API 570 Practice Test

API 570 Piping Inspector Certification Exam

API 570 overview

  • 200 practice questions
  • 32 flashcards
  • 5 study guide topics
  • 38 key terms

What you'll study

  • Scope, Definitions, and Organization of API 57020%
  • Causes of Deterioration and Failure in Piping Systems20%
  • Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping20%
  • Inspection Practices, Methods, and Referenced Code Requirements20%
  • Records, Reports, and Repair/Replacement Documentation20%

The API 570 Piping Inspector credential is one of the American Petroleum Institute's Individual Certification Programs (ICP). It is intended for inspectors and engineers who evaluate in-service process piping - the fixed piping systems found in refineries, petrochemical plants, tank farms and similar facilities - rather than newly fabricated pipe. Certification signals that a candidate can apply the API 570 standard alongside its companion documents, including the damage-mechanism reference API 571, the inspection-practices guide API 574 and the piping-inspection-code summary API 578, plus the relevant ASME construction and welding codes. The exam is organized around five content areas: scope, definitions and organization of API 570; causes of deterioration and failure in piping systems; inspection, rating, repair, alteration and rerating of in-service piping; inspection practices, methods and referenced code requirements; and records, reports and repair/replacement documentation. Most successful candidates prepare by reading the current editions of those documents cover to cover, working through calculation and rating problems, and pairing study with field experience on real piping circuits. Note that this page is an independent study resource and is not affiliated with or endorsed by API; candidates should confirm current exam logistics, fees and scheduling directly with API.

Common mistakes

On a scope question, treating every pipe on the unit as API 570 piping - for example counting a cross-country crude line, boiler external piping, or instrument/control tubing as in-scope.

The exam tests the scope article's inclusion/exclusion logic, but candidates answer from the everyday meaning of the word 'piping' and never check the exclusions.

What to do instead

Before committing to an answer, ask 'is this item covered by another code or explicitly excluded (pipelines under B31.4/B31.8, boiler external piping, instrument and control tubing, pressure vessels, furnaces, etc.)?' Rehearse the exclusion list until the check is automatic.

Reading a short damage description and pattern-matching to the first familiar mechanism - labelling flow-accelerated/erosion-corrosion as plain general corrosion, or missing corrosion under insulation because 'the pipe looks painted and dry'.

Mechanism names share vocabulary and the exam gives only a line or two of process data, so candidates anchor on a keyword instead of the driving conditions.

What to do instead

For each scenario, extract three facts before choosing: fluid and velocity, temperature/insulation status, and chemistry or contaminants. Then localize: flow-driven thinning shows up at elbows, tees, reducers and downstream of control valves; CUI shows up where the susceptibility window and insulation/water-trapping conditions coincide.

Laying out thickness measurement locations only at the circuit's generic corrosion allowances and leaving injection points, mixing points, and deadlegs out of the plan.

Candidates think of a piping circuit as one uniform corrosion environment and treat these features as fittings rather than as locally severe, separately managed locations.

What to do instead

Independently list every injection point, mixing point (where two streams join), and deadleg in the circuit; give each its own TMLs and a shorter, separately justified inspection interval than the circuit as a whole.

Classifying work as a 'repair' just because welding was involved, or as an 'alteration' only when a new nozzle is added.

The distinction turns on the definition (change of pressure/temperature rating or service fluid, or a physical change in a component), not on the type of workmanship, and candidates classify by activity instead.

What to do instead

Run a two-part test every time: (1) Does it change the pressure rating, temperature rating, or service fluid? (2) Does it physically change a component beyond restoring it to its original condition? Either 'yes' makes it an alteration requiring engineering approval and possible re-rating; restoring original condition is a repair.

Computing remaining life with a rushed formula - subtracting from nominal instead of measured thickness, using only the long-term corrosion rate, or mixing mils per year with millimetres per year.

The arithmetic looks trivial, so candidates do it in their heads under time pressure and skip the short-term versus long-term comparison.

What to do instead

Write the equation before doing arithmetic: remaining life = (measured thickness − minimum required thickness) ÷ corrosion rate. Convert every reading into one unit system, calculate both a short-term rate (from the two most recent readings) and a long-term rate, apply the governing (higher) rate, and round the resulting interval down, not up.

Treating re-rating as a paperwork exercise - recalculating a maximum allowable working pressure at one temperature without re-deriving allowable stress, and assuming re-rating only ever means increasing pressure.

Candidates memorize 're-rating needs an engineer' but not that the calculation is temperature-dependent and bidirectional.

What to do instead

For any re-rate, state that it can be an increase or a decrease; re-derive allowable stress at the new design temperature, verify every component in the circuit (pipe, flanges, valves, fittings, supports), require engineer approval, and then update records and markings accordingly.

Setting an inspection interval from a half-remembered number, or extending an interval because the last inspection found nothing of note.

Candidates memorize class intervals as isolated facts and forget the remaining-life constraint that can shorten them and the justification requirement that governs any extension.

What to do instead

Apply the rules in order: the class-based maximum from the interval table, then the cap tied to estimated remaining life (whichever is shorter governs). A clean inspection history alone is not a basis for exceeding the table maximum; any extension needs documented engineering justification.

Assuming an external visual inspection satisfies corrosion-under-insulation coverage, or selecting an NDE method that does not fit the geometry, material, or access available at the location.

Candidates treat 'inspection' as a single activity and default to the cheapest or most familiar method rather than matching method to mechanism.

What to do instead

Select the method from the damage mechanism and the access: CUI requires insulation removal at representative and suspect locations, not just a walk-by; internal or under-insulation loss needs volumetric or profile techniques, and austenitic or difficult geometries may rule out a method that works on carbon steel.

Writing an inspection summary that states findings but omits required elements - measurement locations and readings, the evaluation of remaining life or fitness, and the authorized inspector's approval.

Candidates narrate what they saw and stop, because in practice the paperwork is filled in by others.

What to do instead

Check the finished answer against a four-part test: what was inspected, what was found (with TMLs and readings), what it means (rate, remaining life, suitability for continued service), and who approved it. If any part is missing, the report is incomplete.

Closing out a repair or alteration without revising the isometrics/drawings and circuit records, or discarding old thickness readings once a report is issued.

Candidates see documentation as the end of the job rather than as an input to the next corrosion-rate calculation.

What to do instead

Treat every repair or alteration as triggering a records update: as-built drawings and isometrics, circuit and TML records, and re-rating documentation, all retained with the equipment file. Keep historical readings - without them, no future short-term or long-term corrosion rate can be calculated.

Exam requirements can change. Confirm current details with the exam provider.

API 570 practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Scope, Definitions, and Organization of API 570

    Which of the following best describes the coverage of API 570?

    1. Design, fabrication, erection, and testing of new metallic piping systems
    2. Inspection, repair, alteration, and rerating of in-service piping Correct answer.
    3. Qualification of welding procedures and welders for new construction work
    4. Inspection, repair, and alteration of in-service pressure vessels and storage tanks

    Explanation

    API 570 is an in-service inspection code whose stated scope is the inspection, repair, alteration, and rerating of in-service metallic piping systems and pipelines. New construction and equipment such as vessels and tanks are covered by other codes.

  2. Question 2Scope, Definitions, and Organization of API 570

    API 570 is written primarily for application to piping systems in which setting?

    1. Power plants designed to ASME B31.1
    2. Petroleum refineries and chemical plants Correct answer.
    3. Nuclear power plants and their safety systems
    4. Commercial buildings and their HVAC systems

    Explanation

    API 570 applies to metallic piping systems and pipelines in refineries, chemical plants, and other process facilities. Nuclear, boiler external, and building-service piping are addressed by other codes and standards.

  3. Question 3Scope, Definitions, and Organization of API 570

    API 570 addresses a piping system at which stage of its life cycle?

    1. During shop fabrication and field erection only
    2. After the piping has been placed in service Correct answer.
    3. Only after the piping has been permanently retired
    4. During initial design and stress analysis

    Explanation

    API 570 is an in-service code: it begins to apply once the piping system has been placed in service and covers ongoing inspection, repair, alteration, and rerating. Design and construction are governed by the applicable construction code.

  4. Question 4Scope, Definitions, and Organization of API 570

    In API 570, the term 'owner/user' refers to:

    1. The manufacturer of the pipe and fittings
    2. The contractor that performs welding on the piping
    3. The organization that operates the piping system Correct answer.
    4. The agency that certifies the piping inspector

    Explanation

    The owner/user is the organization that owns or operates the piping system and is accountable under the code for its inspection and safe operation. Contractors, certifying bodies, and manufacturers are separate parties.

  5. Question 5Scope, Definitions, and Organization of API 570

    Under API 570, which party is responsible for ensuring that piping systems are inspected in accordance with the code?

    1. The owner/user Correct answer.
    2. The inspection contractor
    3. The piping designer
    4. The pipe fabricator

    Explanation

    API 570 places responsibility for inspection of the piping on the owner/user. Contractors and other personnel may perform inspection work, but accountability for the program remains with the owner/user.

  6. Question 6Scope, Definitions, and Organization of API 570

    Which statement defines 'repair' as used in API 570?

    1. Work needed to restore a system to safe operation at the design conditions Correct answer.
    2. The periodic examination of a system to determine its condition
    3. A change that increases pressure-containing capability beyond the original design
    4. A change in the design pressure or design temperature of the system

    Explanation

    Repair is the work necessary to restore a piping system to a condition suitable for safe operation at the design conditions. If the restorative work changes the design pressure or temperature, the rerating requirements must be met.

  7. Question 7Scope, Definitions, and Organization of API 570

    Which statement defines 'alteration' as used in API 570?

    1. Adding insulation or paint to a piping system
    2. Replacing a valve with one of the same rating
    3. Restoring a component to its original dimensions by welding
    4. A change with design implications affecting pressure containment Correct answer.

    Explanation

    An alteration is a physical change in a component that has design implications affecting the pressure-containing capability of the system beyond the scope of the original design. Cosmetic and like-for-like maintenance activities are not alterations.

  8. Question 8Scope, Definitions, and Organization of API 570

    In API 570, the 'remaining life' of a piping component is:

    1. The design life stated on the original drawings
    2. The time before the component reaches t-min Correct answer.
    3. The interval between the last two inspections
    4. The time the component has been in service since installation

    Explanation

    Remaining life is the time a component can continue to be used before its thickness reaches the minimum required thickness, calculated from the measured thickness and the corrosion rate.

  9. Question 9Scope, Definitions, and Organization of API 570

    A repair is completed and it results in a change to the design pressure of the piping system. What does API 570 require?

    1. The work shall be documented as a repair only
    2. The system shall be replaced within one year
    3. No further action, because the work is a repair
    4. The requirements for rerating shall be satisfied Correct answer.

    Explanation

    The definition of repair states that if the restorative work results in a change of design temperature or pressure, the requirements for rerating shall be satisfied. The rerating must also be documented accordingly.

  10. Question 10Scope, Definitions, and Organization of API 570

    Which of the following is an alteration rather than a repair?

    1. Increasing the diameter of a section of the line Correct answer.
    2. Replacing a corroded elbow with one of the same specification
    3. Renewing a gasket of the same type and material
    4. Removing and reinstalling a valve of the same rating

    Explanation

    Changing the size of a section of line is a physical change with design implications beyond the original design, so it must be handled as an alteration. Like-for-like renewal of components is repair or maintenance.

  11. Question 11Scope, Definitions, and Organization of API 570

    In API 570, 'rerating' means:

    1. Recalculating the corrosion rate after an inspection
    2. Replacing a component with one of a higher pressure class
    3. A change in the design pressure and/or design temperature Correct answer.
    4. Restoring the original design conditions after a repair

    Explanation

    Rerating is a change in the design pressure and/or design temperature of a piping system or component, and it may be either an increase or a decrease. It must be carried out in accordance with the applicable design code.

  12. Question 12Scope, Definitions, and Organization of API 570

    API 570 defines a 'repair organization' as an organization that:

    1. Provides third-party inspection of new construction
    2. Manufactures new piping components to an accepted specification
    3. Performs repairs and is responsible for the adequacy of the work Correct answer.
    4. Certifies piping inspectors on behalf of the owner/user

    Explanation

    A repair organization performs repairs, alterations, or rerating of piping systems and is responsible for the adequacy of the work it performs. The owner/user remains responsible for ensuring that only qualified organizations are used.

  13. Question 13Scope, Definitions, and Organization of API 570

    Welding procedures used for repairs and alterations under API 570 shall be qualified in accordance with:

    1. AWS D1.1
    2. ASME BPVC Section VIII Division 1
    3. API 1104
    4. ASME BPVC Section IX Correct answer.

    Explanation

    Welding procedure specifications, procedure qualification records, and welder performance qualification for repairs and alterations must satisfy ASME BPVC Section IX. The repair must also be designed and executed in accordance with the applicable construction code.

  14. Question 14Scope, Definitions, and Organization of API 570

    A piping system has an estimated remaining life of 12 years. Under the remaining-life rule of API 570, the inspection interval shall not exceed:

    1. 4 years
    2. 12 years
    3. 2 years
    4. 6 years Correct answer.

    Explanation

    The inspection interval may not exceed one-half of the estimated remaining life, subject also to the maximum intervals given in the code. One-half of 12 years is 6 years.

  15. Question 15Scope, Definitions, and Organization of API 570

    The measured thickness of a pipe is 0.500 in, the minimum required thickness is 0.350 in, and the corrosion rate is 0.010 in/yr. What is the remaining life?

    1. 15 years Correct answer.
    2. 35 years
    3. 10 years
    4. 20 years

    Explanation

    Remaining life equals the corrosion allowance divided by the corrosion rate: (0.500 minus 0.350) divided by 0.010 in/yr equals 15 years. The inspection interval would then be limited to half of that value.

  16. Question 16Scope, Definitions, and Organization of API 570

    In API 570, a 'piping system' is best described as:

    1. All the piping within a process unit boundary, whatever its service
    2. A single length of pipe between two flanges
    3. Interconnected piping subject to the same operating conditions Correct answer.
    4. The pipe and its structural supports

    Explanation

    A piping system is an assembly of interconnected piping components, such as pipe, fittings, flanges, gaskets, bolting, valves, and pressure-containing parts, that are subject to the same operating conditions and treated as a unit for inspection.

  17. Question 17Scope, Definitions, and Organization of API 570

    Non-destructive examination personnel performing inspections under API 570 shall be qualified in accordance with:

    1. AWS QC1 qualification
    2. API 570 certification of the individual
    3. ASME Section V and SNT-TC-1A Correct answer.
    4. API 510 certification of the inspector

    Explanation

    Examinations are performed in accordance with ASME BPVC Section V, and NDE personnel are qualified to a recognized standard such as ASNT SNT-TC-1A or an equivalent. Certification as a piping inspector alone does not qualify a person to perform NDE.

  18. Question 18Scope, Definitions, and Organization of API 570

    Which document does the owner/user prepare for a piping system, or group of similar systems, to define the inspection tasks, methods, and intervals?

    1. A weld procedure specification
    2. An inspection plan Correct answer.
    3. A rerating calculation
    4. A fitness-for-service report

    Explanation

    API 570 requires the owner/user to develop an inspection plan for each piping system or group of similar systems. The plan defines what will be inspected, how, and at what intervals.

  19. Question 19Scope, Definitions, and Organization of API 570

    Which of the following is a responsibility of the piping inspector under API 570?

    1. Authorizing changes to process operating conditions
    2. Setting the operating budget for the unit
    3. Evaluating inspection results and recommending action Correct answer.
    4. Performing all repairs personally

    Explanation

    The inspector plans and performs inspection work, evaluates the results, and makes recommendations to the owner/user. Operating decisions, budgets, and the actual repair work are outside the inspector's role.

  20. Question 20Scope, Definitions, and Organization of API 570

    In API 570, 't-min' refers to:

    1. The minimum required thickness Correct answer.
    2. The nominal wall thickness ordered for the pipe
    3. The thickness measured at the most recent inspection
    4. The corrosion allowance plus the measured thickness

    Explanation

    t-min is the minimum required thickness determined from the applicable design code. Measured thickness readings are compared with t-min to determine corrosion rate and remaining life.

  21. Question 21Scope, Definitions, and Organization of API 570

    Which statement correctly describes how API 570 relates to ASME B31.3?

    1. API 570 replaces B31.3 once the piping is placed in service
    2. B31.3 covers design; API 570 covers in-service inspection Correct answer.
    3. B31.3 governs in-service inspection while API 570 governs design
    4. The two codes cover different industries and are never used together

    Explanation

    B31.3 provides the design and construction rules for process piping, while API 570 provides the in-service inspection, repair, alteration, and rerating rules. Alterations and rerating performed under API 570 must still satisfy the applicable design code.

  22. Question 22Scope, Definitions, and Organization of API 570

    A 20-ft section of carbon steel line is replaced with stainless steel pipe of the same size and schedule to resist a new corrosive stream. Under API 570 this work is:

    1. An alteration, because the material change affects the design Correct answer.
    2. A repair, because the pipe was replaced and the size did not change
    3. Routine maintenance, which needs no inspection involvement
    4. Neither a repair nor an alteration, because the size did not change

    Explanation

    A change of material alters the design basis, including allowable stress and corrosion assumptions, so it is a physical change with design implications beyond the original design and is an alteration. A replacement using pipe of the original specification would have been a repair.

  23. Question 23Scope, Definitions, and Organization of API 570

    An inspection shows that the minimum measured thickness of a line is below t-min. What does API 570 require?

    1. Immediate scrapping of the entire piping system
    2. Repair, replace, rerate, or show fitness for service Correct answer.
    3. An increase in inspection frequency only
    4. Continued operation until the next scheduled inspection

    Explanation

    Piping below the minimum required thickness is not suitable for the current design conditions. It must be repaired, replaced, or rerated to lower conditions, or it must be shown to be fit for continued service by a fitness-for-service assessment.

  24. Question 24Scope, Definitions, and Organization of API 570

    A piping system shows a long-term corrosion rate of 0.004 in/yr and a short-term corrosion rate of 0.012 in/yr. Which rate governs the remaining life?

    1. The short-term rate, because the greater rate governs Correct answer.
    2. The average of the two rates
    3. The long-term rate, because it uses more data
    4. Neither; remaining life depends only on t-min

    Explanation

    Remaining life is based on the greater of the short-term and long-term corrosion rates so the estimate is conservative. Here the short-term rate of 0.012 in/yr governs, producing a shorter remaining life.

  25. Question 25Scope, Definitions, and Organization of API 570

    A piping system must be operated at a lower design pressure because of wall loss. Under API 570, which of the following is required?

    1. Rerating in accordance with the applicable design code Correct answer.
    2. No action at all, because a lower rating is inherently safe
    3. Replacement of every component with thicker-walled pipe
    4. An entry in the operating log recording the new pressure

    Explanation

    Operating at a pressure lower than the original design is a rerating, and rerating must be performed in accordance with the applicable design code with the change properly documented. Relief protection and records must be consistent with the new rating.

  26. Question 26Scope, Definitions, and Organization of API 570

    API 570 covers the inspection, repair, alteration, and rerating of which of the following?

    1. Aboveground storage tank shells and bottoms
    2. Pressure relief valves installed in process service
    3. Fired heater tubes in the radiant and convection sections
    4. In-service process piping in a petroleum refinery Correct answer.

    Explanation

    API 570 applies to in-service metallic and reinforced thermosetting resin (FRP) piping systems, typically process piping in refineries and chemical plants. Tanks, relief valves, and heater tubes are addressed by other documents because they are not piping systems.

  27. Question 27Scope, Definitions, and Organization of API 570

    Under API 570, which party has overall responsibility for establishing and maintaining the piping inspection program?

    1. The jurisdictional authority that regulates the facility
    2. The authorized inspection agency, whenever one is engaged
    3. The owner/user of the facility Correct answer.
    4. The repair organization that performs repairs on the piping

    Explanation

    API 570 places the responsibility for the inspection program, including inspection plans, intervals, and recordkeeping, on the owner/user. Some activities may be delegated to inspectors or inspection agencies, but the responsibility itself is not transferred.

  28. Question 28Scope, Definitions, and Organization of API 570

    In API 570, the abbreviation CML stands for:

    1. Certified Maintenance Level
    2. Corrosion Monitoring Line
    3. Condition Monitoring Location Correct answer.
    4. Critical Measurement Limit

    Explanation

    A CML is a designated location on a piping circuit where examinations and thickness measurements are made to monitor the condition of the system. CMLs are selected by the inspector and identified on inspection drawings or records.

  29. Question 29Scope, Definitions, and Organization of API 570

    In API 570 terminology, which statement best distinguishes 'examination' from 'inspection'?

    1. Examination is the performance of visual, dimensional, or nondestructive checks; inspection is the broader assessment and evaluation of condition by the inspector. Correct answer.
    2. Examination may be performed by any plant personnel; inspection is restricted to the repair organization.
    3. Examination is the overall fitness-for-service judgment; inspection is the physical measurement of wall thickness.
    4. Examination applies only to welds; inspection applies to all other parts of the piping system.

    Explanation

    Examination refers to the physical activities such as visual checks, dimensional checks, and nondestructive testing. Inspection is the wider function that includes those examinations plus the evaluation and judgment made by the inspector.

  30. Question 30Scope, Definitions, and Organization of API 570

    In API 570, a 'piping circuit' is best described as:

    1. The piping that is drained and ventilated to permit entry during a turnaround
    2. A single spool of pipe between two flanges
    3. All piping within one process unit, from battery limits to battery limits
    4. A section of piping with similar design and service conditions that is treated as a unit for inspection Correct answer.

    Explanation

    API 570 groups piping into circuits so that inspections, corrosion rates, and remaining life can be managed for a representative section rather than for every individual component. A circuit shares similar materials, service, and operating conditions.

  31. Question 31Scope, Definitions, and Organization of API 570

    Which API document is referenced by API 570 for detailed piping inspection practices and techniques?

    1. API 577
    2. API 580
    3. API 574 Correct answer.
    4. API 571

    Explanation

    API 574 is the companion document that describes inspection practices and techniques for piping system components. API 570 states the requirements, while API 574 supplies the supporting how-to guidance.

  32. Question 32Scope, Definitions, and Organization of API 570

    Under API 570, a person acting as an inspector on in-service piping may be employed by:

    1. Only the jurisdictional authority that regulates the plant
    2. The owner/user or an authorized inspection agency Correct answer.
    3. The repair organization that carries out the repairs
    4. Only a third-party inspection company that is independent of the plant

    Explanation

    Inspectors may be employees of the owner/user or of an authorized inspection agency acceptable to the owner/user, such as an insurance inspection organization. Independence from the organization performing the repair work is the key point.

  33. Question 33Scope, Definitions, and Organization of API 570

    In API 570, an 'injection point' is a location where:

    1. Two piping systems of different materials are joined by a flanged connection
    2. A fluid such as a chemical or wash water is injected into the process stream Correct answer.
    3. A piping circuit crosses the battery limits of a process unit
    4. A branch connection is provided for a pressure instrument

    Explanation

    Injection points are singled out because the injected stream can mix with the process fluid and cause locally accelerated corrosion, erosion, or cracking. API 570 requires that these locations be specifically identified and included in the inspection plan.

  34. Question 34Scope, Definitions, and Organization of API 570

    In API 570, the maximum allowable working pressure (MAWP) of a piping system is:

    1. The pressure that was used for the original hydrostatic test of the system
    2. The highest pressure the system has actually experienced during operation
    3. The maximum internal pressure permitted at the design temperature, accounting for the current condition of the system Correct answer.
    4. The pressure at which the relief valve on the system is set to open

    Explanation

    MAWP is a design and condition-based limit, determined at the design temperature and adjusted for any wall loss or deterioration found in service. It is not an operating history value or a test pressure.

  35. Question 35Scope, Definitions, and Organization of API 570

    Which of the following is an example of a deadleg in a piping system?

    1. A standby pump suction line that is isolated by a closed valve and has no normal flow Correct answer.
    2. A header that continuously carries process fluid to several users
    3. The section of line immediately downstream of a control valve in continuous service
    4. A line that is being steam flushed during a unit start-up

    Explanation

    A deadleg is a portion of piping that does not have a continuous flow, such as a standby branch, bypass, or vent that is normally closed. These stagnant sections can accumulate corrosive fluids and are therefore given attention in the inspection plan.

  36. Question 36Scope, Definitions, and Organization of API 570

    Inspection of which of the following is governed by a separate API standard rather than by API 570?

    1. Block valves in process service
    2. Flanges and their bolting
    3. Pressure relief valves Correct answer.
    4. Pipe fittings such as elbows, tees, and reducers

    Explanation

    Relief valves are covered by API 576, while API 570 covers the piping system itself, which includes pipe, fittings, flanges, bolting, gaskets, and valves. The inspection of a relief valve is therefore handled under a different standard.

  37. Question 37Scope, Definitions, and Organization of API 570

    In API 570, the corrosion rate of a piping circuit is:

    1. The difference between the nominal thickness and the lowest measured thickness
    2. The total metal loss measured since the piping was placed in service
    3. The rate of metal loss with time, calculated from thickness measurements taken over an interval Correct answer.
    4. The thickness below which the component must be removed from service

    Explanation

    Corrosion rate is expressed as metal loss per unit time and is computed from thickness data gathered at condition monitoring locations. API 570 uses both long-term and short-term rates, and the higher of the applicable rates governs the remaining-life calculation.

  38. Question 38Scope, Definitions, and Organization of API 570

    An owner/user wants to use risk-based inspection to establish inspection intervals for piping under API 570. Which documents provide the RBI methodology referenced by API 570?

    1. API 510 and API 653
    2. API 570 and API 574
    3. API 579-1/ASME FFS-1
    4. API 580 and API 581 Correct answer.

    Explanation

    API 570 permits inspection intervals to be set using risk-based inspection in accordance with API 580 and API 581. Those documents supply the risk assessment methodology that the piping code relies on.

  39. Question 39Scope, Definitions, and Organization of API 570

    A flaw is found in a piping system, and the remaining strength cannot be evaluated using the rules of API 570. Which document does API 570 point to for a fitness-for-service assessment?

    1. ASME B31.3
    2. API 574
    3. API 577
    4. API 579-1/ASME FFS-1 Correct answer.

    Explanation

    API 570 allows a fitness-for-service assessment in accordance with API 579-1/ASME FFS-1 when the condition falls outside the evaluation rules of the piping code. The assessment determines whether the component can continue to be operated safely.

  40. Question 40Scope, Definitions, and Organization of API 570

    Under API 570, inspection and repair records for a piping system are to be retained:

    1. Only until the process unit is sold or ownership changes
    2. For the life of the piping system Correct answer.
    3. Until the next scheduled inspection has been completed
    4. For a minimum of five years after the record is created

    Explanation

    API 570 requires the owner/user to keep inspection, repair, and alteration records for the life of the piping system. These records support corrosion-rate determination, remaining-life calculation, and later rerating or fitness-for-service evaluations.

  41. Question 41Causes of Deterioration and Failure in Piping Systems

    Uniform general corrosion of carbon steel piping is characterized by which of the following?

    1. Thinning at a fairly even rate over the wetted surface Correct answer.
    2. Deep isolated pits that penetrate rapidly through the wall
    3. Cracks that follow grain boundaries in the heat-affected zone
    4. Metal loss confined to a narrow band at the weld toe

    Explanation

    General corrosion attacks the surface broadly and produces relatively uniform wall loss, so it is evaluated by averaging thickness readings over an area and computing a corrosion rate. The other patterns are localized forms that require different inspection strategies.

  42. Question 42Causes of Deterioration and Failure in Piping Systems

    What is the essential condition for external corrosion under insulation (CUI) to occur on carbon steel?

    1. Trapped moisture at the steel surface Correct answer.
    2. Sustained metal temperatures above 500 °F (260 °C)
    3. Frequent cyclic operation of the piping system
    4. Insulation that contains chlorides only

    Explanation

    CUI is an aqueous corrosion process, so water must be present at the steel surface; insulation, jacketing damage, and the temperature range influence whether that water persists but do not replace it. Carbon steel CUI is most aggressive in the roughly 10 °F to 350 °F metal temperature band where wetting and evaporation cycles occur.

  43. Question 43Causes of Deterioration and Failure in Piping Systems

    In a galvanic couple between carbon steel and a copper alloy in an electrolyte, which metal corrodes?

    1. The carbon steel, because it is anodic Correct answer.
    2. The copper alloy, because it is the cathode
    3. Both metals at rates that are always equal
    4. Neither metal, because the couple stops all corrosion

    Explanation

    In a galvanic couple the more active metal, which is anodic in the galvanic series, corrodes while the more noble metal becomes the cathode and is protected. Carbon steel is anodic to copper alloys in most aqueous environments, so the steel suffers accelerated attack, with severity strongly influenced by the cathode-to-anode area ratio.

  44. Question 44Causes of Deterioration and Failure in Piping Systems

    Severe erosion-corrosion in carbon steel piping is most likely at which location?

    1. On the outside radius of an elbow in wet steam Correct answer.
    2. On the upstream face of a fully open gate valve
    3. Along a long straight run of pipe with steady laminar flow
    4. In a dead leg where there is essentially no flow

    Explanation

    Erosion-corrosion is driven by high local velocity and turbulence, which strip the protective oxide film and expose bare metal to fresh corrodent. The outside radius of an elbow carrying wet steam combines high velocity, changing direction, and two-phase flow, making it a classic location for rapid metal loss.

  45. Question 45Causes of Deterioration and Failure in Piping Systems

    Stress corrosion cracking requires the simultaneous presence of which three conditions?

    1. Susceptible alloy, corrosive environment, tensile stress Correct answer.
    2. High hardness, low temperature, and cyclic loading
    3. Hydrogen, a weld defect, and low hardness
    4. A susceptible alloy, oxygen, and a compressive residual stress

    Explanation

    SCC occurs only when a susceptible alloy is exposed to a specific cracking environment while under sustained tensile stress, whether applied or residual. Removing any one of the three legs prevents cracking, which is the basis for mitigation by stress relief, environment control, or material upgrade.

  46. Question 46Causes of Deterioration and Failure in Piping Systems

    Hydrogen blistering of carbon steel in wet sour service occurs by which sequence?

    1. Hydrogen ions react with carbides to form methane at grain boundaries
    2. Sulfide scales lift the surface layer away from the base metal
    3. Atomic hydrogen diffuses in and recombines at inclusions Correct answer.
    4. Dissolved carbon dioxide expands inside laminations on pressure release

    Explanation

    Corrosion in wet sour service generates atomic hydrogen that enters the steel and recombines to molecular hydrogen at inclusions, laminations, and other planar discontinuities. The trapped gas cannot diffuse out, so pressure builds and deforms the steel into blisters, often accompanied by stepwise internal cracking.

  47. Question 47Causes of Deterioration and Failure in Piping Systems

    Which atmospheric condition most accelerates external corrosion of uncoated carbon steel piping?

    1. Dry desert air with very low relative humidity
    2. Repeated wetting with chloride-laden moisture Correct answer.
    3. Continuous sub-zero temperatures
    4. Clean air that carries no contaminants

    Explanation

    Atmospheric corrosion needs a thin electrolyte film, so alternating wet and dry cycles with chloride contamination are far more aggressive than steady exposure. Chlorides raise conductivity and break down protective films, and the drying cycle concentrates them at the surface.

  48. Question 48Causes of Deterioration and Failure in Piping Systems

    Creep damage in carbon steel piping becomes a concern under which condition?

    1. Short-term loading at ambient temperature
    2. Hydrogen charging during a shutdown
    3. Sustained stress at metal temperatures above about 800 °F Correct answer.
    4. Cyclic stress applied at high frequency at room temperature

    Explanation

    Creep is time-dependent deformation that becomes significant when carbon steel operates above roughly 800 °F (425 °C) under sustained stress. It shows up as diametral growth, sagging, and eventually intergranular creep cracking, so hot lines are monitored by periodic dimensional checks.

  49. Question 49Causes of Deterioration and Failure in Piping Systems

    Which set of conditions most favors chloride stress corrosion cracking of 300-series stainless steel?

    1. Dry chloride salt with no moisture present
    2. Anhydrous ammonia under high flow
    3. Warm chloride solution, tensile stress, and dissolved oxygen Correct answer.
    4. Cold concentrated chloride solution under compressive stress

    Explanation

    Austenitic stainless steels crack in chloride environments when tensile stress is present and the metal is warm enough, generally above about 140 °F (60 °C), with oxygen supporting the crack chemistry. Residual weld stress often supplies the stress even when no external load exists.

  50. Question 50Causes of Deterioration and Failure in Piping Systems

    A carbon steel line carrying hydrogen at elevated temperature shows internal fissures and decarburization along grain boundaries. Which damage mechanism is indicated?

    1. High-temperature hydrogen attack Correct answer.
    2. Sulfide stress cracking of hard weld zones
    3. Caustic stress corrosion cracking
    4. Chloride stress corrosion cracking

    Explanation

    Above roughly 400 °F, hydrogen reacts with carbides in steel to form methane that cannot diffuse out, so pressure builds at grain boundaries and produces fissuring together with decarburization. The Nelson curves give the temperature and hydrogen partial pressure limits for each steel grade.

  51. Question 51Causes of Deterioration and Failure in Piping Systems

    Caustic stress corrosion cracking of carbon steel is most often associated with which situation?

    1. Neutral brine at ambient temperature
    2. Hot concentrated caustic with residual stress Correct answer.
    3. Dry caustic soda stored below 100 °F
    4. Dilute caustic flowing at high velocity without stress

    Explanation

    Caustic cracking of carbon steel requires a concentrated caustic solution, elevated temperature, and sustained tensile stress, usually residual stress from welding. Concentration commonly occurs by evaporation at a wetted-dry interface, under deposits, or in a localized hot spot.

  52. Question 52Causes of Deterioration and Failure in Piping Systems

    Which cracking mechanism is caused by wet hydrogen sulfide service acting on hard weld heat-affected zones in carbon steel?

    1. Sulfide stress cracking Correct answer.
    2. Chloride stress corrosion cracking
    3. Caustic embrittlement
    4. Polythionic acid cracking

    Explanation

    Sulfide stress cracking is hydrogen-assisted cracking of carbon and low-alloy steels exposed to wet H2S, and it is strongly favored by high hardness such as that found in unrelieved weld heat-affected zones. Hardness limits and post-weld heat treatment are the usual controls.

  53. Question 53Causes of Deterioration and Failure in Piping Systems

    Sulfidation of steel piping at elevated temperature is mitigated primarily by which means?

    1. Adding chlorides to the process stream
    2. Increasing the chromium content of the steel Correct answer.
    3. Applying a zinc-rich paint to the hot surface
    4. Raising the operating temperature of the line

    Explanation

    Sulfidation resistance depends on the formation of a protective chromium sulfide scale, so resistance improves markedly as chromium content rises from carbon steel through 5 Cr and 9 Cr alloys. Lowering temperature also reduces the rate but does not replace alloy selection.

  54. Question 54Causes of Deterioration and Failure in Piping Systems

    Naphthenic acid corrosion in crude and vacuum units is characterized by which of the following?

    1. Uniform thinning of 316 stainless steel piping
    2. Severe metal loss in high-velocity hot sections with high TAN Correct answer.
    3. Attack concentrated in cold low-velocity sections below 200 °F
    4. Cracking along grain boundaries in the weld heat-affected zone

    Explanation

    Naphthenic acid attack occurs typically between about 350 °F and 700 °F and intensifies with higher total acid number and higher velocity, producing sharp-edged grooves and wake patterns. Molybdenum-bearing stainless steels such as 316 are considerably more resistant than carbon steel.

  55. Question 55Causes of Deterioration and Failure in Piping Systems

    Polythionic acid SCC of sensitized austenitic stainless steel typically occurs during which period?

    1. On shutdown when sulfur deposits meet moist air Correct answer.
    2. While the line is at normal operating temperature
    3. Only during hydrostatic testing with treated water
    4. During continuous operation with dry gas

    Explanation

    Iron sulfide and sulfur deposits react with moisture and oxygen during shutdown to form polythionic acids, which crack sensitized austenitic stainless steel along grain boundaries. The standard control is a soda ash neutralization wash followed by drying and purging with dry nitrogen.

  56. Question 56Causes of Deterioration and Failure in Piping Systems

    Microbiologically influenced corrosion (MIC) in piping usually appears as which of the following?

    1. Localized pitting under deposits or in stagnant zones Correct answer.
    2. Blistering with stepwise internal cracks
    3. Cracking that follows prior austenite grain boundaries
    4. Uniform wall loss around the entire circumference of the pipe

    Explanation

    Bacteria grow in sessile colonies beneath deposits and in low-flow areas, where their metabolic products such as sulfides and organic acids concentrate and attack the metal. The result is typically localized pitting, often with a characteristic black or slimy deposit, rather than generalized thinning.

  57. Question 57Causes of Deterioration and Failure in Piping Systems

    Which feature distinguishes flow-accelerated corrosion from erosion-corrosion caused by suspended solids?

    1. Metal loss without particle impingement Correct answer.
    2. Damage limited to the external surface of the pipe
    3. Cracks opened by cyclic thermal stress
    4. Pits hidden beneath black magnetite tubercles

    Explanation

    Flow-accelerated corrosion is the dissolution of the protective magnetite layer by flowing water or wet steam, enhanced by mass transfer at high velocity, and it needs no entrained solids. Solid-particle erosion-corrosion adds a mechanical component that removes metal and the oxide film by impact.

  58. Question 58Causes of Deterioration and Failure in Piping Systems

    Vapor bubble collapse causing cavitation damage in piping is most likely to be found where?

    1. Along the inner wall of a fully flooded bypass line
    2. Downstream of a partially closed control valve Correct answer.
    3. At the top of a vertical riser with low velocity
    4. On the suction side of a strainer in laminar flow

    Explanation

    Cavitation occurs where local pressure drops below the vapor pressure and bubbles subsequently collapse against the metal, producing mechanical pitting and noise. A throttling control valve creates a low-pressure vena contracta followed by pressure recovery, so collapse damage appears just downstream.

  59. Question 59Causes of Deterioration and Failure in Piping Systems

    In flue gas containing sulfur trioxide and water vapor, sulfuric acid dew point corrosion occurs when which condition is met?

    1. The gas velocity drops below 3 ft/s in the stack
    2. The gas is completely dry and free of sulfur trioxide
    3. The flue gas stays above the water dew point throughout
    4. The metal surface falls below the acid dew point Correct answer.

    Explanation

    Sulfur trioxide combines with water vapor to form sulfuric acid, which condenses on any surface cooler than the acid dew point, typically in the 280 °F to 300 °F range for many flue gases. That is why air preheaters, stack tops, and cold-end ductwork suffer acid attack when metal temperature drops.

  60. Question 60Causes of Deterioration and Failure in Piping Systems

    Vibration-induced fatigue in small-bore piping connections usually begins where?

    1. In the body of an isolation valve
    2. At the flange face of the main line
    3. At the weld toe of the branch connection Correct answer.
    4. At the mid-span of the unsupported branch run

    Explanation

    High-cycle vibration fatigue initiates at the point of highest stress concentration, which for a small-bore branch is normally the weld toe at the branch-to-run connection. Cracks start at the surface, propagate with continued cycling, and can lead to complete failure of the unsupported branch.

  61. Question 61Causes of Deterioration and Failure in Piping Systems

    Prolonged exposure of 300-series stainless steel at 950–1650 °F (510–900 °C) can cause which damage?

    1. Graphitization with breakdown of the carbide structure
    2. Spheroidization of pearlite with general softening of the steel
    3. Sigma phase formation and loss of toughness Correct answer.
    4. 885 °F embrittlement of the ferrite phase

    Explanation

    In this temperature range chromium and molybdenum segregate into sigma phase, a hard intermetallic that lowers toughness and corrosion resistance, especially in cast or high-ferrite weldments. The effect is time and temperature dependent and is the reason such exposure is limited or followed by solution annealing.

  62. Question 62Causes of Deterioration and Failure in Piping Systems

    Brittle fracture of carbon steel piping is most likely under which combination of conditions?

    1. High temperature with slowly applied stress
    2. Low temperature, a sharp flaw, and high restraint Correct answer.
    3. Warm metal, low restraint, and high toughness
    4. Cyclic loading at low stress amplitude

    Explanation

    Brittle fracture requires low material toughness, which is favored by low temperature and by a sharp flaw that concentrates stress, together with high restraint that prevents yielding. Failure occurs with little or no deformation, often shortly after a cold start-up or a pressure surge.

  63. Question 63Causes of Deterioration and Failure in Piping Systems

    Selective leaching (dezincification) of brass piping results in which change to the metal?

    1. The metal forms a tight protective sulfide film
    2. The zinc content increases at the metal surface
    3. The alloy becomes harder and fully resistant to further attack
    4. A porous copper-rich residue replaces the brass Correct answer.

    Explanation

    In dezincification, zinc preferentially dissolves from the brass, leaving a weak, porous copper sponge behind; either plug type or layer type attack may occur. The affected area loses strength and is often identifiable by a copper-colored surface on the corroded pipe.

  64. Question 64Causes of Deterioration and Failure in Piping Systems

    Temper embrittlement of 2.25Cr-1Mo steel is caused by which condition?

    1. Long-term exposure to hydrogen at low pressure
    2. Slow cooling through the 650–1100 °F range after tempering Correct answer.
    3. Rapid quenching from the normalizing temperature
    4. Cyclic thermal stress during start-up

    Explanation

    Impurity elements such as phosphorus, tin, antimony, and arsenic segregate to prior austenite grain boundaries during slow cooling through roughly 650 °F to 1100 °F, raising the ductile-to-brittle transition temperature. The steel may be restored by reheat treatment, but re-embrittlement can occur with further slow cooling.

  65. Question 65Causes of Deterioration and Failure in Piping Systems

    Carbonate stress corrosion cracking of carbon steel in refinery service is most likely where?

    1. In stainless steel welds exposed to chlorides
    2. In cast iron valves handling caustic at ambient temperature
    3. In unrelieved welds wetted by carbonate solutions Correct answer.
    4. In annealed pipe carrying dry hydrocarbon

    Explanation

    Carbonate SCC occurs in carbon steel exposed to carbonate and bicarbonate-bearing water, such as in FCC gas concentration and hydroprocessing units, and is strongly favored by high residual stress and hardness in unrelieved welds. Post-weld heat treatment and hardness control are the standard preventive measures.

  66. Question 66Causes of Deterioration and Failure in Piping Systems

    A carbon steel pipe that operated for many years at about 850 °F (455 °C) is removed from service and sectioned. Metallography shows nodules of graphite in the weld heat-affected zone. Which damage mechanism has occurred?

    1. Graphitization of the carbide phase Correct answer.
    2. Spheroidization of lamellar pearlite
    3. Sigma phase formation
    4. Temper embrittlement

    Explanation

    Carbon and carbon-molybdenum steels exposed above roughly 800 °F (425 °C) can decompose iron carbide into graphite nodules, and the weld heat-affected zone is a favored site. The damage is metallurgical and irreversible, and the graphite nodules act as internal stress raisers.

  67. Question 67Causes of Deterioration and Failure in Piping Systems

    Localized pitting attack caused by dissolved oxygen in carbon steel piping is most likely to develop under which circumstance?

    1. In a line in steady, continuous wet service
    2. In a fully flooded line kept under a nitrogen blanket
    3. In idle or standby lines where wet steel is exposed to air Correct answer.
    4. In a dry gas line operating above the water dew point

    Explanation

    Oxygen pitting requires free oxygen dissolved in a water phase, and it concentrates where water sits stagnant and air can enter, such as idle, drained, or intermittently used lines. Continuous wet service with deaerated water and dry gas service do not supply the oxygen and water needed.

  68. Question 68Causes of Deterioration and Failure in Piping Systems

    A carbon steel pipe is joined to a stainless steel pipe and both are wetted by the same conductive process water. What is the expected corrosion behavior?

    1. The stainless steel is more active and corrodes preferentially
    2. The carbon steel acts as the anode and corrodes faster Correct answer.
    3. Corrosion is confined to the stainless steel heat-affected zone
    4. Neither metal corrodes because both are iron-base alloys

    Explanation

    In a galvanic couple the metal higher in the galvanic series (carbon steel) becomes the anode and suffers accelerated dissolution, while the more noble stainless steel becomes the cathode. The severity grows with the conductivity of the electrolyte and the area ratio of cathode to anode.

  69. Question 69Causes of Deterioration and Failure in Piping Systems

    A buried, coated carbon steel pipeline running parallel to a DC transit system develops rapid external corrosion at a coating holiday. Which cause is most probable?

    1. Microbiologically influenced corrosion
    2. Stray direct current discharging from the pipe Correct answer.
    3. Galvanic action between coating and pipe
    4. Concentration cell action from soil variability

    Explanation

    Stray DC current picked up along the pipeline leaves the metal at a coating holiday, and the anodic discharge site corrodes at a rate proportional to the current density. The damage is highly localized and can be very rapid compared with ordinary soil corrosion.

  70. Question 70Causes of Deterioration and Failure in Piping Systems

    In a hydroprocessing reactor effluent system, corrosion by ammonium bisulfide is made most severe by which combination of conditions?

    1. Neutral water containing no dissolved salts
    2. Dry gas service well above the water dew point
    3. High ammonium bisulfide concentration with high velocity Correct answer.
    4. Low ammonium bisulfide concentration with low velocity

    Explanation

    Ammonium bisulfide corrosion is a wet, aqueous mechanism whose rate rises sharply with salt concentration and with velocity or shear stress that destroys the protective sulfide film. Above the water dew point no aqueous phase exists, and dilute low-velocity streams are comparatively benign.

  71. Question 71Causes of Deterioration and Failure in Piping Systems

    Sigma phase formation in 300-series austenitic stainless steel piping is undesirable primarily because sigma:

    1. Reduces toughness and embrittles the metal Correct answer.
    2. Raises ductility at operating temperature
    3. Lowers the thermal expansion to match carbon steel
    4. Improves resistance to chloride pitting

    Explanation

    Sigma is a hard, brittle intermetallic that precipitates in austenitic stainless steels during prolonged exposure roughly between 1000 °F and 1700 °F (540–900 °C), especially in molybdenum-bearing grades. Its presence sharply lowers toughness and corrosion resistance, so the steel may crack under thermal cycling or impact.

  72. Question 72Causes of Deterioration and Failure in Piping Systems

    A carbon steel header shows internal cracking at the point where a hot process stream is mixed with a cold quench stream. The most likely mechanism is:

    1. Hydrogen blistering
    2. Caustic stress corrosion cracking
    3. Microbiologically influenced corrosion
    4. Thermal fatigue Correct answer.

    Explanation

    Mixing streams of different temperatures produces rapid, cyclic surface temperature swings and restrained thermal strains, and repeated cycles initiate and grow fatigue cracks at the mixing zone. The cracks typically start on the wetted surface and propagate without the need for a corrosive species.

  73. Question 73Causes of Deterioration and Failure in Piping Systems

    Corrosion of carbon steel in wet CO2-containing gas piping is governed primarily by which factor?

    1. The presence of an iron sulfide film
    2. The oxygen content of the gas
    3. The CO2 partial pressure together with free water Correct answer.
    4. The total system pressure alone

    Explanation

    Sweet corrosion requires water as the electrolyte, and its rate rises with the partial pressure of CO2 because that sets the carbonic acid concentration. Protective iron carbonate scale may form and reduce the rate, but the driving condition is CO2 partial pressure plus a water phase.

  74. Question 74Causes of Deterioration and Failure in Piping Systems

    External chloride stress corrosion cracking of austenitic stainless steel piping is most likely to occur under which condition?

    1. Wet, chloride-bearing insulation on a stressed pipe Correct answer.
    2. Buried pipe with an operating cathodic protection system
    3. Dry, chloride-free insulation on a hot pipe
    4. Cooling water service below 100 °F (38 °C)

    Explanation

    External chloride SCC requires a concentrated chloride solution in contact with a susceptible alloy that carries tensile stress, and thermal insulation that becomes wet can trap and concentrate chlorides at the metal surface. The cracking initiates on the outside surface and is a common form of corrosion under insulation damage.

  75. Question 75Causes of Deterioration and Failure in Piping Systems

    Which service condition promotes stress corrosion cracking of brass and other copper alloy piping?

    1. Ammonia or ammonium compounds with moisture and residual stress Correct answer.
    2. Steam service above 800 °F (427 °C)
    3. Neutral water containing only dissolved oxygen
    4. Dry hydrocarbon free of nitrogen compounds

    Explanation

    Copper alloys are susceptible to ammonia SCC, in which ammonia or ammonium species in the presence of moisture attack the metal while residual or applied tensile stress opens cracks. Avoiding ammonia exposure, stress relieving, and controlling water chemistry are typical preventive measures.

  76. Question 76Causes of Deterioration and Failure in Piping Systems

    Metal dusting of low-alloy steel piping in reformer and syngas service is favored by which environment?

    1. Wet sour water at ambient temperature
    2. Carbon monoxide-rich gas at 900–1500 °F (480–815 °C) with low sulfur Correct answer.
    3. High oxygen potential with abundant steam
    4. Hydrogen sulfide-rich gas at low carbon activity

    Explanation

    Metal dusting is a high-temperature carburization phenomenon in which carbon diffuses into the steel and forms a brittle carbide that degrades into dust, and it is promoted by high carbon activity gases such as CO and by low sulfur, which normally inhibits carbon ingress. It typically occurs in the 900–1500 °F (480–815 °C) range.

  77. Question 77Causes of Deterioration and Failure in Piping Systems

    Long-term exposure of carbon steel piping to about 850–1300 °F (455–700 °C) produces spheroidization, which results in which change?

    1. Carbide coalescing into spheroids and a loss of strength Correct answer.
    2. An increase in hardness and tensile strength
    3. Selective loss of chromium from the surface
    4. Formation of graphite nodules along grain boundaries

    Explanation

    Spheroidization is the gradual transformation of lamellar pearlite carbide into rounded particles, which reduces the strengthening effect of the lamellae. The result is a drop in tensile strength, hardness, and creep resistance without any change in the overall chemistry.

  78. Question 78Causes of Deterioration and Failure in Piping Systems

    885 °F (475 °C) embrittlement is a damage mechanism that must be considered for which piping material?

    1. Austenitic stainless steels containing molybdenum
    2. 2.25Cr-1Mo low alloy steel
    3. Ferritic and duplex stainless steels Correct answer.
    4. Nickel-copper alloys

    Explanation

    Alloys containing more than about 12 percent chromium in the ferritic structure, including ferritic and duplex stainless steels, can undergo spinodal decomposition when held in the range of roughly 600–1000 °F (320–540 °C). The result is a marked loss of toughness and an increase in hardness that can lead to brittle failure.

  79. Question 79Causes of Deterioration and Failure in Piping Systems

    Which statement correctly describes corrosion fatigue in piping?

    1. It requires a static stress above a distinct endurance limit
    2. It produces intergranular cracks following prior austenite grain boundaries
    3. It occurs only above 800 °F (427 °C) within the creep range
    4. Cyclic stress in a corrosive environment cracks metal at stresses below the air fatigue limit Correct answer.

    Explanation

    Corrosion fatigue results from the combined action of cyclic stress and a corrosive environment, and the environment removes the true endurance limit so failure can occur at stress levels that would be safe in dry air. Cracks are typically transgranular and may initiate at corrosion pits that act as stress concentrators.

  80. Question 80Causes of Deterioration and Failure in Piping Systems

    In an HF alkylation unit, carbon steel is widely used for anhydrous hydrofluoric acid service because:

    1. A protective iron fluoride film forms on the steel surface Correct answer.
    2. Nickel alloys dissolve rapidly in HF
    3. HF is noncorrosive to iron at any water content
    4. Low operating temperature prevents any reaction with iron

    Explanation

    Carbon steel is acceptable for anhydrous HF because a tightly adherent iron fluoride film forms and limits further attack, which is why it is the standard material for much of the unit. Dilution of the acid with water and high velocity can break down this film and accelerate corrosion, so these variables are controlled.

  81. Question 81Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A piping circuit has a current measured thickness of 0.470 in, a minimum required thickness of 0.320 in, and a corrosion rate of 0.005 in/yr. What is the remaining life?

    1. 15 years
    2. 30 years Correct answer.
    3. 94 years
    4. 64 years

    Explanation

    Remaining life is the difference between the current thickness and the minimum required thickness divided by the corrosion rate: (0.470 - 0.320) / 0.005 = 30 years.

  82. Question 82Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A pipe was measured at 0.500 in at the previous inspection 5 years ago and measures 0.450 in today. What is the corrosion rate?

    1. 0.005 in/yr
    2. 0.100 in/yr
    3. 0.010 in/yr Correct answer.
    4. 0.050 in/yr

    Explanation

    Corrosion rate is the metal loss divided by the elapsed time: (0.500 - 0.450) / 5 = 0.010 in/yr.

  83. Question 83Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which of the following is classified as an alteration of a piping system rather than a repair?

    1. Replacing a corroded elbow with an identical elbow
    2. Changing the service fluid to a more severe one Correct answer.
    3. Building up a thinned area with weld metal
    4. Replacing a leaking gasket at a flange joint

    Explanation

    An alteration is a change with design implications, such as a change in service that affects the design conditions or pressure-containing capability beyond the original design. Replacing like-for-like components, weld build-up of thinned areas, and gasket replacement are repairs or maintenance.

  84. Question 84Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Welding procedures and welder performance for piping repairs shall be qualified in accordance with which document?

    1. API 579-1/ASME FFS-1
    2. ASME BPVC Section IX Correct answer.
    3. API 570
    4. ASME B31.3

    Explanation

    ASME Boiler and Pressure Vessel Code, Section IX, governs qualification of welding procedures and welder performance. B31.3 and API 570 require that repairs use procedures and welders qualified to Section IX.

  85. Question 85Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A hydrostatic test of a repaired piping system is normally conducted at what pressure in accordance with ASME B31.3?

    1. 1.5 times the design pressure Correct answer.
    2. 2.0 times the design pressure
    3. 1.25 times the design pressure
    4. 1.0 times the design pressure

    Explanation

    ASME B31.3 sets the hydrostatic test pressure at 1.5 times the design pressure, with allowance for the temperature difference between test and design conditions.

  86. Question 86Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    The maximum allowable working pressure of an existing piping system is established by:

    1. the pressure capability of the weakest component Correct answer.
    2. the set pressure of the system relief valve
    3. the last hydrotest pressure divided by 1.5
    4. the design pressure of the largest pipe in the line

    Explanation

    A piping system can be no stronger than its weakest element, so the MAWP is limited by the component with the lowest pressure capability at the design temperature. Pipe, fittings, flanges, and valves must all be evaluated.

  87. Question 87Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which statement about temporary repairs to in-service piping is correct?

    1. They are permitted only in water service
    2. They are documented and scheduled for permanent repair Correct answer.
    3. They require no approval from the inspector
    4. They may remain in service indefinitely without leakage

    Explanation

    Temporary repairs such as clamps or enclosures must be approved, recorded, and tracked so they are replaced by permanent repairs at the first practical opportunity. They are not a substitute for permanent repair.

  88. Question 88Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Buried piping is most commonly inspected at which location?

    1. at the soil-to-air interface Correct answer.
    2. at road crossings only
    3. at the midpoint of the buried run
    4. at the lowest elevation of the run

    Explanation

    The soil-to-air interface is where moisture, oxygen, and stray current conditions change, making it the most corrosion-prone and accessible location for inspecting buried piping. Inspections are concentrated there because the buried length itself is not accessible.

  89. Question 89Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Postweld heat treatment of a repair weld on piping is required when:

    1. the pipe has been in service more than 10 years
    2. the repair is made by a contractor instead of the owner
    3. the repair weld thickness exceeds 1 in (25 mm)
    4. required by the code for the material and thickness Correct answer.

    Explanation

    PWHT requirements follow the applicable code, which bases them on material group, thickness, and service. Neither service age nor who performs the work controls the requirement.

  90. Question 90Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Welding directly onto a piping system that is in service and pressurized is:

    1. permitted if the welder is qualified for the material
    2. prohibited except for approved hot tapping Correct answer.
    3. permitted if the line pressure is below 50% of the MAWP
    4. permitted for small repairs if a hot work permit is issued

    Explanation

    Welding on a live, pressurized line is not permitted because the pressure and fluid can cause burn-through or rupture. Hot tapping under an approved procedure is the recognized exception.

  91. Question 91Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Inspection of an injection point should focus primarily on:

    1. the support nearest the injection point
    2. the injection nozzle and its flange only
    3. the region downstream of the injection point Correct answer.
    4. the upstream piping ten diameters away

    Explanation

    Corrosion at injection points is caused by mixing of the injected stream with the main flow, so the area immediately downstream where mixing occurs is most susceptible. The nozzle and upstream piping are less affected by the mixed condition.

  92. Question 92Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which of the following is the best example of a deadleg that warrants special inspection?

    1. a drain line used during shutdowns
    2. an unused branch connection with no flow Correct answer.
    3. a bypass line with continuous flow
    4. a vent line used daily

    Explanation

    A deadleg is a portion of piping with no continuous flow, allowing corrodents to concentrate or accumulate. An unused branch connection is the classic deadleg and should be included in the inspection program.

  93. Question 93Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Before placing a piping system back in service with a different fluid, the owner/user shall:

    1. review materials and corrosion for the new fluid Correct answer.
    2. replace all gaskets and bolting
    3. hydrotest at twice the design pressure
    4. verify only that the pressure rating is adequate

    Explanation

    A change of service is an alteration with design implications, so the materials, corrosion behavior, and design conditions for the new fluid must be reviewed and documented. Pressure rating alone does not address corrosion or material compatibility.

  94. Question 94Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Repairs and alterations to in-service piping shall be:

    1. documented only when welding is involved
    2. approved by the welder performing the work
    3. approved by the inspector per the owner/user program Correct answer.
    4. performed only by the original fabricator

    Explanation

    The owner/user's quality assurance program governs repairs and alterations, and the inspector approves the work and the repair organization. The welder, and certainly the original fabricator, has no approval authority.

  95. Question 95Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which statement about weld build-up repair of a locally thinned pipe is correct?

    1. It may be used only on stainless steel piping
    2. It requires no examination because the weld is not a pressure boundary
    3. It may be used with qualified procedures and required NDE Correct answer.
    4. It is prohibited on in-service piping

    Explanation

    Weld build-up is an acceptable repair when it is engineered, uses a qualified procedure, and receives the examination and PWHT that the code requires. The deposited weld becomes part of the pressure boundary and must be examined accordingly.

  96. Question 96Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    When a crack is detected in a piping weld, the inspector shall:

    1. coat the area to prevent further cracking
    2. evaluate and repair or assess by engineering Correct answer.
    3. reduce the pressure and continue operating
    4. install a clamp and monitor the crack

    Explanation

    Cracks are planar defects that can grow under cyclic or corrosive conditions, so they must be evaluated and either removed and repaired or assessed by an engineering fitness-for-service analysis. Monitoring alone does not establish acceptability.

  97. Question 97Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which of the following is required before a piping system is rerated to a higher pressure?

    1. An engineering evaluation of all components Correct answer.
    2. Notification of the insurance carrier only
    3. A minimum of ten years of operating history
    4. A new nameplate attached to the pipe

    Explanation

    Rerating changes the pressure or temperature rating, so an engineer must confirm that pipe, fittings, flanges, valves, and supports are adequate for the new conditions. The rerating is then documented and records updated.

  98. Question 98Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    An inspector finds that recent thickness readings indicate accelerated corrosion compared with the long-term trend. Which corrosion rate should normally be used to set the inspection interval?

    1. The average of the long-term and short-term rates
    2. The short-term rate, unless a one-time event Correct answer.
    3. Zero until the acceleration is confirmed
    4. The long-term corrosion rate

    Explanation

    When the recent rate is higher than the historical rate, the higher short-term rate governs because it reflects current conditions. It may be set aside only if the acceleration is explained by an isolated event such as a process upset.

  99. Question 99Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which of the following is a primary purpose of external inspection of piping?

    1. To identify external corrosion and mechanical damage Correct answer.
    2. To measure wall thickness at every fitting and support
    3. To confirm the internal corrosion rate
    4. To verify the set pressure of the relief valve

    Explanation

    External inspection looks for conditions visible from the outside, such as coating breakdown, external corrosion, misalignment, vibration, support problems, and leaks. Thickness measurement and internal rate determination are part of the thickness inspection program.

  100. Question 100Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    For remaining life calculation, the minimum required thickness of a pipe is:

    1. the nominal wall thickness minus mill tolerance
    2. the thickness measured at the last inspection
    3. the original nominal wall thickness
    4. the thickness required by the code for design Correct answer.

    Explanation

    Minimum required thickness is the thickness needed to satisfy the applicable code for the design pressure and temperature. Nominal and previously measured thicknesses describe the metal present, not the metal required.

  101. Question 101Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A pipe measured 0.470 in ten years ago and measures 0.410 in now; its minimum required thickness is 0.280 in. What is the remaining life?

    1. 13.0 years
    2. 21.7 years Correct answer.
    3. 30.0 years
    4. 47.0 years

    Explanation

    The corrosion rate is (0.470 - 0.410) / 10 = 0.006 in/yr, and the remaining margin is 0.410 - 0.280 = 0.130 in. Dividing the margin by the rate gives about 21.7 years.

  102. Question 102Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A thickness reading on a pipe is below the minimum required thickness. What is the appropriate action?

    1. Continue operating until the next turnaround
    2. Increase the inspection frequency and keep operating
    3. Repair, replace, or assess fitness-for-service Correct answer.
    4. Rerate the line to a lower pressure without evaluation

    Explanation

    Metal below the minimum required thickness means the component no longer satisfies the code for its design conditions. It must be repaired, replaced, or shown acceptable by a fitness-for-service assessment before continued operation.

  103. Question 103Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Which of the following is a key requirement before hot tapping a piping system?

    1. Verify wall thickness and use an approved hot tap procedure Correct answer.
    2. Notify the insurance carrier before tapping
    3. Confirm that the line is at its maximum allowable pressure
    4. Ensure the line has been drained and purged

    Explanation

    Hot tapping requires confirmation that the wall is thick enough and that an approved procedure, suitable equipment, and qualified personnel are used. The line must remain in service, so draining and purging is not part of the operation.

  104. Question 104Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    After an alteration changes the design conditions of a piping system, what is required before return to service?

    1. Nothing further if a qualified welder made the joint
    2. Only a visual examination of the altered area
    3. Inspection and testing equivalent to new construction Correct answer.
    4. A new nameplate with the revised rating

    Explanation

    An alteration must be treated like new construction: the work is inspected and tested to the extent required by the code and the inspector, including a pressure test unless it is waived. A qualified welder alone does not complete the quality cycle.

  105. Question 105Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    When the corrosion rate of a piping circuit cannot be established from historical data, the inspector should:

    1. Obtain baseline readings and use a conservative rate Correct answer.
    2. Use the original corrosion allowance as the rate
    3. Assign a fixed ten-year inspection interval
    4. Assume the corrosion rate is zero until metal loss is seen

    Explanation

    Without a rate there is no defensible basis for an interval, so baseline thickness measurements are taken and a conservative assumed rate is applied until sufficient data allow a real rate to be calculated. The assumption is then replaced with measured data.

  106. Question 106Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Welders performing repair welds on in-service piping must be qualified in accordance with which of the following?

    1. The piping fabricator's shop standard
    2. The applicable construction code, such as ASME Section IX Correct answer.
    3. The inspector's own written procedure
    4. The owner/user's purchasing department requirements

    Explanation

    API 570 requires repair welding, including both procedure and welder qualification, to satisfy the applicable construction code, typically ASME B31.3 with welder qualification per ASME Section IX. The inspector confirms that qualification records exist before repair welding begins.

  107. Question 107Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Before a repair organization uses a welding procedure for a repair on in-service piping, the procedure shall be:

    1. Approved by the inspector Correct answer.
    2. Reviewed by the original piping designer
    3. Filed with the jurisdiction having authority
    4. Requalified using the owner/user's welders

    Explanation

    API 570 requires that repair procedures be approved by the inspector before they are used, and that the repair organization qualify procedures and welders to the applicable code. The inspector's approval is part of the quality control of repairs and alterations.

  108. Question 108Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    'Hot bolting' of a piping flange joint is best described as:

    1. Applying heat to a flange to expand the bolts before tightening
    2. Tightening all flange bolts to maximum torque while the line is hot
    3. Replacing a leaking flange gasket while the line is cold
    4. Removing and retightening bolts one at a time while in service Correct answer.

    Explanation

    Hot bolting is the sequential removal, replacement, or retightening of individual flange bolts while the system remains in service. It is done one bolt at a time so that the joint retains adequate seating throughout the operation and requires an approved procedure and risk review.

  109. Question 109Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Lowering the maximum allowable working pressure of an existing piping system, with engineering justification, is an example of:

    1. A repair of the pressure boundary
    2. Abandonment of the system
    3. Rerating of the system Correct answer.
    4. An alteration requiring a pressure test

    Explanation

    Rerating covers any change to the established maximum allowable working pressure or design temperature of an existing system, whether upward or downward. A reduction, often called derating, still requires engineering evaluation, inspector approval, and updated records.

  110. Question 110Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A piping circuit has a calculated remaining life of 12 years. Based on remaining life alone, what is the longest inspection interval permitted by API 570?

    1. 10 years
    2. 6 years Correct answer.
    3. 4 years
    4. 12 years

    Explanation

    The inspection interval may not exceed half of the calculated remaining life, and in no case may it exceed 10 years. Half of 12 years is 6 years, which is also below the 10-year ceiling, so 6 years governs.

  111. Question 111Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    When insulated piping is inspected for corrosion under insulation, attention should be concentrated on:

    1. Only welds that were radiographed at construction
    2. Areas where the insulation is intact and dry
    3. Damaged jacketing, penetrations, and low points Correct answer.
    4. Only the straight runs between fittings

    Explanation

    Corrosion under insulation occurs where water can enter and be held against the steel, which is typically at breaches in the jacketing, at penetrations and terminations, and at low points or other water-collection areas. Intact, dry insulation is the least likely location for attack.

  112. Question 112Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    During an external inspection, the inspector finds a pipe support so badly corroded that the pipe has visibly sagged. What should the inspector do?

    1. Note it in the report for the next scheduled inspection
    2. Reduce the maximum allowable working pressure of the circuit
    3. Report it so the support is restored and the pipe is evaluated Correct answer.
    4. Install a clamp on the pipe at the support

    Explanation

    A failed support can impose unintended loads and stresses on the piping, so it must be corrected and the affected piping assessed for distortion or overstress. Deferring the finding or applying an unrelated repair does not address the loss of support.

  113. Question 113Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Records of repairs and alterations made to in-service piping shall be:

    1. Discarded once the system is returned to service
    2. Maintained by the owner/user for the life of the piping Correct answer.
    3. Kept only until the next inspection is completed
    4. Held solely by the repair contractor

    Explanation

    API 570 requires the owner/user to keep records of inspections, repairs, and alterations for the life of the piping system. These records document the configuration and condition history that later inspections, ratings, and reratings depend on.

  114. Question 114Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A new branch connection is to be added to an existing in-service header. The work is classified as:

    1. A rerating of the header
    2. A temporary repair
    3. Routine maintenance needing no engineering review
    4. An alteration requiring design approval Correct answer.

    Explanation

    Adding a branch connection changes the pressure-containing configuration with design implications, so it is an alteration. Alterations must be engineered and approved, performed by a repair organization, inspected, and documented in the same manner as new construction.

  115. Question 115Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    After a fire occurs in a process unit, what does API 570 call for with respect to nearby piping?

    1. No action, provided the line was not depressurized
    2. Waiting until the next scheduled turnaround
    3. Rerating the piping to a lower pressure
    4. An unscheduled inspection of the affected piping for distortion and damage Correct answer.

    Explanation

    Fire exposure can distort piping, alter metallurgy, and damage supports, so it is treated as a trigger for an unscheduled inspection of the affected systems. The extent of the inspection is set by the inspector based on the exposure.

  116. Question 116Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    When an existing piping system is rerated, which of the following is required?

    1. The identification and rating markings are left as originally installed
    2. The system is hydrotested in every case
    3. The new rating is documented and the records are updated Correct answer.
    4. Only the inspector's verbal concurrence is needed

    Explanation

    Rerating must be supported by engineering evaluation and inspector approval, and the basis for the new rating must be documented with the piping records updated. Marking or other identification is revised so that field personnel know the current rating.

  117. Question 117Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    A corroded elbow is cut out and replaced with a new elbow of the same size, specification, and schedule, welded in accordance with the original code. This work is:

    1. Outside the scope of API 570
    2. A repair that requires inspection and documentation Correct answer.
    3. A rerating of the circuit
    4. An alteration requiring rerating

    Explanation

    Replacement in kind with material of the same specification and schedule restores the existing design rather than changing it, so it is a repair. Repairs must still be made by a repair organization, inspected, and recorded.

  118. Question 118Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Thickness readings at a localized area fall below the calculated minimum required thickness, but a fitness-for-service assessment shows the area is acceptable for continued service. What should the inspector do?

    1. Immediately replace the affected pipe section
    2. Document the assessment and shorten the inspection interval for that area Correct answer.
    3. Rerate the entire circuit to a lower pressure
    4. Take no further action beyond performing the assessment

    Explanation

    API 570 permits continued service of locally thinned areas that are shown acceptable by a fitness-for-service assessment such as API 579, with owner/user approval. The acceptance must be documented and the area monitored more closely through a shortened inspection interval.

  119. Question 119Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Before a piping system is rerated, which of the following must be confirmed?

    1. That the system has operated for at least one year
    2. That the original design drawings are still in the files
    3. That the material, thickness, and supports suit the new conditions Correct answer.
    4. That the piping has never been repaired

    Explanation

    Rerating requires an engineering evaluation showing that the existing materials, measured thicknesses, and support system are adequate for the proposed pressure and temperature. The evaluation is approved by the inspector and documented.

  120. Question 120Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

    Piping that is experiencing severe vibration should be inspected with particular emphasis on:

    1. Small-branch connections, supports, and welds for fatigue cracking Correct answer.
    2. The condition of the external paint system
    3. Thickness loss along long straight runs
    4. Corrosion under insulation at low points

    Explanation

    Vibration fatigue usually initiates at stress concentrations such as small-branch connections, attachment welds, and at supports where restraints or gaps have developed. Inspections therefore target those locations for cracking and looseness rather than general wall loss.

  121. Question 121Inspection Practices, Methods, and Referenced Code Requirements

    During an external inspection of an in-service piping system, which method is performed first and forms the basis for deciding whether additional NDE is required?

    1. Radiographic testing
    2. Positive material identification
    3. Magnetic particle testing
    4. Visual examination Correct answer.

    Explanation

    Visual examination is the primary inspection method for piping and is carried out before and alongside every other NDE technique. It reveals surface condition, corrosion, misalignment, leakage, and insulation damage, and it tells the inspector where targeted NDE should be applied.

  122. Question 122Inspection Practices, Methods, and Referenced Code Requirements

    In API 570 practice, a thickness measurement location (CML) is best described as:

    1. The single thinnest reading ever recorded on a circuit
    2. A marking used only to locate a circuit on an isometric drawing
    3. A point reserved for visual inspection only
    4. A designated point where thickness readings are repeated to trend corrosion Correct answer.

    Explanation

    A CML is a designated location on a piping circuit where thickness measurements are taken repeatedly so that metal loss can be trended and corrosion rates calculated. Readings must be reproducible, so the exact point, orientation, and access are recorded and reused.

  123. Question 123Inspection Practices, Methods, and Referenced Code Requirements

    Which NDE method is appropriate for detecting surface-breaking cracks in an austenitic stainless steel weld?

    1. Liquid penetrant testing Correct answer.
    2. Radiographic testing
    3. Ultrasonic thickness gauging
    4. Magnetic particle testing

    Explanation

    Liquid penetrant testing relies on capillary action to draw penetrant out of surface-breaking discontinuities and works on any non-porous material, including austenitic stainless steel. It is one of the standard methods for surface crack detection in stainless and other non-ferromagnetic welds.

  124. Question 124Inspection Practices, Methods, and Referenced Code Requirements

    Which API document provides detailed descriptions of the damage mechanisms that affect refining and petrochemical fixed equipment?

    1. API 571 Correct answer.
    2. API 577
    3. API 578
    4. API 574

    Explanation

    API 571 is the damage mechanisms reference that describes the appearance, affected materials, critical factors, and inspection techniques for mechanisms such as sulfidation, wet H2S cracking, and CUI. Inspectors use it to link observed damage to its cause.

  125. Question 125Inspection Practices, Methods, and Referenced Code Requirements

    Which inspection method requires a couplant between the search unit and the pipe surface?

    1. Magnetic particle testing
    2. Ultrasonic testing Correct answer.
    3. Radiographic testing
    4. Liquid penetrant testing

    Explanation

    Ultrasonic testing transmits high-frequency sound into the metal, and a couplant such as gel, oil, or glycerin is needed to bridge the air gap between the transducer and the surface. Without it, most of the sound energy is reflected at the interface and no usable signal is obtained.

  126. Question 126Inspection Practices, Methods, and Referenced Code Requirements

    For carbon steel piping, corrosion under insulation is of greatest concern in which metal temperature range?

    1. Approximately 400 °F to 800 °F
    2. Above 900 °F
    3. Below 0 °F
    4. Approximately 10 °F to 350 °F Correct answer.

    Explanation

    Carbon steel CUI occurs where water can be present in the insulation and the metal temperature is roughly 10 °F to 350 °F. Within that window moisture is liquid at the surface often enough to support corrosion, while above the upper limit the surface generally dries out.

  127. Question 127Inspection Practices, Methods, and Referenced Code Requirements

    Which API document describes a material verification program for new and existing alloy piping systems?

    1. API 578 Correct answer.
    2. API 580
    3. API 574
    4. API 570

    Explanation

    API 578 provides the framework for verifying that the alloy installed or already in service matches the specified material, using techniques such as X-ray fluorescence and optical emission spectroscopy. It also addresses sampling extent and record keeping.

  128. Question 128Inspection Practices, Methods, and Referenced Code Requirements

    Inspection of buried piping at the soil-to-air interface concentrates on:

    1. Cathodic protection rectifier connections
    2. Deep undisturbed soil well below grade
    3. The internal surface at each support point
    4. The region just above and below the ground surface Correct answer.

    Explanation

    The soil-to-air interface is a transition zone where oxygen concentration differs, moisture cycles occur, and coatings are most often damaged by backfill and traffic. Corrosion rates there are typically much higher than in fully buried or fully exposed sections, so it is a priority inspection area.

  129. Question 129Inspection Practices, Methods, and Referenced Code Requirements

    A CML on a carbon steel line reads 0.520 in. The minimum required thickness is 0.400 in., and the long-term corrosion rate is 0.015 in./yr. What is the remaining life?

    1. 5 years
    2. 8 years Correct answer.
    3. 3 years
    4. 10 years

    Explanation

    Remaining life equals the corrosion allowance remaining divided by the corrosion rate: (0.520 − 0.400) / 0.015 = 0.120 / 0.015 = 8 years. This value then drives the maximum permitted inspection interval.

  130. Question 130Inspection Practices, Methods, and Referenced Code Requirements

    At a CML, the wall thickness measured 0.625 in. in 2016 and 0.545 in. in 2024. What is the average corrosion rate?

    1. 0.010 in./yr Correct answer.
    2. 0.005 in./yr
    3. 0.080 in./yr
    4. 0.008 in./yr

    Explanation

    The metal loss is 0.625 − 0.545 = 0.080 in. over 8 years, giving 0.080 / 8 = 0.010 in./yr. The rate is computed from the difference between readings divided by the elapsed time between them.

  131. Question 131Inspection Practices, Methods, and Referenced Code Requirements

    A CML shows a long-term corrosion rate of 0.003 in./yr, but the last two inspection intervals show 0.012 in./yr. Which rate should govern the remaining-life calculation?

    1. No rate until a second CML confirms the result
    2. The long-term rate, because averaging removes measurement error
    3. The recent higher rate, because it shows accelerated metal loss Correct answer.
    4. The long-term rate, because API 570 requires its use

    Explanation

    When recent short-term data show a rate significantly above the long-term trend, the increase signals that the damage has accelerated and the long-term average no longer represents current conditions. Remaining life must then be based on the higher short-term rate so the interval is not set optimistically.

  132. Question 132Inspection Practices, Methods, and Referenced Code Requirements

    Magnetic particle testing can be applied only to:

    1. Ferromagnetic materials Correct answer.
    2. Austenitic stainless steels
    3. Aluminum and copper alloys
    4. Any non-porous material

    Explanation

    Magnetic particle testing depends on the material being magnetizable so that flux leakage occurs at a discontinuity and attracts the particles. Carbon steels and most low-alloy steels are suitable; austenitic stainless steels and non-ferrous alloys are not.

  133. Question 133Inspection Practices, Methods, and Referenced Code Requirements

    Which capability is associated with radiography but not with liquid penetrant testing?

    1. Detection of surface-breaking discontinuities
    2. Detection of internal volumetric discontinuities Correct answer.
    3. Use without access for a detector
    4. Use without any radiation safety controls

    Explanation

    Radiography transmits radiation through the component and records density differences, so it detects internal volumetric defects such as porosity and slag inclusions. Penetrant testing is restricted to discontinuities that are open to the surface.

  134. Question 134Inspection Practices, Methods, and Referenced Code Requirements

    Welding procedures and welders used to repair in-service piping must be qualified in accordance with:

    1. ASME BPVC Section IX Correct answer.
    2. API 577 Appendix A
    3. API 1104 in all cases
    4. ASME B31.3 Section VI alone

    Explanation

    ASME B31.3 requires welding procedure specifications and performance qualification of welders and operators in accordance with Section IX of the ASME Boiler and Pressure Vessel Code. API 570 carries this requirement forward for repairs and alterations made to in-service piping.

  135. Question 135Inspection Practices, Methods, and Referenced Code Requirements

    Under ASME B31.3, the minimum hydrostatic test pressure for a piping system is:

    1. 1.5 times the design pressure Correct answer.
    2. 1.1 times the design pressure
    3. 2.0 times the design pressure
    4. 1.25 times the design pressure

    Explanation

    B31.3 sets the hydrostatic test at 1.5 times the design pressure, adjusted for the ratio of allowable stresses at test and design temperature. The same basis is applied by API 570 when a hydrostatic test is required after a repair or alteration.

  136. Question 136Inspection Practices, Methods, and Referenced Code Requirements

    When a pneumatic test is used instead of a hydrostatic test under ASME B31.3, the minimum test pressure is:

    1. 1.1 times the design pressure Correct answer.
    2. 1.0 times the design pressure
    3. 1.25 times the design pressure
    4. 1.5 times the design pressure

    Explanation

    Because of the stored energy hazard, B31.3 permits a pneumatic test at a lower pressure than a hydrostatic test, specifically 1.1 times the design pressure, with additional precautions such as remote observation and progressive pressurization.

  137. Question 137Inspection Practices, Methods, and Referenced Code Requirements

    A short, capped branch that is normally isolated from the main flow is best described as:

    1. An injection point
    2. A designated CML
    3. An approved temporary repair
    4. A deadleg that warrants periodic inspection Correct answer.

    Explanation

    An isolated, stagnant branch is a deadleg, where corrosion can concentrate because of stagnant conditions, concentration of corrodents, or accumulation of water and sediment. Deadlegs are routinely flagged for periodic thickness measurement or removal.

  138. Question 138Inspection Practices, Methods, and Referenced Code Requirements

    API 570 draws special attention to injection points because of localized corrosion near the injection nozzle. A practice consistent with that guidance is:

    1. Reducing CML coverage around the injection region
    2. Applying shorter intervals than the rest of the circuit Correct answer.
    3. Excluding the injection nozzle from the circuit isometric
    4. Using the same interval as the rest of the circuit

    Explanation

    Injection points often experience accelerated or localized attack from the injected stream, so API 570 expects them to be inspected more often than the rest of the circuit, with dedicated corrosion monitoring where appropriate.

  139. Question 139Inspection Practices, Methods, and Referenced Code Requirements

    Portable hardness testing on a piping weld is most commonly performed to:

    1. Determine the remaining corrosion allowance
    2. Detect internal lack of fusion
    3. Measure wall thickness at the weld
    4. Verify that a specified hardness limit has been met Correct answer.

    Explanation

    Hardness checks after welding, particularly after post-weld heat treatment or on high-strength or hardenable materials, confirm that the specified hardness limit is satisfied. Hardness is a screening indicator for susceptibility to cracking and for adequate heat treatment.

  140. Question 140Inspection Practices, Methods, and Referenced Code Requirements

    A piping circuit has a remaining life of 12 years. What is the maximum inspection interval permitted by API 570?

    1. 10 years
    2. 12 years
    3. 8 years
    4. 6 years Correct answer.

    Explanation

    API 570 caps the inspection interval at half of the calculated remaining life, so a 12-year remaining life gives a maximum interval of 6 years. The interval may be shorter if the class of service or other considerations require it.

  141. Question 141Inspection Practices, Methods, and Referenced Code Requirements

    A localized area of a piping circuit measures below the minimum required thickness. Which document is used to assess whether it may remain in service until the next shutdown?

    1. API 580
    2. API 579-1/ASME FFS-1 Correct answer.
    3. API 574
    4. API 571

    Explanation

    API 579-1/ASME FFS-1 provides fitness-for-service assessment procedures that determine whether a locally thinned or flawed component can continue to operate safely until repair or replacement. API 570 directs the inspector to that document when a component falls below the design minimum.

  142. Question 142Inspection Practices, Methods, and Referenced Code Requirements

    Which portion of an insulated piping system is most likely to suffer corrosion under insulation?

    1. Sections where the insulation is completely removed
    2. Low points, penetrations, and damaged jacketing Correct answer.
    3. Piping operating continuously above 1000 °F
    4. Vertical runs with intact, well-sealed jacketing

    Explanation

    CUI requires a water path into the insulation, and that path most often exists at low points, penetrations, terminations, and damaged or unsealed jacketing. These are therefore where insulation is stripped for inspection.

  143. Question 143Inspection Practices, Methods, and Referenced Code Requirements

    A close-interval pipe-to-soil potential survey on a buried coated line is primarily used to:

    1. Determine the internal corrosion rate
    2. Measure remaining wall thickness through the coating
    3. Locate coating damage and weak cathodic protection Correct answer.
    4. Identify the grade of the pipe steel

    Explanation

    Close-interval surveys read pipe-to-soil potentials at frequent spacing along the line, revealing holidays in the coating and areas where cathodic protection is inadequate. Excavations for direct examination are then targeted at those locations.

  144. Question 144Inspection Practices, Methods, and Referenced Code Requirements

    When measuring wall thickness of austenitic stainless steel piping ultrasonically, which practice improves reliability?

    1. Reading only the digital display with no reference standard
    2. Using the highest available frequency with a single-crystal probe
    3. Using a dual-crystal probe standardized on the same alloy Correct answer.
    4. Assuming carbon steel sound velocity applies

    Explanation

    Coarse grain structure in austenitic stainless steel scatters and attenuates sound, producing noise and erratic readings. A dual-crystal probe at a suitable frequency, calibrated on a reference block of the same alloy, compensates for the different sound velocity and improves repeatability.

  145. Question 145Inspection Practices, Methods, and Referenced Code Requirements

    Which application is best suited to guided wave ultrasonic testing of piping?

    1. Hardness measurement in a weld heat-affected zone
    2. Rapid screening for metal loss along long coated or buried runs Correct answer.
    3. Surface crack detection in a small forged fitting
    4. Point wall thickness measurement to 0.001 in.

    Explanation

    Guided wave testing propagates an ultrasonic wave along the pipe wall over tens of feet from a single collar location, making it a screening tool for metal loss under coatings, at supports, and in buried or inaccessible sections. Indications are then confirmed by conventional thickness measurement.

  146. Question 146Inspection Practices, Methods, and Referenced Code Requirements

    Who is responsible for establishing the inspection intervals for piping circuits in an operating process plant?

    1. The inspection contractor performing the UT survey
    2. The owner/user with input from the inspector Correct answer.
    3. The jurisdiction's chief inspector
    4. The authorized inspector acting alone

    Explanation

    API 570 places the responsibility for the piping inspection program, including the setting of inspection intervals, on the owner/user. The inspector supplies condition data, corrosion rates, and recommendations, but the owner/user approves and documents the intervals.

  147. Question 147Inspection Practices, Methods, and Referenced Code Requirements

    During a visual inspection of an operating piping system, which condition at a pipe support deserves priority attention?

    1. The specified length of the hanger rod
    2. A missing identification tag on the support steel
    3. Faded paint on the support steel
    4. Corrosion where the pipe rests on the support Correct answer.

    Explanation

    Pipe supports form crevices and contact points where moisture, dirt, and debris collect, so external corrosion and mechanical damage at the pipe-to-support interface are a primary integrity concern. Cosmetic and administrative deficiencies do not threaten containment.

  148. Question 148Inspection Practices, Methods, and Referenced Code Requirements

    A holiday test performed on the coating of a buried pipe is used to:

    1. Determine the electrical resistivity of the soil
    2. Verify the output current of the cathodic protection system
    3. Detect discontinuities and pinholes in the coating Correct answer.
    4. Measure the dry film thickness of the coating

    Explanation

    A holiday detector applies a voltage across the coating and signals when current passes through a break, revealing pinholes and other discontinuities that would admit electrolyte. Detecting these defects is essential because coating damage concentrates external corrosion on buried pipe.

  149. Question 149Inspection Practices, Methods, and Referenced Code Requirements

    The wall thickness of a hot, insulated line must be assessed without removing the insulation. Which method is best suited?

    1. Magnetic particle testing
    2. Liquid penetrant testing
    3. Profile radiography Correct answer.
    4. Contact ultrasonic testing from a bare metal surface

    Explanation

    Profile radiography places a source and detector on opposite sides of the insulated pipe so the radiation passes through the insulation and reveals the pipe walls, allowing thickness and internal deposits to be judged. The surface NDE methods and contact UT all require direct access to the bare metal.

  150. Question 150Inspection Practices, Methods, and Referenced Code Requirements

    Which technique is used in the field for positive material identification of alloy piping?

    1. Hydrostatic leak testing of the spool
    2. Magnetic particle testing of the weld
    3. Ultrasonic thickness measurement at a CML
    4. Portable X-ray fluorescence spectrometry Correct answer.

    Explanation

    Portable X-ray fluorescence analyzers excite the metal and read the characteristic X-rays emitted, identifying the alloying elements present so the material can be verified against the specification. The other methods evaluate tightness, surface defects, or thickness, not chemical composition.

  151. Question 151Inspection Practices, Methods, and Referenced Code Requirements

    When selecting condition monitoring locations for a piping circuit, the inspector should place them:

    1. At locations susceptible to the expected damage mechanism Correct answer.
    2. Where scaffolding is cheapest to erect
    3. At equal spacing along straight runs, without regard to damage mechanism
    4. Only on fittings, because straight pipe does not corrode

    Explanation

    CMLs must represent the damage expected in the circuit, so they are positioned where turbulence, phase change, low points, and similar drivers make metal loss most likely. Spacing based on convenience or uniform geometry alone can leave the worst location unmonitored.

  152. Question 152Inspection Practices, Methods, and Referenced Code Requirements

    Welding or hot tapping on piping that remains in service should follow the guidance of which document?

    1. NACE SP0169
    2. API 2201 Correct answer.
    3. API 579-1/ASME FFS-1
    4. API 580

    Explanation

    API 2201 provides procedures for welding or hot tapping on equipment in service, addressing burn-through risk, minimum wall thickness, and safe welding practice on a live line. The other documents cover fitness-for-service, risk-based inspection, and external corrosion control.

  153. Question 153Inspection Practices, Methods, and Referenced Code Requirements

    At a condition monitoring location, the thickness entered into the inspection record should be:

    1. The lowest reading found in the scanned area Correct answer.
    2. The average of all readings taken at the location
    3. The highest reading obtained in the scan
    4. The reading taken at the top of the pipe

    Explanation

    The recorded value must reflect the worst condition found within the scanned area, because localized thinning governs remaining life and the required fitness-for-service evaluation. Averaging or selecting a favorable reading would overstate the thickness available for continued service.

  154. Question 154Inspection Practices, Methods, and Referenced Code Requirements

    Piping that is subject to vibration is best inspected by concentrating on:

    1. The thickness of the insulation and jacketing
    2. Small-bore branch connections and their welds Correct answer.
    3. The condition of the flange face finish
    4. The internal bore of the main line for pitting corrosion

    Explanation

    Vibration fatigue in piping typically initiates at small-bore branch connections, unsupported spans, and attachment welds where alternating stresses concentrate. Inspectors look for cracked or broken welds, fretting, and loose or failed supports in these areas.

  155. Question 155Inspection Practices, Methods, and Referenced Code Requirements

    Under ASME B31.3, the hydrostatic test pressure on a piping system shall be held for a minimum of:

    1. 2 hours
    2. 10 minutes Correct answer.
    3. 1 minute
    4. 30 minutes

    Explanation

    ASME B31.3 requires the hydrostatic test pressure to be held for at least 10 minutes before the system is examined for leaks. The hold allows the system to stabilize so that small leaks and joint defects become evident.

  156. Question 156Inspection Practices, Methods, and Referenced Code Requirements

    Before a hydrostatic test is applied to a piping system, which items should be removed or isolated?

    1. The corrosion coupons installed in the line
    2. All pipe hangers and supports in the system
    3. Pressure relief valves and instruments not rated for the test Correct answer.
    4. Every flange gasket in the system

    Explanation

    Components that cannot withstand the test pressure, such as pressure relief valves, rupture discs, and certain instruments, must be removed, blinded, or otherwise isolated before testing. Supports remain in service and are checked for movement while the system is pressurized.

  157. Question 157Inspection Practices, Methods, and Referenced Code Requirements

    An electrical resistance corrosion probe installed in a process line is used to:

    1. Measure pipe-to-soil potential
    2. Measure wall thickness over a large area of pipe
    3. Show short-term changes in corrosion rate Correct answer.
    4. Detect subsurface weld defects

    Explanation

    An electrical resistance probe measures the increase in resistance of a thin exposed element as it loses metal, giving a rapid indication of the current corrosion rate in the process stream. Its response is local to the probe element and is not a substitute for a wall thickness survey of the pipe.

  158. Question 158Inspection Practices, Methods, and Referenced Code Requirements

    A piping circuit operates above the temperature at which creep becomes significant. Which inspection activity is specifically important for this circuit?

    1. Wet fluorescent magnetic particle testing of every weld
    2. Annual hydrostatic testing of the circuit
    3. Holiday testing of the insulation jacketing
    4. Measurement of diametral growth, sag, and support movement Correct answer.

    Explanation

    At elevated temperature the metal can deform permanently with time, so inspections include dimensional checks for diameter growth, sag, and displacement or binding of supports and spring hangers. These measurements track creep deformation that thickness readings alone would not reveal.

  159. Question 159Inspection Practices, Methods, and Referenced Code Requirements

    In a line carrying a high-velocity abrasive slurry, thinning of a 90-degree elbow is most likely to be found:

    1. In the straight run upstream of the bend
    2. At the extrados of the bend and just downstream Correct answer.
    3. On the intrados of the bend
    4. Uniformly around the whole circumference of the bend

    Explanation

    In abrasive service the particles are thrown outward as the flow changes direction, so the outer radius of the bend and the pipe immediately downstream receive the greatest impact and thin first. Inspectors therefore concentrate readings on the extrados rather than the inside radius.

  160. Question 160Inspection Practices, Methods, and Referenced Code Requirements

    A piping circuit contains several condition monitoring locations whose calculated remaining lives range from 4 to 22 years. The inspection interval for the whole circuit is established from:

    1. The design life stated for the plant
    2. The CML with the shortest remaining life Correct answer.
    3. The average remaining life of all CMLs
    4. The CML with the longest remaining life

    Explanation

    The circuit's remaining life is governed by the location with the highest corrosion rate and shortest remaining life, so the inspection interval is derived from that worst-case location. Using an average or the healthiest location would leave the limiting point without timely inspection.

  161. Question 161Records, Reports, and Repair/Replacement Documentation

    Work on a pressure-retaining piping repair shall not begin until the repair procedure is approved by the:

    1. repair organization's shop foreman
    2. operations supervisor
    3. maintenance planner
    4. authorized inspector Correct answer.

    Explanation

    The inspector reviews and approves repair procedures before repair work starts, so that the chosen method restores integrity and complies with the applicable code and the owner/user's requirements.

  162. Question 162Records, Reports, and Repair/Replacement Documentation

    As a minimum, an inspection record for a piping system shall include the:

    1. process fluid vendor, unit number, and pump curve
    2. purchase order number, labor hours, and contractor name
    3. welder identification, heat number, and preheat
    4. date, inspector, type, results, and recommendations Correct answer.

    Explanation

    The record of each inspection must identify when the inspection was done, who did it, what kind of inspection it was, what was found, and what action is recommended so the results can be acted upon later.

  163. Question 163Records, Reports, and Repair/Replacement Documentation

    A repair organization that welds on pressure-retaining piping shall hold:

    1. a national board registration covering the piping system
    2. an API 570 certification issued for each of its welders
    3. a valid ASME Certificate of Authorization with the applicable code symbol stamp Correct answer.
    4. an ISO 9001 quality system certificate issued for its fabrication shop and field crews

    Explanation

    Pressure-containing repairs must be performed by an organization qualified under the ASME code system, that is, one holding a valid Certificate of Authorization for the applicable code symbol stamp for the work being done.

  164. Question 164Records, Reports, and Repair/Replacement Documentation

    Welding procedures used for repairs to pressure-retaining piping shall be qualified in accordance with:

    1. API Recommended Practice 1104
    2. the repair organization's internal welding standard
    3. ASME BPVC Section VIII, Division 1
    4. ASME BPVC Section IX Correct answer.

    Explanation

    Welding procedure specifications, and the procedure qualification records that support them, must be qualified to ASME BPVC Section IX, which governs welding qualification for these repairs.

  165. Question 165Records, Reports, and Repair/Replacement Documentation

    The inspection, repair, and alteration records for an in-service piping system shall be maintained by the:

    1. authorized inspection agency that performed the inspections
    2. repair organization that made the most recent repair
    3. jurisdiction in which the plant is located
    4. owner/user Correct answer.

    Explanation

    The owner/user is responsible for the integrity of the piping system and therefore owns the obligation to keep the inspection, repair, and alteration records, regardless of who performed the work.

  166. Question 166Records, Reports, and Repair/Replacement Documentation

    Inspection and repair records for a piping system shall be retained by the owner/user for:

    1. as long as the responsible inspector remains employed
    2. three years after the last repair
    3. the life of the piping system Correct answer.
    4. one complete inspection interval

    Explanation

    The records must remain available for the entire service life of the piping system, because corrosion-rate, remaining-life, and repair history decisions depend on the full record.

  167. Question 167Records, Reports, and Repair/Replacement Documentation

    The record of a completed piping repair shall include the:

    1. materials used, NDE performed, and identification of the repair organization Correct answer.
    2. shipping weight of the replacement components received
    3. hourly rate and overtime hours charged by the repair organization
    4. ambient weather conditions during the performance of the work

    Explanation

    A repair record has to show what was done, with what materials, how it was examined, and who did the work, so that a later reviewer can judge the adequacy of the repair.

  168. Question 168Records, Reports, and Repair/Replacement Documentation

    The inspector's report of a piping inspection should state the:

    1. remaining life and the date for the next inspection Correct answer.
    2. number of maintenance employees assigned to the unit
    3. name of the process licensor and the plant design capacity
    4. cost of the inspection and the responsible budget code

    Explanation

    The report communicates findings and drives future work, so it must state the assessed condition, including remaining life and when the next inspection is due.

  169. Question 169Records, Reports, and Repair/Replacement Documentation

    Re-rating of a piping system requires the approval of the:

    1. inspector alone
    2. piping engineer and the inspector Correct answer.
    3. repair organization and the jurisdiction
    4. piping engineer alone

    Explanation

    Re-rating changes the design basis of the system, so it needs engineering approval of the new rating as well as the inspector's concurrence that the condition of the piping supports that rating.

  170. Question 170Records, Reports, and Repair/Replacement Documentation

    Responsibility for the engineering design of an alteration to a piping system rests with the:

    1. authorized inspector
    2. repair organization's welder
    3. piping engineer Correct answer.
    4. owner's maintenance planner

    Explanation

    An alteration changes the design basis, so it must be designed and approved by the piping engineer; the inspector then verifies that the work is executed and documented as designed.

  171. Question 171Records, Reports, and Repair/Replacement Documentation

    A temporary repair is installed on a corroded elbow so the unit can keep running until the next shutdown. The temporary repair shall be:

    1. removed within 24 hours of installation regardless of the unit's operating status
    2. left out of the records because it is not a permanent change to the system
    3. reclassified as an alteration after it has been in service for 6 months
    4. recorded and replaced with a permanent repair at the next opportunity Correct answer.

    Explanation

    Temporary repairs are permitted only as a short-term measure; they must be documented in the records and converted to a permanent repair at the next available opportunity.

  172. Question 172Records, Reports, and Repair/Replacement Documentation

    A hot tap made on an in-service piping system is acceptable when the:

    1. tap is small enough that no record of the work is required
    2. procedure is approved and the tap is documented as a repair Correct answer.
    3. line carries water and operates below 100 degF (38 degC)
    4. work is performed by operations personnel on the night shift

    Explanation

    Hot tapping is a specialized operation that requires an approved procedure and engineering and inspector review, and it must be documented in the repair records like any other repair.

  173. Question 173Records, Reports, and Repair/Replacement Documentation

    After an approved alteration has been completed, which records shall be updated to reflect the change?

    1. only the inspector's field notes
    2. no records, provided the work was inspected
    3. only the repair organization's welding log
    4. the affected drawings and piping documentation Correct answer.

    Explanation

    Alterations change the system, so the drawings and piping documentation that describe it must be brought to as-built status and retained with the system records.

  174. Question 174Records, Reports, and Repair/Replacement Documentation

    Evidence that a welder is qualified to make a repair weld on carbon steel piping is provided by the:

    1. weld map on the piping isometric
    2. welder performance qualification record Correct answer.
    3. welder's employment application
    4. purchase order for the welding electrodes

    Explanation

    A welder performance qualification record, established under the welding code and supported by continuity records, documents that the individual is qualified for the specific variables of the repair weld.

  175. Question 175Records, Reports, and Repair/Replacement Documentation

    After radiographic examination of a repair weld, the repair record shall include the:

    1. travel and subsistence costs of the radiographer
    2. ambient light level measured in the darkroom
    3. extent of examination performed and the results obtained Correct answer.
    4. name of the film supplier and the film lot number

    Explanation

    The record must show how much of the repair was examined and what the examination found, so that acceptance of the repair can be verified later.

  176. Question 176Records, Reports, and Repair/Replacement Documentation

    A corroded spool is replaced with a new spool of the same material, size, and schedule, restoring the original design. In the records this work is classified as a:

    1. new construction
    2. re-rating
    3. repair Correct answer.
    4. alteration

    Explanation

    Restoring a component to its original design condition with like-for-like material is a repair; an alteration would change the design parameters or piping class.

  177. Question 177Records, Reports, and Repair/Replacement Documentation

    A weld repair requires postweld heat treatment. The repair record shall include the:

    1. cost of the fuel consumed during heat treatment
    2. time and temperature chart for the heat treatment Correct answer.
    3. name of the operator who lit the furnace burner
    4. brand name of the furnace used for the treatment

    Explanation

    Heat treatment is a quality-critical variable, so the record must contain the time and temperature data that demonstrate the specified treatment was achieved.

  178. Question 178Records, Reports, and Repair/Replacement Documentation

    The inspection records for a piping system shall include the:

    1. market price of the piping alloy at the time of purchase
    2. number of utility stations installed in the unit
    3. salary grade of the inspector who performed the work
    4. corrosion rate and remaining life calculated for the piping Correct answer.

    Explanation

    Corrosion rate and remaining life are the technical outputs used to set inspection intervals, so they must be recorded and kept current in the inspection records.

  179. Question 179Records, Reports, and Repair/Replacement Documentation

    A repaired piping system is pressure tested before return to service. The records shall include the:

    1. manufacturer of the pressure gauge dial face
    2. test medium, test pressure, and test duration Correct answer.
    3. number of workers present during the test
    4. weather forecast issued for the day of the test

    Explanation

    The test record must state what the system was tested with, at what pressure, and for how long, because those are the parameters that establish the validity of the test.

  180. Question 180Records, Reports, and Repair/Replacement Documentation

    During a records review, an inspector finds a repair record that does not identify the welding procedure or the welder. The appropriate action is to:

    1. require the repair organization to supply the missing information Correct answer.
    2. accept the record because the weld passed visual examination
    3. sign the record and inform the repair organization verbally
    4. discard the record and schedule a new repair of the same joint

    Explanation

    A repair record is not complete until it identifies the qualified procedure and the qualified welder; the deficiency must be resolved by obtaining the missing information before the record is accepted.

  181. Question 181Records, Reports, and Repair/Replacement Documentation

    The owner/user intends to change the service of an existing piping system to a more corrosive fluid. Before the change is made, the owner/user shall:

    1. have the change evaluated and documented, including any required re-rating Correct answer.
    2. install a temporary repair clamp and continue operating the system
    3. take no action, because the piping class and design pressure do not change
    4. notify the repair organization that the process fluid has changed

    Explanation

    A service change alters the corrosion environment and can change the allowable limits, so it must be evaluated by engineering, with the inspector's concurrence, and the outcome must be recorded.

  182. Question 182Records, Reports, and Repair/Replacement Documentation

    Repairs made by the owner/user's own maintenance organization instead of a contractor are:

    1. recorded only if a certified welder performs the work
    2. subject to the same documentation and approval requirements Correct answer.
    3. exempt from record keeping because the work is internal
    4. recorded only when the repair cost exceeds a set threshold

    Explanation

    The rules apply to the work, not to who performs it, so in-house forces must follow the same approval, examination, and record keeping requirements as an outside repair organization.

  183. Question 183Records, Reports, and Repair/Replacement Documentation

    Non-destructive examinations performed as part of a piping repair shall be conducted by:

    1. personnel trained only by the repair organization's safety officer
    2. personnel qualified under a recognized NDE qualification program Correct answer.
    3. the inspector, who is qualified in every NDE method by certification
    4. any welder who made the repair weld on the component

    Explanation

    Examinations must be performed by personnel qualified and certified in the specific method under a recognized NDE qualification program, and those qualification records are retained.

  184. Question 184Records, Reports, and Repair/Replacement Documentation

    The primary purpose of a complete and permanent repair record for a piping system is to:

    1. document the repair organization's profit margin on the work
    2. let future inspectors evaluate the repair and plan later inspections Correct answer.
    3. satisfy the invoicing requirements of the repair organization
    4. provide the welder with evidence for a pay increase

    Explanation

    The record preserves the technical history of the repair so that inspectors who were not present can judge its adequacy and set inspection intervals accordingly.

  185. Question 185Records, Reports, and Repair/Replacement Documentation

    The record of an alteration to a piping system shall include the:

    1. shipping manifest for the replacement components
    2. operator's log of process changes made during the work
    3. supplier's certificate for the welding electrodes only
    4. design calculations, drawings, and the engineer's approval Correct answer.

    Explanation

    An alteration is defined by a change in design basis, so the record must contain the engineering basis for the change together with the drawings and the engineer's approval.

  186. Question 186Records, Reports, and Repair/Replacement Documentation

    Before inspecting a piping system, the inspector should review which of the following?

    1. The prior inspection, repair, and alteration records Correct answer.
    2. The original purchase orders for the pipe and fittings
    3. The manufacturer's current product catalog for the pipe
    4. The unit's operating budget for the coming year

    Explanation

    The inspector is expected to become familiar with the system's history before the inspection so that previously found problems, repairs, and alterations are considered when planning the work. The prior records are the baseline against which new findings are judged.

  187. Question 187Records, Reports, and Repair/Replacement Documentation

    Documentation of a completed repair, including welding, examination, and testing records, must be furnished to the owner/user by:

    1. The jurisdiction's chief boiler inspector
    2. The inspector assigned to the system
    3. The insurer of the piping system
    4. The repair organization that did the work Correct answer.

    Explanation

    The organization that performs a repair is responsible for the quality of that work and must provide the owner/user with the records that document it. The owner/user then keeps these records with the system file.

  188. Question 188Records, Reports, and Repair/Replacement Documentation

    Inspection and repair records for a piping system shall be made available to:

    1. Only the jurisdiction's insurance carrier
    2. The authorized inspector of the piping system Correct answer.
    3. Only the owner/user's senior management
    4. Any outside contractor who requests a copy

    Explanation

    The owner/user maintains the records, and they must be accessible to the authorized inspector so that the system's condition, repairs, and history can be evaluated. Access is not limited to management or to third parties.

  189. Question 189Records, Reports, and Repair/Replacement Documentation

    Each inspection and repair record shall identify the piping system by:

    1. Its thermal insulation specification
    2. The date the pipe was last painted
    3. The name of the operator on duty
    4. Its unique line or system number Correct answer.

    Explanation

    A record is only useful if it can be filed against and retrieved for the correct system, so each record must carry the unique line or system identification. This traceability links the record to the system's design and inspection history.

  190. Question 190Records, Reports, and Repair/Replacement Documentation

    A temporary repair is installed to keep a line running. The record of that temporary repair should include:

    1. The name of the contractor's purchasing agent
    2. The date it must be removed or re-evaluated Correct answer.
    3. The labor hours charged against the work order
    4. The ambient temperature when it was installed

    Explanation

    A temporary repair is a short-term measure with a defined allowable service period. The record must show when it was installed and when it must be removed or re-evaluated so it is not left in place indefinitely.

  191. Question 191Records, Reports, and Repair/Replacement Documentation

    A piping component fails in service and is replaced. The records for the system should include:

    1. The catalog number of the replacement part
    2. The results of the failure analysis Correct answer.
    3. The salvage value received for the failed part
    4. The overtime hours paid to the maintenance crew

    Explanation

    When a component fails, the cause must be established and the findings retained so the inspection plan can be adjusted and the failure avoided in the future. The failure analysis is part of the system's permanent record.

  192. Question 192Records, Reports, and Repair/Replacement Documentation

    The inspection plan developed through a risk-based inspection assessment shall be:

    1. Retained only until the next scheduled turnaround
    2. Kept only by the inspector who performed the assessment
    3. Documented, with the basis for the plan Correct answer.
    4. Communicated verbally to the operators on shift

    Explanation

    Risk-based inspection produces a documented plan, and the assessment, the plan, and the reasoning behind the planned activities must be recorded. Documentation allows the program to be audited and revised as operating conditions change.

  193. Question 193Records, Reports, and Repair/Replacement Documentation

    Records that show the NDE personnel who examined a repair weld were qualified shall be maintained by:

    1. The jurisdiction that regulates the plant
    2. The employer of the NDE personnel Correct answer.
    3. The authorized inspector who ordered the NDE
    4. The owner/user's training department

    Explanation

    Certification of NDE personnel is administered by their employer under the applicable qualification program, so the employer holds the certification and qualification records and must produce them when the repair is reviewed.

  194. Question 194Records, Reports, and Repair/Replacement Documentation

    Before a repaired piping system is returned to service, the inspector should verify that:

    1. The replacement components have been painted
    2. The repair records are complete and acceptable Correct answer.
    3. The operators have been briefed on the repair
    4. The repair organization has submitted its invoice

    Explanation

    Return to service is a hold point at which the inspector confirms that the repair was completed to the applicable requirements and that all required documentation is in hand. Incomplete records mean the repair cannot be accepted.

  195. Question 195Records, Reports, and Repair/Replacement Documentation

    The basis for the inspection interval selected for a piping system shall be:

    1. Documented and retained with the system records Correct answer.
    2. Recorded only on the next inspection work order
    3. Held by the inspector in personal notes
    4. Agreed verbally between the inspector and the operator

    Explanation

    The interval and the reasoning behind it are part of the inspection record. A documented basis lets the owner/user and later inspectors understand and justify the interval when conditions or results change.

  196. Question 196Records, Reports, and Repair/Replacement Documentation

    Repair history for a piping system is most useful to the inspector for:

    1. Confirming the condition of the external coating
    2. Identifying repeat problems and planning inspections Correct answer.
    3. Scheduling the plant's preventive maintenance budget
    4. Verifying the repair contractor's invoiced labor rates

    Explanation

    Repair history reveals patterns such as repeated failures at the same location or a change in damage behavior, which feed directly into the inspection plan and interval selection. It is a technical tool, not a cost record.

  197. Question 197Records, Reports, and Repair/Replacement Documentation

    The location of each condition monitoring location (CML) shall be:

    1. Recorded in the inspector's field notebook
    2. Documented so readings can be repeated Correct answer.
    3. Marked on the pipe only with chalk during each inspection
    4. Listed only in the inspection contractor's report

    Explanation

    Thickness readings are only useful for trending if successive readings are taken at the same place. Each CML must therefore be located and documented so that it can be found and re-measured on later inspections.

  198. Question 198Records, Reports, and Repair/Replacement Documentation

    During a records review, an inspector finds an installed alteration that is not shown on the P&IDs or isometric drawings. The inspector should:

    1. Accept the alteration since it has already been inspected
    2. Require the drawings and records to be updated Correct answer.
    3. Note the discrepancy in the next inspection report only
    4. Remove the alteration and restore the original piping

    Explanation

    Records must reflect the actual installed configuration, so drawings and records that do not show an installed alteration are deficient and must be corrected. Accurate records are the basis for all future inspections and engineering evaluations.

  199. Question 199Records, Reports, and Repair/Replacement Documentation

    A piping system's records consist only of the date of the last inspection, with no thickness readings. The inspector should conclude that:

    1. The system's corrosion rate can be taken as negligible
    2. The records are inadequate and further inspection is needed Correct answer.
    3. The inspection interval may be extended based on service history
    4. The system can be re-rated to a higher pressure

    Explanation

    Corrosion rate and remaining life cannot be established without thickness data, so the interval cannot be justified from such thin records. Additional inspection is required to build an adequate record before decisions about the system are made.

  200. Question 200Records, Reports, and Repair/Replacement Documentation

    The records for an operating piping system do not identify the original design thickness or construction code. The most significant consequence is that:

    1. The system's inspection interval may be extended indefinitely
    2. Retirement thickness cannot be taken from the records Correct answer.
    3. The records may be discarded once the next inspection is done
    4. The system must be replaced with new piping of known design

    Explanation

    Retirement thickness is normally derived from design data, so when the records do not provide it the inspector must obtain the information another way, such as an engineering evaluation. The gap does not by itself require replacement or permit any shortcut in the inspection program.

API 570 flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

API 570 scope
Covers in-service metallic piping and components after construction: inspection, repair, alteration, and rerating; it does not cover new construction or pipeline systems.
Piping system definition
In API 570, the assembly of pipe, fittings, flanges, gaskets, bolting, valves, and supports that conveys fluid within defined battery limits.
Inspector versus examiner
An inspector holds a valid API 570 certification and directs inspection; an examiner performs specific NDE examinations and need not hold the API 570 certification.
API 570 exclusions
Excluded from API 570: pipelines under ASME B31.4 and B31.8, boiler and furnace tubes, instrument tubing, and nonmetallic piping.
Owner/user responsibility
The owner/user defines the piping to be covered, establishes inspection plans and intervals, ensures repairs are approved, and retains records for the piping's life.
Rerating definition
A change to the MAWP or temperature rating of existing piping, requiring engineering calculations and approval by an authorized engineer and the inspector.
General corrosion
Uniform metal loss over a broad area from electrochemical reaction with the environment; corrosion rate is expressed in mils per year (mpy) or mm/year.
Chloride stress corrosion cracking
Cracking of austenitic stainless steel exposed to chlorides and tensile stress, often under insulation in the 50–175 °C range; a common CUI mechanism.
Microbiologically influenced corrosion
Localized pitting or attack caused by bacteria in stagnant water, low-flow lines, and dead legs; often found in carbon steel and stainless steel water systems.
Erosion-corrosion
Accelerated metal loss where high-velocity or turbulent flow removes the protective oxide film, typically at elbows, tees, reducers, and downstream of control valves.
Hydrogen blistering
Damage in wet H2S or hydrogen-charging service where atomic hydrogen diffuses into steel and forms internal blisters or stepwise cracking.
Creep
Time-dependent deformation and stress rupture of metal at elevated temperature under sustained load, leading to bulging and cracking of piping.
Corrosion under insulation
External corrosion of carbon steel or chloride SCC of stainless steel beneath insulation and jacketing where water accumulates; hidden until insulation is removed.
Remaining life formula
Remaining life = (actual thickness − minimum required thickness) ÷ corrosion rate; the result sets the maximum inspection interval, which is half the remaining life.
Corrosion rate calculation
Corrosion rate = (previous thickness − current thickness) ÷ time between measurements; long-term rate uses initial thickness and short-term rate uses the last two readings.
Inspection interval rule
API 570 inspection interval is the lesser of half the remaining life or 10 years; if remaining life is under 10 years, the interval cannot exceed half the remaining life.
Alteration definition
A change in piping geometry, materials, or design conditions, or addition of a new component, that requires engineering design review and may require rerating.
Repair definition
Work that restores piping to a safe operating condition without changing its design, such as weld repair of localized metal loss or crack removal.
Hydrostatic test pressure
For ASME B31.3 piping, hydrostatic test pressure is normally 1.5 times the design pressure, adjusted for temperature; pneumatic testing uses lower ratios with extra precautions.
Minimum required thickness
Calculated from the applicable code (e.g., B31.3) using design pressure, diameter, allowable stress, weld joint factor, and corrosion allowance; used as t-min for rating.
Ultrasonic thickness measurement
The primary API 570 method for measuring remaining wall thickness at designated thickness measurement locations; readings are used to calculate corrosion rate and remaining life.
Thickness measurement locations
Pre-marked points on piping where UT readings are taken and compared over time; they are selected at likely thinning areas such as elbows and low points.
ASME Section V
The referenced code for nondestructive examination methods and qualification; API 570 inspections using RT, UT, MT, and PT follow its requirements.
ASME Section IX
The referenced code for welding procedure and performance qualifications; repair and alteration welds under API 570 must be made by welders qualified to it.
API 574
The companion inspection practices document referenced by API 570 for detailed guidance on inspecting piping components, flanges, valves, and supports.
Visual acuity requirement
API 570 inspectors must have corrected near vision of Jaeger 1 or equivalent at 12 inches, plus adequate color vision, verified periodically.
Inspection report contents
Records the inspection date, locations examined, methods, findings, remaining life, recommendations, and the next inspection date, signed by the inspector.
Records retention period
API 570 requires inspection, repair, and rerating records to be kept for the life of the piping system and made available to the inspector.
Repair documentation
Includes the repair description, materials, welding procedure and welder qualifications, NDE results, heat treatment, and pressure test records.
Rerating documentation
Retains the engineering calculations, design basis, approvals, and any new MAWP or temperature limit for the rerated piping.
WPS and PQR
Welding Procedure Specification and Procedure Qualification Record; both must be available for repair or alteration welding performed on API 570 piping.
Thickness measurement records
Chronological UT readings at each TML, with dates and locations, used to compute corrosion rates and remaining life and to set future intervals.

API 570 study guide

Scope, Definitions, and Organization of API 570

What API 570 governs

API 570 covers the inspection, rating, repair, alteration, and rerating of metallic piping systems that are in service in refineries, petrochemical and chemical plants, and similar process facilities. It follows a piping system for its whole in-service life, including idle periods before retirement. Learn the exclusions as well as the inclusions: pipeline transportation piping (covered by ASME B31.4/B31.8 and API 1160), boiler and furnace tubes, instrument tubing, and non-metallic piping fall outside the document.

Roles and definitions

Three roles drive most questions. The owner/user owns the program: it assigns responsibilities, approves inspection intervals, and approves repairs, alterations, and rerating. The authorized inspector is API 570 certified, qualified in the NDE methods used, and works in an inspection function independent of the operating and maintenance organizations. The repair organization must be approved by the owner/user and must use qualified welders and procedures.

Definitions must be applied, not recited: a repair restores the system to safe operation at existing design conditions; an alteration changes something with design implications (material, rating, or a change beyond the original design scope); rerating changes the design pressure or temperature and requires engineering review plus record updates. Deadlegs, injection points, soil-to-air interfaces, and auxiliary piping are named because they attract special inspection attention.

Worked example: replacing 20 ft of 6-in carbon steel line with pipe of the same specification is a repair; substituting 316L stainless steel for that carbon steel is an alteration because the material change has design implications.

Trap: questions that make the inspector the approver of intervals or of a rerating. The owner/user approves; the inspector recommends and documents.

Causes of Deterioration and Failure in Piping Systems

Organize damage by family

Candidates should group mechanisms rather than memorize a list: uniform thinning; localized loss (pitting, crevice, galvanic, under-deposit); velocity-related damage (erosion, erosion-corrosion, cavitation, flashing); environmental cracking (chloride SCC of austenitic stainless steel above roughly 60 C/140 F, caustic SCC, amine cracking, wet H2S cracking); high-temperature attack (sulfidation, naphthenic acid, oxidation, carburization, creep above roughly 800 F for carbon steel); hydrogen damage; metallurgical embrittlement (885 F/sigma, temper embrittlement, brittle fracture, thermal shock); and mechanical damage (water hammer, vibration fatigue at small-bore branch connections, thermal cycling fatigue).

Where questions go wrong

  • CUI is an external mechanism under insulation, commonly in the 10 F to 350 F band for carbon steel systems and aggravated by steam tracing and cyclic service. It is invisible to process-side monitoring, so insulation windows are the detection method.
  • HIC and SSC are both wet-H2S damage but differ: HIC is internal hydrogen-induced cracking and blistering driven by corrosion, while SSC is stress-driven cracking of hard welds and HAZ. Both are mitigated by hardness control and PWHT.
  • Corrosion rate belongs to the metal-environment couple, not the alloy alone: dry hydrocarbon is benign, wet hydrocarbon is not.
  • Deadlegs, low-flow lines, and injection points deteriorate from the process side and often fail at the mixing zone rather than mid-run.

Rule of thumb: any place where water can accumulate, condense, or stagnate, namely low points, deadlegs, bottoms of horizontal lines, soil-to-air interfaces, and under insulation, should be treated as a probable damage site. API 571 is the reference for confirming the mechanism and its inspection options.

Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

Rating: the arithmetic inspectors live by

Rating starts with thickness. Readings at CMLs feed the applicable code formula (ASME B31.3 for process piping) to establish t-min, the retirement thickness at which the component can no longer satisfy design conditions. Compare measured t to t-min. Short-term and long-term corrosion rates are computed from at least two surveys; remaining life = (measured t minus t-min) divided by corrosion rate. The inspection interval is then set so it does not exceed one-half of remaining life and does not exceed the maximum interval for the piping class; Class 1 services, which include injection points and high-deterioration services, take the shortest intervals.

Worked example: measured 0.375 in, t-min 0.250 in, recent rate 0.010 in/yr gives a remaining life of 12.5 years. Half of that is 6.25 years; if the line is Class 1 with a 5-year maximum, the interval is 5 years. Using the long-term rate when an upset has accelerated loss is the classic trap.

Repair, alteration, rerating

Repairs restore design capability: weld repair of pitting, weld build-up, flush patch, section replacement, clamp or enclosure. Temporary repairs require engineering approval and a defined removal date. Welding demands a qualified WPS/PQR, qualified welders, code preheat and PWHT, and hardness control in wet H2S service. Pressure testing after repair follows the applicable code (hydrotest commonly 1.5 times design pressure) unless the owner/user authorizes an alternative such as NDE in lieu of testing. Rerating requires engineering evaluation of every component, including relief devices and supports, may trade pressure for temperature, and must be documented and reflected in the inspection plan.

Inspection Practices, Methods, and Referenced Code Requirements

Inspection types and where to look

API 570 recognizes external inspection, internal (intrusive) inspection, and on-stream inspection that may substitute for internal inspection when justified. CMLs must be placed where damage is most likely and most severe: injection points and downstream mixing zones, low points, deadlegs, turbulent areas, downstream of valves and orifices, and soil-to-air interfaces. Every CML needs a unique identifier marked on the pipe and tied to a drawing. A thickness survey needs enough points to find localized loss, not just a nominal average.

Methods and their limits

UT thickness is the workhorse, but it measures remaining wall, not cracks, and misses tight planar defects unless the grid is fine. Radiography, including profile and double-wall techniques, suits small-bore and insulated lines and is used for CUI screening. PT and MT find surface-breaking flaws; shear-wave UT and phased array find planar flaws; guided wave screens long buried or inaccessible runs; acoustic emission, corrosion probes, and coupons monitor activity. NDE personnel must be qualified under a recognized written practice such as ASNT SNT-TC-1A or an equivalent.

Referenced documents worth recognizing: ASME B31.3, API 571 (damage mechanisms), API 574 (inspection practices), API 577 (welding inspection), API 578 (weld flaw evaluation), API 580 (risk-based inspection), API 583 (CUI), and API 579-1/ASME FFS-1 (fitness-for-service).

Rule of thumb: match method to mechanism. Profile radiography and insulation windows for CUI, shear-wave UT for cracking, fine-grid UT for pitting. A method that cannot detect the expected mechanism does not count as inspection of that mechanism.

Records, Reports, and Repair/Replacement Documentation

What has to be written down

The inspection report records the date, inspection type and methods, CMLs and thickness data, damage found with its mechanism, corrosion rate and remaining life, recommendations, and the next inspection date. It is signed by the inspector and traceable to the specific system. Supporting records include as-built drawings and P&IDs, line class/specification sheets, the inspection plan and intervals, CML location drawings, prior reports, NDE reports, and any fitness-for-service evaluation.

Repair and alteration records are the ones most often tested: the repair organization, the scope, materials with mill test reports, the WPS/PQR and welder qualifications, heat treatment charts, NDE results with acceptance criteria, final thickness or dimensions, and the pressure test record. Rerating documentation must show the engineering basis, the new design pressure and temperature, and that relief devices, supports, and the inspection plan were updated.

Traps

  • Records are not paperwork. The inspector's signature is the evidence that the rating is sound; an undocumented repair behaves like an unverified alteration in an audit.
  • Drawings must show the system as it actually is. A field change without a drawing update is a finding.
  • Retention matters: repair and alteration records must remain available for the life of the piping, and inspection records must be current and retrievable at the time of the next inspection. Verbal turnover is never sufficient.

Rule of thumb: ask whether a new inspector could reconstruct the piping's current condition and design basis from the file alone. If not, the records are deficient, however good the inspection work was.

API 570 cheat sheet

Quick reference

Scope, Definitions, and Organization of API 570

  • API 570 covers in-service metallic piping systems and components originally designed to ASME B31.3, B31.1, or equivalent; it does not cover new construction, pipelines (B31.4/B31.8), boiler or furnace tubes, instrument tubing, or nonmetallic piping.

  • A piping system includes pipe, flanges, gaskets, bolting, valves, fittings, and supports between defined battery limits.

  • Inspection under API 570 means visual and NDE activities performed to determine condition; examination is the NDE itself, performed by an examiner.

  • Only a holder of a valid API 570 certification may act as the inspector; an examiner is qualified for the specific NDE method and need not be API 570 certified.

  • The owner/user establishes the inspection plan, defines which piping is in scope, approves repairs and alterations, and retains records.

  • Alterations and rerating require engineering design approval; a rerating changes the MAWP or temperature rating and must be documented.

  • Repair organizations and welders must be approved by the owner/user; welding must follow ASME Section IX qualified procedures.

  • API 570 does not override the original code of construction; minimum thickness and design rules come from the applicable ASME B31 code.

Quick reference

Causes of Deterioration and Failure in Piping Systems

  • General (uniform) corrosion removes metal evenly; rate in mpy = 1000 × thickness loss in inches ÷ years in service.

  • Localized mechanisms-pitting, crevice, galvanic, and under-deposit corrosion-cause penetration with little overall metal loss.

  • CUI affects carbon steel externally and causes external chloride SCC in austenitic stainless steel, typically between 50 °C and 175 °C (120–350 °F).

  • Erosion-corrosion accelerates at high velocity, turbulence, or wet steam; inspect elbows, tees, reducers, and downstream of valves.

  • MIC produces pitting in stagnant, low-flow, or dead-leg water service; symptoms include tubercles and black deposits.

  • Wet H2S service can cause hydrogen blistering, HIC, and sulfide stress cracking; hardness and PWHT controls apply.

  • At elevated temperature, creep and stress rupture produce bulging and cracking; graphitization affects carbon steel above about 800 °F.

  • Cyclic or vibrating service causes fatigue cracking, usually initiating at weld toes, branch connections, and supports.

  • Buried piping is subject to soil corrosion; coating condition and cathodic protection determine the external corrosion rate.

Quick reference

Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

  • Remaining life = (actual thickness − minimum required thickness) ÷ corrosion rate; use the governing (usually higher short-term) rate.

  • Inspection interval must not exceed the lesser of half the remaining life or 10 years; if remaining life is below 10 years, the interval cannot exceed half that life.

  • Corrosion rate = (previous thickness − current thickness) ÷ elapsed time; long-term rate uses initial-to-current readings, short-term rate uses the last two.

  • Minimum required thickness is calculated by the applicable ASME B31 code from design pressure, diameter, allowable stress, weld joint factor, and corrosion allowance.

  • A repair restores safe condition without changing design; an alteration changes geometry, materials, or design conditions and requires engineering approval.

  • Rerating changes MAWP or temperature rating and requires calculations, inspector review, and updated records.

  • Repair and alteration welds require qualified WPS/PQR per ASME Section IX, welder qualification, and NDE as specified.

  • A hydrostatic test is typically 1.5 × design pressure for B31.3 piping; pneumatic testing is permitted at lower ratios with added safeguards.

  • Injection points and mixing points are high-corrosion locations and require shorter inspection intervals than the parent line.

Quick reference

Inspection Practices, Methods, and Referenced Code Requirements

  • Ultrasonic thickness measurement is the principal method for determining remaining wall; readings at fixed TMLs are compared over time.

  • TMLs are placed at elbows, tees, reducers, low points, and areas of turbulence or known corrosion.

  • NDE methods include VT, PT, MT, UT, and RT; performance and qualification follow ASME Section V.

  • Welding qualifications follow ASME Section IX; weld inspection follows the applicable B31 code and API 577.

  • API 574 provides detailed piping inspection practices; API 571 describes damage mechanisms; API 578 covers material verification.

  • Inspectors must have Jaeger 1 (or equivalent) near vision at 12 inches and adequate color vision, re-verified periodically.

  • Insulation must be removed at suspect CUI locations to allow external visual and UT inspection.

  • Pressure tests verify tightness and strength after repairs or alterations; test medium, temperature, and pressure are recorded.

Quick reference

Records, Reports, and Repair/Replacement Documentation

  • Records must be retained for the life of the piping system and include inspection reports, thickness data, repairs, alterations, and reratings.

  • Each inspection report records date, locations, methods, findings, remaining life, recommendations, and next inspection date.

  • Repair records include repair description, materials, WPS/PQR, welder ID, NDE results, heat treatment, and pressure test data.

  • Rerating records include design calculations, new MAWP and temperature, approvals, and revised inspection requirements.

  • Thickness records list each TML, its location, date, and reading, enabling corrosion-rate and remaining-life calculations.

  • Alteration records include design drawings, calculations, and engineering approval.

  • Records must be available to the API 570 inspector and authorized personnel; controlled electronic records are acceptable.

API 570 key terms

Piping System

An assembly of interconnected piping components-pipe, fittings, flanges, bolting, gaskets, valves, and the pressure-containing parts of other components-that shares the same design and operating conditions and can be isolated as a unit.

Related: Piping Circuit, Owner/User
Piping Circuit

A section of a piping system that shares common characteristics such as material, service, and operating conditions, so that a single representative set of monitoring locations and one corrosion rate can be applied to the whole section.

Related: Piping System, Condition Monitoring Location
Owner/User

The organization that owns or operates the piping system and is responsible for its safe operation, including setting inspection intervals, providing qualified inspectors, and approving repairs and alterations.

Related: Authorized Piping Inspector, Inspection Interval
Authorized Piping Inspector

A person employed by the owner/user or by an authorized inspection agency who is certified under the API 570 program, or otherwise qualified to the satisfaction of the jurisdiction, and assigned to inspect piping systems.

Related: Authorized Inspection Agency, Owner/User
Authorized Inspection Agency

An organization acceptable to the jurisdiction, such as an insurer's inspection department or a recognized inspection body, that supplies qualified inspection personnel and services to the owner/user.

Related: Authorized Piping Inspector, Jurisdiction
Jurisdiction

The governmental or regulatory authority that has adopted the inspection code and holds legal responsibility for enforcing its requirements at a particular facility or location.

Related: Authorized Inspection Agency
Repair Organization

Any person or company that performs repairs, alterations, or rerating of piping, and that must be acceptable to the owner/user and work under an approved quality system with qualified procedures and personnel.

Related: Repair, Hold Point
Corrosion Rate

The speed at which wall thickness is lost to corrosion or erosion, usually expressed in mils per year or millimeters per year and calculated by dividing measured thickness loss by the elapsed time between measurements.

Related: Remaining Life, Corrosion Allowance
Corrosion Allowance

Extra wall thickness provided beyond the thickness needed to contain pressure, so that expected deterioration during service can occur before a component reaches its retirement thickness.

Related: Minimum Required Thickness, Corrosion Rate
Corrosion Under Insulation

External corrosion of piping beneath insulation or fireproofing, most often on carbon steel operating roughly between 10 degrees F and 350 degrees F, where moisture can enter and remain trapped against the metal.

Related: External Inspection, Corrosion Rate
Stress Corrosion Cracking

Cracking produced by the combined action of sustained tensile stress and a specific corrosive environment, such as chlorides acting on austenitic stainless steel, often with little or no visible metal loss.

Related: Fatigue, Corrosion Rate
Injection Point

A location where chemicals, water, or another stream is injected into or mixed with the main process flow, creating locally higher corrosivity that normally calls for closer inspection and dedicated monitoring locations.

Related: Deadleg, Condition Monitoring Location
Deadleg

A portion of piping that normally carries no flow, such as an unused branch or bypass, allowing corrosive fluids to stagnate and concentrate and making the area prone to accelerated localized attack.

Related: Injection Point, Corrosion Rate
Erosion-Corrosion

Accelerated metal loss caused by flowing fluid wearing away protective oxide scale while fresh metal underneath continues to corrode, typically found at elbows, tees, reducers, and downstream of control valves.

Related: Corrosion Rate, Injection Point
Creep

Slow, time-dependent permanent deformation of metal held under sustained stress at elevated temperature, which can lead to bulging, cracking, or rupture in high-temperature piping services.

Related: Fatigue
Fatigue

Progressive cracking caused by repeated or cyclic stresses such as vibration, thermal cycling, or pressure swings, which initiate and grow cracks at welds and other stress concentrations.

Related: Creep, Stress Corrosion Cracking
Maximum Allowable Working Pressure

The highest internal pressure permitted at the design temperature for a piping system, established so that the allowable stress of the weakest component in the system is not exceeded.

Related: Rerating, Minimum Required Thickness
Repair

Work required to restore a piping system to a safe operating condition that does not amount to an alteration, such as replacing a corroded section with like material, weld buildup, or patching.

Related: Alteration, Replacement in Kind, Repair Organization
Alteration

A physical change in a piping system that affects its pressure-containing capability or design conditions and is not a replacement in kind, such as changing line size, adding a branch, or changing material.

Related: Repair, Rerating, Replacement in Kind
Rerating

A change to the pressure or temperature limits of an existing piping system, or to its service fluid, carried out through engineering evaluation and documented so the system stays safe at the new conditions.

Related: Alteration, Maximum Allowable Working Pressure
Replacement in Kind

Replacement of a component with another of the same configuration, pressure rating, and material, requiring no design change and therefore not treated as an alteration.

Related: Repair, Alteration
Inspection Interval

The maximum time permitted between inspections of a piping system, set by the owner/user from corrosion rate, remaining life, service risk, and any limits imposed by the code or jurisdiction.

Related: Risk-Based Inspection, Remaining Life
Remaining Life

The estimated time a component can continue operating at current conditions before its wall thickness reaches the retirement thickness, calculated by dividing usable thickness by the corrosion rate.

Related: Corrosion Rate, Retirement Thickness
Retirement Thickness

The wall thickness at which a piping component is considered unfit for continued service and must be rerated, repaired, or replaced, normally taken as the minimum required thickness calculated for the design conditions.

Related: Minimum Required Thickness, Remaining Life
Minimum Required Thickness

The thinnest wall that can safely contain the design pressure at design temperature, computed from pressure, diameter, allowable stress, and the weld joint and corrosion allowances required by the applicable code.

Related: Retirement Thickness, Corrosion Allowance
Risk-Based Inspection

A structured method of prioritizing and scheduling inspection according to the likelihood and consequence of failure, so that inspection effort is concentrated where risk is highest.

Related: Inspection Interval, Condition Monitoring Location
Hold Point

A designated step in a repair or inspection activity at which work must stop so the authorized inspector can examine and approve the work before the job is allowed to continue.

Related: Repair Organization, Repair
Hydrostatic Test

A pressure test in which piping is filled with water or another liquid and pressurized above its operating pressure to verify strength and leak tightness before being returned to service.

Related: Pressure Relief Device, Alteration
Nondestructive Examination

Inspection methods such as ultrasonic, radiographic, magnetic particle, liquid penetrant, and visual testing that reveal flaws, cracks, or thickness loss without damaging the component being examined.

Related: Ultrasonic Thickness Measurement, Condition Monitoring Location
Ultrasonic Thickness Measurement

A technique that determines remaining wall thickness by timing sound pulses reflected from the far surface or an internal interface, providing data used to calculate corrosion rates and remaining life.

Related: Condition Monitoring Location, Corrosion Rate
Condition Monitoring Location

A specific point or area on a piping circuit designated for repeated thickness measurements or other examination, selected because it is expected to represent the worst deterioration in that circuit.

Related: Piping Circuit, On-Stream Inspection
On-Stream Inspection

Inspection carried out while the piping system remains in operation, using external visual checks, thickness measurements, and other nonintrusive techniques without shutting down or opening the system.

Related: External Inspection, Condition Monitoring Location
Internal Inspection

Examination of the inside surfaces of piping, normally performed during a shutdown when the system is opened, cleaned, and inspected visually or by nondestructive methods.

Related: On-Stream Inspection, Nondestructive Examination
External Inspection

Examination of the outside of piping, insulation, supports, and appurtenances to find leaks, corrosion, coating damage, misalignment, vibration, and hot spots while the system is operating.

Related: On-Stream Inspection, Corrosion Under Insulation
Pressure Relief Device

A device such as a relief valve, rupture disk, or rupture pin installed to protect piping and equipment from overpressure by relieving fluid when the set pressure is reached.

Related: Hydrostatic Test, Inspection Interval
Piping and Instrumentation Diagram

A drawing showing the piping, equipment, valves, instruments, and control loops of a process, used as a reference for tracing lines, identifying boundaries, and planning inspections.

Related: Isometric Drawing, Inspection Record
Inspection Record

Documented results of inspections, including measurements, findings, calculated corrosion rates, remaining life, and recommendations, kept for the life of the system and used to plan future inspection intervals.

Related: Inspection Interval, Piping and Instrumentation Diagram
Isometric Drawing

A pictorial drawing of a single piping line showing its routing, fittings, valves, and coordinates, commonly used to identify inspection locations, define repair scope, and record line configuration.

Related: Piping and Instrumentation Diagram, Inspection Record

API 570 study plan

8 weeks · About 7 hours per week

Week 1

Causes of Deterioration and Failure in Piping Systems

  • Classify at least 15 deterioration mechanisms from API 571 by susceptible alloy, process environment, and the piping component where they initiate.

  • Distinguish CUI, chloride SCC, HTHA, erosion-corrosion, and galvanic corrosion by the inspection method that detects each most reliably.

  • Map each mechanism to the API 570 inspection response it triggers (CML placement, location emphasis, interval shortening).

  • Solve 25 scenario items that describe a failure and ask which mechanism explains it.

Your checkpoint

One-page damage-mechanism matrix (mechanism to susceptible material to typical location to detection method) covering 15 mechanisms, self-quizzed to 90% accuracy.

Week 2

Causes of Deterioration and Failure in Piping Systems & Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

  • Compute long-term and short-term corrosion rates from two or more sets of survey thickness readings.

  • Calculate remaining life and minimum required thickness for straight pipe and formed components using the ASME B31.3 formulas cited by API 570.

  • Set inspection intervals and maximum intervals from remaining life and the applicable remaining-life fractions.

  • Apply shorter-interval logic where mechanisms such as CUI, injection points, or soil-to-air interfaces govern.

Your checkpoint

Ten fully worked corrosion-rate, remaining-life, and interval problems with answers and the clause reference supporting each step.

Week 3

Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping

  • Differentiate repair, alteration, and rerating using API 570 definitions and worked examples.

  • Apply welded-repair requirements: authorization, WPS/PQR qualification, preheat and PWHT, and hardness verification.

  • Evaluate acceptability of temporary repairs and clamped or boxed enclosures, including time limits and documentation.

  • Assign inspection hold points and required NDE for a described repair scenario.

Your checkpoint

Repair-versus-alteration-versus-rerating decision checklist applied to 12 written scenarios, each with a verdict and the documentation it requires.

Week 4

Inspection Practices, Methods, and Referenced Code Requirements

  • Match NDE methods (VT, RT, UT, MT, PT, WFMT, ACFM, shear-wave UT) to the discontinuities they detect and the acceptance criteria they invoke.

  • Select CML grid density and placement for a given piping circuit based on mechanism, geometry, and expected corrosion pattern.

  • Apply API 570 inspection requirements for buried, insulated, and high-temperature piping systems.

  • Extract the referenced-code requirements from ASME B31.3 and B16.5 that govern in-service inspection decisions.

Your checkpoint

NDE selection table plus a completed CML layout for one example circuit with a written justification for each location.

Week 5

Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping & Inspection Practices, Methods, and Referenced Code Requirements

  • Determine rerating outcomes: reduced MAWP, changed service, and pressure-temperature ratings of flanges and components.

  • Apply requirements for hot taps, line blanks, valve replacement, and bolted joint assembly and integrity.

  • Delineate owner/user, inspector, and repair-organization responsibilities for repair and alteration acceptance.

  • Apply weld acceptance criteria from the referenced fabrication code to given discontinuity indications.

Your checkpoint

Twenty flashcards of numeric and acceptance criteria plus 15 practice problems solved and cross-checked against clause references.

Week 6

Scope, Definitions, and Organization of API 570

  • State the scope and exclusions of API 570 and describe how it interfaces with API 510, API 653, and ASME B31.3.

  • Define key terms including authorized inspector, CML, inspection, repair, alteration, rerating, and MAWP.

  • Describe the roles of the owner/user, inspector, repair organization, and jurisdictional authority.

  • Explain the qualification and certification requirements for an API 570 inspector.

Your checkpoint

Definitions sheet for 35 key terms, self-tested to 90% unaided recall.

Week 7

Records, Reports, and Repair/Replacement Documentation

  • Draft an inspection report containing every element API 570 requires.

  • Record CML thickness data and remaining life in a format traceable to the inspection plan.

  • Assemble a repair/alteration package with the required attachments: WPS/PQR, NDE results, and rerating calculations.

  • Determine record retention periods and record-keeping obligations for inspection and repair documentation.

Your checkpoint

One complete mock inspection report and one repair package for a sample circuit, checked line by line against a requirements checklist.

Week 8

Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping & Inspection Practices, Methods, and Referenced Code Requirements

  • Complete a full-length timed mock exam covering all five domains and tabulate every miss by domain and error type.

  • Re-work every missed question in the repair, alteration, rerating, and inspection-practice areas back to the governing clause.

  • Rehearse thickness, corrosion-rate, remaining-life, and interval calculations until ten consecutive items are correct without notes.

  • Build a one-page last-look sheet listing interval-setting rules and repair/alteration/rerating triggers.

Your checkpoint

Mock exam score report with a domain breakdown, a written remediation log, and the completed last-look sheet.

Milestones

Week 2: Score 80% or better on a closed-book set of 20 corrosion-rate and remaining-life problems.

Week 4: Score 75% or better on a 40-question timed quiz covering Domains 2, 3, and 4.

Week 6: Recall 35 Domain 1 definitions with at least 90% accuracy on a self-administered quiz.

Week 7: Mock inspection report and repair package satisfy 100% of the checklist of required elements.

Week 8: Score 80% or better overall on the full-length mock exam with no domain below 70%.

API 570 exam day

Your checklist

Government-issued photo ID in the exact name used on your registration

Bring the original document, not a photocopy. If the name on your ID differs from your registration in any way (middle name, suffix, maiden name), contact the certification body before exam day to correct it. Confirm with the provider which specific ID forms are accepted.

Appointment confirmation and test-center address

Save a screenshot of the confirmation plus the street address and phone number of the site. Do a mapping check the day before so you know the entrance, parking, and how long the walk from the lot to the room takes.

Arrival time and admittance cut-off

Ask the provider what arrival lead time is required and what happens if you arrive late - many testing programs refuse admittance after a set window. Write the target arrival time down rather than estimating it on the morning.

Written confirmation of the reference-material policy

Do not assume you may bring code books, standards, notes, or formula sheets. Get the permitted/prohibited list from the provider in writing and pack accordingly. Anything not explicitly allowed should stay home or in the car.

Written confirmation of the calculator policy

Confirm whether a calculator is provided on screen, whether a physical model is allowed, and which models are banned. Bring only a model that appears on the approved list - an unapproved device can be confiscated or end your session.

Pacing plan rehearsed on a timed practice set

Do at least one full-length timed practice run in the two weeks before the exam so you know your minutes-per-question budget and your personal checkpoint (for example, where you should be at the halfway mark).

A short personal formula and concept sheet for the final review only

Use it for the last 48 hours of study; leave it at home. Focus on the calculations and code-organization habits you will need to solve items from memory, since you are unlikely to have reference documents at the desk.

Logistics: transport, backup ride, and test-center contact number

Have a fallback plan for traffic, weather, or a cancelled train. Carry the site's phone number so you can call if you are delayed rather than simply arriving late.

Pre-exam physical plan

Decide in advance on sleep timing, a normal (not heavy or unfamiliar) meal, hydration, and any medication. Avoid experimenting with caffeine levels on exam day.

Clarify break and personal-item rules before you sit

Ask at check-in how breaks work, whether the clock stops, and where personal items must be stored. Knowing this in advance prevents losing time to confusion mid-session.

Plan the day

Final 72 hours

Stop learning new material. Rework your weak areas using your own notes and the standards' structure (scope, responsibilities, inspection frequency, repair/alteration rules). Do one timed mixed-topic set per day and review every miss for the reason (knowledge gap vs. misread question). Confirm your ID name matches your registration and resolve any discrepancy now, not on exam day.

Final 72 hours

Print or save the appointment confirmation, confirm the test-center address and required arrival time with the provider, and plan the route and parking. Check the permitted/prohibited items list one more time.

24 hours before

Light review only: skim your formula sheet, the inspection-frequency logic, and the definitions you keep confusing. Pack your ID, confirmation, and approved calculator. Lay out clothes and decide the departure time. Set two alarms. Aim for a normal night's sleep - do not stay up cramming.

Morning of

Eat a normal meal, hydrate moderately, and leave with a buffer that gets you there earlier than the required arrival time. Leave your phone, smartwatch, and study notes in the car or at home unless the provider confirms they may be stored on site. Re-read only your one-page summary on the way; stop reviewing once you enter the building.

At check-in

Have your ID out, listen to the proctor's instructions, and ask any clarifying questions about breaks, scratch materials, or the on-screen calculator before the timer starts. Verify your name and the exam you are taking appear correctly on the screen.

During the test - first pass

Answer the questions you know, flag anything requiring a calculation or close reading, and keep moving. Do not let a single unfamiliar code citation cost you five minutes. Track your pace against your rehearsed checkpoint.

During the test - second pass

Return to flagged items with the remaining time. Eliminate obviously wrong options, then choose. Re-read the stem for words like 'minimum', 'maximum', 'not', and 'first' before committing to a change - second-guessing on wording alone usually hurts.

Final five minutes

Confirm no question is left blank unless the provider's scoring rules make blank answers preferable (verify this in advance). Submit deliberately and keep your printed score report or confirmation of completion if one is issued.

Rules to check

  • Bring photo ID that matches your registered name exactly; a mismatch can result in being turned away, and the remedy must be arranged with the certification body before exam day.

  • Treat the exam as closed-book unless the provider has told you in writing otherwise. Bringing unauthorized reference material, notes, or an unapproved device into the testing room is a conduct violation, not a technicality.

  • Phones, smartwatches, and other electronic devices must be silenced and stored as directed by the proctor; confirm storage arrangements at check-in rather than keeping a device on your person.

  • Ask the provider in advance how breaks are handled - whether the clock runs during a break, whether breaks are available at all, and whether you must sign out. Do not infer this from another program's rules.

  • Scoring and guessing policy varies by program: confirm whether unanswered items are counted incorrect and whether there is any penalty for guessing before you decide to leave items blank.

  • Pass/fail results are typically reported by the certification body after the exam rather than by the proctor; confirm the reporting timeline and appeal process with the provider instead of relying on what other candidates tell you.

  • If you believe an item is defective or the equipment fails, stop and notify the proctor immediately and note the time; unresolved issues raised after you leave are difficult to remedy.

API 570 FAQ

How many API 570 practice questions are available?

The practice set has 200 API 570 questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many API 570 flashcards are available?

The flashcard set has 32 API 570 cards. Each card shows the term and its definition.

Which topics does the API 570 study material cover?

The API 570 study material has 5 sections, including Scope, Definitions, and Organization of API 570, Causes of Deterioration and Failure in Piping Systems, and Inspection, Rating, Repair, Alteration, and Rerating of In-Service Piping.

What format facts does the catalog list for the API 570 exam?

The catalog lists these item types: multiple choice for the API 570 exam.