ASE A4 Practice Test

ASE A4 - Suspension and Steering (Automobile and Light Truck Certification)

ASE A4 overview

  • 200 practice questions
  • 32 flashcards
  • 5 study guide topics
  • 39 key terms

What you'll study

  • Steering Systems20%
  • Suspension Systems20%
  • Wheel Alignment20%
  • Wheels and Tires20%
  • Miscellaneous (Related Suspension and Steering Diagnosis and Repair)20%

ASE A4, Suspension and Steering, is one of the automobile and light truck certification tests administered by the National Institute for Automotive Service Excellence (ASE), an organization that certifies automotive service professionals across dealerships, independent shops, fleets, schools and colleges. ASE certification is a voluntary, industry-recognized credential meant to show verified technical knowledge rather than simply years on the job. The A4 test is built for technicians who diagnose, service and repair steering and suspension systems on passenger cars and light trucks: steering columns, gears, pumps, linkage and electric power steering, springs, struts, shocks, control arms, bushings and ball joints, wheel alignment angles and adjustments, wheels, tires, bearings and tire pressure monitoring, plus the electrical, hydraulic and diagnostic work that ties those systems together. Questions are multiple choice and are written to reflect real shop practice, including symptom-based diagnosis, measurement and safe repair procedures. Because ASE periodically revises its tests and publishes registration details through its own channels, candidates should confirm current test length, content weighting, scoring and fees directly with ASE at the time they register. A sensible preparation plan combines hands-on practice with ASE's own study guides and practice test offerings, then targeted review of whichever system area you touch least often in daily work.

Common mistakes

Adjusts toe first and treats toe as the only alignment angle, skipping ride-height, camber, caster, and thrust-angle checks.

Toe is the easiest and most visible adjustment, so candidates jump to tie-rod turning before verifying the conditions that affect toe and steering-wheel position.

What to do instead

Follow the alignment sequence: inspect and set ride height, check subframe/thrust angle, adjust camber and caster, then set toe last with the steering wheel centered.

Centers an off-center steering wheel by turning only one tie rod or by unequal tie-rod adjustment without checking steering-angle sensor or clockspring position.

The steering wheel looks like a simple toe problem, so candidates correct the visible symptom without considering tie-rod equalization, bump steer, or steering-angle sensor calibration.

What to do instead

Center the steering wheel and secure it, adjust each tie rod equally in opposite directions to set toe, then verify/calibrate the steering-angle sensor if equipped.

Condemns a ball joint by prying it while the suspension is hanging at full droop or by prying in the wrong direction.

Unloaded suspension changes ball-joint geometry and can show false play; candidates may also pry against a spring-loaded joint instead of measuring specified axial/radial play.

What to do instead

Use the OEM inspection procedure: load the suspension at normal ride height where required, pry/measure in the specified direction, and compare against the service limit.

Chases a pull or vibration with alignment only, without road-testing, checking tire pressure/size matching, or measuring tire/wheel runout and conicity.

Tire defects, mismatched tires, and runout can mimic alignment problems, and alignment cannot correct a tire-induced pull or vibration.

What to do instead

Road-test and inspect tires first: verify pressure and size, swap tires side-to-side or front-to-rear, measure radial/axial runout, and correct tire/wheel issues before alignment.

Replaces a power steering pump for whine or poor assist without checking fluid level, aeration/bleeding, belt condition, and pressure/flow.

Low fluid, air in the system, a slipping belt, or a restricted line can produce the same symptoms as a failed pump.

What to do instead

Check and correct fluid level, bleed air per OEM procedure, inspect the belt and pulley, and perform pressure/flow testing before condemning the pump.

Attempts to adjust camber or caster to specification without first measuring ride height and inspecting for subframe shift or damaged suspension components.

Ride height and subframe position change camber, caster, and thrust angle; adjusting alignment on a bent or mislocated foundation produces a false result.

What to do instead

Measure ride height against specification, inspect for subframe shift/collision damage, correct ride-height or subframe issues first, then perform the alignment.

Reuses torque-to-yield suspension fasteners or tightens rubber-bushing pivot bolts with the suspension at full droop.

Candidates treat all fasteners as reusable and tighten bushings in the easiest position, which twists the rubber and can cause premature failure or incorrect ride height.

What to do instead

Replace torque-to-yield fasteners per OEM, and torque bushing pivot bolts at normal ride height with the suspension loaded unless the service procedure states otherwise.

Services the steering column or clockspring without disabling the SRS and without locking/centering the steering wheel.

The airbag and clockspring are easily damaged during column work, and candidates may not follow the required SRS disable and steering-lock precautions.

What to do instead

Disable the SRS per OEM procedure, wait the specified time, lock the steering wheel in the centered position, and center/index the clockspring before reassembly.

Completes an alignment or steering-column repair without resetting/calibrating the steering-angle sensor or reinitializing ADAS features.

Mechanical alignment alone does not update the electronic zero point; candidates may not scan for steering-angle or stability-control codes after repairs.

What to do instead

Use a scan tool to clear codes and perform steering-angle sensor calibration/relearn and any required ADAS or stability-control initialization after alignment or column work.

Mounts directional or asymmetric tires backward or skips TPMS relearn after tire/wheel service.

Candidates focus on mounting and balancing and overlook sidewall direction/outboard markings and the need to register sensor IDs.

What to do instead

Match directional arrows and asymmetric outboard markings during mounting, then perform the specified TPMS relearn and verify pressures.

Exam requirements can change. Confirm current details with the exam provider.

ASE A4 practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Steering Systems

    The collapsible section of a steering column is designed primarily to do which of the following?

    1. Reduce the turning radius
    2. Dampen road shock to the steering wheel
    3. Absorb energy in a frontal collision Correct answer.
    4. Increase the steering ratio

    Explanation

    A collapsible column compresses or separates during a frontal impact so the column does not push into the driver. It works with the column's shear capsules and energy-absorbing design. Steering ratio, turning radius, and road-shock damping are not its purposes.

  2. Question 2Steering Systems

    Which component carries steering force from the steering gear to the steering knuckle on a rack-and-pinion system?

    1. Sector shaft
    2. Idler arm
    3. Pitman arm
    4. Tie rod Correct answer.

    Explanation

    The inner and outer tie rod assembly links the rack to the steering knuckle. The idler arm and pitman arm belong to parallelogram linkage, and the sector shaft is part of the steering gear.

  3. Question 3Steering Systems

    A vehicle with a belt-driven hydraulic power steering pump should be serviced with which fluid?

    1. Ethylene glycol engine coolant
    2. The specified power steering fluid Correct answer.
    3. DOT 3 brake fluid from the master cylinder
    4. Engine oil drained from the crankcase

    Explanation

    Power steering systems require the fluid specified by the manufacturer, which may be a dedicated power steering fluid or a specific automatic transmission fluid. Using the wrong fluid can damage seals and affect steering feel.

  4. Question 4Steering Systems

    Which statement correctly describes positive camber?

    1. The top of the wheel tilts outward Correct answer.
    2. The wheel center moves rearward
    3. The steering axis tilts rearward at the top
    4. The top of the wheel tilts inward

    Explanation

    Camber is the inward or outward tilt of the wheel from vertical. Positive camber tilts the top of the wheel outward, away from the vehicle centerline.

  5. Question 5Steering Systems

    Excessive free play at the steering wheel is most commonly caused by which condition?

    1. Worn brake pads
    2. Worn tie rod ends Correct answer.
    3. Misaimed headlamps
    4. Low tire pressure

    Explanation

    Free play is lost motion between the steering wheel and the road wheels. Worn tie rod ends, worn steering gear parts, or a loose steering shaft coupling are typical causes. Tire pressure, headlamp aim, and brakes do not create steering free play.

  6. Question 6Steering Systems

    A squealing noise is heard when turning at low speed on a vehicle with a belt-driven power steering pump. Which is the most likely cause?

    1. Worn strut mount bearings
    2. A slipping pump belt Correct answer.
    3. Excessive positive caster
    4. A seized idler arm bushing

    Explanation

    When the pump loads up at low speed, a glazed, loose, or contaminated belt can slip and squeal. Checking belt condition and tension is the first diagnostic step.

  7. Question 7Steering Systems

    The accordion boot on a rack-and-pinion steering gear serves which purpose?

    1. Hold hydraulic pressure inside the rack
    2. Adjust the toe setting
    3. Keep contaminants out of the rack Correct answer.
    4. Preload the pinion against the rack

    Explanation

    The boot seals the rack housing where the tie rod exits. It keeps dirt and water away from the rack seal and inner tie rod socket. It carries no hydraulic pressure and makes no adjustment.

  8. Question 8Steering Systems

    The turning radius of a vehicle refers to which of the following?

    1. The circle the vehicle traces at full lock Correct answer.
    2. The distance from the steering axis to the tire center
    3. The angle of the front wheels
    4. The diameter of the steering wheel

    Explanation

    Turning radius, often quoted as a turning circle, describes the size of the path the vehicle follows with the steering at full lock. It depends on wheelbase, track width, and steering angle.

  9. Question 9Steering Systems

    A vehicle has a total toe reading of -0.30 degrees, which is toe-out. To bring it to the specified total toe-in of +0.10 degrees, the tie rods should be adjusted so that the front of the tires does which of the following?

    1. Increases camber on both sides
    2. Moves inward Correct answer.
    3. Moves rearward in the wheel wells
    4. Moves outward

    Explanation

    Total toe is the sum of both wheel toe angles. A negative value means the fronts of the tires point away from each other, so bringing them inward moves the reading toward toe-in.

  10. Question 10Steering Systems

    During a power steering pump pressure test, the gauge reads well below specification when the shutoff valve is briefly closed. Which is the most likely cause?

    1. A worn pump or stuck relief valve Correct answer.
    2. A loose steering wheel retaining nut
    3. Excessive positive caster on the front wheels
    4. Air trapped in the system only

    Explanation

    Closing the valve deadheads the pump, so the gauge should reach the specified maximum pressure. A low reading indicates the pump cannot build pressure, often from worn parts or a relief valve stuck open.

  11. Question 11Steering Systems

    In an electric power steering system, the control module uses the steering torque sensor signal to do which of the following?

    1. Adjust the tire pressure monitor threshold
    2. Determine how much assist current to apply Correct answer.
    3. Set the radio volume
    4. Control the brake proportioning valve

    Explanation

    The torque sensor reports how hard the driver is turning the wheel. The module combines that with vehicle speed and other inputs to command the assist motor current.

  12. Question 12Steering Systems

    A recirculating-ball steering gear shows excessive play at the pitman arm. Which adjustment addresses this condition?

    1. Shim the pump mounting bracket
    2. Adjust the sector shaft lash Correct answer.
    3. Replace the idler arm bushing
    4. Adjust the front toe setting

    Explanation

    Sector shaft lash removes play between the sector gear and the ball nut. Worm bearing preload should be checked first, then the lash screw is adjusted per the service procedure.

  13. Question 13Steering Systems

    A vehicle has dark, contaminated power steering fluid and a whining pump. Which is the best first step?

    1. Flush the fluid and check for leaks Correct answer.
    2. Increase the drive belt tension
    3. Replace the rack and pinion assembly
    4. Add brake fluid to the reservoir

    Explanation

    Contaminated fluid and noise often indicate a fluid or aeration problem, and flushing with the specified fluid is a standard first step. The system should then be inspected for leaks and air entry.

  14. Question 14Steering Systems

    Which statement best describes bump steer?

    1. A pull during braking
    2. The wheel returning to center after a turn
    3. A vibration at highway speed
    4. A change in toe as the suspension moves Correct answer.

    Explanation

    Bump steer is toe change that occurs as the suspension travels. It results from misaligned tie rod and control arm geometry and can make the vehicle wander over uneven roads.

  15. Question 15Steering Systems

    After replacing a steering rack on a vehicle equipped with stability control, the technician should perform which action?

    1. Perform a steering angle sensor calibration Correct answer.
    2. Disable the ABS permanently
    3. Top off the system with brake fluid
    4. Replace the yaw rate sensor

    Explanation

    The stability control system needs to know the straight-ahead steering position. After rack replacement or alignment, the steering angle sensor must be recalibrated with a scan tool.

  16. Question 16Steering Systems

    A vehicle has caster readings of +2.0 degrees on the left and +4.0 degrees on the right, and it pulls left. Which statement is correct?

    1. It pulls toward the side with less caster, so it pulls left Correct answer.
    2. It pulls toward the side with more caster, so it pulls right
    3. The pull is caused only by the toe setting
    4. Caster has no effect on directional pull

    Explanation

    Caster creates a directional force, and the vehicle tends to lead toward the side with less positive caster. With 2.0 degrees on the left and 4.0 on the right, the left side has less caster and the vehicle pulls left.

  17. Question 17Steering Systems

    In a parallelogram steering linkage, which component transfers motion from the pitman arm across to the idler arm?

    1. Steering knuckle
    2. Center link Correct answer.
    3. Tie rod end
    4. Sector shaft

    Explanation

    The center link, also called a drag link, connects the pitman arm to the idler arm. The tie rod ends then carry motion out to the steering knuckles.

  18. Question 18Steering Systems

    A front wheel with a worn lower ball joint typically shows which symptom during inspection?

    1. A fluid leak at the rack boot
    2. Hard steering effort only at idle
    3. A vibration felt only above 60 mph
    4. Play between the knuckle and control arm Correct answer.

    Explanation

    A worn ball joint allows relative movement between the steering knuckle and the control arm. This is checked by prying the joint or observing vertical play with the suspension loaded or unloaded per the manufacturer's procedure.

  19. Question 19Steering Systems

    A power steering system is noisy and steering effort is high, and the return hose is found collapsed. Which repair is correct?

    1. Adjust the drive belt tension
    2. Add stop-leak to the reservoir
    3. Replace the power steering pump
    4. Replace the restricted return hose Correct answer.

    Explanation

    A collapsed return hose restricts fluid flow back to the reservoir, causing aeration, noise, and high effort. Replacing the restricted hose restores normal flow.

  20. Question 20Steering Systems

    A rack-and-pinion gear has slight looseness felt over bumps, and play is found at the inner tie rod. Which should be checked first?

    1. Front camber on both sides
    2. Wheel balance and tire radial runout
    3. Inner tie rod play and rack preload Correct answer.
    4. The power steering belt tension

    Explanation

    Play at the inner tie rod socket and incorrect rack guide preload both produce looseness felt through the steering wheel. Both should be inspected before condemning other components.

  21. Question 21Steering Systems

    On a vehicle with independent front suspension, steering axis inclination is out of specification on one side while camber is within specification. Which is the most likely cause?

    1. Worn outer tie rod ends
    2. A bent steering knuckle or strut Correct answer.
    3. An incorrect toe setting
    4. Low tire pressure on one side

    Explanation

    Steering axis inclination is built into the knuckle and strut geometry, so it is not adjustable. An out-of-spec reading on one side with acceptable camber usually indicates a bent knuckle, strut, or spindle.

  22. Question 22Steering Systems

    A power steering pump produces normal maximum deadhead pressure but low flow at idle. Which is the most likely cause?

    1. Excessive positive caster
    2. A worn pump or sticking flow control valve Correct answer.
    3. A loose pitman arm nut
    4. A seized pump drive shaft

    Explanation

    Maximum pressure and flow are separate pump functions. If pressure is normal but flow is low, the pump's flow control valve or internal clearances are the likely fault.

  23. Question 23Steering Systems

    When a vehicle turns, the inner front wheel should do which of the following?

    1. Turn a greater angle than the outer wheel Correct answer.
    2. Turn less than the outer wheel
    3. Turn the same angle as the outer wheel
    4. Remain parallel to the vehicle centerline

    Explanation

    Ackermann steering geometry causes the inner wheel to follow a tighter radius, so it turns a greater angle than the outer wheel. This reduces tire scrub during turns.

  24. Question 24Steering Systems

    What is the primary function of a steering damper on a vehicle with a solid front axle?

    1. Dampen road shock and shimmy at the steering wheel Correct answer.
    2. Center the wheel after a turn
    3. Increase the caster angle
    4. Reduce steering effort at low speed

    Explanation

    A steering damper is a hydraulic shock absorber mounted in the steering linkage. It controls sudden steering inputs and shimmy caused by road irregularities or large tires.

  25. Question 25Steering Systems

    An electric power steering system intermittently loses assist and sets a torque sensor code. Which is the most likely cause?

    1. An incorrect toe setting
    2. Low tire pressure on both front tires
    3. Worn outer tie rod ends
    4. A faulty torque sensor or wiring Correct answer.

    Explanation

    An intermittent assist loss with a torque sensor code points to a signal problem, such as a failing sensor or a poor connection. The circuit should be tested before replacing the motor or module.

  26. Question 26Steering Systems

    Steering wheel free play is being measured on a vehicle equipped with power steering. The measurement should be taken with the front wheels straight ahead and the engine:

    1. running at 2500 rpm
    2. running at idle speed Correct answer.
    3. off with the key removed
    4. off with the front wheels raised off the ground

    Explanation

    Free play is measured with the tires on the ground, the wheels straight ahead, and the engine idling so the booster is pressurized as it is in normal service. The wheel is turned until the front wheels just begin to move, and that movement is compared with specification.

  27. Question 27Steering Systems

    The collapsible section built into a steering column is designed to:

    1. let the driver adjust the column angle
    2. take up wear inside the steering gear
    3. collapse to absorb energy in a frontal impact Correct answer.
    4. damp road shock before it reaches the steering wheel

    Explanation

    The collapsible section is a safety feature: in a frontal impact the column shortens rather than driving rearward into the driver. It is a one-time energy-absorbing design, not a comfort or wear-compensation component.

  28. Question 28Steering Systems

    The threaded adjusting sleeve on a tie rod is used to:

    1. lock the tie rod to the steering knuckle
    2. change tie rod length to set toe Correct answer.
    3. set the preload on the tie rod ball stud
    4. adjust the mesh preload in the steering gear

    Explanation

    The sleeve joins two threaded tie rod sections, so rotating it changes the overall length and moves the wheel in or out to set toe. The clamp bolts are tightened with the linkage at normal ride height after the adjustment is made.

  29. Question 29Steering Systems

    On a hydraulically assisted steering system, a pressure switch threaded into a power steering line is used to:

    1. warn the driver when fluid level is low
    2. disengage the pump drive at highway speed
    3. raise idle speed when steering load is high Correct answer.
    4. limit maximum pressure at full lock

    Explanation

    The switch senses the pressure rise that occurs when the driver turns the wheel on a stationary or slow-moving vehicle and signals the control module to raise idle speed. This keeps the pump from stalling and preserves assist during parking maneuvers.

  30. Question 30Steering Systems

    A vehicle has too little positive caster on the front wheels. Which symptom is most likely?

    1. Wandering and slow return to center Correct answer.
    2. A shimmy that appears only while braking
    3. Rapid wear on the inside edges of both front tires
    4. A pull toward the side with the least positive camber

    Explanation

    Caster is the steering-axis tilt that makes the front wheels self-align, so too little positive caster reduces straight-line stability and slows the return to center after a turn. Tire wear patterns and braking shimmy are traced to other causes.

  31. Question 31Steering Systems

    A vehicle has steering axis inclination of 10 degrees on the left and 13 degrees on the right, with camber within specification on both sides. What does this indicate?

    1. Worn outer tie rod ends on the right side
    2. A bent right steering knuckle or strut Correct answer.
    3. A collapsed front spring on the left side
    4. Excessive total toe-in

    Explanation

    Included angle is the sum of steering axis inclination and camber. When camber is within specification, a side-to-side difference in SAI and included angle points to a bent knuckle, strut, or spindle on the side with the abnormal reading, because those parts establish the steering axis.

  32. Question 32Steering Systems

    The flow control valve in a power steering pump serves to:

    1. bypass fluid when the fluid is cold
    2. relieve pressure when the wheels reach full lock
    3. limit fluid flow as engine speed rises Correct answer.
    4. hold system pressure constant at all speeds

    Explanation

    The flow control valve regulates the volume of fluid the pump delivers so that flow, and therefore assist, stays nearly constant as engine speed increases. Peak pressure at full lock is handled by a separate relief valve.

  33. Question 33Steering Systems

    Compared with a 16:1 steering gear of the same type, a 20:1 steering gear will:

    1. require more effort with fewer turns lock to lock
    2. increase toe-out on turns at full lock
    3. respond more quickly with the same effort
    4. require less effort with more turns lock to lock Correct answer.

    Explanation

    A numerically higher ratio means the steering wheel must turn farther for a given road wheel angle. That reduces the effort needed at the rim but increases the number of turns lock to lock and slows response.

  34. Question 34Steering Systems

    On a speed-sensitive electric power steering system, assist is reduced as vehicle speed increases in order to:

    1. protect the assist motor from overheating
    2. keep the battery from discharging at speed
    3. maintain calibration of the steering angle sensor
    4. improve road feel and stability at highway speed Correct answer.

    Explanation

    Reducing assist at higher road speed preserves meaningful steering feel and prevents the vehicle from feeling over-assisted or twitchy on the highway. The strategy is about driver feedback and directional stability, not about electrical supply or sensor calibration.

  35. Question 35Steering Systems

    Toe-out on turns is designed so that:

    1. the inner wheel steers a sharper angle than the outer Correct answer.
    2. the outer wheel steers a sharper angle than the inner
    3. both front wheels stay parallel through the turn
    4. the rear wheels steer opposite the front wheels

    Explanation

    Toe-out on turns, or Ackermann geometry, angles the steering arms so the inner wheel follows a tighter radius than the outer wheel. This allows both front tires to roll through the turn without scrubbing sideways.

  36. Question 36Steering Systems

    A technician is checking a parallelogram steering linkage for wear. Which method best reveals a worn idler arm bushing?

    1. Measure the distance between the two tie rod ends
    2. Pry the idler arm up and down and measure the movement Correct answer.
    3. Twist the idler arm around the center link axis
    4. Turn the wheel 90 degrees and watch the pitman arm

    Explanation

    Idler arm wear is checked by loading the arm vertically, usually with a pry bar, and measuring movement at the arm end against specification. Movement beyond specification means the bushing or arm must be replaced.

  37. Question 37Steering Systems

    After a power steering pump replacement, the system is refilled. Which procedure best removes trapped air?

    1. Cap the reservoir and drive the vehicle at highway speed
    2. Raise the front wheels and turn the wheel lock to lock at idle Correct answer.
    3. Drain and refill the system without starting the engine
    4. Hold the engine at 2500 rpm and hold the steering at full lock for one minute

    Explanation

    Air is purged by cycling the steering from lock to lock with the engine idling and the reservoir open, with the front wheels off the ground to reduce load. Fluid level is topped up during the process and rechecked once the air is gone.

  38. Question 38Steering Systems

    A vehicle has memory steer: after a turn it continues to pull in the direction of that turn until the driver corrects it. Which is the most likely cause?

    1. Incorrect total toe setting
    2. Excessive positive caster on both sides
    3. Worn inner tie rod sockets
    4. A binding strut bearing or upper mount Correct answer.

    Explanation

    Memory steer means something in the steering or strut mount is binding and preventing the wheels from returning freely once the turn is completed. A binding strut bearing or upper mount is the classic cause of this complaint.

  39. Question 39Steering Systems

    A recirculating-ball steering gear is adjusted with excessive worm bearing preload. Which symptom would this produce?

    1. High steering effort and poor return to center Correct answer.
    2. A vibration felt only at highway speed
    3. Uneven tire wear across both front tires
    4. Loose, wandering steering with excess free play at the wheel

    Explanation

    Worm bearing preload is set at the input shaft, and too much preload makes the gear bind, so effort is high and the wheel will not return to center freely. The tightness remains even with the pitman arm disconnected, which separates it from binding in the linkage.

  40. Question 40Steering Systems

    An electric power steering system intermittently drops assist and sets a torque sensor code. Which is the most likely cause?

    1. Low tire pressure on one front tire
    2. High resistance in the torque sensor circuit Correct answer.
    3. A worn inner tie rod socket
    4. Excessive positive caster

    Explanation

    The control module needs a continuous, accurate torque sensor signal to command assist, so a poor connection, chafed wire, or high resistance in that circuit can cause intermittent assist loss and a stored torque sensor code. Mechanical and alignment conditions do not set this code.

  41. Question 41Suspension Systems

    What is the primary function of a shock absorber or strut damper in a suspension system?

    1. Control spring oscillation by converting motion to heat Correct answer.
    2. Maintain alignment angles as the suspension moves
    3. Keep the tire flat on the road during cornering
    4. Support vehicle weight and establish ride height

    Explanation

    A damper converts the kinetic energy of suspension movement into heat through hydraulic fluid forced through valving, which limits how many times and how far the springs oscillate. It does not carry vehicle weight or set ride height; the springs do that.

  42. Question 42Suspension Systems

    A vehicle sits noticeably lower at the left rear than at the right rear, and the left rear coil spring is visibly collapsed and weaker than the right. Which repair is correct?

    1. Replace the left rear coil spring Correct answer.
    2. Replace the rear stabilizer bar links
    3. Replace the left rear lower control arm
    4. Replace the left rear shock absorber

    Explanation

    Ride height at a corner is set by the spring, so a collapsed spring that lets that corner sag must be replaced. A weak damper affects ride control but will not hold a corner of the vehicle down at rest.

  43. Question 43Suspension Systems

    What is the primary function of a ball joint in a suspension system?

    1. Attach the wheel hub to the axle shaft
    2. Dampen road vibration before it reaches the vehicle body
    3. Limit suspension travel at the end of the rebound stroke
    4. Act as a pivot between the control arm and knuckle Correct answer.

    Explanation

    A ball joint is a spherical pivot that lets the steering knuckle move through jounce, rebound, and steering while holding the control arm to the knuckle. The stud and socket design allows motion in multiple planes, which a simple bushing or clevis cannot provide.

  44. Question 44Suspension Systems

    Which observation during a suspension inspection most directly points to a worn damper?

    1. The body keeps bouncing after a push-down test Correct answer.
    2. The steering wheel shimmies at parking lot speeds
    3. The tire tread shows feathered edges across the face
    4. The vehicle pulls to one side only during braking

    Explanation

    A push-down test that produces more than one or two rebound cycles shows the damper is not controlling spring energy. Fluid leakage on the damper body and cupped tire wear support this diagnosis.

  45. Question 45Suspension Systems

    What is the purpose of a stabilizer bar in a suspension system?

    1. Vary caster as the suspension compresses
    2. Reduce body roll during cornering Correct answer.
    3. Absorb engine torque reaction during acceleration
    4. Increase load capacity when the vehicle is loaded

    Explanation

    A stabilizer bar links the two sides of a suspension through torsion; when one side compresses, the bar twists and resists further roll. It also affects the balance of grip between the front and rear axles.

  46. Question 46Suspension Systems

    Which statement about a MacPherson strut suspension is correct?

    1. It requires upper and lower control arms to locate the knuckle
    2. It cannot be removed without dropping the steering rack
    3. It combines the spring and damper in one locating unit Correct answer.
    4. It is used only on rear suspensions with a solid axle

    Explanation

    In a MacPherson design, the strut assembly carries the coil spring and damper together and its upper mount also serves as an attachment point that positions the knuckle. Only a lower control arm is used, which is what makes the layout compact.

  47. Question 47Suspension Systems

    A toe setting on an alignment machine is expressed as the difference between which two measurements?

    1. The distance between the tires measured at front and rear Correct answer.
    2. The tilt of the wheel from vertical viewed from the front
    3. The forward or rearward tilt of the steering axis
    4. The angle between the steering axis and the wheel centerline

    Explanation

    Toe compares the track dimension measured across the front of the tires with the dimension across the rear of the tires; the difference is expressed in degrees or as a linear distance. Toe-in means the front dimension is smaller than the rear dimension.

  48. Question 48Suspension Systems

    What does turning the adjusting bolt on a torsion bar suspension change?

    1. The spring rate of the torsion bar
    2. The ride height of the vehicle Correct answer.
    3. The camber angle at that wheel
    4. The rebound valving of the shock absorber

    Explanation

    The adjusting bolt rotates the anchor of the torsion bar, changing how much the bar is pre-twisted and therefore how much load it applies to the control arm. Changing that preload raises or lowers the corner of the vehicle.

  49. Question 49Suspension Systems

    Adding positive caster to a front suspension generally produces which effect?

    1. A change in the thrust angle of the rear axle
    2. Better straight-ahead stability with higher steering effort Correct answer.
    3. Reduced steering effort with noticeably slower return to center
    4. Accelerated wear along the inner edge of both front tires

    Explanation

    Positive caster places the tire contact patch behind the steering axis, so the wheel tends to trail and self-center, improving high-speed stability. The trade-off is heavier steering effort and more steering-axis load.

  50. Question 50Suspension Systems

    A front tire shows accelerated wear on its outer shoulder while the inner shoulder looks normal. Which alignment condition is most likely responsible?

    1. Excessive negative caster
    2. Excessive positive camber Correct answer.
    3. Excessive toe-out on the front axle
    4. Excessive rear thrust angle

    Explanation

    Positive camber tilts the top of the wheel outward, which loads the outer shoulder and wears it faster than the rest of the tread. Toe wear typically produces a feathered pattern across the whole tread face rather than shoulder-specific wear.

  51. Question 51Suspension Systems

    On a strut suspension where the coil spring seats on the lower control arm, how should the lower ball joint be checked for looseness?

    1. On a frame-contact lift with the wheels hanging free
    2. With the coil spring removed and the arm on a jack
    3. At normal ride height with a helper rocking the tire Correct answer.
    4. With the lower control arm hanging at full rebound

    Explanation

    When the spring loads the lower control arm, the ball joint is in its normal working position and clearance shows up as vertical play between the stud and housing. Checking with the suspension hanging unloads the joint and can hide or falsely show play.

  52. Question 52Suspension Systems

    A customer reports a clunk over bumps, and inspection shows worn, loose sockets in the front stabilizer bar links. What is the correct repair?

    1. Replace the steering rack
    2. Replace both front struts
    3. Replace the lower ball joints
    4. Replace the stabilizer bar link Correct answer.

    Explanation

    Loose sockets in a stabilizer link allow the bar to knock against the link ends as the suspension moves, producing a clunk over bumps. The link is the failed part and replacement cures the noise.

  53. Question 53Suspension Systems

    What is the accepted repair when the main leaf of a multi-leaf spring pack is cracked?

    1. Weld the crack and reinstall the spring
    2. Install an add-a-leaf kit to restore capacity
    3. Replace only the cracked main leaf and reuse the pack
    4. Replace the complete spring assembly Correct answer.

    Explanation

    Leaf springs are matched assemblies; the leaves are formed and tempered to work together, and the center bolt and clips hold a specific stack. Welding a spring leaf destroys its temper, and installing only part of a new pack changes rate and load capacity.

  54. Question 54Suspension Systems

    A vehicle wanders on the road and clunks over bumps; inspection shows a torn, separated lower control arm bushing. What is the correct repair?

    1. Replace the front struts
    2. Increase positive caster to compensate
    3. Replace the stabilizer bar
    4. Replace the worn control arm or bushing Correct answer.

    Explanation

    A separated control arm bushing lets the arm shift under load, changing alignment angles and producing wander and clunking. The failed bushing or the control arm assembly that carries it must be replaced.

  55. Question 55Suspension Systems

    A growl is heard from the front of a vehicle and becomes louder in a left turn and quieter in a right turn. Which component is most likely at fault?

    1. Right front wheel bearing Correct answer.
    2. Left front wheel bearing
    3. Left front outer CV joint
    4. Right front strut assembly

    Explanation

    Turning left shifts the vehicle's weight onto the right side, increasing load on the right front bearing and making a worn bearing growl louder. The noise quiets in a right turn when that bearing is unloaded.

  56. Question 56Suspension Systems

    One side of the rear axle is toed out of specification, so the rear axle no longer points straight ahead relative to the vehicle centerline. Which alignment term describes this condition?

    1. Thrust angle Correct answer.
    2. Toe-out on turns
    3. Included angle
    4. Steering axis inclination

    Explanation

    Thrust angle is the angle between the rear axle centerline and the geometric centerline of the vehicle. When it is not near zero, the vehicle dog-tracks and the steering wheel sits off center going straight.

  57. Question 57Suspension Systems

    What is the term for toe change that occurs as the suspension moves up and down through its travel?

    1. Memory steer
    2. Torque steer
    3. Bump steer Correct answer.
    4. Returnability

    Explanation

    Bump steer results from the tie rod arc not matching the control arm arc, so the wheel steers itself as the suspension compresses or extends. It is corrected by setting the tie rod inner pivot height properly, often with a bump steer kit.

  58. Question 58Suspension Systems

    A technician cuts one active coil from a linear-rate coil spring to lower the ride height. What happens to the spring rate?

    1. It decreases
    2. It increases Correct answer.
    3. It remains unchanged
    4. It becomes progressive instead of linear

    Explanation

    Rate is load divided by deflection; with fewer active coils, each coil must twist more per unit of travel, so the spring becomes stiffer. Cutting coils also reduces installed height and may cause the spring to come loose at full rebound.

  59. Question 59Suspension Systems

    Which precaution is required when disassembling a MacPherson strut assembly to replace the damper or upper mount?

    1. Loosen the upper mount nut with the weight on the suspension
    2. Support the knuckle on a jack and let the strut hang
    3. Heat the spring with a torch to relieve its tension
    4. Compress the spring before loosening the upper mount nut Correct answer.

    Explanation

    The coil spring stores a large amount of energy even with the strut removed from the vehicle, so it must be captured with a proper spring compressor before the upper mount nut is released. Releasing the nut without compressing the spring can allow the mount and spring to fly apart.

  60. Question 60Suspension Systems

    Which component tells the air suspension control module what ride height to maintain?

    1. The air compressor
    2. The pressure relief valve
    3. The air spring solenoid valve
    4. The height sensor Correct answer.

    Explanation

    Height sensors report suspension position to the control module, which then commands the compressor or the exhaust valve to raise or lower the vehicle. Without an accurate height signal, the system cannot regulate ride height.

  61. Question 61Suspension Systems

    A front suspension shows −1.5 degrees camber and 8.0 degrees steering axis inclination on the left, and +0.2 degrees camber and 8.1 degrees steering axis inclination on the right. Camber is not adjustable. What is the best conclusion?

    1. The rear axle has excessive thrust angle
    2. A bent knuckle or strut on the side with the smaller included angle Correct answer.
    3. A bent knuckle or strut on the side with the larger included angle
    4. Both front wheel bearings have excessive play

    Explanation

    Included angle is camber plus SAI, which gives roughly 6.5 degrees on the left and 8.3 degrees on the right. Included angle is not adjustable and should match side to side within about half a degree, so the large difference indicates a bent knuckle or strut on the side with the smaller value.

  62. Question 62Suspension Systems

    After installing new lower control arm bushings, at what point should the pivot bolts be tightened to full torque?

    1. With the control arm resting on the bump stop
    2. With the control arm hanging at full rebound
    3. Before the coil spring is installed in the vehicle
    4. At normal ride height with the full weight on it Correct answer.

    Explanation

    Rubber bushings bond to their inner and outer sleeves and twist as the arm moves, so they must be tightened at normal ride height to avoid preloading them. A preloaded bushing shortens bushing life and can alter ride height and alignment.

  63. Question 63Suspension Systems

    After a turn, the steering wheel stays off center until the driver pulls it straight, and all alignment angles are within specification. Which cause is most likely?

    1. Excessive positive caster on the front axle
    2. A worn inner tie rod socket
    3. A binding strut upper bearing or mount Correct answer.
    4. Incorrect rear thrust angle

    Explanation

    Memory steer happens when a component in the steering pivot path binds, so the wheel cannot self-center after the turn is completed. A dry or collapsed strut upper bearing is a common cause, and it also often produces a popping noise when turning.

  64. Question 64Suspension Systems

    Front ride height measures well below specification on a short-long arm suspension, and camber is out of range. What should the technician do first?

    1. Replace the tires and recheck camber
    2. Adjust camber with shims and release the vehicle
    3. Set toe only and note the camber reading
    4. Repair the ride height first, then set the alignment Correct answer.

    Explanation

    Ride height is the foundation of the alignment because control arm angle determines camber and often caster as the suspension moves. If ride height is wrong, camber cannot be adjusted accurately, so the spring, sagging components, or load condition must be corrected before alignment.

  65. Question 65Suspension Systems

    A vehicle pulls to the right, but all alignment angles are within specification. After swapping the two front tires, the pull changes to the left. What is the most likely cause?

    1. A worn right front wheel bearing
    2. Tire conicity causing a radial tire pull Correct answer.
    3. A dragging right front brake caliper
    4. Excessive positive caster on the right side

    Explanation

    Conicity is a built-in lateral force in a tire caused by its internal construction, and it pushes the vehicle toward one side. The pull following the tire when the positions are swapped confirms the tire rather than the alignment or brakes is the cause.

  66. Question 66Suspension Systems

    What is the primary function of the shock absorbers (dampers) in a suspension system?

    1. Keep the tires square to the road in a corner
    2. Support vehicle weight and establish ride height
    3. Convert suspension motion into heat Correct answer.
    4. Locate the wheel fore-and-aft under braking

    Explanation

    Dampers control the rate at which the spring releases and absorbs its stored energy by forcing hydraulic fluid through orifices, which turns suspension motion into heat. They do not carry the vehicle's weight or locate the wheel; those jobs belong to the springs and the linkage.

  67. Question 67Suspension Systems

    A front wheel has positive camber. How is the top of that wheel positioned?

    1. Tilted outward, away from the vehicle Correct answer.
    2. Tilted inward toward the vehicle centerline
    3. Tilted rearward relative to the steering axis
    4. Tilted forward relative to the steering axis

    Explanation

    Camber is the tilt of the wheel as viewed from the front of the vehicle. Positive camber means the top of the wheel leans outward, away from the centerline, while negative camber means the top leans inward. Forward or rearward tilt of the steering axis is caster, not camber.

  68. Question 68Suspension Systems

    What is the purpose of the stabilizer bar (anti-roll bar) on a vehicle?

    1. It keeps the wheel upright as the control arm moves
    2. It holds the vehicle at a fixed ride height when loaded
    3. It damps oscillation of the coil springs after a bump
    4. It links both sides to resist body roll in a turn Correct answer.

    Explanation

    A stabilizer bar is a torsion spring connected to both sides of the suspension. When one side compresses in a turn, the bar twists and adds resistance at the outside wheel, reducing body roll. It does not carry weight, hold camber, or damp spring oscillation.

  69. Question 69Suspension Systems

    What is the purpose of the center bolt in a multi-leaf spring pack?

    1. It lets the spring eye pivot on the shackle pin
    2. It sets the amount of arch built into the spring pack
    3. It provides a lubrication passage between the leaves
    4. It clamps the leaves together and locates the axle Correct answer.

    Explanation

    The center bolt runs through the assembled leaves, holds them tightly together, and its head seats in the axle mounting pad so the axle stays in its correct fore-aft position. Arch is formed by the curvature of the individual leaves, and lubrication is provided by liners or tip pads.

  70. Question 70Suspension Systems

    Both front wheels are set to the correct toe, but the toe-out on turns reading is out of specification on one side. Which is the most likely cause?

    1. Too much positive caster on that side
    2. Incorrect toe setting at the tie rods
    3. A worn idler arm bushing
    4. A bent steering arm on the knuckle Correct answer.

    Explanation

    Toe-out on turns is built into the angle of the steering arms so the inner wheel turns tighter than the outer wheel. Because it is a machined geometry angle, it cannot be changed by adjusting the tie rods; only a bent or damaged steering arm or knuckle alters it.

  71. Question 71Suspension Systems

    The idler arm on a parallelogram steering system has excessive up-and-down movement at its frame-mounted pivot. Which condition will this most likely cause?

    1. Cupping wear across the rear tires
    2. A bind felt at one point in the steering wheel travel
    3. Increased positive camber on the right front wheel
    4. Excessive steering wheel free play and wander Correct answer.

    Explanation

    The idler arm supports the end of the relay rod opposite the pitman arm. When its pivot is worn, the relay rod can move vertically, so the steering wheel must travel before the wheels respond, creating lost motion and wander.

  72. Question 72Suspension Systems

    The tension (strut) rod bushing at the front of a lower control arm is worn and allows fore-aft movement. Which alignment angle is most directly affected?

    1. Thrust angle
    2. Camber
    3. Caster Correct answer.
    4. Toe

    Explanation

    The tension rod controls fore-and-aft location of the lower control arm. If the bushing allows the arm to move front to back, the lower ball joint shifts relative to the upper pivot and caster changes, often unequally side to side.

  73. Question 73Suspension Systems

    What is the function of the jounce bumper (bump stop) in a suspension system?

    1. It limits downward wheel travel when the vehicle is raised
    2. It retains the spring when the suspension is at full rebound
    3. It seals the damper rod and keeps dirt out of the housing
    4. It cushions the suspension at full compression Correct answer.

    Explanation

    The jounce bumper is a rubber or urethane cushion that contacts the frame or strut body near the end of upward suspension travel. It prevents metal-to-metal bottoming and progressively adds spring rate as it compresses.

  74. Question 74Suspension Systems

    A vehicle's ride becomes floaty and the dampers fade after several miles of rough road, then recover after the vehicle cools. Which is the most likely cause?

    1. Air mixed into the damper fluid Correct answer.
    2. Worn control arm bushings allowing toe change
    3. Weak coil springs sagging under load
    4. A seized jounce bumper limiting travel

    Explanation

    When damper fluid is aerated, the air and oil mixture can compress through the orifices instead of being forced through them, so damping force drops off until the air settles out. Fluid aeration can come from low fluid, gas intrusion, or severe use, and the symptom follows temperature and time.

  75. Question 75Suspension Systems

    A vehicle sits noticeably lower at the left front corner, and left front camber is out of range. The left front coil spring is found broken at one of its end coils. Which is the correct repair?

    1. Replace both front springs Correct answer.
    2. Heat and re-arch the spring to restore height
    3. Install a spacer to restore ride height
    4. Adjust camber back to specification

    Explanation

    A broken spring can no longer support its share of the load, so that corner drops and camber changes as a result. The spring must be replaced, and most manufacturers specify replacing both sides so that spring rate and ride height stay matched.

  76. Question 76Suspension Systems

    A front wheel on a rear-wheel-drive vehicle is checked with the tire installed. Grasping the tire at 12 and 6 o'clock produces noticeable play, while grasping at 3 and 9 o'clock produces almost none. What does this indicate?

    1. Worn control arm bushings
    2. Wheel bearing end play Correct answer.
    3. A worn upper strut mount
    4. A loose tie rod end on that side

    Explanation

    On a non-driven front wheel, end play in the wheel bearing shows up as top-to-bottom movement at the tire. Side-to-side movement at 3 and 9 o'clock points instead to steering linkage such as tie rod ends, the idler arm, or the steering gear.

  77. Question 77Suspension Systems

    A front-wheel-drive car tracks straight while cruising but pulls to the right only during hard acceleration, then straightens when the throttle is released. All alignment angles are within specification. Which is the most likely cause?

    1. A dragging right front brake caliper
    2. A worn right front lower ball joint
    3. Torque steer from unequal half shaft angles Correct answer.
    4. Excessive positive caster on the left side

    Explanation

    Torque steer occurs when engine torque twists the steering because the two half shafts differ in length or angularity, so the effect appears only under acceleration. A caster or ball joint problem or a dragging brake would affect the vehicle during steady-state driving as well.

  78. Question 78Suspension Systems

    A solid rear axle is located laterally by a single track bar (Panhard rod) that is horizontal at design ride height. As the body rolls in a turn and the axle moves upward on one side, what happens?

    1. The axle rotates about its center and changes pinion angle
    2. The axle stays perfectly centered because the bar is fixed in length
    3. The axle shifts sideways slightly Correct answer.
    4. The axle moves rearward only on the compressed side

    Explanation

    A track bar is a fixed-length link, so as the axle moves vertically the bar pivots and its end sweeps through an arc. This swings the axle sideways a small amount, which is why the bar is set horizontal at design ride height to keep that lateral movement minimal in normal travel.

  79. Question 79Suspension Systems

    A technician installs longer-than-stock shackles on the rear leaf springs to raise the back of a vehicle. Which statement best describes the result?

    1. The spring eye binds, making the rear suspension rigid
    2. Ride height rises slightly and pinion angle changes Correct answer.
    3. Spring rate increases because the shackle adds leverage to the spring
    4. Ride height is unchanged because the spring arch is unchanged

    Explanation

    A longer shackle changes the angle at which the rear spring eye sits, lifting the frame a small amount, and it also rotates the axle housing on its spring pads, altering pinion angle. Shackle length does not change the rate built into the leaf pack.

  80. Question 80Suspension Systems

    Two technicians are discussing steering linkage inspection. Technician A says the play check is done with the engine off and the steering wheel gently rocked until the tires begin to move. Technician B says the dry park check is done with the weight on the tires and an assistant turning the wheel while the technician watches the joints. Who is correct?

    1. Technician A only
    2. Technician B only
    3. Both technicians Correct answer.
    4. Neither technician

    Explanation

    The play check measures lost motion: the engine is off and the wheel is rocked by hand until the tires respond, with the free play compared to specification. The dry park check is performed with the weight on the tires and an assistant turning the wheel so each joint can be observed for looseness under real load.

  81. Question 81Wheel Alignment

    Viewed from the front of the vehicle, camber is the angle between the wheel's centerline and:

    1. the steering axis
    2. the vehicle centerline
    3. the rear thrust line
    4. a true vertical line Correct answer.

    Explanation

    Camber is a front-view angle measured from true vertical. Tilting the top of the wheel outward is positive camber and tilting it inward is negative camber.

  82. Question 82Wheel Alignment

    A wheel with positive camber has its top tilted:

    1. rearward of the steering axis
    2. forward of the steering axis
    3. outward away from the engine Correct answer.
    4. inward toward the engine

    Explanation

    Positive camber tilts the top of the wheel outward, away from the vehicle body. Negative camber tilts the top inward toward the body.

  83. Question 83Wheel Alignment

    Toe-in means that the front of the tires are:

    1. tilted inward at the top
    2. farther apart than the rear of the tires
    3. parallel to the thrust line
    4. closer together than the rear of the tires Correct answer.

    Explanation

    Toe-in means the leading edges of the tires point toward each other, so the front of the tires are closer together than the rear. Toe-out is the opposite condition.

  84. Question 84Wheel Alignment

    Caster is the forward or rearward tilt of the steering axis and is measured:

    1. at the tire contact patch
    2. in the front view
    3. with the wheels turned 90 degrees
    4. in the side view Correct answer.

    Explanation

    Caster is a side-view angle formed by the steering axis and true vertical. It is what gives the steering its self-centering force.

  85. Question 85Wheel Alignment

    Excessive toe on the front wheels typically produces which tread wear pattern?

    1. A smooth band around the center of the tread
    2. Cracks in the sidewall
    3. Feathered edges on the tread ribs Correct answer.
    4. Even wear across the whole tread

    Explanation

    Toe causes each tread rib to scrub sideways, wearing one edge of the rib and leaving the other sharp, which is the feathered pattern. Running a hand across the tread in both directions reveals it.

  86. Question 86Wheel Alignment

    Excessive negative camber on one front wheel will most likely cause:

    1. wear on the outer edge of that tire
    2. a feathered tread pattern
    3. wear on the inner edge of that tire Correct answer.
    4. cupping across the tread

    Explanation

    Negative camber leans the top of the wheel inward, loading the inner edge of the tire, so that edge wears fastest. Positive camber produces the opposite wear pattern.

  87. Question 87Wheel Alignment

    While the front toe is being adjusted, the steering wheel should be:

    1. removed to prevent airbag damage
    2. held in the straight-ahead position Correct answer.
    3. left free to rotate with the tie rods
    4. turned 90 degrees to load the gear

    Explanation

    The wheel must be locked or held in the straight-ahead position so the total toe is split evenly between the two sides. Otherwise the toe setting will be correct but the steering wheel will sit off center.

  88. Question 88Wheel Alignment

    Thrust angle is the angle between the vehicle's geometric centerline and:

    1. the front toe bisector
    2. the rear axle's thrust line Correct answer.
    3. the camber line
    4. the steering axis

    Explanation

    Thrust angle compares the direction the rear axle points with the geometric centerline of the vehicle. A non-zero thrust angle makes the vehicle dog-track and forces the driver to hold the wheel off center.

  89. Question 89Wheel Alignment

    On the left front, camber is out of specification and the included angle is also out of specification. The technician should conclude that:

    1. only camber needs to be adjusted
    2. the tire has shifted belts
    3. the caster setting is too positive
    4. a bent knuckle or strut is likely Correct answer.

    Explanation

    Included angle is camber plus SAI, and it changes only when a component such as the knuckle, spindle, or strut is bent. Ride height changes and normal adjustments move camber and SAI together, leaving included angle unchanged.

  90. Question 90Wheel Alignment

    A vehicle with too little positive caster will most likely exhibit:

    1. excessive inner-edge tire wear
    2. heavy steering effort at low speed
    3. poor straight-line stability and weak self-centering Correct answer.
    4. a steering wheel that is off center

    Explanation

    Caster produces self-aligning torque, so too little of it makes the vehicle wander at speed and slow to return to center after a turn. Too much caster shows up as high steering effort instead.

  91. Question 91Wheel Alignment

    Memory steer, where the vehicle continues to turn after the steering wheel is released, is most likely caused by:

    1. too much positive caster on both sides
    2. binding in a strut bearing or a tight ball joint Correct answer.
    3. low tire pressure on one front tire
    4. a worn idler arm bushing with excessive play

    Explanation

    Memory steer occurs when something in the steering or suspension binds and prevents the wheel from returning. Common causes are a dry or binding strut bearing, a tight ball joint, or a binding steering shaft joint.

  92. Question 92Wheel Alignment

    Torque steer on a front-wheel-drive vehicle is best described as:

    1. slow return of the steering wheel after a turn
    2. a vibration felt through the steering wheel
    3. a steady pull that is present at all vehicle speeds
    4. a change in steering direction during acceleration Correct answer.

    Explanation

    Torque steer is a change in heading under acceleration caused by unequal drive torque at the front wheels. Unequal-length halfshafts or different halfshaft angles are typical causes.

  93. Question 93Wheel Alignment

    Bump steer is caused by:

    1. tie rod inner pivot geometry not matching the control arm arcs Correct answer.
    2. an incorrect rear thrust angle
    3. a worn front wheel bearing
    4. too much positive caster on one side

    Explanation

    Bump steer is a change in toe as the suspension travels, which happens when the tie rod's arc does not match the control arm's arc. Incorrect ride height or a bent steering arm can create it.

  94. Question 94Wheel Alignment

    Toe-out on turns, also called turning angle, is designed so that:

    1. the inner wheel turns a sharper angle than the outer wheel Correct answer.
    2. the rear wheels steer opposite the front wheels
    3. the outer wheel turns a sharper angle than the inner wheel
    4. both front wheels turn the same amount

    Explanation

    Ackermann geometry makes the inner wheel follow a tighter radius, so it must turn sharper than the outer wheel. This geometry is built into the angle of the steering arms.

  95. Question 95Wheel Alignment

    A rear thrust angle of 0.8 degrees on a vehicle with a solid rear axle will most likely cause:

    1. the steering wheel to sit off center and the vehicle to dog-track Correct answer.
    2. excessive inner-edge wear on the rear tires
    3. the front tires to feather
    4. a vibration at highway speed

    Explanation

    When the rear axle is not square to the body, the whole vehicle travels at an angle to its centerline. The driver must hold the wheel off center to go straight, and the vehicle appears to dog-track.

  96. Question 96Wheel Alignment

    Setback is best defined as:

    1. the difference in camber from side to side
    2. one front wheel set rearward of the other Correct answer.
    3. the rearward tilt of the steering axis
    4. the angle between the rear axle and centerline

    Explanation

    Setback exists when one front wheel is farther back than the other, which changes the wheelbase side to side. It can be caused by frame damage or a shifted cradle and may produce a pull.

  97. Question 97Wheel Alignment

    Scrub radius is measured at the road surface between the tire's contact patch center and which point?

    1. the vehicle's geometric centerline
    2. the inner tie rod pivot point
    3. the center of the wheel rim
    4. the steering axis intersection Correct answer.

    Explanation

    Scrub radius is the distance on the ground between where the steering axis meets the road and the center of the tire contact patch. It influences steering effort, road feel, and brake pull sensitivity.

  98. Question 98Wheel Alignment

    Ride height must be checked and corrected before alignment angles are measured because:

    1. alignment machines cannot read angles on a low vehicle
    2. toe settings are independent of suspension position
    3. tire pressure changes with vehicle height
    4. camber and caster change as the suspension moves through travel Correct answer.

    Explanation

    Alignment specifications are published for the designed ride height, and camber and caster change as the suspension moves up or down. Measuring at the wrong height produces readings that do not reflect the real geometry.

  99. Question 99Wheel Alignment

    On a short-long arm suspension using shims at the upper control arm pivot shaft, adding shims at the rear of the shaft mainly changes:

    1. caster Correct answer.
    2. thrust angle
    3. toe
    4. camber

    Explanation

    Shims at the rear pivot move that end of the shaft in or out, which rotates the control arm fore-and-aft and tilts the steering axis. That fore-and-aft tilt is caster.

  100. Question 100Wheel Alignment

    A vehicle pulls to the right. After the two front tires are swapped side to side, the pull changes to the left. This indicates:

    1. a dragging right front brake
    2. a bent strut on the right side
    3. excessive positive caster on the left side
    4. tire conicity or a shifted belt Correct answer.

    Explanation

    If the pull follows the tire when the tires are swapped, the tire is the cause; conicity or a shifted belt makes a tire push sideways like a cone. If the pull stays on the same side, look at alignment or brakes.

  101. Question 101Wheel Alignment

    Left front readings are camber +1.2 degrees and SAI 13.4 degrees. The manufacturer lists included angle as 16.2 degrees plus or minus 0.5 degree. The most likely conclusion is:

    1. a bent knuckle or strut is likely Correct answer.
    2. only camber needs to be adjusted
    3. SAI cannot be read with the wheels installed
    4. the caster setting is too positive

    Explanation

    Included angle is camber plus SAI, so 1.2 plus 13.4 equals 14.6 degrees, below the 15.7 degree minimum. Because ride height and normal adjustments move camber and SAI together, an out-of-range included angle points to a bent knuckle, spindle, or strut.

  102. Question 102Wheel Alignment

    After front suspension repairs, camber and caster on both sides cannot be brought into range. On a unitized-body vehicle the most likely cause is:

    1. an incorrect rear thrust angle
    2. worn stabilizer bar bushings
    3. a cradle that is misaligned on the body Correct answer.
    4. front tires that are overinflated

    Explanation

    Camber and caster are set relative to the body, so a front cradle that is shifted moves the suspension mounting points and can leave no adjustment range. Realigning the cradle restores the original geometry.

  103. Question 103Wheel Alignment

    Installing wheels with a different offset from the original wheels directly changes which alignment-related dimension?

    1. caster
    2. included angle
    3. toe-out on turns
    4. scrub radius Correct answer.

    Explanation

    Offset moves the tire contact patch in or out relative to the steering axis, so scrub radius changes and steering feel, brake pull sensitivity, and wheel bearing loading can change. The steering axis itself is unchanged.

  104. Question 104Wheel Alignment

    Total front toe is correct, but the steering wheel sits off center to the left. To correct this without changing total toe, the technician should:

    1. shorten one tie rod and lengthen the other equally Correct answer.
    2. lengthen both outer tie rods by an equal number of turns
    3. shorten both outer tie rods by an equal number of turns
    4. adjust only the left tie rod until the wheel is centered

    Explanation

    Turning one tie rod in and the other out by the same amount rotates the steering gear and wheel relative to the tires while leaving total toe unchanged. This is the standard way to re-center the wheel after toe has been set.

  105. Question 105Wheel Alignment

    A vehicle has 1.5 degrees of cross-caster with every other angle within specification. The most likely customer complaint is:

    1. a steady lead or pull to one side Correct answer.
    2. cupped front tires
    3. a hard brake pedal
    4. a shimmy at highway speed

    Explanation

    Unequal caster side to side creates unequal self-aligning force, so the vehicle leads or pulls toward one side even when camber and toe are correct. A caster split is a common cause of a pull that does not respond to tire rotation.

  106. Question 106Wheel Alignment

    Excessive front toe, either inward or outward, will most likely produce which tire wear pattern?

    1. Flat spots around the circumference
    2. Feathered edges across the tread Correct answer.
    3. Cupping on the outer shoulder
    4. A smooth band in the center

    Explanation

    Toe causes the tire to scrub sideways, so the tread ribs develop a feather edge with one side sharp and the other rounded. Camber wear is one-shouldered, while inflation wear is centered or on both shoulders.

  107. Question 107Wheel Alignment

    Camber is the angle between the wheel's center plane and which reference?

    1. Vertical, viewed from the front Correct answer.
    2. The road surface in side view
    3. The vehicle centerline in top view
    4. The steering axis in side view

    Explanation

    Camber is the inward or outward tilt of the top of the wheel measured from vertical in the front or rear view. Toe uses the top view, and caster uses the side view.

  108. Question 108Wheel Alignment

    Caster is measured in which view of the vehicle?

    1. Front view
    2. Top view
    3. Side view Correct answer.
    4. Rear view

    Explanation

    Caster is the forward or rearward tilt of the steering axis and is measured in the side view. Camber is viewed from the front or rear, and toe is viewed from the top.

  109. Question 109Wheel Alignment

    Before measuring wheel alignment angles, which condition should be corrected first?

    1. Rear thrust angle out of range
    2. Low tire pressure or mismatched tires Correct answer.
    3. Front toe that is out of range
    4. A steering wheel that sits off center

    Explanation

    Tire inflation and tire size affect ride height and rolling radius, so they must be correct before any alignment readings are trusted. Toe, steering wheel centering, and thrust angle are alignment results adjusted after these pre-checks.

  110. Question 110Wheel Alignment

    On one front corner, SAI is outside specification while camber and caster can still be adjusted into range. Which is the most likely cause?

    1. A worn inner tie rod end
    2. An incorrectly set front toe
    3. A tire with excessive radial runout
    4. A bent steering knuckle or strut Correct answer.

    Explanation

    SAI is built into the steering knuckle and strut geometry and is not adjustable. An abnormal SAI on one side points to a bent or damaged steering knuckle or strut.

  111. Question 111Wheel Alignment

    On a vehicle with independent rear suspension, how is an incorrect rear thrust angle normally corrected?

    1. Rotating the front strut mounts
    2. Adjusting rear toe to set thrust line Correct answer.
    3. Replacing the rear wheel bearings
    4. Adjusting front toe equally on both sides

    Explanation

    With independent rear suspension, individual rear toe adjustments move the rear wheels and set the thrust line parallel to the vehicle centerline. Front toe does not correct rear thrust, and wheel bearings do not set toe.

  112. Question 112Wheel Alignment

    Total front toe is specified as 0.20 degree toe-in. The left front reads 0.15 degree toe-in. What should the right front reading be?

    1. 0.05 degree toe-out
    2. 0.05 degree toe-in Correct answer.
    3. 0.20 degree toe-out
    4. 0.35 degree toe-in

    Explanation

    Total toe is the sum of the individual toe readings when both are expressed with the same sign convention. Subtracting the left reading of 0.15 from the 0.20 total leaves 0.05 degree toe-in on the right.

  113. Question 113Wheel Alignment

    A front suspension has a large positive scrub radius. What is the most likely effect felt through the steering wheel?

    1. Reduced steering effort at low speed
    2. Kickback and road feel over bumps Correct answer.
    3. A strong self-centering action at all speeds
    4. Increased tire wear on the inside edge

    Explanation

    Positive scrub radius places the tire contact patch outboard of the steering axis pivot at the road, so road forces create a moment about the steering axis and are felt as kickback. Caster mainly provides self-centering, and camber drives edge wear.

  114. Question 114Wheel Alignment

    Both front wheels have excessive negative camber. Which wear pattern should be expected?

    1. Feathered wear across both front treads
    2. Wear on the inner edges of both front tires Correct answer.
    3. Wear on the outer edges of both front tires
    4. Center wear on both front tires

    Explanation

    Negative camber tilts the top of the wheel inward, loading the inner shoulder and inner tread edge. Positive camber wears the outer edges, toe causes feathering, and overinflation causes center wear.

  115. Question 115Wheel Alignment

    Increasing positive caster within the manufacturer's range will normally have which effect?

    1. It reduces steering wheel returnability
    2. It increases wear on the inner tire edges
    3. It raises steering effort and stability Correct answer.
    4. It directly changes the total toe setting

    Explanation

    Positive caster leans the steering axis rearward and adds a self-centering force as the wheels turn, improving straight-line stability while increasing steering effort. Caster is not a major tire-wear angle and does not directly set toe.

  116. Question 116Wheel Alignment

    Toe is correctly set, but toe-out on turns is out of specification on one side. Which is the most likely cause?

    1. A loose wheel bearing
    2. A bent steering arm Correct answer.
    3. Incorrect front camber
    4. A worn idler arm

    Explanation

    Toe-out on turns is determined by the angle built into the steering arms. If the turning-angle reading is wrong while toe is correct, a bent steering arm or knuckle is the likely cause.

  117. Question 117Wheel Alignment

    During an alignment, wheel runout compensation is performed mainly to correct for which condition?

    1. A rear thrust angle that is out of range
    2. A tire with low air pressure
    3. A steering wheel that is off center
    4. Wheel runout that skews the readings Correct answer.

    Explanation

    Runout compensation lets the alignment computer separate wheel and tire runout from the actual wheel plane so camber and toe readings are accurate. It does not correct tire pressure, steering wheel centering, or rear thrust angle.

  118. Question 118Wheel Alignment

    During a caster sweep at 20 degrees, camber reads +1.5 degrees with the wheel turned left and -2.5 degrees with it turned right. What is the approximate caster angle?

    1. 4.0 degrees
    2. 6.0 degrees Correct answer.
    3. 2.5 degrees
    4. 1.5 degrees

    Explanation

    Caster is approximately the camber change between the two 20-degree sweep positions multiplied by 1.5. The change is 4.0 degrees, so 4.0 times 1.5 equals 6.0 degrees.

  119. Question 119Wheel Alignment

    Rear individual toe readings are 0.30 degree toe-in on the left and 0.10 degree toe-in on the right. What is the approximate thrust angle?

    1. 0.10 degree Correct answer.
    2. 0.20 degree
    3. 0.05 degree
    4. 0.40 degree

    Explanation

    Thrust angle is half the difference between the left and right rear toe readings when they are measured from the vehicle centerline. The difference is 0.20 degree, so half of that is 0.10 degree.

  120. Question 120Wheel Alignment

    A vehicle with a solid rear axle has total rear toe of 0.50 degree and no adjustable rear toe provision. What is the most likely cause?

    1. A mis-centered steering wheel
    2. Worn rear control arm bushings
    3. Incorrect front caster
    4. A bent rear axle housing Correct answer.

    Explanation

    A solid axle has fixed rear toe geometry, so a significant rear toe error with no adjustment provision usually indicates a bent axle housing or spindle flange. Front settings and steering wheel centering cannot change rear toe.

  121. Question 121Wheels and Tires

    A tire is marked P225/60R16. What does the 225 indicate?

    1. Tread width in sixteenths of an inch
    2. Rim diameter in inches
    3. Section width in millimeters Correct answer.
    4. Sidewall height in millimeters

    Explanation

    In the P-metric size system the first number is the nominal section width in millimeters. The 60 that follows is the aspect ratio, R denotes radial construction, and 16 is the rim diameter in inches.

  122. Question 122Wheels and Tires

    The load index molded on a tire sidewall, such as 91, identifies:

    1. The tire's maximum speed in kilometers per hour
    2. The maximum load the tire can carry at its rated inflation pressure Correct answer.
    3. The number of plies used in the sidewall
    4. The maximum inflation pressure the tire can hold

    Explanation

    The load index is a code that corresponds to a maximum load in pounds or kilograms when the tire is inflated to the pressure at which that rating applies. It is a weight rating, not a pressure or a speed.

  123. Question 123Wheels and Tires

    A tire carries the speed symbol H. What maximum speed is that tire rated for?

    1. 149 mph (240 km/h)
    2. 112 mph (180 km/h)
    3. 118 mph (190 km/h)
    4. 130 mph (210 km/h) Correct answer.

    Explanation

    Speed symbols progress alphabetically from lower to higher, with H rated at 130 mph and sitting between U at 124 mph and V at 149 mph. Sustained operation above the rated speed can overheat and damage the tire.

  124. Question 124Wheels and Tires

    Tread wear indicator bars are molded into the tread grooves. Tread depth at the top of the bars is:

    1. 1/32 in (0.8 mm)
    2. 3/32 in (2.4 mm)
    3. 4/32 in (3.2 mm)
    4. 2/32 in (1.6 mm) Correct answer.

    Explanation

    The bars are 2/32 in tall, so when the tread is level with them the tire has reached the legal minimum and should be replaced. Many manufacturers recommend replacing earlier, around 4/32 in, for adequate wet traction.

  125. Question 125Wheels and Tires

    A tire shows wear concentrated in the center of the tread with the shoulders relatively untouched. The most likely cause is:

    1. Underinflation
    2. A worn wheel bearing
    3. Overinflation Correct answer.
    4. Excessive negative camber

    Explanation

    An overinflated tire bows outward in the center, so the middle ribs carry more load and wear faster than the shoulders. Underinflation produces the opposite pattern, with both shoulders worn.

  126. Question 126Wheels and Tires

    When installing a wheel, the lug nuts should be tightened:

    1. In a star or criss-cross pattern in stages to the specified torque Correct answer.
    2. By hand only, then checked after 1,000 miles
    3. With an impact wrench until the nuts stop turning
    4. In a clockwise circle, fully tightening each nut before moving to the next

    Explanation

    Tightening in a cross pattern in several steps seats the wheel squarely against the hub and prevents cocking, which can cause runout, vibration, and loosening. Final torque must be applied with a calibrated torque wrench.

  127. Question 127Wheels and Tires

    A compact temporary spare tire is normally limited to:

    1. 45 mph (70 km/h) for up to 100 miles
    2. The same speed and distance limits as a road tire
    3. 50 mph (80 km/h) and a limited distance Correct answer.
    4. 35 mph (55 km/h) with no distance limit

    Explanation

    Compact spares are smaller, lighter, and inflated to a higher pressure, so they are restricted to about 50 mph and a limited distance. They are meant to get the vehicle to a repair facility, not for normal service.

  128. Question 128Wheels and Tires

    A tire graded 400 for treadwear is compared with a tire graded 200. The 400 tire:

    1. Carries a higher speed rating
    2. Runs cooler under load
    3. Is expected to wear about twice as slowly Correct answer.
    4. Has twice the traction rating

    Explanation

    The treadwear grade is a comparative number from a government-specified test, so a 400 tire should last roughly twice as long as a 200 tire under the same conditions. Traction and temperature are separate letter grades.

  129. Question 129Wheels and Tires

    A tire is sized 225/60R16. The sidewall height is approximately:

    1. 180 mm
    2. 225 mm
    3. 135 mm Correct answer.
    4. 60 mm

    Explanation

    The aspect ratio is the sidewall height expressed as a percentage of section width, so 60 percent of 225 mm is about 135 mm. Adding two sidewalls to the 16 inch rim gives the overall diameter.

  130. Question 130Wheels and Tires

    The last four digits of a DOT tire identification number read 3522. This means the tire was manufactured during:

    1. The 22nd week of 2035
    2. The 35th week of 2022 Correct answer.
    3. The 3rd week of May 2022
    4. March 5, 2022

    Explanation

    Since 2000 the final four digits are the two-digit week followed by the two-digit year. That makes the tire a 2022 product made in the 35th week, information used to judge age along with visible cracking.

  131. Question 131Wheels and Tires

    Directional tires with a V-shaped tread pattern should be rotated:

    1. Side to side on the same axle
    2. Only after the tread wear indicators appear
    3. In a full cross pattern that includes the spare
    4. Front to rear on the same side of the vehicle Correct answer.

    Explanation

    Directional tires are built to roll in one direction, so moving them across the vehicle would reverse rotation and spoil water evacuation. Keeping them on their side and swapping front to rear preserves the intended direction.

  132. Question 132Wheels and Tires

    A tire and wheel assembly that is balanced statically but not dynamically will most likely produce:

    1. A vertical bounce that is worst at low speed
    2. A side-to-side shimmy that appears at highway speed Correct answer.
    3. A steady vibration that rises and falls with engine speed
    4. Cupping across the full tread face

    Explanation

    Static imbalance is a heavy spot that makes the assembly hop up and down. Dynamic imbalance is a couple that twists the assembly side to side about the steering axis, which shows up as a shimmy and is corrected on a two-plane balancer.

  133. Question 133Wheels and Tires

    On a hub-centric wheel, the wheel is centered on the vehicle by:

    1. A centering ring pressed into the valve stem hole
    2. The lug nuts, which pull the wheel into alignment as they are torqued
    3. The brake rotor retaining screws
    4. A machined pilot bore that fits closely over the hub flange Correct answer.

    Explanation

    Hub-centric wheels locate on a machined bore that fits the hub pilot, so the studs mainly provide clamping force. Lug-centric wheels rely on chamfered nuts to center the wheel and must be torqued in stages with the wheel off the ground.

  134. Question 134Wheels and Tires

    Wheel backspacing is measured from the:

    1. Center bore to the lug hole circle
    2. Inner bead flange to the outer bead flange
    3. Mounting surface to the inner edge of the wheel Correct answer.
    4. Wheel centerline to the outer lip

    Explanation

    Backspacing is taken with a straightedge across the inner lip and a ruler down to the mounting pad. Offset measures from the centerline to the mounting surface, so the two describe the same geometry from different references.

  135. Question 135Wheels and Tires

    A tire on a hot vehicle reads 4 psi above the placard pressure, and a technician bleeds it down to the placard value. The result is that:

    1. The tire will be overinflated once it cools
    2. The tire is correctly inflated
    3. The pressure sensor will need to be replaced
    4. The tire will be underinflated once it cools Correct answer.

    Explanation

    Pressure rises with temperature, roughly 1 psi per 10 degrees F, so a hot tire naturally reads above the cold specification. Bleeding a hot tire to the placard value leaves it below specification at ambient temperature, so pressures should only be set cold.

  136. Question 136Wheels and Tires

    Which of these tire injuries is acceptable to repair?

    1. A single 1/4 inch (6 mm) nail hole in the center of the tread Correct answer.
    2. Two punctures close together in the shoulder area
    3. A tread puncture that was reamed out to 3/8 inch
    4. A nail hole in the sidewall near the bead

    Explanation

    Industry guidelines allow repair only of injuries up to 1/4 inch located in the tread crown, using a patch-plug installed from inside the tire. Sidewall and shoulder damage cannot be repaired because the casing is structurally compromised there.

  137. Question 137Wheels and Tires

    After rotating the tires on a vehicle with a direct TPMS system, a technician should:

    1. Replace all four sensors at the same time
    2. Perform the manufacturer's sensor relearn or registration procedure Correct answer.
    3. Do nothing, because each sensor automatically reports its new corner
    4. Reduce pressure 10 psi in each tire to reset the sensors

    Explanation

    Direct systems track sensors by ID and stored position, so after rotation the positions must be updated or the display reports pressures for the wrong corner. The method varies: some use a scan tool, some a magnet, and some auto-locate during a drive cycle.

  138. Question 138Wheels and Tires

    Tread worn with a feathered or saw-toothed edge across the ribs indicates:

    1. A loose wheel bearing
    2. Overinflation
    3. Normal wear for a front-wheel-drive vehicle
    4. An incorrect toe setting Correct answer.

    Explanation

    Incorrect toe drags the tread sideways, scuffing each rib into a saw-tooth pattern you can feel by running a hand across the tread. The fix is to correct toe and rotate the tires so the pattern can wear smooth.

  139. Question 139Wheels and Tires

    Scalloped or cupped wear spots around the circumference of the tread are most likely caused by:

    1. Worn shock absorbers or struts Correct answer.
    2. Incorrect wheel nut torque
    3. Excessive negative camber
    4. Overinflation

    Explanation

    Worn dampers let the wheel bounce instead of staying planted, so the tire scrubs in a repeating scalloped pattern. Imbalance and excessive runout can create a similar pattern and should be checked at the same time.

  140. Question 140Wheels and Tires

    When replacing a tire on a wheel fitted with a snap-in TPMS sensor, the recommended practice is to:

    1. Tighten the sensor nut with an impact wrench
    2. Coat the grommet with engine oil before installing
    3. Reuse the original nut and grommet if they look clean
    4. Install a new service kit with nut, grommet or washer, valve core, and cap Correct answer.

    Explanation

    The rubber seal takes a set and the retaining nut is often a torque-to-yield design, so manufacturers call for a new service kit at each tire change. This prevents leaks and corrosion, and the specified torque should be applied with a hand tool.

  141. Question 141Wheels and Tires

    A vehicle has a highway-speed vibration that persists after a careful two-plane balance. Radial runout of the assembly is measured and found within specification for the wheel but high for the tire. The best next step is to:

    1. Replace both front tires and both wheels
    2. Add more balance weights to the inner flange
    3. Raise inflation pressure to 40 psi to seat the beads
    4. Match mount the tire to the wheel to cancel radial runout Correct answer.

    Explanation

    A vibration that survives balancing is often caused by radial force variation or a stiff spot in the tire, which a road-force balancer quantifies. Match mounting indexes the tire's high spot opposite the wheel's low spot to minimize assembled runout.

  142. Question 142Wheels and Tires

    A customer installs aftermarket wheels with 20 mm less positive offset than the original wheels. The most likely result is that the tires:

    1. Cause no change as long as the bolt pattern matches
    2. Move outward and increase the load on the wheel bearings Correct answer.
    3. Move inward and reduce the track width
    4. Reduce scrub radius and improve steering feel

    Explanation

    Reducing positive offset pushes the wheel outboard, which widens the track but lengthens the lever arm on the bearings and alters scrub radius and steering geometry. Suspension is designed around a specific offset and the resulting kingpin geometry.

  143. Question 143Wheels and Tires

    A tire has 7/32 inch of tread but its DOT date code shows it was made ten years ago, and fine cracks are visible in the sidewall. The technician should recommend that the tire be:

    1. Repaired by sealing the sidewall cracks
    2. Kept in service until the tread reaches 2/32 inch
    3. Replaced, because age and weather checking have degraded it Correct answer.
    4. Rotated to the rear axle to reduce stress

    Explanation

    Ozone, UV, and heat harden the rubber over time, so age-related cracking can make a tire unsafe even with plenty of tread. Most manufacturers call for replacement around six to ten years of age, and sidewall cracking shortens that interval.

  144. Question 144Wheels and Tires

    A wheel designed for mag-type flat seat nuts with captive washers is fitted with 60 degree conical seat nuts. The result is that:

    1. The assembly is safe if torque is increased 20 percent
    2. The nuts cannot seat properly, so the wheel may loosen or be damaged Correct answer.
    3. The nuts will self-center once the vehicle is driven
    4. Only the speed rating of the tires is affected

    Explanation

    Conical, ball, and flat seat fasteners are not interchangeable; the nut seat must match the countersink in the wheel. A mismatched seat contacts only a small area, leading to loss of clamp load, stud failure, and wheel damage.

  145. Question 145Wheels and Tires

    A light truck is fitted with LT-rated tires. The correct cold inflation pressure to use is:

    1. The vehicle tire placard value, which reflects the loads the truck carries Correct answer.
    2. Ten percent below the sidewall maximum pressure
    3. Always the maximum pressure molded on the tire sidewall
    4. The tire load index divided by the number of sidewall plies

    Explanation

    The sidewall maximum is the tire's capacity limit, not the vehicle's recommended setting. Use the placard value, or the load and inflation table when the axle load differs from the stock configuration, and check it cold.

  146. Question 146Wheels and Tires

    The load index molded into a tire's sidewall indicates the tire's:

    1. maximum permissible cold inflation pressure stamped on the casing
    2. maximum load-carrying capacity at its rated cold inflation pressure Correct answer.
    3. number of body plies used in the tread and sidewall
    4. recommended rim width range for the tire size

    Explanation

    The load index is a code number that cross-references a load table, giving the greatest mass the tire can support when inflated to the pressure at which that capacity is rated. It is not a pressure rating or a construction count. The maximum inflation pressure is shown separately, and rim width information appears in tire data books rather than as a load code.

  147. Question 147Wheels and Tires

    On a wheel with positive offset, the mounting surface is located:

    1. at an angle that matches the hub face taper
    2. exactly halfway between the two bead flanges
    3. outboard of the wheel centerline Correct answer.
    4. inboard of the wheel centerline

    Explanation

    Offset is the distance from the wheel centerline to the hub mounting surface. Positive offset places the mounting face toward the outboard side of the wheel, so the tire sits farther inboard on the vehicle. Negative offset places it toward the inboard side, and zero offset puts it on the centerline.

  148. Question 148Wheels and Tires

    The treadwear indicator bars molded into the grooves of a passenger tire become flush with the tread surface at a remaining depth of:

    1. 3/32 inch
    2. 2/32 inch Correct answer.
    3. 1/32 inch
    4. 4/32 inch

    Explanation

    Passenger and light truck tires are molded with wear bars set at 2/32 inch (about 1.6 mm), which is the federally established minimum tread depth. When the tread is level with these bars, the tire is legally worn out and must be replaced. Many shops recommend replacement earlier, but the bars themselves mark 2/32 inch.

  149. Question 149Wheels and Tires

    The tire information placard affixed to a vehicle lists:

    1. the torque specification for the wheel lug nuts
    2. the maximum cold pressure molded into the tire sidewall
    3. the vehicle manufacturer's recommended cold inflation pressures Correct answer.
    4. the tire size and speed rating only

    Explanation

    The placard gives the inflation pressures the vehicle manufacturer calculated for the original tire size to carry the vehicle's loads, along with the tire size and load index. Inflation is always set to this value when tires are cold. The pressure molded on the sidewall is a maximum for the tire, not a recommendation for the vehicle.

  150. Question 150Wheels and Tires

    A tire marked with the speed symbol H is rated for a maximum sustained speed of:

    1. 149 mph
    2. 130 mph Correct answer.
    3. 112 mph
    4. 168 mph

    Explanation

    The speed symbol is the letter at the end of the size designation that gives the top sustained speed the tire can withstand under load. H corresponds to 130 mph. S is 112 mph, V is 149 mph, and W is 168 mph.

  151. Question 151Wheels and Tires

    A vehicle equipped with an indirect tire pressure monitoring system determines low tire pressure by:

    1. monitoring the temperature of the air inside each tire
    2. measuring sidewall deflection with a strain gauge mounted at each hub
    3. comparing wheel speeds reported by the ABS wheel speed sensors Correct answer.
    4. radio signals sent from a battery-powered sensor in each wheel

    Explanation

    An indirect system has no pressure sensors in the wheels. It infers pressure loss from the fact that an underinflated tire has a smaller rolling radius and therefore rotates faster than the others, which the ABS wheel speed sensors detect. This is why the system must be reset after inflation, rotation, or tire replacement.

  152. Question 152Wheels and Tires

    When match-mounting a new tire to a wheel, the tire's high-spot mark should be aligned with the wheel's:

    1. heaviest point, shown by the existing balance weights
    2. inboard bead seat taper
    3. low spot, usually marked by a dimple or located at the valve stem Correct answer.
    4. outboard flange lip

    Explanation

    Match mounting cancels first-order radial force variation by placing the stiffest, largest-radius part of the tire at the smallest-radius part of the wheel. The tire's high spot is marked with a paint dot, and the wheel's low spot is marked with a dimple or is assumed to be at the valve stem hole. This reduces the amount of balance weight and the road force the assembly produces.

  153. Question 153Wheels and Tires

    A cast aluminum wheel has no outboard flange lip to accept a clip-on weight. The technician should balance it using:

    1. one static weight placed at the wheel center
    2. uncoated lead clip-on weights on both flanges
    3. coated clip-on weights on the inboard flange only
    4. adhesive weights attached to the inner and outer barrel surfaces Correct answer.

    Explanation

    Alloy wheels often lack the flanges needed to grip a clip-on weight and can be cosmetically damaged by hammering one on. Adhesive (tape) weights applied to the flat inner and outer barrel surfaces allow a two-plane balance to be performed without harming the finish. Balancing on one plane only leaves a dynamic imbalance that can produce a shimmy.

  154. Question 154Wheels and Tires

    A customer asks a shop to install two new radial tires on the front of a vehicle whose rear tires are bias-ply. The technician should:

    1. decline the job, since radial and bias-ply tires should not be mixed Correct answer.
    2. install the radials after matching the overall tire diameters
    3. install the radials on the front axle and inflate them 4 psi above placard
    4. install the radials and move the bias-ply tires to the front axle

    Explanation

    Radial and bias-ply tires have very different cornering stiffness and slip characteristics, so mixing them on one vehicle produces unpredictable handling, especially in an emergency maneuver. The industry rule is that all four tires should be of the same construction type. Matching diameters does not correct the difference in handling behavior.

  155. Question 155Wheels and Tires

    After installing wheels and tightening the lug nuts with a calibrated torque wrench, the technician should recheck torque:

    1. at the next 3,000-mile service interval
    2. immediately after the vehicle is lowered from the lift
    3. only if a vibration appears at highway speed
    4. after the vehicle has been driven about 25 miles Correct answer.

    Explanation

    Fasteners settle as the wheel seats against the hub during the first few miles of driving, so the clamp load can drop even when the original torque was correct. Checking again after roughly 25 miles (or per the manufacturer's interval) restores the specified clamp load before the wheel can loosen. Waiting for a vibration means the joint has already begun to fail.

  156. Question 156Wheels and Tires

    A front-wheel-drive vehicle has four matching non-directional tires of the same size. The recommended rotation pattern is:

    1. front tires straight to the rear; rear tires crossed to the front
    2. front tires crossed to the rear; rear tires straight ahead Correct answer.
    3. all four tires moved one position clockwise
    4. front and rear tires swapped side to side only

    Explanation

    On a front-wheel-drive vehicle the forward-cross pattern is used: the rear tires move straight forward to the front axle, and the front tires cross to the opposite side of the rear axle. Driven front tires wear faster and benefit from moving to the less loaded rear positions. Straight-back patterns are used on rear-wheel-drive vehicles.

  157. Question 157Wheels and Tires

    A tire loses about 3 psi per week, and soap bubbles appear along the inboard bead on a steel wheel. The most likely cause is:

    1. a nail in the tread that has temporarily sealed itself
    2. a leaking valve core that is allowing air past the valve stem
    3. porosity in the tire sidewall allowing slow air loss
    4. corrosion on the rim flange preventing the bead from sealing Correct answer.

    Explanation

    Air escaping through the bead seat is confirmed by the bubbles at that exact location. On steel wheels, rust and corrosion build up on the flange and lift the bead away from the rim, creating a slow leak. The repair is to demount the tire, clean and seal the flange, and remount.

  158. Question 158Wheels and Tires

    A vehicle develops a hum that begins around 40 mph. The noise is unchanged on a freshly paved section of road but changes noticeably when the vehicle is swerved left and right. The most likely cause is:

    1. a worn wheel bearing Correct answer.
    2. a tire with a chopped tread pattern
    3. an out-of-balance wheel assembly
    4. a defective tire pressure sensor

    Explanation

    Swerving transfers load from side to side, which changes the load on a wheel bearing and therefore changes its noise; tire noise does not respond that way. Tire noise instead changes with road surface, and here it did not change on new pavement. Imbalance produces a vibration felt through the steering wheel or seat rather than a steady hum.

  159. Question 159Wheels and Tires

    After a two-plane balance and a runout check that are both within specification, an assembly still produces a 30-pound road force reading on the balancer. The best next step is to:

    1. install a centering ring and recheck runout
    2. match-mount the tire to a different position or replace it Correct answer.
    3. rebalance the assembly with adhesive weights
    4. raise inflation pressure by 10 psi and recheck

    Explanation

    Road force measures stiffness and radius variation around the tire, which balancing and runout checks do not correct. A reading in the 30-pound range indicates a uniformity problem that will produce a vibration even though the assembly is smooth and round enough. Indexing the tire on the wheel, or replacing the tire if indexing does not reduce the reading, is the appropriate action.

  160. Question 160Wheels and Tires

    A technician coats the wheel studs with anti-seize compound before tightening the lug nuts to the published dry torque specification. The result will most likely be:

    1. correct clamp load, because torque is measured with a calibrated wrench
    2. no effect, because anti-seize evaporates after installation
    3. excessive clamp load and possible stud stretch or breakage Correct answer.
    4. loose lug nuts, because the lubricant reduces friction

    Explanation

    Torque specifications assume a specific coefficient of friction between the threads, nut seat, and wheel. Lubricating the threads lets the nut turn farther for the same applied torque, so more of that torque becomes clamp load. The result is over-tensioned studs that can stretch or break, which is why fasteners must be torqued dry unless the specification states otherwise.

  161. Question 161Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    The top of a vehicle's left front tire leans outward, away from the vehicle centerline. Which alignment angle does this describe?

    1. Negative toe
    2. Positive camber Correct answer.
    3. Positive caster
    4. Negative camber

    Explanation

    Camber is the inward or outward tilt of the top of the wheel as viewed from the front of the vehicle. Outward tilt at the top is positive camber; inward tilt is negative camber. Caster and toe are measured in different planes and do not describe this lean.

  162. Question 162Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    What is the primary effect of positive caster on steering?

    1. It improves straight-line stability and steering wheel return Correct answer.
    2. It reduces rolling resistance at highway speed
    3. It reduces steering effort at parking speeds
    4. It increases the size of the tire contact patch

    Explanation

    Positive caster tilts the steering axis so the tire contact patch trails the point where the axis meets the ground, creating self-aligning torque that helps the wheels return to center and adds high-speed stability. It increases, rather than decreases, low-speed steering effort.

  163. Question 163Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Toe-in means that, when viewed from above, the fronts of the tires are:

    1. Farther apart than the rear of the tires
    2. Closer together than the rear of the tires Correct answer.
    3. Tilted rearward at the top
    4. Leaning inward at the top

    Explanation

    Toe is measured in the horizontal plane by comparing the distance across the fronts of the tires to the distance across their rears. Toe-in means the fronts point toward each other, so the front measurement is smaller.

  164. Question 164Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Which component transfers steering force from the tie rod to the steering knuckle?

    1. Idler arm
    2. Pitman arm
    3. Outer tie rod end Correct answer.
    4. Stabilizer link

    Explanation

    The outer tie rod end is the ball-and-socket joint threaded onto the tie rod that attaches to the steering knuckle arm. It transmits steering force while allowing the knuckle to pivot as the suspension moves.

  165. Question 165Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A stabilizer (sway) bar link connects the end of the stabilizer bar to the:

    1. Upper ball joint and wheel hub
    2. Frame and the pitman arm
    3. Lower control arm or strut assembly Correct answer.
    4. Steering knuckle and tie rod

    Explanation

    The bar itself is mounted to the frame or subframe, and the links tie its ends to the lower control arms or struts. Body roll twists the bar through the links, and the bar's resistance reduces roll.

  166. Question 166Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A customer reports a whine from the engine compartment that gets louder whenever the steering wheel is turned. Which is the most likely cause?

    1. Low power steering fluid level Correct answer.
    2. Warped front brake rotor
    3. Worn front wheel bearing
    4. Worn outer tie rod end

    Explanation

    A whine that follows steering input comes from the power steering pump, most often because the fluid level is low or air is being drawn into the system. Noise from a wheel bearing or a rotor does not respond directly to turning the steering wheel.

  167. Question 167Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A front tire is worn heavily on both outer shoulders while the center tread remains deep. Which condition is most likely?

    1. Excessive positive caster
    2. Overinflation
    3. Underinflation Correct answer.
    4. Excessive toe-out on one side

    Explanation

    Underinflation lets the tire bulge so the shoulders carry more of the load than the center, producing wear on both outer edges. Overinflation produces the opposite pattern, with the center wearing faster than the edges.

  168. Question 168Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Changing the length of the tie rods on a rack-and-pinion vehicle adjusts which alignment angle?

    1. Steering axis inclination
    2. Toe Correct answer.
    3. Caster
    4. Camber

    Explanation

    Tie rods set the fore-and-aft position of the front of each wheel, so changing their length changes toe. Camber, caster and steering axis inclination are established by the strut, knuckle and control arm geometry.

  169. Question 169Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle wanders at highway speed, needs constant corrections, and the steering wheel returns to center slowly after a turn. Which alignment condition best matches these symptoms?

    1. Insufficient positive caster Correct answer.
    2. Excessive toe-in
    3. Excessive positive caster
    4. Excessive negative camber

    Explanation

    Positive caster provides the self-aligning torque that stabilizes the steering and returns the wheel to center. Too little caster leaves the steering vague and wandering, especially at highway speed.

  170. Question 170Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Measured steering axis inclination (SAI) is 11 degrees on the left front and 15 degrees on the right front, and both camber readings are within specification. What is the most likely cause?

    1. An incorrect rear toe setting
    2. A worn outer tie rod end on the left side
    3. A bent steering knuckle or strut on the right side Correct answer.
    4. A loose steering column coupling

    Explanation

    SAI is built into the knuckle and spindle geometry and is not adjustable. A side-to-side difference of more than about one degree indicates a bent knuckle, strut or control arm on the side with the abnormal reading.

  171. Question 171Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    The rear axle of a vehicle is set so its thrust line is not parallel with the vehicle centerline. Which symptom will the driver most likely notice?

    1. The steering wheel off-center while the vehicle drives straight Correct answer.
    2. A pull that occurs only during braking
    3. A vibration through the steering wheel at highway speed
    4. A clunk when the steering wheel is turned

    Explanation

    Thrust angle is the direction the rear axle points relative to the centerline. When it is offset, the front wheels must be turned to keep the vehicle traveling straight, which leaves the steering wheel off-center, a condition often called dog tracking.

  172. Question 172Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    After a turn, a vehicle keeps pulling in the direction of that turn until the driver corrects it. Which is the most likely cause?

    1. Incorrect total toe setting
    2. Binding strut bearing or upper mount Correct answer.
    3. Worn idler arm bushing
    4. Worn outer tie rod end

    Explanation

    Memory steer occurs when a component at the top of the strut binds and prevents the strut from returning freely, so the steering stays where it was last placed. Freeing the bearing or mount restores normal return.

  173. Question 173Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle's toe changes as the front suspension moves through bump and rebound. What is this condition called?

    1. Memory steer
    2. Torque steer
    3. Ackermann error
    4. Bump steer Correct answer.

    Explanation

    Bump steer is toe change caused by suspension travel, usually because the inner tie rod pivots are at the wrong height relative to the control arm geometry. Drivers often describe it as the vehicle darting when it crosses dips or bumps.

  174. Question 174Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle steady-pulls to the right at highway speed. Which is the best first step to determine whether a tire is causing the pull?

    1. Swap the two front tires left to right and road test Correct answer.
    2. Replace both front tires
    3. Add caster to the left side
    4. Set toe to specification and road test

    Explanation

    Radial tire conicity can create a steady pull, and crossing the front tires moves each one to the opposite side. If the pull reverses direction after the swap, the tire is the cause.

  175. Question 175Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle has a growling noise that gets louder in right turns and quieter in left turns. How should the technician use this information?

    1. Check and adjust tire pressure
    2. Suspect the bearing on the loaded side, since noise rises with load Correct answer.
    3. Measure wheel runout with a dial indicator
    4. Perform a static wheel balance check

    Explanation

    Cornering shifts weight onto the outside wheels, so a bearing that is noisy in a right turn is the one on the left side that is being loaded. Identifying the loaded side narrows the diagnosis before any parts are removed.

  176. Question 176Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A tire has a scalloped, cupped wear pattern around its circumference. Which is the most likely cause?

    1. Excessive positive camber
    2. Overinflation
    3. Worn shock absorbers or struts Correct answer.
    4. Incorrect toe setting

    Explanation

    Cupping results when the tire bounces and skips as it rolls, which happens when the dampers can no longer control wheel motion. Severe wheel imbalance can produce a similar pattern, but worn dampers are the classic cause.

  177. Question 177Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle with electric power steering has reduced assist and the warning light is on. What is the most appropriate first step?

    1. Adjust front toe to specification
    2. Replace the steering gear assembly
    3. Retrieve diagnostic trouble codes from the power steering control module Correct answer.
    4. Replace the steering angle sensor

    Explanation

    Electric power steering assist is controlled by a module that monitors the torque sensor, motor and vehicle speed inputs. Reading codes and datastream values first identifies which circuit or component has actually failed.

  178. Question 178Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A front-wheel-drive car pulls to the right only under hard acceleration and goes straight when the throttle is released. What is the most likely cause?

    1. Worn steering damper
    2. Torque steer from unequal-length halfshafts Correct answer.
    3. Incorrect toe setting
    4. Excessive positive caster on the left side

    Explanation

    On front-wheel drive, unequal halfshaft lengths and angles produce different torque reactions at each front wheel, so the car pulls only while torque is applied. Alignment or damper problems create pulls that are present during steady cruise.

  179. Question 179Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Toe-out on turns (Ackermann) is designed so that:

    1. Toe returns to zero as the steering wheel is turned
    2. Both front wheels stay parallel throughout a turn
    3. The rear wheels steer opposite the front wheels
    4. The inner wheel turns a tighter angle than the outer wheel Correct answer.

    Explanation

    The inner wheel follows a smaller radius in a turn, so the steering arms are angled to make it turn more sharply than the outer wheel. This reduces tire scrub and is checked with a toe-out on turns reading.

  180. Question 180Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Before adjusting any alignment angle, a technician should verify:

    1. Ride height, tire pressure and tire size Correct answer.
    2. Engine oil level and battery charge
    3. Wiper blade condition
    4. Radio and HVAC settings

    Explanation

    Alignment specifications assume the vehicle sits at design height with the correct tires at the specified pressures. Sagging springs, low tires or the wrong size tires change camber, caster and toe readings and make the adjustment inaccurate.

  181. Question 181Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    Which statement correctly describes the relationship among steering axis inclination (SAI), camber and included angle?

    1. Included angle equals camber minus SAI
    2. Included angle equals SAI plus camber Correct answer.
    3. Camber equals included angle plus SAI
    4. SAI equals included angle plus camber

    Explanation

    Included angle is the angle between the steering axis and the wheel plane, so it is found by adding SAI and camber. Comparing included angle and SAI with their specifications helps identify a bent knuckle or strut.

  182. Question 182Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A recirculating-ball steering gear has excessive steering wheel free play that remains after the worm bearing preload is set. What is the next adjustment to consider?

    1. Sector shaft over-center preload Correct answer.
    2. Caster adjustment
    3. Tie rod sleeve adjustment
    4. Steering column tilt pivot

    Explanation

    Recirculating-ball gears have two adjustments: worm bearing preload removes end play, and sector shaft over-center preload removes lash at the center of travel. The over-center adjustment must be made at the center position to avoid binding and poor return.

  183. Question 183Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle has incorrect caster and the strut has no factory caster adjustment. What is an acceptable method to correct the caster?

    1. Reducing tire pressure on one side
    2. Adjusting the toe setting
    3. Installing a camber/caster plate or an offset upper strut mount Correct answer.
    4. Changing the tie rod length

    Explanation

    When the strut mounting offers no slots or eccentrics for caster, an aftermarket camber/caster plate or offset upper mount shifts the top of the strut to change the steering axis angle. Any slotting of the tower must follow service information.

  184. Question 184Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    After a four-wheel alignment the vehicle drives straight, but the steering wheel sits off-center. What is the most appropriate correction?

    1. Adjust rear toe to move the thrust angle
    2. Replace the steering gear
    3. Center the wheel with the tie rods while maintaining total toe Correct answer.
    4. Adjust caster until the wheel is centered

    Explanation

    With total toe correct, steering wheel position is set by turning the two tie rods equal amounts in opposite directions. This centers the wheel without changing total toe, so the alignment values already established stay intact.

  185. Question 185Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    After a wheel alignment or a steering gear replacement on a vehicle equipped with electronic stability control, what is typically required?

    1. Bleed the brake master cylinder
    2. Calibrate the steering angle sensor Correct answer.
    3. Relearn the TPMS sensor IDs
    4. Reset the transmission adaptive memory

    Explanation

    The stability control module uses the steering angle sensor to determine the driver's intended direction. If the sensor-to-steering-wheel relationship has changed, a zero-point calibration is required or the system may set codes and illuminate the warning light.

  186. Question 186Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A power steering system was serviced, and afterward the fluid is foamy and the pump is noisy. Which action is most likely to correct the condition?

    1. Add stop-leak to the reservoir and recheck the level
    2. Increase the tension of the pump drive belt
    3. Top off the reservoir until the foam overflows
    4. Bleed air by turning the wheel lock to lock Correct answer.

    Explanation

    Air trapped in the system is churned into foam by the pump, which produces noise and an aerated fluid level. The specified bleed procedure, turning the steering from lock to lock with the engine running and pausing at each stop, pushes the air out through the reservoir. Sealer additives and overfilling do not remove air and can make aeration worse.

  187. Question 187Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A technician grasps a front tire at the top and bottom and feels looseness, but the movement disappears when a helper holds the brake pedal down firmly. Which component is worn?

    1. Wheel bearing Correct answer.
    2. Outer tie rod end
    3. Strut rod bushing
    4. Lower ball joint

    Explanation

    Applying the brakes clamps the rotor between the pads, so any play coming from the wheel bearing is taken up and can no longer be felt at the tire. Tie rod play is normally detected by rocking the tire at the 3 and 9 o'clock positions and is not masked by the brakes. Ball joint play would still be present with the brakes applied because the knuckle can still move relative to the control arm.

  188. Question 188Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A front stabilizer bar link is broken on one side. Which symptom would the customer most likely report?

    1. Cupped wear on the inside edge of the front tires
    2. The steering wheel sitting off-center while driving straight
    3. A steady pull to one side at highway speed
    4. A rattle or clunk over bumps and in turns Correct answer.

    Explanation

    The link connects the stabilizer bar to the control arm or strut, and when it is broken the bar is free to swing and strike the surrounding parts. That produces a rattle or clunk over uneven pavement and during turns, when the bar is loaded. A broken link does not change alignment angles, so it does not cause a pull, tire wear, or an off-center steering wheel.

  189. Question 189Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    On a torsion bar front suspension, ride height is changed by:

    1. Rotating the tie rod adjusting sleeves
    2. Installing a shorter strut assembly
    3. Turning the torsion bar adjuster bolt Correct answer.
    4. Changing the shims behind the upper control arm

    Explanation

    The adjuster bolt changes the twist, or preload, built into the torsion bar, which raises or lowers the lower control arm and therefore the vehicle. Shims at the control arm change camber and caster, and the tie rod sleeves change toe. Ride height must be set correctly before alignment angles are measured because it affects camber and caster.

  190. Question 190Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle pulls to the right only while braking, and the left front tension strut (strut rod) bushing is torn. Which alignment angle is most directly affected by this defect?

    1. Caster Correct answer.
    2. Thrust angle
    3. Toe
    4. Camber

    Explanation

    The tension strut controls the fore-aft position of the lower control arm and its ball joint. When the bushing deflects under braking, the ball joint moves rearward, reducing positive caster on that side and creating a pull toward the side with less caster. Toe, camber, and thrust angle are set by other components and are not primarily controlled by this strut.

  191. Question 191Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A technician finds up-and-down play in the inner tie rod socket where it attaches to the rack, while the outer tie rod end is tight. What is the correct repair?

    1. Replace the outer tie rod end
    2. Install a new rack boot and recheck
    3. Adjust the rack guide to remove the play
    4. Replace the inner tie rod end Correct answer.

    Explanation

    Play located at the inner socket is wear in that joint, so the inner tie rod end, or the rack if the socket is not serviceable separately, must be replaced. The rack guide sets the mesh between the rack and pinion and does not remove play from the inner tie rod joint. A boot only protects the joint from contamination and cannot correct looseness.

  192. Question 192Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    During a power steering pressure test, the gauge reads below specification when the shutoff valve is closed at idle. What does this result indicate?

    1. A leaking rack piston seal
    2. An internally leaking pump Correct answer.
    3. Air trapped in the system
    4. A restricted return hose

    Explanation

    Closing the shutoff valve dead-heads the pump, so the reading shows the maximum pressure the pump itself can produce. A reading below specification means the pump is losing pressure internally, typically through the relief valve, vanes, or internal clearances. A restriction or air affects flow and noise, and a rack seal leak affects assist and fluid loss, but neither limits the pump's dead-head pressure in this way.

  193. Question 193Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle has a steering wheel vibration at 60 mph. The tires have been balanced twice and radial runout is within specification, but the vibration remains. Which is the best next step?

    1. Re-balance the wheels using more balance weights
    2. Replace the front struts
    3. Lower the tire pressure to soften the ride
    4. Measure road force and match-mount the tires Correct answer.

    Explanation

    Road force variation, sometimes called stiffness variation or conicity, produces a vibration that balancing cannot correct because the problem is in the tire's force characteristics rather than its mass distribution. Measuring road force and match-mounting the tire to the wheel minimizes the variation. Additional weights or lower pressure do not address the cause, and struts are not a cure for a speed-specific wheel vibration.

  194. Question 194Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    After the steering column was removed and reinstalled, the steering binds only at certain steering wheel angles. Which is the most likely cause?

    1. An incorrect toe setting
    2. A worn rack guide
    3. U-joints out of phase Correct answer.
    4. Excessive caster at the front wheels

    Explanation

    Universal joints in the intermediate shaft must be phased correctly so that the speed variations they create cancel each other. When they are out of phase, the shaft binds and releases as it rotates, producing uneven effort at particular steering wheel angles. Alignment angles and rack guide wear do not cause a bind that repeats once per shaft revolution.

  195. Question 195Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A strut-to-knuckle fastener is specified as torque-to-yield. Which procedure is correct?

    1. Reuse the bolt and torque it to the highest value in the published range
    2. Apply thread locker and torque to 50 percent of the specification
    3. Torque the bolt cold, then retorque it after the vehicle is driven
    4. Replace the bolt and torque it to spec plus the specified angle Correct answer.

    Explanation

    Torque-to-yield bolts are tightened into their elastic limit and stretch permanently, so they are designed for one use only. The correct procedure is to install a new bolt, torque it to the specified value, and then turn it the additional specified angle. Reusing the bolt or under-tightening it can result in loss of clamp load and fastener failure.

  196. Question 196Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A front tire shows a feathered wear pattern, with tread block edges sharp on one side and rounded on the other across the tread face. Which alignment angle is most likely incorrect?

    1. Toe Correct answer.
    2. Camber
    3. Steering axis inclination
    4. Caster

    Explanation

    Feathering is caused by the tire being dragged sideways as it rolls, which scribes the tread blocks so one edge is sharp and the opposite edge is rounded. Incorrect toe is the classic cause of this pattern. Camber produces wear concentrated on one shoulder, and caster and SAI do not produce a feathered tread face.

  197. Question 197Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A rack-and-pinion steering gear has fluid inside the bellows boot, and the boot is intact with its clamps tight. What does this indicate?

    1. Normal assembly lubricant expelled during operation
    2. A failed seal inside the steering gear Correct answer.
    3. A leaking pressure hose routed above the boot
    4. An excessive fluid level in the reservoir

    Explanation

    An intact boot with tight clamps means fluid found inside it had to come from within the gear, past the rack shaft seal. That seal failure allows hydraulic fluid to enter the boot, and the gear must be replaced or resealed. Lubricant in the boot is grease, not hydraulic fluid, and an external hose leak or an overfilled reservoir would wet the outside of the boot or vent at the cap rather than fill the boot.

  198. Question 198Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A front-end alignment shows left camber at +0.4 degree, right camber at -0.4 degree, equal caster on both sides, and toe within specification. Which behavior is expected?

    1. Feathered wear on both front tires
    2. A pull toward the left Correct answer.
    3. A steering wheel shimmy at highway speed
    4. A pull toward the right

    Explanation

    A vehicle tends to drift toward the side with the more positive camber, because that wheel leans outward and rolls on a larger effective radius. With the left side more positive than the right, the result is a pull to the left. Equal caster removes caster as a cause, and toe is in specification, so neither shimmy nor feathered wear is explained by these readings.

  199. Question 199Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A vehicle drifts to the right on a heavily crowned road. Assuming the manufacturer allows a caster range, which setting should the technician choose to reduce the drift?

    1. More negative camber on the left than on the right
    2. Equal negative caster on both sides
    3. More positive caster on the right than on the left
    4. More positive caster on the left than on the right Correct answer.

    Explanation

    Caster creates a directional bias, and the side with more positive caster tends to lead, so adding positive caster to the left counteracts a rightward drift. Negative caster on both sides reduces straight-line stability and is not a recommended correction. Camber changes affect a steady pull differently and are not the adjustment asked for here.

  200. Question 200Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

    A solid-axle front suspension develops a violent shimmy after the vehicle hits a bump at highway speed, and the tie rods and ball joints are tight. Which component should be inspected first?

    1. The steering damper
    2. The track bar bushings Correct answer.
    3. The front wheel bearings
    4. The rear sway bar links

    Explanation

    A shimmy triggered by a bump on a solid front axle usually comes from lost lateral control of the axle, and the track bar is the component that locates the axle side to side. Worn bushings or a loose bracket allow the axle to shift and set off the oscillation. A damper may mask the symptom, and wheel bearings or rear sway bar links do not locate the front axle laterally.

ASE A4 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Recirculating ball steering gear
A steering gear in which a ball nut rides on recirculating ball bearings along a worm shaft, moving a sector shaft that swings the pitman arm.
Ackermann steering geometry
Geometry in which the inner front wheel steers a sharper angle than the outer wheel so both wheels roll on arcs sharing a common center, reducing tire scrub.
Included angle
The sum of steering axis inclination and camber. It is not adjustable, so an out-of-spec value indicates a bent knuckle, spindle, or strut.
Steering wheel free play
The amount the steering wheel can be rotated before the front wheels respond, measured at the rim with the wheels straight ahead. Excess indicates worn linkage or gear.
Power steering relief pressure
The maximum pump pressure produced when the steering is held against a stop, typically 1,000 to 1,500 psi, limited by the pump's pressure relief valve.
Electric power steering torque sensor
A sensor that measures torsional deflection of the steering column shaft from driver input, allowing the control module to command proportional assist motor current.
Idler arm function
On parallelogram steering linkage, it supports the end of the center link opposite the pitman arm. Worn idler bushings allow toe change and cause wander.
MacPherson strut
A suspension unit combining a coil spring and damper that also locates the wheel. Camber is adjusted by moving the strut-to-knuckle joint.
Load-carrying ball joint check
A ball joint that supports vehicle weight is checked for axial (vertical) play with the vehicle's weight resting on it, using a dial indicator or pry bar.
Spring rate definition
The force in pounds required to compress a spring one inch. It increases with larger wire diameter, fewer active coils, or smaller mean coil diameter.
Stabilizer bar link noise
Worn sway bar links or bushings produce clunking or rattling over bumps. Verify play by prying components with the suspension at normal ride height.
Control arm bushing preload
Rubber bushings must be tightened with the suspension at normal ride height. Tightening at full droop twists the rubber and causes early failure.
Air suspension height sensor
A sensor that reports ride height to the control module, which runs the compressor and solenoid valves to maintain the programmed trim height at each corner.
Worn strut symptoms
Excessive rebound, cupped tire tread, nose dive during braking, longer stopping distance, and fluid leakage. Lost gas charge reduces damping control.
Camber angle definition
The inward or outward tilt of the wheel top from vertical. Negative camber tilts the top inward and wears the inner tread edge; positive camber does the opposite.
Caster angle definition
The forward or rearward tilt of the steering axis viewed from the side. Positive caster, top rearward, increases straight-line stability and steering effort.
Toe setting definition
The difference between front and rear measurements across a pair of tires. Toe-in means the fronts are closer together; excess toe causes feathered tread wear.
Thrust angle
The average rear toe direction relative to the vehicle centerline. A nonzero thrust angle causes dog tracking and an off-center steering wheel.
Alignment adjustment order
Set tire pressure and ride height first, then caster and camber, then toe last, because toe readings change whenever camber or caster is adjusted.
SAI and included angle
Steering axis inclination is the front-view tilt of the steering axis. Included angle equals SAI plus camber and changes only when parts are bent.
Memory steer
A condition where the vehicle continues to turn after the steering wheel is released, caused by binding strut bearings, ball joints, or column universal joints.
Tire size P225/60R16
225 mm section width, 60 aspect ratio meaning sidewall height is 60 percent of width, radial construction, and a 16-inch rim diameter.
Positive wheel offset
The wheel mounting face is outboard of the wheel centerline. This reduces track width and affects scrub radius, bearing load, and steering feel.
Tread wear indicator
Raised bars molded into the tread grooves at 2/32 inch (1.6 mm), the legal minimum tread depth in most jurisdictions. They appear when replacement is due.
Static versus dynamic balance
Static balance corrects a one-plane up-and-down imbalance. Dynamic balance uses two planes to correct side-to-side rocking of the wheel assembly.
Tire conicity pull
A tire built with offset belt layers that pushes sideways like a cone, causing a steady pull. Cross-swapping the front tires reverses the pull direction.
DOT date code
The final four digits of the DOT tire serial number. The first two digits are the week of manufacture and the last two are the year.
Lug nut torque sequence
Tighten lug nuts in a star or crisscross pattern in progressive stages to the specified torque so the wheel seats squarely and evenly on the hub.
Speed-related vibration diagnosis
Vibration that varies with road speed points to wheels, tires, runout, or driveline. Vibration that varies with engine RPM in neutral points to engine or converter.
CV joint click diagnosis
Clicking or popping during turns under acceleration indicates a worn outer constant velocity joint, most often after a torn boot has released its grease.
Wheel bearing noise test
A growl that changes volume when the vehicle is swerved left versus right identifies a bearing on the loaded or unloaded side, confirmed with a wheel shake.
ADAS recalibration after alignment
Camera and radar systems referenced to the vehicle thrust line may require static or dynamic recalibration whenever ride height, ride attitude, or alignment angles change.

ASE A4 study guide

Steering Systems

Component Recognition

Steering questions usually begin with identifying the system installed. Recirculating-ball gears (common on older RWD cars and trucks) use a worm, ball nut, and sector shaft with a parallelogram linkage: pitman arm, center link, idler arm, and tie rod ends. Rack-and-pinion systems transfer motion directly through the rack to inner and outer tie rod ends and dominate modern vehicles. Knowing which style is present tells you which wear points and adjustments exist.

Hydraulic vs Electric Assist

Hydraulic power steering uses an engine-driven pump; diagnosis centers on both pressure and flow. A restricted hose or worn pump can cause hard steering at low engine speed, stiffness until warm (morning sickness), or a whine that changes with steering input. Check fluid level and aeration first - a foamy reservoir means air is entering, often through a leaking suction-side O-ring. Electric power steering (EPS) uses a motor, torque sensor, and control module; complaints of poor feel are frequently calibration or software issues, not mechanical wear, and a steering angle sensor relearn may be needed after alignment.

Traps

Watch for confusing normal gear lash with excessive free play, and condemning a gear when the noise comes from a worn intermediate shaft or column bearing. Worm bearing preload and sector shaft mesh preload are separate adjustments - overtightening one masks the other and creates binding.

Rule of Thumb

With wheels straight ahead and the engine running, steering wheel free play measured at the rim should not exceed roughly 1 inch (25 mm); more points to tie rod ends, idler arm, or gear wear. Have an assistant rock the wheel while you watch each joint.

Suspension Systems

Types and Load Paths

Suspension questions test whether you know where the weight goes. On a MacPherson strut, the strut carries the spring load and the lower ball joint is typically load-bearing (axial). On a short-long arm design the spring sits on the lower control arm, so the lower joint is load-bearing and the upper is a follower. Solid axles use leaf or coil springs with control arms and a track bar; independent rear suspensions often use multilink layouts with separate links setting camber and toe.

Wear Items and Diagnosis

Coil springs sag and change ride height, which shifts camber and caster. Torsion bars are adjusted at the anchor and can be re-indexed. Sway bar links and bushings clunk over bumps or while turning; torn control arm bushings cause wander and memory steer. Struts and shocks are diagnosed by oil leakage, tire cupping, floating over dips, and excessive body motion - the old bounce test is unreliable on gas-charged units.

The Big Trap

Checking ball joints with the suspension hanging is the classic error. Follow the manufacturer's procedure: many lower joints must be checked at ride height with the joint unloaded by prying under the tire, while others require a dial gauge. Vertical play on a loaded joint can be invisible.

Worked Example

A vehicle clunks over bumps with uneven front tire wear: check sway bar links with the suspension loaded, then check the strut mount bearing by turning the wheel and feeling for bind. Replace in pairs on the same axle when the opposite side shows similar wear.

Wheel Alignment

The Angles

Camber tilts the tire top in or out; too much negative camber wears the inner shoulder. Caster is the steering axis tilt and provides directional stability and returnability - it does not wear tires but causes a pull toward the side with less positive caster. Toe is the difference in distance between the front and rear of the tires; incorrect toe causes feathered tread wear and is the largest single tire-wear angle. Thrust angle is the direction the rear axle points relative to the vehicle centerline; if it is off, the steering wheel sits crooked going straight and the vehicle dog-tracks. SAI and included angle help identify a bent strut, knuckle, or spindle when camber cannot be brought into spec.

Pre-Alignment Inspection

Never align a worn front end. Check tire pressures and sizes, ride height, ball joints, tie rod ends, wheel bearings, and steering gear free play. Set pressures and center the steering wheel before reading. Many vehicles require a steering angle sensor reset and, on some, a ride height calibration afterward.

Traps

Confusing cross-camber with cross-caster as the cause of a pull; assuming a crooked steering wheel is toe when it may be thrust angle; and aligning a vehicle with a bent component, which yields a perfect printout and a poor-driving car.

Rule of Thumb

Camber wears, caster pulls, toe feathers. If a car drifts right, compare cross-caster - it pulls toward the side with less positive caster.

Wheels and Tires

Reading the Sidewall

A size like P225/60R16 98H decodes as passenger tire, 225 mm section width, 60 aspect ratio, radial construction, 16-inch rim, 98 load index, and H speed rating. Replacement tires must meet or exceed the OE load index and speed rating. The DOT date code uses the last four digits (week and year) to show age; tires around six years old deserve scrutiny regardless of tread depth.

Wheels and Hardware

Offset is the distance from the wheel's mounting face to its centerline; positive offset moves the tire inboard and is common on FWD cars. Backspacing is measured from the inner edge to the mounting face, so the two numbers are not interchangeable. Match bolt pattern and hub bore - hub-centric wheels center on the hub, lug-centric wheels center on tapered nuts torqued in a star pattern.

Tire Service

Tread wear indicators appear at 2/32 inch; 4/32 is the practical wet-traction limit. Balance problems show as vibration at a specific speed; road force measurement catches stiff spots and runout that conventional balancing misses. Check radial and lateral runout on the wheel before condemning a tire. Directional and asymmetric tires must be mounted correctly.

TPMS

Direct systems use wheel sensors and require a relearn after rotation or sensor replacement, via scan tool or activation sequence. Indirect systems use ABS wheel speed sensors and need only a driver-information-center reset.

Trap

Assuming a TPMS light means a failed sensor. Verify pressures first, then sensor battery age, signal, and module codes.

Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

Symptom Sorting

The miscellaneous domain rewards a disciplined road test. Vibration that changes with vehicle speed but not engine speed points to tires, wheels, or bearings; vibration tied to engine RPM in a given gear points to the driveline. Wheel bearing noise typically changes when the bearing is loaded - swerving left loads the right bearing. Tire noise is usually constant and rises in pitch with speed; a cupped tire howls.

Steering Feel Complaints

Memory steer (the vehicle continues in the direction last turned) suggests binding strut mounts, ball joints, or steering column joints. Torque steer on unequal-length halfshaft cars is normal to a degree; excessive torque steer points to worn control arm bushings or a failed motor mount. Bump steer means toe changes as the suspension travels, usually from worn or improperly installed steering linkage or a lowered vehicle needing a bump-steer kit.

Electronics and Calibration

Modern diagnosis includes steering angle sensor calibration after alignment, EPS DTCs for torque sensor plausibility, and adaptive damper faults. Check for TSBs and software updates before replacing a module.

Safety and Process

Interview the customer about when the noise occurs - cold start, turning, braking, over bumps. Reproduce it before repair, verify the fix afterward, and torque fasteners to spec; many suspension fasteners are torque-to-yield and must not be reused.

Rule of Thumb

If the complaint is speed-sensitive, rotate the tires front to rear and retest. If the vibration moves, it is the tire/wheel assembly, not the chassis.

ASE A4 cheat sheet

Quick reference

Steering Systems

  • Steering gear ratio = steering wheel degrees divided by road wheel degrees; a numerically higher ratio means lower steering effort and slower response.

  • Rack-and-pinion: pinion rotation moves the rack laterally; inner tie rod sockets thread into the rack ends, and play is checked by rocking the tire at the 3 and 9 o'clock positions.

  • Recirculating-ball gear uses a worm shaft, recirculating ball nut, sector shaft, and pitman arm; both worm bearing preload and sector shaft mesh preload are adjustable.

  • Hydraulic power steering pump relief pressure is typically about 1,000-1,500 psi; a flow control valve limits flow at high engine speed to preserve road feel.

  • Electric power steering relies on a torque sensor plus steering angle sensor plus assist motor; a detected fault normally defaults the system to manual steering and sets a DTC.

  • Included angle = SAI + camber; it is not adjustable, so a value outside spec indicates a bent knuckle, spindle, or strut.

  • Parallelogram linkage consists of pitman arm, idler arm, center link, and tie rod assemblies; a worn idler arm bushing changes toe dynamically as the linkage loads and unloads.

  • Free play is measured at the steering wheel rim with the wheels straight ahead; excess play is traced in order from the wheel through the column joints, gear, and tie rods.

  • Bleed a hydraulic system lock-to-lock with the front wheels off the ground; whine or growl after bleeding usually indicates aeration or a restricted return line.

Quick reference

Suspension Systems

  • A MacPherson strut is a structural locating member as well as a spring/damper; camber is adjusted at the strut-to-knuckle joint using slotted holes or cam bolts.

  • On a short-long arm (SLA) suspension, camber is set with shims at the upper control arm and caster with shims at the upper arm pivot.

  • Spring rate in lb/in increases with larger wire diameter, fewer active coils, or a smaller mean coil diameter.

  • Ride height must be checked before alignment; sagging springs change camber, caster, and SAI, so alignment set on a sagging vehicle is invalid.

  • Load-carrying ball joints are checked for axial (vertical) play with the vehicle weight on them; follower ball joints are checked for radial play.

  • Rubber bushings and pivot bolts must be tightened with the suspension at normal ride height, otherwise the bushing is torsionally preloaded and fails early.

  • Stabilizer bar links and bushings cause clunk or rattle over bumps; check for play with the suspension loaded and a pry bar.

  • Worn dampers show cupped tire tread, excess rebound, fluid leaks, and longer stopping distances; a bounce test alone is not a valid pass/fail test.

  • Air suspension uses height sensors, a compressor, and a valve block; leveling must be recalibrated after component replacement, and leaks are located with a soap solution.

Quick reference

Wheel Alignment

  • Adjustment order: set tire pressure and ride height first, then caster and camber, and always set toe last because toe changes with camber and caster.

  • Positive camber tilts the top of the wheel outward, negative tilts it inward; excess negative camber wears the inner tread edge, excess positive wears the outer edge.

  • Caster is not a tire-wear angle; increasing positive caster (steering axis top rearward) increases steering effort and improves straight-line stability.

  • Positive toe (toe-in) means the fronts of a tire pair are closer together than the rears; excess toe produces feathered tread wear across the tread face.

  • Thrust angle is the average rear toe relative to the vehicle centerline; a nonzero thrust angle causes dog tracking and an off-center steering wheel.

  • Included angle = SAI + camber; a bent knuckle or spindle changes included angle and cannot be corrected by adjustment.

  • Steering wheel centering is done after toe is set, by adjusting both tie rods equally or repositioning the wheel on the column splines.

  • Setback is one front wheel displaced rearward of the other; it indicates bent suspension or frame components rather than an adjustment error.

  • Toe-out on turns (turning angle) is built into the steering arms and cannot be adjusted; a bent steering arm alters it and also skews included angle.

Quick reference

Wheels and Tires

  • In P225/60R16: 225 mm is section width, 60 is the aspect ratio (sidewall height is 60% of width), R is radial construction, and 16 is rim diameter in inches.

  • Load index gives maximum load capacity and the speed rating letter gives maximum sustained speed; both must meet or exceed the vehicle tire placard.

  • Minimum legal tread depth is 2/32 inch (1.6 mm); the tread wear indicators molded into the grooves are set at that same 2/32 inch height.

  • Positive offset means the mounting face is outboard of the wheel centerline; backspacing is measured from the mounting face to the inner bead flange.

  • Lug nuts are tightened in a star or crisscross pattern in stages to the specified torque so the wheel seats evenly against the hub.

  • Static balance corrects imbalance in one plane (up-down hop); dynamic two-plane balance corrects side-to-side rocking; road-force balancing addresses radial force variation.

  • Direct TPMS sensors contain batteries that typically last 7-10 years; sensor IDs must be registered or relearned after replacement or tire rotation per the service procedure.

  • Directional tires may only be rotated front-to-back on the same side; asymmetrical tires must keep the sidewall marked 'outside' facing outboard.

  • Tire conicity produces a steady pull; it is identified by cross-switching the front tires and seeing whether the pull direction reverses.

Quick reference

Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

  • Vibration that varies with road speed points to wheels, tires, runout, or the driveline; vibration that varies with engine RPM in neutral points to the engine or torque converter.

  • Shimmy occurring mainly at 50-65 mph most often involves wheel balance, radial or lateral runout, or worn steering and suspension joints.

  • Clicking or popping from a front corner during turns under acceleration indicates a worn outer CV joint, usually following a torn boot and grease loss.

  • A wheel bearing growl changes volume when the vehicle is swerved left versus right, because the loaded side changes; confirm with a 12 and 6 o'clock wheel shake.

  • Torque steer on acceleration in a front-wheel-drive vehicle is affected by unequal halfshaft lengths and angles, and is worsened by worn control arm bushings or engine mounts.

  • Memory steer, where the vehicle keeps turning after the wheel is released, is caused by binding strut bearings, ball joints, or steering shaft universal joints.

  • After alignment or ride height changes, steering angle sensor calibration and ADAS camera or radar recalibration may be required by the service procedure.

  • Subframe or cradle shift changes camber and caster on both sides; check body-to-subframe alignment holes before condemning suspension parts.

  • Pull diagnosis order: verify tire pressures, cross-swap tires to test conicity, check for brake drag, then measure alignment angles.

ASE A4 key terms

Rack-and-pinion steering

A steering system in which a pinion gear on the steering shaft turns a toothed rack, and the rack's side-to-side movement pushes the tie rods to pivot the front wheels.

Related: Inner tie rod, Outer tie rod end, Rotary control valve
Recirculating-ball steering

A steering gear that uses a worm shaft and a ball nut with recirculating steel balls to convert steering wheel rotation into movement of a Pitman arm, common on older trucks and large vehicles.

Related: Pitman arm, Steering gear lash
Rotary control valve

A hydraulic valve inside a power steering gear or rack that senses twist between the input shaft and the gear and directs pressurized fluid to the correct side to assist steering effort.

Related: Rack-and-pinion steering, Electric power steering (EPS)
Electric power steering (EPS)

A power steering system that uses an electric motor, controlled by a module reading steering torque and vehicle speed sensors, to provide assist instead of an engine-driven hydraulic pump.

Related: Steering angle sensor, Rotary control valve
Inner tie rod

The rod that threads into the end of the steering rack and connects to the outer tie rod; its threaded adjustment sets front toe on many vehicles.

Related: Outer tie rod end, Toe, Rack-and-pinion steering
Outer tie rod end

The ball-and-socket joint at the outer end of a tie rod that attaches to the steering knuckle, allowing the wheel to pivot while transmitting steering motion.

Related: Inner tie rod, Ball joint
Pitman arm

A lever splined to the steering gear output shaft that converts the gear's rotary output into the side-to-side motion that drives the steering linkage.

Related: Recirculating-ball steering, Steering gear lash
Steering gear lash

The small amount of clearance between the meshing parts of the steering gear; too much produces steering wheel free play, while too little causes binding and poor return.

Related: Recirculating-ball steering, Pitman arm
MacPherson strut

A suspension design in which a single unit combines the shock absorber, coil spring and upper mount, and also serves as the upper locating member for the wheel.

Related: Strut mount bearing, Coil spring, Shock absorber
Short-long arm (SLA) suspension

A suspension layout using upper and lower control arms of unequal length so wheel camber changes are controlled as the suspension moves through jounce and rebound.

Related: Ball joint, Control arm bushing, Camber
Coil spring

A helical steel spring that supports vehicle weight, compresses and extends as the suspension travels over bumps, and also establishes ride height.

Related: Shock absorber, MacPherson strut
Leaf spring

A stack of curved steel leaves that supports the axle and locates it front to back; common on rear suspensions of trucks and older vehicles.

Related: Shock absorber, Stabilizer bar
Shock absorber

A hydraulic damper that converts suspension movement into heat to control spring oscillation, keeping the tire pressed against the road after a bump.

Related: Coil spring, MacPherson strut
Strut mount bearing

The bearing in the top mount of a MacPherson strut that lets the strut and spring rotate with the steering knuckle when the wheels are turned.

Related: MacPherson strut, Memory steer
Stabilizer bar

A torsion spring connected to both sides of the suspension through links; when the body rolls, the bar twists and resists that roll to improve handling.

Related: Control arm bushing, Leaf spring
Ball joint

A pivoting socket joint that connects a control arm to the steering knuckle, allowing suspension and steering movement through their range without binding.

Related: Short-long arm (SLA) suspension, Outer tie rod end
Control arm bushing

An elastomeric or spherical pivot at the control arm's frame attachment that allows suspension movement while isolating road noise and vibration from the body.

Related: Short-long arm (SLA) suspension, Stabilizer bar
Camber

The angle of the wheel measured from vertical when viewed from the front; negative camber tips the top of the tire inward, positive camber tips it outward.

Related: Caster, Included angle, Steering axis inclination (SAI)
Caster

The forward or rearward tilt of the steering axis viewed from the side; positive caster leans the axis rearward and improves straight-line stability and steering return.

Related: Camber, Steering axis inclination (SAI)
Toe

The difference in distance between the front and rear of the two tires when viewed from above; toe-in points the fronts toward each other, toe-out points them apart.

Related: Thrust angle, Toe-out on turns, Inner tie rod
Thrust angle

The direction the rear axle points relative to the vehicle centerline, calculated from rear toe; when it is not zero the steering wheel will be off center.

Related: Toe, Pre-alignment inspection
Steering axis inclination (SAI)

The inward tilt of the steering axis from vertical as seen from the front; it is built into the knuckle and strut and is not adjustable.

Related: Included angle, Camber, Scrub radius
Included angle

The sum of camber and steering axis inclination for a wheel; comparing it side to side helps identify a bent knuckle, strut or spindle.

Related: Steering axis inclination (SAI), Camber
Scrub radius

The distance at the road surface between the steering axis centerline and the center of the tire contact patch; it affects steering feel and road kickback.

Related: Steering axis inclination (SAI), Wheel offset
Toe-out on turns

The change in toe angle of the front wheels as the steering wheel is turned, caused by the steering arms' angle and needed for the inner wheel to follow a tighter arc.

Related: Toe, Pre-alignment inspection
Pre-alignment inspection

The checks performed before measuring alignment, including tire pressures, ride height, tire condition, and play in ball joints, tie rods and wheel bearings.

Related: Thrust angle, Toe-out on turns, Tire placard
Tire aspect ratio

The tire's sidewall height expressed as a percentage of its section width; a 60-series tire's sidewall is 60 percent as tall as the tire is wide.

Related: Load index, Speed rating
Load index

A number molded on the tire sidewall that corresponds to the maximum load the tire can carry at its rated inflation pressure.

Related: Speed rating, Tire placard
Speed rating

A letter molded on the tire sidewall indicating the maximum sustained speed the tire is designed to withstand when properly inflated and loaded.

Related: Load index, Tire placard
Wheel offset

The distance between the wheel's mounting face and its centerline; positive offset moves the mounting face outward, negative offset moves it inward.

Related: Bolt circle, Scrub radius
Bolt circle

The diameter of the circle passing through the centers of the wheel's lug holes, usually written with the stud count, such as 5 x 114.3.

Related: Wheel offset
Road force variation

A balance measurement that also detects stiffness differences around the tire by pressing a loaded roller against it, revealing vibration causes that ordinary balancing misses.

Related: Shimmy, Tire aspect ratio
Tire pressure monitoring system (TPMS)

A system that monitors tire pressure with wheel-mounted sensors and illuminates a warning light when pressure falls below a specified threshold.

Related: Tire placard, Load index
Tire placard

The label on the driver's door jamb listing the manufacturer's recommended cold tire pressures, tire size and load limits for the original equipment.

Related: Tire pressure monitoring system (TPMS), Load index
Memory steer

A condition where the vehicle continues to pull in the direction the steering wheel was last turned after the driver releases it, usually from binding strut bearings or steering linkage.

Related: Strut mount bearing, Torque steer
Torque steer

A pull to one side during acceleration in front-wheel-drive vehicles caused by unequal driveshaft angles or lengths, which changes the steering effect of engine torque.

Related: Memory steer, Bump steer
Bump steer

A change in toe angle as the suspension moves up and down, caused by incorrect tie rod height or geometry, making the vehicle dart when it hits bumps.

Related: Toe, Torque steer
Shimmy

A rapid side-to-side oscillation of the front wheels and steering wheel, typically triggered by tire or wheel imbalance, runout, or worn steering and suspension parts.

Related: Road force variation, Steering angle sensor
Steering angle sensor

A sensor on the steering column that reports steering wheel position to the stability control and electric power steering systems; it usually needs recalibration after alignment or column repair.

Related: Electric power steering (EPS), Shimmy

ASE A4 study plan

8 weeks · About 7 hours per week

Week 1

Steering Systems

  • Identify the major components of a rack-and-pinion and recirculating-ball steering system and state the function of each

  • Explain how power steering pressure and flow are generated, regulated, and relieved in a hydraulic system

  • Diagnose three common steering complaints (hard steering, wander, fluid leak) by listing the tests you would perform in order

  • Describe the correct procedure for inspecting and servicing a steering gear, tie rod ends, and bellows boots

Your checkpoint

A one-page steering system map: components, fluid flow path, and a 3-column table matching each of the three complaints to its tests

Week 2

Steering Systems & Suspension Systems

  • Differentiate parallelogram, rack-and-pinion, and electric power steering assist failure symptoms

  • Identify front and rear suspension types (MacPherson strut, double wishbone, multilink, solid axle) and label their load-bearing parts

  • Test shock absorbers and struts for wear and state the pass/fail criteria you would apply

  • Inspect springs, bushings, ball joints, and sway bar links and rank findings by safety urgency

Your checkpoint

A written 10-item suspension and steering inspection checklist with pass/fail criteria and urgency ranking for each item

Week 3

Suspension Systems

  • Explain how spring rate, ride height, and jounce/rebound travel interact and predict the effect of a collapsed spring

  • Diagnose ball joint and control arm bushing wear using load/unload and dry-park tests

  • Describe the safety procedures for compressing and replacing coil springs and struts

  • Distinguish ride-quality complaints from handling complaints and list the components most likely responsible for each

Your checkpoint

A diagnostic decision flow for five suspension symptoms (clunk, bottoming out, uneven tire wear, pull, body roll) with the top two suspect components each

Week 4

Wheel Alignment

  • Define camber, caster, toe, steering axis inclination, and thrust angle and state the handling effect of each

  • Convert between degrees/minutes and decimal degrees and interpret a printed alignment specification sheet

  • Explain the correct sequence of alignment adjustments and why thrust angle is set before front toe

  • Identify the causes of a vehicle that pulls, a crooked steering wheel, and off-center toe readings

Your checkpoint

A completed alignment worksheet: 6 unit conversions, plus a before/after spec table for a simulated vehicle with your recommended adjustment order written out

Week 5

Wheel Alignment & Wheels and Tires

  • Perform a pre-alignment inspection sequence and list the conditions that must be corrected before measuring

  • Describe how ride height, tire pressure, and steering wheel position affect alignment readings

  • Identify irregular tire wear patterns (cupping, feathering, one-shoulder, center wear) and match each to a likely alignment or inflation cause

  • Explain how a bent strut or worn control arm bushing changes camber and caster

Your checkpoint

A tire-wear-to-cause reference chart with at least six wear patterns, the alignment angle or component implicated, and the corrective action

Week 6

Wheels and Tires

  • Read a tire sidewall and decode size, load index, speed rating, DOT date code, and maximum inflation

  • Explain tire construction (radial vs. bias, tread design, sidewall stiffness) and how each affects ride and handling

  • Describe TPMS indirect and direct systems, sensor relearn procedures, and common false-trigger causes

  • Diagnose vibration complaints by separating tire/wheel, hub, and driveline causes and stating the balancing and runout checks used

Your checkpoint

A tire and wheel diagnostic sheet: sidewall decode exercise plus a vibration isolation table listing at least five complaint patterns and the confirming test for each

Week 7

Wheels and Tires & Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

  • Explain wheel offset, backspacing, bolt pattern, and hub-centric vs. lug-centric mounting and their effects on handling and bearing load

  • Describe the procedures for mounting, balancing, and torqueing wheels to specification, including torque-stick and star-pattern use

  • Diagnose wheel bearing noise, runout, and looseness and distinguish each from tire and brake noise

  • Identify subframe, cradle, and steering column components that affect alignment and describe inspection methods for each

Your checkpoint

A wheel service and bearing diagnosis summary: torque procedure checklist plus a three-symptom comparison table separating bearing, tire, and brake noise

Week 8

Steering Systems & Suspension Systems & Wheel Alignment & Wheels and Tires & Miscellaneous (Related Suspension and Steering Diagnosis and Repair)

  • Integrate all five domains into a full-vehicle diagnostic sequence for a pull-and-vibration complaint

  • Re-test the weakest two domains using timed practice questions and record every missed concept

  • Recite the alignment angle definitions, tire sidewall fields, and torque/safety rules without notes

  • Build a personal list of the ten facts you are most likely to forget and rehearse them

Your checkpoint

A timed 40-question self-test scored at 80% or better, plus a written remediation list for every missed item

Milestones

Week 2: Can name the parts and failure symptoms of rack-and-pinion, recirculating-ball, and electric power steering, and can explain strut vs. double-wishbone load paths without notes

Week 4: Can define all five alignment angles, convert degrees/minutes to decimals accurately, and state the correct adjustment order for a four-wheel alignment

Week 6: Can decode a complete tire sidewall and match at least six irregular wear patterns to their causes, and can explain TPMS relearn and balance/runout checks

Week 8: Scores 80% or higher on a timed 40-question mixed-domain practice test and has a written remediation list for every missed item

ASE A4 exam day

Your checklist

Government-issued photo ID

Bring the ID you used when you registered; the name on the ID must match your registration name. Confirm the exact accepted forms of ID and whether a second form is required with your test provider before test day.

Appointment/registration confirmation

Have your confirmation number, appointment time, and test center address available (printed or on your phone before you enter the building). Confirm whether the center requires a printed copy or accepts a digital version.

Verified test center location and route

Look up the exact street address, parking situation, and building/room entrance the day before. Test centers are sometimes inside business parks or shared buildings; confirm the check-in location and phone number with the provider.

Arrival time buffer

Plan to arrive earlier than your appointment to allow for check-in, ID verification, and any security screening. Confirm the exact recommended arrival window and late-arrival policy with the provider, since you can be denied entry if you are late.

Plan for personal items

Leave phones, smartwatches, notes, and study materials in your vehicle or in the storage the center provides. Assume nothing from outside is allowed at the workstation unless the proctor gives it to you.

Know your test format in advance

Confirm the number of questions and the time limit for the A4 test you scheduled, and whether any questions are scored differently (for example, unscored pilot items). The count and clock are shown on screen at the start-use those.

Confirm whether scratch materials are provided

Many centers supply a marker and blank sheets or a dry-erase board, and you may be required to return them. Do not assume you may bring your own paper, pen, or calculator-confirm with the provider and plan to do alignment-angle math on what is provided.

Glasses/contacts, medication, and layered clothing

Bring whatever you need to read a screen comfortably for the full session and to stay comfortable in a cold testing room. Confirm the provider's policy in advance for any medication or medically necessary item you need at the workstation.

Rest, food, and caffeine routine

Treat the test like a workday: normal sleep schedule, a real meal before you go, and your usual caffeine amount. Do not try a new energy drink or skip breakfast on test morning.

A short, high-yield review sheet (used only before you go in)

One page of items you personally tend to miss-alignment angle relationships, tire wear pattern causes, TPMS relearn basics, power steering diagnosis flow. Review it in the car or lobby, never at the workstation.

Backup transportation and contact number

Have a fallback plan (second driver, rideshare app, transit alternative) and the test center phone number so you can call if you are delayed.

Plan the day

72 hours before

Re-confirm the appointment date, time, and address, and re-read the provider's ID, arrival, and reschedule/cancellation rules. Verify the name on your registration matches your ID exactly; fix any mismatch now, not on test day. Check where you park and how long the walk to the room takes.

72 hours before

Switch from broad study to targeted review: pick your two weakest A4 content areas (commonly alignment angles and diagnosis, or steering/suspension noise and symptom diagnosis) and work practice items with explanations. Stop learning brand-new material 48 hours out-consolidation beats coverage.

24 hours before

Pack the ID and confirmation, lay out clothes, put the route and parking plan on paper, and set two alarms. Do a light 45-60 minute review of formulas and specs only (caster/camber/toe direction and effect, SAI and included angle, thrust angle, tire size/load markings). Then stop.

24 hours before

Normal dinner, no alcohol, no late-night cramming, and a full night's sleep. If you are taking more than one ASE test in the same visit, confirm the order of your tests and how check-in works between them.

Morning of

Eat breakfast, hydrate, use the restroom before check-in, and arrive within the provider's recommended window. Leave the phone in the car or locker. At check-in, present your ID, confirm which tests you are taking, and read the on-screen instructions rather than clicking through them.

During the test - first pass

Read each question completely and answer the ones you know immediately. Watch for qualifiers: EXCEPT, NOT, MOST likely, FIRST step. Budget your pace from the question count and clock shown on screen-roughly a minute to a minute and a half per question leaves review time. Mark hard questions and move on.

During the test - second pass

Return to flagged items. Eliminate choices that are physically impossible or that fix a symptom rather than the cause. For alignment and measurement questions, sketch the geometry on scratch material before choosing. Answer every question-leaving one blank can only cost you.

During the test - final minutes

Check that no question is unanswered, then stop second-guessing answers you were confident about. Submit, collect any score report the center gives you, retrieve your belongings, and confirm with the provider how and when official results are delivered.

Rules to check

  • Bring a valid government-issued photo ID with a name matching your registration. If your ID does not match, you may be refused admission and lose your fee-confirm the accepted ID forms and any second-ID requirement with your test provider before test day.

  • The test is closed-book. No phones, smartwatches, notes, printed material, or outside reference of any kind in the testing room. Unauthorized items can void your session, so store everything as the proctor directs.

  • Do not bring a calculator unless the provider has confirmed one is permitted, and do not bring your own scratch paper or writing instrument. Use only what the center issues and return it as instructed.

  • Confirm the reschedule and cancellation deadline and any associated fee with your test provider, and confirm the late-arrival rule-arriving after the cutoff can forfeit your seat and your payment.

  • Ask the proctor about breaks before you start, and confirm how the clock is handled during a break. Do not assume the timer pauses; leave the room only under the procedure the proctor describes.

  • Answer every question. Unanswered items are scored incorrect, and there is no credit for leaving a question blank-if you must guess, eliminate at least one choice first and confirm the provider's scoring policy if you are unsure.

  • Keep test content confidential. Do not photograph, record, or reproduce questions, and do not discuss specific items with other candidates; doing so can invalidate your result and affect your eligibility for future testing.

  • If equipment fails, the screen freezes, or something disrupts your session, raise your hand immediately and get it documented with the proctor before you continue-report the issue before you leave the building.

ASE A4 FAQ

How many ASE A4 practice questions are available?

The practice set has 200 ASE A4 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many ASE A4 flashcards are available?

The flashcard set has 32 ASE A4 cards. Each card shows the term and its definition.

Which topics does the ASE A4 study material cover?

The ASE A4 study material has 5 sections, including Steering Systems, Suspension Systems, and Wheel Alignment.

What format facts does the catalog list for the ASE A4 exam?

The catalog lists these item types: multiple choice for the ASE A4 exam.