Alberta Class 6 Motorcycle Test Practice Test

Alberta Class 6 Motorcycle Test overview

  • 200 practice questions
  • 32 flashcards
  • 4 study guide topics
  • 40 key terms

What you'll study

  • Alberta traffic laws and rules of the road applicable to motorcycles25%
  • Safe motorcycle riding practices and hazard awareness25%
  • Motorcycle controls, handling and vehicle familiarity25%
  • Signs, signals, road markings and right-of-way25%

The Alberta Class 6 Motorcycle Test refers to the knowledge (written) test a rider must pass to obtain an Alberta Class 6 motorcycle learner's licence, and it is the starting point of the province's graduated licensing path for motorcycles. It is intended for new riders, and for drivers who already hold a Class 5 licence and want to add motorcycle privileges. This independent study page organizes practice material around four areas: Alberta traffic laws and rules of the road as they apply to motorcycles; safe riding practices and hazard awareness; motorcycle controls, handling and vehicle familiarity; and signs, signals, road markings and right-of-way. Because it is a knowledge test rather than a riding evaluation, preparation should combine reading the official Alberta driver's guide for motorcycles with repeated multiple-choice practice and review of every missed item. This page is not affiliated with, endorsed by, or operated by the Government of Alberta, and it is not an official test. Important caution: the official Alberta.ca pages for the motorcycle knowledge test and motorcycle road test returned "Page not found" when checked on 2026-10-31, so no current official details on question count, time limit, passing score, fee, retake rules or licence validity could be confirmed. All such figures on this page are marked unverified and should be checked against current Alberta.ca content or a registry agent before booking.

Common mistakes

Treating a motorcycle as exempt from full stops and instead slowing to a rolling 'pause' at stop signs and red lights before turning right.

Riders carry over the habit of a rolling check from cycling or from watching experienced riders, and the bike's light weight makes a rolling stop feel stable and safe.

What to do instead

Drill the full stop as a distinct sequence: both wheels stopped, both feet or the left foot down, a deliberate left-right-left scan, then proceed. Practise at empty intersections until the stop is automatic.

Riding in the centre of a lane or beside another vehicle in the same lane instead of occupying a full lane position.

New riders come from a car mindset where lane centring feels 'correct', and they underestimate how much a motorcycle's narrow profile invites other drivers to share the lane.

What to do instead

Memorise that a motorcycle is entitled to a whole lane. Choose a lane position (left, centre, right third) based on visibility and escape routes, and move to block lane-sharing when a car drifts over.

Entering a curve too fast and then braking or chopping the throttle mid-corner.

Riders judge corner speed by car experience, and the instinct to brake when scared overrides the fact that braking mid-lean reduces stability and stands the bike up.

What to do instead

Set speed before the corner using the 'slow, look, lean, roll' sequence: brake to entry speed while upright, look through to the exit, lean, then maintain or gently roll on throttle through the curve.

Following too closely because the rider only accounts for their own stopping distance and not reaction time plus road surface.

Motorcycles stop shorter than cars in theory, so riders shrink the gap, forgetting that a rear-end collision is far more dangerous for them and that gravel or rain extends distance.

What to do instead

Use a minimum two-second following gap in good conditions, extend to three or four seconds in rain, gravel or darkness, and add distance whenever a vehicle behind is tailgating so you have room to slow gradually.

Failing to scan for surface hazards such as gravel, sand, painted lines, metal grates and tar snakes, and then braking or swerving abruptly on them.

Riders focus on traffic and treat the road surface as uniform, and they do not yet know that traction is sharply reduced on these surfaces and that abrupt inputs there cause a slide.

What to do instead

Build a constant near-far surface scan. Cross hazards as upright and perpendicular as possible, avoid braking or leaning hard on them, and reduce speed before reaching them rather than reacting on top of them.

Using only the front brake hard, or only the rear brake, instead of applying both progressively.

Riders fear pitching over the front and default to the rear, or they grab the front lever in a panic; both habits come from not having practised maximum braking in a controlled space.

What to do instead

Practise emergency stops in an empty lot: apply both brakes together, front pressure progressive rather than grabbed, rear light to avoid lockup, and keep the bike straight. Repeat until the coordinated squeeze is automatic.

Looking down at the controls or at the ground directly in front of the front wheel while turning or stopping.

New riders watch their hands and feet to confirm they are doing the right thing, and target fixation pulls the eyes to the hazard or the ground.

What to do instead

Keep the head up and eyes on the intended path; the bike follows the gaze. Learn control locations by feel with the bike stationary and engine off before riding, so no glance downward is needed.

Misreading a stale green or an unprotected left-turn situation and proceeding without confirming right-of-way.

Riders assume a green means go and focus on their own movement, missing that right-of-way at a left turn depends on oncoming traffic and that a stale light may change mid-intersection.

What to do instead

At every intersection, verify the light state, check oncoming traffic before turning left, and treat a green as permission to proceed only after confirming the intersection is clear and your path is protected.

Ignoring or misreading lane markings such as solid versus broken lines, turn lanes, and shared centre turn lanes, and changing lanes across a solid line.

Riders read markings casually because they are focused on traffic gaps, and motorcycle training often under-emphasises marking rules compared with vehicle handling.

What to do instead

Review the marking rules explicitly: solid lines are not crossed to pass, broken lines permit a lane change when safe, and a shared centre turn lane is for turning only, never for travelling or passing.

Failing to position for visibility and being seen, such as lingering in a vehicle's blind spot or beside a large truck's turning path.

Riders assume being smaller means being noticed, and they drift into blind spots while matching another vehicle's speed rather than actively managing space.

What to do instead

Ride where drivers can see you: avoid blind spots, never linger beside a large vehicle, and stay back from trucks that may swing wide on a turn. Use lane position and headlight to stay visible, and always have an escape route planned.

Exam requirements can change. Confirm current details with the exam provider.

Alberta Class 6 Motorcycle Test practice

200 questions. Each one lists the choices, the correct answer, and an explanation. With JavaScript, this list opens one question at a time. The checker at the top of this page saves progress in this browser when it is available.

  1. Question 1Alberta traffic laws and rules of the road applicable to motorcycles

    Under Alberta law, a person operating a motorcycle on a highway must wear a helmet that meets approved standards and is fastened securely. Who is required to comply with this rule?

    1. Only riders under 18 years of age
    2. Only the operator when carrying a passenger
    3. Both the operator and any passenger Correct answer.
    4. Only riders on highways outside cities

    Explanation

    Alberta's helmet requirement applies to every person riding on or operating a motorcycle, including passengers. The helmet must be of an approved type and properly fastened. Age and road type do not change the requirement.

  2. Question 2Alberta traffic laws and rules of the road applicable to motorcycles

    In Alberta, which of the following is required before a motorcycle may be operated on a highway?

    1. A written trip plan filed with the police
    2. A valid vehicle registration and proof of insurance Correct answer.
    3. A passenger seated behind the operator
    4. A windshield of at least 30 centimetres

    Explanation

    A motorcycle operated on a highway must be registered and insured, and the operator must carry proof of registration and insurance. Trip plans and mandatory windshields are not required. Passengers are optional.

  3. Question 3Alberta traffic laws and rules of the road applicable to motorcycles

    When riding at night in Alberta, a motorcycle must display which lights?

    1. A white headlight only
    2. A red taillight only
    3. Hazard flashers at all times
    4. A white headlight and a red taillight Correct answer.

    Explanation

    At night a motorcycle must show a white light to the front and a red light to the rear. These lights make the narrow profile of the motorcycle visible to other drivers. Hazard flashers are not a substitute for required lighting.

  4. Question 4Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider in Alberta intends to turn left at an intersection. Where should the rider normally position the motorcycle before turning?

    1. On the shoulder to the right of traffic
    2. In the right portion of the lane
    3. Near the left edge of the lane or in the left turn lane Correct answer.
    4. Directly on the centre line of the road

    Explanation

    A left turn is made from the left portion of the lane, or from a designated left turn lane where one exists. Turning from the right side invites vehicles to pass on the left. The shoulder is not a travel lane.

  5. Question 5Alberta traffic laws and rules of the road applicable to motorcycles

    When a motorcycle carries a passenger in Alberta, the motorcycle must have:

    1. A windshield
    2. A passenger seat and footrests for the passenger Correct answer.
    3. A second headlight
    4. A sidecar attached

    Explanation

    A motorcycle carrying a passenger must be equipped with a proper passenger seat and footrests for that passenger. A sidecar, windshield, or extra headlight is not required. The passenger must also wear an approved helmet.

  6. Question 6Alberta traffic laws and rules of the road applicable to motorcycles

    In Alberta, a motorcycle may share a traffic lane with another vehicle:

    1. Only if the other vehicle is also a motorcycle
    2. Only on multi-lane highways
    3. Never, except as specifically permitted Correct answer.
    4. Whenever traffic is moving slowly

    Explanation

    Lane sharing with another vehicle is not permitted; each vehicle is entitled to a full lane. The general rule is one vehicle per lane, with narrow exceptions set out in law. Slow traffic or multiple lanes do not create a right to share.

  7. Question 7Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider approaches a stop sign. What must the rider do?

    1. Sound the horn and continue
    2. Slow down and proceed if the way is clear
    3. Come to a complete stop before the stop line or crosswalk Correct answer.
    4. Stop only if another vehicle is present

    Explanation

    A stop sign requires a complete stop before the stop line, crosswalk, or intersection. Rolling stops are not permitted. The rider may then proceed only when it is safe.

  8. Question 8Alberta traffic laws and rules of the road applicable to motorcycles

    Which statement best describes the purpose of a motorcycle's turn signals in Alberta traffic?

    1. They are only needed at night
    2. They are optional if the rider uses hand signals instead
    3. They must be used to signal every lane change and turn Correct answer.
    4. They are only needed on highways

    Explanation

    Turn signals communicate a rider's intentions to other road users and must be used for turns and lane changes. Hand signals may be used where signals are not required or when they help. Signalling is required day and night.

  9. Question 9Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle is following a large truck. To reduce the risk from the truck's blind spots, the rider should:

    1. Ride in the truck's mirror blind spot to stay visible
    2. Ride alongside the truck's rear wheels
    3. Keep a following distance that lets the rider see the truck's mirrors Correct answer.
    4. Follow closely so other vehicles cannot enter the gap

    Explanation

    A rider who can see the truck driver's mirrors is more likely to be seen. Following at a distance that keeps the rider out of blind spots reduces risk. Riding close or alongside the rear wheels places the rider in hidden zones.

  10. Question 10Alberta traffic laws and rules of the road applicable to motorcycles

    When riding on a wet road, a motorcycle rider should generally:

    1. Ride on the painted lane markings for better grip
    2. Brake harder and later than in dry conditions
    3. Increase following distance and reduce speed Correct answer.
    4. Lean more sharply into corners

    Explanation

    Wet pavement reduces traction, so a rider should slow down and leave a larger following gap. Painted markings and metal surfaces become especially slippery when wet. Smooth, gentle inputs help maintain control.

  11. Question 11Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is entering a curve and realizes the entry speed is too high. The safest response is to:

    1. Increase the lean angle abruptly
    2. Grab the front brake firmly and straighten the bike
    3. Apply both brakes smoothly while maintaining the curve line Correct answer.
    4. Release the throttle and coast through the curve

    Explanation

    Smooth application of both brakes while holding the intended line helps reduce speed without upsetting the motorcycle. Abrupt braking or steering inputs can cause a loss of traction. Planning speed before the curve is the best prevention.

  12. Question 12Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider must cross railway tracks that run at a sharp angle to the road. The rider should:

    1. Cross at a sharp angle to the tracks
    2. Accelerate hard just before the tracks
    3. Cross as close to a right angle as possible Correct answer.
    4. Stop on the tracks to check for trains

    Explanation

    Crossing tracks at as close to a right angle as possible reduces the chance of the tires catching in the rails or flangeway. The rider should slow down, cross squarely, and avoid braking on the tracks. Stopping on the tracks is dangerous.

  13. Question 13Alberta traffic laws and rules of the road applicable to motorcycles

    In Alberta, when may a motorcycle rider proceed through an intersection on a red light?

    1. Never, under any circumstances
    2. After slowing down and checking for traffic
    3. When the rider is on a motorcycle with a small engine
    4. Only when turning right after a complete stop, where permitted Correct answer.

    Explanation

    A right turn on a red light is permitted after a complete stop, unless a sign prohibits it, and only when the way is clear. Proceeding straight through a red light is not allowed. Engine size does not create an exception.

  14. Question 14Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is travelling on a road with a posted speed limit of 60 km/h. Which statement about the rider's speed is correct?

    1. The rider may exceed the limit to pass slower traffic
    2. The rider must not exceed the posted limit Correct answer.
    3. The rider may follow the flow of traffic regardless of the limit
    4. The rider may exceed the limit when no police are visible

    Explanation

    The posted speed limit is the maximum permitted speed in good conditions. A rider may need to drive below the limit when conditions are poor. Passing or following traffic does not justify exceeding the limit.

  15. Question 15Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is approaching a pedestrian crosswalk where a pedestrian is waiting to cross. The rider should:

    1. Continue at the same speed if the pedestrian has not stepped off the curb
    2. Sound the horn to warn the pedestrian
    3. Yield and allow the pedestrian to cross Correct answer.
    4. Pass the pedestrian on the left without stopping

    Explanation

    Drivers and riders must yield to pedestrians at crosswalks. A pedestrian waiting at a crosswalk is entitled to cross safely. Riders should slow and stop as needed.

  16. Question 16Alberta traffic laws and rules of the road applicable to motorcycles

    A rider's motorcycle begins to wobble at highway speed. The rider should:

    1. Stand on the pegs to shift weight forward
    2. Ease off the throttle and hold the bars firmly without overcorrecting Correct answer.
    3. Grip the handlebars tightly and brake hard
    4. Accelerate hard to stabilize the bike

    Explanation

    During a wobble the rider should reduce speed gradually and keep a firm but relaxed grip. Abrupt braking or acceleration can worsen the wobble. Holding a steady line lets the motorcycle settle.

  17. Question 17Alberta traffic laws and rules of the road applicable to motorcycles

    When riding in a group in Alberta, the safest formation generally keeps riders:

    1. Side by side in a single lane
    2. Staggered so each rider has room to maneuver Correct answer.
    3. In a single file at all times regardless of conditions
    4. Bunched tightly together

    Explanation

    A staggered formation gives each rider space and a view of the road ahead. It also provides room to react to hazards. Tight bunching reduces reaction space and visibility.

  18. Question 18Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is stopped at an intersection and a large truck is turning right. The rider should:

    1. Pass the truck on the right as it turns
    2. Move into the space on the truck's right side
    3. Assume the truck driver has seen the motorcycle
    4. Stay back and allow the truck to complete the turn Correct answer.

    Explanation

    Large trucks need extra space and swing wide when turning, creating a dangerous area on the inside of the turn. Staying back keeps the rider clear of that squeeze zone. The driver may not see a motorcycle in the blind spot.

  19. Question 19Alberta traffic laws and rules of the road applicable to motorcycles

    A rider must make an emergency stop on a motorcycle with front and rear brakes. The most effective technique is to:

    1. Downshift and coast without braking
    2. Use only the rear brake to avoid a front-wheel skid
    3. Use only the front brake for maximum stopping power
    4. Apply both brakes progressively, with more force on the front Correct answer.

    Explanation

    Both brakes should be applied progressively, with the front brake providing most of the stopping power as weight transfers forward. Sudden application can lock a wheel. Downshifting alone does not stop the motorcycle quickly.

  20. Question 20Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is riding at night and meets an oncoming vehicle with bright headlights. To reduce glare, the rider should:

    1. Speed up to pass the vehicle quickly
    2. Look toward the right edge of the lane Correct answer.
    3. Stare directly at the oncoming headlights
    4. Close one eye until the vehicle passes

    Explanation

    Looking toward the right edge of the lane helps the rider maintain lane position while avoiding direct glare. Staring at the lights temporarily impairs night vision. Speeding up increases risk.

  21. Question 21Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is travelling on a highway and wants to change lanes. Which sequence is correct?

    1. Check mirrors, move, then signal
    2. Honk, then change lanes without signalling
    3. Signal, check mirrors and blind spot, then move when clear Correct answer.
    4. Signal and move immediately without checking

    Explanation

    A lane change requires signalling, checking mirrors and the blind spot, and moving only when the lane is clear. Signalling without checking does not ensure safety. Mirrors alone may not reveal a vehicle in the blind spot.

  22. Question 22Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is approaching a sharp curve at night on an unfamiliar road. Which action best manages the risk?

    1. Use the centre line to widen the curve
    2. Slow before the curve so the bike can be controlled through it Correct answer.
    3. Turn on the high beam and maintain speed
    4. Enter at the posted speed and adjust after seeing the curve

    Explanation

    Speed should be set before entering a curve so the motorcycle can be controlled throughout it. Night riding on unfamiliar roads limits how far ahead the rider can see. Adjusting after entering may be too late.

  23. Question 23Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is riding in a strong crosswind on an open highway. Which technique best maintains control?

    1. Ride close to the centre line to avoid wind gusts
    2. Reduce speed and allow room for the bike to be pushed sideways Correct answer.
    3. Increase speed to push through the gusts
    4. Ride with one hand to absorb the wind

    Explanation

    Reducing speed and leaving lateral room lets the rider absorb gusts without drifting into another lane. Grip the bars firmly with both hands. Anticipating gusts near open areas and large vehicles helps.

  24. Question 24Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is following a vehicle that suddenly brakes hard. The rider had been maintaining a two-second gap. Why is a larger gap recommended for motorcycles?

    1. A larger gap gives more time to see and react to hazards Correct answer.
    2. Larger gaps reduce fuel consumption
    3. Motorcycles stop more slowly than cars
    4. Cars are required to yield to motorcycles

    Explanation

    A larger following gap provides more time to perceive hazards and react, which matters because motorcycles have less crash protection. It also improves the rider's view of the road ahead. Two seconds is a minimum in good conditions.

  25. Question 25Alberta traffic laws and rules of the road applicable to motorcycles

    A rider is stopped behind a large vehicle at a red light. To reduce risk if the vehicle rolls backward, the rider should:

    1. Stop directly behind the vehicle's rear bumper
    2. Stop in the vehicle's centre mirror view
    3. Stop with the front wheel touching the vehicle
    4. Stop off to one side with an escape path Correct answer.

    Explanation

    Stopping slightly to one side keeps the rider visible and provides an escape route if the vehicle rolls back. Leaving space behind the vehicle also reduces the chance of being trapped. Being directly behind limits options.

  26. Question 26Alberta traffic laws and rules of the road applicable to motorcycles

    In Alberta, a motorcycle rider is required to wear a helmet that meets approved safety standards:

    1. Only on highways outside city limits
    2. At all times while the motorcycle is in motion Correct answer.
    3. Only when carrying a passenger
    4. Only when travelling faster than 60 km/h

    Explanation

    Alberta law requires every motorcycle rider and passenger to wear a properly fastened, approved helmet whenever the motorcycle is being operated on a road. There is no speed or location exception for helmet use.

  27. Question 27Alberta traffic laws and rules of the road applicable to motorcycles

    When a motorcycle rider is preparing to turn or change lanes, the rider should signal:

    1. At the same moment the turn begins
    2. After completing the manoeuvre
    3. Well in advance of the manoeuvre Correct answer.
    4. Only if other traffic is visible nearby

    Explanation

    Signals must be given early enough to warn other road users of the intended movement. Signalling only as the turn begins gives others little time to react.

  28. Question 28Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is approaching a railway crossing with the signal lights flashing and the gate lowered. The rider must:

    1. Drive around the gate carefully
    2. Stop and wait until the signals stop and the gate is raised Correct answer.
    3. Sound the horn and continue across
    4. Proceed if the rider can see no train approaching

    Explanation

    Flashing lights and a lowered gate mean a train is approaching and the crossing must not be entered. The rider must remain stopped until the signals are deactivated and the gate is fully raised.

  29. Question 29Alberta traffic laws and rules of the road applicable to motorcycles

    In Alberta, a motorcycle rider who is convicted of impaired driving will:

    1. Receive only a warning for a first offence
    2. Face the same impaired driving penalties as other drivers Correct answer.
    3. Lose only the motorcycle endorsement for 30 days
    4. Pay a reduced fine because a motorcycle is lighter

    Explanation

    Impaired driving laws apply equally to all motor vehicles, including motorcycles. Penalties such as licence suspension, fines, and vehicle seizure apply to motorcycle riders just as they do to other drivers.

  30. Question 30Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding at night and the motorcycle's headlight fails. The rider should:

    1. Use the turn signal as a substitute headlight
    2. Stop as soon as it is safe and not continue until the light is repaired Correct answer.
    3. Continue at a reduced speed using a flashlight
    4. Ride on the shoulder to the destination

    Explanation

    A motorcycle must have a functioning white headlight when operated at night. Continuing without it is unsafe and contrary to equipment requirements, so the rider should stop in a safe place and have the light repaired.

  31. Question 31Alberta traffic laws and rules of the road applicable to motorcycles

    When a motorcycle is carrying a passenger in Alberta, the passenger must:

    1. Hold a Class 6 licence
    2. Wear a helmet that meets approved standards Correct answer.
    3. Be at least 18 years old
    4. Sit facing sideways

    Explanation

    Passengers on a motorcycle are subject to the same helmet requirement as the rider. The helmet must be approved and properly fastened.

  32. Question 32Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is approaching an intersection where the traffic light is green but the intersection is blocked by queued vehicles. The rider should:

    1. Use the shoulder to pass the queued vehicles
    2. Enter the intersection and wait in the middle
    3. Sound the horn until the vehicles move
    4. Stop before the intersection and wait until there is space to clear it Correct answer.

    Explanation

    A rider should not enter an intersection unless there is enough space to clear it completely. Blocking the intersection is an offence and creates a hazard.

  33. Question 33Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a road with a solid yellow line on the rider's side. This line means:

    1. The rider may use the opposing lane to pass slow vehicles
    2. The line marks a bicycle lane
    3. Passing is permitted when the way is clear
    4. Passing is prohibited Correct answer.

    Explanation

    A solid yellow line on the rider's side of the centre line indicates that passing is not permitted. Yellow lines separate traffic moving in opposite directions.

  34. Question 34Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in the left lane of a multi-lane highway. To move to the right lane, the rider should:

    1. Change lanes without signalling if no vehicle is visible
    2. Check mirrors, signal, shoulder check, and change lanes when safe Correct answer.
    3. Signal and change lanes immediately
    4. Rely only on the mirrors before moving

    Explanation

    A lane change requires a mirror check, a signal, a shoulder check for blind spots, and a smooth movement only when the lane is clear. All steps are necessary to manage risk.

  35. Question 35Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in the centre portion of a lane where oil and debris tend to collect. The rider should generally:

    1. Ride in the centre to be most visible
    2. Ride in the left or right portion of the lane to avoid the slick centre Correct answer.
    3. Ride close to the curb
    4. Ride on the painted lane markings

    Explanation

    The centre of a lane often accumulates oil drips and debris, reducing traction. Riding in the left or right portion keeps the tires on cleaner pavement and improves the rider's view and visibility.

  36. Question 36Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a road with a posted speed limit of 50 km/h. The rider's speed should be:

    1. Up to 60 km/h to keep with traffic
    2. Whatever speed the rider feels comfortable with
    3. Exactly 50 km/h at all times
    4. At or below 50 km/h and appropriate for conditions Correct answer.

    Explanation

    The posted limit is the maximum permitted speed in good conditions. A rider must not exceed it and must reduce speed when conditions such as weather or traffic require.

  37. Question 37Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in a lane next to a row of parked cars. To reduce risk, the rider should:

    1. Ride on the sidewalk to avoid the parked cars
    2. Watch for doors opening and leave space beside parked vehicles Correct answer.
    3. Ride close to the parked cars to keep the lane clear
    4. Assume drivers will check before opening doors

    Explanation

    Occupants of parked vehicles may open doors without checking, creating a serious hazard for motorcyclists. Leaving space and scanning for movement inside parked cars reduces the chance of a collision.

  38. Question 38Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding behind a large truck that is approaching a railway crossing. The rider should:

    1. Increase following distance and be prepared to stop Correct answer.
    2. Pass the truck before the crossing
    3. Follow closely to cross the tracks at the same time
    4. Rely on the truck driver to warn of a train

    Explanation

    Large vehicles may stop unexpectedly at railway crossings, and a rider following closely has little time to react. Increasing the gap and preparing to stop improves safety.

  39. Question 39Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding at night and the motorcycle's headlight beam is aimed too high, dazzling oncoming drivers. The rider should:

    1. Use only the parking lights
    2. Adjust the headlight aim to the proper level Correct answer.
    3. Ride with the headlight off in lit areas
    4. Switch to high beam to see better

    Explanation

    A headlight aimed too high creates glare for oncoming traffic and reduces the rider's own road illumination. The correct fix is to adjust the aim to the manufacturer's specification.

  40. Question 40Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in traffic and needs to stop quickly. The rider should apply:

    1. Both brakes smoothly and progressively Correct answer.
    2. Only the front brake
    3. Only the rear brake
    4. The rear brake first, then the front brake hard

    Explanation

    Both brakes should be applied together and progressively to use the available traction without locking either wheel. The front brake provides most stopping power, but the rear brake adds stability.

  41. Question 41Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a gravel road. Compared with paved roads, the rider should:

    1. Lean sharply in curves
    2. Reduce speed and use smooth, gentle inputs Correct answer.
    3. Increase speed to maintain momentum
    4. Use the front brake hard for turns

    Explanation

    Gravel reduces traction, so lower speed and smooth control inputs help maintain stability. Abrupt braking or steering is more likely to cause a loss of control on loose surfaces.

  42. Question 42Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in a group and the group is approaching a stop sign. The safest practice is for the group to:

    1. Stop only the last rider in the group
    2. Stop as a single unit with the leader making the decision
    3. Wave the group through without stopping
    4. Have each rider stop individually and proceed when safe Correct answer.

    Explanation

    Each rider must obey the stop sign and ensure the way is clear before proceeding. Group riding does not exempt any rider from traffic control devices.

  43. Question 43Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in a lane and a vehicle ahead is straddling the centre line. The rider should:

    1. Assume the vehicle will move over and continue at the same speed
    2. Flash the headlight and maintain speed
    3. Increase space and be prepared for the vehicle to move unpredictably Correct answer.
    4. Pass the vehicle immediately on the right

    Explanation

    A vehicle straddling the centre line may be about to turn or may be driven erratically. Increasing following distance and preparing for sudden movement gives the rider time to react.

  44. Question 44Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a road with a broken white line separating two lanes travelling in the same direction. This line means:

    1. Lane changing is permitted when safe Correct answer.
    2. Lane changing is prohibited
    3. The lanes are for opposing traffic
    4. The rider must stay in the left lane

    Explanation

    A broken white line separates lanes of traffic moving in the same direction and indicates that lane changes are permitted when safe. White lines mark traffic moving in the same direction.

  45. Question 45Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a highway and the motorcycle's chain breaks. The rider should:

    1. Tie the chain up and keep riding
    2. Coast in neutral to a service station
    3. Continue at a low speed to the next exit
    4. Safely move off the road and stop Correct answer.

    Explanation

    A broken chain removes power to the rear wheel and can lock or damage components. The rider should safely move off the roadway and stop rather than continue riding.

  46. Question 46Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in the left lane of a four-lane road and a vehicle in the right lane is signalling to move into the rider's lane. The rider should:

    1. Sound the horn and maintain position
    2. Move into the oncoming lane to make room
    3. Speed up to block the lane change
    4. Adjust speed and space to allow the lane change if safe Correct answer.

    Explanation

    When another driver signals a lane change, the rider should help the movement proceed safely if possible by adjusting speed and space. Blocking or ignoring the signal increases conflict.

  47. Question 47Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in a lane where the pavement is wet and the rider needs to turn. The rider should:

    1. Accelerate through the turn to maintain traction
    2. Lean sharply to shorten the turn
    3. Brake hard while leaning into the turn
    4. Reduce speed before the turn and use smooth inputs Correct answer.

    Explanation

    On wet pavement, traction is reduced, so speed should be reduced before the turn and all inputs should be smooth. Braking or accelerating abruptly while leaned over can cause a slide.

  48. Question 48Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding at night and the rider's visor becomes smeared with insects. The safest action is to:

    1. Use the headlight high beam to see through the smear
    2. Ride with the visor raised at highway speed
    3. Continue riding and wipe the visor with a gloved hand while moving
    4. Stop in a safe place and clean the visor Correct answer.

    Explanation

    A smeared visor severely reduces vision, especially at night. The rider should stop in a safe location and clean the visor rather than attempt to clean it while riding.

  49. Question 49Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding in a lane and a large truck ahead begins to slow for a turn. The rider should:

    1. Move into the truck's blind spot to be seen
    2. Hold back and allow the truck to complete the turn Correct answer.
    3. Pass the truck on the right as it turns
    4. Follow closely to use the truck's draft

    Explanation

    Large trucks need extra space to turn and may swing wide. Holding back keeps the rider clear of the truck's path and out of its blind spots.

  50. Question 50Alberta traffic laws and rules of the road applicable to motorcycles

    A motorcycle rider is riding on a road with a posted speed limit of 80 km/h and the rider's speed is 80 km/h. The rider sees a sharp curve ahead with a recommended speed sign of 50 km/h. The rider should:

    1. Brake hard while in the curve
    2. Maintain 80 km/h because it is the posted limit
    3. Accelerate to stabilize the motorcycle
    4. Reduce speed to about the recommended speed before the curve Correct answer.

    Explanation

    A recommended speed sign indicates a safe speed for the curve, which may be well below the posted limit. The rider should slow before entering the curve so the motorcycle is stable through it.

  51. Question 51Safe motorcycle riding practices and hazard awareness

    When riding at night, which practice best helps you see the road ahead while limiting glare from oncoming traffic?

    1. Turn on your high beam whenever a vehicle approaches
    2. Look toward the right edge of your lane and use your low beam Correct answer.
    3. Look directly at the headlights of oncoming vehicles
    4. Ride closer to the centre line to use other vehicles' lights

    Explanation

    At night, aim your gaze toward the right edge of your lane so oncoming headlights do not blind you, and keep the low beam on when traffic is present. High beams must be dimmed for oncoming or closely followed vehicles, and staring at headlights temporarily destroys night vision.

  52. Question 52Safe motorcycle riding practices and hazard awareness

    What is the recommended following distance for a motorcycle in normal conditions?

    1. Three car lengths at any speed
    2. Half a car length behind the vehicle ahead
    3. Two seconds behind the vehicle ahead Correct answer.
    4. One second behind the vehicle ahead

    Explanation

    A minimum two-second following distance gives you time to react and stop, and it should be increased in poor weather or at higher speeds. Fixed distances in car lengths do not account for speed and are unreliable.

  53. Question 53Safe motorcycle riding practices and hazard awareness

    Where should you position your motorcycle within a lane when riding on a highway?

    1. Always in the centre of the lane
    2. Directly in line with the vehicle ahead
    3. Wherever you are most visible and have the best escape path Correct answer.
    4. Always in the left portion next to the centre line

    Explanation

    Lane position should be chosen for visibility to others and for the best escape route, and it changes with traffic and road conditions. There is no single fixed position that is always correct.

  54. Question 54Safe motorcycle riding practices and hazard awareness

    What should you do if you must ride over a metal bridge deck or grating that is wet?

    1. Lean the bike sharply to change lanes
    2. Reduce speed and avoid sudden steering or braking inputs Correct answer.
    3. Apply the front brake firmly while crossing
    4. Increase speed to cross quickly

    Explanation

    Wet metal surfaces offer very little traction, so you should slow down before the surface and cross smoothly without abrupt braking, acceleration, or steering. Sudden inputs on a low-traction surface can cause a loss of control.

  55. Question 55Safe motorcycle riding practices and hazard awareness

    When entering a curve, when should you complete most of your braking?

    1. Only if you see gravel mid-curve
    2. After you have leaned into the curve
    3. While leaned over at the apex
    4. Before you enter the curve Correct answer.

    Explanation

    Braking should be finished before the curve so the tyres have traction available for cornering. Braking while leaned over reduces the grip available for turning and can cause a skid.

  56. Question 56Safe motorcycle riding practices and hazard awareness

    What is the primary reason to check your mirrors and blind spots before changing lanes?

    1. To detect vehicles hidden in areas your mirrors do not show Correct answer.
    2. To confirm your turn signal is working
    3. To decide whether to use the horn
    4. To check the condition of your rear tyre

    Explanation

    Mirrors leave blind spots, especially beside and slightly behind the rider, so a shoulder check is needed to confirm the space is clear. A signal alone does not guarantee the lane is safe to enter.

  57. Question 57Safe motorcycle riding practices and hazard awareness

    How does riding over a painted crosswalk or lane marking in the rain affect traction?

    1. Traction is improved because the paint seals the surface
    2. Traction is reduced because the paint can be slippery when wet Correct answer.
    3. Traction is only affected on hot days
    4. Traction is unchanged from dry pavement

    Explanation

    Painted road markings, especially when wet, can be much slicker than the surrounding pavement. You should avoid hard braking or sharp turning while crossing them in wet conditions.

  58. Question 58Safe motorcycle riding practices and hazard awareness

    What is the best way to reduce the risk of a collision with a vehicle turning left across your path?

    1. Speed up to pass before the turn is completed
    2. Move to the far right of your lane and continue at the same speed
    3. Sound the horn and maintain your speed
    4. Slow down, cover the brakes, and be ready to stop Correct answer.

    Explanation

    Left-turning vehicles are a leading cause of motorcycle collisions, so you should reduce speed, cover the controls, and prepare to stop. Being visible and predictable gives you time to react if the driver misjudges your approach.

  59. Question 59Safe motorcycle riding practices and hazard awareness

    When riding in a group, what formation is generally recommended on a straight road?

    1. A single file with no gaps
    2. Side by side in the same lane
    3. A staggered formation with space between riders Correct answer.
    4. Clustered tightly together

    Explanation

    A staggered formation keeps riders spaced so each has room to react while keeping the group compact. It should convert to single file in curves or tight spaces.

  60. Question 60Safe motorcycle riding practices and hazard awareness

    What does countersteering mean when riding a motorcycle at road speed?

    1. Applying the rear brake while turning
    2. Pushing the handlebar on the side you want to turn toward Correct answer.
    3. Leaning the body while keeping the bars straight
    4. Pulling both handlebar grips toward you

    Explanation

    At speed, pushing the handlebar on the side you want to turn initiates the lean that turns the motorcycle. This is the normal way to steer a motorcycle above walking pace.

  61. Question 61Safe motorcycle riding practices and hazard awareness

    How should you adjust your riding when the road surface is wet?

    1. Brake harder and later than usual
    2. Reduce speed and increase following distance Correct answer.
    3. Lean more sharply in corners
    4. Increase speed to get through the rain faster

    Explanation

    Wet roads reduce traction and lengthen stopping distances, so you should slow down and leave a larger gap. Smooth control inputs help maintain grip.

  62. Question 62Safe motorcycle riding practices and hazard awareness

    What is the main danger of riding in a vehicle's blind spot?

    1. The vehicle will use more fuel
    2. Your engine may overheat
    3. The driver may change lanes into your path without seeing you Correct answer.
    4. Your headlight may fail

    Explanation

    Drivers have blind spots beside and behind their vehicles where a motorcycle can be invisible. You should avoid lingering in those areas and either drop back or move ahead.

  63. Question 63Safe motorcycle riding practices and hazard awareness

    When approaching a railway crossing with no gate, what should you do?

    1. Speed up to cross before a train arrives
    2. Stop on the tracks to check for trains
    3. Follow the vehicle ahead closely across the tracks
    4. Slow down, look both ways, and cross only when clear Correct answer.

    Explanation

    At an uncontrolled crossing you should reduce speed, look and listen for trains, and cross only when the way is clear. Never stop on the tracks.

  64. Question 64Safe motorcycle riding practices and hazard awareness

    What is the safest response when a strong crosswind hits you while riding?

    1. Grip the bars tightly and brake hard
    2. Accelerate to push through the gust
    3. Ignore it and maintain speed
    4. Lean into the wind and reduce speed smoothly Correct answer.

    Explanation

    In a crosswind, lean slightly into the wind and reduce speed smoothly to stay stable. Sudden braking or acceleration can upset the motorcycle.

  65. Question 65Safe motorcycle riding practices and hazard awareness

    Why should you avoid riding directly over the centre of a lane that may have oil drips?

    1. The centre is always the smoothest surface
    2. The centre has better drainage than the edges
    3. The centre is reserved for motorcycles
    4. The centre is where vehicles drip oil, reducing traction Correct answer.

    Explanation

    Vehicles often drip oil and fluids in the centre of a lane, especially at intersections and stops. Those deposits are slippery, particularly when wet, so a different lane position is safer.

  66. Question 66Safe motorcycle riding practices and hazard awareness

    What should you do if your front tyre begins to skid while braking?

    1. Apply the throttle
    2. Turn the handlebars sharply
    3. Release the front brake and reapply it smoothly Correct answer.
    4. Apply more front brake to stop faster

    Explanation

    If the front tyre skids, releasing the brake lets the wheel regain grip so you can reapply pressure smoothly. Continued hard braking keeps the wheel locked and risks a fall.

  67. Question 67Safe motorcycle riding practices and hazard awareness

    What does the 'three-second rule' help a rider determine?

    1. A safe following distance from the vehicle ahead Correct answer.
    2. How long to signal before a turn
    3. The time needed to check mirrors
    4. How long to wait at a stop sign

    Explanation

    The three-second rule is a method for measuring a safe following gap by counting the time between the vehicle ahead passing a fixed point and you reaching it. It should be increased in poor conditions.

  68. Question 68Safe motorcycle riding practices and hazard awareness

    When is it most important to increase your following distance beyond the normal gap?

    1. On a clear, dry day at noon
    2. In heavy traffic, rain, or at night Correct answer.
    3. When the road is empty
    4. When riding in a group

    Explanation

    Poor weather, darkness, and dense traffic all increase stopping distances and reduce visibility, so a larger following gap is needed. Clear, empty roads allow the normal gap.

  69. Question 69Safe motorcycle riding practices and hazard awareness

    What is the recommended way to carry cargo on a motorcycle?

    1. Hang it from the handlebars
    2. Carry it in one hand while riding
    3. Strap it high on the rear seat
    4. Secure it low and close to the centre of the motorcycle Correct answer.

    Explanation

    Cargo should be secured low and near the centre so it does not affect balance or steering. Loose or high-mounted loads can shift and cause a loss of control.

  70. Question 70Safe motorcycle riding practices and hazard awareness

    What should you do before riding through a large puddle of unknown depth?

    1. Apply the front brake while in the water
    2. Slow down and check for hidden hazards or choose another route Correct answer.
    3. Close your eyes briefly and hold the bars tightly
    4. Accelerate to skim across it

    Explanation

    Unknown-depth water can hide potholes, debris, or a deep drop, so slowing down and assessing the crossing is safest. Braking hard or accelerating in deep water risks a loss of control.

  71. Question 71Safe motorcycle riding practices and hazard awareness

    Why should you avoid following a large truck too closely?

    1. It blocks your view and leaves little room to react Correct answer.
    2. It uses more fuel than cars
    3. It has no turn signals
    4. It always drives below the speed limit

    Explanation

    Large trucks block forward visibility and have long stopping distances, so a close following position hides hazards and reduces your reaction time. Staying back also keeps you out of the driver's blind spots.

  72. Question 72Safe motorcycle riding practices and hazard awareness

    What is the best way to be seen by other drivers when riding during the day?

    1. Ride faster than surrounding traffic
    2. Ride only in the centre of the lane
    3. Wear bright or reflective clothing and keep your headlight on Correct answer.
    4. Use hand signals instead of turn signals

    Explanation

    Bright or reflective gear and a headlight on improve your visibility to other drivers. Being conspicuous helps prevent collisions caused by drivers failing to notice a motorcycle.

  73. Question 73Safe motorcycle riding practices and hazard awareness

    What should you do if you are being followed too closely by another vehicle?

    1. Speed up well beyond the limit
    2. Gradually increase your following distance and let them pass Correct answer.
    3. Weave within the lane
    4. Brake sharply to warn the driver

    Explanation

    When tailgated, opening space ahead and allowing the driver to pass reduces the risk of a rear-end collision. Sudden braking or weaving can provoke a crash.

  74. Question 74Safe motorcycle riding practices and hazard awareness

    What is the purpose of a pre-ride inspection of tyres, brakes, and lights?

    1. To catch problems that could cause a crash before you ride Correct answer.
    2. To improve fuel economy
    3. To warm up the engine
    4. To satisfy insurance requirements only

    Explanation

    A pre-ride check identifies defects such as low tyre pressure, worn brakes, or faulty lights that could lead to a crash. Catching these before riding is a core safe-riding practice.

  75. Question 75Safe motorcycle riding practices and hazard awareness

    When you must brake in an emergency where your wheels are likely to lock, what is the recommended technique for a motorcycle with conventional brakes?

    1. Apply both brakes firmly and smoothly without locking the wheels Correct answer.
    2. Release both brakes and coast
    3. Use only the rear brake
    4. Use only the front brake

    Explanation

    Smooth, firm application of both brakes gives the shortest stop while avoiding wheel lockup. Locked wheels skid and reduce control, so progressive pressure is key.

  76. Question 76Safe motorcycle riding practices and hazard awareness

    What is the main reason to keep both hands on the handlebars whenever the motorcycle is moving?

    1. It reduces the noise from the exhaust
    2. It prevents the mirrors from vibrating
    3. It improves steering control and lets you brake or swerve quickly Correct answer.
    4. It keeps the engine oil circulating properly

    Explanation

    Both hands on the bars give you full authority over steering, throttle and braking, which you need for sudden hazards. Removing a hand lengthens your reaction time and reduces control.

  77. Question 77Safe motorcycle riding practices and hazard awareness

    Why should you ride with your headlight on during the day?

    1. To charge the battery faster
    2. To signal that you intend to turn
    3. To see the road surface more clearly at noon
    4. To make the motorcycle more noticeable to other road users Correct answer.

    Explanation

    A lit headlight creates a small, bright point of light that helps oncoming and crossing drivers notice the narrow profile of a motorcycle. It is a visibility aid, not a signal of intention.

  78. Question 78Safe motorcycle riding practices and hazard awareness

    What is the safest position within your lane when a vehicle ahead is stopped and waiting to turn left while you approach?

    1. Stay directly behind the vehicle and close the gap
    2. Move to the centre of the lane and hold speed
    3. Move to the left portion of the lane and accelerate
    4. Move toward the right portion of your lane and slow down Correct answer.

    Explanation

    Shifting right widens the space between you and the turning vehicle and keeps you out of the path it may sweep through. Slowing gives you time to stop if the driver turns across you.

  79. Question 79Safe motorcycle riding practices and hazard awareness

    When riding at night, how should you adjust your speed compared with daytime riding on the same road?

    1. Reduce speed so you can stop within the distance your headlight lights up Correct answer.
    2. Match the speed of the vehicle ahead regardless of visibility
    3. Increase speed to spend less time in the dark
    4. Keep the same speed because the speed limit does not change

    Explanation

    At night your visible stopping distance is limited by the headlight beam, so you must be able to stop within that lit distance. Riding faster than your lights allow means hazards appear too late.

  80. Question 80Safe motorcycle riding practices and hazard awareness

    What is the main hazard of riding over a metal bridge deck or steel grating when it is wet?

    1. The tyres will overheat from the contact
    2. The headlight beam will reflect back at you
    3. The engine will lose power on the metal
    4. Traction is sharply reduced and the surface can cause the bike to wander Correct answer.

    Explanation

    Wet steel offers very little grip, and grating can also steer the front wheel along its grooves. Cross such surfaces upright, at a steady speed, and avoid braking or turning hard on them.

  81. Question 81Safe motorcycle riding practices and hazard awareness

    What should you do if a front tyre suddenly goes flat while you are riding at highway speed?

    1. Ease off the throttle, hold the bars firmly and slow gradually without hard braking Correct answer.
    2. Accelerate to stabilise the motorcycle
    3. Apply the front brake firmly to stop quickly
    4. Pull the clutch in and turn sharply off the road

    Explanation

    A deflating front tyre makes steering heavy and unstable, so you should avoid sudden inputs. Rolling off the throttle and letting the bike slow while gripping the bars keeps it upright until you can stop safely.

  82. Question 82Safe motorcycle riding practices and hazard awareness

    Why is it important to scan well ahead rather than watching only the vehicle directly in front?

    1. It reduces engine vibration at speed
    2. It gives you time to plan an escape path before a hazard reaches you Correct answer.
    3. It lets you ignore your mirrors
    4. It keeps your eyes protected from wind

    Explanation

    Looking far ahead lets you identify developing hazards early and choose a path or speed change in advance. Fixating on the vehicle ahead leaves no time to react when something unexpected happens.

  83. Question 83Safe motorcycle riding practices and hazard awareness

    What is the recommended way to cross tram or streetcar rails that run across your path?

    1. Brake hard while the front wheel is on the rail
    2. Cross as close to a right angle as possible Correct answer.
    3. Slow to a crawl and turn along the rail
    4. Cross at a shallow angle to smooth the bump

    Explanation

    Crossing rails at a large angle reduces the chance of the tyre being caught and deflected along the groove. Wet rails are especially slippery, so keep the bike upright and avoid braking on them.

  84. Question 84Safe motorcycle riding practices and hazard awareness

    What is the main risk of riding with your visor or goggles fogged up?

    1. The engine will run hotter
    2. Your hearing is reduced
    3. Your helmet becomes heavier on your head
    4. Your view of hazards and mirrors is blocked, delaying your reactions Correct answer.

    Explanation

    Reduced vision means hazards, signals and mirror checks are missed until too late. Clear your visor or use an anti-fog treatment before riding in cold or damp conditions.

  85. Question 85Safe motorcycle riding practices and hazard awareness

    How should you position your motorcycle when stopping behind another vehicle at a red light?

    1. Directly in line and close behind its bumper
    2. Beside the vehicle in the oncoming lane
    3. Offset to one side of the vehicle ahead with an escape route Correct answer.
    4. Centred in the lane with the front wheel touching the line

    Explanation

    Stopping offset gives you room to move if a vehicle behind fails to stop, and it keeps you visible in the driver's mirror. Leave enough gap to pull around the vehicle if needed.

  86. Question 86Safe motorcycle riding practices and hazard awareness

    What does it mean when a rider says the motorcycle is 'target fixated'?

    1. The bike is parked in a designated spot
    2. The rider's gaze locks on a hazard and the bike tends to steer toward it Correct answer.
    3. The rider is following a planned route precisely
    4. The motorcycle has a factory-set steering damper

    Explanation

    People tend to steer where they look, so staring at a pothole or obstacle can draw the bike toward it. Train your eyes to look at the escape path instead.

  87. Question 87Safe motorcycle riding practices and hazard awareness

    What is the safest way to handle a curve that tightens unexpectedly as you ride through it?

    1. Grab the front brake hard and stand the bike up
    2. Chop the throttle and coast upright
    3. Straighten the bike and run wide
    4. Look through the curve and apply a smooth, gradual lean to tighten your line Correct answer.

    Explanation

    Looking through the turn keeps your path visible and lets you add lean smoothly to follow the tightening curve. Abrupt braking or standing the bike up mid-corner usually sends you wide.

  88. Question 88Safe motorcycle riding practices and hazard awareness

    Why should you avoid riding with your arms locked straight?

    1. Locked arms increase fuel consumption
    2. Locked arms make the headlight aim too high
    3. Locked arms reduce your ability to steer smoothly and absorb bumps Correct answer.
    4. Locked arms prevent the throttle from closing

    Explanation

    Slightly bent arms act as shock absorbers and allow precise, relaxed steering inputs. Straight, rigid arms transmit bumps to the bars and make the bike harder to control.

  89. Question 89Safe motorcycle riding practices and hazard awareness

    When riding in heavy rain, why should you avoid the painted areas at intersections?

    1. Paint attracts oil from other vehicles
    2. Paint raises the road temperature under the tyres
    3. Paint reflects your headlight into your eyes
    4. Paint becomes very slippery when wet and reduces tyre grip Correct answer.

    Explanation

    Road paint is smoother than asphalt and offers much less grip when wet, especially while leaning or braking. Cross painted lines as upright and smoothly as you can.

  90. Question 90Safe motorcycle riding practices and hazard awareness

    What should you do if an oncoming vehicle's headlights are dazzling you at night?

    1. Flash your high beam continuously
    2. Look directly at the lights to judge the distance
    3. Look toward the right edge of your lane and slow down Correct answer.
    4. Speed up to pass the vehicle sooner

    Explanation

    Shifting your gaze to the right edge keeps you on your path without staring into the glare. Slowing gives you more time to react while your eyes recover.

  91. Question 91Safe motorcycle riding practices and hazard awareness

    What is the main danger of riding with your feet not properly on the footpegs?

    1. The exhaust will overheat
    2. You lose control and stability, especially over bumps or in a swerve Correct answer.
    3. The mirrors will misalign
    4. The chain will stretch

    Explanation

    Feet on the pegs are part of how you control and balance the motorcycle. Losing a footing over a bump or during a manoeuvre can cause a loss of control.

  92. Question 92Safe motorcycle riding practices and hazard awareness

    How should you handle a strong gust of wind from a passing large truck?

    1. Lean hard into the truck as it passes
    2. Brake sharply the moment you feel the gust
    3. Accelerate to outrun the gust
    4. Grip the bars firmly, expect the push, and stay relaxed in your lane Correct answer.

    Explanation

    Turbulence from a large vehicle can push you sideways suddenly, so a firm grip and a relaxed body let the bike absorb it. Anticipate the gust and hold your lane position.

  93. Question 93Safe motorcycle riding practices and hazard awareness

    What is the purpose of covering the front brake lever in traffic?

    1. It keeps the lever from getting cold
    2. It shortens the time needed to begin braking Correct answer.
    3. It improves fuel economy
    4. It prevents the throttle from sticking

    Explanation

    With your fingers resting over the lever, you can apply the brake without first moving your hand, saving reaction time. This matters most when traffic ahead may stop suddenly.

  94. Question 94Safe motorcycle riding practices and hazard awareness

    What should you do if your motorcycle begins to wobble or shake at high speed?

    1. Ease off the throttle and grip the bars firmly without fighting the wobble Correct answer.
    2. Accelerate hard to pull through it
    3. Apply the front brake as hard as possible
    4. Release the bars completely

    Explanation

    A wobble is worsened by abrupt inputs, so rolling off the throttle smoothly and holding the bars firmly lets the bike settle. Braking hard or accelerating can amplify the oscillation.

  95. Question 95Safe motorcycle riding practices and hazard awareness

    Why should you check your tyre pressure before a long ride with a passenger?

    1. Correct pressure and load settings keep handling and braking stable Correct answer.
    2. It prevents the chain from rusting
    3. It makes the exhaust quieter
    4. It increases the top speed

    Explanation

    Carrying a passenger changes the load on the tyres and suspension, so pressures and settings often need adjusting per the owner's manual. Incorrect pressure can make the bike unstable or reduce grip.

  96. Question 96Safe motorcycle riding practices and hazard awareness

    What is the safest way to deal with a deep patch of loose gravel on a paved road?

    1. Turn sharply to avoid it at the last moment
    2. Slow before it, keep the bike upright and ride through smoothly Correct answer.
    3. Brake hard while the front wheel is in the gravel
    4. Accelerate through it to lighten the front

    Explanation

    Loose gravel reduces grip and can deflect the front wheel, so reduce speed beforehand and cross it upright with smooth inputs. Braking or turning on the gravel itself risks a slide.

  97. Question 97Safe motorcycle riding practices and hazard awareness

    What is the main reason to avoid riding between two lanes of moving traffic?

    1. There is no escape space if a vehicle changes lanes into you Correct answer.
    2. It makes your headlight less visible
    3. It is too cold between the lanes
    4. It increases tyre wear

    Explanation

    When you are between lanes, a driver on either side may move over without seeing you, and you have nowhere to go. Maintain a full lane position with space on both sides.

  98. Question 98Safe motorcycle riding practices and hazard awareness

    What should you do if your rear tyre starts to skid during braking?

    1. Keep the front brake steady and ease off the rear brake Correct answer.
    2. Turn the bars sharply to correct the slide
    3. Add more rear brake pressure
    4. Release both brakes completely

    Explanation

    A locked rear tyre slides, so easing off the rear brake lets it regain grip while the front continues to slow the bike. Releasing both brakes suddenly can cause a snap back into traction.

  99. Question 99Safe motorcycle riding practices and hazard awareness

    Why is it important to keep your helmet visor and windscreen clean?

    1. It makes the motorcycle faster
    2. It reduces engine noise
    3. It keeps the tyres cool
    4. Dirt and smears scatter light and can hide hazards Correct answer.

    Explanation

    A dirty visor scatters light, especially at night or in rain, and can obscure road features and mirrors. Clean it before riding so your view stays clear.

  100. Question 100Safe motorcycle riding practices and hazard awareness

    What is the best way to prepare for a hazard you can see developing far ahead, such as a car edging out of a driveway?

    1. Maintain speed and sound your horn repeatedly
    2. Close the gap so the driver sees you sooner
    3. Reduce speed and adjust your lane position to create a space cushion Correct answer.
    4. Move toward the vehicle to make eye contact

    Explanation

    Slowing and adjusting position gives you time and space to react if the driver pulls out. A space cushion lets you stop or swerve without relying on the other driver.

  101. Question 101Motorcycle controls, handling and vehicle familiarity

    On a motorcycle, which control operates the front brake?

    1. The lever on the left handlebar
    2. The lever on the right handlebar Correct answer.
    3. The pedal on the left footpeg
    4. The pedal on the right footpeg

    Explanation

    On standard motorcycles the front brake is applied with the right-hand lever, while the right foot pedal works the rear brake. Keeping these distinct matters because the front brake supplies most of the stopping force.

  102. Question 102Motorcycle controls, handling and vehicle familiarity

    The clutch lever on a typical motorcycle is located on which side?

    1. Right footpeg
    2. Left handlebar Correct answer.
    3. Right handlebar
    4. Left footpeg

    Explanation

    The clutch is operated by the lever on the left handlebar, allowing the rider to disengage engine power while the right hand stays on the throttle and front brake. This layout keeps throttle and front brake control available at all times.

  103. Question 103Motorcycle controls, handling and vehicle familiarity

    What is the primary function of the throttle twist grip?

    1. It applies the rear brake progressively
    2. It adjusts the suspension preload
    3. It selects the gear the transmission is in
    4. It controls engine power delivered to the rear wheel Correct answer.

    Explanation

    Rolling the throttle open increases engine output, which the drivetrain sends to the rear wheel to accelerate the motorcycle. Closing it reduces power and produces engine braking.

  104. Question 104Motorcycle controls, handling and vehicle familiarity

    On a motorcycle with a conventional sequential gearbox, what does pressing down on the shift lever normally do?

    1. Engages the clutch
    2. Selects a lower gear Correct answer.
    3. Selects a higher gear
    4. Applies the rear brake

    Explanation

    Most motorcycles use a sequential shift pattern in which pushing the lever down selects the next lower gear and lifting it selects the next higher gear. Riders learn this pattern so they can shift without looking down.

  105. Question 105Motorcycle controls, handling and vehicle familiarity

    Before a ride, a rider squeezes the front brake lever and it feels spongy and pulls almost to the grip. What does this most likely indicate?

    1. Normal operation for a cold brake
    2. The throttle cable is too tight
    3. The rear brake needs adjustment
    4. Air or a fluid problem in the brake system Correct answer.

    Explanation

    A firm lever that does not travel far is normal; a spongy lever that reaches the grip suggests air in the hydraulic line, low fluid, or a leak. The motorcycle should not be ridden until the brake system is inspected and corrected.

  106. Question 106Motorcycle controls, handling and vehicle familiarity

    What is the correct way to check drive chain tension on a motorcycle?

    1. Measure slack at the middle of the lower run against the manual's spec Correct answer.
    2. Check that the chain is tight enough that it cannot be moved at all
    3. Judge tension by the sound the chain makes while riding
    4. Pull the chain sideways at the rear sprocket as hard as possible

    Explanation

    Chain slack is measured at the midpoint of the lower chain run and compared with the manufacturer's specified range. Too tight stresses bearings and too loose risks the chain jumping or breaking.

  107. Question 107Motorcycle controls, handling and vehicle familiarity

    When should a rider check engine oil level on a motorcycle?

    1. Only when the oil warning light comes on
    2. While the bike is leaning on its side stand
    3. Immediately after a long ride while the engine is hot
    4. With the bike upright and level per the owner's manual procedure Correct answer.

    Explanation

    Oil level should be checked with the motorcycle held upright on level ground, following the manual's warm-up and waiting instructions. A leaning bike gives a false reading.

  108. Question 108Motorcycle controls, handling and vehicle familiarity

    A motorcycle's front brake provides most of its stopping power mainly because of which factor?

    1. Front tires have more tread depth
    2. The rear brake is only for parking
    3. The front brake disc is always larger than the rear
    4. Weight transfer loads the front tire during braking Correct answer.

    Explanation

    When a motorcycle decelerates, weight shifts forward, increasing load and therefore traction on the front tire. That added grip lets the front brake contribute the majority of stopping force.

  109. Question 109Motorcycle controls, handling and vehicle familiarity

    What is the purpose of the friction zone when starting from a stop?

    1. To disengage the clutch completely while accelerating
    2. To smoothly transfer engine power to the rear wheel as the clutch engages Correct answer.
    3. To hold the motorcycle stationary on a hill without brakes
    4. To lock the rear wheel for a quick launch

    Explanation

    The friction zone is the range of clutch lever travel where the clutch begins to engage and torque starts reaching the wheel. Using it gradually lets the rider pull away smoothly without stalling or lurching.

  110. Question 110Motorcycle controls, handling and vehicle familiarity

    A rider is coming to a stop from normal road speed. What is the recommended braking technique on a motorcycle with separate front and rear brakes?

    1. Use only the rear brake to keep the front tire planted
    2. Use only the front brake to avoid rear-wheel skid
    3. Apply the rear brake first and release the front entirely
    4. Apply both brakes together, with more force on the front Correct answer.

    Explanation

    Using both brakes together shares the braking load and uses the weight transfer that loads the front tire. The front brake can take more force because of that added traction.

  111. Question 111Motorcycle controls, handling and vehicle familiarity

    When should a rider use the turn signal when preparing to change lanes?

    1. At the same moment the motorcycle begins to move
    2. Only after the lane change is complete
    3. Early enough to give other drivers clear warning before moving Correct answer.
    4. Only if another vehicle is close behind

    Explanation

    Signalling early lets surrounding traffic anticipate the move and react. Signalling during or after the manoeuvre gives others no useful warning.

  112. Question 112Motorcycle controls, handling and vehicle familiarity

    What does the engine kill switch on the right handlebar do?

    1. Cuts ignition so the engine stops without releasing the handlebars Correct answer.
    2. Engages the starter motor
    3. Switches between high and low beam
    4. Locks the steering head

    Explanation

    The kill switch is a safety control that stops the engine immediately while the rider keeps both hands on the bars. It is commonly used in an emergency or when parking.

  113. Question 113Motorcycle controls, handling and vehicle familiarity

    What is the function of the motorcycle's steering lock?

    1. It secures the throttle in the closed position
    2. It prevents the handlebars from turning when parked Correct answer.
    3. It limits steering angle while riding at speed
    4. It locks the front brake lever in place

    Explanation

    The steering lock holds the front wheel turned to one side so the motorcycle cannot easily be rolled away or steered when parked. It is disengaged before riding.

  114. Question 114Motorcycle controls, handling and vehicle familiarity

    What does the clutch do when the lever is fully released?

    1. It disconnects the engine from the transmission
    2. It locks the gearbox in neutral
    3. It applies engine braking to the rear wheel
    4. It fully connects the engine to the transmission Correct answer.

    Explanation

    Releasing the clutch lever fully engages the clutch plates so engine power flows to the transmission. Squeezing the lever disengages it.

  115. Question 115Motorcycle controls, handling and vehicle familiarity

    A rider notices the motorcycle's front tire has a visible bulge in the sidewall. What is the appropriate action?

    1. Do not ride until the tire is inspected or replaced Correct answer.
    2. Reduce speed and continue the planned ride
    3. Ignore it if the tire holds air
    4. Lower tire pressure to soften the bulge

    Explanation

    A sidewall bulge indicates internal structural damage that can lead to a sudden blowout. The motorcycle should not be ridden until a qualified person inspects or replaces the tire.

  116. Question 116Motorcycle controls, handling and vehicle familiarity

    How does countersteering work at road speed on a motorcycle?

    1. Applying the rear brake causes the bike to steer
    2. Pushing the bar forward on the side you want to turn initiates a lean in that direction Correct answer.
    3. Leaning the body alone turns the bike without bar input
    4. Pulling both bars toward you tilts the bike into a turn

    Explanation

    At speed, a forward push on one bar momentarily steers the front wheel the other way, which leans the motorcycle and causes it to turn in the pushed direction. This is the normal way to initiate a turn at road speeds.

  117. Question 117Motorcycle controls, handling and vehicle familiarity

    Why should a rider avoid holding the front brake lever while riding over a slippery patch such as wet metal grating?

    1. The front brake overheats instantly on metal
    2. The lever can be pulled off the bar by vibration
    3. A locked front wheel causes an immediate loss of steering and balance Correct answer.
    4. The rear brake automatically disengages

    Explanation

    On a low-traction surface, a front wheel that locks loses its gyroscopic and steering stability, and a fall is very likely. Smooth inputs and reduced braking are needed on slippery surfaces.

  118. Question 118Motorcycle controls, handling and vehicle familiarity

    A motorcycle is parked facing downhill on a slope. What is the safest way to leave it parked?

    1. In neutral with only the side stand down
    2. In gear with the front wheel turned toward the curb and the rear brake held Correct answer.
    3. In gear with the front wheel turned away from the curb
    4. In neutral with the steering unlocked

    Explanation

    Leaving the bike in gear adds engine resistance, and turning the front wheel toward the curb means any roll pushes the tire into the curb. Holding the rear brake and using the stand keeps it secure.

  119. Question 119Motorcycle controls, handling and vehicle familiarity

    What is the purpose of the motorcycle's side stand safety switch?

    1. It engages the rear brake automatically
    2. It prevents riding off with the stand still down Correct answer.
    3. It disables the throttle at low speed
    4. It locks the front wheel when the stand is deployed

    Explanation

    The side stand switch cuts the engine if the transmission is put in gear while the stand is down, preventing a dangerous left-turn crash. It must be functioning for safe operation.

  120. Question 120Motorcycle controls, handling and vehicle familiarity

    When riding at night, which control setting should the rider use to avoid dazzling oncoming drivers?

    1. Hazard flashers
    2. Low beam Correct answer.
    3. Running lights only
    4. High beam

    Explanation

    Low beam directs light downward and forward without blinding oncoming traffic. High beam is reserved for unlit roads with no oncoming vehicles.

  121. Question 121Motorcycle controls, handling and vehicle familiarity

    A rider wants to slow the motorcycle using engine braking on a long descent. What should they do?

    1. Select a lower gear and ease off the throttle Correct answer.
    2. Squeeze the clutch and coast
    3. Hold the front brake continuously
    4. Shift to neutral to save fuel

    Explanation

    A lower gear raises engine speed and lets compression slow the bike, reducing reliance on the brakes on a long descent. Coasting or neutral removes engine braking and leaves the rider without control of speed.

  122. Question 122Motorcycle controls, handling and vehicle familiarity

    What does the tachometer on a motorcycle indicate?

    1. Road speed in kilometres per hour
    2. Engine speed in revolutions per minute Correct answer.
    3. Distance travelled since new
    4. Fuel level in the tank

    Explanation

    The tachometer shows engine revolutions per minute so the rider can shift before reaching the redline. Road speed is shown separately on the speedometer.

  123. Question 123Motorcycle controls, handling and vehicle familiarity

    Why should a rider avoid resting a foot on the rear brake pedal while cruising?

    1. It increases fuel economy
    2. It disengages the clutch
    3. It improves chain lubrication
    4. It can overheat the rear brake and cause it to drag Correct answer.

    Explanation

    Constant light pressure on the pedal keeps the rear brake partially applied, generating heat and reducing braking performance. The foot should rest on the peg, not on the pedal.

  124. Question 124Motorcycle controls, handling and vehicle familiarity

    What is the recommended hand position on the handlebars for good control?

    1. Keep the elbows locked straight
    2. Grip with the wrist slightly lower than the knuckles so the arm can follow the bar Correct answer.
    3. Grip only the bar ends with the fingertips
    4. Hold the bar with the wrist bent sharply upward

    Explanation

    A relaxed grip with the wrist near neutral lets the rider roll the throttle smoothly and steer without strain. Locked elbows or an awkward wrist reduce control and cause fatigue.

  125. Question 125Motorcycle controls, handling and vehicle familiarity

    A rider is preparing to ride and notices the throttle does not snap back when released. What should they do?

    1. Ignore it if the bike idles normally
    2. Have the throttle checked before riding Correct answer.
    3. Adjust the idle screw to compensate
    4. Ride slowly to the nearest shop

    Explanation

    A throttle that does not return freely is a serious safety fault because the engine may stay open unexpectedly. It must be corrected before the motorcycle is ridden.

  126. Question 126Motorcycle controls, handling and vehicle familiarity

    What is the primary purpose of the pre-ride check on a motorcycle?

    1. To confirm the machine is roadworthy before it is ridden Correct answer.
    2. To reset the trip meter for the journey
    3. To warm the engine to full operating temperature
    4. To test the horn volume for traffic use

    Explanation

    A pre-ride check is a quick systematic inspection of tires, controls, fluids, lights and chain so defects are found while the motorcycle is stationary. Problems caught before riding prevent breakdowns and crashes.

  127. Question 127Motorcycle controls, handling and vehicle familiarity

    Where is the front brake lever located on a typical motorcycle?

    1. On the left footpeg
    2. On the right handlebar Correct answer.
    3. On the right footpeg
    4. On the left handlebar

    Explanation

    The front brake is operated by the lever on the right handlebar, while the throttle is also on the right. The clutch lever and gear shifter are on the left side.

  128. Question 128Motorcycle controls, handling and vehicle familiarity

    Which control operates the rear brake on a motorcycle with a manual transmission?

    1. The lever at the right hand
    2. The lever at the left hand
    3. The pedal at the right foot Correct answer.
    4. The pedal at the left foot

    Explanation

    On a manual motorcycle the rear brake is applied by the foot pedal on the right side. The right hand lever works the front brake and the left foot works the gear shifter.

  129. Question 129Motorcycle controls, handling and vehicle familiarity

    What does the clutch lever allow the rider to do?

    1. Disconnect engine drive from the transmission Correct answer.
    2. Lock the steering when parked
    3. Change the stiffness of the suspension
    4. Adjust the idle speed of the engine

    Explanation

    Pulling the clutch lever separates the engine from the transmission so the rider can start, stop, and change gears smoothly. Releasing it reconnects drive to the rear wheel.

  130. Question 130Motorcycle controls, handling and vehicle familiarity

    What is the function of the motorcycle's mirrors when set correctly?

    1. To display the speed of following vehicles
    2. To show the area behind and beside the rider with minimal head movement Correct answer.
    3. To reflect the rider's own posture for training
    4. To replace the need for shoulder checks entirely

    Explanation

    Mirrors are adjusted so the rider can see behind and to the sides with only a glance, reducing blind spots. They supplement but never replace a shoulder check before a manoeuvre.

  131. Question 131Motorcycle controls, handling and vehicle familiarity

    What does the speedometer on a motorcycle indicate?

    1. The distance travelled since the last reset
    2. The engine speed in revolutions per minute
    3. The road speed of the motorcycle Correct answer.
    4. The gear the transmission is in

    Explanation

    The speedometer shows road speed, usually in kilometres per hour. Engine speed is shown by the tachometer and distance by the odometer.

  132. Question 132Motorcycle controls, handling and vehicle familiarity

    What should a rider do with the side stand before riding away?

    1. Remove it if the motorcycle has a centre stand
    2. Rest it lightly on the road surface
    3. Fold it fully up into its retracted position Correct answer.
    4. Leave it down as a warning to others

    Explanation

    A side stand left down can catch the road on a left turn and cause a loss of control. It must be fully retracted before moving off, and the safety switch helps ensure this.

  133. Question 133Motorcycle controls, handling and vehicle familiarity

    What is the purpose of the motorcycle's horn?

    1. To request priority at an intersection
    2. To warn other road users of your presence Correct answer.
    3. To indicate that you are slowing down
    4. To signal that you are turning left

    Explanation

    The horn is a warning device to alert others who may not have seen you. It is not a substitute for turn signals, brake lights, or right-of-way rules.

  134. Question 134Motorcycle controls, handling and vehicle familiarity

    A rider is preparing to move off from a stop on a slight uphill grade. What technique best prevents rolling backward?

    1. Hold the rear brake while easing out the clutch into the friction zone Correct answer.
    2. Pull the front brake hard and release the clutch quickly
    3. Release both brakes and rely on the engine's idle
    4. Keep the clutch fully pulled in until the motorcycle is rolling

    Explanation

    Holding the rear brake keeps the motorcycle from rolling back while the clutch enters the friction zone and the throttle is applied. Once drive engages, the brake is released smoothly.

  135. Question 135Motorcycle controls, handling and vehicle familiarity

    Why should a rider keep the throttle steady while leaning the motorcycle into a turn?

    1. Steady throttle reduces the need for countersteering
    2. Steady throttle automatically lowers the selected gear
    3. Steady throttle keeps the suspension settled and the tires gripping Correct answer.
    4. Steady throttle makes the front brake more effective mid-turn

    Explanation

    A constant throttle through the turn maintains weight balance and tire grip. Abrupt changes in throttle can upset the chassis and cause the tires to lose traction.

  136. Question 136Motorcycle controls, handling and vehicle familiarity

    What is the correct sequence for slowing to a stop on a manual motorcycle from normal road speed?

    1. Pull the clutch first, then apply only the rear brake
    2. Apply the front brake hard, then pull the clutch at the last moment
    3. Downshift through all gears first, then brake
    4. Roll off the throttle, apply both brakes smoothly, and downshift as speed drops Correct answer.

    Explanation

    Rolling off the throttle begins deceleration, and both brakes are applied progressively for maximum control. Shifting down as speed falls keeps the motorcycle in the right gear for the stop.

  137. Question 137Motorcycle controls, handling and vehicle familiarity

    A rider must make an emergency stop on a dry, straight road. Which action gives the shortest stopping distance?

    1. Apply only the rear brake to avoid a front-wheel skid
    2. Release the throttle and coast without braking
    3. Apply the front brake fully and instantly in one motion
    4. Apply both brakes firmly and progressively while keeping the motorcycle upright Correct answer.

    Explanation

    On a dry straight road, both brakes used firmly and progressively give the shortest stop. The front brake provides most of the stopping power, and smooth application avoids locking a wheel.

  138. Question 138Motorcycle controls, handling and vehicle familiarity

    What does the friction zone of the clutch refer to?

    1. The range where the clutch is partially engaged and begins to transmit drive Correct answer.
    2. The point where the clutch is fully released
    3. The interval between gear changes
    4. The point where the clutch is fully pulled in

    Explanation

    The friction zone is the part of the lever travel where the clutch plates start to grip and power begins to reach the rear wheel. Riders use it for smooth starts and low-speed control.

  139. Question 139Motorcycle controls, handling and vehicle familiarity

    A rider notices the steering feels heavy and the motorcycle wanders at low speed. Which cause should be checked first?

    1. A loose exhaust bracket
    2. A worn clutch cable
    3. Under-inflated tires Correct answer.
    4. A dirty air filter

    Explanation

    Low tire pressure makes steering heavy and causes the motorcycle to wander, especially at low speed. Tire pressure should be checked first as it directly affects handling and safety.

  140. Question 140Motorcycle controls, handling and vehicle familiarity

    When riding over a pothole or raised obstacle, what is the best technique?

    1. Rise slightly off the seat and keep a firm grip on the bars Correct answer.
    2. Sit heavily on the seat to absorb the impact
    3. Turn sharply to avoid it at the last second
    4. Apply the front brake as the front wheel reaches the obstacle

    Explanation

    Rising slightly off the seat lets the legs absorb the impact and keeps the rider balanced and in control. A firm grip on the bars keeps the front wheel steady.

  141. Question 141Motorcycle controls, handling and vehicle familiarity

    Why should a rider avoid covering the front brake lever with the fingers during normal cruising?

    1. It disables the rear brake
    2. It causes the clutch to slip
    3. An unexpected grab of the lever can cause a front-wheel skid or a sudden stop Correct answer.
    4. It prevents the throttle from being used

    Explanation

    Resting fingers on the front brake lever can lead to an unintended grab when the rider is surprised, which may lock the front wheel. Riders should cover the brake only when a hazard is expected.

  142. Question 142Motorcycle controls, handling and vehicle familiarity

    What does engine braking do when the rider rolls off the throttle while in gear?

    1. It disengages the clutch automatically
    2. It accelerates the motorcycle without throttle input
    3. It slows the motorcycle through the engine's compression Correct answer.
    4. It applies the rear brake pedal electronically

    Explanation

    With the throttle closed and the clutch engaged, the engine resists turning and slows the motorcycle. This is useful on descents and when approaching a stop.

  143. Question 143Motorcycle controls, handling and vehicle familiarity

    A rider is turning into a driveway at very low speed. Which technique gives the most control?

    1. Shift into a higher gear before the turn
    2. Apply the front brake gently through the turn
    3. Use the friction zone with light throttle and slip the clutch as needed Correct answer.
    4. Pull the clutch fully in and coast through the turn

    Explanation

    At low speed the motorcycle needs some drive to stay stable. The friction zone with a little throttle lets the rider control speed smoothly without stalling or coasting.

  144. Question 144Motorcycle controls, handling and vehicle familiarity

    What is the correct way to adjust the rearview mirrors before a ride?

    1. Adjust them while standing beside the motorcycle
    2. Adjust them only when the motorcycle is loaded with a passenger
    3. Adjust them after the motorcycle is moving
    4. Adjust them while seated in the normal riding position Correct answer.

    Explanation

    Mirrors should be set while seated in the normal riding position so the view matches what the rider will see on the road. Adjusting them at any other time gives a misleading view.

  145. Question 145Motorcycle controls, handling and vehicle familiarity

    A rider hears a continuous squeal from the front wheel when the brake is applied lightly. What is the most likely cause?

    1. A loose steering head bearing
    2. A stretched clutch cable
    3. Worn brake pads or a glazed rotor Correct answer.
    4. Low engine oil level

    Explanation

    Squealing during braking often points to worn pads or a glazed rotor that needs inspection. Brakes should be checked promptly because stopping power may be reduced.

  146. Question 146Motorcycle controls, handling and vehicle familiarity

    What is the effect of over-tightening the drive chain on a motorcycle?

    1. It can damage the bearings and suspension and cause premature wear Correct answer.
    2. It reduces tire pressure
    3. It improves acceleration and handling
    4. It increases the clutch friction zone

    Explanation

    An over-tightened chain puts excessive load on the gearbox output bearing, the rear wheel bearings, and the suspension. The chain should be set to the manufacturer's specified slack.

  147. Question 147Motorcycle controls, handling and vehicle familiarity

    A rider is carrying a heavy load in a tail bag. How does this affect the motorcycle's handling?

    1. The front end feels lighter and steering response changes Correct answer.
    2. The rear brake pedal travel increases
    3. The front brake becomes ineffective
    4. The clutch friction zone widens

    Explanation

    Adding weight behind the rear axle lightens the front wheel, which can make steering feel vague and reduce front grip. Tire pressures and suspension settings may need adjustment for the load.

  148. Question 148Motorcycle controls, handling and vehicle familiarity

    Why is it important to match engine speed when downshifting before a turn?

    1. To reduce the need to use the turn signals
    2. To prevent rear-wheel hop or loss of traction as the clutch re-engages Correct answer.
    3. To increase the brightness of the headlight
    4. To shorten the life of the clutch plates

    Explanation

    If engine speed is too low for the selected gear, the rear wheel can lock or hop when the clutch engages. Matching speed with a brief throttle blip keeps the rear tire gripping smoothly.

  149. Question 149Motorcycle controls, handling and vehicle familiarity

    A rider is riding in strong crosswinds on an open highway. Which technique best maintains control?

    1. Speed up to push through the wind
    2. Reduce speed and keep a firm, relaxed grip while allowing for wind drift Correct answer.
    3. Lean sharply into the wind and hold that lean
    4. Release the handlebars briefly to let the motorcycle correct itself

    Explanation

    In crosswinds, reducing speed and holding a firm but relaxed grip lets the rider make smooth corrections. Anticipating wind drift and giving space to the side is essential.

  150. Question 150Motorcycle controls, handling and vehicle familiarity

    A rider on a wet road needs to brake. What adjustment to technique is most appropriate?

    1. Grab the front brake firmly to test the grip
    2. Use the rear brake only and apply it late
    3. Apply the front brake only and squeeze harder
    4. Apply both brakes more gently and earlier than on dry pavement Correct answer.

    Explanation

    Wet pavement reduces available grip, so braking should be smoother and started earlier. Both brakes are used gently with progressive pressure to avoid locking a wheel.

  151. Question 151Signs, signals, road markings and right-of-way

    A solid yellow line on your side of the road means:

    1. The lane is reserved for turning traffic
    2. Passing is permitted when the road ahead is clear
    3. The speed limit drops by 20 km/h
    4. No passing on your side of the line Correct answer.

    Explanation

    A solid yellow line on your side of the centre line marks a no-passing zone for traffic moving in your direction. You may not cross it to overtake. A broken yellow line on your side would permit passing when safe.

  152. Question 152Signs, signals, road markings and right-of-way

    At an intersection with no signs or signals, a driver must yield the right-of-way to:

    1. The vehicle approaching from the left
    2. The vehicle that arrives last
    3. The vehicle with the larger engine
    4. The vehicle already in the intersection Correct answer.

    Explanation

    At an uncontrolled intersection, the driver already in the intersection has the right-of-way, and approaching drivers must yield. If two vehicles arrive at about the same time, the one on the right goes first.

  153. Question 153Signs, signals, road markings and right-of-way

    A flashing red traffic light at an intersection requires you to:

    1. Treat it as a green light for turning only
    2. Slow down and proceed without stopping
    3. Stop only if another vehicle is present
    4. Stop completely, then proceed when safe Correct answer.

    Explanation

    A flashing red light functions like a stop sign: come to a full stop, yield to traffic and pedestrians, and proceed only when it is safe. A flashing amber light, by contrast, means slow down and proceed with caution.

  154. Question 154Signs, signals, road markings and right-of-way

    A school zone sign with a flashing amber light indicates that you must:

    1. Change lanes to the left
    2. Reduce speed to the posted school zone limit Correct answer.
    3. Sound your horn before proceeding
    4. Stop and wait for a crossing guard

    Explanation

    When the school zone light is flashing, the reduced speed limit shown on the school zone sign is in effect. You must slow to that limit and watch for children. The limit applies only during the times indicated.

  155. Question 155Signs, signals, road markings and right-of-way

    A stop sign requires you to stop:

    1. Only if the light ahead is red
    2. Only when other traffic is approaching
    3. Several metres before the sign so you can see over it
    4. At the stop line, or at the edge of the intersection if there is no line Correct answer.

    Explanation

    You must stop at the marked stop line. Where no line exists, stop at the nearest crosswalk, or at the edge of the roadway before entering the intersection. Stopping short of the line can block visibility and is not a legal stop.

  156. Question 156Signs, signals, road markings and right-of-way

    A yellow diamond-shaped sign is used to:

    1. Mark hospital and emergency facilities
    2. Give regulatory orders such as speed limits
    3. Identify construction zones only
    4. Warn of hazards or changing road conditions Correct answer.

    Explanation

    Yellow diamond signs are warning signs that alert drivers to hazards ahead, such as curves, intersections, or slippery pavement. Regulatory signs are typically white rectangles with black or red markings.

  157. Question 157Signs, signals, road markings and right-of-way

    A broken white line between two lanes travelling in the same direction means:

    1. Lane changing is prohibited
    2. Traffic must merge immediately
    3. Lane changing is permitted when safe Correct answer.
    4. The left lane is for buses only

    Explanation

    Broken white lines separate lanes of traffic moving in the same direction and may be crossed when it is safe to change lanes. A solid white line discourages or prohibits lane changes depending on the marking.

  158. Question 158Signs, signals, road markings and right-of-way

    When a pedestrian is crossing at a marked crosswalk with no traffic signal, you must:

    1. Yield only if the pedestrian has already stepped onto your half of the road
    2. Proceed if you can pass behind the pedestrian
    3. Yield and let the pedestrian finish crossing Correct answer.
    4. Sound your horn to warn the pedestrian

    Explanation

    Drivers must yield to pedestrians in a crosswalk, whether marked or unmarked, and must not proceed until the pedestrian has safely cleared the vehicle's path. Pedestrians in a crosswalk have the right-of-way.

  159. Question 159Signs, signals, road markings and right-of-way

    An orange diamond-shaped sign in a work zone indicates:

    1. A permanent hazard that applies year-round
    2. Construction or maintenance activity ahead Correct answer.
    3. A railway crossing
    4. A school crossing

    Explanation

    Orange signs mark construction and maintenance zones and warn of temporary conditions such as workers, equipment, or lane closures. Reduced speeds posted in these zones are legally enforceable.

  160. Question 160Signs, signals, road markings and right-of-way

    You are approaching a railway crossing with flashing red lights and no gate. You should:

    1. Stop, then proceed if no train is visible
    2. Slow down and cross if the lights just started flashing
    3. Stop and remain stopped until the lights stop flashing and the way is clear Correct answer.
    4. Drive around the lights if the crossing arm is up

    Explanation

    Flashing red lights at a railway crossing mean a train is approaching, and you must stop and remain stopped until the signals stop and you are certain no train is coming. Never proceed just because a train is not yet visible.

  161. Question 161Signs, signals, road markings and right-of-way

    A driver entering a highway from a private driveway must:

    1. Proceed because entering vehicles have priority
    2. Stop only if a sign requires it
    3. Yield to traffic already on the highway Correct answer.
    4. Expect highway traffic to change lanes

    Explanation

    A driver entering a roadway from a driveway, alley, or private road must yield the right-of-way to all traffic already on the roadway. The entering driver must wait for a safe gap.

  162. Question 162Signs, signals, road markings and right-of-way

    A double solid yellow line means:

    1. Passing is permitted for both directions
    2. The road becomes one-way ahead
    3. Only trucks may cross the line
    4. Passing is prohibited for traffic in both directions Correct answer.

    Explanation

    A double solid yellow line prohibits passing for traffic moving in both directions. You may cross it only to turn into or out of a driveway or side road where permitted.

  163. Question 163Signs, signals, road markings and right-of-way

    At a four-way stop, two vehicles arrive at the same time from opposite directions, and one is turning left. Who goes first?

    1. The vehicle turning left
    2. The vehicle going straight Correct answer.
    3. Whichever vehicle honks first
    4. The larger vehicle

    Explanation

    When two vehicles arrive simultaneously at a four-way stop from opposite directions and one is turning left, the left-turning vehicle must yield to the vehicle going straight. The straight-through vehicle proceeds first.

  164. Question 164Signs, signals, road markings and right-of-way

    A sign showing a black arrow curving to the right inside a yellow diamond warns that:

    1. The right lane ends ahead
    2. Right turns are prohibited
    3. The road curves to the right ahead Correct answer.
    4. A right-turn lane begins

    Explanation

    A yellow diamond with a curved arrow warns of a curve ahead in the direction shown. Drivers should reduce speed before entering the curve.

  165. Question 165Signs, signals, road markings and right-of-way

    A green arrow traffic signal means:

    1. You have a protected turn in the direction of the arrow Correct answer.
    2. You must stop before turning
    3. The arrow applies only to buses
    4. You may turn in the direction of the arrow after yielding to oncoming traffic

    Explanation

    A green arrow gives a protected right-of-way to turn in the direction shown; conflicting traffic is stopped. A solid green light, by contrast, requires you to yield to oncoming traffic before turning left.

  166. Question 166Signs, signals, road markings and right-of-way

    You are in a lane marked with a white left-turn arrow on the pavement. This means:

    1. You may go straight or turn left
    2. You must merge right immediately
    3. The lane is for passing only
    4. You must turn left from this lane Correct answer.

    Explanation

    A pavement arrow pointing left designates a mandatory left-turn lane. You must turn left from that lane and may not proceed straight.

  167. Question 167Signs, signals, road markings and right-of-way

    When an emergency vehicle approaches with its siren and lights on, you should:

    1. Speed up to clear the intersection
    2. Pull to the right and stop until it passes Correct answer.
    3. Follow closely behind it
    4. Stop immediately wherever you are

    Explanation

    When an emergency vehicle approaches with lights and siren, move to the right side of the road and stop until it has passed. Do not stop in an intersection; clear it first.

  168. Question 168Signs, signals, road markings and right-of-way

    A white rectangular sign with black lettering reading 'MAXIMUM 50' is:

    1. A guide sign
    2. A warning sign
    3. A construction sign
    4. A regulatory speed limit sign Correct answer.

    Explanation

    White rectangular signs with black lettering are regulatory signs that state laws or rules, including speed limits. Warning signs are yellow diamonds, and construction signs are orange.

  169. Question 169Signs, signals, road markings and right-of-way

    On a two-lane road, a solid yellow line appears on your side and a broken yellow line on the other side. This means:

    1. Both directions may pass
    2. You may pass but oncoming traffic may not
    3. Neither direction may pass
    4. Oncoming traffic may pass but you may not Correct answer.

    Explanation

    Each side of the centre line applies to the traffic beside it. A broken line on the oncoming side permits those drivers to pass, while the solid line on your side prohibits you from passing.

  170. Question 170Signs, signals, road markings and right-of-way

    A yield sign requires you to:

    1. Accelerate to merge ahead of traffic
    2. Come to a complete stop every time
    3. Slow down and give the right-of-way to traffic on the through road Correct answer.
    4. Stop only if a pedestrian is present

    Explanation

    A yield sign means slow down and give the right-of-way to traffic on the intersecting road, stopping only if necessary. You may proceed without stopping when there is a safe gap.

  171. Question 171Signs, signals, road markings and right-of-way

    A sign with a red circle and a diagonal slash over a symbol means:

    1. The action shown applies only at night
    2. The action shown is required
    3. The action shown is prohibited Correct answer.
    4. The action shown is recommended

    Explanation

    A red circle with a diagonal slash is the universal prohibition symbol, meaning the action depicted is not allowed. These are regulatory signs and carry the force of law.

  172. Question 172Signs, signals, road markings and right-of-way

    You approach an intersection where the traffic signal is dark because of a power failure. You should:

    1. Wait until the signal is repaired
    2. Treat the intersection as uncontrolled and yield as at a four-way stop Correct answer.
    3. Turn right and find another route
    4. Proceed without slowing because the light is off

    Explanation

    When a signal is dark, treat the intersection as an all-way stop: stop, then proceed in order of arrival, yielding to the vehicle on the right when arrival is simultaneous.

  173. Question 173Signs, signals, road markings and right-of-way

    Two vehicles reach an uncontrolled intersection at nearly the same moment, one from the north and one from the east. Which vehicle has the right-of-way?

    1. Neither; both must reverse
    2. The vehicle from the north
    3. The vehicle travelling faster
    4. The vehicle from the east Correct answer.

    Explanation

    At an uncontrolled intersection, when vehicles arrive at about the same time, the vehicle on the right has the right-of-way. The vehicle from the east is on the right of the vehicle from the north, so it goes first.

  174. Question 174Signs, signals, road markings and right-of-way

    A driver wishes to turn left at an intersection with a solid green light and no arrow. The driver must:

    1. Yield to oncoming traffic and pedestrians before turning Correct answer.
    2. Wait for a green arrow before turning at all
    3. Turn from any lane in the intersection
    4. Turn immediately because the light is green

    Explanation

    A solid green light permits a left turn only after yielding to oncoming traffic and pedestrians in the crosswalk. The turn must be made from the designated lane.

  175. Question 175Signs, signals, road markings and right-of-way

    A bus is stopped with its hazard lights on in a marked school bus loading zone, and children are crossing the road. You should:

    1. Proceed because the bus is not showing a stop arm
    2. Pass the bus slowly on the left
    3. Sound your horn to alert the children
    4. Stop and remain stopped until the children have cleared the roadway Correct answer.

    Explanation

    When children are crossing near a stopped school bus, you must stop and wait until they have safely cleared the roadway, regardless of whether the stop arm is extended. Children may move unpredictably.

  176. Question 176Signs, signals, road markings and right-of-way

    A red octagonal sign always requires a rider to:

    1. Yield only to vehicles coming from the right
    2. Slow down and proceed if the road looks clear
    3. Stop only when a pedestrian is present
    4. Come to a complete stop before the stop line or crosswalk Correct answer.

    Explanation

    The octagonal shape is reserved exclusively for stop signs, so the shape alone identifies the required action. A full stop must be made at the stop line, crosswalk or edge of the roadway before proceeding.

  177. Question 177Signs, signals, road markings and right-of-way

    A pennant-shaped yellow sign with black lettering is placed on the left side of a two-way road to indicate:

    1. The end of a divided highway
    2. The start of a passing zone
    3. A school zone ahead
    4. A no-passing zone on your side Correct answer.

    Explanation

    The pennant shape is used only for no-passing zone signs, and it is mounted on the left side of the roadway facing traffic in the restricted direction. It marks where passing becomes prohibited.

  178. Question 178Signs, signals, road markings and right-of-way

    You are riding and see a yellow diamond sign showing a traffic signal. This warns that:

    1. Signals at the next intersection are not working
    2. You must stop immediately before the sign
    3. A railway crossing with signals is ahead
    4. A traffic signal is ahead and may be red when you reach it Correct answer.

    Explanation

    The signal-ahead warning sign tells riders that a signalized intersection is coming, often where sight distance is limited. You should be prepared to stop if the light is red or changes.

  179. Question 179Signs, signals, road markings and right-of-way

    A white square sign with a black symbol of a bicycle indicates:

    1. Cyclists are prohibited beyond this point
    2. A bicycle repair facility
    3. A lane or route designated for cyclists Correct answer.
    4. A bicycle race is in progress

    Explanation

    White regulatory signs with black symbols give orders or permissions. A bicycle symbol designates a bikeway, bike lane or shared route where cyclists are expected.

  180. Question 180Signs, signals, road markings and right-of-way

    On a roadway, a single broken yellow line means:

    1. Passing is prohibited in both directions
    2. Traffic must keep to the right of the line at all times
    3. Traffic may pass when it is safe to do so Correct answer.
    4. The lane is reserved for turning vehicles

    Explanation

    A broken yellow line separates traffic moving in opposite directions and permits passing when visibility and clear distance allow. The rider must still judge whether the manoeuvre can be completed safely.

  181. Question 181Signs, signals, road markings and right-of-way

    A solid white line marks the edge of the roadway on the right side. A rider may cross it:

    1. Never, under any circumstances
    2. Only during daylight hours
    3. Only when passing another vehicle
    4. Only to enter a driveway or shoulder when it is safe Correct answer.

    Explanation

    An edge line marks the boundary of the travelled roadway, but a rider may cross it when necessary to enter a driveway, pull onto the shoulder or leave the road safely. Passing another vehicle is not a valid reason to cross the edge line.

  182. Question 182Signs, signals, road markings and right-of-way

    A flashing yellow traffic light at an intersection means:

    1. Yield only to vehicles turning right
    2. Stop and wait for a green light
    3. The signal is broken and the intersection must be avoided
    4. Proceed with caution after yielding to cross traffic and pedestrians Correct answer.

    Explanation

    A flashing yellow light cautions riders to slow down and proceed carefully, giving way to traffic already in the intersection and to pedestrians. It does not require a stop.

  183. Question 183Signs, signals, road markings and right-of-way

    A flashing red traffic light must be treated in the same way as:

    1. A yield sign
    2. A warning sign
    3. A green light
    4. A stop sign Correct answer.

    Explanation

    A flashing red light requires a complete stop, after which you may proceed when it is safe, exactly as at a stop sign. Failing to stop fully is a violation.

  184. Question 184Signs, signals, road markings and right-of-way

    A green light is showing but the intersection ahead is blocked by queued traffic. You should:

    1. Sound your horn until traffic moves
    2. Drive around the queue using the oncoming lane
    3. Enter the intersection and wait in the middle
    4. Wait behind the stop line until there is room to clear the intersection Correct answer.

    Explanation

    Even with a green light, a rider must not enter an intersection unless there is space to clear it. Blocking the intersection obstructs cross traffic and pedestrians when their signal changes.

  185. Question 185Signs, signals, road markings and right-of-way

    A sign with a yellow diamond showing a black symbol of a slippery road surface warns of:

    1. A paved surface that may be slippery when wet Correct answer.
    2. An uneven road surface ahead
    3. A steep downhill grade
    4. Loose gravel on the shoulder

    Explanation

    The slippery-when-wet warning alerts riders that traction may be reduced on the paved surface during rain or frost. Riders should reduce speed and avoid sudden braking or steering inputs.

  186. Question 186Signs, signals, road markings and right-of-way

    You are riding behind a cyclist on a road with a marked bicycle lane on the right. When you intend to turn right:

    1. Pass the cyclist first and then brake sharply in front of them
    2. Signal, check the mirror and shoulder, and yield to the cyclist before turning Correct answer.
    3. Expect the cyclist to stop and wait for your turn
    4. Move into the bike lane early and wait there

    Explanation

    A cyclist travelling straight has the right-of-way over a vehicle turning right across their path. Signal early, check mirrors and blind spots, and turn only when the cyclist's path is clear.

  187. Question 187Signs, signals, road markings and right-of-way

    A yellow diamond sign showing a black arrow bending sharply to the left, with a smaller advisory speed plate beneath it, tells you:

    1. The left turn is prohibited
    2. The road narrows to the left
    3. A left lane ends ahead
    4. The curve should be taken no faster than the posted advisory speed Correct answer.

    Explanation

    Advisory speed plates on curve warning signs recommend a safe maximum speed for the bend under good conditions. Riding faster risks running wide or losing traction, especially on a motorcycle.

  188. Question 188Signs, signals, road markings and right-of-way

    A black-on-white sign reading 'KEEP RIGHT OF MEDIAN' means:

    1. Right turns are not permitted
    2. Traffic must turn right at the next intersection
    3. The right lane is closed ahead
    4. Traffic must pass to the right side of the raised divider Correct answer.

    Explanation

    This regulatory sign directs traffic to keep to the right of a median or traffic island. Passing on the left side would put you into opposing traffic.

  189. Question 189Signs, signals, road markings and right-of-way

    A rider approaches a crosswalk where a school crossing guard has stepped onto the road holding a stop sign. The rider must:

    1. Continue if no children are visible
    2. Stop and remain stopped until the guard clears the roadway Correct answer.
    3. Stop only if the guard signals directly at them
    4. Slow down and pass behind the guard

    Explanation

    A crossing guard displaying a stop sign has the authority to halt traffic, and riders must stop and stay stopped until the guard and pedestrians have cleared. Proceeding early endangers children who may still be crossing.

  190. Question 190Signs, signals, road markings and right-of-way

    A sign showing a black pedestrian symbol inside a yellow diamond warns that:

    1. The sidewalk is closed
    2. Pedestrians are prohibited in the area
    3. A pedestrian crosswalk is ahead Correct answer.
    4. A school bus stop is ahead

    Explanation

    The pedestrian warning sign alerts riders that a crosswalk or heavy pedestrian activity lies ahead. Riders should slow down and be ready to stop for people crossing.

  191. Question 191Signs, signals, road markings and right-of-way

    You are riding on a road with two lanes in your direction and a broken white line between them. Compared with the lane on your right, the left lane is:

    1. Reserved for buses only
    2. For oncoming traffic
    3. For passing or preparing for a left turn Correct answer.
    4. Closed to motorcycles

    Explanation

    A broken white line separates lanes travelling in the same direction and permits lane changes when safe. The left lane may be used for passing or to position for a left turn.

  192. Question 192Signs, signals, road markings and right-of-way

    A rider is entering a roundabout. Right-of-way belongs to:

    1. Vehicles entering from the left
    2. The largest vehicle approaching
    3. Whichever vehicle arrives first
    4. Traffic already circulating in the roundabout Correct answer.

    Explanation

    Traffic already inside the roundabout has the right-of-way, and entering riders must yield. Riders should also watch for pedestrians at the crosswalks on each approach.

  193. Question 193Signs, signals, road markings and right-of-way

    A traffic light shows a solid red light with a green arrow pointing left. A rider wanting to turn left may:

    1. Turn left only if a sign permits it
    2. Turn left without stopping, because the arrow protects the movement Correct answer.
    3. Turn left after yielding to oncoming traffic
    4. Not turn until the light turns solid green

    Explanation

    A green arrow gives a protected movement, meaning opposing traffic is stopped and the turn may be made without yielding. The arrow applies only to the direction it indicates.

  194. Question 194Signs, signals, road markings and right-of-way

    A sign with a red circle and a black 'P' crossed by a diagonal slash means:

    1. A parking lot entrance is ahead
    2. Parking for permit holders only
    3. No parking at any time Correct answer.
    4. Parking is permitted for a limited time

    Explanation

    A red circle with a diagonal slash is the universal prohibition symbol, so the crossed-out P prohibits parking. Time-limited or permit parking would be shown with additional plates rather than a slash.

  195. Question 195Signs, signals, road markings and right-of-way

    A rider is stopped at a red light and wants to turn right onto a one-way street. After stopping fully, the rider may turn right:

    1. Only if another vehicle turns first
    2. Only after the light turns green
    3. Only if a sign does not prohibit it and the way is clear Correct answer.
    4. Never, because right turns on red are always illegal

    Explanation

    In Alberta, a right turn on a red light is permitted after a complete stop unless a sign prohibits it, and the rider must yield to pedestrians and cross traffic. Turning into a one-way street is also allowed where turns on red are permitted.

  196. Question 196Signs, signals, road markings and right-of-way

    A yellow diamond sign showing two arrows, one pointing up and one merging from the right, warns that:

    1. Traffic will enter from the right and must be accommodated Correct answer.
    2. A divided highway begins
    3. The right lane will end and merge into your lane
    4. A right turn is mandatory ahead

    Explanation

    The merge warning sign alerts riders that traffic from another lane or ramp will join the roadway. Riders should adjust speed and lane position to allow a safe merge.

  197. Question 197Signs, signals, road markings and right-of-way

    A rider is following a large truck that has stopped before a crosswalk and is signalling to turn left. The rider should:

    1. Pass the truck on the left immediately
    2. Wait behind the truck, as it may be blocking a pedestrian the rider cannot see Correct answer.
    3. Assume the truck is broken down and go around
    4. Pass the truck on the right along the shoulder

    Explanation

    A stopped large vehicle can hide a pedestrian crossing in front of it. Passing on either side risks striking someone the rider cannot see until it is too late.

  198. Question 198Signs, signals, road markings and right-of-way

    A rider approaches a railway crossing with a stop sign mounted at the crossing and no gate or lights. The rider must:

    1. Stop, look and listen in both directions before crossing Correct answer.
    2. Slow down and cross if no train is visible
    3. Stop only if a train is within sight
    4. Sound the horn and proceed without stopping

    Explanation

    Where a stop sign is posted at a railway crossing, a complete stop is mandatory before crossing. The rider must then check both directions and listen for an approaching train.

  199. Question 199Signs, signals, road markings and right-of-way

    A rider is in a lane marked with a white diamond symbol and the word 'HOV' on the pavement. This lane is reserved for:

    1. Commercial trucks only
    2. Motorcycles and high-occupancy vehicles as posted Correct answer.
    3. Vehicles turning left at the next intersection
    4. All single-occupant vehicles during rush hour

    Explanation

    High-occupancy vehicle lanes are reserved for vehicles carrying the posted minimum number of occupants, and motorcycles are commonly permitted regardless of occupancy. Signs at the lane entrance state the exact rules.

  200. Question 200Signs, signals, road markings and right-of-way

    A rider sees a yellow diamond sign depicting a traffic light with a red light shown. The sign is placed well before the intersection. The rider should:

    1. Reduce speed and prepare to stop if the light is red Correct answer.
    2. Stop at the sign and wait for a green light
    3. Maintain speed because the light will likely be green
    4. Change lanes immediately to the right

    Explanation

    The signal-ahead warning is placed where the signal may not be visible in time to stop safely at normal speed. Adjusting speed early gives the rider room to stop smoothly if the light is red.

Alberta Class 6 Motorcycle Test flashcards

32 cards. Read the term and the definition here. The deck at the top of this page is optional.

Class 6 licence
The Alberta licence class required to operate a motorcycle on public roads. Riders progress through a learner stage with restrictions before receiving a full Class 6 licence.
Helmet requirement
In Alberta, every motorcycle rider and passenger must wear a properly fastened helmet meeting the standards in the vehicle equipment regulation. It is mandatory regardless of rider experience.
Lane splitting
Riding a motorcycle between lanes of moving traffic or sharing a lane beside another vehicle. This is not permitted in Alberta; a motorcycle is entitled to a full lane.
Passenger rules
A motorcycle may carry one passenger only when the bike is designed for two riders and has a proper passenger seat and footrests. The passenger must also wear an approved helmet.
Graduated licensing alcohol
Alberta's Graduated Driver Licensing program imposes a zero-alcohol condition on novice riders. Any alcohol in the blood is a contravention for a GDL motorcycle rider.
Following too closely
A contravention where a driver fails to leave enough distance to stop safely if the vehicle ahead slows suddenly. Motorcycles need at least the same gap as cars.
Signal cancellation
After turning or changing lanes, the rider must cancel the turn signal. A signal left flashing misleads other drivers about the rider's next move and creates a hazard.
Two-second rule
A minimum following gap measured as the time between your motorcycle passing a fixed object and the vehicle ahead passing it. Double it in poor conditions.
Target fixation
The tendency to steer toward whatever the rider stares at. Because the bike follows the gaze, riders must look at the intended path, not the hazard.
Lane position choice
Riders choose a lane position based on visibility, escape routes, and surface quality. Avoid the oily centre strip at intersections and stay out of blind spots.
Railway track crossing
Cross tracks as close to a right angle as possible to prevent the front tire from being deflected. Wet steel rails offer very little grip to a leaning motorcycle.
First rain hazard
The first rain after a dry spell lifts accumulated oil and rubber dust from the pavement, making the surface especially slippery. Reduce speed and lean angle.
Cold tire grip
Tires grip less when cold, and cold pavement reduces traction further. The first minutes of a ride require gentler braking, acceleration and cornering.
Staggered group formation
A riding formation where riders alternate left and right positions on straight roads, keeping a two-second gap to the rider directly ahead. Curves are ridden single file.
Total stopping distance
The sum of perception distance, reaction distance and braking distance. It grows quickly with speed, and wet or gravel surfaces lengthen the braking portion.
Countersteering
At speeds above walking pace, pushing the right handlebar forward leans the bike right and turns it right; pushing the left grip forward leans and turns it left.
Front brake power
The front brake supplies most of a motorcycle's stopping force because weight transfers forward under braking. Apply it progressively rather than grabbing it suddenly.
Friction zone
The portion of clutch lever travel where engine power begins to reach the rear wheel. Riders use it for smooth starts, slow-speed control and hill starts.
Right-hand controls
The right hand operates the throttle and front brake lever. The right foot operates the rear brake pedal. These two controls work together for stopping.
Left-hand controls
The left hand operates the clutch lever and the turn signal switch. The left foot operates the gear shift lever, usually a one-down, rest-up pattern.
Slow-speed stability
At walking pace, stability comes from the clutch friction zone and light rear brake drag, keeping the throttle steady. Do not use front brake alone while turning slowly.
Pre-ride check
A quick inspection before riding: tire pressure and tread, controls, lights, horn, oil and fuel, and chain or belt tension. It catches faults before they become failures.
Engine braking
Rolling off the throttle slows the rear wheel through engine compression. Downshift one gear at a time and match engine speed to road speed to prevent rear-wheel lockup.
Rider posture
Grip the tank with the knees, keep arms bent and relaxed, and look well ahead. A tight grip on the handlebars transmits unintended input and unsettles the motorcycle.
Yield sign
A red-and-white triangle meaning the rider must slow and give way to traffic that has the right of way. Stop if necessary before entering the intersecting road.
Solid yellow centre line
A solid yellow line marks the centre of a two-way road and prohibits passing in both directions. A broken yellow line on your side allows passing when safe.
Flashing red signal
A flashing red traffic light is treated exactly like a stop sign: come to a complete stop, yield to traffic with the right of way, then proceed when clear.
Uncontrolled intersection
An intersection with no signs or signals. The first vehicle to arrive has the right of way; if two arrive together, the vehicle on the right proceeds first.
Left turn right-of-way
A vehicle turning left must yield to oncoming traffic going straight or turning right, and to pedestrians in the crosswalk. Wait for a safe gap before turning.
Stop line placement
At a stop sign or signal, stop at the painted stop line or crosswalk line. If no line exists, stop before the crosswalk or the edge of the intersecting road.
Orange construction signs
Orange signs mark construction and maintenance zones. Posted reduced speed limits in these zones are enforceable and riders should expect loose gravel and changed lane paths.
School bus red lights
When a school bus displays flashing red lights, traffic in both directions must stop unless separated by a median. Passing a stopped school bus with red lights is prohibited.

Alberta Class 6 Motorcycle Test study guide

Alberta Traffic Law and Rules of the Road for Motorcyclists

A motorcycle is a motor vehicle under Alberta law, so every rule that applies to cars applies to you - plus a few that exist only because you have two wheels. Know the core set: ride on the right-hand side of the roadway, keep both wheels on the pavement, and never share a lane with another vehicle. Lane splitting and lane filtering are not permitted in Alberta; a motorcycle is entitled to a full lane, and other drivers must not crowd you in it.

Riding position and passengers

Ride as far to the right of your lane as is safe for the conditions, but move to the centre or left when you need to be seen, avoid debris, or prepare to turn left. A passenger is legal only if the bike has a proper seat and footrests for them, and a rider carrying a passenger must hold a full (non-learner) Class 6 licence. Helmets are mandatory for every rider and passenger.

Signals, lights and turns

Signal every lane change and turn, and cancel it afterward - a stuck signal is a classic exam trap. Left turns at intersections are made from the left portion of your lane, not from beside a car. At a stop sign or red light, come to a complete stop; a foot-down stop is the clearest evidence you did.

Traps to watch for

Questions love edge cases: whether you may ride two abreast (no - one rider per lane position, staggered only in a group), whether a learner may carry a passenger (no), and whether you can pass on the shoulder (no). Read for the words "always" and "never" - most such absolutes are false except for helmets and sobriety.

Rule of thumb: if a manoeuvre would put two vehicles in one lane, or put you off the paved surface, it is illegal in Alberta unless a sign explicitly permits it.

Safe Riding Practices and Hazard Awareness

Most motorcycle crashes are not caused by a lack of skill at the controls - they are caused by a rider who did not see, or was not seen, in time. Build your riding around three habits: see far ahead, be visible, and always have an escape path.

Scanning and space

Look 12โ€“15 seconds ahead in the city and further on the highway, sweeping your eyes rather than staring. Keep a following distance of at least three seconds in good conditions and double it in rain, gravel or darkness. Position yourself so you are not in another driver's blind spot, and never linger beside a large truck - if you cannot see the driver's mirrors, the driver cannot see you.

Hazard recognition

The classic hazards tested are: gravel and sand on corners, painted lines and metal gratings when wet, tar snakes, leaves, and the centre of a lane where oil drips from cars. On a curve, slow before you enter, look through the turn to where you want to go, and roll on the throttle smoothly. Braking hard mid-corner is a frequent cause of a low-side fall.

Impairment, fatigue and weather

Alcohol, cannabis, prescription drugs and fatigue all degrade balance and reaction time, and a motorcycle punishes impairment far more than a car does. In rain, reduce speed, increase following distance, and use both brakes gently and progressively.

Worked example: you approach a right-hand corner and see a patch of gravel on your intended line. Correct response: reduce speed before the corner, adjust your line to the cleaner pavement, keep the bike more upright, and avoid sudden braking or throttle changes on the gravel. The trap answer is to brake hard once you are already leaned over.

Rule of thumb: ride as though you are invisible - assume the car at the intersection has not seen you and plan where you will go if it pulls out.

Motorcycle Controls, Handling and Vehicle Familiarity

You must be able to name and operate every control without looking down. The right hand controls the front brake and throttle; the left hand controls the clutch and turn signals, horn and high-beam switch. The right foot works the rear brake; the left foot shifts gears (one down, the rest up on a typical layout). The right grip twists for throttle. Know where the kill switch, fuel valve and choke/enricher are before you ride.

Braking and steering

Use both brakes together, with most stopping power coming from the front - but apply the front progressively to avoid locking it. On a wet or gravelly surface, favour the rear slightly and be gentler with the front. Countersteering is the key handling concept: at speed, push the grip on the side you want to turn toward, and the bike leans and turns that way. At very low speed, you steer by turning the bars in the direction of the turn.

Pre-ride check and low-speed control

Run a quick T-CLOCS-style walkaround: tyres and pressures, controls and cables, lights, oil and fluids, chain or belt tension and slack, and stands. Low-speed control - friction zone, rear brake, head and eyes up - is what examiners watch in a parking-lot test.

Traps: questions often ask which brake to use in a curve (answer: ideally neither hard; if you must, use both gently and stand the bike up slightly) or which wheel the front brake acts on (front only, and it provides most of the stopping force). Another favourite: the throttle does not slow you - closing it does, plus brakes and engine braking.

Rule of thumb: squeeze, don't grab, the front brake; and look where you want to go - the bike follows your eyes.

Signs, Signals, Road Markings and Right-of-Way

Alberta uses standard shape and colour coding, and exam questions test whether you can read a sign at a glance. Octagons mean stop, triangles mean yield, diamonds warn, rectangles give information or regulatory instructions, and pentagons mark school zones. Yellow means warning, orange means construction, and white-on-black or white-on-red rectangles are regulatory.

Signals and pavement markings

A solid yellow centre line means no passing; a broken yellow line on your side means you may pass when safe. A solid white line at the edge marks the shoulder, and a solid white line between lanes means lane changes are discouraged. Crosswalks, stop lines and turn arrows are painted white. At a flashing red light, stop and proceed when safe - treat it as a stop sign. A flashing yellow means proceed with caution; a green arrow gives a protected turn.

Right-of-way essentials

At an uncontrolled intersection, the first vehicle to arrive goes first; if two arrive together, yield to the vehicle on your right. A vehicle turning left yields to oncoming traffic going straight or right. Pedestrians in a crosswalk have the right of way. Emergency vehicles with lights and siren get the right of way - pull to the right and stop.

Traps: a flashing red is not the same as a flashing yellow; a green light does not guarantee a safe left turn if oncoming traffic is still clearing; and a motorcycle must still come to a full stop at a stop sign even when no one is around.

Worked example: you reach a four-way stop at the same moment as a car on your left. You are on the right, so you proceed first - but only after confirming the other driver is actually stopping.

Alberta Class 6 Motorcycle Test cheat sheet

Quick reference

Alberta Traffic Law and Rules of the Road for Motorcycles

  • A Class 6 licence is required to ride a motorcycle on Alberta roads; a Class 5 learner may ride only under the supervision and conditions set by the Class 6 learner stage.

  • A motorcycle rider and passenger must each wear a helmet that meets the standards set out in Alberta's Vehicle Equipment Regulation; the helmet must be properly fastened.

  • Motorcycles must be insured under Alberta's compulsory auto insurance and carry valid registration and a licence plate displayed as required.

  • A motorcycle may carry one passenger only if the bike is designed for two riders and has a proper passenger seat and footrests; lane splitting and riding between lanes are not permitted.

  • Riders must obey the same speed limits, traffic signals, stop signs and right-of-way rules as other vehicles, and must not ride on sidewalks or pedestrian crosswalks.

  • Following too closely is a contravention; motorcycles need at least the same following distance as cars and more when the road is wet, gravel-covered or windy.

  • Alberta's impaired driving laws apply to motorcycle riders; a Graduated Driver Licensing rider has a zero-alcohol condition.

  • A rider must signal intention to turn or change lanes, and must cancel the signal after completing the manoeuvre; hand signals are used if turn signals are not working.

  • Motorcycles must be equipped with a working headlight, tail light, brake light, horn and at least one rear-view mirror as required by equipment rules.

Quick reference

Safe Riding Practices and Hazard Awareness

  • Use the two-second following rule at minimum; double it to four seconds in rain, gravel, strong crosswinds or reduced visibility.

  • Ride in the left portion of your lane to be seen in mirrors and to keep an escape path, but avoid the centre line where oil drips accumulate at intersections.

  • Target fixation is a hazard: look where you want to go, not at the obstacle, because the motorcycle follows the rider's gaze.

  • Scan 12-20 seconds ahead for gravel, sand, painted lines, metal grates, railway tracks and potholes; cross tracks and grates at as close to 90 degrees as possible.

  • In a curve, slow before the entry, look through the turn to the exit, and apply smooth maintenance throttle; braking hard mid-corner reduces traction and stands the bike up.

  • Cold tires and cold pavement have reduced grip; the first minutes of a ride and the first rain after a dry spell are the slickest conditions.

  • A rider's visible profile is narrow; use lane position, bright or reflective clothing and a headlight to increase conspicuity, and never assume a driver has seen you.

  • Group riding uses a staggered formation on straight roads and single file in curves, with each rider keeping their own following distance.

  • Fatigue, cold and alcohol all degrade balance and reaction time; reaction distance grows with speed, so total stopping distance is perception plus reaction plus braking.

Quick reference

Motorcycle Controls, Handling and Vehicle Familiarity

  • The right hand controls the front brake and throttle; the left hand controls the clutch and turn signals; the right foot is the rear brake and the left foot the shift lever.

  • The front brake provides most of the stopping power; apply it progressively and use both brakes together for maximum straight-line stopping.

  • Countersteering: to turn right at speed, push the right grip forward; the bike leans right and turns right.

  • The friction zone is the range of clutch lever travel where power begins to transfer; it is used for slow-speed control and starts on a hill.

  • At slow speed, use the rear brake and clutch friction zone together to stabilize the bike; at higher speed, lean angle and throttle control the turn.

  • Squeeze the fuel tank with the knees, keep arms relaxed and look up and ahead; a tight grip on the bars transmits rider input and unsettles the bike.

  • Before riding, check tires (pressure and tread), controls, lights, oil and fuel, and the chain or belt; the pre-ride check is a legal and safety habit.

  • Engine braking by rolling off the throttle slows the rear wheel; downshift one gear at a time and match engine speed to road speed to avoid rear-wheel lockup.

  • A skid on the front wheel usually results from over-braking or braking on a slippery surface; release the brake smoothly to let the wheel regain rolling grip.

Quick reference

Signs, Signals, Road Markings and Right-of-Way

  • A red octagon means stop completely; a red-and-white triangle (yield) means slow and give way to traffic that has the right of way.

  • Yellow diamond signs warn of hazards ahead; orange signs mark construction zones, and reduced speed limits in those zones are enforceable when posted.

  • A solid yellow centre line means no passing in either direction; a broken yellow line on your side permits passing when it is safe.

  • A solid white line at the edge of the lane marks the shoulder; a broken white line separates lanes travelling in the same direction.

  • A flashing red signal is treated as a stop sign; a flashing yellow means proceed with caution and yield as required.

  • At an uncontrolled intersection, the first vehicle to arrive has the right of way; if two arrive at the same time, the vehicle on the right goes first.

  • A vehicle turning left must yield to oncoming traffic going straight or turning right; pedestrians in a marked or unmarked crosswalk have the right of way.

  • A stop line or crosswalk line marks where to stop; if there is no line, stop before the crosswalk or the edge of the intersecting road.

  • Railway crossbucks and flashing lights require a stop when signals are active; never pass a school bus with its red lights flashing.

Quick reference

Alberta Traffic Law and Rules of the Road for Motorcycles

  • A Class 6 licence is required to ride a motorcycle on Alberta roads; a Class 5 learner may ride only under the supervision and conditions set by the Class 6 learner stage.

  • A motorcycle rider and passenger must each wear a helmet that meets the standards set out in Alberta's Vehicle Equipment Regulation; the helmet must be properly fastened.

  • Motorcycles must be insured under Alberta's compulsory auto insurance and carry valid registration and a licence plate displayed as required.

  • A motorcycle may carry one passenger only if the bike is designed for two riders and has a proper passenger seat and footrests; lane splitting and riding between lanes are not permitted.

  • Riders must obey the same speed limits, traffic signals, stop signs and right-of-way rules as other vehicles, and must not ride on sidewalks or pedestrian crosswalks.

  • Following too closely is a contravention; motorcycles need at least the same following distance as cars and more when the road is wet, gravel-covered or windy.

  • Alberta's impaired driving laws apply to motorcycle riders; a Graduated Driver Licensing rider has a zero-alcohol condition.

  • A rider must signal intention to turn or change lanes, and must cancel the signal after completing the manoeuvre; hand signals are used if turn signals are not working.

  • Motorcycles must be equipped with a working headlight, tail light, brake light, horn and at least one rear-view mirror as required by equipment rules.

Quick reference

Safe Riding Practices and Hazard Awareness

  • Use the two-second following rule at minimum; double it to four seconds in rain, gravel, strong crosswinds or reduced visibility.

  • Ride in the left portion of your lane to be seen in mirrors and to keep an escape path, but avoid the centre line where oil drips accumulate at intersections.

  • Target fixation is a hazard: look where you want to go, not at the obstacle, because the motorcycle follows the rider's gaze.

  • Scan 12-20 seconds ahead for gravel, sand, painted lines, metal grates, railway tracks and potholes; cross tracks and grates at as close to 90 degrees as possible.

  • In a curve, slow before the entry, look through the turn to the exit, and apply smooth maintenance throttle; braking hard mid-corner reduces traction and stands the bike up.

  • Cold tires and cold pavement have reduced grip; the first minutes of a ride and the first rain after a dry spell are the slickest conditions.

  • A rider's visible profile is narrow; use lane position, bright or reflective clothing and a headlight to increase conspicuity, and never assume a driver has seen you.

  • Group riding uses a staggered formation on straight roads and single file in curves, with each rider keeping their own following distance.

  • Fatigue, cold and alcohol all degrade balance and reaction time; reaction distance grows with speed, so total stopping distance is perception plus reaction plus braking.

Quick reference

Motorcycle Controls, Handling and Vehicle Familiarity

  • The right hand controls the front brake and throttle; the left hand controls the clutch and turn signals; the right foot is the rear brake and the left foot the shift lever.

  • The front brake provides most of the stopping power; apply it progressively and use both brakes together for maximum straight-line stopping.

  • Countersteering: to turn right at speed, push the right grip forward; the bike leans right and turns right.

  • The friction zone is the range of clutch lever travel where power begins to transfer; it is used for slow-speed control and starts on a hill.

  • At slow speed, use the rear brake and clutch friction zone together to stabilize the bike; at higher speed, lean angle and throttle control the turn.

  • Squeeze the fuel tank with the knees, keep arms relaxed and look up and ahead; a tight grip on the bars transmits rider input and unsettles the bike.

  • Before riding, check tires (pressure and tread), controls, lights, oil and fuel, and the chain or belt; the pre-ride check is a legal and safety habit.

  • Engine braking by rolling off the throttle slows the rear wheel; downshift one gear at a time and match engine speed to road speed to avoid rear-wheel lockup.

  • A skid on the front wheel usually results from over-braking or braking on a slippery surface; release the brake smoothly to let the wheel regain rolling grip.

Quick reference

Signs, Signals, Road Markings and Right-of-Way

  • A red octagon means stop completely; a red-and-white triangle (yield) means slow and give way to traffic that has the right of way.

  • Yellow diamond signs warn of hazards ahead; orange signs mark construction zones, and reduced speed limits in those zones are enforceable when posted.

  • A solid yellow centre line means no passing in either direction; a broken yellow line on your side permits passing when it is safe.

  • A solid white line at the edge of the lane marks the shoulder; a broken white line separates lanes travelling in the same direction.

  • A flashing red signal is treated as a stop sign; a flashing yellow means proceed with caution and yield as required.

  • At an uncontrolled intersection, the first vehicle to arrive has the right of way; if two arrive at the same time, the vehicle on the right goes first.

  • A vehicle turning left must yield to oncoming traffic going straight or turning right; pedestrians in a marked or unmarked crosswalk have the right of way.

  • A stop line or crosswalk line marks where to stop; if there is no line, stop before the crosswalk or the edge of the intersecting road.

  • Railway crossbucks and flashing lights require a stop when signals are active; never pass a school bus with its red lights flashing.

Alberta Class 6 Motorcycle Test key terms

Countersteering

The technique of pushing the handlebar grip on the side you want to turn toward, which leans the motorcycle and steers it through the curve. It is the normal way to initiate turns at anything above walking speed.

Related: Lean Angle, Target Fixation
Target Fixation

The tendency for a rider to steer toward whatever they are staring at. Because of it, riders must look through a curve toward the exit rather than at a hazard or the road edge.

Related: Countersteering, Escape Path
Lean Angle

The amount a motorcycle tilts from vertical while turning. It increases with speed and with tighter curves, and is limited by tire grip, ground clearance and road surface condition.

Related: Countersteering, Traction
Traction

The grip between the tires and the road surface that allows acceleration, braking and turning. It is reduced by rain, gravel, painted lines, metal surfaces and cold tires.

Related: Lean Angle, Threshold Braking
Threshold Braking

Braking as hard as possible without locking a wheel or losing grip. On a motorcycle most stopping power comes from the front brake, so the rider applies it progressively while easing weight forward.

Related: Traction, Engine Braking
Engine Braking

The slowing effect created when a rider closes the throttle and the engine resists the turning of the rear wheel. Downshifting one gear at a time uses this to control speed before a curve.

Related: Threshold Braking, Rev Matching
Rev Matching

Briefly raising engine speed with the throttle during a downshift so the engine speed matches the lower gear. It keeps the rear wheel from hopping or skidding and makes the shift smoother.

Related: Engine Braking, Clutch Friction Zone
Clutch Friction Zone

The range of lever travel where the clutch is partly engaged and begins to transmit power. Riders use it for smooth starts, low-speed control and slow-speed manoeuvres in traffic.

Related: Rev Matching, Riding the Clutch
Riding the Clutch

Holding the clutch lever partly pulled in for long periods so the clutch slips continuously. It wears the clutch plates and reduces control, so it should be limited to brief low-speed manoeuvres.

Related: Clutch Friction Zone
Trail Braking

Continuing to apply light brake pressure as the motorcycle leans into a curve, then releasing it smoothly. It is an advanced technique that requires good traction and must be done gently to avoid upsetting the bike.

Related: Traction, Lean Angle
Escape Path

A planned route out of danger, such as the gap beside a vehicle or the shoulder, that a rider identifies before a hazard develops. Choosing one in advance gives the rider somewhere to go if braking is not enough.

Related: Target Fixation, Following Distance
Following Distance

The space a rider keeps behind the vehicle ahead. Motorcycles should allow at least a two-second gap in good conditions and more in rain, darkness or heavy traffic to leave room to stop.

Related: Escape Path, Blind Spot
Blind Spot

The area beside and behind a vehicle that the driver cannot see in the mirrors. Riders should avoid lingering there and should move through it promptly when passing.

Related: Following Distance, Lane Positioning
Lane Positioning

Choosing where to ride within a lane, such as the left, centre or right portion. Riders shift position to be more visible, to increase space from hazards and to set up a better view through curves.

Related: Blind Spot, Road Hazard
Lane Splitting

Riding between two lanes of moving traffic or sharing a lane with another vehicle. In Alberta, a motorcycle is entitled to the full width of a lane and may not share it with another vehicle.

Related: Lane Positioning, Lane Change
Lane Change

Moving from one marked lane to another. A rider must signal, check mirrors and shoulder-check the blind spot, and yield to traffic already in the lane before moving over.

Related: Blind Spot, Shoulder Check
Shoulder Check

A quick turn of the head to look directly into a blind spot that mirrors do not cover. Riders use it before lane changes, turns and merging, keeping it brief to stay aware of traffic ahead.

Related: Blind Spot, Lane Change
Right-of-Way

The legal priority to proceed through an intersection or along a roadway. Riders must yield it when required, and should never assume another driver will give way even when the law says they should.

Related: Uncontrolled Intersection, Yield Sign
Uncontrolled Intersection

An intersection with no stop signs, yield signs or traffic lights. Drivers and riders must slow down, be ready to stop, and yield to vehicles already in the intersection or approaching from the right.

Related: Right-of-Way, Four-Way Stop
Four-Way Stop

An intersection where all approaches have stop signs. Vehicles proceed in the order they arrived, and if two arrive at the same time the one on the right goes first.

Related: Uncontrolled Intersection, Right-of-Way
Yield Sign

A sign requiring a driver or rider to slow down and give way to traffic on the intersecting road or to pedestrians. Stopping is required only if traffic is present.

Related: Right-of-Way, Stop Sign
Stop Sign

A red octagonal sign meaning the vehicle must come to a complete stop before the crosswalk or stop line, then proceed only when the way is safe and clear.

Related: Yield Sign, Four-Way Stop
Solid White Line

A road marking that separates lanes travelling in the same direction and discourages lane changes. Riders should treat it as a boundary and cross it only when it is safe and legal to do so.

Related: Broken White Line, Solid Yellow Line
Broken White Line

A dashed white marking between lanes moving in the same direction. It shows that lane changes are permitted when it is safe, after signalling and checking the blind spot.

Related: Solid White Line, Lane Change
Solid Yellow Line

A yellow marking separating traffic moving in opposite directions. A solid yellow line on your side means passing is not allowed because visibility or road conditions make it unsafe.

Related: Broken Yellow Line, Passing
Broken Yellow Line

A dashed yellow marking between opposing traffic flows. Where it appears on your side of the centre line, passing is permitted when the way ahead is clearly visible and safe.

Related: Solid Yellow Line, Passing
Passing

Overtaking another vehicle travelling the same direction. A rider must have a clear view, a legal passing zone, enough space to complete the move, and must not pass on the shoulder or across a solid line.

Related: Solid Yellow Line, Broken Yellow Line
Road Hazard

Any condition that reduces grip or space, such as gravel, sand, potholes, wet leaves, ice, painted lines, railway tracks or metal gratings. Riders should slow before reaching it and cross it as upright as possible.

Related: Traction, Lane Positioning
Railway Crossing

A place where tracks cross the road. Riders should slow down, look both ways, and cross the tracks as close to a right angle as possible to avoid the front wheel catching in the rail.

Related: Road Hazard, Traction
Gravel Shoulder

The unpaved edge of the roadway, often loose and unstable. Riders should avoid riding or braking on it and should re-enter the paved surface gradually and at a shallow angle.

Related: Road Hazard, Traction
Head Check

Another name for a shoulder check, a direct glance over the shoulder to confirm a blind spot is clear before changing position or direction.

Related: Shoulder Check, Blind Spot
Hand Signals

Arm signals used to show turning and stopping intentions, required when a motorcycle's turn signals are not working. Left arm straight out means left turn, bent up means right turn, and angled down means slowing.

Related: Turn Signal, Lane Change
Turn Signal

A flashing light that shows other road users your intention to turn or change lanes. Riders must signal before the manoeuvre and cancel the signal afterwards, since motorcycle signals often do not self-cancel.

Related: Hand Signals, Lane Change
Full Face Helmet

A helmet that covers the whole head and face with a chin bar and visor. Alberta law requires an approved helmet for motorcycle riders and passengers, and a proper fit is essential for protection.

Related: Eye Protection, Protective Clothing
Eye Protection

A visor, goggles or approved glasses that shield the eyes from wind, dust and insects. Alberta requires eye protection for motorcycle riders unless the motorcycle has a windshield or the helmet has a face shield.

Related: Full Face Helmet, Protective Clothing
Protective Clothing

Gear such as a sturdy jacket, long pants, gloves, boots and high-visibility material that reduces injury in a fall. It also protects against wind, cold and road debris during normal riding.

Related: Full Face Helmet, Eye Protection
Pre-Ride Check

A quick inspection before riding that covers tires and tire pressure, brakes, controls, lights, mirrors, fluid levels, chain or belt tension and the fuel supply. It catches problems before they become failures on the road.

Related: Tire Contact Patch, Countersteering
Tire Contact Patch

The small area of each tire actually touching the road. Because it is small, tire condition and correct inflation pressure matter greatly for grip, braking and steering on a motorcycle.

Related: Traction, Pre-Ride Check
Counterweighting

Shifting body weight to the outside of a slow, tight turn to help balance the motorcycle. It is used in low-speed manoeuvres such as U-turns and parking lot riding, not in normal road curves.

Related: Lean Angle, Countersteering
Fatigue

Physical and mental tiredness that slows reaction time and judgement. It is a serious risk on long rides, so riders should plan breaks, stay hydrated and stop when concentration starts to fade.

Related: Following Distance, Protective Clothing

Alberta Class 6 Motorcycle Test study plan

8 weeks ยท About 6 hours per week

Week 1

Alberta traffic laws and rules of the road applicable to motorcycles & Motorcycle controls, handling and vehicle familiarity

  • Map every Alberta rule that differs for motorcycles (lane positioning, passenger rules, helmet and equipment requirements) into a one-page reference sheet

  • Identify each primary control on a motorcycle (throttle, clutch, front and rear brake, shifter, turn signals) and state its function in writing

  • Demonstrate the friction-zone start and smooth clutch release in a parking lot for 20 minutes per session

  • Explain the difference between front-brake and rear-brake stopping power and when each is emphasized

Your checkpoint

A one-page motorcycle rules-and-controls reference sheet, written from memory and checked against notes

Week 2

Alberta traffic laws and rules of the road applicable to motorcycles & Motorcycle controls, handling and vehicle familiarity

  • Describe Alberta's lane-position and lane-sharing rules for motorcycles and state where a rider may legally position within a lane

  • Practice low-speed balance drills (figure-eights and slow straight-line riding) in a controlled lot

  • Perform controlled emergency stops from 30 km/h using both brakes, ten repetitions

  • Recite the pre-ride inspection checklist (tires, brakes, controls, lights, chain/belt, fluids) without notes

Your checkpoint

A logged practice session sheet recording 10 emergency stops and 20 minutes of low-speed drills with self-ratings

Week 3

Motorcycle controls, handling and vehicle familiarity & Signs, signals, road markings and right-of-way

  • Interpret the meaning of lane markings (solid, dashed, double, turn lanes) as they affect motorcycle positioning

  • Read and explain 15 common regulatory and warning signs without reference material

  • Practice countersteering at speeds above 20 km/h and describe the technique in writing

  • Execute controlled swerves around a marked obstacle at moderate speed

Your checkpoint

A 15-sign flashcard set plus a written paragraph explaining countersteering in your own words

Week 4

Safe motorcycle riding practices and hazard awareness & Signs, signals, road markings and right-of-way

  • Identify the three most common collision configurations involving motorcycles (left-turn across path, intersection incursion, rear-end) and state a defensive response for each

  • Apply the see-think-do hazard scanning routine to five described riding scenarios

  • Explain right-of-way rules at uncontrolled intersections, four-way stops, and when turning left across oncoming traffic

  • Describe how to establish and maintain a following distance appropriate for a motorcycle

Your checkpoint

A hazard-response table listing five scenarios, the hazard, and the planned action for each

Week 5

Safe motorcycle riding practices and hazard awareness & Motorcycle controls, handling and vehicle familiarity

  • Explain how surface hazards (gravel, wet paint, metal grates, tar snakes) affect traction and describe the correct response for each

  • Practice braking on a wet or loose surface at low speed and note the difference in feel and distance

  • Describe the effects of alcohol, fatigue, and cold on riding judgment and reaction time

  • State the visibility strategies for riding in rain, at dusk, and in a vehicle's blind spot

Your checkpoint

A written hazard-conditions guide covering five surface hazards and the correct response to each

Week 6

Alberta traffic laws and rules of the road applicable to motorcycles & Safe motorcycle riding practices and hazard awareness

  • Recite the Alberta licensing and equipment requirements for a Class 6 rider, including passenger and helmet rules

  • Explain the legal and safety considerations for carrying a passenger and for carrying cargo

  • Describe the risks of riding in groups and state the staggered-formation and spacing rules

  • List the factors that increase impairment risk on a motorcycle and the legal consequences of an impaired riding charge

Your checkpoint

A one-page passenger, cargo, and group-riding summary written without notes

Week 7

Signs, signals, road markings and right-of-way & Alberta traffic laws and rules of the road applicable to motorcycles

  • Work through 40 right-of-way and sign-interpretation practice items and score at least 90 percent

  • Explain how traffic signals, pavement markings, and signage interact at complex intersections

  • Describe the correct positioning and signaling for left and right turns from a motorcycle

  • Identify situations where a motorcycle may legally use a full lane or share a lane, and where it may not

Your checkpoint

A scored 40-item practice set with every missed item corrected and explained in writing

Week 8

Alberta traffic laws and rules of the road applicable to motorcycles & Safe motorcycle riding practices and hazard awareness & Motorcycle controls, handling and vehicle familiarity & Signs, signals, road markings and right-of-way

  • Complete two full-length timed practice tests and score at least 85 percent on each

  • Review every missed item from both tests and write the correct rule or technique for each

  • Re-run the parking-lot skill drills (emergency stop, swerve, low-speed figure-eight) and compare against week 2 ratings

  • Recite the pre-ride checklist and the top five hazard responses from memory

Your checkpoint

Two completed timed practice tests with a written corrections log for every missed item

Milestones

Week 2: Can state the motorcycle-specific Alberta rules and perform a clean emergency stop from 30 km/h on demand

Week 4: Can explain countersteering, interpret 15 common signs, and name a defensive response to the three main motorcycle collision types

Week 6: Can describe the correct response to five surface hazards and recite passenger, cargo, and group-riding rules without notes

Week 8: Scores 85 percent or higher on two full-length timed practice tests and has a complete corrections log

Alberta Class 6 Motorcycle Test exam day

Your checklist

Valid Class 6 learner's licence or equivalent

Bring your current Alberta licence (or the learner's permit you were issued). The examiner will check that it is valid and unexpired before the test begins.

Government-issued photo ID

If your licence is your photo ID, that is usually sufficient. Confirm with the provider whether a second piece of ID is required.

Proof of registration and insurance for the motorcycle

The motorcycle used for the road test must be legally registered and insured. Bring the registration certificate and proof of insurance; confirm with the provider which documents they accept.

Roadworthy motorcycle

The bike must be in safe working order - lights, signals, brakes, horn, tires, mirrors, and a legal exhaust. A defective motorcycle can cause the test to be cancelled.

Approved helmet and riding gear

Wear a properly fitting motorcycle helmet that meets the applicable safety standard, plus eye protection, gloves, and sturdy footwear and clothing.

Appointment confirmation and fee payment

Bring your booking confirmation and be ready to pay any test fee. Confirm with the provider how and when payment is taken.

Arrive early at the correct location

Plan to arrive ahead of your appointment time at the address on your confirmation. Allow extra time for traffic and parking.

Know the motorcycle skills and road-test format

Review what the test covers (low-speed control, observation, traffic rules) so you are not surprised by the sequence. Confirm the exact format with the provider.

Check weather and road conditions

Tests may be affected by snow, ice, heavy rain, or high wind. Confirm with the provider whether your test will proceed in poor conditions.

Rest and avoid alcohol or drugs

Do not consume alcohol or impairing substances before the test. Being impaired will end the test and may have licensing consequences.

Bring a way to contact the provider

Have the provider's phone number handy in case of delay, breakdown, or a last-minute question.

Plan the day

72 hours before

Confirm your appointment time, location, and fee with the provider. Re-read the motorcycle rider's guide and practise the low-speed manoeuvres and observation checks you find hardest.

72 hours before

Do a full safety check of the motorcycle you will ride: tires, brakes, lights, signals, horn, mirrors, chain/belt, and fluid levels. Fix anything questionable now.

24 hours before

Lay out your licence, ID, registration, insurance, helmet, and riding gear. Check the weather forecast and plan your route and arrival time. Get a full night's sleep.

Morning of

Eat a normal meal, avoid alcohol entirely, and arrive early. Do a final walk-around of the motorcycle and warm up with a short, legal ride if you are comfortable doing so.

During the test

Follow the examiner's instructions exactly, ride predictably and within the law, make clear shoulder checks and signal your intentions, and keep a safe following distance. Ask for clarification if an instruction is unclear.

Rules to check

  • Bring valid, unexpired identification and your licence; you may be turned away without them.

  • The motorcycle must be legally registered, insured, and in safe working condition, or the test may be cancelled.

  • Wear an approved helmet and appropriate protective gear at all times while riding.

  • Do not consume alcohol or impairing drugs before the test; impairment ends the test.

  • Follow the examiner's directions and ride according to traffic law; unsafe or illegal riding can end the test early.

  • Ask the provider in advance about breaks, rescheduling, cancellation, and refund policies, and about what happens if weather or a mechanical problem interrupts the test.

  • Scoring and pass/fail criteria are set by the provider; confirm the details and any appeal process with them.

  • Listen carefully to instructions and ask for clarification if needed - misunderstanding an instruction is not usually grounds for a re-test.

Alberta Class 6 Motorcycle Test FAQ

How many Alberta Class 6 Motorcycle Test practice questions are available?

The practice set has 200 Alberta Class 6 Motorcycle Test questions. Each one includes the choices, the correct answer, and an explanation, and the set is free to read with no signup.

How many Alberta Class 6 Motorcycle Test flashcards are available?

The flashcard set has 32 Alberta Class 6 Motorcycle Test cards. Each card shows the term and its definition.

Which topics does the Alberta Class 6 Motorcycle Test study material cover?

The Alberta Class 6 Motorcycle Test study material has 4 sections, including Alberta Traffic Law and Rules of the Road for Motorcyclists, Safe Riding Practices and Hazard Awareness, and Motorcycle Controls, Handling and Vehicle Familiarity.

What format facts does the catalog list for the Alberta Class 6 Motorcycle Test exam?

The catalog lists these item types: multiple choice for the Alberta Class 6 Motorcycle Test exam.