CCNA (200-301) Practice Test

Cisco Certified Network Associate (CCNA 200-301)

CCNA overview

  • 200 practice questions
  • 32 flashcards
  • 6 study guide topics
  • 36 key terms

What you'll study

  • Network Fundamentals20%
  • Network Access20%
  • IP Connectivity25%
  • IP Services10%
  • Security Fundamentals15%
  • Automation and Programmability10%

The Cisco Certified Network Associate (CCNA) is Cisco's associate-level networking certification and the usual entry point into Cisco's certification path. It suits people who want proof of practical, day-to-day networking skill rather than product-specific depth: helpdesk and NOC staff moving into network roles, career changers coming out of a networking course, and junior engineers who already touch routers and switches and want a structured, vendor-recognized credential to show for it.

The blueprint is organized into six areas - network fundamentals, network access, IP connectivity, IP services, security fundamentals, and automation and programmability - and it rewards configuration and verification knowledge over trivia. Expect to read a topology, predict how traffic flows, and explain why a given configuration does or does not work.

Preparation usually combines a structured course with hands-on repetition. Cisco's own learning paths include Cisco U., Cisco Networking Academy, instructor-led training, Cisco Packet Tracer, and Cisco Modeling Labs. Whatever the source, plan to build labs, break them, and fix them - reading alone rarely gets a candidate across the line.

Exam logistics - cost, length, item count, and passing score - are set by Cisco and change with blueprint revisions; verify them on Cisco's official CCNA page before you schedule.

Common mistakes

Subnetting by writing out binary for every question instead of using the block-size (magic number) shortcut, which burns 3-5 minutes per question and leaves the simulation/lab items at the end of the exam unreached.

Most candidates learn binary conversion first and never drill the 256-minus-mask-mask-octet method, so every subnet question becomes long division in base 2 under a clock.

What to do instead

Drill the shortcut daily: mask octet -> block size -> valid subnets -> broadcast. Target under 20 seconds for any /17 through /30 question. Practice on 10 random 'given 192.168.44.0/27, list the third subnet, its range, and broadcast' prompts and time yourself.

Classifying a fault to the wrong OSI layer: labeling a VLAN mismatch or native-VLAN mismatch as a Layer 1 problem, placing ARP at Layer 2 only, or saying a switch 'routes' frames.

Layers get memorized as a list of seven names and one keyword each, not as an encapsulation model, so symptoms that straddle layers (MTU, duplex mismatch, VLAN tagging, ARP) have no anchor.

What to do instead

For each layer write the PDU name, the addressing used, the device that acts there, and two real symptoms. Then take 20 trouble tickets and force yourself to name the layer plus one command that would prove it (show interfaces, show mac address-table, show arp, show ip route).

Troubleshooting a trunk that 'isn't passing VLANs' by only re-typing 'switchport mode trunk', without comparing the allowed VLAN list, the native VLAN on both ends, and whether DTP negotiated the link as access.

Practice labs use default trunks between directly connected switches, so allowed-list and native-VLAN mismatches never appear until the exam presents a partially configured topology.

What to do instead

Build a fixed trunk checklist you run every time: show interfaces trunk (mode, encapsulation, native VLAN, allowed and active VLANs), show interfaces switchport on both ends, and compare native VLANs. Configure 'switchport nonegotiate' with an explicit 'switchport trunk allowed vlan' in labs so you see the failure modes.

Configuring OSPF and moving on without checking adjacency, so the router has no routes but the config 'looks right'; also writing 'network 10.0.0.0 255.255.255.0 area 0' as if it were a subnet mask.

OSPF takes the config silently - a hello/dead timer, area ID, MTU, stub flag, or authentication mismatch just leaves neighbors stuck in INIT/EXSTART with no error message, and the network statement wildcard mask is easy to type as a normal mask.

What to do instead

Make 'show ip ospf neighbor' mandatory after every OSPF change and require FULL/DR or FULL/BDR before continuing. Drill wildcard conversion (255.255.255.255 minus the mask) and memorize the default hello/dead timers for broadcast (10/40) and non-broadcast (30/120).

Picking a route by lowest metric or by 'most specific-looking' instead of applying longest prefix match first, then administrative distance, then metric.

Study material teaches AD and metric as separate facts, so candidates default to whichever number is smaller across routes learned from different sources.

What to do instead

Recite the order out loud every time: longest prefix match wins outright; only among equal prefixes compare AD; only among equal prefix and equal AD compare metric. Work 10 sets of five competing routes and write the elimination reason next to each losing route.

Placing a DHCP server on a different subnet from the clients and never configuring 'ip helper-address' on the client-facing router interface, then blaming the DHCP pool.

Nearly every practice lab puts the DHCP server on the same LAN, so broadcast containment by the router never becomes visible as a failure.

What to do instead

Lab it deliberately: one router, two LANs, DHCP server on LAN B, clients on LAN A. Confirm clients fail, add ip helper-address pointing at the server, and verify with 'show ip dhcp binding' and 'show ip dhcp conflict'. Note that the helper forwards to UDP 67 using the interface address as source.

Building a static NAT or PAT config that looks complete but never marks the interfaces 'ip nat inside' / 'ip nat outside', and never verifies with 'show ip nat translations' or 'debug ip nat'.

NAT syntax is order-dependent and a missing interface designation produces zero errors - packets simply aren't translated, which reads as a routing problem.

What to do instead

Use a fixed four-step build order and check it each time: (1) mark inside/outside interfaces, (2) define the match ACL or 'nat inside source list/interface overload', (3) apply to the correct interface and direction, (4) verify with show ip nat translations, show ip nat statistics, and clear ip nat translation * before retesting.

Treating the three port-security violation modes as interchangeable, and forgetting that a shutdown violation err-disables the port with no automatic recovery.

The mode names are memorized as a list without the behavior table, so protect/restrict/shutdown get swapped under pressure, and errdisable recovery timers are assumed to be on by default when they are off.

What to do instead

Write the three-column table once - protect (drops, no log, no counter increment), restrict (drops, logs, increments violation counter), shutdown (err-disables, logs, counter) - and lab each mode with 'show port-security interface'. Then add 'errdisable recovery cause psecure-violation' and verify with 'show errdisable recovery'.

Assuming Ansible requires an agent on managed devices, or swapping YANG for NETCONF/RESTCONF as if they were the same thing, and describing the controller as forwarding traffic.

The automation domain is often skimmed because it 'isn't networking', so the tool/protocol/model layers blur into undifferentiated buzzwords.

What to do instead

Build a one-page matrix with rows for Ansible, Puppet, Chef, and columns for agent vs agentless, push vs pull, language, and transport. Separately define the stack: YANG = the data model, NETCONF/RESTCONF = the transport/protocol carrying it, SNMP = legacy monitoring. State clearly that the controller manages the control plane and does not forward data-plane traffic.

Memorizing controller names (DNA Center, APIC, WLC) without being able to say which plane each acts on or what a northbound versus southbound API is used for.

SDN questions are answered by name recognition rather than by the control-plane/data-plane split, so any question phrased around APIs or flows breaks the pattern.

What to do instead

For each controller write: what it manages, whether it is on-prem or cloud, the interface it uses southbound to devices (CLI/SNMP/NETCONF), and the northbound interface it offers to applications (REST API). Practice explaining in two sentences how a centralized control plane differs from a distributed one on traditional routers.

Exam requirements can change. Confirm current details with the exam provider.

CCNA practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Network Fundamentals

    A router forwards packets between different IP networks. At which OSI model layer does this forwarding decision primarily occur?

    1. Layer 1 – Physical
    2. Layer 2 – Data link
    3. Layer 4 – Transport
    4. Layer 3 – Network Correct answer.

    Explanation

    Routers choose an outbound interface by comparing the packet's destination logical address against a routing table, and logical addressing is defined at Layer 3. Layer 2 forwarding uses hardware addresses and stays inside a single broadcast domain. A Layer 3 switch performs the same lookup only when routing is enabled.

  2. Question 2Network Fundamentals

    Which protocol data unit (PDU) is created at the transport layer of the OSI model?

    1. Segment Correct answer.
    2. Frame
    3. Bit
    4. Packet

    Explanation

    The transport layer encapsulates application data into segments (TCP) or datagrams (UDP) and adds port numbers. Each lower layer renames the PDU as it adds its own header, so naming follows the layer that built it.

  3. Question 3Network Fundamentals

    How many bits long is a MAC address?

    1. 32 bits
    2. 128 bits
    3. 48 bits Correct answer.
    4. 64 bits

    Explanation

    MAC addresses are 48 bits, usually written as 12 hexadecimal digits. The first 24 bits identify the manufacturer (OUI) and the last 24 bits are assigned by that vendor. This size keeps addresses globally unique while fitting in a small frame header.

  4. Question 4Network Fundamentals

    Which TCP port is used by HTTPS by default?

    1. 443 Correct answer.
    2. 25
    3. 80
    4. 21

    Explanation

    HTTPS runs HTTP inside TLS and listens on TCP 443 by default, while plain HTTP uses TCP 80. Well-known ports below 1024 are assigned by IANA so clients know where to connect without being told.

  5. Question 5Network Fundamentals

    What is the maximum standard cable length for an Ethernet run over unshielded twisted-pair copper?

    1. 185 m
    2. 100 m Correct answer.
    3. 55 m
    4. 500 m

    Explanation

    Structured cabling standards limit a horizontal UTP channel to 100 m: up to 90 m of permanent cable plus 10 m of patch cords. Longer runs exceed the channel budget and cause signal attenuation and test failures.

  6. Question 6Network Fundamentals

    Which of these IPv4 addresses is a private address as defined by RFC 1918?

    1. 11.5.5.10
    2. 172.32.5.10
    3. 172.20.5.10 Correct answer.
    4. 192.169.5.10

    Explanation

    RFC 1918 reserves 10.0.0.0/8, 172.16.0.0/12 (172.16.0.0 through 172.31.255.255), and 192.168.0.0/16 for private use. Addresses in those ranges are not routed on the public Internet and normally require NAT to reach it.

  7. Question 7Network Fundamentals

    A host that cannot reach a DHCP server may assign itself an address from which range?

    1. 169.254.0.0/16 Correct answer.
    2. 10.0.0.0/8
    3. 192.168.0.0/16
    4. 127.0.0.0/8

    Explanation

    When DHCP fails, many operating systems fall back to link-local self-assignment using the 169.254.0.0/16 range, often called APIPA. The host verifies the address is unused with an ARP probe before using it. Such hosts can talk to other link-local hosts on the same segment but have no default gateway.

  8. Question 8Network Fundamentals

    What is the primary function of DNS?

    1. Map IP addresses to hardware addresses
    2. Encrypt traffic between clients and servers
    3. Resolve host names to IP addresses Correct answer.
    4. Assign IP addresses to hosts dynamically

    Explanation

    DNS is a distributed database that translates human-readable names, such as www.example.com, into the IP addresses that hosts actually use for delivery. Clients query a configured resolver, which walks or caches the hierarchy of name servers.

  9. Question 9Network Fundamentals

    A host must send a frame to another host on the same subnet but knows only the destination IPv4 address. How does it learn the destination MAC address?

    1. By sending an ARP request Correct answer.
    2. By sending a DNS query
    3. By sending a DHCP request
    4. By sending an ICMP echo request

    Explanation

    ARP broadcasts a request asking which device owns the target IPv4 address, and the owner replies unicast with its MAC address. The result is cached for a short time so later frames can be sent directly. This process only occurs for destinations the sender considers local.

  10. Question 10Network Fundamentals

    How many usable host addresses are available in a /27 IPv4 subnet?

    1. 14
    2. 32
    3. 62
    4. 30 Correct answer.

    Explanation

    A /27 borrows 27 network bits, leaving 5 host bits, so the subnet holds 2^5 = 32 addresses. Two of those are reserved for the network and broadcast addresses, leaving 30 assignable to hosts.

  11. Question 11Network Fundamentals

    What is the broadcast address of the subnet 172.16.4.64/26?

    1. 172.16.4.128
    2. 172.16.4.63
    3. 172.16.4.127 Correct answer.
    4. 172.16.4.191

    Explanation

    A /26 leaves 6 host bits, so each subnet contains 64 addresses and the subnets start at .0, .64, .128, and .192. The subnet beginning at .64 spans .64 through .127, making .127 the highest address and therefore the broadcast.

  12. Question 12Network Fundamentals

    A 24-port switch has a device connected to every port, and all ports are members of the same VLAN. How many collision domains exist?

    1. 2
    2. 12
    3. 1
    4. 24 Correct answer.

    Explanation

    Each switch port is its own collision domain because the switch buffers and forwards frames per port instead of repeating signals to all ports. All 24 ports remain in a single broadcast domain because they share one VLAN.

  13. Question 13Network Fundamentals

    Which IPv6 address type is automatically configured on an enabled interface and always begins with fe80::/10?

    1. Global unicast
    2. Multicast
    3. Link-local Correct answer.
    4. Unique local

    Explanation

    Every IPv6-enabled interface forms a link-local address from the fe80::/10 prefix, either from the MAC address or a randomized value. Link-local addresses are used for neighbor discovery and next-hop resolution and are never routed off the link.

  14. Question 14Network Fundamentals

    Which Ethernet frame field lets a receiving device detect a corrupted frame?

    1. Start frame delimiter
    2. Preamble
    3. Frame check sequence Correct answer.
    4. Type/length

    Explanation

    The frame check sequence is a CRC value calculated over the frame contents and placed in the trailer. The receiver recalculates the CRC and discards the frame if the values differ, which is why many corruption problems show up as dropped frames rather than errors at upper layers.

  15. Question 15Network Fundamentals

    Which set of flags describes the TCP three-way handshake in the order the packets are sent?

    1. ACK, SYN, ACK
    2. SYN, SYN-ACK, ACK Correct answer.
    3. SYN, ACK, SYN-ACK
    4. SYN, FIN, ACK

    Explanation

    The initiator sends a SYN with its initial sequence number, the responder replies with SYN and ACK acknowledging that number while offering its own, and the initiator finishes with an ACK. Both sides now have synchronized sequence numbers and can exchange data reliably.

  16. Question 16Network Fundamentals

    Which statement describes UDP?

    1. It performs a three-way handshake before data transfer
    2. It is connectionless and adds little overhead Correct answer.
    3. It guarantees in-order delivery of data
    4. It retransmits lost segments

    Explanation

    UDP sends datagrams without establishing a session, acknowledging receipt, or resequencing, so its header is only 8 bytes. Applications that prefer speed or handle recovery themselves, such as DNS, DHCP, and voice, use UDP.

  17. Question 17Network Fundamentals

    On a link where both endpoints are configured for full duplex, which function is not required?

    1. Preamble generation
    2. Framing
    3. CSMA/CD Correct answer.
    4. Error detection

    Explanation

    Full duplex uses separate transmit and receive wire pairs, so a station can send and receive simultaneously and collisions cannot occur. Collision detection and the associated backoff algorithm exist only for shared half-duplex media.

  18. Question 18Network Fundamentals

    Which group of channels in the 2.4 GHz band is non-overlapping?

    1. 1, 6, 11 Correct answer.
    2. 3, 8, 13
    3. 1, 5, 9
    4. 2, 7, 12

    Explanation

    2.4 GHz channels are spaced 5 MHz apart but each channel is about 22 MHz wide, so adjacent channels overlap. Choosing channels five apart, such as 1, 6, and 11, separates the center frequencies enough to avoid co-channel interference in the common regulatory domain.

  19. Question 19Network Fundamentals

    Which IEEE standard defines PoE that delivers up to about 15.4 W to a powered device?

    1. 802.3af Correct answer.
    2. 802.3at
    3. 802.3ad
    4. 802.11ac

    Explanation

    802.3af, commonly called PoE, provides roughly 15.4 W at the powered device over the same cable that carries data. 802.3at, or PoE+, raises that to about 25.5 W for devices such as access points and pan-tilt-zoom cameras.

  20. Question 20Network Fundamentals

    In which cloud service model does the provider manage the operating system, runtime, and middleware while the customer deploys only applications?

    1. PaaS Correct answer.
    2. On-premises
    3. SaaS
    4. IaaS

    Explanation

    Platform as a service supplies a managed runtime and supporting services so developers can push code without patching servers or installing middleware. In IaaS the customer still manages the guest OS, and in SaaS the customer simply consumes a finished application.

  21. Question 21Network Fundamentals

    An engineer must divide 192.168.10.0/24 into subnets that each support at least 25 hosts, using the longest prefix that still meets the requirement. Which prefix should be chosen?

    1. /27 Correct answer.
    2. /25
    3. /26
    4. /28

    Explanation

    A /27 leaves 5 host bits, giving 32 addresses and 30 usable hosts, which satisfies the 25-host requirement while creating 8 subnets. A /28 would yield only 14 usable hosts and therefore fail, so /27 is the longest prefix that still works.

  22. Question 22Network Fundamentals

    Which is a correctly compressed form of 2001:0db8:0000:0000:0000:0000:0000:0001?

    1. 2001:db8::1 Correct answer.
    2. 2001:db8::1::
    3. 2001:db8::1:0:0
    4. 2001:0db8:0:0:0:0:1

    Explanation

    Compression removes leading zeros in each group and replaces one contiguous run of all-zero groups with a double colon. Here that leaves 2001, db8, then the zero run, then 1, giving 2001:db8::1. The double colon may appear only once in an address.

  23. Question 23Network Fundamentals

    Which address is a valid host address on the subnet 10.1.1.0/30?

    1. 10.1.1.4
    2. 10.1.1.3
    3. 10.1.1.0
    4. 10.1.1.2 Correct answer.

    Explanation

    A /30 leaves 2 host bits, so the block covers four addresses: 10.1.1.0 through 10.1.1.3. The first address is the network ID and the last is the broadcast, leaving .1 and .2 as the only usable host addresses.

  24. Question 24Network Fundamentals

    A 255.255.255.224 mask is applied to 192.168.5.0. Which address belongs to the third subnet?

    1. 192.168.5.62
    2. 192.168.5.96
    3. 192.168.5.33
    4. 192.168.5.70 Correct answer.

    Explanation

    The mask 255.255.255.224 is a /27, so the block size is 32 and subnets begin at .0, .32, and .64. The third subnet spans 192.168.5.64 through 192.168.5.95, so .70 is a host inside it.

  25. Question 25Network Fundamentals

    Host A (192.168.1.10/24) sends a packet to 192.168.2.20 and uses default gateway 192.168.1.1. Which destination MAC address does the frame carry when it leaves Host A?

    1. The MAC address of 192.168.2.20
    2. The broadcast address FF:FF:FF:FF:FF:FF
    3. The MAC address of the default gateway Correct answer.
    4. The MAC address of Host A

    Explanation

    Host A compares the destination with its own mask, sees that 192.168.2.20 is on a different network, and forwards the frame to its default gateway. The frame's destination MAC is therefore the router interface's address, while the destination IP stays set to 192.168.2.20 for the whole trip.

  26. Question 26Network Fundamentals

    Which device primarily makes forwarding decisions based on destination MAC addresses?

    1. A firewall
    2. A Layer 2 switch Correct answer.
    3. A repeater hub
    4. A Layer 3 router

    Explanation

    A switch learns source MAC addresses and forwards frames based on the destination MAC address in its MAC address table. Routers forward using IP addresses, hubs simply repeat signals, and firewalls filter traffic by policy.

  27. Question 27Network Fundamentals

    What does a host use a default gateway for?

    1. To translate domain names into IP addresses
    2. To detect duplicate addresses on the link
    3. To assign an IP address automatically
    4. To forward traffic to another subnet Correct answer.

    Explanation

    A default gateway is a router interface on the host's local subnet. The host sends traffic destined for other subnets to that gateway for routing.

  28. Question 28Network Fundamentals

    What is the purpose of the TTL field in an IPv4 header?

    1. It specifies the priority for quality of service
    2. It identifies the upper-layer protocol being carried
    3. It limits how many hops a packet can traverse Correct answer.
    4. It verifies the integrity of the IP header

    Explanation

    Each router decrements the TTL by one, and a packet is discarded when the TTL reaches zero. This prevents packets from looping indefinitely through a network.

  29. Question 29Network Fundamentals

    Which connector is commonly used with twisted-pair Ethernet cabling?

    1. BNC
    2. RJ-45 Correct answer.
    3. SC
    4. LC

    Explanation

    Twisted-pair Ethernet cables typically terminate with RJ-45 connectors. LC and SC are fiber-optic connectors, and BNC is used with coaxial cable.

  30. Question 30Network Fundamentals

    A switch receives a frame with a destination MAC address that is not in its MAC address table. What does the switch do?

    1. It floods the frame out all other ports Correct answer.
    2. It sends the frame to the default gateway
    3. It drops the frame and logs an error
    4. It replies with an ICMP unreachable message

    Explanation

    When the destination MAC address is unknown, the switch floods the frame out every port except the ingress port. This behavior is called unknown unicast flooding.

  31. Question 31Network Fundamentals

    Which IPv6 address identifies the local loopback interface?

    1. fe80::1
    2. ::1 Correct answer.
    3. ff02::1
    4. ::

    Explanation

    The IPv6 loopback address is ::1, which is equivalent in purpose to 127.0.0.1 in IPv4. The address :: is unspecified, fe80::/10 is link-local, and ff02::1 is the all-nodes multicast address.

  32. Question 32Network Fundamentals

    Which sequence shows the DHCP messages used when a client obtains an IPv4 address lease?

    1. Offer, Discover, Request, Acknowledge
    2. Discover, Request, Offer, Acknowledge
    3. Discover, Offer, Request, Acknowledge Correct answer.
    4. Request, Offer, Discover, Acknowledge

    Explanation

    DHCP uses the DORA sequence: Discover, Offer, Request, and Acknowledge. The client discovers servers, receives an offer, requests the offer, and receives acknowledgment.

  33. Question 33Network Fundamentals

    Which TCP header field tells the sender how much data the receiver can accept?

    1. Window size Correct answer.
    2. Checksum
    3. Urgent pointer
    4. Sequence number

    Explanation

    The TCP window size field advertises the amount of data the receiver is currently willing to accept. This supports flow control between the endpoints.

  34. Question 34Network Fundamentals

    Which protocol typically uses UDP port 514 to forward log messages to a collector?

    1. NetFlow
    2. NTP
    3. Syslog Correct answer.
    4. SNMP

    Explanation

    Syslog commonly uses UDP port 514 to send event and log messages to a central collector. SNMP, NetFlow, and NTP use different ports for their respective functions.

  35. Question 35Network Fundamentals

    What is the primary purpose of Spanning Tree Protocol in a switched Layer 2 network?

    1. To combine multiple links into one logical link
    2. To authenticate devices before they access the port
    3. To prevent Layer 2 forwarding loops Correct answer.
    4. To route packets between different VLANs

    Explanation

    Spanning Tree Protocol blocks redundant paths so that a Layer 2 topology remains loop-free. Without it, broadcast frames could circulate indefinitely and overwhelm the network.

  36. Question 36Network Fundamentals

    Which technology carries traffic for multiple VLANs over a single switch-to-switch link?

    1. VTP
    2. Port security
    3. EtherChannel
    4. 802.1Q tagging Correct answer.

    Explanation

    IEEE 802.1Q inserts a VLAN tag into Ethernet frames so that multiple VLANs can share a trunk link. The receiving switch reads the tag to determine the frame's VLAN membership.

  37. Question 37Network Fundamentals

    Which cloud characteristic lets a customer provision computing resources automatically without human interaction from the provider?

    1. High availability
    2. On-demand self-service Correct answer.
    3. Resource pooling
    4. Measured service

    Explanation

    On-demand self-service allows a customer to provision resources, such as virtual machines, through automation without requiring provider intervention. Resource pooling and measured service describe sharing and billing, not automatic provisioning.

  38. Question 38Network Fundamentals

    A host is configured with 192.168.10.130/26. What is the network address of its subnet?

    1. 192.168.10.128 Correct answer.
    2. 192.168.10.64
    3. 192.168.10.192
    4. 192.168.10.130

    Explanation

    A /26 mask has a block size of 64, producing subnets at .0, .64, .128, and .192. The address .130 falls within the .128 subnet, so its network address is 192.168.10.128.

  39. Question 39Network Fundamentals

    Which statement correctly distinguishes the control plane from the data plane in a router?

    1. The control plane builds routing information, while the data plane forwards packets. Correct answer.
    2. The control plane assigns MAC addresses, while the data plane resolves names.
    3. The control plane encrypts traffic, while the data plane authenticates users.
    4. The control plane forwards packets, while the data plane builds the routing table.

    Explanation

    The control plane runs routing protocols and builds the routing and forwarding tables. The data plane uses those tables to forward individual packets through the device.

  40. Question 40Network Fundamentals

    Two switches need more bandwidth and redundancy between them without STP blocking the extra links. Which solution should be used?

    1. Bundle the links into an EtherChannel Correct answer.
    2. Configure each link as an access port in a different VLAN
    3. Set all but one link to half duplex
    4. Enable BPDU guard on all connected ports

    Explanation

    An EtherChannel bundles parallel physical links into one logical link, and STP treats that bundle as a single path. All member links can then forward traffic while providing redundancy.

  41. Question 41Network Access

    Which statement describes a VLAN?

    1. A wireless client security profile.
    2. A physical cable segment connecting two hosts.
    3. A route between separate IP subnets.
    4. A logical broadcast domain on switches. Correct answer.

    Explanation

    A VLAN is a Layer 2 logical grouping that creates a separate broadcast domain on one or more switches. Devices in different VLANs require Layer 3 routing to communicate.

  42. Question 42Network Access

    Which switch port type carries traffic for one VLAN and typically connects to an end device?

    1. Access port Correct answer.
    2. Trunk port
    3. Routed port
    4. Tunnel port

    Explanation

    An access port is assigned to a single VLAN and normally connects to an end device such as a PC or printer. A trunk port carries traffic for multiple VLANs, usually between switches.

  43. Question 43Network Access

    On an 802.1Q trunk, frames in the native VLAN are sent in which form?

    1. Tagged with VLAN ID 1
    2. Double-tagged
    3. Tagged with a random VLAN ID
    4. Untagged Correct answer.

    Explanation

    802.1Q leaves native VLAN frames untagged, so both ends of the trunk must agree on the native VLAN. Tagged frames carry an explicit VLAN identifier.

  44. Question 44Network Access

    On a Cisco switch with default settings, which VLAN is assigned to all access ports?

    1. VLAN 1 Correct answer.
    2. VLAN 0
    3. VLAN 1005
    4. VLAN 10

    Explanation

    By default, all switch ports are access ports in VLAN 1. VLAN 1 is also the default native VLAN on trunk links.

  45. Question 45Network Access

    What is the primary purpose of Spanning Tree Protocol on a switched network?

    1. To encrypt frames between switches.
    2. To assign IP addresses to VLAN interfaces.
    3. To prevent Layer 2 switching loops. Correct answer.
    4. To route packets between VLANs.

    Explanation

    STP prevents Layer 2 loops by blocking redundant paths while keeping a loop-free topology. Without STP, broadcast frames could circulate indefinitely.

  46. Question 46Network Access

    In STP, which switch is elected as the root bridge?

    1. The switch with the lowest bridge ID. Correct answer.
    2. The switch with the highest priority value.
    3. The switch with the most active ports.
    4. The switch with the highest MAC address.

    Explanation

    The bridge ID combines priority and MAC address, and the lowest value wins the root election. With equal priorities, the lowest MAC address decides.

  47. Question 47Network Access

    What does the Cisco PortFast feature do on an access port?

    1. It elects the port as the spanning-tree root port.
    2. It moves an access port directly to forwarding. Correct answer.
    3. It blocks all incoming frames from entering the port.
    4. It converts the access port into an 802.1Q trunk.

    Explanation

    PortFast skips the listening and learning stages on an edge port so it enters forwarding immediately. It should be enabled only on ports connected to end devices to avoid creating loops.

  48. Question 48Network Access

    Which protocol is a vendor-neutral neighbor discovery protocol defined by IEEE 802.1AB?

    1. LLDP Correct answer.
    2. Cisco VTP
    3. Cisco CDP
    4. Cisco DTP

    Explanation

    LLDP is the IEEE 802.1AB vendor-neutral neighbor discovery protocol. CDP is Cisco proprietary, while DTP and VTP serve other switching functions.

  49. Question 49Network Access

    How many bits does the 802.1Q tag use for the VLAN identifier?

    1. 16 bits
    2. 10 bits
    3. 12 bits Correct answer.
    4. 8 bits

    Explanation

    The 802.1Q tag includes a 12-bit VLAN identifier, allowing VLAN IDs 0 through 4095, with 1 through 4094 usable. The tag also carries priority and other fields.

  50. Question 50Network Access

    Which command limits an 802.1Q trunk to carry only VLANs 10 and 20?

    1. switchport trunk allowed vlan 10,20 Correct answer.
    2. switchport access vlan 10,20
    3. switchport trunk native vlan 10,20
    4. switchport mode trunk vlan 10,20

    Explanation

    The switchport trunk allowed vlan command defines which VLANs may traverse a trunk. The native VLAN command sets only the untagged VLAN and does not create an allowed list.

  51. Question 51Network Access

    Which DTP mode actively sends messages to negotiate a trunk link?

    1. Dynamic auto (passive)
    2. Dynamic desirable Correct answer.
    3. Access (static)
    4. Trunk (static)

    Explanation

    Dynamic desirable actively sends DTP frames to request trunking. Dynamic auto waits passively and forms a trunk only if the other side initiates.

  52. Question 52Network Access

    Which statement describes a switch operating in VTP client mode?

    1. It forwards advertisements but cannot edit VLANs. Correct answer.
    2. It can create and delete VLANs locally.
    3. It ignores all VTP advertisements from the domain.
    4. It must be configured as the VTP server.

    Explanation

    A VTP client receives and forwards VTP advertisements but cannot modify the VLAN database. VTP servers can create and delete VLANs, while transparent switches keep a local database.

  53. Question 53Network Access

    Which three port states are defined by Rapid Spanning Tree Protocol?

    1. Blocking, listening, and forwarding
    2. Discarding, learning, and forwarding Correct answer.
    3. Listening, learning, and forwarding
    4. Disabled, blocking, and learning

    Explanation

    RSTP uses discarding, learning, and forwarding as its three port states. The older 802.1D STP uses blocking, listening, learning, and forwarding.

  54. Question 54Network Access

    Which IEEE standard defines Link Aggregation Control Protocol for EtherChannel?

    1. IEEE 802.1Q (VLAN tagging)
    2. IEEE 802.1X (port auth)
    3. IEEE 802.3ad (LACP) Correct answer.
    4. IEEE 802.1D (STP)

    Explanation

    LACP is defined by IEEE 802.3ad for dynamic link aggregation. PAgP is a Cisco proprietary alternative for EtherChannel negotiation.

  55. Question 55Network Access

    Which port security violation mode drops unauthorized frames and increments the violation counter?

    1. protect
    2. monitor
    3. shutdown
    4. restrict Correct answer.

    Explanation

    Restrict mode drops offending frames, increments the violation counter, and can generate log or SNMP messages. Protect mode drops silently, while shutdown err-disables the port.

  56. Question 56Network Access

    In DHCP snooping, which port should normally be configured as trusted?

    1. The uplink toward the DHCP server. Correct answer.
    2. A port with no devices connected.
    3. A port connected to an unmanaged hub.
    4. A port connected to an end-user workstation.

    Explanation

    DHCP server messages must enter through a trusted port, typically the uplink toward the legitimate DHCP server. Ports connected to clients remain untrusted.

  57. Question 57Network Access

    Dynamic ARP Inspection validates ARP packets using which source of binding information?

    1. The switch content-addressable memory.
    2. The VLAN Trunking Protocol database.
    3. The spanning-tree topology table.
    4. The DHCP snooping database. Correct answer.

    Explanation

    DAI checks ARP packets against DHCP snooping binding entries that associate IP address, MAC address, VLAN, and port. Invalid ARP packets are dropped.

  58. Question 58Network Access

    Which protocol forms the control and data tunnels between a lightweight access point and a wireless LAN controller?

    1. VTP (VLANs)
    2. STP (Layer 2)
    3. LWAPP (legacy)
    4. CAPWAP Correct answer.

    Explanation

    CAPWAP carries control and data traffic between a lightweight access point and a wireless LAN controller. It replaces the older LWAPP protocol.

  59. Question 59Network Access

    On a Cisco wireless LAN controller, which interface type carries client data for a particular VLAN?

    1. Virtual interface
    2. Service-port interface
    3. Dynamic interface Correct answer.
    4. Management interface

    Explanation

    Dynamic interfaces on a Cisco WLC map to VLANs and carry client data traffic. The management interface handles management and CAPWAP-related traffic.

  60. Question 60Network Access

    Which IEEE standard provides PoE up to approximately 30 W at the power sourcing equipment?

    1. 802.3ad
    2. 802.3at Correct answer.
    3. 802.3af
    4. 802.3ac

    Explanation

    802.3at, also called PoE+, provides up to about 30 W at the power sourcing equipment. 802.3af provides up to about 15.4 W.

  61. Question 61Network Access

    A trunk link between two switches has native VLAN 10 on one side and native VLAN 20 on the other. What is a likely result?

    1. A new root bridge is elected for the spanning tree.
    2. All allowed VLANs are automatically pruned from the trunk.
    3. The trunk link enters an error-disabled state.
    4. VLAN 10 frames arrive in VLAN 20 on the other side. Correct answer.

    Explanation

    When native VLANs differ, untagged frames from one native VLAN are placed into the other side's native VLAN. Cisco devices may also log a native VLAN mismatch via CDP.

  62. Question 62Network Access

    Which STP feature prevents a designated port from becoming a root port when it receives superior BPDUs?

    1. BPDU Guard
    2. Loop Guard
    3. PortFast
    4. Root Guard Correct answer.

    Explanation

    Root Guard blocks superior BPDUs on a port to prevent another switch from becoming the root bridge; the port enters a root-inconsistent state. BPDU Guard instead err-disables a port when any BPDU is received.

  63. Question 63Network Access

    Which statement describes EtherChannel load balancing on a Cisco switch?

    1. Frames are hashed across links using address fields. Correct answer.
    2. A single flow is split across all links in the channel.
    3. Only one member link forwards traffic at a time.
    4. All member links must use different speeds.

    Explanation

    EtherChannel uses a hash of address or port fields to select a member link for each flow. A single flow typically stays on one link, and member links must have matching configuration.

  64. Question 64Network Access

    Which encryption and integrity method is used by WPA2 in enterprise deployments?

    1. DES with SHA-1
    2. WEP with RC4
    3. TKIP with RC4
    4. AES with CCMP Correct answer.

    Explanation

    WPA2 uses AES with CCMP for encryption and integrity. WPA originally used TKIP, and WEP is an obsolete security method.

  65. Question 65Network Access

    What does the command ip dhcp snooping limit rate 10 configure?

    1. A limit of 10 DHCP messages per second on a port. Correct answer.
    2. A trusted state applied to the first 10 server ports.
    3. A maximum of 10 DHCP client leases in each VLAN.
    4. A DHCP lease time of 10 minutes for all clients.

    Explanation

    The ip dhcp snooping limit rate command sets a per-port rate limit for DHCP messages, commonly applied to untrusted ports. Excess messages can cause the port to be err-disabled.

  66. Question 66Network Access

    On an 802.1Q trunk between two switches, frames belonging to which VLAN are normally transmitted without a tag?

    1. The management VLAN
    2. Any VLAN above 1005
    3. The voice VLAN
    4. The native VLAN Correct answer.

    Explanation

    802.1Q inserts a tag carrying the VLAN ID into each frame, but frames on the native VLAN are exempt and travel untagged so that untagged traffic can still cross the link. Both ends of the trunk should agree on the native VLAN, otherwise traffic can be placed in the wrong VLAN. The default native VLAN is VLAN 1.

  67. Question 67Network Access

    Which value determines whether a switch becomes the root bridge of a spanning-tree topology?

    1. The highest bridge ID
    2. The lowest port priority on the switch
    3. The lowest bridge ID Correct answer.
    4. The number of active ports on the switch

    Explanation

    The bridge ID is made of the 2-byte bridge priority (32768 by default) plus the 6-byte MAC address, and the switch advertising the lowest bridge ID wins the election. Port counts play no part in the election. Port priority is used later, when a non-root switch chooses its root port.

  68. Question 68Network Access

    Which protocol is the vendor-neutral IEEE standard that lets a device advertise its identity, capabilities, and management address to directly connected neighbors?

    1. STP
    2. LLDP Correct answer.
    3. VTP
    4. CDP

    Explanation

    LLDP, defined by IEEE 802.1AB, is an open Layer 2 discovery protocol that advertises information to one hop only. CDP delivers similar information but is Cisco proprietary, so it only works between Cisco devices. Discovery protocols help map a topology before configuration changes are made.

  69. Question 69Network Access

    In a wireless LAN, what identifies a basic service set (BSS)?

    1. The SSID string configured on the controller
    2. The VLAN mapped to the WLAN
    3. The MAC address of the AP radio Correct answer.
    4. The channel number the AP is using

    Explanation

    The BSSID is the MAC address of the access point radio and uniquely identifies one BSS, that is, one AP's coverage cell. The SSID is the human-readable network name and is deliberately shared by many APs to form an extended service set. Clients learn the BSSID from beacon and probe response frames.

  70. Question 70Network Access

    How does a switch operating in VTP transparent mode handle VLAN information?

    1. It relays VTP advertisements without updating its own VLAN database Correct answer.
    2. It takes over as the VTP server when the current server becomes unavailable
    3. It adds and deletes VLANs and synchronizes those changes to every switch in the domain
    4. It drops all VTP advertisements it receives on its trunk ports

    Explanation

    In transparent mode a switch passes VTP advertisements along its trunk ports but keeps its own locally configured VLAN database, which is not overwritten by received updates. Server and client modes are the roles that create and synchronize VLAN information. Transparent mode exists mainly to extend a VTP domain across a switch that must keep independent VLAN settings.

  71. Question 71Network Access

    Which RSTP port state performs the functions of both the 802.1D blocking and listening states?

    1. Disabled
    2. Forwarding
    3. Discarding Correct answer.
    4. Learning

    Explanation

    RSTP condenses the five 802.1D states into three: discarding, learning, and forwarding. Discarding combines the old disabled, blocking, and listening conditions, so the port neither learns MAC addresses nor forwards frames. Learning still populates the MAC address table without forwarding user traffic.

  72. Question 72Network Access

    PortFast and BPDU Guard are both enabled on an access port. A BPDU arrives on that port. What is the result?

    1. The port stays up and resumes normal STP operation
    2. PortFast is removed from the port but the port stays up in forwarding
    3. The BPDU is discarded and the port remains in the forwarding state
    4. The port is placed in the err-disabled state Correct answer.

    Explanation

    BPDU Guard assumes a PortFast port is connected to an end device, so a received BPDU means an unauthorized switch or bridge has appeared; the port is therefore err-disabled. Recovery requires a manual shutdown and no shutdown, or errdisable recovery being configured. BPDU Guard protects the topology from loops introduced by an unexpected bridge.

  73. Question 73Network Access

    Which LACP mode actively sends negotiation packets in an attempt to build an EtherChannel?

    1. Auto
    2. Desirable
    3. Active Correct answer.
    4. Passive

    Explanation

    LACP uses the active and passive modes: active initiates negotiation while passive only responds. PAgP uses the desirable and auto modes instead. If both ends wait passively, or both are set to auto, the bundle never forms.

  74. Question 74Network Access

    A multilayer switch must route traffic between VLAN 10 and VLAN 20. Which configuration is required?

    1. Enable IP routing and assign each VLAN interface an address Correct answer.
    2. Place a port in each VLAN and connect those ports with a cable
    3. Create a trunk to an external router that routes between the VLANs
    4. Assign both VLAN interfaces addresses in the same subnet

    Explanation

    Each VLAN needs a switched virtual interface holding an address in that VLAN's subnet, and global IP routing must be enabled for the switch to forward between them. Hosts then use their VLAN's SVI address as the default gateway. Inter-VLAN routing depends on the SVIs being in different subnets.

  75. Question 75Network Access

    A port with port security in restrict violation mode receives a frame from an unknown source MAC address. What happens?

    1. The frame is forwarded and a violation counter is incremented
    2. The port is err-disabled and stays down until it is manually recovered
    3. The frame is dropped and logged, but the port stays up Correct answer.
    4. All secure MAC addresses are cleared and relearned automatically

    Explanation

    Restrict mode drops frames from unknown sources, increments the violation counter, and generates a syslog message and SNMP trap, while the interface stays up. Shutdown mode instead err-disables the port, and protect mode drops the traffic silently with no notification.

  76. Question 76Network Access

    A lightweight access point builds a CAPWAP tunnel to a wireless LAN controller. Which UDP port carries CAPWAP control traffic?

    1. 5247
    2. 1812
    3. 443
    4. 5246 Correct answer.

    Explanation

    CAPWAP separates the two tunnel functions by port: UDP 5246 carries control traffic such as AP discovery, join, and configuration, while UDP 5247 carries encapsulated client data. Both ports must be permitted between the AP and the controller. RADIUS and HTTPS use different ports entirely.

  77. Question 77Network Access

    A switch port is configured with the command switchport mode dynamic auto. When does that port become a trunk?

    1. Only when the device at the other end is also set to dynamic auto
    2. It never becomes a trunk; dynamic auto always stays an access port
    3. Whenever the port is connected to another switch, regardless of configuration
    4. Only when the device at the other end is set to trunk or desirable Correct answer.

    Explanation

    Dynamic auto waits passively and forms a trunk only when the far end asks for one by being set to trunk or desirable. If both ends are dynamic auto, neither initiates and the link stays an access port. Dynamic desirable is the mode that actively requests a trunk.

  78. Question 78Network Access

    An EtherChannel bundle of four FastEthernet links must forward a broadcast frame. How is the frame transmitted?

    1. The frame is dropped because broadcasts are not permitted over EtherChannel
    2. One copy is sent out a single member link chosen by the load-balancing hash Correct answer.
    3. A copy is sent out each of the four member links
    4. The frame is sent out the first member link, based on the lowest port number

    Explanation

    The bundle acts as one logical link, and the load-balancing hash of the frame's addresses and ports picks exactly one member link for each frame. A broadcast is therefore transmitted once, not duplicated, and is flooded only by the receiving switch if needed. Different flows may hash to different members, spreading the load.

  79. Question 79Network Access

    A new port whose access VLAN is 30 is added to an existing EtherChannel bundle whose members are all in VLAN 10. What happens?

    1. The new port is not bundled and remains a standalone port Correct answer.
    2. The bundle is torn down and rebuilt with VLAN 30 as the common VLAN
    3. The switch creates a second EtherChannel automatically for VLAN 30
    4. The new port joins the bundle and its VLAN assignment is changed to 10

    Explanation

    All member interfaces of an EtherChannel must match on speed, duplex, trunking mode, and allowed and native VLANs. A port that fails the match check is excluded from the bundle and stays standalone until its configuration is corrected. Nothing on the switch rewrites the port's configuration or rebuilds the channel automatically.

  80. Question 80Network Access

    How is an 802.1Q tag inserted into an Ethernet frame?

    1. The source MAC address is replaced by the VLAN identifier
    2. A 4-byte field is appended to the end of the frame, after the frame check sequence
    3. A 2-byte field is inserted before the destination MAC address
    4. A 4-byte field is inserted between the source MAC and the EtherType Correct answer.

    Explanation

    802.1Q inserts a 4-byte tag between the source MAC address and the original EtherType/Length field; it holds a 2-byte tag protocol identifier (0x8100) plus priority, drop-eligibility, and VLAN ID bits. The frame check sequence is then recalculated. Frames on the native VLAN are sent without the tag.

  81. Question 81IP Connectivity

    Which routing table code identifies a route that an administrator configured manually?

    1. C
    2. S Correct answer.
    3. D
    4. O

    Explanation

    Cisco IOS labels each route with a code showing how it was learned. S means the network was entered as a static route, while C means directly connected, O means OSPF, and D means EIGRP.

  82. Question 82IP Connectivity

    When two routes to the same destination prefix are learned from different routing sources, which value does the router compare first?

    1. The interface metric
    2. Administrative distance Correct answer.
    3. The route's prefix length in bits
    4. The next-hop IP address

    Explanation

    Administrative distance ranks the trustworthiness of the source that supplied a route, so it is compared before metrics when sources differ. Metrics are only compared between routes from the same protocol.

  83. Question 83IP Connectivity

    Which command creates an IPv4 default route on a Cisco router when the next hop is 10.1.1.1?

    1. ip route 0.0.0.0 255.255.255.255 10.1.1.1
    2. ip route 255.255.255.255 0.0.0.0 10.1.1.1
    3. ip default-gateway 10.1.1.1
    4. ip route 0.0.0.0 0.0.0.0 10.1.1.1 Correct answer.

    Explanation

    A default route matches every destination, which is written as network 0.0.0.0 with mask 0.0.0.0 in the ip route command. The resulting entry has a prefix length of /0.

  84. Question 84IP Connectivity

    How does OSPFv2 carry its messages across the network?

    1. ICMP, using type code 89
    2. UDP, using destination port 520
    3. TCP, using destination port 179
    4. IP, using protocol number 89 Correct answer.

    Explanation

    OSPFv2 is encapsulated directly in IP packets and is identified by IP protocol number 89. It does not use TCP or UDP, which is why it implements its own reliability mechanisms.

  85. Question 85IP Connectivity

    By default, how does a Cisco router derive the OSPF cost of an interface?

    1. Delay
    2. Reliability
    3. Bandwidth Correct answer.
    4. Load

    Explanation

    The default OSPF cost is the reference bandwidth divided by the interface bandwidth, with a minimum value of 1. Delay, reliability, and load are EIGRP metric components, not OSPF cost inputs.

  86. Question 86IP Connectivity

    A network engineer wants a backup static route to be used only when the primary OSPF route to the same prefix disappears. Which approach accomplishes this?

    1. Giving the static route a lower metric than the OSPF route
    2. Giving the static route a higher administrative distance Correct answer.
    3. Pointing a default route at the OSPF neighbor's address
    4. Giving the static route a lower administrative distance

    Explanation

    A floating static route is configured with an administrative distance higher than that of the dynamic protocol, so it stays out of the routing table while the dynamic route is present. When the dynamic route fails, the static route's distance makes it the best available path.

  87. Question 87IP Connectivity

    A router has routes 10.0.0.0/8, 10.1.0.0/16 (static), 10.1.0.0/16 (OSPF), and 10.1.1.0/24 (OSPF). A packet destined for 10.1.1.5 arrives. Which route is used?

    1. The 10.0.0.0/8 OSPF route
    2. The 10.1.0.0/16 OSPF route
    3. The 10.1.1.0/24 OSPF route Correct answer.
    4. The 10.1.0.0/16 static route

    Explanation

    Routers always select the longest matching prefix before considering administrative distance or metric. The /24 entry is the most specific match for 10.1.1.5, so it is chosen even though the static /16 has a better administrative distance.

  88. Question 88IP Connectivity

    Which command configures an IPv6 default route with next hop 2001:db8::1 on a Cisco router?

    1. ipv6 route ::/0 2001:db8::1 Correct answer.
    2. ipv6 route 0::/0 2001:db8::1
    3. ipv6 route ::/128 2001:db8::1
    4. ip route ::/0 2001:db8::1

    Explanation

    An IPv6 default route is the all-zero prefix ::/0 installed with the ipv6 route command. The prefix ::/0 matches every IPv6 destination.

  89. Question 89IP Connectivity

    A router has a loopback interface with address 10.1.1.1 and a physical interface with address 192.168.1.1. No router ID has been configured, and OSPF is enabled. Which value becomes the OSPF router ID?

    1. The value of the OSPF process ID
    2. The MAC address of the loopback interface
    3. 192.168.1.1
    4. 10.1.1.1 Correct answer.

    Explanation

    OSPF chooses the highest loopback address when no router-id is configured, because loopbacks stay up regardless of physical link state. Physical interface addresses are only considered when no loopback address exists.

  90. Question 90IP Connectivity

    What does the passive-interface command do to an interface running OSPF?

    1. It stops hellos there but still advertises the network Correct answer.
    2. It shuts down the interface administratively
    3. It sets the interface cost to the maximum value
    4. It prevents the connected network from being advertised

    Explanation

    Making an interface passive suppresses OSPF hello packets on that interface so no neighbors can form there, but the connected subnet is still included in the router's LSAs. This is typical on interfaces facing end-user LANs.

  91. Question 91IP Connectivity

    Two routers on the same Ethernet segment are configured with OSPF but their interfaces are placed in different areas. What is the result?

    1. They will reach 2-way state and exchange LSAs normally
    2. They will become neighbors only if their router IDs match
    3. They will not become neighbors because the area IDs differ Correct answer.
    4. They will form a neighbor relationship but not exchange routes

    Explanation

    Area ID is one of the fields carried in the OSPF hello packet, and routers must agree on it before an adjacency can form. A mismatch leaves both routers hearing hellos but discarding them, so no neighbor relationship develops.

  92. Question 92IP Connectivity

    What is the role of the designated router on an OSPF broadcast multiaccess segment?

    1. It reduces the number of adjacencies formed on the segment Correct answer.
    2. It computes shortest paths for the entire area
    3. It assigns IPv4 addresses to the other routers on the segment
    4. It redistributes external routes into the area

    Explanation

    On a broadcast segment, every router would otherwise have to peer with every other router. Electing a DR and BDR limits full adjacencies and centralizes LSA flooding, which scales the topology.

  93. Question 93IP Connectivity

    What is the purpose of a first hop redundancy protocol such as HSRP?

    1. To translate private addresses into public addresses
    2. To authenticate routing updates between OSPF neighbors
    3. To balance traffic across parallel links to the same destination
    4. To provide a virtual default gateway if a router fails Correct answer.

    Explanation

    Hosts are configured with a single default gateway, so FHRPs present a virtual IP and MAC address shared by a group of routers. If the active router fails, another group member takes over the virtual address and hosts keep forwarding.

  94. Question 94IP Connectivity

    A static route that specifies a next-hop IP address has which default administrative distance on a Cisco router?

    1. 5
    2. 0
    3. 90
    4. 1 Correct answer.

    Explanation

    Static routes carry an administrative distance of 1 by default, placing them ahead of all dynamic routing protocols. Connected routes have distance 0, EIGRP internal routes 90, and OSPF routes 110.

  95. Question 95IP Connectivity

    Which OSPF network type is assigned by default to a point-to-point serial link?

    1. Point-to-point Correct answer.
    2. Point-to-multipoint
    3. Broadcast
    4. Non-broadcast

    Explanation

    On a point-to-point link, OSPF uses the point-to-point network type, which forms an adjacency without a DR/BDR election and sends hellos every 10 seconds. Broadcast and non-broadcast are the defaults for multiaccess media.

  96. Question 96IP Connectivity

    Two OSPF routers remain stuck in the EXSTART/EXCHANGE state. Which condition most likely explains this?

    1. A mismatch in the OSPF area IDs
    2. A mismatch in the interface MTU values Correct answer.
    3. A mismatch in the OSPF process IDs
    4. A mismatch in the hello and dead timer values

    Explanation

    The master/slave negotiation and database description exchange compare MTU values, so mismatched MTUs stall the adjacency in EXSTART or EXCHANGE. Timer or area mismatches stop the routers much earlier, before they reach that stage.

  97. Question 97IP Connectivity

    A router learns 192.168.1.0/24 from both OSPF and EIGRP. Which route is installed in the routing table?

    1. The EIGRP route, because of administrative distance Correct answer.
    2. Neither route, until the metrics are equalized
    3. Both routes, because the prefix lengths match
    4. The OSPF route, because of its lower metric

    Explanation

    When the same prefix is offered by different sources, the router compares administrative distance before metric. EIGRP internal routes (90) are preferred over OSPF routes (110), so the EIGRP path is installed.

  98. Question 98IP Connectivity

    An interface has a bandwidth of 1544 kbps and the default OSPF reference bandwidth is in use. What cost does OSPF assign to it?

    1. 64 Correct answer.
    2. 154
    3. 65
    4. 48

    Explanation

    Cost equals the reference bandwidth (100,000,000) divided by the interface bandwidth in bits per second, with the result truncated to an integer. 100,000,000 divided by 1,544,000 is about 64.77, which becomes 64.

  99. Question 99IP Connectivity

    Which OSPF router command causes a default route to be advertised into the OSPF area?

    1. ip default-network 0.0.0.0
    2. default-information originate Correct answer.
    3. network 0.0.0.0 0.0.0.0 area 0
    4. redistribute static subnets

    Explanation

    The default-information originate command injects a type 5 LSA carrying 0.0.0.0/0 into the OSPF domain, provided the router has a default route or the always keyword is used. Neighbors then use the advertising router as their gateway of last resort.

  100. Question 100IP Connectivity

    A static route on a multiaccess Ethernet network is configured with an exit interface only. What is a consequence of this design?

    1. The administrative distance rises automatically
    2. The route is not installed until a next hop address is specified
    3. The router drops packets because no next hop is reachable
    4. The router must ARP for each destination, filling the ARP cache Correct answer.

    Explanation

    With only an exit interface on a multiaccess link, the router treats each destination as directly connected and sends an ARP request for every destination address, which can exhaust the ARP cache. Specifying a next-hop address avoids this behavior.

  101. Question 101IP Connectivity

    What does a route with the code C in the routing table represent?

    1. A route learned from another router by a routing protocol
    2. A route manually configured by an administrator
    3. A network directly attached to a router interface Correct answer.
    4. A candidate default route for the router

    Explanation

    The C code marks a connected network, which is added automatically when an interface is up and has an IP address and mask. Connected routes have an administrative distance of 0.

  102. Question 102IP Connectivity

    Which first hop redundancy protocol can distribute client traffic across multiple gateways at the same time?

    1. GLBP Correct answer.
    2. VRRP
    3. STP
    4. HSRP

    Explanation

    GLBP elects an active virtual gateway and multiple active virtual forwarders, so several routers can forward traffic for the same virtual IP simultaneously. HSRP and VRRP keep one gateway active per group.

  103. Question 103IP Connectivity

    Which command must be enabled on a Cisco router before it will forward IPv6 packets between interfaces?

    1. ipv6 enable
    2. ipv6 address autoconfig
    3. ipv6 unicast-routing Correct answer.
    4. ipv6 route ::/0

    Explanation

    IPv6 routing is disabled by default, and the ipv6 unicast-routing global command turns the router into an IPv6 forwarder. Without it, the router can still have IPv6 addresses but will not route between interfaces.

  104. Question 104IP Connectivity

    A router has two OSPF routes to the same destination with identical cost. What does the router do by default?

    1. It installs both routes and shares traffic across them Correct answer.
    2. It waits until the costs differ before installing either
    3. It picks the path with the lowest neighbor router ID
    4. It keeps only the first route learned and discards the other

    Explanation

    OSPF supports equal-cost multipath, so paths with the same metric are all installed and traffic is load-balanced across them. Cisco IOS allows up to four equal-cost paths by default.

  105. Question 105IP Connectivity

    What are the default OSPF hello and dead intervals on an Ethernet interface?

    1. 10 seconds hello, 40 seconds dead Correct answer.
    2. 40 seconds hello, 10 seconds dead
    3. 10 seconds hello, 30 seconds dead
    4. 30 seconds hello, 120 seconds dead

    Explanation

    On broadcast and point-to-point interfaces, OSPF sends hellos every 10 seconds and declares a neighbor down after 40 seconds without a hello. The 30/120 values apply to NBMA and point-to-multipoint network types.

  106. Question 106IP Connectivity

    In the output of the show ip route command, which code identifies a network that is directly attached to a router interface?

    1. S
    2. O
    3. D
    4. C Correct answer.

    Explanation

    The routing table prefixes routes with a code showing how the route was learned. C marks a connected network, meaning an interface on the router is up with an address in that subnet. S marks a static route, O marks OSPF, and D marks EIGRP.

  107. Question 107IP Connectivity

    Which command creates an IPv4 default route that sends matching traffic to next hop 10.1.1.1?

    1. ip route 0.0.0.0 0.0.0.0 10.1.1.1 Correct answer.
    2. ip route 10.1.1.0 255.255.255.0 10.1.1.1
    3. ip route 255.255.255.255 0.0.0.0 10.1.1.1
    4. ip default-gateway 10.1.1.1

    Explanation

    A default route matches every destination, which is expressed as the network 0.0.0.0 with the mask 0.0.0.0. The static route syntax is ip route <network> <mask> <next-hop>, so the all-zero prefix produces the default route.

  108. Question 108IP Connectivity

    What is the default administrative distance of a static route?

    1. 1 Correct answer.
    2. 90
    3. 110
    4. 0

    Explanation

    Administrative distance ranks the trustworthiness of route sources, and a static route defaults to 1. Only a directly connected route, at distance 0, is preferred over it. Dynamic protocols such as EIGRP (90) and OSPF (110) are trusted less by default.

  109. Question 109IP Connectivity

    A routing table contains the entries 0.0.0.0/0, 10.0.0.0/8, 10.1.0.0/16, and 10.1.4.0/24. A packet arrives with destination address 10.1.4.77. Which entry is used to forward it?

    1. 10.1.0.0/16
    2. 0.0.0.0/0
    3. 10.0.0.0/8
    4. 10.1.4.0/24 Correct answer.

    Explanation

    A router first applies the longest prefix match among all routes that contain the destination. All four entries match 10.1.4.77, but /24 is the most specific mask, so it wins regardless of administrative distance or metric.

  110. Question 110IP Connectivity

    A routing table shows the line Gateway of last resort is 203.0.113.1 to network 0.0.0.0. What does this line indicate?

    1. No routes are installed except host routes.
    2. The next hop 203.0.113.1 is unreachable.
    3. A default route is present in the routing table. Correct answer.
    4. 203.0.113.1 is the OSPF router ID of this router.

    Explanation

    The gateway of last resort is the router's candidate default route, used for any destination that has no more specific match. It appears when a default route such as 0.0.0.0/0 is installed from any source.

  111. Question 111IP Connectivity

    Which IPv4 multicast address do OSPFv2 routers use to send hello packets?

    1. 224.0.0.6
    2. 224.0.0.9
    3. 224.0.0.10
    4. 224.0.0.5 Correct answer.

    Explanation

    OSPFv2 sends hellos and other control traffic to the AllSPFRouters address 224.0.0.5. The address 224.0.0.6 (AllDRouters) is used by the DR and BDR to receive updates from other routers.

  112. Question 112IP Connectivity

    What is the main purpose of a first hop redundancy protocol such as HSRP or VRRP?

    1. To provide a resilient default gateway to hosts. Correct answer.
    2. To authenticate routing updates between neighbors.
    3. To translate private addresses into public addresses.
    4. To load balance traffic across equal-cost paths.

    Explanation

    First hop redundancy protocols group two or more routers behind one shared virtual IP and MAC address. Hosts use that virtual address as their default gateway, so if the active router fails the standby takes over with no host reconfiguration.

  113. Question 113IP Connectivity

    By default, OSPF derives the cost of an interface from which value?

    1. Interface bandwidth Correct answer.
    2. The number of router hops to the destination
    3. A composite of bandwidth and delay
    4. The administrative distance of the interface

    Explanation

    OSPF cost is calculated as the reference bandwidth (100 Mbps by default) divided by the interface bandwidth, so faster links receive lower costs. The cost of a route is the sum of the costs of the outgoing interfaces along the path.

  114. Question 114IP Connectivity

    A floating static route for 172.16.0.0/16 with administrative distance 200 is configured, while OSPF also learns the same prefix. When does the static route appear in the routing table?

    1. Always, because static routes are preferred over dynamic routes
    2. Never, because two routes to the same prefix cannot coexist in the configuration
    3. Only when the OSPF route to that prefix leaves the routing table Correct answer.
    4. Only when the OSPF route's metric exceeds 200

    Explanation

    When two sources offer the same prefix, only the route with the lowest administrative distance is installed. Setting a static route's distance above the dynamic protocol's distance makes it a backup that is installed only after the dynamic route is withdrawn.

  115. Question 115IP Connectivity

    An OSPFv2 router has no router-id configured. Loopback0 is 10.5.5.5, Loopback1 is 10.9.9.9, and its physical interfaces are 192.168.1.1 and 172.16.1.1. Which value becomes the OSPF router ID?

    1. 10.9.9.9 Correct answer.
    2. 172.16.1.1
    3. 10.5.5.5
    4. 192.168.1.1

    Explanation

    With no explicit router-id, OSPF uses the highest IPv4 address among any active loopback interfaces. Physical interface addresses are considered only if no loopback address exists.

  116. Question 116IP Connectivity

    Two routers on the same Ethernet segment fail to form an OSPF adjacency. Which mismatch would prevent the adjacency from forming?

    1. Different hostnames
    2. Different static routes
    3. Different hello and dead intervals Correct answer.
    4. Different OSPF process IDs

    Explanation

    OSPF neighbors must agree on the hello and dead timers, area ID, authentication, stub area flags, and MTU before they can become adjacent. The process ID and hostname are locally significant and do not need to match.

  117. Question 117IP Connectivity

    What does the passive-interface command do to an OSPF-enabled interface?

    1. It suppresses hellos but still advertises the subnet. Correct answer.
    2. It blocks all user traffic from passing through the interface.
    3. It removes the interface from the OSPF process entirely.
    4. It sets the interface OSPF cost to the maximum value.

    Explanation

    A passive interface stops OSPF from sending hellos and forming adjacencies out of that interface, which is typical for links facing end hosts. The subnet is still included in the router's LSAs and advertised to other OSPF routers.

  118. Question 118IP Connectivity

    On a multi-access Ethernet link, a static route is configured with only an exit interface and no next-hop address. What is the result?

    1. The route is converted into a default route.
    2. The router must resolve each destination address with ARP. Correct answer.
    3. The router uses its own MAC address as the next hop.
    4. The route is rejected because the exit interface is not point-to-point.

    Explanation

    On a broadcast link the router treats every destination as directly connected out of that interface, so it must ARP for each destination IP before it can build a frame. This is why a next-hop address is normally included on multi-access links, while exit-interface-only routes are appropriate on point-to-point links.

  119. Question 119IP Connectivity

    Two routers run HSRP on the same subnet. Router A has priority 100 and IP 10.0.0.2; Router B has priority 150 and IP 10.0.0.3. Which router becomes the active router?

    1. Router B, because it has the highest priority Correct answer.
    2. Router A, because it has the highest IP address
    3. Router A, because it has the lowest IP address
    4. Both routers are active and share the virtual IP

    Explanation

    HSRP first compares interface priority, and the higher value wins; the default priority is 100. The IP address is used only as a tiebreaker when priorities are equal, with the higher address winning.

  120. Question 120IP Connectivity

    Which statement about VRRP is true when compared with HSRP?

    1. VRRP is a Cisco-proprietary protocol.
    2. VRRP uses TCP port 1985 for hello messages.
    3. VRRP can use a real interface address as the virtual IP. Correct answer.
    4. VRRP elects a standby router that never forwards traffic.

    Explanation

    VRRP is an open standard, and a router is allowed to use its own interface address as the shared virtual address. HSRP is Cisco proprietary and requires the virtual address to be distinct from all real interface addresses.

  121. Question 121IP Connectivity

    A routing table entry reads O 10.2.2.0/24 [110/20] via 10.1.1.2. What do the bracketed values represent?

    1. Cost 110 and MTU 20
    2. Administrative distance 110 and metric 20 Correct answer.
    3. Router ID 110 and hop count 20
    4. Metric of 110 and administrative distance of 20

    Explanation

    Cisco routing table output prints the bracketed pair as [administrative distance/metric]. Here the OSPF route has the default distance 110 and a total path cost of 20.

  122. Question 122IP Connectivity

    When configuring an IPv6 static route that specifies a link-local address as the next hop, what must also be included?

    1. An administrative distance lower than 1
    2. The global unicast address of the neighbor
    3. The outgoing interface Correct answer.
    4. A /128 prefix length for the destination

    Explanation

    Link-local addresses are unique only on a single link, so an IPv6 router cannot resolve a link-local next hop without knowing which interface to send the packet out of. The route is written as ipv6 route <prefix> <interface> <link-local next hop>.

  123. Question 123IP Connectivity

    Using the default OSPF reference bandwidth of 100 Mbps, what cost is assigned to a 10 Mbps interface?

    1. 100
    2. 1000
    3. 1
    4. 10 Correct answer.

    Explanation

    OSPF cost equals reference bandwidth divided by interface bandwidth, so 100 Mbps divided by 10 Mbps gives 10. Costs are whole numbers, with values below 1 rounded up to 1.

  124. Question 124IP Connectivity

    On an OSPF broadcast network, which two values decide which router becomes the designated router?

    1. Lowest priority value, then highest router ID
    2. Lowest cost, then highest priority
    3. Highest priority, then highest router ID Correct answer.
    4. Highest router ID, then highest IP address

    Explanation

    The interface with the highest OSPF priority becomes the DR, and the router ID breaks a tie. The default priority is 1, and a priority of 0 makes a router ineligible to become DR or BDR.

  125. Question 125IP Connectivity

    A router has a default route in its table and must inject it into OSPF so other routers learn it. Which command accomplishes this?

    1. default-information originate Correct answer.
    2. redistribute static
    3. network 0.0.0.0 0.0.0.0 area 0
    4. default-route ospf

    Explanation

    The default-information originate command makes an OSPF router advertise 0.0.0.0/0 into its area, provided a default route already exists locally. Adding the always keyword causes the advertisement even when no local default route is present.

  126. Question 126IP Connectivity

    A router has a floating static route to 192.168.7.0/24 with administrative distance 200, an OSPF route with distance 110, and an EIGRP route with distance 90 for the same prefix. Which route is installed?

    1. The EIGRP route Correct answer.
    2. The OSPF and EIGRP routes, load balanced
    3. The OSPF route
    4. The floating static route

    Explanation

    For a single prefix, the router installs only the route from the source with the lowest administrative distance; metrics are compared only among routes from the same source. EIGRP at 90 is lower than OSPF at 110 and the static route at 200, so the EIGRP route wins.

  127. Question 127IP Connectivity

    Which statement describes how OSPFv3 differs from OSPFv2?

    1. OSPFv3 uses a 16-bit metric field.
    2. OSPFv3 uses the multicast address 224.0.0.5.
    3. OSPFv3 requires the network command under the OSPF process.
    4. OSPFv3 runs on interfaces and uses link-local next hops. Correct answer.

    Explanation

    OSPFv3 is enabled directly on interfaces with the ipv6 ospf command rather than through network statements, and IPv6 next hops are taken from the neighbor's link-local address. It also uses its own multicast addresses, FF02::5 and FF02::6, for hello and DR traffic.

  128. Question 128IP Connectivity

    Router A is the HSRP active router with priority 110. A new Router B with priority 150 joins the group, but Router A remains active. What explains this?

    1. HSRP elects the router with the lowest IP address.
    2. Router B does not have a virtual IP address configured for the group.
    3. Router B has a lower priority than Router A.
    4. Preemption is disabled, so the active router keeps its role. Correct answer.

    Explanation

    Preemption is disabled by default in HSRP, so a newly arriving higher-priority router stays in the standby role and the current active router keeps forwarding. The standby preempt command is required for the higher-priority router to take over.

  129. Question 129IP Connectivity

    A static route to 192.168.50.0/24 points to next hop 10.1.1.1, which the router reaches through an OSPF route. If OSPF withdraws the route to 10.1.1.1, what happens to the static route?

    1. It stays in the table and traffic is dropped at the next hop.
    2. It is converted into a directly connected route.
    3. It is removed because its next hop can no longer be resolved. Correct answer.
    4. It remains but with the administrative distance raised to 255.

    Explanation

    Before installing a static route, the router performs a recursive lookup to confirm the next hop is reachable through another route. When the resolving route disappears, the static route becomes invalid and is withdrawn from the routing table.

  130. Question 130IP Connectivity

    Two OSPF routes to 10.10.0.0/16 are learned with equal cost 20 through two different next hops. What does the router do by default?

    1. It installs both routes and load balances across them. Correct answer.
    2. It discards both routes until the costs differ.
    3. It installs only the first route that was learned.
    4. It installs only the route with the lowest next-hop address.

    Explanation

    When a routing protocol offers multiple paths to the same prefix with equal metrics, IOS installs them all and performs equal-cost load balancing, up to four paths by default. No tiebreaker is applied to the next-hop address.

  131. Question 131IP Services

    During the DHCP process, which message does a DHCP server send to propose an IPv4 address to a client?

    1. DHCPDISCOVER
    2. DHCPREQUEST
    3. DHCPACK
    4. DHCPOFFER Correct answer.

    Explanation

    A server answers the client's broadcast DHCPDISCOVER with a DHCPOFFER that proposes an address along with lease and option parameters. The client then sends DHCPREQUEST for the offer it wants, and the server confirms it with DHCPACK.

  132. Question 132IP Services

    A router interface faces a LAN of DHCP clients, and the DHCP server sits on a different subnet. Which interface command forwards the clients' requests to that server?

    1. ip helper-address 10.1.1.10 Correct answer.
    2. ip dhcp pool 10.1.1.10
    3. ip dhcp relay-agent 10.1.1.10
    4. ip forward-protocol udp 67

    Explanation

    Routers do not forward subnet broadcast traffic, so the client's broadcast would die at the router. The ip helper-address command converts the DHCP broadcast into a unicast packet addressed to the specified server on the remote subnet.

  133. Question 133IP Services

    Which NAT feature allows many inside hosts to share a single registered public IPv4 address?

    1. Static NAT with a one-to-one mapping
    2. PAT using the overload keyword Correct answer.
    3. NAT64 translation
    4. Dynamic NAT with a pool of public addresses

    Explanation

    Port address translation tracks the source port numbers of the inside flows and rewrites them so many hosts can multiplex over one public address. It is configured on Cisco routers with the overload keyword.

  134. Question 134IP Services

    Which syslog severity level represents the most severe condition?

    1. Level 7
    2. Level 0 Correct answer.
    3. Level 1
    4. Level 4

    Explanation

    Syslog severities are numbered from 0 to 7, and the lower the number the more severe the event. Level 0 means the system is unusable, whereas level 7 is debugging output.

  135. Question 135IP Services

    Which transport protocol and port number does TFTP use?

    1. UDP port 69 Correct answer.
    2. UDP port 21
    3. TCP port 21
    4. TCP port 69

    Explanation

    TFTP is a simple file-transfer protocol that runs over UDP port 69 and provides its own acknowledgment mechanism at the application layer. It has no authentication and no directory listing capability.

  136. Question 136IP Services

    An administrator is in VTY line configuration mode on a router and wants those lines to accept only SSH sessions. Which command accomplishes this?

    1. ip ssh version 2
    2. transport input ssh Correct answer.
    3. login local
    4. transport output ssh

    Explanation

    Under line configuration, transport input controls which protocols the router accepts on the VTY lines. Setting transport input ssh makes the lines reject Telnet and accept SSH only.

  137. Question 137IP Services

    A router is synchronized to a stratum 1 NTP server, and show ntp status reports stratum 2. What does the value 2 represent?

    1. It is configured as an NTP master with stratum 2.
    2. It is the reference clock that all other devices in the network follow.
    3. It is one stratum level below a stratum 1 server. Correct answer.
    4. It has lost synchronization with its time source.

    Explanation

    Stratum counts how many steps a device is from the reference clock. Stratum 1 devices attach directly to a reference clock, so a device synchronized to one of them reports stratum 2.

  138. Question 138IP Services

    Which statement describes the purpose of static NAT?

    1. It translates IPv6 addresses into IPv4 addresses.
    2. It shares one public address among many inside hosts.
    3. It permanently binds one inside address to one public address. Correct answer.
    4. It assigns an address from a pool of public addresses in rotation.

    Explanation

    Static NAT creates a fixed one-to-one translation between an inside local address and an inside global address. It is used for devices such as web servers that must always be reachable from the internet at a predictable address.

  139. Question 139IP Services

    How does an SNMP inform differ from an SNMP trap?

    1. The inform carries a complete copy of the MIB.
    2. The inform is acknowledged by the manager; a trap is not. Correct answer.
    3. The inform is encrypted with SNMPv3 while a trap is not.
    4. The inform is sent only when the manager polls the agent.

    Explanation

    Both messages are pushed by the agent without a request, but an inform is a confirmed notification: the manager must respond, and the agent retransmits if no response arrives. A trap is fire-and-forget, so a lost trap is never noticed.

  140. Question 140IP Services

    Which command prevents the router's DHCP server from assigning the addresses 10.1.1.1 through 10.1.1.10?

    1. ip dhcp pool 10.1.1.0 255.255.255.0
    2. ip dhcp-server excluded 10.1.1.1 through 10.1.1.10
    3. ip address dhcp 10.1.1.1 10.1.1.10
    4. ip dhcp excluded-address 10.1.1.1 10.1.1.10 Correct answer.

    Explanation

    The ip dhcp excluded-address command reserves a range so the router's DHCP server never hands those addresses out. Administrators use it for gateways, servers, and printers that are configured with static addresses.

  141. Question 141IP Services

    Which statement describes traffic shaping?

    1. It buffers excess traffic and forwards it later. Correct answer.
    2. It compresses excess traffic before transmission.
    3. It drops excess traffic immediately at the interface.
    4. It reclassifies excess traffic to a lower priority queue.

    Explanation

    Shaping smooths bursts by holding packets that exceed the configured rate in a buffer and releasing them later, so the average rate stays within the limit. Policing instead enforces the rate by dropping or remarking the excess.

  142. Question 142IP Services

    The Differentiated Services field of the IPv4 header is divided into which two components?

    1. A 3-bit precedence field and a 5-bit ECN field
    2. A 6-bit DSCP field and a 2-bit ECN field Correct answer.
    3. A 5-bit DSCP field and a 3-bit ECN field
    4. A 4-bit priority field and a 4-bit ECN field

    Explanation

    The Type of Service byte is redefined as the DS field: the upper 6 bits hold the DSCP value that selects the per-hop behavior, and the lower 2 bits carry Explicit Congestion Notification.

  143. Question 143IP Services

    Which DNS record type maps an IPv4 address back to a hostname?

    1. PTR Correct answer.
    2. A
    3. MX
    4. CNAME

    Explanation

    PTR records live in the reverse lookup zone (in-addr.arpa for IPv4) and resolve an address to a name. Forward lookups that resolve a name to an IPv4 address use A records instead.

  144. Question 144IP Services

    A technician must copy a router configuration file to a server and needs authentication plus guaranteed delivery. Which protocol should be used?

    1. TFTP
    2. SNMP
    3. NTP
    4. FTP Correct answer.

    Explanation

    FTP runs over TCP, supports username and password authentication, and retransmits lost data, so it is the better choice when integrity and access control matter. TFTP is a lightweight UDP protocol with no authentication.

  145. Question 145IP Services

    Which command generates the key pair that a Cisco router uses for SSH?

    1. username admin privilege 15 secret cisco
    2. ip ssh version 2
    3. transport input ssh
    4. crypto key generate rsa Correct answer.

    Explanation

    SSH encrypts the session with an RSA key pair, which is created by crypto key generate rsa; a hostname and a domain name must already be configured. Until the keys exist, SSH cannot be enabled on the VTY lines.

  146. Question 146IP Services

    Which statement describes SNMPv3?

    1. It requires a separate MIB for each managed device.
    2. It replaces traps with syslog messages.
    3. It uses community strings sent in clear text.
    4. It authenticates and encrypts SNMP messages. Correct answer.

    Explanation

    SNMPv3 adds user-based authentication and privacy, meaning messages can be both authenticated and encrypted. SNMPv1 and v2c rely on plain-text community strings for access control.

  147. Question 147IP Services

    An administrator enters logging trap 4 on a router that sends messages to a syslog server. Which messages reach the server?

    1. All severity levels 0 through 7
    2. Severity levels 4 through 7
    3. Only severity level 4
    4. Severity levels 0 through 4 Correct answer.

    Explanation

    The logging trap value is a threshold, and severity levels run from 0 (most severe) to 7 (debugging). Setting 4 therefore sends every message at level 0 through level 4 and suppresses the less severe ones.

  148. Question 148IP Services

    In a well-designed QoS deployment, where should classification and marking be performed?

    1. Only after the traffic reaches the WAN link
    2. On each core router, because congestion happens there
    3. At the edge, as close to the source as possible Correct answer.
    4. On the service provider's routers, using their own policy

    Explanation

    Marking near the source lets every downstream device queue and drop traffic based on the existing marking, which avoids repeated deep inspection of the same flows. Core devices can then trust the markings and simply apply per-hop behavior.

  149. Question 149IP Services

    A DHCP client needs the address of a default gateway so it can reach remote subnets. Which DHCP option supplies it?

    1. Option 51
    2. Option 3 Correct answer.
    3. Option 53
    4. Option 6

    Explanation

    DHCP options carry extra configuration parameters in the offer; option 3 carries the default gateway, listed as the router option. Option 1 is the subnet mask and option 6 is the DNS server list.

  150. Question 150IP Services

    Which DNS record type delegates a subdomain to an authoritative name server in another zone?

    1. CNAME
    2. PTR
    3. NS Correct answer.
    4. MX

    Explanation

    NS records name the authoritative servers for a zone, so a parent domain can point resolvers to the servers that hold the data for a delegated child domain. This is how the DNS hierarchy is split into separately managed zones.

  151. Question 151Security Fundamentals

    Which term describes a weakness or flaw in a system that a threat actor could take advantage of?

    1. A threat
    2. A vulnerability Correct answer.
    3. An exploit
    4. A risk

    Explanation

    A vulnerability is a weakness in software, configuration, or procedure that could be leveraged to cause harm. Threats are potential sources of danger, exploits are the tools or techniques that abuse a weakness, and risk combines likelihood with impact.

  152. Question 152Security Fundamentals

    Which command stores the privileged EXEC password as a strong hash rather than clear text or weak reversible encoding?

    1. enable secret cisco Correct answer.
    2. username admin secret cisco
    3. service password-encryption
    4. enable password cisco

    Explanation

    The enable secret command stores the privileged EXEC password using a hash produced by a strong algorithm, so the original password cannot be recovered from the configuration file. The enable password command stores the value in clear text or with weak, reversible encoding.

  153. Question 153Security Fundamentals

    Which measure best protects the confidentiality of administrative CLI sessions to a router?

    1. Configuring a login banner
    2. Enabling SSH version 2 and disabling Telnet Correct answer.
    3. Configuring exec-timeout on the vty lines
    4. Applying an ACL that permits only the admin subnet

    Explanation

    Telnet sends every keystroke, including credentials, in clear text, so the session can be captured by anyone on the path. SSH version 2 encrypts the entire session, which preserves confidentiality of administrative traffic.

  154. Question 154Security Fundamentals

    Which AAA function records what a user did and when, including the commands that were issued?

    1. Accounting Correct answer.
    2. Authorization
    3. Access control
    4. Authentication

    Explanation

    The accounting function of AAA logs what an authenticated user did, such as the commands entered and the duration of a session. Authentication verifies identity, while authorization determines which resources the identity may use.

  155. Question 155Security Fundamentals

    What is the primary purpose of a DMZ in a network design?

    1. To centralize DHCP and DNS for all VLANs
    2. To isolate public servers from internal hosts Correct answer.
    3. To provide a backup path for WAN links
    4. To encrypt traffic between remote sites

    Explanation

    A DMZ is a segment that hosts services reachable from the internet while keeping them separated from the internal network by firewalls. If a public server is compromised, the attacker must still cross another control point to reach internal hosts.

  156. Question 156Security Fundamentals

    An employee receives an email that appears to come from the IT department and asks them to confirm their password on a linked website. Which attack is this?

    1. A man-in-the-middle attack
    2. A denial-of-service attack
    3. A brute-force attack
    4. A phishing attack Correct answer.

    Explanation

    Phishing uses a fraudulent message that impersonates a trusted party to trick the recipient into revealing credentials or clicking a malicious link. Brute force guesses credentials, man-in-the-middle intercepts traffic, and denial-of-service attacks exhaust resources.

  157. Question 157Security Fundamentals

    Which combination is an example of multifactor authentication?

    1. A username and its matching password
    2. Two passwords chosen by the user
    3. A password plus a security question
    4. A password plus a one-time code Correct answer.

    Explanation

    Multifactor authentication requires factors from different categories: something you know, something you have, and something you are. A password is knowledge and a one-time code from a token or app is possession, so the two together satisfy the requirement.

  158. Question 158Security Fundamentals

    Which statement describes a site-to-site VPN?

    1. It encrypts only email between two organizations
    2. It requires client software on each user laptop
    3. It protects access to a single web application
    4. It tunnels encrypted traffic between two gateways Correct answer.

    Explanation

    A site-to-site VPN builds an encrypted tunnel between two gateways, so hosts on either side communicate across a public network as if they were on a private link. Client-based software is used for remote-access VPNs instead.

  159. Question 159Security Fundamentals

    A switch port uses port security in restrict violation mode. A frame arrives with a source MAC address that is not in the secure address list. What is the result?

    1. The new MAC replaces the existing secure address
    2. The frame is dropped and a log entry is generated Correct answer.
    3. The port immediately enters err-disabled state
    4. All traffic is allowed but an alarm is raised

    Explanation

    In restrict mode the switch drops frames from the violating MAC address, increments the violation counter, and sends a syslog or SNMP notification. Shutdown mode err-disables the port, while protect mode drops silently without logging.

  160. Question 160Security Fundamentals

    What does DHCP snooping do on a Layer 2 switch?

    1. It assigns static IP addresses to hosts that request them
    2. It filters DHCP messages on untrusted ports Correct answer.
    3. It authenticates DHCP clients with 802.1X before leasing addresses
    4. It encrypts DHCP messages between clients and servers

    Explanation

    DHCP snooping treats ports facing clients as untrusted and drops server-type messages such as OFFER and ACK received on them, allowing them only on trusted ports. It also builds a binding table of client IP, MAC, VLAN, and port that other features reuse.

  161. Question 161Security Fundamentals

    Which attack does Dynamic ARP Inspection help prevent?

    1. A VLAN hopping attack using double tagging
    2. A CAM table overflow attack
    3. A DHCP starvation attack
    4. Gratuitous ARP used to poison hosts' ARP caches Correct answer.

    Explanation

    Dynamic ARP Inspection compares ARP packets against the DHCP snooping binding table and drops replies that do not match a valid IP-to-MAC binding. This blocks an attacker from answering ARP requests with a spoofed MAC and redirecting traffic.

  162. Question 162Security Fundamentals

    In an 802.1X deployment, which role does the LAN switch port normally perform?

    1. Authenticator Correct answer.
    2. Certificate authority
    3. Supplicant
    4. Authentication server

    Explanation

    The switch acts as the authenticator, relaying EAP messages between the client and the authentication server and blocking traffic until the port is authorized. The client is the supplicant and the RADIUS server is the authentication server.

  163. Question 163Security Fundamentals

    Which statement correctly distinguishes TACACS+ from RADIUS?

    1. TACACS+ encrypts the entire payload and separates AAA functions Correct answer.
    2. TACACS+ is an open standard supported by all vendors
    3. TACACS+ combines authentication and authorization in one exchange
    4. TACACS+ uses UDP and encrypts only the password

    Explanation

    TACACS+ runs over TCP port 49, encrypts the full packet body, and can perform authentication, authorization, and accounting as separate exchanges. RADIUS uses UDP, encrypts only the password field, combines authentication and authorization, and is an open standard.

  164. Question 164Security Fundamentals

    Which function is available in an extended ACL but not in a standard ACL?

    1. Using wildcard masks in each access list statement
    2. Applying the list to a vty line
    3. Filtering by source address only
    4. Filtering by protocol and port number Correct answer.

    Explanation

    Standard ACLs match only the source IPv4 address, while extended ACLs can match source and destination addresses, protocol, and TCP or UDP port numbers. Both types use wildcard masks and can be applied to interfaces or to vty lines.

  165. Question 165Security Fundamentals

    Which capability does GRE provide that IPsec alone does not?

    1. Authenticating each packet's header
    2. Providing data integrity through hashing
    3. Encrypting the payload of each packet
    4. Carrying multicast and non-IP protocols Correct answer.

    Explanation

    GRE is a tunneling protocol that can encapsulate multicast, broadcast, and non-IP traffic such as IPv6 or routing protocols. IPsec protects unicast IP traffic and provides encryption and integrity, but it does not tunnel non-IP payloads by itself.

  166. Question 166Security Fundamentals

    Why is asymmetric encryption used to exchange a symmetric key rather than to encrypt the entire data stream?

    1. Symmetric encryption provides authentication and asymmetric does not
    2. Asymmetric keys cannot be used to encrypt data
    3. Asymmetric encryption does not protect confidentiality
    4. Asymmetric algorithms are much slower for bulk data Correct answer.

    Explanation

    Symmetric ciphers such as AES process bulk data efficiently, while asymmetric algorithms require far more computation per byte. Asymmetric cryptography is therefore used to exchange or agree on a symmetric key, which then protects the actual traffic.

  167. Question 167Security Fundamentals

    Which property makes a hash function suitable for verifying integrity?

    1. Different inputs must not yield the same digest Correct answer.
    2. It must produce a variable-length output
    3. It must use the same key for signing and verification
    4. It must be reversible with the correct key

    Explanation

    A secure hash must be collision resistant so that two different inputs cannot produce the same digest, and it must be one-way so the original data cannot be recovered. Hashes also produce a fixed-length output for any input size.

  168. Question 168Security Fundamentals

    What is the key difference between an IPS and an IDS?

    1. An IPS relies solely on vendor signature updates
    2. An IPS drops traffic inline while an IDS only alerts Correct answer.
    3. An IDS inspects only encrypted traffic
    4. An IDS is deployed inline and can block traffic

    Explanation

    An intrusion prevention system sits inline in the traffic path and can drop or reset malicious packets, while an intrusion detection system receives a copy of traffic and only reports what it observes. Both can use signature-based and anomaly-based detection.

  169. Question 169Security Fundamentals

    Which IPsec component encrypts the packet payload to provide confidentiality?

    1. GRE
    2. IKE
    3. AH
    4. ESP Correct answer.

    Explanation

    Encapsulating Security Payload encrypts the payload and can also authenticate it, which is why ESP is used whenever confidentiality is required. Authentication Header provides integrity and origin authentication but does not encrypt.

  170. Question 170Security Fundamentals

    What is the primary role of a digital certificate in a PKI?

    1. It encrypts all traffic between client and server
    2. It stores the private key of the holder for backup
    3. It binds a public key to an identity Correct answer.
    4. It defines the cipher suite used for the TLS session

    Explanation

    A digital certificate is signed by a certificate authority and binds a public key to an identity, allowing a party to trust that the key belongs to the named entity. The holder keeps the matching private key secret and never publishes it.

  171. Question 171Security Fundamentals

    Which configuration change best mitigates VLAN hopping through double-tagged frames?

    1. Move the native VLAN to an unused VLAN Correct answer.
    2. Configure root guard on trunk ports
    3. Enable BPDU guard on all access ports
    4. Enable port security with one MAC per port

    Explanation

    Double tagging relies on the attacker's frame being accepted on the native VLAN of the first trunk, where the outer tag is stripped and the inner tag is forwarded. Changing the native VLAN on all trunks to an unused VLAN ID removes that path, and disabling auto-trunking on access ports closes the other variant.

  172. Question 172Security Fundamentals

    What is the purpose of Control Plane Policing on a router?

    1. To rate-limit traffic destined to the route processor Correct answer.
    2. To mark voice traffic with the EF DSCP value at the edge
    3. To filter traffic between VLANs on a multilayer switch
    4. To limit the bandwidth of user data on access ports

    Explanation

    Control Plane Policing applies a QoS policy to traffic destined for the device's CPU, rate-limiting protocols such as ICMP and SSH so that a flood cannot overwhelm the control plane. Data-plane policing and ACLs handle user traffic instead.

  173. Question 173Security Fundamentals

    Which IPsec phase negotiates the IKE security association that protects the later IPsec SA negotiation?

    1. Phase 2 in quick mode
    2. Phase 3 in tunnel mode
    3. Phase 1 in main or aggressive mode Correct answer.
    4. The data phase in transport mode

    Explanation

    Phase 1 establishes a secure channel, the IKE SA, using main mode or aggressive mode with a Diffie-Hellman exchange and peer authentication. Phase 2 then runs inside that protected channel in quick mode to negotiate the IPsec SAs.

  174. Question 174Security Fundamentals

    Which STP feature prevents a switch attached to a designated port from taking over as the root bridge?

    1. Loop guard
    2. Root guard Correct answer.
    3. BPDU filter
    4. BPDU guard

    Explanation

    Root guard is applied to designated ports and places the port in a root-inconsistent state if a superior BPDU arrives, keeping the existing root bridge in place. BPDU guard instead err-disables ports that should never receive BPDUs, such as access ports.

  175. Question 175Security Fundamentals

    Which feature drops frames whose source MAC and IP address do not match the DHCP snooping binding table?

    1. IP Source Guard Correct answer.
    2. Dynamic ARP Inspection
    3. Storm control
    4. Port security

    Explanation

    IP Source Guard uses the DHCP snooping binding table to build per-port filters that allow only the assigned source IP address, and with port security the assigned MAC address, dropping spoofed frames. Dynamic ARP Inspection validates ARP packets rather than all data frames.

  176. Question 176Security Fundamentals

    An attacker gains access to a billing server and alters the account balances stored in a customer table. Which element of the CIA triad has been violated?

    1. Confidentiality
    2. Availability
    3. Nonrepudiation
    4. Integrity Correct answer.

    Explanation

    Integrity means data is accurate and has not been modified by unauthorized parties, so unauthorized alteration of stored records is an integrity violation. Availability concerns timely and reliable access to resources, and confidentiality concerns preventing unauthorized disclosure. Nonrepudiation is a separate security service, not one of the three CIA elements.

  177. Question 177Security Fundamentals

    Which command stores the privileged EXEC password as a one-way hash rather than readable text in the configuration?

    1. username admin secret cisco123
    2. service password-encryption
    3. enable password cisco123
    4. enable secret cisco123 Correct answer.

    Explanation

    The enable secret command stores the privileged EXEC password as a one-way hash (MD5, SHA-256, or scrypt depending on platform), so the original value cannot be recovered from the configuration. The older enable password command leaves the value in clear text unless a reversible encoding is applied.

  178. Question 178Security Fundamentals

    An administrator must drop traffic from one host to one server on TCP port 443 while permitting all other traffic. Which ACL type and placement should be used?

    1. Extended ACL near the source Correct answer.
    2. Standard ACL near the source
    3. Extended ACL near the server
    4. Standard ACL near the server

    Explanation

    Only an extended ACL can match on source address, destination address, protocol, and port number, which is required to filter a single TCP port. Extended ACLs are best placed as close to the source as possible so unwanted traffic is discarded before it crosses the network.

  179. Question 179Security Fundamentals

    Users on a switch port begin receiving incorrect default gateway information, and a rogue device is answering address requests. Which feature should be enabled to stop this?

    1. Dynamic ARP Inspection
    2. DHCP snooping Correct answer.
    3. BPDU Guard
    4. Port security

    Explanation

    DHCP snooping marks ports as trusted or untrusted and drops DHCP server messages such as OFFER and ACK that arrive on untrusted ports, so only an approved server can hand out addresses. It also builds a binding table of legitimate client address assignments.

  180. Question 180Security Fundamentals

    A site-to-site VPN must hide the contents of packets between two routers and also verify that they were not changed in transit. Which IPsec protocol satisfies both requirements?

    1. IKE
    2. AH
    3. GRE
    4. ESP Correct answer.

    Explanation

    ESP encrypts the payload for confidentiality and also provides integrity and origin authentication through its authentication trailer. AH offers integrity and authentication but performs no encryption, so it cannot hide packet contents.

  181. Question 181Automation and Programmability

    Which outcome is a primary benefit of automating network configuration with scripts or tools rather than typing CLI commands on each device?

    1. Routing protocols are no longer needed anywhere in the network core.
    2. Devices no longer need any configuration to forward traffic correctly.
    3. Changes are applied consistently with fewer human errors. Correct answer.
    4. Physical cabling is no longer required between distribution and access.

    Explanation

    Automation applies one intended configuration definition to many devices, which removes repetitive manual steps and the typos that accompany them. It changes how configuration is generated and delivered, not whether configuration, cabling, or routing protocols are still needed.

  182. Question 182Automation and Programmability

    Which HTTP method does a REST client use to read a resource without modifying it?

    1. DELETE
    2. PUT
    3. POST
    4. GET Correct answer.

    Explanation

    In REST APIs the HTTP method expresses the operation, and GET is defined as a safe, read-only retrieval of a representation of the resource. POST creates, PUT replaces or creates, and DELETE removes.

  183. Question 183Automation and Programmability

    In JSON, which pair of characters delimits an object that holds key/value pairs?

    1. Parentheses ( )
    2. Square brackets [ ]
    3. Angle brackets < >
    4. Curly braces { } Correct answer.

    Explanation

    JSON defines two container types: objects delimited by curly braces and arrays delimited by square brackets. Parentheses and angle brackets are not part of JSON syntax.

  184. Question 184Automation and Programmability

    Which configuration management tool is agentless and connects to managed devices over SSH using YAML playbooks?

    1. Jenkins
    2. Chef
    3. Puppet
    4. Ansible Correct answer.

    Explanation

    Ansible runs from a control node and reaches managed hosts over SSH, so no agent software must be installed on the devices. Puppet and Chef normally depend on an agent installed on the managed node.

  185. Question 185Automation and Programmability

    Which component in a software-defined network holds the centralized logic that programs the forwarding behavior of devices?

    1. The SDN controller Correct answer.
    2. The SNMP trap receiver
    3. The syslog server
    4. The NTP server

    Explanation

    In an SDN architecture the controller is the centralized decision point: it learns topology, computes policy, and programs devices through southbound interfaces. Servers that collect logs, synchronize time, or receive traps are management services rather than control-plane controllers.

  186. Question 186Automation and Programmability

    Which HTTP status code indicates that a request completed successfully?

    1. 500
    2. 404
    3. 200 Correct answer.
    4. 301

    Explanation

    HTTP status codes are grouped by class: 2xx means success, 3xx redirection, 4xx client error, and 5xx server error. Code 200 (OK) is the standard response for a successful request.

  187. Question 187Automation and Programmability

    A REST client sends a request without credentials and receives HTTP status code 401. What does the response indicate?

    1. The server understood the request but refused to authorize the authenticated user.
    2. The request lacked valid authentication credentials. Correct answer.
    3. The server encountered an unexpected condition while processing the request.
    4. The server could not locate the requested resource.

    Explanation

    401 Unauthorized means the request was not accompanied by acceptable authentication credentials, so the client must authenticate and retry. 403 Forbidden is the code returned when the client is authenticated but not permitted to perform the action.

  188. Question 188Automation and Programmability

    An orchestration application needs to read topology and policy information from an SDN controller. Which interface does the application use?

    1. The southbound interface the controller uses toward the devices
    2. The northbound API the controller exposes to applications Correct answer.
    3. The CLI of each managed device
    4. The SNMP MIB of each managed device

    Explanation

    Northbound APIs are exposed by the controller for applications and orchestration tools that sit above it, while southbound interfaces carry instructions downward to the network devices. An application therefore talks northbound and never touches the devices directly.

  189. Question 189Automation and Programmability

    In a controller-based fabric that separates overlay from underlay, what does the overlay provide?

    1. It tunnels traffic between fabric devices over the physical underlay. Correct answer.
    2. It provides the physical link-state routing used between spine and leaf.
    3. It authenticates endpoints before they join the fabric.
    4. It defines the physical cabling and port numbering scheme.

    Explanation

    The underlay is the physical network with its addressing and routing, while the overlay is a logical network built as tunnels on top of it, commonly using VXLAN. The overlay gives segmentation and endpoint mobility independent of the physical topology.

  190. Question 190Automation and Programmability

    Which statement describes how control-plane and data-plane functions are arranged in a controller-based SDN architecture?

    1. The data plane computes routes and passes them up to the control plane.
    2. An administrator manually types forwarding entries into each device.
    3. A controller computes forwarding information and programs the devices. Correct answer.
    4. Every device computes its own topology view and forwards packets from that view.

    Explanation

    SDN separates the control plane, which decides how traffic should be forwarded, from the data plane, which performs the forwarding. The controller makes those decisions centrally and installs them on the devices instead of letting each device decide on its own.

  191. Question 191Automation and Programmability

    Which statement describes the way Puppet typically applies configuration to a managed node?

    1. A network engineer pastes configuration into a terminal session.
    2. A local client executes cookbooks and recipes from a run list.
    3. An agent on the node pulls a compiled catalog from the server. Correct answer.
    4. An agentless control node pushes YAML playbooks over SSH.

    Explanation

    Puppet uses a declarative manifest that the Puppet server compiles into a catalog, which the agent on the managed node retrieves and enforces on a periodic run. Cookbooks and recipes belong to Chef, and agentless SSH playbooks belong to Ansible.

  192. Question 192Automation and Programmability

    A configuration management tool is described as idempotent. What does that property mean?

    1. It records every change in a version-control repository.
    2. It requires an administrator to approve each change before it runs.
    3. Repeated runs of the same configuration reach the same end state. Correct answer.
    4. It applies changes only during an approved maintenance window.

    Explanation

    Idempotency means a task inspects the current state and makes only the changes needed to reach the declared state, so repeated runs converge on the same result. That property is what makes these tools safe to schedule regularly.

  193. Question 193Automation and Programmability

    In the JSON document {"device": "switch1", "vlans": [10, 20, 30], "enabled": true}, which value is an array?

    1. "switch1"
    2. true
    3. [10, 20, 30] Correct answer.
    4. "vlans"

    Explanation

    In JSON, square brackets denote an array, an ordered list of values, while a quoted string and the literals true and false are scalar values. A key simply names a value and is not itself a container.

  194. Question 194Automation and Programmability

    What does it mean to say that a REST API is stateless?

    1. The API does not use HTTP headers.
    2. Each request carries everything needed to process it. Correct answer.
    3. The API is not allowed to store data in a database.
    4. The API accepts only one client connection at a time.

    Explanation

    In REST the server keeps no per-client session context between calls, so the client must send whatever is needed, such as credentials and resource identifiers, with every request. This is what allows any server behind a load balancer to handle the request.

  195. Question 195Automation and Programmability

    Which capability does Cisco DNA Center provide for a campus network?

    1. It encrypts all traffic between access switches and the WAN edge.
    2. It replaces OSPF and EIGRP with a proprietary DNA Center routing protocol.
    3. It assigns IPv4 addresses to endpoints in place of a DHCP server.
    4. It centrally automates device configuration and monitors network health. Correct answer.

    Explanation

    DNA Center is a controller-based management platform that offers design, policy, provisioning, and assurance functions through a GUI and northbound APIs. It works with the standard protocols already running on the devices rather than replacing them.

  196. Question 196Automation and Programmability

    Which statement correctly describes pull-based configuration management?

    1. Pull-based tools apply configuration only when a device reboots.
    2. The device agent pulls configuration from a server on a schedule. Correct answer.
    3. Pull-based tools cannot be used to manage network devices.
    4. Pull-based tools require no software on the managed device.

    Explanation

    In the pull model an agent on the managed node contacts the configuration server at intervals, retrieves the configuration intended for that node, and enforces it. In the push model the control node initiates the connection, often over SSH with no agent installed.

  197. Question 197Automation and Programmability

    In a Cisco SD-Access fabric, which node type connects the fabric to networks outside the fabric?

    1. The border node Correct answer.
    2. The control plane node
    3. The intermediate node
    4. The edge node

    Explanation

    Border nodes sit at the fabric boundary and hand traffic off to external networks such as the WAN, data center, or internet. Edge nodes attach wired and wireless endpoints to the fabric, while control plane nodes hold the endpoint-to-location mapping database.

  198. Question 198Automation and Programmability

    A developer sends a POST request to create a VLAN and receives HTTP status code 201 with a Location header. What does this response mean?

    1. The request succeeded but the server made no change to its state.
    2. The resource was created and the Location header gives its URI. Correct answer.
    3. The server redirected the request to a different endpoint.
    4. The request failed because a VLAN with that identifier already exists.

    Explanation

    201 Created is the success code for a request that results in a new resource, and the Location header carries the URI of that new resource. A conflicting duplicate would return 409, and a successful no-op is normally reported with 200 or 204.

  199. Question 199Automation and Programmability

    In a controller-based network, what is the purpose of the southbound interface?

    1. It converts CLI commands into SNMP traps for the management server.
    2. It lets external business applications read the controller's topology database.
    3. It lets the controller program the configuration and forwarding of devices. Correct answer.
    4. It synchronizes the controller's clock with the managed devices.

    Explanation

    Southbound interfaces and protocols, such as NETCONF, RESTCONF, OpenFlow, or vendor APIs, carry the controller's instructions down to the network devices. Northbound interfaces serve the applications that sit above the controller.

  200. Question 200Automation and Programmability

    Which data-serialization format organizes values with indentation and colons rather than curly braces and square brackets?

    1. CSV
    2. YAML Correct answer.
    3. JSON
    4. XML

    Explanation

    YAML uses indentation to express hierarchy and colons to separate keys from values, which makes it easier for humans to read. JSON uses braces and brackets, XML uses tags, and CSV uses delimiters between flat fields.

CCNA flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Broadcast domain
A network segment where all devices receive each other's broadcast frames; routers and VLANs do not forward broadcasts between them unless explicitly configured.
TCP three-way handshake
Connection setup using SYN, SYN-ACK, and ACK segments; TCP uses it to synchronize initial sequence numbers before any application data is sent.
APIPA address
IPv4 address a host self-assigns when DHCP fails; the host can communicate only on the local link and cannot reach remote networks.
Usable hosts per subnet
Subtract 2 from 2 raised to the number of host bits: a /26 has 6 host bits, so 64 minus 2 equals 62 usable addresses.
Address Resolution Protocol
Protocol that maps a known IPv4 address to a MAC address by broadcasting a request inside the local subnet, then caching the reply briefly.
IPv6 address format
128 bits written as eight groups of four hexadecimal digits; a double colon may compress exactly one run of consecutive all-zero groups.
802.1Q tag
Adds a 4-byte field to Ethernet frames carrying a 12-bit VLAN identifier; the native VLAN is the only traffic forwarded untagged across the trunk.
STP root bridge election
The switch with the lowest bridge ID wins, comparing the 2-byte priority first, then the MAC address; default priority is 32768 and is added to the VLAN ID.
PortFast and BPDU Guard
PortFast skips listening and learning so an access port forwards immediately; BPDU Guard err-disables the port if a BPDU arrives, preventing loops.
EtherChannel requirements
Bundled member links must match speed, duplex, and allowed VLANs; LACP, defined in 802.3ad, is the standards-based negotiation protocol; PAgP is Cisco proprietary.
CAPWAP tunnels
Access points and wireless controllers carry management and data traffic over UDP 5246 and 5247; the AP can find the controller by broadcast, DHCP option 43, or DNS.
Longest prefix match
A router first prefers the route with the most specific mask; administrative distance and metric break ties only between routes for the same prefix length.
Administrative distance values
Connected routes are 0, static routes 1, EIGRP 90, OSPF 110, and RIP 120; when the same prefix is learned from several sources the lowest value is installed.
OSPF timers on broadcast
OSPF sends hello packets every 10 seconds on broadcast and point-to-point networks and declares a neighbor dead after 40 seconds; both values must match.
OSPF DR election
The interface with the highest OSPF priority becomes designated router, default priority 1; ties are broken by highest router ID, and priority 0 can never be DR.
Floating static route
A static route given an administrative distance higher than the dynamic protocol so it stays out of the table until the primary route fails.
Router-on-a-stick
One physical router interface divided into 802.1Q subinterfaces, each assigned an IP address and acting as the default gateway for its VLAN.
DHCP DORA process
Four messages, Discover, Offer, Request, and Acknowledge, lease an IPv4 address; the client broadcasts from UDP 68 and the server replies from UDP 67.
Syslog severity levels
Eight levels numbered 0 through 7: emergency, alert, critical, error, warning, notice, informational, debug; lower numbers are more severe and debug is 7.
NAT overload
Translates many inside local addresses to a single inside global address, telling the flows apart by unique source port numbers; also called port address translation.
NTP stratum
Stratum 1 servers synchronize directly to an authoritative reference clock; each level away adds one, values run 0 to 15, and 16 means unsynchronized.
SNMP ports
Managers poll agents on UDP 161 and agents send unsolicited traps to UDP 162; SNMPv3 added authentication and encryption that earlier versions lack.
Standard versus extended ACL
Standard ACLs numbered 1-99 filter only the source address and are placed near the destination; extended ACLs 100-199 filter protocol, source, destination, and port near the source.
ACL wildcard mask
A zero bit means the corresponding address bit must match, 255 means ignore it; it is the inverse of a subnet mask, so /24 becomes 0.0.0.255.
Port security violation modes
Protect silently drops frames from unknown MAC addresses; restrict drops and logs them; shutdown places the port in err-disabled state until an administrator re-enables it.
TACACS+ versus RADIUS
TACACS+ runs over TCP 49 and encrypts the whole packet body; RADIUS runs over UDP 1812 and 1813 and encrypts only the password field.
DHCP snooping
Trusts uplink ports, treats access ports as untrusted, rate-limits DHCP messages there, and builds a bindings table of MAC, IP, VLAN, and port.
Northbound versus southbound APIs
Northbound APIs expose the controller to applications and automation scripts, while southbound APIs push configuration and read state from the network devices themselves.
REST HTTP verbs
GET reads, POST creates, PUT replaces, PATCH partially updates, and DELETE removes a resource; each REST request is stateless and carries all needed information.
Ansible
An agentless configuration management tool that connects to devices over SSH and applies declarative playbooks written in YAML, so no software runs on the managed node.
NETCONF
Uses XML-encoded remote procedure calls over an SSH session on TCP 830 to read and edit the configuration datastores of network devices.
SDN planes
Software-defined networking centralizes the control plane in a controller and leaves the data plane on the devices, which forward traffic using tables the controller builds.

CCNA study guide

Network Fundamentals

Models and encapsulation

Move fluently between the OSI seven-layer model and the four-layer TCP/IP model. The transport layer adds TCP or UDP headers (segments/datagrams), the internet layer adds IP headers (packets), and the data link layer wraps everything in an Ethernet frame with MAC addresses and an FCS trailer. Traps: questions asking which layer a device works at (hub/repeater = L1, switch/bridge = L2, router = L3), and the direction of encapsulation (top-down on send, bottom-up on receive).

Addressing

IPv4 essentials: private ranges 10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16; loopback 127.0.0.0/8; APIPA 169.254.0.0/16. IPv6 essentials: global unicast 2000::/3, link-local FE80::/10, unique local FC00::/7, multicast FF00::/8, loopback ::1. IPv6 has no broadcast, so any answer offering an IPv6 broadcast address is wrong by definition. SLAAC, EUI-64, and anycast are common distractors.

Switching and transport

Switches learn source MACs and flood unknown unicast, broadcast, and multicast frames. Count broadcast domains per VLAN or routed interface, not per port. Know the three-way handshake and well-known ports: 20/21 FTP, 22 SSH, 23 Telnet, 25 SMTP, 53 DNS, 67/68 DHCP, 69 TFTP, 80 HTTP, 443 HTTPS.

Rule of thumb

For any prefix, host bits n = 32 − prefix, addresses per subnet = 2^n, usable hosts = 2^n − 2. A /26 leaves 6 host bits: 64 addresses, 62 usable, boundaries at .0, .64, .128, .192 (256 − 64 = 64).

Network Access

VLANs and trunks

Access ports carry one VLAN; trunk ports carry many using 802.1Q tags. The native VLAN is sent untagged, so both ends must agree - a native VLAN mismatch shows up in CDP/LLDP output and is a classic exam scenario. The allowed VLAN list defaults to all VLANs. Inter-VLAN routing requires a Layer 3 interface: router-on-a-stick subinterfaces or switch SVIs with ip routing enabled.

Spanning Tree

802.1D and 802.1w elect one root bridge using the lowest bridge ID (priority, then MAC; default priority 32768). Root path cost decides which ports forward, then lowest sender bridge ID, then lowest port ID. Legacy states: blocking, listening (15 s), learning (15 s), forwarding. RSTP collapses these to discarding, learning, forwarding. All ports on the root bridge are designated and forwarding. Know PortFast (access ports only) and BPDU guard (err-disables a port that receives a BPDU).

EtherChannel

Bundling makes STP see one logical link. Requirements: matching speed/duplex, allowed and native VLANs, and switchport mode. LACP uses active/passive, PAgP uses desirable/auto, and static on works with neither. Mismatches such as on versus passive fail silently.

Wireless

Separate SSID (network name), BSSID (radio MAC), and BSS (one AP's cell). A WLC manages lightweight APs over CAPWAP (UDP 5246/5247). AP modes include local, FlexConnect, monitor, sniffer, SE-connect, and rogue detector.

Rule of thumb

When a trunk misbehaves, verify both ends first: same native VLAN, same allowed list, same encapsulation. Data VLANs still pass during a native VLAN mismatch - the warning appears in CDP, not as a link failure.

IP Connectivity

Reading the routing table

Each entry has a prefix, next hop or exit interface, administrative distance (AD), and metric. The router forwards on longest prefix match first; AD and metric only break ties between identical prefixes. Trap: a /24 learned through OSPF beats a /16 static route for any destination inside the /24 - longest match outranks trustworthiness.

Administrative distance

Connected 0, static 1, eBGP 20, EIGRP 90, OSPF 110, RIP 120, iBGP 200. A floating static route sets a higher AD than the dynamic protocol so it installs only when the primary disappears.

OSPFv2 single area

Neighbors must match area ID, subnet/mask, timers, and authentication; an MTU mismatch can stall database exchange at ExStart. On broadcast networks the DR/BDR uses highest priority (default 1), then highest router ID (highest loopback, else highest active interface IP). Election is not preemptive - a new router with better priority waits for an OSPF restart. Cost = reference bandwidth (100 Mbps by default) ÷ interface bandwidth. Passive interfaces suppress hellos without stopping advertisement; default-information originate injects a default route.

First-hop redundancy

HSRP (Cisco, active/standby, virtual MAC 0000.0c07.acXX, preemption off by default), VRRP (standard, master/backup), GLBP (load sharing).

Rule of thumb

Asked why a route is not installed, compare AD first, metric second. Asked which path a packet takes, run longest prefix match before anything else.

IP Services

DHCP and DNS

DORA: Discover (broadcast), Offer, Request (broadcast), Acknowledge. When the server sits on another subnet, the client-facing interface needs ip helper-address, which converts the broadcast into unicast to the server. Trap: the helper goes on the router or SVI nearest the client, not on the server's side.

NAT

Static NAT is 1:1, dynamic NAT uses a pool, PAT (overload) is many-to-one using ports. Inside local is the real internal address before translation; inside global is what the outside world sees. Most failures trace to a missing ip nat inside/outside on an interface or an ACL that does not match.

NTP, syslog, SNMP

NTP stratum 1–15 is valid; 16 means unsynchronized, which is the Cisco default until a server answers. Syslog severity descends in number as it rises in urgency: 0 emergencies, 1 alerts, 2 critical, 3 errors, 4 warnings, 5 notifications, 6 informational, 7 debugging. logging trap 6 sends levels 0–6, not level 6 alone. SNMPv3 adds authentication and encryption; traps are unacknowledged, informs get a reply.

QoS and management access

Know marking (DSCP at Layer 3, CoS at Layer 2), queuing (priority, weighted fair), and the difference between shaping (buffer) and policing (drop). SSH requires a hostname, domain name, and generated RSA keys before it works - a favourite "first missing step" question. TFTP is UDP 69 with no authentication.

Rule of thumb

For NAT troubleshooting, verify in order: inside/outside roles, ACL match, then show ip nat translations. For SSH, verify hostname, domain name, crypto key, then vty transport input ssh.

Security Fundamentals

Vocabulary and program elements

Separate vulnerability (a weakness), exploit (the method that abuses it), and threat (a potential actor or event). Mitigations map to confidentiality, integrity, and availability. Program questions test user awareness training, physical access control, and incident response - they are not configuration tasks.

Hardening and AAA

Minimum baseline: enable secret rather than enable password, service password-encryption, a login banner, exec-timeout, SSH instead of Telnet, disabled unused services, and unused ports shut or parked in an unused VLAN. AAA means authentication, authorization, accounting. In 802.1X the supplicant is the client, the authenticator is the switch, and the authentication server is RADIUS - trap: the switch is never the authentication server.

Layer 2 protections

Port security limits MACs per port. Violation modes: protect (drop, no log), restrict (drop, log, increment counter), shutdown (err-disable, the default). Sticky learning writes learned MACs into the running config. DHCP snooping trusts only ports toward the legitimate server; untrusted ports drop server-sourced offers. Dynamic ARP Inspection uses the snooping binding table to drop spoofed ARP replies.

ACLs

Standard ACLs (1–99, 1300–1999) match source only and belong near the destination. Extended ACLs (100–199, 2000–2699) match protocol, source, destination, and ports, and belong near the source. Every ACL ends with an implicit deny any. Wildcard masks invert the subnet mask.

Rule of thumb

For /27 (255.255.255.224), wildcard = 255 − 224 = 0.0.0.31. Apply the same subtraction to every octet to build any wildcard.

Automation and Programmability

Traditional versus controller-based

Traditional networking configures each device by CLI and runs distributed control planes. Controller-based networking centralises the control plane: Catalyst Center (formerly DNA Center) for campus fabrics, SD-WAN Manager for WAN. Northbound APIs face the application or operator and are typically REST/JSON; southbound APIs face the devices (NETCONF, RESTCONF, CLI, SNMP, OpenFlow). Trap: northbound points toward the application, not toward the hardware.

Data formats and REST APIs

JSON uses key/value pairs in curly braces and arrays in square brackets; XML uses nested tags. Map CRUD to HTTP verbs: POST create, GET read, PUT/PATCH update, DELETE remove. GET is safe and idempotent; POST is neither. Status codes to memorise: 200 OK, 201 created, 400 bad request, 401 unauthorized, 404 not found.

Configuration management and CI/CD

Ansible is agentless over SSH. Puppet and Chef use agents with manifests and cookbooks/recipes respectively. CI/CD pipelines test configuration then deploy it; infrastructure as code keeps configuration versioned like software.

Cloud and virtualization

IaaS: you manage the OS and upward. PaaS: you manage only the application. SaaS: you manage nothing. Type 1 hypervisors run bare metal (ESXi); Type 2 are hosted (VirtualBox). Containers share the host kernel and are lighter than virtual machines.

Rule of thumb

If a question asks which tool needs no software installed on the managed device, answer Ansible. If it asks which API direction a Python script uses to reach a controller, answer northbound.

CCNA cheat sheet

Quick reference

Network Fundamentals

  • OSI layers top to bottom: Application (7), Presentation (6), Session (5), Transport (4), Network (3), Data Link (2), Physical (1).

  • TCP is connection-oriented and uses a three-way handshake (SYN, SYN-ACK, ACK) with retransmission; UDP is connectionless with no retransmission.

  • Private IPv4 ranges: 10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16. An address in 169.254.0.0/16 means DHCP failed.

  • Usable hosts per subnet = 2^h - 2, where h is the number of host bits; a /24 has 8 host bits, so 254 usable addresses.

  • Mask values by prefix: /25 = 255.255.255.128, /26 = .192, /27 = .224, /28 = .240, /29 = .248, /30 = .252.

  • First octet ranges: A 1-126, B 128-191, C 192-223, D 224-239 multicast, E 240-255 experimental; 127.0.0.0/8 is loopback.

  • Ethernet UTP runs 100 m for 100BASE-TX and 1000BASE-T; 1000BASE-LX over multimode fiber reaches about 550 m.

  • Straight-through cable connects unlike devices (switch to router, switch to PC); crossover connects like devices; auto-MDIX removes the requirement.

  • Ethernet default MTU is 1500 bytes; TCP uses a sliding window plus MSS to limit how much unacknowledged data is in flight.

Quick reference

Network Access

  • VLANs divide a switch into separate broadcast domains; all ports default to VLAN 1, and inter-VLAN traffic needs a Layer 3 device.

  • An access port carries one VLAN untagged; a trunk carries many VLANs and tags every frame except the native VLAN with 802.1Q.

  • Trunk configuration commands: switchport mode trunk, switchport trunk allowed vlan , switchport trunk native vlan .

  • DTP modes are access, trunk, dynamic auto (passive), dynamic desirable (active), and nonegotiate; mismatched modes prevent a trunk forming.

  • STP elects one root bridge by lowest bridge ID (priority first, then MAC); default priority is 32768 and port costs accumulate toward the root.

  • 802.1D port states: blocking, listening (15 s), learning (15 s), forwarding, disabled; RSTP collapses these to discarding, learning, forwarding.

  • PortFast skips listening and learning on access ports; BPDU Guard err-disables a PortFast port that receives a BPDU; Root Guard rejects superior BPDUs.

  • EtherChannel members must match speed, duplex, and VLANs; LACP (802.3ad) is standards-based, PAgP is Cisco proprietary, and static on-mode uses no negotiation.

  • CAPWAP tunnels use UDP 5246 for control and UDP 5247 for data; AP modes include local, FlexConnect, monitor, sniffer, and rogue detector.

Quick reference

IP Connectivity

  • Route selection order: longest prefix match first, then lowest administrative distance, then lowest metric.

  • Default administrative distances: connected 0, static 1, EIGRP 90, OSPF 110, RIP 120.

  • Static route syntax: ip route [distance]; a static with a distance above the dynamic route is a floating static.

  • OSPF cost = reference bandwidth (default 100 Mbps) divided by interface bandwidth, so a 10 Mbps link costs 10 and a 100 Mbps link costs 1.

  • OSPF neighbor states in order: Down, Init, 2-Way, ExStart, Exchange, Loading, Full; mismatched area, subnet, or timers prevents reaching Full.

  • OSPF DR and BDR are elected by highest interface priority (default 1), then highest router ID; priority 0 excludes an interface from the election.

  • EIGRP uses a composite metric of bandwidth and delay by default; a feasible successor is a loop-free backup route held in the topology table.

  • FHRP options: HSRP (Cisco, virtual MAC 0000.0c07.acXX), VRRP (standards-based, MAC 0000.5e00.01XX), GLBP (Cisco, load balancing).

  • Router-on-a-stick: the physical interface has no IP, and subinterfaces use encapsulation dot1q plus an IP that serves as that VLAN's gateway.

Quick reference

IP Services

  • DHCP uses DORA (Discover, Offer, Request, Acknowledge); server UDP 67, client UDP 68; ip helper-address forwards requests across subnets.

  • NAT terms: inside local (private host address), inside global (public translated address), outside local, outside global; PAT shares one address using ports.

  • NTP uses UDP 123; stratum 1 syncs to a reference clock, each hop adds one, valid range is 0-15, and 16 means unsynchronized.

  • Syslog severity: 0 emergency, 1 alert, 2 critical, 3 error, 4 warning, 5 notice, 6 informational, 7 debug; lower numbers are more severe.

  • SNMP manager polls agents on UDP 161 and traps go to UDP 162; SNMPv3 adds authentication (MD5/SHA) and encryption (DES/AES).

  • HSRP is Cisco proprietary with default priority 100 and preemption disabled; VRRP is standards-based with priority 100 and preemption enabled.

  • QoS marking: DSCP uses the top 6 bits of the ToS byte (0-63); EF 46 is for voice, AF41 for video, and CS0 is default best effort.

  • Telnet uses TCP 23 in clear text while SSH uses TCP 22 encrypted; DNS queries use UDP 53 and zone transfers use TCP 53.

  • CDP is Cisco proprietary and enabled by default; LLDP is IEEE 802.1AB and disabled by default; both operate at Layer 2.

Quick reference

Security Fundamentals

  • AAA components: authentication (who you are), authorization (what you may do), accounting (what you did); TACACS+ uses TCP 49, RADIUS uses UDP 1812/1813.

  • Standard ACLs (1-99, 1300-1999) match source only and are placed near the destination; extended ACLs (100-199, 2000-2699) match protocol, source, destination, and port and go near the source.

  • Every ACL ends with an implicit deny any; in a wildcard, 0 means match the bit and 255 means ignore it (the inverse of the subnet mask).

  • Port security learns MAC addresses and violation modes are protect (drop), restrict (drop plus log and counter), and shutdown (err-disable).

  • DHCP snooping marks uplinks trusted, rate-limits DHCP on untrusted ports, and builds a MAC/IP/VLAN/port binding table used by Dynamic ARP Inspection.

  • 802.1X roles: supplicant (client), authenticator (switch), authentication server (RADIUS); EAP frames travel in EAPoL between client and switch.

  • service password-encryption uses reversible type 7; enable secret uses type 5 MD5 or stronger type 8/9 hashes.

  • IPsec: AH (protocol 51) authenticates but does not encrypt; ESP (protocol 50) provides confidentiality; IKE negotiates SAs over UDP 500.

  • Router SSH requires a hostname and domain name, crypto key generate rsa with a 2048-bit modulus, and transport input ssh on the vty lines.

Quick reference

Automation and Programmability

  • SDN separates the control plane (centralized controller) from the data plane (devices forwarding traffic); the controller programs forwarding tables.

  • Northbound APIs face applications (typically REST with JSON); southbound APIs face devices (OpenFlow, NETCONF, RESTCONF, CLI).

  • Cisco SDN platforms: DNA Center for campus, ACI for data center, SD-WAN (vManage) for WAN; each is an intent-based controller.

  • REST verbs: GET reads, POST creates, PUT replaces, PATCH partially updates, DELETE removes; 2xx is success, 4xx is client error, 5xx is server error.

  • Data formats: JSON (key-value pairs in braces, native to REST), XML (tags, used by NETCONF), YAML (indentation, used by Ansible).

  • Ansible is agentless over SSH using YAML playbooks; Puppet and Chef use agents; Terraform is declarative and uses HCL.

  • NETCONF runs XML over SSH on TCP 830; RESTCONF runs over HTTP/HTTPS with JSON or XML; both use YANG data models.

  • Imperative tooling lists each step to run; declarative tooling states the desired end state, and idempotent tools converge to the same result when rerun.

  • Model-driven telemetry streams data to a collector instead of polling with SNMP, giving near-real-time monitoring.

CCNA key terms

OSI model

A seven-layer reference framework that describes how data moves from an application on one host to an application on another, separating functions such as addressing, routing, and reliable delivery into named layers.

Related: TCP, UDP
TCP

A connection-oriented transport protocol that uses a three-way handshake, sequence numbers, and acknowledgments to deliver a reliable, ordered byte stream between applications.

Related: UDP, OSI model
UDP

A connectionless transport protocol that sends datagrams without handshakes, acknowledgments, or retransmission, making it fast and low-overhead but unreliable.

Related: TCP, DNS
Subnet mask

A 32-bit value of contiguous ones followed by zeros that tells a device which bits of an IPv4 address identify the network and which bits identify the host.

Related: CIDR notation, Default gateway
CIDR notation

A shorthand way to write an IPv4 or IPv6 prefix, where the address is followed by a slash and a number showing how many leading bits are the network portion.

Related: Subnet mask, Routing table
MAC address

A 48-bit hardware address assigned to a network interface, written as six hexadecimal bytes, used by Ethernet to deliver frames to a device on the local segment.

Related: ARP, VLAN
VLAN

A logically separate Layer 2 broadcast domain created on switches, letting devices on different ports behave as if they were on separate physical networks.

Related: Access port, Trunk port
Access port

A switch port configured for a single VLAN that connects to an end device and sends and receives untagged Ethernet frames.

Related: Trunk port, VLAN
Trunk port

A switch port that carries traffic for multiple VLANs between switches or to a router, tagging frames with 802.1Q headers so VLAN membership is preserved.

Related: Access port, VLAN
Spanning Tree Protocol

A Layer 2 protocol that builds a loop-free topology by electing a root bridge, choosing root and designated ports, and blocking redundant links.

Related: EtherChannel, VLAN
EtherChannel

A configuration that bundles several physical switch links into one logical link, increasing bandwidth and providing redundancy while spanning tree sees a single port.

Related: Spanning Tree Protocol, Trunk port
SSID

The name that identifies a wireless network, carried in beacon frames so that client devices can discover and associate with the correct WLAN.

Related: Wireless LAN controller, WPA2
Wireless LAN controller

A device or software that centrally manages many access points, handling configuration, roaming, and wireless security policy in one place instead of per access point.

Related: SSID, WPA2
Default gateway

The IP address of a router interface on the local subnet that hosts send packets to when the destination lies outside their own network.

Related: Routing table, Subnet mask
Routing table

A list kept by a router showing known destination networks, the next hop or exit interface for each, and the metric or source of the route.

Related: Administrative distance, Static route
Administrative distance

A number from 0 to 255 that rates how trustworthy a route source is; lower values win when different protocols offer a route to the same network.

Related: Routing table, OSPF
Static route

A route manually entered by an administrator that tells the router where to send traffic for a specific destination, and that does not adapt automatically to topology changes.

Related: Routing table, OSPF
OSPF

An open-standard link-state interior routing protocol that floods link information, builds a common topology database, and runs the shortest-path-first algorithm to select routes.

Related: Administrative distance, Routing table
ARP

A protocol that resolves a known IPv4 address to an unknown MAC address on the local link by broadcasting a request and caching the unicast reply.

Related: MAC address, Default gateway
DHCP

A protocol that automatically supplies hosts with an IP address, subnet mask, default gateway, and DNS servers through a discover, offer, request, and acknowledge exchange.

Related: DNS, DHCP snooping
DNS

A hierarchical naming system that translates human-readable domain names into IP addresses so applications can reach servers without hard-coded addresses.

Related: DHCP, UDP
NAT

A technique that rewrites IP addresses in packet headers as traffic crosses a router, commonly letting many private hosts share a few public addresses.

Related: Routing table, ACL
NTP

A protocol that synchronizes clocks across devices to a common time source, keeping log timestamps consistent and supporting certificate and authentication validity checks.

Related: Syslog, SNMP
SNMP

A management protocol in which an agent on a device reports status and sends traps to a central manager, using a tree of object identifiers.

Related: Syslog, NTP
Syslog

A standard for sending event messages from network devices to a logging server, with each message carrying a facility and a severity level.

Related: SNMP, NTP
TFTP

A simple, connectionless file transfer protocol over UDP that network devices use to save and load configurations and operating system images.

Related: SSH, Syslog
SSH

An encrypted protocol for remote command-line access to network devices, replacing insecure Telnet by protecting credentials and session data in transit.

Related: AAA, ACL
ACL

An ordered list of permit and deny statements applied to an interface or line that matches traffic by addresses, ports, or protocol to filter packets.

Related: NAT, SSH
AAA

A framework that separates authentication of users, authorization of what they may do, and accounting of what they did, often using a central server such as RADIUS or TACACS+.

Related: SSH, ACL
Port security

A switch feature that limits which and how many MAC addresses may use a port, and can shut down or restrict the port when a violation occurs.

Related: DHCP snooping, MAC address
DHCP snooping

A switch feature that marks ports as trusted or untrusted and drops DHCP server messages arriving on untrusted ports, preventing rogue servers and address spoofing.

Related: DHCP, Port security
WPA2

A wireless security standard using AES-CCMP encryption with either a pre-shared key or 802.1X authentication to protect traffic sent over the air.

Related: SSID, AAA
REST API

An interface style where clients use HTTP methods such as GET, POST, PUT, and DELETE on resource URLs, usually exchanging data in JSON or XML.

Related: JSON, Software-defined networking
JSON

A lightweight text format for structured data using objects, arrays, strings, numbers, booleans, and null, widely used by APIs and automation tools.

Related: REST API, Ansible
Ansible

An agentless automation tool that pushes configuration to network devices over SSH using plain-text playbooks written in YAML.

Related: SSH, JSON
Software-defined networking

An architecture that separates the control plane, which decides where traffic goes, from the data plane, which forwards it, letting a central controller program devices.

Related: REST API, Wireless LAN controller

CCNA study plan

8 weeks · About 6 hours per week

Week 1

Network Fundamentals

  • Convert between binary, decimal, and hexadecimal for IPv4 addresses and masks without a calculator

  • Calculate network ID, broadcast address, and usable host range for any /8-/30 prefix

  • Map each OSI layer to its PDU, devices, and protocols, and describe encapsulation/decapsulation order

  • Compare router, switch, hub, firewall, and AP by collision/broadcast domain behavior

  • Distinguish TCP vs UDP behavior and identify the well-known port numbers for common services

Your checkpoint

Score 90% or better on a closed-book, timed 25-question subnetting and fundamentals quiz, with a written error log of every missed item

Week 2

Network Fundamentals & IP Connectivity

  • Interpret a routing table entry by entry (prefix, mask, next hop, AD, metric, outgoing interface)

  • Configure IPv4 static, default, and floating static routes on a multi-router topology

  • Explain how longest-prefix match and administrative distance resolve competing routes

  • Describe the IPv4 header fields and identify where fragmentation and TTL decrement occur

  • Compare IPv4 and IPv6 addressing, including address types and neighbor discovery basics

Your checkpoint

Build a 4-router static-routing lab in a simulator with redundant paths; all end-to-end pings succeed and both a primary and floating static failover are demonstrated with captured routing tables

Week 3

IP Connectivity

  • Configure single-area OSPFv2 (network statements, passive interfaces, router ID) on three routers

  • Verify OSPF neighbor adjacencies and states using show commands and troubleshoot a deliberate mismatch

  • Tune OSPF cost and explain how DR/BDR election is determined

  • Configure and verify a first-hop redundancy protocol (HSRP or VRRP) for a default gateway

  • Differentiate interior gateway routing concepts: distance vector vs link state, and classful vs classless behavior

Your checkpoint

Deliver a 3-router OSPF topology with full adjacency, an intentional failure scenario you diagnose and fix, and a one-page write-up of show ip ospf neighbor and show ip route output

Week 4

Network Access

  • Configure VLANs, access ports, and 802.1Q trunk links, and verify with show vlan and show interfaces trunk

  • Configure inter-VLAN routing using both router-on-a-stick and an SVI on a multilayer switch

  • Predict and verify spanning-tree root election, port roles, and states after a topology change

  • Configure EtherChannel with LACP and confirm a bundled link with show etherchannel summary

  • Explain native VLAN behavior and troubleshoot a native VLAN mismatch

Your checkpoint

Build a 3-switch Layer 2 lab with VLANs, trunking, EtherChannel, and inter-VLAN routing; every VLAN reaches every other VLAN and STP root placement matches your written prediction

Week 5

Network Access & Security Fundamentals

  • Describe wireless fundamentals: 802.11 standards, channels, bands, and the roles of WLC and AP in a CAPWAP architecture

  • Configure switch port security (maximum MACs, violation modes) and verify with show port-security

  • Configure DHCP snooping and dynamic ARP inspection, and explain how they stop rogue-server and spoofing attacks

  • Configure standard and extended ACLs and place them where they actually filter the intended traffic

  • Harden device access: local AAA concepts, SSH-only VTY, enable secret, service password-encryption, and unused-port shutdown

  • Identify common threat categories and the purpose of VPN, IPS, and endpoint security controls

Your checkpoint

Harden a small lab network with port security, DHCP snooping, DAI, and an extended ACL; produce a verification transcript showing permitted traffic succeeds and blocked traffic fails

Week 6

Security Fundamentals & IP Services

  • Configure static and dynamic NAT/PAT and verify translations with show ip nat translations

  • Configure and verify a DHCP server and relay agent on a router

  • Configure NTP, syslog, and SNMPv3 basics, and read a syslog severity level table

  • Explain DNS lookup flow and the role of the DNS server record types relevant to a network engineer

  • Describe QoS concepts: classification, marking, queuing, shaping/policing, and where each fits

  • Compare file-transfer and management-plane services (TFTP, FTP, SCP) and their security implications

Your checkpoint

Deploy a lab with PAT to an outside network, a DHCP pool with relay, and centralized syslog plus NTP; capture configuration and show-command output proving each service works

Week 7

Automation and Programmability

  • Interpret JSON-encoded data and identify objects, arrays, keys, and values in a sample response

  • Explain REST API characteristics (statelessness, HTTP verbs, status codes) and authenticate to a sandbox controller API

  • Compare configuration-management models: traditional CLI, controller-based, and infrastructure-as-code

  • Distinguish the roles of Ansible, Puppet, and Chef and identify which are agentless vs agent-based

  • Describe SDN architecture layers (data, control, application planes) and the function of a DNA Center-style controller

  • Explain the purpose of a Python script using a network library at a conceptual level

Your checkpoint

Write a one-page summary that decodes a sample JSON API payload field by field and maps three automation tools plus SDN planes onto a hand-drawn architecture diagram

Week 8

Network Fundamentals & Network Access & IP Connectivity & IP Services & Security Fundamentals & Automation and Programmability

  • Re-run every missed quiz item from Weeks 1-7 and log the root cause of each error

  • Complete two full-length timed practice exams and score each domain separately

  • Reconfigure the three highest-error topics from a blank device configuration

  • Build a one-page cheat sheet of subnetting shortcuts, show commands, and OSPF/STP decision rules

  • Verify readiness by scoring at or above target on every domain, not just in aggregate

Your checkpoint

Two full-length practice exams scored with per-domain breakdowns, plus a remediation sheet listing every sub-70% domain and the exact lab or drill you will repeat before test day

Milestones

Week 2: Explain the routing table out loud from a captured show ip route, and pass a 20-question subnetting drill at 90% or better

Week 4: All six domains' core show commands are recognizable, and the Layer 2 lab passes end-to-end connectivity with correct STP root placement

Week 6: Score 70% or higher per domain on a first full-length practice exam, with no domain below 60%

Week 8: Score 85% or higher overall and at least 80% in each of Domains 1, 2, and 3 on the final practice exam

CCNA exam day

Your checklist

Government-issued photo ID with your signature on it

Your name must match your exam registration exactly, including middle names and suffixes. An expired ID or a name mismatch is the most common reason candidates are turned away, so compare your ID against your registration confirmation line by line today.

A second form of identification, if your provider requires one

Some test centres and online-proctored deliveries ask for a second ID (for example a bank card or a second government document). Do not assume one is enough - confirm with the provider before exam day what forms are accepted.

Appointment confirmation or registration number

Save the confirmation email or take a screenshot of the appointment ID, exam code (200-301 for CCNA), date, time and test-centre address. You usually will not need to show it, but it resolves check-in disputes quickly.

A verified route to the test centre, or a completed system test for online delivery

For a physical centre, do a dry run so you know the building, parking and security screening time. For online proctoring, run the provider's system test on the same machine, network and webcam you will use, and plan a wired-or-stable connection.

Confirmation of what scratch material is allowed

Many centres supply an erasable board or paper and pen, and online-proctored sessions may permit a laminated sheet or an on-screen whiteboard. You are generally not allowed to bring your own notes. Confirm with the provider which materials will be supplied for your delivery mode.

Everything personal left at home or in a locker

Phones, smartwatches, fitness bands, notes, books, bags and printed study sheets are not permitted in the testing room. Assume there is no secure place for valuables beyond a provided locker or your car.

A one-page review sheet to read BEFORE you enter, not to take in

Limit it to high-yield recall items: subnetting maths for /24–/30, administrative distances, spanning-tree port states and timers, OSPF neighbour requirements, first-hop redundancy and wireless/WAN basics. Read it in the car or lobby, then put it away.

A pacing plan written down

For roughly 120 minutes of testing time, budget about 70 seconds per question if the exam runs around 100 items. Flag mentally any question eating more than two minutes and move on - the question count can vary, so confirm the format in the pre-exam tutorial rather than assuming a fixed number.

Knowledge of the exam code and current blueprint you registered for

Confirm on the vendor's official exam topics page that you booked 200-301 and that your study material matches the current published blueprint, since objectives are revised periodically.

A restroom and water stop planned before check-in

Check-in and the exam itself are long. Use the restroom immediately before you are seated or before you start the online session, because leaving mid-exam usually costs you testing time.

A realistic arrival buffer

Aim to be at the centre well before your appointment slot so that ID checks and the test-centre agreement do not eat into exam time. Confirm the provider's recommended arrival window when you book.

A plan for the score report

The preliminary result is normally shown or issued at the end of the session, with the formal record following by email or in your certification account. Know where to look, and do not close the browser or leave the centre until you have it.

Plan the day

Final 72 hours

Stop adding new topics. Re-read the official exam topics list and mark each objective as confident, shaky or unknown. Spend the remaining time only on 'shaky' items - that is where points are cheapest.

Final 72 hours

Do two or three timed practice sets under exam conditions: no pauses, no notes, no phone. Score them and write down every miss with a one-line reason (misread, didn't know, ran out of time). Fix the 'misread' category first - it is free marks.

Final 72 hours

Drill subnetting until you can answer 'what is the network, broadcast and usable range' for a /25–/30 in under 30 seconds without writing out a full table. This is the single highest-leverage speed skill on the exam.

Final 72 hours

Log in to the booking system and re-confirm date, time, time zone, delivery mode and test-centre address. Check the ID you plan to use is unexpired and the name matches the registration exactly.

Final 24 hours

Do a light pass only: your one-page recall sheet, a handful of mixed practice questions, and a walk-through of CLI patterns you might see in interactive items (interface configuration, VLAN assignment, static routes, OSPF and default route basics).

Final 24 hours

Prepare logistics physically: ID in your wallet or bag, appointment confirmation saved offline, route or system test done, clothes and travel sorted. Charge your phone but plan to leave it out of the room.

Final 24 hours

Stop studying at a fixed hour in the early evening, eat a normal meal, avoid alcohol, and get a full night's sleep. Cramming past midnight reliably costs more marks than it earns.

Morning of

Eat a proper meal with protein and have a modest amount of caffeine - the same amount you normally have, not more. An unfamiliar double espresso before a 120-minute focused session is a bad trade.

Morning of

Read your one-page recall sheet for 15 minutes only, then put it away. Do not attempt a full practice exam or start a new topic; a bad score an hour before the test just spikes anxiety.

Morning of

Arrive at the centre or log in for online proctoring ahead of the appointment time so ID verification, the room scan and the candidate agreement finish before your clock starts. Confirm the provider's recommended check-in lead time in advance.

During the test

Read the pre-exam tutorial properly rather than clicking through it. It tells you the navigation rules - specifically whether you can flag and return to earlier questions, which changes your pacing strategy.

During the test

Answer every single question. There is normally no credit for blanks and no separate penalty for a wrong answer, so an educated guess always beats a skipped item.

During the test

For configuration-style items, read the whole prompt first, note exactly what is being asked (a specific verification command output, not a complete design), and commit the minimum configuration that satisfies it.

During the test

Watch the clock at the halfway point. If you are behind, switch to a faster mode: eliminate two obviously wrong options, pick from the rest, and move. Never let one drag-and-drop item consume five minutes.

During the test

If you finish early, use any remaining time to revisit only the questions you flagged as guesses - not ones you already reasoned through - then submit and collect your result.

Rules to check

  • You will be asked to accept a candidate agreement or non-disclosure terms before the exam starts. Read it and accept it; declining usually ends the session and forfeits your fee.

  • The name on your registration must match your photo ID exactly. If you have recently married, changed your name or registered with a nickname, contact the provider to correct the booking before exam day - this cannot be fixed at the counter.

  • No notes, books, phones, smartwatches or other devices in the testing room, and no talking or reading aloud during an online-proctored session. Possession of a device can void your score regardless of whether you used it, so confirm the provider's rules on personal items and storage.

  • Breaks are generally not built into the exam clock, and unscheduled breaks typically count against your remaining testing time. Confirm the exact break policy for your delivery mode with the provider before you book, and plan not to need one.

  • Scoring is on a scaled range (Cisco reports CCNA on a 300–1000 scale) with no partial credit within a question, and the exact passing threshold is set by the certification programme rather than published as a single guaranteed number for every form. Treat any 'pass mark' you have read online as approximate and confirm with the provider.

  • Do not assume you can go back to previous questions. Some question types lock once answered. Use the tutorial to learn the navigation behaviour before question one, and if you cannot return, resolve each item as you go rather than deferring decisions.

  • Attempt limits apply: if you do not pass, there is typically a waiting period before you may retake the same exam, plus a cap on attempts within a set window. Confirm the current retake policy with the provider before you rebook.

  • The certification is time-limited and must be recertified - through continuing education credits or by passing a qualifying higher-level exam - typically on a three-year cycle. Check your certification account for your exact expiry date rather than relying on the exam date.

CCNA FAQ

How many CCNA (200-301) practice questions are available?

The practice set has 200 CCNA (200-301) questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many CCNA (200-301) flashcards are available?

The flashcard set has 32 CCNA (200-301) cards. Each card shows the term and its definition.

Which topics does the CCNA (200-301) study material cover?

The CCNA (200-301) study material has 6 sections, including Network Fundamentals, Network Access, and IP Connectivity.

What format facts does the catalog list for the CCNA (200-301) exam?

The catalog lists a duration of 120 minutes and these item types: multiple choice, multiple response, drag and drop, fill in the blank, and simulation / lab testlet for the CCNA (200-301) exam.