliance must be retired immediately
    3. The 20 percent threshold is exceeded; repair is required Correct answer.
    4. No repair is required because the threshold is 30 percent

    Explanation

    The leak-rate threshold for commercial refrigeration is 20 percent per year, so a 25 percent leak triggers the repair requirement. Comfort cooling uses 10 percent and industrial process refrigeration uses 30 percent.

  172. Question 172Universal (Types I, II, and III)

    As of January 1, 2020, what is the status of HCFC-22 production and import in the United States?

    1. Production and import are banned; recovered R-22 may be used Correct answer.
    2. Production and import are limited to 10 percent of the baseline
    3. Production continues at the 2015 level until 2030
    4. Only newly produced R-22 may be used for service

    Explanation

    The HCFC phaseout reached its final step on January 1, 2020, ending production and import of R-22 except for limited feedstock uses. Existing equipment may still be serviced with recovered or reclaimed R-22.

  173. Question 173Universal (Types I, II, and III)

    A system is evacuated to 500 microns and then isolated. The vacuum rises to 1,500 microns and holds steady. What does this most likely indicate?

    1. The system is properly dehydrated
    2. A leak or moisture remains in the system Correct answer.
    3. The vacuum gauge is out of calibration only
    4. The vacuum pump is too large for the system

    Explanation

    A tight, dry system holds well below 500 microns after isolation; a rise that stabilizes above the target indicates air entering through a leak or moisture boiling off inside. The standing vacuum test is used precisely to confirm tightness and dehydration.

  174. Question 174Universal (Types I, II, and III)

    When charging a system with a zeotropic refrigerant blend, the refrigerant must be:

    1. Warmed above 90 degrees Fahrenheit before charging
    2. Charged as a liquid to prevent fractionation Correct answer.
    3. Charged through the suction line only
    4. Charged as a vapor to prevent slugging the compressor

    Explanation

    The components of a zeotropic blend have different boiling points, so vapor charging allows them to separate and changes the mixture left in the cylinder. Charging as a liquid keeps the composition of the blend consistent.

  175. Question 175Universal (Types I, II, and III)

    Under EPA Section 608, a small appliance is defined as having a refrigerant charge of no more than:

    1. 15 pounds
    2. 25 pounds
    3. 5 pounds Correct answer.
    4. 10 pounds

    Explanation

    Type I small appliances are hermetically sealed, factory-charged, and contain 5 pounds or less of refrigerant. Charges above that limit fall under other appliance categories.

  176. Question 176Universal (Types I, II, and III)

    Which of the following refrigerants is classified as a chlorofluorocarbon (CFC)?

    1. R-22
    2. R-134a
    3. R-12 Correct answer.
    4. R-410A

    Explanation

    CFCs contain chlorine, fluorine, and carbon, and R-12 is a common example. R-22 is an HCFC, while R-134a and R-410A are HFC-based refrigerants.

  177. Question 177Universal (Types I, II, and III)

    Which refrigerant has an ozone depletion potential (ODP) of zero?

    1. R-11
    2. R-134a Correct answer.
    3. R-123
    4. R-22

    Explanation

    HFCs such as R-134a contain no chlorine and therefore have zero ozone depletion potential. R-11 is a CFC, and R-22 and R-123 are HCFCs.

  178. Question 178Universal (Types I, II, and III)

    Dry nitrogen used for pressure testing must be supplied through a:

    1. a vacuum pump
    2. a micron gauge
    3. a float switch
    4. a regulator Correct answer.

    Explanation

    Nitrogen cylinders are high-pressure vessels, so a pressure regulator is required to reduce and control the test pressure. The other devices do not control cylinder pressure.

  179. Question 179Universal (Types I, II, and III)

    HFC refrigerants such as R-410A are typically used with which type of lubricant?

    1. Alkylbenzene oil
    2. Silicone oil
    3. Mineral oil
    4. POE oil Correct answer.

    Explanation

    HFCs are not miscible with mineral oil, so polyolester (POE) oil is the standard lubricant. Mineral and alkylbenzene oils are used with CFCs and HCFCs.

  180. Question 180Universal (Types I, II, and III)

    To legally service stationary refrigeration equipment under Section 608, a technician must:

    1. complete an OSHA course
    2. pass an EPA exam Correct answer.
    3. hold a state license
    4. register with the fire department

    Explanation

    Section 608 requires technicians to be certified by passing an EPA-approved certification exam. Other licenses or courses do not satisfy the refrigerant-handling certification requirement.

  181. Question 181Universal (Types I, II, and III)

    When recovering refrigerant from a small appliance with a working compressor, the technician must recover at least:

    1. 95% of the charge
    2. 65% of the charge
    3. 80% of the charge Correct answer.
    4. 50% of the charge

    Explanation

    For small appliances with an operating compressor, recovery must reach 80% of the charge. A higher percentage is required when the compressor is not running.

  182. Question 182Universal (Types I, II, and III)

    Records of refrigerant purchases, recovery, and leak repairs must be kept for:

    1. 6 months
    2. 3 years Correct answer.
    3. 1 year
    4. 2 years

    Explanation

    EPA regulations require refrigerant service records to be retained for at least three years. Shorter retention periods do not meet the recordkeeping requirement.

  183. Question 183Universal (Types I, II, and III)

    For a comfort-cooling appliance containing 50 pounds or more of refrigerant, leak repair is required when the annual leak rate exceeds:

    1. 40 percent
    2. 20 percent
    3. 30 percent
    4. 10 percent Correct answer.

    Explanation

    Comfort-cooling appliances have a 10% annual leak-rate threshold. Commercial refrigeration uses 20% and industrial process refrigeration uses 30%.

  184. Question 184Universal (Types I, II, and III)

    For industrial process refrigeration, the annual leak rate that triggers mandatory repair is:

    1. 10 percent
    2. 50 percent
    3. 20 percent
    4. 30 percent Correct answer.

    Explanation

    Industrial process equipment has a 30% annual leak-rate threshold. Comfort cooling is 10% and commercial refrigeration is 20%.

  185. Question 185Universal (Types I, II, and III)

    Once a leaking appliance is found to exceed its leak-rate threshold, the repair must generally be completed within:

    1. 7 days
    2. 90 days
    3. 14 days
    4. 30 days Correct answer.

    Explanation

    The owner must repair the leak within 30 days of discovery. A longer period applies only when a retrofit or retirement plan is chosen.

  186. Question 186Universal (Types I, II, and III)

    If a leaking appliance cannot be repaired, the owner may instead retrofit or retire it within:

    1. 60 days
    2. 90 days
    3. 120 days Correct answer.
    4. 30 days

    Explanation

    The regulations allow 120 days to retrofit or retire an appliance when repair is not feasible. Thirty days is the deadline for a normal repair.

  187. Question 187Universal (Types I, II, and III)

    After a leak repair is completed on a commercial refrigeration appliance, the follow-up verification test must be performed within:

    1. 30 days Correct answer.
    2. 120 days
    3. 60 days
    4. 10 days

    Explanation

    The follow-up verification test is due within 30 days after the repair is completed. It confirms that the repair reduced the leak below the applicable threshold.

  188. Question 188Universal (Types I, II, and III)

    Service tools used on R-410A systems must be rated for:

    1. higher pressure than R-22 tools Correct answer.
    2. lower pressure than R-22 tools
    3. R-12 pressures only
    4. vacuum only

    Explanation

    R-410A operates at substantially higher pressures than R-22, so gauges, hoses, and recovery equipment must be rated for it. Standard R-22 tools may fail or burst.

  189. Question 189Universal (Types I, II, and III)

    Refrigerant cylinders should be stored:

    1. on their sides in direct sunlight
    2. upright and secured Correct answer.
    3. in a closed vehicle
    4. near an open flame

    Explanation

    Cylinders should be stored upright, secured, and away from heat sources. Heat raises internal pressure and can cause a cylinder to rupture.

  190. Question 190Universal (Types I, II, and III)

    A micron gauge is used to:

    1. detect refrigerant leaks
    2. measure deep vacuum Correct answer.
    3. measure refrigerant weight
    4. measure outdoor temperature

    Explanation

    A micron gauge measures absolute pressure in the deep-vacuum range during evacuation. A standard compound gauge is not sensitive enough for this purpose.

  191. Question 191Universal (Types I, II, and III)

    During triple evacuation, dry nitrogen is used to:

    1. flush refrigerant through
    2. break the vacuum Correct answer.
    3. pressurize the recovery cylinder
    4. clean the vacuum pump oil

    Explanation

    Nitrogen is introduced to bring the system back to positive pressure between evacuation cycles, helping to sweep out moisture and air. It is not used as a refrigerant flush.

  192. Question 192Universal (Types I, II, and III)

    A suction-line filter drier should be replaced after:

    1. each refrigerant top-off
    2. a compressor burnout Correct answer.
    3. every routine filter change
    4. a thermostat adjustment

    Explanation

    Burnouts generate acid and debris that can clog the drier, so it must be replaced. Routine top-offs and control adjustments do not require drier replacement.

  193. Question 193Universal (Types I, II, and III)

    Liquid refrigerant contacting exposed skin can cause:

    1. frostbite Correct answer.
    2. a harmless tingling sensation
    3. heating of the skin
    4. a chemical burn from oil

    Explanation

    Refrigerant boils at a very low temperature and can freeze tissue on contact. Appropriate gloves and eye protection are required.

  194. Question 194Universal (Types I, II, and III)

    Venting HFC refrigerants such as R-134a during service is:

    1. allowed during system evacuation
    2. allowed for small appliances only
    3. prohibited under Section 608 Correct answer.
    4. allowed if the charge is under 5 pounds

    Explanation

    Section 608 prohibits knowingly venting ozone-depleting refrigerants and their substitutes, including HFCs. Refrigerant must be recovered instead.

  195. Question 195Universal (Types I, II, and III)

    A low-pressure chiller is being evacuated. Pulling the pressure below 25 mm Hg absolute may cause:

    1. the purge unit overfills
    2. the compressor overheats
    3. the refrigerant ignites
    4. water in tubes freezes Correct answer.

    Explanation

    Low-pressure chillers use water in the evaporator tubes, and very deep vacuum can freeze that water and damage tubes. Recovery should stop at the required level.

  196. Question 196Universal (Types I, II, and III)

    When recovering refrigerant from a small appliance whose compressor does not run, the required recovery level is:

    1. 50% of the charge
    2. 70% of the charge
    3. 90% of the charge Correct answer.
    4. 80% of the charge

    Explanation

    With a non-operating compressor, recovery must reach 90% of the charge. The 80% level applies when the compressor is running.

  197. Question 197Universal (Types I, II, and III)

    Under the AIM Act, leak repair requirements for HFC appliances generally apply to systems containing at least:

    1. 5 pounds
    2. 200 pounds
    3. 50 pounds Correct answer.
    4. 25 pounds

    Explanation

    The HFC leak-repair provisions apply to appliances with a charge of 50 pounds or more. Smaller charges are not covered by that requirement.

  198. Question 198Universal (Types I, II, and III)

    When recovering refrigerant from a low-pressure chiller, a recommended first step is to:

    1. use a standard R-22 recovery machine
    2. self-pump to the condenser Correct answer.
    3. fill the chiller with water
    4. vent the refrigerant to the atmosphere

    Explanation

    Self-pumping uses the chiller's own compressor to move refrigerant to the condenser, where it can be recovered more efficiently. Venting refrigerant is prohibited.

  199. Question 199Universal (Types I, II, and III)

    A low-pressure chiller operates below atmospheric pressure, so a leak in the shell typically causes:

    1. air and moisture enter the system Correct answer.
    2. refrigerant escapes rapidly
    3. oxygen forms inside the compressor
    4. refrigerant changes into a CFC

    Explanation

    Because the chiller operates in a vacuum, any shell leak draws air and moisture inward. That is why purge units and leak testing are important.

EPA 608 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Small appliance definition
A hermetically sealed, factory-charged appliance containing 5 pounds or less of refrigerant, such as household refrigerators, freezers, room air conditioners, dehumidifiers, and vending machines.
Type I disposal recovery target
When disposing of a small appliance, recover 80 percent of the refrigerant if the compressor is not operating, or 90 percent if the compressor is operating.
System-dependent recovery equipment
Recovery equipment that relies on the appliance's own compressor, internal pressure, or an attached vacuum pump rather than its own compressor; permitted for small appliances.
Venting prohibition
Deliberately releasing refrigerant to the atmosphere is illegal for all appliances. Recovered refrigerant must be recycled, reclaimed to AHRI 700 purity, or destroyed.
Process stub
A short length of tubing on a sealed system used for evacuation and charging; it is pinch-clamped and brazed closed once service is complete.
Recycled versus reclaimed refrigerant
Recycled refrigerant is cleaned on site for reuse in the same owner's equipment; reclaimed refrigerant is reprocessed to AHRI 700 purity and may be resold.
Motor vehicle AC exclusion
Motor vehicle air conditioners are not Type I appliances; they are governed by Section 609 rules and require a separate technician certification.
Capillary tube
A fixed-restriction metering device made of small-diameter tubing, common on small appliances; it has no moving parts and cannot be adjusted.
High-pressure appliance definition
An appliance using a refrigerant that boils below 32 degrees Fahrenheit at atmospheric pressure, such as R-22, R-134a, R-410A, R-404A, or R-407C.
200-pound evacuation trigger
An appliance containing 200 pounds or more of refrigerant must be evacuated to 15 inches of mercury vacuum before being opened for service or disposal.
Ten inches mercury vacuum
The required evacuation level for high-pressure appliances under 200 pounds of charge when recovery equipment manufactured after November 15, 1993 is used.
Pre-1993 recovery equipment levels
Recovery machines built before November 15, 1993 need only pull 4 inches of mercury vacuum for CFC/HCFC systems and 0 psig for HFC-134a appliances.
Leak rate thresholds
For appliances holding 50 pounds or more, leaks above 15 percent per year in comfort cooling or 35 percent in commercial refrigeration or industrial process must be repaired within 30 days.
R-410A charging
R-410A is a near-azeotropic blend of R-32 and R-125 that must be charged as a liquid; it operates at pressures roughly 60 percent higher than R-22.
Nitrogen pressure testing
Use dry nitrogen with a pressure regulator for leak testing high-pressure systems; never use oxygen, compressed air, or an open flame.
Recovery cylinder fill limit
A recovery cylinder must never be filled beyond 80 percent of its capacity by weight, because warming liquid refrigerant risks hydrostatic rupture of the cylinder.
Three-year record retention
Technicians and equipment owners must keep records of refrigerant purchases, recovery, recycling, and disposal for at least three years.
Low-pressure appliance definition
An appliance using a refrigerant with a boiling point at or above 32 degrees Fahrenheit at atmospheric pressure, typically R-11, R-113, or R-123 in centrifugal chillers.
25 millimeters mercury absolute
Low-pressure appliances must be evacuated to 25 millimeters of mercury absolute, roughly 29.6 inches of mercury vacuum, before opening or disposal.
Chiller compressor prohibition
The compressor of a low-pressure chiller must never be used to evacuate or recover refrigerant; a certified recovery unit is required instead.
Purge unit
Equipment that removes air and other noncondensables that leak into a low-pressure chiller, which operates below atmospheric pressure during normal running.
Rupture disc
A pressure relief device fitted to low-pressure chiller shells, typically designed to burst near 15 psig to protect the vessel from overpressure.
R-123 ozone depletion potential
R-123 is an HCFC with an ozone depletion potential of about 0.02, used to replace CFC R-11, which has an ozone depletion potential of 1.0.
R-11 boiling point
R-11 boils at about 75 degrees Fahrenheit at atmospheric pressure, so it sits at a vacuum inside the chiller and reads below zero on standard gauges.
Standing vacuum test
After evacuation, the system is isolated and the vacuum observed; a rising pressure indicates a leak or moisture still boiling off.
Universal certification
A Universal certification covers Type I, Type II, and Type III appliances, allowing the technician to service any charge size or pressure class.
De minimis release
A very small quantity of refrigerant released while connecting or disconnecting hoses during a good-faith repair is not treated as illegal venting.
Refrigerant decomposition products
Refrigerant exposed to flame or a hot surface breaks down into hydrogen fluoride, hydrogen chloride, and phosgene, so the area must be ventilated and vapors not inhaled.
AHRI 700
The standard that sets purity requirements for reclaimed refrigerant, including limits on moisture, acidity, high-boiling residues, and noncondensable gases.
ODP and GWP
Ozone depletion potential compares a refrigerant's ozone damage with CFC-11, set at 1.0; global warming potential compares heat trapping with carbon dioxide, also set at 1.0.
Liquid refrigerant frostbite
Liquid refrigerant boiling on skin causes frostbite and can freeze an eye on contact; wear gloves and goggles and flush exposed skin with lukewarm water.
Mixed refrigerant cylinder
Different refrigerants must never be mixed in one recovery cylinder; a mixed cylinder cannot be reclaimed and generally has to be destroyed.

EPA 608 study guide

Type I - Small Appliances

What this domain covers

Type I is the small-appliance category: hermetically sealed, factory-charged equipment holding 5 lb of refrigerant or less. Typical examples are household refrigerators and freezers, window and portable air conditioners, dehumidifiers, water coolers, vending machines, and small ice machines. These units have no service valves, so access is normally made through a process tube with a locking-type line-piercing valve - and the charge must be recovered before you pierce anything.

Rules you must be able to state

  • No venting, ever. Recovery is required even for a few ounces. A vacuum pump may never be used to dump refrigerant, and service venting is not a permitted exception.
  • Recovery target: 80% of the charge, whether or not the compressor is running. This flat 80% is the Type I number; the 90%/80% split and vacuum-level targets belong to other appliance classes.
  • System-dependent versus self-contained recovery. Passive (system-dependent) equipment relies on the appliance's own compressor and heat, so it cannot pull a deep vacuum; on a non-operating system it must be paired with a vacuum pump.
  • Recovery cylinders must be DOT-approved, never filled above 80% of capacity by weight, and never heated with a flame or torch.
  • Charging is by weight, using the data-plate charge as your reference.

Traps that show up in questions

  • The two different 80% values: 80% of the charge for recovery efficiency versus 80% of cylinder capacity for fill limit. Distractors swap them.
  • Small appliance is not motor-vehicle air conditioning; a Type I certificate does not authorize MVAC work.
  • Cheap self-piercing (non-locking) valves leak after the tool is removed. Use locking access valves and cap them.

Rule of thumb

A 4 lb charge means recovering at least 3.2 lb (80%) before opening the system, and the receiving cylinder must still be at or below 80% full by weight.

Type II - High-Pressure Appliances

What this domain covers

Type II covers high-pressure equipment that is not a small appliance or a low-pressure chiller: residential split systems, packaged and rooftop units, and high-pressure chillers. The refrigerants are the familiar ones - R-22, R-410A, R-407C, R-134a, R-12, R-500, R-502 - all of which boil well below ambient at atmospheric pressure, so a leak pushes refrigerant out rather than pulling air in.

Rules you must be able to state

  • Recovery targets depend on size and age. For an appliance manufactured before November 15, 1993 with less than 200 lb of charge, recover 90% when the compressor is operating and 80% when it is not. Larger appliances and appliances built after that date must be evacuated to a 10 in. Hg vacuum with the compressor running.
  • Recovery equipment must be certified to the AHRI 740 standard and rated for the refrigerant being handled.
  • Never mix refrigerants in a recovery cylinder. A mixed cylinder cannot be reclaimed and is treated as hazardous waste.
  • Blends (400-series) are zeotropic and must be charged as a liquid - into the liquid line or through a throttling device - so the components do not fractionate.
  • Pressure testing uses dry nitrogen only. Oxygen or compressed air plus oil can detonate.

Traps that show up in questions

  • Quoting the low-pressure vacuum target (25 mm Hg absolute) for a high-pressure job, or the reverse.
  • Using R-22 manifold gauges and hoses on R-410A, which runs roughly 50–70% higher pressure and needs its own equipment.
  • Vapor-charging a blend, or heating a cylinder with a torch to speed the transfer.

Rule of thumb

When the data plate and the recovery table disagree about how far to pull down, match the appliance's manufacture date and charge size first, then apply the 90%/80% or 10 in. Hg figure.

Type III - Low-Pressure Appliances

What this domain covers

Type III covers low-pressure appliances, almost always centrifugal chillers using R-11, R-113, or R-123. These refrigerants boil above ambient at atmospheric pressure, which means the machine normally runs in a vacuum: a leak pulls air and moisture in instead of pushing refrigerant out. That single fact drives nearly every rule in this domain.

Rules you must be able to state

  • Recovery target is 25 mm Hg absolute (roughly 1 in. Hg absolute, about 29 in. Hg of vacuum on a compound gauge). Standard high-pressure recovery machines generally cannot reach it, so equipment must be rated for low-pressure refrigerants.
  • Never use the chiller's own compressor to pull the system below 0 psig. Use a recovery machine.
  • Never open a low-pressure system to the atmosphere. If it must be opened, keep it at positive pressure with dry nitrogen; otherwise moisture-laden air rushes in, and water freezes at the metering device and forms acids in the oil.
  • Purge units remove air that leaks in. Excessive purging is a leak indicator, and purged refrigerant must be recovered, not vented.
  • Rupture disc protects the chiller from overpressure; if it bursts, the entire charge is lost and the release is reportable.
  • Leak testing is done by pressurizing with dry nitrogen - you cannot leak-check a machine that is sitting in a vacuum.

Traps that show up in questions

  • Confusing 25 mm Hg absolute with 25 in. Hg vacuum; they are wildly different targets.
  • Assuming a low-pressure chiller cannot leak because it is under vacuum - it leaks inward, which is why purge logs matter.
  • Charging liquid refrigerant into the compressor instead of following the manufacturer's charging point.

Rule of thumb

If the gauge is a compound gauge reading inches of vacuum, convert before comparing: 25 mm Hg absolute is about 0.98 in. Hg absolute, essentially a full vacuum, not a 25-inch pull.

Universal (Types I, II, and III)

What this domain covers

Universal certification is awarded after passing all three type exams, so the questions test your ability to attach the right rule to the right appliance class rather than to learn new subject matter. Expect mixed scenarios: a rooftop unit, a dehumidifier, and a chiller in the same question stem.

Rules you must be able to state

  • Never vent any refrigerant, including HFCs and their substitutes. Recovery, recycling, or reclaim is required in every service situation.
  • Know the three verbs. Recover means to remove refrigerant into an external container in any condition. Recycle means to clean it on site (oil separation, moisture and acid removal) for reuse in the same equipment. Reclaim means to reprocess it to new-product purity by an EPA-certified facility to AHRI 700 specifications.
  • Sales restriction: technicians must be certified to purchase ozone-depleting refrigerants, and since January 1, 2018 the same restriction covers HFCs.
  • Leak-rate thresholds apply to appliances holding 50 lb or more: 10% for comfort cooling, 20% for commercial refrigeration, 30% for industrial process refrigeration, 20% for other equipment, measured over 12 months. Exceeding the threshold requires repair within 30 days, followed by verification testing; records are kept three years. An appliance that leaks 125% of its charge in a year must be retrofitted or replaced.
  • Cylinder and site safety: DOT-approved cylinders, filled by weight to no more than 80% of capacity, never flame-heated, always secured upright.

Traps that show up in questions

  • Believing universal certification permits venting or exempts HFCs.
  • Mixing evacuation targets: 80% charge for small appliances, 90%/80% or 10 in. Hg for high-pressure, 25 mm Hg absolute for low-pressure.
  • Treating recycled refrigerant as if it were reclaimed; only reclaimed refrigerant may be sold or used in a different owner's equipment.

Rule of thumb

Before answering, name the appliance class out loud - that single identification usually eliminates three of the four answer choices.

EPA 608 cheat sheet

Quick reference

Type I - Small Appliances

  • Type I appliance: hermetically sealed, factory-charged, containing 5 lb (2.3 kg) or less of refrigerant - household refrigerators, freezers, room air conditioners, dehumidifiers, vending machines, drinking water coolers.

  • Motor vehicle air conditioners are not Type I appliances; they fall under Section 609 rules and separate certification.

  • Disposal recovery target for a small appliance: 80% of the charge if the compressor is not operating, 90% if the compressor is operating.

  • No specific vacuum level is mandated for Type I recovery, but the recovery equipment itself still must be EPA-certified.

  • System-dependent (passive) recovery equipment is permitted on Type I appliances and may rely on the appliance compressor, internal system pressure, or a vacuum pump attached to the system.

  • Recovered small-appliance refrigerant must be recycled, reclaimed to AHRI 700 purity, or destroyed; deliberate venting to the atmosphere is prohibited.

  • Small sealed systems commonly use a capillary tube (fixed restriction) and have no service valves; access is gained through a piercing valve or process stub that must be sealed afterward.

  • Recovery cylinders must be DOT-approved, labeled for the refrigerant they contain, and filled to no more than 80% of capacity by weight.

Quick reference

Type II - High-Pressure Appliances

  • Type II appliance: uses a refrigerant with a boiling point below 32°F at atmospheric pressure - R-22, R-134a, R-410A, R-404A, R-407C, R-502.

  • Evacuation level for appliances under 200 lb of charge: 10 in Hg vacuum with recovery equipment built after November 15, 1993; 4 in Hg for CFC/HCFC or 0 psig for HFC-134a/PFC with older equipment.

  • Appliances containing 200 lb or more of refrigerant must be evacuated to 15 in Hg vacuum before opening.

  • Very-high-pressure refrigerants (R-13, R-23, R-503): evacuate to 0 psig with pre-1993 recovery equipment and to 10 in Hg vacuum with post-1993 equipment.

  • Leak repair rule for appliances of 50 lb or more: repair within 30 days when the annual leak rate exceeds 15% (comfort cooling) or 35% (commercial refrigeration or industrial process).

  • An initial verification test is required within 30 days of completing a leak repair on a 50 lb or larger appliance, followed by a follow-up verification test 30 days later.

  • R-410A is a near-azeotropic 50/50 blend of R-32 and R-125: charge it as a liquid, expect roughly 60% higher pressures than R-22, and use POE oil.

  • Never pressure-test with oxygen or compressed air; use dry nitrogen with a regulator. Recovery cylinders must not exceed 80% fill by weight.

  • Records of refrigerant purchased, recovered, recycled, and disposed of must be retained for at least three years.

Quick reference

Type III - Low-Pressure Appliances

  • Type III appliance: uses a refrigerant whose boiling point is at or above 32°F at atmospheric pressure - R-11, R-113, R-123 - typically centrifugal chillers.

  • Low-pressure appliances must be evacuated to 25 mm of mercury absolute (about 29.6 in Hg vacuum) before being opened or disposed of.

  • Never use the appliance's own compressor to evacuate or recover refrigerant; a certified recovery unit is required.

  • Because the machine operates below atmospheric pressure, air and moisture leak inward; a high-efficiency purge unit removes noncondensables.

  • Never pressurize a low-pressure chiller with air; use dry nitrogen through a regulator. The shell carries a rupture disc that typically bursts near 15 psig.

  • R-11 (CFC, ODP 1.0) boils at about 75°F at atmospheric pressure; R-123 (HCFC, ODP about 0.02) is its low-pressure replacement.

  • Recover liquid refrigerant first, then vapor; confirm dryness with a standing (decay) vacuum test read on a micron gauge.

  • Moisture inside a chiller forms acids and sludge; oil testing and moisture indicators are the standard detection methods.

Quick reference

Universal (Types I, II, and III)

  • Universal certification covers Type I, Type II, and Type III; a technician certified in only one type may not service another type's appliances.

  • The venting prohibition applies to ozone-depleting refrigerants and their HFC substitutes; only de minimis releases during good-faith service are permitted.

  • Refrigerant contacting flame or hot metal decomposes into hydrogen fluoride, hydrogen chloride, and phosgene - ventilate the area and avoid breathing the products.

  • Reclaimed refrigerant must meet AHRI 700 purity; recycled refrigerant is cleaned on site and reused in the same owner's equipment.

  • CFCs carry the highest ODP (R-11 = 1.0), HCFCs far less (R-123 about 0.02), and HFCs zero ODP but high GWP.

  • Never mix different refrigerants in one recovery cylinder; a mixed cylinder cannot be reclaimed and generally must be destroyed.

  • Recovery and recycling equipment must be EPA-certified and used only for the appliance type it is certified for; certification records must be kept.

  • Liquid refrigerant causes frostbite and eye damage; wear gloves and goggles and flush exposed skin with lukewarm, not hot, water.

EPA 608 key terms

Section 608

The part of the Clean Air Act that regulates refrigerant handling and requires certification for technicians who service, repair, or dispose of appliances containing regulated refrigerants.

Related: Venting, Recovery
Ozone Depletion Potential (ODP)

A number comparing how strongly a substance destroys stratospheric ozone relative to CFC-11, which is set at 1.0. Higher values mean greater ozone damage.

Related: CFC, HCFC
Global Warming Potential (GWP)

A number comparing how much heat a greenhouse gas traps over a chosen period relative to carbon dioxide, which is set at 1. Higher values mean greater warming impact.

Related: HFC
Recovery

Removing refrigerant from an appliance and storing it in an external container without necessarily testing or processing it. Recovery is required before opening a system or disposing of equipment.

Related: Recycling, Reclaiming, Recovery cylinder
Recycling

Cleaning recovered refrigerant for reuse by removing oil, moisture, and other contaminants, usually with a filter-drier. Recycling does not restore refrigerant to new-product purity standards.

Related: Recovery, Reclaiming
Reclaiming

Reprocessing refrigerant to new-product purity specifications, verified by chemical analysis. Reclaimed refrigerant must meet AHRI Standard 700 before it can be resold or used in another owner's equipment.

Related: Recovery, Recycling
Evacuation

Removing air, moisture, and non-condensables from a system with a vacuum pump until a deep vacuum is reached, typically measured in microns. Proper evacuation prevents acid formation and ice blockage.

Related: Micron, Vacuum pump
Micron

A unit of length equal to one-millionth of a meter, used to measure deep vacuum. A vacuum of 500 microns or lower generally indicates adequate dehydration.

Related: Evacuation, Vacuum pump
Vacuum pump

A device that removes air and moisture from a refrigeration system to create a deep vacuum. Its oil must be changed regularly and the pump should be isolated with valves after shutdown.

Related: Evacuation, Micron
Manifold gauge set

A tool with gauges and valves used to measure system pressures and to connect service equipment such as vacuum pumps, recovery units, and charging cylinders to an appliance.

Related: Pressure-temperature chart
Non-condensables

Gases such as air or nitrogen that do not condense at normal system operating pressures, raising head pressure and reducing efficiency. They are removed by evacuation or purging.

Related: Evacuation, Purge unit
Refrigerant

A fluid used in a refrigeration cycle that absorbs heat by evaporating at low pressure and releases heat by condensing at high pressure. Each refrigerant has its own pressure-temperature relationship.

Related: Pressure-temperature chart, Saturation
CFC

A refrigerant made of chlorine, fluorine, and carbon, such as R-11 or R-12. CFCs have the highest ozone depletion potential and their production is banned.

Related: HCFC, Ozone Depletion Potential (ODP)
HCFC

A refrigerant containing hydrogen, chlorine, fluorine, and carbon, such as R-22. HCFCs deplete ozone less than CFCs but are being phased out.

Related: CFC, HFC
HFC

A refrigerant containing hydrogen, fluorine, and carbon but no chlorine, such as R-410A. HFCs do not damage stratospheric ozone but are potent greenhouse gases.

Related: Global Warming Potential (GWP), HCFC
Small appliance

Any appliance that is fully manufactured, charged, and hermetically sealed at the factory and contains five pounds or less of refrigerant, such as household refrigerators, freezers, and window air conditioners.

Related: Hermetically sealed, Process tube
Hermetically sealed

A compressor or system enclosed in a welded shell with no accessible shaft seal, so refrigerant cannot escape through a rotating seal. This design is common in small appliances.

Related: Small appliance, Access valve
Process tube

A short, sealed copper tube used at the factory to charge a hermetically sealed appliance. Technicians install access valves on it to recover refrigerant or service the sealed system.

Related: Access valve, Small appliance
Access valve

A service port installed on a sealed system or process tube that allows connection of gauges and recovery equipment without permanently opening the refrigerant circuit. It contains a spring-loaded core.

Related: Process tube
System-dependent recovery equipment

Recovery equipment that relies on the appliance's own compressor or on the pressure inside the appliance to move refrigerant into a recovery container. It cannot pull a deep vacuum by itself.

Related: Passive recovery, Small appliance
Passive recovery

A recovery method that uses only the appliance's internal pressure and gravity, with no mechanical pump, to transfer refrigerant into a container. It is often used for small appliances with a working compressor.

Related: System-dependent recovery equipment
Recovery cylinder

A refillable cylinder used to store recovered refrigerant. It must be DOT-approved, clearly labeled, never filled over 80 percent of its capacity, and have its valve protected.

Related: Recovery, 80 percent fill rule
80 percent fill rule

A safety rule requiring that a recovery cylinder be filled to no more than 80 percent of its volume with liquid refrigerant, leaving room for thermal expansion and preventing hydrostatic rupture.

Related: Recovery cylinder
Venting

Releasing refrigerant into the atmosphere. Venting is prohibited for most refrigerants and for appliances above certain charge sizes, so technicians must recover refrigerant instead.

Related: Recovery, Section 608
Leak detection

The process of finding refrigerant leaks using electronic detectors, ultrasonic devices, soap bubbles, or fluorescent dyes. Regular leak checks are required for appliances above a charge threshold.

Related: Venting
Nitrogen purge

Using dry nitrogen to displace air and moisture from tubing during brazing, preventing oxidation inside the system. Nitrogen must not be used to pressure-test a system beyond its rating.

Related: Evacuation
Superheat

The number of degrees a vapor refrigerant is above its saturation temperature at a given pressure. Measuring superheat helps verify proper charge and expansion valve operation.

Related: Subcooling, Saturation
Subcooling

The number of degrees a liquid refrigerant is below its saturation temperature at a given pressure. Measuring subcooling helps verify proper charge in systems with a thermostatic expansion valve.

Related: Superheat, Saturation
High-pressure appliance

A refrigeration appliance that uses a refrigerant with a boiling point above minus 50 degrees Fahrenheit at atmospheric pressure, such as R-22 or R-410A. It operates with positive pressure throughout.

Related: Low-pressure appliance, Superheat
Low-pressure appliance

A refrigeration appliance that operates with a saturated vapor pressure at or below 10 psig at normal operating temperatures, typically using R-11 or R-123 in centrifugal chillers.

Related: Centrifugal chiller, Purge unit
Centrifugal chiller

A large cooling machine that uses a rotating impeller to compress low-pressure refrigerant vapor, commonly found in large buildings. Many use R-123 and operate below atmospheric pressure.

Related: Low-pressure appliance, Purge unit
Purge unit

A device on low-pressure chillers that removes air and other non-condensables that leak into a system operating under vacuum. Efficient purging reduces refrigerant loss and energy waste.

Related: Low-pressure appliance, Non-condensables
Rupture disc

A one-time pressure relief device on low-pressure chillers that bursts at a set pressure to protect the vessel. It must be replaced after activation and checked for leaks.

Related: Low-pressure appliance, Purge unit
Charging cylinder

A graduated container used to measure and add liquid refrigerant to a system by weight. It must be equipped with a valve and never filled completely.

Related: Recovery cylinder
Pressure-temperature chart

A table showing the saturation pressure of a refrigerant at various temperatures. Technicians use it to determine charge, diagnose problems, and convert gauge readings.

Related: Saturation, Superheat, Subcooling
Saturation

The condition in which a refrigerant is at its boiling or condensing point for a given pressure, with both liquid and vapor present. At saturation, temperature and pressure are directly related.

Related: Superheat, Subcooling, Pressure-temperature chart

EPA 608 study plan

8 weeks · About 6 hours per week

Week 1

Universal (Types I, II, and III) & Type I - Small Appliances

  • Define ozone depletion potential (ODP) and global warming potential (GWP) and rank CFCs, HCFCs, HFCs, and HFOs by each metric

  • State the Clean Air Act venting prohibition and name the four permitted exceptions for knowingly releasing refrigerant

  • Identify the Section 608 certification categories and the sale, purchase, and recordkeeping rules that apply to refrigerant and recovery equipment

  • Distinguish recovery, recycling, and reclamation and name where each may legally occur

  • Recognize the definition and examples of a small appliance (hermetic, factory-sealed, 5 lb charge or less) and the recovery-evacuation level that applies to it

Your checkpoint

Closed-book 40-question Core + Type I quiz scored at 80% or higher, with every missed item logged alongside the correct rule.

Week 2

Type II - High-Pressure Appliances

  • Explain why high-pressure systems are recovered liquid first, then vapor, and describe the equipment setup for each phase

  • Apply recovery cylinder rules: the 80% fill limit, DOT marking, requalification intervals, and safe transfer procedures

  • Apply the evacuation level table by appliance type and charge size (0 psig, 10 in Hg vacuum, 25 mm Hg absolute)

  • Select the correct recovery machine, hoses, and cylinder for R-410A and other high-pressure blends

  • Describe the standing vacuum and vacuum-decay tests used to confirm a leak-free, moisture-free system

Your checkpoint

A one-page evacuation-level reference sheet reproduced from memory plus a 30-item evacuation-level drill scored at 90% or higher.

Week 3

Type II - High-Pressure Appliances & Type I - Small Appliances

  • Calculate leak rates and match them to the 15%, 20%, and 35% thresholds for industrial process refrigeration, commercial refrigeration, and comfort cooling, including the applicable repair and verification deadlines

  • Determine when an appliance must be retrofitted or retired instead of repaired

  • Choose between charging by weight, by subcooling, and by superheat for a given system and explain why the other methods are wrong

  • Describe the handling differences for R-410A and A2L refrigerants in pressure, lubricant, and leak-detection behavior

  • List the documentation required when refrigerant is added to or removed from an appliance

Your checkpoint

Type II section simulator (40 questions) scored at 85% or higher, supported by a five-scenario leak-rate calculation worksheet showing each step.

Week 4

Type III - Low-Pressure Appliances

  • Describe the operating characteristics of low-pressure centrifugal chillers, including evaporator pressures below atmospheric and the air/moisture ingress problem

  • Apply the 25 mm Hg absolute evacuation requirement to low-pressure appliances

  • Explain the purpose, operation, and efficiency testing of purge units

  • Describe rupture disc function, relief device settings, and the safe isolation of low-pressure vessels before service

  • Outline leak detection and charging methods for chillers, including charging refrigerant as a vapor and dehydrating a wet system

Your checkpoint

Type III section simulator scored at 85% or higher plus a text-described logic diagram linking chiller pressure, purge operation, and rupture-disc protection.

Week 5

Type III - Low-Pressure Appliances & Type II - High-Pressure Appliances

  • Compare low-pressure and high-pressure recovery and evacuation requirements side by side in a single table

  • Solve mixed scenarios in which the appliance type, charge size, and manufacture date all change the correct answer

  • Distinguish system-dependent from self-contained recovery equipment and identify when each is permitted

  • Explain the purity standards behind recycled versus reclaimed refrigerant and who may perform each

Your checkpoint

Timed 50-question mixed Type II/Type III exam scored at 85% or higher, with the comparison table submitted as the study artifact.

Week 6

Universal (Types I, II, and III)

  • Combine Core, Type I, Type II, and Type III rules into single decisions on whole-system scenarios

  • Identify safety hazards and controls: frostbite, asphyxiation, oxygen displacement, cylinder hydrostatic testing, and overfilling

  • Recognize refrigerant cylinder markings, colors, DOT transport rules, and storage limits

  • Apply date-based and refrigerant-based distinctions, including appliances built before and after November 15, 1993, and very high-pressure systems

Your checkpoint

Full-length 80-question Universal practice exam scored at 80% or higher with an item-by-item error log.

Week 7

Universal (Types I, II, and III) & Type II - High-Pressure Appliances & Type III - Low-Pressure Appliances

  • Rank weak topics by error frequency from the practice exam log

  • Re-drill the top three weak topics to 90% accuracy or better

  • Memorize the numeric threshold table (5 lb, 200 lb, 15/20/35%, 0 psig, 10 in Hg, 25 mm Hg) using spaced recall

  • Answer 25 questions in 20 minutes to build exam pacing

Your checkpoint

An error log showing every previously missed item answered correctly on two separate attempts.

Week 8

Universal (Types I, II, and III) & Type I - Small Appliances & Type II - High-Pressure Appliances & Type III - Low-Pressure Appliances

  • Complete two full-length timed Universal practice exams under test-day conditions

  • Write a one-line rationale for every flagged or guessed item

  • Re-verify the numeric thresholds and venting exceptions one final time without notes

  • Confirm test-day logistics: appointment, identification, and certification paperwork

Your checkpoint

Two consecutive Universal practice exams scored at 90% or higher.

Milestones

Week 2: Core + Type I quiz at 80% or higher, and the evacuation-level reference sheet recreated from memory without errors.

Week 4: Half-length mock covering Domains 1, 2, and 3 scored at 80% or higher.

Week 6: Full-length Universal practice exam at 80% or higher with every error logged and categorized.

Week 8: Two consecutive timed Universal practice exams at 90% or higher.

EPA 608 exam day

Your checklist

Government-issued photo ID

Bring a valid, unexpired ID with a name matching your registration. Confirm accepted ID forms with the testing provider. needs_review: exact ID requirements vary by provider.

Appointment confirmation and registration details

Have your confirmation number, test date/time, and provider contact information available, either printed or on your phone before check-in.

Testing-provider login credentials

For online-proctored exams, confirm your username/password and any required system check in advance. needs_review: confirm the exact login and launch procedure with your provider.

Know your exam sections

Confirm whether you are taking Core plus Type I, Type II, Type III, or Universal. Each section is typically scored separately.

Calculator policy

Confirm whether a basic calculator is allowed. Many providers supply an on-screen calculator or permit a basic model; do not assume. needs_review: calculator rules vary by provider.

Scratch paper and writing instrument

Most testing centers provide scratch paper and a pen/pencil. Do not bring your own unless the provider explicitly allows it.

Quiet, private test environment for online delivery

For online proctoring, use a quiet room with a clear desk, working webcam/microphone, stable internet, and no other people present.

Remove prohibited items

Phone, smartwatch, notes, books, and unauthorized devices must be put away or left outside the testing area. Confirm where to store them.

Arrival/check-in plan

Plan to arrive 15–30 minutes early for in-person testing, or log in early for online proctoring. needs_review: confirm the provider’s recommended arrival/check-in window.

Review the provider’s candidate handbook

Read the rules on conduct, breaks, scoring, retakes, and technical issues before exam day. needs_review: policies differ among EPA-approved certifying programs.

Plan the day

Final 72 hours

Confirm your appointment, ID requirements, delivery method, and provider rules. Review the Core section plus the Type section(s) you are taking. Take a practice test and note weak areas, especially refrigerant safety, environmental rules, recovery/recycling, and leak detection.

Final 24 hours

Do a light review of weak areas only. Prepare your ID and confirmation details. For online testing, run the system check, charge devices, and test your internet connection. Get a full night’s sleep.

Morning of the exam

Eat a normal meal, arrive or log in early, and avoid last-minute cramming. Keep your phone and other prohibited items away. Have your ID and confirmation ready for check-in.

During the test

Read each question carefully and answer every question. Flag uncertain items and return to them if the platform allows. Use scratch paper for calculations. Manage your time so you can review before submitting. If a technical problem occurs, notify the proctor immediately.

Rules to check

  • Bring a valid government-issued photo ID whose name matches your registration. Confirm accepted ID forms with the provider.

  • The EPA 608 exam is generally closed-book. Do not use notes, books, phones, smartwatches, or other unauthorized aids. Confirm the calculator policy with your provider.

  • Follow all proctor instructions. For online testing, stay in camera view, keep the room clear, and ensure no other people are present.

  • Ask the provider about the break policy before exam day. Breaks may be limited, may not stop the timer, or may not be allowed during a section.

  • Most EPA-approved programs require a passing score on Core and on each Type section separately. Confirm the exact cut score, retake waiting period, and fee policy with your provider.

  • Do not share, reproduce, or discuss specific exam questions after the test.

  • Arrive on time. Late arrival may result in forfeiture of your seat or fee; confirm the provider’s late-arrival policy.

  • If a technical issue occurs during an online exam, stop and contact the proctor or provider support immediately rather than troubleshooting alone.

EPA 608 FAQ

How many EPA 608 practice questions are available?

The practice set has 199 EPA 608 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many EPA 608 flashcards are available?

The flashcard set has 32 EPA 608 cards. Each card shows the term and its definition.

Which topics does the EPA 608 study material cover?

The EPA 608 study material has 4 sections, including Type I - Small Appliances, Type II - High-Pressure Appliances, and Type III - Low-Pressure Appliances.

What format facts does the catalog list for the EPA 608 exam?

The catalog lists these item types: multiple choice for the EPA 608 exam.