ASE G1 Practice Test

ASE G1 - Auto Maintenance and Light Repair

ASE G1 overview

  • 200 practice questions
  • 32 flashcards
  • 8 study guide topics
  • 36 key terms

What you'll study

  • Engine Systems12.5%
  • Automatic Transmission and Transaxle12.5%
  • Manual Drive Train and Axles12.5%
  • Suspension and Steering12.5%
  • Brakes12.5%
  • Electrical and Electronic Systems12.5%
  • Heating, Ventilation and Air Conditioning12.5%
  • Engine Performance12.5%

ASE G1, part of the ASE Certification Test Series administered by the National Institute for Automotive Service Excellence, is a multiple-choice credential for automotive service professionals who perform maintenance and light repair work - the routine services and inspections that make up a large share of everyday shop traffic. It is aimed at technicians early in their careers, at entry-level graduates moving into a dealership or independent shop, and at working techs who want a single credential that documents broad, practical competency rather than deep specialization. Because the content is deliberately broad, the test samples across eight areas: engine systems, automatic transmission and transaxle, manual drive train and axles, suspension and steering, brakes, electrical and electronic systems, heating, ventilation and air conditioning, and engine performance. Questions are written to be vehicle-generic, so preparation means understanding systems and diagnostic reasoning, not memorizing a particular make or model. ASE publishes study guides and an official practice test program, offers a free test drive of the testing experience, and hosts training through ASE Campus; accredited training providers are also listed on the ASE site. Candidates register through the ASE website and manage scheduling, results and renewals in a myASE account. Verify all current test details on ase.com before you register.

Common mistakes

Using an ohmmeter on a live circuit, or judging a high-current cable or ground by resistance reading instead of doing a loaded voltage-drop test.

Early training drills 'check continuity/ohms' as the default electrical test, so the meter gets used on circuits that are powered or on cables where a fraction of an ohm is normal and meaningless at meter current.

What to do instead

Before every resistance test, key off and disconnect the component; for starters, grounds and battery cables, use a DVOM on the volts scale and measure drop while the circuit is loaded (target under 0.5 V per connection, under 0.2 V per cable).

Bleeding an ABS-equipped brake system by pedal pumping alone and never commanding an ABS bleed or cycling the pump, then releasing the vehicle with a spongy pedal.

Air trapped in the hydraulic control unit or accumulator cannot be pushed out through the wheel cylinders by pedal force, and the candidate assumes 'pedal is firm enough' or that the scan tool step is optional.

What to do instead

Follow the OEM sequence exactly: bench-bleed or prime the master cylinder, bleed wheels in the specified order, and perform the scan-tool ABS bleed/valve cycling procedure; keep the reservoir above minimum and recheck pedal height on a test drive.

Reading fuel trims as the fault rather than as the PCM's correction, and condemning an oxygen sensor or fuel pump because long-term trim is high positive.

The trim number looks like a measurement of mixture, so a lean-reading sensor or a vacuum leak both point at the same number; the candidate picks the part that is easiest to reach.

What to do instead

Interpret the trim as the direction of correction, then prove the cause: introduce propane or carb cleaner at suspect intake points and watch for a trim swing, check fuel pressure and volume under load, and compare upstream sensor switching before replacing anything.

Diagnosing a misfire as ignition and installing coils and plugs without ever running a compression or cylinder-balance test, then returning the vehicle still misfiring.

Ignition is the most familiar misfire cause and the misfire code names a cylinder, which feels like a diagnosis; compression and mechanical checks are skipped as time-consuming.

What to do instead

Do a relative compression or cranking compression check and a cylinder balance/power-balance test early, verify spark with a spark tester and injector pulse with a noid light, then move to ignition only after mechanical health is confirmed.

Charging an A/C system by gauge pressure alone to 'get the vent cold', without recovering and weighing the charge and without running a leak check.

Low-side pressure depends heavily on ambient and engine speed, so a partial charge can look close to spec on the manifold gauge set, and the customer only complains after the refrigerant leaks out again.

What to do instead

Recover, evacuate and recharge by weight to the underhood specification, add the specified oil amount, and confirm with an electronic or UV leak check plus vent-temperature and pressure-performance readings before releasing the vehicle.

Starting an alignment or setting toe without first inspecting ball joints, tie-rod ends, control-arm bushings and wheel bearings, and without checking tire pressures and ride height.

The alignment rack produces camber and toe numbers quickly, so the candidate adjusts to spec on a worn front end and the angles drift as soon as the vehicle is driven.

What to do instead

Perform a full pre-alignment inspection and shake test, correct tire pressures, check for accident damage and set the steering wheel and clock spring to center before measuring; replace worn parts and re-measure, and record thrust angle and setback.

Checking automatic transmission fluid level with the engine off and in Park, or on a vehicle that requires a specific fluid temperature and a scan-tool level check, then adding or draining fluid based on that reading.

The old dipstick-and-engine-off habit transfers from older units, while many late transmissions are checked with the engine running in a specific range, at a specified pan temperature, with a standpipe.

What to do instead

Look up the fluid level and fill procedure in service information first - engine state, gear range, fluid temperature window, and whether a scan tool or standpipe is required - then check, and top up with the exact specified fluid.

Testing a battery or alternator straight off a charger or after a jump start without removing surface charge, or load-testing a battery that is not fully charged and declaring it failed.

Surface charge holds voltage artificially high and an undercharged battery sags under load, so a healthy battery reads bad and a bad one reads good; these quick checks are done under time pressure.

What to do instead

Fully charge the battery, remove surface charge with a load or a few minutes of headlights, then test with a conductance tester and a load test; verify charging voltage and AC ripple at the battery with loads on and off before condemning the alternator.

Blaming a slipping clutch on a worn disc without checking release hydraulics, free play and adjustment, or topping off a limited-slip differential with ordinary gear oil and no friction modifier.

Clutch slip is automatically attributed to the friction disc, and differential fluid spec is treated as generic 'gear oil', when both faults present as symptoms the candidate has already seen once.

What to do instead

For a clutch, verify pedal free play, hydraulic release and fork travel, check for oil contamination at the bell housing, and measure disc and flywheel wear before removal; for differentials, use the specified fluid and add friction modifier when required for limited-slip units.

Doing a pad-only brake job: fitting new pads without measuring rotor thickness and runout against the discard spec, and installing pads without cleaning and lubricating the caliper slides with the correct high-temperature grease.

Pads are the visible worn part and pass inspection quickly, so rotor measurement and slide service are skipped; the result is noise, pulsation or a dragging caliper that comes back within weeks.

What to do instead

Measure every rotor with a micrometer and check runout and discard thickness against spec, machine or replace as required, service caliper slides and abutment clips with the specified lubricant, and verify with a road test and pedal check.

Exam requirements can change. Confirm current details with the exam provider.

ASE G1 practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Engine Systems

    An engine's coolant temperature gauge reads lower than normal after 20 minutes of highway driving, and the heater blows only warm air. Which condition best explains these symptoms?

    1. A radiator cap with a weak pressure spring
    2. A restricted heater core
    3. A coolant level that is too low
    4. A thermostat stuck open Correct answer.

    Explanation

    A thermostat that stays open lets coolant circulate through the radiator continuously, so the engine never reaches normal operating temperature and heater output stays weak. Coolant temperature that is too low after extended driving is the classic signature of this failure.

  2. Question 2Engine Systems

    In a multigrade oil labeled 5W-30, what does the 5W designate?

    1. The oil's viscosity grade at operating temperature
    2. The oil's recommended drain interval
    3. The oil's low-temperature flow rating Correct answer.
    4. The oil's API service classification

    Explanation

    The W in a multigrade oil stands for winter, and the number preceding it rates how the oil flows when cold. The number after the W describes viscosity at operating temperature, which in this case is the 30 grade.

  3. Question 3Engine Systems

    A restricted engine air filter most directly causes which condition?

    1. An excessively lean mixture at idle speed
    2. Over-advanced ignition timing under load
    3. Reduced airflow at high engine speed Correct answer.
    4. Higher-than-normal engine oil pressure at idle

    Explanation

    The air filter's job is to supply the engine with unrestricted air, so a clogged element limits airflow most noticeably when demand is highest, such as at high engine speed. The result is reduced power and sometimes a richer mixture under load.

  4. Question 4Engine Systems

    A spark plug removed from one cylinder is black and wet with oil. Which condition is the most likely cause?

    1. An ignition timing advance that is too great
    2. A spark plug heat range that is too hot
    3. Worn valve guides or piston rings Correct answer.
    4. An intake manifold vacuum leak at that runner

    Explanation

    Wet, oily deposits mean oil is entering the combustion chamber and not burning cleanly. Worn valve guides or worn rings are the usual sources of that oil, and further testing such as a wet compression test can separate them.

  5. Question 5Engine Systems

    A high-pitched squeal from the accessory drive that is loudest right after a cold start and then fades most likely indicates:

    1. A glazed or slipping drive belt Correct answer.
    2. A restricted PCV valve
    3. A worn timing chain tensioner
    4. A faulty coolant temperature sensor

    Explanation

    A belt whose friction surface is glazed or that is improperly tensioned slips under the load of the alternator and other accessories, producing a squeal that is worst on a cold start. Proper belt tension and pulley alignment are the first checks.

  6. Question 6Engine Systems

    What is the primary purpose of the positive crankcase ventilation (PCV) system?

    1. To relieve excess pressure from the cooling system
    2. To recirculate a portion of exhaust gas into the intake
    3. To add oil mist to the intake charge for upper-cylinder lubrication
    4. To route crankcase vapors into the intake to be burned Correct answer.

    Explanation

    Blowby gases that collect in the crankcase contain unburned hydrocarbons, and the PCV system meters them back into the intake so they are consumed in combustion. This also prevents pressure from building and pushing oil past seals.

  7. Question 7Engine Systems

    During a compression test, holding the throttle wide open while cranking mainly serves to:

    1. Prevent the ignition coil from firing
    2. Allow maximum air into the cylinder Correct answer.
    3. Raise engine oil pressure during cranking
    4. Keep the fuel injectors from firing

    Explanation

    Compression readings depend on how much air is trapped in the cylinder, so the throttle plate must be open to admit a full charge. Restricting the intake would lower every reading and give a false impression of mechanical wear.

  8. Question 8Engine Systems

    Why is a 50/50 mix of antifreeze and water normally used instead of pure antifreeze?

    1. Pure antifreeze transfers heat out of the engine better than water does
    2. Water carries heat better; antifreeze adds freeze and corrosion protection Correct answer.
    3. Water alone provides all the corrosion protection an aluminum engine needs
    4. Pure antifreeze has a lower freezing point than any water and antifreeze blend

    Explanation

    Water is a superior heat-transfer fluid, but it freezes at a high temperature and promotes corrosion. Ethylene glycol lowers the freezing point and contains inhibitors, and the 50/50 blend balances heat transfer with protection.

  9. Question 9Engine Systems

    While a cylinder leak-down test is being performed, air bubbles continuously rise in the radiator. What does this indicate?

    1. A leaking intake valve in that cylinder
    2. A leaking head gasket or a crack into the water jacket Correct answer.
    3. Worn piston rings in the cylinder being tested
    4. A restricted radiator core

    Explanation

    The leak-down tester pressurizes the cylinder with the valves closed, so escaping air is traced by where it appears. Bubbles in the cooling system mean the pressurized air has found a path into a water jacket, which points to the head gasket or a cracked casting.

  10. Question 10Engine Systems

    An engine overheats while idling in traffic with the A/C on but stays normal at highway speed, and the electric cooling fan never runs. Which is the most likely cause?

    1. A leaking heater core
    2. An open circuit or failed fan motor Correct answer.
    3. A radiator cap with a weak spring
    4. A thermostat stuck in the open position

    Explanation

    At highway speed ram air moves enough air through the radiator, but at a standstill the electric fan must do that job. Overheating only when stopped, combined with a fan that never runs, points to the fan circuit or motor.

  11. Question 11Engine Systems

    An oil pressure warning light flickers at a hot idle and goes out above 1500 rpm; the oil level is correct. What is the most likely cause?

    1. An oil viscosity that is too high
    2. A restricted engine air filter element
    3. A stuck-open engine thermostat
    4. Worn bearings or a weak oil pump Correct answer.

    Explanation

    Oil pressure falls as clearances open up and as pump output drops, and low pressure first becomes visible at idle when pump speed is lowest. Pressure that recovers as rpm rises is typical of excessive bearing clearance or a worn pump.

  12. Question 12Engine Systems

    Fuel pressure is within specification at idle but drops below specification under heavy load, and the vehicle loses power. Which is the most likely cause?

    1. A restricted fuel filter Correct answer.
    2. A clogged air filter element
    3. A failing ignition coil
    4. A leaking intake manifold gasket

    Explanation

    When fuel demand rises under load, a restricted filter or a weak pump cannot keep volume up, so pressure falls and the engine runs lean and loses power. Pressure that is normal at idle but drops under demand is the key clue.

  13. Question 13Engine Systems

    A P0302 misfire code follows cylinder 2. After the coil from cylinder 2 is moved to cylinder 4, the misfire moves to cylinder 4. What is indicated?

    1. A leaking fuel injector in cylinder 2
    2. A mechanical fault in cylinder 2
    3. A faulty ignition coil Correct answer.
    4. A faulty spark plug in cylinder 2

    Explanation

    The misfire followed the part that was moved, which is the definition of a part-specific failure. Because the coil was the component swapped, the coil is the cause.

  14. Question 14Engine Systems

    A spark plug with a heat range that is too hot for the application can cause:

    1. A lower-than-normal tip temperature
    2. Heavy carbon fouling of the spark plug insulator
    3. Pre-ignition and electrode burning Correct answer.
    4. Oil fouling of the electrodes

    Explanation

    A hot plug conducts less heat away from the tip, so it runs above its designed temperature and can glow hot enough to ignite the mixture before the spark occurs. The result is pre-ignition, blistered insulators and burned electrodes.

  15. Question 15Engine Systems

    A vacuum gauge on the intake manifold reads normal at idle but drops steadily while the engine is held at 2500 rpm. Which condition is most likely?

    1. A cracked spark plug insulator
    2. A worn timing chain
    3. A restricted exhaust system Correct answer.
    4. A lean fuel mixture

    Explanation

    As exhaust flow increases with engine speed, a restricted converter or crushed pipe causes backpressure to build and manifold vacuum to fall. A vacuum reading that is normal at idle and declines with speed is a classic indicator of exhaust restriction.

  16. Question 16Engine Systems

    A ticking noise from the top of the engine that is loudest at startup and quiets once oil pressure builds most likely indicates:

    1. An exhaust manifold gasket leak
    2. A collapsed lifter Correct answer.
    3. A worn connecting rod bearing
    4. A loose spark plug

    Explanation

    Hydraulic lifters rely on oil pressure to maintain zero lash, so one that bleeds down overnight ticks until it refills. Noise that disappears as pressure builds is the characteristic pattern of a weak or collapsed lifter.

  17. Question 17Engine Systems

    After a coolant drain and refill, the engine overheats and the heater stays cold. Which is the most likely cause?

    1. A thermostat that opens too early
    2. Air trapped in the cooling system Correct answer.
    3. An antifreeze concentration that is too high
    4. A radiator cap rated too low

    Explanation

    Air pockets block coolant circulation, so the water pump cannot move liquid through the heater core or past the temperature sensor, and the engine overheats while the heater blows cold. The system must be bled at the specified points after a refill.

  18. Question 18Engine Systems

    On an interference engine, a timing belt that breaks while the engine is running will most likely cause:

    1. Valve-to-piston contact and major damage Correct answer.
    2. A coolant leak at the water pump
    3. An engine stall with no internal damage
    4. A blown head gasket only

    Explanation

    In an interference design the valves and pistons occupy the same space at different points in the cycle, and only the belt keeps them synchronized. Losing the belt lets pistons strike open valves, bending stems and often damaging guides and piston crowns.

  19. Question 19Engine Systems

    A vacuum gauge connected to the intake manifold reads a steady 10 in-Hg at idle, where specification is 18 to 22 in-Hg. Which is the most likely cause?

    1. A vacuum leak or retarded valve timing Correct answer.
    2. A glazed drive belt
    3. A weak battery
    4. A restricted exhaust system

    Explanation

    Manifold vacuum depends on the throttle restriction and on how efficiently the cylinders pump air. A leak admits unmetered air and late valve timing reduces pumping, so either condition produces a steady low reading.

  20. Question 20Engine Systems

    What is the purpose of the pressure rating marked on a radiator cap?

    1. It sets the maximum coolant temperature
    2. It controls when the thermostat opens
    3. It raises the coolant boiling point Correct answer.
    4. It limits coolant flow through the heater core

    Explanation

    Coolant boils at a higher temperature when the system is held under pressure, so the cap's spring rating determines the pressure the system maintains. A higher-rated cap raises the boiling point, allowing the engine to run hotter without boiling over.

  21. Question 21Engine Systems

    The fluid in a combustion gas (block) tester turns from blue to yellow while the engine is running. What does this indicate?

    1. The thermostat is stuck open
    2. Combustion gases are entering the cooling system Correct answer.
    3. The coolant is diluted with too much water
    4. The cooling system has an external leak

    Explanation

    The test fluid changes color when it contacts carbon dioxide, which is present in combustion gas but not normally in the cooling system. A color change confirms that cylinder pressure is escaping past the head gasket or through a crack into a water jacket.

  22. Question 22Engine Systems

    A cylinder produces 120 psi on a dry compression test and 165 psi after oil is added. What does this indicate?

    1. A leaking intake valve
    2. A blown head gasket
    3. Worn piston rings Correct answer.
    4. A worn camshaft lobe

    Explanation

    Oil temporarily seals the gap between rings and cylinder walls, so a large jump in the wet reading shows that pressure was escaping past the rings. Valve or gasket leaks do not seal appreciably when oil is added.

  23. Question 23Engine Systems

    During a cylinder balance test, disabling the injector for cylinder 3 causes no measurable drop in engine speed. What does this indicate?

    1. The overall fuel mixture is too lean
    2. Cylinder 3 is producing too much power
    3. The ignition timing is retarded
    4. Cylinder 3 is not producing power Correct answer.

    Explanation

    Each working cylinder contributes a share of engine power, so cutting its fuel should cause a noticeable rpm drop. When there is no change, that cylinder was already contributing nothing because of a spark, fuel or mechanical fault.

  24. Question 24Engine Systems

    Long-term fuel trim is +28% on both banks at idle and returns to near 0% at 2500 rpm. Which is the most likely cause?

    1. Low fuel pump pressure
    2. A vacuum leak in the intake Correct answer.
    3. Leaking fuel injectors
    4. A restricted exhaust system

    Explanation

    Unmetered air entering the intake has its greatest effect at idle, when the metered air charge is small, so the PCM adds fuel to compensate. When the leak becomes a smaller fraction of total airflow at higher rpm, the correction returns toward normal.

  25. Question 25Engine Systems

    A vehicle sets a P0016 camshaft/crankshaft correlation code and runs poorly. Which is the most likely cause?

    1. A weak ignition coil
    2. A clogged fuel filter
    3. A slow-responding oxygen sensor
    4. A stretched timing chain Correct answer.

    Explanation

    The code is set when the camshaft position no longer agrees with the crankshaft position within the expected window. Wear or stretch in the timing chain, or a jumped tooth, shifts cam timing and is the most common mechanical cause.

  26. Question 26Automatic Transmission and Transaxle

    Which statement describes the primary job of the torque converter?

    1. It locks the engine to the driveline whenever the throttle closes
    2. It changes the gear ratio at each shift point
    3. It multiplies torque at low speed and lets the engine idle in gear Correct answer.
    4. It provides engine braking in every forward gear

    Explanation

    The converter is a fluid coupling: the impeller throws oil into the turbine to move the car, and the stator redirects the returning oil so torque is multiplied at low speed. Because the coupling is fluid, the engine can idle while the car is held stationary in gear. Gear ratio changes are made by the planetary gearsets, not the converter.

  27. Question 27Automatic Transmission and Transaxle

    When is automatic transmission fluid level normally checked on a vehicle with a dipstick?

    1. Engine off, fluid cold, vehicle on a lift
    2. Engine idling in park, fluid hot, vehicle level Correct answer.
    3. Engine idling in drive, wheels blocked, fluid cold
    4. Engine off, fluid hot, after a 20-minute soak

    Explanation

    Most dipstick-equipped units are checked with the engine running so the pump keeps the converter and cooler full, with fluid at operating temperature and the car on a level surface. Checking with the engine off or cold gives a false reading because fluid drains back from the converter and cooler.

  28. Question 28Automatic Transmission and Transaxle

    What keeps the vehicle from rolling when Park is selected?

    1. A sprag holding the planetary carrier
    2. Line pressure applied to the forward clutch
    3. A band tightened around the output drum
    4. A pawl engaged in a toothed gear on the output shaft Correct answer.

    Explanation

    Park engages a spring-loaded parking pawl into notches on a park gear that is splined to the transmission output shaft, mechanically locking the driveline. The pawl is released by the manual valve linkage when the shifter leaves Park. No hydraulic apply device is used to hold the car in Park.

  29. Question 29Automatic Transmission and Transaxle

    Why does the torque converter clutch engage at steady cruise?

    1. To remove converter slip and improve fuel economy Correct answer.
    2. To cushion the driveline on wide-open-throttle shifts
    3. To let the engine idle without dragging the car
    4. To multiply engine torque during acceleration

    Explanation

    Above a calibrated speed and load, the converter clutch locks the turbine to the impeller so there is no slip, cutting heat and fuel use. Torque multiplication is the stator's job during acceleration, not something the clutch provides.

  30. Question 30Automatic Transmission and Transaxle

    How does a belt-drive CVT change its drive ratio?

    1. It engages different planetary gearsets
    2. It varies the working diameter of the two pulleys Correct answer.
    3. It slips a wet clutch to a controlled degree
    4. It switches between two fixed final-drive ratios

    Explanation

    In a belt or chain CVT, hydraulic pressure moves the halves of each pulley together or apart, changing the radius the belt rides on and therefore the ratio. Ratio change is stepless and continuous rather than a series of fixed steps.

  31. Question 31Automatic Transmission and Transaxle

    Which of these is an overdrive ratio?

    1. 1.00:1
    2. 3.20:1
    3. 0.70:1 Correct answer.
    4. 2.50:1

    Explanation

    An overdrive ratio is numerically less than 1.00:1, meaning the output shaft turns faster than the input. Ratios greater than 1.00:1 are reductions, and 1.00:1 is direct drive.

  32. Question 32Automatic Transmission and Transaxle

    What is the job of the manual valve?

    1. It routes line pressure to the circuits chosen by the shift lever Correct answer.
    2. It controls how fast a clutch applies during a shift
    3. It regulates line pressure according to engine load
    4. It locks the converter clutch at highway speed

    Explanation

    The manual valve is a spool moved by the shift lever through the cable or linkage. It does not regulate pressure; it simply sends line pressure to the circuits for the range the driver selected.

  33. Question 33Automatic Transmission and Transaxle

    Why is transmission fluid circulated through a cooler?

    1. To raise pressure before the fluid reaches the valve body
    2. To carry away heat made by the converter and clutches Correct answer.
    3. To separate air from the fluid before it returns to the pan
    4. To thicken the fluid so clutches hold better

    Explanation

    The converter and slipping clutches generate a lot of heat, and fluid temperature must be kept in a safe range to protect friction material and seals. The cooler, often inside the radiator plus an auxiliary unit, transfers that heat out.

  34. Question 34Automatic Transmission and Transaxle

    Stall speed is above specification in both Drive and Reverse. What does this most likely mean?

    1. The stator one-way clutch is slipping
    2. The converter clutch is stuck on
    3. Line pressure is low or an apply device is slipping Correct answer.
    4. The engine is down on power

    Explanation

    A stall test loads the engine against a held output. High stall speed in all ranges means the transmission cannot hold the engine, typically from low line pressure or slipping apply devices common to all ranges. Low stall speed, by contrast, points to an engine or stator problem.

  35. Question 35Automatic Transmission and Transaxle

    Line pressure reads low at idle in every range. Which is the most likely cause?

    1. A faulty pressure regulator valve or EPC solenoid Correct answer.
    2. A worn stator one-way clutch in the torque converter
    3. A leaking forward clutch piston seal inside the drum
    4. A misadjusted shift cable at the manual valve

    Explanation

    Line pressure is set by the pressure regulator and trimmed by the electronic pressure control solenoid. If pressure is low in every range, the fault is in a component that affects all circuits, such as the regulator, the EPC solenoid, or the pump. Range-specific leaks or linkage problems would not lower pressure everywhere.

  36. Question 36Automatic Transmission and Transaxle

    During an upshift, engine rpm rises briefly before the next gear takes hold. What is this condition and what does it mean?

    1. Flare, caused by a slipping or slow apply device Correct answer.
    2. Hunting, caused by a faulty shift solenoid
    3. Harsh engagement, caused by excessive line pressure
    4. Shudder, caused by converter clutch chatter at lockup

    Explanation

    Flare is a momentary loss of drive during a shift, seen as engine rpm climbing before the next ratio engages. It means the oncoming apply device is not holding full torque in time, from worn friction, a leaking seal, or low apply pressure.

  37. Question 37Automatic Transmission and Transaxle

    What does an accumulator do in a hydraulic valve body?

    1. It multiplies line pressure on wide-open-throttle shifts
    2. It vents excess pressure to the pan when fluid is cold
    3. It keeps the converter filled when the engine is off
    4. It cushions clutch apply to soften the shift Correct answer.

    Explanation

    An accumulator is a spring-loaded piston that absorbs part of the apply oil as a clutch fills, slowing the pressure rise and softening the shift. Once the piston bottoms, full apply pressure reaches the clutch.

  38. Question 38Automatic Transmission and Transaxle

    A simple planetary set has a 30-tooth sun gear and a 60-tooth ring gear. The ring gear is held, the sun gear is driven, and the carrier is the output. What is the ratio?

    1. 2.00:1
    2. 4.00:1
    3. 3.00:1 Correct answer.
    4. 1.50:1

    Explanation

    With the ring held and the sun driven, reduction equals 1 + (ring teeth / sun teeth). Here that is 1 + 60/30 = 3.00:1, so the carrier turns one revolution for every three input revolutions.

  39. Question 39Automatic Transmission and Transaxle

    A vehicle shudders as the converter clutch engages during light-throttle cruise. What is the most likely cause?

    1. A leaking output shaft seal
    2. A worn stator one-way clutch
    3. A slipping forward band
    4. Degraded fluid or a contaminated clutch facing Correct answer.

    Explanation

    Shudder during lockup comes from the clutch grabbing and releasing instead of applying smoothly. Degraded fluid, friction modifier depletion, or a contaminated converter clutch facing are the usual causes.

  40. Question 40Automatic Transmission and Transaxle

    Which solenoid sends fluid to the shift valves to change gears?

    1. The shift solenoid Correct answer.
    2. The line pressure switch
    3. The converter clutch solenoid
    4. The electronic pressure control solenoid

    Explanation

    Shift solenoids are turned on and off by the control module to direct or release fluid at the shift valves, which then apply and release the clutches and bands. The converter clutch solenoid and the EPC solenoid control different circuits.

  41. Question 41Automatic Transmission and Transaxle

    The owner's manual calls for a specific ATF, but the shop only stocks a universal fluid. What should be done?

    1. Use engine oil of the same viscosity until the correct fluid arrives
    2. Mix two different ATFs to approximate the required specification
    3. Use the universal fluid, since all ATFs are interchangeable
    4. Use a fluid meeting the manufacturer's specification Correct answer.

    Explanation

    Friction characteristics and seal compatibility are engineered for each unit, so the fluid must meet the published specification. A fluid that carries the correct approval is acceptable even if it is sold as a multi-vehicle product; an unapproved fluid is not.

  42. Question 42Automatic Transmission and Transaxle

    What is the usual procedure for adjusting an automatic transmission band?

    1. Adjust until the band drags heavily on the drum
    2. Tighten to the specified torque, then back off the specified turns Correct answer.
    3. Tighten the screw fully and lock it with the jam nut
    4. Back the screw out fully and let line pressure seat the band

    Explanation

    Band adjustment sets a specific clearance between band lining and drum. The adjusting screw is torqued to seat the band, then backed off a stated number of turns to establish that clearance before the locknut is tightened.

  43. Question 43Automatic Transmission and Transaxle

    ATF is leaking at the left front wheel area of a front-drive transaxle. What is the most likely source?

    1. A leaking transmission pan gasket
    2. A worn differential axle output shaft seal Correct answer.
    3. A failed torque converter hub seal
    4. A cracked transmission cooler line

    Explanation

    On a transaxle, the halfshaft passes through a seal at the differential output; a worn seal or a damaged joint boot area lets ATF escape at the wheel. Converter and pan leaks show up at the bellhousing and pan, not out at the wheel.

  44. Question 44Automatic Transmission and Transaxle

    A car's engine will start with the shifter in Drive as well as in Park and Neutral. What is the most likely cause?

    1. A bad brake pedal switch
    2. A shorted ignition switch
    3. A faulty starter motor
    4. A misadjusted or faulty transmission range sensor Correct answer.

    Explanation

    The range sensor tells the control module which range is selected and enables cranking only in Park and Neutral. If it reports Park/Neutral while the lever is in Drive, the starter will crank in gear.

  45. Question 45Automatic Transmission and Transaxle

    What does the stator do in a torque converter?

    1. Locks the turbine to the impeller at cruise speed
    2. Absorbs engine torsional vibration at idle
    3. Drives the transmission oil pump through the hub
    4. Redirects turbine oil back to the pump to multiply torque Correct answer.

    Explanation

    The stator sits on a one-way clutch between the turbine and impeller. At low speed it stays stationary and redirects oil leaving the turbine so it assists impeller rotation, which multiplies torque; at coupling speed it freewheels.

  46. Question 46Automatic Transmission and Transaxle

    The fluid on the dipstick is dark and smells burnt. What does this indicate and what should be done?

    1. Normal fluid life; top off and return the car
    2. Correct fluid for a CVT; no action needed
    3. Too much fluid; drain to the full mark and release
    4. Overheated fluid; find the cause and repair as needed Correct answer.

    Explanation

    A burnt smell and dark color mean the fluid has been overheated, which usually comes from slipping apply devices, a restricted cooler, or heavy loading. The cause must be found, since new fluid alone will overheat again.

  47. Question 47Automatic Transmission and Transaxle

    A planetary set has a 24-tooth sun gear and a 72-tooth ring gear. The sun is held, the ring is driven, and the carrier is the output. What is the ratio?

    1. 0.75:1 Correct answer.
    2. 1.33:1
    3. 4.00:1
    4. 3.00:1

    Explanation

    With the sun held and the ring driven, the ratio is ring teeth divided by the sum of ring and sun teeth: 72 / (72 + 24) = 0.75:1. A result below 1.00:1 is overdrive, so the carrier turns faster than the ring.

  48. Question 48Automatic Transmission and Transaxle

    A transaxle moves normally in Reverse but will not move in any forward range. What is the most likely cause?

    1. A faulty converter clutch solenoid
    2. A failed forward clutch or forward one-way clutch Correct answer.
    3. A worn stator one-way clutch
    4. A failed low/reverse band

    Explanation

    A component common to all forward ranges but not used in Reverse is the likely fault, and the forward clutch and its one-way clutch fit that description. Reverse still works because it uses the low/reverse band and a different torque path.

  49. Question 49Automatic Transmission and Transaxle

    What does raising throttle valve (modulator) pressure accomplish?

    1. Raises line pressure and delays upshifts under load Correct answer.
    2. Applies the converter clutch sooner at cruise
    3. Lowers line pressure to soften light-throttle shifts
    4. Lowers governor pressure to advance the shift points

    Explanation

    Throttle pressure rises with engine load and acts on the pressure regulator and shift valves. Higher throttle pressure raises line pressure for greater holding force and raises the speed at which upshifts occur.

  50. Question 50Automatic Transmission and Transaxle

    An engine stalls as the car comes to a stop in Drive, then restarts and drives fine. What is the most likely cause?

    1. A low/reverse band that is dragging badly
    2. A worn transmission oil pump
    3. The transmission has entered limp-home mode
    4. A converter clutch that stays applied Correct answer.

    Explanation

    If the converter clutch does not release as the vehicle slows, the engine is mechanically tied to the driveline and is dragged to a stall at a stop. Releasing the brake or shifting to neutral restores idle, which matches the complaint.

  51. Question 51Manual Drive Train and Axles

    A clutch release (throwout) bearing that is failing will typically produce which symptom?

    1. A whine that increases with vehicle speed in all gears
    2. A groan that occurs only while accelerating in fourth gear
    3. A whirring or growling noise when the clutch pedal is depressed Correct answer.
    4. A clicking noise that changes with engine RPM in neutral with clutch engaged

    Explanation

    In a conventional push-type clutch, the release bearing is loaded only while the pedal is depressed, so a worn bearing growls or whines as soon as the pedal is applied and typically quiets when it is released.

  52. Question 52Manual Drive Train and Axles

    Excessive clutch pedal free play on a mechanically linked clutch typically causes which condition?

    1. The release bearing to ride constantly on the pressure plate
    2. The clutch slips under acceleration
    3. The clutch may not fully release, causing gear clash Correct answer.
    4. Hydraulic fluid to bypass the master cylinder seal

    Explanation

    Free play is the clearance that lets the release bearing retract fully; too much of it uses up pedal travel before the pressure plate is unloaded, so the disc keeps dragging and the gears clash.

  53. Question 53Manual Drive Train and Axles

    Which symptom indicates a worn ring gear on the flywheel?

    1. Chatter when releasing the clutch from a stop
    2. Grinding while the engine is being cranked Correct answer.
    3. A steady vibration at highway speed
    4. A whine in all gears except fourth

    Explanation

    The starter pinion meshes with the flywheel ring gear, so chipped or worn teeth make the starter grind or screech during cranking.

  54. Question 54Manual Drive Train and Axles

    A torn CV joint boot will most likely result in which condition?

    1. Difficulty engaging reverse gear
    2. Increased ring and pinion backlash
    3. A leak at the pinion seal
    4. Rapid joint wear and failure Correct answer.

    Explanation

    The boot keeps grease in and abrasive dirt out; once it is torn the joint loses lubricant and is contaminated, so it wears quickly and eventually fails.

  55. Question 55Manual Drive Train and Axles

    Which component is clamped between the flywheel and the pressure plate?

    1. The input shaft seal
    2. The clutch disc Correct answer.
    3. The release bearing
    4. The pilot bearing

    Explanation

    The clutch disc is splined to the input shaft and is squeezed between the flywheel and pressure plate friction surfaces, so engine torque is carried through friction.

  56. Question 56Manual Drive Train and Axles

    Which symptom indicates a worn universal joint?

    1. A grinding noise during braking
    2. A whine that changes with engine RPM
    3. A steady vibration at idle
    4. A clunk when reversing direction Correct answer.

    Explanation

    A worn universal joint develops clearance in its needle bearings, so it clunks as driveline torque reverses direction and may squeak from lack of lubricant.

  57. Question 57Manual Drive Train and Axles

    On a front-engine, rear-wheel-drive vehicle, which component carries torque from the transmission output to the differential?

    1. The release fork
    2. The driveshaft Correct answer.
    3. The input shaft
    4. The half shaft

    Explanation

    In a rear-drive layout the driveshaft transfers torque from the transmission output shaft rearward to the differential pinion yoke.

  58. Question 58Manual Drive Train and Axles

    Before installing a new clutch, which component should be checked for cracks, heat damage, and surface finish?

    1. The flywheel Correct answer.
    2. The differential carrier
    3. The slip yoke
    4. The output shaft

    Explanation

    The flywheel friction face is the mating surface for the new disc, so cracks, heat checks, and grooves must be corrected or the new clutch will chatter or slip.

  59. Question 59Manual Drive Train and Axles

    A clutch hydraulic system that will not build firm pressure and has a spongy pedal most likely has which condition?

    1. Worn synchronizer blocking rings
    2. A leaking rear main seal
    3. A warped pressure plate
    4. Air in the hydraulic system Correct answer.

    Explanation

    Air is compressible, so a pedal that feels spongy and never firms up indicates the system must be bled; a hydraulic leak would also produce these symptoms and lower the reservoir level.

  60. Question 60Manual Drive Train and Axles

    A manual transaxle grinds when shifted into one specific gear but all other gears engage smoothly. Which condition is most likely?

    1. A worn blocking ring on that gear Correct answer.
    2. Incorrect clutch pedal free play
    3. A leaking input shaft seal
    4. Insufficient differential lubricant

    Explanation

    Each gear has its own blocking ring, so a grind limited to a single gear points to a worn ring or damaged engagement teeth; a common fault such as a dragging clutch would affect every gear.

  61. Question 61Manual Drive Train and Axles

    In driveshaft terminology, what does phasing refer to?

    1. Alignment of the U-joint yokes Correct answer.
    2. Balancing the shaft on a lathe
    3. Setting pinion bearing preload
    4. The angle between the transmission and the differential

    Explanation

    The yokes at opposite ends of a shaft must lie in the same plane so the speed changes produced by the two joints cancel each other; if they do not, a vibration develops.

  62. Question 62Manual Drive Train and Axles

    Excessive ring and pinion backlash will most likely produce which symptom?

    1. A clunk when torque reverses Correct answer.
    2. A howl that is constant at all speeds
    3. A whine heard only during acceleration
    4. A whine heard only during deceleration

    Explanation

    Too much backlash lets the ring gear rock between the drive and coast sides of the pinion, producing a clunk when the driver tips into and out of the throttle; a whine instead points to a depth or pattern problem.

  63. Question 63Manual Drive Train and Axles

    On a differential that uses a collapsible spacer, pinion bearing preload is established by which action?

    1. Turning the carrier bearing adjusters
    2. Crushing the collapsible spacer with the pinion nut Correct answer.
    3. Measuring backlash with a dial indicator
    4. Adding or removing shims behind the pinion bearing

    Explanation

    The collapsible spacer crushes as the pinion nut is tightened, so preload is verified by measuring the torque required to rotate the pinion rather than by a simple tightening torque value.

  64. Question 64Manual Drive Train and Axles

    Gear lubricant leaking from the end of a rear axle tube behind the brake backing plate most likely indicates which condition?

    1. Excessive differential fluid
    2. A failed pinion seal
    3. A cracked differential cover
    4. A worn axle seal or bearing Correct answer.

    Explanation

    On a semi-floating axle, oil reaching the brake backing plate area has passed a worn axle seal, often because a worn wheel bearing lets the shaft move and damages the seal lip.

  65. Question 65Manual Drive Train and Axles

    On a part-time four-wheel-drive vehicle, operating in 4WD on dry pavement will most likely cause which condition?

    1. Excessive clutch pedal free play
    2. Driveline bind and tire scuffing Correct answer.
    3. Premature synchronizer wear in the transmission
    4. Reduced differential backlash

    Explanation

    A part-time transfer case has no center differential, so the front and rear drivelines must slip on a high-traction surface; the resulting wind-up causes binding, tire scuffing, and possible transfer case damage.

  66. Question 66Manual Drive Train and Axles

    Clutch chatter during engagement is most commonly caused by which condition?

    1. Excess clutch pedal free play
    2. Low transaxle lubricant
    3. A misadjusted shift linkage
    4. Oil contamination of the disc Correct answer.

    Explanation

    Chatter means the friction coefficient is fluctuating as the clutch takes up, usually because oil or grease has reached the disc facing or because the flywheel surface is not flat and clean.

  67. Question 67Manual Drive Train and Axles

    Using an API GL-5 gear lubricant in a transmission that specifies GL-4 can cause which condition?

    1. Clutch slippage
    2. Excessive ring and pinion backlash
    3. Increased bearing preload
    4. Damage to brass synchronizer rings Correct answer.

    Explanation

    GL-5 fluids carry a high level of sulfur-phosphorus extreme-pressure additive that can attack yellow metals such as synchronizer rings and thrust washers, so a GL-4 fluid is required where those parts are used.

  68. Question 68Manual Drive Train and Axles

    A clicking noise that occurs only while turning on a front-wheel-drive vehicle most likely indicates which condition?

    1. A worn wheel bearing
    2. A worn differential side bearing
    3. A failed inner CV joint boot
    4. A worn outer CV joint Correct answer.

    Explanation

    The outer CV joint articulates as the wheels steer, so a rhythmic click that appears only in turns, especially under power, points to a worn outer joint, often after a torn boot.

  69. Question 69Manual Drive Train and Axles

    A manual transaxle engages third gear but will not stay in it under acceleration. Which condition is most likely?

    1. Excessive differential backlash
    2. A misadjusted clutch cable
    3. Low lubricant level
    4. Worn shift fork or dog teeth Correct answer.

    Explanation

    A gear that engages but will not stay engaged under load usually has worn engagement teeth, a bent or worn shift fork, or a weak detent that lets the sleeve slide back out of mesh.

  70. Question 70Manual Drive Train and Axles

    After a ring and pinion replacement, the axle whines only under acceleration and the pitch changes with vehicle speed. Which condition is the most likely cause?

    1. Worn universal joints
    2. Insufficient lubricant
    3. Incorrect wheel bearing adjustment
    4. Incorrect pinion depth setting Correct answer.

    Explanation

    Pinion depth determines where the ring gear tooth contacts the pinion; an incorrect setting loads the wrong part of the tooth and produces a speed-related whine that changes with load.

  71. Question 71Manual Drive Train and Axles

    A manual transmission whines in every gear except fourth, where the noise disappears. Which condition is most likely?

    1. Worn countershaft or input bearings Correct answer.
    2. A worn output shaft bearing
    3. A worn pilot bearing
    4. A worn differential carrier bearing

    Explanation

    In direct drive the countershaft and its gears are unloaded, so noise that is present in all indirect gears but vanishes in fourth comes from the input shaft, countershaft, or its bearings.

  72. Question 72Manual Drive Train and Axles

    A vehicle develops a vibration that begins near 50 mph, is felt in the floor pan, and stops when the vehicle stops. Which condition is most likely?

    1. A worn pilot bushing
    2. A bent or imbalanced driveshaft Correct answer.
    3. Incorrect differential backlash
    4. A worn clutch release bearing

    Explanation

    A vibration that appears at a specific road speed, is felt through the floor, and continues while the vehicle moves is characteristic of driveshaft imbalance, a worn universal joint, or a bad center bearing.

  73. Question 73Manual Drive Train and Axles

    A manual transmission becomes jammed with two gears engaged at the same time. Which condition is the most likely cause?

    1. A weak detent spring
    2. A stretched shift cable
    3. Excessive synchronizer clearance
    4. A faulty interlock mechanism Correct answer.

    Explanation

    The interlock mechanism in the shift rails prevents two gears from being selected at once; if it is worn, broken, or incorrectly assembled, the transmission can lock in two gears.

  74. Question 74Manual Drive Train and Axles

    A vehicle with a clutch-type limited-slip rear axle chatters and shudders during low-speed turns. Which condition is the most likely cause?

    1. A worn pinion seal
    2. Excessive ring and pinion backlash
    3. Worn limited-slip clutch plates Correct answer.
    4. Improper axle bearing preload

    Explanation

    Clutch-type limited-slip units depend on friction plates and a friction modifier in the lubricant; glazed or worn plates, or a missing modifier, make the plates grab and release during slow turns.

  75. Question 75Manual Drive Train and Axles

    On a rear axle with tapered roller wheel bearings, why is correct bearing adjustment critical?

    1. Too much end play causes the differential to lock
    2. Too little end play stops the axle carrying weight
    3. Too much end play increases ring and pinion backlash
    4. Too little end play causes overheating Correct answer.

    Explanation

    Tapered roller bearings need a small specified end play or preload; insufficient clearance makes them run hot, discolor, and fail prematurely, while excessive clearance lets the shaft walk.

  76. Question 76Suspension and Steering

    A vehicle's steering wheel turns, but the front wheels do not change direction. Which part most directly links the steering gear output to the front wheel assembly?

    1. The stabilizer link
    2. The tie rod Correct answer.
    3. The lower control arm
    4. The ball joint

    Explanation

    Tie rods carry the side-to-side motion of the steering rack or steering gear out to the steering knuckle. Ball joints are pivots, stabilizer links connect the sway bar, and control arms locate the knuckle. A broken or disconnected tie rod leaves the wheels pointing wherever they were last aimed.

  77. Question 77Suspension and Steering

    The forward or rearward tilt of the steering axis, viewed from the side of the vehicle, is called:

    1. Caster Correct answer.
    2. Toe
    3. Camber
    4. Thrust angle

    Explanation

    Caster is the side-view tilt of the steering axis, with positive caster leaning the top of the axis toward the rear. Toe and camber are measured from the front view, and thrust angle describes the rear axle's direction relative to the vehicle centerline.

  78. Question 78Suspension and Steering

    What is the primary job of a shock absorber or strut damper?

    1. To control spring oscillation Correct answer.
    2. To keep the tire bead seated on the rim
    3. To support the weight of the vehicle
    4. To hold the wheels at the correct alignment angle

    Explanation

    Springs store and release energy, so the damper converts that motion into heat and limits how many times the suspension bounces. Ride height is carried by the springs, not the dampers. Worn dampers show up as float, cupped tire wear, and poor body control.

  79. Question 79Suspension and Steering

    Why are tires rotated at the manufacturer's recommended interval?

    1. To keep the wheel fasteners properly torqued
    2. To equalize tread wear at each position Correct answer.
    3. To correct a pull to one side
    4. To increase the tire's load rating

    Explanation

    Front and rear positions wear at different rates because of drive torque, braking, and steering forces. Moving tires between positions spreads that wear so all four reach replacement depth together. Rotation does not fix a pull or change a tire's load rating.

  80. Question 80Suspension and Steering

    Which alignment angle is the difference between the distance across the front of the tires and the distance across the rear of the tires?

    1. Camber
    2. Caster
    3. Included angle
    4. Toe Correct answer.

    Explanation

    Toe compares the front and rear spacing of the tires at hub height; when the fronts are closer the setting is toe-in. Camber and caster are tilt angles measured from vertical and from the side view. Included angle is the sum of steering axis inclination and camber.

  81. Question 81Suspension and Steering

    Camber is the angle that describes:

    1. The difference in toe between the left and right wheels
    2. The fore-and-aft tilt of the steering axis
    3. The angle between the front wheels in a turn
    4. The lean of the wheel top from vertical Correct answer.

    Explanation

    Camber is viewed from the front of the vehicle and measures how far the top of the wheel leans in or out from true vertical. Positive camber leans the top outward and negative camber leans it inward. The side-view steering axis tilt is caster.

  82. Question 82Suspension and Steering

    In a recirculating-ball steering gear, the pitman arm is splined onto which shaft?

    1. The sector shaft Correct answer.
    2. The inner tie rod
    3. The steering knuckle spindle
    4. The idler arm shaft

    Explanation

    Steering wheel rotation turns the worm shaft, which drives the ball nut and rotates the sector shaft. The pitman arm is splined to that sector shaft and converts the rotation into a side-to-side push on the linkage. The idler arm is a separate support on the opposite frame rail.

  83. Question 83Suspension and Steering

    What is the function of a ball joint in a front suspension?

    1. It supports the vehicle weight through the wheel bearing
    2. It links the sway bar to the lower arm
    3. It forms a pivot between the control arm and knuckle Correct answer.
    4. It provides the toe adjustment

    Explanation

    A ball joint is a spherical pivot that lets the knuckle swing with suspension travel and steer left and right at the same time. It carries suspension loads but does not support the vehicle on the wheel bearing. Sway bar links and toe-adjusting sleeves are separate components.

  84. Question 84Suspension and Steering

    A tire shows diagonal, feathered wear across the tread ribs. Which condition most likely causes this?

    1. Worn shock absorbers
    2. Excessive positive camber
    3. Incorrect toe setting Correct answer.
    4. A wheel that is out of balance

    Explanation

    Toe error drags each tread rib sideways as the tire rolls, leaving a feathered or saw-toothed pattern you can feel with your hand. Camber error wears one shoulder heavily, and balance problems produce cupping or vibration rather than feathering. Checking and resetting toe is the repair.

  85. Question 85Suspension and Steering

    Tread on a front tire shows scalloped or cupped depressions around the circumference. Which is the most likely cause?

    1. Too much toe-in
    2. Incorrect caster setting
    3. Worn struts or shock absorbers Correct answer.
    4. Overinflated tires

    Explanation

    When damping is lost, the tire is allowed to bounce and slap the road, which scoops out scalloped depressions around the tread. Toe problems feather the tread, and overinflation wears the center rib. Caster does not cause a wear pattern of this type.

  86. Question 86Suspension and Steering

    A tire is worn evenly on both outer shoulders while the center tread is relatively unworn. What is the most likely cause?

    1. Overinflation
    2. Underinflation Correct answer.
    3. Excessive negative camber
    4. Excessive toe-in

    Explanation

    Low pressure lets the tire flex so the shoulders carry more load than the center, wearing both edges. Overinflation produces the opposite pattern with center wear. Camber error affects one shoulder only.

  87. Question 87Suspension and Steering

    A power steering system groans or whines whenever the wheel is turned at low speed. Which condition is the most likely cause?

    1. Worn outer tie rod ends with excessive play
    2. Low fluid or air in the system Correct answer.
    3. A loose pitman arm
    4. A failed strut bearing

    Explanation

    A groan that follows steering input is the classic sign of the pump cavitating because of low fluid or air pulled into the system. Bleeding the system and finding the leak is the correct next step. Mechanical play in the linkage causes looseness, not noise.

  88. Question 88Suspension and Steering

    A vehicle produces a growling noise that increases with road speed and becomes louder when turning to the left. Which component is most likely faulty?

    1. The left front wheel bearing
    2. The inner tie rod on the left side
    3. The right front wheel bearing Correct answer.
    4. The left front strut

    Explanation

    Turning left shifts weight onto the right side, which loads the right bearing and makes a bad bearing growl louder. A bearing that gets quieter when loaded is on the unloaded side. Tie rods and struts do not produce a speed-sensitive growl.

  89. Question 89Suspension and Steering

    A vehicle has about 3 inches of steering wheel free play before the front wheels begin to move. Which is the most likely cause?

    1. Worn tie rod ends Correct answer.
    2. Excessive positive caster setting
    3. A bent wheel
    4. Tires inflated below specification

    Explanation

    Free play at the rim means lost motion somewhere in the linkage or gear, most often worn tie rod ends, a worn idler arm, or loose steering gear lash. Caster and tire pressure change effort and feel but do not create rotational play. A bent wheel causes vibration or runout.

  90. Question 90Suspension and Steering

    A load-carrying lower ball joint is being inspected. Which method is generally recommended?

    1. With the weight on the joint Correct answer.
    2. Only with the suspension hanging free
    3. After removing it from the control arm
    4. Only with a pry bar under the tire

    Explanation

    A joint that carries the vehicle's weight must be checked with that weight on it, because the load seats the stud and hides looseness when the suspension hangs. Follower or load-free joints are checked with the suspension supported and the wheel unloaded. Knowing which type you are testing prevents a false diagnosis.

  91. Question 91Suspension and Steering

    The stabilizer (sway) bar link on one side of a front suspension has broken. What symptom will the driver notice?

    1. The alignment will not hold
    2. The steering will pull to one side
    3. The tires will wear on the inner edge
    4. More body roll and clunks over bumps Correct answer.

    Explanation

    The sway bar ties the two sides of the suspension together to limit body roll, and the link transmits that force. With a broken link, the bar is effectively disconnected, so the body leans more in corners and the loose parts rattle over bumps. It does not change static alignment or cause a steady pull.

  92. Question 92Suspension and Steering

    A vehicle shakes noticeably at 60 mph, but the vibration is not felt at low speed and does not change when turning. What is the most likely cause?

    1. An unbalanced wheel and tire Correct answer.
    2. A worn idler arm
    3. A leaking rack seal
    4. Incorrect caster setting

    Explanation

    Imbalance and runout show up as a shake that appears in a specific highway speed range and usually comes and goes as speed changes. A noise that changes with turning points to a bearing, not balance. Idler arm wear and caster errors affect steering feel rather than creating a speed-specific shake.

  93. Question 93Suspension and Steering

    Which component must be compressed with a spring compressor before a MacPherson strut can be disassembled?

    1. The jounce bumper
    2. The stabilizer bar
    3. The coil spring Correct answer.
    4. The tie rod

    Explanation

    The coil spring on a strut is held under heavy preload between the seats, so it must be captured with a compressor before the upper mount nut is released. Releasing that stored energy without a compressor can cause serious injury. The bumper, sway bar, and tie rod are not preloaded in the same way.

  94. Question 94Suspension and Steering

    An outer tie rod end is replaced on a front-wheel-drive vehicle. What must be done before the vehicle is returned to the customer?

    1. The wheels must be rebalanced
    2. The strut rod bushings must be replaced
    3. The toe setting must be checked and set Correct answer.
    4. The steering gear must be replaced

    Explanation

    The tie rod is the toe adjustment, so any change in its length alters toe on that wheel and usually moves the steering wheel off center. Toe must be measured and reset, and the steering wheel centered, before delivery. Wheel balance and steering gear replacement are not part of this repair.

  95. Question 95Suspension and Steering

    A rack-and-pinion boot (bellows) is torn and the inner tie rod is exposed. What is the most serious result if it is not repaired?

    1. The power steering pump will overheat
    2. The toe setting will change right away
    3. Dirt will ruin the rack seals Correct answer.
    4. The steering will become manual

    Explanation

    The boot keeps grit and water off the rack bore and the inner tie rod socket. Once it is torn, contaminants abrade the seals and the rack begins to leak and lose assist. A torn boot does not itself change toe or disable the pump.

  96. Question 96Suspension and Steering

    After an alignment, a vehicle's steering does not return to center and feels as though it 'remembers' a new straight-ahead position. Which component is the most likely cause?

    1. A seized strut bearing Correct answer.
    2. A leaking rack seal
    3. A worn inner tie rod socket
    4. Too little positive caster

    Explanation

    Memory steer occurs when a joint binds and holds the position it was last steered to, and a dry or seized upper strut bearing is a common cause. Caster provides the self-centering force, so too little caster causes poor return but not a stored position. Worn sockets and leaks cause play or fluid loss instead.

  97. Question 97Suspension and Steering

    Included angle is out of specification on the left front wheel, but camber can be brought within specification. Which is the most likely cause?

    1. A bent knuckle or strut Correct answer.
    2. A worn lower control arm ball joint
    3. Incorrect toe setting
    4. A weak coil spring

    Explanation

    Included angle is the sum of steering axis inclination and camber, so it is a diagnostic angle that cannot be adjusted. When camber reads correctly but included angle does not, the steering axis itself is bent, typically a bent knuckle or strut. Wear, toe, and spring sag do not change included angle this way.

  98. Question 98Suspension and Steering

    The rear thrust angle is 0.9 degrees and out of specification on a vehicle with a solid rear axle. What will the driver most likely notice?

    1. Heavy steering at low speed
    2. A highway-speed steering shake
    3. Dog tracking and off-center steering Correct answer.
    4. The front tires will cup

    Explanation

    Thrust angle is the direction the rear axle points relative to the vehicle centerline, and misalignment makes the rear of the vehicle track to one side. The driver compensates by turning the wheel, so it sits off center while the vehicle dog-tracks. It does not create a shake, cupping, or high steering effort.

  99. Question 99Suspension and Steering

    A vehicle wanders at highway speed and the steering returns to center poorly. Both front caster readings are well below specification. Which statement explains this?

    1. Lower caster reduces self-centering Correct answer.
    2. Caster has no effect on steering feel or stability
    3. Low caster raises parking effort
    4. Low caster increases shoulder wear

    Explanation

    Positive caster makes the steering axis lead the contact patch, creating a self-aligning torque that straightens the wheels and stabilizes the vehicle in a straight line. Less caster means less of that force, so the car wanders and the wheel does not return well. Caster does not drive tread wear or parking effort in the way toe, camber, and tire pressure do.

  100. Question 100Suspension and Steering

    On a test drive over a bumpy road, the toe setting changes as the suspension moves up and down, and the steering wheel darts. What is this condition called?

    1. Memory steer
    2. Bump steer Correct answer.
    3. Understeer
    4. Torque steer

    Explanation

    Bump steer is toe change through suspension travel, caused by tie rod geometry that does not match the control arm arcs, or by a lowered or damaged suspension. Torque steer is a pull under acceleration from unequal drive angles, memory steer is a binding joint, and understeer is a cornering balance condition.

  101. Question 101Brakes

    Which brake fluid is silicone-based and must never be mixed with glycol-based fluid?

    1. DOT 3
    2. DOT 5 Correct answer.
    3. DOT 4
    4. DOT 5.1

    Explanation

    DOT 5 is a silicone-based fluid and is not miscible with glycol-based fluids such as DOT 3, DOT 4, or DOT 5.1. Mixing the two can cause aeration and seal swelling, so the entire system must be flushed if the fluid type is changed.

  102. Question 102Brakes

    A disc brake pad has a metal tab that contacts the rotor as the lining wears down. What is the purpose of this tab?

    1. To center the pad in the caliper bracket
    2. To keep the pad square to the rotor
    3. To warn the driver that pads are worn Correct answer.
    4. To damp noise on light application

    Explanation

    The wear indicator is a metal tab that touches the rotor once the lining is nearly gone, producing an audible squeal. The noise warns the driver to service the brakes before the backing plate damages the rotor.

  103. Question 103Brakes

    Which tool is used to measure disc brake rotor thickness?

    1. Dial indicator
    2. Torque wrench
    3. Micrometer Correct answer.
    4. Tape measure

    Explanation

    Rotor thickness is measured with a micrometer that reads to 0.01 mm (0.001 in.) and compared with the minimum thickness cast or stamped on the rotor. A dial indicator measures lateral runout, not thickness.

  104. Question 104Brakes

    Insufficient brake pedal free play will most likely cause:

    1. A spongy, low pedal
    2. Excessive pedal free travel
    3. Dragging brakes and heat Correct answer.
    4. A hard, high pedal

    Explanation

    Free play lets the master cylinder piston return fully so the compensation port can vent fluid as it expands with heat. With too little play the port stays covered, pressure builds as the fluid warms, and the brakes drag and overheat.

  105. Question 105Brakes

    When manually bleeding a four-wheel hydraulic system with one bleeder screw per wheel, which wheel is bled first?

    1. Left rear
    2. Right front
    3. Left front
    4. Right rear Correct answer.

    Explanation

    Bleeding begins at the wheel farthest from the master cylinder and works toward the nearest, which on a left-hand-drive vehicle is right rear, left rear, right front, left front. This order pushes air out of the lines instead of driving it back through the system.

  106. Question 106Brakes

    A brake hose shows a soft bulge when the pedal is applied. What is the correct action?

    1. Wrap the bulge with protective sleeving
    2. Reduce pressure at the proportioning valve
    3. Clean the hose and recheck at the next service
    4. Replace the hose Correct answer.

    Explanation

    A bulge means the internal reinforcing braid has failed and the hose can burst under pressure. Brake hoses cannot be repaired or protected; the hose must be replaced.

  107. Question 107Brakes

    The red brake warning lamp stays lit after the parking brake is released and the fluid level is correct. Which component is most likely supplying the ground for the lamp?

    1. The ABS relay
    2. The stop lamp switch
    3. The pressure differential switch Correct answer.
    4. The cruise control module relay

    Explanation

    The pressure differential switch closes when pressure between the two hydraulic circuits is unequal, grounding the warning lamp. With the parking brake released and the reservoir full, a stuck switch or an actual circuit imbalance is the likely cause.

  108. Question 108Brakes

    Brake shoe lining is riveted to the shoe. Which condition means the lining must be replaced?

    1. Lining shows light scoring
    2. Lining is darker on one side
    3. Lining is close to the rivets Correct answer.
    4. Lining is glazed and shiny all over

    Explanation

    A riveted lining must be replaced before the rivets contact the drum and score it. The common limit is about 0.8 mm (1/32 in.) of lining remaining above the rivet heads.

  109. Question 109Brakes

    What is the primary function of a proportioning valve in a hydraulic brake system?

    1. Maintain residual pressure in the rear circuit
    2. Equalize pressure between the two circuits
    3. Hold off front pressure until the rear brakes apply
    4. Limit rear brake pressure during hard stops Correct answer.

    Explanation

    Weight transfer during hard braking reduces rear tire traction, so the proportioning valve limits rear hydraulic pressure to prevent rear wheel lockup. It does not control front brake pressure.

  110. Question 110Brakes

    A metering (hold-off) valve delays pressure to which brakes?

    1. Both circuits equally
    2. The parking brake circuit
    3. Front disc brakes Correct answer.
    4. Rear drum brakes

    Explanation

    The metering valve holds off front disc pressure until a small rear pressure is built, allowing the rear drum brakes to begin applying first. This balances the timing of front and rear brake application.

  111. Question 111Brakes

    A residual pressure check valve in a drum brake circuit typically holds how much pressure?

    1. 10 psi Correct answer.
    2. 0.5 psi
    3. 5 psi
    4. 2 psi

    Explanation

    About 10 psi is held in a drum brake circuit so the wheel cylinder cups stay seated and the return springs do not pull the shoes too far back. Disc circuits, where a valve is used, are limited to roughly 2 psi.

  112. Question 112Brakes

    Why is a new master cylinder bench bled before installation?

    1. To remove trapped air before installation Correct answer.
    2. To check the cylinder bore for scoring and wear
    3. To test the residual valve
    4. To seat the primary cup seal

    Explanation

    Bench bleeding pushes air out of the master cylinder before it can be driven into the lines, where it is much harder to remove. Skipping it commonly leaves a spongy pedal that is difficult to bleed out afterward.

  113. Question 113Brakes

    A steel brake line is rusted through on a straight section. Which repair is acceptable?

    1. Install a compression fitting at each end
    2. Use clamped rubber hose for the section
    3. Splice in copper tubing with flare nuts
    4. Double-flare a new section with a union Correct answer.

    Explanation

    Only a double flare or ISO flare joined with a proper union is acceptable for steel brake line repair. Compression fittings, copper tubing, and clamped rubber hose are not approved for hydraulic brake pressure.

  114. Question 114Brakes

    An ABS wheel speed sensor tip is covered with metallic debris. What is the most likely result?

    1. False ABS activation at low speed Correct answer.
    2. A consistently hard pedal
    3. The pump motor running continuously
    4. Rear wheel lockup only

    Explanation

    Debris on the sensor tip or tone ring distorts the signal, so the module sees a wheel speed that does not match the others and commands an unnecessary pressure release. The driver may feel the pedal pulse at low speed.

  115. Question 115Brakes

    Before servicing an ABS unit that uses a high-pressure accumulator, what should be done first?

    1. Open all four bleeder screws
    2. Pump the pedal with the ignition off Correct answer.
    3. Fill the reservoir to the top
    4. Disconnect the battery and wait 10 minutes

    Explanation

    An accumulator stores high-pressure fluid or nitrogen and can discharge during service. Pumping the brake pedal with the ignition off bleeds that stored pressure down to a safe level.

  116. Question 116Brakes

    A hydro-boost brake booster receives its power from:

    1. The ABS pump motor
    2. Engine intake manifold vacuum
    3. The power steering pump Correct answer.
    4. An electric vacuum pump

    Explanation

    A hydro-boost unit uses pressurized power steering fluid rather than engine vacuum to assist the brake pedal. This is common on diesel engines and on vehicles with little available vacuum.

  117. Question 117Brakes

    Brake fade during repeated hard stops from high speed is caused by:

    1. Glazing of the pad friction surface only
    2. A failing master cylinder cup
    3. Air entering the hydraulic system
    4. Heat that lowers the friction coefficient Correct answer.

    Explanation

    Repeated hard stops raise pad and rotor temperature until the friction material's coefficient drops, which shows up as a hard pedal with reduced stopping power. Allowing the brakes to cool restores most of the lost friction.

  118. Question 118Brakes

    What is the purpose of a height-sensing proportioning valve?

    1. Increase rear brake pressure when the vehicle is empty
    2. Balance front and rear on ABS-equipped vehicles
    3. Hold residual pressure on rear discs
    4. Reduce rear brake pressure as load decreases Correct answer.

    Explanation

    A height-sensing valve is linked to the rear suspension, so it trims rear pressure according to how heavily the vehicle is loaded. A lightly loaded vehicle needs less rear braking to avoid lockup.

  119. Question 119Brakes

    Some ABS systems require an automated bleed procedure. Which tool is needed?

    1. A scan tool with bidirectional control Correct answer.
    2. A pressure bleeder connected to the reservoir cap
    3. An ohmmeter
    4. A vacuum gauge

    Explanation

    An automated bleed cycles the ABS pump and solenoid valves, so the module must be commanded to run. That requires a scan tool capable of bidirectional control on that system.

  120. Question 120Brakes

    A pulsation is felt through the brake pedal and steering wheel during braking. What is the most likely cause?

    1. Air in the hydraulic system
    2. A weak rear drum shoe return spring
    3. Rotor thickness variation or runout Correct answer.
    4. A sticking caliper piston slide

    Explanation

    Uneven rotor thickness or lateral runout pushes the pads back and forth as the wheel turns, creating a pulsation in the pedal and steering wheel. Measuring runout and thickness with the proper tools confirms it.

  121. Question 121Brakes

    A leading-trailing drum brake is self-energizing because:

    1. The wheel cylinder applies both shoes equally
    2. The adjuster strut preloads the shoes
    3. Drum rotation drags the leading shoe inward Correct answer.
    4. Return springs add force to the shoes

    Explanation

    Friction between the leading shoe and the turning drum rotates the shoe about its anchor, wedging it more firmly against the drum. That wedging multiplies the applied force without extra hydraulic pressure.

  122. Question 122Brakes

    A quick take-up master cylinder is used to:

    1. Act as a residual pressure valve
    2. Store fluid for the ABS pump
    3. Shorten pedal travel on rear drum brakes
    4. Push low-drag caliper pistons out quickly Correct answer.

    Explanation

    Low-drag calipers use a knock-back spring or square-cut seal that retracts the piston further, so a larger volume of fluid is needed just to close the gap. The quick take-up cylinder supplies that volume through a stepped bore.

  123. Question 123Brakes

    On a vehicle with a diagonally split hydraulic system, a leak in one circuit will:

    1. Cause total loss of braking
    2. Disable only the rear brakes
    3. Have no effect on braking
    4. Leave two wheels braking Correct answer.

    Explanation

    A diagonally split system pairs one front wheel with the opposite rear wheel, so a leak in one circuit still leaves braking at two wheels. The pedal will travel further because one circuit is no longer building pressure.

  124. Question 124Brakes

    Which specification indicates a glycol-based fluid with the highest wet boiling point?

    1. DOT 2
    2. DOT 3
    3. DOT 5
    4. DOT 5.1 Correct answer.

    Explanation

    DOT 5.1 is a glycol-based fluid with a higher wet boiling point than DOT 3, which matters in severe service. DOT 5 is silicone and behaves differently, making it unsuitable for many ABS systems.

  125. Question 125Brakes

    With steady pressure held on the brake pedal at a stop, the pedal slowly sinks to the floor. What is the most likely cause?

    1. A master cylinder bypassing internally Correct answer.
    2. A leaking caliper piston dust boot
    3. Air trapped in the rear hydraulic circuit
    4. A misadjusted rear parking brake cable

    Explanation

    Cup seals that do not hold pressure let fluid slip past the piston, so the pedal gradually falls under a steady load. External leaks would show fluid loss, while air typically gives a spongy pedal rather than a slow sink.

  126. Question 126Electrical and Electronic Systems

    A fully charged 12-volt battery that has been resting for several hours with no load should show an open-circuit voltage of about:

    1. 12.0 volts
    2. 14.2 volts
    3. 12.6 volts Correct answer.
    4. 11.4 volts

    Explanation

    Each of the six cells in a fully charged lead-acid battery produces about 2.1 volts at rest, giving roughly 12.6 volts at the terminals. A reading near 12.0 volts indicates roughly 50 percent state of charge, and 11.4 volts indicates a deeply discharged battery. Values above about 13.2 volts at rest usually mean a surface charge that has not been removed.

  127. Question 127Electrical and Electronic Systems

    What is the primary job of a fuse in an automotive circuit?

    1. To hold a steady voltage at the load
    2. To store energy for the load
    3. To convert AC into DC
    4. To open the circuit on overload Correct answer.

    Explanation

    A fuse contains a calibrated element that melts and opens the circuit when current exceeds its rating, protecting the wiring and components from overheating. It does not regulate voltage or store energy. Once it opens, it must be replaced after the cause of the overload is corrected.

  128. Question 128Electrical and Electronic Systems

    Before a technician measures resistance with a digital multimeter, the circuit being tested should be:

    1. warmed to operating temperature
    2. isolated and unpowered Correct answer.
    3. connected to a battery charger
    4. loaded with a test light

    Explanation

    An ohmmeter supplies its own small reference current, so any outside voltage in the circuit will corrupt the reading and can damage the meter. The component or circuit must therefore be disconnected or the power removed before testing. Resistance tests also require good contact at both probe tips.

  129. Question 129Electrical and Electronic Systems

    In a series circuit containing three resistors, which quantity is the same through every component?

    1. Resistance
    2. Voltage
    3. Current Correct answer.
    4. Power

    Explanation

    A series circuit provides only one path for electron flow, so the same current passes through every component in the loop. The voltage divides across the resistors in proportion to their resistance, and power dissipated differs with each resistor's value. Resistance is a property of each individual component, not a shared value.

  130. Question 130Electrical and Electronic Systems

    Which headlamp type uses a high-voltage ballast to strike and maintain an arc?

    1. High-intensity discharge Correct answer.
    2. LED matrix
    3. Incandescent sealed beam
    4. Halogen

    Explanation

    High-intensity discharge lamps create light from an arc through a gas-filled capsule and need a ballast to supply a brief high-voltage pulse and then regulate running voltage. Halogen and sealed-beam lamps use a heated filament at normal system voltage. LEDs are driven by a low-voltage constant-current driver rather than an arc-striking ballast.

  131. Question 131Electrical and Electronic Systems

    A typical specification for maximum key-off parasitic draw on a late-model vehicle is about:

    1. 50 milliamps Correct answer.
    2. 500 milliamps
    3. 20 amps
    4. 5.0 amps

    Explanation

    After all modules have gone to sleep, normal key-off current draw is generally in the range of 20 to 50 milliamps, with some manufacturers allowing slightly more. Draw of 500 milliamps or more will drain a battery in a day or two. The measurement must be taken after the sleep delay has elapsed.

  132. Question 132Electrical and Electronic Systems

    On a standard ISO automotive relay, terminals 85 and 86 are connected to the:

    1. the case ground
    2. the coil winding Correct answer.
    3. the battery positive post
    4. the load contacts

    Explanation

    In the ISO numbering system, 85 and 86 are the two ends of the electromagnet coil, while 30 is the common feed and 87/87a are the switched contacts. Powering 85 and 86 energizes the coil and pulls the contacts closed. Identifying these terminals allows a technician to test the control side separately from the load side.

  133. Question 133Electrical and Electronic Systems

    To measure voltage drop across a starter ground cable while cranking, the DMM should be:

    1. set to amps and connected in parallel with the cable
    2. set to DC volts and connected across the cable Correct answer.
    3. set to AC volts and connected to the battery posts
    4. set to ohms and connected in series with the cable

    Explanation

    Voltage drop testing measures the difference in potential between the two ends of a conductor while normal current flows through it. The meter is set to DC volts and its leads are placed at each end of the cable, in parallel with it. A low reading means low resistance in that cable.

  134. Question 134Electrical and Electronic Systems

    A 12-volt circuit powers a 60-watt lamp. How much current does the lamp draw?

    1. 720 amps
    2. 5 amps Correct answer.
    3. 0.2 amp
    4. 12 amps

    Explanation

    Power equals voltage multiplied by current, so current equals power divided by voltage. Dividing 60 watts by 12 volts gives 5 amps. This value is used when selecting fuse ratings and wire gauge for the circuit.

  135. Question 135Electrical and Electronic Systems

    Two 12-ohm resistors connected in parallel produce a total resistance of:

    1. 6 ohms Correct answer.
    2. 12 ohms
    3. 24 ohms
    4. 0.5 ohm

    Explanation

    For two equal resistors in parallel, total resistance is half of one resistor's value, so 12 ohms divides to 6 ohms. The general formula multiplies the two values and divides by their sum. Adding a parallel path always lowers total resistance below the smallest individual resistor.

  136. Question 136Electrical and Electronic Systems

    A charging system on a warm engine at 2000 rpm measures 13.1 volts at the battery with all accessories off. The technician should:

    1. test the charging circuit for low output Correct answer.
    2. accept it as normal and release the vehicle
    3. replace the battery as the first step
    4. top up the battery with distilled water

    Explanation

    Most manufacturers specify roughly 13.5 to 14.8 volts at the battery under these conditions, so 13.1 volts is below normal. The technician should test alternator output, the sense circuit, and the charging cables before condemning any part. Replacing parts before testing risks a comeback.

  137. Question 137Electrical and Electronic Systems

    A vehicle does not crank. The battery is good, the headlamps are bright, and there is 0 volts at the starter solenoid S terminal with the key held in START. The most likely cause is:

    1. a battery that is discharged below 12 volts
    2. an open in the starter control circuit Correct answer.
    3. a seized engine that will not rotate
    4. worn brushes inside the starter motor

    Explanation

    If the battery and cables are sound but no voltage reaches the solenoid S terminal during cranking, the control circuit between the ignition switch and the solenoid is open. Possible causes include the ignition switch, neutral safety or clutch switch, relay, or a broken wire. Starter motor condition does not matter until the solenoid is being commanded.

  138. Question 138Electrical and Electronic Systems

    The large cable that carries alternator output to the battery is normally protected by:

    1. the ignition switch contacts
    2. a turn-signal flasher module
    3. a fusible link Correct answer.
    4. a 10-amp blade-type fuse

    Explanation

    Alternator output current can exceed 100 amps, so the circuit is protected by a fusible link or a high-current megafuse sized for that load. A small blade fuse would open immediately under charging current. The ignition switch does not carry or protect the main charge path.

  139. Question 139Electrical and Electronic Systems

    A blower motor runs on high speed only. Which is the most likely cause?

    1. a failed high-speed relay
    2. a shorted blower motor
    3. an open blower motor ground
    4. an open blower resistor Correct answer.

    Explanation

    Lower blower speeds are created by routing current through the blower resistor, while high speed bypasses it. If only high speed works, the resistor block or its lower-speed feed is open. The motor, its ground, and the high-speed circuit must be intact because high speed still operates.

  140. Question 140Electrical and Electronic Systems

    A CAN bus measured at the DLC with the key off reads 120 ohms. This reading indicates:

    1. a short to ground on CAN high
    2. one terminating resistor is open Correct answer.
    3. both terminating resistors are missing
    4. a normal, healthy bus

    Explanation

    A healthy CAN bus has two 120-ohm terminating resistors in parallel, so the meter should read about 60 ohms. A reading of 120 ohms means only one resistor is in the circuit, either because a resistor failed open or a bus wire is broken. A short would pull the reading far below 60 ohms.

  141. Question 141Electrical and Electronic Systems

    A customer reports an intermittent no-crank condition. Which DMM function best captures a brief voltage dip at the starter control terminal?

    1. continuity beep
    2. min/max recording Correct answer.
    3. resistance
    4. diode test

    Explanation

    The min/max function samples the input continuously and stores the highest and lowest values seen, so a momentary dip that a technician could not watch in real time is still captured. Continuity, resistance, and diode tests are performed on unpowered circuits and cannot monitor a live control signal. The recorded minimum is then compared with the expected cranking voltage.

  142. Question 142Electrical and Electronic Systems

    Both headlamps and the dash lights dim whenever the turn signal flashes, and the engine-to-body ground strap shows 0.8 volt drop under load. The cause is:

    1. a weak turn-signal flasher
    2. a shorted dash cluster
    3. an open headlamp switch
    4. a high-resistance engine ground strap Correct answer.

    Explanation

    Ground straps should show only a few hundredths of a volt of drop under load. A 0.8 volt drop means the strap has excessive resistance, so return current raises the ground reference for every load on that circuit. This produces the shared dimming seen when the turn signals add current to the path.

  143. Question 143Electrical and Electronic Systems

    Key-off draw measures 420 milliamps. Which is the best next step to isolate the source?

    1. pull fuses one at a time and watch the meter Correct answer.
    2. clean both battery terminals and retest the draw
    3. install a new battery and repeat the draw test
    4. replace the alternator with a high-output unit

    Explanation

    Removing fuses one at a time while monitoring the ammeter shows which circuit makes the excessive draw disappear, narrowing the fault to that branch. The technician must then recheck that the vehicle has fully gone to sleep before condemning a circuit. Battery, terminal, and alternator condition are unrelated to an excessive sleep current.

  144. Question 144Electrical and Electronic Systems

    After LED bulbs are installed in the turn-signal circuit, the signals flash rapidly. The most likely reason is:

    1. the flasher module has failed internally and must be replaced
    2. system voltage is too low at engine idle speed
    3. the LEDs draw less current than expected Correct answer.
    4. the bulbs were installed backwards in their sockets

    Explanation

    Many flashers and body-control-module routines sense lamp current to set flash rate and use the fast rate to warn of a burned-out bulb. LEDs draw far less current than the incandescent bulbs they replaced, so the module interprets the circuit as failed. A load resistor or a module recalibration is the usual fix.

  145. Question 145Electrical and Electronic Systems

    The preferred method for repairing a damaged wire in a harness is to:

    1. twist the strands together and wrap with tape
    2. leave the damaged section and reroute the harness
    3. crimp with an uninsulated butt connector
    4. solder the splice and seal it with heat-shrink Correct answer.

    Explanation

    A proper repair restores both the electrical path and the environmental protection of the wire. Soldering provides a low-resistance joint and adhesive-lined heat-shrink seals out moisture and supports the splice. A sealed crimp splice is also accepted, but bare tape and uninsulated connectors are not durable repairs.

  146. Question 146Electrical and Electronic Systems

    An alternator produces 14.1 volts DC but 1.6 volts of AC ripple at the battery, and the headlamps have a visible flicker. The most likely cause is:

    1. an open alternator field circuit
    2. a failed rectifier diode Correct answer.
    3. a slipping or glazed drive belt
    4. high resistance in the regulator ground

    Explanation

    The rectifier converts stator AC into DC, so a failed diode allows part of the AC waveform to reach the battery as ripple. Normal ripple is well under about half a volt AC; 1.6 volts with visible flicker points to an open or shorted diode. A slipping belt or open field circuit would reduce output rather than add ripple.

  147. Question 147Electrical and Electronic Systems

    A starter draws 200 amps and the ground cable drops 0.4 volt while cranking. What is the resistance of that cable?

    1. 0.0005 ohm
    2. 0.002 ohm Correct answer.
    3. 80 ohms
    4. 0.2 ohm

    Explanation

    Ohm's law gives resistance as voltage divided by current, so 0.4 volt divided by 200 amps equals 0.002 ohm. That small resistance is enough to dissipate 80 watts and reduce cranking speed. This is why voltage drop, not an ohmmeter, is used to evaluate high-current cables.

  148. Question 148Electrical and Electronic Systems

    Two 6-ohm resistors are wired in series, and that combination is connected in parallel with a 12-ohm resistor across a 12-volt source. Total current from the source is:

    1. 1 amp
    2. 3 amps
    3. 2 amps Correct answer.
    4. 0.5 amp

    Explanation

    The series pair adds to 12 ohms, which then sits in parallel with another 12 ohms, giving 6 ohms total. Dividing 12 volts by 6 ohms yields 2 amps from the source. The current splits evenly between the two parallel branches at 1 amp each.

  149. Question 149Electrical and Electronic Systems

    A technician back-probes a three-wire sensor with the key on. The reference wire reads 5.0 volts, the signal wire reads 4.9 volts, and the sensor ground wire reads 1.1 volts instead of near zero. The most likely fault is:

    1. a short from the signal wire to battery voltage
    2. a shorted sensor signal winding
    3. an open reference voltage circuit
    4. high resistance in the sensor ground circuit Correct answer.

    Explanation

    A sensor ground should sit within a few hundredths of a volt of chassis ground with the key on. A 1.1 volt reading means the return path has excessive resistance, which shifts the signal voltage the module sees and skews the reading. Reference voltage is present and correct, so the supply side is not the problem.

  150. Question 150Electrical and Electronic Systems

    A late-model vehicle has a 350 milliamp key-off draw that does not fall after the normal 30 to 45 minute sleep period. The most likely cause is:

    1. a slipping alternator belt
    2. an undercharged battery
    3. high-resistance battery cables
    4. a module that fails to go to sleep Correct answer.

    Explanation

    After the sleep delay, module current should drop to the normal 20 to 50 milliamp range; a persistent 350 milliamps indicates a module or its wake-up input is keeping the network active. Checking bus activity and performing a fuse-pull test will identify the responsible circuit. Charging-system and cable faults affect how the battery is charged, not how much current the vehicle draws at rest.

  151. Question 151Heating, Ventilation and Air Conditioning

    Which refrigerant is most commonly used in light-duty vehicle air conditioning systems built during the 2000s?

    1. R-410A
    2. R-12
    3. R-22
    4. R-134a Correct answer.

    Explanation

    R-134a replaced R-12 in automotive air conditioning during the mid-1990s because it does not deplete stratospheric ozone. R-22 and R-410A are stationary refrigeration and residential comfort-cooling refrigerants, not automotive ones.

  152. Question 152Heating, Ventilation and Air Conditioning

    What is the primary function of the condenser in an air conditioning system?

    1. Remove moisture from the refrigerant
    2. Absorb heat from the cabin air
    3. Release refrigerant heat to the outside air Correct answer.
    4. Control the flow of refrigerant into the evaporator

    Explanation

    The condenser receives high-pressure refrigerant vapor from the compressor and rejects its heat to the outside air so the refrigerant condenses into a liquid. Moisture removal is the job of the desiccant, and flow control is handled by the metering device.

  153. Question 153Heating, Ventilation and Air Conditioning

    A blower motor runs only on the highest speed setting. Which component is the most likely cause?

    1. The blower motor ground
    2. The HVAC control head
    3. The blower motor resistor Correct answer.
    4. The blower motor relay

    Explanation

    In a resistor-controlled blower circuit, the highest speed bypasses the resistor bank and runs the motor directly. If every lower speed is lost but high speed works, the resistor assembly is open.

  154. Question 154Heating, Ventilation and Air Conditioning

    A customer complains of weak airflow from all HVAC outlets along with a musty odor. Which is the most likely cause?

    1. A low refrigerant charge
    2. A failed blower motor relay
    3. A clogged cabin air filter Correct answer.
    4. A stuck-open blend door

    Explanation

    A restricted cabin air filter reduces airflow through every outlet and often traps debris that produces a musty smell. Refrigerant charge and blend door position affect temperature, not total airflow volume.

  155. Question 155Heating, Ventilation and Air Conditioning

    Refrigerant should be added to an air conditioning system by:

    1. Adding until the sight glass is clear
    2. Adding one can for each pound of capacity
    3. Weighing the charge to the specified amount Correct answer.
    4. Adding until the gauges show the desired pressures

    Explanation

    The only accurate method is to weigh the refrigerant into the system using a recovery/recycling machine and the manufacturer's specified charge. Gauge pressures and sight glass appearance vary with temperature and cannot establish a precise charge.

  156. Question 156Heating, Ventilation and Air Conditioning

    Water that collects on the evaporator case normally leaves the vehicle through the:

    1. Heater core outlet
    2. Blower motor cooling tube
    3. Evaporator drain tube Correct answer.
    4. Condensate return line to the compressor

    Explanation

    Condensate that forms on the cold evaporator collects in the case and drains to the outside through a hose on the firewall or floor. A plugged drain leaves water in the case, which can soak the carpet and cause odors.

  157. Question 157Heating, Ventilation and Air Conditioning

    Engine coolant flows through which component to warm the air entering the passenger compartment?

    1. The heater core Correct answer.
    2. The evaporator
    3. The accumulator
    4. The condenser

    Explanation

    The heater core is a small radiator inside the HVAC case that uses hot engine coolant to warm air passing over its fins. The evaporator and condenser are part of the refrigerant circuit and do not carry coolant.

  158. Question 158Heating, Ventilation and Air Conditioning

    Which tool pinpoints a refrigerant leak by sensing refrigerant vapor in the air?

    1. A handheld infrared thermometer
    2. An electronic leak detector Correct answer.
    3. A manifold gauge set
    4. A vacuum pump

    Explanation

    An electronic leak detector uses a heated sensor that reacts to halogenated refrigerant vapor and produces an audible or visual alarm near the leak. Gauges and vacuum pumps show system condition but cannot locate a leak.

  159. Question 159Heating, Ventilation and Air Conditioning

    On a system that uses an orifice tube and a cycling clutch, the compressor clutch is cycled by:

    1. The blower motor resistor
    2. The high-pressure relief valve
    3. The engine coolant sensor
    4. The low-pressure cycling switch Correct answer.

    Explanation

    In a cycling-clutch orifice-tube system, a pressure switch on the low side opens when suction pressure drops and closes when it rises, engaging and disengaging the clutch to control evaporator temperature. The relief valve is a safety device and does not cycle the clutch.

  160. Question 160Heating, Ventilation and Air Conditioning

    The high-pressure switch opens to protect the system when:

    1. Compressor clutch current exceeds a set limit
    2. Suction pressure exceeds a set limit
    3. Discharge pressure rises above a set limit Correct answer.
    4. Refrigerant charge falls below a set level

    Explanation

    The high-pressure switch is connected to the discharge side and opens the clutch circuit when head pressure climbs too high, preventing hose or compressor damage. Suction-side control is handled by a different switch or the compressor control valve.

  161. Question 161Heating, Ventilation and Air Conditioning

    Which component meters refrigerant flow into the evaporator in a cycling-clutch orifice-tube system?

    1. The accumulator
    2. The expansion valve
    3. The receiver-drier
    4. The orifice tube Correct answer.

    Explanation

    A fixed orifice tube restricts flow and creates the pressure drop that allows the evaporator to absorb heat. Expansion valves and receiver-driers belong to thermostatic expansion valve systems instead.

  162. Question 162Heating, Ventilation and Air Conditioning

    In an orifice-tube system, the accumulator is located between the:

    1. Receiver-drier and the expansion valve
    2. Compressor outlet and the condenser inlet
    3. Evaporator outlet and compressor inlet Correct answer.
    4. Condenser outlet and the orifice tube

    Explanation

    The accumulator sits on the low side, after the evaporator, so it can store any liquid refrigerant that did not boil off and release it gradually while the compressor draws vapor. It also holds the desiccant that removes moisture.

  163. Question 163Heating, Ventilation and Air Conditioning

    Which component stores liquid refrigerant and removes moisture in a system that uses an expansion valve?

    1. The receiver-drier Correct answer.
    2. The accumulator
    3. The orifice tube
    4. The suction hose

    Explanation

    In an expansion-valve system the receiver-drier is mounted on the high side after the condenser, where it holds liquid refrigerant and passes it through desiccant to remove moisture. Accumulators serve the same drying purpose in orifice-tube systems.

  164. Question 164Heating, Ventilation and Air Conditioning

    A/C pressures are normal and the evaporator outlet is cold, but the vent temperature stays warm in every setting. Which is the most likely cause?

    1. The compressor clutch is slipping
    2. The condenser fan is inoperative
    3. The system is overcharged with refrigerant
    4. The blend door is stuck in the hot position Correct answer.

    Explanation

    If the evaporator is cold and pressures are correct, the refrigeration circuit is working; the cold air is simply being mixed with heater core air before it leaves the case. A blend door stuck toward hot produces exactly this pattern.

  165. Question 165Heating, Ventilation and Air Conditioning

    A vehicle's A/C cools well at highway speed but poorly when stopped in traffic. Which is the most likely cause?

    1. A restricted orifice tube
    2. Poor condenser airflow Correct answer.
    3. An undercharged system
    4. A clogged cabin air filter

    Explanation

    At highway speed ram air carries heat away from the condenser, but at a standstill the system depends on the electric fan. A fan that does not run, or a condenser blocked with debris, causes cooling to fade whenever the vehicle stops.

  166. Question 166Heating, Ventilation and Air Conditioning

    The compressor clutch does not engage and the refrigerant charge is correct. Which of these could still prevent engagement?

    1. A failed blower motor
    2. A clogged cabin air filter
    3. An open clutch coil circuit Correct answer.
    4. A restricted condenser

    Explanation

    The clutch engages only when the coil is energized, so an open coil winding, bad ground, or broken feed wire keeps it disengaged even with a full charge. The other choices affect cooling performance but do not control clutch electrical operation.

  167. Question 167Heating, Ventilation and Air Conditioning

    Why must an A/C system be evacuated before it is charged?

    1. To test the compressor clutch circuit
    2. To increase the refrigerant charge weight
    3. To flush oil from the evaporator
    4. To remove moisture and non-condensable gases Correct answer.

    Explanation

    Pulling a deep vacuum boils off trapped moisture and removes air, which otherwise raises head pressure and forms acids with refrigerant. Vacuum does not remove refrigerant oil, which must stay in the system to lubricate the compressor.

  168. Question 168Heating, Ventilation and Air Conditioning

    R-134a service ports are designed so that:

    1. A standard tire chuck will fit the ports
    2. Only the low side can be accessed
    3. The high and low side ports are different sizes Correct answer.
    4. Both ports are the same size and interchangeable

    Explanation

    R-134a systems use quick-disconnect service ports with different diameters for high and low sides so the charging equipment cannot be connected to the wrong side. The design also helps prevent cross-contamination with other refrigerants.

  169. Question 169Heating, Ventilation and Air Conditioning

    Mixing mineral oil into an R-134a system is a problem because mineral oil:

    1. Corrodes aluminum components
    2. Does not circulate with R-134a Correct answer.
    3. Boils at normal operating temperature
    4. Solidifies inside the condenser

    Explanation

    Mineral oil has no affinity for R-134a and will not be carried through the circuit, so it collects in the compressor sump and leaves the rest of the system unlubricated. PAG oil is used because it migrates with R-134a.

  170. Question 170Heating, Ventilation and Air Conditioning

    A vehicle has little heat at idle but good heat at higher engine speeds. Which is the most likely cause?

    1. A failed blower motor resistor
    2. A restricted heater core Correct answer.
    3. A misadjusted mode door
    4. A faulty coolant temperature sensor

    Explanation

    Coolant flow through the heater core rises with engine speed, so a partially plugged core or a low coolant level delivers heat only when pump output increases. A mode door or blower fault would not change with engine speed.

  171. Question 171Heating, Ventilation and Air Conditioning

    A variable-displacement compressor maintains a constant evaporator pressure by:

    1. Varying piston stroke via a control valve Correct answer.
    2. Changing the system charge
    3. Bypassing the condenser coil
    4. Cycling the clutch rapidly on and off

    Explanation

    A control valve responds to suction pressure and changes crankcase pressure inside the compressor, which alters piston stroke and therefore refrigerant flow. This lets the compressor run continuously while matching output to demand.

  172. Question 172Heating, Ventilation and Air Conditioning

    Both gauge pressures read higher than specification and the condenser is clean with the fan working. Which is the most likely cause?

    1. A plugged orifice tube
    2. An overcharged system Correct answer.
    3. A slipping compressor belt
    4. A low refrigerant charge

    Explanation

    Excess liquid refrigerant raises head pressure and, with it, suction pressure, because the condenser cannot condense more than the system was designed to handle. A restricted metering device or low charge would lower suction pressure instead.

  173. Question 173Heating, Ventilation and Air Conditioning

    A system with an expansion valve that is stuck closed will typically show:

    1. High suction and high discharge pressure
    2. Low suction pressure and little or no cooling Correct answer.
    3. Normal pressures with poor airflow
    4. High suction pressure with a flooded evaporator

    Explanation

    With no refrigerant passing the valve, the compressor evacuates the low side, so suction pressure drops well below normal and almost no heat is absorbed. Head pressure also tends to fall because the condenser receives little refrigerant to condense.

  174. Question 174Heating, Ventilation and Air Conditioning

    Cooling stops after a few minutes of operation and returns after the system is shut off for a while, and ice forms at the metering device. Which is the most likely cause?

    1. A faulty blower motor resistor
    2. An overcharge of refrigerant
    3. Moisture in the system Correct answer.
    4. A restricted condenser

    Explanation

    Water in the system can freeze at the metering device where refrigerant temperature drops, blocking flow until the ice melts after shutdown. The cycle then repeats, which is the classic symptom of moisture contamination.

  175. Question 175Heating, Ventilation and Air Conditioning

    When a condenser is replaced, the technician should:

    1. Install it without adding any oil
    2. Flush the evaporator with water
    3. Add the specified amount of new PAG oil Correct answer.
    4. Reuse the old O-rings after cleaning

    Explanation

    A significant portion of the system oil is trapped in the old condenser, so the replacement must be compensated with the amount of new oil specified for that component. Reusing old seals or introducing water into the circuit risks leaks and contamination.

  176. Question 176Engine Performance

    A scan tool shows diagnostic trouble code P0300 stored in a powertrain control module. What does this code indicate?

    1. Random or multiple cylinder misfire Correct answer.
    2. Catalyst efficiency below threshold
    3. An evaporative emission leak
    4. A lean fuel mixture on bank 1

    Explanation

    P0300 is the generic code for a misfire that the PCM cannot attribute to one specific cylinder. Codes P0301 through P0308 identify individual cylinders, while P0420 covers catalyst efficiency and P0455 covers evaporative leaks.

  177. Question 177Engine Performance

    Which sensor reports the oxygen content of the exhaust stream back to the powertrain control module?

    1. Mass airflow sensor
    2. Throttle position sensor
    3. Manifold absolute pressure sensor
    4. Heated oxygen sensor Correct answer.

    Explanation

    The oxygen sensor generates a voltage or current signal that reflects how much oxygen remains in the exhaust, allowing the PCM to judge whether the mixture is rich or lean. Airflow, manifold pressure, and throttle angle are intake-side inputs, not exhaust gas measurements.

  178. Question 178Engine Performance

    What is the primary job of the positive crankcase ventilation system?

    1. To reduce the operating temperature of the engine coolant
    2. To increase intake air velocity at low engine speed
    3. To add extra fuel during cold engine starting
    4. To pull crankcase vapors into the intake Correct answer.

    Explanation

    The PCV system uses intake manifold vacuum to draw blowby gases and oil vapor out of the crankcase and into the intake so they are burned in the cylinders. This prevents crankcase pressure from building and keeps hydrocarbons out of the atmosphere.

  179. Question 179Engine Performance

    Under what condition does the powertrain control module command the malfunction indicator lamp on?

    1. The ignition switch is turned to the start position
    2. A two-trip emissions fault is confirmed Correct answer.
    3. Fuel pressure drops briefly under acceleration
    4. Any sensor is disconnected during a road test

    Explanation

    For most emissions-related faults the PCM must see the failure on two consecutive trips before it illuminates the MIL, which prevents false illumination from a momentary glitch. Illumination at key-on is only a bulb check, not a response to a fault.

  180. Question 180Engine Performance

    The stoichiometric air-fuel ratio by mass for gasoline is approximately:

    1. 9.8 to 1
    2. 14.7 to 1 Correct answer.
    3. 6.5 to 1
    4. 18.2 to 1

    Explanation

    Gasoline burns completely at about 14.7 parts air to 1 part fuel by mass, which is the ratio closed-loop fuel control drives toward. Ratios well below that value are rich and ratios well above it are lean.

  181. Question 181Engine Performance

    What is the purpose of the thermostat in the engine cooling system?

    1. To release pressure from the cooling system
    2. To control minimum operating temperature Correct answer.
    3. To circulate coolant through the radiator
    4. To switch the electric cooling fan on and off

    Explanation

    The thermostat stays closed while the engine warms and then opens at its rated temperature, holding coolant in the block so the engine reaches and maintains its designed operating temperature. It does not pump coolant, control the fan, or regulate system pressure.

  182. Question 182Engine Performance

    The manifold absolute pressure sensor provides the PCM with information about:

    1. The temperature of the intake air charge
    2. Pressure inside the intake manifold Correct answer.
    3. The amount of fuel returning to the tank
    4. The volume of air entering the engine

    Explanation

    The MAP sensor converts intake manifold pressure into a voltage signal that the PCM uses with rpm to calculate airflow and load. Manifold pressure drops as vacuum rises, so the signal also indicates throttle position and engine load.

  183. Question 183Engine Performance

    In a speed-density fuel injection system, which two inputs are most important for calculating base injector pulse width?

    1. Manifold pressure and engine rpm Correct answer.
    2. Steering wheel angle and vehicle speed
    3. Fuel tank pressure and canister purge flow
    4. A/C refrigerant pressure and ambient light

    Explanation

    Speed-density systems estimate cylinder air charge from manifold absolute pressure and engine speed, then compute the fuel mass needed for the target ratio. Other sensors only trim that base calculation.

  184. Question 184Engine Performance

    Long-term fuel trim on bank 1 reads about +18 percent at idle and returns to near 0 percent at 2500 rpm. The most likely cause is:

    1. Leaking fuel injectors on bank 1
    2. A restricted fuel filter or weak pump
    3. A vacuum leak at the intake manifold Correct answer.
    4. A failed oxygen sensor heater circuit

    Explanation

    A vacuum leak adds unmetered air that is proportionally larger at low airflow, so the PCM must add fuel at idle but needs little correction at higher rpm. A fuel supply restriction or weak pump behaves the opposite way, growing worse as demand rises.

  185. Question 185Engine Performance

    A cylinder 3 misfire code is stored. The technician moves the ignition coil from cylinder 3 to cylinder 5, clears codes, and the misfire now sets on cylinder 5. This result indicates:

    1. An injector circuit problem
    2. A faulty ignition coil Correct answer.
    3. A mechanical fault in cylinder 3
    4. A faulty spark plug in cylinder 3

    Explanation

    When a misfire follows the part that was moved, the part itself is the cause. If the misfire had stayed on cylinder 3, the fault would lie with that cylinder's plug, injector, or mechanical condition.

  186. Question 186Engine Performance

    Which symptom is most likely when an EGR valve is stuck partially open at all times?

    1. Hard starting when hot
    2. Pinging under heavy load
    3. Reduced NOx at cruise
    4. Rough idle and stalling Correct answer.

    Explanation

    Exhaust gas flowing at idle severely dilutes the intake charge when airflow is already low, producing rough running, surge, and stalling. At cruise the same flow may be tolerable because airflow is much higher.

  187. Question 187Engine Performance

    A vehicle sets P0420, catalyst efficiency below threshold on bank 1. Which of these is a common cause?

    1. An oxygen sensor heater circuit failure
    2. A vacuum leak at the intake gasket
    3. A stuck-closed EGR valve at cruise
    4. A worn-out catalytic converter Correct answer.

    Explanation

    The catalyst monitor compares the switching activity of the downstream oxygen sensor with the upstream sensor; when the converter loses its oxygen storage capacity, the downstream signal begins switching in step with the upstream, setting P0420. Age, contamination from coolant or oil, and misfire damage are typical causes.

  188. Question 188Engine Performance

    A coolant temperature sensor reads 60 degrees higher than actual on a cold start. The PCM will most likely:

    1. Command a leaner mixture Correct answer.
    2. Delay closed-loop operation
    3. Disable the fuel pump relay
    4. Increase idle speed to 1500 rpm

    Explanation

    The PCM uses coolant temperature to set cold-start enrichment; if the sensor reports a warm engine, the PCM assumes less fuel is needed and delivers a leaner mixture. The result is often a hard cold start or a cold stumble.

  189. Question 189Engine Performance

    An injector balance test shows that one injector produces noticeably less pressure drop than the others on the same rail. That injector is:

    1. Leaking internally at the nozzle
    2. Electrically open at the coil
    3. Stuck wide open
    4. Restricted or clogged Correct answer.

    Explanation

    The balance test pulses each injector for a fixed time and measures how far rail pressure falls; less drop means less fuel flowed, which points to a restricted nozzle or filter screen. A leaking or stuck-open injector would produce a larger drop than the others.

  190. Question 190Engine Performance

    A compression test on a warm engine shows all cylinders at about 120 psi dry. Adding a small amount of oil raises every cylinder to about 155 psi. This result suggests:

    1. A blown head gasket
    2. Bent connecting rods
    3. Worn piston rings Correct answer.
    4. Leaking intake valves

    Explanation

    Oil temporarily seals the ring-to-cylinder gap, so a large increase after oiling points to ring or cylinder wall wear as the source of leakage. Leaking valves or a head gasket would not improve substantially because the oil does not reach those leak paths.

  191. Question 191Engine Performance

    A vacuum gauge on a steady-idle engine reads a steady 10 in-Hg where 18 to 22 in-Hg is expected. The most likely cause is:

    1. A large vacuum leak Correct answer.
    2. Late ignition timing at idle
    3. A weak valve spring on one cylinder
    4. A restricted exhaust system

    Explanation

    A steady but uniformly low reading indicates the engine cannot develop normal manifold vacuum, typically because unmetered air is entering or the throttle is open further than normal. A restricted exhaust usually shows a normal reading that slowly drops as rpm is held.

  192. Question 192Engine Performance

    An EVAP system smoke test shows smoke escaping from around the fuel filler cap. The correct repair is to:

    1. Replace the canister purge valve
    2. Replace the vent solenoid
    3. Replace the filler cap seal Correct answer.
    4. Replace the fuel tank pressure sensor

    Explanation

    Smoke exiting at the cap identifies the cap seal as the leak path, so resealing or replacing the cap addresses the fault. Other components are replaced only when smoke or a functional test shows they leak or fail to seal.

  193. Question 193Engine Performance

    At a steady cruise, short-term fuel trim is +22 percent and long-term fuel trim is +15 percent. What does this combined trim indicate?

    1. Holding trim at zero because values are normal
    2. Turning off closed-loop fuel control
    3. Removing fuel to correct a rich condition
    4. Adding fuel to correct a lean condition Correct answer.

    Explanation

    Total fuel trim is the sum of short-term and long-term corrections, here about +37 percent, which means the PCM is lengthening injector pulse width to compensate for a lean mixture. Positive trim always adds fuel; negative trim subtracts it.

  194. Question 194Engine Performance

    What is the purpose of the heater circuit built into a heated oxygen sensor?

    1. To reduce current draw on the fuel pump circuit
    2. To keep the sensor below its switching point
    3. To bring the sensor up to temperature quickly Correct answer.
    4. To warm the exhaust gas ahead of the catalyst

    Explanation

    A zirconia oxygen sensor must reach several hundred degrees before it produces a usable signal, and the internal heater achieves this shortly after start-up so the system can enter closed loop sooner. Exhaust heat alone would take much longer, especially at idle.

  195. Question 195Engine Performance

    An engine with a timing chain sets P0016, crankshaft and camshaft position correlation. This code most often indicates:

    1. A stretched timing chain Correct answer.
    2. A faulty knock sensor
    3. A stuck-open thermostat
    4. Low fuel pressure at the rail

    Explanation

    P0016 is set when the PCM compares the crankshaft and camshaft signals and finds the relationship outside the acceptable window. A stretched chain, jumped tooth, or faulty phaser changes that relationship and is the usual mechanical cause.

  196. Question 196Engine Performance

    At warm idle, a scan tool shows STFT +3 percent, LTFT +25 percent, MAP at 9 in-Hg where 18 to 22 in-Hg is specified, and the oxygen sensor switching normally. Which fault best fits these readings?

    1. A weak fuel pump
    2. A leaking fuel injector
    3. A restricted fuel filter
    4. An intake vacuum leak Correct answer.

    Explanation

    Low manifold vacuum plus a large positive long-term trim that the short-term trim is not currently fighting is the classic signature of unmetered air entering the intake. The normal oxygen sensor activity confirms the sensor is responding to the lean mixture rather than being faulty.

  197. Question 197Engine Performance

    A cylinder leak-down test on cylinder 2 shows 35 percent leakage with air escaping from the radiator filler neck. The cause is:

    1. A failed head gasket Correct answer.
    2. A burned exhaust valve
    3. A collapsed lifter
    4. Worn piston rings

    Explanation

    Air reaching the cooling system can only travel there through a breach between the combustion chamber and a coolant passage, which points to the head gasket, a cracked head, or a cracked block. Valve and ring leakage escape through the intake, exhaust, or crankcase instead.

  198. Question 198Engine Performance

    An engine cranks with good compression and correct fuel pressure but will not start. While cranking, the scan tool shows 0 rpm and there is no injector pulse. Which component should be tested first?

    1. The crankshaft position sensor Correct answer.
    2. The camshaft position sensor
    3. The fuel pump relay
    4. The ignition coil primary circuit

    Explanation

    The PCM derives engine speed from the crankshaft position signal; with no rpm shown during cranking, it will not schedule spark or injector pulses. A failed crank sensor or its wiring therefore explains both the missing tach signal and the absence of injector pulse.

  199. Question 199Engine Performance

    A wideband oxygen sensor reports a lambda value of 0.85 during closed-loop operation. This reading means the exhaust mixture is:

    1. High in oxygen content
    2. Rich of stoichiometry Correct answer.
    3. Lean of stoichiometry
    4. Exactly at stoichiometry

    Explanation

    Lambda is the actual air-fuel ratio divided by the stoichiometric ratio, so a value below 1.0 means there is less air than needed for complete combustion, which is a rich mixture. Values above 1.0 indicate excess air and a lean condition.

  200. Question 200Engine Performance

    Which condition will normally prevent the EVAP monitor from running on a typical late-model vehicle?

    1. A fuel level above 85 percent Correct answer.
    2. Battery voltage held at 14.5 volts
    3. Manifold vacuum above 15 in-Hg
    4. Intake air temperature below 40 degrees F

    Explanation

    The EVAP monitor needs expansion volume in the tank to pressurize or draw a vacuum, so most strategies block the monitor when the tank is more than about 85 percent full or nearly empty. Normal charging voltage and adequate manifold vacuum are conditions that allow monitors to run rather than block them.

ASE G1 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Stoichiometric air-fuel ratio
For gasoline, stoichiometric is about 14.7 parts air to 1 part fuel by mass, producing complete combustion under ideal conditions.
Cylinder leak-down test
Compressed air is applied to a cylinder at top dead center; leakage heard at the intake, exhaust, or oil filler identifies valve or ring sealing problems.
PCV valve function
The positive crankcase ventilation valve meters crankcase vapors into the intake manifold so pressure does not build and oil seals are not forced to leak.
Thermostat opening temperature
A coolant thermostat begins opening near its rated temperature, commonly 180 to 195 degrees Fahrenheit, and reaches full opening slightly above that rating.
Torque converter stator
The stator redirects fluid flow between the turbine and impeller at low speed, multiplying engine torque until turbine speed approaches impeller speed.
Transmission limp mode
When the control module detects a serious fault, it may default to a fixed gear or reduced shift schedule to protect the transmission and allow limited driving.
CVT belt and pulleys
A continuously variable transmission changes ratio by moving a steel belt or chain between variable-diameter pulleys, providing stepless acceleration and requiring specific fluid.
Transmission fluid level check
Most automatic transmissions are checked with the engine running and fluid warm; some use a dipstick, while others use an overflow plug at a specified temperature.
Clutch pedal free play
Free play is the clearance before the release bearing contacts the pressure plate; too little clearance can cause clutch slip and release bearing wear.
CV joint click diagnosis
A rhythmic click during turns usually indicates a worn outer constant-velocity joint, while vibration during acceleration often points to an inner joint.
Differential backlash measurement
Ring and pinion backlash is measured with a dial indicator against a tooth while holding the pinion stationary, then compared with the manufacturer's specification.
Limited-slip friction modifier
Many clutch-type limited-slip differentials require a friction modifier added to the gear oil to prevent chatter during low-speed turns.
Caster angle effect
Positive caster tilts the steering axis rearward at the top, improving straight-line stability and steering return; excessive caster increases steering effort.
Camber angle definition
Camber is the inward or outward tilt of the tire's top relative to vertical; negative camber tilts the top inward and affects cornering grip and tire wear.
Toe setting definition
Toe is the difference in track width measured at the front and rear of the tires; toe-in means the fronts are closer together than the rears.
Wheel bearing noise test
A worn wheel bearing often produces a hum that changes when vehicle weight shifts side to side; loading the suspect side usually increases the noise.
Brake fluid hygroscopic property
Glycol-based brake fluid absorbs moisture from the air, which lowers its boiling point and can cause pedal fade under repeated heavy braking.
Rotor minimum thickness
Disc brake rotors have a minimum thickness stamped or cast on the hub; machining or wear below that dimension requires rotor replacement.
Brake pedal pulsation cause
Pedal pulsation during braking is commonly caused by rotor thickness variation or lateral runout, which changes caliper piston travel as the wheel rotates.
ABS warning lamp meaning
An illuminated ABS warning lamp indicates the antilock system is disabled, but conventional hydraulic brakes normally remain functional; wheel speed sensors are common causes.
Ohm's law formula
Ohm's law states voltage equals current multiplied by resistance, written V equals I times R; it is used to calculate expected values in electrical circuits.
Parasitic draw measurement
Parasitic draw is measured with an ammeter in series after modules sleep; excessive draw drains the battery and is commonly specified below about 50 milliamps.
CAN bus termination resistance
A healthy CAN bus typically shows about 60 ohms across the communication lines because two 120-ohm terminating resistors are connected in parallel.
Voltage drop test purpose
A voltage drop test measures loss across a circuit under load; excessive drop indicates high resistance at connections, cables, switches, or ground points.
Refrigerant recovery requirement
Refrigerant must be recovered with approved equipment and not vented to the atmosphere; recycling and charging amounts are measured by weight.
A/C low-side pressure
With the compressor engaged, low-side pressure commonly reads about 25 to 45 psi, varying with ambient temperature, humidity, and system design.
Blend door actuator function
The blend door actuator moves a flap that directs air through or around the heater core, controlling outlet temperature; clicking often indicates stripped actuator gears.
Heater core no-heat cause
No cabin heat can result from low coolant, a stuck-open thermostat, a failed blend door, or a blocked heater core; coolant flow and door travel must be verified.
Fuel trim positive value
Positive fuel trim means the control module is adding fuel to compensate for a lean condition, often caused by vacuum leaks or low fuel pressure.
Upstream oxygen sensor signal
A properly switching upstream oxygen sensor oscillates between about 0.1 and 0.9 volt, allowing the control module to adjust fuel mixture.
Misfire detection method
The misfire monitor compares crankshaft speed fluctuations for each cylinder; a misfire slows crankshaft acceleration and can set a diagnostic trouble code.
Evaporative large leak code
A large evaporative emission leak code such as P0455 indicates a major leak, often from a loose fuel cap, disconnected hose, or failed purge valve.

ASE G1 study guide

Engine Systems

What this domain actually tests

G1 engine work is inspection and service, not overhaul. You must know the lubrication path (pickup, pump, filter, galleries, drain-back), the cooling path (water pump, thermostat, radiator, hoses, pressure cap, fan, recovery bottle), the induction path (air filter, duct, throttle body, PCV/breather), and the accessory drive (serpentine belt, tensioner, idlers, mounts, seals).

Concepts you must own

  • Oil grade: the first number describes cold flow (lower = thinner when cold), the second describes viscosity at operating temperature. Follow the cap or service manual, not habit.
  • A red oil-can lamp indicates low oil pressure; an amber one indicates low oil level. Different sensors, different response.
  • Coolant is mixed 50/50 unless specified; fill and burp a cold engine with the heater on full hot to open the blend door.
  • Thermostats fail open (slow warm-up, weak heat) or closed (overheat).
  • Stretch-fit belts and serpentine routing: record the routing before removal.

Traps

Questions often dress a simple fault in a customer complaint. Overheating with a cold lower radiator hose points to the thermostat, not the water pump. A cold-start chirp that fades is usually a worn belt or tensioner, not an internal bearing. Blue smoke on startup after sitting is valve guides or seals, not piston rings. Also watch for oil consumption confused with an oil leak.

Worked example

An engine stores P0128 (coolant temperature below regulating temperature). Watch live ECT data on a road test: if temperature climbs slowly and never reaches roughly 90 C / 195 F, the thermostat is hanging open. Replace the thermostat and coolant, then verify on a drive, not at idle.

Rule of thumb

Service oil and coolant at the severe-service interval, not the longest interval printed in the manual.

Automatic Transmission and Transaxle

Scope

On the G1 you check condition and fluid, perform routine services, and recognize symptoms that condemn a unit. Know the major parts: torque converter with its clutch, pump, valve body, shift solenoids, clutch packs, planetary gearsets, final drive (transaxle), TCM, cooler lines, mounts. Understand that a transaxle carries differential fluid shared with or separate from the transmission fluid depending on design.

Concepts you must own

  • Fluid is not universal. CVT fluid, dual-clutch fluid, and step-gear ATF are different products; the wrong fluid can destroy a unit in miles.
  • Level check procedure varies. Most conventional automatics: level ground, engine idling, parking brake set, shift through the ranges, then check in Park or Neutral as the manufacturer specifies at operating temperature.
  • Filters and pan gaskets: some units use a serviceable pan filter, others a spin-on or a screen that is not a maintenance item.
  • Adaptive learning: after service or repair, a scan tool relearn may be required to restore shift quality.
  • Cooler line flush versus drain and fill: a drain and fill exchanges only part of the fluid.

Traps

Check level with the engine off on an idling-check unit and you will overfill or underfill. "Lifetime fluid" claims in advertising do not override severe-service intervals. A shudder under light torque converter clutch apply can be fluid-related rather than a failed converter; a delayed engagement from cold often means low or aerated fluid. Do not confuse a transfer case or power take-off unit on an AWD vehicle with the transaxle.

Worked example

A customer reports a flare on the 2-3 shift. Check fluid level and condition first using the correct procedure. Dark fluid with a burnt odor and clutch material in the pan means the unit has been overheated and internal repair is likely. Clean, correct-level fluid with a flare points toward a solenoid, valve body, or adaptive issue; scan for codes and check for a relearn.

Rule of thumb

Smell and color tell you more than mileage: burnt smell plus dark fluid means the unit has been hot.

Manual Drive Train and Axles

Scope

This domain covers the clutch and its hydraulics, manual transaxles and transmissions, CV axles and boots, driveshafts and universal joints, differentials, transfer cases, and wheel-end components. The G1 expects inspection and service competence plus the ability to link a noise or vibration to a specific component.

Concepts you must own

  • Clutch release systems: cable, hydraulic master and slave, and the concentric release bearing. A soft or sinking pedal with no external leak often means a failed master or slave.
  • Manual gearboxes may use gear oil or, in some designs, automatic transmission fluid; use what the manufacturer specifies.
  • CV joints: an outer joint clicks or pops on turns under load; an inner joint can cause a shudder or vibration under acceleration. A torn boot throws grease and eventually destroys the joint.
  • Universal joints and center bearings cause vibration that changes with vehicle speed and load; a seized joint may chirp in reverse.
  • Differentials: hypoid gear oil plus friction modifier for limited-slip units, or a dedicated LSD lubricant.
  • Axle seals, vents, and pinion seals: a plugged vent pushes oil past good seals.

Traps

Do not diagnose a whine by sound alone. A gear whine tracks throttle and coast; a bearing noise usually tracks speed and often changes in turns. Caster and camber wear can imitate a driveline vibration. Limited-slip chatter on tight turns is normal until the friction modifier is correct. Never substitute ATF for gear oil unless the manufacturer calls for it.

Worked example

A front-wheel-drive car clicks rhythmically while turning right at low speed. The loaded side is the left outer CV joint. Inspect the boot for a tear and grease loss, then replace the halfshaft or joint and recheck the alignment if the strut was disturbed.

Rule of thumb

Fill a manual gearbox or differential until lubricant just reaches the fill plug hole on a level surface.

Suspension and Steering

Scope

The G1 tests inspection and replacement of worn parts plus a working understanding of alignment angles. Know struts and shocks, coil and leaf springs, control arms and bushings, ball joints, tie rods, sway bar links, steering racks, electric power steering, and hub bearings.

Concepts you must own

  • Camber: the inward or outward tilt of the wheel viewed from the front. Too much negative camber wears the inner edge of the tire.
  • Caster: the forward or rearward tilt of the steering axis. More positive caster improves high-speed stability and returnability.
  • Toe: wheels pointing in or out relative to each other. Incorrect toe produces rapid, feathered edge wear.
  • Play checks: a ball joint shows vertical play with the wheel grabbed at 12 and 6 o'clock; a tie rod end shows side play at 3 and 9.
  • Hub bearings: a bad bearing often changes tone when the vehicle is loaded in a turn.
  • Power steering: hydraulic systems need the specified fluid; electric systems have no fluid and may need a steering angle sensor reset after alignment.

Traps

Pulling is not automatically an alignment problem. Swap the front tires side to side first to rule out a radial tire pull. A vehicle that pulls only while braking is a brake fault, not alignment. Conical or feathered wear patterns each point at different angles. Do not condemn a strut for a noise that comes from a sway bar link.

Worked example

A vehicle leads to the right and the right front tire shows inner edge wear. Camber is likely too negative on that side or caster is unequal. Measure and adjust to specification, then verify with a road test on a level crown-free road.

Rule of thumb

Pull usually follows the side with less positive caster or more positive camber; tire swap comes first.

Brakes

Scope

Brake work on the G1 covers inspection, pad and rotor replacement, caliper service, hose and line condition, drum brakes, parking brakes, ABS components, and hydraulic diagnosis. Safety and cleanliness matter as much as diagnosis.

Concepts you must own

  • Fluids: DOT 3, DOT 4, and DOT 5.1 are glycol-based and hygroscopic. DOT 5 is silicone and must never be mixed with glycol fluid. Follow the cap.
  • Rotor service: measure thickness with a micrometer and compare to the minimum stamped on the rotor. Below minimum means replacement, not resurfacing.
  • Caliper service: clean and lubricate slide pins, inspect the piston boot, and support the caliper so the hose is not stretched.
  • Pedal diagnosis: a low or spongy pedal suggests air, a leaking component, or rear drum adjustment; a hard pedal suggests a booster or check valve fault.
  • Bleeding order follows the manufacturer, typically starting at the wheel farthest from the master cylinder.
  • ABS: a wheel speed sensor fault can disable ABS and set a brake warning lamp without any base brake symptom.

Traps

Do not let a caliper hang by its hose. Do not push a dirty piston back without considering the ABS hydraulic unit; opening the bleeder can prevent forcing contaminated fluid upstream. A pull under braking is usually a sticking caliper or a collapsed hose, not an alignment fault. Pad squeal at low speed may be normal for a given friction material; metal-on-metal grinding is not.

Worked example

A vehicle pulls left only when the brakes are applied and the right front wheel is hot after a short drive. A sticking right caliper is dragging. Inspect the slide pins and piston, replace or rebuild as needed, then flush fluid and road test.

Rule of thumb

If measured rotor thickness is at or below the stamped minimum, replace the rotor.

Electrical and Electronic Systems

Scope

Expect battery, starting, and charging service plus basic circuit diagnosis with a digital multimeter. You should be comfortable with Ohm's law, series and parallel circuits, fuses and relays, grounds, voltage drop testing, parasitic draw, and module communication basics.

Concepts you must own

  • Open-circuit voltage: about 12.6 V is a fully charged battery, 12.4 V roughly 75 percent, 12.2 V about 50 percent, 12.0 V about 25 percent, measured after removing surface charge.
  • Charging: a healthy alternator holds roughly 13.5 to 14.5 V at the battery with loads on.
  • Voltage drop beats resistance testing for high-current circuits. Measure from end to end under load; typically allow about 0.1 V per connection and around 0.5 V total on the insulated circuit.
  • Grounds cause more strange faults than any other single item: lights that ground through another bulb, modules that reset, intermittent no-cranks.
  • Parasitic draw: allow modules to sleep, latch doors, and use an amp clamp rather than breaking the circuit with a meter on a module-heavy vehicle.
  • Wire repair: solder and heat-shrink or a proper crimp; never twist and tape in a harness.

Traps

A battery that reads 12.0 V is not necessarily bad, it may simply be discharged; charge and retest before condemning it. Resistance checks on a meter tell you little about a circuit that fails only under load. Do not probe module connectors carelessly. A no-crank with bright headlights points at the starter circuit, not the battery.

Worked example

A slow crank with 12.5 V at the battery posts but 10.9 V at the starter terminal during crank indicates excessive voltage drop on the positive cable. Measure from battery positive to starter stud while cranking; more than about 0.5 V condemns the cable or connections.

Rule of thumb

Test voltage drop under load; test the battery after charging, never right after shutdown.

Heating, Ventilation, and Air Conditioning

Scope

The G1 covers A/C inspection and routine service, heater performance, and air distribution. You must know the refrigerant circuit: compressor, condenser, receiver-drier or accumulator, expansion device, evaporator, and the controls that move air.

Concepts you must own

  • Refrigerants: R-134a and R-1234yf are not interchangeable. R-1234yf is mildly flammable and needs dedicated recovery equipment and fittings. Never vent refrigerant to atmosphere.
  • Manifold gauge interpretation pairs with ambient temperature. Both gauges low suggests an undercharge; both high suggests overcharge, poor condenser airflow, or an inoperative fan; high side very high with a low or normal low side suggests a restriction.
  • Expansion devices: an orifice tube is a fixed restriction; a thermal expansion valve modulates. Restrictions show as a temperature difference across the component.
  • Heater performance depends on coolant flow, blend door operation, and a properly burped cooling system.
  • Cabin air filter restriction reduces airflow without changing vent temperature.
  • Leak detection: UV dye, electronic sniffers, and pressure testing after recovery.

Traps

A/C that cools poorly at idle but well at speed usually points to condenser airflow, not charge. A compressor that will not engage may be disabled by a low-pressure switch, a bad clutch, or a control module command; verify the command before replacing the compressor. Do not assume a warm blend door is a refrigerant fault; check coolant level and heater hoses first.

Worked example

At 30 C ambient, a system shows low side 22 psi and high side 180 psi with poor cooling. Both gauges run low, so recover, evacuate, and recharge by weight to the underhood label rather than guessing, then verify pressures and vent temperature.

Rule of thumb

Charge by weight, never by gauge watching; approximate healthy R-134a readings near 30 C ambient are roughly 30 to 45 psi low side and 200 to 280 psi high side.

Engine Performance

Scope

Engine performance questions test diagnostic reasoning more than memorized specs. Know OBD-II monitors and readiness, DTC structure, freeze frame and live data, fuel trim, misfire diagnosis, and the basic air, fuel, and spark requirements.

Concepts you must own

  • DTCs describe a circuit or system, not a part. Confirm the fault with data before replacing anything.
  • Fuel trim: short-term is immediate correction, long-term is learned. Positive trim means the PCM is adding fuel to correct a lean condition; negative trim means it is pulling fuel from a rich condition.
  • Lean causes: vacuum leaks, low fuel pressure, dirty or under-reporting mass airflow sensor, exhaust leaks ahead of the oxygen sensor. Rich causes: leaking injectors, high fuel pressure, restricted air intake, failing coolant sensor biased cold.
  • Misfire: isolate by cylinder with a scan tool cylinder balance or by swapping ignition components. Check spark, fuel, and mechanical condition such as compression and valve sealing.
  • EVAP and catalyst monitors need specific drive cycles to run; a cleared code means all monitors reset.
  • Vacuum gauge and exhaust backpressure testing still solve problems scanners cannot.

Traps

A P0171 does not mean the oxygen sensor is bad; the sensor is often reporting correctly. Long-term trim beyond about plus or minus 10 percent indicates a real problem. Do not chase a misfire with parts without checking compression on the affected cylinder. Remember that a vacuum leak leans the engine most at idle, while a weak fuel pump leans it most under load; the trim pattern tells you which.

Worked example

Long-term fuel trim is plus 18 percent at idle and drops to plus 5 percent at 2500 rpm, with a rough idle. That pattern is a classic vacuum leak, since manifold vacuum is highest at idle. Smoke test the intake and repair the leak, then confirm trims normalize.

Rule of thumb

Positive fuel trim means lean, negative means rich; stay within about 10 percent either way.

ASE G1 cheat sheet

Quick reference

Engine Systems

  • Four-stroke cycle order is intake, compression, power, exhaust; the crankshaft rotates two full turns per complete cycle.

  • Stoichiometric gasoline air-fuel ratio is about 14.7:1 by mass under ideal combustion conditions.

  • A coolant thermostat begins opening near its rated temperature, commonly 180 to 195 degrees Fahrenheit, and reaches full opening above that rating.

  • Valve clearance is measured with a feeler gauge between the cam base circle and follower or valve stem, then compared with specification.

  • A stuck-closed PCV valve can allow crankcase pressure to build and force oil past seals.

  • An interference-engine timing belt failure can cause piston-to-valve contact and severe cylinder head damage.

  • An oil pressure warning switch typically closes to ground when pressure falls below a low threshold, commonly about 5 to 7 psi.

  • A cooling system pressure cap raises the boiling point by roughly 3 degrees Fahrenheit per psi of rating.

  • Cylinder leak-down air escaping from the intake indicates an intake valve leak; escaping from the oil filler indicates ring or cylinder wear.

Quick reference

Automatic Transmission and Transaxle

  • Automatic transmission fluid level is usually checked with the engine running and fluid warm, in Park or Neutral, or at an overflow plug at a specified temperature.

  • The torque converter stator multiplies torque at low speed ratio and approaches a fluid coupling near 1:1 speed ratio.

  • A failed shift solenoid can cause harsh shifting, a missing shift, or default limp mode operation.

  • Burnt fluid smell and debris indicate overheating or clutch material wear; color alone is not a definitive diagnosis.

  • Transmission line pressure typically increases with throttle opening and engine load.

  • A CVT changes ratio continuously with a steel belt or chain and variable-diameter pulleys and requires the specified CVT fluid.

  • After valve body or clutch repair, the transmission control module may require an adaptive relearn to restore shift quality.

  • A faulty vehicle speed sensor can cause incorrect shift points, no upshift, and speedometer error.

  • Torque converter clutch shudder is often caused by degraded automatic transmission fluid or a worn converter clutch lining.

Quick reference

Manual Drive Train and Axles

  • Clutch pedal free play is the clearance before the release bearing contacts the pressure plate; too little clearance can cause slip and bearing wear.

  • Manual transmission gear oil is checked at the fill plug with the vehicle level; fluid should be at the bottom edge of the fill hole.

  • A rhythmic click during turns usually indicates a worn outer CV joint; vibration under acceleration often indicates an inner CV joint.

  • Differential ring and pinion backlash is measured with a dial indicator against a tooth while the pinion is held stationary.

  • Clutch-type limited-slip differentials often require a friction modifier to prevent chatter during low-speed turns.

  • A worn universal joint can cause driveline vibration, a clunk during load changes, or a squeak during rotation.

  • Flywheel runout and step height affect clutch engagement and must be measured against specification during clutch service.

  • A leaking axle seal can contaminate brake shoes or pads and cause brake pull, noise, or lockup.

Quick reference

Suspension and Steering

  • Toe is the difference in track width measured at the front and rear of the tires; toe-in means the fronts are closer together than the rears.

  • Camber is the inward or outward tilt of the tire top relative to vertical; negative camber tilts the top inward.

  • Positive caster tilts the steering axis rearward at the top and improves straight-line stability and steering return.

  • Ride height should be checked before alignment because bent or sagging suspension components cannot be adjusted out.

  • Tire pressure affects rolling resistance, wear pattern, and TPMS operation; pressure should be set cold.

  • A worn tie rod end produces steering play and can cause uneven toe wear.

  • A MacPherson strut combines the spring and damper; a worn strut mount bearing can cause popping when turning.

  • Power steering whine is often caused by low fluid or air in the system and may require bleeding after repair.

  • Wheel bearing noise often changes when vehicle weight shifts side to side, helping identify the affected side.

Quick reference

Brakes

  • Glycol-based brake fluid is hygroscopic; absorbed moisture lowers its boiling point and can cause pedal fade under heavy braking.

  • DOT 3, DOT 4, and DOT 5.1 fluids are glycol-based; DOT 5 is silicone-based and must not be mixed with glycol fluid.

  • A disc brake rotor has a minimum thickness specification stamped or cast on the hub; a rotor below specification must be replaced.

  • Brake pedal pulsation is commonly caused by rotor thickness variation or lateral runout.

  • Brake drag can overheat the brakes, cause a pull, and accelerate pad wear; caliper slides and flexible hoses are common causes.

  • An illuminated ABS warning lamp indicates the antilock function is disabled, but conventional hydraulic brakes normally remain functional.

  • A parking brake should hold the vehicle and release without drag; adjustment is set to the specified lever travel or click count.

  • Brake line flares must match the fitting type, such as ISO bubble or double flare, to prevent leaks.

  • Contaminated brake pads or shoes from oil or grease can cause pulling, noise, and reduced friction.

Quick reference

Electrical and Electronic Systems

  • Ohm's law states V equals I times R; power can be calculated as P equals V times I, I squared times R, or V squared divided by R.

  • A voltage drop test measures loss across a circuit under load; excessive drop indicates high resistance in cables, connections, switches, or grounds.

  • Parasitic draw is measured with an ammeter in series after modules sleep; excessive draw is commonly specified below about 50 milliamps.

  • A fully charged lead-acid battery at rest typically measures about 12.6 volts open-circuit; lower voltage indicates partial discharge.

  • Series circuits share the same current; parallel circuits share the same voltage.

  • A relay coil can be controlled on the power side or ground side, so both control circuits must be verified.

  • A healthy CAN bus typically measures about 60 ohms across the communication lines because two 120-ohm terminating resistors are in parallel.

  • Charging voltage with the engine running is typically about 13.5 to 14.5 volts, depending on temperature and battery state.

  • A fuse must be replaced with the same rating because the fuse protects the wiring from overload.

Quick reference

Heating, Ventilation, and Air Conditioning

  • Refrigerant must be recovered with approved equipment and not vented to the atmosphere.

  • With the compressor engaged, low-side A/C pressure commonly reads about 25 to 45 psi, varying with ambient temperature and system design.

  • High-side A/C pressure commonly reads about 150 to 250 psi, depending on ambient temperature, condenser airflow, and refrigerant charge.

  • A compressor clutch that does not engage can be caused by low refrigerant pressure, an open pressure switch, a fuse, a relay, or incorrect clutch gap.

  • The blend door actuator moves a flap that directs air through or around the heater core to control outlet temperature.

  • A restricted cabin air filter reduces airflow and can cause weak vent output or persistent odors.

  • No cabin heat can result from low coolant, a stuck-open thermostat, a failed blend door, or a blocked heater core.

  • Refrigerant leaks are located with UV dye, an electronic leak detector, or soap bubbles, not by opening the system.

  • A good vacuum reading during A/C evacuation is about 28 to 30 inches of mercury, indicating moisture and air removal.

Quick reference

Engine Performance

  • Positive fuel trim means the control module is adding fuel to correct a lean condition; negative fuel trim means it is reducing fuel.

  • Diagnostic trouble code P0171 indicates bank 1 is lean; P0172 indicates bank 1 is rich.

  • A properly switching upstream oxygen sensor oscillates between about 0.1 and 0.9 volt.

  • The misfire monitor detects crankshaft speed fluctuations that occur when a cylinder fails to produce power.

  • A MAP sensor measures manifold pressure; with the key on and engine off, it should read near atmospheric pressure.

  • Ignition timing typically advances with engine speed and light load and retards when knock is detected.

  • A compression test is performed with the throttle open and all spark plugs removed; cylinder results should be within about 10 to 15 percent of each other.

  • An evaporative emission large-leak code such as P0455 is commonly caused by a loose fuel cap, disconnected hose, or failed purge valve.

  • A mass airflow sensor reading can be compared with specification at idle and at higher engine speed to identify contamination or airflow faults.

ASE G1 key terms

Engine oil viscosity

A measure of how thick an oil is and how easily it flows at a given temperature. Multigrade oils such as 5W-30 flow thin when cold and stay thicker when hot.

Related: Oil filter
Oil filter

A replaceable canister containing filter media that traps metal particles, sludge, and dirt from the oil before it is pumped back to the engine bearings and moving parts.

Related: Engine oil viscosity
Coolant

A mixture of water and antifreeze that carries heat away from the engine. It raises the boiling point and lowers the freezing point so the cooling system works in all climates.

Related: Thermostat
Thermostat

A temperature-controlled valve in the cooling system. It stays closed while the engine warms and opens at a set temperature to let coolant flow through the radiator.

Related: Coolant
Serpentine belt

One wide, ribbed belt that drives the alternator, power steering pump, water pump, and A/C compressor on most late-model engines. An automatic tensioner keeps it tight.

Related: Alternator, A/C compressor
Automatic transmission fluid (ATF)

A hydraulic oil made for automatic transmissions. It transmits pressure to apply clutches and bands, lubricates internal parts, and carries heat to the cooler.

Related: Torque converter
Torque converter

A fluid coupling between the engine and an automatic transmission. It multiplies engine torque at low speed and lets the car stop in gear without stalling.

Related: Automatic transmission fluid (ATF)
Transmission control module (TCM)

A computer that reads vehicle speed, throttle position, and temperature, then commands shift solenoids and line pressure inside an automatic transmission.

Related: Automatic transmission fluid (ATF)
Continuously variable transmission (CVT)

A transmission that uses a steel belt or chain running between two pulleys whose width changes, giving an infinite number of ratios instead of fixed gear steps.

Related: Automatic transmission fluid (ATF)
Clutch

A friction assembly between the engine flywheel and a manual transmission. It engages and disengages power flow so the driver can start from a stop and shift gears.

Related: Release (throw-out) bearing
Release (throw-out) bearing

A bearing that presses against the pressure plate fingers when the clutch pedal is pushed, releasing the disc so engine power no longer reaches the transmission.

Related: Clutch
Constant-velocity (CV) joint

A flexible joint at each end of a front-wheel-drive halfshaft. It carries power through a changing angle at constant speed while the suspension moves and the wheels steer.

Differential

A gear set that divides engine torque between the drive wheels and lets them turn at different speeds, which is needed when the vehicle goes around a turn.

MacPherson strut

A suspension design where the shock absorber is built into a structural strut that also locates the wheel. It is common on the front of unit-body cars.

Related: Wheel alignment
Ball joint

A socket-and-stud pivot that connects a control arm to the steering knuckle. It lets the suspension move up and down while the wheel still steers.

Related: Tie rod end
Tie rod end

The outer, adjustable end of the steering linkage. It connects the steering rack or gear to the knuckle and is adjusted to set toe during an alignment.

Related: Wheel alignment
Wheel alignment

Adjusting camber, caster, and toe so the wheels point where the manufacturer specifies relative to the vehicle and to each other.

Related: Tie rod end
Brake pad

Friction material bonded to a steel backing plate. The caliper squeezes the pad against the rotor to slow the wheel.

Related: Brake rotor (disc), Brake caliper
Brake rotor (disc)

The rotating iron disc that the brake pads clamp on. It must stay above a minimum thickness and within runout limits to brake smoothly.

Related: Brake pad
Brake caliper

A hydraulic housing that holds the brake pads. Fluid pressure pushes one or more pistons out to clamp the pads on the rotor.

Related: Brake pad, Brake fluid
Brake fluid

A hydraulic fluid rated by DOT number that carries pedal force to the calipers and wheel cylinders. It absorbs moisture from the air and should be replaced on schedule.

Related: Brake caliper
ABS wheel speed sensor

A sensor at each wheel that reports how fast the wheel is turning. The ABS module uses those signals to detect and prevent wheel lockup during hard braking.

Voltage drop test

A check of how much voltage is lost across a cable, connection, or ground while current is flowing. More than about 0.1 volt per connection points to excess resistance.

Related: Multimeter
Multimeter

A test instrument that measures voltage, resistance, and current. A digital multimeter is the basic tool for checking circuits, sensors, and battery condition.

Related: Voltage drop test
Parasitic draw

Current a vehicle keeps drawing from the battery after all accessories are off and the modules have gone to sleep. Too much draw causes a dead battery overnight.

Related: Multimeter
Alternator

A belt-driven generator that makes alternating current, converts it to direct current, and keeps the battery charged while the engine is running.

Related: Serpentine belt
Relay

An electrically operated switch. A small coil current closes contacts that carry the much larger current needed by items like a fuel pump or cooling fan.

Refrigerant

The fluid in an A/C system that absorbs heat when it evaporates in the evaporator and releases heat when it condenses in the condenser.

Related: A/C compressor
A/C compressor

A belt-driven pump that raises refrigerant pressure and temperature so heat can be released at the condenser. It also circulates refrigerant and lubricating oil through the system.

Related: Refrigerant, Manifold gauge set
Manifold gauge set

A two-gauge tool with hoses that connects to the high and low service ports of an A/C system to read pressures and to add or recover refrigerant.

Related: Refrigerant
Heater core

A small radiator inside the dash that uses hot engine coolant to warm air blown through it for cabin heat and defrost.

Related: Coolant
Diagnostic trouble code (DTC)

An alphanumeric code a control module stores when a monitored circuit or system fails its self-test. The code names the circuit, not the part to replace.

Related: Malfunction indicator lamp (MIL), Scan tool
Malfunction indicator lamp (MIL)

The check engine light on the dash. It comes on when the powertrain control module sets an emissions-related fault code.

Related: Diagnostic trouble code (DTC)
Fuel trim

Short- and long-term corrections the PCM makes to fuel delivery based on oxygen sensor feedback. Positive trim means the engine is running lean and needs more fuel.

Related: Oxygen sensor
Oxygen sensor

A sensor in the exhaust stream that generates a signal based on the oxygen left in the exhaust, letting the PCM judge whether the mixture is rich or lean.

Related: Fuel trim
Scan tool

A diagnostic device that plugs into the OBD-II connector to read codes, display live sensor data, and command tests on vehicle modules.

Related: Diagnostic trouble code (DTC), Malfunction indicator lamp (MIL)

ASE G1 study plan

8 weeks · About 6 hours per week

Week 1

Engine Systems

  • Identify and locate the major mechanical systems of a gasoline engine (block, heads, valvetrain, timing drive, lubrication, cooling) on a diagram and on a live engine.

  • Explain the four-stroke cycle and correlate each stroke to valve, piston, and ignition events.

  • Diagnose three common engine mechanical complaints (oil consumption, coolant loss, unusual noise) by listing the test that confirms each cause.

  • Perform and interpret a compression test and a cylinder leak-down test, stating pass/fail criteria.

Your checkpoint

A one-page engine-systems diagnostic sheet covering compression, leak-down, oil pressure, and cooling-system pressure tests, plus a score of 80% or better on a 40-question Domain 1 practice set.

Week 2

Engine Systems & Electrical and Electronic Systems

  • Trace the lubrication and cooling circuits from pump to return, naming each component and its failure symptom.

  • Describe the purpose and operation of the battery, starting, and charging systems using correct terminology (CEMF, parasitic draw, voltage drop).

  • Calculate expected voltage drop and resistance in a series/parallel circuit using Ohm's law.

  • Demonstrate safe and correct use of a DMM to measure voltage, resistance, current, and voltage drop on a live circuit.

Your checkpoint

A completed voltage-drop worksheet with five worked circuit problems plus measured readings from at least three actual vehicle circuits, all within 0.5 V of specification.

Week 3

Electrical and Electronic Systems & Engine Performance

  • Diagnose an open, short-to-ground, and high-resistance fault using a wiring diagram and a systematic test sequence.

  • Interpret OBD-II readiness monitors, freeze-frame data, and stored/pending DTCs to build a diagnostic path.

  • Connect and use a scan tool to read live data (fuel trims, O2 response, MAF/MAP, coolant temp) and state what each value indicates.

  • Explain the relationship between air/fuel metering, ignition, and emission control as it applies to a driveability complaint.

Your checkpoint

A written diagnostic case study of one simulated driveability complaint: symptom, tests performed, data recorded, root cause, and repair verification.

Week 4

Engine Performance

  • Diagnose a no-start, a rough idle, and a misfire by selecting the correct test sequence and interpreting the results.

  • Verify fuel delivery (pressure, volume, and injector operation) and ignition output using the correct tools.

  • Explain how fuel trim values shift in response to vacuum leaks, weak fuel delivery, and faulty sensors.

  • Distinguish mechanical, ignition, and fuel-related causes of a misfire and justify the diagnosis with data.

Your checkpoint

A timed 60-question mixed Domain 1/6/8 practice exam scored at 80% or better, with every missed question rewritten as a corrected one-line rule.

Week 5

Automatic Transmission and Transaxle & Brakes

  • Identify the major components of an automatic transmission/transaxle and describe the function of the torque converter, planetary gearset, and hydraulic control circuit.

  • Perform and interpret a fluid level/condition check and explain the diagnostic meaning of fluid color, smell, and debris.

  • Describe the operation of disc, drum, and parking brake systems and identify the cause of common pedal-feel complaints (spongy, low, hard, fading).

  • Measure brake pad/shoe and rotor/drum thickness and compare results to specification.

Your checkpoint

A two-part lab write-up: a transmission/transaxle symptom-to-cause chart with at least eight entries, and a completed brake measurement record with pass/fail calls against specification.

Week 6

Manual Drive Train and Axles & Suspension and Steering

  • Describe the power flow through a clutch, manual transmission, driveshaft, differential, and axle, and name the failure symptom for each stage.

  • Explain the difference between front-engine FWD, RWD, and AWD/4WD layouts including CV joints, universal joints, and transfer cases.

  • Identify suspension types (strut, SLA, live axle) and steering types (rack-and-pinion, recirculating ball) and their alignment implications.

  • Explain camber, caster, toe, and thrust angle, and predict the handling or tire-wear symptom produced by each being out of specification.

Your checkpoint

An alignment-and-tire-wear cause/effect chart mapping at least six wear patterns to the alignment angle or suspension defect responsible, plus a scored 30-question Domain 3/4 practice set.

Week 7

Heating, Ventilation and Air Conditioning & Electrical and Electronic Systems

  • Explain the refrigeration cycle and identify the function of the compressor, condenser, expansion device, and evaporator.

  • Describe safe refrigerant handling, recovery/recycling procedures, and the required personal protective equipment.

  • Diagnose a no-cool and a no-heat complaint using pressure readings, vent temperature, and blend-door/actuator checks.

  • Trace the control circuit for a blower motor and HVAC actuator through a wiring diagram and state how to test each component.

Your checkpoint

A completed HVAC diagnostic decision tree covering high/low-side pressure combinations (both high, both low, high-low, low-high) with the probable cause listed for each.

Week 8

Engine Systems & Automatic Transmission and Transaxle & Manual Drive Train and Axles & Suspension and Steering & Brakes & Electrical and Electronic Systems & Heating, Ventilation and Air Conditioning & Engine Performance

  • Re-test every domain and rank them from weakest to strongest by score.

  • Re-study only the two lowest-scoring domains, focusing on the specific missed objectives rather than broad review.

  • Practice time management by completing a full-length timed practice exam under test-day conditions.

  • Explain, in writing, the correct diagnostic sequence for five frequently missed question types.

Your checkpoint

A final full-length timed practice exam scored at 85% or better, with a one-page 'final 48 hours' review sheet listing the rules for the ten questions most often missed across all attempts.

Milestones

Week 2: Can explain the four-stroke cycle, name the components of the lubrication and cooling systems, and measure voltage drop on a live circuit without reference notes.

Week 4: Scored 80% or better on a 60-question mixed Domain 1/6/8 exam; every missed question has a written corrected rule.

Week 6: Scored 75% or better on each of the Domain 2/5 and Domain 3/4 practice sets, and can state the handling symptom caused by each misadjusted alignment angle.

Week 8: Scored 85% or better on the full-length timed exam with no domain below 75%, and the final review sheet is complete.

ASE G1 exam day

Your checklist

Admission ticket or appointment confirmation

Bring the confirmation ASE sends after you schedule your G1 appointment. Confirm with the provider whether a printed copy is required or a digital copy on your phone is accepted before you enter the testing room.

Valid government-issued photo ID

The name on the ID must match your registration exactly. Check the provider's list of accepted ID types and expiration requirements well before test day; an expired or mismatched ID can bar you from testing.

Directions, parking, and arrival plan

Confirm the test center address and how long the trip takes. Plan to arrive with buffer time; confirm with the provider how early they want you to check in.

Confirmed registration for the correct test

Verify in your ASE account that you are scheduled for G1 (Maintenance and Light Repair) on the correct date and that any eligibility or prerequisite requirements are satisfied.

Knowledge of prohibited items and storage

Phones, smartwatches, notes, and study materials are generally not allowed in the testing room. Ask the provider in advance what storage (locker, shelf) is available so you know whether to leave items at home or in your vehicle.

Understanding of the scoring and retest policy

Know how results are reported and what the process is if you do not pass, including any waiting period before a retest. Ask ASE directly rather than relying on secondhand information.

Clarification on breaks and timing

Ask whether breaks are built into the appointment, whether unscheduled breaks stop the clock, and whether you can leave the building during a break. Policies vary, so confirm with the provider.

Approved accommodations arranged in advance (if applicable)

If you need testing accommodations, they must typically be requested and approved before the appointment. Contact the provider well ahead of test day.

Light meal, hydration, and rest the night before

Eat a normal meal before arriving and get a full night's sleep. Avoid heavy caffeine if you are not accustomed to it; there is no advantage to arriving hungry or over-caffeinated.

A short, calm review of the G1 task list

In the final day, skim the published G1 task areas only to refresh familiarity. Do not attempt to learn new material; last-minute cramming of unfamiliar content tends to increase anxiety without improving recall.

Plan for leaving your phone and belongings

Decide in advance where your phone, keys, and bag will go. Many centers provide a small locker, but capacity varies; confirm with the provider if you plan to bring a bag.

Plan the day

Final 72 hours

Confirm your appointment details, ID, and test center location in writing. Re-read the G1 task list at a high level and stop studying new topics. Protect your sleep schedule and avoid late-night cramming.

Final 24 hours

Lay out your ID and confirmation, pack nothing you do not need, and check the weather and traffic plan for the route. Do a light review of areas you already know well. Get to bed at a normal hour.

Morning of the test

Eat a normal meal, arrive with buffer time, and leave prohibited items in the vehicle or at home if storage is limited. Check in at the front desk, present your ID, and follow the proctor's instructions for securing belongings.

During the test

Read each question completely and watch for qualifiers such as 'except' or 'most likely.' Answer every question; there is no penalty described for guessing, but confirm this with the provider. Flag uncertain items only if the interface allows review, and manage your pace against the remaining time shown.

If you finish early

Use remaining time to review flagged questions and to re-check answers you changed; change an answer only when you have a specific reason, not out of doubt alone.

After the test

Follow the provider's instructions on how and when results are issued, and keep your score report. If you did not pass, ask ASE about the retest window and use the task-area breakdown, if provided, to target your study.

Rules to check

  • Bring valid government-issued photo ID with a name matching your registration exactly; without acceptable ID you may be turned away and your fee forfeited. Confirm accepted ID types with the provider.

  • Do not bring phones, smartwatches, notes, or study materials into the testing room. Follow the proctor's instructions for storing personal items.

  • Follow all proctor instructions and testing-room conduct rules; talking, sharing materials, or attempting to record questions can result in dismissal and score cancellation.

  • Ask the provider in advance how breaks work and whether the clock stops during them; do not assume unscheduled breaks pause your time.

  • Scoring is based on the number of questions you answer correctly, and ASE sets the passing standard; do not expect partial credit for unanswered items, so answer every question. Confirm scoring details with ASE.

  • Retest and waiting-period policies are set by ASE; confirm the current rules before scheduling a second attempt.

  • Report any testing-environment problem, such as a malfunctioning workstation or excessive noise, to the proctor immediately rather than waiting until the end.

  • If you need accommodations, request them through the provider before test day; accommodations generally cannot be arranged at the counter on the morning of the exam.

ASE G1 FAQ

How many ASE G1 practice questions are available?

The practice set has 200 ASE G1 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many ASE G1 flashcards are available?

The flashcard set has 32 ASE G1 cards. Each card shows the term and its definition.

Which topics does the ASE G1 study material cover?

The ASE G1 study material has 8 sections, including Engine Systems, Automatic Transmission and Transaxle, and Manual Drive Train and Axles.

What format facts does the catalog list for the ASE G1 exam?

The catalog lists these item types: multiple choice for the ASE G1 exam.