FAA A&P Mechanic Practice Test

FAA Aviation Mechanic (A&P) Certification - Knowledge Tests

FAA A&P Mechanic overview

  • 200 practice questions
  • 32 flashcards
  • 3 study guide topics
  • 38 key terms

What you'll study

  • General33%
  • Airframe33%
  • Powerplant34%

The FAA Aviation Mechanic certificate - widely called the A&P - is the U.S. credential that lets a mechanic approve an aircraft for return to service after maintenance, preventive maintenance, or alteration. The letters stand for the two ratings a mechanic may hold: Airframe and Powerplant. The certificate is issued by the Federal Aviation Administration through its Airmen Certification system, and the mechanics, repairmen, and designee programs are administered under the agency's Pilots & Airmen section. The credential is intended for people working in or entering aircraft maintenance: repair station technicians, airline and general aviation maintenance personnel, and military-trained mechanics transitioning into civil aviation. Knowledge testing is organized around three subject areas - General, Airframe, and Powerplant. General covers regulations, mathematics, physics, materials, and hand skills; Airframe covers structures, systems, and assembly; Powerplant covers engines, propellers, and related systems. Each rating carries its own knowledge test and a subsequent oral and practical evaluation. To prepare, work through the FAA handbooks and manuals published under Regulations > Handbooks & Manuals, review current regulations and advisory circulars, and drill question sets organized by subject area rather than randomly. Administrative details - test centers, scheduling, fees, eligibility, and retake rules - change over time, so confirm them directly with the FAA; the agency's site is the authoritative source, and this page does not claim any official affiliation with it.

Common mistakes

Reads the stem, recognises a familiar true statement in the options, and selects it without registering a qualifier such as EXCEPT, NOT, FIRST, or LEAST likely.

Many written items test the negative case, and once a true statement appears the brain pattern-matches to it and stops reading the stem's qualifier.

What to do instead

Underline or silently repeat the qualifier before looking at any option. After choosing, substitute the answer back into the stem as a full sentence ('The item that is NOT required is...') and confirm it makes sense before moving on.

Solves weight-and-balance items by averaging the arms of the loaded items instead of multiplying each weight by its arm and summing moments.

CG problems superficially resemble averaging problems, and under time pressure the moment column feels like extra work, so it gets dropped.

What to do instead

Always lay out three columns: weight, arm, and moment (weight x arm). Sum weight and sum moment separately, then CG = total moment / total weight. Sanity-check that the result falls between the smallest and largest arm in the table.

Applies the 100-hour inspection rule to an aircraft described as privately operated, or applies the annual rule to an aircraft carrying persons for hire, without checking which trigger condition the stem actually describes.

Both intervals involve the same paperwork and both are described with similar wording, so the number is recalled but the condition that activates it is not.

What to do instead

Memorise inspection requirements as a table of triggers rather than isolated numbers: annual applies to all aircraft; 100-hour is tied to specific operations such as carrying persons for hire or giving flight instruction for hire; progressive programs are an approved alternative. Match the stem to the trigger first, then the interval.

Substitutes milliamps, kilo-ohms, or microfarads straight into Ohm's law and power formulas without converting to base units, producing an answer off by a factor of 1,000 or more.

Distractor options are usually scaled the same way as the givens, so the wrong arithmetic still looks like a plausible choice; prefixes get read as decoration rather than as multipliers.

What to do instead

Write every quantity in base units (A, V, ohms, W) before substituting, then convert the result back into the units the options use. Keep a prefix reference in memory: micro = 10^-6, milli = 10^-3, kilo = 10^3, mega = 10^6.

Selects 7075-T6 when the item asks which aluminium alloy has the best corrosion resistance, or picks 2024 for a part that must be formed easily, basing the choice on strength alone.

7075 is remembered as 'the strong one' and 2024 as 'aircraft aluminium', so the property actually being asked about gets silently replaced by a strength ranking.

What to do instead

Learn the alloys as trade-offs, not superlatives: 2024 has high strength but poor corrosion resistance and is normally used clad; 7075 has the highest strength and the poorest corrosion resistance and is not weldable; 6061 has good corrosion resistance and is easily formed and welded. Answer the property named in the stem.

Mislabels intergranular corrosion as exfoliation (or the reverse) and then selects the wrong inspection or removal action for the location described in the stem.

Both attack the grain boundaries of aluminium and both are described with words like lifting, flaking, and powdery, so the distinguishing visual and location cues get glossed over.

What to do instead

Anchor each type to a picture and a place: intergranular attacks along grain boundaries in thick sections and often looks like grey powder or a sugary surface; exfoliation is the severe layered form where material lifts and flakes away from the surface; galvanic occurs where dissimilar metals touch. Identify the type from the description first, then match the treatment to the depth of attack.

Treats a system relief valve and a pressure regulator as interchangeable components, or assumes the pump itself sets system pressure.

Both are valves that control pressure, and both appear in the same chapter of any study guide, so the functional difference is blurred.

What to do instead

Ask what the component must do. Preventing damage at an overpressure limit is a relief valve; holding a regulated operating pressure during normal flow is a regulator or unloading valve. Remember that a constant-displacement pump delivers volume, and pressure is created by the restriction downstream of it.

States that leaning the mixture always raises exhaust gas temperature, or treats peak EGT as the correct setting at every power level.

The phrase 'lean to peak EGT' is memorised as a rule without the shape of the curve that produces it, so the rich side and the lean side of peak are treated as the same.

What to do instead

Sketch the EGT versus fuel flow curve every time: leaning from full rich raises EGT, peak is a single point, and leaning further past peak lowers EGT. Then apply the accepted targets: approximately 100 degrees F rich of peak for best power, and at or lean of peak for best economy only within the engine manufacturer's limits.

Judges a magneto check only by whether the RPM drop falls inside a memorised range, without recording which magneto was selected, the drop on each, and the difference between them.

The published limits are remembered as one number, so the diagnostic content of the check, the drop pattern, is discarded.

What to do instead

For every magneto check note three things: which magneto is selected, the RPM drop on that magneto, and the differential between the two. Use the airframe or engine manufacturer's limits for both figures, then read the pattern: an excessive drop points to an ignition fault on the selected magneto, while no drop or rough running when selecting one magneto points to a grounding or switch problem.

Uses N1 and N2 interchangeably, or treats EGT on a turbine engine as a control input the way mixture is on a reciprocating engine.

Both tachometers read in percent RPM and sit side by side on the same panel, and the pilot's power lever feels analogous to a throttle, so the roles of the two spools and of EGT get conflated.

What to do instead

For each engine type, state which spool sets power and which is the limiting indicator: on most turbofans N1 is the power reference and N2 is the high-pressure spool; on turboprops the gas generator speed (Ng) is usually the reference. EGT is monitored against limits, never leaned to a target. Apply the same parameter logic to start malfunctions: a hung start is RPM stalling below idle, a hot start is EGT exceeding its limit.

Exam requirements can change. Confirm current details with the exam provider.

FAA A&P Mechanic practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1General

    What is the area of a circle that has a radius of 5 inches?

    1. 15.71 square inches
    2. 31.42 square inches
    3. 78.54 square inches Correct answer.
    4. 157.1 square inches

    Explanation

    Area of a circle equals pi times the radius squared, so 3.1416 x 5 x 5 = 78.54 square inches. The radius, not the diameter, is used in the formula.

  2. Question 2General

    Which of these quantities is a scalar?

    1. Mass Correct answer.
    2. Weight
    3. Acceleration
    4. Velocity

    Explanation

    A scalar is fully described by magnitude alone, and mass meets that definition. Velocity, weight, and acceleration all require a direction as well as a magnitude.

  3. Question 3General

    Which statement correctly describes current in a series circuit?

    1. It is zero in every component except the one with the lowest resistance.
    2. It is the same through every component. Correct answer.
    3. It divides among the components in proportion to their resistance.
    4. It is greatest in the component with the highest resistance.

    Explanation

    A series circuit provides only one path for electron flow, so the same current passes through each component. Voltage, not current, divides across series resistances.

  4. Question 4General

    A Class C fire involves which of the following?

    1. Combustible metals
    2. Flammable liquids
    3. Ordinary combustible materials
    4. Energized electrical equipment Correct answer.

    Explanation

    Fires involving energized electrical equipment are Class C, and the extinguishing agent must be nonconductive. Once power is removed, the fire is classified by the material that is burning.

  5. Question 5General

    In the aluminum alloy designation 2024, the major alloying element is

    1. Magnesium
    2. Silicon
    3. Copper Correct answer.
    4. Zinc

    Explanation

    The first digit of the four-digit wrought aluminum designation identifies the principal alloying element, and the 2xxx series is alloyed mainly with copper. Copper-bearing alloys are strong but require protection against corrosion.

  6. Question 6General

    In weight and balance work, the arm of an item is defined as

    1. The distance from the datum to the center of gravity of the item Correct answer.
    2. The distance between the forward and aft center of gravity limits
    3. The point at which the aircraft would balance if suspended
    4. The weight of the item multiplied by its distance from the datum

    Explanation

    An arm is a measured distance from the datum to the item's center of gravity, usually expressed in inches. Multiplying an arm by a weight produces a moment.

  7. Question 7General

    Compliance with an Airworthiness Directive is

    1. Mandatory, and the compliance must be recorded Correct answer.
    2. Advisory only when the aircraft is operated under Part 91
    3. Recommended but not required for private aircraft
    4. Optional for aircraft that are not flown for hire

    Explanation

    Airworthiness Directives are rules issued to correct unsafe conditions, and the affected aircraft cannot be legally flown until they are complied with. The action taken must be documented in the aircraft records.

  8. Question 8General

    The flare angle used on an AN flare-type fitting is

    1. 60 degrees
    2. 30 degrees
    3. 37 degrees Correct answer.
    4. 45 degrees

    Explanation

    AN flare fittings use a 37-degree flare, which mates with the corresponding cone on the fitting body. Using the wrong flare angle prevents proper sealing and can cause a leak or failure.

  9. Question 9General

    An aircraft burns 12 gallons of fuel per hour. How many gallons are needed for a flight of 3 hours 20 minutes with a 45-minute reserve?

    1. 44 gallons
    2. 49 gallons Correct answer.
    3. 52 gallons
    4. 58 gallons

    Explanation

    Total time is 3.333 hours plus 0.75 hour of reserve, or about 4.08 hours. Multiplying by 12 gallons per hour gives approximately 49 gallons.

  10. Question 10General

    A 24-volt circuit has a total resistance of 6 ohms. What current flows in the circuit?

    1. 4 amperes Correct answer.
    2. 0.25 ampere
    3. 18 amperes
    4. 144 amperes

    Explanation

    Ohm's law states that current equals voltage divided by resistance, so 24 divided by 6 equals 4 amperes. Voltage and resistance must be expressed in volts and ohms.

  11. Question 11General

    Two 12-volt, 25-ampere-hour batteries are connected in parallel. The resulting combination provides

    1. 12 volts and 50 ampere-hours Correct answer.
    2. 24 volts and 50 ampere-hours
    3. 12 volts and 25 ampere-hours
    4. 24 volts and 25 ampere-hours

    Explanation

    In a parallel connection the positive terminals are joined together and the negative terminals are joined together, so the voltage stays the same while the capacity adds. Two 25-ampere-hour batteries therefore give 50 ampere-hours at 12 volts.

  12. Question 12General

    A drawing is marked SCALE 1/2. A line on the drawing measures 4.0 inches. What is the actual length of the part?

    1. 1.0 inch
    2. 0.5 inch
    3. 2.0 inches
    4. 8.0 inches Correct answer.

    Explanation

    A scale of 1/2 means the drawing is half the size of the actual part, so each drawn inch represents two actual inches. Multiplying 4.0 inches by 2 gives 8.0 inches.

  13. Question 13General

    In the designation 2024-T3, the T3 indicates that the alloy has been

    1. Annealed to its softest condition
    2. Cold-worked only, without any heat treatment
    3. Solution heat-treated and then cold-worked Correct answer.
    4. Hot-rolled and stress-relieved

    Explanation

    The T temper designations indicate thermal treatment, and T3 specifically means solution heat-treated, cold-worked to improve strength, and naturally aged. Material in this temper is stronger than the annealed O condition.

  14. Question 14General

    Which situation is most likely to promote galvanic corrosion?

    1. An aluminum sheet washed regularly with clean water
    2. Two identical aluminum alloy plates riveted together in a dry hangar
    3. A painted steel panel exposed to dry desert air
    4. A magnesium casting bolted to a steel bracket in a damp area Correct answer.

    Explanation

    Galvanic corrosion requires two dissimilar metals in contact plus an electrolyte, and dampness provides that electrolyte. Metals far apart on the galvanic scale, such as magnesium and steel, corrode most rapidly.

  15. Question 15General

    FAA Form 337 is used to

    1. Record a major repair or major alteration Correct answer.
    2. Apply for a special flight permit
    3. Report an aircraft accident to the NTSB
    4. Record the annual inspection of an aircraft

    Explanation

    Form 337 documents major repairs and major alterations along with the approved data used and the approving authority. It becomes part of the aircraft's permanent records.

  16. Question 16General

    Under FAA rules, a private pilot may perform preventive maintenance on an aircraft that the pilot

    1. Only at a certificated repair station using approved data
    2. Only if the aircraft is operated for compensation or hire
    3. Owns and operates, provided it is not operated for hire Correct answer.
    4. Only under the direct supervision of a certificated A&P mechanic

    Explanation

    A pilot certificated to at least the private level may perform preventive maintenance on an aircraft the pilot owns and operates, as long as it is not operated for compensation or hire. The work must be recorded in the maintenance records.

  17. Question 17General

    Before opening the filler cap on an aircraft during refueling, the recommended practice is to

    1. Ground the fuel truck to the ramp only
    2. Close all of the aircraft circuit breakers
    3. Remove the static wicks from the wing tips
    4. Bond the aircraft to the fuel source Correct answer.

    Explanation

    Bonding the aircraft to the fuel truck equalizes static potential between the two before fuel transfer begins. A difference in potential can produce a spark and ignite fuel vapor.

  18. Question 18General

    An aircraft has an empty weight of 1,200 pounds with a center of gravity at arm 40. A 200-pound item is added at arm 30. What is the new center of gravity location?

    1. 40.0 inches
    2. 37.5 inches
    3. 39.2 inches
    4. 38.6 inches Correct answer.

    Explanation

    Total moment is (1,200 x 40) plus (200 x 30), or 48,000 plus 6,000, giving 54,000 pound-inches. Dividing by the new total weight of 1,400 pounds gives about 38.6 inches.

  19. Question 19General

    Stress in a structural member is defined as

    1. The deformation produced by an applied load
    2. The internal force per unit of cross-sectional area Correct answer.
    3. The total load carried by the member
    4. The tendency of a load to twist the member

    Explanation

    Stress is the internal resistance expressed as force divided by the area over which it acts, commonly in pounds per square inch. It is distinct from strain, which is the resulting deformation.

  20. Question 20General

    Which procedure is acceptable for removing light surface corrosion from an aluminum alloy part?

    1. Scrub the area with steel wool until bare metal is exposed
    2. Apply household bleach to dissolve the corrosion products
    3. Sand the area with coarse grit paper until the pits disappear
    4. Rub the area with aluminum wool and apply a protective coating Correct answer.

    Explanation

    Aluminum wool or a nonmetallic abrasive removes corrosion without embedding foreign metal particles in the surface. The cleaned area must then be protected with an appropriate coating to prevent recurrence.

  21. Question 21General

    An aircraft has an empty weight of 1,500 pounds with a center of gravity at arm 38. Cargo will be loaded at arm 60, and the aft center of gravity limit is arm 40. What is the maximum cargo weight that can be carried?

    1. 125 pounds
    2. 150 pounds Correct answer.
    3. 175 pounds
    4. 100 pounds

    Explanation

    At the limit, the total moment divided by total weight equals 40: (57,000 + 60W) divided by (1,500 + W) = 40. Solving gives 20W = 3,000, so W equals 150 pounds.

  22. Question 22General

    Layers of metal lifting and flaking in sheets roughly parallel to the surface, often seen on extruded aluminum parts, indicate

    1. Pitting corrosion
    2. Exfoliation corrosion Correct answer.
    3. Galvanic corrosion
    4. Stress-corrosion cracking

    Explanation

    Exfoliation is intergranular corrosion that follows the grain boundaries of heavily worked metal, forcing thin layers apart. Extruded and rolled sections with directional grain structure are especially susceptible.

  23. Question 23General

    A dimension on an aircraft drawing is given as 3.250 plus or minus 0.010. Which measurement of the part is acceptable?

    1. 3.255 inches Correct answer.
    2. 3.262 inches
    3. 3.272 inches
    4. 3.238 inches

    Explanation

    The tolerance permits any dimension from 3.240 to 3.260 inches inclusive. Only 3.255 falls inside that range.

  24. Question 24General

    Under Part 91, maintenance records for work performed on an aircraft must be retained

    1. Until the aircraft is sold to another owner
    2. For 6 months after the work is performed
    3. For 2 years after the work is performed
    4. For 1 year after the work is performed or until the work is superseded Correct answer.

    Explanation

    The regulation requires retention of maintenance, preventive maintenance, and alteration records for at least one year after the work is done, or until the work is repeated or superseded. Records for certain items, such as life-limited parts, must be kept longer.

  25. Question 25General

    Aircraft alternating current systems commonly operate at 400 Hz rather than 60 Hz because the higher frequency

    1. Permits smaller and lighter transformers, motors, and generators Correct answer.
    2. Allows aluminum conductors to replace copper conductors
    3. Eliminates the need for a constant-speed drive
    4. Reduces the voltage required for a given amount of power

    Explanation

    Magnetic devices can be built smaller for a given power level as frequency increases, which saves weight on aircraft. The higher frequency is produced by a constant-speed drive or an inverter because the weight saving is worth the added complexity.

  26. Question 26General

    The unit of electrical power in the SI system is the

    1. volt
    2. ohm
    3. watt Correct answer.
    4. ampere

    Explanation

    Electrical power is the rate at which electrical energy is transferred and is measured in watts. One watt equals one joule per second, or one volt times one ampere.

  27. Question 27General

    The grip length of an aircraft bolt is measured from the underside of the head to the

    1. end of the threads
    2. center of the shank
    3. start of the threads Correct answer.
    4. top of the head

    Explanation

    Grip length covers the unthreaded shank portion that passes through the parts being joined. It is measured from the bearing surface under the head to the first thread.

  28. Question 28General

    Which extinguishing agent is appropriate for a fire involving magnesium?

    1. carbon dioxide from a CO2 extinguisher
    2. Class D dry powder Correct answer.
    3. water spray from a pressurized can
    4. aqueous foam solution

    Explanation

    Magnesium is a combustible metal, and combustible metal fires require a Class D extinguishing agent. Water and ordinary foam can react violently with burning magnesium. Carbon dioxide is not effective for deep-seated metal fires.

  29. Question 29General

    A torque wrench is used to

    1. measure twisting force applied to a fastener Correct answer.
    2. check the hardness of the fastener threads
    3. measure the stretch of the bolt shank directly
    4. measure the pitch of the fastener threads

    Explanation

    A torque wrench controls the amount of turning effort applied to a fastener. It indicates torque, which is force multiplied by lever arm, rather than bolt stretch or thread dimensions.

  30. Question 30General

    MIL-PRF-5606 mineral-base hydraulic fluid is normally colored

    1. red Correct answer.
    2. blue
    3. green
    4. clear

    Explanation

    MIL-PRF-5606 hydraulic fluid is dyed red to help identify it and distinguish it from other fluids. Color coding assists in preventing the wrong fluid from being added to a system.

  31. Question 31General

    Nitrogen is often used to inflate aircraft tires because it

    1. reduces fire hazard and moisture in the tire Correct answer.
    2. makes the tire assembly noticeably lighter
    3. increases the tire pressure automatically as it warms
    4. eliminates the need for any future pressure check

    Explanation

    Nitrogen is dry and does not support combustion, so it reduces the risk of a tire fire and minimizes moisture inside the wheel assembly. It does not eliminate the need for routine pressure checks.

  32. Question 32General

    The most common cause of corrosion on aircraft structures is

    1. vibration
    2. heat
    3. fuel
    4. moisture Correct answer.

    Explanation

    Moisture, often combined with salt or other contaminants, is the primary environmental factor that promotes corrosion. Corrosion control therefore focuses on preventing water accumulation and maintaining protective coatings.

  33. Question 33General

    An adjustable torque wrench should be stored

    1. at its lowest setting Correct answer.
    2. at any setting
    3. at its mid-range setting
    4. at its maximum setting

    Explanation

    Storing an adjustable torque wrench at its lowest setting relieves spring tension and helps preserve calibration. A wrench left compressed can take a set and lose accuracy.

  34. Question 34General

    A micrometer sleeve reads 0.200 inch and the thimble is on the 18th division. If the thimble has 25 divisions and one revolution advances 0.025 inch, the reading is

    1. 0.238 in
    2. 0.380 in
    3. 0.218 in Correct answer.
    4. 0.200 in

    Explanation

    Each thimble division represents 0.025 inch divided by 25, or 0.001 inch. Adding 18 divisions to the sleeve reading gives 0.200 + 0.018 = 0.218 inch.

  35. Question 35General

    A torque wrench is fitted with a crow's foot extension in line with the handle. To apply the specified torque at the fastener, the wrench setting should be

    1. converted to inch-pounds only
    2. decreased Correct answer.
    3. left unchanged
    4. increased

    Explanation

    An in-line extension increases the effective lever arm, so the wrench would otherwise apply more torque at the fastener than it indicates. The wrench setting must therefore be reduced according to the adapter formula.

  36. Question 36General

    In a series circuit containing three resistors, the current

    1. is divided among the resistors in proportion to resistance
    2. is the same at every point in the circuit Correct answer.
    3. equals the sum of all the voltage drops around the circuit
    4. is greatest across the largest resistor in the circuit

    Explanation

    A series circuit has only one path for current, so the same current flows through every component. The voltage drops divide in proportion to resistance.

  37. Question 37General

    A 12-volt battery is connected across a 3-ohm resistor. What power is dissipated by the resistor?

    1. 36 W
    2. 48 W Correct answer.
    3. 12 W
    4. 4 W

    Explanation

    Power can be found from P = V squared divided by R. Substituting gives 144 divided by 3, or 48 watts.

  38. Question 38General

    The empty weight and empty-weight center of gravity for a specific aircraft are normally recorded in the

    1. pilot's operating handbook limitations section
    2. type certificate data sheet only
    3. FAA registration certificate
    4. aircraft weight and balance report Correct answer.

    Explanation

    The weight and balance report documents the actual as-weighed empty weight and empty-weight center of gravity for that individual aircraft. It also records the arm and moment of each installed item.

  39. Question 39General

    The primary purpose of electrical bonding in an aircraft is to

    1. provide a low-resistance path for static and fault current Correct answer.
    2. reduce the overall weight of the electrical system
    3. allow aluminum wire to be used in place of copper wire
    4. increase the structural strength of the airframe assembly

    Explanation

    Bonding connects conductive structures so that static charges and fault currents have a low-resistance path. This helps protect against sparks, lightning damage, and electrical shock hazards.

  40. Question 40General

    When safety wiring two adjacent bolts, the wire should be installed so that

    1. the wire is twisted only at the ends of the run
    2. loosening pulls the wire toward tightening Correct answer.
    3. the wire is left loose so that it can flex with vibration
    4. the wire passes over the head of each bolt without tension

    Explanation

    Safety wire is routed so that any tendency of a fastener to loosen applies tension in the tightening direction. This keeps the wire taut and opposes rotation.

  41. Question 41General

    The datum used for aircraft weight and balance calculations is

    1. the forward limit of the center of gravity range
    2. an arbitrary manufacturer-selected reference point Correct answer.
    3. the main landing gear axle centerline
    4. the center of gravity of the empty aircraft

    Explanation

    The datum is an arbitrary reference point chosen by the manufacturer from which arms are measured. It may be located ahead of, behind, or within the aircraft.

  42. Question 42General

    A maintenance record entry for a major repair must include at least the

    1. aircraft total time and the shop name
    2. parts cost and the customer's signed receipt
    3. description, date, signature, and certificate number Correct answer.
    4. total labor hours and the date work started

    Explanation

    Maintenance records must describe the work performed, the date, and identify the person approving the work. For certified mechanics, the signature and certificate number provide that identification.

  43. Question 43General

    Major repairs and major alterations are defined in

    1. Part 39
    2. Part 43, Appendix A Correct answer.
    3. Part 65, Appendix B
    4. Part 91, Appendix D

    Explanation

    14 CFR Part 43, Appendix A, lists the work considered a major repair or major alteration. This classification affects what records and approvals are required.

  44. Question 44General

    The inside diameter of an engine cylinder bore is best measured with an

    1. inside micrometer or bore gauge Correct answer.
    2. vernier caliper
    3. feeler gauge
    4. outside micrometer

    Explanation

    An inside micrometer or a bore gauge is designed to measure internal diameters accurately. A telescoping gauge used with an outside micrometer is another acceptable method.

  45. Question 45General

    Aircraft fabric dope is applied primarily to

    1. provide color only and not affect the fabric
    2. shrink the fabric taut and form a base for finish Correct answer.
    3. clean the fabric and remove all old dope
    4. waterproof the fabric without affecting tautness

    Explanation

    Dope shrinks as it dries, tightening the fabric over the structure. It also builds a base to which subsequent coats and finishes can adhere.

  46. Question 46General

    Eddy current inspection is most useful for detecting

    1. magnetic flux leakage in ferromagnetic parts
    2. corrosion products trapped under paint
    3. surface and near-surface defects in conductive metals Correct answer.
    4. internal voids deep inside thick castings

    Explanation

    Eddy currents are induced in conductive materials and are disturbed by discontinuities near the surface. The method is therefore suited to cracks and similar flaws in conductive metals.

  47. Question 47General

    When 2024-T4 aluminum alloy is cold worked beyond its yield point, the material

    1. loses all resistance to corrosion
    2. returns to the annealed condition
    3. becomes softer and more ductile
    4. increases in strength and decreases in ductility Correct answer.

    Explanation

    Cold working strains the crystal structure and increases dislocation density, which raises strength. The same deformation reduces the amount of elongation the material can sustain before fracture.

  48. Question 48General

    An alternator must produce 400 Hz when driven at 6,000 rpm. How many poles does it need?

    1. 12 poles
    2. 8 poles Correct answer.
    3. 10 poles
    4. 6 poles

    Explanation

    Frequency equals poles times rpm divided by 120. Rearranging gives poles = 120 times frequency divided by rpm, so 120 times 400 divided by 6,000 equals 8 poles.

  49. Question 49General

    A 12-volt, 24-ampere-hour battery supplies a 48-watt load. Ignoring losses, how long can it supply the load?

    1. 3 hours
    2. 6 hours Correct answer.
    3. 5 hours
    4. 2 hours

    Explanation

    The load current is 48 watts divided by 12 volts, or 4 amperes. Dividing the 24-ampere-hour capacity by 4 amperes gives 6 hours.

  50. Question 50General

    In a sheet metal bend, the neutral axis is the location where the metal is

    1. at the neutral axis Correct answer.
    2. at the inner surface of the bend
    3. at the outer surface of the bend
    4. at the edge of the sheet

    Explanation

    The neutral axis lies within the bend where the material is neither stretched nor compressed. Material outside this axis is in tension, while material inside is in compression.

  51. Question 51General

    Under FAA regulations, which person is authorized to perform an annual inspection of an aircraft and approve it for return to service?

    1. Any certificated airframe and powerplant mechanic
    2. A certificated repairman employed by an approved flight school
    3. A certificated airframe mechanic who holds an Inspection Authorization Correct answer.
    4. A certificated private pilot holding a current medical certificate

    Explanation

    Annual inspections are a specific privilege granted only to mechanics who hold an Inspection Authorization in addition to their airframe and powerplant ratings. The IA holder is the only one who may sign off the annual inspection and return the aircraft to service. A mechanic without the authorization may perform the work but cannot approve it.

  52. Question 52General

    An item weighing 40 pounds is located 25 inches aft of the datum. What is its moment?

    1. 1,000 pound-inches Correct answer.
    2. 65 pound-inches
    3. 10,000 pound-inches
    4. 1.6 pound-inches

    Explanation

    Moment is the product of weight and arm, so 40 pounds multiplied by 25 inches gives 1,000 pound-inches. Moments are added and subtracted algebraically about the datum to locate the center of gravity. Multiplying instead of dividing is essential because arm is already expressed in inches from the datum.

  53. Question 53General

    A fuse or circuit breaker is installed in an aircraft electrical circuit primarily to

    1. open the circuit and protect the wiring from overheating Correct answer.
    2. convert alternating current to direct current
    3. regulate the voltage supplied to the bus bar
    4. block reverse current flow into the battery

    Explanation

    A fuse or circuit breaker is a protective device that opens the circuit when current exceeds a set value, limiting heat in the conductor. Wiring is sized for a maximum current, and the protective device must be chosen so the wire is never asked to carry more than it can safely dissipate. Voltage regulation and rectification are separate functions performed by other components.

  54. Question 54General

    On an aircraft drawing, the term tolerance refers to the

    1. total allowable variation from a specified dimension Correct answer.
    2. clearance remaining between two mating parts after assembly
    3. ratio between the drawing scale and the actual size of the part
    4. amount a part shrinks after heat treatment

    Explanation

    Tolerance states how far a manufactured dimension may legally deviate from the dimension called out on the drawing. It may be expressed as a plus-or-minus value or as a pair of limit dimensions. Anything within the tolerance band is acceptable and anything outside it is a rejectable part.

  55. Question 55General

    Which extinguishing agent is appropriate for a fire involving energized electrical equipment in an aircraft?

    1. Aqueous film-forming foam
    2. Carbon dioxide Correct answer.
    3. Water
    4. Wet chemical (potassium acetate)

    Explanation

    Carbon dioxide smothers the fire without leaving a residue and, unlike water or foam, does not conduct electricity back to the technician. It is the standard choice for electrical fires because the agent is nonconductive and leaves no cleanup problem in avionics or wiring. Water-based agents and wet chemicals are intended for Class A and Class K fires respectively.

  56. Question 56General

    The grip length of a standard aircraft bolt is the

    1. shank diameter multiplied by the thread pitch
    2. length of the threaded portion of the shank
    3. distance from the underside of the head to the start of the threads Correct answer.
    4. overall length of the bolt measured through the head

    Explanation

    Grip length describes the unthreaded portion of the shank that passes through the material being joined, measured from the bearing surface under the head to the first thread. The bolt is selected so the grip matches the total thickness of the parts, keeping the threads out of the shear plane. Overall length and thread length are separate dimensions.

  57. Question 57General

    The flared end of a standard AN flared tube is formed at an angle of

    1. 37 degrees Correct answer.
    2. 60 degrees
    3. 30 degrees
    4. 45 degrees

    Explanation

    AN and AC flared tube fittings used in aircraft plumbing use a 37-degree flare so the flare seats against the matching cone of the fitting. Automotive-type flares are made at 45 degrees and must not be substituted. Using the wrong flare angle prevents proper sealing and can cause a leak or a cracked flare.

  58. Question 58General

    The purpose of anodizing an aluminum alloy part is to

    1. build up a hard, corrosion-resistant oxide film on the surface Correct answer.
    2. remove surface scratches left by machining
    3. restore the alloy to its heat-treated condition
    4. soften the surface so it can be polished more easily

    Explanation

    Anodizing is an electrolytic process that thickens the natural oxide layer on aluminum, producing a hard film that resists corrosion and provides a good base for paint. The coating is integral to the surface rather than applied on top of it. It does not change the strength or temper of the underlying alloy.

  59. Question 59General

    Fretting corrosion is most likely to occur

    1. along the grain boundaries inside a cast aluminum fitting
    2. at the interface of two mating surfaces that move slightly against each other Correct answer.
    3. on the interior surfaces of an integral fuel tank
    4. on a bare steel surface that stays continuously wet

    Explanation

    Fretting corrosion results from small relative movement between closely fitting parts, such as riveted lap joints or bolted flanges, which breaks down the protective film and exposes fresh metal. The resulting dark powder and pitting appear exactly at the contact faces. Access to the joint and removal of the fastener are usually needed to find and correct it.

  60. Question 60General

    Liquid penetrant inspection is used to detect

    1. internal voids deep within a casting
    2. variations in hardness of a heat-treated part
    3. subsurface cracks in ferromagnetic steel
    4. surface-breaking discontinuities in nonporous materials Correct answer.

    Explanation

    Penetrant inspection relies on a liquid drawn by capillary action into openings that reach the surface, so it reveals only surface-connected defects. The material must be nonporous so the penetrant can be cleaned from the surface without being trapped in unrelated porosity. Subsurface flaws require a volumetric method such as radiography or ultrasonic inspection.

  61. Question 61General

    Under 14 CFR Part 43, maintenance on an aircraft must be performed using

    1. the methods, techniques, and practices in the current manufacturer's maintenance manual or other instructions acceptable to the Administrator Correct answer.
    2. any procedure the mechanic has found through experience to produce a satisfactory result
    3. only procedures printed in FAA Advisory Circulars
    4. the procedures listed in the aircraft's type certificate data sheet

    Explanation

    Part 43 requires that maintenance be done in accordance with the current manufacturer's maintenance manual or instructions acceptable to the FAA, so that work is accomplished to a known standard. Personal practice or convenience is not a substitute for approved data. Advisory circulars may provide guidance, but they do not by themselves define every approved procedure.

  62. Question 62General

    A stop hole is drilled at the end of a small crack in aircraft sheet metal in order to

    1. allow the length of the crack to be measured more accurately
    2. serve as a pilot hole for the replacement rivet
    3. prepare the crack for welding
    4. relieve the stress concentration and keep the crack from spreading Correct answer.

    Explanation

    A crack tip is a point of very high stress concentration, and drilling a smooth round hole removes that tip and redistributes the load around the hole. This slows or halts further propagation and is typically followed by an approved repair. Drilling is a temporary measure; the crack still requires evaluation and repair per approved data.

  63. Question 63General

    Which method is proper for cleaning acrylic aircraft windows?

    1. Polishing with an abrasive compound to remove light scratches
    2. Wiping the surface with a dry shop rag to remove dust
    3. Rubbing the surface with methyl ethyl ketone on a soft cloth to remove grease
    4. Washing with mild soap and water and then flushing with clean water Correct answer.

    Explanation

    Acrylic glazing is softened and crazed by many solvents, so the recommended practice is plenty of clean water with a mild soap to float away dirt. The surface should be flushed before any wiping so grit is not dragged across the plastic. Solvents and dry rubbing both damage or scratch the surface.

  64. Question 64General

    An aircraft weighs 3,000 pounds with its center of gravity at station 80. A 150-pound item is moved from station 60 to station 120. What is the new center of gravity location?

    1. Station 89.0
    2. Station 80.5
    3. Station 83.0 Correct answer.
    4. Station 86.0

    Explanation

    Moving weight within the aircraft leaves total weight unchanged but shifts the center of gravity by the weight moved times the distance moved, divided by total weight: 150 times 60 divided by 3,000 equals 3 inches. Because the item moves aft, the center of gravity moves aft from station 80 to station 83. Total weight does not change during an internal shift of this kind.

  65. Question 65General

    A hydraulic actuator piston has a diameter of 4 inches and is supplied with 500 psi. What force does it produce?

    1. Approximately 2,000 pounds
    2. Approximately 1,571 pounds
    3. Approximately 6,283 pounds Correct answer.
    4. Approximately 12,566 pounds

    Explanation

    Force equals pressure times area, and the area of a 4-inch-diameter piston is pi times the radius squared, or about 12.57 square inches. Multiplying 12.57 square inches by 500 psi gives about 6,283 pounds of force. Using the diameter in place of the radius, or using circumference, gives the other answers.

  66. Question 66General

    A 12-volt source is connected across a 6-ohm resistor and a 3-ohm resistor wired in parallel. What total current flows from the source?

    1. 4 amperes
    2. 2 amperes
    3. 1.33 amperes
    4. 6 amperes Correct answer.

    Explanation

    In a parallel circuit each branch sees the full source voltage, so the 6-ohm branch draws 12 divided by 6, or 2 amperes, and the 3-ohm branch draws 12 divided by 3, or 4 amperes. The total current from the source is the sum of the branch currents, 6 amperes. The equivalent resistance of the pair is 2 ohms, which also gives 12 divided by 2 equals 6 amperes.

  67. Question 67Airframe

    A separation of wood fibers running parallel to the grain along the length of a wooden spar is called

    1. a check Correct answer.
    2. a shake
    3. a knot
    4. compression wood

    Explanation

    A check is a lengthwise crack that opens along the grain as the wood dries; it does not cross the grain. Shakes separate between annual growth rings, and knots are the bases of branches embedded in the wood. Compression wood is abnormally dense wood formed on the underside of a leaning trunk.

  68. Question 68Airframe

    The primary purpose of rib stitching on a fabric-covered wing is to

    1. hold the fabric taut while the dope dries
    2. prevent the fabric from shrinking after doping
    3. secure the fabric to the ribs so it carries the aerodynamic loads Correct answer.
    4. provide a continuous electrical bond between the fabric and the structure

    Explanation

    Rib stitching ties the fabric to each wing rib so that the lifting loads on the fabric are transferred into the structure. Dope supplies tautness and the bond to the structure, but neither can carry the aerodynamic load. Stitching is therefore a structural attachment, not a finishing step.

  69. Question 69Airframe

    Which fastener is used to join sheet metal where access to only one side of the work is available?

    1. A blind rivet Correct answer.
    2. A Hi-Lok collar fastener
    3. A countersunk AN bolt
    4. A solid universal-head rivet

    Explanation

    Blind rivets are set by pulling or expanding a stem that is installed entirely from the accessible side. Solid rivets, Hi-Lok fasteners, and bolts all require a bucking bar, collar, or nut to be placed on the far side. Blind fasteners are therefore chosen for enclosed structures such as wing trailing edges.

  70. Question 70Airframe

    Fretting corrosion occurs

    1. between close-fitting parts that fret under vibration Correct answer.
    2. on magnesium parts exposed to salt spray
    3. where two dissimilar metals touch in an electrolyte
    4. along the grain boundaries of heat-treated aluminum

    Explanation

    Fretting corrosion is the breakdown of protective films where two tightly mated surfaces rub together under vibration, such as bolted joints and bearing fits. The rubbing exposes fresh metal, which then oxidizes and can lead to fatigue cracking. It is not an electrochemical dissimilar-metal effect.

  71. Question 71Airframe

    In an oleo (air-oil) shock strut, the landing shock is absorbed by

    1. compressed air alone, with the oil acting only as a lubricant
    2. a coil spring inside the piston tube
    3. oil being forced through an orifice as the strut compresses Correct answer.
    4. rubber shock pads stacked in the cylinder

    Explanation

    As the strut compresses, oil is forced through a metering orifice, converting kinetic energy into heat, while the compressed air or nitrogen provides the spring action. The orifice restriction is what damps the stroke and prevents a hard bottoming. Oil therefore does the damping work and gas does the spring work.

  72. Question 72Airframe

    The component used to allow hydraulic fluid to flow in one direction only is a

    1. check valve Correct answer.
    2. pressure relief valve
    3. selector valve
    4. shuttle valve

    Explanation

    A check valve is a one-way valve that opens with flow in the permitted direction and seats against reverse flow. Selector valves direct flow to a chosen actuator, and relief valves limit pressure. A shuttle valve selects the higher of two pressure sources rather than blocking reverse flow.

  73. Question 73Airframe

    The function of a circuit breaker in an aircraft electrical system is to

    1. convert alternating current to direct current
    2. limit the voltage supplied to a component
    3. open the circuit when current exceeds a rated value Correct answer.
    4. provide a ground path for static electricity

    Explanation

    A circuit breaker is a resettable protective device that trips open when current exceeds its rating, protecting wiring from overheating. Voltage regulation is the job of the voltage regulator, and rectification is done by transformers or rectifier units. Static discharge is handled by static wicks and bonding.

  74. Question 74Airframe

    The type of stress produced when two forces pull a member apart along its length is called

    1. shear
    2. torsion
    3. compression
    4. tension Correct answer.

    Explanation

    Tension is the tensile stress created by forces pulling a member apart along its axis, stretching it. Compression pushes a member together, shear tends to slide one layer past another, and torsion twists the member about its axis. A member in tension elongates until it reaches its ultimate strength.

  75. Question 75Airframe

    A carburizing oxyacetylene flame is characterized by

    1. a blue outer envelope with no visible inner cone
    2. a short, sharp inner cone and an excess of oxygen
    3. a feathery white inner cone and an excess of acetylene Correct answer.
    4. a neutral inner cone with equal parts of both gases

    Explanation

    A carburizing flame has excess acetylene, which shows up as a feathery white secondary cone around the inner cone. An oxidizing flame shows a short, sharp inner cone from excess oxygen, and a neutral flame has equal proportions of the two gases. The type is judged by the appearance of the inner cone.

  76. Question 76Airframe

    For a typical riveted sheet metal repair, the minimum edge distance from the center of a rivet to the edge of the sheet is

    1. four rivet diameters
    2. six rivet diameters
    3. two rivet diameters Correct answer.
    4. one rivet diameter

    Explanation

    Standard practice sets the minimum edge distance at two rivet diameters, measured from the rivet center to the edge of the sheet. Less than that risks tearing the sheet out at the edge, while much greater distances waste material and can cause sheet buckling. Rivet pitch, a separate dimension, is normally three to four diameters.

  77. Question 77Airframe

    In a bonded repair of a fiberglass laminate, the damaged area is tapered (scarfed) primarily to

    1. allow the patch to be clamped flat
    2. reduce the weight of the finished repair
    3. spread the load gradually into the surrounding laminate Correct answer.
    4. remove all traces of the original resin

    Explanation

    A scarf tapers the repair so that the load is transferred gradually from the patch into the parent laminate over a large bond area, avoiding a stress concentration at the edge of the repair. The taper angle is chosen from the strength required and the allowable shear stress of the adhesive. Simply removing resin or saving weight is not the purpose of the taper.

  78. Question 78Airframe

    A pressure relief valve in an aircraft hydraulic system is installed to

    1. prevent fluid from flowing back to the reservoir
    2. bypass fluid when the system pressure drops
    3. maintain a constant pump output flow
    4. limit system pressure to a safe maximum value Correct answer.

    Explanation

    A relief valve opens at a preset pressure and returns fluid to the reservoir so system pressure cannot exceed a safe limit. It protects components and lines from overpressure caused by thermal expansion or a blocked circuit. Flow control and anti-reverse functions belong to other valves.

  79. Question 79Airframe

    The shimmy damper installed on a nose landing gear is intended to

    1. absorb the vertical landing impact
    2. damp out oscillations of the nose wheel during ground roll Correct answer.
    3. keep the wheel centered during retraction
    4. retract the gear after takeoff

    Explanation

    A shimmy damper resists rapid back-and-forth rotation of the nose wheel assembly, preventing the violent oscillation known as shimmy during taxi and landing roll. It does not carry vertical loads; the shock strut does that. Retraction and centering are handled by the actuating cylinder and centering cams.

  80. Question 80Airframe

    Fuel tanks are vented to the atmosphere primarily to

    1. provide air for combustion in the carburetor
    2. permit rapid defueling of the aircraft
    3. prevent a pressure differential that could collapse or rupture the tank Correct answer.
    4. allow fuel vapor to escape so the fuel stays cool

    Explanation

    As fuel is burned, a vent lets air into the tank to keep internal pressure near ambient, and it lets air out as the tank is filled. Without venting, the pressure differential could collapse a tank or, in the other direction, rupture it. Combustion air is supplied separately through the induction system.

  81. Question 81Airframe

    Most thermal anti-ice systems on transport category aircraft wings use

    1. hot engine bleed air ducted through the leading edge Correct answer.
    2. a chemical deicing fluid pumped onto the surface
    3. pneumatic boots that inflate to break the ice
    4. electrical heating elements bonded to the leading edge

    Explanation

    Thermal anti-ice systems duct hot compressor bleed air through the leading edge of the wing and empennage to keep the surface above freezing so ice cannot form. Pneumatic boots are a deicing system that removes ice after it forms, and chemical systems are used mainly on propellers and on some smaller aircraft. Electrically heated leading edges are used on some aircraft but are less common on large transport wings.

  82. Question 82Airframe

    The extinguishing agent most commonly used in aircraft engine compartment fire extinguishing systems is

    1. water
    2. dry chemical powder
    3. Halon 1301 Correct answer.
    4. carbon dioxide snow

    Explanation

    Halon 1301 is a clean, electrically nonconductive agent that leaves no residue, which makes it well suited to engine and APU compartments. It interrupts the combustion chain reaction and is discharged as a gas that floods the compartment. Water, dry powder, and carbon dioxide snow leave residue or provide poor distribution in an engine nacelle.

  83. Question 83Airframe

    The dihedral angle of a wing is the angle between the wing and

    1. the longitudinal axis in plan view
    2. a horizontal plane Correct answer.
    3. the wing chord line at the tip
    4. the aircraft vertical axis

    Explanation

    Dihedral is measured between the wing and a horizontal plane, giving the wing its upward slant from root to tip. Sweep angle is measured in plan view relative to the lateral axis, and incidence is the angle between the chord line and the longitudinal axis. Dihedral contributes to lateral (roll) stability.

  84. Question 84Airframe

    An aircraft loaded so that its center of gravity is ahead of the forward limit will tend to exhibit

    1. high control forces and difficulty in flaring for landing Correct answer.
    2. an increase in useful load and range
    3. a tail-heavy condition and light elevator forces
    4. reduced longitudinal stability

    Explanation

    A forward CG increases the nose-down moment and the distance from the CG to the tail, so the elevator must produce more downforce, raising stick forces and making rotation and flare difficult. Longitudinal stability actually increases as the CG moves forward. A tail-heavy condition results from an aft CG.

  85. Question 85Airframe

    The voltage regulator in a DC generating system controls

    1. the speed of the generator drive
    2. the generator field current to hold output voltage constant Correct answer.
    3. the frequency of the generator output
    4. the current drawn by the battery

    Explanation

    The voltage regulator varies the field current of the generator so that its output voltage stays at the regulated value as load and speed change. Frequency and drive speed depend on the engine and the generator's drive ratio. Battery charging current is a consequence of the regulated voltage, not the regulated variable.

  86. Question 86Airframe

    The cabin outflow valve in a pressurized aircraft controls

    1. the flow of bleed air into the cabin
    2. the rate at which air leaves the cabin, and thus cabin pressure Correct answer.
    3. the amount of fresh air mixed with recirculated air
    4. the temperature of the air entering the cabin

    Explanation

    Cabin pressure is maintained by controlling how fast air leaves the cabin, which is the job of the outflow valve. Inflow through the bleed-air system is essentially fixed, so modulating the outflow sets the pressure altitude and rate of change. Temperature and mixing are handled by the air conditioning and recirculation systems.

  87. Question 87Airframe

    When gas tungsten arc welding aluminum, alternating current is used because it

    1. keeps the weld puddle from solidifying too rapidly
    2. prevents the tungsten electrode from ever contacting the workpiece, which would contaminate the weld
    3. eliminates the need for a shielding gas during the welding operation
    4. provides oxide cleaning on one half of the cycle and penetration on the other Correct answer.

    Explanation

    On alternating current the electrode-positive half cycle bombards the work with positive ions, breaking up the refractory aluminum oxide, while the electrode-negative half cycle carries most of the heat into the weld for penetration. Direct current would give either cleaning or penetration but not both in balance. Shielding gas and electrode technique are still required.

  88. Question 88Airframe

    An aircraft has an empty weight of 1,400 pounds with a center of gravity at station 40. A 200-pound crate is then loaded at station 60. The new center of gravity is at station

    1. 42.5 Correct answer.
    2. 50.0
    3. 44.0
    4. 41.0

    Explanation

    Total moment is (1,400 x 40) + (200 x 60) = 56,000 + 12,000 = 68,000 pound-inches, and total weight is 1,600 pounds. Dividing gives 68,000 / 1,600 = 42.5 inches. The CG moves toward the added weight but only partway, as expected.

  89. Question 89Airframe

    In a wing spar, the spar caps carry bending loads while the web carries

    1. torsion loads
    2. bending loads
    3. tension loads
    4. shear loads Correct answer.

    Explanation

    The spar caps act as the flanges of a beam and take the tension and compression produced by bending, while the web resists the shear between them. Torsion is carried by the closed torque box formed by the skin, ribs, and spar web together. This division of labor is why cap area and web thickness are sized by different loads.

  90. Question 90Airframe

    A reverse-current cutout relay in a DC generator circuit protects the system by

    1. regulating the strength of the generator field
    2. opening the circuit when generator voltage falls below battery voltage Correct answer.
    3. limiting generator output to a safe value
    4. disconnecting the battery from the bus during overvoltage

    Explanation

    If generator voltage drops below battery voltage, current would flow from the battery back through the generator and damage it, so the cutout relay opens the generator-to-battery circuit. It closes only when generator voltage rises above battery voltage. Overvoltage and field regulation are handled by other components.

  91. Question 91Airframe

    When a bolt is installed in a joint loaded in shear, it should be selected and installed so that

    1. a castellated nut is used without a cotter pin
    2. the threads bear directly on the shear plane for a tighter fit
    3. the threads are outside the shear plane and the shank bears the load Correct answer.
    4. at least two threads are inside the shear plane

    Explanation

    The full-diameter shank, not the threaded portion, must bear in the shear plane because the reduced root area of the threads lowers the joint's shear strength. The bolt is chosen so that no more than a light thread runout falls within the shear plane. Castellated nuts always require a cotter pin or equivalent safety.

  92. Question 92Airframe

    The control surface that rotates an aircraft about its longitudinal axis is the

    1. Stabilator
    2. Rudder
    3. Elevator
    4. Aileron Correct answer.

    Explanation

    Rotation about the longitudinal axis is roll, and roll is produced by the ailerons. The elevator controls pitch about the lateral axis, and the rudder controls yaw about the vertical axis.

  93. Question 93Airframe

    Aircraft tires are normally inflated with dry nitrogen rather than compressed air primarily to

    1. reduce the unsprung weight of the landing gear assembly
    2. maintain a constant inflation pressure at all altitudes
    3. allow the tire to be operated at higher ground speeds
    4. reduce the fire hazard inside the wheel assembly Correct answer.

    Explanation

    Nitrogen is dry and does not support combustion, so it removes the oxygen that could feed a fire if a brake or wheel overheats. It also avoids the moisture and pressure variation associated with compressed air.

  94. Question 94Airframe

    The nondestructive inspection method that uses a fluorescent dye and ultraviolet light to locate surface defects is

    1. Eddy current inspection
    2. Fluorescent penetrant inspection Correct answer.
    3. Ultrasonic inspection of thick sections
    4. Magnetic particle inspection

    Explanation

    Fluorescent penetrant inspection relies on a dye that seeps into surface openings and glows under ultraviolet light. Magnetic particle inspection is limited to ferromagnetic materials and does not use ultraviolet light to reveal the indication in this manner.

  95. Question 95Airframe

    On a flat sheet metal layout, the bend tangent lines indicate the

    1. centerline of the bend radius
    2. neutral axis of the bend
    3. outside mold line of the part
    4. start of the bend radius Correct answer.

    Explanation

    The bend tangent line is drawn where the flat portion of the layout becomes tangent to the bend radius, which is where the bend begins. The bend allowance measured between the two bend tangent lines gives the amount of material consumed by the bend.

  96. Question 96Airframe

    The component used to adjust the tension of an aircraft control cable is the

    1. Turnbuckle Correct answer.
    2. Fork end
    3. Bushing
    4. Thimble

    Explanation

    A turnbuckle has right- and left-hand threaded ends so that rotating the barrel shortens or lengthens the cable run to set tension. After adjustment it must be safety-wired or clipped to prevent rotation.

  97. Question 97Airframe

    The torque links on a landing gear strut

    1. keep the wheel aligned and transmit braking torque Correct answer.
    2. provide steering input to the nose wheel
    3. limit the maximum extension travel of the strut piston
    4. absorb the initial landing shock loads before the strut

    Explanation

    Torque links connect the strut cylinder to the piston so the piston cannot rotate, holding the wheel in alignment and carrying brake torque into the strut. The links pivot to allow the piston to move in and out.

  98. Question 98Airframe

    The extinguishing agent preferred for an electrical fire in an avionics compartment because it leaves no residue is

    1. Water
    2. Dry chemical powder
    3. Carbon dioxide Correct answer.
    4. AFFF foam

    Explanation

    Carbon dioxide is nonconductive and evaporates without leaving residue that could damage avionics. Water and foam are conductive, and dry chemical powder leaves a corrosive residue.

  99. Question 99Airframe

    On most transport category aircraft, the air used to pressurize the cabin is obtained from

    1. compressor bleed air from the engines Correct answer.
    2. an electrically driven cabin compressor unit
    3. an engine-driven cabin supercharger
    4. a ram-air scoop and an air cycle machine

    Explanation

    Turbine-engine aircraft tap bleed air from the engine compressor, then condition it through flow control and air-cycle cooling before it enters the cabin. Cabin pressure is regulated by controlling how much of that air leaves through the outflow valve.

  100. Question 100Airframe

    While in cruise, the bypass indicator button on a hydraulic system filter extends. This indicates that

    1. system pressure has exceeded the relief valve setting
    2. the element has been bypassing since the last inspection
    3. fluid temperature has exceeded the normal operating range
    4. the element is restricted and fluid is bypassing it Correct answer.

    Explanation

    A differential pressure indicator pops when the pressure drop across a clogged element exceeds its set value, meaning fluid is flowing through the bypass. The filter should be serviced and the indicator reset before further flight.

  101. Question 101Airframe

    A vacuum bag is used over a composite repair layup to

    1. align the ply orientation with the primary load direction
    2. cure the resin at a controlled temperature and rate
    3. hold the repair at a constant humidity while curing
    4. compact the laminate and remove air and excess resin Correct answer.

    Explanation

    The bag applies atmospheric pressure over the repair, consolidating the plies and drawing out trapped air and surplus resin through the bleeder. Better compaction reduces voids and produces a stronger, more uniform bond.

  102. Question 102Airframe

    Control cable tension is set with the aircraft at the temperature specified in the maintenance manual because cable tension

    1. must always be set before the aircraft is rigged
    2. is affected only by the amount of wear in the pulleys
    3. changes as the structure and cables expand at different rates Correct answer.
    4. increases permanently each time the system is fully cycled

    Explanation

    Aluminum structure and steel cable have different coefficients of thermal expansion, so a given rig tension changes as the aircraft changes temperature. Setting tension at the specified temperature ensures the tension will be correct in the operating range.

  103. Question 103Airframe

    When seating the beads of a tubeless tire that has just been installed on a wheel assembly, the mechanic should

    1. use a remote inflation hose and stay clear of the bead area Correct answer.
    2. tap the sidewall with a mallet while the tire is being inflated
    3. inflate the tire slowly while a helper holds the wheel upright
    4. lubricate the beads with soap solution and inflate rapidly

    Explanation

    A bead that has not fully seated can release violently, so the wheel is inflated with a remote hose or in a safety cage with personnel clear of the bead plane. The wheel is then checked for proper bead seating before the hose is removed.

  104. Question 104Airframe

    The two primary factors considered when selecting the size of wire for an aircraft circuit are

    1. circuit breaker rating and wire length only
    2. number of terminals and type of conduit
    3. insulation type and color code
    4. current-carrying capacity and allowable voltage drop Correct answer.

    Explanation

    The wire must be large enough to carry the load current without overheating and large enough to keep voltage drop within limits at the load. Bundling, altitude, and temperature then require further derating of the chosen size.

  105. Question 105Airframe

    Before fueling begins, the fuel nozzle is bonded to the aircraft to

    1. prevent fuel from siphoning back through the nozzle
    2. provide a ground path for the aircraft electrical system
    3. equalize electrical potential and prevent a static spark Correct answer.
    4. discharge the fuel's accumulated heat into the structure

    Explanation

    Bonding places the nozzle and the airframe at the same electrical potential so that static charge generated by fuel flow cannot arc at the filler opening. The aircraft must also be grounded to earth before fueling.

  106. Question 106Airframe

    An aircraft is loaded so that its CG falls aft of the aft limit. This condition can be corrected by

    1. moving load or ballast forward of the current CG Correct answer.
    2. adding ballast at a station aft of the original CG
    3. removing weight from a station forward of the original CG
    4. increasing the gross weight without changing the load

    Explanation

    The CG always moves toward any weight added and away from any weight removed, so shifting load or ballast forward brings the CG forward into the envelope. The resulting weight and CG must then be rechecked against both limits.

  107. Question 107Airframe

    A pneumatic deicer boot removes ice from a wing leading edge by

    1. heating the skin electrically to melt the ice bond
    2. inflating to crack the ice so airflow carries it away Correct answer.
    3. sweating alcohol through a porous panel
    4. using engine bleed air to raise the skin temperature rapidly

    Explanation

    The boot inflates and deflates in cycles, flexing the surface so the ice cracks and is swept off by the airstream. The boot does not melt the ice; it breaks the bond mechanically.

  108. Question 108Airframe

    The negative pressure relief valve in a pressurized aircraft cabin opens to

    1. limit the maximum positive cabin differential pressure
    2. prevent external pressure from exceeding cabin pressure Correct answer.
    3. dump cabin pressure rapidly after a decompression
    4. supply fresh air when the outflow valve is closed

    Explanation

    If outside pressure becomes higher than cabin pressure, a negative differential would load the structure in the reverse direction. The negative relief valve opens inward to admit ambient air and relieve that condition.

  109. Question 109Airframe

    When oxyacetylene welding aluminum, the flux is used mainly to

    1. provide a shielding gas around the molten puddle
    2. add alloying elements to the weld puddle
    3. dissolve the oxide film and prevent further oxidation Correct answer.
    4. increase the heat input to the base metal

    Explanation

    Aluminum immediately forms a refractory oxide that melts at a much higher temperature than the base metal, so a flux is applied to dissolve the oxide and exclude air. The flux residue must be removed after welding because it is corrosive.

  110. Question 110Airframe

    The primary purpose of dope applied to a fabric-covered aircraft surface is to

    1. seal the fabric against ultraviolet light only
    2. increase the tensile strength of the cotton fibers
    3. provide a base for primer and topcoat only
    4. tauten the fabric and give it a weather-resistant finish Correct answer.

    Explanation

    Dope shrinks as its solvents evaporate, pulling the fabric taut, and successive coats build a continuous film that protects the fabric. The final coats also carry the ultraviolet protection and color.

  111. Question 111Airframe

    Corrosion is discovered on an aluminum structural fitting. The amount of material that may be blended out is determined by

    1. the diameter and depth of the corrosion blister
    2. the grade of abrasive used to remove the corrosion products
    3. the thickness of the protective coating that was applied
    4. the limits in the manufacturer's structural repair manual Correct answer.

    Explanation

    Structural repair manuals publish allowable blend-out limits and rework procedures for specific parts, and exceeding them affects load-carrying capability. Any removal beyond those limits requires an approved repair or part replacement.

  112. Question 112Airframe

    An aircraft has an empty weight of 2,000 pounds with its CG at station 60. A 300-pound item is removed from station 120. What is the new CG station?

    1. 52.5
    2. 54.0
    3. 49.4 Correct answer.
    4. 45.0

    Explanation

    Total moment before removal is 2,000 x 60 = 120,000 pound-inches; the removed item accounts for 300 x 120 = 36,000 pound-inches. The new moment is 84,000 pound-inches over a new weight of 1,700 pounds, giving a CG of about 49.4.

  113. Question 113Airframe

    With the engine running and the selector valve in neutral, a hydraulic actuator slowly drifts from its set position. The most probable cause is

    1. a restricted return line filter element
    2. internal leakage past the selector valve Correct answer.
    3. low fluid level in the reservoir
    4. external leakage at the actuator rod seal

    Explanation

    In neutral the selector valve blocks both actuator ports; if its internal seals leak, pressurized fluid can bleed into one side of the actuator and let it creep. External leakage would show as fluid loss but would not by itself cause drift.

  114. Question 114Airframe

    The shear strength of a riveted lap joint is limited by the

    1. tensile strength of the rivet heads only
    2. thickness of the outer sheet only
    3. lower of rivet shear strength or sheet bearing strength Correct answer.
    4. number of rivet rows multiplied by the sheet width

    Explanation

    A joint fails either by the rivets shearing or by the sheet tearing or elongating at the holes, so the weaker of the two determines the joint strength. Good design balances rivet shear against the bearing area of the sheet.

  115. Question 115Airframe

    A flight control surface must be rebalanced after it is repainted because paint added aft of the hinge line

    1. changes the surface area and alters the effective trim
    2. increases the hinge moment and makes the controls heavy
    3. increases the stiffness of the surface and reduces its travel
    4. moves the surface CG aft and reduces flutter resistance Correct answer.

    Explanation

    Balance is set so the surface CG is at or ahead of a specified point relative to the hinge line, which suppresses flutter. Weight added behind the hinge line shifts the surface CG aft and can make the surface flutter at speeds within the flight envelope.

  116. Question 116Airframe

    A nickel-cadmium battery that has entered thermal runaway is indicated by

    1. a rapid self-sustaining temperature rise with a high charge current Correct answer.
    2. a low electrolyte level in one cell only
    3. a sulfurous odor with a rise in cell voltage
    4. a gradual drop in cell voltage during discharge

    Explanation

    In thermal runaway the cell's internal resistance drops, so it draws more current, which generates more heat and further lowers resistance; the battery overheats even after charging is stopped. The condition calls for disconnecting the battery and removing it from the aircraft.

  117. Question 117Airframe

    Which type of stress tends to elongate an aircraft structural member?

    1. Torsion
    2. Tension Correct answer.
    3. Shear
    4. Compression

    Explanation

    Tension is the stress that pulls a member along its longitudinal axis and produces elongation. Compression shortens the member, shear tends to slide adjacent layers, and torsion twists it.

  118. Question 118Airframe

    In a sheet metal repair, rivet pitch is the distance between the centers of:

    1. adjacent rivets in the same row Correct answer.
    2. the sheet edge and the first row of rivets
    3. the manufactured head and the shop head
    4. adjacent rows of rivets

    Explanation

    Rivet pitch is measured between the centers of adjacent rivets in the same row. Edge distance is measured from the sheet edge to the rivet center, and transverse pitch is the distance between rows.

  119. Question 119Airframe

    Which aircraft brake design uses alternating stators and rotors to multiply braking force?

    1. Single-disc brake
    2. Expander-tube brake
    3. Drum brake
    4. Multiple-disc brake Correct answer.

    Explanation

    Multiple-disc brakes stack alternating rotors and stators, and hydraulic pressure squeezes the stack to multiply friction. A single-disc brake has one disc pair, a drum brake uses shoes inside a drum, and an expander-tube brake uses a tube to press shoes outward.

  120. Question 120Airframe

    The sump drains on an aircraft fuel tank are opened during preflight to:

    1. vent excess fuel vapor from the tank
    2. measure the fuel quantity in each tank
    3. drain water and sediment from the tank Correct answer.
    4. check fuel pressure at the carburetor

    Explanation

    Sump drains are located at the lowest points of the tank, where water and sediment collect. Draining them during preflight allows contaminants to be removed before flight.

  121. Question 121Airframe

    A shimmy damper installed on a nose landing gear is intended to:

    1. lock the gear in the down position
    2. damp nose wheel oscillation Correct answer.
    3. suppress rapid oscillation of the nose wheel
    4. center the nose wheel after takeoff

    Explanation

    A shimmy damper resists rapid side-to-side oscillation of the nose wheel. It does not center the wheel, lock the gear, or absorb landing impact loads.

  122. Question 122Airframe

    Using the standard shop rule, the total length of a solid rivet should equal the grip length plus:

    1. one-half rivet diameter
    2. two rivet diameters
    3. one and one-half rivet diameters Correct answer.
    4. one rivet diameter

    Explanation

    The common rule for solid rivets is that rivet length equals grip length plus about 1.5 times the rivet diameter. This provides enough material to form a proper shop head.

  123. Question 123Airframe

    Intergranular corrosion in aluminum alloys occurs:

    1. along grain boundaries in the metal Correct answer.
    2. only where dissimilar metals touch
    3. in a narrow band next to a weld
    4. evenly across the surface as a white powder

    Explanation

    Intergranular corrosion attacks along grain boundaries in aluminum alloys, often because of improper heat treatment or exposure to corrosive environments. It may be difficult to see from the surface.

  124. Question 124Airframe

    Which method is most suitable for detecting delamination inside a composite laminate?

    1. Visual inspection only
    2. Dye penetrant inspection
    3. Ultrasonic inspection Correct answer.
    4. Magnetic particle inspection

    Explanation

    Ultrasonic inspection detects internal flaws such as delamination by changes in sound transmission or reflection. Magnetic particle and dye penetrant are surface methods, and visual inspection cannot reveal internal plies.

  125. Question 125Airframe

    A hydraulic system relief valve is installed to:

    1. direct fluid to the actuator during extension
    2. limit maximum system pressure Correct answer.
    3. maintain a constant pump output flow
    4. remove air from the hydraulic fluid

    Explanation

    A relief valve opens when system pressure reaches a set value and returns fluid to the reservoir, limiting maximum pressure. It does not control pump flow, remove air, or direct fluid during normal extension.

  126. Question 126Airframe

    A balance tab on a primary flight control surface helps the pilot by:

    1. indicating the surface's trim position
    2. locking the surface in the neutral position
    3. increasing the surface's travel limits
    4. moving the surface aerodynamically Correct answer.

    Explanation

    A balance tab moves in the opposite direction to the control surface and uses aerodynamic force to help move the surface, reducing pilot effort. It does not lock the surface, limit travel, or indicate trim.

  127. Question 127Airframe

    The function of a circuit breaker in an aircraft electrical circuit is to:

    1. open the circuit on overload Correct answer.
    2. regulate the voltage supplied to the bus
    3. limit radio frequency interference
    4. convert alternating current to direct current

    Explanation

    A circuit breaker opens the circuit when current exceeds its rating, protecting wiring from overheating. It is resettable and does not convert, regulate, or filter.

  128. Question 128Airframe

    Thermal anti-ice systems on turbine engine inlet lips typically use:

    1. pneumatic boots inflated by vacuum
    2. electrical heating elements
    3. engine bleed air Correct answer.
    4. alcohol sprayed onto the surface

    Explanation

    Turbine engine inlet lips are commonly anti-iced with hot compressor bleed air routed through the lip. Electrical elements, alcohol, and pneumatic boots are used in other ice protection designs.

  129. Question 129Airframe

    A bonding jumper installed across a shock-mounted avionics component is used to:

    1. isolate the component from aircraft ground
    2. carry the component's primary operating current
    3. ground the component around the shock mount Correct answer.
    4. damp vibration transmitted to the component

    Explanation

    A bonding jumper provides a low-resistance path around a shock mount so the component remains electrically grounded. The mount isolates vibration, not electrical continuity.

  130. Question 130Airframe

    In a semimonocoque fuselage, the frames are primarily intended to:

    1. carry the primary bending loads along the fuselage
    2. seal the pressurized cabin at each bulkhead
    3. maintain the fuselage shape and support the skin Correct answer.
    4. provide attachment points for the wing spar

    Explanation

    Frames in a semimonocoque fuselage maintain the cross-sectional shape, support the skin and stringers, and carry concentrated loads. Longitudinals such as longerons carry much of the bending load.

  131. Question 131Airframe

    A crack in an aluminum skin is stop-drilled by:

    1. drilling a hole at the center of the crack
    2. drilling a hole at each end of the crack Correct answer.
    3. installing a rivet in the crack tip
    4. grinding the crack flush and applying sealant

    Explanation

    Stop-drilling places a small hole at each end of a crack to remove the sharp tip and reduce stress concentration, helping prevent further propagation. The hole is then inspected and the crack repaired per the manual.

  132. Question 132Airframe

    A composite sandwich panel has a small area of crushed core. The typical repair is to:

    1. fill the crushed area with potting compound only
    2. inject resin into the core and sand smooth
    3. replace the entire panel
    4. splice new core and restore the skins Correct answer.

    Explanation

    Damaged core in a sandwich panel is removed and replaced with new core, and the skins are restored with a bonded or bolted repair. Potting compound alone does not restore structural strength.

  133. Question 133Powerplant

    In a four-stroke-cycle reciprocating engine, the fuel-air mixture is drawn into the cylinder during which stroke?

    1. Compression
    2. Power
    3. Exhaust
    4. Intake Correct answer.

    Explanation

    In the four-stroke cycle the intake valve opens as the piston moves down from top dead center, and the pressure difference draws the charge into the cylinder. Compression, power, and exhaust follow in that order.

  134. Question 134Powerplant

    Which statement correctly defines the compression ratio of a reciprocating engine?

    1. Bore divided by stroke
    2. BDC cylinder volume divided by TDC cylinder volume Correct answer.
    3. Swept volume divided by the number of cylinders
    4. TDC cylinder volume divided by BDC cylinder volume

    Explanation

    Compression ratio compares the total cylinder volume with the piston at bottom dead center to the volume remaining at top dead center. It is a volume ratio, not a dimensional ratio such as bore to stroke.

  135. Question 135Powerplant

    On an engine with solid valve lifters, tappet clearance is measured between the

    1. camshaft lobe and the valve lifter
    2. pushrod and the rocker arm
    3. valve face and the valve seat
    4. rocker arm and the valve stem tip Correct answer.

    Explanation

    Valve lash is the clearance between the rocker arm pad and the tip of the valve stem, or between the valve stem and the tappet. It is set with the lifter on the base circle of the cam and compensates for expansion as the engine warms.

  136. Question 136Powerplant

    Detonation in a reciprocating engine is most likely when

    1. manifold pressure is high, the mixture is lean, and cylinder head temperature is high Correct answer.
    2. the engine is operated at low power with the mixture at full rich
    3. spark advance is retarded from the normal setting
    4. manifold pressure is low, the mixture is rich, and cylinder head temperature is low

    Explanation

    Detonation is the explosive burning of the end gas after normal ignition, promoted by high manifold pressure, lean mixtures, high inlet temperature, and high cylinder head temperature. Reducing power or enriching the mixture removes the conditions that cause it.

  137. Question 137Powerplant

    Preignition is best described as

    1. ignition timed by the magneto to occur at the wrong point in the cycle
    2. ignition of the charge by a hot spot before the spark fires Correct answer.
    3. a second flame front that causes a rapid pressure rise after normal ignition
    4. ignition occurring after the piston passes top dead center

    Explanation

    Preignition means the charge is ignited before the spark plug fires, usually by a glowing hot spot such as a carbon deposit, an overheated electrode, or a cracked exhaust valve. It can destroy a cylinder in seconds and often leads to detonation.

  138. Question 138Powerplant

    Aircraft engine magnetos can produce ignition voltage without an external power source because they use

    1. a permanent magnet that induces current in the primary winding Correct answer.
    2. a transformer that steps up aircraft battery voltage
    3. excitation current supplied by the starter-generator
    4. a battery inside the magneto that is recharged by the engine

    Explanation

    A magneto is a self-contained generator: a rotating permanent magnet induces current in the primary winding, the breaker points interrupt it, and the secondary winding produces the high voltage. No aircraft battery or external excitation is required.

  139. Question 139Powerplant

    Magneto breaker points are timed to open at the E-gap position primarily to

    1. allow the capacitor to discharge through the secondary winding
    2. produce the greatest rate of change of flux through the primary winding Correct answer.
    3. reduce arcing across the points at high engine speed
    4. retard the spark as engine speed increases

    Explanation

    The E-gap is the position slightly past neutral where flux through the primary is changing most rapidly. Opening the points there induces the maximum voltage in the secondary winding, so internal timing is set at that point.

  140. Question 140Powerplant

    Lead fouling on a spark plug is normally removed by

    1. cleaning the plug in an abrasive-type vibrator cleaner Correct answer.
    2. filing the electrodes
    3. soaking the plug in kerosene
    4. re-gapping the electrodes only

    Explanation

    Lead deposits from avgas are removed with an abrasive vibrator-type cleaner, after which the plug is gapped, tested, and inspected. Solvents alone will not remove the fused lead glaze.

  141. Question 141Powerplant

    Which condition is most favorable for carburetor icing?

    1. Air temperature above 90 °F with low relative humidity
    2. Air temperature near freezing with very dry air
    3. Air temperature 30 °F to 50 °F with high relative humidity Correct answer.
    4. Air temperature below 0 °F with low relative humidity

    Explanation

    Impact ice and throttle ice form when moist air is cooled by expansion through the venturi and by fuel vaporization. The most dangerous range is roughly 20 °F to 70 °F with high humidity, so carburetor heat is applied preventively.

  142. Question 142Powerplant

    A primary advantage of an aircraft fuel injection system over a float-type carburetor is that it

    1. operates without an engine-driven air intake
    2. requires no mixture control
    3. delivers a more uniform mixture to each cylinder Correct answer.
    4. eliminates the need for a fuel pump

    Explanation

    Fuel injection meters fuel directly to each cylinder's intake port, so each cylinder receives essentially the same mixture regardless of manifold curvature. It also reduces icing and improves throttle response.

  143. Question 143Powerplant

    In an axial-flow compressor, air is compressed

    1. only in the diffuser behind the last stage
    2. as it passes through rotating and stationary blade rows Correct answer.
    3. by a single centrifugal impeller at the rear
    4. by the turbine section before the combustor

    Explanation

    An axial compressor accelerates air through alternating rows of rotor blades and stationary stator vanes, converting velocity into pressure at each stage. Each stage produces a modest pressure rise, and many stages are stacked in series.

  144. Question 144Powerplant

    Turbine blades in a high-performance engine are commonly cooled by

    1. compressor bleed air through internal passages and film holes Correct answer.
    2. air drawn from the exhaust section and routed through the case
    3. fuel sprayed into the blade root from the fuel nozzle
    4. oil circulated from the lubrication system through drilled passages

    Explanation

    Modern turbine blades are cooled with compressor bleed air that passes through internal passages and exits through film cooling holes, insulating the surface from the gas stream. This lets the blades survive gas temperatures above the metal's melting point.

  145. Question 145Powerplant

    A hung start in a turbine engine is characterized by

    1. light-off with a failure to accelerate to idle Correct answer.
    2. a normal EGT rise with normal acceleration
    3. the starter failing to rotate the engine at any point
    4. acceleration past idle speed after light-off

    Explanation

    A hung start means the engine lights off but stalls below idle because acceleration is insufficient, often from low battery voltage, a weak starter, or incorrect fuel scheduling. The start must be aborted before temperatures exceed limits.

  146. Question 146Powerplant

    Exhaust gas temperature on a turbine engine is used primarily to

    1. measure fuel temperature at the control unit
    2. measure compressor inlet temperature
    3. indicate the temperature of gases leaving the engine and monitor power Correct answer.
    4. indicate oil temperature at the scavenge pump

    Explanation

    EGT reflects the temperature of the gases leaving the engine and is a primary indicator of turbine condition and power output. Pilots use it for leaning and for monitoring takeoff and cruise limits.

  147. Question 147Powerplant

    A hydromechanical fuel control on a turbine engine schedules fuel flow primarily on the basis of

    1. compressor discharge pressure, engine speed, and throttle position Correct answer.
    2. aircraft altitude alone, sensed by an aneroid bellows in the control
    3. oil pressure and oil temperature from the accessory case
    4. exhaust gas temperature alone, taken at the turbine inlet

    Explanation

    A hydromechanical fuel control senses compressor discharge pressure, engine (or compressor) speed, and throttle position, then meters fuel to keep acceleration and steady-state operation within limits. Exhaust gas temperature is a monitored limit rather than the scheduling parameter.

  148. Question 148Powerplant

    In a dry-sump lubrication system, oil is

    1. mixed with the fuel and burned in the cylinders
    2. stored in a separate tank and pressure-fed to the engine Correct answer.
    3. stored in the crankcase sump and circulated by splash
    4. circulated only by the action of the rotating crankshaft

    Explanation

    In a dry-sump system the oil supply lives in a separate tank, and pressure and scavenge pumps move oil to the engine and back to the tank. The crankcase stays relatively dry, which allows the engine to operate in unusual attitudes.

  149. Question 149Powerplant

    Oil dilution in cold weather is used to

    1. thin the oil so the engine can be cranked more easily Correct answer.
    2. increase oil pressure at normal operating temperature
    3. remove contaminants from the oil before starting
    4. raise the flash point of the lubricating oil

    Explanation

    Diluting the oil with a small amount of fuel lowers its viscosity so the engine can be cranked and oil can circulate in cold weather. The fuel evaporates once the oil warms to operating temperature.

  150. Question 150Powerplant

    The oil pressure relief valve in an engine lubrication system

    1. maintains a minimum pressure at idle speed
    2. filters contaminants from the oil before it reaches the bearings
    3. limits maximum pressure by bypassing oil back to the inlet Correct answer.
    4. cools the oil before it enters the engine

    Explanation

    The relief valve protects the system by opening at a set pressure and returning excess oil to the sump or pump inlet. It sets the upper pressure limit rather than maintaining pressure at low speed.

  151. Question 151Powerplant

    A constant-speed propeller maintains a selected RPM by

    1. changing blade pitch as the load on the engine changes Correct answer.
    2. adjusting the turbocharger waste gate
    3. changing engine manifold pressure as load varies
    4. varying the magneto timing with engine speed

    Explanation

    A governor senses engine or propeller RPM and adjusts blade angle through oil pressure. As load changes, pitch changes so the engine holds the RPM selected by the pilot.

  152. Question 152Powerplant

    If engine speed falls below the RPM selected on the propeller governor, the governor will

    1. decrease blade angle to reduce the load on the engine Correct answer.
    2. bypass oil to the return line and hold the present pitch
    3. increase blade angle to slow the engine further
    4. feather the propeller automatically to reduce drag

    Explanation

    When RPM falls below the selected value, the governor admits oil to decrease blade angle, which reduces the load and lets the engine speed back up. Increasing blade angle increases the load and reduces RPM.

  153. Question 153Powerplant

    Dynamic balancing of a propeller assembly corrects

    1. tracking error between the blades
    2. vibration from unbalanced mass in the rotating plane Correct answer.
    3. differences in blade pitch settings
    4. static imbalance only, measured at the blade tips

    Explanation

    Dynamic balancing measures vibration while the propeller rotates and adds or removes weight to correct imbalance in the plane of rotation. Static balancing corrects only the condition in which a blade is heavier when the propeller is at rest.

  154. Question 154Powerplant

    The waste gate on a turbocharged reciprocating engine controls

    1. the oil flow to the turbocharger bearings
    2. the amount of exhaust gas routed to the turbine Correct answer.
    3. the air entering the compressor inlet
    4. the fuel flow to the injector nozzle

    Explanation

    The waste gate is a valve in the exhaust path that bypasses the turbine. Opening it sends exhaust around the turbine to limit boost, while closing it routes more gas through the turbine to increase boost.

  155. Question 155Powerplant

    A thermocouple-type fire detection system works because

    1. a fire lowers the resistance of the sensing loop
    2. a fire raises the pressure of gas inside the sensing tube
    3. a fire heats the junction and generates a small voltage Correct answer.
    4. a fire changes the capacitance of the sensing element

    Explanation

    A thermocouple detector produces a small voltage when its junction is heated by a fire, and the control unit interprets that voltage as a fire warning. Other detector types use resistance, pressure, or gas-absorption changes.

  156. Question 156Powerplant

    Air-cooled engine cylinders are cooled mainly by

    1. conduction of heat through the crankcase
    2. air flowing through fins and directed by baffles Correct answer.
    3. fuel evaporating in the intake port
    4. oil sprayed onto the cylinder barrels

    Explanation

    Fins increase the surface area for heat transfer to the air, and baffles force cooling air to flow close to the fins instead of taking an easy path around the engine. Uneven or blocked airflow produces hot cylinders.

  157. Question 157Powerplant

    Counterweights on a reciprocating engine crankshaft are provided to

    1. offset rotating mass of the throws and reduce bearing loads Correct answer.
    2. dampen torsional vibration at the propeller flange
    3. increase flywheel effect for a smoother idle
    4. balance the reciprocating weight of the pistons and connecting rods

    Explanation

    Crankshaft counterweights offset the centrifugal loads of the rotating crank throws and connecting rod big ends, reducing bending moments and main bearing loads. Reciprocating forces from pistons and rods are a separate balance problem.

  158. Question 158Powerplant

    The performance number of an aviation gasoline, such as 100 in 100LL, indicates the fuel's

    1. resistance to vapor lock
    2. speed of flame travel in the cylinder
    3. ability to lubricate the valves
    4. resistance to detonation Correct answer.

    Explanation

    The grade number of an aviation gasoline is an antiknock rating that describes how much compression pressure the fuel can tolerate before detonating. Higher performance numbers indicate greater resistance to detonation, not greater volatility or lubrication quality.

  159. Question 159Powerplant

    Cowl flaps on an air-cooled engine installation are provided to

    1. control the quantity of cooling air leaving the cowling Correct answer.
    2. reduce aerodynamic drag at high engine power
    3. increase the amount of fuel vaporized in the intake
    4. hold the oil temperature at a fixed value

    Explanation

    Cowl flaps are outlet doors that regulate how much air passes through the cylinder fins and baffles. Opening them increases cooling airflow, and closing them raises cylinder temperatures, so the pilot uses them to keep temperatures within limits.

  160. Question 160Powerplant

    The ignition switch on a reciprocating engine stops the engine by

    1. opening the primary circuit inside the magneto
    2. shorting the secondary winding to ground
    3. grounding the primary circuit to the engine case Correct answer.
    4. removing battery voltage from the magneto coil

    Explanation

    Magnetoes generate their own current, so the switch cannot stop them by removing battery power. Instead the switch connects the primary circuit to ground through the P-lead, which prevents the breaker points from interrupting current and collapses the magnetic field so no spark is produced.

  161. Question 161Powerplant

    The accelerator pump in a float-type carburetor supplies

    1. a temporary enrichment when the throttle is opened quickly Correct answer.
    2. a richer mixture at cruise power
    3. extra fuel for ground idle
    4. fuel for priming before start

    Explanation

    When the throttle is snapped open, airflow increases faster than fuel can flow through the main metering jet, so the mixture momentarily leans. The accelerator pump delivers a measured squirt of fuel to cover that lag and prevent a stumble.

  162. Question 162Powerplant

    Ashless dispersant oil is preferred for most reciprocating aircraft engines because it

    1. forms a hard protective film on parts during storage
    2. raises the antiknock quality of the fuel it contacts
    3. thickens rapidly as oil temperature rises
    4. holds contaminants in suspension so they can be drained or filtered out Correct answer.

    Explanation

    Ashless dispersant oil keeps soot, carbon, and other deposits suspended in the oil rather than letting them settle or stick to engine parts. Because it contains no metallic ash-forming additives, it also leaves no ash deposits when it burns in the combustion chamber.

  163. Question 163Powerplant

    Feathering a propeller places the blades in a position that

    1. allows the propeller to windmill for engine cooling
    2. aligns the blades with the relative airflow Correct answer.
    3. produces maximum thrust at low airspeed
    4. increases blade angle for high-speed cruise

    Explanation

    In feather the blades are rotated to approximately the zero-lift direction so they present the least possible resistance to the airflow. This minimizes drag and prevents windmilling of a failed engine.

  164. Question 164Powerplant

    A carbon dioxide fire extinguisher puts out an engine fire mainly by

    1. coating the fuel with a foam blanket
    2. displacing oxygen in the area of the fire Correct answer.
    3. interrupting the chemical chain reaction
    4. cooling the metal below its ignition temperature

    Explanation

    Carbon dioxide is a nonflammable gas that expands over the fire and reduces the oxygen concentration below the level needed for combustion. It leaves no residue, which makes it suitable for engine and electrical compartments, though it has limited cooling effect.

  165. Question 165Powerplant

    On a twin-spool turbine engine, the N1 indication represents the speed of the

    1. high-pressure compressor and its turbine
    2. low-pressure compressor and its turbine Correct answer.
    3. free power turbine only
    4. accessory gearbox drive shaft

    Explanation

    N1 is the rotational speed of the low-pressure (N1) spool, which consists of the fan or low-pressure compressor and its driving turbine. N2 refers to the high-pressure spool, and the two spools rotate independently on concentric shafts.

  166. Question 166Powerplant

    Which combination of conditions most favors detonation in a reciprocating engine?

    1. High RPM with a rich mixture and open cowl flaps
    2. Low cylinder head temperature and high fuel flow
    3. Low manifold pressure, high RPM, and a rich mixture
    4. High manifold pressure, low RPM, and a lean mixture Correct answer.

    Explanation

    Detonation occurs when the unburned charge ahead of the flame front autoignites from excessive pressure and temperature. High manifold pressure, low RPM, and a lean mixture all raise peak combustion pressure and temperature, which promotes detonation.

  167. Question 167Powerplant

    Valve clearance is built into a reciprocating engine valve train so that the valve

    1. seats fully when the engine is at operating temperature Correct answer.
    2. can rotate freely in its guide
    3. opens earlier as the engine warms up
    4. stays in contact with the rocker throughout the cycle

    Explanation

    Valve train parts expand as the engine reaches operating temperature, so a small clearance is provided when the engine is cold. Without it the expanding parts would hold the valve slightly off its seat, causing compression loss and burned valves.

  168. Question 168Powerplant

    During a differential compression test, air escaping through the exhaust pipe indicates leakage at the

    1. exhaust valve Correct answer.
    2. cylinder head gasket
    3. piston rings
    4. intake valve

    Explanation

    With the piston at top dead center on compression, the intake and exhaust valves should both be closed. Air heard at the exhaust stack is passing the exhaust valve face and seat, which points to a burned or poorly seated exhaust valve.

  169. Question 169Powerplant

    A hot start in a turbine engine is indicated by

    1. an exhaust temperature that exceeds starting limits before idle speed Correct answer.
    2. a rapid acceleration to idle with normal exhaust temperature
    3. a starter that disengages before light-off occurs
    4. an exhaust temperature that stays well below the normal starting range

    Explanation

    A hot start occurs when too much fuel is present at light-off, so combustion temperatures climb rapidly before the engine accelerates. If the exhaust gas temperature approaches or exceeds the starting limit, the start must be aborted to avoid damaging the hot section.

  170. Question 170Powerplant

    A turbine engine compressor stall is typically accompanied by

    1. rising oil pressure with a steady RPM indication
    2. a steady decrease in exhaust temperature with smooth acceleration
    3. silent vibration confined to the accessory section
    4. loud banging, fluctuating RPM, and high exhaust temperature Correct answer.

    Explanation

    A compressor stall occurs when airflow separates from the blades and the compressor can no longer pass air smoothly into the combustor. The result is reverse flow and violent pressure fluctuations, heard as bangs or popping, with unsteady RPM and a rapid rise in exhaust temperature.

  171. Question 171Powerplant

    When engine speed tends to rise above the RPM selected on a constant-speed propeller governor, the governor

    1. opens the waste gate to reduce manifold pressure
    2. increases oil pressure to the prop to raise blade angle Correct answer.
    3. reduces oil pressure to the propeller to decrease blade angle
    4. bleeds governor oil overboard to reduce RPM

    Explanation

    The governor senses the overspeed through its flyweights, which move the pilot valve to direct more oil to the propeller. Higher oil pressure drives the blades toward a higher angle, increasing the load on the engine and bringing RPM back to the selected value.

  172. Question 172Powerplant

    The purpose of an unfeathering accumulator is to

    1. drive the blades out of feather for an air start Correct answer.
    2. hold the propeller in feather after shutdown
    3. dampen rapid changes in engine RPM
    4. prevent the propeller from feathering in flight

    Explanation

    An unfeathering accumulator stores oil under pressure so that, when the propeller control is moved out of feather with the engine not running, oil is available to move the blades to a startable angle. Once the engine starts, the governor takes over normal speed control.

  173. Question 173Powerplant

    On a turbocharged reciprocating engine, the absolute pressure controller limits

    1. manifold pressure by controlling the waste gate Correct answer.
    2. turbine inlet temperature during climb
    3. oil pressure supplied to the turbocharger bearings
    4. turbocharger speed above critical altitude

    Explanation

    The absolute pressure controller senses deck pressure and modulates the waste gate to hold manifold pressure at the selected value as altitude changes. It prevents the turbocharger from overboosting the engine above critical altitude.

  174. Question 174Powerplant

    A continuous-loop fire detection system activates a warning when

    1. a bimetallic switch closes at a preset temperature
    2. a photocell senses infrared radiation from flame
    3. smoke particles bridge a gap between electrodes
    4. heat lowers the resistance of the sensing element Correct answer.

    Explanation

    The sensing element is a wire or tube whose electrical resistance drops as its temperature rises. The control unit monitors that resistance and triggers the warning when it falls to the level that corresponds to a fire.

  175. Question 175Powerplant

    Applying carburetor heat to a running engine normally causes the mixture to

    1. lean out, increasing power
    2. enrich, with a loss of power Correct answer.
    3. remain unchanged in strength
    4. become denser and cooler in the venturi

    Explanation

    Heated air is less dense, so the carburetor meters a richer mixture for the same throttle opening. The warmer, less dense charge also reduces volumetric efficiency, which is why power drops when carburetor heat is applied.

  176. Question 176Powerplant

    The idle cutoff valve on a float-type carburetor is used to

    1. set the mixture for best economy in cruise
    2. prevent backfiring during engine start
    3. bypass the mixture control at full throttle
    4. shut off fuel at the carburetor to stop the engine Correct answer.

    Explanation

    The idle cutoff valve is a pilot-controlled valve that stops fuel flow at the carburetor inlet. Closing it starves the engine so it stops running and, on shutdown, also prevents fuel from continuing to dribble into a hot engine.

  177. Question 177Powerplant

    The blade angle of a propeller is the angle between the

    1. thrust line and the relative wind
    2. chord line and the plane of rotation Correct answer.
    3. plane of rotation and the thrust line
    4. chord line and the hub centerline

    Explanation

    Blade angle is measured between the blade chord line and the plane in which the propeller rotates. It is a fixed geometric property of the blade setting, while the angle of attack depends on the blade angle and the relative wind in flight.

  178. Question 178Powerplant

    An engine operated at high power with a lean mixture shows falling manifold pressure, rising cylinder head temperature, and roughness that persist after the mixture is enriched; these signs are most consistent with

    1. normal operation at best economy mixture
    2. preignition from a local hot spot Correct answer.
    3. an exhaust valve stuck in the open position
    4. ice forming in the induction system

    Explanation

    Detonation generally subsides when the mixture is enriched or power is reduced, so symptoms that continue point to a separate ignition source inside the cylinder. Preignition from an overheated plug, valve, or carbon deposit keeps igniting the charge early and will not stop until the hot spot cools or the power is cut.

  179. Question 179Powerplant

    A full-authority digital engine control (FADEC) on a turbine engine primarily

    1. controls only propeller pitch through the governor
    2. schedules fuel flow and other parameters electronically Correct answer.
    3. monitors engine parameters without commanding any actuator
    4. replaces the ignition system at high altitude

    Explanation

    A FADEC uses digital computers and engine sensors to compute and command fuel flow, bleed valves, variable geometry, and ignition timing within limits. It functions as a full-authority system, meaning it can control the engine without a hydromechanical backup in the normal operating range.

  180. Question 180Powerplant

    A propeller shows excessive tip runout past a fixed reference point and vibrates once per revolution; the first corrective action is to

    1. dynamically balance the propeller
    2. check and correct propeller track Correct answer.
    3. readjust blade angles with a protractor
    4. replace the propeller governor

    Explanation

    Tip runout means the blade tips do not travel in the same plane, which is a track problem caused by a bent blade, a twisted blade shank, or mismatched blade angles. Track should be corrected before balancing, because an out-of-track propeller cannot be balanced meaningfully.

  181. Question 181Powerplant

    Increasing valve overlap in a reciprocating engine generally

    1. reduces cooling of the exhaust valve
    2. improves breathing at high RPM Correct answer.
    3. improves idling smoothness
    4. raises compression pressure at low RPM

    Explanation

    Overlap is the period when both valves are open near top dead center, and the out-flowing exhaust helps draw in the fresh charge. At high RPM the greater gas velocity makes this effect useful, so more overlap improves volumetric efficiency, though it causes poor low-speed and idle behavior.

  182. Question 182Powerplant

    In a radial engine, the master rod differs from the other connecting rods because it

    1. is shorter so that compression stays equal
    2. carries the knuckle pins for the articulating rods Correct answer.
    3. is made of aluminum instead of steel
    4. has no bearing at the crankshaft

    Explanation

    A radial engine has one master rod per row connected directly to the crankshaft, and the remaining link rods attach to knuckle pins on the master rod. All rods therefore act on a single crankpin while still reaching their own pistons.

  183. Question 183Powerplant

    In a high-tension magneto, the high voltage that fires the spark plugs is produced in the

    1. rotating permanent magnet
    2. primary coil winding
    3. secondary coil winding Correct answer.
    4. breaker point assembly

    Explanation

    The primary circuit is interrupted by the breaker points, and the collapsing magnetic field induces a high voltage in the secondary winding, which has many more turns than the primary. The magnet only supplies the magnetic field, and the points only interrupt current.

  184. Question 184Powerplant

    The turbine section of a gas turbine engine extracts energy from the exhaust gases in order to

    1. increase the velocity of the exhaust for thrust
    2. compress the incoming air before combustion
    3. cool the combustion chamber liner
    4. drive the compressor and accessories Correct answer.

    Explanation

    Expanding gases turn the turbine wheel, and the shaft transmits that power forward to the compressor and accessory drives. Any remaining energy in the exhaust produces thrust, but that is not the turbine's job.

  185. Question 185Powerplant

    In a dry-sump reciprocating engine lubrication system, the oil supply is carried

    1. in the hollow crankshaft journals
    2. in a tank mounted outside the engine Correct answer.
    3. in the crankcase sump below the crankshaft
    4. inside the oil cooler core

    Explanation

    A dry-sump system keeps the crankcase relatively dry; scavenge pumps return oil to a separate tank, from which a pressure pump supplies the engine. A wet-sump engine, by contrast, stores oil in the sump.

  186. Question 186Powerplant

    Cylinder head temperature is the most critical temperature to monitor on an air-cooled engine because

    1. it carries the rocker arms
    2. heat concentrates there and at the exhaust valve Correct answer.
    3. it is farthest from the oil supply
    4. it expands more than the barrel

    Explanation

    The cylinder head, particularly around the exhaust valve, absorbs the greatest heat and has the least cooling margin, so head temperature is the limiting factor for engine operation. Barrel temperature is not monitored separately for this reason.

  187. Question 187Powerplant

    The power actually delivered at the propeller shaft of a reciprocating engine is called

    1. indicated horsepower
    2. taxi horsepower
    3. friction horsepower
    4. brake horsepower Correct answer.

    Explanation

    Brake horsepower is the usable output measured at the crankshaft or propeller shaft. Indicated horsepower is the power developed inside the cylinders, and the difference between the two is friction horsepower.

  188. Question 188Powerplant

    A centrifugal compressor raises the pressure of the air passing through it by

    1. adding heat to the air in the diffuser
    2. slowing the air in a diverging duct
    3. squeezing the air between rotating screws
    4. accelerating the air outward and then diffusing it Correct answer.

    Explanation

    The impeller throws air outward at high velocity, and the diffuser converts that velocity into pressure. Pressure rise therefore comes from velocity energy, not from mechanical squeezing or heat addition.

  189. Question 189Powerplant

    When a magneto is timed to an engine, the breaker points should just begin to open

    1. the specified degrees after TDC on compression
    2. at top dead center on the power stroke
    3. the specified degrees before TDC on compression Correct answer.
    4. at top dead center on the exhaust stroke

    Explanation

    Ignition must occur slightly before top dead center on the compression stroke so that peak pressure develops just after TDC. The exact setting is the engine's specified spark advance.

  190. Question 190Powerplant

    In a float-type carburetor, the economizer valve opens at high power settings to

    1. lean the mixture for better economy
    2. enrich the mixture to prevent detonation Correct answer.
    3. cut off fuel flow during shutdown
    4. increase the idle mixture flow

    Explanation

    At high power the economizer adds fuel so the mixture is rich enough to control combustion temperatures and detonation. At cruise the valve stays closed and the mixture is leaner.

  191. Question 191Powerplant

    On many turbine engines, a fuel-oil heat exchanger is used to

    1. warm the fuel and cool the oil Correct answer.
    2. cool the fuel and warm the oil
    3. remove water from the fuel by boiling
    4. raise fuel pressure for the nozzles

    Explanation

    Hot engine oil gives up heat to the colder fuel, which warms the fuel enough to prevent ice crystals from blocking the fuel control while lowering oil temperature. It also helps keep the oil within its viscosity limits.

  192. Question 192Powerplant

    The wastegate on a turbocharged reciprocating engine controls the amount of exhaust gas that

    1. drives the compressor directly
    2. flows through the aftercooler
    3. enters the combustion chamber
    4. bypasses the turbine wheel Correct answer.

    Explanation

    By diverting exhaust around the turbine, the wastegate regulates how fast the turbine and compressor turn and therefore limits manifold pressure. Closing the wastegate sends more gas through the turbine for more boost.

  193. Question 193Powerplant

    An air turbine starter disengages from the engine after start because

    1. the starter clutch is released by oil pressure
    2. a shear section breaks at a set torque
    3. the starter motor reverses direction
    4. an overrunning clutch lets the engine turn faster than the starter Correct answer.

    Explanation

    Once the engine accelerates above starter speed, the overrunning clutch freewheels so the engine cannot drive the starter. This automatic release prevents overspeeding the starter.

  194. Question 194Powerplant

    Cylinder barrels are ground with a slight taper (choke) so that

    1. oil can collect near the top of the barrel
    2. the bore is smallest at the top Correct answer.
    3. the piston can be installed from the top
    4. the rings seat faster during break-in

    Explanation

    The top of the cylinder runs hotter and expands more, so the bore is finished slightly smaller there. When the engine reaches operating temperature the barrel is nearly straight and the rings maintain proper contact.

  195. Question 195Powerplant

    Valve float in a reciprocating engine occurs when

    1. hydraulic lifters bleed down at idle
    2. the springs cannot keep the followers on the cam at high RPM Correct answer.
    3. the camshaft turns faster than the crankshaft
    4. valve clearance closes up as the engine warms

    Explanation

    Above a certain speed the valve spring cannot return the valve and follower quickly enough to follow the cam profile. The valve then bounces on its seat and loses normal timing, which limits maximum RPM.

  196. Question 196Powerplant

    Checking propeller track means checking that

    1. the spinner is centered on the hub
    2. the propeller is balanced statically
    3. the blade tips rotate in the same plane Correct answer.
    4. the blade angles match within tolerance

    Explanation

    Track is checked by turning the propeller and measuring tip runout against a fixed reference. Excessive runout means the tips do not follow the same plane, which produces a once-per-revolution vibration.

  197. Question 197Powerplant

    A hung start in a turbine engine is one in which the engine

    1. fails to light because of a weak igniter
    2. exceeds its normal EGT limit during acceleration
    3. shuts down automatically at starter cutoff
    4. lights and then fails to accelerate to idle speed Correct answer.

    Explanation

    In a hung start the fuel ignites and the engine runs, but it stabilizes below idle speed instead of accelerating. The usual cause is insufficient starting power or fuel scheduling, and the start should be aborted to avoid overheating.

  198. Question 198Powerplant

    At high RPM, a hydraulic valve lifter that pumps up will

    1. open the valve later and close it later
    2. reduce valve lift and shorten duration
    3. hold the valve off its seat and reduce compression Correct answer.
    4. increase valve clearance and cause noise

    Explanation

    Pump-up lengthens the lifter so the valve cannot fully return to its seat, causing loss of compression and possible misfire at high speed. The condition results from the lifter filling faster than it can bleed.

  199. Question 199Powerplant

    Spectrometric oil analysis shows a sharp rise in iron with normal aluminum and copper levels. The most likely source is

    1. aluminum pistons and crankcase
    2. steel parts such as gears and cylinder walls Correct answer.
    3. copper oil cooler tubes and bearings
    4. chromium plating from the rings

    Explanation

    Iron in the sample points to wear of ferrous components such as gears, shafts, cylinder walls, and steel bearing cages. Aluminum and copper readings staying normal help rule out piston, case, and cooler or bearing wear.

  200. Question 200Powerplant

    Interstage bleed valves on an axial-flow compressor are opened at low engine speeds to

    1. cool the compressor case
    2. supply air for cabin pressurization
    3. prevent compressor stall during acceleration Correct answer.
    4. increase the pressure ratio at idle

    Explanation

    At low speed the rear stages cannot handle the airflow the front stages deliver, so bleeding air between stages keeps the front stages from stalling during acceleration. The valves close as speed increases and the stages match.

FAA A&P Mechanic flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Ohm's law
E = I × R, where E is voltage in volts, I is current in amperes, and R is resistance in ohms; electrical power equals E × I.
Moment
A measure of a force's tendency to rotate an object about a point; calculated as weight times arm in inch-pounds and used to compute center of gravity.
Center of gravity
The point at which the entire weight of the aircraft is considered concentrated; found by dividing total moment by total weight and must lie within approved limits.
Annual inspection
A complete inspection required every 12 calendar months, performed by an A&P mechanic holding an Inspection Authorization and recorded in the aircraft maintenance records.
100-hour inspection
Required for aircraft carrying persons for hire or used for flight instruction for hire; performed within the preceding 100 hours of time in service by a certificated A&P.
Galvanic corrosion
Corrosion caused by electrical contact between dissimilar metals in the presence of an electrolyte; prevented by isolating the metals or applying protective coatings.
Magnetic particle inspection
A nondestructive method using magnetic fields and iron particles to reveal surface and near-surface defects in ferromagnetic parts such as steel crankshafts and landing gear components.
Dye penetrant inspection
A nondestructive test using a colored penetrant and developer to reveal surface-breaking defects in nonporous materials such as aluminum and magnesium castings.
Safety wire twist
Properly installed safety wire has six to eight twists per inch and is routed so any loosening tendency pulls the wire in the tightening direction.
Micrometer
A precision measuring instrument with a calibrated screw and thimble that reads to 0.001 inch, used for thickness and diameter measurements.
Torque wrench
A calibrated tool that applies a specified twisting force to a fastener; the reading equals force times arm length in inch-pounds or foot-pounds.
Edge distance rivets
The distance from the center of a rivet to the nearest edge of the sheet, normally at least two rivet diameters to prevent tear-out under load.
Rivet pitch
The spacing between adjacent rivets in a row, typically four to six rivet diameters for single-row joints in aircraft sheet metal repair.
Alclad
Aluminum sheet with a thin layer of pure aluminum rolled onto both surfaces to improve corrosion resistance while the core alloy provides strength.
Accumulator
A hydraulic component containing a compressed gas charge that stores pressure energy, absorbs pressure surges, and supplies flow during peak demand.
Shimmy damper
A device on the nose landing gear that resists rapid side-to-side oscillation of the wheel during ground operation by providing hydraulic damping.
Tensiometer
A calibrated instrument used to measure aircraft control cable tension so the cable can be adjusted to the value specified in the maintenance manual.
Deice boot
An inflatable rubber strip on the leading edge of a wing or tail that expands with air pressure to break ice and allow it to be blown away.
Oleo strut
A landing gear shock absorber using a piston in a cylinder with oil and compressed nitrogen to absorb landing loads and damp rebound.
Bonding jumpers
Low-resistance electrical connections between aircraft structural parts that provide a current return path and drain static electricity safely.
Wing spar
The main structural member of a wing that carries bending and shear loads from the wing skin to the fuselage attachment points.
Aileron differential
Rigging in which the up-going aileron travels farther than the down-going one, reducing adverse yaw and improving coordinated turns.
Four-stroke cycle
The intake, compression, power, and exhaust strokes of a reciprocating engine; two crankshaft revolutions complete one cycle in each cylinder.
Compression ratio
The ratio of total cylinder volume to clearance volume; higher ratios increase power and efficiency but require higher-octane fuel.
Stoichiometric mixture
The chemically correct fuel-to-air ratio of about 15 to 1 by weight, at which all fuel and oxygen are consumed in combustion.
Magneto
A self-contained engine-driven ignition unit that generates high voltage for the spark plugs and operates independently of the aircraft electrical system.
N1
The rotational speed of the low-pressure compressor or fan in a turbine engine, usually expressed as a percentage of a reference RPM.
EGT
Exhaust gas temperature, an indicator of combustion temperature used to set mixture and to monitor turbine engine condition within published limits.
Constant-speed propeller
A propeller whose blade angle is changed by a governor to maintain a selected engine RPM as load and airspeed vary.
Valve clearance
The small gap between the rocker arm and valve stem that allows for thermal expansion and is checked and adjusted during engine inspection.
Ashless dispersant oil
Reciprocating engine oil that keeps contaminants suspended so they drain out with the oil, used in most horizontally opposed aircraft engines.
Carburetor icing
Ice that forms in the carburetor throat from fuel vaporization and pressure drop, most likely at ambient temperatures between 20 and 70 degrees Fahrenheit with high humidity.

FAA A&P Mechanic study guide

General: Fundamentals, Weight & Balance, and the Regulations

What this section actually tests

The General section is the shared-knowledge pool for every mechanic task: basic math and physics (lever arms, mechanical advantage, stress and strain, the difference between work, power, and torque), aircraft drawings and symbols, weight and balance, ground handling and safety, corrosion control, inspection fundamentals and NDI methods, hand tools and precision measuring instruments (micrometer, vernier caliper, torque wrench), fluid lines and fittings, safety wiring, and the rules in 14 CFR Parts 43 and 65.

Weight and balance is the highest-yield topic

Three terms drive every problem: datum (the reference plane), arm (horizontal distance from datum in inches, positive aft), and moment (weight × arm, in pound-inches, usually divided by 1,000 before plotting). Compute empty-weight CG from the equipment list, then add each load at its own arm.

Traps to expect: converting gallons with the wrong density (avgas 6 lb/gal, jet fuel about 6.7, oil about 7.5); forgetting that items forward of the datum give negative arms and negative moments; checking total weight but never checking that the CG falls between the forward and aft limits at that weight; and confusing maximum takeoff weight with maximum landing weight.

Worked example

Empty weight 1,200 lb at +40 in; pilot 170 lb at +37 in; fuel 30 gal at +48 in. Fuel = 30 × 6 = 180 lb. Moments: 48,000 + 6,290 + 8,640 = 62,930 lb-in. Total weight = 1,550 lb. CG = 62,930 ÷ 1,550 = 40.6 in aft of datum. Compare 40.6 to the limit lines at 1,550 lb, not at gross weight.

Regulation bait

Preventive maintenance is limited to the items in Part 43 Appendix A and, for pilots, to aircraft not operated for compensation or hire. A 100-hour inspection applies only to aircraft carrying persons for hire or used for hire for flight instruction; the annual inspection applies to all. Airworthiness Directives are mandatory and must be recorded regardless of use.

Airframe: Structures, Sheet Metal, and Systems

Structures and sheet metal

Every airframe structural question traces back to the five stresses - tension, compression, shear, bending, and torsion - and to the idea that failures start where stress concentrates: cutouts, sharp corners, abrupt thickness changes, and mismatched rivet patterns. Know the difference between a lap joint, a butt joint with a doubler, and a splice; know why a repair must transfer load through the same path as the original structure.

Rivet layout is a reliable question source. FAA guidance calls for a minimum edge distance of about 2 rivet diameters (2D) and a rivet pitch of roughly 3D in a typical repair, with rows staggered and the manufactured head on the outside. Traps: answers given in sixteenths when the stem gives eighths, forgetting that edge distance is measured from the center of the rivet, and using the wrong rivet alloy or head type for the sheet being repaired.

Worked example

A repair uses 1/8-in rivets. Minimum edge distance = 2 × 0.125 = 0.25 in (1/4 in). Typical pitch = 3 × 0.125 = 0.375 in (3/8 in). If a proposed layout shows a rivet 3/16 in from the edge, it fails: 3/16 < 1/4.

Systems and the usual traps

Hydraulics: pressure is set by the system relief valve and is the same throughout a static system, while force = pressure × piston area, so a larger piston area gives more force, not more pressure. Rigging: control cable tension changes with temperature - use the rigging chart and the specified temperature rather than "snug." Corrosion: dissimilar metals plus an electrolyte give galvanic attack; the fix is separation, sealing, and drainage. Fabric, wood, and welding questions usually hinge on inspection access and moisture/rot control rather than obscure technique.

Powerplant: Reciprocating and Turbine Engines

Reciprocating engine fundamentals

Expect questions on the four-stroke cycle (intake, compression, power, exhaust), valve timing and overlap, compression ratio, ignition timing, and the difference between detonation and preignition. Detonation is the rapid, uncontrolled burning of the charge after normal ignition, driven by high manifold pressure, lean mixture, or high CHT. Preignition is ignition of the charge before the spark, usually from a hot spot such as a glowing carbon deposit or overheated plug. Both raise CHT; detonation usually shows a pressure spike and rough running, preignition often shows a rising temperature trend that continues after power reduction.

Fuel metering, induction, and cooling questions usually test cause and effect: carburetor heat richens the mixture and slightly reduces RPM because heated air is less dense; carburetor ice forms most readily at moderate temperatures with high humidity. Magneto questions hinge on the P-lead - a broken P-lead lets the magneto keep firing even with the switch OFF, which is why the grounded-lead check matters before shutdown.

Worked example: torque to horsepower

Brake horsepower = (torque in lb-ft × RPM) ÷ 5,252. An engine producing 300 lb-ft at 2,400 RPM makes (300 × 2,400) ÷ 5,252 = 720,000 ÷ 5,252 ≈ 137 hp. The classic trap is using propeller RPM instead of engine RPM, or forgetting the reduction gear ratio.

Turbines and propellers

Turbine questions focus on the compressor–combustion–turbine sequence, N1 versus N2, and EGT. EGT peaks during start; exceeding the start limit is the classic hot-start damage. Propeller questions test blade angle versus RPM and why a constant-speed propeller needs a governor.

Rule of thumb

If an answer choice fixes a temperature or mixture problem by changing ignition timing, it is almost always wrong - timing does not cure detonation.

FAA A&P Mechanic cheat sheet

Quick reference

General

  • Ohm's law: E = I × R, and power P = E × I. In a series circuit current is constant and voltages add; in a parallel circuit voltage is constant and branch currents add.

  • Weight and balance: moment = weight × arm (inch-pounds); CG = total moment ÷ total weight. The calculated CG must fall within the approved forward and aft limits.

  • Torque = force × perpendicular distance; 1 ft-lb = 12 in-lb. A straight in-line extension does not change the torque applied at the fastener.

  • Aluminum alloys resist corrosion through cladding (Alclad), chemical conversion coatings, or paint; dissimilar metals must be isolated to prevent galvanic corrosion.

  • An annual inspection is due every 12 calendar months and must be signed off by an A&P holding an Inspection Authorization.

  • A 100-hour inspection is required for aircraft carrying persons for hire or used for flight instruction for hire, and may be performed by any certificated A&P.

  • Safety wire is installed so any loosening tendency pulls the wire in the tightening direction; 0.020 to 0.032 inch wire is typical, with 6 to 8 twists per inch.

  • Nondestructive testing selection: magnetic particle for surface and near-surface flaws in ferromagnetic parts; dye penetrant for surface-breaking flaws in nonporous materials; eddy current for conductive materials.

  • A micrometer thimble reads to 0.001 inch; vernier calipers commonly read to 0.001 inch. Measurements are taken at room temperature to avoid thermal error.

Quick reference

Airframe

  • Rivet layout: edge distance is at least 2D from rivet center to sheet edge; pitch is 4D to 6D in a single row and 3D to 4D between rows in multiple-row joints (D = rivet diameter).

  • 2024-T3 aluminum has high strength with fair corrosion resistance; 7075-T6 is stronger but less corrosion resistant; 6061-T6 is weldable and corrosion resistant.

  • Typical transport-category hydraulic system pressure is 3,000 psi; a relief valve limits pressure and an accumulator absorbs surges and supplies flow during peak demand.

  • Control cable tension is measured with a tensiometer and adjusted to the temperature-corrected value in the maintenance manual; surface travel is then checked against rigging tolerances.

  • Pneumatic deice boots on the leading edges inflate at roughly 15 to 20 psi to crack and shed ice; they are checked for proper inflation sequence and leaks.

  • Nose gear shimmy is controlled by a shimmy damper; torque links maintain wheel alignment, and oleo struts use oil plus a nitrogen precharge to absorb landing loads.

  • Fuel tank vents prevent vapor lock and allow the tank to maintain atmospheric pressure; sump drains are sampled for water and sediment before flight.

  • Bonding jumpers provide a low-resistance path between structural components to drain static electricity and complete electrical return circuits.

  • Grade A cotton fabric is finished with dope; approved synthetic covering systems require their specific adhesives, primers, and topcoats per the STC instructions.

Quick reference

Powerplant

  • Four-stroke cycle: intake, compression, power, exhaust. Two crankshaft revolutions (720°) complete one cycle, and valve overlap near top dead center improves volumetric efficiency.

  • Compression ratio = (cylinder displacement + clearance volume) ÷ clearance volume; higher ratios raise power and efficiency but demand higher-octane fuel.

  • Stoichiometric fuel/air ratio is about 15:1 by weight; mixtures richer than stoichiometric (near 12:1) produce best power, while leaner mixtures improve economy.

  • On a four-stroke engine the magneto turns at one-half crankshaft speed and fires each cylinder once per cycle; ignition timing is set before top dead center.

  • Turbine engine monitoring: N1 is low-pressure compressor or fan speed, N2 is high-pressure rotor speed, and EGT or ITT indicates combustion temperature against published limits.

  • Propeller blade angle is measured from the plane of rotation; a constant-speed propeller uses a governor to vary blade angle and hold a selected RPM.

  • Reciprocating engine oil grades are given by viscosity number (100 corresponds to SAE 50); ashless dispersant oil is standard for most horizontally opposed engines.

  • Excessive cylinder head temperature can result from a lean mixture, improper ignition timing, or missing cooling baffles; CHT limits are published in the maintenance manual.

  • Exhaust system cracks or loose connections can leak carbon monoxide into the cabin; exhaust stacks and mufflers are inspected for cracks, erosion, and security.

FAA A&P Mechanic key terms

Airworthiness Directive (AD)

A mandatory FAA rule issued when an unsafe condition is found in a type-certificated product. It specifies required inspections or modifications and must be complied with and recorded before further flight.

Related: Type Certificate, Service Bulletin
Type Certificate

FAA approval of the design of an aircraft, engine, or propeller that meets the applicable airworthiness standards. It establishes the approved configuration against which later alterations and repairs are judged.

Related: Airworthiness Directive (AD), Form 337
Form 337

FAA form used to document a major repair or major alteration and to approve the aircraft for return to service. It identifies the work performed and the approved data relied upon.

Related: Type Certificate, Advisory Circular (AC)
Advisory Circular (AC)

An FAA publication giving nonregulatory guidance, acceptable methods, and procedures for meeting regulations. AC 43.13-1B, for example, describes acceptable methods and practices for aircraft repair.

Related: Form 337
Service Bulletin

A manufacturer's notice recommending inspection, modification, or part replacement on its product. It becomes mandatory only when the FAA issues an Airworthiness Directive requiring compliance.

Related: Airworthiness Directive (AD)
Parts Manufacturer Approval (PMA)

FAA approval for a manufacturer to produce replacement parts for type-certificated products. The holder must show the part is identical to, or a suitable replacement for, the original.

Related: Type Certificate
Torque

A twisting force applied to a fastener, measured in pound-inches or pound-feet. Correct torque stretches the fastener and clamps the joint so it resists vibration and loosening.

Related: Safety Wire
Safety Wire

A locking method in which soft stainless wire is threaded through fastener holes and twisted so any loosening pulls the wire tight. It is installed with the correct pull direction and pigtail.

Related: Torque
Nondestructive Inspection (NDI)

Inspection methods such as dye penetrant, magnetic particle, eddy current, ultrasonic, and radiographic testing that find defects without damaging the part. Selection depends on material and the flaw being sought.

Related: Galvanic Corrosion
Galvanic Corrosion

Corrosion caused by electrical contact between dissimilar metals in the presence of an electrolyte. The less noble metal becomes anodic and wastes away; isolation and protective finishes prevent it.

Related: Alodine (Conversion Coating), Nondestructive Inspection (NDI)
Weight and Balance

The computation confirming that loaded weight and center of gravity fall within approved limits. Out-of-limit loading reduces performance and controllability and can overstress structure.

FAR Part 43

Regulations governing aircraft maintenance, preventive maintenance, rebuilding, and alteration. They define who may perform and approve work and what records must be made.

Related: FAR Part 65, Form 337
FAR Part 65

Regulations for certifying airmen other than flight crew, including mechanics and repairmen. They set experience requirements and the privileges and limitations of a mechanic certificate.

Related: FAR Part 43
Human Factors (Dirty Dozen)

Twelve commonly cited error precursors in maintenance, such as fatigue, complacency, distraction, and poor communication. Recognizing them helps technicians build defenses against mistakes.

Semimonocoque Structure

A stressed-skin structure where the skin carries shear and tension while stringers, frames, and bulkheads stiffen it and carry bending loads. It is the usual construction for modern fuselages and wings.

Related: Stringer, Bulkhead
Stringer

A longitudinal member fastened to the skin that stiffens it and helps carry bending loads. Stringers run spanwise in wings and lengthwise along a fuselage.

Related: Semimonocoque Structure, Rib
Rib

A chordwise member that gives an airfoil its shape and supports the skin and stringers. Ribs transfer aerodynamic loads to the spar.

Related: Spar, Stringer
Spar

The main spanwise beam of a wing or stabilizer that carries bending and shear loads. It is usually built from caps and a web and is a critical inspection item.

Related: Rib
Bulkhead

A transverse structural member that shapes the fuselage and carries concentrated loads from fittings such as wing attachments or landing gear. Pressurized aircraft use bulkheads as pressure boundaries.

Related: Semimonocoque Structure
Empennage

The tail assembly of an aircraft, comprising the horizontal and vertical stabilizers and their control surfaces. It provides stability and pitch and yaw control.

Related: Elevator
Elevator

The hinged control surface on the horizontal stabilizer that controls pitch. Deflecting it changes tail downforce and rotates the aircraft about its lateral axis.

Related: Empennage
Oleo Strut

A landing gear shock absorber that uses compressed gas as a spring and hydraulic fluid forced through an orifice as a damper. It absorbs landing loads and damps rebound.

Hydraulic Accumulator

A pressure vessel holding gas separated from hydraulic fluid by a bladder, diaphragm, or piston. It stores energy for peak demands and smooths pressure surges and pump pulsation.

Outflow Valve

A valve that controls how fast air leaves a pressurized cabin, thereby setting cabin altitude and pressure differential. It works with the pressure controller and cabin safety valves.

Deice Boot

An inflatable rubber strip bonded to a leading edge that expands to crack and shed accumulated ice. Boots are cycled by a pneumatic system when icing conditions are encountered.

Control Cable Tension

The rigging value measured with a tensiometer that keeps a control cable taut without overloading structure. It is set with turnbuckles and corrected for temperature at the time of measurement.

Alodine (Conversion Coating)

A chemical treatment that forms a thin, conductive, corrosion-resistant film on aluminum and improves paint adhesion. It is applied after cleaning and before priming.

Related: Galvanic Corrosion
Four-Stroke Cycle

The intake, compression, power, and exhaust sequence that a reciprocating engine cylinder repeats every two crankshaft revolutions. Each cylinder produces one power stroke per cycle.

Related: Valve Clearance
Magneto

A self-contained, engine-driven ignition unit that generates its own high voltage. Aircraft engines use two independent magnetos for redundancy, and both must be grounded to stop the engine.

Related: Four-Stroke Cycle
Differential Compression Test

A cylinder leakage check in which regulated air is applied at top dead center and the pressure held is compared with the input. Low readings indicate leaking rings, valves, or head gaskets.

Related: Valve Clearance
Wastegate

A valve that routes exhaust gas around the turbine to control boost. It opens to limit manifold pressure and closes as altitude increases to maintain the scheduled power.

Constant-Speed Propeller

A propeller whose blade angle is changed automatically by a governor to hold a selected engine RPM as load varies. This lets the engine run at efficient settings for takeoff and cruise.

Related: Propeller Governor
Propeller Governor

A unit that senses engine speed and meters oil pressure to the propeller hub to change blade angle. Flyweights balanced against a speeder spring hold the selected RPM.

Related: Constant-Speed Propeller
Compressor Stall

A breakdown of airflow through a turbine compressor that causes a bang, power loss, and possible overtemperature. Causes include abrupt throttle movement, foreign object damage, and distorted inlet air.

Related: Exhaust Gas Temperature (EGT)
Exhaust Gas Temperature (EGT)

A turbine engine indication of exhaust gas temperature leaving the engine, used to set power and monitor limits. Abnormally high values warn of overtemperature or hot-section distress.

Related: Compressor Stall
Fuel Control Unit

The unit that meters fuel to a turbine engine according to throttle position, compressor speed, and ambient conditions. It schedules acceleration fuel and protects against overspeed and overtemperature.

Related: Exhaust Gas Temperature (EGT)
Valve Clearance

The gap between the rocker arm and the valve stem that allows for thermal expansion. It is measured with a feeler gauge and set to the manufacturer's cold-engine specification.

Related: Four-Stroke Cycle
Auxiliary Power Unit (APU)

A small turbine engine that supplies electrical power and bleed air, usually on the ground. It has its own starting, fuel, oil, and control systems and is not used for propulsion.

FAA A&P Mechanic study plan

8 weeks · About 6 hours per week

Week 1

Powerplant

  • Describe the four-stroke reciprocating engine cycle and identify the components that carry out each stroke

  • Differentiate between horizontally opposed, radial, and inline engine configurations by cylinder arrangement and firing order

  • Explain the purpose and inspection points of the lubrication system, including oil pumps, coolers, and filters

  • Identify the maintenance record entries and inspection requirements triggered by an engine oil system component replacement

Your checkpoint

Draw and label a complete reciprocating engine lubrication system diagram from memory, then grade it against your own notes to reach at least 90% of labeled components correct

Week 2

Powerplant

  • Trace the induction and exhaust airflow path on both carbureted and fuel-injected reciprocating engines

  • Compute fuel-air mixture ratios and explain how carburetor ice forms under varying temperature and humidity conditions

  • Explain cooling system airflow and cylinder head temperature control, including cowl flap function

  • Describe magneto operation and the sequence of events in an ignition system check

Your checkpoint

Write a 12-question self-quiz on induction, exhaust, cooling, and ignition, answer it closed-book, and score at least 10 of 12 before moving on

Week 3

Powerplant

  • Differentiate turbojet, turbofan, and turboprop engines by airflow path and thrust production method

  • Identify turbine engine hot section components and the inspection criteria used to judge their condition

  • Explain propeller blade angle, pitch, and the operational difference between fixed-pitch and constant-speed propellers

  • Describe starting system and engine electrical component functions on both reciprocating and turbine installations

Your checkpoint

Produce a two-column comparison sheet covering turbine versus reciprocating engine systems in at least 8 categories, each with a one-sentence operational difference you can explain aloud without notes

Week 4

Powerplant & General

  • Summarize the powerplant knowledge areas you have covered so far into a single reference outline

  • Explain the privileges and limitations of a mechanic certificate with airframe and powerplant ratings

  • Identify the maintenance record entries required after an engine component is replaced

  • Solve powerplant calculation problems involving fuel consumption, horsepower, and engine displacement

Your checkpoint

Complete a timed 50-question powerplant practice set and score at least 80%, logging every missed item with the reason for the error

Week 5

General

  • Solve weight and balance problems for aircraft with and without alterations, computing empty weight, arm, and center of gravity

  • Apply basic physics and math principles to mechanical advantage, stress, and fluid pressure problems

  • Interpret aircraft drawings, including lines, symbols, and dimensioning conventions

  • Identify corrosion types and match each to an inspection and treatment method

Your checkpoint

Complete a weight and balance worksheet with 5 solved problems showing all steps, plus a corrosion identification table covering at least 6 corrosion types

Week 6

General & Airframe

  • Describe aircraft ground handling and safety procedures, including jacking, tie-down, and fueling precautions

  • Explain materials and processes topics, including heat treatment, nondestructive inspection methods, and hardware selection

  • Summarize basic electrical theory as applied to aircraft circuits, including Ohm's law calculations and wire sizing

  • Identify sheet metal structural repair principles and rivet layout requirements

Your checkpoint

Build a one-page quick-reference sheet of formulas and rules of thumb for weight and balance, Ohm's law, and sheet metal rivet spacing, then use it to answer 15 mixed General questions with at least 12 correct

Week 7

Airframe

  • Trace hydraulic and pneumatic system flow from reservoir through pumps, valves, and actuators

  • Explain landing gear operation, including retraction systems, steering, brakes, and warning indicators

  • Diagnose common airframe electrical and rigging faults by matching symptoms to likely causes

  • Describe aircraft finish and covering inspection criteria, including fabric and composite condition assessment

Your checkpoint

Create a symptom-to-cause diagnostic table with at least 10 airframe system faults and verify each entry against your study notes, correcting any entry you cannot justify

Week 8

Airframe & General & Powerplant

  • Reconcile all missed practice questions from weeks 4 through 7 and restate the correcting principle for each

  • Complete full-length timed practice sets for Airframe, General, and Powerplant in that order of emphasis

  • Recite inspection and documentation requirements that apply across all three knowledge areas

  • Identify remaining weak areas and create a final-week targeted review list of no more than 10 items

Your checkpoint

Score at least 85% on a full-length practice set for each of the three knowledge areas and submit a written list of remaining weak items with a stated review action for each

Milestones

Week 2: Closed-book powerplant systems quiz scored at 10 of 12 or better; any missed item restated correctly in writing

Week 4: Timed 50-question powerplant practice set scored at 80% or higher with an error log completed

Week 6: Mixed General and Airframe question set scored at 80% or higher, and the one-page formula reference sheet completed

Week 8: Full-length practice sets for all three knowledge areas each scored at 85% or higher, with a final weak-item action list written

FAA A&P Mechanic exam day

Your checklist

Unexpired government-issued photo ID

Bring a driver's license, passport, or military ID. The name on the ID must match the name on your application and knowledge test reports. Confirm acceptable ID forms with your examiner before test day.

FAA knowledge test reports (General, Airframe, Powerplant)

Bring the printed, embossed knowledge test reports for each rating you are testing. Results generally must be within their validity window (commonly stated as 24 months for mechanic applicants) - confirm the exact currency rule and any exceptions with your examiner or the local FSDO.

FAA Form 8610-2, completed and signed

Airman Certificate and/or Rating Application with the experience certification completed by the authorized person who verified your experience. Confirm signature requirements and whether the examiner or FSDO signs it in your case.

Experience records and logbook

Bring documentation of the required practical experience (commonly 18 months for a single rating, 30 months for both Airframe and Powerplant). Highlight entries that support the tasks you may be asked to perform.

Basic hand tools

Most examiners expect you to work with your own tools. Typical items include combination wrenches and sockets, screwdrivers, pliers, safety wire pliers and wire, torque wrench, inspection mirror, flashlight, and a multimeter. Confirm the exact tool list with your examiner (needs_review - requirements vary by examiner and test site).

Personal safety equipment

Safety glasses, hearing protection, work gloves, and closed-toe, non-slip shoes. Some tasks involve running engines, electrical work, or chemicals where PPE is expected.

Work clothing

Coveralls or shop-appropriate clothing you can move and bend in; secure long hair and remove jewelry, rings, and loose sleeves that could create a hazard around rotating or electrical equipment.

Approved reference materials

Bring the FAA handbooks (General, Airframe, Powerplant) and AC 43.13-1B/2B if permitted. Ask what references, tabbing, and notes are allowed; some examiners restrict pre-tabbed or annotated material (needs_review - confirm with your examiner).

Appointment confirmation and site logistics

Confirm date, time, address, entry procedure, and parking with the examiner's office a few days ahead. Save the examiner's phone number in case of travel delay.

Examiner fee and payment method

Examiner fees are separate from FAA fees. Confirm the amount, accepted payment method, and whether payment is due before or after the test (needs_review - fees and methods vary by examiner).

Small personal items

Pencil/pen, notepad, basic calculator (if approved), water, snack, and any personal medication. Plan bathroom and meal breaks into your arrival schedule.

Accommodation request, if needed

If you need testing accommodations, request them well in advance and in writing. Approval is not guaranteed on test day (needs_review - confirm the process with the examiner or FAA).

Phone and smartwatch plan

Plan to silence or stow devices before entering the testing area. Confirm the examiner's device policy in advance so you are not caught off guard.

Plan the day

72 hours before

Reconfirm the appointment, site, fee, and required documents with the examiner. Verify your knowledge test reports are still valid and that your 8610-2 is properly completed and signed. Finalize your tool inventory against the examiner's list.

72 hours before

Shift from reading to doing: practice high-risk practical tasks - safety wiring, torque wrench use, rigging checks, logbook entries, AD and airworthiness-directive research, weight and balance, and pre-oil/run-up procedures. Rehearse talking through what you are doing and why, since the oral and practical portions are commonly integrated.

24 hours before

Pack your tools and bag from the checklist, lay out ID and paperwork in one folder, and load the vehicle or confirm travel arrangements. Check weather and traffic for the route. Eat a normal meal, set two alarms, and get a full night's sleep instead of last-minute cramming.

24 hours before

Do a light review of the practical test standards task list and the reference material you plan to use in front of the examiner. Stop studying early enough to sleep.

Morning of

Eat breakfast and hydrate. Arrive 30–45 minutes early to park, check in, and settle. Keep your ID, knowledge test reports, and 8610-2 in hand. Turn your phone off or stow it as directed.

Start of test

Listen to the examiner's briefing on the test sequence, time expectations, break policy, and what reference material is permitted. Ask questions about the process now, before tasks begin.

During the test

Read or listen to each task carefully, ask for clarification if instructions are ambiguous, and state your safety precautions before starting. Use the approved references when unsure rather than guessing. Work steadily, and clean up and account for tools after each task.

End of test

Ask for a debrief on how each area went, confirm what paperwork is completed and submitted, and get clear instructions on next steps if any task needs re-examination.

Rules to check

  • Present a valid, unexpired government photo ID at check-in; the name must match your application and test records. Confirm acceptable ID with the examiner beforehand.

  • Perform only the tasks the examiner assigns, in the order and manner directed. Do not substitute your own preferred procedure for the one the task specifies.

  • Ask for clarification when a task instruction is unclear - asking is not a failure, but proceeding on a guess can be.

  • Treat safety as non-negotiable: unsafe acts, bypassing lockout or PPE requirements, or damage to equipment may result in disapproval of the affected task or the test. Confirm the examiner's specific safety criteria at the start.

  • Reference materials, calculators, and notes may be restricted. Confirm in advance what you may bring into the testing area and keep unapproved items stowed.

  • Breaks are typically available on request, and the examiner controls the schedule and any time expectations. Ask about the break policy during the opening briefing.

  • Phones, smartwatches, and recording devices are generally not permitted in the testing area, and exam content is confidential. Do not discuss specific tasks or questions afterward in a way that compromises test security.

  • If a task is not satisfactorily completed, re-examination is usually required on that area. The retest process, eligibility, and any waiting period are set by the FAA and the examiner - confirm the exact policy with your examiner or the local FSDO rather than relying on rumor.

FAA A&P Mechanic FAQ

How many FAA A&P Mechanic practice questions are available?

The practice set has 200 FAA A&P Mechanic questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many FAA A&P Mechanic flashcards are available?

The flashcard set has 32 FAA A&P Mechanic cards. Each card shows the term and its definition.

Which topics does the FAA A&P Mechanic study material cover?

The FAA A&P Mechanic study material covers General: Fundamentals, Weight & Balance, and the Regulations, Airframe: Structures, Sheet Metal, and Systems, and Powerplant: Reciprocating and Turbine Engines.

What format facts does the catalog list for the FAA A&P Mechanic exam?

The catalog lists these item types: multiple choice for the FAA A&P Mechanic exam.