NATE HVAC Practice Test

NATE HVAC Technician Certification

NATE HVAC overview

  • 200 practice questions
  • 32 flashcards
  • 10 study guide topics
  • 34 key terms

What you'll study

  • Core (safety, tools, basic refrigeration and electrical fundamentals)10%
  • Air Conditioning10%
  • Air Distribution10%
  • Gas Heating10%
  • Heat Pump10%
  • Oil Heating10%
  • Hydronics (Gas and Oil)10%
  • Light Commercial Air Conditioning10%
  • Commercial Refrigeration10%
  • Light Commercial Refrigeration10%

NATE certification is a professional credential for heating, ventilation, air conditioning and refrigeration (HVACR) technicians. NATE describes itself as the nation's largest nonprofit certification organization for HVACR technicians, and its credentials are used by contractors who want a verifiable, third-party signal of a technician's competence rather than a self-reported resume line. The program serves working service and installation technicians as well as aspiring techs moving from training into field work.

Exams are multiple choice and organized by specialty, so a technician generally pairs a core credential with one or more focus areas such as air conditioning, air distribution, gas heating, heat pumps, oil heating, hydronics, light commercial air conditioning, commercial refrigeration, or light commercial refrigeration. Core material - safety, tools, and basic refrigeration and electrical fundamentals - underlies every specialty exam, so weakness there costs points across the board.

Preparation should be deliberate rather than general. NATE publishes exam KATEs (knowledge areas of technician expertise) that describe what each exam measures; treat them as a checklist and study only to the listed depth. Pair that with hands-on review of the equipment you actually service, NATE's "How to Prepare" guidance, recognized training providers, and the NATE Training Academy. Candidates can test at a testing organization or through live online proctoring.

Common mistakes

Jumping out a pressure switch, high-limit, or flame rollout switch to 'see if the unit runs' while troubleshooting instead of proving the safety circuit with a meter.

It is faster in the field to bypass a suspected switch than to ohm it out, and technicians carry jumpers out of habit; the exam tests safety sequence, not shortcut speed.

What to do instead

Never bypass a safety to diagnose. De-energize, isolate the circuit, and check each switch for continuity at its actual operating condition, then verify the upstream condition (draft, pressure, temperature) that made the switch open. State the sequence of safeties in order before touching a jumper.

Taking resistance readings on a live circuit, failing to zero or subtract lead resistance, or using a high-impedance meter to check for a 'real' voltage on a control circuit.

Candidates mix up when to use volts vs. ohms vs. amps under time pressure, and ghost voltage from induced EMF makes a dead circuit look live or vice versa.

What to do instead

Fix a habit order: volts first (with the meter in parallel, Lo-Z if available), amps with the meter in series or a clamp, ohms only with power off and the component isolated. Short the leads together and record the lead resistance before measuring small resistances like motor windings or thermistors.

Charging or condemning a system based on gauge pressures alone, without measuring indoor wet-bulb and outdoor dry-bulb, and without identifying whether the metering device is a fixed orifice or a TXV.

Pressures look 'low' or 'high' but are meaningless without the load conditions; candidates also apply a superheat target to a TXV system or a subcooling target to a piston system.

What to do instead

Identify the metering device first. For a fixed orifice/piston, measure indoor WB and outdoor DB, look up the target superheat for those conditions, and charge to superheat. For a TXV, charge to the subcooling value on the rating plate. Record all four temperatures with the readings.

Diagnosing low suction pressure or a poor temperature split as low refrigerant charge before checking filter, evaporator coil condition, blower wheel, belt, and duct restrictions.

Low charge is the 'expected' answer, and airflow problems produce the same low suction/high superheat signature; candidates skip the airflow check because it takes longer.

What to do instead

Every no-cool/poor-cool call gets airflow verified first: measure the return/supply temperature split, inspect the filter, look at the coil face and blower wheel, and take static pressure. Only after airflow is proven adequate do you evaluate charge with superheat or subcooling.

Measuring external static pressure at only one point, using the wrong tap, or comparing a wet-coil reading to the dry-coil blower table.

Candidates assume one static reading tells the whole story; they forget supply static and return static are both negative/positive magnitudes that must be added, and that a wet coil adds resistance the table may or may not include.

What to do instead

Measure return static in the return plenum and supply static in the supply plenum, take the absolute value of each, and add them for total external static. Compare against the manufacturer's blower table for the actual coil condition (wet vs. dry) and the actual speed tap, then convert to CFM and verify against required airflow.

Setting manifold pressure or 'clocking the meter' on a gas furnace with the burner compartment open, before steady-state operation, or without correcting the gas meter reading for the local heating value.

Field practice often checks gas pressure right after light-off; the exam expects a stabilized condition and a calculated input rather than a glance at a gauge.

What to do instead

Let the appliance reach steady state with the burner door installed, then read manifold pressure with a water-column manometer at the manifold port and compare to the rating plate. Clock the meter over a full revolution: input BTU/hr = (ft³ per revolution × 3600 ÷ seconds per revolution) × heating value of the gas, then compare to rated input.

Condemning the defrost control board on a heat pump when the complaint is a failed defrost sensor, ambient thermostat, or reversing valve, and comparing heating-mode suction pressure to cooling-mode expectations.

In heating, the outdoor coil is the evaporator and the pressures and the 'suction' port location differ; candidates carry over cooling-mode logic and misread a normal heating-mode pressure as a fault.

What to do instead

Confirm the mode first, then read pressures at the true suction port (between the reversing valve and the compressor) rather than the common suction port. Test the defrost sensor/thermostat by resistance against its temperature chart, force a defrost cycle to observe the sequence, and check reversing valve operation by the temperature difference across the valve body.

Setting nozzle electrode gap, electrode length, and Z-dimension from memory or 'by eye', or installing whatever nozzle angle is on the truck rather than the one the chamber was designed for.

Oil settings are equipment-specific and vary by manufacturer; candidates assume one standard and skip the spec sheet, and a wrong spray angle or electrode position changes ignition reliability and flame shape.

What to do instead

Use the manufacturer's nozzle/electrode setting gauge or the appliance spec sheet for that model; match nozzle GPH, spray angle, and pattern to the combustion chamber, set the Z-dimension and electrode gap to spec, then confirm with a smoke test, CO₂, and draft reading after the burner stabilizes.

Leaving air in a hydronic loop, installing a circulator with the flange or flow arrow wrong, or judging flow by 'feels hot' rather than by temperature differential.

Air-bound loops mimic a failed pump silently, and the pump body/flange orientation rules (shaft horizontal, flow arrow, pumping away from the expansion tank) are easy to overlook on a retrofit.

What to do instead

Purge each zone at the purge station with the system isolated until no air is heard or seen, verify the circulator flow arrow and that the shaft is horizontal, then prove flow with a supply/return temperature differential across the boiler or at each zone and compare to the design delta-T. Check the pump curve against head before replacing a pump.

Confusing case temperature differential with evaporator superheat, or calling low suction pressure a low charge on a commercial case without checking for a restricted/iced coil, a failed EEV, or a stuck case controller.

Commercial refrigeration is read with two different numbers (product TD and superheat at the evaporator outlet), and candidates carry over residential 'low suction = low charge' logic.

What to do instead

Stabilize the case first (doors closed, product at temperature, defrost terminated), then take superheat at the evaporator outlet and compare to the case design value, separately take the case-to-product TD, and check subcooling at the condenser. Investigate the metering device and coil condition before adding refrigerant.

Exam requirements can change. Confirm current details with the exam provider.

NATE HVAC practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Core (safety, tools, basic refrigeration and electrical fundamentals)

    When connecting gauges to a residential split system to handle liquid refrigerant, which personal protective equipment is required?

    1. Insulating gloves and splash goggles Correct answer.
    2. Safety glasses only
    3. Cotton work gloves
    4. Ear plugs and a dust mask

    Explanation

    Liquid refrigerant at atmospheric pressure boils far below freezing, so a splash or a wetted glove causes instant frostbite. Insulating gloves and splash goggles protect the hands and eyes from liquid spray and from a burst of cold vapor.

  2. Question 2Core (safety, tools, basic refrigeration and electrical fundamentals)

    On a standard three-hose manifold gauge set, which color identifies the low-side gauge and hose?

    1. Green
    2. Red
    3. Blue Correct answer.
    4. Yellow

    Explanation

    Manifold sets follow a standard color code so a technician can connect quickly without crossing the high and low sides. Blue is the low-side (suction) gauge and hose, red is the high-side (discharge) gauge and hose, and yellow is the center hose used for charging or evacuation.

  3. Question 3Core (safety, tools, basic refrigeration and electrical fundamentals)

    Electrical resistance is measured in which unit?

    1. Watts
    2. Volts
    3. Ohms Correct answer.
    4. Amperes

    Explanation

    Resistance opposes current flow and is expressed in ohms, symbolized by the Greek letter omega. Volts describe electrical potential difference, amperes describe current flow, and watts describe power.

  4. Question 4Core (safety, tools, basic refrigeration and electrical fundamentals)

    In a vapor-compression refrigeration system, which component absorbs heat from the air being cooled?

    1. Evaporator Correct answer.
    2. Metering device
    3. Compressor
    4. Condenser

    Explanation

    The evaporator is the indoor coil where low-pressure refrigerant boils and absorbs heat from the airstream passing over it. The condenser rejects that heat outdoors, the compressor raises the vapor pressure and temperature, and the metering device controls refrigerant flow into the evaporator.

  5. Question 5Core (safety, tools, basic refrigeration and electrical fundamentals)

    Before opening the electrical compartment of an energized rooftop unit, a technician should first:

    1. Remove the blower panel and the filter
    2. Discharge the run capacitor and start the unit
    3. Lock out the disconnect and verify with a meter Correct answer.
    4. Turn the thermostat to fan-on and wait

    Explanation

    Lockout/tagout isolates the equipment from its power source and prevents another person from energizing it while work is in progress. The circuit must then be verified de-energized with a meter, because a disconnect or breaker label alone does not prove the line is dead.

  6. Question 6Core (safety, tools, basic refrigeration and electrical fundamentals)

    Which instrument is used to measure the vacuum level in a system during evacuation?

    1. Electronic micron gauge Correct answer.
    2. Manifold gauge set
    3. Sling psychrometer
    4. Anemometer

    Explanation

    A micron gauge reads deep vacuum directly at the system, in microns of mercury, and can resolve levels far below what a manifold gauge can show. Its resolution is what allows a technician to confirm that evacuation has removed moisture-laden air.

  7. Question 7Core (safety, tools, basic refrigeration and electrical fundamentals)

    A 24-volt control circuit has a total resistance of 8 ohms. What current flows through the circuit?

    1. 12 A
    2. 0.33 A
    3. 3 A Correct answer.
    4. 192 A

    Explanation

    Ohm's law states that current equals voltage divided by resistance. Dividing 24 volts by 8 ohms gives 3 amperes.

  8. Question 8Core (safety, tools, basic refrigeration and electrical fundamentals)

    R-410A is a zeotropic blend. To keep the composition correct, refrigerant should be removed from the cylinder:

    1. as a vapor
    2. as a vapor after warming the cylinder
    3. as a liquid Correct answer.
    4. in either state, because the composition does not change

    Explanation

    In a zeotropic blend the components have different boiling points, so drawing vapor off the top removes the more volatile component first and leaves the remaining charge with a different composition. Charging as a liquid keeps the blended ratio intact.

  9. Question 9Core (safety, tools, basic refrigeration and electrical fundamentals)

    What is the maximum liquid fill level for a refrigerant recovery cylinder?

    1. 95 percent
    2. 50 percent
    3. 80 percent Correct answer.
    4. 100 percent

    Explanation

    Recovery cylinders must be filled to no more than 80 percent of their capacity by liquid volume so that liquid expansion with rising temperature leaves vapor space. Filling beyond that can result in a hydrostatic condition and relief valve discharge.

  10. Question 10Core (safety, tools, basic refrigeration and electrical fundamentals)

    What is the correct way to prepare a run capacitor before removing it from a circuit?

    1. Discharge it through a bleeder resistor, then verify Correct answer.
    2. Replace it whenever the cabinet is opened
    3. Test it with an ohmmeter while the unit is energized
    4. Assume it is empty once the disconnect is open

    Explanation

    A capacitor can store a dangerous charge after the power is removed, so its terminals must be bled down through a resistor rated for the job. Verifying with a meter confirms the stored voltage is gone before the terminals are touched.

  11. Question 11Core (safety, tools, basic refrigeration and electrical fundamentals)

    Which gas is used for pressure testing a refrigeration system?

    1. Acetylene
    2. Dry nitrogen Correct answer.
    3. Compressed air
    4. Oxygen

    Explanation

    Dry nitrogen is inert and does not introduce moisture, oxygen, or fuel into the system, and it is supplied through a pressure regulator to a safe test pressure. Oxygen and compressed air can combine with refrigerant oil under pressure and create a fire or explosion hazard.

  12. Question 12Core (safety, tools, basic refrigeration and electrical fundamentals)

    Subcooling is defined as:

    1. suction line temperature minus evaporating saturation temperature
    2. temperature rise measured across the condenser coil
    3. liquid line temperature minus condensing saturation temperature Correct answer.
    4. pressure drop measured across the metering device

    Explanation

    Subcooling measures how far the liquid leaving the condenser has been cooled below its condensing saturation temperature. It is a check of how much liquid is stacked in the condenser and is used to verify charge on a fixed-orifice system.

  13. Question 13Core (safety, tools, basic refrigeration and electrical fundamentals)

    In a 24-volt control circuit, which component closes the line-voltage contacts that power the compressor?

    1. Contactor Correct answer.
    2. Thermostat
    3. Transformer
    4. Capacitor

    Explanation

    The contactor coil is energized by the low-voltage control circuit, and its magnetic pull closes the heavy line-voltage contacts feeding the compressor. The thermostat only switches the low-voltage signal that energizes the coil.

  14. Question 14Core (safety, tools, basic refrigeration and electrical fundamentals)

    Evaporator outlet superheat measures 2°F on a system with a piston metering device. This indicates:

    1. An overcharged system with excess liquid in the condenser
    2. Liquid refrigerant flooding the evaporator coil Correct answer.
    3. Normal operation at design conditions
    4. A restricted liquid line or clogged filter-drier

    Explanation

    Superheat is the margin above saturation at the evaporator outlet, so a very low value means the refrigerant has not fully boiled off before leaving the coil. That condition can return liquid to the compressor and cause slugging and oil dilution.

  15. Question 15Core (safety, tools, basic refrigeration and electrical fundamentals)

    Under ASHRAE Standard 34, which of these refrigerants carries the A1 safety classification?

    1. R-717 (ammonia)
    2. R-410A Correct answer.
    3. R-290 (propane)
    4. R-32

    Explanation

    The A1 classification means low toxicity in Group A and no flame propagation in Group 1 according to ASHRAE 34 testing. R-410A is rated A1, while propane, ammonia, and R-32 fall into more hazardous classes.

  16. Question 16Core (safety, tools, basic refrigeration and electrical fundamentals)

    A voltmeter placed across a switch in an energized circuit reads 0 volts. This means:

    1. The switch has developed high contact resistance
    2. The switch contacts are open and the circuit is broken
    3. The switch is closed with negligible voltage drop Correct answer.
    4. The circuit is de-energized at the panel

    Explanation

    Voltage is a difference in potential, so a good closed switch has nearly the same potential on both terminals and shows almost no drop. A reading of full circuit voltage across the switch is what indicates open contacts.

  17. Question 17Core (safety, tools, basic refrigeration and electrical fundamentals)

    A cylinder of R-134a reads 71 psig at 70°F. A second cylinder of the same refrigerant at 70°F that contains only half as much liquid will read:

    1. a higher pressure because of the larger vapor space
    2. about 35 psig
    3. the same 71 psig Correct answer.
    4. zero until the cylinder is inverted

    Explanation

    As long as liquid and vapor are both present, a refrigerant's pressure is its saturation pressure at that temperature and depends only on temperature. The amount of liquid in the cylinder does not change the pressure until the liquid is completely gone.

  18. Question 18Core (safety, tools, basic refrigeration and electrical fundamentals)

    A single-phase compressor shows 1.2 ohms from common to run, 2.0 ohms from common to start, and 3.2 ohms from run to start. These readings indicate:

    1. Normal windings Correct answer.
    2. A shorted run winding
    3. An open start winding
    4. A winding grounded to the shell

    Explanation

    The run and start windings are joined at the common terminal, so the resistance measured run-to-start should equal the sum of the two individual windings. Here 1.2 plus 2.0 equals 3.2 ohms, which matches the measured value and confirms the windings are intact.

  19. Question 19Core (safety, tools, basic refrigeration and electrical fundamentals)

    A system has low suction pressure, high evaporator superheat, and a clear sight glass. Which condition best explains these readings?

    1. A restricted liquid line filter-drier Correct answer.
    2. A metering device that is overfeeding
    3. A dirty condenser coil
    4. An overcharge of refrigerant

    Explanation

    A restriction in the liquid line limits how much refrigerant reaches the evaporator, so the coil is starved and superheat rises while suction pressure falls. Because the restriction is downstream of the receiver, the sight glass can still show a clear liquid stream.

  20. Question 20Core (safety, tools, basic refrigeration and electrical fundamentals)

    Line-to-line voltage readings on a three-phase unit are 240 V, 236 V, and 244 V. How should the technician evaluate this supply?

    1. Unacceptable, because the imbalance exceeds 2%
    2. Acceptable, but only if the current readings are also balanced
    3. Acceptable, because the imbalance is under 2% Correct answer.
    4. Unacceptable, because the imbalance exceeds 5%

    Explanation

    Voltage imbalance is found by taking the greatest deviation from the average and dividing it by the average. The average here is 240 V with a maximum deviation of 4 V, giving about 1.7 percent, which is within the commonly applied 2 percent limit for motor-powered equipment.

  21. Question 21Air Conditioning

    Superheat is best described as:

    1. the temperature drop of the air as it passes across the evaporator coil
    2. the difference between the liquid line temperature and the saturation temperature at discharge pressure
    3. the difference between the actual suction line temperature and the saturation temperature at suction pressure Correct answer.
    4. the temperature difference between the entering and leaving condenser air

    Explanation

    Superheat is the amount by which the refrigerant vapor is above its saturation temperature at the measured suction pressure. It is found by subtracting the saturation temperature for the suction pressure from the actual suction line temperature. It confirms that no liquid refrigerant is returning to the compressor.

  22. Question 22Air Conditioning

    In a properly operating direct-expansion system, the refrigerant entering the evaporator is:

    1. a superheated low-pressure vapor
    2. a low-pressure liquid and vapor mixture Correct answer.
    3. a high-pressure subcooled liquid
    4. a high-pressure superheated vapor

    Explanation

    The metering device drops pressure and flashes part of the refrigerant before it enters the distributor and coil. This two-phase mixture boils at a low saturation temperature and absorbs heat from the air. By the evaporator outlet, all liquid should be boiled off and a small amount of superheat added.

  23. Question 23Air Conditioning

    The primary function of the condenser in a split air conditioning system is to:

    1. reduce the refrigerant pressure before the evaporator
    2. meter the flow of refrigerant into the evaporator
    3. absorb heat from the conditioned space
    4. reject heat from the refrigerant and condense it to a liquid Correct answer.

    Explanation

    The condenser removes sensible heat from the discharge vapor until it reaches saturation, then removes latent heat to condense it into a liquid. This heat is rejected to the outdoor air moving across the coil. A small additional amount of sensible heat is removed as the liquid is subcooled.

  24. Question 24Air Conditioning

    Wet-bulb temperature is best described as:

    1. the saturation temperature of the refrigerant at suction pressure
    2. the temperature of the air measured with a dry-bulb thermometer
    3. the temperature at which water condenses inside the ductwork
    4. the lowest temperature that air can reach by evaporative cooling Correct answer.

    Explanation

    A wet-bulb thermometer has a moistened wick, and evaporation cools the bulb below the dry-bulb reading. The wet-bulb temperature therefore reflects the moisture content of the air and represents the limit of evaporative cooling. The difference between dry-bulb and wet-bulb is the wet-bulb depression.

  25. Question 25Air Conditioning

    The thermostatic expansion valve controls:

    1. refrigerant flow into the evaporator to maintain a set superheat Correct answer.
    2. refrigerant flow into the condenser to maintain head pressure
    3. the compressor discharge pressure during low ambient conditions
    4. the volume of air moving across the evaporator coil

    Explanation

    The TXV modulates a needle and seat to hold a target superheat at the evaporator outlet. It responds to the bulb pressure at the outlet, the evaporator pressure below the diaphragm, and the spring setting. Because it regulates superheat, charging on these systems is normally done by subcooling.

  26. Question 26Air Conditioning

    A heavily fouled evaporator coil most directly causes:

    1. higher than normal subcooling with normal head pressure
    2. reduced airflow and a lower suction pressure Correct answer.
    3. higher head pressure with a normal suction pressure
    4. higher than normal superheat with unchanged airflow

    Explanation

    A dirty coil blocks airflow and reduces heat transfer, so less heat reaches the refrigerant and the suction pressure drops. Because less of the coil is actively boiling refrigerant, the superheat reading is often unsteady or low. Cleaning the coil and verifying airflow is the correction.

  27. Question 27Air Conditioning

    A system shows a suction pressure of 60 psig and a suction line temperature of 62°F. The saturation temperature at 60 psig is approximately 34°F. The measured superheat is:

    1. 96°F of superheat
    2. 28°F of superheat Correct answer.
    3. 2°F of superheat
    4. 28°F of subcooling

    Explanation

    Superheat equals the suction line temperature minus the saturation temperature for the suction pressure. Subtracting 34°F from 62°F gives 28°F, which is well above the typical target and suggests the coil is being starved of refrigerant. A common cause is undercharge or a restriction in the metering device or liquid line.

  28. Question 28Air Conditioning

    On a TXV system, subcooling measured at the condenser outlet is 2°F while the manufacturer specifies 10°F. The most likely cause is:

    1. an undercharge of refrigerant Correct answer.
    2. excessive condenser airflow
    3. an overcharge of refrigerant
    4. a restricted suction line

    Explanation

    Subcooling indicates how much liquid refrigerant is stacked in the bottom of the condenser, so low subcooling means not enough liquid is being backed up. That points to an undercharge or to the TXV feeding more refrigerant than the system holds. Charge is added only after confirming airflow and that no leaks exist.

  29. Question 29Air Conditioning

    Compared with R-22, R-410A systems require:

    1. POE oil and gauges rated for higher pressures Correct answer.
    2. no special attention to oil return in the piping
    3. mineral oil and standard R-22 gauge sets
    4. lower condensing pressures at the same ambient temperature

    Explanation

    R-410A operates at roughly 50 to 60 percent higher pressures than R-22, so manifold gauge sets and hoses must be rated for it. It is also a blend that uses polyolester (POE) oil, which readily absorbs moisture. Recovery equipment and cylinders must likewise be rated for the higher pressure.

  30. Question 30Air Conditioning

    To determine the operating superheat of a system, a technician needs:

    1. condensing temperature and outdoor ambient temperature
    2. suction pressure and entering air wet-bulb temperature
    3. liquid line temperature and discharge pressure
    4. suction line temperature and suction pressure Correct answer.

    Explanation

    Superheat is the suction line temperature minus the saturation temperature corresponding to the suction pressure. Both readings must be taken at the same point on the suction line, near the evaporator outlet. Comparing that value against the manufacturer's target confirms whether the coil is properly fed.

  31. Question 31Air Conditioning

    The difference between the condensing saturation temperature and the outdoor ambient temperature is called the:

    1. condensing split Correct answer.
    2. approach
    3. superheat
    4. evaporator temperature drop

    Explanation

    The condensing split compares the saturation temperature in the condenser with the air entering the coil. A large split suggests the condenser is rejecting heat poorly, often from dirt, recirculated air, or low airflow. A small split with high head pressure may point to a non-condensable or an overcharge.

  32. Question 32Air Conditioning

    Latent heat removal at the evaporator coil:

    1. increases the sensible-to-total ratio of the coil
    2. raises the dry-bulb temperature of the supply air
    3. converts water vapor to liquid without changing air temperature Correct answer.
    4. has no measurable effect on the amount of condensate the coil produces

    Explanation

    Latent heat is the heat removed when water vapor changes to liquid water on the coil, and it occurs without a change in dry-bulb temperature. The liquid drains away as condensate, which lowers the moisture content of the supply air. Sensible heat removal is the separate process that lowers the air's dry-bulb temperature.

  33. Question 33Air Conditioning

    A typical acceptable dry-bulb temperature drop across a properly operating evaporator coil is:

    1. 25°F to 35°F
    2. 16°F to 22°F Correct answer.
    3. 40°F to 50°F
    4. 4°F to 8°F

    Explanation

    Most residential and light commercial coils are designed for roughly a 16°F to 22°F difference between return and supply air under design conditions. The exact target varies with the wet-bulb entering the coil and must be checked against the manufacturer's data. A drop outside this range usually signals an airflow or charge problem.

  34. Question 34Air Conditioning

    An air conditioner satisfies the thermostat quickly on every cycle and then short-cycles, while the refrigerant charge and airflow have been verified as correct. The most likely cause is that the unit:

    1. is oversized for the building load Correct answer.
    2. has a blower set to low speed
    3. has a restricted metering device
    4. has a failed compressor

    Explanation

    An oversized unit removes sensible heat faster than the space gains it, so the thermostat is satisfied before the coil can remove much moisture. The result is short run times, uneven temperatures, and poor humidity control. Correct sizing to the calculated load is the lasting solution.

  35. Question 35Air Conditioning

    Bubbles visible in the liquid line sight glass of a TXV system indicate:

    1. a liquid line restriction or insufficient subcooling Correct answer.
    2. normal operation during high ambient conditions
    3. an excess refrigerant charge
    4. too much airflow across the condenser

    Explanation

    Flash gas appears when liquid refrigerant pressure drops below its saturation pressure or when not enough liquid is available, such as from a restriction or an undercharge. On a TXV system the correct response is to verify subcooling at the condenser outlet and check for a temperature drop across the filter drier. A solid column of liquid is expected at the sight glass under normal conditions.

  36. Question 36Air Conditioning

    A coil removes 36,000 Btu/h of sensible heat with a 20°F temperature drop across it. Using the sensible heat equation, the airflow is approximately:

    1. 3,300 cfm
    2. 800 cfm
    3. 1,200 cfm
    4. 1,670 cfm Correct answer.

    Explanation

    The sensible heat equation is Btu/h = 1.08 × cfm × temperature difference, so cfm equals Btu/h divided by (1.08 × ΔT). Dividing 36,000 by (1.08 × 20), or 21.6, gives about 1,667 cfm. The 1.08 constant applies to standard air at sea level.

  37. Question 37Air Conditioning

    A TXV system shows high superheat with subcooling that matches the manufacturer's target. This most likely means the:

    1. condenser has poor airflow
    2. TXV is overfeeding the evaporator
    3. system is overcharged with refrigerant
    4. TXV is underfeeding the evaporator Correct answer.

    Explanation

    Normal subcooling shows the condenser has the right amount of liquid, so the problem lies on the low side. High superheat with a properly charged system indicates the valve is not admitting enough refrigerant, as with a lost bulb charge, a sticking valve, or a blocked inlet screen. The starved coil will show a low suction pressure and a small temperature drop.

  38. Question 38Air Conditioning

    A coil has a sensible heat ratio of 0.70 and a total capacity of 40,000 Btu/h. The latent capacity is:

    1. 28,000 Btu/h
    2. 12,000 Btu/h Correct answer.
    3. 8,000 Btu/h
    4. 40,000 Btu/h

    Explanation

    The sensible heat ratio is the sensible capacity divided by the total capacity, so the latent share is one minus that ratio. Here 30 percent of 40,000 Btu/h is the latent portion, or 12,000 Btu/h. The remaining 28,000 Btu/h is sensible capacity.

  39. Question 39Air Conditioning

    A fan-cycling or head pressure control on an air-cooled condenser operating in cold weather is used to:

    1. increase superheat at the evaporator outlet
    2. raise the evaporator airflow rate
    3. reduce the running current of the compressor
    4. maintain adequate condensing pressure for proper metering and lubrication Correct answer.

    Explanation

    Low ambient temperatures drop the condensing pressure, which reduces the pressure difference across the metering device and can starve the evaporator. It also lowers the mass flow of refrigerant returning to the compressor for cooling and oil movement. Cycling the fan or modulating its speed keeps head pressure in a workable range.

  40. Question 40Air Conditioning

    A fixed-orifice (piston) system operating at design indoor wet-bulb shows only 3°F of superheat. The most appropriate action is to:

    1. add refrigerant to raise the superheat
    2. recover refrigerant to raise the superheat Correct answer.
    3. install a larger metering piston
    4. increase the condenser airflow

    Explanation

    With a fixed orifice, superheat rises as charge is removed and falls as charge is added. A superheat well below the target indicates the evaporator is flooded, which risks liquid floodback to the compressor, so refrigerant is recovered. Charge is adjusted in small increments while allowing the system to stabilize.

  41. Question 41Air Distribution

    Which supply duct sizing method holds the friction loss per foot of duct constant from the fan to the last outlet?

    1. Equal friction Correct answer.
    2. Constant velocity
    3. Static regain
    4. Velocity reduction

    Explanation

    The equal friction method sizes every section so that the pressure loss per foot of length is the same throughout the supply system. This simplifies layout work and gives a reasonably self-balancing system with a single friction-rate calculation.

  42. Question 42Air Distribution

    A pitot tube reads a velocity pressure of 0.25 in. w.c. in a main supply duct. The air velocity is closest to:

    1. 2500 fpm
    2. 1500 fpm
    3. 1000 fpm
    4. 2000 fpm Correct answer.

    Explanation

    Velocity in fpm equals 4005 times the square root of velocity pressure in inches of water column. The square root of 0.25 is 0.5, and 4005 times 0.5 is about 2000 fpm.

  43. Question 43Air Distribution

    A 12 in. by 12 in. duct carries air at 800 fpm. What is the airflow through the duct?

    1. 533 cfm
    2. 800 cfm Correct answer.
    3. 267 cfm
    4. 400 cfm

    Explanation

    Airflow equals velocity multiplied by cross-sectional area. A 12 in. by 12 in. duct has an area of 144 square inches, exactly 1 square foot, so 800 fpm times 1 square foot equals 800 cfm.

  44. Question 44Air Distribution

    Flexible duct runs should be supported at intervals no greater than:

    1. 4 ft Correct answer.
    2. 10 ft
    3. 8 ft
    4. 6 ft

    Explanation

    Industry and manufacturer installation standards require flexible duct to be supported at approximately 4 ft intervals, with the duct not allowed to sag between supports. Sagging flattens the duct, reduces its effective diameter, and sharply increases pressure loss and airflow reduction.

  45. Question 45Air Distribution

    Which term describes the distance from a supply outlet to the point where the airstream velocity has decayed to a specified terminal value, commonly 50 fpm?

    1. Drop
    2. Entrainment
    3. Spread
    4. Throw Correct answer.

    Explanation

    Throw is the measured distance from the outlet face to the point where the airstream slows to the stated terminal velocity. It is the primary number used to decide outlet spacing and whether conditioned air reaches the occupied zone.

  46. Question 46Air Distribution

    Total pressure at a point inside a duct is equal to:

    1. Velocity pressure alone
    2. Static pressure plus velocity pressure Correct answer.
    3. Static pressure only, measured at the fan outlet
    4. Static pressure minus velocity pressure

    Explanation

    Total pressure is the algebraic sum of static pressure and velocity pressure at the same point. Static pressure acts against the duct walls, while velocity pressure represents the kinetic energy of the moving airstream.

  47. Question 47Air Distribution

    A rectangular duct measures 8 in. by 32 in. What is its aspect ratio?

    1. 8:1
    2. 4:1 Correct answer.
    3. 6:1
    4. 2:1

    Explanation

    Aspect ratio is the duct width divided by its depth, so 32 divided by 8 equals a 4:1 ratio. Ratios wider than about 4:1 increase friction and make the duct harder to fabricate and support.

  48. Question 48Air Distribution

    A blower is rated at 0.50 in. w.c. external static pressure. The filter, coil, and grilles account for 0.15, 0.20, and 0.05 in. w.c. respectively. What static pressure remains available for the duct system?

    1. 0.30 in. w.c.
    2. 0.35 in. w.c.
    3. 0.10 in. w.c. Correct answer.
    4. 0.20 in. w.c.

    Explanation

    Available static pressure equals the blower's rated external static pressure minus the pressure drops of the components that are not part of the duct run. The three components total 0.40 in. w.c., leaving 0.50 minus 0.40, or 0.10 in. w.c.

  49. Question 49Air Distribution

    Where should a volume damper be installed to balance a single branch run off a trunk duct?

    1. In the return air plenum at the air handler
    2. At the branch takeoff near the main trunk Correct answer.
    3. On the fan discharge side of the air handler
    4. At the last outlet on the branch run

    Explanation

    A damper placed in the branch takeoff controls the entire branch and can be locked in position, which is what balancing requires. Locating it at the last outlet leaves the rest of the run unregulated and the branch cannot be trimmed as a unit.

  50. Question 50Air Distribution

    A bedroom with a supply register and a closed door needs a return path. This is normally provided by:

    1. A larger supply diffuser in the room
    2. Opening a window in the adjacent room
    3. A transfer grille or a door undercut Correct answer.
    4. A barometric relief damper in the ceiling

    Explanation

    A closed door can pressurize the room and choke off supply airflow, so a dedicated return path such as a transfer grille, jumper duct, or door undercut must be sized for the return airflow. This keeps the room at neutral pressure and allows the supply air to enter.

  51. Question 51Air Distribution

    Which method gives the most durable airtight seal on the longitudinal seams of galvanized steel duct?

    1. Pressure-sensitive cloth tape pressed onto the seam
    2. Mastic applied over the seam Correct answer.
    3. Spray adhesive applied before assembly
    4. One sheet metal screw at each end of the seam

    Explanation

    Mastic, or mastic-backed tape, bonds to the metal and stays flexible, forming a permanent seal that does not dry out and release the way cloth or plastic tapes do. Mechanical fasteners hold the seam together but do not seal the leak path.

  52. Question 52Air Distribution

    A belt-driven blower is sped up from 900 rpm to 990 rpm while the airflow rises 10 percent. The static pressure rises by approximately:

    1. 19 percent
    2. 33 percent
    3. 21 percent Correct answer.
    4. 10 percent

    Explanation

    Fan laws state that static pressure varies with the square of fan speed. The speed ratio is 1.10, and 1.10 squared is 1.21, which is a 21 percent increase in static pressure.

  53. Question 53Air Distribution

    What is the effect of a return-air filter that has loaded heavily with dust?

    1. No change in airflow or pressure drop
    2. Less airflow and a higher filter pressure drop Correct answer.
    3. More airflow across the evaporator coil
    4. Lower filter pressure drop with unchanged airflow

    Explanation

    A loaded filter adds resistance on the return side, so the blower moves less air and the measured pressure drop across the filter rises. Filters are therefore changed on a pressure-drop or scheduled basis rather than waiting for visible dirt.

  54. Question 54Air Distribution

    To minimize turbulence and pressure loss, a supply duct transition should generally have an included angle no greater than about:

    1. 75 degrees
    2. 90 degrees
    3. 60 degrees
    4. 45 degrees Correct answer.

    Explanation

    Transitions with a total included angle of roughly 45 degrees or less keep the airflow attached to the sloping sides. Steeper transitions cause separation and eddy currents, which add pressure loss and generate noise.

  55. Question 55Air Distribution

    In a VAV system, as the zone boxes throttle toward minimum flow, the static pressure in the supply main will:

    1. Rise Correct answer.
    2. Stay the same
    3. Reverse direction
    4. Fall

    Explanation

    When terminal boxes close, total system airflow drops and the fan operates further up its curve, so the static pressure in the supply main rises. A static pressure sensor, usually located about two thirds of the way down the main, signals the fan to reduce speed or modulate a bypass.

  56. Question 56Air Distribution

    On a cooling duct installed in a hot, humid attic, the vapor retarder should be located:

    1. On the outside of the insulation jacket Correct answer.
    2. Between two layers of insulation
    3. On the bare metal duct before insulation is applied
    4. On the inside, facing the airstream

    Explanation

    The vapor retarder belongs on the warm side of the insulation so moisture-laden attic air cannot reach the cold duct surface. Placing it on the outside of the jacket keeps the insulation dry and prevents condensation and mold growth.

  57. Question 57Air Distribution

    A return air grille has 1.5 square feet of free area and passes 600 cfm. The air velocity through the free area is:

    1. 500 fpm
    2. 900 fpm
    3. 400 fpm Correct answer.
    4. 300 fpm

    Explanation

    Velocity equals airflow divided by the free area of the grille. Dividing 600 cfm by 1.5 square feet gives 400 fpm, which is within the normal range for a return grille.

  58. Question 58Air Distribution

    Which duct design method reduces the duct size after each takeoff so that velocity pressure is converted back into static pressure to offset friction loss?

    1. Velocity reduction method
    2. Equal friction method
    3. Static regain method Correct answer.
    4. Constant velocity method

    Explanation

    The static regain method makes each downstream section smaller so the airstream slows and recovers pressure, holding nearly constant static pressure along the main. It is well suited to high-velocity and extended systems where pressure recovery matters.

  59. Question 59Air Distribution

    If the air velocity in a duct doubles while the air density stays the same, the velocity pressure becomes:

    1. Twice as great
    2. Four times as great Correct answer.
    3. Half as great
    4. Unchanged

    Explanation

    Velocity pressure equals velocity squared divided by 4005 squared, so it changes with the square of velocity. Doubling the velocity multiplies the velocity pressure by four.

  60. Question 60Air Distribution

    When a damper on one branch is closed, airflow in the other branches of the same system changes. This interaction occurs mainly because the branches:

    1. Have identical equivalent lengths
    2. Share a common plenum pressure Correct answer.
    3. Are sized at the same friction rate
    4. Are fitted with the same diffusers

    Explanation

    Every branch is fed from the same plenum and sees the same static pressure at its inlet. Restricting one branch changes total flow and the plenum pressure, which then alters the flow through all the other branches, so balancing must be done in sequence with repeat passes.

  61. Question 61Gas Heating

    What manifold pressure is typical for a natural gas furnace at sea level?

    1. 10.0 in. w.c.
    2. 7.0 in. w.c.
    3. 3.5 in. w.c. Correct answer.
    4. 13.5 in. w.c.

    Explanation

    Natural gas appliances are normally set to about 3.5 in. w.c. manifold pressure at sea level, while propane appliances run much higher. Deviating from the manufacturer's rating changes the input rate and degrades combustion.

  62. Question 62Gas Heating

    What is the function of a thermocouple in a standing-pilot gas furnace?

    1. It produces a millivolt signal that holds the valve open Correct answer.
    2. It opens the gas valve on a call for heat from the thermostat
    3. It measures the temperature of the flue gases
    4. It senses flame by measuring flame rectification current

    Explanation

    A thermocouple heated by the pilot flame generates a small DC millivolt output that energizes the safety magnet in the gas valve. If the pilot goes out, the output falls and the valve closes.

  63. Question 63Gas Heating

    In what unit is flame current measured when testing a flame sensor rod?

    1. Millivolts AC
    2. Ohms
    3. Microamps DC Correct answer.
    4. Milliamps AC

    Explanation

    A flame rod circuit works by rectification: the flame conducts current in one direction, producing a small direct current. A healthy signal is typically in the range of a few microamps DC.

  64. Question 64Gas Heating

    Where should a sediment trap be installed on an appliance gas supply line?

    1. At the low point of a vertical drop near the appliance Correct answer.
    2. At the top of the vertical riser above the gas valve
    3. On the horizontal run at least 10 ft upstream
    4. Inside the appliance cabinet downstream of the manifold

    Explanation

    A sediment trap or drip leg belongs at the bottom of a vertical drop close to the appliance inlet, upstream of the gas valve. Pipe scale and dirt settle there instead of passing through the valve.

  65. Question 65Gas Heating

    Which flame appearance indicates a properly adjusted natural gas burner?

    1. White and lifting off the burner ports
    2. Blue with a crisp inner cone Correct answer.
    3. Bright orange with tall lazy tips
    4. Yellow with soot on the heat exchanger

    Explanation

    A stable blue flame with a well-defined inner cone shows the correct air-to-gas mixture and manifold pressure. Lifting, yellowing, or sooting all point to a mixture or pressure problem.

  66. Question 66Gas Heating

    What is primary air in a gas burner assembly?

    1. Air drawn into the flue after combustion
    2. Air supplied by the induced draft blower downstream of the burners
    3. Air mixed with gas before it reaches the burner ports Correct answer.
    4. Air used to cool the heat exchanger

    Explanation

    Primary air is entrained with the gas ahead of the burner ports and controls flame shape and color. Secondary air is drawn to the flame after the gas leaves the ports.

  67. Question 67Gas Heating

    While all other appliances are off, a furnace burns 2 cubic feet of natural gas (1,000 Btu per cubic foot) in 60 seconds. What is the input rate?

    1. 120,000 Btu/hr Correct answer.
    2. 90,000 Btu/hr
    3. 240,000 Btu/hr
    4. 60,000 Btu/hr

    Explanation

    Two cubic feet per minute equals 120 cubic feet per hour. Multiplying by 1,000 Btu per cubic foot gives an input of 120,000 Btu/hr, which is then compared to the rating plate.

  68. Question 68Gas Heating

    A rollout switch on a gas furnace has tripped and must be reset. Which condition most likely caused it to open?

    1. A dirty flame sensor that cannot prove flame
    2. A thermocouple that has lost its pilot signal
    3. Flame spilling from the burner box due to a blocked flue Correct answer.
    4. Gas supply pressure that is far below the manifold rating

    Explanation

    Rollout switches are temperature devices mounted near the burner box that open when flame spills out of the combustion area. Blocked flues, restricted combustion air, and heat exchanger defects are common causes. The cause must be corrected before resetting.

  69. Question 69Gas Heating

    What does the pressure switch prove in a furnace with an induced draft blower?

    1. That the thermostat is calling for heat
    2. That the gas valve has opened fully
    3. That the condensate trap is draining
    4. That the inducer is proving airflow before ignition Correct answer.

    Explanation

    The pressure switch closes only when the inducer develops enough draft through the heat exchanger. It is wired in series with the ignition control so the burners cannot fire without proven airflow.

  70. Question 70Gas Heating

    A 100,000 Btu/hr furnace is installed at 5,000 ft elevation and the manufacturer specifies a 4 percent derate per 1,000 ft. What is the derated input rating?

    1. 60,000 Btu/hr
    2. 80,000 Btu/hr Correct answer.
    3. 96,000 Btu/hr
    4. 100,000 Btu/hr

    Explanation

    Five thousand feet of elevation at 4 percent per 1,000 ft is a 20 percent reduction. Applying that to 100,000 Btu/hr leaves 80,000 Btu/hr, usually by changing orifices and resetting manifold pressure.

  71. Question 71Gas Heating

    A 100,000 Btu/hr furnace is in a confined space with two permanent openings to the same room. Using the standard one square inch per 1,000 Btu/hr rule, what minimum free area does each opening need?

    1. 50 sq in.
    2. 25 sq in.
    3. 100 sq in. Correct answer.
    4. 200 sq in.

    Explanation

    Each of the two openings is sized at one square inch of free area per 1,000 Btu/hr of total input. With 100,000 Btu/hr input, each opening needs 100 square inches of free area.

  72. Question 72Gas Heating

    How must a single-wall flue connector from a natural draft furnace be sloped?

    1. Downward toward the furnace at 1/4 in. per foot
    2. Upward toward the chimney at 1/4 in. per foot Correct answer.
    3. Horizontal, with no slope at all
    4. Upward at 1 in. per foot

    Explanation

    Flue pipe rises at least 1/4 in. per foot of run in the direction of flow so buoyant flue gases travel to the chimney. The slope also keeps acidic condensate from pooling in the connector.

  73. Question 73Gas Heating

    Combustion analysis on a natural gas furnace shows a flue CO2 reading well below normal with no measurable carbon monoxide. What does this indicate?

    1. Incomplete combustion caused by too little air
    2. A flue that has become restricted
    3. A heat exchanger with a crack
    4. Excessive excess air from too much dilution air Correct answer.

    Explanation

    The CO2 in flue gas falls when more air than needed is supplied, because the extra air dilutes the products of combustion. Oxygen readings rise at the same time while CO stays low if combustion is otherwise clean.

  74. Question 74Gas Heating

    What is the proper way to check a suspected gas leak at a threaded union?

    1. Rely on the odorant smell at the joint
    2. Pressurize the line with oxygen and watch the gauge
    3. Apply soap solution and watch for bubbles Correct answer.
    4. Hold a lit match near the joint

    Explanation

    A non-corrosive bubble solution applied to the joint will show bubbles if gas is escaping. Electronic detectors can also be used, but a flame or pure oxygen must never be introduced to a gas line.

  75. Question 75Gas Heating

    What is the purpose of a spill switch on a furnace equipped with a draft hood?

    1. Proves the inducer is running
    2. Shuts the burner off when flue gas spills Correct answer.
    3. Detects a standing pilot flame
    4. Limits the supply air temperature

    Explanation

    A spill switch senses heat at the draft hood and opens the safety circuit when flue products escape into the space instead of going up the vent. Blocked flues and depressurization are common causes of spillage.

  76. Question 76Gas Heating

    A furnace cycles on its high-limit switch with a clean filter. Which condition is the most likely cause?

    1. A flame sensor with a carbon-coated rod
    2. A thermocouple that has drifted out of specification
    3. Restricted airflow across the heat exchanger Correct answer.
    4. A thermostat wired to the wrong terminal

    Explanation

    The high limit opens when the heat exchanger overheats, which happens when the blower moves too little air. Closed registers, crushed ducts, a dirty evaporator coil, or a failing blower can all cause it.

  77. Question 77Gas Heating

    A flue gas analyzer shows 300 ppm CO and 4.9 percent O2. What is the air-free CO reading?

    1. 392 ppm Correct answer.
    2. 300 ppm
    3. 230 ppm
    4. 522 ppm

    Explanation

    Air-free CO equals measured CO multiplied by 20.9 divided by the difference between 20.9 and the measured O2. Here 300 x 20.9 / 16.0 equals about 392 ppm, the value compared against the acceptable limit.

  78. Question 78Gas Heating

    An 80,000 Btu/hr output furnace moves 1,200 CFM. What temperature rise should be measured across the heat exchanger?

    1. 37°F
    2. 45°F
    3. 75°F
    4. 62°F Correct answer.

    Explanation

    Temperature rise equals output Btu/hr divided by CFM times 1.08, so 80,000 divided by 1,296 equals about 62°F. That rise should fall inside the range printed on the rating plate.

  79. Question 79Gas Heating

    What must be changed when a furnace is converted from natural gas to propane?

    1. No changes; the furnace is dual-fuel as shipped
    2. Change only the manifold pressure regulator spring
    3. Change only the burner orifices to the LP size
    4. Change both the orifices and the gas valve regulator Correct answer.

    Explanation

    Propane is much denser in Btu content than natural gas, so smaller orifices and a higher manifold pressure (about 10 in. w.c.) are required. The manufacturer's conversion kit supplies both, and the data plate must be marked.

  80. Question 80Gas Heating

    A hot surface ignition furnace lights the burners, but they drop out after about 3 seconds and the valve closes. Which cause fits these symptoms?

    1. A failed inducer motor
    2. An open high-limit switch
    3. A defective hot surface igniter
    4. A dirty or failed flame sensor Correct answer.

    Explanation

    Burners that light and then drop out show the control is not receiving flame current. A dirty, bent, or poorly grounded flame sensor stops the control from proving flame proof.

  81. Question 81Heat Pump

    Which component changes the direction of refrigerant flow so that a single system can both heat and cool?

    1. Crankcase heater
    2. Thermostatic expansion valve
    3. Reversing valve Correct answer.
    4. Suction accumulator

    Explanation

    The reversing valve swaps the discharge and suction connections between the indoor and outdoor coils, which exchanges the roles of evaporator and condenser and lets the same circuit heat or cool.

  82. Question 82Heat Pump

    What is the purpose of auxiliary electric resistance heat in a heat pump system?

    1. To supplement heat pump output in cold weather Correct answer.
    2. To defrost the outdoor coil in winter
    3. To raise refrigerant superheat at the indoor coil
    4. To replace the compressor during cooling operation

    Explanation

    Auxiliary heat is sized to make up the gap between heat pump capacity and building heat loss once outdoor temperature falls below the balance point.

  83. Question 83Heat Pump

    On most residential heat pumps, what happens to the outdoor fan during a defrost cycle?

    1. It runs at high speed to melt the frost
    2. It reverses its rotation
    3. It runs at reduced speed
    4. It is stopped Correct answer.

    Explanation

    Stopping the outdoor fan allows coil temperature to climb quickly so hot discharge gas can clear the frost in the shortest time and limit cold blow indoors.

  84. Question 84Heat Pump

    At mild outdoor temperatures, how does the heating efficiency of an air-source heat pump compare with electric resistance heat?

    1. It is about the same
    2. It is slightly lower
    3. It is much lower
    4. It is significantly higher Correct answer.

    Explanation

    A heat pump moves existing heat rather than creating it, so it delivers roughly two to four units of heat per unit of electrical input, far above the COP of 1.0 for resistance elements.

  85. Question 85Heat Pump

    A crankcase heater is energized during the off cycle primarily to do what?

    1. Melt frost from the outdoor coil during a defrost cycle
    2. Speed recovery of the system after a defrost cycle ends
    3. Prevent refrigerant migration into the compressor oil Correct answer.
    4. Raise the discharge line temperature above the condensing point

    Explanation

    Warming the crankcase keeps the oil hotter than the coldest refrigerant in the system so refrigerant does not condense in the oil and dilute lubrication at startup.

  86. Question 86Heat Pump

    The O/B terminal on a heat pump thermostat is used to do what?

    1. Monitor outdoor coil temperature
    2. Control the outdoor fan motor
    3. Energize the auxiliary heat strips
    4. Select the reversing valve position Correct answer.

    Explanation

    The O or B terminal is the reversing valve output; depending on the manufacturer it is energized in cooling (O) or in heating (B), which determines the valve's default position.

  87. Question 87Heat Pump

    In the heating mode, which coil serves as the condenser?

    1. The indoor coil Correct answer.
    2. The outdoor coil
    3. The liquid line drier
    4. The suction accumulator

    Explanation

    In heating, the reversing valve routes hot discharge gas to the indoor coil, making it the condenser that rejects heat to the airstream, while the outdoor coil becomes the evaporator.

  88. Question 88Heat Pump

    What typically initiates a defrost cycle on a demand-defrost heat pump?

    1. An elapsed-time timer only, with no temperature sensing
    2. Low outdoor coil temperature sensed by the control board Correct answer.
    3. A drop in indoor return air temperature
    4. A rise in compressor discharge pressure

    Explanation

    Demand-defrost controls combine an elapsed run timer with coil temperature sensing so that defrost begins only after frost has actually depressed coil temperature and reduced performance.

  89. Question 89Heat Pump

    Most demand-defrost controls terminate the defrost cycle when which condition is met?

    1. Coil temperature rises to a set level Correct answer.
    2. Suction pressure falls to zero psig
    3. A fixed ten-minute backup timer expires
    4. Indoor fan pressure switch proves airflow

    Explanation

    Defrost ends when the coil temperature sensor or defrost thermostat proves the coil has warmed enough to melt all frost, typically around 50 to 70 degrees coil temperature.

  90. Question 90Heat Pump

    The balance point of a heat pump installation is the outdoor temperature at which what occurs?

    1. The heat pump locks out and defrost begins
    2. The compressor reaches maximum current draw
    3. Auxiliary heat is fully staged on
    4. Heat pump capacity equals the building heat loss Correct answer.

    Explanation

    At the balance point the heat pump's output exactly matches the structure's heat loss; below that temperature the heat pump alone cannot hold setpoint and auxiliary heat makes up the difference.

  91. Question 91Heat Pump

    On a heat pump that uses pistons at both coils, which device meters refrigerant at the outdoor coil during the heating cycle?

    1. The indoor piston, flowing in its normal direction
    2. The liquid line filter-drier
    3. The suction line accumulator
    4. A dedicated outdoor piston or outdoor TXV Correct answer.

    Explanation

    In heating the outdoor coil is the evaporator, so refrigerant is metered by the outdoor piston or outdoor TXV while the indoor piston is bypassed by its check valve.

  92. Question 92Heat Pump

    When checking the charge on a fixed-orifice heat pump that is operating in the heating mode, which measurement should the technician use?

    1. Superheat measured at the outdoor unit vapor line Correct answer.
    2. The approach method at the indoor coil
    3. Compressor amp draw alone
    4. Subcooling measured at the outdoor service valve

    Explanation

    With a fixed orifice in heating, the outdoor piston meters the flow, so manufacturers publish superheat targets measured at the outdoor unit's vapor service valve.

  93. Question 93Heat Pump

    What is the purpose of the suction line accumulator in a heat pump?

    1. To separate oil from the discharge gas
    2. To keep liquid refrigerant out of the compressor Correct answer.
    3. To store liquid refrigerant during the heating cycle
    4. To raise suction pressure during defrost

    Explanation

    The accumulator is a vessel on the suction line that lets any liquid slug boil off while oil is metered back to the compressor, protecting it during defrost and low-load operation.

  94. Question 94Heat Pump

    How does emergency heat mode differ from auxiliary heat operation?

    1. It alternates the compressor and the strip heaters
    2. It locks out the compressor and uses strip heat Correct answer.
    3. It uses only the compressor
    4. It runs the compressor and the strip heaters together

    Explanation

    Emergency heat is a manual mode in which the compressor is locked out and the strip heaters carry the entire load, typically used when the outdoor unit has failed.

  95. Question 95Heat Pump

    Which condition is most likely if a heat pump has excessive indoor airflow in the heating mode?

    1. Frequent, short defrost cycles
    2. High head pressure and a cold indoor coil
    3. Lower supply air temperature and reduced comfort Correct answer.
    4. Low suction pressure and a frosted outdoor coil

    Explanation

    Excess airflow moves more air across the indoor condenser than the coil can heat, so the temperature rise across the coil and the supply air temperature both fall.

  96. Question 96Heat Pump

    A heat pump running in heating at 5 degrees outdoor temperature shows lower-than-normal suction pressure. Which explanation is most fundamental?

    1. The compressor valves are leaking by badly
    2. Refrigerant density and coil capacity drop with ambient Correct answer.
    3. The indoor coil has iced over completely
    4. The reversing valve has shifted to the cooling position

    Explanation

    As outdoor temperature falls, both the heat available to the outdoor coil and the refrigerant's saturated pressure drop, so suction pressure falls with ambient even on a correctly charged system.

  97. Question 97Heat Pump

    On a dual-fuel system that pairs a heat pump with a gas furnace, what is the function of the fossil fuel kit or plenum switch?

    1. It stages the furnace by outdoor temperature
    2. It starts the furnace whenever a defrost begins
    3. It converts the system from heat pump to straight cooling
    4. It shuts off the heat pump while the furnace is firing Correct answer.

    Explanation

    A fossil fuel kit or plenum switch prevents the heat pump and furnace from operating at the same time, which would overheat the indoor coil and drive head pressure dangerously high.

  98. Question 98Heat Pump

    In the heating mode, a heat pump shows high suction pressure, low discharge pressure, and a cool indoor coil. Which is the most likely cause?

    1. A restricted liquid line drier
    2. A failed defrost termination
    3. An inefficient compressor Correct answer.
    4. Low refrigerant charge

    Explanation

    When the compressor cannot develop a normal pressure difference, suction stays high and discharge stays low, so little hot gas reaches the indoor coil and supply air remains cool.

  99. Question 99Heat Pump

    A heat pump remains in defrost indefinitely even though the outdoor coil is clear of frost. Which is the most likely cause?

    1. A stuck defrost sensor or control board Correct answer.
    2. A failed outdoor fan motor that never runs
    3. A heavily clogged indoor air filter
    4. A low refrigerant charge in the system

    Explanation

    Defrost ends only when the coil sensor signals that frost has cleared; if the sensor or the board is stuck in the defrost position, the control never terminates the cycle.

  100. Question 100Heat Pump

    Why is auxiliary heat typically energized during a defrost cycle?

    1. To shorten the length of the defrost cycle
    2. To raise the outdoor coil pressure faster
    3. To keep supply air from feeling cold Correct answer.
    4. To keep the compressor from overloading

    Explanation

    While the unit is in defrost the indoor coil is removing heat from the airstream, so the strip heaters temper the supply air and maintain space comfort during the cycle.

  101. Question 101Oil Heating

    Approximately how many Btu are released by burning one gallon of No. 2 heating oil?

    1. 100,000 Btu
    2. 120,000 Btu
    3. 140,000 Btu Correct answer.
    4. 175,000 Btu

    Explanation

    No. 2 heating oil contains roughly 138,000 to 140,000 Btu per gallon, and this figure is the basis for every firing-rate and nozzle-size calculation. Technicians round it to 140,000 Btu per gallon when matching a nozzle to an appliance.

  102. Question 102Oil Heating

    Oil burner nozzle capacities in gallons per hour are rated at which nozzle pressure?

    1. 200 psi
    2. 150 psi
    3. 100 psi Correct answer.
    4. 50 psi

    Explanation

    The industry rates nozzles at 100 psi, so a 1.00 gph nozzle delivers one gallon per hour only when the pump produces 100 psi at the nozzle. Any other pump pressure requires converting the rating with the square-root rule.

  103. Question 103Oil Heating

    What is the function of the cad cell in an oil burner primary control?

    1. It measures flue gas temperature
    2. It limits boiler water temperature
    3. It proves that a flame is present Correct answer.
    4. It regulates oil pump pressure

    Explanation

    A cadmium sulfide photocell drops sharply in resistance when flame light strikes it, and the primary control uses that change to hold the burner on or to lock out on flame failure. It is a flame-sensing device only.

  104. Question 104Oil Heating

    What secondary voltage is typical of an oil burner ignition transformer?

    1. 10,000 volts Correct answer.
    2. 1,000 volts
    3. 5,000 volts
    4. 2,500 volts

    Explanation

    Gun-type oil burners commonly use a 10,000 volt, 20 milliampere transformer so the spark can jump the electrode gap through the oil spray. Lower voltages are used on other ignition devices but not on standard oil burner electrodes.

  105. Question 105Oil Heating

    The most common oil storage tank installed in a residential basement holds how much?

    1. 275 gallons Correct answer.
    2. 500 gallons
    3. 150 gallons
    4. 330 gallons

    Explanation

    The standard basement tank is the 275 gallon vertical oval, sized to fit through a doorway and against a wall. Other sizes exist, but 275 gallons is the usual residential indoor tank.

  106. Question 106Oil Heating

    A properly adjusted No. 2 oil burner should produce what smoke spot number?

    1. 0 to 1 Correct answer.
    2. 6 to 7
    3. 2 to 3
    4. 4 to 5

    Explanation

    Smoke is rated on a 0 to 9 spot scale, and a clean, correctly adjusted burner should test at 0 to 1. Higher numbers mean visible smoke, soot formation, and wasted fuel.

  107. Question 107Oil Heating

    A 1.00 gph nozzle stamped at 100 psi is operated at 144 psi. What is the approximate delivery rate?

    1. 1.10 gph
    2. 0.83 gph
    3. 1.20 gph Correct answer.
    4. 1.44 gph

    Explanation

    Nozzle flow changes with the square root of the pressure ratio. The square root of 144/100 is 1.2, so the nozzle delivers about 1.20 gph at 144 psi.

  108. Question 108Oil Heating

    A burner is installed with the storage tank below the burner and a suction lift of about six feet. Which supply arrangement is required?

    1. Single-pipe gravity feed with no return line
    2. Two-pipe system with a return line to the tank Correct answer.
    3. A larger nozzle to offset reduced pump capacity
    4. Single-pipe system with a suction-line check valve only

    Explanation

    A single-pipe system depends on a gravity head from a tank above the burner. With the tank below, a two-pipe arrangement with a return line lets the pump purge air and maintain suction within the manufacturer's lift limits.

  109. Question 109Oil Heating

    What overfire draft is typical for a residential oil-fired boiler?

    1. -0.02 in. w.c. Correct answer.
    2. -2.0 in. w.c.
    3. -0.20 in. w.c.
    4. +0.02 in. w.c.

    Explanation

    Roughly -0.02 in. w.c. over the fire holds combustion products in the chamber while limiting infiltration of excess air. Breech draft is normally a bit stronger, around -0.04 to -0.06 in. w.c.

  110. Question 110Oil Heating

    Which carbon dioxide reading indicates a properly adjusted No. 2 oil burner?

    1. 11.5 to 12.5 percent Correct answer.
    2. 14 to 15 percent
    3. 6 to 8 percent
    4. 3 to 5 percent

    Explanation

    The theoretical maximum CO2 for No. 2 oil is about 15.4 percent, but practical settings are 11.5 to 12.5 percent with a smoke spot of 0 to 1. Running as close to that band as smoke allows gives the best combustion efficiency.

  111. Question 111Oil Heating

    What electrode gap is typical for a gun-type oil burner?

    1. 1/16 in.
    2. 3/8 in.
    3. 1/8 in. Correct answer.
    4. 1/32 in.

    Explanation

    Most gun burners specify a 1/8 in. gap between the electrode tips, set just ahead of and slightly above the nozzle centerline. Too wide a gap overloads the transformer, and too narrow a gap carbon-fouls quickly.

  112. Question 112Oil Heating

    A burner produces a puffback at startup. Which condition most likely causes it?

    1. The barometric damper is set too far open
    2. Oil accumulates in the chamber before ignition Correct answer.
    3. Combustion air is excessive
    4. The nozzle is undersized for the firing rate

    Explanation

    A puffback is delayed ignition: oil collects in the combustion chamber and then ignites all at once. Causes include a weak spark, misaligned electrodes, a dirty nozzle, or poor draft.

  113. Question 113Oil Heating

    What device is required when an oil storage tank is installed above the burner?

    1. A second in-line filter
    2. An oil safety valve at the tank outlet Correct answer.
    3. A vacuum gauge on the pump inlet
    4. A fusible plug in the burner housing

    Explanation

    An oil safety valve opens only while the burner is running, so a broken line or failed pump seal cannot allow gravity flow of oil. It is the standard protection whenever the tank outlet is higher than the burner.

  114. Question 114Oil Heating

    After a single-pipe oil line has been run dry, why must the fuel unit be bled?

    1. The pump loses its bypass plug
    2. The cad cell requires light to function
    3. Trapped air prevents the pump from building pressure Correct answer.
    4. The nozzle must be flushed of sludge

    Explanation

    Air trapped in the pump and suction line makes the pump chatter and prevents it from reaching the 100 psi needed for proper atomization. Opening the bleeder valve with the burner running purges that air.

  115. Question 115Oil Heating

    A vacuum gauge on a two-pipe oil pump reads 12 in. Hg. What does this most likely indicate?

    1. A normal reading for a short, clean line
    2. A pump that has lost its prime completely
    3. A typical reading that needs no attention
    4. A restricted or undersized suction line Correct answer.

    Explanation

    Normal two-pipe vacuum readings are in the low single digits to about 10 in. Hg. A reading near 12 in. Hg points to a clogged filter, kinked line, or undersized suction line, and high vacuum can cause air separation and erratic firing.

  116. Question 116Oil Heating

    A boiler's stack temperature is much higher than normal while CO2 and draft remain within range. Which cause fits best?

    1. Excess combustion air admitted at the damper
    2. An undersized burner nozzle
    3. A partially blocked chimney flue
    4. Soot or scale insulating the heat exchanger Correct answer.

    Explanation

    A coated heat exchanger blocks heat transfer from the flue gases to the water, so more heat leaves up the stack and steady-state efficiency drops. The combustion readings themselves can still look normal.

  117. Question 117Oil Heating

    An oil-fired boiler must deliver 105,000 Btu/hr output at 80 percent combustion efficiency. Which nozzle is the closest match?

    1. 0.75 gph
    2. 0.95 gph Correct answer.
    3. 0.65 gph
    4. 1.25 gph

    Explanation

    Required input is 105,000 divided by 0.80, or about 131,000 Btu/hr. Dividing by 140,000 Btu per gallon gives roughly 0.94 gph, so a 0.95 gph nozzle is the closest standard size.

  118. Question 118Oil Heating

    A burner locks out, and with the burner off an ohmmeter across the cad cell reads about 300 ohms in a dark boiler room. What does this indicate?

    1. The cell has failed open and must be replaced
    2. The cell is shorted internally or through its wiring Correct answer.
    3. The cell only needs to be cleaned of soot
    4. The cell is normal and the fault is elsewhere

    Explanation

    A dark cad cell should read in the tens of thousands of ohms or higher. A few hundred ohms in darkness means the photocell or its leads are shorted, so the control is fooled into seeing flame when there is none.

  119. Question 119Oil Heating

    Ignition at the nozzle is intermittent even though the transformer tests good and the gap is correct. Which condition most reduces spark voltage at the electrode tips?

    1. Low oil pump cut-off pressure
    2. A missing nozzle adapter gasket
    3. Cracked or carbon-tracked electrode insulators Correct answer.
    4. A dirty nozzle line strainer

    Explanation

    Cracked porcelain or carbon tracks along the insulators give the high voltage an easier path to ground, so the spark shunts away from the gap. The transformer can test fine on the bench and still fail to fire the burner.

  120. Question 120Oil Heating

    An oil furnace shows normal combustion readings at the burner, but carbon monoxide is elevated in the supply air plenum. What is the most likely cause?

    1. The heat exchanger is cracked Correct answer.
    2. The barometric damper is stuck wide open
    3. The nozzle is oversized for the furnace
    4. Combustion air is excessive

    Explanation

    Combustion gases can only reach the supply airstream through a breach in the heat exchanger, such as a crack or failed gasket. The burner itself can test perfectly while flue products leak into the circulated air.

  121. Question 121Hydronics (Gas and Oil)

    What is the primary function of the expansion tank in a closed hot water heating system?

    1. Increase the flow rate through the system piping
    2. Separate entrained air from the water before it enters the boiler
    3. Absorb the volume increase of water as it is heated Correct answer.
    4. Lower the flue gas temperature at the boiler outlet

    Explanation

    Water expands as it is heated, and a closed hydronic system has nowhere for that added volume to go. The expansion tank contains a captive air cushion that compresses to accept the volume while holding system pressure between the fill pressure and the relief setting.

  122. Question 122Hydronics (Gas and Oil)

    A pressure relief valve on a typical residential hot water heating boiler is rated to open at approximately:

    1. 60 psig
    2. 15 psig
    3. 45 psig
    4. 30 psig Correct answer.

    Explanation

    Residential hot water boilers are ordinarily protected by a 30 psig relief valve, which is above normal operating pressure but below the pressure the boiler and its components can safely contain. The fill valve is set well below that value so the relief does not weep in normal operation.

  123. Question 123Hydronics (Gas and Oil)

    Where should a manual air vent be installed in a hydronic piping system?

    1. At the highest point of the piping system Correct answer.
    2. At the lowest point of the system, near the boiler drain
    3. On the discharge of the circulator
    4. At the return connection on the boiler

    Explanation

    Air is lighter than water and rises, so it collects at high points, at the tops of risers, and in the upper part of terminal units. Vents placed there release the trapped air that would otherwise stop circulation.

  124. Question 124Hydronics (Gas and Oil)

    The main purpose of the high-limit aquastat on a hot water boiler is to:

    1. Stop burner operation at a set boiler water temperature Correct answer.
    2. Shut the burner down if flue gas temperature rises too high
    3. Hold the domestic hot water coil at a constant temperature
    4. Vary circulator speed as the heating load changes

    Explanation

    The high-limit aquastat is a safety control that opens the burner circuit when boiler water reaches its setpoint, typically in the 180°F to 200°F range. It works independently of the operating control that cycles the burner to hold temperature.

  125. Question 125Hydronics (Gas and Oil)

    In a properly piped system, the circulator is installed so that it pumps away from the expansion tank connection. This arrangement keeps the:

    1. Air separator operating at its rated capacity
    2. System fill pressure below the relief valve setting
    3. Boiler water temperature nearly uniform throughout the loop
    4. Expansion tank connection at the point of no pressure change Correct answer.

    Explanation

    When the pump discharges away from the tank, the tank connection becomes the point of no pressure change: the pump's pressure rise appears downstream and its pressure drop upstream. This prevents the pump from pushing water in and out of the tank and keeps sub-atmospheric pressure out of the upper parts of the system.

  126. Question 126Hydronics (Gas and Oil)

    A flow-check valve installed at a zone circulator is intended to prevent:

    1. Air from entering the zone when the circulator stops
    2. The relief valve from weeping at high water temperature
    3. Gravity circulation through the zone while its circulator is off Correct answer.
    4. Excessive pump head at design flow

    Explanation

    A flow check closes when its circulator stops so that buoyant hot water cannot migrate through an unoccupied zone by gravity. Without it, the zone would heat when it should be off and other zones would be starved of flow.

  127. Question 127Hydronics (Gas and Oil)

    In primary/secondary piping, closely spaced tees between the boiler loop and the distribution loop are used to:

    1. Provide a convenient point for air separation
    2. Increase velocity through the secondary loop
    3. Hydraulically separate the boiler loop from the secondary circuits Correct answer.
    4. Prevent boiler water from entering the secondary loop

    Explanation

    Closely spaced tees create almost no pressure drop between the supply and return of the primary loop, so the secondary pump's head is not added to the boiler pump's head and neither loop forces flow through the other. This is hydraulic separation, and it lets each circuit be sized and controlled independently.

  128. Question 128Hydronics (Gas and Oil)

    Oil burner nozzle flow ratings are published at a nozzle pressure of:

    1. 150 psig
    2. 50 psig
    3. 75 psig
    4. 100 psig Correct answer.

    Explanation

    Nozzle capacity tables are based on 100 psig at the nozzle, together with a specified spray angle and pattern. Any other pump pressure requires a correction to the rated flow.

  129. Question 129Hydronics (Gas and Oil)

    A 1.00 gph nozzle rated at 100 psig is operated at 144 psig. Its flow rate becomes approximately:

    1. 1.10 gph
    2. 1.20 gph Correct answer.
    3. 1.44 gph
    4. 0.83 gph

    Explanation

    Nozzle flow varies with the square root of the pressure: new flow equals rated flow times the square root of (new pressure divided by 100). The square root of 1.44 is 1.2, so the nozzle flows about 1.20 gph.

  130. Question 130Hydronics (Gas and Oil)

    Excessive excess air in an oil-fired boiler primarily causes:

    1. Reduced efficiency from heat carried up the stack Correct answer.
    2. Rapid carbon buildup on the nozzle tip
    3. Smoke and high carbon monoxide levels
    4. Flame impingement on the rear refractory

    Explanation

    Air beyond what is needed for complete combustion is heated in the combustion zone and then discharged up the chimney, and it also lowers CO2 and flame temperature. The result is a measurable loss in combustion efficiency even though the stack temperature may drop slightly.

  131. Question 131Hydronics (Gas and Oil)

    An oil-fired boiler's barometric draft regulator is normally adjusted to hold a breech draft of about:

    1. +0.05 in. w.c. (positive)
    2. -0.50 in. w.c. (negative)
    3. -0.02 in. w.c. (negative) Correct answer.
    4. 0.00 in. w.c. (neutral)

    Explanation

    Oil burners need a steady, slightly negative draft at the breech, commonly around -0.02 in. w.c., with a matching negative overfire draft. Too much negative draft pulls heat up the stack, and positive pressure allows flue gases to escape into the building.

  132. Question 132Hydronics (Gas and Oil)

    The low-water cutoff on a hot water boiler serves to:

    1. Shut off the burner if the water level falls below a safe point Correct answer.
    2. Prevent the relief valve from opening during expansion
    3. Sound an alarm only while the boiler is firing
    4. Add make-up water automatically when the level drops

    Explanation

    The low-water cutoff proves that water covers the boiler's hottest surfaces. If the level drops below a safe point, it opens the burner circuit so the sections are not overheated and cracked.

  133. Question 133Hydronics (Gas and Oil)

    Which terminal unit normally requires the lowest supply water temperature?

    1. Fin-tube baseboard
    2. Cast-iron radiators
    3. Fan-coil unit
    4. Radiant floor tubing Correct answer.

    Explanation

    Radiant floors spread heat over a large surface, so they produce their rated output with water in roughly the 90°F to 140°F range. Fin-tube baseboard, cast-iron radiators, and fan coils are rated at higher water temperatures, commonly 180°F average.

  134. Question 134Hydronics (Gas and Oil)

    Compared with water, a 50% propylene glycol solution requires the designer to:

    1. Lower the boiler aquastat setting
    2. Increase pump head and allow for greater expansion volume Correct answer.
    3. Use a smaller expansion tank
    4. Reduce the relief valve setting

    Explanation

    Glycol is more viscous and holds less heat per gallon than water, so higher flow and more pump head are needed for the same heat output. It also expands more when heated, so a larger expansion tank is required.

  135. Question 135Hydronics (Gas and Oil)

    The fill (pressure-reducing) valve on a hot water heating system is normally set to:

    1. 5 psi regardless of building height
    2. The static head of the system plus about 4 to 5 psi at the top Correct answer.
    3. The same pressure as the relief valve setting
    4. 30 psi on all residential systems

    Explanation

    Fill pressure must overcome the static pressure of the water column, which is about 0.433 psi per foot of height, and still leave 4 to 5 psi at the highest point so air cannot enter. The setting is always kept well below the relief valve setting.

  136. Question 136Hydronics (Gas and Oil)

    The advantage of reverse-return piping on a two-pipe hydronic system is that it:

    1. Reduces the total length of pipe required
    2. Allows the use of smaller circulators
    3. Provides nearly equal pressure drop through each terminal Correct answer.
    4. Eliminates the need for an expansion tank

    Explanation

    In a reverse-return layout the supply reaches the farthest terminal and the return starts at the nearest, so each circuit contains nearly the same pipe length and fittings. The result is roughly equal pressure drop at every terminal, which makes balancing far easier.

  137. Question 137Hydronics (Gas and Oil)

    A hot water boiler short-cycles on its high limit while the house stays cold. Which is the most likely cause?

    1. The circulator is air-locked and not moving water Correct answer.
    2. The relief valve is weeping
    3. The aquastat differential is set too wide
    4. The expansion tank is waterlogged

    Explanation

    With no water moving, the burner heats a small stagnant volume of boiler water to the limit quickly while very little heat reaches the rooms. Air locking, a failed circulator, or a closed isolation valve on the loop are the usual causes.

  138. Question 138Hydronics (Gas and Oil)

    Why is a cast-iron boiler protected from low return water temperature in a primary/secondary design?

    1. Flue gas condensation and thermal shock can damage the cast-iron sections. Correct answer.
    2. The expansion tank will become waterlogged at low temperature.
    3. The aquastat cannot sense supply temperature below 130°F.
    4. Cold return water greatly increases circulator head and flow.

    Explanation

    Oil and gas flue gases contain water vapor and sulfur compounds, so if the return water cools the flue gas below its dew point, corrosive condensate forms on the iron. A cold return also puts thermal stress on the sections, so boiler bypass or primary/secondary piping holds the return above roughly 130°F to 140°F.

  139. Question 139Hydronics (Gas and Oil)

    Residential fin-tube baseboard output ratings are published at a supply water temperature of about:

    1. 180°F Correct answer.
    2. 220°F
    3. 150°F
    4. 120°F

    Explanation

    Baseboard ratings are published at 180°F average water temperature, typically 200°F supply and 160°F return, with a room temperature near 65°F to 70°F. Ratings must be corrected when the system is designed for lower water temperatures.

  140. Question 140Hydronics (Gas and Oil)

    An outdoor reset control lowers boiler water temperature as outdoor temperature rises because:

    1. It increases circulator speed as outdoor temperature rises
    2. It raises the high limit to store more heat in mild weather
    3. It prevents the boiler from reaching condensing temperatures
    4. Warmer outdoor air reduces heat loss, so less heat input is needed Correct answer.

    Explanation

    Outdoor reset matches the water temperature to the building load. As it warms outside, the heat loss drops, so a lower supply temperature still holds the space at setpoint while reducing stack losses and short cycling.

  141. Question 141Light Commercial Air Conditioning

    In a packaged rooftop unit, what is the primary purpose of the economizer section?

    1. To lower the refrigerant charge during part-load operation
    2. To recover heat from exhaust air during the heating season
    3. To control condenser fan speed when outdoor air is cold
    4. To cool with outdoor air when conditions are favorable Correct answer.

    Explanation

    When outdoor air temperature or enthalpy is below the return air condition, the economizer dampers modulate open and mechanical cooling is staged off or reduced. This free cooling lowers compressor energy use.

  142. Question 142Light Commercial Air Conditioning

    Which part of a thermostatic expansion valve responds to the temperature at the evaporator outlet?

    1. The condenser fan cycling switch
    2. The remote bulb clamped to the suction line Correct answer.
    3. The equalizer line connected to the evaporator outlet
    4. The liquid line solenoid valve

    Explanation

    The remote bulb holds a charge that responds to the temperature at the evaporator outlet, and the resulting pressure acts on the diaphragm to reposition the valve and hold superheat. The external equalizer only compensates for pressure drop through the evaporator.

  143. Question 143Light Commercial Air Conditioning

    What is the main purpose of a crankcase heater on a commercial compressor?

    1. To limit compressor cycling during low-load conditions
    2. To raise discharge gas temperature at start-up
    3. To keep refrigerant from migrating into the crankcase Correct answer.
    4. To keep the oil at operating viscosity during the cooling cycle

    Explanation

    During the off cycle refrigerant migrates to the coldest part of the system, often the compressor crankcase. The crankcase heater keeps the oil warm enough that refrigerant does not condense into it and dilute the lubricant.

  144. Question 144Light Commercial Air Conditioning

    Why must the condensate drain of a draw-through evaporator coil have a trap?

    1. To prevent algae growth inside the drain line
    2. To keep the drain pan from corroding
    3. To allow the drain pan to be pitched toward either side
    4. To seal the drain against the cabinet's negative pressure Correct answer.

    Explanation

    In a draw-through arrangement the blower pulls the cabinet into a negative pressure, which would hold water in the pan or draw air back through the drain. A properly sized trap with the correct static height creates a water seal that allows drainage.

  145. Question 145Light Commercial Air Conditioning

    Which field change will reverse the rotation of a three-phase compressor motor?

    1. Swapping the two leads on the contactor coil
    2. Reversing the thermostat R and Y terminals
    3. Reversing the start and run capacitor connections
    4. Interchanging any two of the three supply conductors Correct answer.

    Explanation

    Three-phase rotation is set by the phase sequence of the supply. Exchanging any two of the three line conductors changes that sequence and reverses the rotation.

  146. Question 146Light Commercial Air Conditioning

    A return-air filter loaded well beyond its recommended pressure drop most directly causes which condition?

    1. Reduced airflow across the evaporator coil Correct answer.
    2. Higher-than-normal liquid line subcooling
    3. Increased compressor oil pressure
    4. Lower condenser approach temperature

    Explanation

    A restricted filter adds resistance on the inlet side of the blower, reducing the air volume delivered to the evaporator. Low evaporator airflow produces low suction pressure and possible coil icing.

  147. Question 147Light Commercial Air Conditioning

    A packaged unit has a TXV and a liquid sight glass. Which reading is the primary basis for verifying that the charge is correct?

    1. Suction line superheat measured at the compressor
    2. A clear sight glass at the expansion valve inlet
    3. Liquid line subcooling measured at the condenser outlet Correct answer.
    4. Compressor amperage compared with the nameplate RLA

    Explanation

    With a TXV, the valve holds evaporator superheat roughly constant, so superheat checks valve performance rather than charge. Charge is verified by measuring subcooling at the condenser outlet and comparing it with the manufacturer's target.

  148. Question 148Light Commercial Air Conditioning

    A packaged unit must cool when the outdoor ambient is 40°F. Which control keeps head pressure high enough for reliable operation?

    1. Condenser fan cycling or fan speed control Correct answer.
    2. Hot gas bypass to the evaporator
    3. A suction line accumulator
    4. A crankcase heater

    Explanation

    At low ambient the condenser is oversized and head pressure falls, starving the metering device and risking lubrication problems. Cycling the fan or reducing fan speed raises condensing pressure back toward normal.

  149. Question 149Light Commercial Air Conditioning

    What is the function of hot gas bypass on a DX commercial system?

    1. To shorten the compressor off cycle between cooling stages
    2. To raise the condensing pressure when the outdoor air is cold
    3. To purge non-condensable gases from the condenser during operation
    4. To prevent coil freeze-up and compressor cycling at low load Correct answer.

    Explanation

    At low load, refrigerant flow or airflow through the evaporator can drop enough to freeze the coil and cause compressor flooding or short cycling. Hot gas bypass injects discharge gas downstream of the metering device to maintain minimum load and suction pressure.

  150. Question 150Light Commercial Air Conditioning

    How does a cylinder unloader reduce compressor capacity?

    1. It drains excess refrigerant into the receiver
    2. It holds one cylinder's suction valves open Correct answer.
    3. It bypasses discharge gas to the suction line
    4. It slows the compressor motor to a lower speed

    Explanation

    An unloader holds the suction valves of one or more cylinders open, so gas is pushed back out on the upstroke instead of being compressed. Capacity drops in steps as cylinders are unloaded.

  151. Question 151Light Commercial Air Conditioning

    In a VAV system, which device modulates to maintain the temperature of an individual zone?

    1. The compressor unloading solenoid
    2. The condenser fan speed
    3. The outdoor air economizer damper
    4. The zone VAV box damper Correct answer.

    Explanation

    The zone thermostat repositions the VAV box damper, changing the airflow to that zone while the supply air stays at a roughly constant temperature. Duct static pressure is maintained by fan control or inlet vanes.

  152. Question 152Light Commercial Air Conditioning

    A three-phase compressor is supplied with line voltages of 208 V, 208 V, and 197 V. What is the voltage imbalance?

    1. About 3.6%, which exceeds the 2% limit Correct answer.
    2. About 5.6%, which is within the 10% allowance
    3. About 1.8%, which is acceptable
    4. About 3.6%, which is acceptable below 5%

    Explanation

    Average voltage is about 204 V and the largest deviation is about 7.3 V, so the imbalance is roughly 3.6 percent. NEMA allows no more than 2 percent; above that the motor must be derated or the supply corrected, because the imbalance causes current imbalance and overheating.

  153. Question 153Light Commercial Air Conditioning

    A technician measures 1.2 in. w.c. of external static pressure on a blower rated for 0.80 in. w.c. What does this indicate?

    1. The duct system is restrictive, so airflow is likely below design Correct answer.
    2. The blower is running too fast and the motor will overload
    3. The coil is overcharged and the extra pressure shows up as static
    4. The reading is normal because filters add pressure drop

    Explanation

    External static pressure reflects the resistance of the duct system and accessories. Reading well above the blower's rated static means the system is restrictive, so delivered airflow falls short of design and the motor may run cooler but the coil may ice.

  154. Question 154Light Commercial Air Conditioning

    Two identical units serve one building. Unit A reads 10°F subcooling and 10°F superheat. Unit B reads 21°F subcooling and 3°F superheat, with its sensing bulb tight, clean, and insulated. What is the most likely condition of Unit B?

    1. Failed compressor valves
    2. Restricted liquid line drier
    3. Undercharged
    4. Overcharged Correct answer.

    Explanation

    Subcooling above target together with superheat below target indicates excess liquid refrigerant backing up in the condenser, which is an overcharge. A properly mounted bulb rules out a sensing problem holding the valve open.

  155. Question 155Light Commercial Air Conditioning

    Why is differential enthalpy changeover often preferred over dry-bulb changeover for economizers in humid climates?

    1. It keeps the compressor running during free cooling
    2. It accounts for outdoor humidity, avoiding moist air that costs more to cool Correct answer.
    3. It eliminates the need for a return-air damper in the unit
    4. It allows the economizer to operate at any outdoor temperature without limits

    Explanation

    Enthalpy reflects total heat content, including latent load. In humid weather outdoor air can be cooler than return air by dry bulb yet carry a higher total load, so dry-bulb changeover would bring in air that increases compressor work.

  156. Question 156Light Commercial Air Conditioning

    A condensing unit has tripped on its high-pressure switch. What is the proper procedure before restoring operation?

    1. Add refrigerant to lower the head pressure
    2. Jumper the switch out until the building cools down
    3. Correct the cause, then reset the manual switch Correct answer.
    4. Reset the switch and restart the unit to see whether it holds

    Explanation

    A high-pressure trip is a symptom of condenser airflow restriction, overcharge, non-condensables, or a failed fan. The cause must be corrected before resetting, because repeated trips damage the compressor.

  157. Question 157Light Commercial Air Conditioning

    A 75 VA control transformer already supplies 30 VA of contactor coils, and the technician wants to add an economizer module rated at 50 VA. What is the correct conclusion?

    1. The connected load would be 80 VA, which is acceptable because economizer load is intermittent
    2. The connected load would be 80 VA, so a larger transformer is needed Correct answer.
    3. The transformer rating applies only to its primary winding, so the addition is fine
    4. The connected load would be 65 VA, so no change is needed

    Explanation

    The VA rating applies to the total connected secondary load, so 30 plus 50 equals 80 VA, which exceeds the 75 VA nameplate. The transformer must be replaced with one rated above the new total with margin.

  158. Question 158Light Commercial Air Conditioning

    A system is evacuated to 500 microns, isolated, and the gauge climbs to 1,500 microns in a few minutes and keeps rising. What does this indicate?

    1. That the system is ready to be charged
    2. That the system is overcharged with refrigerant
    3. A normal reading caused by oil outgassing
    4. A leak or moisture that must be found and corrected Correct answer.

    Explanation

    A standing vacuum test should hold near the achieved level, with only a small rise from outgassing. A continuous climb means air is entering the system or moisture is still boiling off, and that must be corrected before charging.

  159. Question 159Light Commercial Air Conditioning

    A technician installs an adjustable motor sheave on a belt-driven blower and sets its pitch diameter smaller than the original. What is the effect on blower performance?

    1. Blower rpm is unchanged but static pressure rises
    2. Blower rpm increases and airflow increases
    3. Blower rpm decreases but airflow stays the same
    4. Blower rpm and airflow both decrease Correct answer.

    Explanation

    Blower rpm follows the ratio of sheave diameters, so a smaller motor sheave turns the blower more slowly. The fan laws then reduce airflow roughly in proportion to the speed change.

  160. Question 160Light Commercial Air Conditioning

    What is the purpose of an auxiliary condensate overflow switch on a commercial air handler?

    1. To alarm only, with no effect on unit operation
    2. To drain the pan automatically when it fills
    3. To stop cooling before the pan overflows Correct answer.
    4. To shut off the condenser fan when the pan is full

    Explanation

    The switch is a float or probe installed in the drain pan or a secondary pan that opens the low-voltage cooling circuit when water reaches the trip point. This shuts down cooling so the pan cannot overflow and damage the building.

  161. Question 161Commercial Refrigeration

    Superheat is the difference between the actual temperature of the refrigerant vapor and the:

    1. evaporator entering air dry-bulb temperature
    2. outdoor ambient air temperature
    3. saturation temperature at that pressure Correct answer.
    4. condensing temperature minus 10°F

    Explanation

    Superheat is found by subtracting the saturation temperature that corresponds to the suction pressure from the measured suction line temperature. It confirms that all liquid has boiled off before the gas reaches the compressor.

  162. Question 162Commercial Refrigeration

    Subcooling at the condenser outlet is determined by comparing the liquid line temperature to the:

    1. outdoor dry-bulb temperature
    2. saturation temperature at head pressure Correct answer.
    3. suction line temperature at the compressor
    4. evaporator coil surface temperature

    Explanation

    Subcooling equals the saturation (condensing) temperature matching the head pressure minus the measured liquid line temperature. It verifies the refrigerant is fully liquid and that the condenser holds an adequate liquid seal.

  163. Question 163Commercial Refrigeration

    While the system runs at a steady load, a sight glass in the liquid line shows a continuous stream of bubbles. This most likely means:

    1. a low charge or a liquid line restriction Correct answer.
    2. the system is fully charged and operating normally
    3. the suction filter-drier is restricted
    4. the condenser is over-subcooled

    Explanation

    Continuous bubbling at a steady load indicates flash gas, usually from a low charge or a restriction such as a plugged filter-drier. A brief bubble at startup or right after a load change is normal.

  164. Question 164Commercial Refrigeration

    The purpose of a crankcase heater on a semi-hermetic compressor is to:

    1. keep refrigerant from condensing in the crankcase oil Correct answer.
    2. raise the discharge gas temperature during pulldown
    3. hold condenser pressure above the outdoor ambient
    4. warm the suction gas before it enters the cylinders

    Explanation

    The heater warms the oil sump so refrigerant that migrated during the off cycle is driven back out of the oil. This prevents oil dilution and liquid slugging at the next startup.

  165. Question 165Commercial Refrigeration

    During an electric defrost cycle on a low-temperature walk-in evaporator, the evaporator fans normally:

    1. stay off during defrost and until the coil cools Correct answer.
    2. run at full speed to circulate the warm air
    3. cycle on and off with the defrost heaters
    4. run in reverse to push heat through the coil

    Explanation

    Fans are stopped during defrost so warm, moisture-laden air is not blown into the box, and they are held off by a fan delay switch until the coil is cold again. Starting them early would refreeze meltwater and raise box temperature.

  166. Question 166Commercial Refrigeration

    Which compressor design compresses refrigerant between a fixed scroll and an orbiting scroll?

    1. Reciprocating
    2. Screw
    3. Scroll Correct answer.
    4. Rotary vane

    Explanation

    A scroll compressor uses two interleaved spiral wraps; one is stationary while the other orbits, trapping and squeezing gas pockets toward the center discharge port. Reciprocating, rotary vane, and screw machines use pistons, sliding vanes, or rotors.

  167. Question 167Commercial Refrigeration

    A medium-temperature display case with a TXV shows 18°F superheat at the evaporator outlet, well above the 6-10°F target. To lower superheat, the technician should:

    1. turn the adjusting stem clockwise to increase spring force
    2. leave it alone because 18°F is normal for a TXV
    3. replace the valve, since a TXV cannot be field adjusted
    4. turn the stem counterclockwise to lower spring force Correct answer.

    Explanation

    Turning the TXV adjusting stem counterclockwise reduces spring pressure on the diaphragm, so the valve feeds more refrigerant and superheat falls. Adjustments should be small, with time allowed for the system to stabilize between changes.

  168. Question 168Commercial Refrigeration

    On an air-cooled condensing unit running in cold weather, a fan-cycling pressure control holds head pressure by:

    1. shutting off condenser fans to hold head pressure up Correct answer.
    2. increasing the evaporator fan speed to raise load
    3. reducing the amount of refrigerant charge in the system
    4. bypassing hot gas directly into the evaporator coil

    Explanation

    A fan cycling control opens and closes the condenser fan circuit based on discharge pressure, cutting heat rejection when ambient is low so head pressure stays high enough for the metering device to feed properly. It is a low-ambient strategy only and has no effect on charge or evaporator airflow.

  169. Question 169Commercial Refrigeration

    The primary function of a liquid receiver in a refrigeration system is to:

    1. separate oil from the hot discharge gas
    2. store liquid refrigerant and seal the liquid line Correct answer.
    3. collect non-condensable gases for later removal
    4. prevent liquid refrigerant from reaching the suction

    Explanation

    The receiver holds the system charge as liquid and provides the liquid seal needed at the expansion valve inlet. Oil separation and suction-side liquid protection are handled by other components.

  170. Question 170Commercial Refrigeration

    A suction line accumulator is installed in a system to:

    1. remove moisture from the refrigerant charge
    2. hold liquid refrigerant for the liquid line
    3. stop liquid from reaching the compressor Correct answer.
    4. lower the discharge pressure at high ambient

    Explanation

    An accumulator is a vessel on the suction line that traps liquid, meters it back as vapor, and protects the compressor from slugging. Moisture removal belongs to the filter-drier, and liquid storage for the liquid line belongs to the receiver.

  171. Question 171Commercial Refrigeration

    A system is evacuated to 500 microns and the pump is valved off; the gauge holds steady at 500 microns for ten minutes. This indicates:

    1. the micron gauge has failed and the test is invalid
    2. a leak that must be located and repaired
    3. moisture is still boiling off inside the system
    4. a tight, dry system with no leaks Correct answer.

    Explanation

    A standing vacuum that holds steady shows the system is leak-free and dry enough to charge. A slow continuous rise toward atmosphere points to a leak, while a rapid rise that then levels off indicates moisture still evaporating.

  172. Question 172Commercial Refrigeration

    An evaporator pressure regulator (EPR) valve is used on a supermarket system to:

    1. hold minimum evaporator pressure on one circuit Correct answer.
    2. terminate defrost at the correct coil temperature
    3. control liquid injection into the compressor
    4. hold condenser pressure constant at all loads

    Explanation

    The EPR throttles suction from one evaporator so its pressure, and therefore its coil temperature, stays at the desired level even when the common suction header is pulled lower. This protects product in cases that need a warmer coil.

  173. Question 173Commercial Refrigeration

    An oil pressure safety switch protects a compressor by:

    1. locking out the compressor if oil pressure is low Correct answer.
    2. cycling the crankcase heater on oil temperature
    3. metering oil back from the condenser coil
    4. keeping oil level correct in the liquid receiver

    Explanation

    The control compares net oil pressure (oil pump pressure minus suction pressure) with a setpoint and, if it is not satisfied within the time delay, locks the compressor out. This prevents bearing damage from oil starvation.

  174. Question 174Commercial Refrigeration

    A condensing unit shows high discharge pressure, high liquid line temperature, and normal superheat. The most likely cause is:

    1. reduced condenser airflow or a dirty coil Correct answer.
    2. a TXV stuck open and flooding the evaporator
    3. an undercharged system with a low liquid level
    4. a light load on the evaporator coil

    Explanation

    Anything that reduces heat rejection, such as a dirty coil, failed fan, or recirculated air, raises condensing temperature and liquid line temperature together. Superheat stays roughly normal because the evaporator side is unaffected.

  175. Question 175Commercial Refrigeration

    A partially blocked liquid line filter-drier will typically produce:

    1. higher than normal suction pressure
    2. higher than normal discharge pressure only
    3. no noticeable change in the system readings
    4. a temperature drop across the drier Correct answer.

    Explanation

    A restriction causes a pressure and temperature drop across the drier, starving the metering device so suction pressure falls and superheat rises. A measurable temperature difference across the drier shell is the classic field check.

  176. Question 176Commercial Refrigeration

    A pump-down cycle controlled by a liquid line solenoid valve is used to:

    1. defrost the evaporator coil between run cycles
    2. purge non-condensable gases from the receiver
    3. raise suction pressure during periods of light load
    4. move refrigerant out of the evaporator on shutdown Correct answer.

    Explanation

    On pump-down the thermostat opens the liquid line solenoid, the compressor keeps running until the low-pressure control trips, and refrigerant is stored in the receiver and condenser. This keeps liquid out of the evaporator and crankcase during the off cycle.

  177. Question 177Commercial Refrigeration

    When charging a system that uses a zeotropic refrigerant blend, the refrigerant should be added:

    1. as a liquid from the cylinder Correct answer.
    2. into the suction line through a manifold gauge set
    3. only after the box reaches its setpoint
    4. as a vapor from the cylinder

    Explanation

    Blends fractionate because their components boil at different temperatures, so vapor charging would shift the mixture and change performance. Charging liquid, usually throttled into the low side, keeps the cylinder composition intact.

  178. Question 178Commercial Refrigeration

    On a compressor equipped with cylinder unloading, when suction pressure falls to the unloader setpoint the mechanism:

    1. closes the discharge service valve to limit capacity
    2. bypasses hot discharge gas into the evaporator
    3. reduces the number of condenser fans running
    4. holds the suction valves open on selected cylinders Correct answer.

    Explanation

    Unloaders hold the suction valve plates open on chosen cylinders, so those cylinders stop compressing gas even though the shaft keeps turning. Capacity steps down to match a falling load and steps back up as suction pressure rises.

  179. Question 179Commercial Refrigeration

    The defrost termination sensor on a walk-in freezer evaporator is best located:

    1. on the fan motor mounting bracket
    2. in the condensate drain pan
    3. on the suction line outside the evaporator housing
    4. at the part of the coil that clears last Correct answer.

    Explanation

    The termination sensor must sample the point that is hardest to clear so defrost ends only after the whole coil is frost-free. Placing it where frost melts early would terminate the cycle with ice still on the coil.

  180. Question 180Commercial Refrigeration

    On a parallel rack, one compressor's sight glass stays low while the others stay full. The most likely cause is:

    1. a restricted oil return line to that compressor Correct answer.
    2. an excessive refrigerant charge in the system
    3. a failed oil separator, which would affect every compressor
    4. a failed crankcase heater on another compressor

    Explanation

    A rack uses one oil separator and reservoir with a level regulator feeding each compressor, so a single low sump points to a problem on that compressor's oil feed. Separator or charge problems would show up across the whole rack.

  181. Question 181Light Commercial Refrigeration

    Evaporator superheat is defined as the difference between which two temperatures?

    1. Suction temperature minus saturated suction temperature Correct answer.
    2. Liquid line temperature minus ambient temperature
    3. Saturated suction temperature minus suction line temperature
    4. Discharge temperature minus condensing temperature

    Explanation

    Superheat is the amount by which refrigerant vapor has risen above its saturation temperature at a given pressure. Measuring suction line temperature and subtracting the saturated suction temperature from a pressure/temperature chart gives evaporator superheat.

  182. Question 182Light Commercial Refrigeration

    Continuous bubbles passing through the liquid line sight glass of a walk-in cooler most directly indicate:

    1. A blocked suction filter drier
    2. An excess refrigerant charge
    3. Air trapped in the condenser
    4. A shortage of liquid refrigerant or a restriction upstream Correct answer.

    Explanation

    Bubbles in the sight glass are flash gas forming because liquid refrigerant is not fully condensed or is being throttled before the glass. Undercharge and a liquid line restriction are the two standard causes to check.

  183. Question 183Light Commercial Refrigeration

    Which box temperature is typical for a walk-in cooler storing fresh produce?

    1. 55 degrees F
    2. 35 degrees F Correct answer.
    3. 0 degrees F
    4. 15 degrees F

    Explanation

    Walk-in coolers are designed to hold product above freezing, generally in the 35 to 38 degrees F range. Holding near 35 degrees F preserves fresh product without freezing it.

  184. Question 184Light Commercial Refrigeration

    Frost buildup on a freezer evaporator coil reduces system capacity mainly because the frost:

    1. Increases refrigerant flow through the coil
    2. Lowers suction pressure so the compressor runs cooler
    3. Insulates the coil surface and blocks airflow Correct answer.
    4. Raises superheat to a safer level

    Explanation

    Ice is a poor conductor of heat, so a frosted coil transfers less heat from the box air to the refrigerant. The frost also narrows the air passages, cutting airflow across the coil and further reducing capacity.

  185. Question 185Light Commercial Refrigeration

    What is the purpose of a crankcase heater on a commercial refrigeration compressor?

    1. Hold the oil at operating temperature during peak load
    2. Boil refrigerant out of the oil that migrated during the off cycle Correct answer.
    3. Maintain head pressure when outdoor air is cold
    4. Prevent condensation from forming in the liquid line

    Explanation

    During shutdown, refrigerant can migrate to the crankcase and be absorbed by the oil. The crankcase heater warms the oil so that refrigerant is driven off and the oil does not become diluted and lose lubricity at startup.

  186. Question 186Light Commercial Refrigeration

    Where should a thermostatic expansion valve sensing bulb be clamped?

    1. On the bottom header of the evaporator coil
    2. On the liquid line near the receiver
    3. On the discharge line near the condenser
    4. On the suction line at the evaporator outlet Correct answer.

    Explanation

    The bulb must sense the temperature of refrigerant leaving the evaporator so the valve can regulate superheat. It is clamped tightly to a clean horizontal section of suction line at the coil outlet and insulated from surrounding air.

  187. Question 187Light Commercial Refrigeration

    A reach-in freezer shows about 2 degrees F superheat at the evaporator outlet, and frost is forming back along the suction line toward the compressor. The most likely cause is:

    1. The expansion valve is overfeeding or the bulb has lost contact Correct answer.
    2. The expansion valve is starving the coil
    3. The system is low on refrigerant charge
    4. The condenser coil is plugged with lint

    Explanation

    Very low superheat means the valve is admitting more liquid than the coil can evaporate, allowing droplets to carry over and frost the suction line. A bulb that has lost good thermal contact with the line will not close the valve, producing the same flooding symptom.

  188. Question 188Light Commercial Refrigeration

    What does the pump-down cycle accomplish in a commercial refrigeration system?

    1. It removes liquid refrigerant from the evaporator before shutdown Correct answer.
    2. It keeps the crankcase heater energized during shutdown
    3. It raises evaporating temperature during light-load periods
    4. It holds head pressure steady in cold ambient conditions

    Explanation

    In a pump-down system, the liquid line solenoid closes and the compressor continues running until the low-pressure control is satisfied. This clears the evaporator and suction line of refrigerant so liquid cannot migrate into the compressor while it is off.

  189. Question 189Light Commercial Refrigeration

    A condenser fan cycling control is used on a remote condenser to:

    1. Hold a minimum head pressure when outdoor air is cold Correct answer.
    2. Bypass hot gas to the evaporator inlet
    3. Modulate the expansion valve to prevent flooding
    4. Cycle the compressor to control box temperature

    Explanation

    In low ambient conditions the condenser can reject too much heat, dropping head pressure below the level needed to feed the expansion valve and cool the compressor. The fan cycling switch shuts fans off as head pressure falls so a minimum pressure is maintained.

  190. Question 190Light Commercial Refrigeration

    In a pump-down system, where is the liquid line solenoid valve normally installed?

    1. In the liquid line just ahead of the expansion valve Correct answer.
    2. In the suction line at the compressor inlet
    3. In the hot gas bypass line to the evaporator
    4. In the discharge line before the condenser

    Explanation

    The solenoid is placed in the liquid line near the evaporator so that closing it stops the flow of liquid into the coil. The compressor then pumps the coil down to the low-pressure switch setting and shuts off.

  191. Question 191Light Commercial Refrigeration

    What is the function of an evaporator pressure regulator in a system serving multiple fixtures at different temperatures?

    1. It maintains a minimum condensing pressure in cold weather
    2. It limits compressor suction pressure during pull-down
    3. It meters liquid refrigerant into the evaporator
    4. It holds a minimum evaporator pressure so the coil stays above freezing Correct answer.

    Explanation

    An EPR is set to keep the evaporator from dropping below a chosen pressure, which corresponds to a temperature above 32 degrees F. This lets a cooler coil operate on a system whose suction pressure is pulled down by a freezer circuit.

  192. Question 192Light Commercial Refrigeration

    A condenser coil that is heavily fouled with lint and dust will typically cause:

    1. Low suction pressure with a clear sight glass
    2. Normal head pressure but higher subcooling
    3. High head pressure and reduced system capacity Correct answer.
    4. Low head pressure and increased capacity

    Explanation

    When airflow through the condenser is blocked, the refrigerant cannot reject heat and condensing temperature and pressure rise. High head pressure raises compression ratio, reduces capacity, and increases compressor current draw.

  193. Question 193Light Commercial Refrigeration

    A defrost termination and fan delay control on a walk-in freezer serves which purpose?

    1. It maintains head pressure during the defrost cycle
    2. It ends defrost on coil temperature and holds fans off until the coil rechills Correct answer.
    3. It closes the liquid line solenoid at the end of defrost
    4. It starts each defrost period at a fixed time each day

    Explanation

    The control terminates defrost when the coil warms to its set temperature, preventing unnecessary heating, and delays the evaporator fans until the coil cools again. Without the delay, the fans would blow warm, moist air into the box and onto the product.

  194. Question 194Light Commercial Refrigeration

    A typical oil pressure safety switch will lock out the compressor after oil pressure fails to build for approximately:

    1. 10 minutes
    2. 15 seconds
    3. 60 minutes
    4. 120 seconds Correct answer.

    Explanation

    The control compares oil pump pressure to suction pressure and starts an internal timer when the differential is too low. If the differential is not established within about 120 seconds, the switch opens the control circuit and locks the compressor out.

  195. Question 195Light Commercial Refrigeration

    During normal operation at design conditions, a liquid receiver that is completely full of liquid indicates:

    1. A normal condition for cold weather operation
    2. A shortage of refrigerant charge
    3. An overcharge of refrigerant Correct answer.
    4. A restriction in the suction line

    Explanation

    The receiver must have a vapor space to allow for changes in load and for pump-down capacity. A receiver that is liquid-full leaves no room for the charge to move and points to too much refrigerant in the system.

  196. Question 196Light Commercial Refrigeration

    A low-pressure control that cycles a cooler compressor on and off very rapidly during normal operation most likely indicates:

    1. A low refrigerant charge or too narrow a control differential Correct answer.
    2. Worn compressor valves
    3. A dirty evaporator coil
    4. A correctly charged system

    Explanation

    Short cycling on the low-pressure control means pressure is crossing the cut-in and cut-out points too quickly. An undercharge causes pressure to fall fast, and a differential set too narrow makes the control respond to small pressure changes.

  197. Question 197Light Commercial Refrigeration

    A crankcase pressure regulator is applied to a low-temperature system mainly to:

    1. De-superheat hot gas during the defrost cycle
    2. Limit suction pressure at the compressor during pull-down and after defrost Correct answer.
    3. Keep the evaporator from dropping below 32 degrees F
    4. Maintain a minimum head pressure in cold weather

    Explanation

    After a defrost or a long off cycle, evaporator pressure can be high enough to overload the compressor motor. The CPR throttles the suction gas reaching the compressor so that crankcase pressure is held within the motor's safe loading range.

  198. Question 198Light Commercial Refrigeration

    How does superheat measured at the compressor normally compare with superheat measured at the evaporator outlet?

    1. It is typically higher because of heat gain through the suction line Correct answer.
    2. It must be identical if the line is properly insulated
    3. It is always lower because refrigerant cools as it travels
    4. It bears no relationship to evaporator superheat

    Explanation

    Suction gas picks up heat from the surrounding space as it travels to the compressor, even through insulated lines. Because superheat is a temperature difference above saturation, this added heat raises the superheat reading at the compressor above the value at the coil outlet.

  199. Question 199Light Commercial Refrigeration

    A system with a properly operating expansion valve shows 30 degrees F subcooling at the condenser outlet, normal superheat, and higher than normal head pressure. The most likely cause is:

    1. An excess refrigerant charge Correct answer.
    2. A refrigerant undercharge
    3. A failed evaporator fan motor
    4. A restriction in the suction line

    Explanation

    Too much refrigerant backs liquid up in the condenser, increasing the subcooled portion and raising head pressure, while the expansion valve still holds superheat near its setting. Undercharge and restrictions produce the opposite pattern, with low subcooling and bubbles in the sight glass.

  200. Question 200Light Commercial Refrigeration

    In a commercial cube ice machine, what initiates the harvest cycle?

    1. The thickness control ends freeze and hot gas warms the evaporator Correct answer.
    2. The water fill valve opens to refill the sump
    3. The high-pressure switch opens to stop the compressor
    4. The bin thermostat opens and stops the compressor

    Explanation

    A thickness probe or thermostat determines when the ice slab is fully formed and ends the freeze cycle. The machine then routes hot discharge gas through the evaporator to warm the surface so the slab releases and slides into the bin.

NATE HVAC flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Superheat definition
The difference between the measured suction-line temperature and the saturated evaporating temperature at the same pressure, showing how far the vapor has risen above saturation.
One ton of refrigeration
A cooling rate equal to 12,000 Btu per hour or 200 Btu per minute, the heat removal needed to freeze one ton of ice in 24 hours.
Ohm's law
Voltage equals current times resistance, written E = I × R. For example, 240 volts across 24 ohms produces 10 amps of current flow.
Nitrogen purge while brazing
A slow flow of dry nitrogen through the tubing during brazing displaces oxygen so carbon and oxide scale cannot form inside the refrigerant circuit.
Target superheat fixed orifice
With a fixed orifice or piston, charge is correct when measured superheat matches the manufacturer chart, commonly 10 to 15°F at design indoor wet bulb and outdoor temperature.
Subcooling TXV target
On a thermostatic expansion valve system, liquid-line subcooling of roughly 8 to 12°F indicates a full liquid column and correct refrigerant charge.
Sensible heat equation
Sensible Btu per hour equals 1.08 times standard airflow in cubic feet per minute times the dry-bulb temperature difference across the coil.
R-410A characteristics
A near-azeotropic blend running roughly 50 to 60 percent higher pressures than R-22, using POE oil, and requiring gauges and hoses rated for its pressure.
Velocity pressure formula
Air velocity in feet per minute equals 4005 times the square root of velocity pressure measured in inches of water column with a pitot tube.
Typical branch duct velocity
Supply branch ducts are usually sized for 400 to 700 feet per minute, while trunk lines run 600 to 900 feet per minute to limit noise and friction.
External static pressure
The sum of supply and return duct pressure drops measured at the air handler, typically limited to about 0.5 inch water column in residential systems.
Clocking the gas meter
Input Btu per hour equals 3600 divided by the seconds for one cubic foot of meter rotation, multiplied by the gas heating value in Btu per cubic foot.
Natural gas manifold pressure
Most natural gas appliances are set near 3.5 inches water column manifold pressure, with about 5 to 7 inches inlet supply pressure while firing.
Temperature rise check
Temperature rise in degrees Fahrenheit equals furnace output Btu per hour divided by 1.08 times blower cfm, and must fall within the nameplate rise range.
Balance point
The outdoor temperature at which heat pump heating capacity exactly equals building heat loss; below that point supplemental or auxiliary heat must make up the difference.
Defrost cycle
A timed or demand-initiated reverse-cycle operation that melts frost from the outdoor coil, typically terminating on coil temperature or a time limit.
Emergency heat mode
A control setting that locks out the compressor and uses only electric resistance or other backup heat, often selected manually after a compressor failure.
Reversing valve operation
On most residential heat pumps the solenoid is energized in heating, routing discharge gas to the indoor coil; it is de-energized for cooling mode.
Nozzle flow versus pressure
Oil nozzle flow varies with the square root of pressure, so a nozzle rated 1.00 gph at 100 psi delivers less than rated flow at a lower pump pressure.
Cad cell resistance
A cadmium sulfide flame sensor reads roughly 400 to 1000 ohms when flame is present; the primary control locks out when resistance climbs above about 1600 ohms.
Number two fuel oil heat content
A gallon of number two heating oil contains about 140,000 Btu, so a 1.00 gph nozzle firing at 100 psi releases roughly 140,000 Btu per hour.
Hydronic gpm formula
Gallons per minute equals Btu per hour divided by 500 times the temperature drop, because one gallon per minute carries 500 Btu per hour per degree.
Boiler relief valve setting
Residential hot water boilers use a pressure relief valve typically set at 30 psi, protecting the boiler and piping from overpressurization and unsafe conditions.
Diaphragm expansion tank precharge
The tank air charge is set to the system cold fill pressure, commonly 12 to 15 psi, and checked before the tank is connected to the loop.
Three-phase power formula
Three-phase watts equal volts times amps times 1.732 times power factor, used to estimate motor input power from measured current and voltage.
Economizer changeover
Rooftop economizers admit outdoor air for free cooling when outdoor enthalpy or dry-bulb temperature falls below the return air condition.
TEV superheat setting
Commercial evaporators using a thermostatic expansion valve are typically set for 4 to 6°F superheat at the coil outlet to fill the coil without floodback.
Refrigerant safety group A2L
A classification for mildly flammable, low-toxicity refrigerants such as R-32 and R-454B, carrying charge limits and ignition-source precautions in the mechanical code.
Suction riser velocity
Vertical suction risers must maintain at least 700 to 1500 feet per minute so entrained oil can be carried back up to the compressor.
Reach-in cooler temperature
Product space in a reach-in cooler is held near 35 to 38°F, with a coil temperature roughly 10 to 12°F colder than the box.
Defrost termination temperature
Electric defrost on a walk-in freezer terminates when the coil sensor reaches about 45 to 55°F, after which fans restart following a delay.
Capillary tube critical charge
Capillary tube systems have no receiver and are charged by weight; adding refrigerant to correct a partial frost pattern usually overcharges the system.

NATE HVAC study guide

Core: Safety, Tools, and Refrigeration/Electrical Fundamentals

Safety, tools, and the fundamentals behind every question

Start with the hazards: lockout/tagout before opening any disconnect, PPE (goggles, gloves, insulated tools), and refrigerant handling under EPA Section 608. Refrigerant vapor is heavier than air and displaces oxygen in pits and basements; liquid refrigerant causes frostbite; never pressurize a system with oxygen or compressed air. Treat a capacitor as live until you have proven it discharged.

Tools to recognize: manifold gauge set (compound low-side gauge, high-side gauge), micron gauge, vacuum pump, clamp meter, multimeter, manometer, and digital thermometers. Common traps include reading a capacitor without discharging it, leaving the manifold center port open during a leak check, measuring vacuum at the pump instead of at the system, and mixing wet-bulb with dry-bulb readings.

Refrigeration basics: the four components (compressor, condenser, metering device, evaporator), the pressure-temperature chart for each refrigerant, superheat at the evaporator outlet, subcooling at the condenser outlet, and the state of the refrigerant through each part of the cycle. Electrical basics: Ohm's law (E = I x R), series versus parallel circuits, 24-volt control circuits, contactors, start and run capacitors, and telling a load from a switch on a wiring diagram.

Worked example: a 24-volt contactor coil measures 24 ohms across its terminals. I = E/R = 24/24 = 1 amp. If that same coil draws 2 amps, its resistance has roughly halved, so the coil is shorted and the control-circuit fuse or transformer is at risk.

Air Conditioning: Charging and Diagnosing the Cooling Cycle

Charging and diagnosing the cooling cycle

You must move fluidly between pressures and temperatures. Convert suction pressure to evaporating saturation temperature and liquid-line pressure to condensing temperature, then compute superheat (suction line temperature minus evaporating temperature) and subcooling (condensing temperature minus liquid line temperature). Fixed-orifice/piston systems are charged by superheat using the indoor wet-bulb and outdoor dry-bulb target chart; TXV systems are charged by subcooling, commonly 8-12°F.

Benchmark numbers: 400 cfm per ton nominal, an 18-22°F indoor split (return dry-bulb minus supply dry-bulb), and a condenser split of roughly 15-25°F above outdoor ambient.

Traps: charging a TXV system by superheat, charging a piston system by subcooling alone, and blaming charge for an airflow problem. Low airflow and low charge both produce low suction pressure and high superheat; airflow problems show a small temperature split, while low charge usually shows a larger split. Overcharge shows high subcooling, high head pressure and high compressor amps. A restriction (kinked line, plugged filter-drier) shows low suction, high superheat, low head pressure and little or no subcooling. Non-condensables raise head pressure with abnormally high subcooling and no other explanation.

Worked example: return air at 75°F and supply air at 58°F gives a 17°F split, which is acceptable. If the split is only 8°F with low suction pressure, inspect the blower, filter and evaporator coil before adding refrigerant.

Air Distribution: Airflow, Static Pressure and Proven Numbers

Airflow, static pressure and the numbers that prove it

Air distribution questions test whether you can prove airflow rather than guess at it. Know total external static pressure (TESP): measure with a manometer using the correct pressure taps, with a clean filter and a wet coil, and compare the result to the blower performance table. Residential equipment is commonly rated at 0.5 in. wc.; a reading above the table rating means the ducts, coil, filter or registers are undersized or restricted.

Know the fan laws: cfm varies directly with speed, static pressure with the square of speed, and horsepower with the cube. Know the friction-rate method (about 0.1 in. wc. per 100 ft of equivalent length), supply velocities of roughly 700-900 fpm, return velocities of 600-700 fpm, and the 400 cfm/ton rule.

Traps: taking static pressure in the return plenum only, reading a blower table without correcting for a wet coil and filter, forgetting that a high-MERV filter or bypass humidifier changes TESP, and confusing face velocity with duct velocity. Also know the sensible heat equation: cfm = sensible Btu/hr ÷ (1.08 x ΔT).

Worked example: a 3-ton system must move about 1,200 cfm. A 16 x 25 in. filter grille has 2.78 ft² of face area, so 1,200 ÷ 2.78 ≈ 432 fpm at the grille, which is acceptable. The same 1,200 cfm forced through a 12 in. round trunk (0.785 ft²) is about 1,528 fpm, far too fast and a guaranteed source of noise and high static pressure.

Gas Heating: Combustion, Pressures and the Safety Chain

Combustion, gas pressure and the safety chain

Gas heat questions center on combustion and the sequence of operation. Know the sequence: call for heat, inducer proves draft through the pressure switch, the ignition source energizes, the gas valve opens, flame proves through the flame sensor, the blower starts on a time/temperature delay, and the high limit protects the heat exchanger. Any failed proof shuts the valve.

Know the pressures: natural gas manifold typically 3.5 in. wc. with about 7 in. wc. supply; LP manifold 10-11 in. wc. with 11-14 in. wc. supply. Measure manifold pressure with the burner firing, using a manometer on the valve outlet tap. A classic trap is reading it with the burner off or with the hose on the inlet side. Temperature rise (return to supply) must fall inside the rating-plate range, commonly 35-65°F.

Other traps: assuming a hot surface igniter is good because it glows (check amp draw and position), ignoring combustion air and venting category, overlooking altitude derating (about 4% per 1,000 ft above 2,000 ft), and misreading CO and CO2 readings.

Worked example (clocking the meter): the dial moves 2 ft³ in 60 seconds with natural gas at 1,000 Btu/ft³. Input = (3,600 ÷ 60) x 2 x 1,000 = 120,000 Btu/hr. Compare that to the rating plate; a large mismatch points to overfiring, wrong orifices or incorrect manifold pressure.

Heat Pump: Reversing the Cycle and Auxiliary Heat

Reversing the cycle

A heat pump adds a reversing valve, so the outdoor coil becomes the evaporator in heating and the indoor coil becomes the condenser. Know which coil is which in each mode, that the suction line is always the line returning to the compressor (measured at the true suction port on the reversing valve), and that the indoor coil rejects heat in the heating mode.

Know the accessories: auxiliary heat (electric strips staged with the compressor), emergency heat (strips only, compressor locked out), balance point (where heat-pump capacity equals building load), and defrost (initiated on time/temperature or demand, terminated by coil temperature or time, with strips energized during defrost to temper supply air).

Traps: checking charge in heating mode without the manufacturer's chart (weigh in, or verify subcooling in cooling mode), condemning a reversing valve when the real fault is the solenoid coil or a valve that needs a pressure differential to shift, confusing auxiliary heat with emergency heat, and forgetting that low indoor airflow in heating raises head pressure and temperature rise.

Worked example: at 30°F outdoor the heat pump delivers 24,000 Btu/hr while the house load is 30,000 Btu/hr. The 6,000 Btu/hr gap must be made up by resistance heat: 6,000 ÷ 3,412 ≈ 1.8 kW, so at least a 2 kW strip bank must stage on, with lockout controls deciding when.

Oil Heating: Nozzles, Pressure and Combustion Testing

Oil burners: nozzles, pressure and combustion testing

Oil heat questions revolve around the burner's hydraulic and electrical parts. Know the sequence: thermostat calls, the primary control starts the burner motor and ignition transformer, the fuel unit builds pressure (typically 100 psi, sometimes 140 psi), the nozzle atomizes oil, the electrodes ignite the spray, and the cad cell proves flame to hold the control in. Without flame proof, the primary locks out on its safety timing.

Know that nozzle ratings are stated in gph at 100 psi, and that flow changes with the square root of pressure, so raising pressure from 100 to 140 psi increases flow about 18%. Know the 140,000 Btu per gallon rule, electrode settings per the manufacturer, and combustion targets: CO2 roughly 11-13%, smoke 0-2 (ideally 0), plus stack temperature and draft per the data plate, often about -0.02 in. wc. overfire.

Traps: sizing a nozzle by eye, overfiring a derated boiler, ignoring a delayed-ignition pattern that soots the chamber, and setting electrodes by guesswork. One-pipe systems with excessive lift, or air in the lines, starve the pump and cause lockouts that look electrical.

Worked example: a 0.85 gph nozzle at 100 psi delivers 0.85 x 140,000 ≈ 119,000 Btu/hr input. If the nameplate calls for 100,000 Btu/hr, the correct nozzle is about 0.70 gph, not a larger nozzle turned down with pump pressure.

Hydronics (Gas and Oil): Pressure, Circulation and Air Control

Water-side heat: pressure, circulation and air control

Hydronic questions test the relationship between pressure, temperature and air. Know the fill pressure: about 1 psi per 2.31 ft of height above the fill point plus 4-5 psi, so a two-story house typically fills cold at around 12 psi. The relief valve is normally 30 psi, the expansion tank precharge matches cold fill pressure, and the pressure-reducing valve maintains it.

Know the components: boiler, aquastat (operating control), high limit, low-water cutoff, circulator, zone valves or zone pumps, air eliminator or scoop, flow-control valve, and primary/secondary piping with closely spaced tees for hydraulic separation. Know that the circulator should pump away from the point of no pressure change, which is the expansion tank connection.

Traps: setting an expansion tank precharge without isolating and draining it, diagnosing a no-heat zone as a bad zone valve when the system is air-bound, ignoring a weeping relief valve caused by a failed tank or overfill, and confusing boiler water temperature with supply water temperature at the zone.

Worked example: a zone must deliver 30,000 Btu/hr at a 20°F design drop. gpm = Btu/hr ÷ (500 x ΔT) = 30,000 ÷ (500 x 20) = 3 gpm. Select the circulator and pipe size for 3 gpm at the calculated head rather than for the boiler's total output.

Light Commercial Air Conditioning: Rooftops, Three-Phase Power, Economizers

Rooftop units, three-phase power and economizers

Light commercial cooling adds scale and controls: packaged rooftop units, split systems with remote condensing units, two-stage or tandem compressors, belt-driven blowers, VAV boxes and economizers. Know three-phase basics: 208/230 V and 460 V systems, line versus control voltage, phase rotation and phase loss, contactors, overloads, and crankcase heaters.

Know economizer operation: on a call for cooling with outdoor air suitable (dry-bulb or enthalpy changeover), the damper opens and the compressor is staged off or modulated. A failed actuator, stuck damper or bad enthalpy control causes frozen coils, high energy use and comfort complaints. Know TESP, belt tension and sheave adjustment, blower performance tables, and the correct airflow for each refrigerant circuit.

Traps: starting a scroll compressor with reversed rotation (low amp draw, no pressure differential, loud noise). Verify phasing before startup. Also, ignoring single-phasing as a cause of compressor failure, diagnosing an economizer as a refrigerant problem, and charging one circuit using the other circuit's readings.

Worked example: a 10-ton rooftop with two circuits, each rated 5 tons, should move about 2,000 cfm per circuit at 400 cfm/ton. If TESP measures 0.9 in. wc. against a 0.5 in. wc. rating, correct the duct or filter restriction first; low airflow on both circuits is a distribution problem, not a charge problem.

Commercial Refrigeration: Low and Medium Temperature Systems

Low and medium temperature systems

Commercial refrigeration runs continuously at low or medium temperature, so controls and accessories differ from comfort cooling. Know the components: condensing unit, receiver, liquid line with filter-drier and sight glass, TEV, evaporator (unit cooler), suction line with accumulator or heat exchanger, and head-pressure controls for low ambient (fan cycling, fan speed, or flooded condenser holding minimum receiver pressure).

Know the pressure regulators: the EPR (evaporator pressure regulator) holds a minimum evaporator pressure so product does not freeze; the CPR holds suction pressure to protect the compressor; the OPR holds receiver pressure. Know defrost types (off-cycle, electric, hot gas, air), defrost termination and fan-delay controls, and the temperature difference (TD) between box air and evaporator, commonly about 10°F for medium temperature and 10-15°F for low temperature.

Traps: charging to a clear sight glass alone, adjusting an EPR without knowing the box design, calling ice on a coil low charge when it is really a defrost failure, and forgetting that a low-temperature compressor needs a crankcase heater and pump-down control.

Worked example: a cooler holding 35°F with a designed 10°F TD needs an evaporator at 25°F. Set the EPR or check the TEV so suction saturation temperature is about 25°F, then verify 4-8°F superheat at the evaporator outlet.

Light Commercial Refrigeration: Walk-ins, Reach-ins and Ice Machines

Walk-ins, reach-ins and ice machines

This domain applies refrigeration fundamentals to equipment you can touch: walk-in coolers and freezers, reach-in cases, prep tables and ice machines. Know the differences. A walk-in freezer needs electric or hot-gas defrost with defrost termination and fan delay; a cooler may use off-cycle defrost; reach-ins often have a condensate evaporator pan; ice machines run a freeze cycle then a harvest cycle initiated by a pressure or thermistor control, using hot gas to release the slab.

Know the service points: unit cooler fan motors and blade clearance, door gaskets and frame heaters, drain lines with traps, defrost timers and their fail-safe position, temperature versus pressure controls, and condenser cleanliness. On ice machines, water quality, inlet screens, curtain/bin switches and head pressure controls matter more than charge.

Traps: overcharging a critically charged reach-in, replacing a thermostat when the defrost timer is stuck in defrost, ignoring a plugged drain trap that floods the box, and diagnosing an ice machine as failed when it is simply in harvest.

Worked example: a walk-in cooler sitting at 40°F with a heavily iced evaporator and timer pins pushed in likely has a defrost termination or timer failure, not a refrigerant shortage. Defrost the coil, confirm termination at roughly 50-60°F coil temperature, and verify the timer advances out of defrost.

NATE HVAC cheat sheet

Quick reference

Core: Safety, Tools, Refrigeration and Electrical Fundamentals

  • Ohm's law: E = I × R; single-phase power P = E × I × power factor; 1 horsepower = 746 watts.

  • One ton of refrigeration = 12,000 Btu/h = 200 Btu/min.

  • Superheat = measured suction-line temperature minus the saturated suction temperature at the same measured pressure.

  • Subcooling = saturated condensing temperature minus the measured liquid-line temperature.

  • At a fixed pressure a pure refrigerant has exactly one saturation temperature; temperature glide appears only with zeotropic blends.

  • Pressure conversions: 1 psi = 2.31 ft of water = 27.7 in. wc; 1 in. wc = 0.036 psi.

  • Brazing requires a slow dry-nitrogen purge through the tubing; never pressure-test with oxygen and never use compressed air on a refrigerant circuit.

  • Discharge and verify capacitors with a resistor before touching terminals; lock out and tag out every power source before opening a panel.

  • Reference constants: 1 Btu raises 1 lb of water 1°F; standard air weighs about 0.075 lb/ft³.

Quick reference

Air Conditioning

  • Nominal sensible airflow is 400 cfm per ton; 350 cfm per ton favors latent removal in humid climates.

  • Sensible Btu/h = 1.08 × cfm × ΔT dry bulb.

  • Latent Btu/h = 0.68 × cfm × Δgrains; total Btu/h = 4.5 × cfm × Δenthalpy.

  • Fixed-orifice charging: match measured superheat to the manufacturer target chart, commonly 10–15°F.

  • TXV charging: set by subcooling, typically 8–12°F measured at the condensing unit.

  • Normal evaporator air temperature drop is 16–22°F; a drop below 14°F points to low airflow or an overcharge.

  • R-410A operates at roughly 50–60% higher pressures than R-22 and uses POE oil, which absorbs moisture rapidly.

  • Weighing in the nameplate charge is the only accurate method on fixed-orifice systems with short line sets.

Quick reference

Air Distribution

  • Standard air density is 0.075 lb/ft³; velocity V (fpm) = 4005 × √VP with VP in inches of water column.

  • Residential duct design commonly uses a friction rate of about 0.1 in. wc per 100 ft of equivalent length.

  • Typical velocities: supply trunk 600–900 fpm, branch 400–700 fpm, return 600–900 fpm.

  • Total external static pressure = supply static + return static, read at the plenum taps with a manometer.

  • A typical residential air handler budget is 0.5 in. wc total external static including filter and coil resistance.

  • Flex duct bends need a centerline radius of at least one duct diameter; limit sag to about ½ in. per foot of run.

  • Seal joints with mastic or UL 181 tape; duct leakage is measured in cfm25 with a duct blaster.

  • Diffuser selection uses throw, drop, and noise criteria; a ceiling diffuser mounted 8–10 ft high throws roughly 10–20 ft.

Quick reference

Gas Heating

  • Heating values: natural gas ≈ 1,030 Btu/ft³; propane vapor ≈ 2,500 Btu/ft³.

  • Clocking the meter: input Btu/h = (3600 ÷ seconds per ft³) × Btu per ft³.

  • Manifold pressure: natural gas 3.5 in. wc; LP 10–11 in. wc. Inlet supply: natural gas 5–7 in. wc; LP 11–13 in. wc.

  • Combustion air: 50 ft³ per 1,000 Btu input in unconfined space; 1 in² free area per 2,000 Btu with two grilles.

  • Temperature rise °F = output Btu/h ÷ (1.08 × cfm); it must land inside the nameplate range, often 35–65°F.

  • Category I appliances vent under negative pressure through metal pipe; Category IV condensing units vent under positive pressure through PVC.

  • Combustion targets: CO air-free below 100 ppm, ambient CO below 9 ppm, O2 roughly 5–9% on natural draft.

  • Hot-surface igniters read about 40–90 ohms cold; a cracked igniter reads open circuit.

  • A standing-pilot thermocouple produces roughly 25–30 mV open circuit and must hold the safety valve open at about 10 mV.

Quick reference

Heat Pump

  • Balance point is the outdoor temperature where heat pump capacity equals building heat loss; below it, auxiliary heat carries the remainder.

  • Auxiliary heat is staged by outdoor thermostat or control logic; emergency heat locks the compressor out entirely.

  • Defrost is initiated by time/temperature or on demand, and terminates on coil temperature near 50–70°F or on a time limit.

  • On most residential units the reversing valve solenoid is energized in heating and de-energized in cooling.

  • Charge a heat pump in cooling mode when outdoor ambient is above 60°F; use subcooling on TXV systems, superheat on fixed orifice.

  • COP = heat output (Btu) ÷ electrical input (Btu); HSPF2 is annual heating Btu divided by annual watt-hours.

  • Suction-line accumulators and crankcase heaters protect the compressor from liquid floodback and off-cycle migration.

  • A heat pump with equal suction and discharge pressures and no temperature split often has a stuck reversing valve or failed compressor valves.

Quick reference

Oil Heating

  • Number 2 heating oil ≈ 140,000 Btu/gal; a 1.00 gph nozzle at 100 psi fires about 140,000 Btu/h.

  • Nozzle flow scales with the square root of pressure: gph₂ = gph₁ × √(psi₂ ÷ psi₁).

  • Standard pump pressure is 100 psi; some retention-head burners specify 140 psi.

  • Typical electrode settings are a ⅛ in. gap, 1/16 in. ahead of and above the nozzle centerline - always follow the burner spec sheet.

  • Cad cell reads 400–1,000 ohms with flame; the primary control locks out above about 1,600 ohms after the trial for flame.

  • Targets: smoke 0 to a trace, overfire draft −0.02 to −0.04 in. wc, CO2 11–13% on retention-head burners.

  • Net stack temperature = gross stack temperature minus room temperature; a high net stack indicates a fouled heat exchanger.

  • Bleed the pump fully and replace the nozzle, oil filter, and pump strainer at every annual service.

  • One-pipe systems require a bypass or two-pipe conversion when tank lift exceeds the pump's rated vacuum capability.

Quick reference

Hydronics (Gas and Oil)

  • 1 gpm carries 500 Btu/h per °F of temperature drop (8.33 lb/gal × 60 min × 1 Btu/lb·°F).

  • gpm = Btu/h ÷ (500 × ΔT); a 100,000 Btu/h load at 20°F ΔT needs 10 gpm.

  • Residential boiler aquastat: 180°F operating with a 200°F high limit; relief valve typically set at 30 psi.

  • Cold fill pressure = 12 psi for one to two stories, plus 0.433 psi per foot of height above the boiler.

  • Diaphragm expansion tank air precharge equals the cold fill pressure and is checked with the system at zero pressure.

  • Finned-tube baseboard delivers roughly 550–600 Btu/h per linear foot at 180°F average water and 65°F room air.

  • Primary/secondary piping uses closely spaced tees no more than four pipe diameters apart to decouple the loops.

  • Air removal needs a scoop or separator on the boiler supply plus an automatic vent at the system high point.

  • Steam systems run below 1 psi; 1 psi of pressure lifts water about 28 in. up a riser.

Quick reference

Light Commercial Air Conditioning

  • Three-phase power: watts = volts × amps × 1.732 × power factor.

  • Reverse any two line leads to correct a three-phase compressor or blower spinning backward.

  • Economizers change over at 55–65°F dry bulb or on an enthalpy setpoint; verify minimum position and damper linkage.

  • Crankcase heaters must be energized 8–24 hours before compressor start to drive liquid out of the oil.

  • Belt drives: sheave alignment within 1/32 in. and about ½ in. belt deflection at mid-span for rated tension.

  • Cooling below roughly 55°F outdoor ambient requires fan cycling, head pressure control, or a low-ambient kit.

  • Condensate trap depth must equal 1 in. per inch of negative cabinet static plus 1 in. of reserve.

  • Rooftop units need a curb gasket, accessible filters, and a return-duct smoke detector where code requires it.

Quick reference

Commercial Refrigeration

  • TEV superheat at the evaporator outlet is typically 4–6°F; compressor superheat runs 20–40°F.

  • Evaporator TD (box temperature minus coil temperature) is 10–12°F for coolers and about 10°F for freezers.

  • Suction risers need 700–1,500 fpm to return oil; use double risers when load falls below minimum velocity.

  • Pump-down closes the liquid-line solenoid and pulls the low side to the low-pressure control setting before the compressor stops.

  • Head pressure controls - fan cycling, flooding valves, VFDs - maintain minimum condensing pressure in low ambient.

  • Safety groups: A1 low toxicity and no flame propagation; A2L low toxicity and mildly flammable; B1 higher toxicity.

  • With zeotropic blends, evaluate superheat at the dew point and subcooling at the bubble point because of glide.

  • Ammonia (R-717) is B2L: highly efficient but toxic, requiring detection and relief venting to atmosphere.

  • Liquid-line subcooling at the TEV inlet should be 5–15°F; flash gas causes low capacity and valve hunting.

Quick reference

Light Commercial Refrigeration

  • Reach-in cooler product space 35–38°F; freezers −10 to 0°F, with box temperature set by cold-control differential.

  • Capillary-tube systems are critically charged: charge by weight only and never add refrigerant to fix a partial frost pattern.

  • Freezer defrost terminates near 45–55°F coil temperature, then a fan delay holds fans off until the coil re-chills.

  • Anti-sweat and frame heaters add sensible load; verify their operation before condemning the refrigeration circuit.

  • On a receiver system the sight glass should be clear; bubbles indicate a shortage or flash gas, not always low charge.

  • Test door gaskets with a dollar-bill or tear test; a torn gasket causes frame frost and ice buildup.

  • Evaporator-outlet superheat on a reach-in is typically 6–10°F.

  • Ice machine low production is most often a dirty condenser or a restricted water filter, not a refrigerant fault.

NATE HVAC key terms

Superheat

The number of degrees a refrigerant vapor is above its saturation temperature at a given pressure. Measured at the evaporator outlet, it shows whether the metering device is feeding the coil correctly.

Related: TXV, Subcooling
Subcooling

The number of degrees a liquid refrigerant is below its saturation temperature at a given pressure. Measured at the condenser outlet, it indicates how much liquid is stacked in the condenser.

Related: Superheat, Head pressure control
Refrigerant

A fluid that absorbs heat by boiling at low pressure in the evaporator and releases it by condensing at high pressure in the condenser, moving heat from one place to another inside a sealed circuit.

Related: Superheat, Recovery cylinder
Multimeter

A handheld test instrument that measures voltage, resistance and often current. Technicians use it to verify power supply, check switch continuity and confirm a component's electrical condition before replacing it.

Related: Capacitor, Lockout/Tagout
Lockout/Tagout

A safety procedure in which a disconnect or valve is locked in the off position and tagged so equipment cannot be energized or pressurized while someone is servicing it.

Related: Multimeter
Micron gauge

A digital instrument that reads very deep vacuum in microns. It is used during evacuation to confirm that air and moisture have been removed from a refrigeration circuit before charging.

Related: Recovery cylinder
Capacitor

A component that stores and releases electrical energy to start or run a motor. A weak run capacitor causes high amp draw, slow starting and overheating of compressor or fan motors.

Related: Multimeter
Recovery cylinder

A DOT-approved container used to hold refrigerant removed from a system. It must never be filled above 80 percent liquid full and must be labeled with the refrigerant it contains.

Related: Refrigerant, Micron gauge
Sensible heat

Heat that changes the temperature of a substance without changing its state. In cooling, removing sensible heat lowers the dry-bulb temperature of the room air.

Related: Latent heat, Delta T
Latent heat

Heat that changes the state of a substance without changing its temperature, such as the energy absorbed when water evaporates or released when refrigerant vapor condenses.

Related: Sensible heat, Condensate trap
Delta T

The temperature difference between air entering and leaving a coil, or between supply and return air. It is a quick field check of airflow and equipment performance.

Related: Sensible heat, Static pressure
Condensate trap

A U-shaped trap in the drain line that holds water to block air from being pulled through the drain, while still allowing condensate to flow away from the coil.

Related: Latent heat
Static pressure

The outward pressure a blower creates against the duct system, measured in inches of water column. Excessively high external static pressure signals restricted airflow.

Related: Airflow CFM, Delta T
Airflow CFM

Cubic feet per minute of air moving through a system. Correct airflow is required for proper heat transfer and is estimated from blower charts or measured with a flow hood.

Related: Static pressure
Plenum

A box or chamber attached to the supply or return side of air-handling equipment that feeds several branch ducts. Supply plenums are pressurized; return plenums run under negative pressure.

Related: Static pressure
Manifold pressure

The gas pressure measured at the burner manifold with a manometer. It must match the data plate value so the burners fire at the intended input rate.

Related: Thermocouple, Draft
Thermocouple

A safety device made of two dissimilar metals that generates a small millivolt signal when heated, holding the gas valve open only while the pilot flame is proven.

Related: Manifold pressure
Draft

The movement of combustion gases up a vent or chimney, caused by the natural rise of hot gas or by an induced fan. Proper draft carries flue products outdoors and prevents spillage into the space.

Related: Manifold pressure
Reversing valve

A four-way solenoid valve in a heat pump that switches refrigerant flow direction, swapping the jobs of the indoor and outdoor coils between heating and cooling.

Related: Defrost cycle, Balance point
Defrost cycle

A timed or demand-initiated mode in which a heat pump temporarily reverses to melt frost from the outdoor coil, usually stopping the outdoor fan and bringing on indoor supplemental heat.

Related: Reversing valve, Auxiliary heat
Balance point

The outdoor temperature at which a heat pump's heating capacity exactly equals the building's heat loss. Below that point the system needs supplementary heat to keep the space warm.

Related: Auxiliary heat, Reversing valve
Auxiliary heat

Supplemental electric resistance or fossil-fuel heat that energizes when the heat pump alone cannot meet the load, during defrost, or when the thermostat is set several degrees higher.

Related: Balance point, Defrost cycle
Oil nozzle

A precision orifice that meters and atomizes fuel oil into the combustion chamber. Its size and spray pattern must match the burner firing rate and the shape of the chamber.

Related: Cad cell
Cad cell

A light-sensitive resistor in an oil burner that drops sharply in resistance when it sees flame, proving combustion to the primary control and shutting off oil if flame is lost.

Related: Oil nozzle
Circulator

A pump that moves hot water from the boiler through the piping to the terminal units and back. Circulators are selected by required flow rate and pump head.

Related: Expansion tank, Aquastat
Expansion tank

An air-cushioned tank connected to a hydronic system that absorbs the volume increase as water heats, keeping system pressure stable and preventing relief valve discharge.

Related: Circulator, Aquastat
Aquastat

A temperature-sensing control on a boiler that cycles the burner or circulator to hold a set water temperature, and often includes a high-limit safety function.

Related: Circulator
Economizer

A rooftop unit feature that uses outdoor air for free cooling when conditions are suitable, modulating dampers open and closing them again when outdoor air is too warm or humid.

Related: VAV box
VAV box

A terminal unit with a modulating damper that varies the volume of cool air delivered to a zone in response to thermostat demand, letting one air handler serve many zones.

Related: Economizer, Static pressure
EPR valve

An evaporator pressure regulator that holds a minimum evaporator pressure, and therefore a minimum coil temperature, protecting product in one circuit while other circuits run colder.

Related: Defrost termination, Head pressure control
Head pressure control

A control that keeps condenser pressure high enough for the metering device to work in cold weather, often by cycling the condenser fan or holding refrigerant back in the receiver.

Related: Subcooling, EPR valve
Defrost termination

A control that ends the defrost cycle once the evaporator reaches a set temperature, or after a maximum time limit, so heating does not continue longer than needed.

Related: EPR valve, Defrost cycle
TXV

A thermostatic expansion valve that modulates refrigerant flow into the evaporator in response to the temperature and pressure at the coil outlet, maintaining a set superheat.

Related: Superheat, Subcooling
Walk-in cooler

A large refrigerated room for storing perishable product, typically built from insulated panels and served by an outboard condensing unit and a matched evaporator with defrost control.

Related: Defrost termination, TXV

NATE HVAC study plan

8 weeks · About 6 hours per week

Week 1

Core (safety, tools, basic refrigeration and electrical fundamentals)

  • State, in writing, the lockout/tagout and PPE sequence for a residential service call, and name the conditions that require immediate shutdown (gas odor, CO alarm, scorched wiring, refrigerant release in a confined space).

  • Reproduce the vapor-compression cycle from memory, labeling compressor, condenser, metering device, and evaporator, and give the pressure/temperature state at all four points.

  • Solve 20 Ohm's-law and power-formula problems (E=IR, P=IE) plus five series and five parallel resistance combinations with no reference sheet.

  • Demonstrate on your own meter how to read AC/DC voltage, current, resistance, and capacitance, and explain what each reading proves about the circuit.

  • Identify the hand tools and instruments used for refrigerant recovery, evacuation, brazing, and combustion testing, and state one safety rule for each.

Your checkpoint

A one-page reference card (cycle diagram, formula triangle, shutdown checklist) plus a score of 80% or better on a self-written 40-question Core quiz.

Week 2

Air Conditioning & Core (safety, tools, basic refrigeration and electrical fundamentals)

  • Measure and calculate superheat and subcooling on a running system, then decide whether the charge is correct, over, or under.

  • Trace refrigerant flow through a split system and match each component to its failure symptoms for a no-cool complaint.

  • Read a pressure-temperature chart for R-410A and R-22 and convert gauge pressure to saturation temperature without error on 10 practice points.

  • Diagnose 10 written fault scenarios (restriction, undercharge, dirty condenser, weak capacitor, seized compressor, failed contactor) using only gauge, amp, and temperature evidence.

  • Test a run capacitor and a compressor winding set with a meter and state the pass/fail criteria for each.

Your checkpoint

A completed 20-row troubleshooting matrix (symptom to gauge/amp evidence to probable cause) plus five worked superheat/subcooling calculations with your reasoning shown.

Week 3

Air Distribution & Air Conditioning

  • Measure total external static pressure on a running air handler and compare it to the equipment rating plate limit.

  • Calculate airflow from both temperature rise and velocity-times-area, and reconcile any difference greater than 10%.

  • Plot a duct run with a duct calculator, marking equivalent length for every fitting, and flag the two highest-resistance segments.

  • Balance a two-branch supply system by adjusting dampers until each branch is within 10% of design airflow.

  • Explain how return-air restrictions, filter loading, and bypass affect delivered capacity, and show the effect on a measured temperature split.

Your checkpoint

An annotated supply-and-return layout sketch listing static pressure readings, target and measured CFM for every branch, and the damper adjustments you made.

Week 4

Gas Heating

  • Verify combustion air and venting for a Category I appliance against the installation instructions, and document the two most common venting violations.

  • Measure manifold gas pressure with a manometer and clock the gas meter to compute actual input rate in Btu/h, then compare to the rating plate.

  • Interpret a flue-gas analyzer readout and convert it into steady-state efficiency, CO air-free, and excess air, stating pass/fail thresholds.

  • Sequence both a standing-pilot and a hot-surface-ignition furnace step by step, naming each safety device that must prove before the next step and the failure symptom if it does not.

  • Trace a 24-volt control circuit on a schematic and locate the five points where a no-heat call is most likely to break.

Your checkpoint

A full 50-question mixed practice exam covering Core, Air Conditioning, Air Distribution, and Gas Heating at 75% or better, plus a one-page combustion-analysis worksheet from a single furnace.

Week 5

Heat Pump & Gas Heating

  • Explain the defrost cycle and measure the initiating and terminating conditions, stating the sensor and board inputs that drive each.

  • Diagnose reversing-valve, defrost-board, and auxiliary-heat failures from a described symptom set, naming the confirming measurement for each.

  • Compare the charging method used in heating mode (weigh-in or approach) with the method used in cooling mode, and state why subcooling alone can mislead.

  • Compute the balance point and economic balance point from a capacity table and a heating-load estimate, and explain what the numbers tell a homeowner.

  • List the airflow and refrigerant-charge differences that make a heat pump install fail a commissioning check.

Your checkpoint

A two-sided heat pump service checklist (cooling-mode steps on one side, heating/defrost steps on the other) with the confirming measurement for each step.

Week 6

Oil Heating & Hydronics (Gas and Oil)

  • Set up an oil burner end to end: electrode gap and position, nozzle selection, pump pressure, and a combustion test targeting a smoke number of 0 to 1 with acceptable CO2.

  • Trace oil from tank to nozzle and diagnose a no-heat call across the pump, filter, nozzle, transformer, and primary control.

  • Calculate flow rate, head, and temperature drop for a hydronic loop and select a circulator that meets the requirement.

  • Set boiler aquastats, high limit, and low-water cutoff, and explain what each control protects and how to prove it works.

  • Purge air from a hydronic loop and identify the three symptoms of a system still carrying air or a fouled circulator.

Your checkpoint

A completed oil-burner setup and combustion record for one appliance plus a hydronic loop calculation sheet with circulator selection and control settings.

Week 7

Light Commercial Air Conditioning & Commercial Refrigeration

  • Distinguish light commercial rooftop units from residential split systems across voltage, control, economizer, and ventilation requirements, and list the extra checks a commissioning visit adds.

  • Set up and test an economizer for changeover, minimum position, and enthalpy control, and identify the two most common economizer failure modes.

  • Sequence the refrigeration cycle of a medium-temperature commercial system and identify the function and failure symptoms of the receiver, liquid-line drier, sight glass, and head-pressure control.

  • Check superheat at the evaporator and subcooling at the condenser on a commercial system and determine whether the TXV or the charge is at fault.

  • Explain pump-down, defrost termination, and low-ambient control strategies and state which systems require each.

Your checkpoint

A written comparison table of light commercial AC versus commercial refrigeration service procedures, plus a scored 40-question practice block on Domains 8 and 9.

Week 8

Light Commercial Refrigeration & Core (safety, tools, basic refrigeration and electrical fundamentals) & Air Conditioning & Air Distribution & Gas Heating & Heat Pump & Oil Heating & Hydronics (Gas and Oil) & Light Commercial Air Conditioning & Commercial Refrigeration

  • Cover the light commercial refrigeration objectives: walk-in and reach-in box loading, evaporator superheat, defrost scheduling, and product-temperature verification.

  • Complete two timed 100-question practice exams that mix all ten domains and log every missed question with its cause (knowledge gap, misread, or math error).

  • Re-drill only the missed-question topics until each is answered correctly twice in a row.

  • Recite the safety shutdown criteria, the superheat/subcooling decision rules, and the combustion-test targets from memory without notes.

Your checkpoint

Two timed practice exams scored at 80% or better with a completed error log showing the second-attempt correction for every missed item.

Milestones

Week 2: Score 80% or better on a 40-question Core plus Air Conditioning block, and correctly compute superheat and subcooling on five consecutive practice scenarios.

Week 4: Score 75% or better on a 50-question mixed exam covering Domains 1 through 4, with no more than two misses in the safety and electrical categories.

Week 6: Score 75% or better on a 40-question block covering Heat Pump, Oil Heating, and Hydronics, and complete a combustion record and a hydronic calculation sheet unaided.

Week 8: Score 80% or better on two timed 100-question full-domain exams, with an error log showing every missed item corrected on the second attempt.

NATE HVAC exam day

Your checklist

Government-issued photo ID

Bring a current, unexpired ID with your name matching your registration exactly. If your name differs (nickname, maiden name), resolve it with the provider before test day rather than at check-in.

Appointment confirmation and candidate/eligibility number

Print or save the scheduling email showing your test date, time, location, and the exam(s) you are registered for (Core plus your specialty). Confirm whether your provider requires a printed copy - policies differ.

Confirmed test center address, parking, and route

Do a map check the day before and identify parking or transit options. Many testing centers sit inside office parks or strip centers and are hard to spot; note the suite number and any building-access instructions.

Arrival time buffer

Plan to arrive well before your appointment - commonly 30 minutes, but confirm the exact check-in window with your testing provider. Late arrivals can be refused entry and forfeit the fee.

Written list of which exams you are taking

NATE candidates typically sit a Core exam plus one specialty (e.g., air conditioning, air distribution, gas heating, heat pump). Know your specialty so you are not surprised by the content at the workstation.

Plan for personal items (phone, watch, keys, wallet)

Most centers prohibit phones, smartwatches, notes, and bags in the testing room and provide a locker. Confirm the specific policy - including whether a locker is available - with the provider, and leave anything unnecessary at home or in the vehicle.

Nothing written or printed in the testing room

Do not bring your own notes, formula sheets, or scratch paper. Ask the provider in advance what scratch material (if any) is supplied at the workstation and whether a calculator is provided on screen or must be requested.

Eyewear plan

If you wear contacts, bring glasses and a case in case the room is dry or the center restricts taking items to the restroom. Keep solutions and cases in your locker.

Layer-friendly clothing

Testing rooms are often cold. A light removable layer helps; avoid clothing with large pockets, hoods, or logos that may trigger a security check.

Light snack and water for after the exam

Leave these in the car or locker - they generally cannot go into the testing room. Confirm break and access policies with the provider.

Reviewed the official NATE candidate handbook and content outline

Read the current handbook for question format, time limits, scoring, retake rules, and the knowledge areas covered by your specialty. Do not rely on secondhand summaries.

Confirmed any accommodations in advance

If you need extra time, a separate room, or other accommodation, it must typically be requested and approved before test day. Contact the provider early - this cannot usually be arranged at check-in.

Plan the day

72 hours out

Stop learning new material. Re-read the NATE content outline for your specialty and do a light pass over your weakest two or three domains - safety, electrical fundamentals, refrigerant cycle and charging, airflow, combustion analysis, or whatever your outline emphasizes. Confirm your appointment details and the test center address in writing.

72 hours out

Resolve logistics now: transportation, time off work, childcare, parking cost, and what you will do with your phone and keys. Logistical stress on test morning costs points.

48 hours out

Do one timed practice set to calibrate your pace per question. Note whether you finish early or run out of time, and decide your personal time checkpoint (for example, where you should be at the halfway mark).

24 hours out

Pack your ID, confirmation, and written exam list in one place. Lay out clothing. Confirm the check-in window with the provider and re-check the route for construction or transit changes.

24 hours out

Stop studying by early evening. Eat a normal meal, avoid heavy alcohol, and go to bed at your usual time. Cramming field-service material at midnight reliably hurts recall more than it helps.

Morning of

Eat a real breakfast with protein and caffeine in your normal amount - do not experiment with extra energy drinks. Leave earlier than the map says. Aim to be in the parking lot with time to spare, not pulling in at your appointment time.

At check-in

Present your ID, complete any signature or palm-vein/photo check the center requires, store personal items in the locker, and ask the proctor what scratch material and calculator options exist before you start the clock.

First minutes of the test

Read the on-screen instructions and note the total question count and time limit. Set your personal pace checkpoint. If the interface offers a tutorial, take it - it is usually untimed.

During the test

Answer every question. Work in order, but do not burn several minutes on any single item: make your best call, flag it if flagging is available, and move on. Match units and read the last line of the question first - many items turn on whether they ask for superheat, subcooling, delta-T, or a diagnosis.

Final minutes

Use any remaining time to revisit flagged items and confirm nothing is left blank. Change an answer only when you can point to a specific reason the original was wrong.

After submitting

Most providers show a preliminary pass/fail on screen and issue a printed or emailed score report. Keep that report - you may need it for employer reimbursement or a retake. Confirm with the provider when official results and credentials are issued.

Rules to check

  • Bring valid government-issued photo ID. The name must match your registration; without acceptable ID you will generally be turned away and lose your fee. If your ID name does not match, contact the provider before test day.

  • Arrive within the provider's stated check-in window. Centers commonly ask for arrival 30 minutes early, and late arrivals can be denied entry - confirm the exact window for your appointment rather than assuming.

  • Leave phones, smartwatches, notes, and study material out of the testing room. Expect a secure locker or a requirement to leave items in your vehicle; confirm the specifics with the provider.

  • No notes, books, or personal scratch paper in the testing room. Use only the scratch material the center provides, and ask before the exam starts whether a calculator is available on screen.

  • Do not communicate with other candidates during the exam, and do not attempt to record or transmit question content. Testing agreements typically prohibit reproducing exam items, and violations can void your score and your eligibility.

  • Breaks are usually limited and may not stop the clock. Confirm your provider's break policy before you sit down and plan hydration accordingly; an unscheduled break can cost you time.

  • Scores are reported as pass/fail against a passing standard set by the certifying body, not as a simple percentage of items correct. Do not assume a specific cutoff - get the current passing standard and retake policy from NATE or your provider.

  • If you must reschedule or cancel, do so within the provider's notice window to avoid forfeiting the fee. Confirm the deadline, any reschedule fee, and the retake waiting period with the provider in advance.

  • If equipment or the testing environment fails mid-exam, stop and notify the proctor immediately. Do not continue troubleshooting on your own - an incident report is usually required to preserve your options.

NATE HVAC FAQ

How many NATE HVAC practice questions are available?

The practice set has 200 NATE HVAC questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many NATE HVAC flashcards are available?

The flashcard set has 32 NATE HVAC cards. Each card shows the term and its definition.

Which topics does the NATE HVAC study material cover?

The NATE HVAC study material has 10 sections, including Core: Safety, Tools, and Refrigeration/Electrical Fundamentals, Air Conditioning: Charging and Diagnosing the Cooling Cycle, and Air Distribution: Airflow, Static Pressure and Proven Numbers.

What format facts does the catalog list for the NATE HVAC exam?

The catalog lists these item types: multiple choice for the NATE HVAC exam.