NCATT AET Practice Test

NCATT Aircraft Electronics Technician (AET) Certification

NCATT AET overview

  • 199 practice questions
  • 32 flashcards
  • 6 study guide topics
  • 40 key terms

What you'll study

  • Aircraft Fundamentals17%
  • Basic Electricity and Electronics17%
  • Digital Techniques and Aircraft Computers17%
  • Wiring, Connectors, and Terminations17%
  • Test Equipment, Measurement, and Troubleshooting16%
  • Avionics and Aircraft Systems Installation16%

The NCATT Aircraft Electronics Technician (AET) certification is a personnel credential for technicians who install, maintain, inspect, and troubleshoot avionics and aircraft electrical systems. ASTM International lists NCATT within its certification programs, and the AET is the foundational level of that family - the entry point on which further NCATT endorsements are built. Candidates typically arrive from Part 147 avionics programs, military aviation-electronics training, or maintenance shops where they already work around radios, transponders, autopilots, antennas, and the wiring that ties them to the airframe.

The knowledge base is broad rather than deep: aircraft structures and flight-control and electrical-system fundamentals, DC and AC circuit theory, semiconductor devices, digital logic and aircraft data buses, wire selection, routing and repair, connector and termination work, coaxial and antenna installations, and competent use of multimeters, oscilloscopes, and bonding and continuity testers. Just as important is the documentation and troubleshooting discipline that keeps a repair airworthy.

Exam-day specifics - item count, time limit, passing score, fee, retake and recertification rules - could not be verified against a live authoritative source at the time of writing and are flagged for review. In study terms, start with circuit fundamentals and wiring practices, then move to systems and installation topics; most real-world failures trace back to the first two.

Common mistakes

When reducing a series-parallel network, the candidate collapses resistors across parallel branches as if they were in series (or adds branch currents as if they were voltages), then carries the wrong value forward through the rest of the problem and reports a final answer that is internally inconsistent.

Candidates memorize 'add resistors in series' and 'add reciprocals in parallel' as isolated rules but never redraw the circuit to mark nodes and identify which elements actually share the same current path versus the same voltage. Under exam time pressure they pattern-match on how the schematic looks rather than on node connectivity.

What to do instead

Before any arithmetic, redraw the circuit twice: once marking series elements (same current, no junction between them) and once marking parallel elements (same two nodes). Write the reduction step by step with units attached, then sanity-check the result: total resistance of a network must be greater than the largest series element and less than the smallest parallel branch.

The candidate mixes current directions and sign conventions mid-problem, assigns voltage drops with polarities that contradict the assumed current arrow, and then treats the resulting negative number as a calculation error rather than as a physically meaningful result.

Training material sometimes uses electron flow and sometimes conventional current without stating which, so candidates flip conventions halfway through a Kirchhoff loop or a diode/transistor problem. A negative result then triggers guessing and rework instead of interpretation.

What to do instead

Declare the convention at the top of the work: conventional current, positive terminal to negative through the load, current entering a resistor at the positive end. Keep one direction arrow per loop and never flip it mid-solve. Treat a negative answer as evidence that the actual direction opposes the assumed arrow, and state that explicitly in the answer.

The candidate selects a wire or terminal using only the conductor gauge and ignores derating factors, insulation temperature rating, bundle size, altitude/high-altitude current derating, or the fact that a higher AWG number means a smaller conductor.

Gauge tables are memorized as a single 'ampacity' number, so the candidate treats the wire-selection problem as a lookup rather than as a multi-variable decision. The inverse AWG numbering also causes silent reversal errors in a hurry.

What to do instead

Work the selection as an ordered checklist every time: current required, ambient and bundle derating, altitude correction, insulation temperature rating, voltage drop over the run length, then gauge. Confirm the direction of AWG (larger number = smaller cross-section) with a circular-mil value before committing. Terminal selection follows: wire gauge, stud size, insulation style, and the correct crimp die for that terminal family.

The candidate terminates a shielded cable by grounding the shield at both ends, or leaves a shield floating, or dresses a coax or signal bundle running parallel and tightly bundled with a high-current power feeder.

Shields and separation are taught as 'good practice' rather than as a specific electrical function, so candidates cannot predict the consequence (ground loops carrying circulating current, or inductive coupling of noise into a low-level signal) and therefore cannot choose correctly when the question describes a scenario rather than a rule.

What to do instead

Learn the function behind each rule: the shield is grounded at one point to intercept interference without creating a return path for circulating current; separation and crossing at right angles minimize inductive coupling. When a question describes a symptom (noise on a low-level signal, intermittent audio), trace it back to the physical routing and termination decision that caused it.

The candidate measures resistance or continuity with the circuit energized, or with the component still connected in a network where parallel paths shunt the meter, and then declares the component 'good' or 'shorted' based on the displayed value.

Continuity checks feel binary and safe, so candidates skip the isolation step. Parallel return paths through airframe structure and ground straps are invisible on the schematic the candidate is holding, and a powered circuit can also damage the meter or produce a plausible but meaningless reading.

What to do instead

State and follow the isolation rule on every resistance test: power removed, component disconnected at least one end, meter zeroed or leads compensated. For airframe bonding and return-path checks, identify all parallel paths before interpreting the reading, and compare against the specified resistance limit rather than an eyeballed 'beep'.

The candidate troubleshoots by swapping suspected components one at a time, or trusts a meter reading without regard to the instrument's limitations (burden voltage, crest factor, true-RMS versus averaging, autorange settling, or an AC range used on a DC signal).

Component swapping feels productive and mirrors hangar habits, while meter specifications are treated as fine print. The candidate also assumes any meter reading is the circuit's actual value, so an averaging meter on a distorted waveform or a low-impedance range loading a high-impedance node produces a confident wrong diagnosis.

What to do instead

Use a divide-and-conquer approach: verify power and ground at the load first, then split the circuit at its midpoint and test which half holds the fault, halving the search area each step. Before trusting a number, state what the meter is actually measuring and whether its accuracy and input impedance suit that node; use a true-RMS meter for non-sinusoidal or switching signals.

The candidate describes a digital databus with the wrong physical or logical characteristics, for example treating a one-way, single-transmitter bus as bidirectional, confusing a bus controller/remote terminal architecture with a peer-to-peer one, or mixing bit and byte counts when computing message length or data rate.

Bus specifications are absorbed as a list of names and numbers with no mental model of the wire, the direction of data flow, or the addressing scheme, so closely related buses blur together during recall. Unit confusion compounds the error when calculating throughput.

What to do instead

Build a one-page comparison table per bus covering: number of wires, direction of data flow, how many transmitters can share the bus, word/label structure, data rate, and error detection. Anchor bit-versus-byte by always converting to bits before computing rate (bits per second = words per second x bits per word).

The candidate converts between binary, decimal, and hexadecimal by dropping or misplacing the least significant bits, or misreads a two's-complement negative value as a large positive number, and then answers the follow-on question with that value.

Conversion is done mentally without place-value columns, and the candidate has no habit of validating the result; two's-complement notation in particular looks like an ordinary magnitude value if the sign bit is not deliberately considered.

What to do instead

Write the place-value columns (128, 64, 32, 16, 8, 4, 2, 1, or powers of 16) for every conversion, group binary into nibbles from the right when converting to hex, and state the word width explicitly before applying two's complement. Verify by converting back to the original base.

The candidate explains a stall as a function of airspeed alone (a fixed 'stall speed'), or conflates angle of attack with pitch attitude, and does not account for load factor, weight, or configuration when judging performance and structural limits.

Everyday flying language ties stall to speed, so the underlying aerodynamic cause (exceeding the critical angle of attack) gets replaced by a memorized number. Pitch attitude and angle of attack look similar from the cockpit, and load-factor effects are abstract until worked numerically.

What to do instead

Re-anchor on the cause: a stall occurs when the wing exceeds its critical angle of attack, at any airspeed, attitude, weight, or bank angle. Work load-factor problems as ratios (load factor equals lift divided by weight) and note that stall speed rises with the square root of load factor, so a level 60-degree bank raises stall speed by roughly 40 percent.

When installing avionics line-replaceable units, the candidate routes or secures hardware from habit, bending a coax beyond its minimum radius, using unapproved fasteners or non-factory connector pins, torquing to 'feel', and working without citing the approved maintenance or installation data in the answer.

Installation questions are treated as general workmanship rather than as questions about compliance with specific published limits. The candidate has hands-on habits from the hangar but has not internalized that bend radius, fastener part number, pin part number, torque value, and separation are all specified numbers traceable to approved data.

What to do instead

For any installation item, answer from the controlling document: identify the approved data source first, then state the specific limit (bend radius, torque, separation distance, fastener and contact part numbers). Treat 'snug by feel' and unspecified hardware as automatically wrong, and remember that a substituted connector contact or fastener is an airworthiness issue, not a convenience.

Exam requirements can change. Confirm current details with the exam provider.

NCATT AET practice

199 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Aircraft Fundamentals

    In level, unaccelerated flight, which force directly opposes lift?

    1. Drag
    2. Weight Correct answer.
    3. Momentum
    4. Thrust

    Explanation

    In steady level flight the four forces balance: lift equals weight and thrust equals drag. Lift acts upward, so the force acting directly opposite to it is the aircraft's weight, acting downward through the center of gravity.

  2. Question 2Aircraft Fundamentals

    Which primary flight control surface controls rotation about the longitudinal axis?

    1. Rudder
    2. Elevator
    3. Flap
    4. Aileron Correct answer.

    Explanation

    Ailerons are hinged at the trailing edge of the outer wings and move in opposite directions, producing roll about the longitudinal axis. The elevator controls pitch and the rudder controls yaw.

  3. Question 3Aircraft Fundamentals

    A fuselage in which the skin alone carries the primary loads, with no internal longitudinal members, is called:

    1. Truss
    2. Geodetic
    3. Monocoque Correct answer.
    4. Semimonocoque

    Explanation

    A true monocoque structure carries its primary loads through the outer skin. Semimonocoque designs add stringers and formers to help the skin carry those loads and are far more common in modern aircraft.

  4. Question 4Aircraft Fundamentals

    What is the primary purpose of a circuit breaker in an aircraft electrical system?

    1. Step voltage up or down
    2. Convert AC to DC power
    3. Regulate generator output
    4. Protect wiring from overcurrent Correct answer.

    Explanation

    A circuit breaker opens automatically when current exceeds its rating, protecting wiring and components from overheating. Unlike a fuse, it can be reset after the fault is corrected.

  5. Question 5Aircraft Fundamentals

    Which action is required before fueling an aircraft?

    1. Disconnect the battery charger
    2. Open all cabin circuit breakers
    3. Turn on the cabin lighting
    4. Bond the aircraft before fueling Correct answer.

    Explanation

    Bonding connects the aircraft structure to the fuel source so static charges equalize through a controlled path. Without it, a spark near fuel vapors could cause ignition.

  6. Question 6Aircraft Fundamentals

    On an aircraft drawing, a station number typically identifies:

    1. The drawing revision level
    2. A location along a datum Correct answer.
    3. The part's serial number
    4. The material specification

    Explanation

    Station numbers are measured from a reference datum, usually along the fuselage, so that components can be located consistently during manufacture and repair.

  7. Question 7Aircraft Fundamentals

    Which corrosion type appears as a white or gray powdery deposit on unprotected aluminum?

    1. Stress corrosion
    2. Galvanic corrosion
    3. Intergranular corrosion
    4. General surface corrosion Correct answer.

    Explanation

    Exposed aluminum reacts with oxygen to form a white or gray powdery oxide on the surface. If it is not removed, the attack can progress into pitting and loss of section thickness.

  8. Question 8Aircraft Fundamentals

    Which document is the FAA advisory circular that describes acceptable methods, techniques, and practices for aircraft inspection and repair?

    1. Airworthiness Directive
    2. Type certificate data sheet
    3. AC 43.13-1B Correct answer.
    4. FAA Form 337

    Explanation

    AC 43.13-1B contains the FAA's accepted methods and practices for inspecting and repairing aircraft. It is advisory guidance widely used as the basis for acceptable repairs.

  9. Question 9Aircraft Fundamentals

    Pascal's law states that pressure applied to a confined fluid is:

    1. Transmitted undiminished in all directions Correct answer.
    2. Converted entirely into kinetic energy
    3. Absorbed by the system reservoir
    4. Reduced in proportion to fluid volume

    Explanation

    Pascal's law holds that pressure applied to a confined fluid is transmitted undiminished to every part of the fluid and to the walls of the container. This principle allows a small force on a small piston to produce a large force on a larger piston.

  10. Question 10Aircraft Fundamentals

    On most transport-category aircraft, air for cabin pressurization is normally supplied by:

    1. The hydraulic reservoir
    2. The APU bleed only
    3. Engine compressor bleed Correct answer.
    4. The ram air inlet

    Explanation

    Compressor bleed air is hot and at sufficient pressure to feed the air cycle machines and the pressurization system. The APU can supply bleed air on the ground, but engines are the normal source in flight.

  11. Question 11Aircraft Fundamentals

    An aircraft is loaded so that its center of gravity falls aft of the aft limit. What is the primary concern?

    1. Increased fuel consumption
    2. Reduced pitch stability Correct answer.
    3. Reduced takeoff performance
    4. Higher stall speed

    Explanation

    An aft center of gravity reduces the nose-down moment and can result in marginal or unstable pitch control, and recovery from a stall may become difficult. The aircraft must be loaded within the published CG range.

  12. Question 12Aircraft Fundamentals

    Galvanic corrosion is most likely to occur when:

    1. A protective coating is applied to steel
    2. A single metal is exposed to dry air
    3. An alloy is heat treated above its critical range
    4. Dissimilar metals share a common electrolyte Correct answer.

    Explanation

    When two different metals are joined and wetted by an electrolyte, the more active metal becomes anodic and corrodes preferentially. Preventing moisture from bridging the joint is the main defense.

  13. Question 13Aircraft Fundamentals

    Rotation of an aircraft about its lateral axis is called:

    1. Yaw
    2. Bank
    3. Pitch Correct answer.
    4. Roll

    Explanation

    Pitch is rotation about the lateral, or wing-to-wing, axis and is controlled by the elevator. Roll occurs about the longitudinal axis, and yaw occurs about the vertical axis.

  14. Question 14Aircraft Fundamentals

    AC electrical power on most transport aircraft is generated at which frequency?

    1. 1000 Hz
    2. 50 Hz
    3. 400 Hz Correct answer.
    4. 60 Hz

    Explanation

    Most aircraft AC systems produce 115 V AC at 400 Hz. Higher frequency allows smaller, lighter transformers and motors for a given power rating.

  15. Question 15Aircraft Fundamentals

    What is the function of a shimmy damper on a nose landing gear?

    1. Damp nose wheel shimmy Correct answer.
    2. Retract the gear after takeoff
    3. Lock the gear in the down position
    4. Absorb landing impact loads

    Explanation

    The shimmy damper adds hydraulic damping that resists rapid side-to-side oscillation of the nose wheel during taxi, takeoff, and landing. It does not carry the vertical loads of the aircraft.

  16. Question 16Aircraft Fundamentals

    Why must aircraft fuel tanks be vented?

    1. To keep tank pressure near ambient Correct answer.
    2. To drain accumulated water
    3. To allow fuel transfer between tanks
    4. To vent boost pump output

    Explanation

    Vents keep tank pressure close to ambient as fuel is consumed or as altitude changes. Without venting, a partial vacuum could stop fuel flow or overpressure could damage the tank.

  17. Question 17Aircraft Fundamentals

    What is the primary purpose of a trim tab?

    1. Increase the maximum deflection of the control surface
    2. Relieve control forces in steady flight Correct answer.
    3. Provide aerodynamic balance at high airspeeds
    4. Lock the control surface during ground handling

    Explanation

    A trim tab moves opposite the main control surface, creating a small moment that holds the surface where the pilot wants it. This relieves the control forces the pilot would otherwise have to maintain.

  18. Question 18Aircraft Fundamentals

    In a cabin pressurization system, cabin altitude is controlled primarily by:

    1. The inflow of bleed air
    2. The ram air door
    3. The outflow valve position Correct answer.
    4. The cabin compressor speed

    Explanation

    Conditioned bleed air flows into the cabin continuously, and pressure is regulated by how fast air leaves through the outflow valve. Modulating that valve sets the cabin altitude and rate of change.

  19. Question 19Aircraft Fundamentals

    When a bolt is tightened to a specified torque, the torque value is used as an indirect measure of:

    1. Bolt shear strength
    2. Bolt tension Correct answer.
    3. Thread pitch
    4. Grip length

    Explanation

    Torque stretches the bolt, producing clamping tension. Because friction varies with lubrication and condition, torque is only an approximate indicator of the tension actually achieved.

  20. Question 20Aircraft Fundamentals

    Pitot heat is installed to prevent:

    1. Ice on the windshield
    2. Ice in the fuel lines
    3. Ice blocking the pitot tube Correct answer.
    4. Ice on the wing leading edge

    Explanation

    Ice in a pitot tube blocks ram air pressure, causing the airspeed indicator to behave like an altimeter. Pitot heat keeps the tube clear so airspeed indications remain reliable.

  21. Question 21Aircraft Fundamentals

    A load factor of 3.0 during a maneuver means that the:

    1. Aircraft is climbing at three times its normal rate
    2. Airspeed is three times the normal value
    3. Stall speed is three times the normal value
    4. Structural load equals three times the aircraft's weight Correct answer.

    Explanation

    Load factor is the ratio of total lift to weight, so at 3.0 the structure carries three times the aircraft's weight. Stall speed increases by the square root of the load factor, not by the factor itself.

  22. Question 22Aircraft Fundamentals

    Before two AC generators are connected in parallel, they must be matched in:

    1. Phase and frequency Correct answer.
    2. Voltage and current
    3. Voltage and resistance
    4. Frequency and current

    Explanation

    AC sources can be paralleled only when their output voltages are in phase and at the same frequency. If they are not synchronized, large circulating currents will flow between the generators.

  23. Question 23Aircraft Fundamentals

    A hydraulic fluid sample is reported as NAS 1638 Class 6. This value describes the fluid's:

    1. Maximum allowable moisture content
    2. Viscosity at operating temperature
    3. Particle contamination level Correct answer.
    4. Resistance to foaming

    Explanation

    NAS 1638 defines cleanliness classes by counting particles in specified size ranges per 100 mL of sample. A higher class number means a greater number of contaminant particles.

  24. Question 24Aircraft Fundamentals

    Which design approach removes a component from service at a fixed number of cycles before a crack is expected to form?

    1. Safe-life design Correct answer.
    2. Damage-tolerant design
    3. Fail-safe design
    4. On-condition maintenance

    Explanation

    Safe-life components are given a finite life based on fatigue testing and analysis and are retired before cracks are predicted to initiate. Fail-safe and damage-tolerant designs instead rely on alternate load paths and inspection.

  25. Question 25Aircraft Fundamentals

    In a split-bus electrical system, the bus tie breaker allows the crew to:

    1. Block reverse current from the battery
    2. Limit current to each avionics unit
    3. Convert 115 V AC to 28 V DC
    4. Isolate a faulted source Correct answer.

    Explanation

    Bus tie breakers connect the main buses so either generator can supply both, and they open to isolate a faulted source or to separate the buses. This gives dispatch flexibility and fault isolation.

  26. Question 26Aircraft Fundamentals

    An airplane wing stalls when the:

    1. airspeed exceeds the never-exceed speed
    2. airplane climbs above its service ceiling
    3. flaps are extended beyond 20 degrees
    4. angle of attack exceeds the critical angle Correct answer.

    Explanation

    A wing stalls when the angle of attack exceeds the critical angle, at which point the airflow separates from the upper surface and lift drops sharply. This can happen at any airspeed, weight, or attitude, which is why angle of attack rather than speed defines the stall.

  27. Question 27Aircraft Fundamentals

    In semimonocoque construction, the primary flight loads are carried by the:

    1. the spar carry-through fittings exclusively
    2. a fabric envelope stretched over wooden ribs
    3. the stressed skin, stringers, and frames Correct answer.
    4. an internal truss of welded diagonal tubes

    Explanation

    Semimonocoque structure uses the skin itself as a load-carrying member, with stringers and frames stiffening it and distributing loads to the spars and bulkheads. Because the skin carries shear and tension, damage to it reduces the strength of the structure.

  28. Question 28Aircraft Fundamentals

    Which fastener is designed for installation where only one side of the structure can be reached?

    1. Hi-Lok pin and collar
    2. Hex-head bolt and nut
    3. Solid shank rivet
    4. Blind rivet Correct answer.

    Explanation

    Blind rivets are set from the accessible side only; the far end forms its own shop head against the structure. Solid shank rivets, bolts with nuts, and collar-type fasteners all require access to the back side for bucking or for installing the mating part.

  29. Question 29Aircraft Fundamentals

    Wing dihedral is incorporated primarily to improve:

    1. directional stability
    2. lateral stability Correct answer.
    3. longitudinal balance
    4. longitudinal stability

    Explanation

    With dihedral, a sideslip causes the lower wing to meet the airflow at a greater effective angle of attack than the upper wing, producing a rolling moment that tends to level the wings. This gives positive lateral (roll) stability.

  30. Question 30Aircraft Fundamentals

    An aircraft weighs 3,000 pounds with its center of gravity at 40 inches aft of the datum. A 200-pound item is loaded at a station 60 inches aft of the datum. The new center of gravity is:

    1. 41.25 inches Correct answer.
    2. 43.75 inches
    3. 40.50 inches
    4. 42.00 inches

    Explanation

    Total moment equals 3,000 times 40 plus 200 times 60, or 132,000 pound-inches, and total weight is 3,200 pounds. Dividing moment by weight gives 41.25 inches aft of the datum.

  31. Question 31Aircraft Fundamentals

    In the aluminum designation 2024-T6, the T6 indicates the metal has been:

    1. solution heat-treated and artificially aged Correct answer.
    2. strain-hardened by rolling at the rolling mill
    3. cold worked only, with no thermal treatment
    4. annealed to its softest possible condition

    Explanation

    The T temper prefix denotes a thermally treated alloy, and the 6 shows it was solution heat-treated and then artificially aged to develop strength. Temper designations matter because the same alloy in different tempers has very different strength and formability.

  32. Question 32Aircraft Fundamentals

    The standard flare angle for AN flared tubing fittings is:

    1. 30 degrees
    2. 37 degrees Correct answer.
    3. 60 degrees
    4. 45 degrees

    Explanation

    AN flare fittings use a 37-degree flare, which is the aircraft standard for rigid and flexible fluid lines. A 45-degree flare belongs to the automotive (AC) fitting family and will not seal properly against a 37-degree AN fitting.

  33. Question 33Aircraft Fundamentals

    A balance weight is installed ahead of the hinge line of an elevator primarily to:

    1. reduce the control forces felt by the pilot
    2. keep the surface from fluttering at high speed Correct answer.
    3. increase the maximum elevator deflection angle
    4. hold the surface neutral when the controls are released

    Explanation

    Placing mass ahead of the hinge line moves the surface's center of gravity to or ahead of the hinge, so inertial forces do not drive the surface to increasing deflection. Without that balance, the coupling of structural bending and control-surface motion can sustain flutter.

  34. Question 34Aircraft Fundamentals

    Two wings have equal area and are flown at the same speed and lift coefficient, but one has a higher aspect ratio. The higher-aspect-ratio wing will have:

    1. lower induced drag Correct answer.
    2. higher induced drag
    3. the same induced drag
    4. higher zero-lift drag

    Explanation

    Induced drag is proportional to the square of the lift coefficient divided by aspect ratio, so a longer, narrower wing produces less induced drag for the same lift. This is why sailplanes and long-range aircraft use high-aspect-ratio wings.

  35. Question 35Basic Electricity and Electronics

    A 12-ohm resistor carries a current of 0.5 A. What is the voltage across the resistor?

    1. 6 V Correct answer.
    2. 0.04 V
    3. 12 V
    4. 24 V

    Explanation

    Ohm's law states that voltage equals current multiplied by resistance, V = I x R. Substituting gives 0.5 A x 12 ohms = 6 V.

  36. Question 36Basic Electricity and Electronics

    A 220-ohm resistor and a 330-ohm resistor are connected in series. What is the total resistance of the combination?

    1. 550 ohms Correct answer.
    2. 132 ohms
    3. 130 ohms
    4. 275 ohms

    Explanation

    In a series circuit the same current flows through every component, so the resistances simply add. The total is 220 + 330 = 550 ohms.

  37. Question 37Basic Electricity and Electronics

    Two 100-ohm resistors are connected in parallel. What is the equivalent resistance of the pair?

    1. 100 ohms
    2. 25 ohms
    3. 200 ohms
    4. 50 ohms Correct answer.

    Explanation

    For two equal resistors in parallel, the equivalent resistance is half of one resistor's value because the product-over-sum rule reduces to R/2. Here 100 / 2 = 50 ohms.

  38. Question 38Basic Electricity and Electronics

    A circuit draws 2 A from a 12 V supply. How much power does the circuit dissipate?

    1. 6 W
    2. 0.17 W
    3. 48 W
    4. 24 W Correct answer.

    Explanation

    Electrical power in a DC circuit equals voltage multiplied by current, P = V x I. Multiplying 12 V by 2 A gives 24 W.

  39. Question 39Basic Electricity and Electronics

    A periodic AC signal completes one full cycle every 4 milliseconds. What is its frequency?

    1. 250 Hz Correct answer.
    2. 4 Hz
    3. 2.5 kHz
    4. 40 Hz

    Explanation

    Frequency is the reciprocal of the period, f = 1/T. With T = 0.004 s, f = 1 / 0.004 = 250 Hz.

  40. Question 40Basic Electricity and Electronics

    Four 1.5 V cells are connected in series. What is the total terminal voltage of the battery?

    1. 6 V Correct answer.
    2. 1.5 V
    3. 4.5 V
    4. 0.375 V

    Explanation

    Cells in series add their voltages while sharing the same current. Four cells at 1.5 V each give 4 x 1.5 = 6 V.

  41. Question 41Basic Electricity and Electronics

    What is the primary function of a diode in a circuit?

    1. Pass current in one direction Correct answer.
    2. Amplify the amplitude of a signal
    3. Store energy in an electric field
    4. Convert direct current to alternating current

    Explanation

    A diode is a PN junction that conducts readily when forward biased and blocks current when reverse biased. This one-way conduction is the basis of rectification and circuit protection.

  42. Question 42Basic Electricity and Electronics

    For a fixed wire material and temperature, the resistance of a conductor increases with which of the following?

    1. Increasing length Correct answer.
    2. Lower temperature
    3. Increasing cross-sectional area
    4. Decreasing length

    Explanation

    Resistance is directly proportional to length and inversely proportional to cross-sectional area. A longer wire forces current through more material, so resistance rises.

  43. Question 43Basic Electricity and Electronics

    At a circuit junction, 3 A of current enters and 1.2 A leaves through one branch. Assuming only one other branch leaves the junction, what current flows in that branch?

    1. 1.8 A Correct answer.
    2. 1.2 A
    3. 4.2 A
    4. 0.6 A

    Explanation

    Kirchhoff's current law states that current entering a junction equals current leaving it. The unknown branch therefore carries 3 A - 1.2 A = 1.8 A.

  44. Question 44Basic Electricity and Electronics

    A 12 V source is applied across a series combination of a 1 kilo-ohm and a 3 kilo-ohm resistor. What voltage appears across the 3 kilo-ohm resistor?

    1. 4 V
    2. 3 V
    3. 9 V Correct answer.
    4. 6 V

    Explanation

    In a series voltage divider, each resistor drops a share of the source voltage proportional to its resistance. The 3 kilo-ohm resistor is three-quarters of the 4 kilo-ohm total, so it drops 0.75 x 12 V = 9 V.

  45. Question 45Basic Electricity and Electronics

    Two 10 microfarad capacitors are connected in series. What is the total capacitance?

    1. 5 microfarads Correct answer.
    2. 10 microfarads
    3. 20 microfarads
    4. 2.5 microfarads

    Explanation

    Capacitors in series combine like resistors in parallel, so for two equal values the total is half of one value. The result is 5 microfarads.

  46. Question 46Basic Electricity and Electronics

    A 10 millihenry inductor is used in a circuit operating at 1 kHz. What is its inductive reactance?

    1. 6.28 ohms
    2. 15.9 ohms
    3. 628 ohms
    4. 62.8 ohms Correct answer.

    Explanation

    Inductive reactance is calculated as X_L = 2 pi f L. Using f = 1000 Hz and L = 0.01 H gives 2 x 3.1416 x 1000 x 0.01, which equals about 62.8 ohms.

  47. Question 47Basic Electricity and Electronics

    A sinusoidal voltage has a peak value of 170 V. What is its RMS value?

    1. 85 V
    2. 120 V Correct answer.
    3. 170 V
    4. 340 V

    Explanation

    For a sine wave, RMS voltage equals peak voltage divided by the square root of two. Dividing 170 V by 1.414 gives approximately 120 V.

  48. Question 48Basic Electricity and Electronics

    A transformer with 240 primary turns and 60 secondary turns is supplied with 120 V on the primary. What is the secondary voltage?

    1. 480 V
    2. 30 V Correct answer.
    3. 15 V
    4. 60 V

    Explanation

    The voltage ratio of a transformer equals the turns ratio, Vp/Vs = Np/Ns. Rearranging gives Vs = 120 V x (60 / 240) = 30 V.

  49. Question 49Basic Electricity and Electronics

    What is the decimal equivalent of the binary number 1011?

    1. 9
    2. 11 Correct answer.
    3. 13
    4. 7

    Explanation

    Each binary digit carries a weight of a power of two: 8, 4, 2, and 1. Adding the weights where a 1 appears gives 8 + 0 + 2 + 1 = 11.

  50. Question 50Basic Electricity and Electronics

    Which logic gate produces a HIGH output only when every input is HIGH?

    1. AND Correct answer.
    2. NAND
    3. XOR
    4. OR

    Explanation

    The AND function requires all inputs to be true before its output goes true. Any LOW input forces the AND output LOW.

  51. Question 51Basic Electricity and Electronics

    How must an ammeter be connected to measure the current through a load?

    1. In parallel with the resistor
    2. Across the power supply
    3. In series with the circuit Correct answer.
    4. In parallel with the load

    Explanation

    An ammeter has very low internal resistance and must carry the current being measured, so it is inserted in series with the circuit. Connecting it in parallel would create a low-resistance shunt path and could damage the meter.

  52. Question 52Basic Electricity and Electronics

    What precaution should be taken before using an ohmmeter to measure a resistor in a circuit?

    1. Short the test leads across the source
    2. Raise the circuit current first
    3. Set the meter to the DC volts range
    4. De-energize and isolate it Correct answer.

    Explanation

    An ohmmeter applies its own small internal voltage to determine resistance. External power must be removed and the component isolated so the reading is valid and the meter is not damaged.

  53. Question 53Basic Electricity and Electronics

    What is the purpose of a relay in an aircraft electrical system?

    1. Control a large load with a small signal Correct answer.
    2. Store magnetic energy for later release
    3. Smooth the ripple in a supply output
    4. Convert alternating current into direct current

    Explanation

    A relay uses a small control current through its coil to operate contacts that switch a much larger load current. This allows thin control wiring and remote switching of high-power circuits.

  54. Question 54Basic Electricity and Electronics

    A zener diode operated in reverse breakdown is most commonly used to perform which function?

    1. Emit light when forward biased
    2. Amplify a small signal
    3. Rectify an AC signal
    4. Regulate voltage Correct answer.

    Explanation

    A zener diode maintains a nearly constant reverse voltage across itself once breakdown occurs. This property makes it useful as a shunt voltage regulator or reference.

  55. Question 55Basic Electricity and Electronics

    A series LC circuit contains a 100 microhenry inductor and a 100 picofarad capacitor. At what frequency does it resonate?

    1. 159 kHz
    2. 15.9 MHz
    3. 15.9 kHz
    4. 1.59 MHz Correct answer.

    Explanation

    Resonance occurs when inductive and capacitive reactances are equal, at f = 1 / (2 pi x square root of L x C). With L = 1e-4 H and C = 1e-10 F, the product is 1e-14, its root is 1e-7, and the result is about 1.59 MHz.

  56. Question 56Basic Electricity and Electronics

    What is the capacitive reactance of a 1 microfarad capacitor at 1 kHz?

    1. 159 ohms Correct answer.
    2. 1.59 kilohms
    3. 1.59 ohms
    4. 15.9 ohms

    Explanation

    Capacitive reactance is Xc = 1 / (2 pi f C). Substituting 1000 Hz and 1e-6 F gives 1 / (6.283 x 1e-3), which is about 159 ohms.

  57. Question 57Basic Electricity and Electronics

    A 12 V source has a 4 ohm internal resistance. What load resistance draws maximum power from this source?

    1. 2 ohms
    2. 4 ohms Correct answer.
    3. 12 ohms
    4. 8 ohms

    Explanation

    The maximum power transfer theorem states that a load receives maximum power when its resistance equals the internal source resistance. With 4 ohms internal, the matching load is also 4 ohms.

  58. Question 58Basic Electricity and Electronics

    For an NPN transistor to operate in the active (linear) region, its junctions must be biased in which way?

    1. Reverse biased; forward biased
    2. Reverse biased; reverse biased
    3. Forward biased; reverse biased Correct answer.
    4. Forward biased; forward biased

    Explanation

    The active region requires the base-emitter junction to be forward biased so carriers are injected, and the collector-base junction to be reverse biased so those carriers are swept into the collector.

  59. Question 59Basic Electricity and Electronics

    Two 100-ohm resistors are connected in parallel, and that pair is connected in series with a 50-ohm resistor across a 10 V source. What total current flows from the source?

    1. 0.067 A
    2. 0.10 A Correct answer.
    3. 0.05 A
    4. 0.20 A

    Explanation

    The parallel pair of 100-ohm resistors equals 50 ohms, which adds to the series 50-ohm resistor for 100 ohms total. Ohm's law then gives 10 V / 100 ohms = 0.10 A.

  60. Question 60Basic Electricity and Electronics

    A current of 2 A flows through a 5 ohm resistor. How much power is dissipated in the resistor?

    1. 20 W Correct answer.
    2. 10 W
    3. 2.5 W
    4. 40 W

    Explanation

    Resistive power dissipation is found from P = I squared times R, so the square of the current is multiplied by the resistance: 2 squared times 5 equals 20 W. The voltage across the resistor, 10 V, gives the same result through P = V times I.

  61. Question 61Basic Electricity and Electronics

    An AC generator produces a waveform with a frequency of 400 Hz. What is the period of one complete cycle?

    1. 2.5 ms Correct answer.
    2. 4 ms
    3. 0.4 ms
    4. 25 ms

    Explanation

    Period is the reciprocal of frequency, so T equals 1 divided by f. Dividing 1 by 400 gives 0.0025 seconds, which is 2.5 milliseconds.

  62. Question 62Basic Electricity and Electronics

    Which hexadecimal value is equivalent to the binary number 1101 0111?

    1. D7 Correct answer.
    2. D6
    3. 7D
    4. B7

    Explanation

    Each group of four binary bits converts to exactly one hexadecimal digit using weights 8, 4, 2 and 1. The group 1101 equals 13, which is D, and the group 0111 equals 7, so the result is D7.

  63. Question 63Basic Electricity and Electronics

    A 10 microfarad capacitor is charged to a potential difference of 50 V. How much charge is stored?

    1. 50 microcoulombs
    2. 5 millicoulombs
    3. 500 microcoulombs Correct answer.
    4. 0.2 millicoulombs

    Explanation

    The charge on a capacitor is the product of its capacitance and the voltage across it, Q = C times V. Multiplying 10 microfarads by 50 V gives 500 microcoulombs.

  64. Question 64Basic Electricity and Electronics

    A total current of 6 A enters a parallel combination of a 2 ohm resistor and a 4 ohm resistor. What current flows through the 4 ohm resistor?

    1. 4 A
    2. 3 A
    3. 2 A Correct answer.
    4. 1.5 A

    Explanation

    In a parallel branch, current divides inversely with resistance, so the larger resistance carries the smaller share. The 4 ohm branch takes 2 divided by the 6 ohm total, or one third of the 6 A, which is 2 A.

  65. Question 65Basic Electricity and Electronics

    A transistor operating in its active region has a current gain (beta) of 100 and a base current of 50 microamperes. What is the collector current?

    1. 2 mA
    2. 0.5 mA
    3. 5 mA Correct answer.
    4. 50 mA

    Explanation

    In the active region the collector current equals beta times the base current. Multiplying 100 by 50 microamperes gives 5000 microamperes, which is 5 milliamperes.

  66. Question 66Basic Electricity and Electronics

    A series circuit contains 30 ohms of resistance and 40 ohms of capacitive reactance. What is the magnitude of the total impedance?

    1. 70 ohms
    2. 50 ohms Correct answer.
    3. 10 ohms
    4. 35 ohms

    Explanation

    Resistance and reactance in series add as vectors at right angles, so the impedance magnitude is the square root of R squared plus X squared. The square root of 900 plus 1600 is the square root of 2500, which is 50 ohms.

  67. Question 67Basic Electricity and Electronics

    An ideal parallel LC tank circuit is driven exactly at its resonant frequency. How does the circuit appear to the driving source?

    1. As a pure capacitance
    2. As a short circuit
    3. As a low resistance
    4. As a high resistance Correct answer.

    Explanation

    At resonance the inductive and capacitive reactances are equal in magnitude, so the reactive currents circulate between coil and capacitor and cancel at the terminals. The source therefore sees only the parallel loss resistance, which is a maximum impedance that behaves resistively.

  68. Question 68Basic Electricity and Electronics

    A 24 V source with a 6 ohm series resistance drives a 3 ohm load. What are the Thevenin voltage and Thevenin resistance of the source network as seen by the load?

    1. 24 V and 6 ohms Correct answer.
    2. 8 V and 6 ohms
    3. 8 V and 2 ohms
    4. 24 V and 9 ohms

    Explanation

    Thevenin voltage is the open-circuit voltage at the load terminals; with the load removed no current flows, so there is no drop across the 6 ohm resistance and the terminals stand at 24 V. Thevenin resistance is found by replacing the source with a short, leaving only the 6 ohm resistance across the terminals.

  69. Question 69Digital Techniques and Aircraft Computers

    Convert the binary number 1011 to its decimal equivalent.

    1. 15
    2. 11 Correct answer.
    3. 13
    4. 9

    Explanation

    Each bit position carries a power of two, so 1011 equals 1×8 + 0×4 + 1×2 + 1×1 = 11. The weighting runs from the most significant bit on the left to the least significant bit on the right.

  70. Question 70Digital Techniques and Aircraft Computers

    The decimal number 15 is written in hexadecimal as:

    1. 10
    2. E
    3. 1F
    4. F Correct answer.

    Explanation

    Hexadecimal uses sixteen symbols, 0 through 9 plus A through F, where F represents the value 15. A single hex digit therefore covers exactly four binary bits.

  71. Question 71Digital Techniques and Aircraft Computers

    A single flip-flop can store how much information?

    1. One word
    2. One nibble
    3. One byte
    4. One bit Correct answer.

    Explanation

    A flip-flop is a bistable device with two stable output states, so it holds exactly one binary digit. Larger storage units are built by grouping flip-flops together.

  72. Question 72Digital Techniques and Aircraft Computers

    The chief advantage of fiber-optic cable over copper cable in aircraft wiring is:

    1. Immunity to electromagnetic interference Correct answer.
    2. Ability to carry electrical power
    3. Lower connector cost
    4. Easier field repair

    Explanation

    Fiber-optic cable carries information as modulated light, which is unaffected by the electrical and magnetic fields produced by motors, generators, and other wiring. Optical transmission also provides electrical isolation between systems.

  73. Question 73Digital Techniques and Aircraft Computers

    How many bits are contained in one byte?

    1. 32
    2. 4
    3. 8 Correct answer.
    4. 16

    Explanation

    A byte is defined as eight binary digits, which gives 256 possible combinations. It is the standard unit used to describe memory capacity and data width.

  74. Question 74Digital Techniques and Aircraft Computers

    Which type of memory loses its stored contents when electrical power is removed?

    1. ROM
    2. Flash memory
    3. RAM Correct answer.
    4. EPROM

    Explanation

    RAM is volatile because each cell must be continuously powered to hold its state. Volatile memory is used for working data that can be reloaded after power-up.

  75. Question 75Digital Techniques and Aircraft Computers

    The output of a NOT gate, or inverter, is:

    1. The sum of its inputs
    2. The product of its inputs
    3. Always HIGH regardless of the input
    4. The complement of its input Correct answer.

    Explanation

    A NOT gate has a single input and produces the opposite logic level at its output. A HIGH input yields a LOW output and a LOW input yields a HIGH output.

  76. Question 76Digital Techniques and Aircraft Computers

    The two's complement of the 8-bit binary value 00010100 is:

    1. 00010101
    2. 11101101
    3. 11101100 Correct answer.
    4. 11101011

    Explanation

    Form a two's complement by inverting every bit to get 11101011 and then adding 1, which gives 11101100. This represents the negative of the original value, that is, minus twenty.

  77. Question 77Digital Techniques and Aircraft Computers

    An exclusive-OR gate produces a HIGH output when:

    1. Both inputs are HIGH
    2. The inputs are at different levels Correct answer.
    3. The inputs are at the same level
    4. Both inputs are LOW

    Explanation

    The XOR function signals inequality: its output is true only when one input is HIGH and the other is LOW. When both inputs match, the output is LOW.

  78. Question 78Digital Techniques and Aircraft Computers

    A standard ARINC 429 data word is how many bits long?

    1. 64
    2. 16
    3. 24
    4. 32 Correct answer.

    Explanation

    Each ARINC 429 word is a fixed 32 bits containing an 8-bit label, 2-bit source/destination identifier, 19-bit data field, 2-bit sign/status matrix, and one parity bit. The fixed length keeps every transmission self-contained.

  79. Question 79Digital Techniques and Aircraft Computers

    ARINC 429 transmits data using which signalling method?

    1. Manchester biphase
    2. Frequency-shift keying
    3. Bipolar return-to-zero Correct answer.
    4. Pulse-width modulation

    Explanation

    ARINC 429 drives a differential pair through three states, HIGH, LOW, and null, returning to zero between bits, which is described as bipolar return-to-zero. This tri-state signalling allows the same pair to be shared by a transmitter and multiple receivers.

  80. Question 80Digital Techniques and Aircraft Computers

    According to the Nyquist criterion, an analog-to-digital converter must sample an input at a rate of at least:

    1. Half the highest input frequency
    2. The highest input frequency itself
    3. Twice the highest input frequency Correct answer.
    4. Ten times the highest input frequency

    Explanation

    Sampling at less than twice the highest frequency causes aliasing, in which high frequencies appear as false low frequencies in the digitized data. Meeting the two-times rate allows the original signal to be reconstructed.

  81. Question 81Digital Techniques and Aircraft Computers

    A single parity bit appended to a data word allows the receiver to detect:

    1. Correction of single-bit errors
    2. Detection of an even number of bit errors
    3. Correction of two-bit errors
    4. Detection of an odd number of bit errors Correct answer.

    Explanation

    Parity simply records whether the count of 1s is odd or even, so any odd number of flipped bits changes the count and is flagged. Because the receiver cannot tell which bit changed, parity detects errors but never corrects them.

  82. Question 82Digital Techniques and Aircraft Computers

    A shift register performs which function?

    1. Stores a byte permanently with no applied power
    2. Moves stored data one bit position for each clock pulse Correct answer.
    3. Counts clock pulses and stores the running total
    4. Converts parallel data into a fixed analog level

    Explanation

    Each clock pulse transfers the contents of every stage to the next stage in line, so data walks through the register one bit at a time. This makes shift registers useful for serial-to-parallel and parallel-to-serial conversion.

  83. Question 83Digital Techniques and Aircraft Computers

    A multiplexer is used in a digital system to:

    1. Hold data steady until the next clock edge
    2. Select one of several inputs and route it to a single output Correct answer.
    3. Convert analog values into digital codes
    4. Route a single input to one of several outputs

    Explanation

    A multiplexer acts as a digitally controlled selector switch, connecting one of many inputs to a common output under the control of select lines. This lets several sources share a single data path or bus.

  84. Question 84Digital Techniques and Aircraft Computers

    An analog-to-digital converter carries out which conversion?

    1. Serial data to parallel data
    2. Analog voltage to a digital code Correct answer.
    3. Digital codes to an analog voltage
    4. Voltage to current

    Explanation

    An ADC quantizes a continuously varying voltage into discrete binary numbers that a computer can process. Resolution is set by the number of bits in the output code.

  85. Question 85Digital Techniques and Aircraft Computers

    An EPROM device is erased by:

    1. Exposing it to a strong magnetic field
    2. Applying a high-voltage electrical pulse
    3. Exposing its quartz window to ultraviolet light Correct answer.
    4. Overwriting the old contents with new data

    Explanation

    Erasable programmable ROM is cleared by shining ultraviolet light through a transparent window onto the chip, which returns all cells to the erased state. The whole device is erased at once and must then be reprogrammed with a programmer.

  86. Question 86Digital Techniques and Aircraft Computers

    The MIL-STD-1553 data bus operates at a nominal data rate of:

    1. 100 kbps
    2. 1 Mbps Correct answer.
    3. 10 kbps
    4. 10 Mbps

    Explanation

    MIL-STD-1553 is a 1 megabit per second command/response bus that uses Manchester biphase encoding over a shielded twisted pair. Its data words carry 16 bits plus a parity bit.

  87. Question 87Digital Techniques and Aircraft Computers

    Within a microprocessor, the arithmetic logic unit is responsible for:

    1. Holding the address of the next instruction
    2. Performing arithmetic and logic operations Correct answer.
    3. Permanently storing the operating program
    4. Generating the system clock signal

    Explanation

    The arithmetic logic unit contains the combinational circuitry that adds, subtracts, and applies logic functions to operands supplied from registers. Results are returned to registers or memory under control of the instruction decoder.

  88. Question 88Digital Techniques and Aircraft Computers

    The NAND gate is described as a universal gate because:

    1. Any logic function can be built using only NAND gates Correct answer.
    2. It consumes the least power of any gate type
    3. It is the only gate that can invert a signal
    4. It switches faster than any other gate

    Explanation

    A NAND gate is functionally complete, meaning AND, OR, and NOT functions can all be synthesized from NAND gates alone. This lets a manufacturer build an entire logic circuit from a single gate type.

  89. Question 89Digital Techniques and Aircraft Computers

    A position encoder uses Gray code rather than natural binary. The reason is that in Gray code:

    1. All bits change together at each step
    2. Only eight distinct codes are available
    3. Only one bit changes between successive values Correct answer.
    4. The bit weights match those of binary

    Explanation

    Because just one bit changes per step in Gray code, a sensor reading taken while the encoder is in transition can be off by at most the adjacent position. In natural binary several bits change at once and a misread during that instant can produce a grossly wrong value.

  90. Question 90Digital Techniques and Aircraft Computers

    In Boolean algebra, the expression A + (A · B) simplifies to:

    1. A · B
    2. B
    3. A Correct answer.
    4. A + B

    Explanation

    Factoring gives A(1 + B), and since 1 + B is always 1, the expression reduces to A. This rule is known as absorption and shows that the term B cannot change the outcome.

  91. Question 91Digital Techniques and Aircraft Computers

    A JK flip-flop with both J and K held HIGH will, on each active clock edge:

    1. Reset its output to 0 and hold it there
    2. Toggle its output to the opposite state Correct answer.
    3. Set its output to 1 and hold it there
    4. Hold its present state unchanged

    Explanation

    With both inputs asserted the JK device complements its stored state at every clock, which is why it is widely used in counters and frequency dividers. This toggling behaviour removes the invalid-state problem of the simple SR flip-flop.

  92. Question 92Digital Techniques and Aircraft Computers

    For an 8-bit two's complement signed number, the range of values that can be represented is:

    1. -255 to +255
    2. -127 to +127
    3. 0 to 255
    4. -128 to +127 Correct answer.

    Explanation

    In two's complement the most significant bit carries a negative weight, so the negative range extends one step further than the positive range. That gives 256 distinct codes spanning minus 128 through plus 127.

  93. Question 93Digital Techniques and Aircraft Computers

    The binary-coded decimal (BCD) representation of the decimal number 47 is:

    1. 0010 1111
    2. 1011 1001
    3. 0101 0111
    4. 0100 0111 Correct answer.

    Explanation

    In BCD each decimal digit is coded separately as a 4-bit binary group, so 4 becomes 0100 and 7 becomes 0111, giving 0100 0111. Straight binary conversion of the whole value would give a different pattern, which is why the digit-by-digit grouping matters.

  94. Question 94Digital Techniques and Aircraft Computers

    In an aircraft computer, a watchdog timer is used to:

    1. restart the processor if software stops responding Correct answer.
    2. synchronise the internal clock with the bus controller
    3. record the total operating hours of the unit
    4. limit the current drawn during power-up

    Explanation

    A watchdog is a counter that the running software must reset at regular intervals; if the software hangs or a task overruns, the counter expires and forces a processor reset or safe reversion. It is a fault-recovery device rather than a clocking or power-management function.

  95. Question 95Digital Techniques and Aircraft Computers

    A serial data link that can transmit in one direction only is described as:

    1. full duplex
    2. half duplex
    3. multiplex
    4. simplex Correct answer.

    Explanation

    Simplex describes one-way-only transmission, such as a sensor feeding a display with no return path. Duplex terms describe two-way links, and multiplexing describes sharing one medium among several signals rather than a direction of flow.

  96. Question 96Digital Techniques and Aircraft Computers

    A 10-bit analog-to-digital converter has a full-scale input range of 10 volts. Its resolution is approximately:

    1. 1.0 V
    2. 20 mV
    3. 10 mV Correct answer.
    4. 0.1 V

    Explanation

    Resolution equals the full-scale range divided by the number of steps, 2 raised to the bit count. With 10 bits there are 1024 steps, so 10 V divided by 1024 gives about 9.8 mV, normally rounded to 10 mV.

  97. Question 97Digital Techniques and Aircraft Computers

    Manchester encoding is widely used on aircraft data buses because it:

    1. detects and corrects all transmission errors
    2. doubles the effective data rate of the bus
    3. allows simultaneous two-way traffic on one wire
    4. carries the clock information within the data stream Correct answer.

    Explanation

    In Manchester coding every bit period contains a mid-bit transition whose direction represents the bit value, so the receiver can recover timing directly from the waveform without a separate clock line. This self-clocking property keeps the link synchronised and gives a DC-balanced signal.

  98. Question 98Digital Techniques and Aircraft Computers

    Built-in test equipment (BITE) within a line-replaceable unit is provided to:

    1. convert analog sensor outputs into digital words
    2. detect and isolate faults within the unit Correct answer.
    3. measure altitude and airspeed for the flight crew
    4. supply backup power when a bus fails

    Explanation

    BITE monitors internal circuits and signal paths, stores fault codes and reports them so maintenance can identify the failed unit quickly. It supports fault detection and isolation rather than performing the unit's primary measurement or conversion function.

  99. Question 99Digital Techniques and Aircraft Computers

    In a time-division multiplexed data bus, each connected terminal is:

    1. given a fixed time slot in a repeating frame Correct answer.
    2. connected through its own dedicated pair of wires
    3. polled only when it has data to send
    4. assigned a unique transmission frequency

    Explanation

    Time-division multiplexing shares one medium by allocating each terminal a defined slice of time within a repeating frame, so only one terminal transmits at any instant. Frequency allocation and dedicated wiring describe other multiplexing or non-multiplexed arrangements.

  100. Question 100Digital Techniques and Aircraft Computers

    A fly-by-wire computer with three identical channels uses majority voting so that:

    1. a faulty channel is outvoted by the two healthy channels Correct answer.
    2. the fastest channel always controls the outputs
    3. each channel drives a separate control surface
    4. any channel can be removed for maintenance in flight

    Explanation

    With three channels, the outputs are compared and the value agreed by at least two is passed on, so a single failed channel cannot corrupt the command. This provides fault tolerance without the crew having to disconnect the channel.

  101. Question 101Digital Techniques and Aircraft Computers

    A memory device is specified as 32K x 8. How many address lines does it require?

    1. 32
    2. 16
    3. 15 Correct answer.
    4. 8

    Explanation

    The 32K figure is the number of storage locations: 32 x 1024 = 32 768, which is 2 raised to the power 15, so 15 address lines are needed to select a location. The x8 refers to the width of each location in bits and therefore sets the number of data lines.

  102. Question 102Wiring, Connectors, and Terminations

    In the American Wire Gauge (AWG) system, what happens to a conductor as its gauge number increases?

    1. Its diameter increases
    2. Its diameter decreases at first and then increases
    3. Its diameter stays the same while current capacity increases
    4. Its diameter decreases Correct answer.

    Explanation

    AWG numbering is inverse: a larger gauge number designates a smaller conductor. Each increase of six gauge numbers reduces cross-sectional area by roughly half, which also reduces current capacity.

  103. Question 103Wiring, Connectors, and Terminations

    Which flux is acceptable for soldering electrical connections in aircraft wiring?

    1. Zinc chloride acid flux
    2. Hydrochloric acid flux
    3. Rosin or activated rosin flux Correct answer.
    4. Inorganic salt flux

    Explanation

    Rosin-based fluxes are non-corrosive and non-conductive after the joint is made, so they are the accepted type for electrical soldering. Acid and inorganic fluxes leave residues that attack conductors and insulators.

  104. Question 104Wiring, Connectors, and Terminations

    After stripping insulation from a stranded aircraft wire, the conductor should be

    1. Nicked only if the joint will be crimped rather than soldered
    2. Nicked on no more than half of the strands
    3. Slightly nicked on several strands to improve solder flow
    4. Free of nicks, cuts, and missing strands Correct answer.

    Explanation

    Every strand carries a share of the circuit current, so a nick reduces ampacity and creates a stress riser where fatigue cracking begins. Airworthiness guidance requires the conductor to be undamaged after stripping.

  105. Question 105Wiring, Connectors, and Terminations

    Before mating two circular electrical connectors, the technician should verify that

    1. The keyways are aligned and no contacts are bent or pushed back Correct answer.
    2. The contact cavities are packed with dielectric grease
    3. The coupling threads have been coated with anti-seize compound
    4. All retention clips have been removed from the shells

    Explanation

    Connector shells are keyed so they mate in only one orientation, and forcing a misaligned connector bends contacts. Checking key alignment and contact condition before mating prevents damaged contacts and pushed-back pins.

  106. Question 106Wiring, Connectors, and Terminations

    Increasing wire size beyond the minimum required for the circuit's current is done primarily to

    1. Raise the dielectric strength of the insulation
    2. Limit voltage drop and heating on long runs Correct answer.
    3. Reduce the weight of the wire bundle
    4. Increase the capacitance of the circuit

    Explanation

    Resistance is proportional to length and inversely proportional to cross-sectional area, so a long run develops more drop for a given current. Upsizing the conductor keeps the voltage delivered to the load within limits.

  107. Question 107Wiring, Connectors, and Terminations

    Heat-shrink tubing installed over a termination primarily provides

    1. Mechanical locking of the connector coupling ring
    2. Electrical insulation, strain relief, and moisture protection Correct answer.
    3. Additional current-carrying capacity
    4. A conductive path to the airframe structure

    Explanation

    Shrink tubing seals and insulates the joint, and its recovered grip relieves strain on the termination. It is an insulator and does not conduct current or increase ampacity.

  108. Question 108Wiring, Connectors, and Terminations

    In a coaxial cable, the outer braid or shield functions as

    1. The signal return path and electromagnetic shield Correct answer.
    2. A mechanical filler with no electrical role
    3. The center signal conductor
    4. The dielectric spacer between conductors

    Explanation

    Coax carries the signal on the center conductor and returns it on the surrounding shield, whose concentric geometry contains the field. The same shield intercepts external interference before it reaches the center conductor.

  109. Question 109Wiring, Connectors, and Terminations

    A continuity check on an aircraft circuit verifies that

    1. The insulation resistance to ground exceeds a specified value
    2. The circuit breaker trips at its rated current
    3. The wire gauge matches the drawing callout
    4. The conductor path is continuous with low resistance end to end Correct answer.

    Explanation

    Continuity testing drives a small current through the path and measures resistance, revealing opens and high-resistance joints. Insulation condition requires a separate insulation-resistance test at a much higher voltage.

  110. Question 110Wiring, Connectors, and Terminations

    A size 20 crimp contact in a circular connector is designed to accept which wire gauge range?

    1. 8 through 10 AWG
    2. 12 through 14 AWG
    3. 20 through 24 AWG Correct answer.
    4. 26 through 28 AWG

    Explanation

    Contact size numbers correspond closely to the largest wire the barrel accepts, so a size 20 contact crimps 20 AWG down to 24 AWG. Installing wire outside the specified range produces a loose or overfilled crimp.

  111. Question 111Wiring, Connectors, and Terminations

    How should the braided shield of a shielded cable be handled at a connector?

    1. Twisted with the drain wire and soldered to an adjacent signal pin
    2. Cut back and left floating inside the backshell
    3. Spliced to the signal pin alongside the center conductor
    4. Terminated to the connector shell with an approved ferrule Correct answer.

    Explanation

    The shield must be carried through to the shell or backshell so it remains a continuous interference barrier and ground path. It must never be connected to a signal contact, where it would short or inject noise.

  112. Question 112Wiring, Connectors, and Terminations

    As a general rule, the minimum bend radius for an unsupported wire bundle is

    1. One-half the bundle's outside diameter
    2. Two times the bundle's outside diameter
    3. Equal to the bundle's outside diameter
    4. Ten times the bundle's outside diameter Correct answer.

    Explanation

    Airworthiness guidance calls for a bend radius of at least ten times the bundle diameter so conductors and insulation are not overstressed. Tighter bends crush insulation and concentrate strain on the inside of the curve.

  113. Question 113Wiring, Connectors, and Terminations

    A properly made solder connection on aircraft wiring is identified by

    1. A smooth, shiny, concave fillet showing conductor outline Correct answer.
    2. A heavy fillet that completely hides the conductor
    3. A dull, grainy surface with rounded edges
    4. Solder wicked up beneath the wire insulation

    Explanation

    A good joint flows smoothly, wets both surfaces, and forms a concave fillet through which the strands remain visible, confirming full wetting without excess solder. Dull graininess or a hidden conductor indicates a cold joint or solder excess.

  114. Question 114Wiring, Connectors, and Terminations

    When routing electrical wire near hydraulic and fuel lines, the wiring should be

    1. Routed above the fluid lines with a drip separation Correct answer.
    2. Tied directly to the fluid lines to save space
    3. Routed below the lines so any leak drains away from it
    4. Installed in the same clamp block with the fluid lines

    Explanation

    Keeping wiring above fluid lines prevents leaking hydraulic fluid or fuel from soaking insulation and connectors, which degrades insulation and creates a fire hazard. Separation also prevents chafing between the line and the wire.

  115. Question 115Wiring, Connectors, and Terminations

    A ratcheting crimp tool is specified for aircraft terminations because it

    1. Crimps several wires at once for faster assembly
    2. Heats the terminal to fuse the wire in place
    3. Can be adjusted by the operator to suit any terminal
    4. Cannot be opened until a full crimp cycle is completed Correct answer.

    Explanation

    The ratchet mechanism locks the tool closed until the dies have fully seated, guaranteeing a complete crimp on every cycle. This removes operator-dependent variation in crimp height and depth.

  116. Question 116Wiring, Connectors, and Terminations

    The primary purpose of a connector backshell is to

    1. Provide the electrical contact surface for the mating connector
    2. Position and retain the contacts in the insert
    3. Provide strain relief, shield termination, and sealing Correct answer.
    4. Lock the two halves of the connector together

    Explanation

    The backshell clamps the harness, anchors the shield, and, with its grommet and boot, seals the rear of the connector. It carries no signal current and plays no part in holding contacts in the insert.

  117. Question 117Wiring, Connectors, and Terminations

    A contact insertion/removal tool is used to

    1. Measure the insertion depth of the pin in the socket
    2. Release the retention clip so the contact can be removed Correct answer.
    3. Crimp the contact onto the prepared wire
    4. Spread the contact tines to increase retention force

    Explanation

    Contacts are held by a spring clip inside the insert; the tool reaches in and deflects that clip so the contact slides free. Pulling a contact without the tool deforms the clip and destroys retention.

  118. Question 118Wiring, Connectors, and Terminations

    When installing a ring terminal on a terminal stud, the technician should

    1. Tighten by hand and secure the nut with a lock washer only
    2. Use a calibrated torque wrench at the specified value, holding the terminal Correct answer.
    3. Use the longest available wrench to ensure a tight joint
    4. Tighten until the terminal begins to deform, then back off a quarter turn

    Explanation

    Terminal hardware has a specified torque: too little allows a high-resistance joint that overheats, while too much cracks the terminal or strips the stud. Holding the terminal prevents the wire from being twisted as the nut is drawn down.

  119. Question 119Wiring, Connectors, and Terminations

    An insulation resistance test with a megohmmeter is performed to

    1. Confirm the wire gauge matches the drawing
    2. Verify that a circuit breaker trips at rated current
    3. Measure the contact resistance of a crimped splice
    4. Detect moisture, contamination, or chafed insulation Correct answer.

    Explanation

    The tester applies a high DC voltage and measures leakage current to compute insulation resistance; low readings indicate moisture, contamination, or chafed insulation. Sensitive avionics must be disconnected before the test.

  120. Question 120Wiring, Connectors, and Terminations

    D-subminiature connectors are secured to a panel or mating connector by

    1. A push-pull locking collar
    2. Jackscrews threaded into the mating hardware Correct answer.
    3. A bayonet coupling ring
    4. A threaded coupling nut on the plug shell

    Explanation

    D-sub connectors use jackscrews or slide-lock hardware at the flanges to hold the mating halves together and resist vibration. Bayonet rings, push-pull collars, and threaded coupling nuts are features of circular connectors.

  121. Question 121Wiring, Connectors, and Terminations

    Where a wire bundle passes through a hole in a metallic bulkhead, the correct practice is to

    1. Enlarge the hole so the bundle cannot touch the edges
    2. Install a grommet or protective bushing in the hole Correct answer.
    3. Wrap the bundle with tape and pull it snug against the hole
    4. Bond the bundle to the bulkhead with a metallic clamp

    Explanation

    A grommet or bushing gives the bundle a smooth, rounded bearing surface so vibration cannot wear through insulation against a sharp metal edge. Tape alone wears through and leaves the conductor exposed to structure.

  122. Question 122Wiring, Connectors, and Terminations

    Twisting the two conductors of a signal pair reduces magnetic pickup because

    1. The insulation absorbs the interfering magnetic field
    2. The pair acts as a capacitor that shunts noise to ground
    3. The loop area reverses each twist so induced voltages cancel Correct answer.
    4. The twist raises the conductor's resistance to interference

    Explanation

    A magnetic field induces a voltage proportional to the loop area it links; twisting reverses the loop orientation every half turn so successive induced voltages cancel. The technique works by geometry and needs no ground reference.

  123. Question 123Wiring, Connectors, and Terminations

    A solder sleeve (heat-shrink solder splice) is often chosen for aircraft wire repair because it

    1. Eliminates the need to strip insulation from the wires
    2. Can join three or more wires at one junction without a splice body
    3. Requires no heat and is installed by hand pressure alone
    4. Combines a controlled solder joint and an environmental seal Correct answer.

    Explanation

    The sleeve contains a preformed solder ring and sealant rings; controlled heating reflows the solder and shrinks the tubing, sealing both ends. This produces a repeatable joint with strain relief and moisture protection.

  124. Question 124Wiring, Connectors, and Terminations

    A copper terminal lug is bolted directly to an aluminum airframe rib. To prevent galvanic corrosion, the technician should

    1. Coat both surfaces with graphite grease before assembly
    2. Leave the joint unpainted so it can be inspected frequently
    3. Use plated hardware and an approved barrier compound Correct answer.
    4. Omit the washer so the bare metals make direct contact

    Explanation

    Copper and aluminum are far apart on the galvanic series, so in the presence of moisture the aluminum becomes the anode and corrodes. Plated hardware plus a barrier compound separates the metals and blocks the electrolyte path.

  125. Question 125Wiring, Connectors, and Terminations

    A 22 AWG wire is crimped into a size 16 contact whose barrel is specified for 16 through 20 AWG. The result is

    1. No effect, because contact size is independent of wire gauge
    2. An undersized fill in the barrel and a weak, high-resistance joint Correct answer.
    3. A joint that is acceptable if the insulation gap is correct
    4. A joint that is stronger because the wire fills the barrel completely

    Explanation

    Crimp quality depends on the wire bundle filling the barrel so the dies compress metal against metal; too few strands leave voids and low contact force. The correct fix is the specified contact size or an approved reducing splice.

  126. Question 126Wiring, Connectors, and Terminations

    To minimize induced noise in a harness, wires carrying pulsed or high-current power should be

    1. Laced into the same bundle as the signal wires to save space
    2. Routed separately from signal wires and crossed at right angles Correct answer.
    3. Routed parallel and close to the signal wires so the fields cancel
    4. Wrapped around the signal wires to provide shielding

    Explanation

    Magnetic coupling falls off with distance, and crossing at right angles minimizes the loop area the two circuits share. Keeping noisy power conductors in their own bundle is standard installation practice.

  127. Question 127Wiring, Connectors, and Terminations

    Wire identification markings are repeated at intervals along the length of an aircraft wire mainly so that

    1. a wire can be identified anywhere along a bundle Correct answer.
    2. the marking ink can be checked for fading during inspections
    3. the manufacturing batch can be traced after installation
    4. the resistance per foot of the wire can be read directly

    Explanation

    Identification codes are repeated along the wire so any point of the run can be read without tracing the wire from one end to the other. This makes troubleshooting and repair possible in densely packed bundles where both ends are not accessible at the same time. The markings identify the circuit; they carry no resistance or batch data.

  128. Question 128Wiring, Connectors, and Terminations

    The main hazard of stripping insulation with a dull or wrongly sized wire stripper is that it

    1. nicks the conductor strands and weakens the wire Correct answer.
    2. leaves the insulation too soft to grip the contact
    3. removes the plating from the terminal barrel
    4. causes the wire to work-harden and lose conductivity

    Explanation

    A dull or mismatched stripper cuts into the conductor instead of cleanly parting the insulation, producing nicks and partial strand breaks. These defects concentrate stress and vibration loads, and can progress to an open circuit in service. Strip tools should be sized to the wire gauge and adjusted so only insulation is cut.

  129. Question 129Wiring, Connectors, and Terminations

    Cable ties supporting a wire bundle along a straight run should be

    1. pulled as tight as possible to prevent any movement
    2. installed only at the ends of the run
    3. left loose enough that the bundle can slide freely
    4. snug enough to hold the bundle without indenting insulation Correct answer.

    Explanation

    Ties should support the bundle and keep wires together without crushing or cold-flowing the insulation, since indentations create stress points and chafe paths. They are spaced at regular intervals along the run and trimmed flush so the tail cannot cut adjacent wires or a technician's hands.

  130. Question 130Wiring, Connectors, and Terminations

    When several wires in the same bundle must be spliced, the splices are staggered so that

    1. the bundle remains flexible at the splice points
    2. each splice can be tested without opening the bundle
    3. the repair is easier to identify on a wiring diagram
    4. the splices do not bunch up and enlarge the bundle Correct answer.

    Explanation

    Staggering spreads the added stiffness and diameter of the splices along the run, so the bundle keeps a fairly uniform profile and does not form a hard lump that chafes or interferes with clamps. It also separates the splice bodies so an individual repair can be reworked without disturbing its neighbors.

  131. Question 131Wiring, Connectors, and Terminations

    Keying is built into a connector pair in order to

    1. provide a moisture seal between plug and receptacle
    2. ensure the backshell is tightened to the correct torque
    3. lock the contacts into the insert after crimping
    4. prevent two similar connectors from being mated Correct answer.

    Explanation

    Keyways and key positions give each connector pair a unique clocking so that connectors of the same shell size in the same area cannot be plugged into the wrong receptacle. Mating a keyed plug to the wrong receptacle is physically blocked rather than left to technician memory.

  132. Question 132Wiring, Connectors, and Terminations

    A service loop left in the wiring at a connector allows

    1. the connector to be keyed to its mating half
    2. slack for retermination and relief of strain on contacts Correct answer.
    3. the wire to be identified without a marking code
    4. the shield to be grounded at both ends of the run

    Explanation

    A modest loop of slack lets a technician cut back and remake a termination, and it keeps tension off the contacts so vibration and handling are not carried into the crimp. The loop is dressed so it does not chafe against structure or trap moisture.

  133. Question 133Wiring, Connectors, and Terminations

    After a crimped contact is inserted into a connector, light pull on the wire causes the contact to slide rearward out of its cavity. This indicates that

    1. the contact is not locked in place and must be reseated Correct answer.
    2. the contact is correctly seated in the retention clip
    3. the insert has swollen from solvent contamination
    4. the wire was stripped too long for the contact barrel

    Explanation

    A seated contact is held by the insert retention clip and resists a light axial pull; a contact that backs out was not fully inserted or the clip was damaged. The contact should be removed with the proper tool and reinserted until it seats, then rechecked.

  134. Question 134Wiring, Connectors, and Terminations

    A wire carrying a given current at sea level is to be installed in an unpressurized compartment at high altitude. To keep the same conductor temperature margin, the technician should

    1. select a smaller gauge because current rises with altitude
    2. use the same gauge since altitude does not change wire heating
    3. select a larger gauge since thin air cools the wire less Correct answer.
    4. add a second wire in series with the first to share the load

    Explanation

    Conductor temperature depends on how quickly heat leaves the wire, and at altitude the thinner air removes heat less effectively, so a given current produces a higher temperature rise. Wire ampacity tables are therefore derated for altitude, which in practice means a larger gauge or a lower load for the same circuit.

  135. Question 135Wiring, Connectors, and Terminations

    Terminating aluminum wire with a terminal intended for copper wire is unacceptable mainly because

    1. the insulation on aluminum wire melts at a lower temperature
    2. aluminum conducts current too poorly to carry the rated load
    3. copper terminals cannot be crimped with a ratcheting tool
    4. galvanic action and cold flow can overheat the joint Correct answer.

    Explanation

    Aluminum-to-copper joints are a dissimilar metal couple that corrodes in the presence of moisture, and aluminum also creeps under sustained clamp load, so the connection loosens and its resistance climbs. Aluminum wire must be terminated with terminals and splices listed for aluminum, using the specified hardware and procedures.

  136. Question 136Test Equipment, Measurement, and Troubleshooting

    How must a digital multimeter be connected to measure the current flowing through an aircraft cabin lighting circuit?

    1. In parallel with the lamp so that the meter shares the current
    2. Between the circuit and airframe ground with the meter set to the volts function
    3. Across the power supply terminals with the circuit energized
    4. In series with the circuit so that all circuit current passes through the meter Correct answer.

    Explanation

    A current measurement requires the meter's internal shunt to carry the full circuit current, so the meter is inserted in series after the circuit is opened at a convenient point. An ammeter placed in parallel would shunt current around the load through a very low resistance, which can blow the meter fuse or damage the circuit.

  137. Question 137Test Equipment, Measurement, and Troubleshooting

    Before using an ohmmeter to check a wire for continuity, the technician must first do what?

    1. Set the meter to its highest DC voltage range
    2. Warm the conductor above ambient temperature
    3. Apply a test current from the aircraft battery
    4. De-energize the circuit and isolate the wire from other equipment Correct answer.

    Explanation

    An ohmmeter supplies its own small test current and computes resistance from the resulting voltage, so any external voltage will corrupt the reading and can damage the instrument. The wire must also be isolated from parallel paths so that the meter measures only the conductor under test.

  138. Question 138Test Equipment, Measurement, and Troubleshooting

    A continuity check is performed to confirm that a circuit path has which characteristic?

    1. The ability to carry its full rated current
    2. Insulation that can withstand its rated voltage
    3. Valid digital data being transmitted
    4. A low-resistance path from end to end Correct answer.

    Explanation

    A continuity test drives a small current through the path and indicates whether the resistance is low enough for the circuit to conduct. It is a go/no-go check of the conductor path and does not evaluate dielectric strength, data content, or current-carrying capacity.

  139. Question 139Test Equipment, Measurement, and Troubleshooting

    A wrist strap worn while handling avionics line-replaceable units normally contains a series resistor of approximately what value?

    1. 1 kilohm
    2. 10 megohms
    3. 1 megohm Correct answer.
    4. 10 ohms

    Explanation

    The series resistor limits current to a safe level if the wearer accidentally contacts a live circuit while still allowing static charge to bleed off slowly. One megohm is the standard value used for this protective resistor in grounding straps.

  140. Question 140Test Equipment, Measurement, and Troubleshooting

    A time-domain reflectometer is used in avionics maintenance to do what?

    1. Read the frequency of a localizer receiver output
    2. Measure the insulation resistance of a generator winding
    3. Locate opens, shorts, and impedance changes along a coaxial or twisted-pair cable Correct answer.
    4. Verify the torque applied to a coaxial connector

    Explanation

    A TDR launches a short pulse down the cable and displays the reflections caused by impedance discontinuities, so the type and location of a fault can be inferred from the shape and delay of the reflected pulse. It is a distance-to-fault tool, not a resistance or frequency instrument.

  141. Question 141Test Equipment, Measurement, and Troubleshooting

    A properly compensated 10X oscilloscope probe causes the displayed voltage to indicate which value relative to the signal at the probe tip?

    1. Ten times the actual signal voltage
    2. A value reduced by the scope input capacitance
    3. The same value, because attenuation applies only to current
    4. One-tenth of the actual signal voltage Correct answer.

    Explanation

    The 10X probe divides the signal by ten before it reaches the scope input, which raises input impedance and reduces circuit loading. The scope, or the operator, must scale the reading by ten to obtain the true voltage at the probe tip.

  142. Question 142Test Equipment, Measurement, and Troubleshooting

    A signal generator is normally used in avionics troubleshooting to perform which function?

    1. Record bus traffic for later analysis
    2. Measure the insulation resistance of a static discharge path
    3. Inject a known, calibrated signal into a receiver or amplifier to check its response Correct answer.
    4. Determine the distance to a fault in a waveguide

    Explanation

    The generator supplies a stable, known frequency and amplitude so the technician can observe how the unit under test responds to a controlled input. This supports signal tracing and performance checks throughout a receiver or amplifier chain.

  143. Question 143Test Equipment, Measurement, and Troubleshooting

    An insulation resistance test with a megohmmeter is performed to determine which condition?

    1. The current drawn by a starter under load
    2. The condition of the insulation between a conductor and ground or between windings Correct answer.
    3. The inductance of a motor winding
    4. The exact resistance of a bonding jumper in microhms

    Explanation

    A megohmmeter applies a high DC voltage and measures the very small leakage current through the insulation, giving a resistance value that reflects moisture, contamination, or deterioration. A low reading indicates degraded insulation even though a continuity check may look normal.

  144. Question 144Test Equipment, Measurement, and Troubleshooting

    With a landing light energized, a technician measures 1.8 volts between the switch output and the lamp input terminal. What is the most likely interpretation of this reading?

    1. Abnormal resistance exists in the wiring or switch between the two measurement points Correct answer.
    2. The lamp is drawing less current than its rating
    3. The circuit is open, so no current is flowing
    4. The reading is normal because a voltmeter always indicates circuit drop

    Explanation

    A voltage drop measurement made while the circuit is loaded shows the potential lost across the conductors and contacts carrying the current. A drop of 1.8 volts in a lighting circuit indicates excessive resistance in that path, which a plain resistance check may fail to reveal.

  145. Question 145Test Equipment, Measurement, and Troubleshooting

    A voltmeter with comparatively low input impedance is used to measure the voltage across a high-resistance sensor. How will the indicated reading compare with the true voltage?

    1. It will read higher than the true voltage
    2. It will read zero regardless of the circuit
    3. It will read lower than the true voltage because the meter loads the circuit Correct answer.
    4. It will be exactly correct because voltage is independent of the meter

    Explanation

    The voltmeter's input resistance forms a divider with the source resistance, so a low-impedance meter draws appreciable current and pulls the measured node down. The effect becomes significant when the meter impedance is not many times greater than the circuit impedance.

  146. Question 146Test Equipment, Measurement, and Troubleshooting

    A 10X probe connected to the scope calibrator produces a square wave with pronounced overshoot and peaking on each transition. What does this indicate?

    1. The probe is overcompensated and its trimmer capacitor needs adjustment Correct answer.
    2. The display is normal because calibrators always produce ringing
    3. The probe is damaged and must be replaced
    4. The probe is undercompensated and needs added capacitance

    Explanation

    Excessive peaking on the edges shows that the probe's capacitive divider is not matched to the scope input, with too much capacitance in the probe tip circuit. Adjusting the trimmer until the square wave has flat tops and corners corrects the compensation.

  147. Question 147Test Equipment, Measurement, and Troubleshooting

    What is the effect of increasing the gate time on a frequency counter?

    1. It lowers the input impedance of the counter
    2. It shortens the measurement and reduces resolution
    3. It lengthens the measurement interval and improves resolution Correct answer.
    4. It raises the maximum frequency the counter can accept

    Explanation

    The gate time sets how long the counter accumulates input cycles, so a longer gate captures more counts for the same frequency. More counts over a longer interval yields finer resolution and typically better accuracy, at the cost of a slower reading.

  148. Question 148Test Equipment, Measurement, and Troubleshooting

    Why is a clamp-on ammeter preferred for many current checks on aircraft wiring?

    1. It directly reads insulation breakdown voltage
    2. It measures the exact voltage drop across a contact
    3. It measures resistance without disconnecting the circuit
    4. It measures current without disconnecting or opening the conductor Correct answer.

    Explanation

    A clamp meter senses the magnetic field produced by current in the conductor, so the circuit can stay intact and energized during the check. This avoids opening connectors or breaking solder joints just to insert a meter in series.

  149. Question 149Test Equipment, Measurement, and Troubleshooting

    How should built-in test equipment results be interpreted during fault isolation?

    1. BITE generally tests only the functions the designer wired into the test loop Correct answer.
    2. BITE always identifies the exact faulty line-replaceable unit
    3. BITE eliminates any need for external test equipment
    4. BITE tests every wire in the aircraft from end to end

    Explanation

    BITE monitors the parameters and interfaces built into its design, so a pass result does not prove the entire system is healthy. Faults outside the monitored loop, such as damaged wiring or an unpowered unit, may not be reported.

  150. Question 150Test Equipment, Measurement, and Troubleshooting

    The half-split troubleshooting technique involves which action?

    1. Splitting the wiring harness in half for a visual inspection
    2. Testing at a midpoint of the circuit to determine which half contains the fault Correct answer.
    3. Replacing half of the line-replaceable units before testing
    4. Measuring half of the supply voltage at every connector

    Explanation

    Half-splitting divides the circuit into sections and tests at a midpoint, then discards the healthy half and repeats in the suspect half. Each measurement roughly halves the remaining possibilities, minimizing the number of tests needed.

  151. Question 151Test Equipment, Measurement, and Troubleshooting

    When an ARINC 429 databus analyzer is connected to a bus, what signal format should the technician expect to see?

    1. A Manchester-encoded 1 Mbps bus using token passing between terminals
    2. A differential bipolar signal at 12.5 or 100 kbps Correct answer.
    3. An optical signal carried on a duplex fiber pair between two units
    4. A single-ended 28 VDC discrete signal with one receiver per wire run

    Explanation

    ARINC 429 uses a shielded twisted pair carrying a bipolar, return-to-zero differential signal at either 12.5 or 100 kbps. One transmitter drives the bus and multiple receivers can listen, and the analyzer decodes the 32-bit words from that waveform.

  152. Question 152Test Equipment, Measurement, and Troubleshooting

    When using a pitot-static test set to check air data instruments, which practice applies?

    1. Apply pressure and vacuum slowly and within the sequence and limits given in the maintenance manual Correct answer.
    2. Disconnect the static line and leave it open while testing the altimeter
    3. Apply maximum pitot pressure as quickly as possible to check for leaks
    4. Operate the test set with the aircraft pitot heat energized

    Explanation

    Air data instruments and air data computers can be damaged by abrupt pressure changes or by pressures beyond their rated limits, so the manual's sequence, rates, and values must be followed. Slow, controlled application also gives valid leak and accuracy results.

  153. Question 153Test Equipment, Measurement, and Troubleshooting

    A transponder ramp test set is used to perform which function?

    1. Measure the bonding resistance of the transponder mounting tray
    2. Interrogate the transponder and check its reply code, frequency, and power Correct answer.
    3. Test the aircraft pitot heat circuit
    4. Align the weather radar antenna

    Explanation

    The ramp tester transmits interrogation pulses at the proper frequencies and receives the transponder's replies, allowing the technician to verify reply code, reply frequency, and transmitted power. These checks confirm the installation performs within the tolerances required for air traffic control surveillance.

  154. Question 154Test Equipment, Measurement, and Troubleshooting

    A time-domain reflectometer displays a reflection 1.2 microseconds after the pulse leaves the instrument. If the cable velocity factor is 0.70, the distance to the fault is closest to which value?

    1. 413 feet Correct answer.
    2. 1180 feet
    3. 207 feet
    4. 826 feet

    Explanation

    The pulse travels to the fault and back, so only half the elapsed time represents the one-way trip. Using the propagation speed of about 983.6 feet per microsecond times the 0.70 velocity factor gives roughly 688 feet per microsecond, and 0.6 microsecond times that value is about 413 feet.

  155. Question 155Test Equipment, Measurement, and Troubleshooting

    A digital multimeter on the 20 volt range has an accuracy of plus or minus (0.5 percent of reading plus 3 counts), with a display resolution of 0.01 volt on that range. A reading of 12.00 volts is shown. What is the total possible error?

    1. ±0.09 V Correct answer.
    2. ±0.12 V
    3. ±0.06 V
    4. ±0.03 V

    Explanation

    The proportional part is 0.5 percent of 12.00 volts, or 0.06 volt. The count part is three digits in the last displayed place, or 0.03 volt, and the two are added to give a total tolerance of 0.09 volt.

  156. Question 156Test Equipment, Measurement, and Troubleshooting

    A pulse with a rise time of 10 nanoseconds is to be displayed with acceptable fidelity. Using the conventional 0.35 relationship between bandwidth and rise time, what minimum oscilloscope bandwidth is required?

    1. 35 MHz Correct answer.
    2. 350 MHz
    3. 10 MHz
    4. 100 MHz

    Explanation

    The scope's own rise time is approximately 0.35 divided by its bandwidth, so bandwidth equals 0.35 divided by the signal rise time. For a 10 nanosecond edge this gives about 35 MHz, which is the floor before considering margin for accurate amplitude and edge measurement.

  157. Question 157Test Equipment, Measurement, and Troubleshooting

    For a low-frequency analog signal carried in a shielded cable, the cable shield should normally be connected in which way?

    1. Connected to the signal conductor to cancel noise
    2. Left floating at both ends to avoid ground loops
    3. Grounded at one end only Correct answer.
    4. Grounded at both ends to double the shielding effect

    Explanation

    At low frequencies, grounding the shield at one end still shunts capacitively coupled noise to ground while preventing shield current from circulating between two ground points of different potential. Grounding both ends is used at radio frequencies, where the shield's low impedance makes circulating current less of a problem.

  158. Question 158Test Equipment, Measurement, and Troubleshooting

    A signal generator is set to an output of 13 dBm. What power does this represent?

    1. About 130 milliwatts
    2. About 13 milliwatts
    3. About 2 milliwatts
    4. About 20 milliwatts Correct answer.

    Explanation

    Power in dBm equals ten times the base-10 logarithm of the power in milliwatts, so 13 dBm corresponds to 10 raised to the 1.3 power in milliwatts. That value is approximately 20 milliwatts, which for a 50 ohm system corresponds to roughly 1 volt RMS.

  159. Question 159Test Equipment, Measurement, and Troubleshooting

    A test set's calibration label shows that its calibration has expired. What is the correct action?

    1. Use the set if its readings appear reasonable
    2. Reduce the range by half to compensate for drift
    3. Add a correction factor to every reading taken
    4. Remove the set from service and route it for calibration Correct answer.

    Explanation

    Out-of-calibration equipment cannot be assumed to meet its published accuracy, so any measurement taken with it is suspect and may not satisfy airworthiness requirements. The standard practice is to tag the unit out of service and send it for calibration before further use.

  160. Question 160Test Equipment, Measurement, and Troubleshooting

    A differential probe with a common-mode rejection ratio of 80 dB measures a 1 millivolt differential signal riding on a 1 volt common-mode signal. What is the common-mode error referred to the probe input?

    1. About 100 microvolts Correct answer.
    2. About 800 microvolts
    3. About 10 millivolts
    4. About 1 microvolt

    Explanation

    A CMRR of 80 dB corresponds to a rejection ratio of 10,000 to 1 between common-mode and differential gain. Dividing the 1 volt common-mode level by that ratio yields 100 microvolts of input-referred error, which is ten percent of the signal being measured.

  161. Question 161Test Equipment, Measurement, and Troubleshooting

    A technician needs to view a small AC ripple riding on a 28 V DC bus with an oscilloscope. Which input setting should be selected?

    1. DC coupling
    2. 50 ohm input termination
    3. AC coupling Correct answer.
    4. Ground coupling

    Explanation

    AC coupling places a series capacitor at the input that blocks the DC component while passing the ripple, allowing high vertical gain without the 28 V offset driving the trace off screen. DC coupling would pass the full DC level along with the ripple.

  162. Question 162Test Equipment, Measurement, and Troubleshooting

    Before connecting a multimeter in resistance mode to a circuit, the technician should take which action?

    1. Set the meter to its highest DC voltage range
    2. Remove the current fuse from the meter
    3. De-energize and isolate the circuit Correct answer.
    4. Select the diode-check function before measuring

    Explanation

    An ohmmeter supplies its own small test current, so any applied voltage can damage the meter and produce meaningless readings. Parallel paths must also be broken, otherwise current diverted through them makes the resistance read falsely low.

  163. Question 163Test Equipment, Measurement, and Troubleshooting

    A DMM on its 200 mA range has a shunt resistance of 2 ohms. The meter is inserted in series with a circuit drawing 60 mA. What burden voltage does the meter introduce?

    1. 33 mV
    2. 3.3 V
    3. 120 mV Correct answer.
    4. 12 mV

    Explanation

    Burden voltage is the current multiplied by the meter's internal shunt resistance: 0.060 A times 2 ohms equals 0.12 V, or 120 mV. This drop subtracts from the voltage available to the load and can disturb low-voltage circuits.

  164. Question 164Test Equipment, Measurement, and Troubleshooting

    A frequency counter with a timebase accuracy of plus or minus 5 ppm measures a signal known to be exactly 2.000 MHz. Because of timebase error alone, within which range can the displayed reading fall?

    1. 1.999990 to 2.000010 MHz Correct answer.
    2. 2.000000 to 2.000010 MHz
    3. 1.999000 to 2.001000 MHz
    4. 1.999995 to 2.000005 MHz

    Explanation

    Five parts per million of 2.000 MHz is 10 Hz, so the timebase error alone allows the reading to be off by up to 10 Hz in either direction. The uncertainty is proportional to the measured frequency, not a fixed number of counts.

  165. Question 165Test Equipment, Measurement, and Troubleshooting

    A signal is displayed over 3.5 vertical divisions on an oscilloscope set to 0.2 V per division, using a 10X probe. What signal voltage is present at the probe tip?

    1. 2.8 V
    2. 70 V
    3. 0.7 V
    4. 7 V Correct answer.

    Explanation

    The trace represents 3.5 divisions times 0.2 V per division, or 0.7 V at the scope input. Because the 10X probe attenuates the signal by a factor of ten before it reaches the scope, the actual voltage at the tip is 0.7 V times 10, or 7 V.

  166. Question 166Test Equipment, Measurement, and Troubleshooting

    A repetitive pulse train displayed on an oscilloscope appears to slide horizontally across the screen, making measurement difficult. Which action is most likely to stabilize the display?

    1. Set the trigger level to a stable point on the waveform Correct answer.
    2. Switch the input to ground coupling
    3. Decrease the vertical sensitivity
    4. Increase the sweep rate setting

    Explanation

    A sliding display means the sweep is not being started at the same point on each cycle, so the waveform appears to move. Placing the trigger level at a point the waveform reliably crosses on the selected source gives a consistent starting point and a stable trace.

  167. Question 167Test Equipment, Measurement, and Troubleshooting

    A two-wire ohmmeter reads 0.32 ohm across a bonded jumper. Each test lead and its contact contributes 0.14 ohm. What is the actual resistance of the jumper?

    1. 0.04 ohm Correct answer.
    2. 0.46 ohm
    3. 0.18 ohm
    4. 0.28 ohm

    Explanation

    A two-wire measurement places both leads and their contact resistances in series with the item under test, so their total of 0.28 ohm must be subtracted from the 0.32 ohm reading. The result is 0.04 ohm; a four-wire Kelvin meter separates current and sense leads to avoid this error entirely.

  168. Question 168Avionics and Aircraft Systems Installation

    Which practice produces a reliable crimped terminal on an aircraft wire?

    1. Tinning the stripped wire with solder before crimping
    2. Choosing the largest die that will fit the terminal barrel
    3. Using the crimp tool and die specified for that terminal and wire size Correct answer.
    4. Twisting the strands tightly before inserting them into the barrel

    Explanation

    Reliable crimps depend on the tool, die, and terminal being matched to the wire gauge, as called out in the terminal manufacturer's instructions. A crimp made with the wrong die either over-compresses or leaves voids, both of which raise resistance and reduce pull strength. Crimp quality is normally verified by a pull test on a sample.

  169. Question 169Avionics and Aircraft Systems Installation

    Which flux is acceptable for soldering a terminal to a wire in aircraft electrical systems?

    1. Zinc chloride flux
    2. Hydrochloric acid flux
    3. Phosphoric acid flux
    4. Rosin flux Correct answer.

    Explanation

    Only rosin-based fluxes are permitted because their residues are non-corrosive and non-conductive. Acid or chloride fluxes leave hygroscopic residues that continue to attack copper and solder joints long after the connection is made. Any flux residue should also be cleaned from the joint after soldering.

  170. Question 170Avionics and Aircraft Systems Installation

    Wire bundles in an aircraft are generally supported at intervals not exceeding:

    1. 24 inches Correct answer.
    2. 36 inches
    3. 6 inches
    4. 12 inches

    Explanation

    Standard wiring practice limits support spacing to about 24 inches so the bundle is not strained by its own weight or by vibration. Closer spacing is required in high-vibration areas or where the bundle changes direction. Supports must be padded or cushioned so they do not chafe the insulation.

  171. Question 171Avionics and Aircraft Systems Installation

    The primary purpose of static discharge wicks on an aircraft is to:

    1. Reduce drag by smoothing airflow at the tips
    2. Provide a return path for the electrical bus
    3. Increase antenna gain at high frequencies
    4. Bleed accumulated static charge into the surrounding air Correct answer.

    Explanation

    Static wicks provide a controlled point where precipitation static and other accumulated charge can drain off instead of arcing through antennas, windows, or structure. Discharging the airframe in this way reduces radio interference and damage risk. They do not carry operating current.

  172. Question 172Avionics and Aircraft Systems Installation

    The minimum bend radius for an installed wire bundle is normally taken as:

    1. 5 times the bundle outside diameter
    2. 10 times the bundle outside diameter Correct answer.
    3. 2 times the bundle outside diameter
    4. 0.5 times the bundle outside diameter

    Explanation

    Accepted wiring practice uses about ten times the bundle diameter as the minimum bend radius to avoid stretching conductors and stressing insulation. Tighter bends can crack insulation, distort shielding, and push conductors against the bundle's inner edge. Individual manufacturer instructions take precedence where they are more restrictive.

  173. Question 173Avionics and Aircraft Systems Installation

    When routing wire bundles through an area containing hydraulic lines, the preferred practice is to:

    1. Route them alongside the fluid lines
    2. Route them above the fluid lines Correct answer.
    3. Route them below the fluid lines
    4. Route them through the fluid-line clamps

    Explanation

    Wires are routed above fluid lines so that any leak drips away from the harness rather than soaking the insulation and connectors. Adequate clearance also prevents chafing between the harness and the tubing. Fluid-resistant sleeving is used where separation cannot be maintained.

  174. Question 174Avionics and Aircraft Systems Installation

    The most effective way to terminate a cable shield for electromagnetic protection is to:

    1. Bond the shield 360 degrees to the backshell Correct answer.
    2. Ground the shield to a nearby screw
    3. Leave the shield floating at both ends
    4. Pigtail the shield to a single ground wire

    Explanation

    A full circumferential bond keeps the shield's impedance low at high frequencies, where a long pigtail behaves like an inductor and radiates or picks up energy. The backshell bond also carries the shield current over the shortest path to structure. Pigtail terminations are acceptable only where the manufacturer permits them.

  175. Question 175Avionics and Aircraft Systems Installation

    A 22 AWG wire is to be installed in a connector. Which contact size should be used?

    1. Size 20 Correct answer.
    2. Size 8
    3. Size 16
    4. Size 12

    Explanation

    Size 20 contacts are designed for the 20 through 24 AWG range, so a 22 AWG wire fits and crimps correctly. Using an oversized contact leaves the wire loose in the barrel and produces an unreliable crimp. The contact must also match the connector series and the crimp tool die.

  176. Question 176Avionics and Aircraft Systems Installation

    Which practice is correct when installing a coaxial antenna cable?

    1. Splice the coax with a butt connector if it is too short
    2. Keep runs short and avoid tight bends Correct answer.
    3. Route the coax in the same bundle as the generator output lead
    4. Coil the excess cable into a tight loop behind the panel

    Explanation

    Coaxial cable has a specified minimum bend radius, and tight bends crush the dielectric and change the characteristic impedance. Shorter runs reduce signal loss, which matters most at higher frequencies. Excess cable should be dressed in a gentle sweep rather than coiled tightly.

  177. Question 177Avionics and Aircraft Systems Installation

    A circuit breaker protecting an avionics power feed should be selected so that:

    1. Its rating matches the load's peak inrush current
    2. Its rating is far above the wire's current rating
    3. Its rating does not exceed the wire's rating Correct answer.
    4. Its rating is taken only from the equipment nameplate

    Explanation

    The breaker exists to protect the wiring, so its rating must not exceed the current-carrying capability of the smallest wire in the protected circuit. The load's normal current and inrush are then checked to confirm the breaker will not nuisance-trip. Wire size, bundle derating, and ambient temperature all affect the final choice.

  178. Question 178Avionics and Aircraft Systems Installation

    A 28-volt feed to a remotely mounted avionics unit shows excessive voltage drop. The most direct remedy is to:

    1. Shorten the ground strap at the unit
    2. Add a second circuit breaker in parallel
    3. Increase the conductor size for that run Correct answer.
    4. Turn off other equipment to reduce the load

    Explanation

    Voltage drop is proportional to conductor resistance and length, so a larger gauge conductor is the direct fix for a long run. Connector and terminal resistance should also be checked, since a poor joint can mimic an undersized wire. Parallel breakers do not change the conductor's resistance.

  179. Question 179Avionics and Aircraft Systems Installation

    For a VHF communications antenna mounted on the fuselage, the ground plane is provided by:

    1. The coaxial cable shield alone
    2. A separate copper strap run to the avionics rack
    3. The antenna's internal matching network
    4. Bonded metallic aircraft structure beneath the antenna Correct answer.

    Explanation

    A VHF antenna relies on the metal skin and structure under its base to act as the counterpoise, or ground plane, for radiation. That structure must be bonded so the antenna sees a continuous, low-impedance surface. A poor bond raises VSWR and reduces radiated power.

  180. Question 180Avionics and Aircraft Systems Installation

    When installing an avionics unit that requires forced-air cooling, the technician must confirm that:

    1. The inlet and exhaust paths stay unrestricted Correct answer.
    2. Cooling is needed only during ground operation
    3. The unit is wrapped in insulation to retain cool air
    4. The unit is mounted with the exhaust facing upward

    Explanation

    Forced-air cooling depends on unobstructed intake and exhaust so the specified airflow actually passes over the heat sinks. Ducting that is crushed, kinked, or blocked will cause the unit to overheat and shut down. Air filters and fans should also be checked at installation.

  181. Question 181Avionics and Aircraft Systems Installation

    ARINC 429 digital data is normally carried on:

    1. A 75-ohm coaxial cable
    2. A twisted, shielded pair of wires Correct answer.
    3. Three parallel wires with a common return
    4. A single unshielded wire referenced to airframe ground

    Explanation

    ARINC 429 uses a differential, shielded twisted pair so that noise couples equally onto both conductors and cancels at the receiver. The shield is terminated to the connector backshell to keep interference out of the pair. The cable's characteristic impedance and routing rules must be followed to preserve signal integrity.

  182. Question 182Avionics and Aircraft Systems Installation

    Strain relief on a wire bundle entering a connector is used to:

    1. Transfer mechanical loads from the contacts to the structure Correct answer.
    2. Prevent the wires from carrying current in reverse
    3. Improve the shielding effectiveness of the connector
    4. Keep the connector shell electrically isolated

    Explanation

    Strain relief clamps the bundle so that pulling or vibration loads are carried by the aircraft structure rather than by the crimped contacts. Without it, contacts can back out of the connector or wires can break at the crimp. The clamp must be snug but must not crush the insulation.

  183. Question 183Avionics and Aircraft Systems Installation

    An audio system picks up alternator whine after the signal cable shield was grounded at both ends. The most likely correction is to:

    1. Remove the shield from the cable
    2. Replace the shield with a heavier braid
    3. Ground the shield at one end only Correct answer.
    4. Add a third ground point to the shield

    Explanation

    Grounding a low-frequency signal shield at both ends creates a loop that can carry structure currents, and the resulting voltage appears in series with the signal. A single-point shield ground removes that loop while still providing electrostatic protection. The ground should be at the signal source or as the manufacturer specifies.

  184. Question 184Avionics and Aircraft Systems Installation

    To reduce coupling between a high-current DC feeder and a low-level sensor cable sharing the same area, the technician should:

    1. Wrap both cables together in a single shield
    2. Route them in the same conduit without bonding
    3. Tie both cables together so they run parallel
    4. Separate the runs and cross them at 90 degrees Correct answer.

    Explanation

    Physical separation reduces both capacitive and inductive coupling, and crossing at right angles minimizes the area where magnetic fields can link the two circuits. Parallel runs over long distances are the worst case for induced noise. Conduit, if used, must be bonded at both ends to be effective as a shield.

  185. Question 185Avionics and Aircraft Systems Installation

    Before performing an insulation resistance test on an installed wire bundle, the technician must:

    1. Disconnect sensitive avionics equipment from the circuit Correct answer.
    2. Energize the circuit at 28 V to check for shorts
    3. Set the tester to the lowest resistance range
    4. Wet the harness to improve conductivity

    Explanation

    An insulation tester applies a high DC potential that can damage avionics inputs, so equipment must be disconnected or isolated first. The circuit must also be de-energized and confirmed safe before testing. Results are then compared with the minimum value specified for the wire type.

  186. Question 186Avionics and Aircraft Systems Installation

    A crimped contact must be removed from a connector for repair. The correct method is to:

    1. Unscrew the contact from the front of the connector
    2. Cut the wire and leave the contact in place
    3. Pull the wire firmly until the contact releases
    4. Use the specified extraction tool from the rear of the connector Correct answer.

    Explanation

    Crimp contacts are retained by a spring clip or retaining shoulder and release only when the correct tool depresses that feature from the rear. Pulling on the wire deforms the retention clip and damages the contact and the connector. The extracted contact is normally replaced with a new one.

  187. Question 187Avionics and Aircraft Systems Installation

    Terminal nuts on a bus bar should be tightened with a calibrated torque wrench in order to:

    1. Reduce the electrical resistance of the wire
    2. Prevent hardware damage and vibration loosening Correct answer.
    3. Make the joint easier to disassemble later
    4. Ensure the nut bottoms out on the terminal

    Explanation

    Under-torque leaves a joint that loosens under vibration and heats up, while over-torque cracks terminals, strips studs, or crushes hardware. The manufacturer's torque value gives the clamping force that keeps the joint tight without damage. Torque seal is then applied to show the fastener has been checked.

  188. Question 188Avionics and Aircraft Systems Installation

    A permanent method of identifying an aircraft wire is to:

    1. Rely on the wire's position within the bundle
    2. Mark the wire jacket with a grease pencil
    3. Wrap a piece of masking tape around the wire
    4. Install a printed identification sleeve on the wire Correct answer.

    Explanation

    Printed or stamped sleeves are the accepted permanent means of wire identification and survive cleaning, heat, and fluid exposure. Markings must match the aircraft's wiring diagram so maintenance tracing is possible. Temporary methods fade or fall off and leave the circuit unidentifiable.

  189. Question 189Avionics and Aircraft Systems Installation

    Which splice is acceptable for repairing a damaged wire in a low-vibration avionics bay?

    1. A splice made with a next-size-larger barrel
    2. Twisting the bare ends together and taping them
    3. A crimped, insulated splice of the correct wire size Correct answer.
    4. A soldered joint covered with masking tape

    Explanation

    A properly crimped splice with insulation and the correct wire size restores both mechanical and electrical integrity. The splice must also be located where splices are permitted by the maintenance manual. Splice count and location limits are typically spelled out in the approved data.

  190. Question 190Avionics and Aircraft Systems Installation

    When securing an RF coaxial cable with cable ties, the technician should:

    1. Leave the cable unsupported between connectors
    2. Use metal ties for maximum strength
    3. Tighten the ties to compress the dielectric
    4. Use ties or clamps that hold the cable without deforming it Correct answer.

    Explanation

    Coaxial cable must be supported without crushing the dielectric, which would change its impedance and increase loss. Cushioned clamps or ties snugged only enough to hold the cable are appropriate. Support spacing should follow the manufacturer's recommendations.

  191. Question 191Avionics and Aircraft Systems Installation

    Connector keying and clocking features are used to:

    1. Reduce electromagnetic interference at the shell
    2. Speed up the crimping process
    3. Increase the current rating of the connector
    4. Prevent mating a plug into the wrong receptacle Correct answer.

    Explanation

    Keying and clocking arrange pins and shell features so that only the intended plug can be mated to a given receptacle. This prevents cross-connection during maintenance or troubleshooting. The keying arrangement is recorded in the aircraft's wiring documentation.

  192. Question 192Avionics and Aircraft Systems Installation

    Before performing a continuity check on a circuit, the technician should:

    1. Remove the ground strap from the aircraft structure
    2. Leave all circuit breakers closed to complete the path
    3. Apply 115 V AC to verify the circuit is live
    4. De-energize the circuit and isolate it from other equipment Correct answer.

    Explanation

    An ohmmeter supplies its own small test current, so the circuit must be de-energized and isolated to protect both the meter and the technician. Isolation also prevents parallel paths through other equipment from giving false readings. The circuit is then verified against the wiring diagram.

  193. Question 193Avionics and Aircraft Systems Installation

    When routing a wire bundle through an aircraft structure, the minimum bend radius of the bundle should be:

    1. Twenty times the bundle diameter
    2. Ten times the bundle diameter
    3. Fifteen times the bundle diameter
    4. Five times the bundle diameter Correct answer.

    Explanation

    Accepted aircraft wiring practice sets the minimum bend radius of a wire bundle at ten times its outside diameter, which keeps conductors and insulation from being overstressed. Tighter bends can crack insulation, deform contacts, and make future rework difficult.

  194. Question 194Avionics and Aircraft Systems Installation

    The maximum allowable resistance for a bonding jumper that connects an avionics unit case to primary aircraft structure is:

    1. 250 milliohms
    2. 0.25 milliohm
    3. 2.5 milliohms Correct answer.
    4. 25 milliohms

    Explanation

    Equipment bonding to structure is held to a low resistance limit of 2.5 milliohms so that fault current and RF energy have a low-impedance path back to the airframe. A higher resistance defeats the purpose of the bond and can create voltage differences between the unit and structure.

  195. Question 195Avionics and Aircraft Systems Installation

    After adding a new avionics package to an aircraft, the technician revises the electrical load analysis primarily to:

    1. Confirm the generating system can supply the added continuous and intermittent loads Correct answer.
    2. Establish the trip curve for the new unit's circuit breaker
    3. Determine the wire gauge needed for the new unit's power feed
    4. Verify the battery will accept a higher charging current

    Explanation

    A load analysis compares the total connected continuous and intermittent loads against the capacity of the generating sources, so it is the document that proves the added equipment can be powered in all normal and emergency configurations. Wire sizing and circuit protection are separate calculations that follow once adequate capacity is confirmed.

  196. Question 196Avionics and Aircraft Systems Installation

    Unused cavities in a mated, environmentally sealed connector should be:

    1. Fitted with a size-matched sealing plug Correct answer.
    2. Jumpered to the connector shell for grounding
    3. Filled with sealing compound flush with the face
    4. Left open so condensed moisture can drain

    Explanation

    Empty cavities in a sealed connector break the environmental seal and let moisture and contaminants reach the contacts, so each unused cavity is closed with a sealing plug of the correct contact size. Sealing compound and jumpers alter the connector and are not approved practices.

  197. Question 197Avionics and Aircraft Systems Installation

    Two identical avionics channels provide redundancy for a critical function. To preserve that redundancy, the technician should:

    1. Route each channel in a separate bundle along a different path Correct answer.
    2. Route both channels through one connector for common grounding
    3. Twist both channels together to cancel interference
    4. Route both channels in one bundle to simplify inspection

    Explanation

    Redundancy is only effective if a single event, such as a chafed bundle, a fire, or a lightning strike, cannot damage both channels at once, so the channels are kept in separate bundles on separate routes. Combining them in one bundle or connector creates a common failure point.

  198. Question 198Avionics and Aircraft Systems Installation

    When mounting an antenna on the fuselage skin, the technician should apply approved sealant:

    1. Over the entire antenna to protect it from rain erosion
    2. Only to the coaxial connector threads
    3. Around the antenna base to keep moisture out of the fuselage Correct answer.
    4. Between the antenna and the mounting surface to insulate them

    Explanation

    A sealant fillet around the antenna base keeps rain and wash water from entering the mounting holes and the aircraft interior while still allowing the antenna to be removed later. The mounting surface itself must remain an electrical bond to the skin, and the radiating element is never coated.

  199. Question 199Avionics and Aircraft Systems Installation

    A wire bundle must pass through a pressurized bulkhead to reach equipment in an unpressurized bay. The installation should use:

    1. A conduit sleeve bonded to structure at each end of the run
    2. A pressure-tight feedthrough sealed to bundle and bulkhead Correct answer.
    3. A plain grommet with the bundle supported on both sides
    4. A split rubber bushing clamped around the bundle

    Explanation

    Any penetration of a pressure boundary must be closed with a fitting that seals to both the bulkhead and the wire bundle, otherwise the cabin cannot hold pressure. Grommets, bushings, and open sleeves provide chafe protection only and do not seal the pressure vessel.

NCATT AET flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Four forces of flight
Lift, weight, thrust, and drag act on an aircraft in flight; in steady, unaccelerated level flight, lift equals weight and thrust equals drag.
Aircraft control axes
Roll is motion about the longitudinal axis controlled by ailerons; pitch is about the lateral axis controlled by the elevator; yaw is about the vertical axis controlled by the rudder.
Standard sea-level pressure
In the ICAO standard atmosphere, sea-level pressure is 29.92 inches of mercury, or 1013.25 hectopascals, and is used as the altimeter setting reference.
Critical angle of attack
The angle of attack at which airflow separates from the wing and lift decreases abruptly; a stall occurs at this angle regardless of airspeed or attitude.
Pascal's law
Pressure applied to a confined fluid is transmitted undiminished in all directions, so hydraulic force equals pressure multiplied by piston area.
Ohm's law
Voltage equals current multiplied by resistance, written V = IR; it relates voltage, current, and resistance in a linear DC circuit.
Series circuit
A circuit with one current path: current is the same through all components, voltage divides among them, and total resistance is the sum of individual resistances.
Parallel circuit
A circuit with multiple current paths: voltage is the same across each branch, current divides among branches, and total resistance is less than the smallest branch resistance.
RMS value of sine wave
The root-mean-square value of a sine wave equals peak value divided by the square root of two, about 0.707 times peak, and produces equivalent heating.
Capacitor behavior
A capacitor stores energy in an electric field, blocks direct current when charged, and passes alternating current with reactance inversely proportional to frequency and capacitance.
Transformer turns ratio
Primary-to-secondary voltage ratio equals primary-to-secondary turns ratio; an ideal transformer conserves power, so current changes inversely with voltage.
Binary number system
Base-2 numbering using only 0 and 1; each bit position represents a power of two, and eight bits form one byte.
AND gate
A logic gate whose output is 1 only when all inputs are 1; if any input is 0, the output is 0.
Analog-to-digital converter
An ADC samples an analog voltage and quantizes it into discrete binary codes; resolution equals reference voltage divided by two raised to the bit count.
ARINC 429 data bus
A serial avionics data bus using 32-bit words over twisted-pair wiring, commonly at 12.5 or 100 kilobits per second, with one transmitter per bus.
Built-in test equipment
BITE is circuitry and software inside a line-replaceable unit that monitors operation, detects faults, and reports status to maintenance or cockpit systems.
American Wire Gauge
AWG numbers specify conductor size; a larger AWG number means a smaller conductor diameter and higher resistance per unit length.
Crimp termination
A solderless connection made by deforming a metal barrel around a conductor with a calibrated tool; it requires correct wire gauge, insertion depth, and pull test.
Cable shield grounding
A cable shield is typically grounded at one end to provide electrostatic shielding while avoiding ground loops that can induce noise currents.
Coaxial cable
A cable with a center conductor, dielectric, metallic shield, and jacket; impedance is typically 50 or 75 ohms and bends must respect minimum radius.
Environmental splice
A sealed wire splice using a crimp barrel and heat-shrink sleeve with adhesive that excludes moisture and provides strain relief.
Connector keying
Mechanical features on mating connectors that prevent incorrect engagement; keyways and clocking ensure pins mate only with their intended sockets.
Measuring current with multimeter
The meter is connected in series with the circuit so current flows through it; the circuit must be opened and the correct current range selected.
Oscilloscope probe compensation
Adjusting a probe's trimmer capacitor to match the oscilloscope input so a square wave displays flat tops, ensuring accurate amplitude and pulse response.
Megohmmeter
An instrument that applies a high DC test voltage to measure insulation resistance; the circuit must be de-energized and isolated before testing.
Time-domain reflectometer
A TDR sends pulses into a cable and measures reflections to locate opens, shorts, and impedance changes, displaying distance based on propagation velocity.
Voltage drop test
Measuring voltage across a connection or conductor while current flows; excessive drop indicates high resistance such as a corroded or loose termination.
Line replaceable unit
An avionics component designed to be removed and replaced as a unit on the aircraft, with standardized mounting, connectors, and built-in test capability.
Voltage standing wave ratio
VSWR measures impedance match in an antenna system; a value near 1:1 is ideal, while higher values indicate reflected power and reduced efficiency.
Aircraft bonding
Low-resistance electrical connection between aircraft structures and components that provides a return path and controls static discharge and lightning current.
400 Hz aircraft power
Many aircraft use 115-volt alternating current at 400 hertz instead of 60 hertz, allowing smaller transformers and motors for the same power.
Antenna ground plane
A conductive surface beneath an antenna that provides the reference for radiation; its size and bonding affect radiation pattern and impedance.

NCATT AET study guide

Aircraft Fundamentals

Core concepts

An aircraft in steady flight balances four forces: lift, weight, thrust and drag. Lift rises with angle of attack, airspeed squared, air density and wing area, up to the stall. Induced drag falls as speed increases; parasite drag rises with speed squared. Primary controls are ailerons (roll), elevator (pitch) and rudder (yaw); flaps raise lift and drag, and trim tabs relieve stick forces.

Structures may be truss, monocoque or semimonocoque. Stressed-skin semimonocoque designs use spars, ribs, stringers, formers and bulkheads. Common materials include 2024 and 7075 aluminum alloys, rivets, and composite or honeycomb structures. Know the corrosion types - surface, galvanic, pitting, intergranular, exfoliation and stress - and that dissimilar metals plus moisture drive galvanic attack.

Weight and balance uses a datum, arms and moments: moment = weight x arm; CG = total moment / total weight. The CG must stay inside forward and aft limits. A forward CG raises stall speed and gives a nose-down tendency; an aft CG reduces static stability. Standard sea-level atmosphere is 15 C and 29.92 inHg, with roughly a 2 C per 1,000 ft lapse rate.

Traps

Questions deliberately confuse angle of attack with airspeed, mix up induced and parasite drag, or ask which control moves for a given motion. Weight-and-balance items often hide a datum offset or a negative arm.

Worked example

A 2,000 lb aircraft has its CG at 30 in. Add 200 lb at arm 40 in. New moment = (2,000 x 30) + (200 x 40) = 68,000 lb-in; new weight = 2,200 lb; new CG = 68,000 / 2,200 = 30.9 in - the CG moves aft.

Basic Electricity and Electronics

Core concepts

Voltage is electrical pressure, current is charge flow, and resistance opposes current. Ohm's law gives V = I x R; power is P = V x I = I squared x R = V squared / R. In series, current is common, voltages add and resistances add. In parallel, voltage is common, currents add, and total resistance is the reciprocal sum; for two resistors, R = R1 x R2 / (R1 + R2). Kirchhoff's voltage law sums loop voltages to zero, and the current law sums currents at a node to zero.

AC signals have period, frequency, peak, peak-to-peak and RMS values. For a sine wave, RMS = 0.707 x peak and average = 0.637 x peak; 115 V aircraft AC is an RMS value. Capacitive reactance falls as frequency rises; inductive reactance rises with frequency. Impedance combines resistance and reactance. Transformers trade voltage for current by turns ratio while conserving power. Diodes rectify, transistors switch or amplify, and batteries in series add voltage while parallel cells add capacity.

Traps

The most common errors are treating a peak value as RMS, adding parallel resistances directly, and assuming current is the same in parallel branches. Watch for questions about reactance versus frequency and whether a transformer steps voltage up or current up.

Worked example

A 28 V DC bus feeds a 7 ohm load. I = V / R = 4 A; P = V x I = 112 W. If the same circuit drew 2 A, the power would be 56 W - power scales with current for a fixed voltage.

Digital Techniques and Aircraft Computers

Core concepts

Digital systems represent values in binary; a byte is 8 bits, and a word is the processor's natural width. Convert binary to hex in groups of four bits, and hex to decimal by place value. Logic gates - AND, OR, NOT, NAND, NOR, XOR - are described by truth tables. Combinational logic has no memory, while flip-flops and registers are sequential.

Aircraft data buses matter. ARINC 429 is a one-way, point-to-point bus using 32-bit words. MIL-STD-1553 is a bidirectional command/response bus, usually dual-redundant, with a bus controller and remote terminals. ARINC 629 is bidirectional, and ARINC 664 is Ethernet-based. LRUs communicate through these buses rather than by direct wiring.

Computers use ADCs and DACs to bridge analog and digital worlds; resolution and sampling rate limit accuracy. Memory divides into RAM (volatile) and ROM (non-volatile). Built-in test is power-up (PBIT), initiated (IBIT) or continuous (CBIT). Software is controlled by part number and configuration.

Traps

Questions often reverse bus direction or mix ARINC 429 with 1553. Binary and hex conversions and gate outputs are common, as is assuming a data bus is a power wire.

Worked example

Convert 1011 0110 to hex: split into 1011 and 0110 = B and 6, so 0xB6. Decimal = 128 + 32 + 16 + 4 + 2 = 182.

Wiring, Connectors, and Terminations

Core concepts

A wire is a conductor, insulation and often a shield. American Wire Gauge numbers run inversely: a larger AWG number means a smaller conductor with less current capacity. Select wire for current, voltage drop, temperature, altitude and bundle derating. Voltage drop = current x loop resistance; keep it within the equipment limit.

Connectors may be circular, rectangular or D-subminiature, with pins and sockets, keying and coupling threads. Crimped contacts need the correct tool and a pull check; soldering needs clean surfaces and no acid flux. Terminal lugs, splices and shield terminations must be mechanically sound and insulated. Shields are normally grounded at one end to avoid ground loops, following the installation instructions.

Route wiring with adequate support, protection from chafing and heat, and separation between power and sensitive signal wires. Observe minimum bend radius, commonly about ten times the cable diameter, keep coax bends gentle, and identify circuits clearly.

Traps

Expect questions on AWG direction, crimp versus solder, shield grounding at one versus both ends, and using the wrong flux or tool. Bigger number meaning bigger wire is a classic wrong answer.

Worked example

A 10 A load flows through a 0.05 ohm run. Voltage drop = 10 x 0.05 = 0.5 V. On a 28 V bus that is about 1.8 percent - acceptable for most loads, but repeat the check after any connector or splice is added.

Test Equipment, Measurement, and Troubleshooting

Core concepts

The multimeter measures voltage, current, resistance, continuity and diode drop. A voltmeter goes in parallel and should have high impedance; an ammeter goes in series and has low resistance. Never measure resistance or continuity on a powered circuit. True-RMS meters matter for distorted waveforms; average-responding meters misread them.

An oscilloscope shows amplitude versus time; set volts/div, time/div and trigger, and use a 10x probe with compensation. A megohmmeter checks insulation resistance, a bond meter measures very low resistance in milliohms, and a time-domain reflectometer locates opens, shorts and mismatches in coax. Signal generators, frequency counters, logic analyzers and spectrum analyzers extend the toolkit.

Troubleshoot logically: confirm power and grounds, inspect connectors, half-split the circuit, substitute known-good LRUs, and compare with a known-good system. Read built-in test codes before replacing parts.

Traps

Typical traps are using an ohmmeter on a live circuit, connecting an ammeter in parallel, confusing peak and RMS, and forgetting the round trip in TDR measurements.

Worked example

A TDR pulse reflects after 1.0 microsecond in coax with velocity factor 0.7. Distance = (0.7 x 3 x 10^8 m/s x 1.0 x 10^-6 s) / 2 = 105 m. The divide-by-two accounts for the trip out and back.

Avionics and Aircraft Systems Installation

Core concepts

Avionics installation begins with approved data: wiring diagrams, equipment location, power budget and weight-and-balance impact. Each LRU needs a proper rack or mount, correct connectors, keying and torque, plus enough cooling and vibration isolation. Power feeds should be protected by a breaker or fuse sized to protect the wire and carry the load; avionics often use a dedicated bus.

Grounding and bonding control noise and provide fault return. Use single-point grounding where specified, bond the airframe, and avoid ground loops. Shielded and twisted wires, separation from high-current cables, and careful coax routing reduce EMI. Antennas need a proper ground plane, a clear view and low-loss cable; check VSWR after installation.

Document the work, update the weight and balance, load the correct software and configuration, and perform functional and operational checks before return to service.

Traps

Questions test breaker sizing (protect the wire, not just the load), shield termination, antenna cable loss, connector torque, and whether power was removed before work. Do not assume a larger breaker is safer.

Worked example

An avionics package draws 8 A on a 28 V bus. Choose a breaker above the load but at or below the wire's ampacity - for example, a 10 A breaker with wire rated at least 10 A in the installed bundle - then verify voltage drop at the LRU connector.

NCATT AET cheat sheet

Quick reference

Aircraft Fundamentals

  • Four forces act on an aircraft: lift, weight, thrust, and drag; in steady, unaccelerated level flight, lift equals weight and thrust equals drag.

  • Roll is motion about the longitudinal axis and is controlled by ailerons; pitch is about the lateral axis and is controlled by the elevator; yaw is about the vertical axis and is controlled by the rudder.

  • Lift increases with angle of attack up to the critical angle, where airflow separates and the wing stalls; a stall can occur at any airspeed or attitude.

  • The ICAO standard atmosphere at sea level is 15 degrees Celsius, 29.92 inches of mercury or 1013.25 hectopascals, with a tropospheric lapse rate near 2 degrees Celsius per 1000 feet.

  • Pitot pressure is total pressure; static pressure is ambient pressure; the airspeed indicator uses the difference between them, while the altimeter and vertical speed indicator use static pressure.

  • Pascal's law states that pressure applied to a confined fluid is transmitted undiminished in all directions; hydraulic force equals pressure times piston area.

  • Semimonocoque structure uses stressed skin supported by stringers and frames; loads are carried by the skin, stringers, and frames together rather than by the skin alone.

  • A turbine engine has intake, compressor, combustor, turbine, and exhaust sections; a turbofan also has a bypass duct and is characterized by its bypass ratio.

Quick reference

Basic Electricity and Electronics

  • Ohm's law: V = IR; power relationships include P = VI, P = I squared R, and P = V squared divided by R.

  • Series circuits have one current path: current is identical through all components, voltage divides, and total resistance is the sum of individual resistances.

  • Parallel circuits have multiple current paths: voltage is identical across each branch, current divides, and total resistance is found from the reciprocal sum of branch resistances.

  • Kirchhoff's current law states that the algebraic sum of currents entering a node is zero; Kirchhoff's voltage law states that the algebraic sum of voltages around a closed loop is zero.

  • For a sine wave, frequency equals one divided by period; RMS value equals peak value divided by the square root of two, about 0.707 times peak.

  • Capacitive reactance is XC = 1 divided by 2 pi f C; inductive reactance is XL = 2 pi f L; impedance magnitude is the square root of R squared plus the square of XL minus XC.

  • A capacitor stores energy in an electric field and blocks direct current while passing alternating current; an inductor stores energy in a magnetic field and opposes changes in current.

  • In an ideal transformer, primary-to-secondary voltage ratio equals the turns ratio, and power is conserved so current changes inversely with voltage.

Quick reference

Digital Techniques and Aircraft Computers

  • Binary is base 2 and uses only 0 and 1; each bit position represents a power of two, and eight bits form one byte; hexadecimal is base 16.

  • In two's complement representation, a negative number is formed by inverting all bits of the positive value and adding one.

  • AND outputs 1 only when all inputs are 1; OR outputs 1 when any input is 1; NOT inverts; XOR outputs 1 only when inputs differ.

  • Combinational logic output depends only on present inputs; sequential logic uses memory elements such as flip-flops and changes state on a clock edge.

  • An analog-to-digital converter samples and quantizes an analog voltage into binary codes; resolution equals reference voltage divided by two raised to the number of bits.

  • ARINC 429 is a serial avionics bus using 32-bit words over twisted-pair wiring, commonly at 12.5 or 100 kilobits per second, with one transmitter per bus.

  • A line-replaceable unit is an avionics component designed for removal and replacement on the aircraft; built-in test equipment monitors its operation and reports faults.

  • RAM is volatile memory that loses data when power is removed; ROM and flash are nonvolatile and retain stored data without power.

Quick reference

Wiring, Connectors, and Terminations

  • American Wire Gauge numbers specify conductor size; a larger AWG number means a smaller conductor diameter and higher resistance per unit length.

  • A crimp termination is made by deforming a metal barrel around a conductor with a calibrated tool; correct wire gauge, insertion depth, and pull strength are required.

  • Cable shields are typically grounded at one end to provide electrostatic shielding while avoiding ground loops that can carry induced noise currents.

  • Coaxial cable has a center conductor, dielectric, metallic shield, and jacket; impedance is commonly 50 or 75 ohms, and minimum bend radius must be observed.

  • Connector keying and clocking prevent incorrect mating; keyways ensure pins engage only with their intended sockets.

  • Environmental splices use a crimp barrel with an adhesive-lined heat-shrink sleeve to exclude moisture and provide strain relief.

  • Twisted-pair wiring and shielded cables reduce electromagnetic interference; signal wires are routed separately from high-power and high-current cables.

  • Terminal lugs must be matched to stud size, installed with the specified torque, and checked for security; loose or over-torqued terminations cause high resistance or damage.

Quick reference

Test Equipment, Measurement, and Troubleshooting

  • A multimeter measures voltage in parallel with the circuit, current in series with the circuit, and resistance only in a de-energized circuit.

  • An oscilloscope displays voltage versus time; volts per division sets vertical scale, time per division sets horizontal scale, and the ground clip provides the reference.

  • Probe compensation adjusts the probe's trimmer capacitor to match the oscilloscope input so a square wave displays flat tops and accurate amplitude.

  • A megohmmeter applies a high DC test voltage to measure insulation resistance; the circuit must be de-energized and isolated before testing.

  • A time-domain reflectometer sends pulses into a cable and analyzes reflections to locate opens, shorts, and impedance changes.

  • Voltage-drop testing measures voltage across a connection while current flows; excessive drop indicates high resistance such as a corroded or loose termination.

  • Half-split troubleshooting divides a system into sections, tests at the midpoint, and continues dividing the faulty section to isolate the fault efficiently.

  • Before working on avionics, discharge stored energy in capacitors, use lockout and tagout, and follow electrostatic discharge precautions for sensitive components.

Quick reference

Avionics and Aircraft Systems Installation

  • Many transport aircraft use 28-volt DC and 115-volt 400-hertz AC electrical power; 400-hertz AC allows smaller transformers and motors than 60-hertz AC.

  • An antenna requires an adequate conductive ground plane and a good bond to the airframe; poor bonding or ground plane size affects radiation pattern and impedance.

  • Voltage standing wave ratio indicates impedance match in an antenna system; a value near 1:1 is ideal, and higher values indicate reflected power.

  • A line-replaceable unit installation requires correct part number and configuration, secure rack mounting, properly mated connectors, and adequate cooling airflow.

  • Aircraft bonding provides low-resistance electrical connections between structures and components for fault current return, static discharge control, and lightning protection.

  • Avionics cooling must maintain airflow and temperature limits; blocked filters, failed fans, or inadequate clearances can cause overheating and intermittent faults.

  • Wire bundles are routed with clamps and chafe protection, away from hot surfaces, fuel lines, and high-current cables, and must respect minimum bend radius.

  • Pitot and static systems require leak checks and correct port alignment; obstruction or leakage causes inaccurate airspeed, altitude, and vertical speed indications.

NCATT AET key terms

Angle of attack

The angle between an airfoil's chord line and the direction of the relative wind. Increasing it increases lift up to the critical angle, beyond which the wing stalls.

Related: Load factor, Bernoulli's principle
Center of gravity

The point where the aircraft's total weight is considered to act. It must remain within published forward and aft limits for stable, controllable flight.

Related: Load factor, Station numbering
Pitot-static system

A system of probes and ports that supplies impact (pitot) pressure and undisturbed static pressure to airspeed, altitude, and vertical speed instruments, and to air data computers.

Related: Bernoulli's principle
Load factor

The ratio of total lift produced by an aircraft to its gross weight, expressed in Gs. Higher load factors increase structural stress and raise stall speed.

Related: Angle of attack, Center of gravity
Bernoulli's principle

In a steady flow of fluid, an increase in speed is accompanied by a decrease in pressure. This explains how airfoils produce lift and how venturi instruments work.

Related: Pitot-static system, Angle of attack
Station numbering

A coordinate system of fuselage stations, wing stations, buttock lines, and waterlines used to locate components and wire routing points on a specific aircraft model.

Related: Wire separation
Ohm's law

The relationship stating that current equals voltage divided by resistance (I = E/R). Technicians use it to calculate expected values when troubleshooting a circuit.

Related: Voltage drop test, Impedance
Impedance

The total opposition a circuit presents to alternating current, combining resistance with capacitive and inductive reactance. It is measured in ohms and varies with frequency.

Related: Ohm's law, Coaxial cable
Rectifier

A device, usually made of diodes, that converts alternating current into pulsating direct current. Aircraft DC systems often use rectifiers fed from AC generators.

Related: Capacitor, Transformer
Capacitor

A component that stores energy in an electrostatic field between two conductors separated by a dielectric. It blocks DC while passing AC and is used for filtering and timing.

Related: Inductor, Rectifier
Inductor

A coil that stores energy in a magnetic field and opposes changes in current. Its opposition, called inductive reactance, increases as frequency increases.

Related: Capacitor, Transformer
Transformer

A device with two or more coils coupled by a magnetic core that changes AC voltage and current levels through mutual induction, without a direct electrical connection between windings.

Related: Inductor, Rectifier
Electrical ground (return path)

The common return path in an electrical circuit. In aircraft, the metal structure often serves as ground, so one wire can feed a component and current returns through the airframe.

Related: Bonding jumper, Shield termination
Circuit breaker

A resettable protective device that opens a circuit automatically when current exceeds a rated value, protecting wiring from overheating. Unlike a fuse, it can be reset after the fault is corrected.

Related: Multimeter, Voltage drop test
Binary number system

A base-2 numbering system using only the digits 0 and 1. Digital computers represent all data and instructions as patterns of binary bits.

Related: Logic gate, Analog-to-digital converter
Logic gate

A circuit that produces a specific output based on combinations of digital inputs, following rules such as AND, OR, NOT, NAND, and NOR.

Related: Binary number system
Analog-to-digital converter

A circuit that samples a continuously varying voltage and converts it into a digital number a computer can process, for example when digitizing a sensor output.

Related: Binary number system, Data bus
ARINC 429

A widely used one-way digital data bus standard in which a single transmitter sends 32-bit words to up to 20 receivers over a twisted, shielded pair.

Related: Data bus, Line replaceable unit
Line replaceable unit (LRU)

An avionics component designed to be removed and replaced quickly on the aircraft, usually with simple tools, to restore a system without shop-level repair.

Related: Data bus, Built-in test equipment (BITE)
Data bus

A shared set of wires or fiber used to carry digital messages between avionics units, greatly reducing the amount of point-to-point wiring required.

Related: ARINC 429, Line replaceable unit (LRU), Shield termination
American Wire Gauge (AWG)

A standard numbering system that specifies conductor size. Smaller numbers indicate larger wires; each three-number change roughly doubles the cross-sectional area.

Related: Crimp terminal, Splice
Crimp terminal

A terminal or splice attached to a wire by mechanically compressing its barrel around the conductor with a controlled tool, forming a gas-tight electrical and mechanical joint.

Related: American Wire Gauge (AWG), Connector contact
Coaxial cable

A cable with a center conductor surrounded by insulation, a braided shield, and an outer jacket. It carries high-frequency signals with controlled impedance and low loss.

Related: Impedance, Shield termination
Bonding jumper

A low-resistance conductor connecting metal parts so they are electrically common, providing a return path and reducing static buildup, lightning damage, and radio noise.

Related: Electrical ground (return path), Antenna
Shield termination

The method of connecting a cable shield to ground or to a connector shell. Proper termination controls where interference currents flow and preserves shielding effectiveness.

Related: Coaxial cable, Electromagnetic interference (EMI)
Splice

A permanent joint connecting two or more wire ends so they conduct as one conductor. Aviation splices must be mechanically sound, insulated, and approved for the wire type.

Related: Crimp terminal, American Wire Gauge (AWG)
Connector contact

The individual pin or socket inside a connector that mates with its opposite to carry a signal or power. Contacts are crimped or soldered to wires and held in the shell.

Related: Crimp terminal, Splice
Multimeter

A test instrument that measures voltage, resistance, and current, and often continuity. It is the basic tool for verifying aircraft circuits before and after repair.

Related: Continuity test, Voltage drop test
Megohmmeter

An instrument that applies a high test voltage to measure insulation resistance. It detects moisture, contamination, and cracked insulation that an ordinary ohmmeter cannot reveal.

Related: Multimeter, Continuity test
Time-domain reflectometer (TDR)

A test instrument that sends a pulse down a cable and displays reflections. The delay and shape of reflections reveal opens, shorts, and impedance changes along the line.

Related: Coaxial cable, Continuity test
Continuity test

A check, usually made with an ohmmeter, confirming that a conductor provides a complete low-resistance path between two points.

Related: Multimeter, Voltage drop test
Voltage drop test

A measurement of the voltage lost across a connection or conductor while current flows. Excessive drop indicates high resistance such as corrosion or a loose terminal.

Related: Multimeter, Continuity test, Ohm's law
Oscilloscope

An instrument that graphs voltage against time, letting a technician see waveform shape, amplitude, frequency, and noise in a circuit.

Related: Multimeter, Electromagnetic interference (EMI)
Built-in test equipment (BITE)

Diagnostic circuitry built into an avionics unit or system that monitors operation, detects faults, and reports results to the flight crew or maintenance personnel.

Related: Line replaceable unit (LRU), Multimeter
Antenna

A device that radiates or receives electromagnetic energy, converting between guided electrical signals and free-space radio waves. Its performance depends on location, ground plane, and bonding.

Related: Coaxial cable, Bonding jumper, Static discharger
Static discharger

A small pointed device on trailing edges of flight controls that bleeds off accumulated static electricity, reducing precipitation static interference with radios.

Related: Antenna, Electromagnetic interference (EMI)
Electromagnetic interference (EMI)

Unwanted electrical energy, radiated or conducted, that disturbs the operation of electronic equipment. Shielding, grounding, and wire separation are common defenses.

Related: Shield termination, Wire separation, High-intensity radiated fields (HIRF)
High-intensity radiated fields (HIRF)

Strong external radio-frequency fields, such as from radar or broadcast transmitters, that can upset or damage aircraft electronics. Installations must be designed to withstand them.

Related: Electromagnetic interference (EMI), Shield termination
Transponder

An avionics unit that replies to ground radar interrogations with a coded altitude and identity, allowing air traffic control to identify and track the aircraft.

Related: Antenna, Line replaceable unit (LRU)
Wire separation

The practice of physically separating power, signal, and antenna cables to limit coupling of noise and to prevent a single failure from damaging unrelated circuits.

Related: Electromagnetic interference (EMI), Shield termination

NCATT AET study plan

8 weeks · About 7 hours per week

Week 1

Aircraft Fundamentals

  • Sketch and label the primary structural components of a fixed-wing airframe (fuselage, wing, empennage, landing gear) from memory.

  • Differentiate between the four forces of flight and explain how control surfaces (aileron, elevator, rudder, flap) modify them.

  • Identify the major aircraft systems (hydraulic, pneumatic, fuel, electrical, pitot-static) and state the function of each in one sentence.

  • Define standard aviation terminology and abbreviations encountered in maintenance documentation.

Your checkpoint

A hand-drawn or digital airframe/systems diagram with 25+ correctly labeled components, self-graded to 100% accuracy.

Week 2

Basic Electricity and Electronics

  • Apply Ohm's law and the power law to solve 20 numeric circuit problems without a reference sheet.

  • Compute series, parallel, and series-parallel equivalent resistance for mixed circuits.

  • Explain the behavior of inductors and capacitors in DC and AC circuits, including reactance and phase relationships.

  • Differentiate AC and DC generation, rectification, and transformer action in aircraft power systems.

  • Identify schematic symbols for resistors, capacitors, inductors, diodes, transistors, and switches.

Your checkpoint

A worked problem set of 30 circuit calculations with a verified answer key and a one-page symbol reference sheet.

Week 3

Digital Techniques and Aircraft Computers

  • Convert between binary, octal, decimal, and hexadecimal values and perform binary addition/subtraction.

  • Explain the function of logic gates (AND, OR, NOT, NAND, NOR, XOR) and complete truth tables for each.

  • Describe how a microprocessor-based aircraft computer executes instructions (bus, memory, I/O, clock).

  • Differentiate digital data buses used in aircraft (ARINC 429, ARINC 629, MIL-STD-1553, Ethernet) by topology and data rate.

  • Explain the purpose of built-in test equipment (BITE) and how fault codes are generated and retrieved.

Your checkpoint

A two-page digital-techniques reference card covering number conversions, gate truth tables, and bus comparisons, plus a 15-question self-quiz scored at 80% or higher.

Week 4

Wiring, Connectors, and Terminations

  • Identify wire types, gauge sizes, and insulation ratings used in aircraft and select the correct replacement for a given application.

  • Demonstrate the steps for a properly crimped terminal and a soldered splice, listing the inspection criteria for each.

  • Differentiate connector families (circular, rectangular, rack-and-panel) and describe contact insertion/removal tooling.

  • Explain shielding, grounding, bonding, and drip-loop practices and why each matters for EMI and moisture control.

  • Read and interpret a wiring diagram and a wire identification code to trace a circuit end to end.

Your checkpoint

A trace of one complete circuit from a provided (self-authored) wiring description, with every wire labeled by gauge, color code, and termination type.

Week 5

Test Equipment, Measurement, and Troubleshooting

  • Select the correct meter (DMM, megohmmeter, oscilloscope, bond tester) for a stated measurement task and justify the choice.

  • Measure voltage, current, resistance, and continuity on a practice circuit and interpret the readings against expected values.

  • Apply a systematic six-step troubleshooting method to isolate a fault in a described circuit.

  • Explain safety precautions for live-circuit measurement, high voltage, and electrostatic discharge.

Your checkpoint

A written troubleshooting log for three described fault scenarios, each with a fault-isolation path and a final diagnosis matching the answer key.

Week 6

Avionics and Aircraft Systems Installation

  • Describe the installation requirements (power, grounding, bonding, cooling, clearance) for a typical avionics line-replaceable unit.

  • Explain the purpose and routing constraints of coaxial cable, waveguide, and antenna feedlines.

  • Identify the documentation used to support an installation: wire lists, system schematics, STC/installation instructions, and weight-and-balance records.

  • Explain how an installation affects aircraft weight and balance and electromagnetic compatibility.

Your checkpoint

A one-page installation checklist for a hypothetical radio installation covering power, bonding, cooling, routing, and documentation sign-off.

Week 7

Basic Electricity and Electronics & Test Equipment, Measurement, and Troubleshooting

  • Re-solve every missed question from weeks 2 and 5 and write a one-sentence explanation of the correct concept for each.

  • Combine electrical theory with measurement practice by diagnosing three circuits that mix power, ground, and connector faults.

  • Recite key formulas and unit conversions from memory under a 10-minute timed drill.

Your checkpoint

An error log covering at least 20 previously missed items, each closed out with a corrected explanation and a re-test score of 90% or higher.

Week 8

Aircraft Fundamentals & Digital Techniques and Aircraft Computers & Wiring, Connectors, and Terminations & Avionics and Aircraft Systems Installation

  • Complete two full-length timed practice exams and record a per-domain score breakdown.

  • Rebuild the week 1 airframe/system diagram from blank paper in under 15 minutes.

  • Re-derive the digital and wiring reference cards without notes to confirm retention.

  • Rank all six domains by score and schedule targeted review for the two weakest.

Your checkpoint

A final readiness report showing per-domain practice scores, a ranked weak-area list, and a written remediation plan for the two lowest domains.

Milestones

Week 2: Score 80% or higher on a 25-question mixed quiz covering Aircraft Fundamentals and Basic Electricity/Electronics.

Week 4: Complete all four 17%-weight domains (1-4) at least once, with a combined practice score of 80% or higher and no domain below 70%.

Week 6: All six domains covered; per-domain practice scores logged with nothing below 70%.

Week 8: Two full-length timed practice exams completed with an overall score of 85% or higher and no single domain below 80%.

NCATT AET exam day

Your checklist

Government-issued photo ID

Bring an unexpired government-issued photo ID (driver's license, passport, or military ID) with a name that exactly matches your registration. Confirm with the provider which ID forms are accepted and whether a secondary ID is required.

Appointment confirmation / registration receipt

Print or save the confirmation showing your test center, date, time, and candidate/eligibility number. Some centers ask to see it at check-in; confirm with the provider.

Eligibility/experience documentation (if required)

If your certification pathway requires documented training or work experience, confirm with the provider whether it must be submitted before test day or brought in person. Do not assume it can be submitted at the desk.

Read the candidate handbook before test day

The provider's candidate handbook is the authoritative source for ID rules, allowed items, scoring, and rescheduling. Read it rather than relying on secondhand advice.

Confirm test center location, parking, and arrival time

Do a route check the day before and note where to park and which entrance to use. Arrive at least 15-30 minutes early to complete check-in; confirm the provider's late-arrival cutoff.

Confirm the calculator and reference-material policy

Many computer-based certification exams provide on-screen calculators and reference data, and some prohibit personal calculators. Confirm with the provider before assuming either way.

Leave phones, smartwatches, notes, and study materials at home or in the car

Personal items are typically stored in a locker or left outside the testing room. Assume anything not explicitly allowed is prohibited.

Eyeglasses, medications, and other personal necessities

Bring what you need to read a screen comfortably for the full session. Ask the provider in advance about any medical or dietary items you may need to bring into the testing room.

Know your testing accommodations status

Accommodations generally must be requested and approved before test day. If you need extra time or a separate room, confirm with the provider well in advance.

A light snack and water for after the exam

Keep them outside the testing room. Confirm with the provider whether food or drink is permitted during breaks.

A plan for the results

Know in advance how results are reported (typically on-screen at completion and/or by email) and what to do if you do not pass, including any retake waiting period. Confirm with the provider.

Plan the day

72 hours before

Re-read the candidate handbook sections on ID, allowed items, scoring, and rescheduling. Verify your appointment date, time, and test center address, and confirm your ID is unexpired and matches your registered name.

72 hours before

Stop learning new material. Return only to topics you have already studied and got wrong on practice sets, focusing on AET knowledge domains: basic electricity and electronics, aircraft fundamentals, and maintenance/regulatory concepts.

72 hours before

Resolve any open logistics: parking, transportation, time off work, childcare, and accommodations approvals.

24 hours before

Do one short, calm review pass (30-45 minutes) over formulas, units, and vocabulary. Then stop. Cramming the night before reliably costs more in fatigue than it gains in recall.

24 hours before

Pack your ID, confirmation, glasses, and any provider-approved items in one place by the door. Lay out clothing. Set two alarms.

24 hours before

Confirm the test center's phone number and hours in case of a last-minute issue. Get a full night's sleep; sleep is the cheapest score improvement available.

Morning of

Eat a normal meal and hydrate normally. Avoid heavy caffeine if you are not a regular user.

Morning of

Arrive 15-30 minutes before your appointment. Allow extra margin for traffic, security screening, and check-in paperwork.

Morning of

At check-in, present your ID, store all personal items as instructed, and follow the proctor's directions exactly. Ask the proctor any procedural questions before the clock starts.

During the test

Read the tutorial and any on-screen instructions, then do a quick scan of the number of questions and the time limit so you can pace yourself.

During the test

Answer in two passes: work through questions you know confidently first, flag anything that needs more thought, then return to flagged items. Never leave a question blank if the exam does not penalize guessing; confirm the guessing policy with the provider.

During the test

Take any allowed breaks when you notice your focus dropping. Stretch, hydrate, and return with your remaining time budget in mind.

During the test

In the last few minutes, verify you have answered every question, then submit. Note your result as reported and keep any confirmation number or receipt.

Rules to check

  • Bring a valid, unexpired government-issued photo ID whose name matches your registration exactly. If your name has changed or your registration has a typo, contact the provider before test day, not at the desk.

  • Assume that phones, smartwatches, notes, and study materials are prohibited in the testing room. Store them as directed; even possessing a device during the exam can result in score cancellation.

  • Do not disclose, reproduce, or discuss exam content afterward. Certification exams are typically covered by a confidentiality agreement you accept at check-in; confirm the exact terms with the provider.

  • Break policy varies by provider and test center. Ask before the exam starts whether unscheduled breaks are allowed and whether the clock stops during them; confirm with the provider rather than assuming.

  • Scoring and the passing standard are set by the provider, and results are generally reported as pass/fail rather than a raw score. Confirm the passing standard, score reporting method, and retake policy with the provider.

  • Arrive early and know the late-arrival cutoff. Candidates who arrive after the cutoff are typically refused entry and may forfeit the fee; confirm this with the provider.

  • Follow all proctor instructions and test center rules. Suspected misconduct or prohibited-item violations can lead to voided results and loss of eligibility, with appeal handled through the provider's process.

  • If you require accommodations, request and confirm them well before test day. Accommodations are generally not granted on the spot; confirm the provider's deadline.

NCATT AET FAQ

How many NCATT AET practice questions are available?

The practice set has 199 NCATT AET questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many NCATT AET flashcards are available?

The flashcard set has 32 NCATT AET cards. Each card shows the term and its definition.

Which topics does the NCATT AET study material cover?

The NCATT AET study material has 6 sections, including Aircraft Fundamentals, Basic Electricity and Electronics, and Digital Techniques and Aircraft Computers.

What format facts does the catalog list for the NCATT AET exam?

The catalog lists these item types: multiple choice for the NCATT AET exam.