VIC Heavy Rigid Knowledge Test Practice Test

VIC Heavy Rigid Knowledge Test overview

  • 200 practice questions
  • 32 flashcards
  • 6 study guide topics
  • 40 key terms

What you'll study

  • Heavy vehicle licensing, vehicle categories and mass limits17%
  • Pre-start checks, vehicle inspection and defects17%
  • Load restraint and load security17%
  • Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)17%
  • Road rules, signage and sharing the road safely16%
  • Fatigue management, work diaries and emergency procedures16%

The Victorian Heavy Rigid (HR) licence knowledge test is the theory-assessment step for drivers who want to move from a car or light-rigid licence into the heavy rigid class - the class that covers rigid trucks and other heavy rigid motor vehicles above the light-rigid threshold. It is aimed at people who already hold a lower class of licence, want to work in transport, logistics, construction, waste or agricultural haulage, or need HR as a stepping stone toward heavier combinations. The knowledge test is a multiple-choice assessment delivered at a VicRoads customer service centre, and it sits alongside the practical requirements for the class rather than replacing them.

The assessment samples the knowledge a HR driver needs before getting behind the wheel: how heavy vehicle licensing and vehicle categories work, what mass limits apply, how to do a proper pre-start inspection and recognise defects, how to restrain and secure a load, and how heavy vehicles must be braked, geared, cornered and spaced in traffic. It also covers general road rules, signage and sharing the road, plus fatigue management, work diary obligations and emergency procedures.

Preparation should be built on the current official Victorian heavy vehicle handbook or driver guide, read topic by topic, followed by practice questions and review of every wrong answer. Confirm current test details with VicRoads before booking.

Common mistakes

Treating the GVM on the compliance plate as the payload allowance - loading the truck to GVM without subtracting the tare mass, and ignoring GCM entirely when a trailer is attached.

GVM is the number people see quoted in ads, registration papers and licence definitions, so it gets mentally filed as 'how much I can carry'. GCM is rarely mentioned day to day and only bites once a trailer or dog trailer is hooked up.

What to do instead

Learn the three-mass hierarchy as a single worked example: GVM = tare + payload; GCM = loaded prime mover/rigid + loaded trailer(s); and no axle group may exceed its own limit even when the total is legal. Practise one calculation with real numbers (e.g. tare 8.5 t, GVM 15 t, so maximum payload 6.5 t) until the subtraction becomes automatic.

Assuming a Heavy Rigid licence lets you tow a trailer of any size, or that an HR truck can be driven with a car-style trailer endorsement logic.

Candidates generalise from the car licence system, where the class of vehicle you can drive and the trailer you can tow are only loosely connected. The HR trailer limit is a specific figure that appears in the licence definition and nowhere in everyday driving.

What to do instead

Memorise the HR definition as two numbers: a rigid motor vehicle with a GVM over 8 tonnes, towing a trailer with a GTM not over 9 tonnes. If a question pairs an HR truck with a heavy trailer, check the 9 tonne GTM figure before answering.

Performing the pre-start check as a cab-side formality - ticking boxes without walking around the vehicle, and without checking coupling security, tyre condition and a stationary brake test.

Scheduling pressure and familiarity with the same truck every day. Drivers feel the vehicle 'drove in fine yesterday', so the check becomes a signature rather than an inspection.

What to do instead

Adopt a fixed sequence that physically moves you around the vehicle: start at the driver's door, work clockwise, finish with the engine running checks (air build-up and leak-down, brake test, lights). Treat the checklist as a route map, not a memory test - the sequence is what stops you skipping the kingpin or the inside duals.

Not knowing what to do once a defect is found - driving on with a defect that should ground the vehicle, or failing to record and report a defect that was identified.

Candidates study defects as a list of parts to look at but never learn the consequence step. In the yard, there is also pressure to 'get the load there' rather than park the truck.

What to do instead

Learn the classification and its consequence as one unit: a major defect means the vehicle must not be driven until repaired; a minor defect must be reported and recorded. Know that the report goes to the operator and into the defect record/work diary, and that the driver who identifies the defect owns the report.

Getting the load restraint performance standards wrong - quoting 100% of the load's weight in every direction, or guessing at figures like 60% or 'half the weight'.

The percentages feel arbitrary and are easy to half-remember, and in practice many drivers restrain loads 'tight enough' by feel rather than to a specified standard.

What to do instead

Lock in the three figures: the restraint system must withstand 80% of the load's weight forward, 50% rearward and 50% sideways. Remember it as 'forward is the hardest stop' - the forward figure is the largest because that is where the load moves under heavy braking.

Securing the load once at the start of the trip and never re-checking it, including after heavy braking or rough road sections.

Straps stretch, webbing settles, and loads compact over the first few kilometres. Drivers assume 'I tensioned it, so it is tensioned' and only look again if something feels wrong.

What to do instead

Build re-checks into the trip plan: a stop within the first 20โ€“50 km to re-tension and confirm the load has not shifted, then another check at every rest stop and after any heavy braking or off-road section. Loose or damaged straps and missing edge protection are replaced, not reused.

Descending long or steep grades on the footbrake alone, riding the pedal to hold speed, rather than selecting a low gear and using engine braking before the descent begins.

Car habits transfer directly - in a car you brake to slow down, and the gearbox is almost incidental. Candidates also fear over-revving and so stay in a high gear.

What to do instead

Change down and set the speed before the crest, not once the descent has started, and use short firm brake applications rather than continuous light pressure so the brakes have time to cool. Know the signs of brake fade and the escape options if fade occurs.

Applying a two-second following gap, or judging the gap by 'feel', when driving a loaded heavy vehicle.

The two-second rule is the one most strongly associated with learner driving and is the number candidates remember. Mass, tyre condition and load all lengthen stopping distance, but none of that is visible in the gap itself.

What to do instead

Use a three-to-four second minimum in good conditions and add time for a loaded vehicle, wet roads, night or following another heavy vehicle. Count it against a fixed roadside object, not by eye, and remember the vehicle behind you may need more room than you do.

Filling in the work diary retrospectively at the end of the shift and treating loading, unloading and waiting at a depot as rest.

The diary feels like paperwork to be tidied up later, and waiting around a site feels like time off. Both assumptions understate work time and hide an approaching limit.

What to do instead

Record at each change of activity, not at day's end, and count loading, unloading, inspecting, cleaning and waiting on duty as work time. Plan the required minimum break before you reach the continuous work limit under standard hours, and carry the diary with you and retain it as required.

Misreading heavy-vehicle signage - passing a load-limited bridge without comparing the sign to the actual loaded mass, or ignoring a low clearance sign because the truck 'fits under it empty'.

These signs are read as advisory car-style warnings, and the truck's height is mentally fixed at its unladen height. Load limits are also compared to GVM rather than to what the vehicle actually weighs at that moment.

What to do instead

Know that a load limit sign applies to the actual gross mass of the vehicle at that time, not to its GVM or its registration, and that a clearance sign applies to your height including any load or raised equipment. Where the margin is close, stop and check rather than proceed on assumption.

Exam requirements can change. Confirm current details with the exam provider.

VIC Heavy Rigid Knowledge Test practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Heavy vehicle licensing, vehicle categories and mass limits

    Which Victorian licence class is required to drive a rigid vehicle with a GVM of 15 tonnes and three axles?

    1. Light Rigid (LR)
    2. Heavy Rigid (HR) Correct answer.
    3. Medium Rigid (MR)
    4. Heavy Combination (HC)

    Explanation

    A rigid vehicle with a GVM over 8 tonnes and three or more axles falls within the Heavy Rigid class. Medium Rigid is limited to two-axle rigid vehicles over 8 tonnes. Heavy Combination covers articulated combinations, and Light Rigid covers 4.5 to 8 tonnes.

  2. Question 2Heavy vehicle licensing, vehicle categories and mass limits

    Which description matches a Medium Rigid (MR) vehicle?

    1. A rigid vehicle with three axles and a GVM over 8 tonnes
    2. A rigid vehicle with two axles and a GVM over 8 tonnes Correct answer.
    3. A rigid vehicle with a GVM between 4.5 and 8 tonnes
    4. An articulated vehicle consisting of a prime mover and semi-trailer

    Explanation

    Medium Rigid covers a rigid vehicle with two axles and a GVM greater than 8 tonnes, and it may tow a trailer up to 9 tonnes GVM. A three-axle rigid vehicle over 8 tonnes is Heavy Rigid. A 4.5 to 8 tonne rigid vehicle is Light Rigid, and a semi-trailer is Heavy Combination.

  3. Question 3Heavy vehicle licensing, vehicle categories and mass limits

    Which licence class covers a rigid vehicle with a GVM of 6 tonnes?

    1. Car (C)
    2. Medium Rigid (MR)
    3. Heavy Rigid (HR)
    4. Light Rigid (LR) Correct answer.

    Explanation

    Light Rigid covers rigid vehicles with a GVM over 4.5 tonnes and up to 8 tonnes. A car licence covers vehicles up to 4.5 tonnes GVM. Medium Rigid requires a GVM over 8 tonnes, and Heavy Rigid requires three or more axles over 8 tonnes.

  4. Question 4Heavy vehicle licensing, vehicle categories and mass limits

    Under Victorian heavy vehicle arrangements, a motor vehicle is generally a heavy vehicle when its GVM exceeds:

    1. 2 tonnes
    2. 4.5 tonnes Correct answer.
    3. 4.0 tonnes
    4. 3.5 tonnes

    Explanation

    Heavy vehicle law applies to motor vehicles with a GVM over 4.5 tonnes, and to combinations that include them. Vehicles at or below 4.5 tonnes GVM are dealt with under light vehicle and car licence rules.

  5. Question 5Heavy vehicle licensing, vehicle categories and mass limits

    GVM stands for gross vehicle mass. What does it represent?

    1. The mass of the vehicle with no load
    2. The maximum loaded mass of the vehicle itself Correct answer.
    3. The mass of the vehicle plus any trailer it tows
    4. The maximum mass allowed on the rear axle

    Explanation

    GVM is the maximum mass of the motor vehicle when loaded, set by the manufacturer and subject to legal limits. It does not include the mass of a trailer, which is dealt with under the combination mass. Axle limits are separate from GVM.

  6. Question 6Heavy vehicle licensing, vehicle categories and mass limits

    The tare mass of a heavy vehicle is:

    1. The maximum load it may carry
    2. The mass of the load plus the driver
    3. The maximum mass of a trailer it may tow
    4. Its unladen mass, including fluids and standard equipment Correct answer.

    Explanation

    Tare mass is the mass of the vehicle as built and operating with no payload, typically including fuel, oil, coolant and standard equipment. Payload is found by subtracting tare from GVM. Tare does not include the goods being carried.

  7. Question 7Heavy vehicle licensing, vehicle categories and mass limits

    A rigid truck has a GVM of 12 tonnes and a tare mass of 5 tonnes. What is its maximum payload under those ratings?

    1. 17 tonnes
    2. 7 tonnes Correct answer.
    3. 5 tonnes
    4. 12 tonnes

    Explanation

    Payload is calculated by subtracting tare from GVM: 12 tonnes minus 5 tonnes equals 7 tonnes. This assumes the load is distributed so that no axle or axle group limit is exceeded. The legal load may be lower if the vehicle's configuration or registration restricts it.

  8. Question 8Heavy vehicle licensing, vehicle categories and mass limits

    Gross combination mass (GCM) is best described as:

    1. The mass of the trailer when fully loaded
    2. The maximum mass permitted on a tandem axle group
    3. The mass of the prime mover alone when loaded
    4. The maximum loaded mass of a motor vehicle plus any trailers it tows Correct answer.

    Explanation

    GCM is the maximum loaded mass allowed for the whole combination, including the towing vehicle and trailer or trailers. It is different from GVM, which applies to the vehicle by itself. Both GCM and GVM must be satisfied.

  9. Question 9Heavy vehicle licensing, vehicle categories and mass limits

    Which licence class is required to drive a prime mover attached to a semi-trailer?

    1. Medium Rigid (MR)
    2. Heavy Combination (HC) Correct answer.
    3. Multi-Combination (MC)
    4. Heavy Rigid (HR)

    Explanation

    Heavy Combination covers articulated combinations such as a prime mover and semi-trailer, and rigid vehicles towing trailers over 9 tonnes. Multi-Combination is for multiple trailers such as B-doubles and road trains. Heavy Rigid and Medium Rigid are rigid vehicle classes.

  10. Question 10Heavy vehicle licensing, vehicle categories and mass limits

    Driving a B-double requires which Victorian licence class?

    1. Heavy Rigid (HR)
    2. Heavy Combination (HC)
    3. Multi-Combination (MC) Correct answer.
    4. Medium Rigid (MR)

    Explanation

    A B-double is a combination involving two trailers, so it falls under Multi-Combination. Heavy Combination covers a single semi-trailer. Heavy Rigid and Medium Rigid are rigid vehicle classes and do not cover multiple trailers.

  11. Question 11Heavy vehicle licensing, vehicle categories and mass limits

    The holder of a Heavy Rigid licence may tow a trailer with a GVM of up to:

    1. 9 tonnes Correct answer.
    2. 12 tonnes
    3. 6 tonnes
    4. 4.5 tonnes

    Explanation

    Heavy Rigid allows a rigid vehicle over 8 tonnes with three or more axles to tow a trailer with a GVM not exceeding 9 tonnes. Towing a trailer over 9 tonnes generally requires Heavy Combination. A car licence towing limit is 4.5 tonnes.

  12. Question 12Heavy vehicle licensing, vehicle categories and mass limits

    A person with only a car (C) licence in Victoria may tow a trailer with a maximum GVM of:

    1. 2 tonnes
    2. 3 tonnes
    3. 4.5 tonnes Correct answer.
    4. 750 kg

    Explanation

    A car licence permits towing a trailer up to 4.5 tonnes GVM, provided the towing vehicle's capacity and GCM are not exceeded. Anything above 4.5 tonnes GVM requires an appropriate heavy vehicle class. The trailer's actual mass must also remain within its ratings.

  13. Question 13Heavy vehicle licensing, vehicle categories and mass limits

    A prime mover is loaded so that it is under its GVM, but the combination exceeds the prime mover's GCM. Is this permitted?

    1. No, the combination must also stay within the GCM Correct answer.
    2. Yes, because GVM is the only legal limit
    3. Yes, provided the trailer is under its ATM
    4. No, because the prime mover must be empty when towing

    Explanation

    Both GVM and GCM, as well as axle and axle-group limits, must be satisfied. GCM limits the total mass of the towing vehicle and trailer or trailers. Staying under GVM alone does not make an over-GCM combination legal.

  14. Question 14Heavy vehicle licensing, vehicle categories and mass limits

    A tandem axle group on a heavy vehicle is found to be above its specified group mass limit. The vehicle's total mass is under GVM. What is the status?

    1. Legal, because each individual axle is under its own limit
    2. Legal, because total GVM is not exceeded
    3. Legal if the steer axle is under its limit
    4. Overloaded on that axle group, even though GVM is not exceeded Correct answer.

    Explanation

    Axle and axle-group limits apply independently of GVM. A group can be over its limit even when total vehicle mass is under GVM. The load must be redistributed or reduced to bring the group within its limit.

  15. Question 15Heavy vehicle licensing, vehicle categories and mass limits

    When a manufacturer's GVM rating is lower than the legal mass limit for the vehicle's configuration, the maximum legal operating mass is:

    1. The manufacturer's rating Correct answer.
    2. Whichever figure the driver chooses
    3. The legal limit, because legislation overrides the plate
    4. The higher of the two figures

    Explanation

    The lower of the manufacturer's rating and the legal limit applies. A vehicle must not be loaded beyond its manufacturer's GVM even if legislation would allow more for that axle configuration. This protects the vehicle's design limits.

  16. Question 16Heavy vehicle licensing, vehicle categories and mass limits

    Aggregate trailer mass (ATM) is:

    1. The mass of the trailer when empty
    2. The maximum mass of a loaded trailer, including its own weight and load Correct answer.
    3. The maximum mass a trailer may impose on the towing vehicle's coupling
    4. The mass of the trailer plus its payload divided by the number of axles

    Explanation

    ATM is the maximum loaded mass of the trailer, as specified by the manufacturer and subject to legal limits. It includes the trailer's tare plus its payload. It is not the same as the mass imposed on the towing vehicle's coupling.

  17. Question 17Heavy vehicle licensing, vehicle categories and mass limits

    A rigid truck is rated to tow a trailer with a maximum ATM of 8 tonnes. The driver wants to tow a trailer with an ATM of 10 tonnes. What applies?

    1. It is permitted if the truck is under its GVM
    2. It is permitted if the driver holds an HR licence
    3. The combination is not permitted because the trailer exceeds the truck's towing rating Correct answer.
    4. It is permitted if the trailer is only partly loaded

    Explanation

    A towing vehicle must not exceed its rated towing capacity or ATM, even if the trailer is partly loaded. The combination must also satisfy GCM and axle limits. Licence class does not change the vehicle's mass ratings.

  18. Question 18Heavy vehicle licensing, vehicle categories and mass limits

    In Victoria, the registered mass of a heavy vehicle should be:

    1. Always exactly the GVM
    2. The tare mass only
    3. Lower than GVM to reduce registration cost
    4. At least the maximum mass at which the vehicle will operate Correct answer.

    Explanation

    Registration is based on a mass that covers the vehicle's intended operating mass; operating above the registered mass can breach registration conditions. The registered mass must be sufficient for actual loads. It is not necessarily the tare or exactly the GVM.

  19. Question 19Heavy vehicle licensing, vehicle categories and mass limits

    A combination cannot comply with standard mass limits for a particular journey. What is the usual lawful pathway?

    1. Apply for an oversize or overmass permit or follow an approved notice Correct answer.
    2. Reduce speed and proceed without any approval
    3. Drive at night to avoid detection
    4. Use hazard lights and exceed limits by up to 10%

    Explanation

    Mass and dimension limits can only be exceeded under an appropriate permit or notice. Penalties apply to unapproved overmass operation. Speed, lighting or time of day does not create an exemption.

  20. Question 20Heavy vehicle licensing, vehicle categories and mass limits

    A load is moved rearward on a rigid truck. What is the likely effect on axle loads?

    1. Front axle load decreases and rear axle load increases Correct answer.
    2. Both axle loads decrease
    3. Front axle load increases and rear axle load decreases
    4. Both axle loads stay the same if total mass is unchanged

    Explanation

    Moving mass rearward shifts weight from the steer axle to the rear axle group. This can overload the rear group even if total mass is unchanged. Load position is critical to compliance with axle and group limits.

  21. Question 21Heavy vehicle licensing, vehicle categories and mass limits

    A driver holds an HR licence and wants to tow a trailer with a GVM of 10 tonnes using a three-axle rigid truck. Which class is required?

    1. Heavy Rigid (HR) is sufficient
    2. Heavy Combination (HC) Correct answer.
    3. Medium Rigid (MR)
    4. Multi-Combination (MC)

    Explanation

    Heavy Rigid covers towing trailers only up to 9 tonnes GVM. A trailer over 9 tonnes behind a rigid vehicle requires Heavy Combination. Multi-Combination is only for multiple trailers.

  22. Question 22Heavy vehicle licensing, vehicle categories and mass limits

    A rigid truck has a GVM of 15 tonnes and a GCM of 20 tonnes. It is loaded to its GVM and tows a trailer with a loaded mass of 6 tonnes. What is the combination mass and is it compliant?

    1. 20 tonnes; compliant because GCM is not exceeded
    2. 21 tonnes; not compliant because GCM is exceeded Correct answer.
    3. 21 tonnes; compliant because the truck is within GVM
    4. 15 tonnes; compliant because only the truck's mass counts

    Explanation

    Combination mass is 15 plus 6, which equals 21 tonnes and exceeds the 20 tonne GCM. Meeting GVM does not excuse exceeding GCM. The load or trailer mass must be reduced.

  23. Question 23Heavy vehicle licensing, vehicle categories and mass limits

    GTM (gross trailer mass) differs from ATM because GTM is:

    1. The total loaded mass of the towing vehicle and trailer together
    2. The maximum loaded mass carried by the trailer's axles, excluding the mass imposed on the towing vehicle Correct answer.
    3. The maximum mass the trailer's coupling can impose on the towing vehicle
    4. The trailer mass when empty

    Explanation

    GTM is the maximum mass supported by the trailer's own axles. It excludes the portion of the trailer's mass carried by the towing vehicle through the coupling or fifth wheel. ATM includes the whole loaded trailer mass.

  24. Question 24Heavy vehicle licensing, vehicle categories and mass limits

    A rigid truck has a GVM of 12 tonnes and a GCM of 18 tonnes. It is loaded to 12 tonnes and tows a trailer rated to ATM 8 tonnes. What maximum trailer load mass does the GCM allow?

    1. 8 tonnes
    2. 18 tonnes
    3. 6 tonnes Correct answer.
    4. 12 tonnes

    Explanation

    GCM of 18 tonnes minus the truck's 12 tonnes leaves 6 tonnes for the trailer. This is less than the trailer's 8 tonne ATM, so the GCM is the controlling limit. The lower limit must be used.

  25. Question 25Heavy vehicle licensing, vehicle categories and mass limits

    The load a semi-trailer imposes on the prime mover through the fifth wheel:

    1. Is limited only by the trailer's ATM rating
    2. Is excluded from all mass limits because it is a trailer load
    3. Forms part of the prime mover's GVM and the combination mass Correct answer.
    4. Is counted only against the trailer's GTM

    Explanation

    The fifth-wheel or kingpin load is carried by the prime mover, so it counts toward the prime mover's GVM and the combination mass. GTM excludes it, but that does not remove it from the towing vehicle's limits. Exceeding it can overload the prime mover.

  26. Question 26Heavy vehicle licensing, vehicle categories and mass limits

    Under Victorian licensing rules, a light rigid vehicle is one with a gross vehicle mass (GVM) of:

    1. over 12 tonnes
    2. 4.5 tonnes or less
    3. over 8 tonnes up to 12 tonnes
    4. over 4.5 tonnes up to 8 tonnes Correct answer.

    Explanation

    The light rigid (LR) class covers vehicles with a GVM above 4.5 tonnes and up to 8 tonnes. Anything at or below 4.5 tonnes is driven on a car licence, while heavier rigid vehicles move into the medium and heavy rigid classes.

  27. Question 27Heavy vehicle licensing, vehicle categories and mass limits

    Under general mass limits, the maximum mass permitted on a tandem axle group fitted with dual tyres is:

    1. 16.5 tonnes Correct answer.
    2. 20.0 tonnes
    3. 13.0 tonnes
    4. 15.0 tonnes

    Explanation

    General mass limits allow 16.5 tonnes on a tandem axle group with dual tyres. For comparison, a tri-axle group is allowed 20.0 tonnes and a single axle with dual tyres is allowed 9.0 tonnes.

  28. Question 28Heavy vehicle licensing, vehicle categories and mass limits

    For registration and mass-management purposes in Victoria, a heavy vehicle is one that has a GVM of more than:

    1. 12 tonnes
    2. 8 tonnes
    3. 4.5 tonnes Correct answer.
    4. 3.5 tonnes

    Explanation

    A heavy vehicle is defined by its GVM exceeding 4.5 tonnes. At or below that figure the vehicle is a light vehicle and the heavy vehicle mass and registration rules do not apply.

  29. Question 29Heavy vehicle licensing, vehicle categories and mass limits

    A two-axle table-top truck has a GVM of 10 tonnes. Which Victorian licence class is required to drive it?

    1. Medium Rigid (MR) Correct answer.
    2. Heavy Combination (HC)
    3. Heavy Rigid (HR)
    4. Light Rigid (LR)

    Explanation

    The medium rigid class covers two-axle vehicles with a GVM above 8 tonnes and up to 12 tonnes. A 10 tonne two-axle truck therefore falls squarely within MR.

  30. Question 30Heavy vehicle licensing, vehicle categories and mass limits

    A three-axle rigid truck is loaded so that its steer axle carries 6.6 tonnes. Every other axle group and the truck's total mass are within their limits. What is the status of this load?

    1. It is lawful provided the drive group is under its limit
    2. It is lawful because the total mass is within the GVM
    3. It is unlawful because the steer axle exceeds its 6.0 tonne limit Correct answer.
    4. It is lawful because single steer axles are not subject to mass limits

    Explanation

    Under general mass limits a single steer axle may carry no more than 6.0 tonnes. Each axle and axle group must comply in its own right, so exceeding one axle limit is a breach even when total mass and the other groups are fine.

  31. Question 31Heavy vehicle licensing, vehicle categories and mass limits

    A trailer that carries its load on its own axle group at the front and another at the rear, and is connected to the towing vehicle by a rigid drawbar, is known as a:

    1. dog trailer Correct answer.
    2. converter dolly
    3. pig trailer
    4. semi-trailer

    Explanation

    A dog trailer has two axle groups of its own and is towed by a drawbar. By contrast, a pig trailer has only one axle group and a semi-trailer has no front axle group at all.

  32. Question 32Heavy vehicle licensing, vehicle categories and mass limits

    A tandem axle group on a rigid truck carries a manufacturer's rating of 15.0 tonnes, while the general mass limit for a tandem group is 16.5 tonnes. What is the greatest mass the group may legally carry?

    1. No group limit applies as long as the GVM is not exceeded
    2. 15.0 tonnes, as the lower figure applies Correct answer.
    3. 16.5 tonnes, because that is the general mass limit
    4. 16.25 tonnes, which is the average of the two figures

    Explanation

    A vehicle must satisfy both the legal mass limits and the manufacturer's ratings stamped on the vehicle. Where the manufacturer's rating is the lower of the two, that rating becomes the effective maximum for the group.

  33. Question 33Heavy vehicle licensing, vehicle categories and mass limits

    In a heavy combination, a converter dolly is used to:

    1. add a second deck to a semi-trailer so its legal payload increases
    2. couple a semi-trailer behind a rigid truck or another trailer Correct answer.
    3. reduce the mass carried on the prime mover's drive axles when loaded
    4. lengthen a rigid truck's chassis so it can be registered as a prime mover

    Explanation

    A converter dolly is a separate axle group fitted with a fifth wheel and a drawbar. It lets a semi-trailer be towed behind a rigid truck or another trailer, producing combinations such as a truck and dog or a B-double arrangement.

  34. Question 34Heavy vehicle licensing, vehicle categories and mass limits

    Under general mass limits, the maximum gross mass of a six-axle articulated vehicle (three-axle prime mover with three-axle semi-trailer) is:

    1. 46.0 tonnes
    2. 45.5 tonnes
    3. 42.5 tonnes Correct answer.
    4. 39.0 tonnes

    Explanation

    General mass limits permit 42.5 tonnes for a six-axle articulated vehicle. The higher 45.5 tonne figure is only available where concessional or higher mass limits apply and the vehicle meets the extra conditions.

  35. Question 35Pre-start checks, vehicle inspection and defects

    What is the main purpose of a pre-start inspection on a heavy rigid vehicle?

    1. To find faults or damage before they become a safety risk Correct answer.
    2. To confirm that the vehicle's registration has been renewed for the current period
    3. To work out how much fuel the day's deliveries will use
    4. To decide whether the vehicle needs to be washed before departure

    Explanation

    A pre-start inspection is a systematic physical check of the vehicle carried out before it is used, so that faults are found and fixed before they cause a breakdown or crash. It does not replace scheduled maintenance or administrative tasks.

  36. Question 36Pre-start checks, vehicle inspection and defects

    When must a pre-start inspection be carried out on a heavy vehicle?

    1. Only after the vehicle has been serviced
    2. Once every seven days of operation
    3. Before the vehicle is first used each day Correct answer.
    4. Whenever the registration is due for renewal

    Explanation

    A check must be done before the vehicle's first use each day so defects are identified before it enters the road network. On a multi-day trip the checks continue each day, not just on the first day.

  37. Question 37Pre-start checks, vehicle inspection and defects

    During a pre-start check you find a deep cut in a rear tyre that exposes the cords. What should you do?

    1. Seal the cut with a plug and continue the journey
    2. Reduce speed for the trip and keep a close watch on the tyre
    3. Leave the vehicle parked until the tyre is repaired or replaced Correct answer.
    4. Record the cut and check the tyre again at the next scheduled service

    Explanation

    Exposed cords mean the tyre's structure is damaged and it can fail without warning. A tyre in that condition makes the vehicle unroadworthy, so it must not be driven until it is replaced.

  38. Question 38Pre-start checks, vehicle inspection and defects

    What should you check about the vehicle's lights during a pre-start inspection?

    1. That the headlights are brighter than the parking lights
    2. That every globe has been replaced within the last twelve months
    3. That each lamp works and the lenses are clean and unbroken Correct answer.
    4. That the lamps only come on when the engine is running

    Explanation

    All lamps and reflectors must work and be visible so the vehicle can be seen and can signal its intentions. Cracked lenses let water and dirt in and reduce light output.

  39. Question 39Pre-start checks, vehicle inspection and defects

    When is the best time to check engine oil and coolant levels on a heavy vehicle?

    1. When the engine is cold and the vehicle is on level ground Correct answer.
    2. While the engine is idling at operating temperature
    3. Straight after a long highway run
    4. Only when a warning light comes on in the dash

    Explanation

    Checking with a cold engine on level ground gives a true reading and avoids the risk of scalding from a pressurised, hot cooling system. Waiting for a warning light means the problem has already developed.

  40. Question 40Pre-start checks, vehicle inspection and defects

    Before leaving the depot with a loaded heavy rigid vehicle, the driver must ensure the load is:

    1. stacked as high as the vehicle body allows
    2. checked only by the person who loaded the vehicle
    3. covered by a tarpaulin in all weather conditions including fine days
    4. restrained so it cannot move or fall from the vehicle Correct answer.

    Explanation

    The load must be restrained so it can withstand the forces of braking, cornering and road shocks and cannot fall onto the road. The driver remains responsible for confirming the load is secure before moving off.

  41. Question 41Pre-start checks, vehicle inspection and defects

    You find a brake fault during your pre-start inspection. What should you do?

    1. Report the fault and do not use the vehicle until it is repaired Correct answer.
    2. Test the brakes on the road to see whether the fault really matters
    3. Ask another driver whether the fault is serious enough to report
    4. Drive the vehicle today and report the fault at the end of the shift

    Explanation

    A vehicle with a brake defect is unroadworthy and must not be driven. The fault must be reported to the operator and repaired and checked before the vehicle is used.

  42. Question 42Pre-start checks, vehicle inspection and defects

    What is the correct pre-start check for the windscreen, wipers and mirrors?

    1. Check the glass is clean and unbroken and the wipers work Correct answer.
    2. Adjust the mirrors after the vehicle is moving
    3. Apply a tinted film to the windscreen to reduce glare
    4. Wash the windscreen at the end of each shift

    Explanation

    The driver must have a clear view through the windscreen and mirrors, and working wipers are needed to keep that view in rain. Damage or dirt in the swept area reduces vision and must be dealt with before departure.

  43. Question 43Pre-start checks, vehicle inspection and defects

    After coupling a prime mover to a semitrailer, how does the driver confirm the fifth wheel is properly locked?

    1. The locking jaws are closed and the safety catch is engaged Correct answer.
    2. The trailer's landing legs are resting firmly on the ground
    3. The trailer sits level with the ground when viewed from behind
    4. The turntable has been greased and the air lines are connected

    Explanation

    The fifth wheel must be fully locked so the trailer cannot separate from the prime mover. The safety catch or dog clip stops the release handle from opening while the vehicle is in service.

  44. Question 44Pre-start checks, vehicle inspection and defects

    Before driving a heavy vehicle fitted with air brakes, the driver should confirm that:

    1. the brakes release only when the engine is switched off
    2. the compressor builds pressure up to the normal cut-out point Correct answer.
    3. the low pressure warning stays on while the vehicle is moving
    4. the air tanks are fully drained before the trip begins

    Explanation

    Air pressure must reach the normal operating range before the vehicle is driven, otherwise the brakes may not apply or release properly. The low pressure warning should go out once pressure is up.

  45. Question 45Pre-start checks, vehicle inspection and defects

    What is the purpose of the wheel nut indicators fitted to a heavy vehicle's wheels?

    1. They balance the wheel and reduce vibration at speed
    2. They lock the wheel nuts so they cannot be removed
    3. They show the correct inflation pressure for the tyre
    4. They make it easy to see if a wheel nut has begun to loosen Correct answer.

    Explanation

    Indicators are aligned with each other when the nuts are correctly torqued. If an arrow has moved out of line, the nut may be loose and the wheel must be checked before the vehicle is used.

  46. Question 46Pre-start checks, vehicle inspection and defects

    How should tyre pressures be checked on a heavy vehicle?

    1. By kicking the tyre and listening for a hollow sound
    2. After a long trip when the tyres are at their normal operating temperature
    3. Only when a tyre looks flat to the eye
    4. When the tyres are cold, against the manufacturer's recommendation Correct answer.

    Explanation

    Pressures rise as tyres heat up, so a hot reading is higher than the true cold setting and can hide under-inflation. Checking cold against the recommended figure gives an accurate result.

  47. Question 47Pre-start checks, vehicle inspection and defects

    After starting the engine you notice that the ABS warning light stays on. What does this mean?

    1. The vehicle's battery is not being charged by the alternator
    2. The trailer brakes have been applied automatically
    3. The anti-lock braking system has a fault to investigate Correct answer.
    4. The anti-lock braking system has been switched off deliberately

    Explanation

    Most systems run a self-test at start-up and the lamp should go out shortly afterwards. If it stays on, the anti-lock function may not operate and the fault should be reported and checked.

  48. Question 48Pre-start checks, vehicle inspection and defects

    You find a pool of fresh oil under the engine during the pre-start check. What should you do?

    1. Report and investigate the leak before the vehicle is used Correct answer.
    2. Wash the area with water and continue the trip
    3. Top up the oil and note the leak at the next scheduled service
    4. Wipe the oil away and look again at the end of the day

    Explanation

    A new or growing leak can lead to low oil levels and is also a slip hazard at the depot. The source should be identified and the fault reported before the vehicle is used.

  49. Question 49Pre-start checks, vehicle inspection and defects

    Why should a driver record the results of the daily pre-start inspection?

    1. To tell the loader how the vehicle should be loaded
    2. To provide a record that the vehicle's condition was checked Correct answer.
    3. To work out the vehicle's fuel consumption for the week
    4. To show that the driver has taken the required rest breaks

    Explanation

    Records show the check was carried out, allow defects to be tracked through to repair, and support the operator's maintenance obligations. They also provide evidence if the vehicle's condition is later questioned.

  50. Question 50Pre-start checks, vehicle inspection and defects

    A fault develops while you are driving along a highway. What is the correct action?

    1. Stop as soon as it is safe, assess the fault and act to keep the vehicle safe Correct answer.
    2. Stop in the traffic lane and inspect the vehicle where it is
    3. Phone your supervisor and keep driving until you are told to stop
    4. Keep driving at a reduced speed and report it on arrival

    Explanation

    The driver must stop in a safe location, judge whether the vehicle can continue, and report the defect. Continuing with a developing fault can turn a minor problem into a crash or breakdown.

  51. Question 51Pre-start checks, vehicle inspection and defects

    How should a load be placed on a heavy rigid vehicle for safe handling?

    1. Evenly spread and within the vehicle's axle mass limits Correct answer.
    2. Hard against the tailgate so it can be unloaded quickly
    3. As high as possible to keep it away from the floor
    4. Over the rear axle only, to improve traction

    Explanation

    Correct placement keeps each axle within its mass limit and keeps the centre of gravity low and central. This preserves steering grip, braking balance and stability in corners.

  52. Question 52Pre-start checks, vehicle inspection and defects

    What is a minor defect on a heavy vehicle?

    1. A fault that does not stop safe use but must be repaired Correct answer.
    2. A fault that makes the vehicle unsafe to drive at any speed
    3. A fault that requires the vehicle to be towed to a workshop
    4. A fault that the driver is not required to report

    Explanation

    Defects are classified by how they affect safety. A minor defect must be repaired within the time allowed, but it does not prevent the vehicle being used in the meantime.

  53. Question 53Pre-start checks, vehicle inspection and defects

    Who must be told when a driver finds a defect on a heavy vehicle?

    1. Only the next driver who uses the vehicle
    2. The local council, within 24 hours
    3. The operator of the vehicle, who arranges for it to be repaired Correct answer.
    4. No one, if the driver can fix it before departure

    Explanation

    A defect must be reported to the operator so the repair can be arranged and the vehicle kept off the road if necessary. This keeps everyone with responsibility for the vehicle informed.

  54. Question 54Pre-start checks, vehicle inspection and defects

    You notice excessive free play in the steering wheel during the pre-start check. What does this most likely indicate?

    1. The power steering fluid is at the correct level
    2. The wheel alignment was recently corrected
    3. Worn steering components that need inspection Correct answer.
    4. The tyres are inflated to the correct pressure

    Explanation

    Free play is the movement of the wheel before the road wheels respond. Excessive free play points to worn linkages, joints or a steering box fault, which reduces the driver's control of the vehicle.

  55. Question 55Pre-start checks, vehicle inspection and defects

    An authorised officer issues a major defect notice for a heavy vehicle. What does this generally mean?

    1. The vehicle must be repaired within three months of the notice
    2. The vehicle may only be used for short trips near the depot
    3. The vehicle may be driven normally if the driver carries the notice
    4. The vehicle must not be used until the defect is fixed and the notice cleared Correct answer.

    Explanation

    A major defect notice is issued when the defect is serious enough to stop the vehicle being used. The vehicle must be repaired and the notice cleared before it returns to service.

  56. Question 56Pre-start checks, vehicle inspection and defects

    Under chain of responsibility principles, who is responsible for keeping a heavy vehicle in a safe condition?

    1. Only the driver, because the driver holds the licence
    2. Only the registered owner, because they own the vehicle
    3. Only the workshop that performs scheduled servicing
    4. Everyone in the supply chain, including drivers and operators Correct answer.

    Explanation

    Chain of responsibility obligations apply to parties such as operators, schedulers, consignors and drivers. Each has a role in ensuring the vehicle is maintained and that defects are reported and acted on.

  57. Question 57Pre-start checks, vehicle inspection and defects

    A front tyre shows heavy wear on the outer edge while the rest of the tread is even. What is the most likely cause?

    1. The tyre has recently been replaced with a new one
    2. Wheel alignment or suspension geometry is out of adjustment Correct answer.
    3. The wheel bearings on that side have failed completely
    4. The tyre has been run at too low a pressure on that wheel

    Explanation

    Wear concentrated on one edge points to a geometry problem such as incorrect toe or camber. The cause should be corrected before a new tyre is fitted, or it will wear the same way.

  58. Question 58Pre-start checks, vehicle inspection and defects

    With the engine off and the air system charged, you watch the pressure gauge fall steadily over a few minutes. What does this indicate?

    1. The brake chambers are fully charged and holding
    2. The compressor has cut in to maintain pressure
    3. The gauge is showing normal behaviour for a parked vehicle
    4. There is a leak in the air system that must be repaired Correct answer.

    Explanation

    Once the system is charged and the engine is off, pressure should stay steady. A steady fall shows a leak, which can reduce braking performance and must be traced and fixed.

  59. Question 59Pre-start checks, vehicle inspection and defects

    After moving off in a heavy rigid vehicle, when should the driver test the brakes?

    1. Only when the vehicle is fully loaded
    2. At low speed, in a safe spot before entering traffic Correct answer.
    3. At the end of the trip, before parking
    4. Whenever the vehicle reaches highway speed

    Explanation

    A low-speed brake test confirms the brakes respond evenly and the vehicle pulls up straight before the driver commits to traffic. Any pull, delay or noise indicates a fault that should be checked.

  60. Question 60Pre-start checks, vehicle inspection and defects

    What is the correct way to check the engine oil level on a heavy rigid vehicle?

    1. Engine idling on level ground, reading the dipstick without wiping it first.
    2. Straight after engine shutdown, with the vehicle parked on a slope, reading the dipstick.
    3. Engine off, level ground: wipe the dipstick, refit it fully, then read the level. Correct answer.
    4. Engine off, but only when the oil is cold, reading the dipstick once only.

    Explanation

    Oil drains back into the sump once the engine stops, so the dipstick is only accurate on level ground after a short wait. Wiping and refitting the stick gives a clean reading between the low and full marks.

  61. Question 61Pre-start checks, vehicle inspection and defects

    What is the minimum legal tread depth for the tyres fitted to a heavy rigid vehicle?

    1. 2.5 mm in the centre grooves only
    2. 3.0 mm on the steer tyres only
    3. 1.5 mm across the tread Correct answer.
    4. 1.0 mm across the whole tread

    Explanation

    Road rules set a minimum of 1.5 mm of tread across the width of the tyre for heavy vehicles. Below that figure the tyre is defective and must be replaced, because tread is what clears water and maintains grip.

  62. Question 62Pre-start checks, vehicle inspection and defects

    Before moving a heavy rigid vehicle away from the kerb, why should the driver walk around it first?

    1. To check blind spots for people, animals or objects. Correct answer.
    2. To confirm the fuel gauge reading matches the logbook.
    3. To let the engine idle long enough to build oil pressure.
    4. To allow the brakes to cool after the previous trip.

    Explanation

    Heavy vehicles have large blind areas immediately in front, beside the cab and behind the body. A short walk-around before moving off is the only reliable way to confirm that no person, animal or object is in the path of the vehicle.

  63. Question 63Pre-start checks, vehicle inspection and defects

    Why is moisture drained from the air reservoirs during the daily inspection?

    1. To reduce the pressure needed to release the parking brake.
    2. To prevent water corroding valves and brake components. Correct answer.
    3. To increase the volume of air the compressor can store.
    4. To stop the compressor from cutting in too often.

    Explanation

    Compressed air carries water vapour that condenses inside the reservoirs. If the tanks are not drained daily, the water corrodes them and travels through the system to valves and brake chambers, causing sluggish or failed braking.

  64. Question 64Pre-start checks, vehicle inspection and defects

    At start-up, one of the dash warning lamps fails to illuminate during the self-test. What should you do?

    1. Ignore it; the self-test is only a courtesy display.
    2. Treat it as a defect: the globe or circuit may have failed. Correct answer.
    3. Rev the engine hard to see whether the lamp flickers on.
    4. Note it in the logbook at the end of the week and keep driving.

    Explanation

    The self-test proves that each warning lamp and its wiring actually works. If a lamp does not light, a genuine fault later would go unnoticed, so the vehicle should be reported and the lamp repaired before it is used.

  65. Question 65Pre-start checks, vehicle inspection and defects

    During the pre-start check you find a deep cut exposing cords in the sidewall of a steer tyre. What is the correct action?

    1. Reduce speed and monitor the tyre during the trip.
    2. Record it as a minor defect and continue the run.
    3. Take the vehicle out of service and have the tyre replaced. Correct answer.
    4. Move the tyre to a trailer position where it carries less load.

    Explanation

    A cut that exposes the cords means the structure of the tyre is compromised and it can fail without warning. This is a major defect, so the vehicle must not be driven until the tyre is replaced.

  66. Question 66Pre-start checks, vehicle inspection and defects

    When is the correct time to check and top up the engine coolant?

    1. Straight after a long climb, while the thermostat is open.
    2. Whenever the level looks low, with the engine at operating temperature.
    3. Only when the temperature gauge reads above normal.
    4. When the engine is cold, using the correct coolant mix. Correct answer.

    Explanation

    Coolant expands when hot and the system is under pressure, so a hot check gives a false reading and opening the cap can release scalding fluid. The level is checked and topped up with the correct mix only when the engine is cold.

  67. Question 67Pre-start checks, vehicle inspection and defects

    After a short run you touch each wheel hub and find one much hotter than the others. What does this most likely indicate?

    1. The tyre on that wheel is correctly inflated.
    2. The wheel bearings have been recently repacked.
    3. A dragging brake or failing wheel bearing. Correct answer.
    4. The load is sitting slightly toward that side.

    Explanation

    Heat at the wheel end is generated by friction. A hub running noticeably hotter than its neighbours points to a brake that is not releasing fully or a bearing that is failing, either of which can lead to a wheel-end fire or wheel loss.

  68. Question 68Pre-start checks, vehicle inspection and defects

    The engine drive belt shows a glazed, shiny surface with small cracks. What does this suggest?

    1. The belt is over-lubricated and needs cleaning.
    2. The belt has been recently replaced and is bedding in.
    3. The belt is worn and slipping, and should be replaced. Correct answer.
    4. The belt is correctly tensioned and running normally.

    Explanation

    Glazing is produced by a belt slipping on its pulleys and by heat, while cracking shows the rubber has aged. Together they mean the belt can fail and take the alternator, water pump or cooling fan with it.

  69. Question 69Load restraint and load security

    Under the load restraint performance standards, a load on a heavy vehicle must be restrained against a forward force equal to what proportion of the load's weight?

    1. 0.8 of its weight Correct answer.
    2. 0.2 of its weight
    3. 1.0 of its weight
    4. 0.5 of its weight

    Explanation

    The load restraint performance standards require restraint against a forward force of 0.8g, which is 0.8 times the load's weight. The other directions have different requirements: 0.5g backward, 0.5g sideways and 0.2g upward.

  70. Question 70Load restraint and load security

    A tarpaulin is fitted over a load. What does this achieve?

    1. It restrains the load against forward movement
    2. It provides lateral restraint
    3. It increases friction between the load and the tray
    4. It protects the load from weather but is not a restraint Correct answer.

    Explanation

    A tarpaulin is a cover for weather protection and does not have a rated restraint capacity. The load must still be restrained by rated lashings, containment or other suitable means.

  71. Question 71Load restraint and load security

    What is the load restraint status of the curtains on a standard curtainsider?

    1. They provide weather protection only Correct answer.
    2. They replace the need for lashings
    3. They are rated to restrain the full load
    4. They can restrain loads if tied down

    Explanation

    Unless the curtain system is specifically rated as a load restraint, it provides weather protection only. The load inside must be restrained by rated lashings, load containment or other suitable equipment.

  72. Question 72Load restraint and load security

    When should you check that a load is secure?

    1. Before departure and again during the trip Correct answer.
    2. Only before leaving the loading site
    3. Only after the first 500 km
    4. Only if the load looks unstable

    Explanation

    Load restraints can loosen once the vehicle is moving, so the load must be checked before departure and again during the trip. Re-check after rough roads, heavy braking or any sign of load movement.

  73. Question 73Load restraint and load security

    A load on your truck must not obstruct which of the following?

    1. The vehicle's lights, mirrors and number plate Correct answer.
    2. The manufacturer's badge
    3. The fuel filler cap
    4. The cabin air vents

    Explanation

    A load must not obscure the vehicle's lights, mirrors or number plate, because these are needed for safe operation and legal identification. The load must also be secured so it cannot fall or shift.

  74. Question 74Load restraint and load security

    You find a webbing strap with a deep cut through the fibres. What should you do?

    1. Shorten it with a knot
    2. Remove it from service Correct answer.
    3. Tape over the cut
    4. Use it only for light loads

    Explanation

    A strap with cut or damaged fibres has reduced strength and must be removed from service. Knots and tape do not restore the rated capacity of damaged webbing.

  75. Question 75Load restraint and load security

    What is the main purpose of a headboard on a heavy vehicle?

    1. To improve rear visibility
    2. To protect the cabin from forward load movement Correct answer.
    3. To secure the tailgate
    4. To increase the vehicle's payload

    Explanation

    A headboard is a strong barrier behind the cabin that helps restrain forward load movement. It protects the cabin and occupants if the load shifts forward during braking.

  76. Question 76Load restraint and load security

    A load carried on a flat tray must be...

    1. Allowed to overhang the sides if flagged
    2. Held only by its own weight
    3. Contained within the vehicle or restrained so it cannot fall Correct answer.
    4. Stacked above the headboard for visibility

    Explanation

    The load must be contained within the vehicle or restrained so that it cannot fall, shift or be blown off. Restraint cannot rely on the load's own weight alone.

  77. Question 77Load restraint and load security

    What distinguishes direct restraint from tie-down restraint?

    1. Direct restraint uses only friction
    2. Direct restraint uses the vehicle's sides
    3. Direct restraint attaches to the load itself Correct answer.
    4. Direct restraint is only for bulk loads

    Explanation

    Direct restraint connects the load directly to rated attachment points on the vehicle, such as by straps around the load. Tie-down restraint clamps the load against the deck and relies largely on friction.

  78. Question 78Load restraint and load security

    Where should a lashing be attached on a heavy vehicle?

    1. To the fuel tank bracket
    2. To the mudguard stay
    3. To a rated lashing point or chassis member designed for it Correct answer.
    4. To the brake air lines

    Explanation

    Lashings must be attached to rated lashing points or chassis members designed to carry the restraint force. Fuel tank brackets, air lines and mudguards are not rated load restraint points.

  79. Question 79Load restraint and load security

    After tensioning a load binder (dog), what should you do?

    1. Secure the handle with a wire or tie Correct answer.
    2. Tape the handle to the chain
    3. Leave the handle free to move
    4. Loosen it half a turn

    Explanation

    An over-centre load binder handle can open if it is bumped or vibrates, so it should be secured with a wire or tie. The lashing tension should then be checked during the trip.

  80. Question 80Load restraint and load security

    How should you restrain a load of steel pipes that could roll?

    1. By placing them on the tailgate
    2. By stacking them above the headboard
    3. With chocks or wedges and lashings Correct answer.
    4. With a tarpaulin only

    Explanation

    Round loads such as pipes need chocks, wedges or stanchions to prevent rolling, plus lashings to hold them against movement. A tarpaulin does not prevent rolling.

  81. Question 81Load restraint and load security

    Where should the heaviest items in a mixed load be placed?

    1. On top of lighter items
    2. Low down and evenly distributed Correct answer.
    3. At the rear of the tray
    4. Against the tailgate

    Explanation

    Heavy items should be placed low down and distributed evenly to keep the centre of gravity low and within axle mass limits. Placing heavy items high or at the rear can reduce stability and handling.

  82. Question 82Load restraint and load security

    A pallet of boxes is wrapped in plastic film. Is this enough to restrain it?

    1. Yes, if the film is tight
    2. No, unless the pallet is wooden
    3. No, it only unitises the load Correct answer.
    4. Yes, for loads under 500 kg

    Explanation

    Stretch wrap holds items together on the pallet but does not attach the pallet to the vehicle. The pallet still needs rated lashings, containment or other suitable restraint.

  83. Question 83Load restraint and load security

    A load is pressed against the vehicle's side gates. What should you check?

    1. That the tailgate is open
    2. That the load is above the gate height
    3. That the gates are painted
    4. That the gates are rated to contain the lateral load Correct answer.

    Explanation

    Side gates can help contain a load only if they are strong enough and rated for the lateral force. Otherwise, rated lashings or other restraint must control sideways movement.

  84. Question 84Load restraint and load security

    After travelling over a rough road, what should you do?

    1. Lower the tyre pressures
    2. Remove the tarpaulin
    3. Re-check and retension load restraints Correct answer.
    4. Speed up to leave the rough section

    Explanation

    Rough roads and vibration can loosen lashings and allow the load to settle. Stop in a safe place and re-check the load and retension the restraints as needed.

  85. Question 85Load restraint and load security

    Several separate items are carried on one tray. How should they be restrained?

    1. Only the largest item needs restraint
    2. They can be held by one strap over all items
    3. Each item must be restrained or contained Correct answer.
    4. Only the rear item needs restraint

    Explanation

    Each separate item must be restrained or contained so it cannot move independently. One strap over several items may not secure every item, especially if they differ in size or shape.

  86. Question 86Load restraint and load security

    Why is a load with a high centre of gravity more dangerous?

    1. It increases fuel consumption
    2. It reduces braking distance
    3. It improves traction
    4. It makes the vehicle more likely to roll over Correct answer.

    Explanation

    A high centre of gravity reduces stability and makes the vehicle more likely to roll over, particularly when cornering or under sideways load forces. Heavy items should be placed low and the load restrained against movement.

  87. Question 87Load restraint and load security

    Before releasing load restraints during unloading, what should you confirm?

    1. That the tarpaulin is removed
    2. That the load is stable and cannot fall Correct answer.
    3. That the engine is off
    4. That the tailgate is closed

    Explanation

    Releasing restraints can allow an unstable load to fall, so make sure the load is stable and supported before removing lashings. Use props or equipment where needed.

  88. Question 88Load restraint and load security

    What does the lashing capacity (LC) marked on a strap indicate?

    1. The weight of the strap
    2. The length of the strap
    3. The maximum load it can restrain in all directions
    4. The maximum force the strap can carry Correct answer.

    Explanation

    Lashing capacity is the maximum force the lashing is rated to carry, not the weight of the load it can secure. The restraint effect also depends on the lashing angle, friction and how the lashing is attached.

  89. Question 89Load restraint and load security

    A load rests on a steel tray with a friction factor of 0.4. For a 1,000 kg load, what forward restraining force does friction provide? (Take g = 10 m/sยฒ)

    1. 8 kN
    2. 10 kN
    3. 0.4 kN
    4. 4 kN Correct answer.

    Explanation

    Friction force equals the friction factor multiplied by the load's weight. The weight is 1,000 kg ร— 10 m/sยฒ = 10 kN, so friction provides 0.4 ร— 10 kN = 4 kN. The forward standard is 8 kN, so additional restraint would be needed.

  90. Question 90Load restraint and load security

    Why does a lashing fitted at a shallow angle give less effective restraint than one at a steeper angle?

    1. It increases friction
    2. It is always longer
    3. It has a smaller component acting in the required direction Correct answer.
    4. It has a higher lashing capacity

    Explanation

    Only the component of the lashing force acting in the required direction contributes to restraint. A shallow angle gives a smaller useful component, so more lashings or a different arrangement may be needed.

  91. Question 91Load restraint and load security

    Two lashings, each with a lashing capacity of 2,000 kg, are used to directly restrain a load. What is their combined lashing capacity?

    1. 4,000 kg Correct answer.
    2. 2,000 kg
    3. 1,000 kg
    4. 8,000 kg

    Explanation

    The combined lashing capacity is the sum of the individual capacities, so 2,000 kg plus 2,000 kg equals 4,000 kg. The actual restraint effect also depends on angles, attachment and friction.

  92. Question 92Load restraint and load security

    Load restraint standards require a load to be restrained against what upward (vertical) force?

    1. 0.8g
    2. 1.0g
    3. 0.2g Correct answer.
    4. 0.5g

    Explanation

    The performance standards include an upward force requirement of 0.2g to help prevent the load from lifting or bouncing. Forward is 0.8g, while backward and sideways are 0.5g.

  93. Question 93Load restraint and load security

    A load shifts during travel. What is the safest immediate action?

    1. Stop safely and re-secure the load Correct answer.
    2. Ask a passenger to hold it
    3. Speed up to stabilise it
    4. Continue to the nearest town

    Explanation

    If a load shifts, stop safely as soon as possible and re-secure it before continuing. Continuing with a shifted load risks further movement, vehicle instability or the load falling.

  94. Question 94Load restraint and load security

    What is the main job of a load restraint system?

    1. To stop the load moving on the vehicle Correct answer.
    2. To keep the load dry in bad weather
    3. To make the vehicle look tidy on the road
    4. To reduce fuel consumption on long trips

    Explanation

    A load restraint system must hold the load against forces such as braking, acceleration, cornering and bumps. Keeping cargo dry or tidy is not its purpose. The system must prevent movement in every direction, not just backwards or forwards.

  95. Question 95Load restraint and load security

    Why should you avoid tying a knot in a webbing strap?

    1. It stops the ratchet from locking properly
    2. It increases the strap's lashing capacity
    3. It can cut the strap's strength significantly Correct answer.
    4. It makes the strap too short to reach the anchor point

    Explanation

    A knot concentrates force and bends the fibres sharply, which can reduce a webbing strap's strength by a large amount. A strap should run as straight as possible between the anchor point and the load. If a strap is too long, the excess should be secured rather than knotted.

  96. Question 96Load restraint and load security

    Which defect makes a transport chain unfit for use?

    1. A thin film of oil on the chain
    2. Worn paint on the chain
    3. Light surface rust on the links
    4. A cracked or deformed link Correct answer.

    Explanation

    A cracked, bent, stretched or otherwise deformed link can fail suddenly under load. Surface rust, missing paint or oil are cosmetic unless they hide deeper damage. Any chain with a damaged link must be taken out of service.

  97. Question 97Load restraint and load security

    A steel load on a steel tray keeps sliding even though the lashings are correctly tensioned. What is the best fix?

    1. Fit rubber matting under the load Correct answer.
    2. Tighten the lashings well beyond their rated tension
    3. Drape a tarpaulin over the load
    4. Reduce speed and check the load more often

    Explanation

    Steel on steel has very low friction, so the load slides easily even when the lashings are tight. A high-friction layer such as rubber matting or timber dunnage increases the force needed to move the load. Over-tensioning lashings does not solve low friction and can damage the equipment.

  98. Question 98Load restraint and load security

    How should a forklift be secured for transport on a flat tray?

    1. Chain the forks together and allow the wheels to sit free on the tray surface
    2. Rely on the forklift's own parking brake and leave the wheels unchocked during transport
    3. Lower the forks, apply the parking brake, chock the wheels and lash the chassis Correct answer.
    4. Lash the mast to the headboard and leave the transmission in neutral so it can roll slightly

    Explanation

    Plant with wheels must be prevented from rolling and from moving as a whole. Lowering the forks, applying the parking brake, chocking the wheels and lashing the chassis achieves both. Lashing only the mast or relying on the machine's brake leaves the body free to move.

  99. Question 99Load restraint and load security

    How should a load of loose gravel be carried?

    1. Contain it within the body sides and cover it with a tarpaulin Correct answer.
    2. Leave it uncovered so the driver can see if it shifts
    3. Cover it with a tarpaulin and rely on the weight to hold it
    4. Load it above the sides to allow for settling

    Explanation

    Loose bulk material must be contained by the body sides and covered so it cannot spill or blow out. Weight alone does not stop material from shifting or escaping. The cover also protects other road users from falling stones.

  100. Question 100Load restraint and load security

    Why are load tension indicators used on lashings?

    1. To record the distance travelled with the load
    2. To show the direction of travel of the vehicle
    3. To show whether a lashing is at the correct tension Correct answer.
    4. To measure the weight of the load being carried

    Explanation

    A tension indicator gives a visible reading of how tight a lashing is. This helps the driver confirm that the restraint has been tensioned correctly rather than guessed. Correct tension matters because both slack and over-tightened lashings reduce load security.

  101. Question 101Load restraint and load security

    What is the risk of attaching a lashing to an anchor point that is not rated for the load?

    1. The vehicle's suspension will absorb the extra force safely
    2. The anchor point may fail Correct answer.
    3. The load will gradually become lighter as the vehicle travels
    4. The lashing will automatically tighten itself to compensate for the weak point

    Explanation

    Every attachment point must be strong enough for the force the lashing will apply to it. An unrated or unsuitable point can tear or break under load, releasing the lashing completely. The rating of the anchor point is as important as the rating of the strap or chain.

  102. Question 102Load restraint and load security

    Why should you avoid using one lashing to secure two separate items?

    1. If one item moves, the lashing can loosen on the other Correct answer.
    2. It doubles the lashing capacity applied to each item
    3. It makes the lashing impossible to tension correctly at any time
    4. It prevents the ratchet handle from being opened

    Explanation

    A lashing shared between two items couples their movement. If one item shifts or settles, tension can be lost on the other, leaving both inadequately restrained. Each item should be secured so that it is independently held in place.

  103. Question 103Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When driving a heavy rigid vehicle in good, dry conditions, what minimum following distance should you keep behind the vehicle in front?

    1. Two seconds
    2. Half a second for every metre of your vehicle's length
    3. One second
    4. Four seconds Correct answer.

    Explanation

    Heavy vehicles need a longer gap than cars because their mass makes them much harder to stop. The guidance for heavy vehicles in good conditions is a minimum of four seconds, which at 60 km/h is roughly 67 metres of road.

  104. Question 104Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When should you select a lower gear for a long, steep descent?

    1. At the bottom, so the vehicle is ready for the next corner
    2. Before the vehicle starts down the descent Correct answer.
    3. Only once the service brakes begin to fade
    4. While travelling down the descent, once speed has built up

    Explanation

    Engine braking can only control speed if the lower gear is already engaged when the descent begins. Changing down partway down a steep grade risks over-revving the engine and losing control while the vehicle is gaining speed.

  105. Question 105Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Brake fade on a heavy vehicle is mainly caused by:

    1. Water soaking into the brake linings
    2. Heat from continuous or repeated braking Correct answer.
    3. Loose wheel bearings on the front axle
    4. Low tyre pressure on the drive axle

    Explanation

    Brake fade occurs when drums and linings become so hot that friction drops away and the pedal seems to do less and less. It is produced by dragging the brakes or using them repeatedly instead of relying on a low gear and engine braking.

  106. Question 106Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    What is the main benefit of using a retarder or engine brake on a long descent?

    1. It increases the weight carried on the drive axle
    2. It slows the vehicle without heating the service brakes Correct answer.
    3. It allows the vehicle to be driven faster down the slope
    4. It shortens the time needed to change gears

    Explanation

    A retarder or engine brake absorbs energy through the engine or driveline, so the service brakes stay cool and remain available for an emergency. This is why a low gear plus retarder is the standard technique for long grades.

  107. Question 107Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Approaching a bend in a heavy rigid vehicle, you should:

    1. Coast through with the clutch pedal pressed in
    2. Accelerate into the bend, then brake on the exit
    3. Brake firmly in the middle of the bend
    4. Reduce speed before the bend and hold a steady speed through it Correct answer.

    Explanation

    Speed should be sorted out on the straight approach so that only gentle, steady inputs are needed in the curve. Braking hard while turning uses up tyre grip that is already needed to hold the vehicle on its path.

  108. Question 108Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Where should the heaviest part of a load be placed on a rigid truck?

    1. Along the side of the tray away from the driver
    2. As low as possible and evenly spread within axle limits Correct answer.
    3. Over the rear axle only, regardless of the load limits
    4. As high as possible against the headboard

    Explanation

    Keeping mass low and centred lowers the centre of gravity, which reduces rollover risk in turns. Spreading it within the permitted axle loads also keeps steering and braking balanced.

  109. Question 109Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    How does carrying a heavy load affect the stopping distance of a rigid truck?

    1. It increases the stopping distance Correct answer.
    2. It shortens the stopping distance by improving traction
    3. It has no effect if the brakes are in good condition
    4. It only makes a difference on wet roads

    Explanation

    More mass means more kinetic energy that the brakes must convert into heat, so a loaded vehicle takes longer to pull up than the same vehicle empty. The effect is present on dry roads too, and it grows with speed.

  110. Question 110Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    What is the main purpose of an anti-lock braking system (ABS) on a heavy vehicle?

    1. To apply the park brake automatically on a slope
    2. To prevent wheel lock-up so you can still steer Correct answer.
    3. To shorten the time taken for the brakes to release
    4. To increase the load capacity of the vehicle

    Explanation

    ABS rapidly releases and reapplies brake pressure so the wheels keep rotating instead of skidding. That retained rotation lets the driver steer around a hazard while braking hard.

  111. Question 111Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    A common rule of thumb for choosing a gear for a long descent is to select:

    1. Neutral, so the engine cannot over-rev
    2. The same gear you would need to climb that grade Correct answer.
    3. The highest gear the vehicle will pull
    4. One gear higher than the gear used on level ground

    Explanation

    Using the climbing gear on the way down gives roughly the same level of engine braking that the grade demanded on the way up. It keeps the vehicle at a controlled speed without relying on the service brakes.

  112. Question 112Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Your service brakes fail on a steep descent. What is the best course of action?

    1. Apply the park brake fully at once and hold it on
    2. Switch off the engine and coast until the vehicle stops
    3. Pump the foot brake hard while holding the clutch in
    4. Downshift, use engine braking and head for a safe run-off Correct answer.

    Explanation

    Changing to a lower gear brings engine braking into play and reduces the speed the vehicle can reach. Aiming for an escape ramp or other run-off gives a controlled way to stop if the remaining braking is not enough.

  113. Question 113Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    How should you adjust your following distance when driving in heavy rain?

    1. Reduce the gap so other vehicles cannot cut in
    2. Follow closely so you can use the other vehicle's tail lights
    3. Keep the same gap but switch on the hazard lights
    4. Add several more seconds to your gap Correct answer.

    Explanation

    Wet roads reduce grip and lengthen stopping distances, so the gap must grow beyond the dry-weather minimum. Adding several seconds gives room for the longer stopping distance and for spray limiting your view.

  114. Question 114Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Another driver pulls in front of you and reduces your following gap. What should you do?

    1. Brake hard to re-open the gap immediately
    2. Flash your headlights and hold your speed
    3. Ease off the accelerator and rebuild the gap gradually Correct answer.
    4. Change lanes to get clear of the vehicle

    Explanation

    The safe response is to restore your own safety margin without creating a new hazard. Easing off lets the gap open smoothly and avoids forcing traffic behind you to react sharply.

  115. Question 115Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When a heavy rigid vehicle turns, the rear wheels:

    1. Follow exactly the path taken by the front wheels
    2. Track wider than the front wheels, but only in a left turn
    3. Swing outside the path taken by the front wheels
    4. Cut inside the path taken by the front wheels Correct answer.

    Explanation

    Because the rear wheels are further from the centre of the turn, they track a tighter path and cut inside the front wheels. This is why you swing wide before a turn and check the mirrors for kerbs and poles on the inside.

  116. Question 116Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Why must speed be reduced well before a curve when the vehicle is carrying a high load?

    1. Because the steering becomes heavier at low speed
    2. Because gears cannot be changed while the vehicle is turning
    3. Because cornering force and rollover risk rise sharply with speed Correct answer.
    4. Because the brakes cool too quickly on a straight road

    Explanation

    The sideways force pushing a vehicle out of a curve increases with the square of speed, so a small increase in speed means a much larger overturning effect. A high load raises the centre of gravity and reduces the margin before a rollover.

  117. Question 117Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    On a long descent with air brakes, the safest way to use the foot brake is to:

    1. Use firm applications, releasing between them to let the brakes cool Correct answer.
    2. Hold light continuous pressure for the whole descent
    3. Keep the transmission in neutral and rely on the foot brake alone
    4. Fan the pedal on and off as rapidly as possible

    Explanation

    Firm applications that slow the vehicle, followed by release, let heat dissipate instead of building continuously. Light continuous drag keeps heat in the drums and is a common route to brake fade.

  118. Question 118Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    If the low air pressure warning sounds while you are driving, you should:

    1. Stop safely as soon as possible and investigate Correct answer.
    2. Increase engine speed and keep driving to recharge the system
    3. Continue to the next town and report it there
    4. Pump the brake pedal repeatedly to build pressure

    Explanation

    A low air warning means the braking system may soon be unable to apply the brakes properly. The vehicle should be brought to a safe stop promptly and the fault found before continuing.

  119. Question 119Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Why must a load be restrained against sideways movement before a trip begins?

    1. It causes the brakes to overheat on long descents
    2. A shifting load can destabilise the vehicle in a turn Correct answer.
    3. It improves traction on the front steering axle
    4. It increases the air pressure in the brake system

    Explanation

    Load restraint keeps the mass where the driver expects it, so weight transfer in a turn or under braking stays predictable. A load that slides can move the centre of gravity suddenly and tip the vehicle over or break the restraints.

  120. Question 120Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When another vehicle is overtaking your heavy rigid vehicle on a two-lane road, you should:

    1. Move towards the centre of the road to give room
    2. Hold a steady speed and keep well to the left Correct answer.
    3. Flash your headlights at oncoming traffic
    4. Speed up so the overtaking move is finished sooner

    Explanation

    Holding a steady speed and keeping left makes the overtaking move as short and predictable as possible. Speeding up forces the other driver to stay on the wrong side of the road for longer.

  121. Question 121Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    If a front tyre blows out at highway speed, you should:

    1. Turn the steering wheel sharply towards the shoulder
    2. Accelerate briefly to steady the vehicle
    3. Brake as hard as possible straight away
    4. Grip the wheel firmly, keep straight and slow gradually Correct answer.

    Explanation

    A blown front tyre pulls the steering, so the priority is a firm grip and small corrections to hold a straight line. Speed should then be reduced gently, because hard braking or sharp steering can send the vehicle out of control.

  122. Question 122Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Your vehicle begins to aquaplane on a wet road. The correct response is to:

    1. Brake firmly to regain grip
    2. Accelerate to push through the water
    3. Steer sharply to find a drier line
    4. Ease off the accelerator and avoid sudden inputs Correct answer.

    Explanation

    Aquaplaning means the tyres are riding on water rather than the road, so grip returns only as speed falls and the water clears. Gentle deceleration with the steering held steady lets the tyres regain contact without a skid.

  123. Question 123Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Why should an engine brake or retarder be used with care on a wet or slippery road?

    1. It disengages the transmission automatically
    2. Braking force at the drive wheels can cause a skid Correct answer.
    3. It reduces the air pressure available for the brakes
    4. It overheats the service brakes faster than foot braking

    Explanation

    Retarders act on the drive axle, and on a low-grip surface that braking force can break traction at the rear wheels. On slippery roads the retarder setting should be reduced or switched off so the wheels keep grip.

  124. Question 124Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Why is coasting in neutral down a long hill dangerous in a heavy vehicle?

    1. The differential will overheat at high road speed
    2. The engine will stall and the steering will lock up
    3. With no engine braking, the service brakes must absorb all the energy Correct answer.
    4. The speedometer stops working so speed cannot be checked

    Explanation

    In neutral the engine cannot hold the vehicle back, so all of the energy of the descent has to be turned into heat by the service brakes. That quickly leads to fade and leaves nothing in reserve if an emergency stop is needed.

  125. Question 125Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    A heavy vehicle travelling at 60 km/h covers about 17 metres every second. If the driver's reaction time is 1.5 seconds, roughly how far does the vehicle travel before the brakes begin to work?

    1. About 25 metres Correct answer.
    2. About 17 metres
    3. About 40 metres
    4. About 10 metres

    Explanation

    Reaction distance is speed multiplied by reaction time, so about 17 metres per second times 1.5 seconds equals roughly 25 metres. This distance is travelled at full speed and comes before any braking effect at all.

  126. Question 126Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Which of these most increases the risk of a rollover when cornering a loaded rigid truck?

    1. A high centre of gravity plus speed in the bend Correct answer.
    2. Tyre pressures that are checked and correct before departure
    3. A steady speed that is held right through a sweeping bend
    4. A load that is spread evenly and secured as low as possible

    Explanation

    Rollover risk depends on how high the mass sits and how much sideways force is generated in the turn. A tall, heavy load combined with speed produces a large overturning effect that the tyres may not be able to resist.

  127. Question 127Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    You are approaching a long, steep climb fully loaded. What is the best technique?

    1. Build up as much speed as possible, even above the limit
    2. Stay in the highest gear and let speed fall as far as it will
    3. Change down before the engine starts to labour and lose speed Correct answer.
    4. Change down only once the engine is almost stalling

    Explanation

    Changing down early keeps the engine in its power band and avoids losing momentum that cannot be regained on the grade. It also means the shift happens at a controlled speed rather than during a labouring crawl.

  128. Question 128Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Brake fade on a long descent is caused by:

    1. heat building up in the brake drums or discs Correct answer.
    2. gravel becoming trapped between the brake shoes
    3. air leaking past the wheel cylinder seals
    4. the engine turning over at high revolutions

    Explanation

    Braking converts the vehicle's movement into heat in the drums or discs and linings. If the brakes are used continuously down a long hill, that heat builds faster than it can escape, friction drops and the brakes become progressively less effective. This loss of performance is brake fade.

  129. Question 129Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Why is a safe following distance usually measured in seconds rather than in metres?

    1. Because speedometers show seconds as well as kilometres per hour
    2. Because the gap automatically adjusts as your speed changes Correct answer.
    3. Because the length of a vehicle in metres varies with the load it is carrying
    4. Because metres cannot be judged accurately from a high driving position

    Explanation

    A time gap stays valid at any speed, because the distance covered in that time grows as the vehicle goes faster. Counting seconds behind the vehicle in front therefore keeps the same safety margin whether you are in a 60 km/h zone or on a highway.

  130. Question 130Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    What is the main benefit of using an exhaust brake or retarder on a long descent?

    1. It increases the maximum load the vehicle is allowed to carry
    2. It holds speed with less use of the service brakes Correct answer.
    3. It gives the front tyres more grip on loose gravel surfaces
    4. It allows the transmission to be left in neutral on the descent

    Explanation

    An exhaust brake or retarder uses engine or driveline resistance to hold the vehicle back on a descent. Because the wheel brakes are used far less, they stay cool and remain fully effective if you need to stop quickly.

  131. Question 131Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    Compared with a hydraulic braking system, the brakes on an air-braked heavy vehicle:

    1. apply a moment after the pedal is pressed Correct answer.
    2. cannot be applied or released gradually by the driver
    3. respond instantly, with no delay at all between pedal and brake
    4. apply only after the engine has been switched off completely

    Explanation

    In an air system, compressed air must travel through the lines and build pressure at each brake chamber before the brakes apply. This creates a slight lag, so a driver of an air-braked vehicle must begin braking a little earlier than in a car.

  132. Question 132Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    You are approaching a bend in a loaded rigid truck. Where should most of the braking be done?

    1. While the vehicle is in the middle of the bend
    2. Before the vehicle enters the bend Correct answer.
    3. Just as the vehicle begins to accelerate out of the bend
    4. Only after the front wheels have straightened up again

    Explanation

    Tyres have a limited amount of grip, and braking and cornering both draw on it. Slowing before the bend means you enter it at a safe speed with grip in reserve for steering, rather than asking the tyres to do two jobs at once.

  133. Question 133Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    You are already part-way down a steep hill and the vehicle is gaining speed in a high gear. What should you do?

    1. Change to a much lower gear immediately to slow the vehicle down
    2. Brake firmly to reduce speed, then select a lower gear Correct answer.
    3. Select neutral briefly so that the change down is smoother
    4. Keep the gear and rely on the brakes for the rest of the hill

    Explanation

    Forcing a big downshift while the vehicle is already travelling fast can over-rev the engine and upset the rear wheels. The correct sequence is to use the brakes to bring the speed back to a safe level, then engage the lower gear so engine braking holds that speed.

  134. Question 134Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When you brake hard in a heavy rigid vehicle, weight shifts forward. What is the main consequence for the tyres?

    1. The rear tyres grip more and the front tyres grip less
    2. The front tyres grip more and the rears can lock Correct answer.
    3. All four tyres share the load evenly, so grip is unchanged
    4. The front tyres are more likely to lock and the rear tyres grip more

    Explanation

    Hard braking transfers load onto the front axle, which increases grip at the front while the rear axle becomes lighter. A lightly loaded rear axle has less grip and its wheels can lock or begin to skid, which is why braking should be progressive.

  135. Question 135Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    How does the outward force on a vehicle in a curve change if the driver doubles the speed through the same curve?

    1. It doubles, because speed and force rise together
    2. It becomes four times as great Correct answer.
    3. It stays the same because the radius of the curve has not changed
    4. It increases by about half again as much as before

    Explanation

    The outward, or centrifugal, force in a curve increases with the square of the speed. Doubling the speed therefore multiplies that force by four, which is why a bend taken comfortably at low speed can push a heavy vehicle towards a skid or rollover at higher speed.

  136. Question 136Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

    When is a sealed road usually most slippery for a heavy vehicle?

    1. When light rain first falls after a long dry spell Correct answer.
    2. After several hours of steady, heavy rain have fallen
    3. After the road has been swept and is completely dry
    4. On a hot, dry day when no rain has fallen for weeks

    Explanation

    During dry weather, oil, rubber and dust build up on the road surface. The first light rain mixes with these deposits to form a slippery film, and grip is poor until heavier rain washes the surface clean.

  137. Question 137Road rules, signage and sharing the road safely

    In Victoria, what is the default speed limit on a road in a built-up area where no speed limit sign is displayed?

    1. 70 km/h
    2. 60 km/h
    3. 50 km/h Correct answer.
    4. 40 km/h

    Explanation

    Where no sign shows a different limit, a road in a built-up area has a default limit of 50 km/h. The limit applies along the whole road until a sign shows something different.

  138. Question 138Road rules, signage and sharing the road safely

    In Victoria, what speed limit applies in a school zone while the zone is operating?

    1. 40 km/h Correct answer.
    2. 30 km/h
    3. 50 km/h
    4. 25 km/h

    Explanation

    School zones in Victoria operate at 40 km/h during the posted times on school days, usually 8:00โ€“9:30 am and 2:30โ€“4:00 pm. The lower limit protects children moving near the school.

  139. Question 139Road rules, signage and sharing the road safely

    When you approach a stop sign at an intersection, what must you do?

    1. Slow to walking pace and continue if the way is clear
    2. Sound your horn before moving off
    3. Come to a complete stop at the stop line, then give way Correct answer.
    4. Stop only if another vehicle is approaching

    Explanation

    A stop sign requires the vehicle to come to a complete stop at the stop line, or at the edge of the intersection if no line is painted. You then give way to all traffic before proceeding.

  140. Question 140Road rules, signage and sharing the road safely

    You are approaching a railway level crossing and the red lights begin to flash. What must you do?

    1. Stop only if a train is in sight
    2. Slow down and check before crossing
    3. Proceed carefully if the boom gates have not started to lower
    4. Stop until the lights stop flashing Correct answer.

    Explanation

    Flashing red lights at a level crossing mean you must stop and stay stopped. You may only proceed once the lights stop flashing and the crossing is clear.

  141. Question 141Road rules, signage and sharing the road safely

    A circular sign showing a U-shaped arrow with a red diagonal line through it means:

    1. U-turns are not permitted Correct answer.
    2. One-way road ahead
    3. Turn left only
    4. No through road

    Explanation

    A red diagonal slash across a symbol means the manoeuvre shown is prohibited. This sign bans U-turns at that location.

  142. Question 142Road rules, signage and sharing the road safely

    A broken white line painted between two lanes of traffic means:

    1. Overtaking is prohibited
    2. The lane is reserved for buses
    3. You must stay in your lane at all times
    4. You may change lanes when it is safe Correct answer.

    Explanation

    Broken white lines separate lanes travelling in the same direction and may be crossed once you have checked that it is safe. Solid white lines indicate that you should stay within your lane.

  143. Question 143Road rules, signage and sharing the road safely

    At a pedestrian crossing marked by stripes painted on the road, you must give way to:

    1. Any pedestrian on or entering the crossing Correct answer.
    2. Pedestrians only at traffic light crossings
    3. Pedestrians only after they step onto your side of the road
    4. Pedestrians who raise a hand to signal

    Explanation

    Drivers must give way to pedestrians who are on a marked crossing or who are about to enter it. The duty applies whether or not the pedestrian has given any signal.

  144. Question 144Road rules, signage and sharing the road safely

    When entering a roundabout, you must give way to:

    1. Vehicles travelling straight ahead only
    2. Any vehicle that arrives after you
    3. Vehicles approaching from your right only
    4. All vehicles already in the roundabout Correct answer.

    Explanation

    At a roundabout you must give way to any vehicle already in the roundabout, whichever lane it is in. Once inside, you keep to your lane and signal before exiting.

  145. Question 145Road rules, signage and sharing the road safely

    In steady rain, the gap you leave to the vehicle in front should be:

    1. Exactly the same as in dry weather
    2. About one second
    3. At least double your normal dry-weather gap Correct answer.
    4. Slightly shorter so others can merge

    Explanation

    Wet roads increase stopping distances and reduce visibility, so the gap you leave should be at least doubled. A heavy vehicle needs more room again because of its greater mass.

  146. Question 146Road rules, signage and sharing the road safely

    You are driving in a built-up area with a speed limit of 60 km/h and a bus signals to leave a bus stop. What must you do?

    1. Sound your horn and drive past quickly
    2. Give way to the bus if it is safe to do so Correct answer.
    3. Change to the right lane and accelerate
    4. Maintain your speed because you have right of way

    Explanation

    In a built-up area where the limit is 80 km/h or less, you must give way to a bus leaving a bus stop when it is safe to do so. This is a specific road rule that keeps public transport moving.

  147. Question 147Road rules, signage and sharing the road safely

    You are overtaking a cyclist on a road where the speed limit is 70 km/h. What minimum space must you allow?

    1. 1 m
    2. 0.5 m
    3. 1.5 m Correct answer.
    4. About 2 m

    Explanation

    In Victoria drivers must leave at least 1 metre when passing a cyclist at speeds up to 60 km/h, and at least 1.5 metres at higher speeds. In a 70 km/h zone the 1.5 metre minimum applies.

  148. Question 148Road rules, signage and sharing the road safely

    You are approaching a stationary emergency vehicle on the roadside with its flashing lights on. What must you do?

    1. Move into the next lane only if it is clear
    2. Slow to 40 km/h and move over if it is safe Correct answer.
    3. Sound your horn to warn the officers
    4. Continue at the posted speed limit without changing lanes

    Explanation

    Victoria requires drivers to slow to 40 km/h when passing a stationary emergency or enforcement vehicle displaying flashing lights, and to move over where it is safe. This protects people working on the roadside.

  149. Question 149Road rules, signage and sharing the road safely

    The traffic light turns yellow as you approach an intersection. What should you do?

    1. Always continue at the same speed
    2. Stop immediately wherever you are
    3. Accelerate to get through before red
    4. Stop if you can do so safely Correct answer.

    Explanation

    A yellow light means stop unless you are so close to the line that stopping would be unsafe. You must not speed up to beat the red light.

  150. Question 150Road rules, signage and sharing the road safely

    Which option best describes a hook turn at a Melbourne CBD intersection?

    1. Turning left from the right-hand lane at a slip lane
    2. Moving to the left lane, then turning right on the green Correct answer.
    3. Making a U-turn from the middle of the intersection
    4. Driving to the far side and turning right when the light turns red

    Explanation

    In a hook turn you move into the left lane within the intersection and wait there. When the light for the cross street turns green, you complete the right turn.

  151. Question 151Road rules, signage and sharing the road safely

    A tram has stopped ahead of you and passengers are getting on and off. What must you do?

    1. Stop behind the tram until it is safe to pass Correct answer.
    2. Sound your horn and pass slowly
    3. Pass on the left if there is room
    4. Drive around the tram using the tram tracks

    Explanation

    You must stop behind a tram that has stopped to let passengers on or off, and must not pass until the area is clear. Passing a stopped tram endangers people stepping onto the road.

  152. Question 152Road rules, signage and sharing the road safely

    You want to overtake a slower vehicle, but there is a continuous double white line down the centre of the road. What does this mean?

    1. You may cross the lines if you indicate first
    2. You must not cross the lines to overtake Correct answer.
    3. You may cross only if the road is empty
    4. You may cross if the vehicle ahead is very slow

    Explanation

    Double continuous centre lines mean neither direction of traffic may cross them. You must wait until the lines become broken or a signed overtaking lane appears.

  153. Question 153Road rules, signage and sharing the road safely

    You enter a roadworks area where a 40 km/h sign is displayed, but no workers are visible. What should you do?

    1. Sound your horn and continue at the normal limit
    2. Obey the 40 km/h limit until the signs change Correct answer.
    3. Speed up only in the left lane
    4. Return to the normal limit since no work is happening

    Explanation

    A reduced limit through roadworks applies until a sign changes it or an end-of-works sign appears. Workers may be out of sight while hazards such as loose gravel and narrowed lanes remain.

  154. Question 154Road rules, signage and sharing the road safely

    Two lanes merge into one, your lane is ending, and there are no lane lines. What should you do?

    1. Stop and wait for a gap in the other lane
    2. Give way to the vehicle that is ahead of you Correct answer.
    3. Speed up to get in front of the other vehicle
    4. Move across without indicating

    Explanation

    When lanes merge, drivers must give way to the vehicle that is ahead of them, which is known as a zip merge. You should match speed and merge in turn rather than racing to get in front.

  155. Question 155Road rules, signage and sharing the road safely

    A bridge is marked with a clearance sign of 4.6 m. Your rigid truck, fully loaded, is 4.8 m high. What should you do?

    1. Proceed slowly and listen for scraping
    2. Reduce tyre pressure and cross
    3. Cross in the centre of the road for extra room
    4. Take another route Correct answer.

    Explanation

    A clearance sign shows the maximum vehicle height that can pass under the structure. At 4.8 m your truck exceeds the posted 4.6 m, so the crossing must not be attempted.

  156. Question 156Road rules, signage and sharing the road safely

    A 'TRUCKS AND BUSES NOT IN RIGHT LANE' sign on a multi-lane highway means a heavy vehicle:

    1. May use any lane when traffic is heavy
    2. Must keep out of the right lane except to overtake Correct answer.
    3. May use the right lane only when turning left
    4. Must stay in the left-hand lane no matter what the traffic is doing

    Explanation

    The sign keeps slower heavy vehicles out of the right-hand lane so that lighter traffic can overtake safely. You may use the right lane briefly to overtake or to turn right.

  157. Question 157Road rules, signage and sharing the road safely

    A bridge carries a load limit sign showing 10 t. Your rigid truck has a tare mass of 9 t and is carrying 4 t of freight. What is the correct action?

    1. Cross because the sign refers only to the tare mass
    2. Do not cross the bridge Correct answer.
    3. Cross if no other vehicle is on the bridge
    4. Cross at walking pace

    Explanation

    A load limit sign applies to the total mass of the vehicle together with its load. Your vehicle weighs 13 t in total, which exceeds the 10 t limit, so another route must be used.

  158. Question 158Road rules, signage and sharing the road safely

    You are driving on a road that ends at a T-intersection and you want to turn right. Who must give way?

    1. Nobody, because you are turning right
    2. Only traffic approaching from your right
    3. You must give way to traffic on the continuing road Correct answer.
    4. Traffic on the continuing road must always give way to a vehicle turning right

    Explanation

    At a T-intersection the road that ends must give way to traffic on the road that continues through. This applies whether you turn left or right out of the terminating road.

  159. Question 159Road rules, signage and sharing the road safely

    You have just overtaken a long heavy vehicle on a highway. When is it safe to move back into the left lane?

    1. When you can see the truck's headlights in your mirrors Correct answer.
    2. As soon as you have signalled left
    3. As soon as your rear wheels pass the truck's front bumper
    4. When the truck flashes its headlights at you

    Explanation

    You need enough clear space ahead of the truck for the driver to see you and maintain a safe gap. Seeing the truck's headlights in your mirrors is a reliable guide that you are far enough ahead.

  160. Question 160Road rules, signage and sharing the road safely

    You plan to turn right at a roundabout. How should you signal?

    1. Signal left on approach and right when leaving
    2. Signal right on approach, then left as you pass the exit before yours Correct answer.
    3. Signal right on approach and keep signalling until you exit
    4. No signal is needed if the roundabout is empty

    Explanation

    For a right turn you signal right on approach and continue until you are ready to leave the roundabout. You then signal left to show other drivers that you are exiting.

  161. Question 161Road rules, signage and sharing the road safely

    A bus lane sign shows operating times of 7:00โ€“9:00 am and 4:00โ€“6:00 pm, Monday to Friday. When may a heavy vehicle that is not a bus use the lane?

    1. Never, under any circumstances
    2. Outside those times, unless signs say otherwise Correct answer.
    3. At any time if no bus is in sight
    4. Only when carrying passengers

    Explanation

    A bus lane with posted times is reserved for buses only during those hours. Outside them, other vehicles may use the lane, but you should still check for any other restrictions shown on signs.

  162. Question 162Road rules, signage and sharing the road safely

    What is the speed limit in a Victorian school zone when the school zone signs are operating?

    1. 40 km/h Correct answer.
    2. 30 km/h
    3. 50 km/h
    4. 60 km/h

    Explanation

    In Victoria, school zones generally operate at 40 km/h during the times shown on the school zone signs, typically 8:00โ€“9:30 am and 2:30โ€“4:00 pm on school days. The lower limit applies even if no children are visible.

  163. Question 163Road rules, signage and sharing the road safely

    You approach a railway level crossing where the red lights are flashing and the boom gates are starting to lower. What must you do?

    1. Follow the vehicle ahead across
    2. Slow down and cross if no train is visible
    3. Continue across before the gates lower
    4. Stop and wait until the signals stop Correct answer.

    Explanation

    Flashing red lights at a railway level crossing mean you must stop and remain stopped. You may proceed only after the lights stop flashing and the boom gates are fully raised.

  164. Question 164Road rules, signage and sharing the road safely

    On a multi-lane highway with a speed limit of 100 km/h, when may you drive in the right-hand lane?

    1. Only during peak traffic periods
    2. At any time, provided the lane is clear
    3. Only when you are driving a heavy vehicle
    4. When overtaking another vehicle Correct answer.

    Explanation

    On a multi-lane road with a speed limit of 80 km/h or more, you must keep left unless overtaking. The right lane is for overtaking, not for general cruising, even when it is clear.

  165. Question 165Road rules, signage and sharing the road safely

    You are turning left at traffic lights and pedestrians are crossing the road you are turning into. What must you do?

    1. Sound your horn to hurry them
    2. Continue through and steer around them
    3. Give way and wait for them to clear Correct answer.
    4. Edge forward until they stop

    Explanation

    When turning at an intersection, you must give way to pedestrians crossing the road you are turning into. A green light does not override this duty.

  166. Question 166Road rules, signage and sharing the road safely

    A clearway sign shows operating times of 7:00โ€“9:00 am and 4:00โ€“6:00 pm, Monday to Friday. What does this mean for your heavy vehicle?

    1. You must not stop at the kerb during those times Correct answer.
    2. You may stop briefly to load or unload during those times
    3. You may park for up to two hours during those times
    4. You may stop only if you stay with the vehicle

    Explanation

    A clearway means no stopping at the kerb during the times shown, even briefly for loading or unloading. The restriction applies to all vehicles unless a sign says otherwise.

  167. Question 167Road rules, signage and sharing the road safely

    You are turning right at an intersection with no traffic lights or signs. An oncoming vehicle is travelling straight ahead. Who must give way?

    1. The oncoming vehicle, because it is on your right
    2. You, because you are crossing the oncoming traffic path Correct answer.
    3. Neither vehicle, if both are travelling at the speed limit
    4. The oncoming vehicle, because it is turning into your lane

    Explanation

    At an intersection without traffic lights or signs, a driver turning right must give way to oncoming vehicles travelling straight ahead or turning left. You must wait until the oncoming traffic has cleared before completing the turn.

  168. Question 168Road rules, signage and sharing the road safely

    You are driving a heavy vehicle towards an intersection with a painted yellow box. The traffic ahead is queued and your exit from the box is blocked. What should you do?

    1. Enter the box and use the horn to clear traffic
    2. Enter the box only if the light is green
    3. Enter the box and stop behind the queue
    4. Wait before the box until your exit is clear Correct answer.

    Explanation

    A yellow box junction must be kept clear. You should not enter the box unless your exit is clear, even if the traffic light is green, because stopping in the box blocks crossing traffic.

  169. Question 169Fatigue management, work diaries and emergency procedures

    Which of these is a warning sign that you are becoming fatigued?

    1. Feeling cold in the cabin
    2. Feeling hungry between meals
    3. Frequent yawning and sore eyes Correct answer.
    4. Sharper reaction times

    Explanation

    Yawning, sore or heavy eyes, poor concentration and drifting in the lane are classic signs that fatigue is setting in. Fatigue slows your reactions and judgement, so the warning signs should be acted on before you continue driving.

  170. Question 170Fatigue management, work diaries and emergency procedures

    Under standard fatigue hours, what is the longest continuous work period allowed before you must take at least 15 continuous minutes of rest?

    1. 6 hours 30 minutes
    2. 4 hours
    3. 5 hours
    4. 5 hours 30 minutes Correct answer.

    Explanation

    Standard hours require at least 15 continuous minutes of rest within every 5ยฝ hour work period. That means no single stretch of work may run past 5ยฝ hours before a break is taken.

  171. Question 171Fatigue management, work diaries and emergency procedures

    Who is required to fill out a national work diary?

    1. Only drivers who cross state borders
    2. Every driver of a vehicle over 4.5 tonnes
    3. Drivers of fatigue-regulated heavy vehicles Correct answer.
    4. Only drivers carrying dangerous goods

    Explanation

    The work diary obligation applies to drivers of fatigue-regulated heavy vehicles, generally heavy vehicles or combinations with a GVM over 12 tonnes. It does not depend on crossing a border or on the type of load carried.

  172. Question 172Fatigue management, work diaries and emergency procedures

    What is a micro-sleep?

    1. A nap taken in the passenger seat
    2. A short planned nap at a rest area
    3. A night's sleep broken into blocks
    4. A brief sleep you cannot control Correct answer.

    Explanation

    A micro-sleep is an involuntary lapse into sleep lasting only a few seconds, and it can happen with no warning. It is extremely dangerous because the driver has no control over when it occurs.

  173. Question 173Fatigue management, work diaries and emergency procedures

    You have been driving for three hours and begin blinking heavily and drifting in your lane. What should you do?

    1. Drink coffee and keep driving to the next town
    2. Speed up so the trip finishes sooner
    3. Turn up the radio and open a window
    4. Stop at the next safe place and rest Correct answer.

    Explanation

    Blinking heavily and drifting in the lane mean you are already dangerously fatigued. The only effective remedy is to stop somewhere safe and rest or sleep before continuing.

  174. Question 174Fatigue management, work diaries and emergency procedures

    For how long must completed work diary records be kept?

    1. 12 months
    2. 6 months
    3. 3 years Correct answer.
    4. 7 years

    Explanation

    Work diary records and related fatigue records must be kept for at least three years. This allows an authorised officer to check compliance well after the driving was done.

  175. Question 175Fatigue management, work diaries and emergency procedures

    Which of these is counted as work time in your work diary?

    1. A 30-minute meal break
    2. A one-hour break at a roadhouse
    3. Loading your vehicle at a depot Correct answer.
    4. Sleeping in a sleeper berth

    Explanation

    Work time covers all time spent working, including loading, unloading, inspecting, refuelling and cleaning the vehicle as well as driving. Breaks and sleep are recorded as rest, not work.

  176. Question 176Fatigue management, work diaries and emergency procedures

    Your truck breaks down on a busy highway. What should you do first?

    1. Walk to the nearest property for help
    2. Stand behind the truck and wave traffic past
    3. Sit in the cab with the doors locked
    4. Move off the road and use hazard lights Correct answer.

    Explanation

    Getting the vehicle as far off the road as possible and switching on the hazard lights warns other traffic and reduces the chance of a collision. Only after that should you call for help from a safe position away from the traffic.

  177. Question 177Fatigue management, work diaries and emergency procedures

    A rigid truck with a GVM of 10 tonnes tows a trailer with a GVM of 4 tonnes. What is its status under the fatigue rules?

    1. It is fatigue-regulated because the combination exceeds 12 tonnes Correct answer.
    2. It is fatigue-regulated only when carrying dangerous goods
    3. It is not fatigue-regulated because the truck alone is under 12 tonnes
    4. It is not fatigue-regulated because trailers are ignored

    Explanation

    Fatigue rules apply to heavy vehicles and combinations with a GVM over 12 tonnes, so the truck and trailer masses are added together. A 10 tonne truck towing a 4 tonne trailer is a 14 tonne combination and is therefore fatigue-regulated.

  178. Question 178Fatigue management, work diaries and emergency procedures

    Under standard hours, what is the maximum work time allowed in any 24-hour period?

    1. 12 hours Correct answer.
    2. 10 hours
    3. 16 hours
    4. 14 hours

    Explanation

    Standard hours limit work to 12 hours in any 24-hour period. That same 24-hour period must also include at least 7 continuous hours of stationary rest.

  179. Question 179Fatigue management, work diaries and emergency procedures

    Under standard hours, what continuous rest must you have in every 24-hour period?

    1. 5 hours of sleep in a bed
    2. 6 hours of rest in any form
    3. 7 hours of stationary rest Correct answer.
    4. 4 hours of rest anywhere

    Explanation

    Every 24-hour period must include at least 7 continuous hours of stationary rest. This block of rest is what allows the body to recover before the next period of work.

  180. Question 180Fatigue management, work diaries and emergency procedures

    Under standard hours, what is the maximum work time allowed in any 14-day period?

    1. 144 hours Correct answer.
    2. 168 hours
    3. 96 hours
    4. 120 hours

    Explanation

    Standard hours set a limit of 144 hours of work in any 14-day period, alongside a limit of 72 hours in any 7 days. These longer-term limits sit on top of the daily work and rest rules.

  181. Question 181Fatigue management, work diaries and emergency procedures

    What work diary records must you carry in the vehicle?

    1. All sheets for the last 12 months
    2. Today's sheet and the last 28 days Correct answer.
    3. Only today's sheet
    4. Yesterday's sheet and the last 7 days

    Explanation

    A driver must carry the current work diary together with records covering the previous 28 days. This allows an authorised officer to check recent compliance on the spot.

  182. Question 182Fatigue management, work diaries and emergency procedures

    An authorised officer signals you to stop and asks for your work diary. What must you do?

    1. Offer a photocopy instead of the original
    2. Post the diary to the officer within 24 hours
    3. Hand the diary over for inspection Correct answer.
    4. Refuse until your employer gives permission

    Explanation

    Drivers must produce their work diary when asked by an authorised officer such as a police officer or an NHVR inspector. Failing to produce the diary without a reasonable excuse is an offence.

  183. Question 183Fatigue management, work diaries and emergency procedures

    Your work diary shows a rest break you did not actually take. What is your position under the law?

    1. It only becomes a problem if there is a crash
    2. It is acceptable if no one was hurt
    3. It is an offence you can be prosecuted for Correct answer.
    4. It is a minor issue that only affects your employer

    Explanation

    Work diary entries must be accurate, and deliberately recording a rest you did not take is a false entry and an offence. Officers rely on these records to check that fatigue rules are being followed.

  184. Question 184Fatigue management, work diaries and emergency procedures

    Your employer's schedule would require you to drive beyond your permitted hours. What is the correct response?

    1. Drive to the schedule and note it in the diary later
    2. Refuse to break the hours and tell your employer Correct answer.
    3. Drive to the schedule because the employer is responsible
    4. Drive faster to finish the schedule on time

    Explanation

    Drivers must not exceed their permitted work hours, and employers and schedulers also have duties not to cause a breach. If a schedule cannot be met legally, the driver should say so rather than drive outside the rules.

  185. Question 185Fatigue management, work diaries and emergency procedures

    According to fatigue research, at which times is a driver most likely to feel sleepy?

    1. Early afternoon and early morning Correct answer.
    2. Mid-morning and mid-afternoon
    3. Late morning and early evening
    4. Just before and after midday

    Explanation

    The body's natural sleepiness peaks in the early hours of the morning and again in the early afternoon. Trips that run through these periods carry a higher risk of the driver falling asleep at the wheel.

  186. Question 186Fatigue management, work diaries and emergency procedures

    Your truck stalls and stops on a level crossing. What should you do?

    1. Try to push the truck off the crossing
    2. Get out and move clear, then phone 000 Correct answer.
    3. Stay in the cab and try to restart the engine
    4. Wave to warn any approaching train

    Explanation

    Occupants should leave the vehicle immediately and move well clear of the crossing before calling emergency services. A train cannot stop quickly enough to avoid a collision, so staying with the vehicle is extremely dangerous.

  187. Question 187Fatigue management, work diaries and emergency procedures

    Smoke starts coming from under the bonnet of your truck. What should you do?

    1. Keep driving to the nearest fire station
    2. Stop, get everyone out and call 000 Correct answer.
    3. Open the bonnet fully to look for the fire
    4. Pour water into the fuel tank

    Explanation

    Stop as soon as it is safe, switch off the engine, get everyone out and move well clear before calling 000. Fully opening the bonnet can feed oxygen to the fire and cause it to flare up violently.

  188. Question 188Fatigue management, work diaries and emergency procedures

    You are involved in a crash and another person is injured. What must you do?

    1. Wait for the other driver to call for help
    2. Stop, give what help you can and call 000 Correct answer.
    3. Drive on and report it at the next police station
    4. Move the injured person immediately then leave

    Explanation

    After a crash you must stop, give reasonable assistance to anyone injured and make sure emergency services are called. Details must also be exchanged with the other parties involved.

  189. Question 189Fatigue management, work diaries and emergency procedures

    Liquid is leaking from a drum on your truck and you do not know what the substance is. What is the safest action?

    1. Continue to the delivery point and report it there
    2. Lift the drum off the truck yourself
    3. Wash the spill off the tray with water
    4. Stop, stay upwind and call emergency services Correct answer.

    Explanation

    An unknown spill may be hazardous, so keep clear, stay upwind to avoid fumes, remove ignition sources and call 000. Only attempt to control a spill if you know what the substance is and it can be done safely.

  190. Question 190Fatigue management, work diaries and emergency procedures

    Your brakes fail as you descend a steep hill. What is the best response?

    1. Pump the brakes hard and steer for the shoulder
    2. Open the door and prepare to jump clear
    3. Change down gears and use engine braking Correct answer.
    4. Switch off the engine and coast downhill

    Explanation

    Selecting a lower gear uses engine braking to slow the vehicle without relying on the footbrake, and gentle handbrake use or a runaway ramp can then help bring it to a stop. Switching off the engine removes power steering and engine braking.

  191. Question 191Fatigue management, work diaries and emergency procedures

    Which statement about tiredness is correct?

    1. A big coffee will fully restore alertness
    2. Lost sleep builds up over time Correct answer.
    3. Fresh air from an open window cures it
    4. You can catch up on sleep while driving

    Explanation

    Sleep loss accumulates, so several short nights leave you more impaired than one long one, and the debt must be repaid with actual sleep. Caffeine, fresh air and loud music only mask the symptoms for a short time.

  192. Question 192Fatigue management, work diaries and emergency procedures

    You have taken your 15-minute rest break but still feel very sleepy. What should you do?

    1. Continue because 15 minutes is all the law requires
    2. Slow down slightly and keep going
    3. Take a longer rest until you are fit to drive Correct answer.
    4. Drink an energy drink and continue

    Explanation

    The legal minimum break is not a guarantee of alertness; if you are still sleepy you must rest longer or sleep before driving on. Driving while impaired by fatigue is an offence as well as a serious safety risk.

  193. Question 193Fatigue management, work diaries and emergency procedures

    A driver working standard hours has recorded 70 hours of work in the past 7 days. How much more work can the driver do in that 7-day period?

    1. 8 hours
    2. 14 hours
    3. 2 hours Correct answer.
    4. 4 hours

    Explanation

    Standard hours allow a maximum of 72 hours of work in any 7-day period, so with 70 hours already recorded only 2 more hours are permitted. The driver must still stay within the 12-hour daily limit and the required rest breaks.

  194. Question 194Fatigue management, work diaries and emergency procedures

    You are about to set off on a long overnight trip in your heavy rigid truck. Which approach best manages your fatigue?

    1. Plan the trip to include regular rest stops Correct answer.
    2. Skip breaks so you arrive ahead of schedule
    3. Drive through the night while traffic is light
    4. Drink several energy drinks before departing

    Explanation

    Fatigue is managed by planning: build regular rest breaks into the trip and stop for proper rest when you feel sleepy. Stimulants, deliberately driving through the night and skipping breaks all increase the risk of a fatigue-related crash rather than reducing it.

  195. Question 195Fatigue management, work diaries and emergency procedures

    Which of these is a recognised warning sign that you are becoming fatigued while driving?

    1. Feeling hungry and thinking about your next meal
    2. Feeling bored and wanting to change radio stations
    3. Yawning often and struggling to stay awake Correct answer.
    4. Feeling cold and turning the cabin heater up

    Explanation

    Yawning repeatedly, heavy eyelids and difficulty staying awake are direct signs that your alertness is dropping and you need to stop and rest. These signs should be acted on immediately, because fatigue can progress to a microsleep without warning.

  196. Question 196Fatigue management, work diaries and emergency procedures

    You realise you have written an incorrect work time in your work diary. What is the proper way to fix the record?

    1. Write the new figure over the top of the old one
    2. Tear the page out and start a fresh page
    3. Draw one line through it and write the correct entry Correct answer.
    4. Erase the entry so that the original mistake no longer shows

    Explanation

    Corrections must leave the original entry still readable, so a single line is drawn through the wrong entry and the correct particulars are written alongside it. Entries cannot be erased, obliterated or covered up, because the diary must show a true and complete record of your work.

  197. Question 197Fatigue management, work diaries and emergency procedures

    A driver of a heavy rigid truck works under standard hours, stays within 100 km of the base and never works more than 12 hours in a 24-hour period. What is the driver's work diary obligation?

    1. A diary is required only for night shifts
    2. No work diary is required for this driver Correct answer.
    3. A diary must be sent to the Regulator each month
    4. A work diary must be completed every day

    Explanation

    A driver working under standard hours who stays within 100 km of the base and does not exceed 12 hours of work in any 24-hour period is exempt from keeping a work diary. The exemption relies on all of those conditions being met, so losing any one of them brings the diary requirement back.

  198. Question 198Fatigue management, work diaries and emergency procedures

    A front tyre on your truck blows out at highway speed. What should you do?

    1. Accelerate to keep the vehicle tracking straight
    2. Grip the wheel, ease off and slow gradually Correct answer.
    3. Brake as hard as possible to stop quickly
    4. Swerve straight onto the shoulder at speed

    Explanation

    After a blowout the vehicle will pull towards the failed tyre, so you hold the wheel firmly and keep it straight, ease off the accelerator and let speed fall before moving off the road. Hard braking or sudden steering can throw the truck out of control.

  199. Question 199Fatigue management, work diaries and emergency procedures

    Your headlights fail suddenly while you are driving at night on an unlit road. What should you do?

    1. Stop safely off the road and use hazard lights Correct answer.
    2. Follow close behind another vehicle's tail lights
    3. Switch on high beam and continue the trip
    4. Keep driving at low speed on park lights only

    Explanation

    With no headlights you can neither see the road ahead nor be seen by other road users, so you must get the vehicle off the road as soon as it is safe, switch on hazard lights and not continue. Continuing without headlights, or tailgating another vehicle to use its lights, is dangerous and unlawful.

  200. Question 200Fatigue management, work diaries and emergency procedures

    You have worked for 5 hours without a rest break and your destination is 45 minutes away. Under standard hours, what must you do?

    1. Take a 15-minute rest break before going on Correct answer.
    2. Stop only if you start feeling sleepy
    3. Drive on but at a much lower speed
    4. Continue, because 45 minutes is a short drive

    Explanation

    Under standard hours you must not work for more than 5 hours 15 minutes without a rest break of at least 15 minutes. Driving the remaining 45 minutes would take you past that limit, so you must take the break before continuing.

VIC Heavy Rigid Knowledge Test flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Heavy Rigid (HR) licence
A Victorian licence class covering rigid vehicles with a GVM over 8 tonnes, or 3 or more axles, and towing a trailer up to 9 tonnes GVM.
Heavy Combination (HC) licence
Covers articulated vehicles and rigid vehicles towing a trailer over 9 tonnes GVM, such as a prime mover and semitrailer combination.
Multi-Combination (MC) licence
Covers multi-combinations of two or more trailers, including B-doubles, B-triples and road trains.
Zero blood alcohol limit
In Victoria a zero blood alcohol concentration limit applies to drivers of vehicles over 15 tonnes GVM, buses and driving instructors.
Gross Vehicle Mass (GVM)
The maximum loaded mass a vehicle is designed to carry, set by the manufacturer: tare mass plus the maximum payload.
General Mass Limits (GML)
Default legal mass limits: 6 tonnes on a steer axle, 9 tonnes on a single axle with dual tyres, 16.5 tonnes tandem and 20 tonnes tri-axle.
Tare mass
The unladen mass of a vehicle with fuel and fluids but no load or occupants; payload equals GVM minus tare mass.
Higher Mass Limits (HML)
Mass limits above the general limits, available only on approved routes to accredited vehicles with road-friendly suspension.
Pre-start check
An inspection before driving covering tyres, lights, fluids, brakes, steering, mirrors and load security, used to find defects before departure.
Air brake pressure test
With the engine off and brakes applied, air pressure loss must stay within the manufacturer's limit, and the low-pressure warning must operate.
Heavy vehicle tyre tread
Heavy vehicle tyres must have at least 1.5 millimetres of tread across the tread width and no cuts, bulges or exposed cords.
Coupling check
For articulated vehicles, confirm the kingpin is locked in the turntable, the safety clip is engaged and the trailer is secure before moving.
Major defect
A defect making a heavy vehicle unsafe or non-compliant, such as brake or steering failure; the vehicle must not be driven until repaired.
Minor defect
A defect that does not significantly affect safety but must be recorded and repaired within the time set by the operator or regulator.
Defect reporting
The driver must report any defect to the operator and record it; driving a defective heavy vehicle is an offence.
Defect notice
Issued by an authorised officer for a non-compliant vehicle; a major defect notice prohibits the vehicle from being used until cleared.
Load restraint standard
The restraint system must withstand 0.8 g deceleration forward and 0.5 g rearward and sideways, relative to the mass of the load.
Tie-down restraint
A method where lashings or straps clamp the load down onto the vehicle deck; the lashings must be rated for the required restraint force.
Direct restraint
A method where a headboard, barrier, gate or twistlock holds the load directly; components must be rated for the forces involved.
Curtainsider
A trailer with flexible side curtains; the curtains provide weather protection only and must not be relied on to restrain a load.
Four-second following gap
A safe following gap for a heavy vehicle is at least four seconds behind the vehicle ahead, longer in rain or poor visibility.
Engine braking
Using a lower gear so the engine slows the vehicle on a descent, reducing brake fade; select the gear before the descent begins.
Brake fade
Loss of braking power when brakes overheat from continuous use, common on long descents; avoided by gearing down and using retarders.
Off-tracking
The tendency of the rear wheels of a long vehicle to cut inside the path of the front wheels when turning.
Maximum vehicle width
The maximum legal width for a heavy vehicle in Australia is 2.5 metres unless an oversize permit applies.
Maximum vehicle height
The general maximum height for a heavy vehicle is 4.3 metres; low bridges and tunnels may impose lower limits on a route.
Keep left rule
On multi-lane roads with a speed limit over 80 km/h, a driver must keep left unless overtaking.
Passing cyclists
A driver must leave at least 1 metre when passing a cyclist at up to 60 km/h, and 1.5 metres above 60 km/h.
Standard fatigue hours
Solo drivers must not work more than 12 hours in 24 or 72 hours in 7 days, and need 7 continuous hours stationary rest in 24 hours.
Work diary
A record of work and rest required for drivers of heavy vehicles over 12 tonnes GVM travelling more than 100 km from their home base.
24-hour rest requirement
A solo driver must have at least 24 continuous hours of stationary rest in each 7-day period.
Breakdown procedure
Move the vehicle off the road, switch on hazard lights, place warning triangles and call 000 if anyone is injured.

VIC Heavy Rigid Knowledge Test study guide

Heavy Vehicle Licensing: Classes, Scope and Obligations

Where HR sits in the ladder

Victorian heavy vehicle classes are cumulative and are defined by axle count and gross vehicle mass. Light rigid (LR) covers a rigid vehicle from 4.5 to 8 tonnes GVM and may tow a trailer up to 9 tonnes GVM. Medium rigid (MR) covers a two-axle rigid vehicle with a GVM over 8 tonnes, again towing up to 9 tonnes. Heavy rigid (HR) covers a rigid vehicle with three or more axles and a GVM over 8 tonnes. Above HR sit heavy combination (HC) and multi-combination (MC), which you need for semi-trailers, B-doubles and trailers heavier than 9 tonnes GVM.

Because the classes stack, an HR licence also lets you drive LR and MR vehicles. It does not let you drive a prime mover, a B-double, or a truck towing a trailer heavier than 9 tonnes GVM. Knowledge questions exploit this constantly: a scenario describing a three-axle truck pulling a 12-tonne dog trailer is an HC job, not HR.

Getting and keeping the licence

The pathway is: hold a current non-probationary car licence, pass the heavy vehicle knowledge test, be issued a heavy vehicle learner permit, complete supervised driving or accredited training, then pass the driving assessment. Medical and eyesight standards apply, and conditions such as an automatic-transmission restriction carry across.

Heavy vehicle drivers are held to a higher standard. In Victoria, a zero blood alcohol concentration applies to drivers of vehicles over 15 tonnes GVM and to bus drivers, and heavy vehicle offences attract demerit points, suspension and disqualification.

Rule of thumb: if the trailer's GVM is 9 tonnes or less, HR can tow it; anything heavier moves you to HC.

Pre-start checks, vehicle inspection and defects

Vehicle Categories, Mass and Dimension Limits

The numbers that matter

Tare mass is the empty vehicle. GVM is the manufacturer's maximum loaded mass of the vehicle itself. GCM is the maximum loaded mass of the vehicle plus any trailer it tows. Payload is simply GVM minus tare. Registration and the compliance plate restate these limits but never raise them.

Axle and axle-group limits

Under general mass limits, common maximums are: a single steer axle 6.0 tonnes; a single axle on dual tyres 9.0 tonnes; a tandem axle group 16.5 tonnes; a tri-axle group 20.0 tonnes. Tyre size and ply rating, suspension type and axle spacing all reduce these figures, so a tri-axle group on small tyres cannot legally carry 20 tonnes.

The overall mass limit is the lowest of GVM, the sum of the axle-group limits and any registered or permit limit. Concessional and higher mass limits exist but only with accreditation and, usually, road-friendly suspension.

Dimensions

Standard limits are 2.5 m wide, 4.3 m high and 12.5 m long for a rigid vehicle. Anything wider, higher or longer needs a permit or pilot and escort arrangements.

Traps

Questions love to give you a load that is under GVM but badly placed, so an axle group is overloaded. Mass must be distributed, not just totalled. Another trap is confusing GCM with GVM when a trailer is attached.

Worked example: a three-axle tipper has a GVM of 24 t and tare of 11 t, giving a payload of 13 t. You load 12 t, so you are under GVM - but if 9 t of that sits over the rear tri-axle group and the group limit is 20 t with the body's own weight included, you may still be legal here while overloading the steer axle if the load sits too far forward. Always check the distribution.

Pre-Start Checks

A legal duty, not a ritual

The pre-start check is the driver's first defence against breakdown and crash, and failing to do one can leave you exposed if a defect causes an incident. Do it the same way every time, in the same order, so nothing gets skipped when you are rushed.

The walk-around

Start at the driver's door and work around the vehicle. Check for fresh fluid leaks underneath; tyres for pressure, cuts, bulges, exposed cord, tread depth, objects wedged between dual tyres and correct dual spacing; wheel nuts and alignment indicators; lights and reflectors, ideally using a reflective surface or a second person; mirrors, glass, wipers and the horn; suspension, springs, airbags, U-bolts and shock absorbers; mudflaps, number plates and the load.

For a combination, check the coupling last but thoroughly: fifth wheel jaws closed around the kingpin, the dog clip or safety latch in place, turntable secure, air lines and electrical lead connected and not rubbing, trailer parking brake operational and the landing legs wound up.

Air brake test

With the engine running, build pressure to governor cut-out. Switch off with the service brake applied and watch the gauge over one minute - the drop must stay within the manufacturer's leak limit. Confirm the low-pressure warning operates and the park brake holds.

In the cabin

Seat and belt adjusted, all warning lights extinguish after start-up, gauges reading normally, fire extinguisher, warning triangles and first aid kit present, and mirrors set for the load you are carrying.

Rule of thumb: if you would not be confident signing your name to it, do not drive it. A defect found in the yard costs minutes; one found at highway speed costs lives.

Inspection, Defects and Reporting

Minor versus major

A minor defect is one that does not make the vehicle unsafe to drive but must be fixed soon - a blown marker lamp, a worn wiper blade, a cracked mirror. A major defect affects safety or emissions and grounds the vehicle until it is repaired: faulty brakes, a broken spring, a cracked wheel, steering play, a leaking air line, an insecure load.

What you must do

If you find a defect, you must not drive a vehicle that is unsafe. Report it to the operator, and where your system requires it, record it in writing. Under the national heavy vehicle rules the operator must keep records and act on defects, and the driver must not drive a vehicle that has been grounded or that they know is defective.

Authorised officers can issue defect notices. An official caution records a minor issue; a minor defect notice requires repair and, usually, self-clearance within a set period; a major defect notice grounds the vehicle and requires inspection before it may be used again. Ignoring a notice and driving anyway is a serious offence.

Routine inspection

Between formal services you are the inspector. Watch for brake drag, air pressure loss overnight, uneven tyre wear (which signals alignment or load problems), oil and coolant loss, and anything that feels different through the wheel or the seat. A driver who reports early prevents a roadside grounding later.

Worked example: during a pre-start you find one rear inner dual tyre flat. That is not a minor defect - running on the outer tyre overloads it and can cause a blowout. The vehicle stays parked, the operator is notified, and the wheel is changed before the trip begins, even if it makes the delivery late.

Load Restraint and Load Security

The performance standard

A load restraint system must be able to withstand the forces of heavy braking, acceleration and cornering without the load shifting. The accepted figures are: 0.8 g forward, 0.5 g rearward and 0.5 g sideways, measured against the weight of the load. For a 10-tonne load that means restraining 8 tonnes forward and 5 tonnes in each other direction.

Methods

Containment uses the vehicle body - headboards, gates, stakes, dropsides - to block movement. Blocking places timber or purpose-made structures against the load. Direct lashing attaches the load to the vehicle. Tie-down lashing presses the load onto the deck so friction holds it, and relies on having enough tension and enough friction between load and deck.

Curtains do not restrain a load; they are weather protection only.

Capacity and angles

Each component has a lashing capacity (LC) and a pre-tension. Aggregate capacity must exceed the force required. Angles matter: a lashing running at 45 degrees to the direction of the force contributes only about 70 per cent of its capacity, so you need more lashings, not longer ones.

Traps

Questions test whether you count the load's weight rather than its rated capacity, whether you assume curtains are restraint, and whether you allow for friction only when it can be justified.

Worked example: a 12-tonne excavator on a drop deck needs 0.8 x 12 = 9.6 tonnes of forward restraint. Chains rated at 5 tonnes LC each, running at 45 degrees, contribute about 3.5 tonnes each, so two chains are not enough - three gives you about 10.5 tonnes and is the minimum acceptable arrangement, plus a check that the bucket is secured.

Fatigue management, work diaries and emergency procedures

Driving Techniques: Braking, Gearing, Cornering and Following Distance

Braking

Heavy vehicles run air brakes, which have a noticeable lag between pedal and response, and stopping distance grows sharply with mass. Brake early, brake smoothly, and leave room. On a long descent, continuous light braking overheats the drums and causes brake fade - the pedal goes soft and nothing much happens. Prevent it by selecting a low gear before the crest, using the engine brake or retarder, and applying snub braking: firm applications that pull speed down 10 to 15 km/h, then release, letting the engine hold the speed between applications.

Gearing

Change down before the hill, not on it. Keep the engine in its torque band and use progressive, unhurried changes. Coasting in neutral or with the clutch in is illegal in effect and dangerous in practice - you lose engine braking and control.

Cornering

A loaded truck carries its weight high, and its rollover threshold is low. Centrifugal force rises with the square of speed: double your speed through a corner and you quadruple the force trying to tip you over. Brake before the corner, hold a steady speed through it, and accelerate gently out. Watch for loads that shift and for soft shoulders and cambers.

Following distance

Use at least a four-second gap in good conditions, and more in rain, darkness, poor visibility or when heavily loaded. The gap buys you reaction time and lets cars pull into the space ahead rather than cutting you off.

Rule of thumb: if the vehicle ahead passes a pole and you reach it before you can say four full seconds, you are too close.

Fatigue Management, Work Diaries and Emergency Procedures

Fatigue is regulated, not optional

Fatigue rules under the national heavy vehicle law set maximum work and minimum rest. Under standard hours you may work no more than 12 hours in any 24-hour period, must take a continuous break of at least 5.5 hours of stationary rest in that 24 hours, and must not work more than 72 hours in any 7 days. Longer cycles impose additional requirements, including night rest breaks.

Your work diary records work and rest in 15-minute blocks. It must be carried while driving, completed honestly, and kept for the required retention period. False entries are a serious offence, and so is driving while over your allowed hours - the officer checks the diary, not your intentions.

Warning signs to act on: yawning, heavy eyes, drifting within the lane, missing signs, and not remembering the last few kilometres. Pull over somewhere safe and rest; coffee and open windows are not a substitute for sleep.

Emergencies

If you break down, get as far off the carriageway as you can, switch on hazard lights, and set out warning triangles well behind the vehicle - much further back on a highway than in town. Keep passengers away from the traffic side. For fire, stop, evacuate upwind and call 000. For a crash, secure the scene, give first aid within your training, and report the incident to police and your operator. Never attempt a roadside repair in a live lane.

Rule of thumb: if you feel tired enough to ask yourself whether you are tired, you already are - stop at the next safe place rather than the next town.

Road Rules, Signage and Sharing the Road Safely

Speed and lane rules

Heavy vehicles are limited to 100 km/h and may be governed lower. On multi-lane roads with a speed limit over 80 km/h, heavy vehicles must keep out of the right-hand lane unless overtaking or turning. Keep left otherwise, and never straddle two lanes to block traffic behind you.

Signs that apply specifically to you

Learn the signs that restrict heavy vehicles: no trucks, no heavy vehicles over a stated mass, load limits on bridges, clearance height signs, and route restrictions. A clearance sign gives a height that is the lowest point, not an average - if the sign says 4.2 m and your combination is 4.3 m, you stop and find another route.

Sharing the road

Trucks have large blind spots directly in front, along both sides and behind. Cyclists, motorcyclists and pedestrians can disappear into them at intersections - check twice, and watch for riders filtering on your left. At roundabouts, stay in your lane and watch for vehicles in your blind spot; long vehicles may need to use more than one lane, so signal clearly and early.

Special situations

Approach railway crossings expecting to stop, never change gears on the crossing, and make sure there is room on the far side before you commit. Slow down in roadworks and follow traffic controllers' directions. Give cyclists at least a metre, more at higher speeds. When merging, be predictable rather than polite to the point of hesitation.

Rule of thumb: if you cannot see the driver's face in their mirror, they cannot see you - apply exactly the same logic to where you position your own truck.

VIC Heavy Rigid Knowledge Test cheat sheet

Quick reference

Heavy vehicle licensing

  • An HR (Heavy Rigid) licence covers a rigid vehicle with a GVM over 8 tonnes, or a rigid vehicle with 3 or more axles, and towing a trailer with a GVM up to 9 tonnes.

  • An HC (Heavy Combination) licence covers articulated combinations and rigid vehicles towing a trailer over 9 tonnes GVM; an MC (Multi-Combination) licence covers B-doubles, B-triples and road trains.

  • An HR licence also authorises driving every vehicle covered by lower licence classes (car and light rigid).

  • Heavy vehicle licence applicants in Victoria must be at least 18 years old and hold a current full (non-probationary) car licence.

  • Obtaining an HR licence requires passing a knowledge test and an eyesight test, meeting medical fitness standards and passing a practical driving assessment or approved competency course.

  • In Victoria a zero blood alcohol concentration limit applies to drivers of vehicles over 15 tonnes GVM, buses and driving instructors.

  • Demerit points accumulate across all licence classes; 12 points within 3 years suspends an unrestricted driver.

  • A driver must carry their licence while driving and produce it to police on request; heavy vehicle licences also require a current medical clearance.

Quick reference

Vehicle categories and mass limits

  • GVM is the maximum loaded mass of the vehicle itself; GCM is the maximum loaded mass of the vehicle plus any trailer it tows.

  • Payload = GVM minus tare mass (the unladen mass of the vehicle with fuel and fluids but no load).

  • General Mass Limits (GML): steer axle 6.0 t, single axle with dual tyres 9.0 t, tandem axle group 16.5 t, tri-axle group 20.0 t, or the tyre/manufacturer rating if lower.

  • A 3-axle rigid with a tandem rear group under GML can operate at 6.0 t + 16.5 t = 22.5 t.

  • Concessional Mass Limits (CML) allow 5% above GML for vehicles accredited under the National Heavy Vehicle Accreditation Scheme.

  • Higher Mass Limits (HML) apply only on approved routes to accredited vehicles fitted with road-friendly suspension such as air suspension.

  • An axle load must not exceed the lowest of the statutory limit, the tyre load rating and the axle or suspension manufacturer's rating.

  • Exceeding a gross, axle group or axle mass limit is an offence and penalties increase with the amount overweight.

Quick reference

Pre-start checks

  • Check every tyre, including the spare, for tread depth of at least 1.5 mm, cuts, bulges, exposed cords and correct pressure.

  • Check engine oil, coolant, brake fluid, power steering fluid and washer fluid, and look for leaks under the vehicle.

  • Test all lights: headlights, indicators, brake lights, marker and clearance lights, reverse lights and any beacons.

  • Build air pressure until the governor cuts out, confirm the low-pressure warning operates, then check for air leaks with the engine off.

  • Check mirrors, windscreen, wipers, washers, horn and seat belts for condition and operation.

  • Check steering for excessive free play, and inspect suspension, springs or airbags and wheel nut indicators.

  • Confirm the load is within mass limits and secured, and on combinations check the kingpin, turntable and safety clip.

  • Confirm the fire extinguisher, warning triangles and first aid kit are present and in date.

Quick reference

Vehicle inspection and defects

  • A major defect makes the vehicle unsafe or non-compliant (for example brake failure, steering failure or a tyre with exposed cords) and the vehicle must not be driven.

  • A minor defect does not significantly affect safety but must be recorded and repaired within the time set by the operator or regulator.

  • The driver must report defects to the operator and record them; the operator must keep maintenance and repair records.

  • Driving a heavy vehicle with a known major defect is an offence and may void insurance cover.

  • Pre-trip and post-trip inspections form part of the chain of responsibility obligations for heavy vehicle safety.

  • Authorised officers may issue defect notices; a major defect notice prohibits use of the vehicle until it is cleared.

  • Clearing a defect notice requires the defect to be repaired and, where specified, the repair to be inspected by an authorised officer.

  • On an air-braked vehicle the low-pressure warning must activate before pressure drops below the safe operating level.

Quick reference

Load restraint and load security

  • The load restraint system must withstand 0.8 g deceleration forward and 0.5 g rearward and 0.5 g sideways, relative to the mass of the load.

  • Tie-down lashings clamp the load onto the deck; the aggregate lashing capacity must exceed the calculated restraint force for the load.

  • Direct restraint (headboard, barriers, gates, twistlocks) must be rated for the load and must not rely on friction alone.

  • Curtainsiders do not restrain loads; the curtains provide weather protection and containment only.

  • A loaded vehicle must remain within its GVM, GCM and axle group limits after loading.

  • A load projecting more than 1.2 m beyond the rear of the vehicle requires a warning flag by day and a warning light at night.

  • Distribute the load evenly, keep the centre of gravity low and re-check axle loads after loading.

  • Inspect straps and chains for cuts, fraying, corrosion and damaged fittings before use, and fit edge protectors where straps contact sharp edges.

Quick reference

Driving techniques for heavy vehicles

  • A safe following gap for a heavy vehicle is at least 4 seconds behind the vehicle ahead, increased in rain, at night or when fully loaded.

  • Total stopping distance = reaction distance + braking distance; braking distance increases with the square of speed.

  • Air brakes have a lag, so apply the brakes earlier than in a car and avoid riding the brake pedal.

  • Select a lower gear before starting a descent; never coast downhill in neutral.

  • Use engine braking or a retarder where permitted, and obey signs that ban engine brakes.

  • Slow down before entering a corner; a high centre of gravity increases rollover risk.

  • Long vehicles off-track, meaning the rear wheels cut inside the path of the front wheels in tight turns, so allow extra room.

  • Use mirrors and check blind spots before changing lanes, signal early and allow extra time for the manoeuvre.

Quick reference

Road rules, signage and sharing the road safely

  • On multi-lane roads where the speed limit is over 80 km/h, a driver must keep left unless overtaking.

  • Where a sign requires it, heavy vehicles must not use the right-hand lane.

  • General dimension limits: width 2.5 m, height 4.3 m, rigid vehicle length 12.5 m and combination length 19 m.

  • Default speed limits: 50 km/h in built-up areas, 100 km/h on rural roads unless signed otherwise, and 40 km/h in school zones when children are present.

  • When passing a cyclist, leave at least 1 m at speeds up to 60 km/h and at least 1.5 m above 60 km/h.

  • At a yellow traffic light, stop if it is safe to do so; otherwise proceed with caution.

  • Give way to all traffic already in a roundabout, and indicate left before exiting.

  • A heavy vehicle must not be driven on a footpath or nature strip unless a sign or permit allows it.

Quick reference

Fatigue management, work diaries and emergency procedures

  • Standard solo hours: no more than 12 hours work in any 24 hours, no more than 72 hours work in 7 days, at least 7 continuous hours stationary rest in 24 hours and at least 24 continuous hours rest in 7 days.

  • A work diary is required for drivers of heavy vehicles over 12 tonnes GVM travelling more than 100 km from their home base.

  • Diary entries must record all work and rest, not just driving, and must be completed at the start and end of each work period.

  • The work diary must be carried while driving, produced on request and the records retained for 3 years.

  • Warning signs of fatigue include yawning, drifting between lanes, poor concentration and heavy eyes.

  • For a breakdown, move off the road where possible, switch on hazard lights and place warning triangles before calling for help.

  • For a fire, stop the vehicle, evacuate upwind and call 000; do not fully open the engine cover if an engine fire is suspected.

  • If a vehicle stops on a rail crossing, get everyone out and clear, then call 000 and the rail operator.

VIC Heavy Rigid Knowledge Test key terms

HR (Heavy Rigid) licence

A Victorian driver licence class that allows you to drive a rigid motor vehicle with a gross vehicle mass over 8 tonnes, and to tow a trailer with a gross vehicle mass up to 9 tonnes.

Related: Gross Vehicle Mass (GVM), Heavy Vehicle National Law (HVNL)
Gross Vehicle Mass (GVM)

The maximum loaded mass a vehicle is designed to carry, as set by the manufacturer. It includes the vehicle's own mass plus fuel, occupants and cargo, and must never be exceeded.

Related: Gross Combination Mass (GCM), Tare mass, Overloading
Gross Combination Mass (GCM)

The maximum loaded mass of a motor vehicle and any trailers it tows combined, as specified by the manufacturer. It applies to the whole combination, not just the towing vehicle.

Related: Gross Vehicle Mass (GVM), Prime mover, Aggregate Trailer Mass (ATM)
Tare mass

The mass of a vehicle with no cargo or passengers, as specified by the manufacturer, including coolant, lubricants, tools and a small amount of fuel. It is used to work out how much load can be carried.

Related: Gross Vehicle Mass (GVM), Load distribution
Aggregate Trailer Mass (ATM)

The maximum loaded mass of a trailer as set by its manufacturer, including the load it carries and the mass it places on the towing vehicle's coupling.

Related: Gross Combination Mass (GCM), Lashing
Axle mass limit

The maximum mass permitted on a single axle or group of axles, set by the vehicle manufacturer or by heavy vehicle mass rules. Exceeding it overloads tyres, brakes and the road surface.

Related: Gross Vehicle Mass (GVM), Load distribution, Overloading
Rigid truck

A heavy vehicle built as one unit, with the cabin and load-carrying body on the same chassis and no articulation point. It may tow a trailer but does not bend in the middle.

Related: Prime mover, HR (Heavy Rigid) licence
Prime mover

A heavy vehicle designed mainly to tow a semi-trailer. It has a turntable, or fifth wheel, over the rear axles that the trailer couples to, so part of the trailer's mass is carried by the prime mover.

Related: Gross Combination Mass (GCM), Rigid truck, Auxiliary brake (retarder)
Heavy Vehicle National Law (HVNL)

The national legislation, applied in Victoria, that sets rules for heavy vehicle mass, dimensions, loading, fatigue and maintenance, and places duties on everyone who influences how a heavy vehicle is used.

Related: National Heavy Vehicle Regulator (NHVR), Chain of responsibility, Standard hours
National Heavy Vehicle Regulator (NHVR)

The independent body that administers the Heavy Vehicle National Law. It issues permits and defect notices and provides guidance on heavy vehicle operations, including load restraint and fatigue management.

Related: Heavy Vehicle National Law (HVNL), Oversize or overmass permit, Defect notice
Chain of responsibility

The principle in heavy vehicle law that everyone who influences a heavy vehicle's use, including operators, schedulers, loaders, consignors and drivers, shares legal responsibility for compliance with mass, loading, speed and fatigue rules.

Related: Heavy Vehicle National Law (HVNL), Overloading, Load restraint
Overloading

Operating a vehicle or axle above its permitted mass limit. Overloading reduces braking and steering performance, damages roads and is an offence for the driver and for other parties in the supply chain.

Related: Axle mass limit, Load distribution
Oversize or overmass permit

A written approval issued by the National Heavy Vehicle Regulator allowing a vehicle or combination that exceeds standard mass or dimension limits to travel on specified roads, usually with conditions such as approved routes and escort requirements.

Related: National Heavy Vehicle Regulator (NHVR), Overloading
Pre-start check

A systematic inspection carried out before driving, covering tyres, wheels, lights, brakes, fluids, load and coupling security, so faults are found and fixed before the vehicle is used on the road.

Related: Defect, Major defect, Load restraint
Defect

A fault or condition on a vehicle, trailer or its equipment that affects, or could affect, safety, or that means it does not comply with the standards required for use on the road.

Related: Major defect, Minor defect, Defect notice
Major defect

A defect that makes a heavy vehicle unsafe or a serious risk to safety, such as a badly worn tyre or a failed brake. The vehicle must not be driven until the defect is repaired.

Related: Defect notice, Unroadworthy vehicle
Minor defect

A defect that does not stop the vehicle being used immediately but must still be repaired within the time required by the notice, such as a faulty light or a small fluid leak.

Related: Defect notice, Major defect
Defect notice

An official notice issued after a roadside inspection or authorised officer's check that lists the defects found and states whether the vehicle can keep being used and by when repairs must be completed.

Related: Major defect, Minor defect, Unroadworthy vehicle
Unroadworthy vehicle

A vehicle that does not meet the safety and construction standards required to be driven on a road. Driving one is an offence and can void insurance and lead to licence action.

Related: Major defect, Defect notice
Load restraint

The system of lashings, gates, headboards and other equipment used to stop a load moving or falling from a vehicle. It must prevent movement in all directions under normal driving and emergency braking.

Related: Load Restraint Guide, Lashing, Load distribution
Load Restraint Guide

The national reference, published by the National Transport Commission, that sets out performance standards and methods for restraining loads on heavy vehicles, and which regulators and courts use as the benchmark.

Related: Load restraint, Lashing
Lashing

A strap, chain or rope used to tie a load to the vehicle. Lashings must be rated, in good condition and tensioned so the load cannot shift, tip or fall during braking, cornering or bumps.

Related: Load restraint, Headboard
Load distribution

How the weight of a load is spread over the vehicle's axles and along its length. Good distribution keeps every axle within its limit and keeps the centre of gravity low and central.

Related: Axle mass limit, Centre of gravity, Load restraint
Headboard

A strong barrier fitted at the front of a tray or trailer, directly behind the cabin, that stops the load from sliding forward when the vehicle brakes.

Related: Load restraint, Lashing
Centre of gravity

The point where a vehicle's and its load's weight is balanced. A high or off-centre centre of gravity makes a heavy vehicle more likely to roll over, especially in turns or on uneven ground.

Related: Load distribution, Off-tracking
Auxiliary brake (retarder)

A secondary braking system, such as an engine compression brake or a transmission retarder, that helps slow the vehicle on long descents without overheating the service brakes. Also called a Jake brake.

Related: Engine braking, Stopping distance
Engine braking

Using a low gear so the engine holds the vehicle back on a downhill grade. Select the gear before the descent begins so the service brakes are not relied on and do not overheat.

Related: Auxiliary brake (retarder), Stopping distance
Following distance

The gap between your vehicle and the one ahead, best measured in seconds. Heavy vehicles need a longer gap than cars because they take much further to stop when loaded.

Related: Stopping distance, Fatigue
Stopping distance

The total distance travelled from when a hazard appears until the vehicle stops: reaction distance plus braking distance. It grows quickly with speed, load and wet or loose surfaces.

Related: Following distance, Fatigue
Off-tracking

The tendency of a heavy vehicle's rear wheels to follow a path inside the front wheels when turning. Drivers must allow for it so the rear of the vehicle does not hit kerbs, poles or other vehicles.

Related: Blind spot, Load distribution
Blind spot

An area around a heavy vehicle that the driver cannot see in the mirrors, including directly in front, beside the cabin and close behind. Other road users should never assume they have been seen.

Related: Off-tracking, Vulnerable road users
Vulnerable road users

People at greater risk in traffic, such as pedestrians, cyclists, motorcyclists and horse riders. Heavy vehicle drivers should give them extra space and time, especially when turning or passing.

Related: Blind spot, Long vehicle sign
Long vehicle sign

A reflective sign marked 'LONG VEHICLE' that certain long combinations must display at the rear, and sometimes the front, so other drivers can judge the vehicle's length and overtake safely.

Related: Following distance, Vulnerable road users
Railway level crossing

A place where a road crosses a railway line. Heavy vehicle drivers must approach at a speed that lets them stop, check for trains in both directions and never enter unless there is room to clear the crossing.

Related: Stopping distance, Long vehicle sign
Work diary

A record book or electronic record in which a heavy vehicle driver writes their work, rest and other duty time. It must be accurate, kept current and produced when an authorised officer asks for it.

Related: Standard hours, Fatigue, Rest break
Standard hours

The default fatigue limits under the Heavy Vehicle National Law, setting maximum work hours and minimum rest periods over 24-hour, 7-day and 14-day periods, including breaks during a shift.

Related: Work diary, Rest break, Basic Fatigue Management (BFM)
Fatigue

Physical and mental tiredness that slows reaction time, reduces concentration and impairs judgement. It is a major cause of heavy vehicle crashes and must be managed through proper rest and planning.

Related: Rest break, Work diary, Standard hours
Rest break

A period of rest taken during a shift to manage fatigue. Under standard hours, drivers must not work more than a set number of hours without taking the required break.

Related: Fatigue, Standard hours
Basic Fatigue Management (BFM)

An accreditation under the Heavy Vehicle National Law that lets an operator with approved fatigue policies, scheduling and training work more flexible hours than standard hours, within set limits.

Related: Standard hours, Work diary
Warning triangle

A reflective, folding triangle carried in heavy vehicles and placed on the road around a broken-down vehicle to warn approaching traffic. Position it so drivers have time to slow down and pass safely.

Related: Long vehicle sign, Blind spot

VIC Heavy Rigid Knowledge Test study plan

8 weeks ยท About 6 hours per week

Week 1

Heavy vehicle licensing, vehicle categories and mass limits

  • List each heavy vehicle licence category and the vehicle or combination type it covers, from memory, without notes.

  • Define tare mass, GVM, GCM, payload and axle-group load, and state how each is derived from the others.

  • Calculate the available payload for three different vehicle configurations given tare mass and GVM.

  • Decide which limit governs when GVM, axle-group limits and posted road or bridge limits give different answers, and justify the choice.

Your checkpoint

A one-page reference sheet of licence categories and mass terms plus worked payload calculations for three configurations, self-marked with zero definition errors.

Week 2

Pre-start checks, vehicle inspection and defects

  • Write a 15-item pre-start inspection checklist covering tyres, brakes, lights, fluids, couplings, load anchorage points, mirrors and warning devices.

  • Run the checklist as a timed 10-minute walk-around on a parked heavy vehicle three times, recording anything missed.

  • Sort 20 described defects into 'do not drive', 'rectify before next trip' and 'monitor', stating the reporting action for each.

  • Explain, in writing, the procedure for a defect discovered mid-trip away from the depot.

Your checkpoint

Completed pre-start checklist plus a defect log of 20 classified entries, each with the correct action and who it is reported to.

Week 3

Load restraint and load security

  • Describe the forces acting on a load during braking, cornering and acceleration, and name the restraint that counters each.

  • Choose and justify a restraint method (tie-down, direct restraint or containment) for six written load scenarios.

  • Calculate the number and rating of tiedowns required for a given load using the restraint method taught in your learner guide.

  • Identify eight common load restraint failures from written descriptions and state the correction for each.

Your checkpoint

Load restraint worksheet covering six scenarios with chosen method, calculations and a one-sentence justification for each.

Week 4

Driving techniques for heavy vehicles (braking, gearing, cornering, following distances)

  • Describe correct braking technique and the factors that lengthen stopping distance for a laden versus an unladen rigid truck.

  • Explain gear selection and engine braking on a descent, including when a retarder or lower gear must be used instead of continuous service braking.

  • Describe safe cornering for a heavy vehicle, covering entry speed, load shift and off-tracking or swept path.

  • Calculate the following distance a heavy vehicle should hold at 60, 80 and 100 km/h using a 3-second gap.

Your checkpoint

Timed 40-question practice test spanning domains 1 to 4, scored at 85% or better, with every wrong answer written into an error log.

Week 5

Road rules, signage and sharing the road safely

  • Match 25 road signs and road markings to their meaning and the required driver action, without notes.

  • Describe how to negotiate a roundabout, a lane merge and a right turn in a long vehicle, including who must be given room.

  • List the checks made before travelling under a low clearance or along a route with mass or height restrictions.

  • Write out the give-way and sharing-the-road obligations owed to cyclists, pedestrians, motorcyclists and tram or bus lanes in your jurisdiction.

Your checkpoint

A 25-item sign and marking flash-card set scored cold at 100%, plus a written route-planning checklist for height, mass and clearance limits.

Week 6

Fatigue management, work diaries and emergency procedures

  • State the fatigue-management rules that apply to your operation, including work and rest hour limits and minimum break requirements.

  • List every item of information that must appear in a work diary entry and in a daily summary.

  • Identify five warning signs of fatigue in yourself and state the corrective action for each.

  • Write the step-by-step response to three emergency scenarios: brake failure, a tyre blowout at highway speed, and a load shift in traffic.

Your checkpoint

A completed sample work diary for seven days that passes a self-audit against the record-keeping requirements, plus written emergency response steps for the three scenarios.

Week 7

Heavy vehicle licensing, vehicle categories and mass limits & Pre-start checks, vehicle inspection and defects & Load restraint and load security

  • Re-attempt every question in the error log from weeks 1 to 6 and rewrite the reason each was missed.

  • Re-do the mass and payload calculations under time pressure until three consecutive correct answers are reached for each configuration.

  • Re-run the pre-start walk-around and defect classification without the checklist in front of you.

  • Redo the load restraint worksheet for the two scenarios that caused the most difficulty, this time without notes.

Your checkpoint

A cleared error log with every entry re-answered correctly and a dated note of the rule or concept that was misunderstood.

Week 8

Driving techniques for heavy vehicles (braking, gearing, cornering, following distances) & Road rules, signage and sharing the road safely & Fatigue management, work diaries and emergency procedures

  • Sit two full-length timed practice tests under exam conditions and record the score for each domain.

  • Review every incorrect answer from both tests and map it back to the domain and the specific rule involved.

  • Re-drill the two weakest domains until practice scores in them reach 90% or better.

  • Recite the licence categories, mass definitions and fatigue record-keeping requirements from memory as a final check.

Your checkpoint

Two completed full-length practice tests with scores logged per domain and a final one-page weak-spot sheet containing only the rules still being missed.

Milestones

Week 2: Complete the pre-start walk-around from memory with no more than two missed items and classify all 20 defects correctly.

Week 4: Score 85% or better on the 40-question domains 1 to 4 practice test.

Week 6: Pass a self-audit of the seven-day sample work diary with no missing required entries and correctly outline all three emergency responses.

Week 8: Score 90% or better on two consecutive full-length practice tests, with no domain below 85%.

VIC Heavy Rigid Knowledge Test exam day

Your checklist

Current Victorian driver licence (photo card)

Bring the physical card, not a copy or a photo on your phone. Your name and date of birth must match your booking exactly. If your licence is expired, lost or damaged, sort out a replacement before test day - confirm with the provider whether a temporary or digital licence is accepted.

Booking confirmation or appointment reference

Have your booking number, appointment time and location saved or printed. Confirm with the provider how your confirmation is issued and whether a printed copy is required.

Extra identification / evidence of address

Some transactions require a second form of ID or proof of Victorian residency. Confirm with the provider which documents are accepted so you are not turned away at the counter.

Glasses or contact lenses if you need them to drive

You may be asked to do a basic eyesight check as part of the process. If you normally wear correction, bring it and wear it, and make sure your licence condition reflects it.

Payment for the test fee

Fees and accepted payment methods change, so confirm the current amount and whether card, cash or online payment applies before you attend.

Completed application form (if required)

Some licence applications must be lodged on a form at the counter or in advance. Confirm with the provider whether this applies to your booking.

Details of your licence history

Know the dates you have held your current and previous licences, plus details of any suspensions or cancellations - you may be asked to declare them. Eligibility periods for heavy vehicle classes depend on how long you have held a licence, so confirm the requirement with the provider.

Medical or eyesight reports, if you have been asked for them

If you declared a medical condition or were requested to provide a medical/eyesight report, bring the original. Without it your test may not proceed.

Leave study notes, phones and smart devices out of the test room

Leave notes in the car or at home. Phones and smart watches must be switched off and stored as directed by staff - do not rely on being able to keep them on the desk.

Plan to arrive with time to spare

Allow extra time for parking, queueing and counter processing. Confirm with the provider how early they expect you to arrive and what happens if you are late.

Reading and accessibility needs arranged in advance

If you need an interpreter, extra time, a reader, or other adjustments, request them when booking - they usually cannot be arranged on the spot.

A plan for the rest of the day

Do not assume you will be driving a heavy vehicle yourself straight after the knowledge test. Confirm with the provider what the next steps are (training and practical assessment) and how you will get home.

Plan the day

72 hours before

Reconfirm your booking time, location and what you must bring by contacting the provider or checking your confirmation. Check your licence is current and undamaged, and locate your glasses or contacts.

72 hours before

Do focused revision on the areas you are weakest in - heavy vehicle mass and dimension limits, load restraint, stopping distances, fatigue rules and sharing the road with vulnerable users. Practise recalling rules rather than re-reading passively.

48 hours before

Do one or two full practice runs under timed conditions with no notes, then review only the questions you got wrong. Stop adding new material after this point.

24 hours before

Confirm your travel route, parking and expected journey time, allowing a buffer for traffic. Charge your phone, but plan to store it during the test.

24 hours before

Prepare your documents in one folder or bag - licence, confirmation, any medical reports, payment. Get a normal night's sleep rather than cramming late.

Morning of the test

Eat and hydrate normally. Re-read your own summary notes for 20โ€“30 minutes only; avoid last-minute debates about individual questions with other people.

Morning of the test

Arrive at the venue with the buffer you planned, check in at the counter, and follow staff directions on where to wait and what to store.

During the test

Read each question fully, including words like 'must', 'never' and 'except'. Answer the easy ones first and flag anything you are unsure of, then return to flagged items.

During the test

Answer from the road rules and safe heavy vehicle practice, not from what you have seen other drivers do. If a question genuinely confuses you, ask staff whether clarification is permitted - they cannot give you the answer.

After the test

Ask at the counter for your result and written confirmation of the next step (training, practical assessment or licence issue). Confirm fees and timeframes with the provider rather than assuming.

Rules to check

  • Bring original identification. Photocopies, expired documents and photos of documents are not acceptable, and your name must match the booking exactly.

  • Arrive at or before your appointment time. If you are late the provider may need to reschedule you and a fee may apply - confirm the late-arrival policy with the provider.

  • The knowledge test is closed-book and completed individually. Notes, textbooks, phones, smart watches and earpieces must be switched off and stored as directed.

  • Do not communicate with other candidates or attempt to share answers during the test. Suspected cheating can result in your test being voided and your application being refused.

  • Follow all directions from staff, including where to sit and when to start. If you do not understand an instruction, ask before you begin.

  • Tell staff in advance if you need a break, an interpreter, extra time or any other adjustment. Adjustments are usually arranged at booking, not on the day.

  • Your result and the pass mark are set by the provider. Ask the counter staff to confirm the outcome and any re-sit rules rather than relying on second-hand information.

  • Do not reproduce or discuss the content of specific test questions afterwards. Treat the questions as confidential and rely on official study material to prepare.

VIC Heavy Rigid Knowledge Test FAQ

How many VIC Heavy Rigid Knowledge Test practice questions are available?

The practice set has 200 VIC Heavy Rigid Knowledge Test questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many VIC Heavy Rigid Knowledge Test flashcards are available?

The flashcard set has 32 VIC Heavy Rigid Knowledge Test cards. Each card shows the term and its definition.

Which topics does the VIC Heavy Rigid Knowledge Test study material cover?

The VIC Heavy Rigid Knowledge Test study material has 6 sections, including Heavy Vehicle Licensing: Classes, Scope and Obligations, Pre-start checks, vehicle inspection and defects, and Inspection, Defects and Reporting.

What format facts does the catalog list for the VIC Heavy Rigid Knowledge Test exam?

The catalog lists these item types: multiple choice for the VIC Heavy Rigid Knowledge Test exam.