ASBOG FG PG Practice Test

ASBOG Fundamentals of Geology (FG) and Practice of Geology (PG) Examinations

ASBOG FG PG overview

  • 200 practice questions
  • 32 flashcards
  • 8 study guide topics
  • 36 key terms

What you'll study

  • General Geology and Earth Materials12%
  • Mineralogy, Petrology, and Geochemistry12%
  • Sedimentology, Stratigraphy, and Paleontology12%
  • Structural Geology and Tectonics12%
  • Geomorphology and Surficial Processes12%
  • Hydrogeology12%
  • Engineering Geology and Geohazards12%
  • Economic Geology and Energy Resources12%

ASBOG - the National Association of State Boards of Geology - is a national association of state geology licensing boards whose stated mission is "to promote the competent practice of geology by delivering rigorous licensure examinations, expanding license availability and mobility, and fostering academic training that protects public health, safety, and welfare." The Association administers the geology licensure examinations used by its member boards in regulated states, commonly referred to as the Fundamentals of Geology (FG) and Practice of Geology (PG) examinations. The FG exam is generally the entry-level examination for candidates completing or recently completing a geoscience degree; the PG exam is the practice-level examination tied to professional experience requirements set by the individual state board. Both are built from published examination blueprints covering the breadth of geological practice, from earth materials and structure through hydrogeology, engineering geology, and energy and mineral resources. Preparation guidance, blueprints, and a prep course are offered through ASBOG's Examinations and Educator pages, but applications, eligibility, fees, scheduling, and scoring are handled through the licensing board in the state where you are seeking licensure. This page is independent study material and is not affiliated with or endorsed by ASBOG or any state board.

Common mistakes

Computes hydraulic conductivity or transmissivity but leaves units inconsistent - e.g., plugs feet/day values into a formula expecting m/d, or mixes gpd/ft² with ft/day without converting, and reports a number without checking magnitude.

Candidates memorize T = Kb and Darcy's law as symbol strings, then substitute numbers from the prompt without tracking dimensions; the exam deliberately mixes unit systems (gpd, cfs, ft, m, gal) to test this.

What to do instead

Write the unit next to every number before calculating, convert everything to one consistent system (typically ft/day or m/day) in a first step, and sanity-check the answer's order of magnitude (K for sand is ~10⁻³ to 10 ft/day, not 10⁶).

Determines groundwater flow direction parallel to water-table contours, or averages the head at three wells instead of solving the three-point problem geometrically.

Flow-direction questions look like simple arithmetic; candidates skip the step of constructing contours or perpendiculars and answer with the steepest single gradient between two arbitrary wells.

What to do instead

Always sketch the three well locations to scale, interpolate the head value equal to the intermediate well along the line joining the high and low wells, draw the contour through that point and the intermediate well, then draw flow perpendicular to the contour, downgradient.

Records strike and dip using the wrong-handed convention, or computes apparent dip from a cross-section without resolving the angle between the section line and true dip direction.

Left-hand vs right-hand rule and the cosine relationship for apparent dip are easy to state but are applied under time pressure without a sketch, so the section azimuth is ignored.

What to do instead

Draw a compass rose with the bedding plane and section line on every structure problem; use tan(apparent dip) = tan(true dip) × sin(angle between section line and strike), and state the right-hand rule explicitly before writing the answer.

Assigns a fault type to a stress regime or plate boundary by name-matching (e.g., calling a transform boundary 'thrust' because it is convergent) rather than reasoning from the principal stress directions.

Candidates memorize boundary-fault pairs as lists, and the exam phrases questions in terms of σ1 orientation or local structures, which breaks the memorized pairing.

What to do instead

Derive fault type from σ1: vertical σ1 = normal, horizontal σ1 with vertical σ3 = thrust/reverse, both horizontal = strike-slip. Then map boundary type to stress field, not directly to fault name.

Classifies an igneous rock from its colour index or a single mineral (e.g., 'dark and shiny = basalt') instead of plotting modal mineralogy on QAPF or applying Bowen's reaction series to interpret texture and sequence.

Hand-specimen habits from lab are faster than modal counting, and Bowen's series is memorized as an order rather than used to explain zoning, resorption, or disequilibrium textures.

What to do instead

For classification questions, identify quartz, alkali feldspar, and plagioclase proportions first and place the rock on the QAPF diagram; use Bowen's series to explain observed textures (zoned plagioclase, reaction rims) rather than to name the rock.

Identifies minerals by colour or 'look' rather than by diagnostic properties, and fails to distinguish look-alikes such as quartz vs calcite vs halite, or hornblende vs augite.

Colour is the most salient property and the easiest to recall, but it is the least diagnostic; candidates underuse cleavage, hardness, streak, and reaction with acid under exam conditions.

What to do instead

Run a fixed checklist for every mineral question - hardness, cleavage/fracture, lustre, streak, acid reaction, and crystal form - and eliminate look-alikes on at least two properties before choosing.

Applies the Dunham classification to a carbonate described only by grain size, or reads a vertical stratigraphic column as a single continuous deepening without checking for parasequence stacking and flooding surfaces.

Dunham's terms (mudstone, wackestone, packstone, grainstone) sound like textural/grain-size terms, and stratigraphic columns are read top-to-bottom as a story rather than analysed for stacking patterns.

What to do instead

Use Dunham only when the描述 specifies mud support vs grain support; for stratigraphy, mark flooding surfaces and note whether facies stack coarsening-upward (progradation) or fining-upward (transgression) before interpreting sea-level change.

Calculates slope factor of safety using total normal stress and ignores pore-water pressure, or treats liquefaction potential as a function of grain size alone without considering saturation, density, and drainage.

Textbook FoS = resisting/ driving forces is applied with the simplest block model; the effective-stress principle is understood conceptually but not carried into the arithmetic under time pressure.

What to do instead

Always write the effective-stress form (τ = c' + (σ − u)tanφ') first, compute u from the water table or seepage condition, and for liquefaction check all three preconditions - loose, saturated, and rapid loading (or no drainage).

Identifies a drainage pattern or landform from a single descriptive keyword (e.g., 'dendritic' for any branching stream) without matching it to the underlying bedrock/structural control described in the stem.

Landform names are learned as vocabulary lists with picture associations, but the exam supplies only text descriptions of lithology, structure, and topography.

What to do instead

Extract the controlling variable from the stem - uniform resistant rock (dendritic), alternating resistant/weak beds (trellis), domed upland (radial), fractured granite (rectangular) - and choose the pattern from the control, not the keyword.

Matches an ore deposit to a tectonic setting or host rock from a memorized list (e.g., all porphyry deposits to 'convergent margins' without distinguishing the intrusive host, alteration zoning, or metal association), or confuses VMS with SEDEX.

Deposit-type lists are memorized as one-to-one pairs, but exam items describe alteration assemblages, host lithology, and metal ratios and expect the candidate to reason to the deposit class.

What to do instead

Build a table with four columns per deposit type - tectonic setting, host rock, alteration/mineralogy, and metal association - and answer from the diagnostic features given in the stem (e.g., seafloor exhalative vs basinal brine).

Exam requirements can change. Confirm current details with the exam provider.

ASBOG FG PG practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1General Geology and Earth Materials

    Which mineral has a Mohs hardness of 7, so that it scratches orthoclase but is itself scratched by corundum?

    1. Topaz
    2. Apatite
    3. Calcite
    4. Quartz Correct answer.

    Explanation

    The Mohs scale runs talc 1, gypsum 2, calcite 3, fluorite 4, apatite 5, orthoclase 6, quartz 7, topaz 8, corundum 9, diamond 10. Quartz therefore scratches orthoclase but is scratched by topaz and corundum.

  2. Question 2General Geology and Earth Materials

    At which type of plate boundary does new oceanic lithosphere form?

    1. A continental collision zone
    2. A convergent boundary with subduction
    3. A divergent mid-ocean ridge boundary Correct answer.
    4. A transform boundary with strike-slip motion

    Explanation

    Divergent boundaries are where plates move apart and mantle upwelling fills the gap, generating new basaltic crust that cools and thickens into lithosphere. Convergent and transform boundaries consume or slide past lithosphere rather than create it.

  3. Question 3General Geology and Earth Materials

    Which common sedimentary rock consists dominantly of calcium carbonate and effervesces vigorously in dilute hydrochloric acid?

    1. Shale
    2. Quartz sandstone
    3. Chert
    4. Limestone Correct answer.

    Explanation

    Limestone is composed mainly of calcite or aragonite, which reacts with acid to release carbon dioxide and produce visible fizzing. Sandstone and chert are silica-dominated, and shale is dominated by clay minerals, so none of these reacts strongly.

  4. Question 4General Geology and Earth Materials

    In an undeformed sequence of sedimentary strata, the principle of superposition states that:

    1. Each bed is younger than the one directly below it Correct answer.
    2. Fossils in every layer must belong to the same species
    3. The oldest layers are always found at the top of the sequence
    4. All layers were originally deposited as horizontal beds

    Explanation

    Superposition holds that in an undisturbed succession, beds were deposited in order from bottom to top, so age decreases upward. The idea that beds were originally horizontal is the principle of original horizontality, a separate principle.

  5. Question 5General Geology and Earth Materials

    The seismic boundary separating Earth's crust from the mantle is called the:

    1. Lehmann discontinuity
    2. Conrad discontinuity
    3. Gutenberg discontinuity
    4. Moho discontinuity Correct answer.

    Explanation

    The crust-mantle boundary is the Mohorovičić (Moho) discontinuity, marked by an abrupt jump in P-wave velocity at roughly 5 to 70 km depth. The Gutenberg marks the core-mantle boundary and the Lehmann lies within the core.

  6. Question 6General Geology and Earth Materials

    Which of the following is an example of chemical weathering?

    1. Root wedging along a bedrock fracture
    2. Abrasion of clasts in a river channel
    3. Frost wedging of granite along joints
    4. Dissolution of limestone by acid Correct answer.

    Explanation

    Chemical weathering involves mineral breakdown by reaction with water, acids, or oxygen; acid dissolution of calcite is a direct chemical reaction. Frost wedging, abrasion, and root wedging are all physical processes that break rock without changing its mineralogy.

  7. Question 7General Geology and Earth Materials

    A fault in which the hanging wall has moved down relative to the footwall is called a:

    1. A thrust fault
    2. A strike-slip fault
    3. A normal fault Correct answer.
    4. A reverse fault

    Explanation

    Normal faults form under extension, with the hanging wall dropping along a steeply dipping surface. Reverse and thrust faults show the opposite sense of slip and form under compression.

  8. Question 8General Geology and Earth Materials

    Which magma composition most commonly produces highly explosive eruptions?

    1. Komatiitic
    2. Rhyolitic Correct answer.
    3. Andesitic
    4. Basaltic

    Explanation

    High-silica rhyolitic magma is polymerized, viscous, and volatile-rich, so gas cannot escape easily and pressure builds until it fragments the magma explosively. Basaltic and komatiitic magmas are fluid and typically erupt effusively.

  9. Question 9General Geology and Earth Materials

    According to Bowen's reaction series, which mineral crystallizes first from a cooling basaltic magma?

    1. Olivine Correct answer.
    2. Quartz
    3. Biotite
    4. Muscovite

    Explanation

    Bowen's series places olivine and calcium-rich plagioclase at the highest-temperature end, crystallizing first from a mafic melt. Quartz and muscovite appear at the low-temperature end, late in crystallization or in more felsic melts.

  10. Question 10General Geology and Earth Materials

    Which metamorphic facies, diagnostic of subduction of basaltic crust at high pressure and low temperature, contains garnet and omphacitic pyroxene?

    1. Eclogite Correct answer.
    2. Hornblende hornfels
    3. Greenschist
    4. Zeolite

    Explanation

    Eclogite is the high-pressure, low-thermal-gradient assemblage of garnet plus omphacite formed from mafic rock in subduction zones. Hornfels, greenschist, and zeolite facies form at much lower pressures.

  11. Question 11General Geology and Earth Materials

    In a meandering stream, where is erosion concentrated?

    1. The channel floor at the thalweg
    2. The cut bank on the outer bank Correct answer.
    3. The point bar on the inner bank
    4. The floodplain behind the levee

    Explanation

    Flow is fastest and deepest on the outside of a meander bend, so the outer (cut) bank is eroded while sediment is deposited on the inner point bar. This lateral migration is what allows meanders to grow and migrate.

  12. Question 12General Geology and Earth Materials

    A mineral separate contains 25% of the parent isotope and 75% of its daughter product, and the parent half-life is 100 million years. Assuming no initial daughter, the age is:

    1. 200 Ma Correct answer.
    2. 400 Ma
    3. 100 Ma
    4. 25 Ma

    Explanation

    A remaining parent fraction of 25% corresponds to two half-lives, because each half-life halves the parent (100% to 50% to 25%). Two half-lives of 100 Ma each give an age of 200 Ma.

  13. Question 13General Geology and Earth Materials

    A sandstone composed of well-rounded, well-sorted quartz grains with almost no clay matrix is best described as:

    1. Neither texturally nor compositionally mature
    2. Texturally and compositionally mature Correct answer.
    3. Compositionally immature but texturally mature
    4. Texturally immature but compositionally mature

    Explanation

    Textural maturity reflects good sorting, rounding, and little fine matrix, while compositional maturity reflects loss of unstable grains so that quartz dominates. This rock satisfies both criteria.

  14. Question 14General Geology and Earth Materials

    In an anticline, the oldest exposed rocks occur:

    1. On the limbs of the fold
    2. In the hinge of the adjacent syncline
    3. Along the fold axis at depth only
    4. In the core of the fold Correct answer.

    Explanation

    Anticlines are convex-upward folds, so erosion exposes progressively older stratigraphic units toward the fold core. Synclines show the reverse pattern, with the youngest rocks in the core.

  15. Question 15General Geology and Earth Materials

    Which fossil group is the most useful index fossil for worldwide correlation of marine Jurassic strata?

    1. Stromatolites
    2. Ammonites Correct answer.
    3. Trilobites
    4. Rugose corals

    Explanation

    Ammonites were rapidly evolving, widely dispersed free-swimming cephalopods with a Jurassic record divided into fine, recognizable zones. Trilobites had largely declined by the Jurassic, and corals and stromatolites are long-ranging.

  16. Question 16General Geology and Earth Materials

    S-waves cannot pass through the outer core because:

    1. The outer core has a density too low to support shear
    2. The outer core is too hot to transmit seismic energy
    3. The outer core is liquid and lacks shear strength Correct answer.
    4. The outer core is crystalline and reflects shear waves

    Explanation

    Shear waves require a material with rigidity, and liquids have zero shear strength, so S-waves cannot propagate through the liquid outer core. This produces the S-wave shadow zone beyond about 103 degrees from the epicenter.

  17. Question 17General Geology and Earth Materials

    Porphyry copper deposits are characteristically associated with:

    1. Felsic to intermediate intrusions at arcs Correct answer.
    2. Evaporite basins in arid continental interiors
    3. Carbonatite volcanoes on ancient cratons
    4. Layered mafic intrusions in stable cratons

    Explanation

    Porphyry systems form above shallow, water-rich granodioritic to quartz monzonitic intrusions in magmatic arcs, where hydrothermal fluids fracture the roof rocks and deposit sulfides. Layered mafic intrusions, evaporites, and carbonatites host different deposit types.

  18. Question 18General Geology and Earth Materials

    Which soil horizon is typically the zone of accumulation of clay, iron oxides, and other materials leached from overlying horizons?

    1. The O horizon
    2. The A horizon
    3. The B horizon Correct answer.
    4. The C horizon

    Explanation

    The B horizon is the subsoil zone of illuviation, where clays, iron and aluminum oxides, and carbonates accumulate after being leached downward. The A horizon is the zone of eluviation and organic enrichment.

  19. Question 19General Geology and Earth Materials

    The pattern of magnetic stripes on the seafloor is symmetrical about mid-ocean ridges because:

    1. New crust records reversals as it spreads symmetrically Correct answer.
    2. Compacted sediment records the field direction
    3. Field intensity varies systematically with latitude
    4. Seawater uniformly magnetizes the oceanic crust

    Explanation

    As basalt cools below the Curie temperature at the ridge, it acquires a remanent magnetization matching the field at that time; continued spreading carries the normally and reversely magnetized strips away on both sides. This produces the mirror-image anomaly pattern that supported seafloor spreading.

  20. Question 20General Geology and Earth Materials

    Which landform is diagnostic of continental glaciation?

    1. Alluvial fans at range fronts
    2. V-shaped stream valleys
    3. Point bars on floodplains
    4. U-shaped valleys with truncated spurs Correct answer.

    Explanation

    Glaciers erode broad U-shaped troughs and behead or truncate the interfluves (spurs) of pre-existing valleys. V-shaped valleys, point bars, and alluvial fans are produced by running water.

  21. Question 21General Geology and Earth Materials

    In the structural classification of silicates, single-chain minerals such as pyroxenes have a silicon-to-oxygen ratio of:

    1. 1:3 Correct answer.
    2. 1:4
    3. 2:7
    4. 1:2

    Explanation

    Pyroxenes have the formula unit Si2O6, giving Si:O of 1:3 because each tetrahedron shares two of its four oxygens with neighbors along the chain. Framework silicates approach 1:2 and isolated tetrahedra give 1:4.

  22. Question 22General Geology and Earth Materials

    A bed strikes east-west and dips 30 degrees to the south. In a vertical cross-section oriented N45E, the apparent dip is closest to:

    1. 30 degrees
    2. 45 degrees
    3. 15 degrees
    4. 22 degrees Correct answer.

    Explanation

    Apparent dip follows tan(apparent dip) = tan(true dip) x sin(beta), where beta is the angle between the section line and strike. Here beta is 45 degrees, so tan(30) x sin(45) = 0.577 x 0.707 = 0.408, giving about 22 degrees.

  23. Question 23General Geology and Earth Materials

    A granitic rock is strongly enriched in large-ion lithophile elements such as Rb, Ba, and K, strongly depleted in Nb and Ta, and shows a negative Eu anomaly. Which interpretation best fits these data?

    1. Arc magma with plagioclase fractionation Correct answer.
    2. A mantle plume with no crystal fractionation
    3. A mid-ocean-ridge source with no crustal input
    4. An ultramafic magma formed by closed-system melting

    Explanation

    Enrichment in large-ion lithophile elements with negative Nb-Ta anomalies is the classic subduction-related (arc) signature, reflecting fluids from the descending slab. A negative Eu anomaly requires removal of plagioclase, in which Eu2+ is compatible, so fractionation is also indicated.

  24. Question 24General Geology and Earth Materials

    A sandstone plots in the recycled orogen field of a Qt-F-L provenance diagram, with abundant quartz and sedimentary lithic fragments. This most likely indicates derivation from:

    1. A continental interior craton source
    2. A magmatic-arc source
    3. An oceanic island-arc source
    4. An uplifted fold-thrust belt of sedimentary rocks Correct answer.

    Explanation

    The recycled orogen field reflects quartz-rich detritus shed from uplifted and deformed sedimentary or metasedimentary successions, typically in fold-thrust belts. Craton sources plot toward the quartz pole with few lithics, and arc sources are feldspar- and volcanic-lithic-rich.

  25. Question 25General Geology and Earth Materials

    Two minerals in the same rock give different K-Ar ages, with hornblende older than biotite. The best explanation is that:

    1. The rock cooled almost instantaneously
    2. Biotite incorporated excess argon
    3. Hornblende has a higher closure temperature Correct answer.
    4. Hornblende lost argon during weathering

    Explanation

    K-Ar and Ar-Ar ages record cooling through a mineral-specific closure temperature, and hornblende retains argon at higher temperature than biotite. Slow cooling therefore yields an older hornblende age and a younger biotite age from the same rock.

  26. Question 26Mineralogy, Petrology, and Geochemistry

    Which mineral has a hardness of 9 on the Mohs scale?

    1. Talc
    2. Corundum Correct answer.
    3. Calcite
    4. Quartz

    Explanation

    The Mohs scale ranks minerals by relative scratch hardness, with talc at 1 and diamond at 10. Corundum defines hardness 9, while quartz is 7 and calcite is 3.

  27. Question 27Mineralogy, Petrology, and Geochemistry

    Olivine belongs to which silicate structural class?

    1. Isolated tetrahedra Correct answer.
    2. Double-chain silicate
    3. Sheet silicate
    4. Framework silicate

    Explanation

    Olivine is a nesosilicate, consisting of independent SiO4 tetrahedra linked by Mg and Fe cations. Framework silicates include quartz and feldspar, double-chain silicates include amphibole, and sheet silicates include mica and clay.

  28. Question 28Mineralogy, Petrology, and Geochemistry

    Which mineral typically exhibits perfect basal cleavage?

    1. Quartz
    2. Muscovite Correct answer.
    3. Pyroxene
    4. Calcite

    Explanation

    Muscovite is a sheet silicate whose weak interlayer bonds cause it to split into thin flexible sheets parallel to the basal plane. Quartz lacks cleavage, calcite has rhombohedral cleavage, and pyroxene has two cleavages near 90 degrees.

  29. Question 29Mineralogy, Petrology, and Geochemistry

    According to Bowen's reaction series, which mineral crystallizes first from a cooling mafic magma?

    1. Olivine Correct answer.
    2. Muscovite
    3. Biotite
    4. Quartz

    Explanation

    The discontinuous branch of Bowen's reaction series begins with olivine at the highest temperature and progresses through pyroxene, amphibole, and biotite. Quartz and muscovite crystallize at much lower temperatures.

  30. Question 30Mineralogy, Petrology, and Geochemistry

    Which clastic sedimentary rock consists dominantly of rounded pebble-size clasts?

    1. Fossiliferous limestone
    2. Conglomerate Correct answer.
    3. Calcareous shale
    4. Quartz arenite

    Explanation

    Conglomerate is defined by rounded gravel-size clasts, whereas breccia is similar but has angular clasts. Quartz arenite is a sandstone, and limestone and shale are not gravel-dominated clastic rocks.

  31. Question 31Mineralogy, Petrology, and Geochemistry

    Which metamorphic rock forms primarily from the metamorphism of limestone?

    1. Schist
    2. Marble Correct answer.
    3. Quartzite
    4. Slate

    Explanation

    Marble is the metamorphic product of limestone or dolostone and is composed mainly of recrystallized calcite or dolomite. Quartzite forms from quartz sandstone, whereas slate and schist typically form from shale or mudstone.

  32. Question 32Mineralogy, Petrology, and Geochemistry

    Which mineral group is most abundant in Earth's continental crust?

    1. Oxides
    2. Feldspars Correct answer.
    3. Carbonates
    4. Sulfides

    Explanation

    Feldspars make up roughly half of continental crustal volume, and silicates as a whole dominate crustal mineralogy. Carbonates, sulfides, and oxides are important but much less abundant in the bulk crust.

  33. Question 33Mineralogy, Petrology, and Geochemistry

    Which statement best defines a mineral?

    1. A synthetic crystalline compound
    2. A natural crystalline inorganic solid Correct answer.
    3. An organic solid with variable composition
    4. Any solid material found in rocks

    Explanation

    A mineral is naturally occurring, inorganic, and crystalline, with a definite chemical composition that may vary within limits through solid solution. Synthetic compounds, organic materials, and noncrystalline solids do not satisfy the definition.

  34. Question 34Mineralogy, Petrology, and Geochemistry

    An igneous rock with an aphanitic texture most likely formed by which process?

    1. Rapid cooling at or near the surface Correct answer.
    2. Complete remelting of country rock
    3. Solid-state recrystallization
    4. Very slow cooling at depth

    Explanation

    Aphanitic textures are fine-grained because many small crystals nucleate during rapid cooling, commonly in volcanic or shallow intrusive settings. Slow cooling at depth produces coarse-grained phaneritic textures instead.

  35. Question 35Mineralogy, Petrology, and Geochemistry

    Blueschist-facies metamorphism is most characteristic of which setting?

    1. High-pressure, high-temperature lower crust
    2. High-pressure, low-temperature subduction zone Correct answer.
    3. Low-pressure, high-temperature contact aureole
    4. Medium-pressure, medium-temperature regional setting

    Explanation

    Blueschist facies is marked by glaucophane and lawsonite, which require high pressure and low temperature, conditions found along subduction zones. Contact metamorphism produces hornblende hornfels or sanidinite facies at low pressure and high temperature.

  36. Question 36Mineralogy, Petrology, and Geochemistry

    Which element is most incompatible during partial melting of the mantle?

    1. Ni
    2. Mg
    3. Cr
    4. Rb Correct answer.

    Explanation

    Rb is a large-ion lithophile element that preferentially enters the melt, so it is highly incompatible in mantle minerals. Ni, Cr, and Mg are compatible and concentrate in olivine, pyroxene, and spinel in the residue.

  37. Question 37Mineralogy, Petrology, and Geochemistry

    In foraminiferal calcite, a higher delta-18O value generally indicates which condition?

    1. Cooler water or more ice Correct answer.
    2. Lower seawater pH from dissolved CO2
    3. Higher salinity with no temperature change
    4. Warmer seawater at constant ice volume

    Explanation

    Oxygen isotope fractionation between calcite and seawater is temperature dependent, with colder water producing higher delta-18O in calcite. Growth of continental ice sheets also removes light oxygen from the ocean, raising seawater and carbonate delta-18O.

  38. Question 38Mineralogy, Petrology, and Geochemistry

    A rock with a high Rb/Sr ratio will develop what Sr isotope composition over time?

    1. High 87Rb/86Sr only after melting
    2. No change in Sr isotopes
    3. Low 87Sr/86Sr over time
    4. High 87Sr/86Sr over time Correct answer.

    Explanation

    Rubidium-87 decays to strontium-87, so a high parent-to-daughter ratio produces greater radiogenic 87Sr ingrowth with time. This is the basis for Rb-Sr isochron dating and for using initial Sr ratios as petrogenetic tracers.

  39. Question 39Mineralogy, Petrology, and Geochemistry

    A positive europium anomaly in an igneous rock most likely indicates what process?

    1. Removal of plagioclase by fractionation
    2. Derivation from a garnet-rich source
    3. Olivine accumulation
    4. Plagioclase accumulation Correct answer.

    Explanation

    Eu can occur as Eu2+ and substitute for Ca2+ in plagioclase, so plagioclase-rich cumulates develop positive Eu anomalies. Fractional crystallization that removes plagioclase leaves the residual melt with a negative Eu anomaly.

  40. Question 40Mineralogy, Petrology, and Geochemistry

    At the eutectic point of a binary system at fixed pressure, which situation applies?

    1. Complete solid solution between phases
    2. Two solids plus liquid coexist Correct answer.
    3. No liquid is present
    4. Only one phase is stable

    Explanation

    The eutectic is the lowest-temperature melt point in a binary system, where two solid phases and liquid coexist at a fixed temperature and melt composition for a given pressure. The phase rule gives zero degrees of freedom at that point when pressure is fixed.

  41. Question 41Mineralogy, Petrology, and Geochemistry

    What is the coordination number of silicon in the silicate tetrahedron?

    1. 3
    2. 2
    3. 4 Correct answer.
    4. 6

    Explanation

    Each silicon atom in a silicate tetrahedron is bonded to four oxygen atoms, giving a coordination number of 4. This SiO4 tetrahedron is the fundamental building block of all silicate minerals.

  42. Question 42Mineralogy, Petrology, and Geochemistry

    Which clay mineral generally has the highest cation exchange capacity?

    1. Kaolinite
    2. Chlorite
    3. Smectite Correct answer.
    4. Illite

    Explanation

    Smectite has a high layer charge and an expandable interlayer that adsorbs exchangeable cations, giving it a high cation exchange capacity. Kaolinite has little substitution and low capacity, whereas illite and chlorite are intermediate or lower.

  43. Question 43Mineralogy, Petrology, and Geochemistry

    Hydrolysis of potassium feldspar during weathering mainly produces which materials?

    1. Clay minerals and ions Correct answer.
    2. Pyrite and hematite
    3. Dolomite and gypsum
    4. Calcite and quartz

    Explanation

    Hydrolysis breaks down feldspar by reaction with water and carbonic acid, producing clay minerals plus dissolved potassium, silica, and other ions. This process is a major control on soil clay formation and natural water chemistry.

  44. Question 44Mineralogy, Petrology, and Geochemistry

    A porphyritic igneous texture most directly indicates what cooling history?

    1. Shock metamorphism
    2. Slow cooling throughout
    3. Complete melting
    4. Two-stage cooling history Correct answer.

    Explanation

    Porphyritic texture records early slow growth of large phenocrysts followed by more rapid cooling that forms a finer-grained groundmass. This two-stage history is common in magmas that ascend and crystallize at shallower levels.

  45. Question 45Mineralogy, Petrology, and Geochemistry

    Which mineral is a typical index mineral for amphibolite-facies pelitic rocks?

    1. Garnet Correct answer.
    2. Lawsonite
    3. Zeolite
    4. Chlorite

    Explanation

    In pelitic rocks, garnet appears with increasing metamorphic grade and is characteristic of amphibolite-facies assemblages along with staurolite, kyanite, or sillimanite. Chlorite indicates greenschist facies, lawsonite indicates blueschist facies, and zeolites indicate very low-grade conditions.

  46. Question 46Mineralogy, Petrology, and Geochemistry

    Which sulfide mineral is the principal ore of lead?

    1. Magnetite
    2. Sphalerite
    3. Chalcopyrite
    4. Galena Correct answer.

    Explanation

    Galena has the formula PbS and is the main lead ore mineral, commonly associated with sphalerite in hydrothermal deposits. Sphalerite is the main zinc ore, and chalcopyrite is the main copper ore.

  47. Question 47Mineralogy, Petrology, and Geochemistry

    In optical mineralogy, pleochroism refers to which behavior?

    1. Simple twinning
    2. Color change during stage rotation Correct answer.
    3. Relief change during rotation
    4. Extinction at 90 degrees

    Explanation

    Pleochroism is the change in color or absorption when a mineral is rotated under plane-polarized light, reflecting anisotropic absorption in different crystallographic directions. It is common in minerals such as biotite, hornblende, and tourmaline.

  48. Question 48Mineralogy, Petrology, and Geochemistry

    A magma containing about 65 wt% SiO2 is best classified as what composition?

    1. Felsic Correct answer.
    2. Mafic
    3. Intermediate
    4. Ultramafic

    Explanation

    Igneous compositions are commonly divided by silica content: ultramafic below about 45 wt%, mafic at 45-52 wt%, intermediate at 52-63 wt%, and felsic above about 63 wt%. A value near 65 wt% SiO2 therefore falls in the felsic field.

  49. Question 49Mineralogy, Petrology, and Geochemistry

    A trace-element partition coefficient greater than 1 means what?

    1. The element prefers solid Correct answer.
    2. The element is volatile
    3. The element prefers melt
    4. The element is radioactive

    Explanation

    The partition coefficient is the concentration in the solid divided by the concentration in the melt. A value greater than 1 indicates compatible behavior, meaning the element preferentially enters the solid phase.

  50. Question 50Mineralogy, Petrology, and Geochemistry

    Which fine-grained, foliated metamorphic rock forms from low-grade metamorphism of shale?

    1. Hornfels
    2. Quartzite
    3. Slate Correct answer.
    4. Marble

    Explanation

    Slate is a low-grade foliated metamorphic rock derived mainly from shale and characterized by slaty cleavage. Marble and quartzite are nonfoliated metamorphic rocks from limestone and quartz sandstone, respectively.

  51. Question 51Sedimentology, Stratigraphy, and Paleontology

    On the Wentworth grain-size scale, the sand-size range is:

    1. 2 to 64 mm
    2. less than 0.004 mm
    3. 0.004 to 0.0625 mm
    4. 0.0625 to 2 mm Correct answer.

    Explanation

    The Wentworth scale places sand between 1/16 mm (0.0625 mm) and 2 mm, spanning very fine to very coarse sand. Material finer than 0.0625 mm is silt and clay, and material coarser than 2 mm is granule or larger gravel.

  52. Question 52Sedimentology, Stratigraphy, and Paleontology

    A bed whose grain size decreases systematically from base to top records:

    1. Deposition from a steadily increasing current
    2. Intense post-depositional bioturbation
    3. Deposition from a steadily waning current Correct answer.
    4. Subaerial desiccation of a mud layer

    Explanation

    Graded bedding forms because the competence of the transporting current declines with time, so coarser particles settle first and finer particles settle last. The result is a bed that is coarse at the base and fine at the top.

  53. Question 53Sedimentology, Stratigraphy, and Paleontology

    In Dunham's classification of limestones, a mud-supported rock containing more than 10 percent grains is a:

    1. grainstone
    2. packstone
    3. boundstone
    4. wackestone Correct answer.

    Explanation

    Dunham's scheme separates mud-supported from grain-supported textures: wackestone is mud-supported with more than 10 percent grains, whereas mudstone is mud-supported with fewer than 10 percent grains. Grain-supported textures with mud are packstone and without mud are grainstone.

  54. Question 54Sedimentology, Stratigraphy, and Paleontology

    Chalk is a fine-grained limestone composed mainly of:

    1. coral fragments
    2. coccoliths Correct answer.
    3. detrital clay minerals
    4. mollusk shell hash

    Explanation

    Chalk is lithified pelagic carbonate ooze consisting dominantly of calcareous nannofossils, chiefly coccoliths, commonly with planktonic foraminifera. Its very fine grain size and low hardness reflect this nannofossil composition.

  55. Question 55Sedimentology, Stratigraphy, and Paleontology

    The principle stating that a sedimentary layer originally extended laterally in all directions until it thinned or reached the basin margin is the principle of:

    1. cross-cutting relationships
    2. lateral continuity Correct answer.
    3. original horizontality
    4. superposition

    Explanation

    The principle of lateral continuity holds that a layer of sediment spreads out laterally until it pinches out against the basin edge or terminates at a barrier. Matching separated outcrops of the same unit relies on this principle.

  56. Question 56Sedimentology, Stratigraphy, and Paleontology

    A clastic sedimentary rock composed of gravel-size, angular fragments is called:

    1. quartz arenite
    2. conglomerate
    3. breccia Correct answer.
    4. arkose

    Explanation

    Breccia and conglomerate both contain gravel-size clasts; the distinguishing criterion is rounding, with breccia having angular clasts and conglomerate having rounded clasts. Angular clasts imply little transport or a nearby source.

  57. Question 57Sedimentology, Stratigraphy, and Paleontology

    Red beds most commonly indicate deposition under:

    1. Evaporitic lagoonal conditions
    2. Stagnant reducing marine conditions
    3. High-grade metamorphic conditions
    4. Oxidizing continental conditions Correct answer.

    Explanation

    Red coloration comes from ferric iron oxide and hydroxide coatings on grains, which form where sediment is exposed to oxygen. Such oxidizing conditions are typical of terrestrial settings such as alluvial fans, fluvial plains, and deserts.

  58. Question 58Sedimentology, Stratigraphy, and Paleontology

    Which of the following is a trace fossil?

    1. A shark tooth
    2. A piece of petrified wood
    3. A Cruziana burrow Correct answer.
    4. An ammonite shell

    Explanation

    Trace fossils record organism behavior rather than body parts, and Cruziana is a well-known burrow produced by arthropods. Shells, teeth, and petrified wood are body fossils or body-part remains.

  59. Question 59Sedimentology, Stratigraphy, and Paleontology

    A sandstone with well-sorted, well-rounded, nearly spherical quartz grains most likely records:

    1. Deposition very close to the source area
    2. Direct chemical precipitation from seawater
    3. Long transport and repeated reworking Correct answer.
    4. Rapid deposition from a debris flow

    Explanation

    Rounding, sorting, and sphericity all increase as grains are transported and reworked, so a well-rounded, well-sorted sand reflects a long transport history and textural maturity. Such a deposit is typical of beaches, dunes, and mature fluvial systems.

  60. Question 60Sedimentology, Stratigraphy, and Paleontology

    Walther's Law states that in a conformable vertical succession, changes in facies reflect:

    1. Diagenetic replacement of one lithology by another
    2. Lateral migration over time of environments that were once side by side Correct answer.
    3. Random sea-level fluctuations with no lateral counterpart
    4. Faulting that juxtaposed unrelated facies

    Explanation

    Walther's Law links vertical and lateral facies changes: only those facies that are laterally adjacent can be superimposed vertically in a conformable succession. The vertical change therefore records the migration of depositional environments through time.

  61. Question 61Sedimentology, Stratigraphy, and Paleontology

    From base to top, a complete Bouma sequence consists of:

    1. Ripple lamination, massive sand, parallel lamination, mud
    2. Parallel lamination, massive sand, pelagic mud, ripple lamination
    3. Mud, parallel lamination, ripple lamination, massive sand
    4. Massive sand, parallel lamination, ripple lamination, pelagic mud Correct answer.

    Explanation

    The Bouma sequence records deposition from a single waning turbidity current: a massive or graded sandy division at the base, then plane-parallel lamination, then ripple cross-lamination, and finally hemipelagic mud at the top. Grain size and flow energy decrease upward through the sequence.

  62. Question 62Sedimentology, Stratigraphy, and Paleontology

    A sequence boundary on a shelf is best recognized by:

    1. A gradual upward deepening of the facies succession
    2. A uniform blanket of tabular cross-bedded sandstone
    3. A thin condensed interval of pelagic clay and phosphate
    4. An erosional surface with subaerial exposure Correct answer.

    Explanation

    Sequence boundaries form when relative sea level falls and the shelf is exposed, so they are marked by erosion, incised valleys, paleosols, or other evidence of subaerial exposure. Condensed sections and deepening trends instead characterize flooding surfaces and transgressive intervals.

  63. Question 63Sedimentology, Stratigraphy, and Paleontology

    A vertical succession from fluvial sandstone upward to shoreface sandstone and then offshore shale records:

    1. A marine transgression Correct answer.
    2. A marine regression
    3. A prograding delta lobe
    4. A fall in base level

    Explanation

    Upward deepening from continental to shoreface to offshore environments means the shoreline moved landward, which defines a transgression. Regression and progradation produce the reverse, an upward-shallowing succession.

  64. Question 64Sedimentology, Stratigraphy, and Paleontology

    During progressive evaporation of normal seawater, the first mineral to precipitate in abundance is:

    1. sylvite
    2. halite
    3. gypsum Correct answer.
    4. carnallite

    Explanation

    Evaporite minerals precipitate in order of increasing solubility: calcium carbonate first, then gypsum (or anhydrite), then halite, and finally the highly soluble potassium and magnesium salts such as sylvite and carnallite. Gypsum therefore precedes halite in the sequence.

  65. Question 65Sedimentology, Stratigraphy, and Paleontology

    Which feature best identifies an ancient aeolian sandstone?

    1. Herringbone cross-bedding
    2. Large high-angle cross-beds of rounded frosted grains Correct answer.
    3. Shell lags and bioturbation
    4. Fining-upward cycles with root traces

    Explanation

    Wind transports sand by saltation and builds steeply dipping dune forests, preserved as large-scale, high-angle tabular or trough cross-beds. Grain collisions in air produce well-rounded, frosted, and commonly very well-sorted grains.

  66. Question 66Sedimentology, Stratigraphy, and Paleontology

    Which character best distinguishes a tillite from a water-lain conglomerate?

    1. Graded beds capped by mudstone
    2. Imbricated clasts with cross-bedding
    3. Well-rounded clasts in a sandy matrix
    4. Massive, unsorted diamicton fabric Correct answer.

    Explanation

    Till is deposited directly by ice without sorting by water, so it forms a massive, extremely poorly sorted, matrix-supported diamicton, often with striated or faceted clasts. Water-lain gravels are typically better sorted, rounded, and stratified.

  67. Question 67Sedimentology, Stratigraphy, and Paleontology

    In a deeply buried sandstone, which process most directly destroys primary intergranular porosity?

    1. Feldspar dissolution
    2. Meteoric leaching
    3. Quartz overgrowth cementation Correct answer.
    4. Exhumation and unloading

    Explanation

    Cementation fills pore space with authigenic minerals, and quartz overgrowths are a major porosity-reducing phase during burial diagenesis, along with compaction. Dissolution and leaching, by contrast, generate secondary porosity.

  68. Question 68Sedimentology, Stratigraphy, and Paleontology

    The ideal index fossil has:

    1. A short stratigraphic range and wide geographic distribution Correct answer.
    2. A long stratigraphic range and wide geographic distribution
    3. A long stratigraphic range and narrow geographic distribution
    4. A short stratigraphic range and narrow geographic distribution

    Explanation

    A short stratigraphic range gives high temporal resolution, and a wide geographic distribution allows the fossil to be correlated between distant sections. Both properties together are what make a fossil useful for biostratigraphic zonation.

  69. Question 69Sedimentology, Stratigraphy, and Paleontology

    A surface where sedimentary strata rest directly on folded metamorphic rocks is a:

    1. angular unconformity
    2. nonconformity Correct answer.
    3. paraconformity
    4. disconformity

    Explanation

    A nonconformity separates sedimentary rocks from underlying igneous or metamorphic basement. In an angular unconformity, the rocks below the surface are themselves layered sedimentary units with a different dip.

  70. Question 70Sedimentology, Stratigraphy, and Paleontology

    A sandstone containing abundant vertical Skolithos and Ophiomorpha burrows most likely records:

    1. A muddy lagoon with stagnant bottom water
    2. A quiet, low-oxygen abyssal plain
    3. A rocky wave-cut platform with borers
    4. A shifting sandy shoreface in high energy Correct answer.

    Explanation

    The Skolithos ichnofacies is dominated by vertical and U-shaped dwelling burrows made by suspension feeders that must avoid burial in mobile sand. It is characteristic of high-energy, shallow-marine sandy substrates such as shorefaces and tidal inlets.

  71. Question 71Sedimentology, Stratigraphy, and Paleontology

    A retrogradational stacking pattern of parasequences bounded above by a marine flooding surface indicates:

    1. A lowstand systems tract
    2. A falling-stage systems tract
    3. A highstand systems tract
    4. A transgressive systems tract Correct answer.

    Explanation

    Retrogradational stacking means each successive parasequence steps landward, recording shoreline retreat during rising relative sea level. This landward-stepping geometry is the defining character of the transgressive systems tract.

  72. Question 72Sedimentology, Stratigraphy, and Paleontology

    A sandstone dominated by monocrystalline quartz with a zircon-tourmaline-rutile heavy-mineral suite most likely came from:

    1. A shallow carbonate platform
    2. A proximal volcanic arc
    3. A first-cycle plutonic source rich in feldspar
    4. A mature, polycyclic cratonic source Correct answer.

    Explanation

    High quartz content with a zircon-tourmaline-rutile suite indicates intense weathering and recycling, because unstable minerals have been destroyed and only durable ones survive. Such compositions are typical of sand derived from cratonic interiors or recycled older sandstones.

  73. Question 73Sedimentology, Stratigraphy, and Paleontology

    A dark, organic-rich shale containing graptolites and no benthic fossils was most likely deposited in:

    1. A tidal flat
    2. A high-energy beach
    3. A deep, poorly oxygenated marine basin Correct answer.
    4. An evaporitic lagoon

    Explanation

    Graptolites were planktonic organisms that settled into quiet water, and the absence of benthic fossils plus abundant organic matter points to oxygen-deficient bottom conditions. Together these indicate a deep, restricted marine basin with poor bottom circulation.

  74. Question 74Sedimentology, Stratigraphy, and Paleontology

    Aragonitic shells in ancient limestones are commonly preserved only as molds because aragonite is:

    1. the more stable polymorph under burial conditions
    2. dissolved only by acidic meteoric groundwater
    3. metastable and readily dissolved or inverted during diagenesis Correct answer.
    4. converted to dolomite before lithification

    Explanation

    Aragonite is a metastable polymorph of calcium carbonate that readily dissolves or inverts to calcite under diagenetic conditions. The shell is therefore commonly removed, leaving a mold, or replaced by calcite, so original aragonite is rarely preserved in old rocks.

  75. Question 75Sedimentology, Stratigraphy, and Paleontology

    An ooid grainstone with large-scale cross-beds on a rimmed carbonate shelf most likely accumulated:

    1. On a supratidal mudflat
    2. In a high-energy sand shoal at the platform margin Correct answer.
    3. In a euxinic starved basin
    4. In a quiet basinal setting below wave base

    Explanation

    Ooids form where currents or waves repeatedly roll grains in agitated, carbonate-saturated water, and cross-beds record migration of dunes and sand waves. Ooid grainstones therefore mark high-energy shoals, typically at platform margins or oolitic tidal bars.

  76. Question 76Structural Geology and Tectonics

    In a normal fault, the hanging wall moves in which direction relative to the footwall?

    1. Up
    2. Down Correct answer.
    3. Laterally, parallel to strike
    4. Up and toward the footwall

    Explanation

    Normal faults form in response to extension, so the hanging wall, the block above the inclined fault surface, drops relative to the footwall. The dip of the fault surface plus the sense of dip-slip motion define the fault as normal rather than reverse.

  77. Question 77Structural Geology and Tectonics

    A fold whose limbs dip away from the hinge line on both sides, with the oldest rocks exposed in the core, is called a(n):

    1. Anticline Correct answer.
    2. Basin
    3. Syncline
    4. Monocline

    Explanation

    An anticline is convex upward, so its limbs dip away from the hinge and the stratigraphically oldest units occupy the core. A syncline is the mirror image, with limbs dipping toward the hinge and the youngest rocks in the core.

  78. Question 78Structural Geology and Tectonics

    Mid-ocean ridges are the classic example of which type of plate boundary?

    1. Transform
    2. Divergent Correct answer.
    3. Convergent
    4. Oblique-slip

    Explanation

    New lithosphere is created at mid-ocean ridges as plates move apart, which is the defining behavior of a divergent boundary. Convergent boundaries consume lithosphere, and transform boundaries involve lateral sliding.

  79. Question 79Structural Geology and Tectonics

    The direction of strike of a planar bed is always:

    1. parallel to the direction of true dip
    2. the same as the dip direction
    3. the direction of maximum slope of the bed
    4. perpendicular to true dip Correct answer.

    Explanation

    Strike is the compass trend of the line formed where a plane intersects horizontal, and true dip is measured in the vertical plane at right angles to that line. Strike is therefore by definition perpendicular to the true dip direction.

  80. Question 80Structural Geology and Tectonics

    The block of rock that lies above an inclined fault surface is called the:

    1. Footwall
    2. Throw block
    3. Heave block
    4. Hanging wall Correct answer.

    Explanation

    The hanging wall is defined geometrically as the block above an inclined fault plane, and the footwall is the block below it. These terms are independent of the sense of slip.

  81. Question 81Structural Geology and Tectonics

    An angular unconformity in a stratigraphic section indicates that:

    1. faulting displaced the entire section after the younger unit was deposited
    2. the older unit was regionally metamorphosed before the younger unit was deposited
    3. deposition was continuous, with no break in sedimentation at that surface
    4. older strata were tilted and eroded before younger beds were deposited Correct answer.

    Explanation

    An angular unconformity requires that older strata be tilted or folded, then truncated by erosion, before younger, initially horizontal strata are laid down on the erosional surface. This truncation of dipping beds by a younger flat-lying unit is the diagnostic feature.

  82. Question 82Structural Geology and Tectonics

    A brittle fracture surface across which no visible offset parallel to the surface can be demonstrated is best termed a:

    1. Fault
    2. Joint Correct answer.
    3. Mylonite
    4. Shear zone

    Explanation

    A joint is a fracture with little or no displacement parallel to its surface, whereas a fault shows measurable slip. Both are brittle structures, but only the fault records shear offset.

  83. Question 83Structural Geology and Tectonics

    Deep-ocean trenches paired with volcanic arcs are characteristic of which tectonic setting?

    1. Mid-ocean ridge
    2. Continental rift
    3. Transform boundary
    4. Subduction zone Correct answer.

    Explanation

    Subduction zones consume oceanic lithosphere, producing a trench at the plate interface and a volcanic arc on the overriding plate above the descending slab. Ridges, rifts, and transform boundaries lack this arc-trench pairing.

  84. Question 84Structural Geology and Tectonics

    On a geologic map, a plunging anticline is recognized by:

    1. a V-shaped outcrop pattern closing in the direction of plunge, with oldest rocks inside Correct answer.
    2. a V-shaped outcrop pattern that closes opposite to the plunge direction, with youngest rocks in the core
    3. straight, parallel outcrop belts that trend at right angles to the fold axis and show no closure
    4. a closed circular outcrop pattern in which the youngest rocks occur at the center

    Explanation

    Plunging folds generate V-shaped outcrop traces whose apex points in the plunge direction. The stratigraphic identity of the rocks in the core distinguishes an anticline (oldest) from a syncline (youngest).

  85. Question 85Structural Geology and Tectonics

    In a crustal region where the maximum principal compressive stress is vertical, the resulting faulting is most likely to be:

    1. Strike-slip
    2. Reverse
    3. Thrust
    4. Normal Correct answer.

    Explanation

    When the greatest compressive stress is vertical, failure occurs by dropping the hanging wall, producing normal faults and crustal extension. Thrust and strike-slip faults require a horizontal maximum principal stress.

  86. Question 86Structural Geology and Tectonics

    Which sequence of fault rocks records progressively deeper, hotter conditions of deformation?

    1. fault breccia, then mylonite, then gouge
    2. gouge, then fault breccia, then cataclasite
    3. mylonite, then cataclasite, then fault breccia
    4. fault breccia, then cataclasite, then mylonite Correct answer.

    Explanation

    With increasing depth and temperature, deformation passes from brittle to ductile, giving a progression from fault breccia through cataclasite to mylonite. Grain size decreases and recrystallization becomes progressively more important.

  87. Question 87Structural Geology and Tectonics

    The overall style of deformation in a typical fold-and-thrust belt involves:

    1. horizontal shear with no significant change in crustal thickness
    2. shortening taken up by thrusts that dip gently toward the hinterland Correct answer.
    3. vertical uplift on steeply dipping strike-slip faults, with little shortening
    4. extension taken up by steep normal faults and crustal thinning

    Explanation

    Fold-and-thrust belts accommodate crustal shortening above a basal detachment, with thrusts that generally dip gently back toward the hinterland and ramp up toward the foreland. The net effect is crustal thickening, not thinning.

  88. Question 88Structural Geology and Tectonics

    The inclined zone of earthquake hypocenters that deepens beneath an island arc marks:

    1. a vertical strike-slip fault system cutting the arc
    2. the brittle-ductile transition beneath a rift basin
    3. the base of the continental crust beneath the arc
    4. the descending slab of subducting lithosphere Correct answer.

    Explanation

    The Wadati-Benioff zone is defined by hypocenters that deepen away from the trench, tracing the cold, brittle subducting slab into the mantle. Its dip reflects the geometry of the downgoing plate.

  89. Question 89Structural Geology and Tectonics

    Boudins form as a direct result of:

    1. extension of a competent layer within a less competent matrix Correct answer.
    2. simple shear parallel to layering with no extension of the layer
    3. layer-parallel shortening of a competent layer between two rigid blocks
    4. hydrofracturing driven by elevated pore-fluid pressure

    Explanation

    Boudins are segments of a competent layer that has been stretched and pulled apart within a weaker matrix, so they record extension parallel to layering. The gaps between segments are commonly filled by the matrix or by mineral veins.

  90. Question 90Structural Geology and Tectonics

    Axial-planar slaty cleavage in a folded sequence typically forms:

    1. parallel to the original bedding throughout the fold
    2. parallel to the axial surfaces of the folds Correct answer.
    3. at about 45 degrees to the fold axis everywhere in the fold
    4. restricted to the hinge zones of the folds

    Explanation

    Slaty cleavage is a tectonic fabric that develops perpendicular to the maximum shortening direction, which during folding is parallel to the axial surface. It therefore cuts across bedding except where the two happen to coincide near the hinge.

  91. Question 91Structural Geology and Tectonics

    In a dextral shear zone dominated by simple shear, Riedel (R) shears typically form:

    1. perpendicular to the shear-zone boundary, with pure dip-slip motion along them
    2. at about 15 to 20 degrees to the shear-zone boundary, with the same sense of shear Correct answer.
    3. at about 70 to 80 degrees to the shear-zone boundary, with the opposite sense of shear
    4. parallel to the shear-zone boundary, with no component of slip across them

    Explanation

    Riedel shears are synthetic fractures that nucleate early in a shearing rock mass, inclined at a small angle of roughly 15 to 20 degrees to the shear-zone boundary and slipping in the same sense as the zone. Antithetic shears form at higher angles and record the opposite sense of slip.

  92. Question 92Structural Geology and Tectonics

    A continental rift province is structurally characterized by:

    1. crustal extension, normal faulting, and basin formation Correct answer.
    2. crustal shortening, thrust faulting, and crustal thickening
    3. transcurrent motion on steeply dipping strike-slip faults
    4. subduction of oceanic lithosphere beneath a continental margin

    Explanation

    Continental rifts result from lithospheric extension, producing normal faults, half-grabens, and crustal thinning. The associated basins fill with syntectonic sediment as the rift develops.

  93. Question 93Structural Geology and Tectonics

    Chains of progressively older volcanic islands along a hotspot track primarily record:

    1. the age of the oceanic crust where it enters the trench
    2. the rate of sea-floor spreading at the adjacent mid-ocean ridge
    3. changes in the dip of the subducting slab through time
    4. the direction and rate of plate motion relative to the hotspot Correct answer.

    Explanation

    A hotspot is fixed relative to the deep mantle for long intervals, so as the plate moves over it, volcanism creates a chain of islands that get older away from the active center. The trend and age progression therefore record the direction and speed of plate motion.

  94. Question 94Structural Geology and Tectonics

    A monocline most commonly develops where:

    1. two separate fold trains interfere with one another
    2. folding is localized above a step or fault in a rigid basement Correct answer.
    3. a thick sedimentary section is shortened uniformly across a broad region
    4. the strata remain horizontal throughout the deformation

    Explanation

    A monocline is a steplike flexure of otherwise gently dipping strata, formed where the cover is forced to fold above a fault or step in the underlying rigid basement. The flexure commonly dies out upward into the overlying section.

  95. Question 95Structural Geology and Tectonics

    Slickenlines preserved on a fault surface record:

    1. the stratigraphic age of the youngest offset bed
    2. the temperature and pressure of deformation only
    3. the direction of slip on the fault plane Correct answer.
    4. the total finite strain of the adjacent wall rocks

    Explanation

    Slickenlines are grooves, striations, or mineral fibers aligned with the direction of movement on a fault surface, so they give the rake of slip on that plane. Slickenfibers can also indicate the sense of slip, not just its direction.

  96. Question 96Structural Geology and Tectonics

    A fault-bend fold develops where:

    1. a normal fault is reactivated during a later phase of extension
    2. an earlier fold is truncated by an angular unconformity
    3. a thrust sheet is forced over a step in the fault surface Correct answer.
    4. a thrust sheet is cut and offset by a steeply dipping tear fault

    Explanation

    A fault-bend fold forms when a thrust sheet climbs a ramp connecting two flats of the detachment; the hanging wall must fold to accommodate the change in fault dip. The fold geometry is dictated by the shape of the fault surface rather than by the slip magnitude alone.

  97. Question 97Structural Geology and Tectonics

    A pull-apart basin forms:

    1. in the hanging wall of a deeply buried thrust ramp
    2. at a restraining step-over along a strike-slip fault
    3. above a rising salt diapir in an extensional basin
    4. at a releasing step-over along a strike-slip fault Correct answer.

    Explanation

    A releasing step-over or bend creates local extension between two overlapping strike-slip segments, so the crust subsides and a rhomb-shaped pull-apart basin fills with sediment. A restraining step-over, by contrast, produces local shortening and uplift.

  98. Question 98Structural Geology and Tectonics

    Asymmetric recrystallized tails around porphyroclasts in a mylonite are most useful for determining:

    1. the sense of shear in the mylonite zone Correct answer.
    2. the absolute age of the deformation event
    3. the depth of burial during deformation only
    4. the original sedimentary bedding orientation

    Explanation

    The geometry of recrystallized tails, such as sigma and delta types, develops in a consistent relation to the sense of rotation during non-coaxial flow, so it records the shear sense of the enclosing zone. These are standard kinematic indicators in ductile shear zones.

  99. Question 99Structural Geology and Tectonics

    In progressive simple shear along a transform boundary, the fabric defined by the flattening plane rotates with increasing finite strain until it approaches an orientation:

    1. at about 45 degrees to the shear plane, regardless of finite strain
    2. perpendicular to the shear plane at all strains
    3. perpendicular to the shear direction
    4. parallel to the shear plane Correct answer.

    Explanation

    In simple shear the finite-strain long axis rotates toward the shear direction as strain accumulates, so at high shear strain the foliation lies nearly parallel to the shear plane. This is why strongly sheared rocks show foliation subparallel to the shear-zone boundary.

  100. Question 100Structural Geology and Tectonics

    An ophiolite suite preserved within a suture zone most directly records:

    1. intracontinental strike-slip faulting along a reactivated basement fabric
    2. emplacement of a mantle plume beneath an otherwise stable craton
    3. obduction of oceanic lithosphere during ocean closure Correct answer.
    4. rifting of a continental margin during incipient sea-floor spreading

    Explanation

    Ophiolites are fragments of oceanic lithosphere, typically including mantle peridotite, gabbro, sheeted dikes, and pillow basalts, emplaced onto continental crust. Their presence in a suture most commonly records obduction during closure of an ocean basin.

  101. Question 101Geomorphology and Surficial Processes

    Spheroidal weathering of jointed granite most commonly produces which feature?

    1. Planar bedding surfaces
    2. Columnar joints in basalt
    3. Slickensides along faults
    4. Corestones in saprolite Correct answer.

    Explanation

    Weathering attacks joint-bounded blocks from all sides, preferentially rounding corners and edges. The result is rounded corestones surrounded by weathered mantle.

  102. Question 102Geomorphology and Surficial Processes

    The steepest slope that loose, dry sand can maintain is called the:

    1. Plastic limit
    2. Liquid limit
    3. Angle of repose Correct answer.
    4. Optimum moisture content

    Explanation

    Dry granular material stands only until shear stress exceeds frictional resistance. That limiting slope is the angle of repose.

  103. Question 103Geomorphology and Surficial Processes

    An oxbow lake forms when:

    1. A tributary builds an alluvial fan
    2. A meander neck is cut off Correct answer.
    3. A glacier scours a bedrock basin
    4. A dam raises upstream base level

    Explanation

    Lateral erosion narrows the neck between two meander limbs until the river takes a shorter path across it. The abandoned loop remains as an oxbow lake.

  104. Question 104Geomorphology and Surficial Processes

    Which material is deposited directly by melting glacial ice without later reworking by water?

    1. Fine silt carried by wind
    2. Well-sorted sand from meltwater
    3. Unsorted debris left by ice Correct answer.
    4. Rounded gravel reworked by waves

    Explanation

    Till is deposited in place as ice melts and drops its entrained load. Because water does not sort it, till is typically unsorted and unstratified.

  105. Question 105Geomorphology and Surficial Processes

    A barchan dune typically forms under which conditions?

    1. A high water table with vegetation
    2. Limited sand and steady wind Correct answer.
    3. Abundant sand and shifting winds
    4. A bedrock ridge parallel to wind

    Explanation

    Barchans are crescent dunes that develop where sand supply is limited and wind direction is consistent. Their horns point downwind.

  106. Question 106Geomorphology and Surficial Processes

    Longshore drift moves sediment mainly:

    1. Inland by saltation
    2. Up the beach face at right angles
    3. Directly offshore into deep water
    4. Parallel to the shoreline Correct answer.

    Explanation

    Oblique wave approach drives a current along the shore that transports sediment parallel to the coastline. This process shapes spits and barrier islands.

  107. Question 107Geomorphology and Surficial Processes

    Sinkholes in limestone terrain are primarily caused by:

    1. Subsidence from oil withdrawal
    2. Collapse of lava tubes
    3. Dissolution of carbonate rock Correct answer.
    4. Glacial scour of bedrock

    Explanation

    Acidic groundwater dissolves limestone along joints and bedding planes, enlarging voids until the roof collapses. This produces solution and collapse sinkholes.

  108. Question 108Geomorphology and Surficial Processes

    Which soil horizon is typically the zone of greatest organic matter accumulation?

    1. C horizon Correct answer.
    2. A horizon
    3. O horizon
    4. B horizon

    Explanation

    The O horizon is the surface layer dominated by organic litter and humus. The A, B, and C horizons lie below and contain progressively less organic matter.

  109. Question 109Geomorphology and Surficial Processes

    A graded stream is best described as one where:

    1. Carries only suspended load
    2. Load equals transport capacity Correct answer.
    3. Has a perfectly straight channel
    4. Lacks a floodplain and banks

    Explanation

    A graded stream is in dynamic equilibrium, with sediment supply balanced by transport capacity. Its profile adjusts to maintain that balance.

  110. Question 110Geomorphology and Surficial Processes

    An esker is a ridge formed mainly by:

    1. Deposition at the ice margin
    2. Deposition beneath moving ice
    3. Deposition in a proglacial lake
    4. Subglacial stream deposition Correct answer.

    Explanation

    Eskers are sinuous ridges of sand and gravel deposited by meltwater streams flowing in tunnels beneath or within a glacier. They are later exposed after ice retreat.

  111. Question 111Geomorphology and Surficial Processes

    Wave refraction causes wave energy to:

    1. Converge in bays and diverge offshore
    2. Converge only during large storms
    3. Remain uniform along an irregular coast
    4. Converge on headlands Correct answer.

    Explanation

    Waves slow in shallow water, so crests bend toward headlands where the bottom rises. This concentrates energy on headlands and spreads it in bays.

  112. Question 112Geomorphology and Surficial Processes

    Loess is best described as:

    1. Wind-deposited silt Correct answer.
    2. Residual gravel
    3. Glacially transported clay
    4. Water-laid sand

    Explanation

    Loess consists of silt-sized particles transported by wind and deposited as a blanket. It is typically well sorted and can form steep bluffs.

  113. Question 113Geomorphology and Surficial Processes

    A slump differs from an earthflow mainly by its:

    1. Rotation on a curved failure plane Correct answer.
    2. Flow of saturated debris on a gentle slope
    3. Slow creep of soil over bedrock
    4. Free fall of rock from a cliff

    Explanation

    Slumps move as relatively coherent blocks along a curved, rotational failure surface. Earthflows are more fluid and lack a single rotational plane.

  114. Question 114Geomorphology and Surficial Processes

    A trellis drainage pattern typically develops on:

    1. A single large volcanic cone
    2. Flat-lying lava flows
    3. Folded beds of mixed hardness Correct answer.
    4. Uniformly resistant granite

    Explanation

    Trellis patterns form where folded sedimentary beds alternate in resistance. Main streams follow weaker beds, while short tributaries cut across resistant ridges.

  115. Question 115Geomorphology and Surficial Processes

    A knickpoint in a river's longitudinal profile most likely indicates:

    1. A long period of tectonic stability
    2. Uniform sediment supply along the channel
    3. Deposition in a former lake
    4. Base-level fall and incision Correct answer.

    Explanation

    A knickpoint marks a steep reach that migrates upstream as the river adjusts to lowered base level. It reflects renewed incision.

  116. Question 116Geomorphology and Surficial Processes

    The long axis of a drumlin is generally oriented:

    1. Parallel to the regional joint set
    2. Radial to the former ice center
    3. Perpendicular to ice flow
    4. Parallel to ice-flow direction Correct answer.

    Explanation

    Drumlins are streamlined till landforms shaped beneath moving ice. Their long axes align with the direction of former ice flow.

  117. Question 117Geomorphology and Surficial Processes

    Alluvial fans form mainly where:

    1. Wind erodes a bedrock depression
    2. A river enters a standing body of water
    3. A glacier retreats up a valley
    4. Stream gradient drops at a mountain front Correct answer.

    Explanation

    A stream leaving a steep mountain front loses gradient and spreads its load as a fan-shaped deposit. Rapid deposition occurs because transport capacity drops abruptly.

  118. Question 118Geomorphology and Surficial Processes

    Patterned ground in permafrost regions results mainly from:

    1. Slumping along a curved failure
    2. Freeze-thaw and frost heave Correct answer.
    3. Wind scour around obstacles
    4. Chemical solution of bedrock

    Explanation

    Repeated freezing and thawing, combined with frost heave and sorting, produces circles, polygons, and stripes in periglacial soils.

  119. Question 119Geomorphology and Surficial Processes

    Natural levees along a river form because:

    1. Erosion removes sediment from the banks
    2. Overbank deposition of coarse sediment Correct answer.
    3. Wind deposits sand along the channel
    4. Fine sediment settles in the thalweg

    Explanation

    During floods, water spreads over the banks and slows abruptly, depositing its coarsest suspended load near the channel. Repeated floods build raised levees.

  120. Question 120Geomorphology and Surficial Processes

    Speleothems such as stalactites form mainly by:

    1. Dissolution of dolomite
    2. Freezing of dripping water
    3. Evaporation of saline groundwater
    4. CO2 loss and calcite precipitation Correct answer.

    Explanation

    Drip water reaching a cave loses carbon dioxide, raising its pH and causing calcite to precipitate. Repeated precipitation builds stalactites and stalagmites.

  121. Question 121Geomorphology and Surficial Processes

    On a Hjulstrom diagram, clay-sized particles require a higher entrainment velocity than sand mainly because of:

    1. Clay particle cohesion Correct answer.
    2. Clay settles faster than gravel
    3. Clay particles are denser than sand
    4. Clay particles are larger than sand

    Explanation

    Fine clay particles stick together through electrostatic and van der Waals forces, so they resist entrainment despite their small size. This cohesion produces the upturn of the entrainment curve at the fine end.

  122. Question 122Geomorphology and Surficial Processes

    A pair of river terraces at the same elevation on opposite sides of a valley most likely represents:

    1. A fault scarp
    2. An abandoned floodplain Correct answer.
    3. A glacial end moraine
    4. A former lake shoreline

    Explanation

    Terraces are former floodplain surfaces left above the modern channel when the river incises. Matching elevations on both sides indicate a formerly continuous surface.

  123. Question 123Geomorphology and Surficial Processes

    A wave-dominated delta shoreline is typically characterized by:

    1. Smooth arcuate beaches with beach ridges Correct answer.
    2. Broad tidal mudflats without beaches
    3. Long distributary channels projecting seaward
    4. A deeply incised submarine canyon

    Explanation

    Waves rework delta-front sediment, smoothing the shoreline into an arcuate shape and building beach ridges. River-mouth deposits are redistributed along the coast.

  124. Question 124Geomorphology and Surficial Processes

    A hypsometric curve for a drainage basin shows:

    1. Longitudinal profile of the trunk stream
    2. Area above a given elevation Correct answer.
    3. Drainage density versus relief
    4. Sediment yield versus discharge

    Explanation

    The hypsometric curve plots the proportion of basin area above each elevation. Its shape reflects the balance of erosion and uplift in the landscape.

  125. Question 125Geomorphology and Surficial Processes

    Pediments are most likely to develop under which conditions?

    1. Glacial scour of a bedrock plateau
    2. Humid climate and deep weathering
    3. Arid climate and scarp retreat Correct answer.
    4. Wave erosion of a coastal cliff

    Explanation

    Pediments are gently sloping bedrock surfaces formed by backwasting of mountain fronts in arid to semiarid regions. Sheetflow and weathering remove material and extend the surface.

  126. Question 126Hydrogeology

    A sediment has a total porosity of 35% and a specific retention of 10%. What is its specific yield?

    1. 35%
    2. 10%
    3. 45%
    4. 25% Correct answer.

    Explanation

    Specific yield is the drainable fraction of the pore space, equal to total porosity minus specific retention (the water held by capillary forces). Here 35% minus 10% leaves 25% that will drain under gravity.

  127. Question 127Hydrogeology

    Hydraulic conductivity is expressed in which type of units?

    1. volume per volume
    2. dimensionless
    3. length squared per time
    4. length per time Correct answer.

    Explanation

    In Darcy's law the specific discharge carries units of length per time and the hydraulic gradient is dimensionless, so hydraulic conductivity must also have units of length per time, such as meters per day.

  128. Question 128Hydrogeology

    A saturated geologic unit that can transmit water in quantities large enough to supply a well is called a(n):

    1. aquitard
    2. aquifer Correct answer.
    3. capillary fringe
    4. vadose zone

    Explanation

    An aquifer is a saturated unit that both stores and readily transmits water in usable amounts. Neighboring terms describe units that hold water but transmit it slowly or that lie above the saturated zone.

  129. Question 129Hydrogeology

    The water table of an unconfined aquifer is best defined as the surface at which:

    1. pressure head is negative
    2. pressure head is zero Correct answer.
    3. the top of the capillary fringe lies
    4. total head is zero

    Explanation

    At the water table the pore-water pressure equals atmospheric pressure, so the pressure head is zero and the total head equals the elevation of that surface.

  130. Question 130Hydrogeology

    A confined aquifer is 20 m thick and has a hydraulic conductivity of 10 m/day. Its transmissivity is:

    1. 200 m²/day Correct answer.
    2. 0.5 m²/day
    3. 30 m²/day
    4. 20 m²/day

    Explanation

    Transmissivity is the product of hydraulic conductivity and saturated thickness, T = Kb, so 10 m/day times 20 m gives 200 m²/day.

  131. Question 131Hydrogeology

    Which storativity value is most typical of a confined sand aquifer?

    1. 0.0005 Correct answer.
    2. 0.05
    3. 0.15
    4. 0.25

    Explanation

    Confined storativity reflects only the compressibility of the aquifer skeleton and the water, and typically falls between about 1E-5 and 1E-3. Values of a few percent or more indicate unconfined storage by drainage of pores.

  132. Question 132Hydrogeology

    In a groundwater basin under steady-state conditions with no pumping, average recharge is balanced by:

    1. an increase in effective porosity
    2. upward leakage through the water table
    3. natural discharge from the basin Correct answer.
    4. depletion of aquifer storage

    Explanation

    Steady state means storage does not change with time, so the water-budget equation reduces to inflow equals outflow. Recharge entering the basin must therefore leave as natural discharge to springs, streams, or evapotranspiration.

  133. Question 133Hydrogeology

    In an isotropic aquifer at steady state, groundwater flow is directed toward:

    1. increasing land-surface elevation
    2. increasing hydraulic head
    3. decreasing permeability
    4. decreasing hydraulic head Correct answer.

    Explanation

    Darcy's law states that the specific discharge is proportional to the negative gradient of hydraulic head, so flow moves from higher to lower head regardless of topography.

  134. Question 134Hydrogeology

    A sand has a hydraulic conductivity of 1 m/day, an effective porosity of 0.30, and a hydraulic gradient of 0.01. The average seepage (interstitial) velocity is about:

    1. 0.0003 m/day
    2. 0.30 m/day
    3. 0.01 m/day
    4. 0.033 m/day Correct answer.

    Explanation

    Darcy flux equals K times i, giving 0.01 m/day, and the seepage velocity is that flux divided by effective porosity: 0.01 divided by 0.30 equals about 0.033 m/day.

  135. Question 135Hydrogeology

    After early time, drawdown in an observation well plots as a straight line against the logarithm of time. This response is analyzed with the:

    1. Theis type-curve method
    2. Hantush-Jacob leaky method
    3. Thiem equation
    4. Cooper-Jacob method Correct answer.

    Explanation

    The Cooper-Jacob approximation of the Theis solution shows that when u is small, drawdown becomes linear in log time, and aquifer properties are obtained from the slope and intercept of that straight line.

  136. Question 136Hydrogeology

    Three wells lie on a straight line 1,000 m apart; their water levels are 50 m, 40 m, and 30 m. The hydraulic gradient along that line is:

    1. 0.02
    2. 0.10
    3. 0.01 Correct answer.
    4. 0.20

    Explanation

    Gradient is head change divided by distance: 20 m of head loss over the 2,000 m separating the end wells gives 0.01.

  137. Question 137Hydrogeology

    A well yields 500 gpm at 25 ft of drawdown. Its specific capacity is:

    1. 0.05 gpm/ft
    2. 20 gpm/ft Correct answer.
    3. 25 gpm/ft
    4. 12,500 gpm/ft

    Explanation

    Specific capacity is the pumping rate divided by the resulting drawdown in the same well: 500 gpm divided by 25 ft equals 20 gpm per foot.

  138. Question 138Hydrogeology

    Fresh water in a coastal aquifer stands 1 m above sea level. Using the Ghyben-Herzberg relation, the fresh-salt interface lies about how far below sea level?

    1. 2.5 m
    2. 40 m Correct answer.
    3. 100 m
    4. 10 m

    Explanation

    Because salt water is about 1.025 times as dense as fresh water, the Ghyben-Herzberg relation places the interface roughly 40 times the height of the freshwater head above sea level. One meter of head therefore corresponds to about 40 m of depth.

  139. Question 139Hydrogeology

    An aquifer material has a bulk density of 1.5 g/cm³, a porosity of 0.30, and a distribution coefficient of 0.4 cm³/g. The retardation factor for a sorbing solute is:

    1. 2.0
    2. 1.6
    3. 2.5
    4. 3.0 Correct answer.

    Explanation

    Retardation is R = 1 + (bulk density / porosity) times Kd. Here 1.5 divided by 0.30 gives 5, times 0.4 gives 2, and adding 1 yields a retardation factor of 3.

  140. Question 140Hydrogeology

    Mechanical dispersion of a dissolved plume in a granular aquifer is caused mainly by:

    1. radioactive decay of the solute
    2. molecular diffusion alone
    3. density contrast with native water
    4. pore-scale velocity variations Correct answer.

    Explanation

    Fluid moving through individual pores follows different path lengths and speeds, so the plume spreads beyond the extent predicted by average advection. Diffusion contributes only a small additional spreading at typical groundwater velocities.

  141. Question 141Hydrogeology

    On a stream hydrograph for a basin with no snowmelt, groundwater discharge is represented by:

    1. the total annual runoff volume
    2. the steep rising limb
    3. the storm crest
    4. the slow recession between storms Correct answer.

    Explanation

    Between storms, streamflow is sustained almost entirely by water released from aquifer storage, producing the gradual recession limb of the hydrograph. This baseflow component is the standard field indicator of groundwater discharge.

  142. Question 142Hydrogeology

    A well begins pumping near a gaining stream at a modest rate. The first water captured by the well is:

    1. regional recharge from distant uplands
    2. connate water from the matrix
    3. water previously discharged as baseflow Correct answer.
    4. water drawn directly from the stream

    Explanation

    Capture proceeds in order of increasing resistance: the well first intercepts groundwater that would otherwise have discharged to the stream, and only after that does it induce flow from the stream itself.

  143. Question 143Hydrogeology

    A slug test is used to estimate:

    1. average recharge to the basin
    2. storativity of a confined aquifer
    3. local hydraulic conductivity Correct answer.
    4. regional transmissivity across the basin

    Explanation

    A slug test displaces a small volume of water in a single well and monitors recovery, which reflects only the permeability of a small volume of material immediately around the screened interval.

  144. Question 144Hydrogeology

    In an unconfined aquifer, storativity is approximately equal to:

    1. aquifer compressibility
    2. specific yield Correct answer.
    3. specific retention
    4. total porosity

    Explanation

    When the water table declines, water is released by gravity drainage of pores, so the volume released per unit area per unit head change is the specific yield. The elastic component is negligible by comparison.

  145. Question 145Hydrogeology

    Groundwater contours crossing a gaining stream form a V that points:

    1. away from the stream on both sides
    2. downstream
    3. perpendicular to the stream
    4. upstream Correct answer.

    Explanation

    Contours bend where they cross a stream because the stream is a boundary of constant head. For a gaining stream, groundwater flows toward the channel from both sides, so the contour V points in the upstream direction.

  146. Question 146Hydrogeology

    Drawdown at an observation well follows a semilog straight line and then abruptly flattens to near-constant head at late time. The most likely cause is:

    1. wellbore storage in the pumping well
    2. an impermeable boundary near the well field
    3. a nearby constant-head boundary Correct answer.
    4. a gradual decline in pumping rate

    Explanation

    A constant-head boundary, such as a fully penetrating stream or a recharge front, supplies water that limits further drawdown, so the time-drawdown curve flattens. An impermeable boundary produces the opposite effect, a steepening curve.

  147. Question 147Hydrogeology

    In a mountain-front basin, the stable isotope composition of groundwater is used mainly to estimate:

    1. the aquifer's porosity
    2. the elevation of recharge Correct answer.
    3. the age of the water in years
    4. the aquifer's hydraulic conductivity

    Explanation

    Precipitation becomes progressively depleted in the heavy isotopes oxygen-18 and deuterium as elevation increases, so the isotopic signature of recharge carries an altitude signal. Comparing groundwater to local precipitation establishes the elevation at which recharge entered the subsurface.

  148. Question 148Hydrogeology

    A dense nonaqueous phase liquid is released into an unconfined sandy aquifer. It will most likely:

    1. sink and pool on a low-permeability layer Correct answer.
    2. dissolve completely within a few meters
    3. float on the water table and spread laterally
    4. be retarded more strongly than dissolved chloride

    Explanation

    A dense nonaqueous phase liquid is heavier than water and immiscible with it, so it migrates downward through the unsaturated and saturated zones until it encounters a low-permeability unit, where it accumulates and slowly dissolves.

  149. Question 149Hydrogeology

    In a fractured rock aquifer with dual porosity, the early-time response to pumping is dominated by:

    1. drainage of the matrix blocks
    2. leakage from an overlying confining bed
    3. storage within the well casing
    4. flow in the fracture network Correct answer.

    Explanation

    The fractures provide the high-permeability pathways, so they control the initial drawdown response. Water then bleeds slowly from the low-permeability matrix blocks into the fractures, producing the characteristic late-time flattening of the curve.

  150. Question 150Hydrogeology

    A well pumps 1,000 m³/day from an aquifer with transmissivity 500 m²/day and storativity 0.0005. Using the Theis solution, the drawdown after 1 day at a distance of 100 m is about:

    1. 0.86 m Correct answer.
    2. 0.16 m
    3. 8.6 m
    4. 1.7 m

    Explanation

    The well function argument is u = r²S/(4Tt) = 0.0025, for which the well function is about 5.4. Drawdown is (Q/4πT) times W(u), so 0.16 m multiplied by 5.4 gives about 0.86 m.

  151. Question 151Engineering Geology and Geohazards

    In slope-stability analysis, the factor of safety is defined as the ratio of...

    1. available shear strength to equilibrium shear stress Correct answer.
    2. driving weight to resisting weight
    3. cohesion to internal friction angle
    4. equilibrium shear stress divided by available shear strength

    Explanation

    The factor of safety compares the shear strength available along a potential failure surface with the shear stress required for equilibrium. Values greater than 1 indicate a margin of resistance, while values less than 1 indicate instability.

  152. Question 152Engineering Geology and Geohazards

    Soil liquefaction during an earthquake is best described as...

    1. brittle fracture of cemented gravel along a fault
    2. permanent volume increase caused by compaction of dry sand
    3. strength loss in saturated loose sand as pore pressure rises Correct answer.
    4. slow settlement of clay by secondary consolidation

    Explanation

    Liquefaction occurs when cyclic shaking raises pore-water pressure in saturated loose sand until effective stress and shear strength drop sharply. The soil can then behave like a fluid.

  153. Question 153Engineering Geology and Geohazards

    A fast-moving mixture of water, mud, and rock debris that follows a steep mountain channel is called a...

    1. rock avalanche
    2. rotational slump
    3. soil creep
    4. debris flow Correct answer.

    Explanation

    A debris flow is a gravity-driven, channelized mixture of water and coarse sediment that can move rapidly and travel long distances. Its high sediment concentration distinguishes it from ordinary water floods.

  154. Question 154Engineering Geology and Geohazards

    The principal engineering hazard posed by expansive clay soils is...

    1. volume change with seasonal moisture fluctuation Correct answer.
    2. dissolution and void formation beneath foundations
    3. rapid loss of strength during seismic shaking
    4. corrosion of buried steel utilities

    Explanation

    Expansive clays swell when wetted and shrink when dried, producing differential heave and settlement of foundations and pavements. The damage results from volume change rather than from dissolution or seismic weakening.

  155. Question 155Engineering Geology and Geohazards

    Karst subsidence is most commonly associated with the dissolution of...

    1. granite and welded tuff
    2. limestone and dolomite Correct answer.
    3. shale and mudstone
    4. basalt and andesite

    Explanation

    Karst develops where soluble carbonate rocks such as limestone and dolomite are dissolved by acidic groundwater, producing voids, caves, and sinkholes. Collapse or raveling of soil into these voids can cause surface subsidence.

  156. Question 156Engineering Geology and Geohazards

    Peak ground acceleration (PGA) is used in engineering seismology primarily to characterize...

    1. the duration of strong shaking
    2. the amplitude of ground shaking Correct answer.
    3. the frequency content of shaking
    4. the permanent displacement across a fault

    Explanation

    PGA is the maximum acceleration recorded at a site during an earthquake, so it primarily represents shaking amplitude. Duration and frequency content require additional parameters such as significant duration and response spectra.

  157. Question 157Engineering Geology and Geohazards

    A lahar is a...

    1. fall deposit of pumice and ash
    2. lava flow that advances slowly down a volcano
    3. volcanic mudflow or debris flow Correct answer.
    4. cloud of hot gas and ash that moves laterally

    Explanation

    A lahar is a volcanic mudflow or debris flow formed from water mixed with volcanic ash, rock, and soil. Lahars can travel far from a volcano and are hazardous in valley bottoms and drainage channels.

  158. Question 158Engineering Geology and Geohazards

    Weep holes and a drainage layer behind a retaining wall are installed mainly to...

    1. increase the passive resistance of the soil in front
    2. reduce the wall's self-weight
    3. lower water pressure acting on the wall Correct answer.
    4. prevent frost penetration into the backfill

    Explanation

    Drainage behind a retaining wall removes water and lowers the water table in the backfill, reducing hydrostatic pressure on the wall. Without drainage, water pressure can substantially increase the lateral load.

  159. Question 159Engineering Geology and Geohazards

    A rock slope contains a planar discontinuity that dips 50° out of the slope. The friction angle along the discontinuity is 35° and cohesion is zero. The factor of safety against sliding is approximately...

    1. 0.59 Correct answer.
    2. 1.43
    3. 1.19
    4. 0.84

    Explanation

    For a cohesionless planar discontinuity, the factor of safety is the ratio of available frictional resistance to gravitational driving shear, which simplifies to tan(friction angle) divided by tan(discontinuity dip). Here tan 35° / tan 50° is about 0.59.

  160. Question 160Engineering Geology and Geohazards

    A saturated clay has undrained shear strength 40 kPa and total unit weight 18 kN/m3. Using the vertical-cut relation Hc = 4c/γ, the critical height is approximately...

    1. 17.8 m
    2. 4.4 m
    3. 8.9 m Correct answer.
    4. 2.2 m

    Explanation

    Substituting c = 40 kPa and γ = 18 kN/m3 into Hc = 4c/γ gives 160/18, or about 8.9 m. This relation estimates the maximum stable height of a vertical cut in saturated clay under undrained conditions.

  161. Question 161Engineering Geology and Geohazards

    Which soil profile is most susceptible to liquefaction?

    1. stiff overconsolidated clay
    2. cemented sandstone
    3. dense gravel below the water table
    4. loose saturated fine sand Correct answer.

    Explanation

    Liquefaction is most likely in loose, saturated, clean to silty sands with little cohesion. Dense gravel, stiff clay, and cemented rock tend to have sufficient strength or permeability characteristics to resist liquefaction.

  162. Question 162Engineering Geology and Geohazards

    Compared with a nearby rock site, a thick deposit of soft clay typically causes earthquake shaking to...

    1. have a shorter duration
    2. be reduced in amplitude at all frequencies
    3. shift to higher frequencies
    4. be amplified at low frequencies Correct answer.

    Explanation

    Soft soils have low resonant frequencies and can amplify long-period ground motion, especially where the impedance contrast with bedrock is large. Thick basins can also trap and prolong shaking rather than shorten it.

  163. Question 163Engineering Geology and Geohazards

    The most direct hazard to a building constructed directly across the trace of an active fault is...

    1. regional ground shaking
    2. liquefaction
    3. surface fault rupture Correct answer.
    4. tsunami inundation

    Explanation

    A structure straddling an active fault trace can be torn by differential ground displacement along the rupture. Building codes therefore commonly require setbacks from mapped active fault traces.

  164. Question 164Engineering Geology and Geohazards

    A tsunami is most likely to be generated by...

    1. a hurricane making landfall
    2. a submarine earthquake that lifts the sea floor Correct answer.
    3. a strike-slip earthquake with horizontal motion only
    4. a volcanic ash fall into the ocean

    Explanation

    Tsunamis are generated most efficiently by vertical displacement of the sea floor, which displaces a large volume of ocean water. Strike-slip motion is mainly horizontal and couples poorly with the water column.

  165. Question 165Engineering Geology and Geohazards

    Land subsidence in a heavily pumped alluvial basin is caused mainly by...

    1. lateral erosion by rivers
    2. elastic rebound of bedrock
    3. compaction of aquifer sands as pressure falls Correct answer.
    4. dissolution of evaporite minerals beneath the basin

    Explanation

    Pumping lowers pore pressure in aquifer systems, which increases effective stress and compacts fine-grained sediments. The resulting subsidence is often largely permanent.

  166. Question 166Engineering Geology and Geohazards

    Rock quality designation (RQD) is calculated as the percentage of...

    1. core recovery regardless of piece length
    2. fractures per meter in the core
    3. intact core pieces longer than 10 cm Correct answer.
    4. rock fragments smaller than 10 cm

    Explanation

    RQD is the sum of lengths of intact core pieces at least 10 cm long divided by the total length of the core run, expressed as a percentage. It is a simple index of rock-mass fracturing.

  167. Question 167Engineering Geology and Geohazards

    The Mohr-Coulomb shear-strength criterion for soil is expressed as...

    1. τ = c − σn tan φ
    2. τ = c tan φ + σn
    3. τ = c + σn tan φ Correct answer.
    4. τ = σn / (c + tan φ)

    Explanation

    Mohr-Coulomb strength combines a cohesion intercept with frictional resistance proportional to normal stress. The shear strength therefore increases as normal stress and friction angle increase.

  168. Question 168Engineering Geology and Geohazards

    For a shallow strip footing on sand, increasing the footing width generally...

    1. increases bearing capacity and settlement Correct answer.
    2. has no effect on capacity or settlement
    3. increases bearing capacity only
    4. reduces bearing capacity while reducing settlement

    Explanation

    A wider footing spreads load over a larger area and engages a larger soil wedge, which raises ultimate bearing capacity. However, the stress influence zone extends deeper and wider, so settlement commonly increases as well.

  169. Question 169Engineering Geology and Geohazards

    The most common cause of failure of earth-fill dams is...

    1. concrete deterioration
    2. abrasion of the spillway
    3. foundation uplift
    4. reservoir overtopping Correct answer.

    Explanation

    Overtopping is the leading cause of earth-dam failures because uncontrolled water can rapidly erode the crest and downstream face. Internal erosion and slope instability are also important, but overtopping is historically most common.

  170. Question 170Engineering Geology and Geohazards

    Planar sliding of a rock slope along a single discontinuity is most likely when the discontinuity...

    1. is horizontal across the slope face
    2. dips out of the slope, daylights, and exceeds the friction angle Correct answer.
    3. is filled with cemented gouge along its entire length
    4. dips into the slope at a steep angle

    Explanation

    Planar sliding requires a discontinuity that dips out of the slope and daylights on the face, with a dip angle steep enough to overcome frictional resistance. Release surfaces and water pressure can further promote sliding.

  171. Question 171Engineering Geology and Geohazards

    The Newmark sliding-block method estimates seismic slope performance by calculating...

    1. the slope's resonant frequency
    2. the static factor of safety alone
    3. liquefaction potential at the toe
    4. permanent sliding above yield acceleration Correct answer.

    Explanation

    Newmark analysis treats a potential slide mass as a rigid block that displaces only when earthquake acceleration exceeds the yield acceleration. Integrating the acceleration history above that threshold gives an estimated permanent displacement.

  172. Question 172Engineering Geology and Geohazards

    Lateral spreading during an earthquake typically occurs on...

    1. gently sloping saturated liquefiable sand Correct answer.
    2. steep rock cliffs with little soil cover
    3. massive intact granite
    4. dry dense gravel terraces above the water table

    Explanation

    Lateral spreading occurs where a liquefied subsurface layer loses strength and allows overlying ground to extend laterally toward a free face or down a gentle slope. It commonly affects gently sloping ground and waterfront fills underlain by loose saturated sand.

  173. Question 173Engineering Geology and Geohazards

    A fault has an average slip rate of 2 mm/yr and produces earthquakes with about 1 m of slip. The average recurrence interval is approximately...

    1. 500 years Correct answer.
    2. 2000 years
    3. 200 years
    4. 50 years

    Explanation

    The recurrence interval is the slip per event divided by the slip rate. One meter equals 1000 mm, and 1000 mm divided by 2 mm/yr gives about 500 years.

  174. Question 174Engineering Geology and Geohazards

    A seismic hazard map shows a ground-motion level with a return period of 2,475 years. The approximate annual exceedance probability is...

    1. 40%
    2. 4%
    3. 0.4%
    4. 0.04% Correct answer.

    Explanation

    For a Poisson process, annual exceedance probability is approximately the reciprocal of the return period. One divided by 2,475 is about 0.000404, or 0.04% per year.

  175. Question 175Engineering Geology and Geohazards

    For a dry cohesionless backfill, the Rankine active earth-pressure coefficient Ka is given by...

    1. 1 − tan φ
    2. (1 − sin φ)/(1 + sin φ) Correct answer.
    3. (1 + sin φ)/(1 − sin φ)
    4. tan φ

    Explanation

    The Rankine active coefficient follows from the Mohr circle for a cohesionless soil at failure and decreases as the friction angle increases. The passive coefficient is its reciprocal.

  176. Question 176Economic Geology and Energy Resources

    In a petroleum reservoir, the property that describes the fraction of bulk rock volume available to store fluids is:

    1. Capillary entry pressure
    2. Permeability
    3. Tortuosity
    4. Porosity Correct answer.

    Explanation

    Porosity is the proportion of a rock's bulk volume that is void space, so it directly sets the fluid storage capacity of a reservoir. Permeability instead describes how readily fluids move through the connected pore network.

  177. Question 177Economic Geology and Energy Resources

    Liquid petroleum is generated from organic matter in source rocks chiefly within which temperature range?

    1. 350–450 °C
    2. 60–120 °C Correct answer.
    3. 200–250 °C
    4. 20–40 °C

    Explanation

    The oil window lies at roughly 60–120 °C, corresponding to vitrinite reflectance near 0.6–1.0%. At higher temperatures liquid hydrocarbons are cracked to gas, and at lower temperatures the organic matter remains immature.

  178. Question 178Economic Geology and Energy Resources

    A crude oil with an API gravity of 40° is best described as:

    1. A fluid with the same density as pure water
    2. A heavy oil that will sink in water
    3. A solid bitumen at surface conditions
    4. A light oil less dense than water Correct answer.

    Explanation

    API gravity varies inversely with density, and water is the reference at 10° API. Any oil above about 10° API floats on water, and 40° API indicates a light, low-density crude.

  179. Question 179Economic Geology and Energy Resources

    Which sequence correctly shows coal progressing from lowest to highest rank?

    1. Anthracite → bituminous → sub-bituminous → lignite
    2. Bituminous → lignite → anthracite → sub-bituminous
    3. Lignite → sub-bituminous → bituminous → anthracite Correct answer.
    4. Sub-bituminous → lignite → bituminous → anthracite

    Explanation

    Coal rank increases with burial heating in the order lignite, sub-bituminous, bituminous, and anthracite, accompanied by rising carbon content and vitrinite reflectance and falling volatile matter.

  180. Question 180Economic Geology and Energy Resources

    Banded iron formations, the world's principal source of mined iron, are characteristically:

    1. Precambrian chert–iron oxide layered rocks Correct answer.
    2. Cenozoic bauxite profiles
    3. Mesozoic marine oolitic ironstones
    4. Paleozoic coal-bearing cyclothems

    Explanation

    Banded iron formations are thinly layered chert and iron oxide (hematite and magnetite) successions of Archean to Paleoproterozoic age, deposited before the oceans and atmosphere became widely oxygenated.

  181. Question 181Economic Geology and Energy Resources

    The function of a cap rock in a petroleum accumulation is to:

    1. Prevent upward escape of hydrocarbons Correct answer.
    2. Convert liquid oil into gas
    3. Generate hydrocarbons upon heating
    4. Increase the porosity of the reservoir

    Explanation

    A cap rock is a low-permeability seal whose high capillary entry pressure stops hydrocarbons from migrating out of the top of the reservoir. Common seals include shale, evaporite, and tight carbonate units.

  182. Question 182Economic Geology and Energy Resources

    Hydraulic fracturing is applied in shale gas wells primarily because shale reservoirs have:

    1. Exceptionally high porosity
    2. Very low matrix permeability Correct answer.
    3. High matrix permeability
    4. Thick cap rock above it

    Explanation

    Organic-rich shales store gas in pores and adsorbed on kerogen but have matrix permeabilities in the nanodarcy range, so induced fractures are needed to create conductive flow paths to the wellbore.

  183. Question 183Economic Geology and Energy Resources

    Gold becomes concentrated in stream placers chiefly because gold:

    1. Has high density and chemical resistance Correct answer.
    2. Reacts with quartz to form new minerals
    3. Undergoes rapid dissolution in flowing water
    4. Is less dense than the accompanying sand

    Explanation

    Gold has a specific gravity near 19 and is chemically inert, so it survives weathering and transport while lighter grains are winnowed away, leaving a lag concentrate in gravels.

  184. Question 184Economic Geology and Energy Resources

    Type I kerogen, which yields abundant high-quality oil upon maturation, is derived mainly from:

    1. Terrestrial woody higher-plant material
    2. Lacustrine algal material Correct answer.
    3. Inorganic carbonate mud
    4. Oxidized, reworked humic debris

    Explanation

    Type I kerogen has a high initial hydrogen content and consists largely of algal and amorphous organic matter deposited in lacustrine settings, making it strongly oil-prone.

  185. Question 185Economic Geology and Energy Resources

    A large, low-grade copper–molybdenum deposit centred on a felsic porphyry stock, with concentric potassic, phyllic, and propylitic alteration, is best classified as:

    1. A Mississippi Valley-type deposit
    2. A volcanogenic massive sulfide deposit
    3. A porphyry copper deposit Correct answer.
    4. A sedimentary-exhalative deposit

    Explanation

    Porphyry copper systems are large, low-grade Cu–Mo–Au deposits centred on felsic porphyry intrusions and characterized by zoned hydrothermal alteration from potassic through phyllic to propylitic.

  186. Question 186Economic Geology and Energy Resources

    Volcanogenic massive sulfide (VMS) deposits form chiefly:

    1. By solar evaporation in shallow coastal basins
    2. By contact metamorphism of limestones
    3. At submarine hydrothermal vents on the seafloor Correct answer.
    4. By lateritic weathering of ultramafic rocks

    Explanation

    VMS deposits precipitate as sulfide mounds and stockworks where metal-bearing hydrothermal fluids discharge onto or just below the seafloor, typically at spreading centres where seawater circulates through hot volcanic rock.

  187. Question 187Economic Geology and Energy Resources

    Primary economic diamond deposits are most commonly hosted in:

    1. Kimberlite and lamproite pipes Correct answer.
    2. Sandstone-hosted roll fronts
    3. Carbonate-hosted MVT bodies
    4. Granite pegmatites

    Explanation

    Diamonds are carried to the surface by kimberlitic and lamproitic magmas that rapidly sample the diamond-bearing subcontinental lithospheric mantle, forming pipe-like bodies.

  188. Question 188Economic Geology and Energy Resources

    A nickel laterite deposit forms by:

    1. Intense tropical weathering of ultramafic rock Correct answer.
    2. Precipitation from evaporating brines
    3. Hydrothermal replacement of limestone
    4. Magmatic sulfide segregation in a mafic intrusion

    Explanation

    Lateritic nickel deposits develop where prolonged tropical weathering leaches silica and magnesium from ultramafic rocks and concentrates iron and nickel in residual oxide horizons.

  189. Question 189Economic Geology and Energy Resources

    The high-grade unconformity-related uranium deposits of the Athabasca Basin occur:

    1. At the basement–sandstone unconformity Correct answer.
    2. In evaporite beds within a reef complex
    3. Along the redox boundary in a sandstone aquifer
    4. Within quartz veins in Archean greenstone belts

    Explanation

    These deposits sit at the unconformity between reducing Archean basement rocks and overlying Proterozoic sandstone, where oxidized basinal fluids reacted with basement lithologies to precipitate uraninite.

  190. Question 190Economic Geology and Energy Resources

    Mississippi Valley-type deposits are characteristically:

    1. Bauxite blankets on tropical plateaus
    2. Carbonate-hosted lead–zinc sulfides Correct answer.
    3. Chromite layers in layered mafic intrusions
    4. Copper–gold skarns at intrusive contacts

    Explanation

    MVT deposits are stratabound lead–zinc sulfide bodies in dolostone or limestone, deposited at low temperature (roughly 50–150 °C) from migrating basinal brines far from any igneous heat source.

  191. Question 191Economic Geology and Energy Resources

    A tungsten-bearing garnet–pyroxene assemblage developed where a granitic intrusion cut a limestone is an example of:

    1. A contact-metasomatic skarn Correct answer.
    2. A placer deposit
    3. An evaporite deposit
    4. A sedimentary-exhalative deposit

    Explanation

    Skarns form by contact metasomatism where hot intrusive fluids react with carbonate wall rock, producing calc-silicate minerals such as garnet and pyroxene that may carry tungsten, copper, or zinc.

  192. Question 192Economic Geology and Energy Resources

    Granitic pegmatites are mined chiefly for which group of elements?

    1. Iron, aluminum, and manganese
    2. Lead, zinc, and silver
    3. Lithium, beryllium, and tantalum Correct answer.
    4. Phosphorus, potassium, and nitrogen

    Explanation

    Pegmatites concentrate incompatible elements excluded from common rock-forming minerals, notably lithium, beryllium, tantalum, niobium, cesium, and tin, along with gemstones and industrial feldspar.

  193. Question 193Economic Geology and Energy Resources

    A sandstone reservoir that pinches out updip into impermeable shale, with no folding or faulting involved, is an example of:

    1. A salt-dome trap
    2. An anticlinal trap
    3. A fault trap
    4. A stratigraphic trap Correct answer.

    Explanation

    Stratigraphic traps depend on a change in lithology or reservoir quality, such as an updip pinch-out, diagenetic barrier, or reef buildup, rather than on structural deformation.

  194. Question 194Economic Geology and Energy Resources

    A shale is generally regarded as a possible effective source rock once its total organic carbon content reaches about:

    1. 10 wt%
    2. 0.05 wt%
    3. 0.001 wt%
    4. 0.5 wt% Correct answer.

    Explanation

    Roughly 0.5 wt% TOC is the common minimum threshold for a potential source rock; shales with 2–5 wt% TOC are considered good to excellent.

  195. Question 195Economic Geology and Energy Resources

    In the McKelvey classification, a proved reserve must be:

    1. Identified but currently subeconomic
    2. Any occurrence of the metal, economic or not
    3. Identified, recoverable, and economic Correct answer.
    4. Undiscovered but in a favorable setting

    Explanation

    A reserve is the portion of an identified resource that can be recovered with current technology and is economic at current prices; resources also include undiscovered and subeconomic material.

  196. Question 196Economic Geology and Energy Resources

    Roll-front uranium deposits form where:

    1. Uranium is concentrated by evaporation in a desert basin
    2. Uranium minerals crystallize directly from a cooling granitic magma
    3. Uranium-bearing oxidizing groundwater meets a reducing zone Correct answer.
    4. Uranium substitutes for calcium in reef-building corals

    Explanation

    Oxygenated groundwater carries uranium as soluble U(VI) through a permeable sandstone until it encounters reducing conditions, where U(IV) minerals precipitate in a crescent-shaped front that migrates down-gradient.

  197. Question 197Economic Geology and Energy Resources

    As seawater evaporates progressively in a restricted basin, the minerals precipitate in which order?

    1. Halite → gypsum → calcite → potassium salts
    2. Calcite → gypsum → halite → K salts Correct answer.
    3. Potassium salts → halite → gypsum → calcite
    4. Gypsum → calcite → potassium salts → halite

    Explanation

    Evaporite minerals precipitate in order of increasing solubility as concentration rises: calcite first, then gypsum, then halite, and finally the highly soluble potassium and magnesium salts.

  198. Question 198Economic Geology and Energy Resources

    Coalbed methane production typically begins with a prolonged dewatering stage because:

    1. Methane is generated by thermal cracking during production
    2. Water must be injected to dissolve the coal matrix
    3. Gas is stored as a free phase in large caverns
    4. Adsorbed methane desorbs as pressure is lowered Correct answer.

    Explanation

    Most coalbed methane is adsorbed on micropore surfaces of the coal; pumping water from the cleats lowers reservoir pressure, which allows methane to desorb and flow to the wells.

  199. Question 199Economic Geology and Energy Resources

    Marine gas hydrates are stable where:

    1. Seafloor temperatures above 100 °C
    2. Uniformly hypersaline pore fluids
    3. High temperature and low pressure
    4. Low temperature and moderate-to-high pressure Correct answer.

    Explanation

    Methane clathrates require low temperature and elevated pressure, conditions met in shallow marine sediments and beneath permafrost; the base of the stability zone is fixed by the geothermal gradient.

  200. Question 200Economic Geology and Energy Resources

    A supergene chalcocite blanket forms beneath the oxidized zone of a porphyry copper deposit because:

    1. Rising magmatic fluids deposit sulfides at the surface
    2. Regional metamorphism recrystallizes chalcopyrite
    3. Descending copper-bearing solutions react with sulfides Correct answer.
    4. Meteoric water leaches copper upward to the surface

    Explanation

    Weathering of primary sulfides produces acidic, copper-rich solutions that percolate downward and reprecipitate chalcocite and other secondary sulfides where they encounter reducing, sulfide-bearing rock near the water table.

ASBOG FG PG flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Moho
The Mohorovičić discontinuity is the boundary between Earth's crust and mantle, marked by an abrupt increase in seismic P-wave velocity to about 8 km/s.
Principle of superposition
In an undisturbed sequence of sedimentary rock layers, the oldest layer lies at the bottom and each overlying layer is progressively younger.
Angular unconformity
An erosion surface where tilted or folded strata are truncated and overlain by younger, nearly horizontal layers, indicating deformation followed by erosion and renewed deposition.
Airy isostasy
Model in which topographic loads are supported by variations in crustal thickness, so mountain belts possess deep, low-density roots floating in the denser mantle.
Bowen's reaction series
The ordered sequence in which silicate minerals crystallize from cooling magma, from olivine and calcium plagioclase at high temperature to quartz and potassium feldspar at low temperature.
Mohs hardness scale
A relative scratch-hardness scale from talc (1) to diamond (10); calcite is 3, a fingernail about 2.5, and quartz 7.
Metamorphic facies
A set of mineral assemblages that form under a defined range of pressure and temperature, such as greenschist, amphibolite, blueschist, granulite, and eclogite.
Compatible element
An element with a high partition coefficient that preferentially enters solid minerals rather than melt, so it concentrates in early-formed crystals and is depleted in evolved magma.
Walther's law
The principle that a conformable vertical succession of facies reflects the lateral migration of adjacent depositional environments through time.
Dunham classification
A carbonate classification based on depositional texture: mudstone, wackestone, packstone, grainstone, and boundstone, reflecting mud content and whether grains support the framework.
Graded bedding
A sedimentary structure in which grain size decreases upward within a single bed, typically deposited by a waning current such as a turbidity flow.
Index fossil
A fossil species with a wide geographic range and a short stratigraphic duration, used to correlate and date rock units between regions.
Normal fault
A dip-slip fault in which the hanging wall moves down relative to the footwall, formed by crustal extension and typically dipping about 60 degrees.
Anderson's fault theory
Fault type depends on which principal stress is vertical: normal faults with vertical sigma-1, thrust faults with vertical sigma-3, and strike-slip faults with both horizontal.
Anticline
A fold in which strata arch upward so that the oldest rocks occur in the core, with limbs dipping away from the axial trace.
Thrust fault
A low-angle reverse fault where the hanging wall moves up and over the footwall, accommodating crustal shortening and common in fold-and-thrust belts.
Strahler stream order
A hierarchical numbering of streams in which headwater channels are order 1, and order increases only where two channels of equal order join.
Slope factor of safety
The ratio of shear strength, or resisting forces, to shear stress, or driving forces, along a potential failure surface; values below 1 indicate failure.
Dendritic drainage pattern
A branching, tree-like drainage network developed on relatively uniform, gently dipping terrain where rock resistance and structure exert little channel control.
U-shaped valley
A broad, steep-walled valley with a rounded floor carved by glacial erosion, contrasting with the V-shape typical of fluvial valleys.
Darcy's law
Groundwater discharge equals the product of hydraulic conductivity, cross-sectional area, and hydraulic gradient, written Q = -K A (dh/dL) and valid for laminar flow.
Storativity
The volume of water released from storage per unit surface area of aquifer per unit decline in hydraulic head; equal to specific yield in unconfined aquifers.
Cone of depression
The downward-curved potentiometric surface surrounding a pumping well, caused by drawdown, that expands outward with continued pumping.
Ghyben-Herzberg relation
In coastal aquifers, the freshwater lens extends about 40 times deeper below sea level than the water table stands above sea level, given the density contrast.
Plasticity index
The range of water content between the liquid limit and plastic limit, calculated as PI = LL - PL, indicating a soil's plasticity and clay content.
Effective stress
The intergranular stress carried by the soil skeleton, equal to total stress minus pore water pressure, which controls soil strength and consolidation behavior.
Liquefaction
Loss of shear strength in saturated loose sandy soil when seismic shaking raises pore pressure until effective stress approaches zero, producing flow-like behavior.
Rock quality designation
The percentage of drilled core recovery consisting of intact pieces 10 cm or longer, used together with joint data to rate rock mass quality.
Porphyry deposit
A large, low-grade copper-molybdenum-gold deposit associated with felsic porphyritic intrusions and stockwork veinlets above a magmatic-hydrothermal system.
Oil window
The temperature interval of roughly 60 to 120 degrees Celsius in which kerogen in source rock matures into liquid petroleum before cracking to gas.
Coal rank
The degree of coalification from peat through lignite, subbituminous, bituminous, and anthracite, reflecting increasing carbon content, heat, and pressure.
Reserve versus resource
A resource is a concentration of material that may be economically extracted; a reserve is the portion demonstrated to be profitable under current conditions.

ASBOG FG PG study guide

General Geology and Earth Materials

What to know

The Earth is described two ways: compositionally (crust, mantle, core) and mechanically (lithosphere, asthenosphere, mesosphere, outer core, inner core). The Mohorovičić discontinuity is the crust–mantle boundary, but the lithosphere–asthenosphere boundary is a strength/creep transition that generally lies within the mantle. Plate tectonics unifies seismicity, volcanism, and topography: divergent boundaries give normal faulting and new crust, convergent boundaries give thrust/reverse faulting and subduction, transform boundaries give strike-slip faulting. Isostasy (Airy and Pratt models) explains why thick, low-density crust stands high.

Relative dating rests on superposition, original horizontality, lateral continuity, cross-cutting relationships, inclusions, and faunal succession. Absolute dating rests on radioactive decay, where the fraction of parent remaining is f = (1/2)^n with n = number of half-lives elapsed.

Traps

Equating lithosphere with crust; assuming the asthenosphere is molten (it is solid but weak); mixing half-lives among isotopic systems (14C ≈ 5,730 yr; 40K ≈ 1.25 Ga; 238U ≈ 4.47 Ga; 87Rb ≈ 48.8 Ga); confusing rank of era/period/epoch; treating a mineral date as a rock-formation age without considering closure temperature.

Rule of thumb

Count half-lives from the surviving parent fraction, not from the daughter. If 12.5% parent remains, that is 1/2, 1/4, 1/8 - three half-lives. A granite with 1/8 of its 40K remaining is about 3.75 Ga old only if the system stayed closed.

Mineralogy, Petrology, and Geochemistry

What to know

Mineral identification uses crystal system, cleavage, hardness, specific gravity, luster, and optical properties. Silicate structures run from isolated tetrahedra (olivine) through single and double chains (pyroxene, amphibole) to sheets (micas, clays) and frameworks (quartz, feldspars); this progression tracks rising Si:O and generally lower density, and controls cleavage (micas = one perfect sheet cleavage; pyroxene = two at ~90°; amphibole = two at ~60°/120°).

Igneous rocks are classified by texture (cooling history) and composition; the IUGS QAPF scheme plots modal quartz, alkali feldspar, and plagioclase. Bowen's reaction series describes crystallization order and, reversed, partial melting: mantle peridotite melts to basalt, and fractional crystallization drives residual liquids toward andesite and rhyolite while Mg, Fe, Ca, and Ni fall and Si, K, and Na rise. Metamorphic rocks are classified by facies - mineral assemblages recording temperature and pressure - not by texture alone.

Geochemistry separates compatible elements (Ni, Cr, Mg) from incompatible elements (Rb, Ba, U, Th, Nb) using partition coefficients. Radiogenic isotopes trace source and age; stable isotopes (O, H, C, S) trace processes such as temperature, fluid source, and evaporation.

Traps

Confusing polymorphs (quartz/coesite/stishovite; calcite/aragonite; kyanite/sillimanite/andalusite); calling a glassy rock a mineralogic class; assuming high-grade metamorphism always means high pressure; mistaking a cumulate for a fractionated liquid composition.

Rule of thumb

Quartz + K-feldspar + muscovite = felsic; olivine + pyroxene with little feldspar = ultramafic. Use mineral assemblage first, texture second.

Sedimentology, Stratigraphy, and Paleontology

What to know

Siliciclastic sediment is described by grain size (Wentworth scale), sorting, roundness, and maturity. Transport mode (traction, saltation, suspension) leaves structures: cross-bedding, ripples, horizontal lamination, graded bedding, mudcracks, and bioturbation. Carbonates are classified by grain type and texture (Dunham: mudstone, wackestone, packstone, grainstone, boundstone).

Stratigraphy has parallel frameworks: lithostratigraphy (rock units), biostratigraphy (fossil zones), chronostratigraphy (time), magnetostratigraphy, and sequence stratigraphy (systems tracts bounded by unconformities and flooding surfaces). Unconformities are angular, disconformity, or nonconformity. Walther's Law states that vertical facies successions record laterally adjacent environments, provided the contact is conformable. Transgressions produce fining-upward, deepening successions; regressions produce coarsening-upward, shoaling successions.

Paleontology emphasizes index fossils (wide geographic range, short time range), biozones, and preservation mode (permineralization, molds/casts, carbonization, trace fossils).

Traps

Reading cross-bed foresets as dipping upcurrent (they dip downcurrent); confusing fining-upward with regression; assuming every fossil is a good index fossil; calling a disconformity an angular unconformity without evidence of tilted beds below; treating a biozone as an exactly isochronous surface.

Rule of thumb

Look at the base of the bed: rip-up clasts, sole marks, and coarse sand fining upward into mud = turbidite (Bouma sequence, deepening then abandonment), not a beach.

Worked example: a sandstone with tabular cross-beds dipping southwest and a southwest-thinning wedge indicates paleoflow to the southwest - use the dip direction of foresets, not the set boundaries.

Structural Geology and Tectonics

What to know

Stress is a tensor; the principal stresses are ordered σ1 ≥ σ2 ≥ σ3. Normal faults form with vertical σ1, reverse/thrust faults with horizontal σ1, and strike-slip faults with vertical σ2. The Mohr circle, with a Coulomb failure envelope (τ = c + σn tanφ), shows how pore pressure shifts the circle left and promotes failure. Strain may be brittle (faults, joints) or ductile (folds, foliation, shear zones).

Fold terminology: anticline/syncline (younging direction), hinge line, limbs, axial surface, and plunge. Plunging folds produce V-shaped map outcrop patterns that point in the plunge direction. Faults are described by dip, hanging wall, footwall, and slip sense (normal, reverse, dextral, sinistral). Stereographic projections solve orientation problems; focal mechanisms give earthquake slip sense.

Plate tectonics provides the framework: ridges (extension), trenches and arcs (subduction), and transform faults (shear). Orogens stack thrust sheets and thicken crust, producing regional metamorphism.

Traps

Deriving fault type from map offset rather than from the stress regime and dip; confusing apparent dip with true dip; forgetting that strike-slip faults on a map show offset of markers but little topographic scarp; confusing plunge direction with dip direction; mistaking a monocline for a fault.

Rule of thumb

tan(apparent dip) = tan(true dip) × sin(angle between strike and the section line). If a section is perpendicular to strike, apparent dip = true dip.

Worked example: true dip 30° to the east, section line trending 45° from strike → tanδ' = tan30° × sin45° = 0.577 × 0.707 = 0.408, so apparent dip ≈ 22°.

Geomorphology and Surficial Processes

What to know

Landscapes reflect weathering (physical, chemical, biological), erosion, transport, and deposition acting on uplifted rock. Mass wasting is classified by material (rock, debris, earth) and movement (fall, slide, flow, creep); slope stability is limited by a threshold angle set by friction and pore pressure. Fluvial systems follow discharge Q = w·d·v, with channel form adjusting to sediment load and bank material; sinuosity = channel length ÷ valley length. Base-level change propagates incision or aggradation upstream.

Glacial systems produce U-shaped valleys, striations, till, moraines, drumlins, eskers, and outwash. Coasts respond to wave refraction, longshore drift, and sediment supply. Karst develops where soluble rock permits focused groundwater flow, producing sinkholes, sinking streams, and caves. Drainage patterns record structure: dendritic (uniform), trellis (folded), radial (domes), rectangular (jointed).

Two end-member views: Davis's cyclic peneplanation versus dynamic equilibrium, where form adjusts continuously to process and rock resistance.

Traps

Equating weathering with erosion (weathering produces regolith in place); calling a U-shaped valley fluvial; assuming a stream's velocity depends only on gradient (discharge and roughness matter); forgetting that sinuosity > 1.5 defines meandering; treating alluvial fans and deltas as the same feature.

Rule of thumb

Stream competence scales roughly with v²; capacity with Q and slope. Doubling width or depth doubles Q; doubling velocity quadruples the size of sediment that can be moved.

Worked example: a 20 m wide, 2 m deep channel with mean velocity 1.5 m/s carries Q = 20 × 2 × 1.5 = 60 m³/s.

Hydrogeology

What to know

Porosity is storage; permeability (hydraulic conductivity, K) is the ability to transmit water. An unconfined aquifer is bounded by a water table; a confined aquifer's potentiometric surface may lie above the top of the unit. Aquitards retard flow but do not stop it.

Darcy's law: Q = K·i·A, where i is the hydraulic gradient (dimensionless). Transmissivity T = K·b (units of m²/day) describes the whole saturated thickness b. Storativity S is dimensionless: for confined aquifers it is small (roughly 10⁻⁵ to 10⁻³, from compressibility), while for unconfined aquifers it approximates specific yield (0.1–0.3). Specific retention is water held against gravity.

Well hydraulics: pumping creates a cone of depression; drawdown versus time is analyzed with Theis or Cooper–Jacob methods; boundary conditions (recharge, faults) bend the curves. Water-quality work uses advection–dispersion, sorption retardation (R = 1 + ρbKd/θ), and decay. Coastal aquifers follow the Ghyben–Herzberg relation.

Traps

Mixing K and T; assigning large storativity to a confined aquifer; using water-table elevation as head in a confined system; confusing porosity with permeability (clay is porous but nearly impermeable); forgetting that the gradient is measured between head measurements, not along the pipe.

Rule of thumb

Ghyben–Herzberg: freshwater lens thickness ≈ 40 × water-table height above sea level (for fresh 1.000 and seawater 1.025 g/cm³).

Worked example: K = 10 m/day, i = 0.001, A = 100 m² → Q = 10 × 0.001 × 100 = 1 m³/day.

Engineering Geology and Geohazards

What to know

Index testing begins with grain size, Atterberg limits, and plasticity index (PI = LL − PL). The Unified Soil Classification System groups soils by grain size and plasticity, which informs compaction, compressibility, and strength. Compaction tests (Standard and Modified Proctor) define maximum dry density at optimum water content. Consolidation analysis uses compression index Cc, coefficient of consolidation cv, and preconsolidation pressure to predict settlement.

Shear strength follows Mohr–Coulomb: τ = c′ + σ′n tanφ′, in terms of effective stress. Undrained conditions (φu ≈ 0) are used for short-term loading of saturated clays; drained parameters apply long-term. Effective stress σ′ = σ − u controls volume change and strength.

Slope stability compares resisting to driving forces: FS = resisting/driving; FS < 1 indicates failure. Common failure surfaces include planar (infinite slope), circular (rotational slump), and wedge (rock). Rock mass characterization uses RQD, discontinuities, RMR, and Q. Geohazards include liquefaction of loose saturated sands, seismically induced settlement, rockfall, debris flows, and karst subsidence.

Traps

Using total instead of effective stress; applying drained parameters to rapid loading of saturated clay; confusing PI with liquidity index; assuming high porosity means high strength; using FS < 1.5 as acceptable for permanent slopes in practice (often 1.3–1.5 minimum).

Rule of thumb

Infinite slope with seepage parallel to the surface: FS = [c′ + (γ − γw) z cos²β tanφ′] / (γ z sinβ cosβ). At c′ = 0, FS = [(γ − γw)/γ]·(tanφ′/tanβ), so β must be below φ′ for stability.

Economic Geology and Energy Resources

What to know

Ore deposits are grouped by process: magmatic segregation (chromite, Ni–Cu, PGE), porphyry Cu–Mo–Au, skarn, volcanogenic massive sulfide, SEDEX, Mississippi Valley-type Pb–Zn, epithermal Au–Ag, orogenic gold, banded iron formation, laterite (Ni, bauxite), carbonatite REE, pegmatite (Li, Ta, Be), and placer deposits. A genetic model requires a source, a transporting fluid (chloride and bisulfide complexes carry metals), and a trap (boiling, cooling, mixing, pH change, reduction).

Resource classification matters: a resource is a concentration with reasonable prospects; a reserve is the economically recoverable part, demonstrated by technical study. Contained metal = tonnage × grade.

The petroleum system has six elements: source rock (organic richness, kerogen type, thermal maturity), migration, reservoir (porosity plus permeability), seal, trap, and timing. The oil window is roughly 60–120 °C (vitrinite reflectance ~0.6–1.3%), with gas at higher maturity. Coal rank runs peat → lignite → sub-bituminous → bituminous → anthracite, measured by vitrinite reflectance and volatile matter. Unconventional resources include shale oil/gas, tight gas, coalbed methane, and gas hydrates.

Traps

Confusing reserves with resources; equating coal rank with geologic age; assuming porosity guarantees production (permeability matters); forgetting the seal or timing element in a petroleum play; confusing grade units (%, g/t, ppm).

Rule of thumb

1% Cu over 10 million tonnes = 100,000 t contained copper. Always multiply before comparing deposits.

ASBOG FG PG cheat sheet

Quick reference

General Geology and Earth Materials

  • Earth's layered structure: felsic continental crust (~35 km), mafic oceanic crust (~7 km), mantle to 2900 km depth, liquid outer core, and solid inner core.

  • Major seismic discontinuities: Moho (crust–mantle), Gutenberg (mantle–core at ~2900 km), and Lehmann (inner-core boundary).

  • Relative dating principles: superposition, original horizontality, lateral continuity, cross-cutting relationships, inclusions, and faunal succession.

  • Unconformity types: angular (truncated tilted beds), disconformity (erosion surface between parallel beds), and nonconformity (sedimentary rocks over igneous or metamorphic basement).

  • Airy isostasy supports topography by variations in crustal thickness (mountains have deep roots); Pratt isostasy supports it by lateral density contrasts at a constant compensation depth.

  • Geologic time hierarchy: eon, era, period, epoch; Phanerozoic eras are Paleozoic, Mesozoic, and Cenozoic.

  • Plate boundaries: divergent (new crust, normal faults), convergent (subduction or collision, thrusts), and transform (strike-slip).

  • Radiometric dating depends on closure temperature; U-Pb in zircon is the most robust method for old rocks, while 14C is limited to about 50 ka.

  • Seafloor magnetic anomalies record geomagnetic field reversals and provide the primary evidence for seafloor-spreading rates.

Quick reference

Mineralogy, Petrology, and Geochemistry

  • Bowen's reaction series: olivine → pyroxene → amphibole → biotite (discontinuous branch) and Ca-plagioclase → Na-plagioclase (continuous branch); quartz and K-feldspar crystallize last.

  • Silicate structural classes: nesosilicate (olivine), sorosilicate, cyclosilicate, single-chain inosilicate (pyroxene), double-chain inosilicate (amphibole), phyllosilicate (mica, clay), and tectosilicate (quartz, feldspar).

  • Mohs hardness: 1 talc, 2 gypsum, 3 calcite, 4 fluorite, 5 apatite, 6 orthoclase, 7 quartz, 8 topaz, 9 corundum, 10 diamond.

  • Igneous classification by SiO2: felsic >63%, intermediate 52–63%, mafic 45–52%, ultramafic <45%; plutonic versus volcanic texture reflects cooling rate.

  • Metamorphic facies series: low P/T gives greenschist–amphibolite–granulite; high P/T gives blueschist–eclogite; index minerals include chlorite, biotite, garnet, staurolite, kyanite, and sillimanite.

  • Goldschmidt element classes: lithophile, siderophile, chalcophile, atmophile; compatible elements (Ni, Cr) enter early solids, incompatible elements (Rb, Ba, U, Th, Nb) concentrate in melts.

  • Radioactive decay: N = N0 e^(−λt) with λ = ln2 / half-life; isochron methods use multiple isotopic ratios to solve for age and initial ratio simultaneously.

  • Gibbs phase rule F = C − P + 2; eutectic and peritectic relations plus fractional crystallization control melt paths and enrich residual liquids in silica and incompatible elements.

Quick reference

Sedimentology, Stratigraphy, and Paleontology

  • Wentworth scale: clay <1/256 mm, silt 1/256–1/16 mm, sand 1/16–2 mm, and gravel (granule, pebble, cobble, boulder) >2 mm.

  • Textural maturity increases with better sorting, greater roundness, and removal of clay matrix; quartz arenite is the most mature sandstone.

  • Dunham carbonate classification: mudstone, wackestone, packstone, grainstone, and boundstone; Folk classification uses allochem type and orthochem matrix.

  • Diagnostic sedimentary structures: cross-bedding (flow direction), graded bedding (waning currents), ripples, mudcracks (subaerial exposure), and bioturbation.

  • Walther's law: conformable vertical facies successions record laterally adjacent environments; fining-upward successions commonly record transgression.

  • Sequence stratigraphic systems tracts: lowstand, transgressive, highstand, and falling stage, bounded by sequence boundaries and maximum flooding surfaces.

  • Index fossils: trilobites (Paleozoic), ammonites (Mesozoic), graptolites (Ordovician–Silurian), conodonts, and planktonic foraminifera and nannofossils (Cretaceous–Cenozoic).

  • Stratigraphic codes recognize lithostratigraphic, biostratigraphic, chronostratigraphic, and magnetostratigraphic units, each governed by separate naming rules.

Quick reference

Structural Geology and Tectonics

  • Orientation conventions: strike is the compass trend of a horizontal line on a plane; dip is the steepest inclination perpendicular to strike; apparent dip is always less than or equal to true dip.

  • Fold elements: limb, hinge line, axial surface, plunge, and vergence; anticlines contain the oldest rocks in the core, synclines the youngest.

  • Anderson's theory: normal faults form with vertical σ1, thrust faults with vertical σ3, and strike-slip faults with σ1 and σ3 horizontal and σ2 vertical.

  • Hanging wall moves down in normal faults (extension) and up in reverse faults (shortening); thrusts are reverse faults dipping less than about 45°.

  • Mohr–Coulomb failure: τ = c + σn tan φ; Byerlee's law gives friction coefficients of roughly 0.6–0.85 for most rocks at depth.

  • Shear-sense indicators include S-C fabrics, rotated porphyroclasts, asymmetric folds, and sigmoidal vein arrays; all indicators in one outcrop must agree.

  • Thrust-belt geometry: ramp-flat staircase trajectories, fault-bend and fault-propagation folds, duplexes, and hinterland-dipping versus foreland-dipping panels.

  • Strain is described by stretch and shear: pure shear (flattening) versus simple shear (rotation), with finite strain ellipsoid axes X ≥ Y ≥ Z.

Quick reference

Geomorphology and Surficial Processes

  • Weathering: hydrolysis of feldspars to clays, oxidation of iron-bearing minerals, and carbonate dissolution; physical processes include freeze-thaw, salt wedging, and unloading exfoliation.

  • Mass wasting classes: fall, topple, slide (rotational or translational), flow (debris flow, earthflow), and creep; triggers include water, seismic shaking, and toe undercutting.

  • Drainage patterns: dendritic (uniform substrate), trellis (folded strata), radial (domes and volcanoes), rectangular (jointed rock), and deranged (glaciated terrain).

  • Strahler ordering: order 1 at headwaters; order increases only where two channels of equal order join; drainage density equals channel length divided by basin area.

  • Graded streams have concave-up longitudinal profiles controlled by base level; knickpoints mark disequilibrium and migrate upstream.

  • Glacial landforms: erosional features include cirques, arêtes, horns, U-shaped valleys, and roches moutonnées; depositional features include till, moraines, drumlins, eskers, and outwash.

  • Eolian features: barchan dunes (limited sand, unidirectional wind), transverse ridges, longitudinal seifs, and star dunes; loess is wind-blown silt.

  • Karst features include sinkholes, caves, disappearing streams, and large springs formed by carbonate dissolution along joints; karst aquifers transmit water rapidly with little filtration.

  • Soil profile horizons: O (organic), A (topsoil), E (eluviation), B (accumulation), C (weathered parent material), and R (bedrock).

Quick reference

Hydrogeology

  • Darcy's law: Q = −K A (dh/dL); specific discharge q = Q/A = −K i, valid for laminar flow; transmissivity T = K b.

  • Porosity distinctions: total versus effective porosity; specific yield is drainable porosity and specific retention is water held against gravity; confined storativity ranges roughly 1e-5 to 1e-3.

  • Hydraulic head h = z + P/(ρg); groundwater flows from high to low head; the potentiometric surface represents confined-aquifer head and the water table represents unconfined head.

  • Aquifer tests: Theis solution uses the exponential integral; Cooper–Jacob straight-line applies when u < 0.01; leaky aquifers follow Hantush type curves.

  • Pumping produces a cone of depression; well interference reduces yield; specific capacity Q/s is a practical index of transmissivity.

  • Groundwater budget: recharge = discharge + change in storage; baseflow sustains streams between storms and is estimated from hydrograph separation.

  • Contaminant transport: advection velocity v = q/n_e, mechanical dispersion and diffusion, sorption with retardation factor R = 1 + (ρb/n) Kd, and first-order decay.

  • Ghyben–Herzberg relation: freshwater-saltwater interface depth below sea level is about 40 times the water-table elevation above sea level; overpumping causes saltwater intrusion.

Quick reference

Engineering Geology and Geohazards

  • Atterberg limits: liquid limit, plastic limit, and shrinkage limit; plasticity index PI = LL − PL; liquidity index = (w − PL)/PI.

  • Effective stress σ' = σ − u controls strength and consolidation; Terzaghi 1-D consolidation theory gives settlement; OCR = preconsolidation stress / current effective stress.

  • Mohr–Coulomb strength: τ = c' + σ' tan φ'; drained and undrained (φ = 0, cu) parameters must match the drainage conditions expected in the field.

  • Slope stability factor of safety FS = resisting shear strength / driving shear stress; for an infinite slope FS = [c' + (γ − mγw) z cos²β tan φ'] / (γ z sinβ cosβ).

  • Rock mass classification: RQD (percentage of core in intact pieces >10 cm), RMR (RQD, UCS, spacing, joint condition, water), and Q-system (RQD/Jn × Jr/Ja × Jw/SRF).

  • Landslide triggers include rainfall infiltration, rapid drawdown, seismic shaking, toe erosion, and loading; warning signs include tension cracks, bulging, and tilting trees.

  • Earthquake size: moment magnitude Mw = (2/3) log10 M0 − 6.07 with M0 in N·m; Modified Mercalli intensity describes observed shaking effects.

  • Liquefaction susceptibility is highest in loose, saturated, well-sorted sands and silts with a shallow water table and strong shaking; mitigation includes densification and drainage.

Quick reference

Economic Geology and Energy Resources

  • Magmatic ore deposits: layered mafic intrusions (Cr, PGE), magmatic sulfide Ni-Cu, carbonatites (REE, Nb), and kimberlites (diamond).

  • Hydrothermal deposit types: porphyry Cu-Mo-Au, epithermal Au-Ag, volcanogenic massive sulfide Cu-Zn, SEDEX Pb-Zn, Mississippi Valley-type Zn-Pb, skarn W-Cu, and orogenic Au.

  • Ore deposition mechanisms: cooling, boiling, fluid mixing, pH change, and wall-rock reaction; boiling is especially effective for gold precipitation.

  • Sedimentary and surficial deposits: banded iron formation, phosphorite, evaporites (potash, gypsum, halite), placer gold and heavy minerals, and roll-front uranium.

  • Coal rank series: peat → lignite → subbituminous → bituminous → anthracite, tracking increases in vitrinite reflectance, carbon content, and calorific value.

  • Petroleum system elements: source rock (kerogen types I–IV), maturation (oil window roughly 60–120 °C), migration, reservoir with porosity and permeability, seal, and trap.

  • Trap types: structural (anticline, fault block) and stratigraphic (pinch-out, reef, unconformity); API gravity classifies light (<35°) and heavy (>20°) oils.

  • Resource classification: resources include undiscovered and subeconomic material; reserves are discovered, economically recoverable under current prices and technology and are defined by a cut-off grade.

ASBOG FG PG key terms

Mohs hardness scale

A ranking of ten reference minerals from talc (1) to diamond (10) that expresses resistance to scratching; geologists use it to estimate the relative hardness of an unknown mineral specimen in the field.

Related: Mineral cleavage
Mineral cleavage

The tendency of a mineral to break along specific planes of weak atomic bonding, producing flat, reflective surfaces; the number of planes and the angles between them are key identification criteria.

Related: Mohs hardness scale
Isostasy

The condition in which the lithosphere floats in gravitational balance on the denser asthenosphere, so thick or low-density crust stands higher than thin or dense crust, and loads are compensated at depth.

Bowen's reaction series

An ordered sequence describing the temperatures at which common silicate minerals crystallize from cooling magma, from olivine and calcium-rich plagioclase first to quartz and potassium feldspar last.

Related: Fractional crystallization, Partial melting
Partial melting

Incomplete melting of rock, usually at depth, that produces a silica-rich liquid and leaves a refractory solid residue behind; it is the dominant process that generates magma in the crust and mantle.

Related: Bowen's reaction series, Fractional crystallization
Fractional crystallization

Separation of early-formed crystals from a cooling magma, which shifts the remaining liquid toward more silica-rich compositions; it is a principal cause of magmatic differentiation within an intrusion.

Related: Bowen's reaction series, Partition coefficient
Geothermal gradient

The rate at which temperature rises with depth in the Earth, commonly about 20 to 30 degrees Celsius per kilometer in continental crust; it governs metamorphic grade and the depth of hydrocarbon generation.

Related: Oil window, Foliation
Partition coefficient

The ratio of an element's concentration in a mineral to its concentration in the coexisting melt or fluid; it determines whether an element behaves compatibly or incompatibly during melting and crystallization.

Related: Partial melting, Fractional crystallization
Foliation

A planar fabric in metamorphic rock produced by aligned platy minerals, compositional layering, or preferred crystal orientation; it develops perpendicular to the direction of maximum compressive stress.

Related: Geothermal gradient
Walther's Law

The principle that a vertical succession of sedimentary facies records the lateral migration of neighboring depositional environments, so facies found side by side can also stack one above another.

Related: Facies, Unconformity
Facies

A body of sedimentary rock distinguished by its lithology, sedimentary structures, and fossil content, reflecting a particular depositional environment or a restricted set of environmental conditions.

Related: Walther's Law, Cross-bedding
Unconformity

A surface marking a gap in the rock record where erosion or non-deposition removed time; angular unconformities, disconformities, and nonconformities are the recognized varieties.

Related: Facies, Index fossil
Index fossil

A fossil species with a short stratigraphic range and broad geographic distribution, used to correlate rock units between regions and to assign relative ages.

Related: Unconformity, Facies
Diagenesis

The low-temperature physical, chemical, and biological changes that alter sediment after deposition and before metamorphism, including compaction, cementation, dissolution, and recrystallization.

Related: Porosity, Facies
Cross-bedding

Inclined layers nested within a sedimentary bed, formed as ripples or dunes migrate; the dip direction of the foreset layers indicates the trend of the ancient current or wind.

Related: Facies, Walther's Law
Strike and dip

Two measurements that define the orientation of a planar geologic feature: strike is the compass direction of the horizontal line on the plane, and dip is the angle of steepest descent.

Related: Hanging wall, Anticline
Hanging wall

The rock mass lying above a dipping fault surface; its relative movement distinguishes normal faults, where it drops, from reverse faults, where it rises.

Related: Strike and dip, Décollement
Anticline

A fold whose two limbs dip away from a central axis, with the oldest exposed rocks in the core; it commonly forms a structural trap that concentrates oil and gas.

Related: Strike and dip, Reservoir rock
Elastic rebound

The earthquake mechanism in which strain accumulates elastically in rock across a locked fault and is suddenly released as slip, radiating seismic waves.

Related: Hanging wall
Décollement

A low-angle or nearly horizontal detachment fault along which an upper rock mass slides over a footwall, typically lubricated by a weak layer such as salt or shale.

Related: Hanging wall, Strike and dip
Base level

The lowest elevation to which a stream can erode, ultimately sea level but locally a lake, reservoir, or resistant ledge; a change in base level drives incision or deposition along the channel.

Related: Karst
Angle of repose

The steepest slope angle at which loose granular material stays stable, typically about 30 to 35 degrees for dry sand; it controls the profile of talus slopes and dunes.

Related: Factor of safety, Liquefaction
Karst

A landscape developed by dissolution of soluble rock such as limestone or gypsum, characterized by sinkholes, caves, disappearing streams, and poorly developed surface drainage.

Related: Porosity, Base level
Porosity

The fraction of a rock or sediment volume that consists of void space; it controls how much water, oil, or gas a material can store.

Related: Hydraulic conductivity, Specific yield, Reservoir rock
Hydraulic conductivity

A measure of how readily a fluid moves through a porous medium under a given hydraulic gradient, reflecting both the permeability of the medium and the density and viscosity of the fluid.

Related: Porosity, Potentiometric surface, Cone of depression
Specific yield

The volume of water that drains by gravity from a unit volume of saturated aquifer material; it approximates the effective porosity available to pumping wells in unconfined aquifers.

Related: Porosity, Hydraulic conductivity
Potentiometric surface

An imaginary surface representing the height to which water would rise in a well completed in a confined aquifer; it expresses hydraulic head and the direction of groundwater flow.

Related: Cone of depression, Hydraulic conductivity
Cone of depression

A roughly conical downward distortion of the water table or potentiometric surface around a pumping well, created by withdrawal and shaped by aquifer properties and pumping rate.

Related: Potentiometric surface, Specific yield
Atterberg limits

Water-content thresholds, including the liquid, plastic, and shrinkage limits, that define the consistency states of fine-grained soil and are used to classify soils and predict engineering behavior.

Related: Liquefaction, Factor of safety
Liquefaction

Loss of shear strength in saturated loose sandy soil when earthquake shaking raises pore-water pressure until the material temporarily behaves as a fluid, causing settlement and foundation failure.

Related: Atterberg limits, Factor of safety
Factor of safety

The ratio of resisting forces or available strength to driving forces or applied stress on a slope, foundation, or structure; values near one indicate marginal stability.

Related: Angle of repose, Liquefaction
Rock quality designation

A measure of rock mass quality calculated as the percentage of drill core recovered in intact pieces longer than 10 centimeters, widely used in rock mass classification for foundations and tunnels.

Related: Factor of safety, Atterberg limits
Cut-off grade

The minimum concentration of a commodity in rock that makes mining a block economic; it separates ore from waste and depends on metal prices, operating costs, and recovery.

Source rock

A fine-grained, organic-rich sedimentary rock, typically shale or limestone, that generated hydrocarbons when buried and heated to maturity.

Related: Oil window, Reservoir rock
Reservoir rock

A porous and permeable rock, such as sandstone or fractured limestone, that stores and transmits oil, gas, or water in quantities that can be produced economically.

Related: Source rock, Porosity, Anticline
Oil window

The temperature interval, roughly 60 to 150 degrees Celsius or about 2 to 4 kilometers depth, in which kerogen in source rock matures into liquid hydrocarbons; hotter conditions yield gas.

Related: Source rock, Geothermal gradient

ASBOG FG PG study plan

8 weeks · About 7 hours per week

Week 1

General Geology and Earth Materials & Mineralogy, Petrology, and Geochemistry

  • Classify 40 common rock-forming minerals using hand-sample diagnostic properties (cleavage, hardness, luster, streak, crystal form)

  • Apply Bowen's reaction series to predict mineral assemblages and crystallization order across felsic-to-mafic compositions

  • Distinguish igneous, sedimentary, and metamorphic rock types from texture-and-composition descriptions and assign each to a plausible tectonic setting

  • Use metamorphic facies and index-mineral assemblages to estimate pressure-temperature conditions of formation

Your checkpoint

A one-page condensed reference sheet covering 40 minerals and 15 rock types, plus a 20-question self-quiz scored at 80% or higher with every miss written into an error log

Week 2

Mineralogy, Petrology, and Geochemistry & Sedimentology, Stratigraphy, and Paleontology

  • Interpret grain size, sorting, and rounding to infer sediment transport distance and depositional energy

  • Apply Walther's Law and standard facies models to reconstruct vertical successions from written bed-by-bed descriptions

  • Identify common index fossils and biozones and use them to assign relative ages

  • Correlate two stratigraphic sections using lithostratigraphic markers, key beds, and sequence-stratigraphic surfaces

Your checkpoint

Two hand-drawn stratigraphic columns built from written descriptions and correctly correlated, accompanied by a written justification and a 25-question timed quiz scored at 88% or higher

Week 3

Sedimentology, Stratigraphy, and Paleontology & Structural Geology and Tectonics

  • Determine strike and dip from map data by solving three-point problems

  • Classify folds and faults from map patterns and cross-section geometry, and infer the causative stress regime

  • Apply superposition, cross-cutting relations, and inclusion principles to order deformation and depositional events

  • Distinguish unconformity types and explain what each implies about the missing record

Your checkpoint

Three completed cross-sections through folded and faulted terranes constructed from written attitude data, each with a labeled, ordered geological history

Week 4

Structural Geology and Tectonics & General Geology and Earth Materials

  • Plot planes and lineations on a stereonet and interpret fold axes and fault-plane solutions

  • Relate divergent, convergent, and transform boundaries to characteristic structural styles and seismicity patterns

  • Synthesize Domains 1-4 by mapping each question missed on practice sets back to its underlying concept

  • Diagnose personal weak sub-topics and rank them by expected score impact

Your checkpoint

A timed 60-question mixed mock covering Domains 1-4, scored and fully reviewed, with a ranked weak-topic list driving Weeks 5-8

Week 5

Geomorphology and Surficial Processes & Hydrogeology

  • Interpret drainage patterns and stream longitudinal profiles to infer lithologic and tectonic controls

  • Classify mass-wasting types and rank the factors that control slope stability in a given scenario

  • Apply Darcy's Law to compute flow rate, specific discharge, and travel time in confined and unconfined aquifers

  • Read a potentiometric surface map to determine flow direction, gradient, and discharge and recharge areas

Your checkpoint

A worked problem set of 10 quantitative geomorphology and hydrogeology problems, all correct after a single revision pass, with formulas and unit conversions shown

Week 6

Hydrogeology & General Geology and Earth Materials

  • Estimate transmissivity and storativity from drawdown-versus-time pumping-test data

  • Evaluate well design, well interference, capture zones, and saltwater-intrusion risk for a coastal setting

  • Apply retardation, dispersion, and sorption concepts to predict contaminant migration from a release point

  • Distinguish aquifer types, perched and vadose-zone water, and the meaning of specific yield versus specific retention

Your checkpoint

A one-page aquifer-test interpretation for a synthetic site reporting T, S, and hydraulic conductivity, ending in a defensible pumping-rate recommendation

Week 7

Engineering Geology and Geohazards & Geomorphology and Surficial Processes

  • Quantify landslide, seismic, and karst hazards using standard indices and site parameters

  • Compute RQD and apply rock-mass classification to judge excavation and slope stability

  • Distinguish earthquake magnitude from intensity and assess liquefaction susceptibility from grain size and water-table depth

  • Evaluate ore-deposit types against their tectonic settings, and separate conventional from unconventional hydrocarbon systems and reserve terminology

Your checkpoint

Two 300-word site-assessment write-ups, one geohazard and one resource-focused, each with correct calculations and an explicit recommendation

Week 8

General Geology and Earth Materials & Mineralogy, Petrology, and Geochemistry

  • Re-drill the three lowest-scoring domains from the Week 4 error log

  • Complete a full-length timed practice exam under test-day conditions

  • Reconcile every remaining error to a specific concept or formula and re-solve it unaided

  • Consolidate formulas and definitions into a single final review sheet

Your checkpoint

A full-length timed practice exam scored at 75% or higher overall with no domain below 60%, plus a one-page final review sheet

Milestones

Week 2: Foundations baseline: score 80%+ on the mineral/rock reference quiz and 88%+ on the stratigraphy quiz, confirming Domains 1-3 fundamentals are solid before structural work begins

Week 4: Midpoint checkpoint: 60-question mock over Domains 1-4 completed under time pressure, with a written ranked list of weak sub-topics and a revised plan for Weeks 5-8

Week 6: Quantitative checkpoint: all 10 Week 5 problems and the aquifer-test interpretation solved with correct units; any formula still unreliable is flagged for Week 8 re-drill

Week 8: Readiness checkpoint: full-length timed exam at 75%+ overall, no single domain below 60%, and every error-log item closed out

ASBOG FG PG exam day

Your checklist

Government-issued photo ID

Bring a current driver's license, passport, or state ID. The name on the ID must match your registration name exactly - if you have a nickname, suffix, or recent name change on file, resolve it with your state board and the testing provider before test day, not at the check-in desk.

Admission / scheduling confirmation

Print or save your appointment confirmation and any authorization letter from your state board. Some centers will not admit a candidate who cannot show the confirmation, and cell-phone lookup at the counter may not be permitted. Confirm with the provider whether a printed copy is required. (needs_review - confirm with the provider)

Confirmation of your registration status with the state board

ASBOG administers the exams, but your state board must have approved you as a candidate before you can sit. Verify approval and that your exam (Fundamentals of Geology vs. Practice of Geology) is correct on your record. (needs_review - confirm with your state board)

Calculator that complies with the current policy

Many administrations restrict calculators to non-programmable, non-graphing models with no stored text or communication capability, and some computer-based deliveries supply an on-screen calculator only. Check the current allowed-device list for your administration. (needs_review - confirm with the provider)

Test-center logistics worked out in advance

Know the exact address, parking or transit plan, building entrance, and check-in window. Test centers are often in office parks or shared facilities; do a dry run or map the walk from parking to the suite. Arrive earlier than the stated check-in time to absorb delays.

Timepiece strategy

Wear a plain analog watch if permitted, or plan to rely on the on-screen timer. Smart watches, fitness trackers, and anything with communication capability are almost always prohibited. (needs_review - confirm with the provider)

Layers and comfort items

Test rooms run hot and cold unpredictably, and you will be seated for hours. Dress in layers, wear glasses rather than contacts if you are prone to dry eyes, and bring only items the provider permits into the room.

Snack and water for the break, stored outside the testing room

Plan a quick, quiet snack and water you can reach during any authorized break. Confirm the break policy - in many computer-based deliveries the clock keeps running during unscheduled breaks - and eat a real meal beforehand so you are not dependent on the break. (needs_review - confirm with the provider)

Pre-approved accommodations arranged

If you need extended time, a separate room, or medical accommodations, approval must be granted well in advance through the state board and provider. Day-of requests are generally not accommodated.

A realistic content-review plan behind you

Bring knowledge, not paper. Reference sheets, textbooks, notes, and flashcards are not permitted at the workstation, so the last review should be consolidation of material you already know: classification schemes, formula relationships, and the standard workflows for the exam domains.

Plan the day

Final 72 hours

Stop learning new topics. Do one or two timed mixed-topic practice sets to rehearse pacing, then spend remaining time on your three weakest domains: typically structural geometry, hydrogeology calculations, and stratigraphic/sedimentologic terminology. Re-read only your own condensed notes. Confirm test-center address, check-in time, ID name match, and calculator policy today so any problem has time to be fixed.

24 hours before

Pack what you are allowed to bring, lay out the ID and confirmation, and set two alarms. Do a light pass over high-yield definitions in the morning only. Protect your sleep schedule - a full night's sleep is worth more than any additional hour of review. Confirm travel time including rush hour, and decide what you will eat for breakfast.

Morning of

Eat a normal meal with protein and moderate caffeine - do not experiment with energy drinks. Arrive earlier than the stated check-in window. Leave your phone, smart watch, and study materials secured outside the testing room rather than arguing at the desk. Use the restroom before check-in. Once seated, take a few slow breaths and read the first question twice before answering.

During the test

Work in passes. First pass: answer everything you know quickly and flag anything requiring a calculation or a second read. Second pass: return to flagged items and work them properly. Third pass: make sure no question is blank before you submit, unless the scoring rules for that administration explicitly penalize incorrect answers (confirm with the provider). Check the clock at predictable intervals rather than constantly - roughly a quarter of the time at a quarter of the questions. For calculation items, sketch the relationship and check units before selecting.

After the test

Do not linger on specific questions - you cannot change them. Note anything you want to review later, but know that scoring and reporting run through ASBOG and your state board, and results are released on their schedule. Ask your board about the retake window and any waiting period now, while it is fresh, in case you need it.

Rules to check

  • You must present valid government-issued photo identification with a name matching your registration exactly. Candidates without acceptable ID are typically turned away and may forfeit the fee.

  • Only items explicitly permitted by the testing provider may enter the testing room. Phones, smart watches, notes, textbooks, and reference materials are prohibited, and most centers require you to store them in a locker or leave them outside.

  • The exam is a closed-book, closed-reference assessment. Any scratch paper or writing materials are supplied by the provider and collected at the end of the session - do not bring your own.

  • Break policy varies by delivery format, and many computer-based sessions do not pause the clock for unscheduled breaks. Confirm your specific break rules and whether an unscheduled break is permitted at all with the provider before test day.

  • Scoring is handled by ASBOG and reported through your state board; passing standards are set psychometrically and are not simply a raw percentage of correct answers. Determine your state's passing standard, score-reporting timeline, and retake policy with your board rather than estimating from a practice-test percentage.

  • Any irregularity - talking, looking at another workstation, an unauthorized device, or accessing prohibited material - can result in removal and invalidation of your score. If something goes wrong at the workstation (equipment failure, interruption, illness), report it to the proctor immediately and follow up in writing, because undocumented problems are hard to remedy afterward.

  • Review the current ASBOG candidate handbook and your state board's examination rules before test day. This guide is general preparation advice; the handbook governs the administration. (needs_review - confirm with the provider)

ASBOG FG PG FAQ

How many ASBOG FG PG practice questions are available?

The practice set has 200 ASBOG FG PG questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many ASBOG FG PG flashcards are available?

The flashcard set has 32 ASBOG FG PG cards. Each card shows the term and its definition.

Which topics does the ASBOG FG PG study material cover?

The ASBOG FG PG study material has 8 sections, including General Geology and Earth Materials, Mineralogy, Petrology, and Geochemistry, and Sedimentology, Stratigraphy, and Paleontology.

What format facts does the catalog list for the ASBOG FG PG exam?

The catalog lists these item types: multiple choice for the ASBOG FG PG exam.