Journeyman Plumber overview

  • 199 practice questions
  • 32 flashcards
  • 8 study guide topics
  • 38 key terms

What you'll study

  • Plumbing Code and Regulations15%
  • Drainage, Waste, and Vent Systems20%
  • Water Supply and Distribution15%
  • Plumbing Fixtures and Appliances12%
  • Water Heaters8%
  • Fuel Gas Piping and Venting10%
  • Safety, Tools, and Jobsite Practices8%
  • Plan Reading, Math, and System Layout12%

The Journeyman Plumber credential is the working-level license that lets a plumber install, alter, and repair plumbing systems without the direct supervision required of an apprentice. It sits between apprenticeship and master licensure: you need documented field hours and a passing exam score to earn it, and it is what most employers mean when they advertise for a licensed plumber. Candidates are typically apprentices finishing their training, maintenance techs formalizing on-the-job experience, or installers moving from a related trade into regulated plumbing work.

The exam tests both code knowledge and practical judgment. Expect heavy coverage of drainage, waste, and vent systems, followed by water supply and distribution, then plumbing code and regulations, fixtures and appliances, plan reading and layout math, fuel gas piping and venting, water heaters, and jobsite safety and tools. Questions are multiple choice and commonly include code-lookup items, sizing calculations, and scenario questions asking what is wrong with an installation.

Preparation matters more than memorization. Work through the applicable plumbing code book until you can navigate it quickly, since many questions are written so a confident reader can verify the answer rather than recall it cold. Pair code study with hands-on review of fittings, venting arrangements, and pipe sizing, then take practice tests that mix all domains the way the real exam does. Licensing requirements, exam scheduling, and current administrative figures are set by your state or local authority, so confirm details on its official site.

Common mistakes

You answer code questions from what your crew does in the field instead of finding the rule in the adopted code book, and you never check which model code edition and local amendments govern the exam.

Field habit is usually 'close enough' and code-compliant only by coincidence; local amendments often change the specific number the question is testing. Study guides from other jurisdictions teach the wrong values.

What to do instead

Confirm the adopted code edition and local amendments on day one. Tab the chapters and index before practising. For every practice question, look the answer up in the actual code text and write the section number next to it, so recall is tied to a citation rather than a habit.

You size a vent using the drainage fixture-unit table (the one used for branch drains, stacks, and building drains) rather than the vent-sizing table.

The two tables sit near each other, both use fixture units and developed length, and both look like 'pick the column, read the pipe size'. Candidates recognise the format and grab the wrong table.

What to do instead

Practise stating out loud which table you are in before you read a single number: drains are sized from drainage fixture units; vents are sized from fixture units served plus developed length and stack height. Remember the guardrails that catch errors: a vent never gets smaller than the drain it serves and never smaller than the minimum vent size (1-1/4 in. under most codes).

You pass a fixture trap that is too far from its vent, or you skip the trap-seal depth check entirely, because the fixture 'drains fine'.

The trap-arm limit is a developed-length rule that changes with trap size and slope, so it is not intuitive; a long trap arm still drains well in practice and only shows up as gurgling or sewer gas later. Candidates also confuse the minimum and maximum trap-seal depths.

What to do instead

Memorise the trap-arm limit table by trap size and slope, and always measure on the drawing as developed length from the trap weir to the vent fitting, not straight-line distance. Drill the trap-seal depth limits (minimum and maximum) so you can state both without hesitating.

You check fixture pressure using only the static pressure at the meter and never subtract the elevation loss to an upper floor or through a below-grade run.

Static pressure at the service looks adequate, so the arithmetic seems finished. The 0.433 psi-per-foot of elevation change is easy to forget because it never appears on a fixture schedule.

What to do instead

Build the habit of writing a pressure budget for every pressure question: starting pressure, minus elevation change (about 0.433 psi per foot of rise), minus friction and device losses, equals pressure at the fixture. Do a handful of drill problems converting head in feet to psi and back until it is automatic.

You size a water supply line from the tape-measure length of the run and omit the equivalent length added by fittings, valves, and meters.

Developed length is invisible; the fittings add up quickly on a run with many elbows, and the sizing tables use developed length, not pipe length. Candidates also forget that the table is selected by the longest run, not the run to the fixture being asked about.

What to do instead

When working a sizing problem, always tabulate: measured pipe length, plus equivalent length for each fitting and device from the table, equals developed length. Then pick the table column for the longest developed length in the system, not the branch you are standing on.

You mix fixture-unit values with trap and drain sizes from memory, so a water closet, urinal, or lavatory ends up with the wrong fixture-unit count, the wrong trap size, or a drain smaller than its trap.

Fixture-unit values, minimum trap sizes, and minimum drain sizes are three separate columns that all describe the same fixture, and exam questions deliberately swap them. Field experience with one or two fixture types creates false confidence.

What to do instead

Make a one-page fixture card from the code tables for the fixtures the exam names (water closet, lavatory, bathtub/shower, kitchen sink, urinal, floor drain, washing machine, dishwasher) listing fixture units, trap size, and minimum drain size side by side. Redraw it from memory weekly until the three columns stop blurring together.

You describe the water heater temperature-and-pressure relief valve discharge pipe incorrectly: reduced in size, threaded or capped at the end, trapped, run uphill, or terminating too high above the floor or outside.

The discharge pipe is rarely installed in a textbook way on service work, so candidates recall a messy real installation instead of the rule. It is also one of the most heavily tested single items in the water heater domain.

What to do instead

Learn the discharge requirements as one short checklist and recite it before every water heater question: full size of the valve outlet, gravity flow with no traps, no reducing fittings or threads at the discharge end, material rated for the temperature, and termination within the required distance of the floor or outside. Practise spotting the single wrong element in a written scenario.

You size gas piping without converting appliance input in BTU/hr to cubic feet per hour, or you use the wrong length column and skip the difference between the longest-length method and the branch-length method.

The sizing tables are in cubic feet per hour, but every appliance label and exam question gives BTU/hr, so a missed conversion throws the whole answer off. The two sizing methods also produce different answers for the same system, and candidates grab whichever table they saw last.

What to do instead

Always write the conversion first: cubic feet per hour equals appliance input BTU/hr divided by the gas heating value (about 1,000 BTU per cubic foot for natural gas; use the value the question supplies for other gases). Then decide and state which method you are using before opening a table, and add the appropriate allowance for other appliances on the same run.

You treat the safety, tools, and jobsite practices items as common sense and never memorise the specific numbers, so you miss questions on ladder setup, confined-space entry thresholds, hot-work precautions, and test requirements.

These questions read as 'obvious' so they get skipped during study, but they are graded on exact figures and procedures, not on general caution. Candidates also answer with what is convenient on a small job rather than the required procedure.

What to do instead

Build a short numbers sheet for this domain (ladder pitch and extension above the landing, air-monitoring thresholds before confined-space entry, fire watch and hot-work rules, pressure-test values and durations for piping systems) and quiz yourself on the figures, not the concepts. For each scenario question, ask what the written procedure requires, not what a two-person crew would actually do.

You convert slope and fall incorrectly, mixing inches per foot with percent grade, or you calculate fall along the horizontal run when the pipe is laid at an angle or when the run length is given in feet and inches.

Plumbing slope is quoted in inches per foot, drawings often give percent, and the two are close enough at small values that an error looks plausible. Arithmetic slips also creep in when run lengths are given as feet plus inches.

What to do instead

Fix two anchors in memory (1/4 in. per foot is about 2 percent; 1/8 in. per foot is about 1 percent) and convert everything to inches before multiplying. For every fall problem, write the equation, convert the run to a single unit, multiply by the slope in inches per foot, and sanity-check the answer against the anchors before moving on.

You read the question as 'what is typical' instead of 'what is the minimum or maximum permitted', and you stop at the main rule without reading the exceptions or the second half of the question.

Exam stems are short and the qualifying word (minimum, maximum, shall not, except) is easy to skim past, especially under time pressure. Exceptions in the code are frequently the whole point of the question.

What to do instead

Adopt a fixed reading routine: underline the qualifying word and the unit before looking at the answer choices, then check whether the cited code section has an exception that applies. When you finish a practice set, review only the questions you missed for misread stems, and count how many were reading errors rather than knowledge gaps.

Exam requirements can change. Confirm current details with the exam provider.

Journeyman Plumber practice

199 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Plumbing Code and Regulations

    What is the minimum water seal depth required for a plumbing trap?

    1. 2 inches Correct answer.
    2. 1 inch
    3. 6 inches
    4. 4 inches

    Explanation

    A plumbing trap must maintain a water seal of at least 2 inches and no more than 4 inches. The minimum prevents sewer gas passage, while the maximum prevents excessive seal that could be difficult to maintain.

  2. Question 2Plumbing Code and Regulations

    What is the minimum slope for a 3-inch horizontal drainage pipe?

    1. 1/16 inch per foot
    2. 1/2 inch per foot
    3. 1/4 inch per foot
    4. 1/8 inch per foot Correct answer.

    Explanation

    Horizontal drainage pipe 3 inches and larger may be installed at a minimum slope of 1/8 inch per foot, which is about 1 percent. Smaller pipe, such as 2-inch and below, generally requires 1/4 inch per foot.

  3. Question 3Plumbing Code and Regulations

    What is the minimum air gap for a water-supply outlet discharging into a fixture?

    1. 1 inch or twice the diameter of the effective opening, whichever is greater Correct answer.
    2. 2 inches
    3. 1/2 inch
    4. 6 inches

    Explanation

    An air gap must provide at least 1 inch or twice the diameter of the effective opening, whichever is greater, measured above the flood level rim. This physical separation protects the potable water supply from contamination.

  4. Question 4Plumbing Code and Regulations

    Which backflow prevention assembly protects against both backsiphonage and backpressure by maintaining a pressure differential?

    1. Atmospheric vacuum breaker
    2. Air gap
    3. Double check valve assembly
    4. Reduced pressure principle assembly Correct answer.

    Explanation

    A reduced pressure principle assembly uses two check valves and a differential relief valve that opens when pressure reverses. It protects against both backsiphonage and backpressure.

  5. Question 5Plumbing Code and Regulations

    How must a temperature and pressure relief valve discharge pipe terminate?

    1. Not more than 6 inches above the floor or receptor Correct answer.
    2. Directly connected to the drainage system
    3. With a threaded cap on the end
    4. Reduced to a smaller diameter at the outlet

    Explanation

    The discharge pipe from a temperature and pressure relief valve must terminate not more than 6 inches above the floor or a receptor. It must not be directly connected to drainage, threaded, or reduced in size.

  6. Question 6Plumbing Code and Regulations

    Under lead-free plumbing requirements, what is the maximum weighted average lead content of wetted surfaces?

    1. 0.5 percent
    2. 0.25 percent Correct answer.
    3. 2 percent
    4. 0.2 percent

    Explanation

    Lead-free plumbing materials are defined as having not more than 0.25 percent weighted average lead content on wetted surfaces. This limit applies to pipes, fittings, and fixtures used for potable water.

  7. Question 7Plumbing Code and Regulations

    How far must a vent pipe extend above a flat roof?

    1. 6 inches Correct answer.
    2. 12 inches
    3. 4 inches
    4. 2 inches

    Explanation

    A vent terminal must extend at least 6 inches above the roof surface. If the roof is used for purposes other than weather protection, the vent must extend at least 7 feet above the roof.

  8. Question 8Plumbing Code and Regulations

    Which material is prohibited for potable water piping in new plumbing installations?

    1. PEX
    2. CPVC
    3. Copper
    4. Lead Correct answer.

    Explanation

    Lead pipe is prohibited for potable water piping because of its health hazards. Approved materials must be lead-free and listed for potable water use.

  9. Question 9Plumbing Code and Regulations

    In plumbing code, what is the building drain?

    1. The vertical main vent extending through the roof
    2. The piping that collects storm water from the roof
    3. The lowest piping that receives soil, waste, and other drainage inside the building and conveys it to the building sewer Correct answer.
    4. The pipe that carries water from the water main to the building

    Explanation

    The building drain is the lowest piping of the drainage system inside the building. It receives soil, waste, and other drainage and ends at the building sewer.

  10. Question 10Plumbing Code and Regulations

    What is the minimum size of a vent pipe for a fixture drain with a 2-inch trap?

    1. 1-1/2 inches
    2. 1 inch
    3. 2 inches
    4. 1-1/4 inches Correct answer.

    Explanation

    A vent must be at least one-half the diameter of the drain it serves and not less than 1-1/4 inches. Half of a 2-inch drain is 1 inch, so the 1-1/4-inch minimum governs.

  11. Question 11Plumbing Code and Regulations

    What is the maximum horizontal support spacing for 1-inch copper tubing?

    1. 10 feet
    2. 6 feet Correct answer.
    3. 4 feet
    4. 5 feet

    Explanation

    Copper tubing up to 1 inch in diameter must be supported at intervals not exceeding 6 feet. Larger tubing may be permitted longer spacing depending on the code table.

  12. Question 12Plumbing Code and Regulations

    A pressure-reducing valve is generally required when the static water pressure exceeds what value?

    1. 50 psi
    2. 80 psi Correct answer.
    3. 75 psi
    4. 60 psi

    Explanation

    Where static water pressure exceeds 80 psi, a pressure-reducing valve is required. A closed system with a pressure-reducing valve also needs thermal expansion control.

  13. Question 13Plumbing Code and Regulations

    What is the minimum nominal diameter of a building sewer?

    1. 3 inches Correct answer.
    2. 2 inches
    3. 2-1/2 inches
    4. 4 inches

    Explanation

    A building sewer must be at least 3 inches in nominal diameter. Larger sizes may be required by the drainage load or local conditions.

  14. Question 14Plumbing Code and Regulations

    What is the minimum clearance from the centerline of a water closet to a side wall?

    1. 15 inches Correct answer.
    2. 12 inches
    3. 18 inches
    4. 24 inches

    Explanation

    A water closet must be installed with at least 15 inches of clearance from its centerline to a side wall. This provides usable space and access for the occupant.

  15. Question 15Plumbing Code and Regulations

    What is the minimum clear width of a water closet compartment?

    1. 24 inches
    2. 28 inches
    3. 36 inches
    4. 30 inches Correct answer.

    Explanation

    A water closet compartment must be at least 30 inches in clear width. The compartment depth and door arrangement are also regulated.

  16. Question 16Plumbing Code and Regulations

    Where is a cleanout required on a vertical drainage stack?

    1. At each floor level where fixtures connect
    2. At the base of the stack above the building drain Correct answer.
    3. At the top of the stack above the roof
    4. At the midpoint of the vertical stack

    Explanation

    A cleanout is required at the base of a vertical drainage stack where it connects to the building drain. Additional cleanouts may be required on long horizontal runs.

  17. Question 17Plumbing Code and Regulations

    What is the maximum developed length of a 1-1/2-inch trap arm from the trap weir to the vent?

    1. 8 feet
    2. 3 feet 6 inches
    3. 5 feet
    4. 6 feet Correct answer.

    Explanation

    The trap arm length is limited to prevent self-siphonage of the trap. For a 1-1/2-inch trap arm, the maximum developed length is 6 feet.

  18. Question 18Plumbing Code and Regulations

    A fixture drain is installed below the flood level rim of the nearest upstream manhole. What device is required?

    1. Air admittance valve
    2. Pressure-reducing valve
    3. Backwater valve Correct answer.
    4. Vacuum breaker

    Explanation

    A backwater valve is required where a fixture drain is below the flood level rim of the nearest upstream manhole. It prevents sewage from backing up into the building.

  19. Question 19Plumbing Code and Regulations

    Where must the temperature and pressure relief valve be located on a storage water heater?

    1. Within the top 6 inches of the tank Correct answer.
    2. On the cold water inlet pipe
    3. At the bottom drain valve
    4. On the discharge pipe 12 inches from the tank

    Explanation

    The temperature and pressure relief valve must be located within the top 6 inches of the storage tank. This is where the hottest water collects and where overheating is detected.

  20. Question 20Plumbing Code and Regulations

    A drainage system is tested with water. What is the minimum head required at the highest point?

    1. 5 feet
    2. 10 feet Correct answer.
    3. 15 feet
    4. 20 feet

    Explanation

    A water test of the drainage system requires a minimum head of 10 feet at the highest point of the system. The test is typically held for at least 15 minutes.

  21. Question 21Plumbing Code and Regulations

    Where is a sump pump allowed to discharge?

    1. Into a septic tank
    2. Into the sanitary sewer
    3. Into the building drain through a trap
    4. To the storm drainage system or exterior grade Correct answer.

    Explanation

    Sump pumps handle groundwater or stormwater and must discharge to an approved storm drainage system or exterior grade. Discharging into the sanitary sewer can overload the system.

  22. Question 22Plumbing Code and Regulations

    A grease interceptor is required for which type of establishment?

    1. A dental office
    2. A car wash
    3. A coin laundry
    4. A commercial food service establishment Correct answer.

    Explanation

    Commercial food service establishments produce grease-laden waste and require a grease interceptor. The interceptor keeps fats, oils, and grease out of the drainage system.

  23. Question 23Plumbing Code and Regulations

    A closed water supply system with a backflow preventer or pressure-reducing valve requires what additional device to control thermal expansion?

    1. Air admittance valve
    2. Vacuum relief valve
    3. Expansion tank Correct answer.
    4. Check valve

    Explanation

    A closed system prevents expanded water from backing into the main, so an expansion tank is required to absorb thermal expansion. Without it, pressure can rise and damage the system.

  24. Question 24Plumbing Code and Regulations

    What is the maximum height of a lavatory rim in an accessible bathroom?

    1. 36 inches
    2. 31 inches
    3. 29 inches
    4. 34 inches Correct answer.

    Explanation

    An accessible lavatory rim must be no higher than 34 inches above the finished floor. Knee and toe clearance are also required beneath the fixture.

  25. Question 25Plumbing Code and Regulations

    When must a plumbing permit be obtained?

    1. Only for commercial work
    2. Before work begins Correct answer.
    3. After rough-in inspection
    4. When the building is sold

    Explanation

    A plumbing permit must be obtained before work begins, except for minor repairs specifically exempted by code. Required inspections are then made at specified stages of construction.

  26. Question 26Plumbing Code and Regulations

    What is the minimum depth of water seal required for a plumbing trap?

    1. 2 inches Correct answer.
    2. 3 inches
    3. 4 inches
    4. 6 inches

    Explanation

    A trap must hold a water seal of not less than 2 inches and not more than 4 inches, measured between the trap weir and the top of the trap dip. The 2-inch minimum keeps sewer gas from passing through ordinary pressure fluctuations.

  27. Question 27Plumbing Code and Regulations

    What is the minimum slope permitted for a 4-inch horizontal drainage pipe?

    1. 1/2 inch per foot
    2. 1/8 inch per foot Correct answer.
    3. 1/4 inch per foot
    4. 1/16 inch per foot

    Explanation

    Drainage pipe slope is set by pipe size: 2-1/2 inches and smaller require 1/4 inch per foot, 3-inch through 6-inch pipe requires 1/8 inch per foot, and 8-inch and larger requires 1/16 inch per foot. A 4-inch pipe therefore needs at least 1/8 inch per foot.

  28. Question 28Plumbing Code and Regulations

    How far must a plumbing vent terminal be kept from a door, window, or gravity air inlet of a building?

    1. 5 feet
    2. 20 feet
    3. 3 feet
    4. 10 feet Correct answer.

    Explanation

    Vent terminals must be located at least 10 feet from any door, window, or gravity air inlet into a building so that the vent discharge does not re-enter occupied space. Terminals must also meet the required height above the roof surface.

  29. Question 29Plumbing Code and Regulations

    A fixture outlet has an effective opening of 1 inch. What is the minimum air gap required to protect the potable water supply?

    1. 2 inches Correct answer.
    2. 3 inches
    3. 1-1/2 inches
    4. 1 inch

    Explanation

    An air gap must be at least twice the diameter of the effective opening of the outlet and never less than 1 inch. For a 1-inch effective opening, twice the opening equals 2 inches, so that becomes the controlling minimum.

  30. Question 30Plumbing Code and Regulations

    A kitchen sink is set in a counter island with no wall or partition within the required venting distance. Which venting arrangement does the code permit for the sink?

    1. A bypass vent taken off the stack above the highest branch
    2. A relief vent one pipe size larger than the drain
    3. An island fixture vent (loop vent) Correct answer.
    4. A continuous waste and vent shared with an adjacent sink

    Explanation

    Island fixture venting uses a loop taken off the drain below the trap and returned to the drain or stack, giving the fixture a vent path without a wall to run a conventional vent up through. The loop must be installed with its own cleanout and arranged so the drain below the fixtures acts as the vent.

  31. Question 31Drainage, Waste, and Vent Systems

    What is the minimum water seal depth required for a plumbing fixture trap?

    1. 2 inches Correct answer.
    2. 4 inches
    3. 3 inches
    4. 1 inch

    Explanation

    A fixture trap must hold a liquid seal of at least 2 inches and no more than 4 inches, which resists sewer gas while keeping the trap from holding an excessive weight of water.

  32. Question 32Drainage, Waste, and Vent Systems

    Why is an S-trap prohibited in a drainage system?

    1. It siphons its own seal as waste discharges Correct answer.
    2. It is difficult to clean
    3. It is larger than a P-trap
    4. It requires an extra vent

    Explanation

    An S-trap discharges into an immediate downward drop after the trap, so the slug of waste water starts a siphon that pulls the seal out of the trap and allows sewer gas into the building.

  33. Question 33Drainage, Waste, and Vent Systems

    The trap arm is the portion of a fixture drain that runs from the trap weir to what point?

    1. The building drain
    2. The vent connection Correct answer.
    3. The fixture outlet
    4. The stack fitting

    Explanation

    The trap arm is the section of fixture drain between the trap weir and the point where that drain is vented. Its length is limited so the trap cannot self-siphon.

  34. Question 34Drainage, Waste, and Vent Systems

    Where a roof is not used for purposes other than weather protection, a vent stack must terminate at least how far above the roof surface?

    1. 18 inches
    2. 12 inches
    3. 2 inches
    4. 6 inches Correct answer.

    Explanation

    Vent terminals must extend at least 6 inches above the roof line. Where the roof is used for other purposes, the required height increases to 12 inches.

  35. Question 35Drainage, Waste, and Vent Systems

    Horizontal drainage piping that is 2-1/2 inches in diameter and smaller must be installed at what minimum slope?

    1. 1/2 inch per foot
    2. 1/4 inch per foot Correct answer.
    3. 1/16 inch per foot
    4. 1/8 inch per foot

    Explanation

    Small-diameter drain pipe needs at least 1/4 inch per foot of fall, roughly two percent, to keep solids moving. Flatter slopes are permitted only for larger pipe sizes.

  36. Question 36Drainage, Waste, and Vent Systems

    What is the smallest diameter permitted for an individual fixture vent?

    1. 1 inch
    2. 1-1/4 inch Correct answer.
    3. 3/4 inch
    4. 2 inch

    Explanation

    An individual fixture vent may not be smaller than 1-1/4 inches, and it must also be sized from the fixture-unit table so it is never smaller than the drain it serves.

  37. Question 37Drainage, Waste, and Vent Systems

    How many fixtures may discharge through a single trap?

    1. Three, if a common vent is installed
    2. One Correct answer.
    3. Two, if they are on the same floor
    4. Any number, if the trap is oversized

    Explanation

    Each fixture must be trapped separately, except for fixtures that are listed and installed as a single unit. A shared trap cannot be vented properly and will siphon.

  38. Question 38Drainage, Waste, and Vent Systems

    A floor drain in an unused warehouse loses its trap seal after several months. Which is the most likely cause?

    1. Capillary action in the drain pipe
    2. Back pressure from the sewer
    3. Momentum from a slug of waste
    4. Evaporation of the seal water Correct answer.

    Explanation

    A trap that receives no water for a long period dries out as the seal evaporates. Trap primers are installed to keep such seals full.

  39. Question 39Drainage, Waste, and Vent Systems

    What is the minimum size of the fixture drain serving a water closet?

    1. 2 inches
    2. 3 inches Correct answer.
    3. 2-1/2 inches
    4. 4 inches

    Explanation

    A water closet requires a drain and trap of at least 3 inches so the flush volume and solid waste can pass without clogging.

  40. Question 40Drainage, Waste, and Vent Systems

    What is the minimum trap size for a kitchen sink?

    1. 2 inch
    2. 3 inch
    3. 1-1/2 inch Correct answer.
    4. 1-1/4 inch

    Explanation

    A kitchen sink needs a trap of at least 1-1/2 inches because of the grease and food solids it carries. A lavatory, by comparison, may use a 1-1/4 inch trap.

  41. Question 41Drainage, Waste, and Vent Systems

    How must a domestic dishwasher drain be connected to the plumbing system?

    1. Directly to the trap arm, downstream of the trap
    2. To the sink tailpiece, upstream of the trap Correct answer.
    3. To the soil stack above the highest fixture served
    4. To the floor drain through a backwater valve

    Explanation

    The dishwasher must discharge on the fixture side of the trap and be protected by an air gap or a high loop, so waste water cannot back up into the appliance and sewer gas cannot reach it.

  42. Question 42Drainage, Waste, and Vent Systems

    Why is a trap primer installed at a floor drain?

    1. To add water to the trap to replace evaporation Correct answer.
    2. To prevent reverse flow during a sewer backup
    3. To admit air when the drain is used
    4. To strain solids before they enter the trap

    Explanation

    A trap primer delivers a small amount of water to the trap on a regular basis, keeping the seal intact where the fixture receives little or no normal flow.

  43. Question 43Drainage, Waste, and Vent Systems

    How does an air admittance valve function?

    1. It opens to admit air when the drain is under negative pressure and closes under positive pressure Correct answer.
    2. It terminates the vent stack above the roof
    3. It serves as both a vent and a wet vent for two fixtures
    4. It relieves positive pressure in the building drain by venting to the outdoors

    Explanation

    An air admittance valve is a one-way device that opens on negative pressure to protect the trap seal and closes when pressure in the system is positive, keeping sewer gas inside the piping.

  44. Question 44Drainage, Waste, and Vent Systems

    A fixture is installed so that its flood level rim is below the level of the next upstream manhole cover. What must be provided?

    1. A backwater valve on the fixture drain Correct answer.
    2. A cleanout at the fixture
    3. A relief vent at the fixture
    4. A trap primer at the fixture

    Explanation

    Fixtures set below the upstream manhole elevation can be flooded by sewage backing up out of the public sewer, so a backwater valve must protect the drain serving them.

  45. Question 45Drainage, Waste, and Vent Systems

    Which fitting is used where a horizontal drain changes direction 90 degrees?

    1. A vent tee
    2. A double sanitary tee
    3. A combination wye with an eighth bend Correct answer.
    4. A sanitary tee

    Explanation

    A horizontal-to-horizontal change of direction needs a fitting that gives a smooth sweep, typically a wye with an eighth bend or a pair of 45-degree bends.

  46. Question 46Drainage, Waste, and Vent Systems

    Which fitting is appropriate where a horizontal fixture drain connects into a vertical soil stack?

    1. A sanitary tee Correct answer.
    2. A double sanitary tee
    3. A wye
    4. A combination wye with an eighth bend

    Explanation

    A sanitary tee has a curved branch that turns the flow downward in the direction of stack flow, making it the standard fitting for a horizontal branch entering a vertical stack.

  47. Question 47Drainage, Waste, and Vent Systems

    Where a soil or waste stack connects to a horizontal building drain, what must be provided?

    1. A backwater valve
    2. A trap primer
    3. A vent at the base
    4. A cleanout at the base of the stack Correct answer.

    Explanation

    A cleanout is required at the base of each stack so the stack bottom and the horizontal drain can be rodded without removing fixtures or breaking piping.

  48. Question 48Drainage, Waste, and Vent Systems

    A vent terminal on a roof must be at least how far horizontally from an openable window, door, or outdoor air intake?

    1. 20 feet
    2. 3 feet
    3. 10 feet Correct answer.
    4. 5 feet

    Explanation

    Vent terminals must be kept at least 10 feet horizontally from windows, doors, and air intakes so sewer gas cannot re-enter the building, unless the terminal is raised at least 3 feet above the opening.

  49. Question 49Drainage, Waste, and Vent Systems

    A vent is connected to a fixture drain within 2 pipe diameters of the trap weir. Why is this prohibited?

    1. It makes the trap too deep
    2. It prevents the vent from being rodded
    3. It forms a crown vent that can siphon the seal Correct answer.
    4. It reduces the drain size below the trap size

    Explanation

    The vent must be far enough downstream that water in the trap cannot bridge to the vent opening and start a siphon. A connection made too close to the weir is a crown vent.

  50. Question 50Drainage, Waste, and Vent Systems

    Horizontal PVC DWV pipe must be supported at intervals not exceeding what distance?

    1. 2 feet
    2. 10 feet
    3. 4 feet Correct answer.
    4. 8 feet

    Explanation

    Plastic DWV pipe is supported at intervals of no more than 4 feet, and also at each joint or fitting, so the pipe does not sag and hold water.

  51. Question 51Drainage, Waste, and Vent Systems

    Which statement best describes a wet vent?

    1. A vent that is installed only in a horizontal position
    2. A vent that is undersized for the fixture it serves
    3. A vent that also carries drainage from fixtures upstream Correct answer.
    4. A vent that terminates inside the building

    Explanation

    A wet vent is a single pipe that carries drainage from one or more fixtures while simultaneously venting another fixture downstream. Its size and the fixtures it may serve are limited by code.

  52. Question 52Drainage, Waste, and Vent Systems

    What is the maximum number of fixtures a circuit vent is permitted to serve?

    1. Two
    2. Sixteen
    3. Eight Correct answer.
    4. Four

    Explanation

    A circuit vent may serve no more than eight fixtures on a single horizontal branch, provided the branch is properly sloped and the vent connects at the downstream end.

  53. Question 53Drainage, Waste, and Vent Systems

    Trap arm length is limited so that the pipe does not drop more than one pipe diameter before it is vented. What problem does this prevent?

    1. The trap becoming an S-trap and self-siphoning Correct answer.
    2. The vent becoming a wet vent
    3. The trap seal exceeding 4 inches
    4. The drain slope exceeding the code maximum

    Explanation

    When a trap arm falls more than one pipe diameter before it reaches the vent, the trap acts like an S-trap and the discharge siphons the seal. That is why the allowable arm length is tied to pipe size and slope.

  54. Question 54Drainage, Waste, and Vent Systems

    A sink is set in a kitchen island with no wall nearby. How is its trap normally vented?

    1. With an island loop vent that rises above the flood level rim Correct answer.
    2. By connecting the trap outlet directly to the soil stack
    3. With a vent connected to the trap arm within 2 pipe diameters of the trap weir
    4. By omitting the vent because the island is open

    Explanation

    Island fixtures use a loop vent: a foot vent taken off the drain runs back to a vertical vent, and the drain rises above the fixture's flood level rim before turning down, so the trap can be vented without a wall.

  55. Question 55Drainage, Waste, and Vent Systems

    Where a vent is subject to frost closure, the vent through the roof must be increased to not less than what size?

    1. 1-1/2 inches
    2. 2 inches
    3. 4 inches
    4. 3 inches Correct answer.

    Explanation

    In cold climates where frost can build up on the inside of the vent, the terminal must be enlarged to at least 3 inches so the frost layer does not close off the vent.

  56. Question 56Drainage, Waste, and Vent Systems

    What is the minimum permitted slope for a horizontal 2-inch drainage pipe?

    1. 1/2 inch per foot
    2. 1/16 inch per foot
    3. 1/8 inch per foot
    4. 1/4 inch per foot Correct answer.

    Explanation

    Horizontal drainage pipe 2-1/2 inches and smaller must be graded at a minimum of 1/4 inch per foot so scouring velocity keeps solids moving. Larger pipe may be installed at 1/8 inch per foot, and 8-inch and larger at 1/16 inch per foot.

  57. Question 57Drainage, Waste, and Vent Systems

    What water-seal depth must a plumbing trap maintain?

    1. 6 to 8 inches
    2. 2 to 4 inches Correct answer.
    3. 4 to 6 inches
    4. 1 to 2 inches

    Explanation

    A trap must hold a seal of at least 2 inches and not more than 4 inches, measured from the trap weir to the top of the dip. The minimum resists siphonage, and the maximum keeps the trap from becoming a settling chamber for waste.

  58. Question 58Drainage, Waste, and Vent Systems

    What is the minimum height at which a vent terminal must extend above the roof surface?

    1. 6 inches Correct answer.
    2. 18 inches
    3. 24 inches
    4. 12 inches

    Explanation

    The code minimum is 6 inches above the roof surface, which keeps the opening clear of snow and surface water. Where the roof is used for purposes other than weather protection, the vent must be raised higher, commonly to 7 feet.

  59. Question 59Drainage, Waste, and Vent Systems

    Which term describes the pipe that carries sewage from the end of the building drain to the public sewer or private disposal system?

    1. Building drain
    2. Soil stack
    3. Storm drain
    4. Building sewer Correct answer.

    Explanation

    The building sewer begins where the building drain ends, typically at or just outside the building wall, and runs to the public sewer or a private disposal system. The building drain itself is the portion inside the building that receives the discharge of the soil and waste stacks.

  60. Question 60Drainage, Waste, and Vent Systems

    What is the maximum permitted vertical distance between a fixture outlet and the weir of its trap?

    1. 12 inches
    2. 30 inches
    3. 36 inches
    4. 24 inches Correct answer.

    Explanation

    The vertical drop from the fixture outlet to the trap weir is limited to 24 inches so the trap stays close to the fixture it serves. Excessive drop allows waste to gain velocity and splash through the trap, and it makes the surface between the outlet and the trap hard to clean.

  61. Question 61Drainage, Waste, and Vent Systems

    A clothes washer standpipe must be installed so that its top is within what height range above the trap weir?

    1. 12 to 30 inches
    2. 24 to 48 inches
    3. 30 to 60 inches
    4. 18 to 42 inches Correct answer.

    Explanation

    The standpipe must rise at least 18 inches to prevent the washer's discharge from splashing out and no more than 42 inches to keep the pump from working against excessive head. Within that range the standpipe also provides the required air break for the washer hose.

  62. Question 62Drainage, Waste, and Vent Systems

    How must a horizontal run of vent pipe be graded?

    1. Level, with no grade at all
    2. Sloped back toward the drain it serves Correct answer.
    3. Sloped away from the drain so it drains out the roof terminal
    4. Sloped at 1/4 inch per foot away from the fixture it serves

    Explanation

    Horizontal vent pipe must slope back toward the drain so condensation, rainwater, or splash can run into the drainage system instead of pooling in the vent and blocking it. A level or outward-sloping vent can collect water and effectively close the vent.

  63. Question 63Drainage, Waste, and Vent Systems

    Which best defines a stack vent?

    1. A vent connected to a fixture drain within two diameters of the trap
    2. The extension of a stack above the highest branch Correct answer.
    3. A vent that serves only the uppermost fixture connected to a stack
    4. A separate vertical vent installed beside the stack to relieve pressure

    Explanation

    A stack vent is simply the continuation of a soil or waste stack above the highest horizontal branch connection, and it is sized as a vent above that point. It is not a separate pipe; a separate vertical vent run beside a stack is a vent stack.

  64. Question 64Drainage, Waste, and Vent Systems

    Fixtures are installed in a basement that is below the level of the public sewer. How must their drainage be handled?

    1. By a separate gravity drain that discharges at grade
    2. By direct connection to the building drain with a backwater valve
    3. By giving the fixtures a deeper trap seal
    4. By pumping from a sump into the building drain Correct answer.

    Explanation

    Waste that cannot flow by gravity to the sewer must be collected in a sump and lifted by a sewage ejector or grinder pump that discharges into the building drain or building sewer. The receiving sump must be vented and the discharge arranged so backflow cannot enter the basement.

  65. Question 65Drainage, Waste, and Vent Systems

    Which fixture may not be served by a combination waste and vent system?

    1. Water closet Correct answer.
    2. Drinking fountain
    3. Lavatory
    4. Floor drain

    Explanation

    A combination waste and vent system relies on an oversized drain that leaves air space above the waste stream, so it is limited to fixtures that discharge relatively gently. Water closets and urinals, which release large slugs of waste, are not permitted on such a system.

  66. Question 66Drainage, Waste, and Vent Systems

    What must be provided where the building drain connects to the building sewer?

    1. A fresh-air inlet
    2. A backwater valve
    3. A trap
    4. A cleanout Correct answer.

    Explanation

    A cleanout is required at or near the junction of the building drain and building sewer so the line can be rodded from outside the building in both directions. A trap at that point would be a house trap, which modern codes do not require, and a backwater valve is installed only where backflow is a hazard.

  67. Question 67Drainage, Waste, and Vent Systems

    Where should a grease interceptor be installed?

    1. On the vent branch serving the kitchen sink
    2. In the basement, below the lowest kitchen fixture
    3. Close to the fixtures served and accessible for cleaning Correct answer.
    4. Outside the building, downstream of the building sewer connection

    Explanation

    A grease interceptor must be reachable for periodic cleaning and located as close as practicable to the fixtures it serves. If it is set too far downstream, grease cools and congeals in the pipe before it can be captured.

  68. Question 68Drainage, Waste, and Vent Systems

    What is the purpose of a yoke vent?

    1. To prevent frost closure of a roof vent terminal in cold climates
    2. To vent the topmost fixture branch connected to the soil stack
    3. To supply make-up air to a grease interceptor serving a kitchen sink
    4. To equalize pressure between a soil stack and its vent stack Correct answer.

    Explanation

    A yoke vent connects the soil or waste stack to the vent stack, usually at intervals in a tall building, so pressure differences between the two are relieved. This protects trap seals in the lower branches from blow-back or siphonage caused by stack flow.

  69. Question 69Drainage, Waste, and Vent Systems

    A soil stack receives the discharge of more than 10 branch intervals. What must be provided for that stack?

    1. A vent stack or relief vent Correct answer.
    2. A backwater valve at the stack base
    3. An increase in stack diameter to 4 inches
    4. A cleanout at each branch interval

    Explanation

    When a stack carries more than 10 branch intervals, the flow in the lower portion can create pressure fluctuations that siphon or blow out trap seals. A vent stack or a relief vent is required to equalize pressure in the lower part of the stack.

  70. Question 70Drainage, Waste, and Vent Systems

    A lavatory trap arm is longer than the distance allowed before the pipe drops one full pipe diameter. What is the correct remedy?

    1. Reduce the slope of the trap arm by half to slow the flow
    2. Increase the diameter of the trap arm by one pipe size
    3. Install a vent at the permitted trap arm distance Correct answer.
    4. Install a deeper-seal trap at the fixture

    Explanation

    A trap must be vented before its arm drops one pipe diameter, otherwise the slug of water can siphon the seal. When the fixture is too far from the available vent, a vent is added at the maximum permitted distance and the remainder of the run is installed as part of the vented drain.

  71. Question 71Water Supply and Distribution

    A pressure gauge on a water main reads 60 psi. What is the equivalent pressure head in feet of water?

    1. 26 ft
    2. 60 ft
    3. 260 ft
    4. 139 ft Correct answer.

    Explanation

    One pound per square inch supports a column of water about 2.31 feet high. Multiplying 60 psi by 2.31 gives approximately 139 feet of head. This conversion is used constantly when comparing gauge readings with elevation changes in a piping system.

  72. Question 72Water Supply and Distribution

    Which device is commonly installed at a hose bibb to prevent backsiphonage?

    1. Pressure-reducing valve
    2. Reduced-pressure zone assembly
    3. Atmospheric vacuum breaker Correct answer.
    4. Double-check valve assembly

    Explanation

    An atmospheric vacuum breaker admits air when supply pressure drops, breaking the siphon at the outlet. Hose bibbs are a classic backsiphonage location because a hose can be submerged in a contaminant. The other assemblies listed are used for other purposes or other hazard levels.

  73. Question 73Water Supply and Distribution

    Water hammer in a supply system is most often caused by which condition?

    1. Air trapped in the water main
    2. Excessive pipe insulation
    3. Sudden stoppage of flow by a quickly closed valve Correct answer.
    4. Low water temperature

    Explanation

    When a valve closes quickly, the moving column of water is stopped abruptly and its momentum creates a pressure surge. That surge travels through the piping and produces the banging noise called water hammer. Arrestors or slower-closing valves absorb or reduce the surge.

  74. Question 74Water Supply and Distribution

    An air gap provides backflow protection because it does what?

    1. It filters sediment from the water
    2. It creates a physical separation between the supply outlet and the flood level Correct answer.
    3. It removes dissolved gases
    4. It maintains a constant system pressure

    Explanation

    An air gap is the unobstructed vertical distance between a supply outlet and the flood-level rim of the receiving fixture. Because no physical connection exists, neither backsiphonage nor backpressure can draw contamination into the supply. It is considered the highest level of backflow protection.

  75. Question 75Water Supply and Distribution

    What is the purpose of a pressure-reducing valve on a domestic water service?

    1. Reduce excessive street pressure to a safe level Correct answer.
    2. Remove chlorine from the water
    3. Increase pressure to upper floors
    4. Prevent thermal expansion

    Explanation

    A pressure-reducing valve lowers high supply pressure to a set downstream pressure that the piping and fixtures can safely withstand. Excessive pressure damages fixtures, causes noise, and shortens appliance life. The valve regulates downstream pressure regardless of higher street pressure.

  76. Question 76Water Supply and Distribution

    Which water supply pipe material is commonly joined with lead-free solder?

    1. Galvanized steel
    2. PEX
    3. CPVC
    4. Copper Correct answer.

    Explanation

    Copper tube is joined by soldering with lead-free solder or by brazing. PEX uses mechanical fittings, CPVC uses solvent cement, and galvanized steel uses threaded fittings. Copper remains common for potable water because of its durability and smooth interior.

  77. Question 77Water Supply and Distribution

    PEX tubing is typically connected using which method?

    1. Threaded fittings
    2. Solvent cement
    3. Crimp or press fittings Correct answer.
    4. Lead-tin solder

    Explanation

    PEX is joined with mechanical fittings such as crimp rings, clamp rings, or press tools. Solvent cement does not bond PEX, and soldering would damage the tubing. Each manufacturer specifies compatible fittings and tooling.

  78. Question 78Water Supply and Distribution

    Buried water service lines are installed below the local frost line primarily to do what?

    1. Improve flow rate
    2. Discourage root growth
    3. Prevent freezing Correct answer.
    4. Reduce noise transmission

    Explanation

    The frost line is the depth to which soil normally freezes in winter. Placing the service below that depth keeps the water from freezing and bursting the pipe. Local code specifies the required cover depth based on climate.

  79. Question 79Water Supply and Distribution

    The static pressure at a water meter is 70 psi. A fixture is located 20 ft above the meter. Neglecting friction, what is the approximate static pressure at the fixture?

    1. 61 psi Correct answer.
    2. 70 psi
    3. 79 psi
    4. 52 psi

    Explanation

    Each foot of elevation reduces pressure by about 0.433 psi, so 20 ft costs about 8.7 psi. Subtracting that from 70 psi gives roughly 61 psi at the higher fixture. Pressure drops with height because the water column must be lifted.

  80. Question 80Water Supply and Distribution

    In a closed potable water system, what is the function of a thermal expansion tank?

    1. Absorb the increased volume of heated water Correct answer.
    2. Remove chlorine
    3. Increase pump output
    4. Prevent backflow

    Explanation

    When water is heated in a closed system, it expands and has nowhere to go, causing pressure to rise sharply. A expansion tank provides an air cushion that absorbs the extra volume. This protects piping, fixtures, and the water heater from overpressure.

  81. Question 81Water Supply and Distribution

    What is the primary purpose of the pressure tank in a private well system?

    1. Filter iron from the water
    2. Increase well yield
    3. Maintain pressure between pump cycles and reduce pump cycling Correct answer.
    4. Chlorinate the water

    Explanation

    A pressure tank stores water under air pressure so fixtures have flow between pump runs. This limits how often the pump starts and stops, extending its life. It does not treat water or increase the amount the well can produce.

  82. Question 82Water Supply and Distribution

    Friction loss in a given length of water pipe increases most nearly in proportion to what?

    1. The velocity
    2. The pipe diameter
    3. The square of the velocity Correct answer.
    4. The square root of pressure

    Explanation

    Friction loss rises sharply as water moves faster, approximately with the square of the velocity in common design ranges. Doubling the velocity therefore roughly quadruples the friction loss. This is why undersized pipes cause large pressure drops at high demand.

  83. Question 83Water Supply and Distribution

    Which backflow prevention assembly protects against both backsiphonage and backpressure?

    1. Barometric loop
    2. Atmospheric vacuum breaker
    3. Reduced-pressure zone assembly Correct answer.
    4. Dual check valve

    Explanation

    A reduced-pressure zone assembly uses two check valves with a relief valve between them, protecting against both backsiphonage and backpressure. It is used for high-hazard connections. The other devices have narrower applications or limitations.

  84. Question 84Water Supply and Distribution

    The developed length of a water piping run is measured in which way?

    1. Only the vertical rise
    2. The straight-line distance from meter to farthest fixture
    3. Along the centerline of the pipe including fittings and offsets Correct answer.
    4. Only the horizontal distance

    Explanation

    Developed length follows the actual path of the pipe, including elbows, offsets, and risers, because each fitting adds resistance. It is longer than the straight-line distance between endpoints. Sizing calculations use developed length plus equivalent lengths for fittings.

  85. Question 85Water Supply and Distribution

    A newly installed water supply system is typically tested for leaks in which manner?

    1. Flushing with hot water
    2. Filling with air at 5 psi
    3. Pressurizing with water at 100 psi for at least 15 minutes Correct answer.
    4. Running all fixtures for one hour

    Explanation

    Plumbing codes commonly require a hydrostatic water test at 100 psi, or at working pressure if higher, held for at least 15 minutes with no drop. This reveals leaks before the system is closed up. Air testing is generally not permitted for this purpose.

  86. Question 86Water Supply and Distribution

    A thermal expansion tank for a closed potable system must be sized based on what information?

    1. Fixture unit count
    2. System water volume and maximum temperature rise Correct answer.
    3. Pipe diameter only
    4. Water meter size

    Explanation

    The amount of expansion depends on how much water is in the system and how much its temperature rises. Tank sizing uses those two factors along with the supply pressure and the allowable pressure increase. Pipe diameter and meter size do not determine expansion volume.

  87. Question 87Water Supply and Distribution

    Which pipe material is prohibited for potable water supply because of health hazards?

    1. Copper tube
    2. Ductile iron pipe
    3. CPVC pipe
    4. Lead pipe Correct answer.

    Explanation

    Lead pipe and lead-based solder are prohibited in potable water systems because lead can leach into drinking water and cause serious health effects. Copper, CPVC, and ductile iron with proper linings are acceptable materials. Older lead service lines are commonly replaced for this reason.

  88. Question 88Water Supply and Distribution

    A pressure gauge on a hose bibb reads 65 psi with no water flowing. When a nearby faucet is opened, the gauge drops to 45 psi. What does the drop most directly indicate?

    1. Backflow at the hose bibb
    2. Friction loss and pressure loss in the piping between the source and the point of flow Correct answer.
    3. Thermal expansion of the water
    4. A defective gauge

    Explanation

    With no flow, the gauge shows static pressure; once water moves, friction and velocity-related losses reduce the reading at that point. A large drop suggests restrictive or undersized piping between the source and the gauge. This is why residual pressure is measured while water is flowing.

  89. Question 89Water Supply and Distribution

    Upper floors of a tall building have low fixture pressure while the ground floor is adequate. What is the most appropriate correction?

    1. Increase the ground-floor pipe size
    2. Reduce the water heater temperature
    3. Install an expansion tank
    4. Install a booster pump system Correct answer.

    Explanation

    Adequate pressure at the bottom but low pressure at the top indicates the elevation loss is not being overcome. A booster pump raises the pressure to the upper zones. Enlarging ground-floor piping or adjusting the water heater does not restore lost elevation pressure.

  90. Question 90Water Supply and Distribution

    A screw-on atmospheric vacuum breaker is installed on a hose bibb that feeds a pressurized fertilizer sprayer. Why is this arrangement unsafe?

    1. The vacuum breaker is installed too high
    2. The device reduces flow too much
    3. The hose is too long
    4. The device does not protect against backpressure Correct answer.

    Explanation

    An atmospheric vacuum breaker protects against backsiphonage only, because it relies on the supply pressure dropping to open the air inlet. A pressurized sprayer can push fertilizer backward into the supply by backpressure, which the device cannot stop. A reduced-pressure zone assembly or air gap is needed for that hazard.

  91. Question 91Water Supply and Distribution

    A pressure gauge at the top of a 100-ft vertical riser reads 20 psi. Neglecting friction, what is the pressure at the bottom of the riser?

    1. 43 psi
    2. 63 psi Correct answer.
    3. 20 psi
    4. 77 psi

    Explanation

    A 100-ft column of water creates about 43.3 psi, because each foot adds approximately 0.433 psi. Adding that to the 20 psi at the top gives about 63 psi at the bottom. Pressure increases with depth in a static system.

  92. Question 92Water Supply and Distribution

    A bladder-type well tank has a precharge of 40 psi, but the pump cut-in pressure is 30 psi. What is the likely result?

    1. The pump will run continuously without shutting off
    2. The tank will become waterlogged with air
    3. The tank will fill completely with water
    4. The pump will short cycle and the tank will have little usable drawdown Correct answer.

    Explanation

    Tank precharge is normally set about 2 psi below the pump cut-in pressure. If the precharge is higher than cut-in, the pump must raise pressure before any water enters the tank, so only a small volume is stored and the pump cycles rapidly. Correcting the precharge restores usable drawdown.

  93. Question 93Water Supply and Distribution

    Water flows steadily through a horizontal pipe that reduces from 1 inch diameter to 1/2 inch diameter. What happens to the velocity in the smaller section?

    1. It doubles
    2. It stays the same
    3. It halves
    4. It quadruples Correct answer.

    Explanation

    By continuity, the same flow rate through one-quarter of the cross-sectional area must move four times as fast. Halving the diameter reduces the area by a factor of four. The higher velocity also increases friction loss and lowers pressure in that section.

  94. Question 94Water Supply and Distribution

    A pump delivers water against a total dynamic head of 120 ft. What is the approximate discharge pressure in psi?

    1. 277 psi
    2. 52 psi Correct answer.
    3. 120 psi
    4. 26 psi

    Explanation

    Pressure in psi equals head in feet divided by 2.31. Dividing 120 ft by 2.31 gives about 52 psi. Total dynamic head includes elevation, friction, and pressure head requirements.

  95. Question 95Water Supply and Distribution

    What is the primary purpose of a water hammer arrestor installed near a quick-closing valve?

    1. Cushion the shock wave from a fast-closing valve Correct answer.
    2. Isolate the fixture branch during repairs
    3. Drain the piping system for winterization
    4. Raise the static pressure at the fixture outlet

    Explanation

    When a quick-closing valve shuts, the moving column of water is stopped abruptly and its momentum creates a high-pressure shock wave that travels through the piping. A water hammer arrestor contains a gas cushion or spring that absorbs this energy, smoothing the surge and preventing banging and pipe damage.

  96. Question 96Water Supply and Distribution

    Where is a curb stop normally located on a building water service?

    1. At the property line near the main Correct answer.
    2. Inside the building beside the water heater
    3. At the highest fixture in the system
    4. On the discharge side of the meter

    Explanation

    The curb stop is the utility-controlled valve on the service line, installed in a curb box at or near the property line between the public main and the building. It lets the water supplier shut off flow to the property without entering the structure.

  97. Question 97Water Supply and Distribution

    A chemical tank is filled from a potable water line. Which arrangement gives the highest level of backflow protection at that connection?

    1. A reduced-pressure principle zone assembly with a relief port
    2. A pressure vacuum breaker on the discharge of the tank fill line
    3. A double check valve assembly with two independently acting check valves
    4. An air gap between the pipe outlet and the tank rim Correct answer.

    Explanation

    An air gap provides a physical, unobstructed separation between the potable outlet and the tank's flood-level rim, so backflow is impossible even under backpressure or backsiphonage. Mechanical assemblies rely on check valves and relief ports that can foul or fail, which is why an air gap is rated as the highest degree of protection.

  98. Question 98Water Supply and Distribution

    Water moves at 8 ft/s through a section of nominal 1-inch pipe whose inside diameter is approximately 1.0 inch. What is the approximate flow rate?

    1. About 5 gpm
    2. About 40 gpm
    3. About 20 gpm Correct answer.
    4. About 80 gpm

    Explanation

    The cross-sectional area is roughly 0.00545 sq ft, so flow equals area times velocity, or about 0.0436 cu ft/s. Multiplying by 448.8 to convert cubic feet per second to gallons per minute gives about 19.6 gpm, which rounds to 20 gpm.

  99. Question 99Water Supply and Distribution

    A 60-year-old building has original galvanized steel water piping. Fixture flow has declined steadily for years and the water is occasionally rusty. Which explanation fits these symptoms best?

    1. Static pressure at the meter has fallen below the minimum for the fixtures
    2. The water meter is undersized for the peak demand
    3. Tuberculation from internal corrosion has narrowed the pipe bore Correct answer.
    4. The pressure-reducing valve is stuck in the wide-open position

    Explanation

    Galvanized steel corrodes from the inside, and the resulting tubercles and mineral scale reduce the effective diameter and add roughness, so flow drops progressively. Iron corrosion products also tint the water, which explains the rusty appearance at fixtures.

  100. Question 100Plumbing Fixtures and Appliances

    A floor-mounted water closet is ordered with a 12-inch rough-in. What does the 12 inches measure?

    1. Finished wall to center of the closet flange Correct answer.
    2. Side wall to the center of the closet flange
    3. Subfloor to the top of the closet flange
    4. Finished wall to the front of the bowl

    Explanation

    Water closet rough-in is measured from the finished wall surface to the center line of the closet flange, which is the drain opening in the floor. A 12-inch rough-in is the most common, with 10-inch and 14-inch rough-ins used when the drain is located differently. The bowl dimension and the side clearance do not enter into the rough-in dimension.

  101. Question 101Plumbing Fixtures and Appliances

    What is the minimum liquid seal depth required for a plumbing fixture trap?

    1. 4 inches
    2. 1 inch
    3. 3 inches
    4. 2 inches Correct answer.

    Explanation

    Fixture traps must hold a liquid seal of at least 2 inches and not more than 4 inches. The 2-inch minimum resists evaporation and normal pressure fluctuations in the drainage system, while the 4-inch maximum keeps the trap from being excessively heavy and difficult to prime.

  102. Question 102Plumbing Fixtures and Appliances

    A dishwasher drain hose discharges into a sink tailpiece without an air gap fitting. How high above the sink flood level rim must the hose rise?

    1. 2 inches above the sink flood level rim Correct answer.
    2. Level with the sink flood level rim
    3. 1 inch above the sink flood level rim
    4. 6 inches above the sink flood level rim

    Explanation

    Where no air gap is installed, the drain hose must be elevated so its outlet is at least 2 inches above the flood level rim of the sink, or secured to the underside of the countertop. This high loop prevents sink water from siphoning back into the dishwasher. The hose must also be supported so it cannot drop below that elevation.

  103. Question 103Plumbing Fixtures and Appliances

    A temperature and pressure relief valve for a residential storage water heater is normally rated at what setpoint?

    1. 200 degrees F and 175 psi
    2. 210 degrees F and 150 psi Correct answer.
    3. 150 degrees F and 100 psi
    4. 180 degrees F and 125 psi

    Explanation

    Standard T&P valves for domestic storage water heaters open at a maximum of 210 degrees F and 150 psi. The valve protects the tank if the thermostat fails or the thermostat is set too high. The rating must not exceed the working pressure stamped on the heater's rating plate.

  104. Question 104Plumbing Fixtures and Appliances

    What is the minimum drain size permitted for a water closet?

    1. 3 inch Correct answer.
    2. 1-1/2 inch
    3. 2 inch
    4. 4 inch

    Explanation

    A water closet must discharge into a drain of at least 3 inches in diameter. The 3-inch size carries solids reliably and matches the standard closet flange and bowl outlet. Smaller drains are permitted only for fixtures that discharge liquid waste.

  105. Question 105Plumbing Fixtures and Appliances

    In the standard water supply fixture unit tables, what value is assigned to a private lavatory?

    1. 2.5
    2. 1.5
    3. 1 Correct answer.
    4. 2

    Explanation

    The fixture unit tables assign 1 water supply fixture unit to a private lavatory. Fixture units estimate the probable demand a fixture places on the supply system so that pipe sizing can be calculated. Higher values are assigned to fixtures that fill or flush more quickly, such as a water closet.

  106. Question 106Plumbing Fixtures and Appliances

    What is the minimum trade size of the trap and fixture drain serving a lavatory?

    1. 1-1/4 inch Correct answer.
    2. 1-1/2 inch
    3. 1 inch
    4. 3/4 inch

    Explanation

    A lavatory requires a trap and fixture drain of at least 1-1/4 inches. This size carries the low-volume waste from a hand basin without clogging. A kitchen sink, by contrast, needs a 1-1/2-inch trap and drain.

  107. Question 107Plumbing Fixtures and Appliances

    A check valve is installed on the cold water supply to a water heater in a house that is otherwise an open system. What must be added to the installation?

    1. A larger temperature and pressure relief valve
    2. A recirculation pump on the hot water line
    3. A pressure-reducing valve on the hot water line
    4. A thermal expansion tank Correct answer.

    Explanation

    A check valve, backflow preventer, or pressure-reducing valve turns the system into a closed system, so heated water has nowhere to expand. A thermal expansion tank absorbs that increased volume and keeps the pressure from lifting the relief valve or damaging piping. Without it, the T&P valve will weep each time the heater recovers.

  108. Question 108Plumbing Fixtures and Appliances

    What is the minimum nominal size of the water supply branch to a flushometer-operated water closet?

    1. 1-1/4 inch
    2. 1 inch Correct answer.
    3. 3/4 inch
    4. 1/2 inch

    Explanation

    A flushometer water closet needs a 1-inch supply branch to deliver its flush volume in the required time at adequate residual pressure. Urinals with flushometers require a 3/4-inch branch. Undersized branches cause weak or incomplete flushes.

  109. Question 109Plumbing Fixtures and Appliances

    Which device is required at a shower to keep the water temperature stable when other fixtures in the building are used?

    1. A check valve on the cold line
    2. A two-handle faucet
    3. A pressure-balancing mixing valve Correct answer.
    4. A gate valve on the hot line

    Explanation

    Pressure-balancing and thermostatic mixing valves sense changes in supply pressure or temperature and adjust the hot and cold proportions to hold the outlet temperature steady. This protects bathers from a sudden slug of hot water when a nearby toilet flushes. Simple two-handle valves provide no such protection.

  110. Question 110Plumbing Fixtures and Appliances

    What is the maximum allowable vertical distance from a fixture outlet to the trap weir?

    1. 12 inches
    2. 24 inches Correct answer.
    3. 30 inches
    4. 18 inches

    Explanation

    The vertical drop from the fixture outlet to the trap weir is limited to 24 inches. A longer drop lets waste gain enough velocity to siphon the trap seal as it falls. Fixtures with deep-set outlets, such as some laboratory sinks, may need additional venting to prevent self-siphonage.

  111. Question 111Plumbing Fixtures and Appliances

    What is the minimum drain size for a food waste disposer?

    1. 2 inch
    2. 1-1/4 inch
    3. 1/2 inch
    4. 1-1/2 inch Correct answer.

    Explanation

    A food waste disposer discharges through a trap and drain of at least 1-1/2 inches, matching the kitchen sink it serves. The larger size handles the ground food solids without clogging. The disposer must also be listed and installed per the manufacturer's instructions.

  112. Question 112Plumbing Fixtures and Appliances

    Under accessibility rules, what is the maximum rim height above the floor for a standard wall-hung urinal?

    1. 20 inches
    2. 24 inches
    3. 17 inches Correct answer.
    4. 27 inches

    Explanation

    An accessible standard urinal must have its rim no more than 17 inches above the finished floor. The lower rim allows use from a seated or standing position by people of shorter stature and by wheelchair users. Juvenile-height urinals have a different allowance.

  113. Question 113Plumbing Fixtures and Appliances

    What is the minimum required height of a clothes washer standpipe above its trap weir?

    1. 36 inches
    2. 24 inches
    3. 18 inches Correct answer.
    4. 12 inches

    Explanation

    A clothes washer standpipe must be at least 18 inches and not more than 42 inches above the trap weir. The minimum length keeps the machine's hose outlet above the standpipe so suds and waste cannot overflow, while the maximum limits splashing. The standpipe must also be at least 2 inches in diameter.

  114. Question 114Plumbing Fixtures and Appliances

    A floor drain in a rarely used mechanical room is losing its trap seal to evaporation. What is the proper correction?

    1. Install a deeper trap body
    2. Install a trap primer on a metered water supply Correct answer.
    3. Replace the floor drain with a cleanout
    4. Cap the drain opening between uses

    Explanation

    A trap primer automatically adds a small amount of water to the trap to maintain the seal where the fixture is not used regularly. This prevents sewer gas from entering the space through a dry trap. Simply capping the drain would defeat its purpose and would usually create an unvented condition.

  115. Question 115Plumbing Fixtures and Appliances

    What device must protect an outside sill cock that is used to attach a garden hose?

    1. A pressure-reducing valve
    2. A floor drain
    3. A check valve
    4. A vacuum breaker Correct answer.

    Explanation

    A hose connection is a cross-connection, because a hose can be submerged in a pool, bucket, or chemical sprayer and allow backflow into the potable supply. A vacuum breaker, either integral to the sill cock or threaded onto it, opens to atmosphere when pressure drops. Codes require this protection on every hose bibb.

  116. Question 116Plumbing Fixtures and Appliances

    What is the minimum distance from the center line of a water closet to a side wall or partition?

    1. 18 inches
    2. 24 inches
    3. 21 inches
    4. 15 inches Correct answer.

    Explanation

    A water closet must be centered at least 15 inches from any side wall or partition, giving a minimum 30-inch wide space. At least 21 inches of clear space must also be provided in front of the bowl. These clearances allow comfortable use and access for cleaning.

  117. Question 117Plumbing Fixtures and Appliances

    How should a closet flange be set in relation to the finished floor?

    1. At least 2 inches above the floor
    2. Flush with the subfloor only
    3. At least 1 inch below the floor
    4. Flush with or slightly above the floor Correct answer.

    Explanation

    The closet flange should be installed flush with, or slightly above, the finished floor. This lets the wax ring compress between the flange and the bowl without leaving a gap under the flange where water can escape. The flange must also be securely fastened to the floor structure.

  118. Question 118Plumbing Fixtures and Appliances

    Under accessibility rules, what is the maximum height of a drinking fountain spout outlet above the floor?

    1. 36 inches Correct answer.
    2. 42 inches
    3. 30 inches
    4. 27 inches

    Explanation

    An accessible drinking fountain must have its spout outlet between 15 inches and 36 inches above the finished floor. The upper limit keeps the spout reachable from a wheelchair and usable by standing people of short stature. The water flow must also be located near the front of the unit.

  119. Question 119Plumbing Fixtures and Appliances

    How must the discharge pipe from a water heater temperature and pressure relief valve terminate?

    1. Within 6 inches of the floor, untrapped Correct answer.
    2. At least 12 inches above the floor, threaded
    3. Below the floor drain trap seal
    4. Outside the building above grade

    Explanation

    The relief valve discharge must run full size, by gravity, with no traps, no valves, and no threaded end, and it must terminate within 6 inches of the floor or outside the building. The piping must be rated for the valve's temperature and pressure so it does not fail during a discharge. A threaded end is prohibited because it invites capping, which could block the relief path.

  120. Question 120Plumbing Fixtures and Appliances

    A soda fountain carbonator is connected permanently to the building water supply. What backflow protection does this connection require?

    1. An air gap or an RPZ assembly Correct answer.
    2. A hose-bibb vacuum breaker
    3. A single check valve
    4. A dual check valve

    Explanation

    A carbonator is a high-hazard connection because CO2-pressurized water and syrup can be forced back into the potable lines. Codes require an air gap or a reduced-pressure-principle assembly, the two protections suitable for high hazards. A simple check valve is not adequate for this degree of risk.

  121. Question 121Plumbing Fixtures and Appliances

    Under accessibility rules, what minimum height of knee clearance must be provided beneath a lavatory?

    1. 32 inches
    2. 27 inches
    3. 34 inches
    4. 29 inches Correct answer.

    Explanation

    The knee clearance beneath an accessible lavatory must be at least 29 inches high, 30 inches wide, and 11 inches deep at the toe space. This clearance lets a wheelchair roll under the fixture so the user can reach the faucet. The lavatory rim itself may be no higher than 34 inches.

  122. Question 122Plumbing Fixtures and Appliances

    Where must a temperature and pressure relief valve be located on a storage-type water heater?

    1. In the cold water inlet line
    2. Within the top 6 inches of the tank Correct answer.
    3. On the flue collar of the vent
    4. At the bottom drain valve

    Explanation

    The relief valve must be installed with its temperature-sensing element in the top 6 inches of the tank, where the hottest water collects. This location lets the valve sense an overheating condition before the entire tank is affected. The valve must also be rated for the tank's capacity and working pressure.

  123. Question 123Plumbing Fixtures and Appliances

    What is the maximum temperature of water discharged into a bathtub in a dwelling unit?

    1. 100 degrees F
    2. 120 degrees F Correct answer.
    3. 130 degrees F
    4. 110 degrees F

    Explanation

    Hot water delivered to a bathtub is limited to 120 degrees F to reduce the risk of scald injury. Where the heater is set higher for storage capacity, a tempering or thermostatic mixing valve is installed to limit the delivered temperature. The limit applies to the water as it enters the tub, not to the setpoint of the thermostat.

  124. Question 124Water Heaters

    Combination temperature-and-pressure relief valves used on residential storage water heaters are typically rated to open at which temperature and pressure?

    1. 150°F and 125 psi
    2. 250°F and 100 psi
    3. 180°F and 150 psi
    4. 210°F and 150 psi Correct answer.

    Explanation

    The standard combination relief valve for a residential storage water heater is rated at 210°F and 150 psi, which is above normal operating conditions but below the tank's design limits. The temperature element is set to open well below the boiling point of water so the tank cannot build pressure from overheating. A valve rated lower than the tank's normal high-limit range would nuisance-trip during ordinary operation.

  125. Question 125Water Heaters

    For a typical residential dwelling, what is the generally accepted maximum hot water delivery temperature at fixtures to limit scald risk?

    1. 100°F
    2. 160°F
    3. 140°F
    4. 120°F Correct answer.

    Explanation

    About 120°F is the accepted upper limit for hot water delivered to residential fixtures, because full-temperature water above that can scald quickly, especially children and the elderly. Tanks are sometimes stored hotter to control bacteria, in which case a tempering or mixing valve is installed at the outlet. Lower than about 110°F risks an inadequate supply at the fixtures.

  126. Question 126Water Heaters

    A magnesium or aluminum rod installed through the top of a steel water heater tank serves what purpose?

    1. It provides a grounding electrode for the electrical system
    2. It improves heat transfer from the burner to the water
    3. It reduces sediment buildup on the tank bottom
    4. It protects the steel tank by corroding sacrificially Correct answer.

    Explanation

    An anode rod is more electrochemically active than the steel shell, so it corrodes preferentially and protects the glass lining and exposed steel from attack. Once the rod is consumed, the tank itself begins to corrode. That is why the rod is inspected at servicing intervals and replaced when heavily depleted.

  127. Question 127Water Heaters

    Dielectric unions are installed between copper piping and the steel nipples of a water heater in order to do what?

    1. Allow the piping to be disconnected without draining the tank
    2. Increase the flow rate through the connection
    3. Compensate for thermal expansion of the piping Correct answer.
    4. Provide a dielectric break that prevents galvanic corrosion

    Explanation

    Copper and steel in contact in the presence of water form a galvanic couple, and the steel side corrodes rapidly. A dielectric union places an insulating barrier between the two metals to break that electrical path. Even with the union, the steel nipple itself must be protected internally, usually by a lining or a dielectric-lined nipple.

  128. Question 128Water Heaters

    The discharge pipe from a temperature-and-pressure relief valve on a water heater must be installed so that it does what?

    1. Slopes downward and ends within 6 inches of the floor Correct answer.
    2. Connects to the building drain through a trap
    3. Terminates at least 12 inches above grade outside the building
    4. Is reduced to match the drain pan outlet size

    Explanation

    Relief valve discharge must run full size, slope downward, and terminate in a safe place of disposal such as within about 6 inches of the floor or at an approved exterior location where the pipe end is visible. The pipe must not be trapped, reduced, or connected directly to a drainage system, so any discharge is obvious and no cross-connection is created.

  129. Question 129Water Heaters

    A sediment trap, or drip leg, is installed in the gas piping serving a water heater in order to do what?

    1. Reduce the gas pressure at the burner
    2. Provide a test port for pressure testing the line
    3. Allow condensate to drain from the flue
    4. Trap dirt and debris before it reaches the gas valve Correct answer.

    Explanation

    Utility gas commonly carries pipe scale and dirt that can foul or jam the gas control valve and burner orifices. A sediment trap is a capped nipple installed at the bottom of a tee, downstream of the shutoff valve and as close as practical to the appliance, where debris settles out. Gas pressure reduction is handled by the regulator, not the trap.

  130. Question 130Water Heaters

    A single-wall flue connector from a draft-hood-equipped water heater must pitch upward toward the chimney at a minimum slope of what?

    1. 1/4 inch per foot Correct answer.
    2. 1/8 inch per foot
    3. 1/2 inch per foot
    4. 1 inch per foot

    Explanation

    Vent connectors must rise toward the chimney at not less than 1/4 inch per foot of horizontal run so that flue gases travel upward and condensation drains back toward the appliance. The connector must also be as short and direct as possible and supported against sagging. A flatter slope allows gases to stratify and cool, weakening draft.

  131. Question 131Water Heaters

    A gas-fired water heater without a flammable vapor ignition resistant design is installed in a residential garage. Its ignition source must be elevated at least how far above the floor?

    1. 18 inches Correct answer.
    2. 6 inches
    3. 12 inches
    4. 36 inches

    Explanation

    Gasoline vapors and other flammable liquids are heavier than air and collect near the floor, so an unprotected burner or pilot must be raised at least 18 inches above the garage floor. Water heaters built with a flammable vapor ignition resistant design are exempt from the elevation requirement but must still be protected from physical damage. The elevation applies to the ignition source, not to the tank bottom.

  132. Question 132Water Heaters

    A thermal expansion tank is needed on a residential water heating system whenever which condition exists?

    1. The heater sits on an upper floor
    2. The water supply is high in minerals
    3. The heater has a glass-lined tank
    4. A backflow preventer or PRV creates a closed system Correct answer.

    Explanation

    When a check valve, backflow preventer, or pressure-reducing valve isolates the water heater from the public main, heated water has nowhere to expand. The resulting pressure rise can lift the relief valve repeatedly and damage the tank or fixtures, so a closed system requires an expansion tank or other approved means of controlling expansion. Heater location, lining type, and water quality do not create a closed system.

  133. Question 133Water Heaters

    On a storage-type water heater, where must the temperature-and-pressure relief valve be installed?

    1. Anywhere on the shell that remains accessible
    2. In the top 6 inches of the tank, on the hot outlet side Correct answer.
    3. On the cold inlet, downstream of the shutoff valve
    4. On the drain valve at the bottom of the tank

    Explanation

    The relief valve must sense the hottest water and be located in the top 6 inches of the tank, typically on the hot outlet tapping. It must be installed directly on the tank or on a fitting with no intervening valve or plug, and it must remain accessible for testing. Mounting it at the bottom or on the cold side would delay its response to overheating.

  134. Question 134Water Heaters

    What component in a dedicated hot water recirculation return line keeps hot water from migrating into the return by gravity when the pump is off?

    1. An expansion tank on the return line
    2. A pressure-reducing valve on the return
    3. A check valve in the return line Correct answer.
    4. A vacuum breaker at the farthest fixture

    Explanation

    A check valve, or a specially designed recirculation fitting, keeps the return line from acting as a thermal siphon when the pump stops. Without it, hot water would keep drifting up the return and the loop would waste energy. The check valve also prevents backward flow into the cold side of the system.

  135. Question 135Water Heaters

    Where seismic strapping of water heaters is required, the tank is normally secured with two straps placed in which locations?

    1. One at the top and one at the bottom of the tank
    2. Around the middle third and the base
    3. Both in the upper third of the tank
    4. In the upper third and the lower third of the tank Correct answer.

    Explanation

    The standard arrangement uses an upper strap in the top third and a lower strap in the bottom third of the tank, anchored to the structure with the specified fasteners. Spacing the straps this way resists both tipping and sliding during ground motion. The lower strap must sit above the controls so it does not damage them.

  136. Question 136Water Heaters

    When a potable water heater also serves as the heat source for a space heating system, what safeguard is required at the connection between the two?

    1. A separate relief valve on the heating loop only
    2. A double-wall heat exchanger between the potable water and the heating medium Correct answer.
    3. A check valve on the domestic cold water inlet
    4. A vacuum breaker on the heating loop

    Explanation

    Heating system water is nonpotable and may contain treatment chemicals, so it must be separated from the domestic supply by a double-wall heat exchanger or an equivalent approved backflow assembly. This arrangement prevents contamination of the potable water if a leak or pressure reversal occurs. A single check valve is not an adequate separation for this hazard.

  137. Question 137Water Heaters

    A water heater is installed in a location where a leak from the tank or fittings could cause damage. What must the required drain pan do?

    1. Be welded watertight at every seam
    2. Discharge into the relief valve drain line above the floor flange
    3. Be at least 4 inches deep with a sealed cover
    4. Drain by gravity to an approved location through a pipe at least 3/4 inch in size Correct answer.

    Explanation

    The pan must be at least 1-1/2 inches deep with a minimum 3/4-inch drain that carries leakage by gravity to an approved point of disposal. It must not be connected to the relief valve discharge or to a drainage system in a way that creates a cross-connection. The purpose is to route a leak to a safe, visible location rather than let it damage the building.

  138. Question 138Water Heaters

    A gas water heater has a rated input of 40,000 Btu/hr and an efficiency of 80 percent. It heats incoming water at 50°F to a stored temperature of 140°F. What is its approximate recovery rate?

    1. 43 gph Correct answer.
    2. 34 gph
    3. 53 gph
    4. 32 gph

    Explanation

    Recovery rate equals usable input divided by the weight of a gallon of water times the temperature rise: (40,000 × 0.80) ÷ (8.33 × 90) ≈ 42.7 gallons per hour. The temperature rise is the difference between the incoming and stored temperatures, 90°F here. Using the full input without the efficiency allowance overstates the recovery.

  139. Question 139Water Heaters

    A 40,000 Btu/hr water heater is installed in a 400-cubic-foot closet with two permanent openings to an adjoining interior space. What is the minimum required free area of each opening?

    1. 40 square inches Correct answer.
    2. 20 square inches
    3. 10 square inches
    4. 80 square inches

    Explanation

    A 400-cubic-foot closet is a confined space for a 40,000 Btu/hr appliance, since the threshold is 50 cubic feet per 1,000 Btu/hr, or 2,000 cubic feet here. Using the two-permanent-opening method with interior air, each opening must have at least 1 square inch of free area per 1,000 Btu/hr of total input, so each opening needs 40 square inches. Both the top and bottom openings are sized on the full input, not half of it.

  140. Question 140Fuel Gas Piping and Venting

    Where must a sediment trap be installed on a gas piping system serving an appliance?

    1. On the appliance manifold, downstream of the burner controls
    2. At the outlet of the gas meter, before any other valves or fittings
    3. Downstream of the appliance shutoff valve, as close to the appliance inlet as practical Correct answer.
    4. Upstream of the appliance shutoff valve, at the end of the longest main run

    Explanation

    A sediment trap (drip leg) is required at the inlet of each appliance unless the appliance has a trap integral with it. It is installed downstream of the appliance shutoff valve and as close to the appliance inlet as practical so scale and debris settle out before reaching the controls.

  141. Question 141Fuel Gas Piping and Venting

    Which statement about using a metallic gas piping system as an electrical grounding electrode is correct?

    1. It is permitted where the buried piping is at least 12 inches deep
    2. It is permitted where a 6 AWG copper bonding jumper is installed
    3. It is prohibited; gas piping may not serve as a grounding electrode Correct answer.
    4. It is permitted only where corrugated stainless steel tubing is used

    Explanation

    Metallic gas piping must be electrically continuous and bonded to the grounding electrode system, but the gas piping itself is never permitted to act as a grounding electrode for the electrical system. Bonding and grounding are separate functions.

  142. Question 142Fuel Gas Piping and Venting

    A vent connector for a naturally drafting appliance must slope upward toward the vent at a minimum rate of:

    1. 1/16 inch per foot of run
    2. 1/8 inch per foot of run
    3. 1/4 inch per foot of run Correct answer.
    4. 1/2 inch per foot of run

    Explanation

    Vent connectors must slope upward toward the chimney or vent at not less than 1/4 inch per foot of horizontal run. The slope keeps flue products moving toward the vent and allows any condensate to drain in the intended direction.

  143. Question 143Fuel Gas Piping and Venting

    What is the maximum permitted length of a listed gas appliance connector?

    1. 3 feet
    2. 9 feet
    3. 6 feet Correct answer.
    4. 12 feet

    Explanation

    Listed appliance connectors are limited to a maximum length of 6 feet. They must also be installed without concealment and may not pass through walls, floors, or ceilings.

  144. Question 144Fuel Gas Piping and Venting

    Which test medium is prohibited when pressure testing a gas piping system?

    1. Dry nitrogen
    2. Carbon dioxide
    3. Compressed air
    4. Oxygen Correct answer.

    Explanation

    Piping is tested with air, nitrogen, carbon dioxide, or another inert gas. Oxygen is prohibited because it vigorously supports combustion and can ignite residual gas, oil, or thread compound inside the piping.

  145. Question 145Fuel Gas Piping and Venting

    A gas vent passing through a roof must extend at least:

    1. Two feet above the highest point of the roof, regardless of nearby walls or parapets
    2. Four feet above the roof penetration and level with the nearest chimney top
    3. Three feet above the roof penetration and two feet above anything within ten feet Correct answer.
    4. One foot above the roof penetration and four feet from any window or intake

    Explanation

    A vent must extend at least 3 feet above the highest point where it passes through the roof and at least 2 feet above any portion of the building within 10 feet horizontally. This keeps flue products out of the turbulent eddy zone at the roof surface.

  146. Question 146Fuel Gas Piping and Venting

    A gas range is installed in a kitchen. Where must its individual appliance shutoff valve be located?

    1. Not more than 10 feet from the appliance, in an accessible location
    2. In the same room as the appliance, not more than 6 feet away Correct answer.
    3. In the basement at the point where the branch leaves the main
    4. Directly on the appliance manifold, ahead of the regulator

    Explanation

    Each appliance must have a shutoff valve separate from the appliance, located in the same room, not more than 6 feet from the appliance, and readily accessible. The valve must also be of the indicating type so its open or closed position is obvious.

  147. Question 147Fuel Gas Piping and Venting

    When making up threaded gas piping joints, threads shall be cut so that:

    1. Six exposed threads are provided to allow alignment
    2. At least four threads remain exposed for inspection
    3. No threads remain exposed once the joint is wrench-tight
    4. Not more than three threads remain exposed after tightening Correct answer.

    Explanation

    Threads cut too deep thin the pipe wall and reduce the strength of the joint, so the code limits exposed threads to a maximum of three after make-up. Approved joint compound is applied to the male threads only.

  148. Question 148Fuel Gas Piping and Venting

    Using the standard method with indoor air from adjacent spaces, the required volume for a space containing a 100,000 Btu/hr appliance is:

    1. 500 cubic feet
    2. 1,000 cubic feet
    3. 2,500 cubic feet
    4. 5,000 cubic feet Correct answer.

    Explanation

    The standard method allows 50 cubic feet of space volume for each 1,000 Btu/hr of total appliance input. For 100,000 Btu/hr, 100 times 50 cubic feet gives 5,000 cubic feet.

  149. Question 149Fuel Gas Piping and Venting

    Combustion air is supplied to an appliance enclosure through two permanent openings into an adjacent space. How must those openings be arranged?

    1. Both openings located within 18 inches of the enclosure floor
    2. Both openings located in the upper half of the enclosure wall
    3. One within 6 inches of the ceiling and one at mid-height of the wall
    4. One within 12 inches of the top and one within 12 inches of the bottom Correct answer.

    Explanation

    Two permanent openings are required, one commencing within 12 inches of the top of the enclosure and one within 12 inches of the bottom. This arrangement allows air to enter low and relief openings to vent high as the space heats.

  150. Question 150Fuel Gas Piping and Venting

    A listed Type B double-wall gas vent is installed through a closet. Its minimum clearance to combustible construction is typically:

    1. 1 inch Correct answer.
    2. 3 inches
    3. 2 inches
    4. 6 inches

    Explanation

    Listed Type B double-wall vents are listed for a 1-inch clearance to combustibles, which is why the listing and the manufacturer's instructions must be followed. Single-wall vent connectors, by contrast, require 6 inches of clearance.

  151. Question 151Fuel Gas Piping and Venting

    A natural gas piping system designed to operate at 7 inches water column shall be tested at a minimum pressure and duration of:

    1. 1.5 psi for 5 minutes
    2. The operating pressure for 15 minutes
    3. 10 psi for 30 minutes
    4. 3 psi for 10 minutes Correct answer.

    Explanation

    The test pressure may not be less than 1.5 times the proposed maximum working pressure and never less than 3 psi. For test pressures between 3 and 20 psi, the system is held for at least 10 minutes.

  152. Question 152Fuel Gas Piping and Venting

    A gas pressure regulator vent serving an appliance shall terminate:

    1. Outdoors, protected against the entry of water and insects Correct answer.
    2. Inside the appliance cabinet near the burner air intake
    3. Below the regulator, inside a capped drip leg
    4. In the return air plenum of the central heating system

    Explanation

    Regulator vents must discharge outdoors in a location where gas cannot accumulate or re-enter the building, and the outlet must be protected with a screen or weatherproof vent cap. Blocked or improperly terminated vents can cause regulator malfunction and hazardous gas release.

  153. Question 153Fuel Gas Piping and Venting

    How must a vent connector between a draft hood equipped appliance and a vertical vent be sized?

    1. By appliance input alone, with no reference to the vent size
    2. Two nominal sizes larger than the vent to reduce back pressure
    3. Not smaller than the draft hood outlet and not smaller than the vent it enters Correct answer.
    4. One nominal size smaller than the draft hood outlet to increase velocity

    Explanation

    A vent connector may not be smaller than the draft hood outlet or flue collar of the appliance, and it may not be smaller than the vent it connects to. Reducing the connector size restricts flow and can cause spillage of flue gases.

  154. Question 154Fuel Gas Piping and Venting

    A gas-fired furnace is to be vented. Which of the following connections is prohibited?

    1. Into a chimney flue that also serves a solid-fuel-burning fireplace Correct answer.
    2. Into a factory-built chimney listed for use with the appliance
    3. Into a lined masonry chimney serving only that furnace
    4. Into a listed Type B vent sized for the appliance input

    Explanation

    A gas vent may not be connected to a chimney flue that serves a solid-fuel appliance or an open fireplace. Solid-fuel flues are subject to different draft, temperature, and creosote conditions that can cause flue gas spillage or unsafe chimney operation.

  155. Question 155Fuel Gas Piping and Venting

    Corrugated stainless steel tubing gas piping must be bonded to the electrical grounding system with a conductor not smaller than:

    1. 6 AWG copper Correct answer.
    2. 14 AWG copper
    3. 12 AWG copper
    4. 8 AWG aluminum

    Explanation

    The bonding jumper for gas piping must be at least 6 AWG copper (or 4 AWG aluminum) and must be connected in accordance with the listing and the manufacturer's instructions. Bonding reduces the risk of lightning-induced arcing damaging the tubing.

  156. Question 156Fuel Gas Piping and Venting

    A Category IV condensing appliance must be vented with:

    1. A single-wall connector sloping up to a masonry chimney
    2. A Type B double-wall vent with a draft hood at the outlet
    3. A listed positive-pressure vent with condensate drainage Correct answer.
    4. A vent connector fitted with a barometric draft regulator

    Explanation

    Category IV appliances operate with positive vent pressure and produce acidic condensate, so the vent must be listed for that service, sealed, and arranged to drain condensate per the manufacturer's instructions. Draft hoods and barometric regulators are for naturally drafting appliances.

  157. Question 157Fuel Gas Piping and Venting

    Two draft hood appliances share a common vertical vent. Which connector arrangement is required?

    1. The larger connector enters above the smaller, both sloping up
    2. The smaller connector enters above the larger, both sloping up Correct answer.
    3. The smaller connector enters below the larger, with a baffle at the fitting
    4. Both connectors enter at the same level from opposite sides

    Explanation

    The connector from the smaller appliance should enter the common vent above the connector from the larger appliance, with both connectors sloping upward to the vent. This reduces the chance that flue gases from the larger appliance spill out of the smaller appliance's draft hood.

  158. Question 158Fuel Gas Piping and Venting

    An existing 1/2-inch natural gas branch serving a water heater is extended to supply an additional 50,000 Btu/hr appliance. What is the correct approach?

    1. Keep the 1/2-inch branch whenever the total run is under 60 feet
    2. Reduce the water heater orifice to offset the added input
    3. Resize the branch using total connected load and longest run length Correct answer.
    4. Tee off a second 1/2-inch branch from the same fitting to split the load

    Explanation

    Pipe sizing tables are based on the total connected demand and the longest length from the meter to the farthest outlet. Adding load to an existing size can exceed the table capacity, so the branch must be recalculated with the new total demand and the revised longest run.

  159. Question 159Fuel Gas Piping and Venting

    Combustion air is supplied to a confined space through two horizontal ducts that open outdoors. Each duct opening must have a free area of at least:

    1. 1 square inch per 4,000 Btu/hr
    2. 1 square inch per 5,000 Btu/hr
    3. 1 square inch per 2,000 Btu/hr Correct answer.
    4. 1 square inch per 1,000 Btu/hr

    Explanation

    When combustion air reaches a confined space through two horizontal ducts opening outdoors, each opening must have at least 1 square inch of free area per 2,000 Btu/hr of total input. Vertical openings opening directly outdoors use 1 square inch per 4,000 Btu/hr.

  160. Question 160Safety, Tools, and Jobsite Practices

    OSHA requires excavated spoil and equipment to be kept at what minimum distance back from the edge of a trench?

    1. 4 feet
    2. 6 feet
    3. 2 feet Correct answer.
    4. 1 foot

    Explanation

    Excavated material, tools, and equipment must be kept at least 2 feet from the edge of an excavation. Spoil piled closer acts as a surcharge load on the trench wall and can also fall back onto workers below.

  161. Question 161Safety, Tools, and Jobsite Practices

    An extension ladder must be set so the base is how far from the wall it leans against?

    1. The full working length
    2. One-quarter of the working length Correct answer.
    3. One-eighth of the working length
    4. One-half of the working length

    Explanation

    The 4-to-1 rule places the base of an extension ladder one-quarter of its working length out from the wall. This gives a safe climbing angle of roughly 75 degrees.

  162. Question 162Safety, Tools, and Jobsite Practices

    What is the minimum eye protection for operating a power pipe threading machine?

    1. Safety glasses with side shields Correct answer.
    2. A face shield with no eye covering beneath
    3. Prescription eyeglasses alone
    4. Sunglasses

    Explanation

    Safety glasses with side shields are the minimum eye protection for machine operations that throw chips, oil, and cuttings. A face shield may be added over them for extra coverage.

  163. Question 163Safety, Tools, and Jobsite Practices

    How must a cord-and-plug portable electric tool be powered when used on a construction site?

    1. Connected to a GFCI-protected receptacle Correct answer.
    2. Powered from a generator with no grounding
    3. Connected through a standard extension cord
    4. Plugged directly into a temporary panel with no protection

    Explanation

    Temporary receptacles on construction sites must have ground-fault circuit interrupter protection, or the employer must run an assured equipment grounding conductor program. GFCI protection is what limits injury if a tool or cord faults.

  164. Question 164Safety, Tools, and Jobsite Practices

    In what order should a confined space atmosphere be tested before entry?

    1. Combustible gas, then oxygen, then toxic gases
    2. Toxic gases, then oxygen, then combustible gas
    3. Combustible gas, then toxic gases, then oxygen
    4. Oxygen, then combustible gas, then toxic gases Correct answer.

    Explanation

    Test for oxygen content first, then for combustible gas, then for toxic gases. Oxygen is tested first because both combustible meters and human tolerance depend on a valid oxygen reading, and many combustible sensors give false readings in oxygen-deficient air.

  165. Question 165Safety, Tools, and Jobsite Practices

    Combustible material near a soldering or brazing operation must be moved or protected if it is within what distance of the work?

    1. 10 feet
    2. 50 feet
    3. 35 feet Correct answer.
    4. 75 feet

    Explanation

    Hot work rules require combustibles within 35 feet of the operation to be relocated or protected with a fire-resistant covering or shield. A fire watch is then maintained during the work and for the required period afterward.

  166. Question 166Safety, Tools, and Jobsite Practices

    Who is permitted to remove a lock and tag from an energy-isolating device?

    1. The crew supervisor
    2. The person who applied the lock Correct answer.
    3. The general contractor's safety officer
    4. Any journeyman on the crew

    Explanation

    Under lockout/tagout, only the authorized employee who applied the lock and tag may remove them. If that employee is unavailable, removal must follow the employer's specific documented procedure, which includes attempting to contact the lock owner.

  167. Question 167Safety, Tools, and Jobsite Practices

    A plumber must cut openings in a concrete wall indoors. Which practice best controls crystalline silica exposure?

    1. Cut dry but keep other workers away from the area
    2. Wear a disposable dust mask and cut dry
    3. Cut dry outdoors because the dust disperses quickly
    4. Wet-cut or use dust collection plus a respirator Correct answer.

    Explanation

    Silica dust is controlled at the source by wet cutting or on-tool dust collection, with respiratory protection as needed for the exposure level. Engineering controls come first because they keep dust out of the air rather than relying on the wearer.

  168. Question 168Safety, Tools, and Jobsite Practices

    What is the required height of the top guardrail on a supported scaffold?

    1. 42 inches Correct answer.
    2. 48 inches
    3. 30 inches
    4. 36 inches

    Explanation

    The top rail of a scaffold guardrail system is installed at 42 inches, with a permitted range of 38 to 45 inches, plus a midrail and toe board. The midrail is set roughly halfway between the platform and the top rail.

  169. Question 169Safety, Tools, and Jobsite Practices

    How should a plumber check a newly made gas piping joint for leaks?

    1. Pressurize the line with oxygen and listen for leaks
    2. Hold a lit match near the joint and watch the flame
    3. Smell the joint closely to detect the odorant
    4. Apply soapy water and watch for bubbles Correct answer.

    Explanation

    Leak checks are made with a nonflammable soap-and-water solution or an approved leak detector applied to the joint while the line is under test pressure. Bubbles indicate escaping gas.

  170. Question 170Safety, Tools, and Jobsite Practices

    How should a plumber protect a wood floor joist that is close to a joint being soldered?

    1. Shut the torch off between every pass of the solder
    2. Wet the combustible surface down before soldering
    3. Shield the surface with a flame-resistant pad Correct answer.
    4. Open a window and keep working at the same spot

    Explanation

    A flame-resistant heat shield or pad placed between the flame and the combustible material blocks radiant heat and sparks. Wetting wood gives only temporary protection, and the torch stays lit throughout the joint.

  171. Question 171Safety, Tools, and Jobsite Practices

    A pipe wrench will not break a fitting loose. Which practice is acceptable?

    1. Switch to a larger wrench with a longer handle Correct answer.
    2. Strike the handle with a hammer while it is under load
    3. Stand on the wrench handle to add body weight
    4. Slip a length of pipe over the handle to increase leverage

    Explanation

    When a wrench lacks leverage, use a properly sized wrench with a longer handle so the tool is loaded as designed. Extending a handle with pipe or standing on it overloads the jaws and frame and can cause sudden failure.

  172. Question 172Safety, Tools, and Jobsite Practices

    What is the maximum allowable slope for a simple slope excavation in Type C soil?

    1. 1 horizontal to 1 vertical
    2. 3 horizontal to 1 vertical
    3. ¾ horizontal to 1 vertical
    4. 1½ horizontal to 1 vertical Correct answer.

    Explanation

    Type C soil is the least stable classification and requires a slope no steeper than 1½ horizontal to 1 vertical, about 34 degrees. Type B allows 1 to 1 and Type A allows ¾ to 1.

  173. Question 173Safety, Tools, and Jobsite Practices

    A crew runs a gas-powered concrete saw inside a basement to cut floor openings. What is the principal atmospheric hazard?

    1. Explosive accumulation of methane from the floor slab
    2. Nitrogen asphyxiation rising from the soil
    3. Carbon monoxide buildup from the saw's exhaust Correct answer.
    4. Oxygen enrichment of the basement air

    Explanation

    Gasoline engines produce carbon monoxide, an odorless gas that accumulates quickly in a closed space and displaces oxygen in the blood. Fuel-powered equipment should be run outside or the space ventilated and monitored for CO.

  174. Question 174Safety, Tools, and Jobsite Practices

    A manhole tested acceptable two hours ago, and flow has since begun running through the sewer. What should the crew do before entry?

    1. Ventilate for five minutes and enter without testing
    2. Enter, since the earlier test is still valid for the shift
    3. Enter with a dust mask because the air tested clean
    4. Retest the atmosphere; conditions can change Correct answer.

    Explanation

    Confined space atmospheres can change as flows, biological activity, or other work alters conditions, so the space must be retested before entry and monitored while occupied. A clean reading from hours earlier proves nothing about the present air.

  175. Question 175Safety, Tools, and Jobsite Practices

    A solvent splashes into a plumber's eye. What is the correct first response?

    1. Rub the eye to work the chemical out
    2. Flush for 30 seconds and return to work
    3. Flush with water for at least 15 minutes, then get care Correct answer.
    4. Neutralize the chemical with a special eyewash solution

    Explanation

    Chemical eye exposures are flushed with clean water or an eyewash station for at least 15 minutes, and the worker is then evaluated by medical personnel. Prompt, prolonged flushing limits tissue damage.

  176. Question 176Plan Reading, Math, and System Layout

    A floor plan is drawn at a scale of 1/4 inch = 1 foot. A wall-to-wall piping run measures 3 1/2 inches on the drawing. What is the actual length?

    1. 14 ft 0 in Correct answer.
    2. 12 ft 0 in
    3. 16 ft 0 in
    4. 10 ft 6 in

    Explanation

    At 1/4 inch = 1 foot, each 1/4 inch on paper equals 1 foot in the building, so 1 inch on paper represents 4 feet. Multiply 3.5 inches by 4 to get 14 feet.

  177. Question 177Plan Reading, Math, and System Layout

    What information does a fixture schedule on a plumbing plan set provide?

    1. the building's zoning classification
    2. the soil percolation test results
    3. fixture types, sizes, and quantities Correct answer.
    4. the contractor's submitted bid prices

    Explanation

    A fixture schedule is a table listing each fixture by type with its quantity, model, and rough-in connection sizes. It is used for material takeoff and for coordinating rough-in dimensions with the plan.

  178. Question 178Plan Reading, Math, and System Layout

    A 4-inch building drain is laid at a slope of 1/4 inch per foot. What is the total fall over a 20-foot horizontal run?

    1. 4 inches
    2. 2 inches
    3. 5 inches Correct answer.
    4. 10 inches

    Explanation

    Fall equals slope multiplied by horizontal run: 1/4 inch per foot times 20 feet equals 5 inches of total fall. Slope is always applied per foot of horizontal distance, not along the pipe.

  179. Question 179Plan Reading, Math, and System Layout

    On a plumbing floor plan legend, which abbreviation identifies a floor drain?

    1. WH
    2. CO
    3. WC
    4. FD Correct answer.

    Explanation

    FD is the standard plan abbreviation for floor drain. Related legend entries use WC for water closet, CO for cleanout, and WH for water heater.

  180. Question 180Plan Reading, Math, and System Layout

    What does the north arrow on a plumbing floor plan indicate?

    1. the depth of the local frost line
    2. the flow direction of the drain
    3. the direction of plan north Correct answer.
    4. the location of the water service

    Explanation

    The north arrow orients the drawing so the building and its underground utilities can be related to the site. Pipe flow direction is shown with slope arrows or notes, not with the north arrow.

  181. Question 181Plan Reading, Math, and System Layout

    On a plumbing isometric riser diagram, what do the lines drawn vertically represent?

    1. horizontal branches below the floor
    2. vertical piping runs Correct answer.
    3. fixture supply stop locations
    4. underground building drains

    Explanation

    An isometric riser diagram uses vertical lines for vertical pipe, horizontal lines for horizontal runs, and 45-degree lines to show depth and offsets. This lets the reader see the vertical relationships between floors at a glance.

  182. Question 182Plan Reading, Math, and System Layout

    How is the developed length of a piping run determined for sizing calculations?

    1. along the pipe centerline including fittings Correct answer.
    2. as the straight-line distance between endpoints
    3. between the two farthest fixtures only
    4. as the horizontal distance shown on the plan

    Explanation

    Developed length is measured along the centerline of the pipe and adds the equivalent length of fittings and bends. Friction loss occurs through fittings as well as straight pipe, so the developed length is what the sizing tables require.

  183. Question 183Plan Reading, Math, and System Layout

    A pipe offsets at 45 degrees with a rise of 12 inches. What is the travel length of the offset?

    1. about 15 inches
    2. about 17 inches Correct answer.
    3. about 12 inches
    4. about 13 1/2 inches

    Explanation

    For a 45-degree offset, travel equals offset multiplied by 1.414. Here 12 inches times 1.414 is about 17 inches of pipe between the two fittings.

  184. Question 184Plan Reading, Math, and System Layout

    Why are water supply fixture units converted to probable demand in gallons per minute when sizing pipe?

    1. demand reflects probable simultaneous use Correct answer.
    2. each fixture unit equals one gallon per minute
    3. pressure and flow are unrelated to fixture units
    4. code requires a one-to-one conversion

    Explanation

    Fixture units are a weighting of fixtures by their load, and the conversion curve estimates how much demand is likely to occur at the same time. Because not every fixture operates simultaneously, the probable demand is less than the sum of the individual fixture flows.

  185. Question 185Plan Reading, Math, and System Layout

    For a fixed flow rate, what happens when a water distribution pipe is increased in diameter?

    1. velocity and friction loss increase
    2. pressure at the source increases
    3. the developed length of the system decreases
    4. velocity and friction loss decrease Correct answer.

    Explanation

    A larger pipe holds the same flow at a lower velocity, and friction loss falls sharply as velocity drops. The result is more pressure available at the fixtures served by that pipe.

  186. Question 186Plan Reading, Math, and System Layout

    An individual vent serves a fixture whose drain is 3 inches in diameter. What is the minimum vent size allowed?

    1. 3 inches
    2. 1 1/2 inches Correct answer.
    3. 2 inches
    4. 1 1/4 inches

    Explanation

    An individual vent must be at least 1 1/4 inch in diameter and never smaller than one-half the diameter of the drain it serves. One-half of a 3-inch drain is 1 1/2 inches, so that dimension controls.

  187. Question 187Plan Reading, Math, and System Layout

    A 4-inch building sewer leaves the building 2 feet below grade and runs 60 feet to the main at a slope of 1/4 inch per foot. What is the invert depth at the main?

    1. 2 ft 10 in
    2. 3 ft 0 in
    3. 2 ft 5 in
    4. 3 ft 3 in Correct answer.

    Explanation

    Fall equals 1/4 inch per foot times 60 feet, or 15 inches, which is 1 foot 3 inches. Adding that to the 2-foot depth at the building gives 3 feet 3 inches.

  188. Question 188Plan Reading, Math, and System Layout

    Roof drain and leader capacity on a commercial building is selected from tables based on which two factors?

    1. number of fixtures served
    2. water service pressure and pipe size
    3. roof area and rainfall intensity Correct answer.
    4. building height and occupancy

    Explanation

    Sizing tables relate the square footage drained to the design rainfall intensity for the location. A larger roof or a higher design rainfall requires larger or more numerous drains and leaders.

  189. Question 189Plan Reading, Math, and System Layout

    Why is the longest run from the gas meter to the farthest appliance used when sizing gas piping?

    1. the longest run uses the largest fittings
    2. short runs must be sized larger for safety
    3. gas meters are sized by run length
    4. the longest run loses the most pressure Correct answer.

    Explanation

    Friction loss accumulates along the entire path, so the longest developed run from the meter to the last appliance has the greatest pressure drop. Sizing that path assures every other branch on the system receives adequate pressure.

  190. Question 190Plan Reading, Math, and System Layout

    A plan shows a fixture rough-in at elevation 102.50 and the building drain invert below it at 98.00. What is the vertical distance between them?

    1. 4 ft 6 in Correct answer.
    2. 4 ft 3 in
    3. 5 ft 0 in
    4. 4 ft 0 in

    Explanation

    Subtract the lower elevation from the higher one: 102.50 minus 98.00 equals 4.50 feet, which is 4 feet 6 inches. Elevations on plans are normally given in decimal feet, so the 0.50 converts to 6 inches.

  191. Question 191Plan Reading, Math, and System Layout

    A drainage line falls 9 inches over a horizontal run of 50 feet. What is the grade in percent?

    1. 1.5 percent Correct answer.
    2. 0.9 percent
    3. 1.35 percent
    4. 1.2 percent

    Explanation

    Convert the fall to feet: 9 inches is 0.75 foot. Grade percent equals fall divided by run times 100, so 0.75 divided by 50 times 100 equals 1.5 percent.

  192. Question 192Plan Reading, Math, and System Layout

    A horizontal drain changes direction using two 45-degree bends separated by a short piece of pipe. What is the total change in direction?

    1. 90 degrees Correct answer.
    2. 22 1/2 degrees
    3. 45 degrees
    4. 60 degrees

    Explanation

    Each 45-degree fitting turns the line 45 degrees, so two of them in series produce a 90-degree change of direction. This combination is commonly used for horizontal offsets because each fitting keeps the change within limits for drainage flow.

  193. Question 193Plan Reading, Math, and System Layout

    Where does the building sewer begin in relation to the building?

    1. at the highest fixture on the system
    2. inside the building at the base of the stack
    3. at the water meter vault
    4. outside the building foundation wall Correct answer.

    Explanation

    The building drain collects the fixtures inside the building and carries the flow to the foundation wall, where it becomes the building sewer. The sewer then runs outside the building to the public sewer or private system.

  194. Question 194Plan Reading, Math, and System Layout

    What information is needed to size a storage-type water heater for a building?

    1. the building's total floor area
    2. peak demand and recovery rate Correct answer.
    3. the number of roof drains
    4. the diameter of the building sewer

    Explanation

    The storage volume and the recovery rate of the heater are matched to the peak hourly hot water demand so the building does not run out during high use. Floor area and drain sizing do not describe hot water use.

  195. Question 195Plan Reading, Math, and System Layout

    A rolling offset has a horizontal offset of 16 inches and a vertical offset of 12 inches. Using 45-degree fittings, what is the travel length?

    1. 24 inches
    2. about 28 1/4 inches Correct answer.
    3. 20 inches
    4. 25 1/2 inches

    Explanation

    The true offset is the diagonal of the two offsets: the square root of 16 squared plus 12 squared equals 20 inches. Travel for 45-degree fittings is the true offset times 1.414, or about 28 1/4 inches.

  196. Question 196Plan Reading, Math, and System Layout

    What primarily determines the maximum allowable length of a fixture trap arm?

    1. the total fixture load of the building
    2. the diameter of the trap arm Correct answer.
    3. the water service pressure
    4. the length of the building sewer

    Explanation

    Trap arm length limits are tabulated by the diameter of the trap arm serving the fixture. A small trap arm that runs too far loses its air space and can self-siphon the trap when the fixture drains.

  197. Question 197Plan Reading, Math, and System Layout

    A fixture is located 30 feet above the water meter, where the static pressure is 60 psi. Ignoring friction, what static pressure is available at the fixture?

    1. 52 psi
    2. 47 psi Correct answer.
    3. 60 psi
    4. 43 psi

    Explanation

    Static pressure drops about 0.433 psi for every foot of elevation gain. Thirty feet costs about 13 psi, so 60 minus 13 leaves about 47 psi at the fixture.

  198. Question 198Plan Reading, Math, and System Layout

    A plan drawn at 1/8 inch = 1 foot shows a piping run measuring 4 5/8 inches. What is the actual length?

    1. 46 ft 3 in
    2. 27 ft 9 in
    3. 37 ft 0 in Correct answer.
    4. 18 ft 6 in

    Explanation

    At 1/8 inch = 1 foot, each eighth of an inch on the drawing equals 1 foot. The measurement 4 5/8 inches contains 37 eighths, so the actual run is 37 feet.

  199. Question 199Plan Reading, Math, and System Layout

    A takeoff shows 6 water closets (6 dfu each), 4 lavatories (1 dfu each), and 4 bathtubs (2 dfu each). What is the total drainage fixture unit load?

    1. 36 dfu
    2. 48 dfu Correct answer.
    3. 28 dfu
    4. 42 dfu

    Explanation

    Water closets contribute 6 times 6, or 36 dfu; lavatories contribute 4 times 1, or 4 dfu; bathtubs contribute 4 times 2, or 8 dfu. Adding them gives a total of 48 drainage fixture units.

Journeyman Plumber flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Authority having jurisdiction
The official or agency that enforces the adopted plumbing code and approves materials, methods, and inspections; local amendments take precedence over the model code text.
Trap seal depth requirement
A fixture trap must hold a liquid seal between 2 and 4 inches deep, measured from the trap weir to the top of the dip, to block sewer gas from entering the building.
Standard drainage slope
Horizontal drainage pipe 2-1/2 inches and smaller must slope at least 1/4 inch per foot, while 3-inch through 6-inch pipe may slope at 1/8 inch per foot.
Drainage fixture unit
A unit expressing the probable discharge rate of a fixture; one drainage fixture unit is about 1 cubic foot per minute, or roughly 7.5 gallons per minute.
Vent terminal above roof
A vent stack must extend at least 6 inches above the roof surface and may need to be enlarged to 2 inches in cold climates to resist frost closure.
Trap arm length limit
The developed length from the trap weir to the vent fitting is limited by pipe size, roughly 5 feet for 1-1/4 inch, 8 feet for 2 inch, and 16 feet for 4 inch pipe.
Minimum vent pipe size
No vent may be smaller than 1-1/4 inches nominal, and a vent must be at least one-half the diameter of the drain it serves.
Cleanout at base of stack
A cleanout is required at the base of every vertical soil or waste stack and at the upper end of each horizontal drainage pipe before it turns downward.
Pressure reducing valve threshold
A pressure-reducing valve is required when supply pressure exceeds 80 psi, and downstream static pressure is limited to 80 psi to protect fixtures and piping.
Water hammer arrestor
A device with a trapped air chamber or piston installed near a quick-closing valve to absorb the pressure surge created when water flow stops abruptly.
Backflow prevention device
A testable assembly or air gap that stops contaminated water from reversing into the potable supply; required at boilers, irrigation, and other cross-connections.
Thermal expansion tank
A closed potable water system with a check valve or backflow preventer needs an expansion tank to absorb the volume increase as water heats, preventing overpressure.
Water closet flush volume
New residential water closets are limited to 1.6 gallons per flush by federal standard, and many current models use only 1.28 gallons per flush.
Showerhead maximum flow
Showerheads are limited to 2.5 gallons per minute at 80 psi, while lavatory and kitchen faucets are commonly limited to 2.2 gallons per minute.
Water closet rough-in clearance
A water closet needs at least 15 inches from its centerline to any side wall or partition and at least 21 inches of clear space in front of the bowl.
Urinal flush volume
Urinals are limited to 1.0 gallon per flush; waterless urinals rely on a liquid seal cartridge and require special maintenance and drain line provisions.
T&P relief valve setting
A temperature and pressure relief valve on a storage water heater is typically rated 150 psi and 210 degrees F and is installed in the top 6 inches of the tank.
Relief valve discharge pipe
The discharge pipe must be full size, flow by gravity, have no valves or traps, and terminate within 6 inches of the floor or outside the building.
Water heater recovery rate
Recovery in gallons per hour equals input BTU per hour times efficiency divided by 8.33 times the temperature rise; a 40,000 BTU unit at 80 percent and 90 degrees rise gives about 42 gph.
Gas water heater in garage
A gas-fired water heater installed in a garage must have its ignition source elevated at least 18 inches above the floor to avoid igniting gasoline vapors.
Gas sediment trap
A drip leg or sediment trap is installed downstream of the appliance shutoff valve and as close as practicable to the appliance inlet to catch dirt and pipe dope.
Gas appliance shutoff valve
A manual shutoff valve must be installed in the same room as the appliance and within 6 feet of it, upstream of the sediment trap and connector.
Combustion air unconfined space
An unconfined space needs about 50 cubic feet of volume per 1,000 BTU per hour of input, or 1 square inch of free grille area per 1,000 BTU per hour.
CSST bonding requirement
Corrugated stainless steel tubing gas piping must be bonded to the grounding electrode system with a minimum 6 AWG copper conductor at the manifold or as listed.
Trench protective system threshold
A protective system such as sloping, shoring, or a trench box is required for any excavation 5 feet deep or greater, unless the material is solid rock.
Ladder four to one rule
A portable ladder is set with its base 1 foot out from the wall for every 4 feet of working height and extends 3 feet above the landing surface.
Call before you dig
The 811 notification service must be contacted before excavation so underground utilities can be located and marked, typically two to three working days ahead.
Flare fitting pipe dope
Pipe dope or thread sealant is never applied to the sealing surfaces of flare or compression fittings; it is used only on tapered pipe threads.
Reading drawing scale
At a scale of 1/4 inch equals 1 foot, one inch on the drawing represents 4 feet in the field, so measured drawing distance is multiplied by 4.
45 degree offset travel
For a 45-degree offset, travel equals offset times 1.414, and the offset equals travel times 0.707 when the diagonal run between fittings is known.
Static head to pressure
Each foot of water column elevation produces about 0.433 psi, so 1 psi equals 2.31 feet of head and 10 feet of rise adds about 4.33 psi.
Pipe volume to gallons
One gallon holds 231 cubic inches, so pipe volume per foot in gallons equals pi times the inside radius squared times 12, divided by 231.

Journeyman Plumber study guide

Plumbing Code and Regulations

You cannot plumb legally from memory of a model code; you must know which document your authority having jurisdiction (AHJ) has adopted and in what edition. The three model plumbing codes in U.S. use are the International Plumbing Code (IPC), the Uniform Plumbing Code (UPC), and the National Standard Plumbing Code (NSPC). Each is amended locally, so a dimension that is correct in one city can be wrong thirty miles away. Questions built on 'the code' usually assume the model text, but a question that names a jurisdiction is testing whether you read the adoption clause.

Know the hierarchy of authority: the adopted code and local amendments first, then the standards the code references (ASME, ASTM, ASSE, NSF), then the manufacturer's listed installation instructions, which are enforceable because the listing is what makes the product legal. When two requirements conflict, the more restrictive governs; when a manufacturer is stricter than the code, follow the manufacturer.

The administrative half of the code is heavily tested: when a permit is required, who may pull it, what must appear on the drawings, the sequence of rough-in, top-out, and final inspections, and the water and gas tests performed before concealment. Definitions matter, and questions love the difference between a mandatory 'shall,' an advisory 'should,' a recommended practice, and a manufacturer's recommendation.

Worked example: a clearance is given as 1/4 in per foot of run, and you must state the drop over 12 ft in millimeters. Drop = 0.25 x 12 = 3 in; 3 x 25.4 = 76 mm. Convert first, round last, and confirm whether the answer options are inches or millimeters.

Drainage, Waste, and Vent Systems

The DWV system does three jobs: carry waste, keep sewer gas out of the building, and protect trap seals. Nearly every exam question traces back to one of those.

Drainage is sized by fixture units (f.u.), not gallons. A private bathroom group is roughly 5 to 6 f.u.; a water closet about 3 f.u. public and 2.5 to 3 private; a lavatory 1; a bathtub or shower 2; a kitchen sink or clothes washer 2. Slope is 1/4 in per foot for 2-1/2 in and smaller and 1/8 in per foot for 3 in and larger; steeper is legal, but the minimum is not negotiable under a slab. Use wyes and 45s for horizontal-to-vertical changes, never a santee on its back or on a horizontal drain, no reducing fittings in the direction of flow, no double trapping, no S-traps, and no crown venting.

Every trap needs a vent. The trap arm between trap weir and vent is limited by size (commonly 5 ft for 1-1/4 in, 6 ft for 1-1/2 in, 8 ft for 2 in) and must rise, not drop, to the vent. A vent must rise at least 6 in above the flood level rim before it offsets. Terminals generally finish at least 6 in above the roof (a foot or more under some codes), at least 10 ft horizontally from windows, doors, and air intakes, and 2 ft above anything within 10 ft.

Worked example: a 4 in building drain runs 60 ft at 1/8 in per foot. Fall = 60 x 0.125 = 7.5 in, so the downstream invert is 7-1/2 in lower than the upstream invert.

Water Supply and Distribution

Water supply questions test pressure more than pipe. Three ideas anchor most of them: 0.433 psi per foot of elevation (the weight of a column of water), the minimum residual pressure fixtures need, and the maximum static pressure above which you must protect the system.

Typical design targets: about 8 psi flowing for tank-type water closets, roughly 15 to 20 psi flowing for flushometer valves, and a service that lands near 50 to 60 psi. A pressure-reducing valve is generally required when static pressure exceeds 80 psi. Once you add a PRV, a check valve, or a backflow preventer, the system becomes closed, and thermal expansion needs a tank.

Sizing uses water supply fixture units (WSFU) converted to gallons per minute through the Hunter curves, and the curve differs for flush tanks and flushometers, a classic trap. Add the fixtures, look up demand, then select pipe from the table using developed length (measured length plus a fitting allowance, often roughly 50 percent) and available pressure after subtracting elevation and meter losses.

Backflow protection is guaranteed material: air gap (best), reduced-pressure zone assembly (RPZ), double check valve assembly (DCVA), pressure vacuum breaker (PVB), and atmospheric vacuum breaker (AVB). High hazard demands an air gap or an RPZ.

Worked example: a meter reads 80 psi and the highest fixture is 30 ft above it. Static pressure there is 80 minus (30 x 0.433) = 80 minus 13 = 67 psi, before any friction loss.

Plumbing Fixtures and Appliances

Fixture questions blend code tables, clearances, and water conservation limits. Know the standard maxima: 1.6 gallons per flush for water closets (1.28 for WaterSense-labeled units, frequently required by local amendment), 1.0 gpf urinals, 2.2 gpm lavatory and kitchen faucets, and 2.5 gpm showerheads at 80 psi. A question showing a fixture that exceeds these limits is asking you to flag a violation.

Each fixture needs a trap, a trap seal of 2 to 4 in, and protection from backflow, either an air gap of at least twice the effective pipe diameter at a receptor or an indirect waste where food or sterilized equipment is involved. Floor drains in mechanical rooms and kitchens need trap primers so the seal does not evaporate.

Clearances and accessibility are high-yield. A water closet needs 15 in from centerline to any side wall and a 30 in wide space, with roughly 21 to 24 in clear in front. ADA work sets the lavatory rim at 34 in maximum, knee clearance 27 in high by 30 in wide, grab bars 33 to 36 in above the floor, and controls within a 15 to 48 in reach range.

Fixture counts come from occupant load and occupancy classification: compute total occupants, split by sex where required, then divide by the ratio in the table and round up.

Worked example: a 100-occupant assembly space with a 50/50 split and a ratio of 1 water closet per 25 women needs 50 divided by 25 = 2 water closets. A fraction of a fixture is always a whole fixture.

Water Heaters

Water heaters are pressure vessels and combustion appliances at once, so questions split into temperature-and-pressure (T&P) protection, venting, and installation location.

Every storage water heater needs a listed T&P relief valve, with the temperature element set at or below 210 degrees F and the pressure element at or below the tank's rated working pressure, commonly 150 psi. The discharge pipe must be the full size of the valve outlet, must not be reduced or trapped, must have no valve between heater and relief valve, must run by gravity, and must terminate where discharge is visible, typically not less than 6 in and not more than 24 in above the floor or outside above grade. A capped or plugged T&P is an automatic fail.

Location rules: a pan with a drain where leakage causes damage, two straps in seismic zones (upper third and lower third), and a gas-fired heater in a garage elevated so the ignition source is 18 in above the floor. Closed systems need a thermal expansion tank. Storage above 120 degrees F needs scald protection such as a thermostatic mixing valve, and 140 degrees F storage is used to limit Legionella growth.

Worked example: how long does a 40,000 BTU/hr burner take to raise 40 gallons from 50 to 140 degrees F? Water weighs 8.33 lb/gal, so 40 gal is 333 lb; a 90 degree rise needs 333 x 90 = 30,000 BTU; at 40,000 BTU/hr that is 0.75 hr, or 45 minutes, ignoring standby loss.

Fuel Gas Piping and Venting

Fuel gas work is about three things: sizing the pipe, proving it tight, and getting the products of combustion outside.

Pressure: natural gas is delivered near 7 in. water column (about 0.25 psi) and manifolded near 3.5 in. wc; propane at about 11 in. wc. Because these are inches of water rather than psi, questions often hinge on conversion. One psi equals about 27.7 in. wc.

Sizing uses the longest-length method. Add the nameplate input of every appliance downstream in BTU/hr, divide by the heating value (about 1,000 BTU per cubic foot for natural gas, about 2,500 for propane) to get cubic feet per hour, then read the table using the longest run in feet. Pipe size is set by load and distance together.

Installation essentials: a shutoff valve and sediment trap (drip leg) ahead of each appliance, unions, protection where pipe passes through masonry, proper support and sleeving, and bonding of the gas piping. Appliance connectors are limited in length, typically 6 ft, and cannot be concealed or run through walls.

Venting: gravity vent connectors rise toward the chimney at 1/4 in per foot with a minimum rise off the draft hood, and listed vents terminate at least 2 ft above anything within 10 ft and at least 3 ft above the roof surface.

Worked example: a furnace at 100,000 BTU/hr, a water heater at 40,000, and a range at 35,000 total 175,000 BTU/hr. At 1,000 BTU/ft3 that is 175 cubic feet per hour; enter the table at the longest run and select the smallest pipe that carries it.

Safety, Tools, and Jobsite Practices

Jobsite questions reward the person who thinks about what kills you first: trench collapses, falls, and confined spaces.

Trenches: any excavation 5 ft deep or more needs cave-in protection, meaning sloping, benching, shoring, or a trench box. Soil type sets the slope, and 1-1/2:1 is a common starting point. Provide a ladder within 25 ft of every worker, keep spoil piles and equipment at least 2 ft back from the edge, and locate utilities before the first shovel. Never step into an unprotected 6 ft trench to check it.

Falls and ladders: fall protection is required above 6 ft in construction. Ladders are set at a 4:1 angle (1 ft out for every 4 ft of height), extend 3 ft above the landing, and are tied off. That 4:1 rule appears constantly.

Tools and energy: GFCI protection on temporary power, lockout/tagout before working on a circuit or valve, respect for press tools that pinch, augers that bite, and the need for eye and hearing protection. Hot work such as soldering, brazing, or cutting needs a permit, a fire watch, and a cleared area. Gas cylinders stay upright and capped; solvent cements and primers get ventilation and SDS access. On any repair, protect the potable system with clean tools, washed hands, and a backflow device on temporary connections.

Worked example: a ladder reaches a 20 ft eave and must extend 3 ft above it, so the working length is 23 ft. Set the base 23 divided by 4, about 5.75 ft, from the wall.

Plan Reading, Math, and System Layout

Plan reading is where the other domains get applied. A plumbing set usually includes floor plans showing fixtures and routes, an enlarged plan for tight areas, a single-line riser diagram showing stacks, branches, and vents, detail sheets, and schedules listing fixtures and equipment.

Read the title block, the scale (1/4 in = 1 ft is common for floor plans), the north arrow, and the legend before you measure anything. Symbols are fair game: gate or ball valve, check valve, floor drain (FD), roof drain (RD), water closet (WC), vent through roof (VTR), and cleanout (CO), along with material abbreviations. Never assume a pipe size that is not labeled. Notes such as 'by others' or 'not in contract' are classic traps.

Layout math is mostly right triangles and offsets. A 45 degree offset forms an isosceles right triangle: travel (the diagonal) equals offset times 1.414, and the run equals the offset. A 22-1/2 degree offset uses roughly 2.6 times the offset for travel. Add fitting take-outs to measured center-to-center lengths to get developed length before ordering pipe.

Worked example: a stack must offset 12 in horizontally using 45s. Travel = 12 x 1.414 = 16.97, about 17 in, and the horizontal run is also 12 in, so mark the pipe 17 in between fitting centers. Scale conversion is tested the same way: a 3 in line on a 1/4 in = 1 ft plan represents 12 ft in the field.

Journeyman Plumber cheat sheet

Quick reference

Plumbing Code and Regulations

  • The IPC and the UPC are the two most widely adopted model plumbing codes; the locally adopted edition plus local amendments is what is enforceable, and the authority having jurisdiction (AHJ) interprets it.

  • Horizontal drainage pipe slopes a minimum of 1/4 inch per foot for sizes 2-1/2 inches and smaller, and 1/8 inch per foot for 3-inch through 6-inch pipe.

  • A trap must maintain a liquid seal between 2 and 4 inches deep, measured from the trap weir to the top of the dip.

  • Vent pipe may not be smaller than 1-1/4 inches nominal and must be at least one-half the diameter of the drain it serves.

  • Cleanouts are required at the base of each stack, at the upper end of horizontal drains, at intervals not exceeding 100 feet, and at changes of direction greater than 135 degrees.

  • A vent must not be installed within two pipe diameters of the trap weir (crown venting), and double trapping and S-traps are prohibited.

  • Vent terminals must extend at least 6 inches above the roof surface and be kept at least 10 feet from doors, openable windows, and outdoor air intakes, and 3 feet above any forced-air inlet within 10 feet.

  • Concealed work such as underground drains, rough-in piping, and gas piping must be inspected and approved before it is covered.

Quick reference

Drainage, Waste, and Vent Systems

  • One drainage fixture unit (DFU) represents approximately 1 cubic foot per minute of probable discharge, or about 7.48 gallons per minute.

  • Common fixture unit values: water closet 3 (flush tank) or 4 (flushometer), lavatory 1, bathtub 2, shower 2, kitchen sink 2, dishwasher 2, washing machine 2, floor drain 1.

  • Trap arm developed length from the trap weir to the vent fitting is limited to roughly 5 feet for 1-1/4 inch, 6 feet for 1-1/2 inch, 8 feet for 2 inch, 12 feet for 3 inch, and 16 feet for 4 inch.

  • A vent must rise vertically at least 6 inches above the flood level rim of the fixture before any horizontal offset, except where wet venting or stack venting is specifically permitted.

  • The building drain runs from the inside face of the building wall to a point 30 inches outside the building; beyond that point the same pipe is the building sewer.

  • Use a sanitary tee or combination fitting where flow turns from vertical to horizontal, and a wye or combination where flow turns from horizontal to horizontal.

  • A backwater valve is required where a fixture's flood level rim is below the elevation of the next upstream manhole cover on the sewer.

  • Vent types include individual, common, wet, stack, circuit, and island (loop) vents; an air admittance valve may only be substituted where the adopted code permits it.

Quick reference

Water Supply and Distribution

  • Static pressure in a potable water distribution system is limited to 80 psi; where street or main pressure exceeds that, a pressure-reducing valve must be installed.

  • A minimum residual pressure is needed at fixtures: typically 8 psi for standard fixtures and much higher flowing pressures (roughly 15 to 35 psi) for flushometer valves.

  • Water velocity is normally kept between about 5 and 8 feet per second; higher velocities cause noise, erosion, and excessive pressure loss.

  • Backflow protection options include air gaps, reduced-pressure-zone assemblies, double-check valve assemblies, pressure vacuum breakers, and atmospheric vacuum breakers, chosen by degree of hazard.

  • A closed system protected by a backflow preventer or check valve needs a thermal expansion tank to absorb the volume increase as water is heated.

  • Fixture unit demand is converted to gallons per minute using Hunter's curve; a lavatory is typically 1 fixture unit and about 1 gpm of demand.

  • Water hammer arrestors are installed near quick-closing valves such as flushometers, solenoids, and washing machine valves to absorb the pressure surge.

  • Common distribution materials are copper types K, L, and M, PEX, CPVC, and PEX-AL-PEX; underground service pipe is buried below the local frost depth.

Quick reference

Plumbing Fixtures and Appliances

  • Maximum flow rates: water closet 1.6 gallons per flush (1.28 gpf is common today), urinal 1.0 gpf, showerhead 2.5 gpm at 80 psi, kitchen and lavatory faucets 2.2 gpm, public lavatory faucets about 0.5 gpm.

  • A water closet requires at least 15 inches from its centerline to any side wall or partition and at least 21 inches of clear space in front of the bowl.

  • A water closet compartment is at least 30 inches wide and 60 inches deep; an accessible water closet seat is set 17 to 19 inches above the floor.

  • Accessible counters are a maximum of 34 inches high (36 inches where the approach is not parallel) with knee and toe clearance below.

  • Each fixture must have a trap with a 2 to 4 inch seal, and the fixture outlet must be above the trap weir so the trap cannot be double-trapped.

  • Floor drains in areas subject to sewer gas or evaporation require trap primers to maintain the seal.

  • Indirect waste connections, such as ice machine or food service drains, require an air gap or air break and may not be directly connected to the drainage system.

  • Faucet and fixture outlets must terminate above the flood level rim of the receptor to provide an air gap against backflow.

Quick reference

Water Heaters

  • A temperature and pressure relief valve is typically rated at 150 psi and 210 degrees F and must be installed in the top 6 inches of the storage tank.

  • The relief valve discharge pipe must be full size, flow by gravity, contain no valves or traps, and terminate not more than 6 inches above the floor or outside the building.

  • Recovery in gallons per hour equals input BTU per hour times efficiency, divided by 8.33 times the temperature rise.

  • Storage water heaters are commonly set to 120 degrees F for scald prevention, or 140 degrees F with a tempering (mixing) valve at the point of use.

  • A gas-fired water heater installed in a garage must have its ignition source elevated at least 18 inches above the floor.

  • A drain pan at least 1-1/2 inches deep with a piped drain is required where a leak would cause damage to the structure or finished space.

  • Seismic strapping uses two straps, one in the upper third and one in the lower third of the tank, fastened to the structure.

Quick reference

Fuel Gas Piping and Venting

  • Typical manifold pressures are about 3.5 inches water column for natural gas and 10 to 11 inches water column for propane; appliance inlet pressure may not exceed 14 inches water column (1/2 psi).

  • A sediment trap (drip leg) is installed downstream of the appliance shutoff valve, as close as practicable to the appliance inlet.

  • The manual shutoff valve must be in the same room as the appliance and within 6 feet of it.

  • Gas pipe is sized by the longest-length method, using total BTU load and equivalent length of fittings to select pipe diameter from code tables.

  • A vent connector needs at least a 12-inch vertical rise before the first elbow, slopes upward at 1/4 inch per foot toward the chimney, and its lateral run is limited relative to the vertical rise.

  • Clearance to combustibles is typically 6 inches for single-wall vent connectors and 1 inch for listed Type B double-wall vent.

  • An unconfined space needs about 50 cubic feet of volume per 1,000 BTU per hour of total input, or free grille area of 1 square inch per 1,000 BTU per hour split evenly between high and low openings.

  • Corrugated stainless steel tubing (CSST) is bonded to the grounding electrode system with a minimum 6 AWG copper conductor.

  • Gas piping is pressure-tested with air or inert gas before being placed in service, and leaks are located with soap solution or an electronic detector, never with a flame.

Quick reference

Safety, Tools, and Jobsite Practices

  • OSHA requires a protective system (sloping, benching, shoring, or a trench box) for any excavation 5 feet deep or greater unless it is solid rock.

  • In trenches 4 feet or deeper, a ladder or other means of exit must be within 25 feet of lateral travel for workers.

  • Spoil and materials are kept back at least 2 feet from the edge of an excavation to prevent cave-in.

  • Portable ladders follow the 4-to-1 rule (base 1 foot out for every 4 feet of height) and extend 3 feet above the landing surface.

  • Call 811 before digging so underground utilities can be located and marked, generally at least two to three working days in advance.

  • Required PPE includes eye protection, gloves, hard hat, and hearing or respiratory protection matched to the task; hot work requires a fire extinguisher and a fire watch after the work is complete.

  • Pipe wrenches are pulled, not pushed, and two wrenches are used (one to hold, one to turn) so joints elsewhere in the assembly are not loosened.

  • Lockout/tagout procedures are followed before servicing electrical equipment, and permit-required confined spaces require atmospheric testing and an attendant.

Quick reference

Plan Reading, Math, and System Layout

  • At a scale of 1/4 inch = 1 foot, one inch on the drawing equals 4 feet in the field; convert by multiplying the measured drawing distance by 4.

  • Total fall equals slope multiplied by run: a 1/4 inch per foot slope over 20 feet produces 5 inches of fall.

  • For a 45-degree offset, travel equals offset times 1.414 and offset equals travel times 0.707; for 22-1/2 degrees the travel factor is 2.613, and for 60 degrees it is 1.155.

  • One psi equals 2.31 feet of water column, and each foot of elevation adds 0.433 psi of static pressure.

  • Heat load in BTU per hour equals gallons per minute times 500 times the temperature difference.

  • One gallon occupies 231 cubic inches; pipe volume per foot in gallons equals pi times the inside radius squared times 12, divided by 231.

  • One drainage fixture unit is roughly 7.5 gallons per minute, and one cubic foot equals 7.48 gallons.

  • Invert elevation equals rim or grade elevation minus the depth of cover, and the invert of a downstream pipe is set by subtracting the fall from the upstream invert.

Journeyman Plumber key terms

Trap seal

The depth of water held in the bend of a plumbing trap, typically 2 to 4 inches, that blocks sewer gases from entering the building. Evaporation, siphonage, or backpressure can destroy the seal and defeat the trap.

Related: Trap arm, Air admittance valve
Trap arm

The section of pipe between a fixture trap's weir and the point where it ties into a vented drain. Its length and fall are limited by code so the trap seal is not siphoned out.

Related: Trap seal, Horizontal branch
Vent stack

A vertical pipe that supplies air to the drainage system and carries sewer gases to outdoor air. It typically serves fixtures on more than one floor and extends through the roof.

Related: Stack vent, Air admittance valve
Stack vent

The extension of a soil or waste stack above the highest fixture connection that runs to open air. It vents the stack itself and is sometimes called a vent extension.

Related: Vent stack, Soil stack
Air admittance valve

A one-way mechanical valve that admits air into a drain to protect trap seals but does not release sewer gas. Code limits where it may be used, and it usually needs accessible installation.

Related: Vent stack, Trap seal
Drainage fixture unit

A number expressing the probable drainage load of a fixture relative to a standard fixture. Fixture units are used to size building drains, stacks, and vents.

Related: Building drain, Soil stack
Building drain

The lowest pipe of a building's drainage system, receiving soil and waste from stacks and branches and carrying it to the building sewer. It ends at or near the building wall.

Related: Building sewer, Cleanout
Building sewer

The pipe that carries sewage from the end of the building drain to the public sewer or a private disposal system. It begins outside the building foundation.

Related: Building drain, Backwater valve
Soil stack

A vertical drainage pipe that carries the discharge of water closets, with or without other fixtures, down to the building drain.

Related: Stack vent, Drainage fixture unit
Horizontal branch

A drain pipe that connects fixture drains to a stack or building drain and runs at a slope, no more than 45 degrees from horizontal.

Related: Trap arm, Cleanout
Cleanout

An accessible fitting with a removable plug that allows a drain line to be rodded or snaked. Code requires them at stack bases, on long horizontal runs, and at certain changes of direction.

Related: Building drain, Horizontal branch
Backwater valve

A one-way check device installed in a drain to prevent sewage from backing up into the building when the public sewer surcharges.

Related: Building sewer, Cleanout
Developed length

The total length of pipe measured along its centerline, following every fitting and change of direction, rather than the straight-line distance. It is used to size vents and check trap arm limits.

Related: Vent stack, Offset
Rough-in

The construction stage when pipe, fittings, and supports are installed before fixtures are set and walls are closed. Rough-in work must be inspected before it is concealed.

Related: Floor drain, Flushometer valve
Floor drain

A fixture with a strainer and a trapped body set into the floor to receive surface water and spills. It is usually protected by a trap primer or a deep-seal trap.

Related: Trap seal, Rough-in
Flushometer valve

A flush valve that uses line pressure to deliver a measured flush to a water closet or urinal. It requires adequate pipe size and pressure at the fixture to work properly.

Related: Pressure-reducing valve, Rough-in
Air gap

The unobstructed vertical distance between a water supply outlet and the flood-level rim of the fixture or receptacle it serves. It is the most reliable form of backflow protection.

Related: Backflow preventer, Cross-connection
Backflow preventer

A device or assembly that stops contaminated water from reversing into the potable supply because of backpressure or backsiphonage.

Related: Air gap, Cross-connection
Cross-connection

Any actual or potential link between the potable water system and a source of contamination. It must be eliminated or protected against with an approved device or air gap.

Related: Air gap, Potable water
Water hammer arrestor

A chamber containing a trapped air cushion or a moving piston that absorbs the pressure surge created when a valve closes quickly, reducing noise and pipe damage.

Related: Pressure-reducing valve, Thermal expansion
Pressure-reducing valve

A device that lowers incoming water pressure to a safe, usable level, protecting fixtures, appliances, and piping from excessive pressure.

Related: Water hammer arrestor, Flushometer valve
Thermal expansion

The increase in water volume as it is heated. In a closed system this raises pressure and must be relieved by a device such as an expansion tank or a thermal expansion valve.

Related: Temperature and pressure relief valve, Recirculation loop
Temperature and pressure relief valve

A safety valve on a water heater that opens when internal temperature or pressure exceeds its rating, discharging hot water to a safe approved location.

Related: Thermal expansion, Anode rod
Anode rod

A sacrificial metal rod inside a tank-type water heater that corrodes in place of the steel tank, extending the tank's service life.

Related: Temperature and pressure relief valve
Recirculation loop

A piping arrangement that keeps hot water circulating from the heater toward fixtures so hot water arrives quickly, reducing wait time and wasted water.

Related: Thermal expansion
Draft hood

A fitting on a gas appliance that admits dilution air and stabilizes the draft into the vent, helping prevent flue gases from spilling into the room.

Related: Sediment trap, Confined space
Sediment trap

A short downward leg of pipe installed near a gas appliance's inlet that collects dirt, scale, and moisture before they can reach the appliance controls.

Related: Gas manifold, Draft hood
Corrugated stainless steel tubing

A flexible gas piping material sold in coils and joined with special fittings. It must be installed per its listing and bonded to the electrical grounding system.

Related: Gas manifold, Sediment trap
Gas manifold

A header or fitting that splits a single gas supply line into multiple branch lines, each serving an individual appliance or outlet.

Related: Corrugated stainless steel tubing, Sediment trap
Lockout/tagout

A safety procedure that isolates energy sources and applies locks and tags so equipment cannot be energized or started while work is being performed on it.

Related: Confined space, Trench shoring
Confined space

An area with limited entry and exit that is not designed for continuous occupancy and may contain hazardous air or engulfment hazards. Entry requires testing, permits, and procedures.

Related: Lockout/tagout, Draft hood
Trench shoring

Temporary support for an excavation, such as sloping, shielding, or bracing, used to protect workers from cave-ins and falling material.

Related: Lockout/tagout, Confined space
Isometric drawing

A pictorial drawing that shows piping in three dimensions along angled axes, used to plan, coordinate, and communicate a system layout.

Related: Offset, Developed length
Offset

A pair of fittings joined by a pipe that shifts a run sideways or vertically, used to pass around obstructions or line up with a fixture or stack.

Related: Isometric drawing, Developed length
Grade

The slope of a drain pipe, expressed as a percentage or as inches of fall per foot of run. It must be enough to carry solids without leaving liquids behind.

Related: Building drain, Developed length
Authority having jurisdiction

The official or agency that enforces the plumbing code in a local area, interprets its requirements, issues permits, and inspects completed work.

Related: Permit
Permit

Written authorization from the authority having jurisdiction to install or alter plumbing work. It must be obtained before work starts and is closed out after inspection.

Related: Authority having jurisdiction
Potable water

Water that is safe for drinking and free of harmful contamination, as supplied to fixtures and appliances throughout the plumbing system.

Related: Cross-connection, Air gap

Journeyman Plumber study plan

8 weeks · About 7 hours per week

Week 1

Drainage, Waste, and Vent Systems

  • Diagram a full DWV system from a stack out through the building drain, labeling every trap, vent, and fitting by name

  • Calculate proper fixture-unit loads for a branch, a stack, and a building drain using a fixture-unit table you build yourself

  • Explain the difference between a vent stack, stack vent, and relief vent aloud without notes

  • Identify slope requirements for drain pipe sizes from 1-1/4 in through 6 in and state where each applies

Your checkpoint

A hand-drawn DWV riser diagram with fixture-unit totals written at every branch, stack, and building drain

Week 2

Drainage, Waste, and Vent Systems & Plumbing Code and Regulations

  • Solve 20 trap-arm distance and developed-length problems for common fixtures

  • Distinguish wet venting, common venting, and circuit venting by sketching each arrangement

  • Locate and paraphrase the code sections governing vent termination distances from windows, doors, and air intakes

  • Write out the rules for cleanout placement, sizing, and access in your own words

Your checkpoint

A 25-question self-written DWV quiz with answer key and code citations, scored at 90% or better

Week 3

Water Supply and Distribution & Plumbing Code and Regulations

  • Size water supply piping for a two-bath house using both the fixture-unit method and the velocity method, then compare results

  • Compute pressure loss across a run using friction-loss tables and static head for a two-story installation

  • Explain backflow prevention device selection for three different scenarios

  • Summarize the code requirements for water distribution testing, disinfection, and minimum pipe burial depth

Your checkpoint

A one-page water supply sizing worksheet for a sample two-bath house showing pipe sizes, pressure loss, and remaining pressure at the farthest fixture

Week 4

Plan Reading, Math, and System Layout & Drainage, Waste, and Vent Systems

  • Convert between plan scale, actual dimensions, and pipe lengths on at least 10 practice measurements

  • Calculate grade, fall, and invert elevations for a building sewer given two known elevations

  • Compute volume, capacity, and material takeoff quantities for a drainage layout from a dimensioned sketch

  • Re-solve 15 missed DWV questions from Week 1-2 and explain each error in writing

Your checkpoint

A takeoff sheet for a sample drainage layout listing pipe lengths, fitting counts, and invert elevations with all math shown

Week 5

Plumbing Fixtures and Appliances & Fuel Gas Piping and Venting

  • List installation and rough-in dimensions for water closets, lavatories, and tub/shower units

  • Match each fixture type to its trap size, supply connection size, and minimum fixture-unit value

  • Trace a fuel gas line from meter to appliance, sizing each segment by load and length

  • State combustion air, clearances, and venting requirements for a Category I appliance from memory

Your checkpoint

A comparison chart of 12 fixtures and appliances giving trap size, supply size, fixture units, and gas input/connection size

Week 6

Water Heaters & Plumbing Fixtures and Appliances

  • Size a water heater for a 3-bedroom, 2-bath home using first-hour rating and peak-hour demand

  • Identify the components and failure points of a temperature and pressure relief valve and its discharge piping requirements

  • Compare tank, tankless, and heat-pump water heaters on recovery, venting, and installation constraints

  • Describe thermal expansion control and backflow protection for a closed water heater system

Your checkpoint

A written water heater selection memo recommending one unit for a given household, with sizing math, venting plan, and T&P discharge details

Week 7

Safety, Tools, and Jobsite Practices & Plumbing Code and Regulations

  • Build a job-site hazard checklist covering trenching, confined space, and soldering fire watch

  • Name the correct tool for 15 common plumbing tasks and state one safety rule for each

  • Summarize licensing, permit, inspection, and testing obligations under the code for a typical residential job

  • Practice 30 rapid-fire code questions on definitions, administration, and general regulations

Your checkpoint

A permit-and-inspection checklist plus a jobsite hazard checklist you could take to a real job tomorrow

Week 8

Drainage, Waste, and Vent Systems & Water Supply and Distribution & Plumbing Code and Regulations & Plumbing Fixtures and Appliances & Water Heaters & Fuel Gas Piping and Venting & Safety, Tools, and Jobsite Practices & Plan Reading, Math, and System Layout

  • Complete two full-length timed practice exams under test conditions

  • Rank every missed question by domain and re-study the two weakest domains

  • Recite the 20 formulas and code numbers you most often forget, from a self-made flashcard set

  • Review your Week 1-7 deliverables and rework any goal you could not complete cleanly

Your checkpoint

A scored 100-question practice exam with every wrong answer corrected and cited, plus a one-page final review sheet

Milestones

Week 2: Score at least 80% on the self-written DWV quiz and correctly sketch three venting arrangements without notes

Week 4: Complete the drainage takeoff with no arithmetic errors and score at least 85% on a mixed DWV-and-math practice set

Week 6: Produce a code-correct water heater selection memo and pass a 40-question mixed fixtures/gas/water-heater quiz at 80% or better

Week 8: Score at least 80% on both timed full-length practice exams, with no domain below 70%

Journeyman Plumber exam day

Your checklist

Government-issued photo ID

Bring the original document - photocopies and expired IDs are almost never accepted. Confirm with the provider which forms of ID are approved (driver's license, state ID, passport, military ID) and whether the name must match your registration exactly.

Admission letter or scheduling confirmation

Print a copy and also save it offline on your phone in case you need it before entering the testing area. It usually shows your candidate number, test site address, and reporting time.

Two or three writing instruments

Bring spare pencils or pens in case one fails. If your exam is computer-delivered, confirm with the provider whether scratch paper and a pencil are supplied at the workstation or whether you may bring your own.

Non-programmable calculator (only if permitted)

Many plumbing licensing exams restrict or prohibit calculators, and some computer-delivered exams include an on-screen calculator. Confirm with the provider before relying on one, and never bring a programmable or phone-based calculator.

Approved code book, if your exam is open-book

Confirm with the provider whether your exam is open-book, which code edition and year are allowed, and whether tabs, highlights, or handwritten notes are permitted. If the exam is closed-book, leave the book at home - outside materials are a common disqualifier.

Directions, parking plan, and arrival time

Look up the test site the day before, identify parking or transit, and confirm the required check-in time with the provider. Aim to arrive well before check-in so a delay does not cost you your seat.

A clear picture of the test format

Know the number of questions, the time limit, whether questions are multiple choice or mixed format, and whether the exam is paper or computer delivered. Confirm these details with the provider rather than relying on secondhand information.

Comfort layers and water

Test centers are often cold, and a long exam is easier to sit through when you are comfortable. Confirm whether a water bottle or snacks are allowed at the workstation or only during scheduled breaks.

Leave prohibited items behind

Cell phones, smartwatches, fitness trackers, notes, and study materials are typically banned from the testing room. Plan where they will go and confirm the provider's storage or locker policy in advance.

Advance approval for any accommodation

If you need extra time, a separate room, or another accommodation, request it from the provider well before the test date - approval is rarely granted on exam day.

Your scoring and retake information

Know the passing score, whether results are immediate or mailed, and how a retake works if you do not pass. Confirm the specifics with the provider, since these vary by jurisdiction.

Plan the day

Final 72 hours

Confirm your appointment, test site address, reporting time, and what you are allowed to bring. Re-read the provider's candidate bulletin for ID, code-book, and calculator rules. Stop learning new material; instead, review your own notes on the topics that cost you the most practice-question points - fixture units, slope and drainage, venting, water supply sizing, and code definitions.

Final 72 hours

Do one or two timed practice sets under exam-like conditions, then review the misses by category rather than re-drilling the same questions. Confirm transportation and a backup plan, and protect your sleep schedule so you are not reading code tables at midnight.

Final 24 hours

Pack your bag: ID, admission letter, writing instruments, approved reference materials, directions, and water. Lay out clothes and set two alarms. Do a light review of formulas and frequently confused code terms, but no heavy cramming - a tired brain loses more points than one extra chapter gains.

Morning of

Eat a normal meal, hydrate moderately, and leave with buffer time. Avoid heavy caffeine if you are not used to it. Arrive early, keep your phone stowed before you enter the check-in area, and use any waiting time for calm breathing rather than last-minute questions.

During the test

Read the full question and every answer choice before selecting - distractor answers in plumbing exams often are plausible code values from a different table. Answer the easy questions first if you can flag and return; never leave a blank if there is no penalty for guessing. Watch the clock at the halfway point and adjust pace. For code questions, think about which chapter or table the question is pointing to before choosing.

During the test

Use breaks only as the provider allows, and note your remaining time before you leave the room. If a question seems to depend on a local amendment you do not know, eliminate what is clearly wrong and choose the answer most consistent with the model code, then move on.

Rules to check

  • Bring identification that matches your registration name exactly; a mismatch or an expired document can result in being turned away, so confirm the provider's ID policy in advance.

  • Do not bring phones, smartwatches, notes, or other unauthorized material into the testing room. Possession of a device during the exam is commonly treated as misconduct regardless of intent.

  • Confirm the provider's rules on reference materials before exam day. Open-book and closed-book exams have very different consequences for bringing a code book, and annotated or tabbed books may be restricted.

  • Breaks are typically limited and may be timed or unsupervised only in specified areas. Ask at check-in what the break policy is and whether your clock keeps running.

  • Scoring, passing thresholds, and retake waiting periods are set by your licensing authority and vary widely. Do not assume a score you heard from another candidate applies to you - confirm with the provider.

  • Follow all proctor instructions and complete any security or identity verification steps. Arguing with or ignoring proctor direction can end your session.

  • If you believe a question is defective, note it if the provider allows comments and otherwise keep going; do not spend several minutes on one item at the expense of the rest of the exam.

  • Results reporting and appeal procedures are jurisdiction-specific - confirm with the provider how and when results are released and what the process is if you believe an error occurred.

Journeyman Plumber FAQ

How many Journeyman Plumber practice questions are available?

The practice set has 199 Journeyman Plumber questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many Journeyman Plumber flashcards are available?

The flashcard set has 32 Journeyman Plumber cards. Each card shows the term and its definition.

Which topics does the Journeyman Plumber study material cover?

The Journeyman Plumber study material has 8 sections, including Plumbing Code and Regulations, Drainage, Waste, and Vent Systems, and Water Supply and Distribution.

What format facts does the catalog list for the Journeyman Plumber exam?

The catalog lists these item types: multiple choice for the Journeyman Plumber exam.